SCX-4725F
SCX-4725FN
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2006 Samsung Electronics Co., Ltd. All rights reserved.
This manual is provided for information purposes only. All information included herein is subject to change without notice. Samsung Electronics is not
responsible for any direct or indirect damages, arising from or related to use of this manual.
• SCX-4725F and SCX-4725FN are model names of Samsung Electronics Co., Ltd.
• Samsung and Samsung logo are trademarks of Samsung Electronics Co., Ltd.
• Centronics is a trademark of Centronics Data Computer Corporation.
• PCL and PCL 6 are trademarks of Hewlett-Packard company.
• Microsoft, Windows, Windows 98, Windows Me, Windows 2000, Windows XP(32/64bit), and Windows 2003(32/64bit) are registered trademarks of
Microsoft Corporation.
• PostScript 3 is a trademark of Adobe System, Inc.
• UFST® and MicroType™ are registered trademarks of Monotype Imaging Inc.
• TrueType, LaserWriter and Macintosh are trademarks of Apple Computer, Inc.
• All other brand or product names are trademarks of their respective companies or organizations.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTACT SAMSUNG WORLDWIDE
If you have any comments or questions regarding Samsung products,
Country
Customer Care Center
Web Site
contact the Samsung customer care center.
LITHUANIA
LUXEMBURG
MALAYSIA
8-800-77777
www.samsung.com/lt
www.samsung.com/be
www.samsung.com/my
Country
ARGENTINE
AUSTRALIA
AUSTRIA
BELGIUM
Customer Care Center
Web Site
0035 (0)2 261 03 710
1800-88-9999
0800-333-3733
www.samsung.com/ar
www.samsung.com/au
www.samsung.com/at
www.samsung.com/be
www.samsung.com/br
1300 362 603
MEXICO
01-800-SAMSUNG (7267864) www.samsung.com/mx
0800-SAMSUNG (726-7864)
0032 (0)2 201 24 18
NETHERLANDS
NEW ZEALAND
NORWAY
0900 20 200 88 (€ 0,10/min)
0800SAMSUNG(726-7864)
815-56 480
www.samsung.com/nl
www.samsung.com/nz
www.samsung.com/no
www.samsung.com/latin
www.samsung.com/ph
BRAZIL
0800-124-421
4004-0000
PANAMA
800-7267
CANADA
CHILE
1-800-SAMSUNG (7267864)
800-726-7864 (SAMSUNG)
www.samsung.com/ca
www.samsung.com/cl
www.samsung.com.cn
PHILIPPINES
1800-10-SAMSUNG
(7267864)
CHINA
800-810-5858
POLAND
0 801 801 881
022-607-93-33
www.samsung.com/pl
010- 6475 1880
COLOMBIA
01-8000-112-112
0-800-507-7267
844 000 844
www.samsung.com/co
www.samsung.com/latin
www.samsung.com/cz
PORTUGAL
80 8 200 128
www.samsung.com/pt
www.samsung.com/latin
www.samsung.com/latin
COSTA RICA
PUERTO RICO
1-800-682-3180
1-800-751-2676
CZECH
REPUBLIC
REP.
DOMINICA
Distributor pro Českou republiku : Samsung Zrt., česka
organizační složka Vyskočilova 4, 14000 Praha 4
REPUBLIC OF
IRELAND
0818 717 100
www.samsung.com/uk
DENMARK
ECUADOR
EL SALVADOR
ESTONIA
70 70 19 70
www.samsung.com/dk
www.samsung.com/latin
www.samsung.com/latin
www.samsung.ee
1-800-10-7267
800-6225
RUSSIA
8-800-555-55-55
www.samsung.ru
SINGAPORE
SLOVAKIA
1800-SAMSUNG (7267864)
0800-SAMSUNG (726786)
0860 726 7864 (SAMSUNG)
www.samsung.com/sg
www.samsung.com/sk
www.samsung.com/za
800-7267
KAZAHSTAN
8-10-800-500-55-500
www.samsung.kz
SOUTH
AFRICA
KYRGYZSTAN 00-800-500-55-500
SPAIN
902 10 11 30
0771-400 200
0800-7267864
0800-329-999
www.samsung.com/es
www.samsung.com/se
www.samsung.com/ch/
www.samsung.com/tw
www.samsung.com/th
FINLAND
FRANCE
030-6227 515
www.samsung.com/fi
www.samsung.com/fr
SWEDEN
SWITZERLAND
TAIWAN
3260 SAMSUNG or
08 25 08 65 65 (€ 0,15/min)
GERMANY
01805 - 121213
(€ 0,14/min)
www.samsung.de
THAILAND
1800-29-3232
02-689-3232
GUATEMALA
HONG KONG
HUNGARY
INDIA
1-800-299-0013
www.samsung.com/latin
www.samsung.com/hk
www.samsung.com/hu
www.samsung.com/in/
3698 4698
TRINIDAD &
TOBAGO
1-800-7267-864
www.samsung.com/latin
06-80-SAMSUNG (7267864)
3030 8282
TURKEY
U.A.E
444 77 11
www.samsung.com.tr
www.samsung.com/mea
www.samsung.com/uk
www.samsung.com
1800 110011
800-SAMSUNG (7267864)
0870 SAMSUNG (7267864)
1-800-SAMSUNG (7267864)
8-800-502-0000
INDONESIA
ITALIA
0800-112-8888
www.samsung.com/id
www.samsung.com/it
U.K
800-SAMSUNG(7267864)
800-048989
U.S.A.
UKRAINE
UZBEKISTAN
VENEZUELA
VIETNAM
www.samsung.ua
JAMAICA
JAPAN
1-800-234-7267
0120-327-527
800-7267
www.samsung.com/latin
www.samsung.com/jp
8-800-120-0400
www.samsung.com.uz
www.samsung.com/latin
www.samsung.com/vn
0-800-100-5303
LATVIA
www.samsung.com/lv/
index.htm
1 800 588 889
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Special features ...................................................................................................................................................... 1.1
Printer overview ...................................................................................................................................................... 1.2
Finding more information ........................................................................................................................................ 1.4
Menu overview ........................................................................................................................................................ 2.1
Setting the date and time ........................................................................................................................................ 2.2
Setting sounds ........................................................................................................................................................ 2.2
System requirements .............................................................................................................................................. 3.2
Introduction ............................................................................................................................................................. 4.1
Supported operating systems ................................................................................................................................. 4.1
Configuring TCP/IP ................................................................................................................................................. 4.1
Configuring EtherTalk ............................................................................................................................................. 4.2
Using SetIP program................................................................................................................................................ 4.2
Loading paper ......................................................................................................................................................... 5.5
Copying ................................................................................................................................................................... 6.1
Using special copy features .................................................................................................................................... 6.2
Printing a document ................................................................................................................................................ 7.1
Canceling a print job ............................................................................................................................................... 7.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanning to an application ...................................................................................................................................... 8.1
Setting the fax header ............................................................................................................................................. 9.1
Adjusting the document settings ............................................................................................................................. 9.1
Sending a fax automatically .................................................................................................................................... 9.2
Redialing the last number ....................................................................................................................................... 9.3
Receiving automatically in Fax mode ..................................................................................................................... 9.3
Receiving manually in Tel mode ............................................................................................................................. 9.3
Receiving manually using an extension telephone ................................................................................................. 9.4
Receiving automatically in Ans/Fax mode .............................................................................................................. 9.4
Receiving faxes using DRPD mode ........................................................................................................................ 9.4
Receiving in secure receiving mode ....................................................................................................................... 9.4
Sending a priority fax .............................................................................................................................................. 9.7
Printing sent fax report automatically .................................................................................................................... 10.2
Setting up Phone Book ......................................................................................................................................... 10.3
How to purchase ................................................................................................................................................... 11.1
Cleaning your machine ......................................................................................................................................... 12.2
Clearing the Toner Empty Replace Toner message ............................................................................................. 12.6
(SCX-4725FN only) ............................................................................................................................................. 12.7
Clearing document jams ....................................................................................................................................... 13.1
Understanding display messages ......................................................................................................................... 13.3
Toner cartridge-related messages ................................................................................................................. 13.5
Solving other problems ......................................................................................................................................... 13.5
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner and copier specifications ........................................................................................................................ 14.2
Facsimile specifications ........................................................................................................................................ 14.2
Download from Www.Somanuals.com. All Manuals Search And Download.
17 The Power cord supplied with your machine should be used for safe operation. If
you are using a cord which is longer than 2 m with 110 V machine, then it should
Important Precautions and Safety Information
When using this machine, these basic safety precautions should always be followed to
reduce risk of fire, electric shock and injury to people:
be 16 AWG1 or bigger.
18 Use only No.26 AWG* or larger telephone line cord.
19 SAVE THESE INSTRUCTIONS.
1
2
3
Read and understand all instructions.
Use common sense whenever operating electrical appliances.
Follow all warnings and instructions marked on the machine and in the literature
accompanying the machine.
Laser Safety Statement
4
If an operating instruction appears to conflict with safety information, heed the
safety information. You may have misunderstood the operating instruction. If you
cannot resolve the conflict, contact your sales or service representative for
assistance.
The printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR,
chapter 1 Subchapter J for Class I(1) laser products, and elsewhere is certified as a
Class I laser product conforming to the requirements of IEC 825.
Class I laser products are not considered to be hazardous. The laser system and printer
are designed so there is never any human access to laser radiation above a Class I level
during normal operation, user maintenance or prescribed service condition.
5
Unplug the machine from the AC wall socket and/or telephone jack before
cleaning. Do not use liquid or aerosol cleaners. Use only a damp cloth for
cleaning.
WARNING
Never operate or service the printer with the protective cover removed from Laser/
Scanner assembly. The reflected beam, although invisible, can damage your eyes.
6
7
8
9
Do not place the machine on an unstable cart, stand or table. It may fall, causing
serious damage.
When using this product, these basic safety precautions should always be followed to
reduce risk of fire, electric shock, and injury to persons:
Your machine should never be placed on, near or over a radiator, heater, air
conditioner or ventilation duct.
Do not allow anything to rest on the power. Do not locate your machine where the
cords will be abused by persons walking on them.
Do not overload wall outlets and extension cords. This can diminish performance,
and may result in the risk of fire or electric shock.
10 Do not allow pets to chew on the AC power, telephone or PC interface cords.
11 Never push objects of any kind into the machine through case or cabinet
openings. They may touch dangerous voltage points, creating a risk of fire or
shock. Never spill liquid of any kind onto or into the machine.
12 Your machine may have a heavy cover for optimal pressure on the document for
the best scanning and/or faxing (usually the flatbed-type machine). In this case,
replace the cover after placing document on the scan glass, by holding and
moving it down slowly until it seats on its location.
13 To reduce the risk of electric shock, do not disassemble the machine. Take it to a
qualified service technician when repair work is required. Opening or removing
covers may expose you to dangerous voltages or other risks. Incorrect reassembly
could cause electric shock when the unit is subsequently used.
14 Unplug the machine from the telephone jack, PC and AC wall outlet and refer
servicing to qualified service personnel under the following conditions:
• When any part of the power cord, plug or connecting cable is damaged or frayed.
• If liquid has been spilled into the machine.
Ozone Safety
• If the machine has been exposed to rain or water.
During normal operation, this machine produces ozone. The ozone
produced does not present a hazard to the operator. However, it is
advisable that the machine be operated in a well ventilated area.
• If the machine does not operate properly after instructions have been followed.
• If the machine has been dropped, or the cabinet appears damaged.
• If the machine exhibits a sudden and distinct change in performance.
If you need additional information about ozone, please request your
nearest Samsung dealer.
15 Adjust only those controls covered by the operating instructions. Improper
adjustment of other controls may result in damage, and may require extensive
work by a qualified service technician to restore the machine to normal operation.
16 Avoid using this machine during a lightning storm. There may be a remote risk of
electric shock from lightning. If possible, unplug the AC power and telephone cord
for the duration of the lightning storm.
1 AWG: American Wire Gauge
i
Download from Www.Somanuals.com. All Manuals Search And Download.
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Mercury Safety
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE
RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR
FEDERAL LAWS. For details see lamprecycle.org, eiae.org, or call 1-800-
Samsung
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Power Saver
• Consult the dealer or experienced radio TV technician for help.
This printer contains advanced energy conservation technology that reduces power
consumption when it is not in active use.
CAUTION: Change or modifications not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate the equipment.
When the printer does not receive data for an extended period of time, power
consumption is automatically lowered.
Canadian Radio Interference Regulations
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled
“Digital Apparatus”, ICES-003 of the Industry and Science Canada.
Recycling
Please recycle or dispose of the packaging material for this product
in an environmentally responsible manner.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur:
“Appareils Numériques”, ICES-003 édictée par l’Industrie et Sciences Canada.
Fax Branding
Correct Disposal of This Product (Waste Electrical &
Electronic Equipment)
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to
use a computer or other electronic device to send any message via a telephone
facsimile machine unless such message clearly contains in a margin at the top or bottom
of each transmitted page or on the first page of the transmission the following
information:
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its
working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from
other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources.
(1) the date and time of transmission
(2) identification of either business, business entity or individual sending the message;
and
(3) telephone number of either the sending machine, business, business entity or
individual.
The Telephone Company may make changes in its communications facilities,
equipment operations or procedures where such action is reasonably required in the
operation of its business and is not inconsistent with the rules and regulations in FCC
Part 68. If such changes can be reasonably expected to render any customer terminal
equipment incompatible with telephone company communications facilities, or require
modification or alteration of such terminal equipment, or otherwise materially affect its
use or performance, the customer shall be given adequate notice in writing, to allow the
customer an opportunity to maintain uninterrupted service.
Household users should contact either the retailer where they purchased this product,
or their local government office, for details of where and how they can take this item for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product should not be mixed with other commercial wastes for
disposal.
Radio Frequency Emissions
FCC Information to the User
Ringer Equivalence Number
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
The Ringer Equivalence Number and FCC Registration Number for this machine may
be found on the label located on the bottom or rear of the machine. In some instances
you may need to provide these numbers to the telephone company.
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that
may cause undesired operation.
The Ringer Equivalence Number (REN) is a measure of the electrical load placed on the
telephone line, and is useful for determining whether you have “overloaded” the line.
Installing several types of equipment on the same telephone line may result in problems
making and receiving telephone calls, especially ringing when your line is called. The
sum of all Ringer Equivalence Numbers of the equipment on your telephone line should
be less than five in order to assure proper service from the telephone company. In some
cases, a sum of five may not be usable on your line. If any of your telephone equipment
is not operating properly, you should immediately remove it from your telephone line, as
it may cause harm to the telephone network.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING:
EC Certification
FCC Regulations state that changes or modifications to this equipment not expressly
approved by the manufacturer could void the user’s authority to operate this equipment.
In the event that terminal equipment causes harm to the telephone network, the
telephone company should notify the customer that service may be stopped. However,
where prior notice is impractical, the company may temporarily cease service, providing
that they:
Certification to 1999/5/EC Radio Equipment & Telecommunications
Terminal Equipment Directive (FAX)
This Samsung product has been self-certified by Samsung for pan-European single
terminal connection to the analogue public switched telephone network (PSTN) in
accordance with Directive 1999/5/EC. The product has been designed to work with the
national PSTNs and compatible PBXs of the European countries:
a) promptly notify the customer.
In the event of problems, you should contact the Euro QA Lab of Samsung Electronics
Co., Ltd. in the first instance.
b) give the customer an opportunity to correct the equipment problem.
c) inform the customer of the right to bring a complaint to the Federal Communication
Commission pursuant to procedures set out in FCC Rules and Regulations Subpart E
of Part 68.
The product has been tested against TS103 021. To assist in the use and application of
terminal equipment which complies with this standard, the European
Telecommunication Standards Institute (ETSI) has issued an advisory document (EG
201 121) which contains notes and additional requirements to ensure network
compatibility of TS103 021 terminals. The product has been designed against, and is
fully compliant with, all of the relevant advisory notes contained in this document.
You should also know that:
• Your machine is not designed to be connected to a digital PBX system.
• If you intend to use a computer modem or fax modem on the same phone line as
your machine, you may experience transmission and reception problems with all the
equipment. It is recommended that no other equipment, except for a regular
telephone, share the line with your machine.
Replacing the Fitted Plug (for UK Only)
• If your area experiences a high incidence of lightning or power surges, we
recommend that you install surge protectors for both the power and the telephone
lines. Surge protectors can be purchased from your dealer or telephone and
electronic specialty stores.
IMPORTANT
The mains lead for this machine is fitted with a standard (BS 1363) 13 amp plug and has
a 13 amp fuse. When you change or examine the fuse, you must re-fit the correct 13
amp fuse. You then need to replace the fuse cover. If you have lost the fuse cover, do
not use the plug until you have another fuse cover.
• When programming emergency numbers and/or making test calls to emergency
numbers, use a non-emergency number to advise the emergency service dispatcher
of your intentions. The dispatcher will give you further instructions on how to actually
test the emergency number.
Please contact the people from you purchased the machine.
The 13 amp plug is the most widely used type in the UK and should be suitable.
However, some buildings (mainly old ones) do not have normal 13 amp plug sockets.
You need to buy a suitable plug adaptor. Do not remove the moulded plug.
• This machine may not be used on coin service or party lines.
• This machine provides magnetic coupling to hearing aids.
WARNING
• You may safely connect this equipment to the telephone network by means of a
standard modular jack, USOC RJ-11C.
If you cut off the moulded plug, get rid of it straight away.
You cannot rewire the plug and you may receive an electric shock if you plug it
into a socket.
Declaration of Conformity (European Countries)
IMPORTANT WARNING: You must earth this machine.
Approvals and Certifications
The wires in the mains lead have the following color code:
The CE marking applied to this product symbolizes Samsung
Electronics Co., Ltd. Declaration of Conformity with the following
applicable 93/68/EEC Directives of the European Union as of the
dates indicated:
• Green and Yellow:
• Blue:
Earth
Neutral
Live
• Brown:
If the wires in the mains lead do not match the colors marked in your plug, do the
following:
January 1, 1995: Council Directive 73/23/EEC Approximation of the laws of the
member states related to low voltage equipment.
You must connect the green and yellow wire to the pin marked by the letter “E” or by the
safety ‘Earth symbol’ or colored green and yellow or green.
January 1, 1996: Council Directive 89/336/EEC (92/31/EEC), approximation of the laws
of the Member States related to electromagnetic compatibility.
You must connect the blue wire to the pin which is marked with the letter “N” or colored
black.
March 9, 1999: Council Directive 1999/5/EC on radio equipment and
telecommunications terminal equipment and the mutual recognition of their conformity.
You must connect the brown wire to the pin which is marked with the letter “L” or colored
red.
A full declaration, defining the relevant Directives and referenced standards can be
obtained from your Samsung Electronics Co., Ltd. representative.
You must have a 13 amp fuse in the plug, adaptor, or at the distribution board.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Print in various environments
1 Introduction
• You can print with Windows 98/Me/2000/XP(32/64bit)/
2003(32/64bit).
Thank you for purchasing this Samsung multifunctional product. Your
machine provides printing, copying, scanning, and faxing functions.
• Your machine is compatible with a variety of Linux systems.
• Your machine is compatible with a variety of Macintosh systems
This chapter includes:
(SCX-4725FN only).
• Zoran IPS Emulation* compatible with PostScript 3 (PS) enables PS
printing (SCX-4725FN only).
•
•
•
•
* Zoran IPS Emulation compatible with PostScript 3
• © Copyright 1995-2005, Zoran Corporation. All
rights reserved. Zoran, the Zoran logo, IPS/PS3, and
OneImage are trademarks of Zoran Corporation.
* 136 PS3 fonts
Contains UFST and MicroType from Monotype Imaging Inc.
Special features
Your new machine is equipped with special features that improve print
quality. You can:
Machine features
The table below lists a general overview of features supported by your
machine.
Print with excellent quality and speed
• You can print with a resolution of up to 1200 dpi [Best].
See the Software Section.
• Your machine prints A4-sized paper at up to 24 ppm
and letter-sized paper at up to 24 ppm.
(I: Installed, NA: Not Available)
1
Features
IEEE 1284 Parallel
SCX-4725F
SCX-4725FN
NA
I
NA
USB 2.0
I
I
I
Handle paper flexibly
PostScript Emulation
NA
NA
• The manual tray supports letterhead, envelopes,
Network Interface
labels, transparencies, custom-sized media, postcards,
and heavy paper. The manual tray holds 1 sheet of
paper.
250
(Ethernet 10/100 Base TX)
1
Duplex Printing
NA
NA
NA
I
• The 250-sheet tray supports plain paper in various
sizes.
Macintosh Driver
Create professional documents
1. Printing on both sides of paper.
• Print Watermarks. You can customize your documents
with words, such as “Confidential”. See the Software
Section.
