SmartDome Camera
SCC-C6405(P)
E
Owner’s Instructions
RU
PL
êÛÍÓ‚Ó‰ÒÚ‚ÓÔÓθÁÓ‚‡ÚÂÎfl
Instrukcja obs∏ugi
Part : AB68-00504D (04)
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Do not place conductive objects (e.g., screwdrivers, coins, and metal
things) or containers filled with water on top of the camera. (Doing so may
cause personal injury due to fire, electrical shock, or falling objects.)
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
7. Do not install the unit in humid, dusty, or sooty locations.
(Doing so may cause fire or electrical shock.)
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
8. If any unusual smells or smoke come from the unit, stop using the product.
In such case, immediately disconnect the power source and contact the
service center. (Continued use in such a condition may cause fire or
electrical shock.)
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
E
9. If this product fails to operate normally, contact the store of purchase or
your nearest service center. Never disassemble or modify this product in
any way. (SAMSUNG is not liable for problems caused by unauthorized
modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product.
(Doing so may cause fire or electrical shock.)
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Wipe the surface with a dry cloth. Never use detergents or chemical
cleaners on the product, as this may result in discoloration of surface or
cause damage to the finish.
Caution
1. Do not drop objects on the product or apply strong shock to it. Keep away
from a location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 122°F), low
temperature (below 14°F), or high humidity.
(Doing so may cause fire or electrical shock.)
3. Avoid a location which is exposed to direct sunlight, or near heat sources
such as heaters or radiators.
(Neglecting to do so may result in a risk of fire.)
4. If you want to relocate the already installed product, be sure to turn off the
power and then move or reinstall it.
5. Install in a well-ventilated location.
6. Remove the power plug from the outlet when there is a lightning storm.
(Neglecting to do so may cause fire or damage to the product.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Usage
This is a basic instruction manual for the SCC-C6405(P) user.
It contains all the instructions needed to use the SCC-C6405(P)
from a simple introduction of the control locations and functions of
the SCC-C6405(P) to installation methods in the set up menu.
E
We recommend all users of the SCC-C6405(P) from the
advanced user who has used similar cameras before to the
general user to read the instruction manual before using.
The most frequently used feature in the SCC-C6405(P) would be
the SCC-C6405(P) Setup Menu.
The SCC-C6405(P) Setup Menu is explained in detailed in
"Chapter 3 Setup Menu Overview".
The instructional manual is best used when read from beginning
to end, but for users wanting to read only the part they need here
are the Chapter summaries.
"Chapter 1 SCC-C6405(P) Overview" includes a brief
introduction of the SCC-C6405(P), part names and functions, and
Switch Settings.
"Chapter 2 SCC-C6405(P) Installation" explains the installation
procedures of the SCC-C6405(P) and provides preparation and
installation environment requirements.
"Chapter 3 Setup Menu Overview" presents the structure of the
Setup menu for the SCC-C6405(P) including a detailed
explanation of the functions performed in each submenu.
"Appendix SCC-C6405(P) Product Specifications" contains
product specifications of the SCC-C6405(P) in itemized
categories.
1-1
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
4. ZONE SET ..................................................................................3-17
- PRIVACY ZONE .......................................................................3-17
- STYLE.......................................................................................3-17
- BLANK ALL ABOVE..................................................................3-18
- BLANK ALL BELOW.................................................................3-18
- PRYVACY ZONE MAP3 ...........................................................3-18
- SET ZONE AREA .....................................................................3-19
- SET ZOOM ...............................................................................3-20
- REVERSE.................................................................................3-20
- EXIT ..........................................................................................3-20
- ZONE DIR SET/ZONE AREA SET ...........................................3-20
- ZONE DIR SET.........................................................................3-21
- ZONE AREA .............................................................................3-21
- LOCATION................................................................................3-22
- ZONE ID SET............................................................................3-22
- ZONE ENABLE.........................................................................3-22
5. AUTO SET ..................................................................................3-23
- AUTO PAN................................................................................3-23
- START SET ..............................................................................3-23
- END SET...................................................................................3-23
- DIRECTION ..............................................................................3-24
- ENDLESS .................................................................................3-24
- SPEED......................................................................................3-24
- DWELL TIME ............................................................................3-24
- PATTERN .................................................................................3-24
- SCAN ........................................................................................3-25
- AUTO PLAY..............................................................................3-26
- AUTO RETURN ........................................................................3-26
- PLAY NUMBER ........................................................................3-26
6. ALARM SET................................................................................3-27
- ALARM PRIORITY SET............................................................3-27
- ALARM IN SET .........................................................................3-27
- ALARM OUT SET .....................................................................3-27
- AUTO SET ................................................................................3-28
- AUX OUT CONTROL................................................................3-28
7. OTHER SET................................................................................3-28
- PROPORTINAL P/T..................................................................3-28
- TURBO P/T...............................................................................3-29
- AUTO CAL ................................................................................3-29
- D-FLIP.......................................................................................3-29
- CAM RESET .............................................................................3-29
- LANGUAGE ..............................................................................3-29
- PASSWORD .............................................................................3-29
8. SYSTEM INFO............................................................................3-30
9. SHORT KEYS .............................................................................3-31
Before Usage...............................................................................................1-1
Chapter 1 SCC-C6405(P) Overview...........................................................1-5
SCC-C6405(P) Introduction...........................................................1-6
Locations of Control.......................................................................1-7
FRONT...........................................................................................1-7
BACK .............................................................................................1-8
ADAPTER CONNECTION.............................................................1-9
INITIAL SETTING ..........................................................................1-10
Setting RS-422A/RS-485 termination ............................................1-11
E
Chapter 2 SCC-C6405(P) Installation........................................................2-1
Before Installing .............................................................................2-2
Preparing the Cables .....................................................................2-3
Cable Connection ..........................................................................2-4
Installing SCC-C6405(P)................................................................2-5
Installing the Camera.....................................................................2-8
Chapter 3 Setup Menu Overview................................................................3-1
Structure of the Setup Menu..........................................................3-2
1. CAMERA SET ...........................................................................3-4
- CAMERA ID.............................................................................3-4
- V-SYNC ...................................................................................3-5
- COLOR/BW .............................................................................3-6
- MOTION DET ..........................................................................3-7
- ZOOM SPEED.........................................................................3-8
- DIGITAL ZOOM.......................................................................3-8
- EXIT.........................................................................................3-8
2. VIDEO SET ...............................................................................3-9
- IRIS..........................................................................................3-9
- ALC..........................................................................................3-9
- BLC..........................................................................................3-9
- WDR ........................................................................................3-9
- SHUTTER................................................................................3-10
- AGC.........................................................................................3-11
- MOTION ..................................................................................3-11
- WHITE BAL .............................................................................3-12
- DIS...........................................................................................3-13
- FOCUS MODE ........................................................................3-14
- SPECIAL..................................................................................3-14
- EXIT.........................................................................................3-14
3. PRESET.....................................................................................3-15
- POSITION SET........................................................................3-16
- PRESET ID..............................................................................3-16
- VIDEO SET..............................................................................3-16
- PRESET SPEED .....................................................................3-16
- DWELL TIME...........................................................................3-16
- IMAGE HOLD ..........................................................................3-16
- EXIT.........................................................................................3-16
Product specifications ............................................................................3-34
1-3
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SCC-C6405(P) Introduction
Chapter 1 SCC-C6405(P) Overview
SCC-C6405(P) is a zoom lens built in smart dome camera which
provides you with the best monitoring function in connection with
CCTV at banks or companies.
In this chapter we will briefly introduce the SCC-C6405(P) and
show main functions, locations of control and Switch Setting.
E
The SCC-C6405(P) is a high quality surveillance camera using x22
zoom lens and digital zoom IC, it can catch clear images up to 220
times.
SCC-C6405(P) has a variety of functions such as;
- WDR to cover the full screen irregardless of its brightness,
- COLOR/BW to improve the sensitivity by automatic conversion
into the black and white mode at night or in the environment with
low illumination,
- White Balance to control the brightness to the illumination,
- Backlight Compensation under spotlight or utmost bright
illumination,
- Auto Focus to automatically adjust the focus to the subject
movement,
- Privacy zone to hide a specific area for personal privacy, and,
- PAN/TILT for precise control at high speed.
The SCC-C6405(P) uses an Alarm function for alert situations and
moving camera in the direction you want, ZOOM-IN and
ZOOM-OUT functions can be remote controlled.
* The followings may occur in a camera with built-in zoom.
- When the zoom rate becomes closer to the TELE side, the edges of
the screen may become dim.
- When connected to a DVR or an LCD monitor, the screen corners
may be obstructed.
1-5
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Locations of Control
FRONT
BACK
AC 24V
OUT
POWER
E
AC 24V
OUT
POWER
1-7
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
ADAPTER CONNECTION
INITIAL SETTING
CAMERA ADDRESS SETUP
Use SW701, SW702, or 703 for Camera Address setup. You may allocate
up to 255 addresses by using SW701 to set the 3rd digit, SW702 the 2nd
digit, and SW703 the 1st digit.
EX) In case of Camera Address 1, see the following figure for setup.
SCC-C6405(P) Adapter BOARD
E
SW701
SW702
SW703
Setting communication Protocol
Use number 1~4 PIN of SW704 to set communication Protocol.
PIN
Comp
PIN1 PIN2 PIN3 PIN4
A : SAMSUNG HALF
A
B
C
D
E
F
G
H
I
OFF OFF OFF OFF
B : SAMSUNG FULL
ON
OFF
ON
OFF OFF OFF
ON
ON
OFF OFF
OFF OFF
SEE INSTRUCTION MANUAL
ON 1 2 3 4 5 6 7 8
OFF OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
SW704
ON
OFF
ON
OFF
ON
(x100) (x10)
(x1)
ON
SW701 SW702 SW703
OFF OFF OFF
J
ON
OFF
ON
OFF OFF
ON
K
L
ON
ON
OFF
OFF
ON
ON
ON
M
N
O
P
OFF OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
(BOTTOM VIEW)
ON
ON
ON
Baud Rate Setting
Use PIN 5 and 6 of SW704.
1
2
3
4
5
6
7
8
ON
OFF
SW 704
PIN 6
ON
BAUD RATE
4800 BPS
PIN 5
ON
ON
9600 BPS
OFF
ON
OFF
OFF
19200 BPS
38400 BPS
OFF
1-9
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting RS-422A/RS-485 termination
Chapter 2 SCC-C6405(P) Installation
1
2
As it is shown in the structure map, when Controller and RS-422A/RS-
485 is connected it should be terminated according to the Cable feature
of impedance on the each end of the transmitting line to transfer the
signals in long distance by controlling the reflection of the signals to the
lowest.
E
In this chapter, we will check the contents of the package before
installing the SCC-C6405(P), and prepare a power adapter suitable
for the power supply system.
(Power Consumption: 18W; Voltage: AC24V, 1.5A)
Then, we will install the SCC-C6405(P) and connect the cables.
Division
n < 32
Termination
SW1-ON
<RS-485 Half Duplex Organization>
Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.
n < 32
Division
SW1-ON
SW2-ON
Division
<RS-422A/RS-485 Full Duplex Organization>
1-11
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the Cables
Before Installing
To install and use the SCC-C6405(P), the following cables should be
prepared.
Checking Package Contents
Please check that all components listed below are included in the package:
Power Adapter Cable
The cable that plugs into the SCC-C6405(P) power input receptacle has
the rated voltage of AC24V, 1.5A.
Check the rated voltage before using the cable.
E
SCC-C6405(P)
Bracket anchor
Owner’s
Instructions
AC 24V
OUT
Video Cable
POWER
The SCC-C6405(P)'s cable is a BNC Cable for connecting the video-
output terminal to the video-input terminal of the monitor.
Screws
Cover Body
Camera Holder
Adapter Board
2-2
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing SCC-C6405(P)
Cable Connection
1. First, connect one end of the
BNC video cable connector to
the Video Output Terminal
(VIDEO OUT)
Installation Precautions
1) Make sure that the installation site can sufficiently support a minimum of
four times the net weight of the SCC-C6405(P) SmartDome Camera
and other accessories.
2. Then, connect the other end of
the connector to the Video Input
Terminal of the monitor.
2) Install in an area where the space above the ceiling board is over 18 cm
(7 in.) high.
3) Use the supplied screws to fasten the camera to the bracket assembly.
4) Keep persons away from the installation area, as there is a risk of falling
objects.
E
Also, move valuables to a safe location before installation.
Separately Sold Products for Installation
3. Now connect the Power Adapter
Cable. Use a driver to screw
one part of the two lines of
Depending on the installation site, it may be convenient to use one of the
following products.
Power Adapter to Power Input
Terminal of the SCC-C6405(P).
1) CEILING MOUNT BRACKET
(SBR-100DCM)
This bracket is used for installing
the SmartDome CAMERA in the
plenum above the drop ceiling.
4. Adjust the switch below the Power Adapter to the proper voltage.
Then, connect the Power Adapter's plug to the Power Connector.
2) WALL MOUNT ADAPTOR
(SADT-100WM)
This adaptor is used for installing the
indoor housing or the outdoor
housing for the SmartDome Camera
on a wall.
5. Connect the Remote Control
Terminal of the
SCC-C6405(P)
and the external Controller.
Controller
Adapter BOARD
2-4
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
5) CEILING MOUNT ADAPTOR (SADT-100CM)
3) INDOOR HOUSING (SHG-120)
This adaptor is used for installing the indoor housing or the outdoor
housing for the SmartDome Camera to a concrete ceiling.
This housing is used for installing the SmartDome Camera to an indoor
wall or a ceiling.
E
6) POLE MOUNT ADAPTOR (SADT-100PM)
4) OUTDOOR HOUSING (SHG-220)
This adaptor is used for installing the WALL MOUNT ADAPTOR
(SADT-100WM) to a pole that is over 8 cm (2.76 in.) in diameter.
This housing is used for installing the SmartDome Camera to an
outdoor wall or a ceiling.
2-6
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Camera
5. [Figure 5] Match the
6. Pull the safety wire from the case
body, and assembly it to the
camera holder.
BRKT-ANCHOR and CAMERA
ADAPTER and use 4screws
(PH M4 x 8) to assemble them.
1. [Figure 1] Install the structure on the
ceiling.
(Refer to Installation reference
for the Length of the structure)
[Figure 5]
[Figure 6]
* Built in by the builder of the structure
E
[Figure 1]
Length of
ceiling Hole
2. Make a hole in the ceiling where the camera will be installed.
(The hole should be about
ø185)
3. [Figure 2] Assemble the
BRKT-ANCHOR on the ceiling
and screw the 4 bolts in.
[Figure 7]
7. [Figure 7] Match the 3 holes on the
back of the CAMERA and the
CONNECTOR and turn it left about
15 degrees.
(Check the sound of LOCKING
and that the LEVER-LOCKING
is in place)
* Use the screws (BH M3 x L8) to
connect the CAMERA and the
ADAPTER so they don't move.
[Figure 2]
4. [Figure 3,4] Connect the various cables to the CAMERA ADAPTER.
(See page 2-4)
[Figure 8]
8. [Figure 8] Assemble the
COVER-BODY onto the DOME.
[Figure 3]
[Figure 4]
2-8
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Structure of the Setup Menu
CAMERA SET
CAMERA ID
V-SYNC
ON.../OFF
INT/LINE...
Chapter 3 Setup Menu Overview
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
EXIT
COLOR/BW.../AUTO...
ON.../OFF
1/2/3/4
OFF/X2~X10
QUIT/SAVE/PRESET
In this chapter, we will look over the Setup Menu of the
SCC-C6405(P), First we'll look over the overall structure of the
Setup Menu, and then we'll look at the functions of each menu.
E
VIDEO SET
IRIS
ALC.../WDR...
SHUTTER
AGC
OFF/1/100(1/120)~1/1OK/AUTOX2~X160
OFF/LOW/HIGH
MOTION
WHITE BAL
DIS
S.SLOW/SLOW/NORM/FAST/F.FAST
ATW1/ATW2/AWC/MANU...