• Print Posters. The text and pictures of each page of
your document are magnified and printed across the
sheet of paper and can then be taped together to form
a poster. See the Software Section.
Save time and money
• You can print multiple pages on one single sheet of paper to save
paper.
• You can use preprinted forms and letterhead with plain paper. See the
Software Section.
• This machine automatically conserves electricity by substantially
reducing power consumption when not in use.
1. pages per minute
1.1
<Introduction>
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer overview
These are the main components of your machine:
Front view
Rear view
* The figure above shows an SCX-4725FN.
* The figure above shows an SCX-4725FN.
1
8
1
5
ADF (automatic
document feeder)
front cover
rear cover
telephone line socket
(LINE)
1
1
2
3
4
5
6
7
9
2
3
4
6
document width guides
document input tray
scanner lid
tray
power switch
network port
10
11
12
13
14
7
output support
scanner glass
manual tray
toner cartridge
power receptacle
USB port
extension telephone
socket (EXT)
document output tray
control panel
1. SCX-4725FN only.
output tray
manual tray paper width
guides
1. Automatic document feeder is used as ADF in this user’s guide.
1.2
<Introduction>
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel overview
1
2
11
12
Darkness: Adjusts the document brightness for the current copy
job.
Start: Starts a job.
No. of Copies: Enters the number of copies.
Stop/Clear: Stops an operation at any time. In Standby mode,
clears/cancels the copy options, such as the darkness, the
document type setting, the copy size, and the number of copies.
3
13
Original Type: Selects the document type for the current copy job.
Number keypad: Dials a number or enters alphanumeric
characters.
4
5
14
15
Reduce/Enlarge: Makes a copy smaller or larger than the original.
Resolution: Adjusts the document resolution for the current fax job.
Favorite Copy: Allows you to use one of the special copy features,
such as Clone, Copy Collate, Autofit, ID Card Copy, 2/4 Up and
Poster.
Broadcasting: Allows you to send a fax to multiple destinations.
6
7
16
17
Display: Shows the current status and prompts during an operation.
Phone Book: Allows you to store frequently used fax numbers in
memory or search for stored fax numbers. Also allows you to print a
Phone Book list.
Scroll buttons: Scroll through the options available in the selected
Redial/Pause: In Standby mode, redials the last number, or in Edit
menu, and increase or decrease values.
mode, inserts a pause into a fax number.
8
9
18
19
Enter: Confirms the selection on the display.
On Hook Dial: Engages the telephone line.
Menu: Enters Menu mode and scrolls through the available menus.
Scan To: Allows you to access a list of the PC software programs
that an image can be scanned to.
10
20
Upper Level: Sends you back to the upper menu level.
Toner Save: Allows you to save on toner by using less toner in
printing.
1.3
<Introduction>
Download from Www.Somanuals.com. All Manuals Search And Download.
Finding more information
Selecting a location
Select a level, stable place with adequate space for air circulation. Allow
extra space for opening covers and trays.
You can find information for setting up and using your machine from the
following resources, either printed or onscreen.
The area should be well-ventilated and away from direct sunlight or
sources of heat, cold, and humidity. Do not set the machine close to the
edge of your desk or table.
Quick Install
Guide
Provides information on setting up your
machine and, therefore, be sure to follow
the instructions in the guide to get the
machine ready.
Clearance space
• Front: 482.6 mm (enough space so that the tray and cover can be
opened)
• Back: 100 mm (enough space for ventilation)
• Right: 100 mm (enough space for ventilation)
• Left: 100 mm (enough space for ventilation)
Online User’s
Guide
Provides you with step-by-step
instructions for using your machine’s full
features, and contains information for
maintaining your machine,
troubleshooting, and installing
accessories.
This user’s guide also contains the
Software Section providing you with
information on how to print documents
with your machine on various operating
systems, and how to use the supplied
software utilities.
Note
You can access the user’s guides
in other languages from the
Manual folder on the printer
software CD.
Printer Driver
Help
Provides you with help information on
printer driver properties and instructions
for setting up the properties for printing. To
access a printer driver help screen, click
Help from the printer properties dialog
box.
Website
If you have Internet access, you can get
help, support, printer drivers, manuals,
and order information from the Samsung
1.4
<Introduction>
Download from Www.Somanuals.com. All Manuals Search And Download.
2 System setup
This chapter gives you an overview of menus available on your machine
and step-by-step instructions for setting up the machine’s systems.
This chapter includes:
•
•
•
•
•
•
•
•
Menu overview
The control panel provides access to various menus to set up the
machine or use the machine’s functions. These menus can be accessed
by pressing Menu. Refer to the following diagram.
Menus in the colored characters are available only with SCX-4725FN.
Machine Setup
Copy Setup
Fax Feature
Paper Setting
Fax Setup
Machine ID
Date & Time
Clock Mode
Language
Select Country
Power Save
Ignore Toner
Default Change
Timeout
DelayFax
Paper Size
Paper Type
Receive Mode
Ring to Answer
Darkness
Redial Term
Redials
MSG Confirm
Auto Report
Auto Reduction
Discard Size
RCV Start Code
DRPD Mode
Priority Fax
Add Page
Cancel Job
Reports
Advanced Fax
Sound/Volume
Maintenance
Network Setup
Phone Book
Sent Report
RCV Report
System Data
Scheduled Jobs
MSG Confirm
Junk Fax List
Toll Save
Speaker
Clean Drum
Auto Cleaning
Notify Toner
CLR Empty Msg.
Clear Memory
Reset Network
Config Network
Set To Default
Print Net CFG
Junk Fax Setup
Secure Receive
Prefix Dial
Ringer
Key Sound
Alarm Sound
Stamp RCV Name
ECM Mode
2.1
<System setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Changing the display language
The date format may differ from country to country.
To change the language that appears on the control panel, follow these
steps:
You can also use the Scroll buttons to move the cursor under the
digit you want to correct and enter a new number.
1
Press Menu until Machine Setup appears on the top line of the
4
To change AM or PM for 12-hour time format, press the
or
display.
button or any number button.
2
3
Press the Scroll buttons until Language appears and press Enter.
When the cursor is not under the AM or PM indicator, pressing the
or button immediately moves the cursor to the indicator.
Press the Scroll buttons until the language you want appears and
press Enter.
You can change the clock mode to 24-hour time format (e.g. 01:00
PM as 13:00). For details, see the next section.
4
Press Stop/Clear to return to Standby mode.
5
6
Press Enter to save the time and date.
When you enter a wrong number, Unavailable Date & Time
appears and the machine does not proceed to the next step. If this
happens, simply reenter the correct number.
Changing the country
You can select your country.
Press Stop/Clear to return to Standby mode.
1
2
3
4
Press Menu until Machine Setup appears on the top line of the
display.
Press the Scroll buttons until Select Country appears and press
Changing the clock mode
Enter.
You can set your machine to display the current time using either a
12-hour or 24-hour time format.
Press the Scroll buttons until your country appears and press
Enter.
1
Press Menu until Machine Setup appears on the top line of the
display.
Press Stop/Clear to return to Standby mode.
Note
2
Press the Scroll buttons until Clock Mode appears and press
Enter.
Changing the country clears the setting in memory.
3
4
Press the Scroll buttons to select the other mode and press Enter.
Setting the date and time
Press Stop/Clear to return to Standby mode.
The current date and time are shown on the display when your machine
is on and ready to work. All of your faxes will have the date and time
printed on them.
Setting sounds
You can control the following sounds:
Note
If power to the machine is cut off, you need to reset the correct
time and date once the power has been restored.
• Speaker: Turns on or off the sounds from the telephone line through
the speaker, such as a dial tone or a fax tone. With this option set to
Comm which means “Common,” the speaker is on until the remote
machine answers.
1
2
3
Press Menu until Machine Setup appears on the top line of the
display.
You can adjust the speaker volume level using On Hook Dial.
Press the Scroll buttons until Date & Time appears and press
Enter.
• Ringer: Adjusts the ringer volume. For the ringer volume, you can
select Off, Low, Med, and High.
Enter the correct time and date using the number keypad.
• Key Sound: Turns the key sound on or off. With this option set to On,
a tone sounds each time a key is pressed.
Day
= 01 to 31
Month
Year
Hour
= 01 to 12
• Alarm Sound: Turns the alarm sound on or off. With this option set to
On, an alarm tone sounds when an error occurs or fax communication
ends.
= requires four digits
= 01 to 12 (12-hour mode)
00 to 23 (24-hour mode)
Minute = 00 to 59
2.2
<System setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker, ringer, key sound, and alarm sound
Keypad letters and numbers
1
2
3
Press Menu until Sound/Volume appears on the top line of the
display.
Key
1
Assigned numbers, letters, or characters
Space
1
Press the Scroll buttons until the sound option you want appears
and press Enter.
2
A
D
G
J
B
E
H
K
N
Q
U
X
-
C
F
I
2
3
Press the Scroll buttons until the desired status or volume for the
sound you have selected appears and press Enter.
3
4
4
4
5
If necessary, repeat steps 2 through 3 to set other sounds.
5
L
5
Press Stop/Clear to return to Standby mode.
6
M
P
T
O
6
7
R
V
Y
S
7
Speaker volume
8
8
1
2
3
Press On Hook Dial. A dial tone sounds from the speaker.
9
W
+
Z
9
/
Press the Scroll buttons until you hear the volume you want.
0
,
.
‘
*
#
&
0
Press On Hook Dial to save the change and return to Standby
mode.
Correcting numbers or names
Note
If you make a mistake while entering a number or name, press the left
Scroll button to delete the last digit or character. Then enter the correct
digit or character.
You can adjust the speaker volume only when the telephone
line is connected.
Inserting a pause
Entering characters using the number keypad
With some telephone systems, you must dial an access code (9, for
example) and listen for a second dial tone. In such cases, you must insert
a pause in the telephone number. You can insert a pause while you are
setting up speed dial numbers.
As you perform various tasks, you may need to enter names and
numbers. For example, when you set up your machine, you enter your
name or your company’s name, and the fax number. When you store fax
numbers in memory, you may also enter the corresponding names.
To insert a pause, press Redial/Pause at the appropriate place while
entering the telephone number. A - appears on the display at the
corresponding location.
Entering alphanumeric characters
1
When you are prompted to enter a letter, locate the button labeled
with the character you want. Press the button until the correct letter
appears on the display.
Using the save modes
Toner Save mode
For example, to enter the letter O, press 6, labeled with MNO.
Each time you press 6, the display shows a different letter, M, N, O,
and finally 6.
Toner Save mode allows your machine to use less toner on each page.
Activating this mode extends the life of the toner cartridge beyond what
one would experience in the normal mode, but it reduces print quality.
You can enter special characters, such as space, plus sign, and etc.
For details, see the next section.
To turn this mode on or off, press Toner Save.
2
3
To enter additional letters, repeat step 1.
Note
If the next letter is printed on the same button, move the cursor by
pressing the right Scroll button and then press the button labeled
with the letter you want. The cursor will move to the right and the
next letter will appear on the display.
When PC-printing, you can also turn on or off Toner Save mode
in the printer properties. See the Software Section.
You can enter a space by pressing 1 twice.
When you have finished entering letters, press Enter.
2.3
<System setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Save mode
Power Save mode allows your machine to reduce power consumption
when it is not in actual use. You can select a length of time for which the
machine waits after a job is printed before it switches to a reduced power
state.
1
2
3
4
Press Menu until Machine Setup appears on the top line of the
display.
Press the Scroll buttons until Power Save appears and press
Enter.
Press the Scroll buttons until the time setting you want appears and
press Enter.
Press Stop/Clear to return to Standby mode.
2.4
<System setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
CD
Contents
3 Software overview
PostScript
printer driver
CD
Windows
• Postscript Printer Description
(PPD) file: Use the PostScript driver
to print documents with complex
fonts and graphics in the PS
language.
This chapter gives you an overview of the software that comes with your
machine. Further details about installing and using the software are
explained in the Software Section.
(SCX-4725FN
only)
This chapter includes:
• User’s Guide in PDF
•
•
•
Macintosh
• Postscript Printer Description
(PPD) file: Use this file to run your
machine from a Macintosh computer
and print documents.
• Scan driver: TWAIN driver is
available for scanning documents on
your machine.
Supplied software
You must install the printer and scanner software using the supplied CDs
after you have set up your machine and connected it to your computer.
1. Allows you to edit a scanned image in many ways using a powerful image
editor and to send the image by email. You can also open another image editor
program, like Adobe Photoshop, from SmarThru. For details, please refer to the
onscreen help supplied on the SmarThru program.
Each CD provides you with the following software:
CD
Contents
Printer
software CD
Windows
• Printer driver: Use this driver to
take full advantage of your printer’s
features.
• Scanner driver: TWAIN and
Windows Image Acquisition (WIA)
drivers are available for scanning
documents on your machine.
• Smart Panel: This program allows
you to monitor the machine’s status
and alerts you when an error occurs
during printing.
1
• SmarThru : This is the
accompanying Windows-based
software for your multifunctional
machine.
• User’s Guide in PDF
• Set IP: Use this program to set your
machine’s TCP/IP addresses.
Linux
• Printer driver: Use this driver to run
your machine from a Linux computer
and print documents.
• SANE: Use this driver to scan
documents.
3.1
<Software overview>
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer driver features
System requirements
Your printer drivers support the following standard features:
• Paper source selection
Before you begin, ensure that your system meets the following
requirements:
• Paper size, orientation and media type
• Number of copies
Windows
Item
Requirements
Recommended
In addition, you can use various special printing features. The following
table shows a general overview of features supported by your printer
drivers:
Operating
system
Windows 98/Me/2000/XP(32/64bit)/2003(32/64bit)
PostScript
CPU
RAM
Windows 98/
Me/2000
Pentium II
400 MHz or
higher
Pentium III
933 MHz
PCL 6
(SCX-4725FN only)
Feature
Windows
Windows
Macintosh
Linux
O
Windows
XP(32/64bit)/
2003(32/64bit)
Pentium III
933 MHz or
higher
Pentium IV
1 GHz
Toner save
O
O
O
O
X
Print quality
option
O
O
Windows 98/
Me/2000
64 MB or more
128 MB
256 MB
Poster
printing
O
O
X
X
X
Windows
XP(32/64bit)/
2003(32/64bit)
128 MB or more
Multiple
O
O
O
(2, 4)
pages per
sheet (N-up)
Free disk
space
Windows 98/
Me/2000
300 MB or more
1 GB or more
1 GB
5 GB
Fit to page
printing
O
O
O
X
Windows
XP(32/64bit)/
2003(32/64bit)
Scale printing
Watermark
Overlay
O
O
O
O
X
X
O
X
X
X
X
X
Internet
Explorer
5.0 or higher
Note
For Windows 2000/XP(32/64bit)/2003(32/64bit), users who
have an administrator right can install the software.
3.2
<Software overview>
Download from Www.Somanuals.com. All Manuals Search And Download.
Linux
Item
Requirements
• Red Hat 8.0 ~ 9.0
Operating system
• Fedora Core 1 ~ 4
• Mandrake 9.2 ~ 10.1
• SuSE 8.2 ~ 9.2
CPU
Pentium IV 1 GHz or higher
256 MB or higher
RAM
Free disk space
Software
1 GB or higher
• Linux Kernel 2.4 or higher
• Glibc 2.2 or higher
• CUPS
• SANE (for MFP device only)
Notes
• It is necessary to claim swap partition of 300 MB or larger for
working with large scanned images.
• The Linux scanner driver supports the optical resolution at
maximum.
Macintosh (SCX-4725FN only)
Item
Operating system
RAM
Requirements
Macintosh 10.3 ~ 10.4
128 MB
Free disk space
Connection
200 MB
USB interface, Network interface
3.3
<Software overview>
Download from Www.Somanuals.com. All Manuals Search And Download.
Via the control panel
4 Network setup
(SCX-4725FN only)
You can set up the following basic network parameters through the
machine’s control panel:
Connecting your machine to a network is available only on the
SCX-4725FN. This chapter gives you step-by-step instructions for setting
up your machine for network connections.
• Configure TCP/IP
• Configure EtherTalk
This chapter includes:
•
•
•
•
•
•
•
•
Supported operating systems
The following table shows the network environments supported by the
machine:
Using SetIP program
Item
Requirements
• 10/100 Base-TX
Network interface
Network operating
system
• Windows 98/Me/2000/XP(32/64bit)/
2003(32/64bit)
• Various Linux OS
• Macintosh OS 10.3~10.4
Introduction
Network protocols
• TCP/IP on Windows
• EtherTalk
Once you have connected your machine to a network with an RJ-45
Ethernet cable, you can share the machine with other network users.
You need to set up the network protocols on the machine to use it as your
network printer. Protocols can be set up by the following two methods:
Dynamicaddressing • DHCP, BOOTP
server
• TCP/IP: Transmission Control Protocol/Internet Protocol
• DHCP: Dynamic Host Configuration Protocol
• BOOTP: Bootstrap Protocol
Via network administration programs
You can configure your machine’s print server settings and manage the
machine via the following programs that came with your machine:
• SyncThru™ Web Admin Service: Web-based printer management
solution for network administrators. SyncThru™ Web Admin Service
provides you with an efficient way of manageing network devices and
lets you remotely monitor and troubleshoot network machines from
any sith with corporate internet access. Download this program from
Configuring TCP/IP
Your machine can be set up with a variety of TCP/IP network information,
such as an IP address, a subnet mask, and a gateway. There are several
ways in which your machine can be assigned a TCP/IP address,
depending on your network.
• SyncThru™ Web Service: A web server embedded to your network
print server, which allows you to:
• Static addressing: A TCP/IP address is assigned manually by the
system administrator.
- Configure the network parameters necessary for the machine to
connect to various network environments.
• Dynamic addressing via BOOTP/DHCP (default): A TCP/IP address is
assigned automatically by the server.
- Customize printer, copy, and fax settings.
• SetIP: Utility program allowing you to select a network interface and
manually configure the IP addresses for use with the TCP/IP protocol.
See Using SetIP program on page 4.2.
Note
Before configuring TCP/IP, you need to set the network protocol
to TCP/IP.
4.1
<
Network setup (SCX-4725FN only)>
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
5
Press the Scroll buttons until EtherTalk appears and press Enter.
Press the Scroll buttons until On appears and press Enter.
Press Stop/Clear to return to Standby mode.
Static addressing
To enter a TCP/IP address from your machine’s control panel, take the
following steps:
1
Press Menu until Network Setup appears on the top line of the
display.
Restoring the network configuration
2
Press the Scroll buttons until Config Network appears and press
Enter.
You can return the network configuration to its default settings.
3
4
5
6
Press Enter when TCP/IP appears.
Press Enter when Manual appears.
Press Enter when IP Address appears.
1
Press Menu until Network Setup appears on the top line of the
display.
2
Press the Scroll buttons until Set To Default appears and press
Enter.
Enter a byte between 0 and 255 using the number keypad and
press the Scroll buttons to move between bytes.
3
4
Press Enter when Yes appears to restore the network configuration.
Repeat this to complete the address from the 1st byte to the 4th
byte.
Power the machine off and back on.
7
8
When you have finished, press Enter.
Printing a network configuration page
Repeat steps 6 and 7 to configure the other TCP/IP parameters:
subnet mask and gateway address.
The network configuration page shows how the network interface on your
machine is configured.
9
Press Stop/Clear to return to Standby mode.
1
2
3
Press Menu until Network Setup appears on the top line of the
display.
Dynamic addressing (BOOTP/DHCP)
Press the Scroll buttons until Print Net CFG appears and press
Enter.
To have a TCP/IP address assigned automatically by the server, take the
following steps:
Press Enter when Yes appears.
1
Press Menu until Network Setup appears on the top line of the
display.
The network configuration page prints out.
2
Press the Scroll buttons until Config Network appears and press
Enter.
Resetting the network interface
3
4
Press Enter when TCP/IP appears.
You can reset the embedded network interface when a network problem
occurs.
Press the Scroll buttons until DHCP or BOOTP appears and press
Enter.
1
Press Menu until Network Setup appears on the top line of the
display.
5
Press Stop/Clear to return to Standby mode.
2
Press Enter when Reset Network appears.
Configuring EtherTalk
The machine resets the network interface.
EtherTalk is AppleTalk used in an Ethernet network. This protocol is
widely used in Macintosh network environments. To use EtherTalk, take
the following steps:
Using SetIP program
1
Press Menu until Network Setup appears on the top line of the
display.
This program is for the network IP setting using the MAC address which
is the hardware serial number of the network printer card or interface.
Especially, it is for the network administrator to set several network IPs at
the same time.
2
Press the Scroll buttons until Config Network appears and press
Enter.
1
Insert the driver CD provided along with your machine.