ON/OFF
FOCUS MODE
SPECIAL
AF/MF/ONEAF
...
REVERSE
DETAIL
OFF/H/V/H/V
(0)l---
EXIT
QUIT/SAVE/PRESET
PRESET
POSITION SET
PRESET ID
VIDEO SET
PRESET SPEED
DWELL TIME
IMAGE HOLD
EXIT
...
ON.../OFF
ON.../OFF
1~8
1~60S
ON/OFF
QUIT/SAVE/DEL
ZONE SET
AUTO SET
PRIVACY ZONE
ZONE DIR SET
ZONE AREA SET
EXIT
...
OFF/ON...
OFF/ON...
QUIT/SAVE
AUTO PAN
PATTERN
SCAN
AUTO PLAY
RET
1.../2.../3.../4...
1.../2.../3...
1.../2.../3.../4...
...
3-1
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
❈
If the power is turned off after PRESET, AUTO PAN, SCAN,
PATTERN function is activated and no other control is made, camera
will do the same function after the power is turned on.
ALARM SET
ALARM PRIORITY SET
ALARM IN SET
ALARM1 1~4
ALARM2 1~4
ALARM3 1~4
ALARM4 1~4
❈
Menu setting is available only when tilt position is under 90°.
When tilt position is over 90° and menu-on command is received,
pan will automatically rotate 180° and tilt will be move to the
corresponding position.
EXIT
QUIT/SAVE
ALARM1 NO/NC/OFF
ALARM2 NO/NC/OFF
ALARM3 NO/NC/OFF
ALARM4 NO/NC/OFF
Use the controller to press the MENU selection key and the following
screen will be displayed.
E
EXIT
QUIT/SAVE
* * MAIN MENU * *
ALARM OUT SET
ALARM1 1~3
ALARM2 1~3
ALARM3 1~3
ALARM4 1~3
MOTION 1~3
CAMERA SET...
VIDEO SET...
PRESET ...
0
5
1
6
2
7
3
8
4
9
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
✽ ✽ ✽ ✽
EXIT
QUIT/SAVE
AUTO SET
ALARM1 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4
ALARM2 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4
ALARM3 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4
ALARM4 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4
MOTION OFF/1~3/HALF1/HALF2/FULL/SCAN1~4
➁ PASSWORD
DEFINED
PASSWORD
UNDEFINED
➀
In case of , use UP/DOWN/LEFT/RIGHT/[ENTER] key for MENU
➀
EXIT
QUIT/SAVE
setup. In case of , type in the 4 digit password first. If correct, the
➁
MENU selection screen like
will be displayed and you will be able to
➀
AUX OUT CONTROL
RET
OUT1 ON/OFF
OUT2 ON/OFF
OUT3 ON/OFF
EXIT QUIT/SAVE
set up MENU by pressing UP/DOWN/LEFT/RIGHT/[ENTER] key.
1. CAMERA SET MENU
OTHER SET
PROPOTIONAL P/T
TURBO P/T
AUTO CAL
D-FLIP
CAM RESET
LANGUAGE
PASSWORD
EXIT
ON/OFF
ON/OFF
OFF/6H/12H/18H/24H
ON/OFF
...
CAMERA ID
The CAMERA ID menu assigns an ID to the SCC-C6405(P) to be displayed
on the connected monitor.On the CAMERA SET menu screen, select
CAMERA ID to ON and press [Enter]. You will see the sub screen for
deciding on the ID of the SCC-C6405(P). The Camera ID can have up to
20 alphanumeric characters, along with several special characters.
The assigned camera ID may be positioned to any desired location on the
screen by using the LOCATION submenu.
ON.../OFF
QUIT/SAVE
SYSTEM INFO
The diagram shown above illustrates the overall structure of the Setup Menu.
In this section, a description of the Setup menu features will enable users of the
SCC-C6405(P) to tailor it to their personal needs.
3-3
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
(CAMERA SET)
(CAMERA ID)
COLOR/BW
A B C D E F G H I J K L
M N O PQ R S T U V W X
Y Z 0 1 2 3 4 5 6 7 8 9
In the COLOR/BW menu, you can switch ON or OFF the IR (infrared) Filter.
In a poor illumination environment, the IR filter is turned off in the BW mode the its
sensitivity increases as high as a black and white camera. On the other hand, the
IR filter is turned on and the sensitivity decreases in the COLOR mode.
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
ON...
INT
COLOR
OFF
3
➜
Press
[Enter]
:
!
-
+
✽ ( ) /
SP ï î SP
LOCATION...
RET
OFF
COLOR
: The IR Filter is ON and the screen is normal.
EXIT
QUIT
SCC-C6405P........
BW
: The IR Filter is OFF and the screen is black and white.
(Sensitivity to low light is increased to a level comparable to a black
and white camera.)
* " ... " Means there are Sub Menus.
Select BW and press [ENTER] and the additional menu to select
BURST ON/OFF will appear.
E
V-SYNC
AUTO
: Select to automatically switch between the COLOR mode and BW
mode depending on the amount of light. In low light conditions, the
IR Filter is turned OFF and the sensitivity to low light is increased
by switching to the BW mode, but in bright light conditions, the IR
Filter is turned ON and the sensitivity is decreased by switching to
the COLOR mode.
In the V-SYNC menu, vertical synchronization can be selected. The
vertical synchronization signal supported by the SCC-C6405(P) is the INT
mode made by clock inside the SCC-C6405(P) and LINE mode adjusting
vertical synchronization to the exterior power frequency.
Select LINE and press [Enter]. You will see the LINE LOCK submenu
where you can adjust the phase of the LINE LOCK.
You can use the PHASE menu of the LINE LOCK submenu to assign as
much PHASE as you want.
Select AUTO and press [ENTER] and the additional menu to select
BW LEVEL and DURATION will appear.
- BURST ON : The color burst signal is output together with black and white
composite video signal.
- BURST OFF : The color burst signal is not output.
(CAMERA SET)
(LL-PHASE)
- LEVEL
: You can set the brightness level that changes from COLOR mode
to BW mode in 3 steps : LOW, MEDIUM, and HIGH.
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
LINE...
COLOR
OFF
3
➜
Press
[Enter]
- DURATION : Set the HOLDING time for switching between COLOR and BW
mode depending the changes in the amount of light. You can set
the HOLDING time to 10sec (S), 30sec, 60sec, or 300sec( L).
OFF
PHASE
RET
(000)----I ----
EXIT
QUIT
In AUTO mode, AGC will operates in high speed mode, and you cannot
change it manually, as it is indicated by "---".
(CAMERA SET)
(AUTO)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
AUTO...
OFF
0
➜
Press
[Enter]
BURST
LEVEL
DURATION
RET
ON
LOW
S --|---- L
0
EXIT
QUIT
Caution : If you use an infrared light source while in AUTO mode, AUTO
switching malfunction and camera AF malfunction may occur.
3-5
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTION DET
ZOOM SPEED
In the ZOOM SPEED menu you can select the speed of the ZOOM Key
(Tele/Wide).
Use the [Left] or [Right] keys in the ZOOM SPEED menu to select
the speed.
In MOTION DET, you can set the Motion Detection function, Motion Detection
Sensitivity, and the Area of Motion Detection. If the Motion Detection function
is set, the movement of an intruder can be detected. When motion is detected,
it sets off the Alarm signal of the Controller.
1 : Slowest speed
2 : Low speed
3 : High speed
4 : Fastest speed
(MOTION DET)
(CAMERA SET)
➜
Press
[Enter]
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
COLOR
ON...
3
E
OFF
AREA
PRESET...
SENSITIVITY L ---|--- H
RET
EXIT
QUIT
DIGITAL ZOOM
Select ON and press [ENTER] and the MOTION DET additional menu will
appear. The AREA menu, selecting the screen area where the MOTION
detection function will be applied may be selected by PRESET or USER.
Set AREA to PRESET and the MOTION detection function will be applied to
the factory default part.
If you set the AREA menu to USER and press [ENTER], you may vary the size
and position of the area where you want to apply the MOTION detection
function by yourself. Press Left, Right, Up, or Down to select an area size.
Press ENTER and then Left, Right, Up, or Down to select a position. Press
ENTER again to move back to the upper menu.
Use [ENTER] and Left, Right, Up, or Down to move and scale the MOTION
detection area.
Press [ENTER] again and you will escape the AREA setup menu.
Use SENSITIVITY to set up the sensitivity of MOTION detection strength.
The higher, the more sensitive.
You may set up the digital zoom magnification ratio in the DIGITAL ZOOM
menu. The magnification ratio ranges from OFF to 10. If you set Digital
Zoom of SCC-C6405(P) to max. 10 times, the mode will become the 22 time
optical zoom and you will be able to enlarge a subject by max. 220 times.
Use Left or Right to select a magnification ratio in the DIGITAL ZOOM menu.
(CAMERA SET)
(CAMERA SET)
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
BW...
OFF
3
CAMERA ID
V-SYNC
COLOR/BW
MOTION DET
ZOOM SPEED
DIGITAL ZOOM
OFF
INT
BW...
OFF
3
OFF
X10
EXIT
QUIT
EXIT
QUIT
SIZE
SIZE
➜
EXIT
Use the [Left,
Right, Up, Down]
Keys
The EXIT menu is used to quit the CAMERA SET menu of the
SCC-C6405(P) and return to the MAIN MENU.
- QUIT
: Ignores the changed information and restores the saved
information.
POSITION
POSITION
- SAVE : Saves the information of the setting condition of the menu.
- PRESET: Ignores the changed information and restores the initial
factory defaults of the menu.
After PAN/TILT movement finishes, MOTION DET function will not work
for about 5 seconds to stablize the chage of the screen.
* MOTION detection function operates based on the brightness change
within the setup region. Therefore, erroneous operation may occur
depending on the brightness difference between the background and
the object that is being taken, or the status of the area setup, etc.
3-7
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
- LEVEL 1 : Controls the shutter speed while WDR operates.
- LEVEL 2 : Controls the whole brightness while WDR operates.
- FLIKERLESS : This is for preventing flicker on the screen when NTSC
system is used in 50HZ power supply region and PAL system is used in
60HZ power supply region. That is to prevent shaking on the screen
resulted from the discordance of the vertical sync frequency and the
flicker frequency of the illumination. While this menu is ON, the
electronic shutter is fixed to 1/100sec (NTSC) or 1/120 sec (PAL).
2. VIDEO SET MENU
IRIS
There is a function to automatically adjust IRIS to the incoming light level.
Owing to this function, you may set up the brightness level yourself.
The ALC(Auto Light Control) menu allows you for video output level setup.
The WDR(Wide Dynamic Range) menu allows you to set up the WDR
level and the FLICKERLESS function.
ALC
SHUTTER
Choose the ALC of the IRIS item and press [ENTER] and set he submenu
to the Video Output level and BLC will be shown.The Video Output Level
can be set in the level item using the [Left, Right] keys.
E
You may designate both the fast electronic shutter speed and low
electronic shutter speed in the SHUTTER menu. The fast electronic
shutter supports 7 shutter speeds from 1/100(1/120) to 1/10K second to
be used for the bright and fast video image. The AUTO slow electronic
shutter supports 10 shutter speeds from x2 to x160 and sets the shutter
speed to be slow In order to make the image on the screen more distinct
and brighter when you photograph under dark illumination. If you want to
sense the light brightness to control the shutter speed to the brightness
automatically, select the AUTO slow shutter.
BLC (Submenu of the ALC menu)
With conventional cameras, strong background lighting interferes with the
clarity of objects, making them appear dark. In the SCC-C6405(P),
setting the BLC (Back Light Compensation), submenu of ALC/MANU
menu, will solve the problem of backlight and give you a clear screen.
Set the BLC menu to ON and the Backlight Compensation function will be
applied to the screen.
(VIDEO SET)
(VIDEO SET)
(ALC)
IRIS
SHUTTER
AGC
ALC...
OFF
OFF
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ALC...
OFF
OFF
ATW1
OFF
AF
➜
Press
[Enter]
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ATW1
OFF
AF
...
QUIT
BLC
OFF
LEVEL
RET
(0)----I ----
QUIT...
Keep pressing both Left and Right in the SHUTTER menu, the speed will
change in the following sequence.
OFF ➝ AUTO X2 ➝ AUTO X4 ➝ AUTO X6 ➝ AUTO X8 ➝ AUTO X12 ➝ AUTOX16
➝ AUTO X20 ➝ AUTO X40 ➝ AUTO X80 ➝ AUTO X160 ➝ OFF ➝ 1/100(1/120) ➝
1/250 ➝ 1/500 ➝ 1/1000 ➝ 1/2000 ➝ 1/4000 ➝ 1/10K ➝ OFF
WDR
The WDR camera is a state-of-art technology to expand the screen profit,
mostly effective when you photograph both indoor and outdoor. In short,
this function provides you with the distinct reproduction of not only the
indoor but also the outdoor. Press [ENTER] to set up the WDR level and
the FLICKERLESS function.
❈ In case the IRIS mode is set to WDR, only the following modes are
available.
(VIDEO SET)
(WDR)
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
WDR...
OFF
OFF
ATW1
ON
AF
➜
Press
[Enter]
OFF ➝ AUTO X2 ➝ AUTO X4 ➝ AUTO X6 ➝ AUTO X8 ➝ AUTO X12 ➝ AUTOX16
➝ AUTO X20 ➝ AUTO X40 ➝ AUTO X80 ➝ AUTO X160 ➝ OFF
LEVEL1
LEVEL2
FLICKERLESS
RET
L----I ----H
L----I ----H
OFF
QUIT...
3-9
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
AGC
WHITE BAL
The AGC menu was designed to provide you with brighter screen
supposed you photographed any subject in the dark resulting in less
brighter image than regulated. AGC menu setup is available only when
the SHUTTER menu is set to Fast Shutter or Off. Press either Left and
Right to go to LOW or HIGH and the AGC function will be activated. LOW
is use to lower the maximum AGC GAIN and HIGH raise the maximum
AGC GAIN.
Lights are generally denoted as color temperatures and expressed in
Kelvin (
K) units.
The general light color temperatures are shown below.
10000K
9000K
Blue sky
When the COLOR/BW menu of the camera set is set to AUTO, the AGC
menu item is left dotted and the maximum AGC GAIN is fixed to HIGH.
Rainy
E
(VIDEO SET)
8000K
7000K
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ALC...
OFF
LOW
ATW1
OFF
AF
Cloudy
...
QUIT
6000K
Partly Cloudy
Sunny
5000K
4000K
MOTION
The MOTION function is available only when the SHUTTER men is set to
Slow Shutter AUTO, being composed of 5 steps, S.SLOW, SLOW,
NORM, FAST, F.FAST.
Fluorescent lamp
G S.SLOW reduces the amount of AGC as much as possible to monitor
subjects with no immobility in the dark.
G SLOW reduces the amount of AGC to monitor subjects with little
immobility in the dark.
G NORM sets the amount of AGC to the middle to monitor mobile subjects
in the dark.
G FAST raises the amount of AGC to monitor fast subjects in the dark.
G F.FAST reduces the amount of AGC as much as possible to monitor
very fast subjects in the dark.
3000K
Halogen lamp
Candlelight
2000K
1000K
Tungsten lamp
When the SHUTTER menu is set to AUTO, press Down to locate the
cursor in the MOTION menu and press Left and Right for MOTION
function setup. Press Left to the SLOW side and Right to the FAST side.
(VIDEO SET)
IRIS
ALC...
AUTO x2
F.FAST
ATW1
OFF
SHUTTER
MOTION
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
AF
...
QUIT
3-11
3-12
Download from Www.Somanuals.com. All Manuals Search And Download.
You can select one of four modes for white balance adjustment as follows:
FOCUS MODE
In the FOCUS MODE MENU, the Focus method can be set to AF, MF, or ONEAF.
- ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the
color temperature is monitored continuously and thereby white balance is
set automatically. The following are the approximate supported color
temperature ranges in these modes.
- AF
: With AUTO FOCUS MODE, you can monitor the screen continuously
and it will focus automatically. While moving the zoom keys, it will
automatically focus so FOCUS key input is not necessary.