4.2
<Network setup (SCX-4725FN only)>
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Start Windows Explorer and open the X drive. (X represents your
CD-ROM drive.)
3
4
5
6
Double click Application > SetIP.
Open the language folder you want to use.
Double click Setup.exe to install this program.
From the Windows Start menu, select Programs > Samsung
Network Printer Utilities > SetIP.
7
Select the name of your printer and click "
".
Note
If you cannot find your printer name click "
list.
" to refresh the
8
Enter the network card's MAC address, IP address, subnet mask,
default gateway, and then click Apply.
Note
If you do not know the network card's MAC address, print the
machine's network information report.
9
Click OK to confirm the settings.
10 Click Exit to close the SetIP program.
4.3
<Network setup (SCX-4725FN only)>
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Place the original face down on the scanner glass and align it with
the registration guide at the top left corner of the glass.
5 Loading originals and print
media
This chapter introduces you to how to load originals and print media into
your machine.
This chapter includes:
•
•
•
•
•
Loading originals
You can use the scanner glass or ADF to load an original for copying,
scanning, and sending a fax.
On the scanner glass
3
Close the scanner lid.
Make sure that no originals are in the ADF. If an original is detected in the
ADF, the machine gives it priority over the original on the scanner glass.
To get the best scan quality, especially for colored or gray-scaled images,
use the scanner glass.
Notes
• Leaving the scanner lid open while copying may affect copy
quality and toner consumption.
• Dust on the scanner glass may cause black spots on the
printout. Always keep it clean.
1
Lift and open the scanner lid.
In the ADF
Using the ADF, you can load up to 30 sheets of paper (75 g/m2) for one
job.
When you use the ADF:
• Do not load paper smaller than 142 x 148 mm or larger than
216 x 356 mm.
• Do not attempt to load the following types of paper:
- carbon-paper or carbon-backed paper
- coated paper
- onion skin or thin paper
- wrinkled or creased paper
- curled or rolled paper
- torn paper
• Remove all staples and paper clips before loading.
• Make sure any glue, ink, or correction fluid on the paper is completely
dry before loading.
• Do not load originals that include different sizes or weights of paper.
• Do not load booklets, pamphlets, transparencies, or documents
having other unusual characteristics.
5.1
<Loading originals and print media>
Download from Www.Somanuals.com. All Manuals Search And Download.
To load an original into the ADF:
Selecting print media
1
Load the original face up into the ADF. Make sure that the bottom of
the original stack matches the paper size marked on the document
input tray.
You can print on a variety of print media, such as plain paper, envelopes,
labels, and transparencies. Always use print media that meet the
guidelines for use with your machine. Print media that does not meet the
guidelines outlined in this user’s guide may cause the following problems:
• Poor print quality
• Increased paper jams
• Premature wear on the machine.
Properties, such as weight, composition, grain, and moisture content, are
important factors that affect the machine’s performance and the output
quality. When you choose print materials, consider the following:
• Desired outcome: The print media you choose should be appropriate
for your project.
• Size: You can use any size media that fits easily within the paper
adjusters of the paper tray.
• Weight: Your machine supports print media weights as follows:
- 60 to 90 g/m2 bond for the tray
- 60 to 165 g/m2 bond for the manual tray
• Brightness: Some print media are whiter than others and produce
sharper, more vibrant images.
2
Adjust the document width guides to the paper size.
• Surface smoothness: The smoothness of the print media affects how
crisp the printing looks on the paper.
Notes
• Some print media may meet all of the guidelines in this section
and still not produce satisfactory results. This may be the result
of improper handling, unacceptable temperature and humidity
levels, or other variables over which Samsung has no control.
• Before purchasing large quantities of print media, ensure that it
meets the requirements specified in this user’s guide.
Caution
Using print media that does not meet these specifications may
cause problems, requiring repairs. Such repairs are not covered
by Samsung’s warranty or service agreements.
Note
Dust on the ADF glass may cause black lines on the printout.
Always keep it clean.
5.2
<Loading originals and print media>
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported print media types and sizes
1
2
Type
Plain paper
Size
Dimensions
Weight
Capacity
Letter
Legal
Folio
216 x 279 mm (8.5 x 11 inches)
216 x 356 mm (8.5 x 14 inches)
216 x 330.2 mm (8.5 x 13 inches)
216 x 343 mm (8.5 x 13.5 inches)
210 x 297 mm (8.27 x 11.69 inches)
182 x 257 mm (7.18 x 10.12 inches)
176 x 250 mm (6.93 x 9.84 inches)
184.2 x 266.7 mm (7.25 x 10.5 inches)
148.5 x 210 mm (5.85 x 8.27 inches)
105 x 148.5 mm (4.13 x 5.85 inches)
176 x 250 mm (6.93 x 9.84 inches)
98.4 x 190.5 mm (3.88 x 7.5 inches)
105 x 241 mm (4.12 x 9.5 inches)
110 x 220 mm (4.33 x 8.66 inches)
162 x 229 mm (6.38 x 9.02 inches)
114 x 162 mm (4.49 x 6.38 inches)
Refer to the Plain paper section
• 60 to 90 g/m2 (16 to 24 lb
bond) for the tray
• 250 sheets of 75 g/m2
(20 lb bond) paper for the
tray
• 60 to 165 g/m2 (16 to 43 lb
bond) for the manual tray
• 1 sheet for the manual tray
Oficio
A4
JIS B5
ISO B5
Executive
A5
A6
Envelope
Envelope B5
Envelope Monarch
Envelope COM-10
Envelope DL
Envelope C5
Envelope C6
Letter, A4
75 to 90 g/m2 (20 lb to 24 lb
bond)
1 sheet for the manual tray
2
Transparency
Labels
138 to 146 g/m (37 to 39 lb
1 sheet for the manual tray
1 sheet for the manual tray
bond)
2
Letter, Legal, Folio,
A4, JIS B5, ISO B5,
Executive, A5, A6
Refer to the Plain paper section
Refer to the Plain paper section
120 to 150 g/m (32 to 40 lb
bond)
2
Card stock
Letter, Legal, Folio,
A4, JIS B5, ISO B5,
Executive, A5, A6
60 to 165 g/m (16 to 43 lb
1 sheet for the manual tray
1 sheet for the manual tray
bond)
2
Minimum size (custom)
Maximum size (custom)
76 x 127 mm (3 x 5 inches)
60 to 165 g/m (16 to 43 lb
bond)
215.9 x 356 mm (8.5 x 14 inches)
1. If media weight is over 90 g/m2, use the manual tray.
2. Maximum capacity may differ depending on media weight, thickness, and environmental conditions.
5.3
<Loading originals and print media>
Download from Www.Somanuals.com. All Manuals Search And Download.
Guidelines for special print media
Media sizes supported in each mode
Media type
Guidelines
Mode
Size
Source
Envelopes
• Successful printing on envelopes depends upon
the quality of the envelopes. When selecting
envelopes, consider the following factors:
- Weight: The weight of the envelope paper
should not exceed 90 g/m2 or jamming may
occur.
- Construction: Prior to printing, envelopes
should lie flat with less than 6 mm curl, and
should not contain air.
Copy mode
Letter, A4, Legal, Folio, • tray
Executive, ISO B5, JIS
B5, A5, A6
• manual tray
Print mode
Fax mode
All sizes supported by
the machine
• tray
• manual tray
Letter, A4, Legal
• tray
• manual tray
- Condition: Envelopes should not be wrinkled,
nicked, or otherwise damaged.
- Temperature: You should use envelopes that
are compatible with the heat and pressure of
the machine during operation.
• Use only well-constructed envelopes with sharp
and well creased folds.
• Do not use stamped envelopes.
Guidelines for selecting and storing print media
When selecting or loading paper, envelopes, or other print materials,
keep these guidelines in mind:
• Always use print media that conform with the specifications listed on
• Do not use envelopes with clasps, snaps,
windows, coated lining, self-adhesive seals, or
other synthetic materials.
• Do not use damaged or poorly made envelopes.
• Be sure the seam at both ends of the envelope
extends all the way to the corner of the
envelope.
• Attempting to print on damp, curled, wrinkled, or torn paper can cause
paper jams and poor print quality.
• For the best print quality, use only high quality copier grade paper
specifically recommended for use in laser printers.
• Avoid using the following media types:
- Paper with embossed lettering, perforations, or a texture that is too
smooth or too rough
- Erasable bond paper
- Multi-paged paper
- Synthetic paper and thermally reactive paper
- Carbonless paper and tracing paper
Acceptable
Use of these types of paper could result in paper jams, chemical
smells, and damage to your machine.
• Store print media in its ream wrapper until you are ready to use it.
Place cartons on pallets or shelves, not on the floor. Do not place
heavy objects on top of the paper, whether it is packaged or
unpackaged. Keep it away from moisture or other conditions that can
cause it to wrinkle or curl.
Unacceptable
• Envelopes with a peel-off adhesive strip or with
more than one flap that folds over to seal must
use adhesives compatible with the machine’s
fusing temperature of 180 °C for 0,1 second.
The extra flaps and strips might cause wrinkling,
creasing, or jams, and may even damage the
fuser.
• For the best print quality, position margins no
closer than 15 mm from the edges of the
envelope.
• Store unused print media at temperatures between 15 °C and 30 °C.
The relative humidity should be between 10% and 70%.
• Store unused print media in a moisture-proof wrap, such as a plastic
container or bag, to prevent dust and moisture from contaminating
your paper.
• Load special media types one sheet at a time through the manual tray
to avoid paper jams.
• To prevent print media, such as transparencies and label sheets, from
sticking together, remove them as they print out.
• Avoid printing over the area where the
envelope’s seams meet.
Caution
If you print 20 envelopes in succession, the surface of the rear
cover may become hot. Please exercise caution.
5.4
<Loading originals and print media>
Download from Www.Somanuals.com. All Manuals Search And Download.
Media type
Guidelines
Media type
Guidelines
Transparencies • To avoid damaging the machine, use only
transparencies designed for use in laser printers.
• Transparencies used in the machine must be
able to withstand 180 °C, the machine’s fusing
temperature.
Preprinted
paper
• Letterhead must be printed with heat-resistant
ink that will not melt, vaporize, or release
hazardous emissions when subjected to the
machine’s fusing temperature of 180 °C for
0,1 second.
• Place them on a flat surface after removing them
from the machine.
• Do not leave them in the paper tray for long
periods of time. Dust and dirt may accumulate
on them, resulting in spotty printing.
• Letterhead ink must be non-flammable and
should not adversely affect printer rollers.
• Forms and letterhead should be sealed in a
moisture-proof wrapping to prevent changes
during storage.
• To avoid smudging caused by fingerprints,
handle them carefully.
• To avoid fading, do not expose printed
transparencies to prolonged sunlight.
• Ensure that transparencies are not wrinkled,
curled, or have any torn edges.
• Before you load preprinted paper, such as forms
and letterhead, verify that the ink on the paper is
dry. During the fusing process, wet ink can come
off preprinted paper, reducing print quality.
Loading paper
Labels
• To avoid damaging the machine, use only labels
designed for use in laser printers.
• When selecting labels, consider the following
factors:
In the tray
- Adhesives: The adhesive material should be
stable at 180 °C, the machine’s fusing
temperature.
Load the print media you use for the majority of your print jobs in the tray.
The tray can hold a maximum of 250 sheets of 75 g/m2 plain paper.
- Arrangement: Only use labels with no
exposed backing between them. Labels can
peel off sheets that have spaces between the
labels, causing serious jams.
1
Open the tray. Squeeze the paper length guide and pull it out to
extend the tray.
- Curl: Prior to printing, labels must lie flat with
no more than 13 mm of curl in any direction.
- Condition: Do not use labels with wrinkles,
bubbles, or other indications of separation.
• Make sure that there is no exposed adhesive
material between labels. Exposed areas can
cause labels to peel off during printing, which
can cause paper jams. Exposed adhesive can
also cause damage to machine components.
• Do not run a sheet of labels through the machine
more than once. The adhesive backing is
designed for only a single pass through the
machine.
1
2
• Do not use labels that are separating from the
backing sheet or are wrinkled, bubbled, or
otherwise damaged.
tray
1
2
paper length guide
Card stock or
custom-sized
materials
• Do not print on media smaller than 98 mm wide
or 148 mm long.
• In the software application, set margins at least
6,4 mm away from the edges of the material.
2
If you are using paper, flex or fan the edge of the paper stack to
separate the pages before loading.
5.5
<Loading originals and print media>
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Load the paper with the side to be printed on facing up.
Notes
• If you experience problems with paper feed, place one sheet at
a time in the manual tray.
• You can load previously printed paper. The printed side should
be facing down with an uncurled edge at the front. If you
experience problems with paper feed, turn the paper around.
Note that print quality is not guaranteed.
In the manual tray
The manual tray can hold special size and type of print material, such as
transparency, postcard, note card, and envelope. The manual tray can
hold 1 sheet of paper.
To load paper in the manual tray:
1
Load the paper with the side to be printed on facing up.
4
5
Squeeze the paper width guide and adjust it to the width of the
paper.
Squeeze the paper length guide and adjust it to the length of the
paper.
Notes
Depending on the media type you are using, keep the following
loading guidelines:
Notes
• Do not push the paper width guide far enough to cause
the materials to warp.
• If you do not adjust the paper width guide, it may cause
paper jams.
• Envelopes: Flap side down and with the stamp area on the top
left side.
• Transparencies: Print side up and the top with the adhesive
strip entering the machine first.
• Labels: Print side up and top short edge entering the machine
first.
• Preprinted paper: Design side up with the top edge toward the
machine.
• Card stock: Print side up and the short edge entering the
machine first.
• Previously printed paper: Previously printed side down with an
uncurled edge toward the machine.
6
After loading paper, set the paper type and size for the tray. See
printing.
2
Adjust the manual tray paper width guides to the width of the paper.
Do not force too much, or the paper will be bent, which will result in
a paper jam or skew.
5.6
<Loading originals and print media>
Download from Www.Somanuals.com. All Manuals Search And Download.
3
After loading paper, set the paper type and size for the manual tray.
See the next section for copying and faxing or the Software
Section for PC-printing.
Verifying an output location
The machine has a paper output location which holds 100 sheets of paper.
Note
The settings made from the printer driver override the
settings on the control panel.
Tips on using the manual tray
• Load only one sheet of print media at a time in the manual tray.
• To prevent paper jams, do not add paper when there is still paper in
the manual tray. This also applies to other types of print media.
• Print media should be loaded face up with the top edge going into the
manual tray first and be placed in the center of the tray.
1
jams and print quality problems.
• Flatten any curl on postcard, envelope, and label before loading it into
the manual tray.
output tray
1
Setting the paper size and type
The output tray collects printed paper face down, in the order in which
the sheets were printed.
After loading paper in the paper tray, you need to set the paper size and
type using the control panel buttons. These settings will apply to Copy
and Fax modes. For PC-printing, you need to select the paper size and
type in the application program you use on your PC.
Note
Pull the output support not to drop the printed paper.
1
2
3
Press Menu. Paper Setting appears on the top line of the display.
Press the Scroll buttons until Paper Size appears and press Enter.
Press the Scroll buttons until the paper tray you want appears and
press Enter.
4
Press the Scroll buttons until the paper size you are using appears
and press Enter.
5
6
7
Press upper level to return to the upper level.
Press the Scroll buttons until Paper Type appears and press Enter.
Press the Scroll buttons until the paper type you are using appears
and press Enter.
8
Press Stop/Clear to return to Standby mode.
5.7
<Loading originals and print media>
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the settings for each copy
6 Copying
Your machine provides default settings for copying so that you can
quickly and easily make a copy. However, if you want to change the
options for each copy, use the copy function buttons on the control panel.
This chapter gives you step-by-step instructions for copying documents.
This chapter includes:
•
•
•
•
•
Note
If you press Stop/Clear while setting the copy options, all of the
options you have set for the current copy job will be canceled
and returned to their default status. Or, they will automatically
return to their default status after the machine completes the
copy in progress.
Darkness
Copying
If you have an original containing faint markings and dark images, you
can adjust the brightness to make a copy that is easier to read.
1
2
Load originals face up into the ADF, or place a single original face
down on the scanner glass.
To adjust the darkness of copies, press Darkness. Each time you press
the button, the following modes are available:
• Light: Works well with dark print.
If you want to customize the copy settings including darkness,
original type, the number of copies, and copy size, by using the
control panel buttons, see the next section.
• Normal: Works well with standard typed or printed originals.
• Dark: Works well with light print or faint pencil markings.
If necessary, you can use special copy features, such as poster
copying, 2- or 4-up copying. See page 6.2.
Original Type
The original type setting is used to improve the copy quality by selecting
the document type for the current copy job.
3
Press Start to begin copying.
Note
To select the document type, press Original Type. Each time you press
the button, the following modes are available:
You can cancel the copy job during an operation. Press Stop/
Clear, and the copying will stop.
• Text: Use for originals containing mostly text.
• Text/Photo: Use for originals with mixed text and photographs.
• Photo: Use when the originals are photographs.
Number of copies
You can select the number of copies from 1 to 99.
To change the number of copies:
1
2
3
Press No. of Copies.
Enter the value using the number keypad.
Press Enter to save the selection.
6.1
<Copying>
Download from Www.Somanuals.com. All Manuals Search And Download.
Reduced or enlarged copy
Using special copy features
By using the Reduce/Enlarge button, you can reduce or enlarge the size
of a copied image from 25% to 400% when you copy original documents
from the scanner glass, or from 25% to 100% from the ADF.
You can use the following copy features:
Clone copying
To select from the predefined copy sizes:
1
2
Press Reduce/Enlarge.
Your machine can print multiple image copies from the
original document on a single page. The number of
images is automatically determined by the original
image and paper size.
Press Reduce/Enlarge or the Scroll buttons until the size setting
you want appears and press Enter.
To scale the copy by directly entering the scale rate:
This copy feature is available only when you place
originals on the scanner glass.
1
2
Press Reduce/Enlarge.
1
Place a single original face down on the scanner
glass.
Press Reduce/Enlarge or the Scroll buttons until Custom appears
and press Enter.
For details about loading an original, see
page 5.1.
3
Enter the scale rate and press Enter to save the selection.
Note
2
3
Press Favorite Copy until Clone appears on the
bottom line of the display and press Enter.
When you make a reduced copy, black lines may appear at the
bottom of your copy.
Press Start to begin copying.
Note
Changing the default copy settings
You cannot adjust the copy size using the
Reduce/Enlarge button while making a
clone copy.
The copy options, including darkness, original type, copy size, and
number of copies, can be set to those most frequently used. When you
copy a document, the default settings are used unless they have been
changed by using the corresponding buttons on the control panel.
Collation
1
2
3
Press Menu until Copy Setup appears on the top line of the display.
You can set the machine to sort the copy job. For
example, if you make 2 copies of a 3 page original,
one complete 3 page document will print followed by a
second complete document.
Press Enter when Default Change appears.
Press the Scroll buttons until the setup option you want appears
and press Enter.
This copy feature is available only when you load
originals into the ADF.
4
Press the Scroll buttons until the setting you want appears and
press Enter.
1
Load originals face up into the ADF.
5
6
Repeat steps 3 through 4, as needed.
For details about loading an original, see
Press Stop/Clear to return to Standby mode.
2
3
4
Enter the number of copies using the number
keypad.
Note
While you are setting copy options, pressing Stop/Clear
cancels the changed settings and restores the defaults.
Press Favorite Copy until Copy Collate appears
on the bottom line of the display and press Enter.
Press Start to begin copying.
One complete document will print followed by the
second complete document.
6.2
<Copying>
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto fit
3
4
Press Start to begin copying.
Your machine begins scanning the front side and
shows Set BackSide.
Your machine can automatically reduce or enlarge the
original image to fit on the paper currently loaded in
the machine.
A
Open the scanner lid and turn the original over.
This copy feature is available only when you place
originals on the scanner glass.
Note
If you press Stop/Clear or if no buttons
are pressed for approximately
30 seconds, the machine cancels the
copy job and returns to Standby mode.
1
Place a single original face down on the scanner
glass.
For details about loading an original, see
5
Press Start to begin copying.
Note
2
3
Press Favorite Copy until Autofit appears on
the bottom line of the display and press Enter.
If the original is larger than the printable area,
some portions may not be printed.
Press Start to begin copying.
Note
2-up or 4-up copying
You cannot adjust the copy size using the
Reduce/Enlarge button while making a Auto
fit copy.
Your machine can print 2 or 4 original images reduced
to fit onto one sheet of paper.
This copy feature is available only when you load
originals into the ADF.
ID card copying
1
Load originals face up in the ADF.
Your machine can print 2-sided originals on one sheet
of A4-, Letter-, Legal-, Folio-, Executive-, B5-, A5-, or
A6-sized paper.
For details about loading an original, see
page 5.1.