- MF
: In MANUAL FOCUS MODE the user adjusts the Focus manually.
ATW1 : 2500K ~ 9300K(✻1)
- ONEAF : The ONEAF Mode performs Auto-focusing only when the SCC-C6405(P)
stops after moving and when the SCC-C6405(P) is not moving it is same
as MF mode.
ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(✻2)
✻
✻
1. If the color temperature is out of this range in ATW1 mode, proper
white balance may not be obtained. In that case, select ATW2 mode.
2. In ATW2 mode, if one color is dominated in the shooted area, the
color can be displayed differently.
(The ONEAF Mode does not work when zooming out.
E
❈
When in the MF/ONEAF Mode, press the NEAR and FAR keys on the
Controller (SSC-1000/SSC-2000) at the same time to perform AUTO
FOCUS.)
Therefore, select the mode which is appropriate for the environment.
- AWC(Auto-Tracing White Balance Control): In this mode, accurate white
balance is obtained by pressing [ENTER] while having a white paper in
front of the camera. White Balance data will be maintained after set it
once. AWC mode is best in locations where the color temperature of light
source is constant.
Use the left/right keys to select AF, MF or ONEAF in the FOCUS MODE menu.
(VIDEO SET)
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the
white Balance considering the current illumination. Select MANU item
and press [ENTER], the sub screen where you can select Manual White
Balance will be shown. Use the left/right keys to select 3200K, 5600K or
OFF(USER) mode in the PRESET menu.
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ALC...
OFF
OFF
ATW1
OFF
AF
...
QUIT
- 3200
K
K
: Set color temperature to 3200
: Set color temperature to 5600
K
K
- 5600
- USER : Choose out a proper value from the RED and BLUE graph for
color and temperature setup.
SPECIAL
You may control REVERSE or DETAIL by yourself in the SPECIAL menu.
- REVERSE : Mirrors the screen horizontally, vertically, or in all directions.
(VIDEO SET)
(AWB/MANUAL)
- DETAIL
: Controls both horizontal and vertical distinction.
IRIS
SHUTTER
AGC
WHITE BAL
DIS
FOCUS MODE
SPECIAL
EXIT
ALC...
OFF
ON
MANU...
ON
AF
➜
Press
[Enter]
(VIDEO SET)
(SPECIAL)
PRESET
RET
3200K
IRIS
SHUTTER
AGC
WHITE BAL
DIS
ALC...
OFF
LOW
➜
Press
...
QUIT
ATW1
[Enter]
ON
REVERSE
DETAIL
RET
OFF
(0) -- I --
FOCUS MODE
SPECIAL
EXIT
AF
...
QUIT
DIS
The DIS(Digital Image Stabilization) function compensates the camera
screen shaking incurred from vibration.
It is recommended to deactivate the DIS function in the no vibration
environment.
EXIT
It's the same as the EXIT function of the CAMERA SET menu.
3-13
3-14
Download from Www.Somanuals.com. All Manuals Search And Download.
POSITION SET
From "POSITION SET..." press [ENTER] to get into the PAN/TILT,
FOCUS/ZOOM SET screen
to set the PAN/TILT location and FOCUS/ZOOM condition then press
[ENTER] to return to a higher menu.
3. PRESET
This is the menu that user sets the PAN/TILT location, Zoom/Focus, and
screen condition, so the camera can monitor the presetting area on
demand. A total of 128 presets are available.
Among the 128 PRESETS, PRESET 1: ALARM1, PRESET 2: ALARM2,
PRESET 3: ALARM3, PRESET 4: ALARM4,PRESET 5: set as special
preset corresponding MOTION.
PRESET ID
This is the ID set up function for each PRESET.
It can be set up to 12 characters using the left, right, up, and down keys.
The ID location can be set in the submenu of "LOCATION..."
E
VIDEO SET
This is the screen setting function for each PRESET.
Refer to the explanation under "VIDEO SET menu".
* * MAIN MENU * *
(PRESET MAP)
CAMERA SET...
VIDEO SET...
0
5
1
6
2
7
3
8
4
9
PRESET ...
➜
Press
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
PRESET SPEED
This function sets up the speed of PAN or TILT by 8 steps from 1(SLOW)
to 8(FAST).
- PRESET SPEED 1 : Maximum PAN moving speed of 240°/sec
- PRESET SPEED 8 : Maximum PAN moving speed of 400°/sec
[Enter]
30 31
î
ï
RET
ID:PRESET 0
DWELL TIME
This is a function setting for the DWELL TIME of the PRESET location in
"SCAN" motion. It can set DWELL TIME From 1 ~ 60 Sec.
PRESET NO.0
POSITION SET
PRESET ID
VIDEO SET
PRESET SPEED
DWELL TIME
IMAGE HOLD
...
➜
Press
[Enter]
ON...
OFF
8
3S
OFF
IMAGE HOLD
Pauses the image when PRESET is in movement, If you set the IMAGE
HOLD menu to ON, the screen will be paused until PRESET finishes
moving.
EXIT
QUIT
EXIT
"QUIT" : Does not save the selected information and returns to a higher
menu.
"SAVE" : Do saves the selected information and returns to a higher menu.
"DEL" : Deletes the selected information and restores the DEFAULT.
Then returns to a higher menu.
❈
❈
Set the PRESET position at the TILT which ranges from 0° to 90°. Beyond
this range, PRESET setup is not available.
When you try to set the Preset position by using the Controller(SCC-1000
or SCC-2000) beyound the range of TILT 90°, the text, “SET AGAIN” will
be displayed. In such a case, please retry in the area below TILT 90°.
3-15
3-16
Download from Www.Somanuals.com. All Manuals Search And Download.
BLANK ALL ABOVE
The available angle for setup ranges from OFF/0/-10 to -90 and the area
above a set angle will be regarded as the ZONE area.
4. ZONE SET
The ZONE SET menu includes the setup of PRIVACY ZONE, ZONE
DIRECTION, and ZONE AREA.
BLANK ALL BELOW
The available angle for setup ranges from OFF/0/-10 to -90 and the area
below a set angle will be regarded as the ZONE area.
* * MAIN MENU * *
(ZONE SET)
CAMERA SET...
VIDEO SET...
PRESET...
PRIVACY ZONE
ZONE DIR SET
...
ON...
➜
Press
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
ZONE AREA SET OFF
E
[Enter]
PRYVACY ZONE MAP
Press [ENTER] to enter the PRIVACY ZONE MAP screen from
EXIT
QUIT
“PRIVACY ZONE MAP ON..”.
Select a privacy zone number and press [ENTER] from the PRIVACY
ZONE MAP screen to enter the PRIVACY ZONE setup screen.
PRIVACY ZONE
Move PAN/TILT/ZOOM to select an area that can infringe someone
privacy, then this function will hide the area if it can be involved in the
photograph to protect his privacy. The number of area reaches up to 12.
(PRIVACY ZONE SET)
(PRIVACY ZONE MAP)
STYLE
BLANK ALL ABOVE OFF
BLAK ALL BELOW OFF
PRIVACY ZONE MAP ON...
MOSAIC
0
6
1
7
2
8
3
9
4
5
10 11
➜
Press
STYLE
[Enter]
In the STYLE menu, you may the shape of the PRIVACY ZONE area on the
screen.
RET
EXIT
QUIT
- MOSAIC1 : The privacy zone is displayed with the mosaic of 16 X 16 pixel.
- MOSAIC2 : The privacy zone is displayed with the mosaic of 32 X 32 pixel.
PRIVACY ZONE SET
0
SET ZONE AREA
SET ZOOM
REVERSE
ON...
...
ON
➜
Press
(PRIVACY ZONE SET)
STYLE
BLANK ALL ABOVE OFF
MOSAIC1
[Enter]
BLANK ALL BELOW
OFF
PRIVACY ZONE MAP ON...
EXIT
QUIT
EXIT
QUIT
❈
Set to the PRIVACY ZONE section, the mosaic screen will not be
3-17
3-18
Download from Www.Somanuals.com. All Manuals Search And Download.
SET ZONE AREA
SET ZOOM
Press [ENTER] at the “SET ZONE AREA...” position to enter the
PRIVACY ZONE setup screen. Control PAN/TILT/ZOOM to select 4
apexes of the PRIVACY ZONE area and the rectangular PRIVACY
ZONE area will be completed.
Press [ENTER] at the “SET ZOOM...” position to enter the ZOOM setup
screen. After ZOOM setup, the PRIVACY ZONE function will be in action
only at the higher magnification than the Zoom magnification
as set.
PRIVACY ZONE SET
0
PRIVACY ZONE SET
0
SET ZOOM
PRIVACY ZONE P/T 1
SET ZONE AREA
SET ZOOM
REVERSE
ON...
...
OFF
SET ZONE AREA
SET ZOOM
REVERSE
ON...
OFF
OFF
➜
After P/T/Z
control, press
[ENTER]
➜
Press
[Enter]
➜
Press
[Enter]
G
E
EXIT
QUIT
EXIT
QUIT
PRIVACY ZONE P/T 2
PRIVACY ZONE P/T 3
REVERSE
➜
After P/T/Z
control, press
[ENTER]
The REVERSE function applies PRIVACY MASK to the other area than
set as a privacy zone. ON/OFF is available.
G
G
PRIVACY ZONE SET
0
SET ZONE AREA
SET ZOOM
ON...
...
REVERSE
ON
PRIVACY ZONE P/T 4
➜
After P/T/Z
control, press
[ENTER]
EXIT
QUIT
G
EXIT
"QUIT" : Does not save the selected information and returns to a higher
menu.
"SAVE": Do saves the selected information and returns to a higher menu.
"DEL" : Deletes the selected information and restores the DEFAULT.
Then returns to a higher menu.
❈
❈
For the safer privacy protection, select about 10 % more than the
actual size to hide when you set up the PRIVACY ZONE area.
4 points of PRIVACY ZONE area are in the middle of the screen.
ZONE DIR SET/ZONE AREA SET
Therefore, when the tilt is positioned at upside limit(0° or 180°),
PRIVACY ZONE cannot be set in the area which is displayed
above center.
This function indicates the ID or direction depending on the set value
when PAN of SCC-C6405(P) is located in a specific area. If set to AREA,
it indicates the ID of the selected area and if set to N(NORTH), NE(NORTH-
EAST), E(EAST), SE(SOUTH-EAST), S(SOUTH), SW(SOUTH-WEST), W(WEST),
NW(NORTH-WEST.
❈
If the points becomes X shape, it means PRIVACY ZONE cannot
be set due to the size limitation.
3-19
3-20
Download from Www.Somanuals.com. All Manuals Search And Download.
ZONE DIR SET
LOCATION
Press the [Enter] key in the “ZONE DIR SET ON…” mode to enter the
NORTH SET screen. MAP. Move PAN to set the NORTH position and
press [ENTER]. Based on the North position,the direction of N(North),
NE(North-East), E(East), SE(South-East), S(South), SW(South-West),
W(West), NW(North-West) is displayed whenever you move PAN.
The “LOCATION...” menu designates the left/right LIMIT positions of
ZONE AREA. Enter the setup screen to move PAN, then select a start
position and press [ENTER]. Move PAN again
to select a end position and press [ENTER]. Now, ZONE AREA setup is
complete.
ZONE AREA SET
0
SET START!
(ZONE SET)
NORTH SET
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
PRIVACY ZONE
ZONE DIR SET
ZONE AREA SET
...
ON...
OFF
➜
After P/R/Z
control, press
[ENTER]
E
➜
Press
[Enter]
➜
Press
N
[Enter]
EXIT
QUIT
EXIT
QUIT
SET END!
ZONE AREA
Press [ENTER] to enter the ZONE AREA MAP screen from “ZONE
AREA SET...”. Select a ZONE AREA number from the ZONE AREA MAP
screen and press [ENTER] to enter the ZONE AREA setup screen.
After PAN control,
press [ENTER] to
finish.
(ZONE SET)
(ZONE AREA MAP)
PRIVACY ZONE
ZONE DIR SET
ZONE AREA SET
...
OFF
ON...
0
4
1
5
2
6
3
7
*
➜
Press
[Enter]
ZONE ID SET
This function is used to allocate as many as 12 IDs to each zone area.
Use Left , Right, UP, or DOWN for this purpose. You may select the ID
position from the additional menu of “LOCATION...”.
EXIT
QUIT
RET
ZONE AREA ID 0
ZONE AREA SET
0
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
A B C D E F G H I J K L
M N O P Q R S T U V W X
ZONE AREA SET
0
➜
Press
[Enter]
Y Z 0 1 2 3 4 5 6 7 8
✽ ( ) /
9
LOCATION
ZONE ID SET
ZONE ENABLE
...
...
ON
:
!
-
+
➜
Press
SP ï î SP
LOCATION...
RET
[Enter]
ZONE 0........
EXIT
QUIT
EXIT
QUIT
ZONE ENABLE
This function turns on or off the ZONE AREA ID indication.
3-21
3-22
Download from Www.Somanuals.com. All Manuals Search And Download.
DIRECTION
5. AUTO SET
This sets up the movement direction of the START to END location
(PAN location standard)
The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is
able to set up the AUTO PLAY motion.
"RIGHT " :
"LEFT " :
AUTO PAN
After selecting the locations of two points (PAN/TILT) of START and END,
it loops continuously in the set up SPEED. The number of AUTO PAN is
up to 4.
E
* * MAIN MENU * *
(AUTO SET)
CAMERA SET...
VIDEO SET...
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
ENDLESS
PRESET...
➜
Press
[Enter]
This is a 360-degree rotation function that stops for the DWELL TIME only in the
START and END positions without running between the START and END
positions. It can be set to "ON" or "OFF".
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
AUTO PLAY
RET
SPEED
This is a setting function for movement speed setup. It can be set from
STEP1 to STEP64.
AUTO PAN
1
START SET
END SET
...
...
DWELL TIME
➜
Press
DIRECTION
ENDLESS
SPEED
RIGHT
ON
32
This is a function for setting up the time to stay in the START to END position.
[Enter]
DWELL TIME
3S
PATTERN
EXIT
QUIT
This is a replay function so that the MANUAL functions such as PAN, TILT,
ZOOM, and FOCUS are played for 2 minutes.
START SET
From "START SET...", get into the START SET setup screen by pressing
[ENTER].
After selecting the locations of PAN/TILT location, press [ENTER] again to
return to higher menu.
❈
❈
When the PATTERN is saved/executed, the PAN/TILT is operated with
PROPORTIONAL ON, TURBO OFF.
Two minutes PATTERN function is supported only by the ALARM VER
1.100 over. If the SSC-1000 or SSC-2000 is used when
uploading/downloading the menu setup, reset the PATTERN because it
may be different with the first setting.
END SET
From "END SET...", get into the END SET setup screen by pressing
[ENTER]. Adjust PAN/TILT location and press [ENTER] to return to a
higher menu.
3-23
3-24
Download from Www.Somanuals.com. All Manuals Search And Download.
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET...
AUTO PLAY
(AUTO SET)
AUTO PLAY executes SCAN, AUTO PAN, PATTERN, and PRESET when there
is no camera action after AUTO RETURN finishes.
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
➜
Press
➜
Press
ZONE SET...
AUTO SET...
AUTO PLAY
[Enter]
[Enter]
ALARM SET...
OTHER SET...
SYSTEM INFO...
RET
(AUTO SET)
(AUTO PLAY SET)
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
AUTO RETURN 12H
PATTERN SET 1
PATTERN SET 1
AUTO PLAY
SCAN
➜
Press
[Enter]
➜
After PATTER
PLAY NUMBER
1
SET START POSITION
AND ENTER
AUTO PLAY
E
START
position setup,
press
RET
QUIT
[ENTER].
AUTO RETURN
This menu sets up the time during which AUTO PLAY repeats.
PATTERN can be set upto 3. Choose 1, 2, or 3 with the left or right key in the
"PATTERN SET" and press [ENTER] to get into the PATTERN set up screen. From
the moment "PATTERN 1 SET" is gone for 2 minutes, it memorizes the MANUAL
movements and after 2 minutes it will return to a higher menu. If you want to finish
set up before the 2-minutes ends, press [ENTER].