2-up copying
1
2
2
3
Press Favorite Copy until 2 UP or 4 UP appears
on the bottom line of the display and press Enter.
When you copy using this feature, the machine prints
one side of the original on the upper half of the paper
and the other side on the lower half without reducing
the size of the original. This feature is helpful for
copying a small-sized item, such as a name card.
3
4
Press Start to begin copying.
Note
4-up copying
This copy feature is available only when you place
originals on the scanner glass.
You cannot adjust the copy size using the
Reduce/Enlarge button while making a 2- or
4-up copy.
1
Place a single original face down on the scanner
glass.
For details about loading an original, see
page 5.1.
2
Press Favorite Copy until ID Card Copy
appears on the bottom line of the display and
press Enter.
6.3
<Copying>
Download from Www.Somanuals.com. All Manuals Search And Download.
Poster copying
Your machine can print an image onto 9 sheets of
paper (3x3). You can paste the printed pages together
to make one poster-sized document.
This copy feature is available only when you place
originals on the scanner glass.
1
Place a single original face down on the scanner
glass.
For details about loading an original, see
page 5.1.
2
3
Press Favorite Copy until Poster appears on
the bottom line of the display and press Enter.
Press Start to begin copying.
Note
You cannot adjust the copy size using the
Reduce/Enlarge button while making a
poster copy.
Your original is divided into
9 portions. Each portion is scanned
and printed one by one in the
following order:
Setting copy timeout
You can set the time the machine waits before it restores the default copy
settings, if you do not start copying after changing them on the control
panel.
1
2
3
Press Menu until Copy Setup appears on the top line of the display.
Press the Scroll buttons until Timeout appears and press Enter.
Press the Scroll buttons until the time setting you want appears.
Selecting Off means that the machine does not restore the default
settings until you press Start to begin copying, or Stop/Clear to
cancel.
4
5
Press Enter to save your selection.
Press Stop/Clear to return to Standby mode.
6.4
<Copying>
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Basic printing
This chapter explains common printing tasks.
Printing a document
1
Your machine allows you to print from various Windows, Macintosh , or
Linux applications. The exact steps for printing a document may vary
depending on the application you use.
For details about printing, see the Software Section.
Canceling a print job
If the print job is waiting in a print queue or print spooler, such as the
printer group in Windows, delete the job as follows:
1
2
Click the Windows Start menu.
For Windows 98/2000/Me, select Settings and then Printers.
For Windows XP(32/64bit)/2003(32/64bit), select Printers and
Faxes.
3
4
Double-click the Samsung SCX-4725 Series icon.
From the Document menu, select Cancel Printing (Windows 98/
Me) or Cancel (Windows 2000/XP(32/64bit)/2003(32/64bit).
Note
You can also access this window by simply double-clicking the
printer icon at the bottom right corner of the Windows desktop.
You can also cancel the current job by pressing Stop/Clear on the control
panel.
1.SCX-4725FN only
7.1
<Basic printing>
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Scanning
Scanning with your machine lets you turn pictures and text into digital files
that can be stored on your computer. Then you can fax or email the files,
upload them to your website, or use them to create projects that you can
print.
Scanning basics
Your machine offers the following ways to scan an image:
• Via one of the preset imaging applications. Scanning an image
launches the selected application, enabling you to control the
scanning process. See the next section.
• Via the SmarThru™ program supplied with your machine. Scanning
an image launches SmarThru™ and enables you to control the
scanning process.
• Via the Windows Images Acquisition (WIA) driver. See the Software
Section.
Scanning to an application
1
2
Make sure that your machine and computer are turned on and
properly connected to each other.
Load originals face up into the ADF, or place a single original face
down on the scanner glass.
3
4
Press Scan To. Application appears on the top line of the display.
Press the Scroll buttons until the application you want to use
appears and press Enter.
• Microsoft Paint: Sends the scanned image to Microsoft Paint.
• Email: Sends the scanned image to your default email program on
your computer. A new message window opens with the image
attached.
• My Documents: Saves the scanned image in the default folder,
My Documents, on your computer.
• SmarThru: Sends the scanned image to SmarThru™, installed
with the printer driver.
Note
You can add more TWAIN-compliant software for scanning,
such as Adobe Photoshop Deluxe, or Adobe Photoshop,
from the Printer Settings Utility. See the Software
Section.
5
On the selected application, adjust the scan settings and begin
scanning. For details, please refer to the application user's guide.
8.1
<Scanning>
Download from Www.Somanuals.com. All Manuals Search And Download.
Sending a fax
9 Faxing
This chapter gives you information about using your machine as a fax
machine.
Setting the fax header
This chapter includes:
In some countries, you are required by law to indicate your fax number
on any fax you send. The Machine ID, containing your telephone number
and name or company name, will be printed at the top of each page sent
from your machine.
•
•
•
•
•
•
•
1
Press Menu until Machine Setup appears on the top line of the
display.
2
3
4
Press Enter when Machine ID appears.
Enter your fax number using the number keypad and press Enter.
Enter your name or the company name using the number keypad.
You can enter alphanumeric characters using the number keypad,
and include special symbols by pressing the 0 button.
•
•
•
•
•
•
•
•
5
Press Enter to save the ID.
Adjusting the document settings
Before starting a fax, change the following settings according to your
original’s status to get the best quality.
Resolution
•
•
•
The default document settings produce good results when using typical
text-based originals. However, if you send originals that are of poor
quality, or contain photographs, you can adjust the resolution to produce
a higher quality Fax.
1
2
Press Resolution.
Press Resolution or the Scroll buttons until the option you want
appears.
3
Press Enter to save your selection.
9.1
<Faxing>
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended resolution settings for different original document types
are described in the table below:
Sending a fax automatically
1
Load originals face up into the ADF, or place a single original face
down on the scanner glass.
Mode
Standard
Fine
Recommended for:
Originals with normal sized characters.
Originals containing small characters or thin lines or
originals printed using a dot-matrix printer.
2
3
Adjust the resolution and the darkness to suit your fax needs. See
page 9.1.
Super Fine
Originals containing extremely fine detail. Super
Fine mode is enabled only if the machine with
which you are communicating also supports the
Super Fine resolution.
Enter the receiving fax machine’s number.
You can use speed dial numbers, or group dial numbers. For details
about storing and searching for a number, see page 10.3.
Notes
4
5
Press Start.
• For memory transmission, Super Fine
mode is not available. The resolution
setting is automatically changed to Fine.
If an original is placed on the scanner glass, load another original
and press 1 to add another page.
• When your machine is set to Super Fine
resolution and the fax machine with
which you are communicating does not
support Super Fine resolution, the
machine transmits using the highest
resolution mode supported by the other
fax machine.
6
When you have finished, press 2 at the Another Page ? prompt.
After the number is dialed, the machine begins sending the fax
when the receiving fax machine answers.
Note
When you want to cancel a fax job, press Stop/Clear at any
time while sending.
Photo Fax
Color Fax
Originals containing shades of gray or photographs.
Originals with colors. Sending a color fax is enabled
only if the machine with which you are
communicating supports color fax reception and
you send the fax manually. In this mode, memory
transmission is not available.
Sending a fax manually
1
2
Load originals face up into the ADF, or place a single original face
down on the scanner glass.
Note
The resolution setting is applied to the current fax job.
Adjust the resolution and the darkness to suit your fax needs. See
page 9.1.
3
4
Press On Hook Dial. You hear a dial tone.
Darkness
Enter the receiving fax machine’s number.
You can select the default contrast mode to fax your originals lighter or
darker.
You can use speed dial numbers, or group dial numbers. For details
about storing and searching for a number, see page 10.3.
1
2
3
Press Menu until Fax Setup appears on the top line of the display.
5
Press Start when you hear a high-pitched fax signal from the
remote fax machine.
Press the Scroll buttons until Darkness appears and press Enter.
Press the Scroll buttons until the option you want appears and
Note
press Enter.
When you want to cancel a fax job, press Stop/Clear at any
time while sending.
4
Press Stop/Clear to return to Standby mode.
Note
The darkness setting is applied to the current fax job.
9.2
<Faxing>
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving a fax
Confirming a transmission
When the last page of your original has been sent successfully, the
machine beeps and returns to Standby mode.
Changing receiving modes
When something goes wrong while sending your fax, an error message
appears on the display. For a list of error messages and their meanings,
clear the message and try to send the fax again.
1
2
3
Press Menu until Fax Setup appears on the top line of the display.
Press Enter when Receive Mode appears.
You can set your machine to print a confirmation report automatically
Press the Scroll buttons until the fax reception mode you want
appears.
• In Fax mode, the machine answers an incoming fax call and
immediately goes into the fax reception mode.
Automatic redialing
• In Tel mode, you can receive a fax by pressing On Hook Dial and
then Start. You can also pick up the handset of the extension
When the number you have dialed is busy or there is no answer when you
send a fax, the machine automatically redials the number every three
minutes, up to seven times according to the factory default settings.
• In Ans/Fax mode, an answering machine attached to your
machine answers an incoming call, and the caller can leave a
message on the answering machine. If the fax machine senses a
fax tone on the line, the machine automatically switches to Fax
mode to receive the fax. See page 9.4.
When the display shows Retry Redial?, press Enter to redial the number
without waiting. To cancel the automatic redialing, press Stop/Clear.
To change the time interval between redials and the number of redial
• In DRPD mode, you can receive a call using the Distinctive Ring
Pattern Detection (DRPD) feature. Distinctive Ring is a telephone
company service which enables an user to use a single telephone
line to answer several different telephone numbers. For further
details, see page 9.4.
Redialing the last number
To redial the number you called last:
4
5
Press Enter to save your selection.
1
2
Press Redial/Pause.
Press Stop/Clear to return to Standby mode.
When an original is loaded in the ADF, the machine automatically
begins to send.
Notes
• When the memory is full, the printer can no longer receive any
incoming fax. Secure free memory to resume by removing data
stored in the memory.
3
If an original is placed on the scanner glass, load another original
and press 1 to add another page.
• To use the Ans/Fax mode, attach an answering machine to the
EXT socket on the back of your machine.
When you have finished, press 2 at the Another Page ? prompt.
• If you do not want other people to view your received
documents, you can use secure receiving mode. In this mode,
all of the received faxes are stored in memory. For further
Receiving automatically in Fax mode
Your machine is preset to Fax mode at the factory. When you receive a
fax, the machine answers the call on a specified number of rings and
automatically receives the fax.
Receiving manually in Tel mode
You can receive a fax call by pressing On Hook Dial and then pressing
Start when you hear a fax tone from the remote machine.
9.3
<Faxing>
Download from Www.Somanuals.com. All Manuals Search And Download.
The machine begins receiving a fax and returns to Standby mode when
the reception is completed.
fax machine. Unless you change it, this ringing pattern will continue to be
recognized and answered as a fax call, and all other ringing patterns will
be forwarded to the extension telephone or answering machine plugged
into the EXT socket. You can easily suspend or change DRPD at any
time.
Receiving manually using an extension
telephone
Before using the DRPD option, Distinctive Ring service must be installed
on your telephone line by the telephone company. To set up DRPD, you
will need another telephone line at your location, or someone available to
dial your fax number from outside.
This features works best when you are using an extension telephone
connected to the EXT socket on the back of your machine. You can
receive a fax from someone you are talking to on the extension telephone
without going to the fax machine.
To set up the DRPD mode:
1
2
Press Menu until Fax Setup appears on the top line of the display.
When you receive a call on the extension phone and hear fax tones,
press the keys
fax.
9
on the extension phone. The machine receives the
Press the Scroll buttons until DRPD Mode appears and press
Enter
.
Press the buttons slowly in sequence. If you still hear the fax tone from
the remote machine, try pressing once again.
3
Press the Scroll buttons until Set appears and press Enter.
9
Waiting Ring appears on the display.
9
is the remote receive code preset at the factory. The first and the
last asterisks are fixed, but you can change the middle number to
4
5
Call your fax number from another telephone. It is not necessary to
place the call from a fax machine.
When your machine begins to ring, do not answer the call. The
machine requires several rings to learn the pattern.
Receiving automatically in Ans/Fax mode
When the machine completes learning, the display shows End
To use this mode, you must attach an answering machine to the EXT
socket on the back of your machine.
DRPD [Setup].
If the DRPD setup fails, DRPD Ring Error appears. Press Enter
If the caller leaves a message, the answering machine stores the
message as it would normally. If your machine detects a fax tone on the
line, it automatically starts to receive the fax.
when DRPD Mode appears and start over from step 3.
6
Press Stop/Clear to return to Standby mode.
When the DRPD feature is set up, the DRPD option is available for the
receiving mode setting. To receive faxes in DRPD mode, you need to set
the menu to DRPD.
Notes
• If you have set your machine to Ans/Fax mode and your
answering machine is switched off, or no answering machine is
connected to EXT socket, your machine automatically goes
into Fax mode after a predefined number of rings.
• If your answering machine has a user-selectable ring counter,
set the machine to answer incoming calls within 1 ring.
• If you are in Tel mode (manual reception) when the answering
machine is connected to your machine, you must switch off the
answering machine, or the outgoing message from the
answering machine will interrupt your phone conversation.
Notes
• DRPD must be set up again if you re-assign your fax number,
or connect the machine to another telephone line.
• After DRPD has been set up, call your fax number again to
verify that the machine answers with a fax tone. Then have a
call placed to a different number assigned to that same line to
be sure the call is forwarded to the extension telephone or
answering machine plugged into the EXT socket.
Receiving faxes using DRPD mode
Receiving in secure receiving mode
Distinctive Ring is a telephone company service which enables an user
to use a single telephone line to answer several different telephone
numbers. The particular number someone uses to call you is identified by
different ringing patterns, which consist of various combinations of long
and short ringing sounds. This feature is often used by answering
services who answer telephones for many different clients and need to
know which number someone is calling in on to properly answer the
phone.
You may need to prevent your received faxes from being accessed by
unauthorized people. You can turn on secure receiving mode to restrict
printing of received faxes when the machine is unattended. In secure
receiving mode, all incoming faxes go into memory. When the mode is
deactivated, any stored faxes are printed.
Activating secure receiving mode
Using the Distinctive Ring Pattern Detection (DRPD) feature, your fax
machine can learn the ring pattern you designate to be answered by the
1
Press Menu until Advanced Fax appears on the top line of the
display.
9.4
<Faxing>
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press the Scroll buttons until Secure Receive appears and press
Enter.
Then, as soon as you finish copying or printing, the machine
automatically prints the fax.
3
4
Press the Scroll buttons until On appears and press Enter.
Enter a four-digit password you want to use and press Enter.
Note
You can activate secure receiving mode without setting a
password, but cannot protect your faxes.
5
6
Re-enter the password to confirm it and press Enter.
Press Stop/Clear to return to Standby mode.
When a fax is received in secure receiving mode, your machine stores it
in memory and shows Secure Receive to let you know that there is a fax
received.
Printing received faxes
1
Press Menu until Advanced Fax appears on the top line of the
display.
2
Press the Scroll buttons until Secure Receive appears and press
Enter.
3
4
Press the Scroll buttons until Print appears and press Enter.
Enter the four-digit password and press Enter.
The machine prints all of the faxes stored in memory.
Deactivating secure receiving mode
1
Press Menu until Advanced Fax appears on the top line of the
display.
2
Press the Scroll buttons until Secure Receive appears and press
Enter.
3
4
Press the Scroll buttons until Off appears and press Enter.
Enter the four-digit password and press Enter.
The mode is deactivated and the machine prints all faxes stored in
memory.
5
Press Stop/Clear to return to Standby mode.
Receiving faxes in memory
Since your machine is a multi-tasking device, it can receive faxes while
you are making copies or printing. If you receive a fax while you are
copying or printing, your machine stores incoming faxes in its memory.
9.5
<Faxing>
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
5
Press Menu until Fax Feature appears on the top line of the display.
Other ways to fax
Press Enter when DelayFax appears.
Enter the number of the receiving machine using the number
keypad and press Enter.
Sending a fax to multiple destinations
You can use speed dial numbers, or group dial numbers. For details,
see page 10.3.
You can use the Broadcasting button, which allows you to send a fax to
multiple locations. Originals are automatically stored in memory and sent
to a remote station. After transmission, the originals are automatically
erased from memory.
The display asks you to enter another fax numbers.
6
7
To enter more fax numbers, press 1 to select Yes.
1
Load originals face up into the ADF, or place a single original face
down on the scanner glass.
When you have finished entering fax numbers, press 2 to select No
at the Another Page ? prompt.
8
Enter the job name you want and press Enter.
2
Adjust the document resolution and darkness to suit your fax needs.
If you do not want to assign a name, skip this step.
3
4
Press Broadcasting.
9
Enter the time using the number keypad and press Enter.
Enter the number of the first receiving fax machine and press Enter.
Note
If you set a time earlier than the current time, the fax will be
sent at that time on the following day.
The display asks you to enter another fax number to send the
document.
The original is scanned into memory before transmission. The
display shows memory capacity and the number of pages being
stored in memory.
5
To enter more fax numbers, press 1 and enter another number. You
can add up to 209 destinations.
Note
10 If an original is placed on the scanner glass, load another original
You cannot use group dial numbers for another fax number.
and press 1 to add another page.
When you have finished, press 2 at the Another Page ? prompt.
6
7
When you have finished entering fax numbers, press 2 at the
Another No. prompt.
The machine returns to Standby mode. The display reminds you
that you are in Standby mode and that a delayed fax is set.
The original is scanned into memory before transmission. The
display shows memory capacity and the number of pages being
stored in memory.
Adding pages to a delayed fax
You can add pages to the delayed transmissions previously reserved in
your machine’s memory.
If an original is placed on the scanner glass, load another original
and press 1 to add another pages.
1
2
3
4
Load the originals to be added and adjust document settings.
Press Menu until Fax Feature appears on the top line of the display.
Press the Scroll buttons until Add Page appears and press Enter.
When you have finished, press 2 at the Another Page ? prompt.
The machine begins sending the fax to the numbers you entered in
the order in which you entered them.
Press the Scroll buttons until the fax job you want appears and
press Enter.
Sending a delayed fax
5
If an original is placed on the scanner glass, load another original
and press 1 to add another page.
You can set your machine to send a fax at a later time when you will not
be present.
When you have finished, press 2 at the Another Page ? prompt.
1
Load originals face up into the ADF, or place a single original face
down on the scanner glass.
The machine scans the original into memory and shows the total
number of pages and the number of the added pages.
2
Adjust the document resolution and darkness to suit your fax needs.
9.6
<Faxing>
Download from Www.Somanuals.com. All Manuals Search And Download.
Canceling a delayed fax
1
2
3
Press Menu until Fax Feature appears on the top line of the display.
Press the Scroll buttons until Cancel Job appears and press Enter.
Press the Scroll buttons until the fax job you want appears and
press Enter.
4
Press 1 to select Yes.
The selected fax job is deleted from memory.
Sending a priority fax
Using the Priority Fax feature, a high priority fax can be sent ahead of
reserved operations. The original is scanned into memory and
immediately transmitted when the current operation is finished. In
addition, priority transmission will interrupt a broadcasting operation
between stations (i.e., when the transmission to station A ends, before
transmission to station B begins) or between redial attempts.
1
Load originals face up into the ADF, or place a single original face
down on the scanner glass.
2
Adjust the document resolution and darkness to suit your fax needs.
3
4
Press Menu until Fax Feature appears on the top line of the display.
Press the Scroll buttons until Priority Fax appears and press
Enter.
5
6
Enter the number of the receiving machine using the number
keypad and press Enter.
Enter the job name you want and press Enter.
The original is scanned into memory before transmission. The
display shows memory capacity and the number of pages being
stored in memory.
7
If an original is placed on the scanner glass, load another original
and press 1 to add another page.
When you have finished, press 2 at the Another Page ? prompt.
The machine shows the number being dialed and begins sending
the fax.
9.7
<Faxing>
Download from Www.Somanuals.com. All Manuals Search And Download.
Option
Redials
Description
10 Fax setup
You can specify the number of redial attempts. If you
enter 0, the machine will not redial.
This chapter gives you information on setting up your machine for
receiving and sending faxes.
MSG
Confirm
You can set your machine to print a report showing
whether a transmission was successful, how many
pages were sent, and more. The available options
are On, Off, and On-Err, which prints only when a
transmission is not successful.
This chapter includes:
•
•
•
•
•
Auto
Report
This produces a report with detailed information
about the previous 50 communications operations,
including time and dates. The available options are
On or Off.
Auto
Reduction
When receiving a fax containing pages as long as or
longer than the paper loaded in the paper tray, the
machine can reduce the size of the original to fit the
size of the paper loaded in the machine. Turn on this
feature if you want to automatically reduce an
incoming page.
Changing the fax setup options
Your machine provides you with various user-selectable options for
setting up the fax system. You can change the default settings for your
preferences and needs.