AUTO PLAY
This function sets up the motion which will be repeatedly performed by
SCC-C6405(P) whenever the time set by AUTO RETURN elapses. It covers
SCAN, AUTO PAN, PATTERN, and PRESET setup.
SCAN
PLAY NUMBER
This menu allocates a number to the motion set by AUTO PLAY. The numbers
range from 1 to 4 for SCAN AND AUTO PAN, 1 to 3 for PATTERN, and 0 to 127
for PRESET.
SCAN sets the direction of PRESET movement during “SCAN” operation. The
number of SCAN is up to 4 and each SCAN is able to allocate 32 PRESETs as a
maximum.
(SCAN MAP 1)
(AUTO SET)
0*S 1*
2
7
3
8
4
9
AUTO PAN
PATTERN
SCAN
1...
1...
1...
...
5
6
➜
Press
[Enter]
10 11 12 13 14
15 16 17 18 19
20 21 22 23 24
25 26 27 28 29
30 31
EXIT
AUTO PLAY
î
ï
SAVE
RET
If you enter the SCAN SET screen, PRESET MAP will be displayed. Move the
cursor to the number marked * where PRESET is saved and press [ENTER] and
S will appear and a PRESET will be included in SCAN.
3-25
3-26
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO SET
6. ALARM SET
This menu designates what to do at the time of ALARM input. Once an
alarm is given, the camera will shortly move to the PRESET position
corresponding to the respective alarm as follows.
PRESET1 to ALARM1
It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an
ALARM input from exterior SENSORs and it performs with PRESET or
PATTERN function and outputs the ALARM OUT signals.
PRESET2 to ALARM2
The Alarm will be recognized only when its input lasts more than 150ms
and the alarm operation time depends on the Preset Dwell time
corresponding to the alarm and whether AUTO is involved.
PRESET3 to ALARM3
PRESET4 to ALARM4
PRESET5 to MOTION
After DWELL TIME at a PRESET position, PATTERN or SCAN will be in
action according to the AUTO SET setup.
Setup of OFF/1/2/3/HALF1/HALF2/FULL/SCAN1~4 is available.
OFF dues not perform PATTERN or SCAN after moved to PRESET and
each menu has its own function as follows.
1 : PATTERN1,
2 : PATTERN2,
3 : PATTERN3,
HALF1 : Continuous operation of PATTERN1 + PATTERN2
HALF2 : Continuous operation of PATTERN2 + PATTERN3
FULL : Continuous operation of all the aboves
SCAN 1~4 : Scanning as set
E
* * MAIN MENU * *
( ALARM SET)
CAMERA SET...
ALARM PRIORITY SET ...
ALARM IN SET..
ALARM OUT SET..
AUTO SET..
VIDEO SET...
PRESET...
➜
Press
[Enter]
ZONE SET...
AUTO SET...
ALARM SET...
OTHER SET...
SYSTEM INFO...
AUX OUT CONTROL..
RET
ALARM PRIORITY SET
This sets the priority of the 4 ALARM inputs so ALARM can work
corresponding to the priority.
The priority of the DEFAULT is ALARM1: 1, ALARM2: 2, ALARM3: 3,
ALARM4: 4, MOTION: 5.
If the ALARM is working at the same time and the priority is the same, it
will operate according to the DEFAULT priority. While the ALARM is
working, it cannot detect MOTION.
AUX OUT CONTROL
This sets the ALARM OUT motion to continue or act only when the
ALARM is working.
If it is set to OFF the ALARM OUT motion will operate only when the
ALARM is working.
(Active "Low"), and if it's set to ON, the ALARM OUT will always operate
regardless of the ALARM.
ALARM IN SET
This sets the input TYPE to "NO" (Normal Open), "NC" (Normal Close), or
"OFF" depending on the features of the SENSOR connected.
7. OTHER SET
ALARM OUT SET
Each ALARM input corresponds to one of the 3 ALARM OUT.
PROPORTIONAL P/T
This function controls the PAN/TILT speed to the ZOOM magnification
ratio during the manual operation of PAN/TILT. If you set
PROPORTIONAL P/T to ON, the PAN/TILT speed will increase in the
ZOOM WIDE mode and decrease in the ZOON TELE mode even in the
same manual operation.
3-27
3-28
Download from Www.Somanuals.com. All Manuals Search And Download.
TURBO P/T
(PASSWORD)
(OTHER SET)
This function doubles up the speed of PAN/TILT movement by manual
operation of PAN/TILT. The speed may go up to 180°/sec(PAN).
PROPORTIONAL P/T ON
0
5
1
6
2
7
3
8
4
9
TURBO P/T
AUTO CAL.
D-FLIP
CAM RESET
LANGUAGE
PASSWORD
OFF
OFF
ON
➜
Press
[Enter]
...
✽ ✽ ✽ ✽
✽ ✽ ✽ ✽
AUTO CAL
ENGLISH
ON...
This function turns on or off Auto Calibration. SCC-C6405(P) has the Auto
Calibration function to improve the precision of LENS and PAN/TILT
motor. You may set to OFF/6H/12H/18H/24H. Without user’s key input for
the time designated by the user, A.C. will appear on the screen while
initializing LENS and PAN/TILT.
RET
EXIT
QUIT
Press UP/DOWN/LEFT/RIGHT key to locate the cursor on a number and
press [ENTER] for password setup. After you finish inputting the 4 digits
password and the 2nd row of the 4 digits PASSWORD input screen, input
the selected password again for reassurance.
E
D-FLIP
When D-FLIP is off, TILT movement ranges from 0° to 90°.
When D-FLIP is on, TILT movement ranges from 0° to 180°.
When D-FLIP is on, images mirror vertically and horizontally in the area
beyond TILT 90°.
If correct, the cursor will move to RET.
Press [ENTER] at RET, and the selected password will be saved,
returning to the OTHER SET screen.
Default password is 0123.
CAM RESET
CAM RESET clears all the settings made so far and restores the factory
default settings.
"CAMERA RESET?" message appears when you select CAM RESET.
Select "CANCEL" to return to the menu setup display or select OK to
restore the factory default settings.
8. SYSTEM INFO
This menu allows you to check S/W version, communication protocol,
baud rate, and address of SCC-C6405(P).
❈ Be careful when performing a CAM RESET operation, as it deletes all
( SYSTEM INFO)
* * MAIN MENU * *
CAMERA SET...
VIDEO SET...
PRESET...
setup values.
FPGA VER.
V1.000
ALARM VER. V1.000
MOTOR VER. V1.000
CAMERA VER. V1.000
EEPROM VER. V1.000
➜
Press
[Enter]
LANGUAGE
ZONE SET...
PROTOCOL
SAMSUNG
This function selects a language for MENU setup. Press UP/DOWN key to
choose English, French, German, Spanish, or Italian, and the selected
language will be applied to the full screen.
AUTO SET...
COMM. TYPE RS-485, HALF
BAUD RATE
ADDRESS
38400
0
ALARM SET...
OTHER SET...
SYSTEM INFO...
RET
PASSWORD
This function selects or cancels the MENU setup password. Press
[ENTER] at the state of PASSWORD ON, and the following screen will
appear for password setup.
3-29
3-30
Download from Www.Somanuals.com. All Manuals Search And Download.
9. SHORT KEYS
SSC-1000 or SSC-2000 Controller supports the following short keys.
*
SCC-C6405(P) has two FANs inside for preventing overheating.
If FAN doesn't work properly, messages below will be displayed.
In those case, replace the FAN.
Function
Key
-
CAMERA FAN ERROR !
: This message is displayed when the FAN which is connected with camera of
SCC-C6405(P) does not work properly.
CAMERA SET…
COLOR/BW
COLOR/BW
COLOR/BW
COLOR
BW
[PRESET] + [1] + [2] + [8] + [Enter]
[PRESET] + [1] + [2] + [9] + [Enter]
[PRESET] + [1] + [3] + [0] + [Enter]
AUTO
-
ALARM FAN ERROR !
: This message is displayed when the FAN which is located bottom of
SCC-C6405(P) does not work properly.
VIDEO SET…
IRIS
E
WDR
ALC
AF
[PRESET] + [1] + [3] + [1] + [Enter]
[PRESET] + [1] + [3] + [2] + [Enter]
[PRESET] + [1] + [3] + [3] + [Enter]
[PRESET] + [1] + [3] + [4] + [Enter]
[PRESET] + [1] + [3] + [5] + [Enter]
IRIS
FOCUS MODE
FOCUS MODE
FOUCS MODE
MF
ONEAF
ALARM SET…
AUX OUT CONTROL…
OUT1
OUT1
OUT2
OUT2
OUT3
OUT3
ON
[PRESET] + [1] + [3] + [6] + [Enter]
[PRESET] + [1] + [3] + [7] + [Enter]
[PRESET] + [1] + [3] + [8] + [Enter]
[PRESET] + [1] + [3] + [9] + [Enter]
[PRESET] + [1] + [4] + [0] + [Enter]
[PRESET] + [1] + [4] + [1] + [Enter]
OFF
ON
OFF
ON
OFF
OTHER SET…
PROPORTIONAL P/T
PROPORTIONAL P/T
TURBO P/T
ON
[PRESET] + [1] + [4] + [2] + [Enter]
[PRESET] + [1] + [4] + [3] + [Enter]
[PRESET] + [1] + [4] + [4] + [Enter]
[PRESET] + [1] + [4] + [5] + [Enter]
[PRESET] + [1] + [4] + [6] + [Enter]
[PRESET] + [1] + [4] + [7] + [Enter]
OFF
ON
TURBO P/T
OFF
ON
D-FLIP
D-FLIP
OFF
[PRESET] + [1] + [4] + [8] + [Enter]
[PRESET] + [1] + [4] + [9] + [Enter]
[PRESET] + [1] + [5] + [0] + [Enter]
AUTO RETURN *1)
AUTO CAL.
CAM RESET
Other keys than AUTO CAL. and AUTO RETURN, upon execution, shall
be applied to the MENU setup process.
*1) The use of AUTO RETURN will be available only when the function
equivalent to AUTO PLAY, a sub menu of AUTO SET has been built in.
3-31
3-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Product specifications
SCC-C6405
NO
1
Items
Contents
- Zoom lens single body WDR SmartDome CAMERA
- AC 24 10% (60Hz 0.3Hz)
- 18W
Remark
Product Type
2
Power Input
3
Power Consumption
Broadcasting Type
Image Device
4
- NTSC STANDARD COLOR SYSTEM
- 1/4 inch WDR compatible Exview HAD CCD
- 768(H) x 494(V)
5
6
Effective Pixels
Scanning Mode
7
- 525 Lines, 2:1 Interlace
E
- Horizontal : 15, 734 Hz(INT) / 15, 750 Hz(L/L)
- Vertical : 59, 94 Hz(INT) / 60 Hz(L/L)
8
Scanning line Frequency
- INT/LINE LOCK
- 480 TV LINES
- 50dB (AGC OFF)
9
Synchronization Mode
Resolution
10
11
S/N Ratio
- COLOR : 0.2 Lux (SENS UP X4)
0.005 Lux (SENS UP X160)
12
13
Min. Object Illumination
WDR
- B/W
: 0.07 Lux (SENS UP X4)
0.002 Lux (SENS UP X160)
- 128
- ATW1/ATW2/AWC/MANUAL MODE
(3200K, 5600K, R/B GAIN Court)
Color Temperature
Signal Output
14
15
- COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC
- one body; 22x Zoom lens
- Focal length : 3.6 to 79.2 mm
- Aperture : F1.6(Wide), F3.8(Tele)
- Auto Focus
Lens
16
- PAN range : 360° Endless
- Preset Pan Speed : 400° /sec, maximum
- Manual Pan Speed : 0.1° ~ 180° /sec (64Step)
17
18
19
PAN Function
- TILT range : 0° ~ 180°
- Preset Tilt Speed : 200° /sec, maximum
- Manual Tilt Speed : 0.1° ~ 90° /sec (64Step)
TILT Function
- Tele/Wide(ZOOM), Near/Far(FOCUS),
Iris Open/Close, Pan/Tilt, MENU
REMOTE CONTROL
RS-485 HALF/FULL Duplex, RS-422
- Alarm Inputs : 4 IN(5mA Sink)
- Alarm Outputs : 3 OUT (Open collector : 2
DC24V 40mA Max, Relay : 1, NO, NC, COM
2A 30VDC, 0.5A 125VAC Max)
20
ALARM
- -10°C ~ +50°C
Operation Temperature
Operation Humidity
21
22
- ~90%
- DOME : 147 (ø),
- Outline : 159.6(ø) x 177(H)
23
24
SIZE
- 1.7Kg
Weight
One Year(for
use of Full AF)
- Lens
Rotated
10,000,000
Times
Lives of Main Parts
- Slip-ring
- Fan
25
4.5 Years
3-33
3-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Cautions
SCC-C6405P
NO
1
Items
Contents
- Zoom lens single body WDR SmartDome CAMERA
- AC 24 10% (50Hz 0.3Hz)
- 18W
Remark
Product Type
Power Input
• The copyright of the manual belongs to Samsung Electronics Co., Ltd.
2
•
Without the permission of Samsung Electronics it cannot be reproduced
electronically, mechanically, audibly, or by any other method.
3
Power Consumption
Broadcasting Type
Image Device
4
- PAL STANDARD COLOR SYSTEM
- 1/4 inch WDR compatible Exview HAD CCD
- 752(H) x 582(V)
5
•
This manual will be modified according to product enhancements.
6
Effective Pixels
Scanning Mode
7
- 625 Lines, 2:1 Interlace
E
- Horizontal : 15, 625Hz(INT) / 15, 625 Hz(L/L)
- Vertical : 50 Hz(INT) / 50 Hz(L/L)
8
Scanning line Frequency
- INT/LINE LOCK
- 480 TV LINES
- 50dB (AGC OFF)
9
Synchronization Mode
Resolution
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
10
11
S/N Ratio
- COLOR : 0.2 Lux (SENS UP X4)
0.005 Lux (SENS UP X160)
(Applicable in the European Union and other European countries with
separate collection systems)
12
13
Min. Object Illumination
WDR
- B/W
: 0.07 Lux (SENS UP X4)
0.002 Lux (SENS UP X160)
- 128
This marking shown on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly
to promote the sustainable reuse of material resources.
- ATW1/ATW2/AWC/MANUAL MODE
(3200K, 5600K, R/B GAIN Court)
Color Temperature
Signal Output
14
15
- COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC
- one body; 22x Zoom lens
- Focal length : 3.6 to 79.2 mm
- Aperture : F1.6(Wide), F3.8(Tele)
- Auto Focus
Lens
16
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they can take
this item for environmentally safe recycling.
- PAN range : 360° Endless
- Preset Pan Speed : 400° /sec, maximum
- Manual Pan Speed : 0.1° ~ 180° /sec (64Step)
17
18
19
PAN Function
- TILT range : 0° ~ 180°
- Preset Tilt Speed : 200° /sec, maximum
- Manual Tilt Speed : 0.1° ~ 90° /sec (64Step)
TILT Function
Business users should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
- Tele/Wide(ZOOM), Near/Far(FOCUS),
Iris Open/Close, Pan/Tilt, MENU
RS-485 HALF/FULL Duplex, RS-422
REMOTE CONTROL
- Alarm Inputs : 4 IN(5mA Sink)
- Alarm Outputs : 3 OUT (Open collector : 2
DC24V 40mA Max, Relay : 1, NO, NC, COM
2A 30VDC, 0.5A 125VAC Max)
20
ALARM
- -10°C ~ +50°C
Operation Temperature
Operation Humidity
21
22
- ~90%
- DOME : 147 (ø),
- Outline : 159.6(ø) x 177(H)
23
24
SIZE
- 1.7Kg
Weight
One Year(for
use of Full AF)
- Lens
Rotated
10,000,000
Times
Lives of Main Parts
- Slip-ring
- Fan
25
4.5 Years
3-35
3-36
Download from Www.Somanuals.com. All Manuals Search And Download.
|