To change the fax setup options:
With this feature set to Off, the machine cannot
reduce the original to fit onto one page. The original
will be divided and printed in actual size on two or
more pages.
1
2
Press Menu until Fax Setup appears on the top line of the display.
Press the Scroll buttons until the menu item you want appears and
press Enter.
Discard
Size
When receiving a fax containing pages as long as or
longer than the paper in your machine, you can set
the machine to discard a specific length from the end
of the received fax. The machine will print the
received fax on one or more sheets of paper, except
the data that would have been on the specified
discard segment.
3
Press the Scroll buttons until the desired status appears or enter
the value for the option you have selected, and press Enter.
4
5
If necessary, repeat steps 2 through 3.
Press Stop/Clear to return to Standby mode.
When the received fax contains pages larger than the
paper in your machine, and Auto Reduction has
been turned on, the machine will reduce the fax to fit
on the existing paper, and nothing will be discarded.
Fax setup options
Option
Description
RCV Start
Code
This code allows you to initiate fax reception from an
extension phone plugged into the EXT socket on the
back of the machine. If you pick up the extension
phone and hear fax tones, enter the code. It is preset
Receive
Mode
You can select the default fax receiving mode. For
details on receiving faxes in each mode, see page
9.3.
to
9
at the factory.
Ring to
Answer
You can specify the number of times the machine
rings before answering an incoming call.
DRPD
Mode
This mode enables a user to use a single telephone
line to answer several different telephone numbers.
In this menu, you can set the machine to recognize
which ring patterns to answer. For details about this
1
Darkness
You can select the default contrast mode to fax your
documents lighter or darker.
• Light works well with dark print.
• Normal works well with standard typed or printed
documents.
1.Distinctive Ring Pattern Detection
• Dark works well with light print or faint pencil
markings.
Redial Term Your machine can automatically redial a remote fax
machine if it was busy. You can set an interval
between attempts.
10.1
<
Fax setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the advanced fax features
Printing sent fax report automatically
To use the advanced fax options:
You can set the machine to print a report with detailed information about
the previous 50 communication operations, including time and dates.
1
2
3
Press Menu until Advanced Fax appears on the top line of the
display.
1
2
Press Menu until Fax Setup appears on the top line of the display.
Press the Scroll buttons until the menu item you want appears and
press Enter.
Press the Scroll buttons until Auto Report appears and press
Enter.
Press the Scroll buttons until the desired status appears or enter
3
4
Press the Scroll buttons until On appears and press Enter.
the value for the option you have selected, and press Enter.
Press Stop/Clear to return to Standby mode.
4
5
If necessary, repeat steps 2 through 3.
Press Stop/Clear to return to Standby mode.
Using the toll save mode
Advanced fax options
You can set your machine to send the original stored in the memory
during preset time slots, when call charges are lower. This toll save mode
helps you to take advantage of lower long distance rates.
Option
Description
1
Press Menu until Advanced Fax appears on the top line of the
display.
Toll Save
You can set you machine to store your faxes into
the memory and send them at the specified toll-
saving time. For further details about setting this
mode, see the next column.
2
3
4
5
6
7
Press Enter when Toll Save appears.
Press Enter when Start Time appears.
Junk Fax Setup Using this feature, the system will not accept
faxes sent from remote stations whose numbers
are stored in the memory as junk fax numbers.
This feature is useful for blocking any unwanted
faxes.
Enter the starting time and press Enter.
Press the Scroll buttons until End Time appears and press Enter.
Enter the ending time and press Enter.
When you turn on this feature, you can access
the following options to set junk fax numbers.
Press Stop/Clear to return to Standby mode.
• Setup: allows you to set up to 10 fax numbers.
• All Delete: allows you to delete all junk fax
numbers.
Subsequent sent faxes will be stored into the memory and be sent
at the preset time.
Secure Receive You can keep your received faxes from being
accessed by unauthorized people. For further
details about setting this mode, see page 9.4.
Prefix Dial
You can set a prefix of up to five digits. This
number dials before any automatic dial number is
started. It is useful for accessing a PABX
exchange.
Stamp RCV
Name
This option allows the machine to automatically
print the page number, and the date and time of
reception at the bottom of each page of a
received fax.
1
ECM Mode
This mode helps with poor line quality and makes
sure any faxes you send are sent smoothly to any
other ECM-equipped fax machine. Sending a fax
using ECM may take more time.
1. Error Correction Mode
10.2
<
Fax setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
Group dial numbers
Setting up Phone Book
If you frequently send the same document to several destinations, you
can group these destinations and set them under a group dial number.
You can then use a group dial number to send a document to all of the
destinations within the group. You can set up to 199 group dial numbers
using the destination’s existing speed dial numbers.
You can set up Phone Book with the fax numbers you use most
frequently. Your machine provides you with the following features for
setting up Phone Book:
• Speed dial numbers
• Group dial numbers
Registering a group dial number
1
Press Phone Book until Store/Edit appears on the bottom line of
the display and press Enter.
Speed dial numbers
You can store up to 200 frequently-used fax numbers in speed dial
numbers.
2
Press the Scroll buttons until Group Dials appears and press
Enter.
Registering a speed dial number
3
4
5
6
7
Press Enter when New appears.
1
Press Phone Book until Store/Edit appears on the bottom line of
Enter a group dial number between 0 and 199 and press Enter.
Enter a speed dial number and press Enter.
Press Enter.
the display and press Enter.
2
3
Press Enter when Speed Dials appears.
Enter a speed dial number between 0 and 199 and press Enter.
Repeat steps 5 and 6 to include other speed dial numbers into the
group.
If an entry is already stored in the number you choose, you can edit
the entry. To start over with another speed dial number, press Upper
Level.
8
9
When you have finished, press Upper Level.
4
5
Enter the fax number you want and press Enter.
Enter the group name you want and press Enter.
Enter the name you want and press Enter.
10 Press Stop/Clear to return to Standby mode.
Editing a group dial number
6
Press Stop/Clear to return to Standby mode.
You can delete a specific entry from a group or add a new number to the
selected group.
Editing speed dial numbers
1
Press Phone Book until Store/Edit appears on the bottom line of
the display and press Enter.
1
Press Phone Book until Store/Edit appears on the bottom line of
the display and press Enter.
2
Press the Scroll buttons until Group Dials appears and press
Enter.
2
3
4
5
6
Press Enter when Speed Dials appears.
Enter the speed dial number you want to edit and press Enter.
Change the fax number and press Enter.
Change the name and press Enter.
3
4
5
Press the Scroll buttons until Edit appears and press Enter.
Enter the group dial number you want to edit and press Enter.
Enter the speed dial number you want to add or delete and press
Enter.
Press Stop/Clear to return to Standby mode.
If you enter a new speed dial number, Add? appears.
Using speed dial numbers
If you enter a speed dial number stored in the group, Delete?
appears.
When you are prompted to enter a destination number while sending a
fax, enter the speed dial number at which you stored the number you
want.
6
7
8
9
Press Enter to add or delete the number.
Repeat from step 5 to add or delete more numbers.
When you have finished, press Upper Level.
Edit the group name and press Enter.
• For a one-digit (0-9) speed dial number, press and hold the
corresponding digit button on the number keypad.
• For a two- or three-digit speed dial number, press the first digit
button(s) and then hold down the last digit button.
10 Press Stop/Clear to return to Standby mode.
10.3
<
Fax setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
Using group dial numbers
When you are prompted to enter a destination number while sending a
fax, enter the group dial number at which you stored the number you
want.
• For a one-digit (0-9) group dial number, press and hold the
corresponding digit button on the number keypad.
• For a two- or three-digit group dial number, press the first digit
button(s) and then hold down the last digit button.
Searching Phone Book for an entry
You can search for a number in memory.
1
Press Phone Book until Search&Dial appears on the bottom line of
the display and press Enter.
2
Press the Scroll buttons until the name and number you want
appears and press Enter.
The machine dials to the selected number.
Printing Phone Book
You can check your Phone Book settings by printing a list.
1
Press Phone Book until Print appears on the bottom line of the
display.
2
Press Enter. A list showing speed dial and group dial entries prints
out.
10.4
<
Fax setup>
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Ordering supplies and
accessories
This chapter provides information on purchasing toner cartridge available
for your machine.
Toner cartridges
When the toner runs out, you can order the following types of toner
cartridge for your machine:
1
Type
Average Yield
Part number
High yield
3,000 Standard pages
SCX-D4725A
1. Declared yield value in accordance with ISO/IEC 19752.
How to purchase
To order Samsung-authorized supplies or accessories, contact your local
Samsung dealer or the retailer where you purchased your machine, or
information on calling for technical support.
11.1
<
Ordering supplies and accesso-
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing a report
12 Maintenance
1
2
Press Menu until Reports appears on the top line of the display.
This chapter provides information for maintaining your machine and the
toner cartridge.
Press the Scroll buttons until the report or list you want to print
appears and press Enter.
This chapter includes:
The selected information prints out.
•
•
•
•
•
•
•
Other available reports
Your machine prints the following reports automatically.
• Multi-communication Report: prints automatically after sending
faxes for more than one location.
• Power Failure Report: prints out automatically when power is
restored after a power failure if any data loss occurs due to the power
failure.
Printing reports
Clearing memory
Your machine can provide various reports with useful information you will
need. The following reports are available:
You can selectively clear information stored in your machine’s memory.
Caution
Report/List
Description
Before clearing the memory, make sure that all fax jobs have
been completed, or you will lose those jobs.
Phone Book
This list shows all of the fax numbers stored in
the machine’s memory.
1
2
3
Press Menu until Maintenance appears on the top line of the
display.
Sent Report
This report shows information on the faxes you
have recently sent.
Press the Scroll buttons until Clear Memory appears and press
Enter.
You can set the machine to automatically print
this report every 50 communications. See
page 10.2.
Press the Scroll buttons until the item you want to clear appears
and press Enter.
RCV Report
System Data
This report shows information on the faxes you
have recently received.
Options
Description
This list shows the status of the user-selectable
options. You may print this list to confirm your
changes after changing any settings.
All Settings
Clears all of the data stored in memory and
resets all of your settings to the factory default.
Paper Setting Restores all of the paper settings to the factory
Scheduled
Jobs
This list shows the documents currently stored
for delayed faxes along with the starting time and
type of each operation.
default.
Copy Setup
Fax Setup
Restores all of the copy options to the factory
default.
MSG Confirm
This report shows the fax number, the number of
pages, the elapsed time of the job, the
communication mode, and the communication
results for a particular fax job.You can set up your
machine to automatically print a message
confirmation report after each fax job.
Restores all of the fax options to the factory
default.
Fax Feature
Cancels all of the scheduled fax jobs in the
machine’s memory.
Junk Fax List
This list shows the fax numbers specified as junk
fax numbers. To add or delete numbers to or
from this list, access the Junk Fax Setup menu.
Advanced Fax Restores all of the advanced fax options to the
factory default.
Sent Report
RCV Report
Clears all records of sent faxes.
Clears all records of received faxes.
12.1
<
Maintenance>
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
Description
Cautions
• To prevent damage to the toner cartridge, do not expose it to
light for more than a few minutes. Cover it with a piece of
paper, if necessary.
Phone Book
Clears all of the fax numbers stored in
memory.
• Do not touch the green surface underside of the toner
cartridge. Use the handle on the cartridge to avoid touching
this area.
4
5
Repeat step 3 to clear another item.
Press Stop/Clear to return to Standby mode.
3
Pull the manual tray out.
Cleaning your machine
To maintain print and scan quality, follow the cleaning procedures below
each time the toner cartridge is replaced or if print and scan quality
problems occur.
Caution
Cleaning the cabinet of the machine with cleaning materials
containing large amounts of alcohol, solvent, or other strong
substances can discolor or distort the cabinet.
Cleaning the outside
Clean the cabinet of the machine with a soft lint-free cloth. You can
dampen the cloth slightly with water, but be careful not to let any water
drip onto or into the machine.
Cleaning the inside
4
With a dry lint-free cloth, wipe away any dust and spilled toner from
the toner cartridge area and the toner cartridge cavity.
During the printing process, paper, toner, and dust particles can
accumulate inside the machine. This buildup can cause print quality
problems, such as toner specks or smearing. Cleaning the inside of the
machine clears or reduces these problems.
1
Turn the machine off and unplug the power cord. Wait for the
machine to cool down.
2
Open the front cover and pull the toner cartridge out. Set it on a
clean flat surface.
Caution
While cleaning the inside of the machine, be careful not to touch
the transfer roller, located underneath the toner cartridge. Oil
from your fingers can cause print scan quality problems.
12.2
<
Maintenance>
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Locate the long strip of glass (LSU) inside the top of the cartridge
compartment, and gently swab the glass to see if dirt turns the white
cotton black.
3
Wipe the surface of the scanner glass and ADF glass until it is clean
and dry.
1
3
2
4
6
Push the manual tray back into the machine.
white sheet
ADF glass
1
2
3
4
scanner lid
scanner glass
4
5
Wipe the underside of the scanner lid and white sheet until it is
clean and dry.
Close the scanner lid.
Maintaining the toner cartridge
7
8
Reinsert the toner cartridge and close the front cover.
Plug in the power cord and turn the machine on.
Toner cartridge storage
To get the most from the toner cartridge, keep the following guidelines in
mind:
Cleaning the scan unit
• Do not remove the toner cartridge from its package until ready for use.
Keeping the scan unit clean helps ensure the best possible copies. We
suggest that you clean the scan unit at the start of each day and during
the day, as needed.
• Do not refill the toner cartridge. The machine warranty does not cover
damage caused by using a refilled cartridge.
• Store toner cartridges in the same environment as your machine.
1
2
Slightly dampen a soft lint-free cloth or paper towel with water.
Open the scanner lid.
• To prevent damage to the toner cartridge, do not expose it to light for
more than a few minutes.
Expected cartridge yield
The toner cartridge yield depends on the amount of toner that print jobs
require. Average yield for a new toner cartridge is 3,000 standard pages in
accordance with ISO/IEC 19752 standard. (Average yield for the original
toner cartridge supplied with the machine is 1,500 standard pages.)
The actual number may also be different depending on the print density of
the pages you print on, and the number of pages may be affected by
operating environment, printing interval, media type, and media size. If you
print a lot of graphics, you may need to change the cartridge more often.
12.3
<
Maintenance>
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Hold the toner cartridge by the handle and slowly insert the cartridge
into the opening in the machine.
Redistributing toner
When the toner cartridge is near the end of its life:
• White streaks or light printing occurs.
• Toner Low appears on the display.
Tabs on the sides of the cartridge and corresponding grooves within
the machine will guide the cartridge into the correct position until it
locks into place completely.
If this happens, you can temporarily reestablish print quality by
redistributing the remaining toner in the cartridge. In some cases, white
streaks or light printing will still occur even after you have redistributed the
toner.
1
2
Open the front cover.
Pull the toner cartridge out.
5
Close the front cover. Make sure that the cover is securely closed.
3
Thoroughly roll the cartridge 5 or 6 times to distribute the toner
evenly inside the cartridge.
Note
Replacing the toner cartridge
If toner gets on your clothing, wipe it off with a dry cloth and
wash clothing in cold water. Hot water sets toner into fabric.
When the toner cartridge is completely empty:
• Toner Empty Replace Toner appears on the display.
• The machine stops printing. Incoming faxes are saved in memory.
Caution
Do not touch the green underside of the toner cartridge.
Use the handle on the cartridge to avoid touching this area.
At this stage, the toner cartridge needs to be replaced. For order
12.4
<
Maintenance>
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Cleaning the drum
You can set the machine to disregard the Toner Empty
Replace Toner message and to continue printing. See page
If there are streaks or spots on your print, the OPC drum of the toner
cartridge may require cleaning.
1
Before starting the cleaning procedure, make sure that paper is
loaded in the machine.
1
2
Open the front cover.
Pull the toner cartridge out.
2
Press Menu until Maintenance appears on the top line of the
display.
3
4
Press Enter when Clean Drum appears.
Press Enter when Yes appears.
The machine prints out a cleaning page. Toner particles on the drum
surface are affixed to the paper.
If the problem remains, repeat steps 1 through 4.
Cleaning the drum automatically
You can set your machine to print a cleaning page automatically every
600 pages.
1
Press Menu until Maintenance appears on the top line of the
display.
2
Press the Scroll buttons until Auto Cleaning appears and press
Enter.
3
4
Remove the new toner cartridge from its bag.
3
4
Press the Scroll buttons until On appears and press Enter.
Remove the packing tape and roll the cartridge 5 or 6 items to
distribute the toner.
Press Stop/Clear to return to Standby mode.
Sending new toner notification
You can set your machine to automatically send a fax to your service
company or dealer to notify them that your machine requires a new toner
cartridge when the toner cartridge needs to be replaced. The fax number
needs to be set by your dealer prior to using this feature, otherwise the
machine cannot send a notification even though you turn this service on.
1
Press Menu until Maintenance appears on the top line of the
display.
Thoroughly roll the cartridge to assure maximum copies per
cartridge. Save the box and the plastic bag for shipping.
2
Press the Scroll buttons until Notify Toner appears and press
Enter.
Note
If toner gets on your clothing, wipe it off with a dry cloth and
wash clothing in cold water. Hot water sets toner into fabric.
3
4
Press the Scroll buttons until On appears and press Enter.
Caution
Press Stop/Clear to return to Standby mode.
Do not touch the green underside of the toner cartridge.
Use the handle on the cartridge to avoid touching this area.
5
6
Hold the toner cartridge by the handle and slowly insert the cartridge
into the opening in the machine.
Tabs on the sides of the cartridge and corresponding grooves within
the machine will guide the cartridge into the correct position until it
locks into place completely.
Close the front cover. Make sure that the cover is securely closed.
12.5
<
Maintenance>
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing continuously when the Toner Empty
Replace Toner message appears
Maintenance parts
To avoid print quality and paper feed problems resulting from worn parts
and to maintain your printer in top working condition, the following items
will need to be replaced at the specified number of pages or when the life
span of each item has expired.
When the toner cartridge is nearly empty, the machine shows the Toner
Empty Replace Toner message and stops printing. You can set the
machine to disregard this message when it appears and to continue
printing, even though print quality is not optimal.
Items
ADF rubber pad
Yield (Average)
Approx. 20,000 pages
Approx. 50,000 pages
Approx. 50,000 pages
Approx. 50,000 pages
1
2
3
Press Menu until Machine Setup appears on the top line of the
display.
Press the Scroll buttons until Ignore Toner appears and press
Enter.
Transfer roller
Fuser unit
Press the Scroll buttons until On appears and press Enter.
If you select Off, the received fax cannot be printed until you install
a new toner cartridge. However, faxes can be received into memory
as long as it allows.
Pickup roller
Samsung highly recommends that an authorized service provider, dealer
or the retailer where you bought printer performs this maintenance
activity.
4
Press Stop/Clear to return to Standby mode.
Replacing the ADF rubber pad
Clearing the Toner Empty Replace Toner
message
You will need to replace the ADF rubber pad when there seems to be a
consistent problem with paper pickup or when its specified yield is
reached.
When the Toner Empty Replace Toner message appears you can
configure not to see this message again not to disturb you.
1
2
Open the ADF cover.
1
2
Press Menu until Maintenance appears on the top line of the
display.
Remove the ADF rubber pad from the ADF, as shown.
Press the Scroll buttons until CLR Empty Msg. appears and press
1
Enter.
3
4
Press the Scroll buttons until On appears and press Enter.
Now the Toner Empty Replace Toner message does not appear
but the Replace Toner message will remain for reminding you that
the new cartridge needs to be installed for quality.
Caution
Once you have selected On, this setting will be permanently
written to the memory of the toner cartridge, and this menu will
be disappeared from the Maintenance menu.
ADF rubber pad
1
3
4
Insert a new ADF rubber pad into place.
Close the ADF cover.
12.6
<
Maintenance>
Download from Www.Somanuals.com. All Manuals Search And Download.
Managing your machine from the website
(SCX-4725FN only)
If you have connected your machine to a network and set up TCP/IP
network parameters correctly, you can manage the machine via
Samsung’s SyncThru™ Web Service, an embedded web server. Use
SyncThru™ Web Service to:
• View the machine’s device information and check its current status.
• Change TCP/IP parameters and set up other network parameters.
• Change the printer properties.
• Set the machine to send email notifications to let you know the
machine’s status.
• Get support for using the machine.
To access SyncThru™ Web Service:
1
2
Start a web browser, such as Internet Explorer, from Windows.
Enter the machine IP address (http://xxx.xxx.xxx.xxx) in the address
field and press the Enter key or click Go.
Your machine’s embedded website opens.
12.7
<
Maintenance>
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
See the next section.
13 Troubleshooting
This chapter gives helpful information for what to do if you encounter an
error.
4
Close the ADF cover. Then load the removed pages, if any, back into
the ADF.
This chapter includes:
Note
•
•
•
•
•
To prevent document jams, use the scanner glass for thick, thin, or
mixed paper-type originals.
Exit Misfeed
1
2
3
Remove any remaining pages from the ADF.
Open the ADF cover.
Clearing document jams
Pull the jammed paper gently out of the document output tray.
When an original jams while passing through the ADF, Document Jam
appears on the display.
Input Misfeed
1
2
Remove any remaining pages from the ADF.
Open the ADF cover.
1
4
Close the ADF cover. Then load the removed pages, if any, back into
the ADF.
ADF cover
1
Clearing paper jams
When a paper jam occurs, Paper Jam appears on the display. Refer to the
table below to locate and clear the paper jam.
3
Pull the jammed paper gently out of the ADF.
Message
Location of jam
Go to
[Paper Jam 0]
Open/Close Door
In the paper feed area (tray or
manual tray)
the next
sectionand
page 13.2
[Paper Jam 1]
Open/Close Door
toner cartridge
[Paper Jam 2]
Check Inside
In the paper exit area
page 13.2
13.1
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
In the fuser area or around the toner cartridge
To avoid tearing the paper, pull out the jammed paper gently
and slowly. Follow the instructions in the following sections to
clear the jam.
Note
The fuser area is hot. Take care when removing paper from the
machine.
In the tray
1
2
3
Open the front cover and pull the toner cartridge out.
If necessary, pull the manual tray out.
1
Open and close the front cover. The jammed paper is automatically
ejected from the machine.
Remove the jammed paper by gently pulling it straight out.
If the paper does not exit, go to the next step.
2
Remove the jammed paper by gently pulling it straight out.
4
5
If necessary, push the manual tray back into the machine.
Replace the toner cartridge and close the front cover. Printing
automatically resumes.
If the paper does not move when you pull, or if you do not see the
paper in this area, check the fuser area around the toner cartridge.
See page 13.2.
In the paper exit area
3
Open and close the front cover to resume printing.
1
Open and close the front cover. The jammed paper is automatically
ejected from the machine.
In the manual tray
If the paper does not exit, go to the next step.
Gently pull the paper out of the output tray.
1
If the paper is not feeding properly, pull the paper out of the
machine.
2
If you do not see the jammed paper or if there is any resistance
when you pull, stop and go to the next step.
2
Open and close the front cover to resume printing.
13.2
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Open the rear cover.
Tips for avoiding paper jams
By selecting the correct media types, most paper jams can be avoided.
are positioned correctly.
• Do not overload the tray.
• Do not remove paper from the tray while your machine is printing.
• Flex, fan, and straighten paper before loading.
• Do not use creased, damp, or highly curled paper.
• Do not mix paper types in a tray.
.
• Ensure that the recommended print side of print media is facing up in the
tray or manual tray.
4
Pull the jammed paper out.
Understanding display messages
Messages appear on the Smart Panel program window or the control panel
display to indicate the machine’s status or errors. Refer to the tables below
to understand the messages’ meaning and correct the problem if necessary.
Messages and their meanings are listed in alphabetical order.
Note
When you call for service, it is very convenient to tell the service
representative the display message.
Message
Meaning
Suggested solutions
[COMM. Error]
The machine has a
communication
problem.
Ask the sender to try
again.
Caution
[Front or Rear]
[Cover Open]
The front cover or
rear cover is not
securely latched.
Close the cover until it
locks into place.
Inside of the machine is very hot. Take care when removing paper
from the machine.
5
Close the rear cover. Printing automatically resumes.
[Hsync Error]
There is a serious
problem in your
machine.
Turn the machine off and
back on. If the problem
persists, please call for
service.
[Incompatible]
The machine has
received a fax from
which is registered
as a junk fax.
The received fax data will
be deleted.
Reconfirm junk fax setup,
see page 10.2.
[Line Error]
Your machine
Try again. If the problem
persists, wait an hour or
so for the line to clear
and try again.
cannot connect with
the receiving fax
machine or has lost
contact because of a
problem with the
phone line.
Or, turn the ECM mode
13.3
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Meaning
Suggested solutions
Message
Cancel?
Meaning
Suggested solutions
[Low Heat Error]
There is a problem
in the fuser unit.
Unplug the power cord
and plug it back in. If the
problem persists, please
call for service.
Your machine’s
memory has
become full while
trying to store an
original into memory.
To cancel the fax job,
press 1 to select Yes.
1:Yes 2:No
If you want to send those
pages that have been
successfully stored,
press 2 to select No. You
should send the
remaining pages later,
when memory is
available.
[LSU Error]
[No Answer]
A problem has
occurred in the LSU and plug it back in. If the
(Laser Scanning
Unit).
Unplug the power cord
problem persists, please
call for service.
The receiving fax
machine has not
answered after
several redial
attempts.
Try again. Make sure that
the receiving machine is
operational.
Document Jam
Enter Again
The loaded original
has jammed in the
ADF.
Clear the jam. See page
You entered an
unavailable data.
Enter the correct data
again.
[No Paper]
Add Paper
The paper in the tray Load paper in the tray.
has run out.
See page 5.5.
Group Not
Available
You have tried to
select a group dial
number where only
a single location
number can be
used.
Use a speed dial number
or dial a number
manually using the
number keypad.
[Over Heat]
There is a problem
in the fuser unit.
Unplug the power cord
and plug it back in. If the
problem persists, please
call for service.
Open Heat Error
There is a problem
in the fuser unit.
Unplug the power cord
and plug it back in. If the
problem persists, please
call for service.
Line Busy
The receiving fax
machine did not
answer or the line is
already engaged.
Try again after a few
minutes.
[Paper Jam 0]
Open/Close Door
Paper has jammed
in the feeding area
of the tray.
Clear the jam. See page
Load Document
You have attempted Load a document into the
to set up a copy or
fax operation with no
document loaded
into the ADF.
ADF and try again.
[Paper Jam 1]
Open/Close Door
Paper has jammed
in the fuser area.
Clear the jam. See page
[Paper Jam 2]
Check Inside
Paper has jammed
in the paper exit
area.
Clear the jam. See page
Memory Dial Full
Memory Full
The fax jobs queue
in the memory is full. jobs in the memory.
Cancel unnecessary fax
The memory is full.
Delete unnecessary fax
jobs and retransmit after
more memory becomes
available. Alternatively,
split the transmission into
more than one operation.
[Stop Pressed]
Stop/Clear has
been pressed during
a fax transmission.
Try again.
Add Paper &
Press Start
You have selected
Manual Feeder for
Load a sheet of paper
into the manual tray and
Source in the printer press Start to start
Not Assigned
The speed dial
Enter the number
manually using the
number keypad.
properties.
feeding.
number you tried to
use has no number
assigned to it.
If you have multiple
pages to be printed, this
message appears again.
Load the next sheet and
press Start.
Operation Not
Assigned
You are in the Add
Page/Cancel Job
operation, but there
are no jobs stored.
Check the display to see
if there are any
scheduled jobs.
13.4
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Message
Meaning
Suggested solutions
Message
Meaning
Suggested solutions
Power Failure
Power has turned off The job which you were
Toner Empty
The toner in the
cartridge has run
out.
Install a new genuine
toner cartridge.
then on and the
machine’s memory
has not been back
up.
trying to do before the
power failure must be
completely re-done.
Replace Toner
You can keep printing but
the quality cannot be
guaranteed, and the
product support is no
longer provided.
Retry Redial?
The machine is
waiting for a
specified time
interval to redial a
previously busy
station.
You can press Enter to
immediately redial, or
Stop/Clear to cancel the
redial operation.
You can configure not to
see the Toner Empty
Replace Toner
message.
Toner Exhausted
Replace Toner
The lifespan of the
toner cartridge is
reached.
Install the genuine toner
cartridge.
Scanner locked
The scanner module Unlock the scanner and
is locked. press Stop/Clear.
Unavailable
Date & Time
The current date and Enter the correct date
Toner Low
The toner cartridge
is almost empty.
Take out the toner
cartridge and thoroughly
shake it. By doing this,
you can temporarily
reestablish printing
operations.
time you entered is
not correct.
and time.
Toner cartridge-related messages
Message
Meaning
Suggested solutions
Solving other problems
Install Toner
Invalid Toner
A toner cartridge is
not installed.
Install a toner cartridge.
The following chart lists some conditions that may occur and the
recommended solutions. Follow the suggested solutions until the problem is
corrected. If the problem persists, please call for service.
The toner cartridge
you have installed in genuine toner cartridge,
Install a Samsung-
not for your
machine.
designed for your
machine.
Paper feeding problems
NonGenuine Toner The toner cartridge
Install the genuine toner
cartridge.
Condition
Suggested solutions
installed is not a
Replace Toner
Paper is jammed
during printing.
genuine cartridge.
Replace Toner
The toner in the
cartridge has run
out.
This message appears
when you turned off the
Toner Empty Replace
Toner message.
Paper sticks
together.
• Ensure that there is not too much paper in the tray.
The tray can hold up to 250 sheets of paper,
depending on the thickness of your paper.
• Make sure that you are using the correct type of
• Remove paper from the tray and flex or fan the
paper.
• Humid conditions may cause some paper to stick
together.
Install a new genuine
toner cartridge.
You can keep printing but
the quality cannot be
guaranteed, and the
product support is no
longer provided.
Multiple sheets of • Different types of paper may be stacked in the tray.
paper do not
feed.
Load paper of only one type, size, and weight.
• If multiple sheets have caused a paper jam, clear
the paper jam. See page 13.1.
13.5
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing problems
Condition
Suggested solutions
Paper does not
feed into the
machine.
• Remove any obstructions from inside the machine.
• Paper has not been loaded correctly. Remove
paper from the tray and reload it correctly.
• There is too much paper in the tray. Remove
excess paper from the tray.
• The paper is too thick. Use only paper that meets
the specifications required by the machine. See
Condition
Possible cause
Suggested solutions
The
The machine is not
receiving power.
Check the power cord
connections. Check the
power switch and the power
source.
machine
does not
print.
The machine is not
selected as the
default printer.
Select Samsung SCX-4725
Series PCL 6 as your default
printer in your Windows.
• If an original does not feed into the machine, the
ADF rubber pad may require to be replaced. See
page 12.6.
Check the machine for the following:
• The front cover is not closed. Close the cover.
• Paper is jammed. Clear the paper jam. See
page 13.1.
• The toner cartridge is not installed. Install the toner
cartridge.
The paper keeps
jamming.
• There is too much paper in the tray. Remove
excess paper from the tray. If you are printing on
special materials, use the manual tray.
• An incorrect type of paper is being used. Use only
paper that meets the specifications required by the
If a system error occurs, contact your service
representative.
• There may be debris inside the machine. Open the
front cover and remove the debris.
• If an original does not feed into the machine, the
ADF rubber pad may require to be replaced. See
page 12.6.
The connection cable
between the
computer and the
machine is not
Disconnect the printer cable
and reconnect it.
Transparencies
stick together in
the paper exit.
Use only transparencies specifically designed for
laser printers. Remove each transparency as it exits
from the machine.
connected properly.
The connection cable
between the
computer and the
machine is defective.
If possible, attach the cable
to another computer that is
working properly and print a
job. You can also try using a
different printer cable.
Envelopes skew
or fail to feed
correctly.
Ensure that the paper guides are against both sides
of the envelopes.
The port setting is
incorrect.
Check the Windows printer
setting to make sure that the
print job is sent to the correct
port. If the computer has
more than one port, make
sure that the machine is
attached to the correct one.
The machine may be
configured
incorrectly.
Check the printer properties
to ensure that all of the print
settings are correct.
The printer driver
may be incorrectly
installed.
Repair the printer software.
See the Software Section
.
The machine is
malfunctioning.
Check the display message
on the control panel to see if
the machine is indicating any
system errors.
13.6
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Condition
Possible cause
Suggested solutions
Condition
Possible cause
Suggested solutions
The
machine
selectsprint printer properties
materials
from the
wrong
paper
source.
The paper source
selection in the
For many software
The
The printer cable is
loose or defective.
Disconnect the printer cable
and reconnect. Try a print job
that you have already printed
successfully. If possible,
attach the cable and the
machine to another computer
and try a print job that you
know works. Finally, try a
new printer cable.
applications, the paper
source selection is found
under the Paper tab within
the printer properties. Select
the correct paper source.
See the printer driver help
screen.
machine
prints, but
the text is
wrong,
garbled, or
incomplete.
may be incorrect.
A print job
isextremely complex.
slow.
The job may be very
Reduce the complexity of the
page or try adjusting the print
quality settings.
The wrong printer
driver was selected.
Check the application’s
printer selection menu to
ensure that your machine is
selected.
If you are using
Windows 98/Me, the
From the Start menu, choose
Settings and then Printers.
Spool Setting may be Right-click the Samsung
The software
application is
malfunctioning.
Try printing a job from
another application.
set incorrectly.
SCX-4725 Series PCL 6
machine icon, choose
Properties, click the Details
tab, and then choose the
Spool Settings button.
Select the desired spool
setting.
The operating system Exit Windows and reboot the
is malfunctioning.
computer. Turn the machine
off and then back on again.
Pagesprint, The toner cartridge is Redistribute the toner, if
but are
blank.
defective or out of
toner.
necessary. See page 12.4.
Half the
page is
blank.
The page orientation
setting may be
incorrect.
Change the page orientation
in your application. See the
printer driver help screen.
If necessary, replace the
toner cartridge.
The paper size and
the paper size
settings do not
match.
Ensure that the paper size in
the printer driver settings
matches the paper in the
tray.
The file may have
blank pages.
Check the file to ensure that
it does not contain blank
pages.
Some parts, such as
the controller or the
board, may be
Contact a service
representative.
Or, ensure that the paper
size in the printer driver
settings matches the paper
selection in the software
application settings you use.
defective.
The
The setting in the
illustrations software application
Select Download as
Bitmap in the TrueType
Options window of the
graphic properties and print
the document again.
print
is wrong.
incorrectly
in Adobe
Illustrator.
The printer
does not
print PDF
file correctly. products.
Some parts
of graphics,
Incompatibility
between the PDF file
and the Acrobat
Printing the PDF file as an
image may solve this problem.
Turn on Print as Image from
the Acrobat printing options.
Note: It will take longer to print
when you print a PDF file as
an image.
text or
illustrations
are missing.
13.7
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing quality problems
Condition
Suggested solutions
If the inside of the machine is dirty or paper has been loaded improperly, you
may notice a reduction in print quality. See the table below to clear the
problem.
Vertical lines
If black vertical streaks appear on the page:
• The drum inside the toner cartridge has
probably been scratched. Remove the toner
cartridge and install a new one. See
page 12.4.
Condition
Suggested solutions
Light or faded print If a vertical white streak or faded area appears
If white vertical streaks appear on the page:
on the page:
• The surface of the LSU part inside the
machine may be dirty. Clean the LSU. See
page 12.2.
• The toner supply is low. You may be able to
temporarily extend the toner cartridge life. See
quality, install a new toner cartridge.
• The paper may not meet paper specifications;
for example, the paper is too moist or too
Gray background
If the amount of background shading becomes
unacceptable:
• Change to a lighter weight paper. See
• If the entire page is light, the print resolution
setting is too low or the toner save mode is on.
Adjust the print resolution and turn the toner
save mode off. See the help screen of the
• A combination of faded or smeared defects
may indicate that the toner cartridge needs
• Check the machine’s environment: very dry
(low humidity) or high humidity (higher than
80% RH) conditions can increase the amount
of background shading.
• Remove the old toner cartridge and install a
new one. See page 12.4.
Toner smear
• Clean the inside of the machine. See
page 12.2.
• Check the paper type and quality. See
• The surface of the LSU part inside the
machine may be dirty. Clean the LSU. See
page 12.2.
• Remove the toner cartridge and install a new
one. See page 12.4.
Toner specks
• The paper may not meet specifications; for
example, the paper is too moist or too rough.
• The transfer roller may be dirty. Clean the
inside of your machine. See page 12.2.
• The paper path may need cleaning. See page
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Vertical repetitive
defects
If marks repeatedly appear on the printed side of
the page at even intervals:
• The toner cartridge may be damaged. If a
repetitive mark occurs on the page, print a
cleaning sheet several times to clean the
you still have the same problems, remove the
toner cartridge and install a new one. See
page 12.4.
• Parts of the machine may have toner on them.
If the defects occur on the back of the page,
the problem will likely correct itself after a few
more pages.
Dropouts
If faded areas, generally rounded, occur
randomly on the page:
• A single sheet of paper may be defective. Try
reprinting the job.
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
• The moisture content of the paper is uneven
or the paper has moist spots on its surface.
Try a different brand of paper. See page 5.7.
• The paper lot is bad. The manufacturing
processes can cause some areas to reject
toner. Try a different kind or brand of paper.
• If these steps do not correct the problem,
contact a service representative.
• The fusing assembly may be damaged.
Contact a service representative.
13.8
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Condition
Suggested solutions
Condition
Suggested solutions
Background scatter Background scatter results from bits of toner
Wrinkles or creases • Ensure that the paper is loaded properly.
• Check the paper type and quality. See
randomly distributed on the printed page.
• The paper may be too damp. Try printing with
a different batch of papers. Do not open
packages of paper until necessary so that the
paper does not absorb too much moisture.
• Turn over the stack of paper in the tray. Also
try rotating the paper 180° in the tray.
• If background scatter occurs on an envelope,
A
change the printing layout to avoid printing
over areas that have overlapping seams on
the reverse side. Printing on seams can cause
problems.
• If background scatter covers the entire surface
area of a printed page, adjust the print
resolution through your software application or
the printer properties.
Back of printouts
are dirty
Check for leaking toner. Clean the inside of the
machine. See page 12.2.
Misformed
characters
• If characters are improperly formed and
producing hollow images, the paper stock may
be too slick. Try a different paper. See page
5.7.
• If characters are improperly formed and
producing a wavy effect, the scanner unit may
need service. For service, contact a service
representative.
Black pages
• The toner cartridge may not be installed
properly. Remove the cartridge and reinsert it.
• The toner cartridge may be defective and
need replacing. Remove the toner cartridge
and install a new one. See page 12.4.
• The machine may require to be repaired.
Contact a service representative.
Page skew
• Ensure that the paper is loaded properly.
• Check the paper type and quality. See
page 5.7.
• Ensure that the paper or other material is
loaded correctly and the guides are not too
tight or too loose against the paper stack.
Loose toner
• Clean the inside of the machine. See
page 12.2.
• Check the paper type and quality. See
• Remove the toner cartridge and install a new
one. See page 12.4.
• If the problem persists, the machine may
require repair. Contact a service
representative.
Curl or wave
• Ensure that the paper is loaded properly.
• Check the paper type and quality. Both high
temperature and humidity can cause the
paper to curl. See page 5.7.
• Turn over the stack of paper in the tray. Also
try rotating the paper 180° in the tray.
Character Voids
Character voids are white areas within parts of
characters that should be solid black:
• If you are using transparencies, try another
type of transparency. Because of the
composition of transparencies, some
character voids are normal.
• You may be printing on the wrong surface of
the paper. Remove the paper and turn it
around.
• The paper may not meet paper specifications.
A
13.9
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying problems
Condition
Suggested solutions
Horizontal stripes
If horizontally aligned black streaks or smears
appear:
Condition
Suggested solutions
Copies are too light Use Darkness to darken or lighten the
or too dark.
• The toner cartridge may be installed
improperly. Remove the cartridge and reinsert
it.
• The toner cartridge may be defective. Remove
the toner cartridge and install a new one. See
page 12.4.
• If the problem persists, the machine may
require repair. Contact a service
representative.
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
background of the copies.
Smears, lines,
marks, or spots
appears on copies.
• If defects are on the original, press Darkness
to lighten the background of your copies.
• If no defects are on the original, clean the scan
unit. See page 12.3.
Copy image is
skewed.
• Ensure that the original is face down on the
scanner glass or face up in the ADF.
• Check that the copy paper is loaded correctly.
Curl
If the printed paper is curled or paper does not
feed into the machine:
Blank copies print
out.
Ensure that the original is face down on the
scanner glass or face up in the ADF.
• Turn over the stack of paper in the tray. Also
try rotating the paper 180° in the tray.
Image rubs off the
copy easily.
• Replace the paper in the tray with paper from a
new package.
• In high humidity areas, do not leave paper in
the machine for extended periods of time.
Your printer is probably being used at an altitude
of 2,500 m (8,200 ft) or above.
An unknown image
repetitively appears
on a next few
sheets or loose
toner, light print, or
contamination
occurs.
Frequent copy
paper jams occur.
• Fan the stack of paper, then turn it over in the
tray. Replace the paper in the tray with a fresh
supply. Check/adjust the paper guides, if
necessary.
• Ensure that the paper is the proper paper
weight. 75 g/m2 bond paper is recommended.
• Check for copy paper or pieces of copy paper
remaining in the machine after a paper jam has
been cleared.
The high altitude may affect the print quality
such as loose toner or light imaging. You can set
this option through the Printer tab in printer
driver's properties. Refer to the Software
Section for details.
Toner cartridge
produces fewer
copies than
expected before
running out of
toner.
• Your originals may contain pictures, solids, or
heavy lines. For example, your originals may
be forms, newsletters, books, or other
documents that use more toner.
• The machine may be turned on and off
frequently.
• The scanner lid may be left open while copies
are being made.
13.10
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanning problems
Fax problems
Condition
Suggested solutions
Condition
Suggested solutions
The scanner does
not work.
• Make sure that you place the original to be
scanned face down on the scanner glass, or
face up in the ADF.
• There may not be enough available memory
to hold the document you want to scan. Try
the Prescan function to see if that works. Try
lowering the scan resolution rate.
The machine is not • Unplug the power cord and plug it in again.
working, there is no
display and the
buttons are not
working.
• Ensure that there is power to the electrical
outlet.
No dial tone
sounds.
• Check that the phone line is connected
properly.
• Check that the USB cable is connected
properly.
• Check that the phone socket in the wall is
working by plugging in another phone.
• Make sure that the USB cable is not
defective. Switch the cable with a known
good cable. If necessary, replace the cable.
• Check that the scanner is configured
correctly. Check scan setting in the SmarThru
Configuration or the application you want to
use to make certain that the scanner job is
being sent to the correct port.
The numbers
stored in memory
do not dial
Make sure that the numbers are stored in
memory correctly. Print a Phone Book list,
correctly.
The original does
not feed into the
machine.
• Make sure that the paper is not wrinkled and
you are putting it in correctly. Check that the
original is the right size, not too thick or thin.
• Make sure that the ADF is firmly closed.
• The ADF rubber pad may need to be replaced.
See page 12.6.
The unit scans very
slowly.
• Check if the machine is printing received
data. If so, scan the document after the
received data has been printed.
• Graphics are scanned more slowly than text.
• Communication speed slows in scan mode
because of the large amount of memory
required to analyze and reproduce the
scanned image. Set your computer to the
ECP printer mode through the BIOS setting.
It will help to increase the speed. For details
about how to set BIOS, refer to your
computer user’s guide.
Faxes are not
received
automatically.
• The receiving mode should be set to Fax.
• Make sure that there is paper in the tray.
• Check to see if the display shows any error
messages. If it does, clear the problem.
The machine does • Make sure that the original is loaded in the ADF
not send.
or on the scanner glass.
• Sending should show up on the display.
• Check the fax machine you are sending to, to
see if it can receive your fax.
The incoming fax
has blank spaces
or is of poor-
quality.
• The fax machine sending you the fax may be
faulty.
• A noisy phone line can cause line errors.
• Check your machine by making a copy.
• The toner cartridge may be empty. Replace the
Some of the words The fax machine sending you the fax had a
on an incoming fax temporary document jam.
are stretched.
There are lines on
the originals you
send.
Check your scan unit for marks and clean it. See
The machine dials
a number, but a
The other fax machine may be turned off, out of
paper, or cannot answer incoming calls. Speak
connection with the with the other machine operator and ask her/him
other fax machine
fails.
to sort out the problem.
13.11
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Common PostScript problems (SCX-4725FN only)
Condition
Suggested solutions
The following situations are PS language specific and may occur when
several printer languages are being used.
Faxes do not store
in memory.
There may not be enough memory space to store
the fax. If the display shows the Memory Full
message, delete from memory any faxes you no
longer need and then try again to store the fax.
Note
To receive a printed or screen-displayed message when PostScript
errors occur, open the Print Options window and click the desired
selection next to the PostScript errors section.
Blank areas
You may have chosen the wrong paper settings
in the user option setting. For details about paper
settings, see page 5.7.
appear at the
bottom of each
page or on other
pages, with a small
strip of text at the
top.
Problem
Possible cause
Suggested solutions
PostScript file
cannot be
printed.
The PostScript
driver may not be
installed correctly.
• Install the PostScript driver,
referring to the Software
Section
.
• Print a configuration page
and verify that the PS version
is available for printing.
• If the problem persists,
contact a service
Common Windows problems
Condition
Suggested solutions
representative.
“File in Use”
message appears
during installation.
Exit all software applications. Remove all
software from the StartUp Group, then restart
Windows. Reinstall the printer driver.
“Limit Check
Error”message too complex.
appears.
The print job was
You might need to reduce the
complexity of the page or install
more memory.
“Error Writing to
LPTx” message
appears.
• Ensure that the cables are connected correctly,
and that the machine is switched on.
• If bi-directional communication is not turned on
in the driver, it will also cause this message.
A PostScript
error page
prints.
The print job may
not be PostScript.
Make sure that the print job is a
PostScript job. Check to see
whether the software
application expected a setup or
PostScript header file to be
sent to the machine.
“General
Close all other applications, reboot Windows and
try printing again.
Protection Fault”,
“Exception OE”,
“Spool32”, or
“Illegal Operation”
messages appear.
When print a
document in
Macintosh with
Acrobat
Reader 6.0 or
higher, colors
print
The resolution
setting in the
printer driver may
not be matched
with that in
Make sure that the resolution
setting in your printer driver
matches that in Acrobat
Reader.
“Fail To Print”, “A
printer timeout
error occurred.”
messages appear.
These messages may appear during printing.
Just keep waiting until the machine finishes
printing. If the message appears in standby mode
or after printing has been completed, check the
connection and/or whether an error has occurred.
Acrobat Reader.
incorrectly.
Note
Refer to Microsoft Windows 98/Me/2000/XP(32/64bit)/2003
(32/64bit) User’s Guide that came with your PC for further
information on Windows error messages.
13.12
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Linux problems
Problem
Possible cause and solutions
Problem
Possible cause and solutions
The machine does not
appear on the
scanners list.
• Check if your machine is attached to your
computer. Make sure that it is connected
properly via the USB port and is turned on.
• Check if the scanner driver for your
machine is installed in your system. Open
Unified Driver configurator, switch to
Scanners configuration, then press
Drivers. Make sure that driver with a name
corresponding to your machine's name is
listed in the window. Check if the port is not
busy. Since functional components of MFP
(printer and scanner) share the same I/O
interface (port), the situation of
The machine does not
print.
• Check if the printer driver is installed in your
system. Open Unified Driver configurator
and switch to the Printers tab in Printers
configuration window to look at the list of
available printers. Make sure that your
machine is displayed on the list. If not,
please, invoke Add new printer wizard to
set up your device.
• Check if the printer has started. Open
Printers configuration and select your
machine on the printers list. Look at the
description in the Selected printer pane. If
its status contains “(stopped)” string,
please, press the Start button. After that
normal operation of the printer should be
restored. The “stopped” status might be
activated when some problems in printing
occurred. For instance, this could be an
attempt to print a document when a port is
claimed by a scanning application.
simultaneous access of different
“consumer” application to the same port is
possible. To avoid possible conflicts, only
one of them at a time is allowed to gain
control over the device. The other
“consumer” will encounter “device busy”
response. This can usually happen while
starting scan procedure, and appropriate
message box appears.
• Check if the port is not busy. Since
functional components of MFP (printer and
scanner) share the same I/O interface
(port), the situation of simultaneous access
of different “consumer” applications to the
same port are possible. To avoid possible
conflicts, only one of them at a time is
allowed to gain control over the device. The
other “consumer” will encounter “device
busy” response. You should open ports
configuration and select the port assigned
to your printer. In the Selected port pane
you can see if the port is occupied by some
other application. If this is the case, you
should wait for completion of the current job
or should press Release port button, if you
are sure that the present owner is not
functioning properly.
• To identify the source of the problem, you
should open ports configuration and select
the port assigned to your scanner. port's
symbol /dev/mfp0 corresponds to LP:0
designation displayed in the scanners’
options, /dev/mfp1 relates to LP:1 and so
on. USB ports start at /dev/mfp4, so
scanner on USB:0 relates to /dev/mfp4
respectively and so forth sequentially. In the
Selected port pane you can see if the port
is occupied by some other application. If
this is the case, you should wait for
completion of the current job or you should
press Release port button, if you are sure
that the present port's owner is not
functioning properly.
The printer does not
print PDF file correctly.
Some parts of graphics,
text or illustrations are
missing.
Incompatibility between the PDF file and the
Acrobat products:
• Check if your application has special print
option such as “-oraw”. If “-oraw” is
Printing the PDF file as an image may solve this
problem. Turn on Print as Image from the
Acrobat printing options.
specified in the command line parameter
then remove it to print properly. For Gimp
front-end, select “print” -> “Setup printer”
and edit command line parameter in the
command item.
Note: It will take longer to print when you print a
PDF file as an image.
• The CUPS (Common Unix Printing System)
version distributed with SuSE Linux 9.2
(cups-1.1.21) has a problem with ipp
(Internet Printing Protocol) printing. Use the
socket printing instead of ipp or install later
version of CUPS (cups-1.1.22 or higher).
13.13
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible cause and solutions
Problem
Possible cause and solutions
The machine does not
scan.
• Check if a document is loaded into the
machine.
• Check if your machine is connected to the
computer. Make sure if it is connected
properly if an I/O error is reported while
scanning.
I encounter error
“Cannot open port
device file” when
printing a document.
Please avoid changing the print job
parameters (via LPR GUI, for example) while
a print job is in progress. Known versions of
CUPS server break the print job whenever
print options are changed and then try to
restart the job from the beginning. Since
Unified Linux Driver locks port while printing,
the abrupt termination of the driver keeps the
port locked and therefore unavailable for
subsequent print jobs. If this situation
• Check if the port is not busy. Since
functional components of MFP (printer and
scanner) share the same I/O interface
(port), the situation of simultaneous access
of different “consumer” application to the
same port is possible. To avoid possible
conflicts, only one of them at a time is
allowed to gain control over the device. The
other “consumer” will encounter “device
busy” response. This can usually happen
while starting scan procedure, and
appropriate message box will be displayed.
To identify the source of the problem, you
should open ports configuration and select
the port assigned to your scanner. port’s
symbol /dev/mfp0 corresponds to LP:0
designation displayed in the scanners’
options, /dev/mfp1 relates to LP:1 and so
on. USB ports start at /dev/mfp4, so
scanner on USB:0 relates to /dev/mfp4
respectively and so forth sequentially. In the
Selected port pane you can see if the port
is occupied by some other application. If
this is the case, you should wait for
completion of the current job or should
press the Release port button, if you are
sure that the present port’s owner is not
functioning properly.
occurred, please, try to release the port.
Common Macintosh problems (SCX-4725FN only)
Problem
Suggested solutions
The printer does not print Incompatibility between the PDF file and
PDF file correctly. Some
parts of graphics, text or
illustrations are missing.
the Acrobat products:
Printing the PDF file as an image may
solve this problem. Turn on Print as
Image from the Acrobat printing options.
Note: It will take longer to print when
you print a PDF file as an image.
The document has
printed, but the print job
has not disappeared from
the spooler in
Update your Mac OS to OS 10.3.3. or
higher.
Mac OS 10.3.2.
Some letters are not
displayed normally
during the Cover page
printing.
This problem is caused because Mac
OS can not create the font during the
Cover page printing. English alphabet
and numbers are displayed normally at
the Cover page.
I cannot scan via Gimp • Check if Gimp Front-end has
Front-end.
“Xsane: Device dialog.” on the “Acquire”
menu. If not, you should install Xsane plug-
in for Gimp on the your computer. You can
find Xsane plug-in package for Gimp on
Linux distribution CD or Gimp home page.
For the detail information, refer to the Help
for Linux distribution CD or Gimp Front-end
application.
If you wish to use other kind of scan
application, refer to the Help for application.
13.14
<
Troubleshooting>
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
14 Specifications
Weight (including
consumables)
11.2 Kg
This chapter includes:
•
•
•
•
Package weight
Duty cycle
Paper: 1.3 Kg, Plastic: 0.5 Kg
Monthly print: Up to 10,000 pages
1. Sound Pressure Level, ISO 7779
2. Average cartridge yield declared in accordance with ISO/IEC 19752.
The number of pages may be affected by operating environment, printing
interval, media type, and media size.
General specifications
Item
Description
Printer specifications
ADF
ADF document size
Up to 30 sheets (75 g/m2)
Item
Description
Laser Beam Printing
Width: 142 to 216 mm
Length: 148 to 356 mm
Printing method
1
Printing speed
Up to 24 ppm in A4 (24 ppm in Letter)
10 seconds (from ready)
Paper input capacity Tray: 250 multi-pages for plain paper
(75 g/m2)
First print out time
Print resolution
Printer language
Manual tray: 1 sheet of paper
(60 to 165 g/m2)
Up to 1,200 x 1,200 dpi effective output
Paper output
capacity
Output tray: 100 sheets (face down)
PCL 6, PS 3 (SCX-4725FN only),
SPL (for Linux only)
2
Consumables
Power rating
1-piece toner cartridge system
OS Compatibility
Windows 98/Me/2000/XP(32/64bit)/
2003(32/64bit)
110 - 127 VAC, 50/60 Hz, 5.5 A
220 - 240 VAC, 50/60 Hz, 3 A
Various Linux OS
Macintosh 10.3 ~ 10.4 (SCX-4725FN only)
Power consumption
Average: Less than 400 W
Interface
High Speed USB 2.0
Power save mode: Less than 13.5 W
Ethernet 10/100 Base TX (SCX-4725FN only)
1
Noise level
Standby mode: Less than 35 dBA
Printing: Less than 53 dBA
1. Print speed will be affected by operating system used, computing performance,
application software, connecting method, media type, media size, and job
complexity.
Copying mode: Less than 55 dBA
Warm up: Less than 49 dBA
Warm-up time
Less than 30 seconds (from sleep mode)
Operating
environment
Temperature: 10 °C to 32 °C
Humidity: 20% to 80% RH
Display
16 characters x 2 lines
1,500 or 3,000 pages.
32 MB
2
Toner cartridge yield
Memory
External dimension
(W x D x H)
17.2 X 14.7 X 15.2 inches (438 x 374 x 387 mm)
14.1
<
Specifications>
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanner and copier specifications
Facsimile specifications
Item
Description
Item
Compatibility
Applicable line
Description
Compatibility
TWAIN standard/WIA standard
ITU-T Group 3
Scanning method
ADF and Flat-bed Color CIS (Contact Image
Sensor) module
Public Switched Telephone Network (PSTN)
or behind PABX
Resolution
Optical: 600 x 600 dpi (mono and color)
Enhanced: 4,800 x 4,800 dpi
Data coding
MH/MR/MMR/JBIG/JPEG/ECM (Error
Correction Mode)
Modem speed
33.6 Kbps
Effective scanning
length
Scanner glass: 297 mm
ADF: 356 mm
1
Transmission
speed
Approx. 3 seconds/page
Effective scanning
width
Max 208 mm
Maximum
Scanner glass: 297 mm
document length
Automatic document glass: 356 mm
Color bit depth
Mono bit depth
24 bit
Resolution
Standard: 203 x 98 dpi
Fine: 203 x 196 dpi
1 bit for Black & White mode
8 bit for Gray mode
Super Fine: 300 x 300 dpi
Photo: 203 x 196 dpi
Color: 200 x 200 dpi
1
Copy speed
Up to 24 ppm in A4 (24 ppm in Letter)
Copy resolution
Scan: up to 600 x 300 (text, text/photo)
up to 600 x 600 (photo using platen)
up to 600 x 300 (photo using ADF)
Memory
4 MB
Print: up to 600 x 600 (text, text/photo, photo)
Halftone
Auto dialer
256 levels
Zoom rate
Scanner glass: 25 to 400%
ADF: 25 to 100%
Group dialing (up to 200 numbers)
1. Transmission time applies to memory transmission of text data with ECM
compression using only ITU-T No.1 Chart.
Multiple copies
Grayscale
1 to 99 pages
256 levels
1. Copy Speed is based on Single Document Multiple Copy.
14.2
<
Specifications>
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Numerics
D
J
jam, clear
document 13.1
paper 13.1
DRPD (Distinctive Ring Pattern Detection)
drum, clean
A
ADF 1.2
K
automatically 12.5
manually 12.5
L
E
loading originals
ADF 5.1
B
loading paper
tray 5.5
F
faxing
C
cleaning
M
drum 12.5
inside 12.2
LSU 12.3
outside 12.2
copying
N
network configuration
print 4.2
G
restore 4.2
network setup
2/4-up 6.3
clone 6.2
H
EtherTalk 4.2
TCP/IP 4.1
,
poster 6.4
n-up (multiple pages per sheet)
copying 6.3
I
1
Download from Www.Somanuals.com. All Manuals Search And Download.
O
V
originals
volume, adjust
ringer 2.3
redialing
automatically 9.3
manually 9.3
replacing
ringer 2.3
loading 5.1
speaker 2.3
W
P
paper jam, clear
fuser area or around toner cartridge
tray 13.2
S
scanner glass
paper load
tray 5.5
paper size
setting 5.7
specifications 5.3
paper type
setting 5.7
specifications 5.3
Phone Book
printing
cleaning 12.3
sending a fax
automatically 9.2
manually 9.2
specifications
facsimile 14.2
general 14.1
paper 5.3
printer 14.1
reports 12.1
system requirements
Linux 3.3
problem, solve
copying 13.10
faxing 13.11
Macintosh 3.3
Windows 3.2
Linux 13.13
Macintosh 13.14
printing 13.6
T
scanning 13.11
Windows 13.12
toner cartridge
cleaning 12.5
maintaining 12.3
redistributing 12.4
replacing 12.4
R
receiving a fax
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Samsung Printer
Software section
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE SECTION
CONTENTS
Installing Printer Software ........................................................................................................ 4
Installing Software for Local Printing ................................................................................. 4
Installing Software for Network Printing ............................................................................. 7
Reinstalling Printer Software ................................................................................................... 10
Removing Printer Software ..................................................................................................... 11
Printing a Document .............................................................................................................. 12
Printing to a file (PRN) .......................................................................................................... 12
Printer Settings ..................................................................................................................... 13
Layout Tab .................................................................................................................. 13
Paper Tab .................................................................................................................... 14
Graphics Tab ............................................................................................................... 15
Extras Tab ................................................................................................................... 16
About Tab ................................................................................................................... 16
Printer Tab .................................................................................................................. 16
Using a Favorite Setting ................................................................................................ 17
Using Help ................................................................................................................... 17
Printing Multiple Pages on One Sheet of Paper (N-Up Printing) ..................................................... 18
Printing Posters ..................................................................................................................... 19
Printing a Reduced or Enlarged Document ................................................................................ 19
Fitting Your Document to a Selected Paper Size ......................................................................... 19
Using Watermarks ................................................................................................................. 20
Using an Existing Watermark ......................................................................................... 20
Creating a Watermark ................................................................................................... 20
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing a Watermark ..................................................................................................... 20
Deleting a Watermark ................................................................................................... 20
Using Overlays ...................................................................................................................... 21
What is an Overlay? ...................................................................................................... 21
Creating a New Page Overlay ......................................................................................... 21
Using a Page Overlay .................................................................................................... 21
Deleting a Page Overlay ................................................................................................ 21
(SCX-4725FN ONLY)
Printer Settings ..................................................................................................................... 22
Advanced .................................................................................................................. 22
Using Help ................................................................................................................... 22
Setting Up a Host Computer ................................................................................................... 23
Setting Up a Client Computer .................................................................................................. 23
Understanding Smart Panel .................................................................................................... 24
Opening the Troubleshooting Guide ......................................................................................... 24
Using Printer Settings Utility ................................................................................................... 25
Using Onscreen Help File ............................................................................................... 25
Changing the Smart Panel Program Settings ............................................................................. 25
Scanning Using Samsung SmarThru ......................................................................................... 26
Uninstalling Samsung SmarThru ..................................................................................... 26
Using Samsung SmarThru ............................................................................................. 27
Using Onscreen Help File ............................................................................................... 28
Scanning Process with TWAIN-enabled Software ........................................................................ 28
Scanning Using the WIA Driver ................................................................................................ 28
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started ..................................................................................................................... 29
Installing the Unified Linux Driver ............................................................................................ 29
Installing the Unified Linux Driver ................................................................................... 29
Uninstalling the Unified Linux Driver ............................................................................... 30
Using the Unified Driver Configurator ....................................................................................... 31
Opening the Unified Driver Configurator .......................................................................... 31
Printers Configuration ................................................................................................... 31
Scanners Configuration ................................................................................................. 32
Ports Configuration ....................................................................................................... 32
Configuring Printer Properties ................................................................................................. 33
Printing a Document .............................................................................................................. 33
Printing from Applications .............................................................................................. 33
Printing Files ................................................................................................................ 34
Scanning a Document ............................................................................................................ 34
Using the Image Manager .............................................................................................. 35
(SCX-4725FN ONLY)
Installing Software for Macintosh ............................................................................................. 37
Setting Up the Printer ............................................................................................................ 38
For a Network-connected Macintosh ................................................................................ 38
For a USB-connected Macintosh ..................................................................................... 38
Printing ................................................................................................................................ 39
Printing a Document ..................................................................................................... 39
Changing Printer Settings .............................................................................................. 39
Printing Multiple Pages on One Sheet of Paper .................................................................. 40
Scanning .............................................................................................................................. 41
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Installation
1
Installing Printer
Software in Windows
This is recommended for most users. All components necessary
for printer operations will be installed.
1
2
Make sure that the printer is connected to your computer
and powered on.
This chapter includes:
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK
.
Installing Printer Software
You can install the printer software for local printing or network
printing. To install the printer software on the computer,
perform the appropriate installation procedure depending on
the printer in use.
A printer driver is software that lets your computer
communicate with your printer. The procedure to install drivers
may differ depending on the operating system you are using.
All applications should be closed on your PC before beginning
installation.
Installing Software for Local Printing
3
4
Click Next
.
• If necessary, select a language from the drop-down list.
A local printer is a printer directly attached to your computer
using the printer cable supplied with your printer, such as a USB
or parallel cable. If your printer is attached to a network, skip
this step and go to “Installing Software for Network Printing” on
•
View User’s Guide: Allows you to view the User’s
Guide. If your computer doesn’t have Adobe Acrobat,
click on this option and it will automatically install Adobe
Acrobat Reader for you.
You can install the printer software using the typical or custom
method.
Select Typical installation for a local printer. Click
Next
.
NOTE: If the “New Hardware Wizard” window appears during
the installation procedure, click
in the upper right corner of
the box to close the window, or click Cancel
.
4
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
7
To register yourself as a user of Samsung Printers in order
to receive information from Samsung, select the checkbox
and click Finish. You are now sent to the Samsung web
site.
NOTE: If your printer is not already connected to the
computer, the following window will appear.
Otherwise, just click Finish
.
• After connecting the printer, click Next
.
• If you don’t want to connect the printer at this time, click
Next, and No on the following screen. Then the installation
will start and a test page will not be printed at the end of the
installation.
• The installation window that appears in this User’s
Guide may differ depending on the printer and
interface in use.
NOTE: After setup is complete, if your printer driver doesn’t
Custom Installation
5
6
After the installation is finished, a window asking you to
print a test page appears. If you choose to print a test
You can choose individual components to install.
page, select the checkbox and click Next
.
1
2
Make sure that the printer is connected to your computer
and powered on.
Insert the supplied CD-ROM into your CD-ROM drive.
If the test page prints out correctly, click Yes
.
The CD-ROM should automatically run, and an installation
window appears.
If not, click No to reprint it.
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK
.
5
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
Click Next
.
• If necessary, select a language from the drop-down list.
NOTE: If your printer is not already connected to the
computer, the following window will appear.
•
View User’s Guide: Allows you to view the User’s
Guide. If your computer doesn’t have Adobe Acrobat,
click on this option and it will automatically install Adobe
Acrobat Reader for you.
Select Custom installation. Click Next
.
• After connecting the printer, click Next
.
• If you don’t want to connect the printer at this time, click
Next, and No on the following screen. Then the installation
will start and a test page will not be printed at the end of the
installation.
• The installation window that appears in this User’s
Guide may differ depending on the printer and
interface in use.
5
Select your printer and click Next.
6
Select the components to be installed and click Next.
NOTE: You can change the desired installation folder by
clicking [Browse].
6
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
7
After the installation is finished, a window asking you to
print a test page appears. If you choose to print a test
If the installation window does not appear, click Start and
then Run. Type X:\Setup.exe, replacing “ ” with the
letter which represents your drive and click OK
X
page, select the checkbox and click Next
.
.
8
9
If the test page prints out correctly, click Yes.
If not, click No to reprint it.
To register yourself as a user of Samsung Printers in order
to receive information from Samsung, select the checkbox
and click Finish. You are now sent to the Samsung web
site.
Otherwise, just click Finish
.
3
4
Click Next
.
• If necessary, select a language from the drop-down list.
•
View User’s Guide: Allows you to view the User’s
Guide. If your computer doesn’t have Adobe Acrobat,
click on this option and it will automatically install Adobe
Acrobat Reader for you.
Select Typical installation for a network printer. Click
Next
.
Installing Software for Network
Printing
When you connect your printer to a network, you must first
configure the TCP/IP settings for the printer. After you have
assigned and verified the TCP/IP settings, you are ready to
install the software on each computer on the network.
You can install the printer software using the typical or custom
method.
Typical Installation
This is recommended for most users. All components necessary
for printer operations will be installed.
1
Make sure that the printer is connected to your network
and powered on. For details about connecting to the
network, see the supplied printer’s User’s Guide.
2
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
7
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
5
The list of printers available on the network appears.
Select the printer you want to install from the list and then
NOTE: After setup is complete, if your printer driver doesn’t
click Next
.
Custom Installation
You can choose individual components to install and set a
specific IP address.
1
Make sure that the printer is connected to your network
and powered on. For details about connecting to the
network, see the supplied printer’s User’s Guide.
2
Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automatically run, and an installation
window appears.
If the installation window does not appear, click Start and
• If you do not see your printer on the list, click Update to
refresh the list, or select Add TCP/IP Port to add your
printer to the network. To add the printer to the
network, enter the port name and the IP address for the
printer.
then Run. Type X:\Setup.exe, replacing “X” with the
letter which represents your drive and click OK
.
To verify your printer’s IP address or the MAC address,
print a Network Configuration page.
• To find a shared network printer (UNC Path), select
Shared Printer [UNC] and enter the shared name
manually or find a shared printer by clicking the Browse
button.
NOTE: To search the network printer, the firewall disabled.
6
After the installation is finished, a window appears asking
you to print a test page and to register yourself as a user
of Samsung Printers in order to receive information from
Samsung. If you so desire, select the corresponding
3
Click Next
.
• If necessary, select a language from the drop-down list.
checkbox(es) and click Finish
.
•
View User’s Guide: Allows you to view the User’s
Guide. If your computer doesn’t have Adobe Acrobat,
click on this option and it will automatically install Adobe
Acrobat Reader for you.
Otherwise, just click Finish
.
8
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Select Custom installation. Click Next.
TIP: If you want to set a specific IP address on a specific
network printer, click the Set IP Address button. The Set IP
Address window appears. Do as follows:
5
The list of printers available on the network appears.
Select the printer you want to install from the list and then
click Next
.
a. Select a printer to be set with a specific IP address from the
list.
b. Configure an IP address, subnet mask, and gateway for the
printer manually and click Configure to set the specific IP
address for the network printer.
c. Click Next
.
6
Select the components to be installed. After selecting the
components, the following window appears. You can also
change the printer name, set the printer to be shared on
the network, set the printer as the default printer, and
change the port name of each printer. Click Next
.
• If you do not see your printer on the list, click Update to
refresh the list, or select Add TCP/IP Port to add your
printer to the network. To add the printer to the
network, enter the port name and the IP address for the
printer.
To verify your printer’s IP address or the MAC address,
print a Network Configuration page.
• To find a shared network printer (UNC Path), select
Shared Printer [UNC] and enter the shared name
manually or find a shared printer by clicking the Browse
button.
To install this software on a server, select the Setting up
this printer on a server checkbox.
NOTE: To search the network printer, the firewall disabled.
9
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
7
After the installation is finished, a window appears asking
you to print a test page and to register yourself as a user
of Samsung Printers in order to receive information from
Samsung. If you so desire, select the corresponding
Reinstalling Printer Software
You can reinstall the software if installation fails.
checkbox(es) and click Finish
.
1
2
Start Windows.
Otherwise, just click Finish
.
From the Start menu select Programs or All Programs
→
your printer driver name
→
Maintenance.
3
4
Select Repair and click Next
.
The list of printers available on the network appears.
Select the printer you want to install from the list and then
click Next
.
NOTE: After setup is complete, if your printer driver doesn’t
• If you do not see your printer on the list, click Update to
refresh the list, or select Add TCP/IP Port to add your
printer to the network. To add the printer to the
network, enter the port name and the IP address for the
printer.
• To find a shared network printer (UNC Path), select
Shared Printer [UNC] and enter the shared name
manually or find a shared printer by clicking the Browse
button.
You will see a component list so that you can reinstall any
item individually.
10
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If your printer is not already connected to the
computer, the following window will appear.
Removing Printer Software
1
2
Start Windows.
From the Start menu select Programs or All Programs
→
your printer driver name
→
Maintenance.
3
Select Remove and click Next
.
You will see a component list so that you can remove any
item individually.
4
5
Select the components you want to remove and then click
Next
When your computer asks you to confirm your selection,
click Yes
.
.
The selected driver and all of its components are removed
from your computer.
6
After the software is removed, click Finish.
• After connecting the printer, click Next
.
• If you don’t want to connect the printer at this time, click
Next, and No on the following screen. Then the installation
will start and a test page will not be printed at the end of the
installation.
• The reinstallation window that appears in this User’s
Guide may differ depending on the printer and
interface in use.
5
Select the components you want to reinstall and click
Next
.
If you installed the printer software for local printing
and you select your printer driver name, the window
asking you to print a test page appears. Do as follows:
a. To print a test page, select the check box and click
Next
.
b. If the test page prints out correctly, click Yes
.
If it doesn’t, click No to reprint it.
6
When the reinstallation is done, click Finish
.
11
Installing Printer Software in Windows
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Open the document you want to print.
Select Print from the File menu. The Print window is
displayed. It may look slightly different depending on your
application.
2
Basic Printing
This chapter explains the printing options and common printing
tasks in Windows.
The basic print settings are selected within the Print
window. These settings include the number of copies and
print range.
This chapter includes:
Make sure that your
printer is selected.
3
4
Select your printer driver from the Name drop-down
list.
To take advantage of the printer features provided by your
printer driver, click Properties or Preferences in the
application’s Print window. For details, see “Printer
Printing a Document
NOTES
:
If you see Setup Printer, or Options in your Print
,
window, click it instead. Then click Properties on the next
screen.
• Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
However the composition of the printer properties window is
similar.
• Check the Operating System(s) that are compatible
with your printer. Please refer to the OS Compatibility
section of Printer Specifications in your Printer User’s
Guide.
Click OK to close the printer properties window.
To start the print job, click OK or Print in the Print
window.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
Printing to a file (PRN)
The following procedure describes the general steps required
for printing from various Windows applications. The exact steps
for printing a document may vary depending on the application
program you are using. Refer to the User’s Guide of your
software application for the exact printing procedure.
You will sometimes need to save the print data as a file for your
purpose.
To create a file:
1
2
Check the Print to file box at the Print window.
Select the folder and assign a name of the file and then
click OK.
12
Basic Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Layout Tab
The Layout tab provides options to adjust how the document
appears on the printed page. The Layout Options includes
a Document” on page 12 for more information on accessing
printer properties.
Printer Settings
You can use the printer properties window, which allows you to
access all of the printer options you need when using your
printer. When the printer properties are displayed, you can
review and change the settings needed for your print job.
Your printer properties window may differ, depending on your
operating system. This Software User’s Guide shows the
Properties window for Windows XP.
1
2
Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
If you access printer properties through the Printers folder, you
can view additional Windows-based tabs (refer to your
page 16).
NOTES
:
• Most Windows applications will override settings you specify
in the printer driver. Change all print settings available in the
software application first, and change any remaining settings
using the printer driver.
• The settings you change remain in effect only while you are
using the current program. To make your changes
permanent, make them in the Printers folder.
• The following procedure is for Windows XP. For other
Windows OS, refer to the corresponding Windows User's
Guide or online help.
Paper Orientation
Paper Orientation allows you to select the direction in which
information is printed on a page.
1. Click the Windows Start button.
•
•
Portrait prints across the width of the page, letter style.
Landscape prints across the length of the page, spreadsheet
style.
2. Select Printers and Faxes
.
3. Select your printer driver icon.
4. Right-click on the printer driver icon and select
•
Rotate allows you to rotate the page the selected degrees.
Printing Preferences
.
5. Change the settings on each tab, click OK.
Landscape
Portrait
Layout Options
Layout Options allows you to select advanced printing options.
You can choose Multiple Pages per Side and Poster Printing
.
•
For details, see “Printing Multiple Pages on One Sheet of Paper
•
For details, see “Printing Posters” on page 19.
13
Basic Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper Tab
3
Source
Make sure that Source is set to the corresponding paper tray.
Use Manual Feeder when printing on special materials like
envelopes and transparencies. You have to load one sheet at a
time into the Manual Tray or Multi-Purpose Tray.
If the paper source is set to Auto Selection, the printer
automatically picks up print material in the following tray order:
Manual Tray or Multi-Purpose Tray, Tray n.
Use the following options to set the basic paper handling
specifications when you access the printer properties. See
“Printing a Document” on page 12 for more information on
accessing printer properties.
Click the Paper tab to access various paper properties.
1
2
4
Type
Set Type to correspond to the paper loaded in the tray from
which you want to print. This will let you get the best quality
printout. If not, print quality may not be acheived as you want.
Cotton: 20 lb to 24 lb (75~90 g/m2) cotton paper such as Gilbert
25 % and Gilbert 100 %.
3
4
Plain Paper: Normal plain paper. Select this type if your printer is
monochrome and printing on the 16 lb (60 g/m2) cotton paper.
Recycled Paper: 20 lb to 24 lb (75~90 g/m2) recycled paper.
Color Paper: 20 lb to 24 lb (75~90 g/m2) color-backgrounded
paper.
5
5
Scaling Printing
Scaling Printing allows you to automatically or manually scale
your print job on a page. You can choose from None Reduce/
Enlarge, and Fit to Page
,
.
•
For details, see “Printing a Reduced or Enlarged Document” on
1
Copies
•
For details, see “Fitting Your Document to a Selected Paper
Copies allows you to choose the number of copies to be printed.
You can select 1 to 999 copies.
2
Size
Size allows you to set the size of paper you loaded in the tray.
If the required size is not listed in the Size box, click Custom
When the Custom Paper Setting window appears, set the paper
size and click OK. The setting appears in the list so that you can
select it.
.
14
Basic Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Options
Graphics Tab
Use the following Graphic options to adjust the print quality for
your specific printing needs. See “Printing a Document” on
page 12 for more information on accessing printer properties.
You can set advanced settings by clicking the Advanced
Options button.
•
TrueType Options: This option determines what the driver
tells the printer about how to image the text in your document.
Select the appropriate setting according to the status of your
document. This option may be available only in
Windows 9x/Me, depending on your particular printer
model.
Click the Graphic tab to display the properties shown below.
-
Download as Outline: When this option is selected, the
driver will download any TrueType fonts that are used in your
document not already stored (resident) on your printer. If,
after printing a document, you find that the fonts did not print
correctly, choose Download as bit image and resubmit your
print job. The Download as bit image setting is often useful
when printing Adobe. This feature is available only
when you use the PCL printer driver.
-
-
Download as Bitmap: When this option is selected, the
driver will download the font data as bitmap images.
Documents with complicated fonts, such as Korean or
Chinese, or various other fonts, will print faster in this setting.
Print as Graphics: When this option is selected, the driver
will download any fonts as graphics. When printing documents
with high graphic content and relatively few TrueType fonts,
printing performance (speed) may be enhanced in this
setting.
•
Print All Text To Black: When the Print All Text To
Black option is checked, all text in your document prints solid
black, regardless of the color it appears on the screen.
Resolution
The Resolution options you can select may vary
depending on your printer model. The higher the setting,
the sharper the clarity of printed characters and graphics. The
higher setting also may increase the time it takes to print a
document.
Image Mode
The available options are Normal and Text Enhance. Some
printers do not support this feature.
•
Printer Setting: If you select this option, this feature is
determined by the setting you’ve made on the control panel of
the printer.
•
•
Normal: This setting is for normal documents.
Text Enhance: Image Mode allows the user to enhance
printouts.
Toner Save Mode
Selecting this option extends the life of your toner cartridge and
reduces your cost per page without a significant reduction in print
quality. Some printers do not support this feature.
•
Printer Setting: If you select this option, this feature is
determined by the setting you’ve made on the control panel of
the printer.
•
•
On: Select this option to allow the printer to use less toner on
each page.
Off: If you don’t need to save toner when printing a document,
select this option.
15
Basic Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Extras Tab
About Tab
You can select output options for your document. See “Printing
a Document” on page 12 for more information about accessing
the printer properties.
Use the About tab to display the copyright notice and the
version number of the driver. If you have an Internet browser,
you can connect to the Internet by clicking on the web site icon.
See “Printing a Document” on page 12 for more information
about accessing printer properties.
Click the Extras tab to access the following feature:
1
2
3
Printer Tab
If you access printer properties through the Printers folder,
you can view the Printer tab. You can set the printer
configuration.
The following procedure is for Windows XP. For other Windows
OS, refer to the corresponding Windows User's Guide or online
help.
1
2
3
4
Click the Windows Start menu.
Select Printers and Faxes
.
Select your printer driver icon.
Right-click on the printer driver icon and select
Properties
.
5
Click the Printer tab and set the options.
1
Watermark
You can create a background text image to be printed on each
2
Overlay
Overlays are often used to take the place of preprinted forms and
3
Output Options
•
Print Subset: You can set the sequence in which the pages
print. Select the print order from the drop-down list.
-
-
-
-
Normal (1,2,3): Your printer prints all pages from the first
page to the last page.
Reverse All Pages (3,2,1): Your printer prints all pages
from the last page to the first page.
Print Odd Pages: Your printer prints only the odd numbered
pages of the document.
Print Even Pages: Your printer prints only the even
numbered pages of the document.
•
Use Printer Fonts: When Use Printer Fonts is checked, the
printer uses the fonts that are stored in its memory (resident
fonts) to print your document, rather than downloading the
fonts used in your document. Because downloading fonts takes
time, selecting this option can speed up your printing time.
When using Printer fonts, the printer will try to match the fonts
used in your document to those stored in its memory. If,
however, you use fonts in your document that are very different
from those resident in the printer, your printed output will
appear very different from what it looks like on the screen.
This feature is available only when you use the PCL
printer driver.
16
Basic Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Favorite Setting
The Favorites option, which is visible on each properties tab,
allows you to save the current properties settings for future
use.
To save a Favorites item:
1
2
Change the settings as needed on each tab.
Enter a name for the item in the Favorites input box.
3
Click Save.
When you save Favorites, all current driver settings are
saved.
To use a saved setting, select the item from the Favorites drop
down list. The printer is now set to print according to the
Favorites setting you selected.
To delete a Favorites item, select it from the list and click
Delete
.
You can also restore the printer driver’s default settings by
selecting Printer Default from the list.
Using Help
Your printer has a help screen that can be activated by clicking
the Help button in the printer properties window. These help
screens give detailed information about the printer features
provided by the printer driver.
You can also click
from the upper right corner of the window,
and then click on any setting.
17
Basic Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Advanced Printing
This chapter explains printing options and advanced printing
tasks.
Printing Multiple Pages on One
Sheet of Paper (N-Up Printing)
You can select the number of pages to print on a single sheet
of paper. To print more than one page per sheet, the pages will
be reduced in size and arranged in the order you specify. You
can print up to 16 pages on one sheet.
1
3
2
4
NOTE
:
• Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
However the composition of the printer properties window is
similar.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
1
To change the print settings from your software
application, access printer properties. See “Printing a
2
3
From the Layout tab, choose Multiple Pages per Side in
the Layout Type drop-down list.
Select the number of pages you want to print per sheet
(1, 2, 4, 6, 9, or 16) in the Pages per Side drop-down
list.
This chapter includes:
4
Select the page order from the Page Order drop-down
list, if necessary.
Check Print Page Border to print a border around each
page on the sheet.
Click the Paper tab, select the paper source, size, and
type.
5
6
Click OK and print the document.
18
Advanced Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Posters
Printing a Reduced or Enlarged
Document
This feature allows you to print a single-page document onto 4,
9, or 16 sheets of paper, for the purpose of pasting the sheets
together to form one poster-size document.
You can change the size of a page’s content to appear larger or
smaller on the printed page.
1
To change the print settings from your software
application, access printer properties. See “Printing a
1
To change the print settings from your software
application, access printer properties. See “Printing a
2
3
Click the Layout tab, select Poster Printing in the
Layout Type drop-down list.
Configure the poster option:
2
3
From the Paper tab, select Reduce/Enlarge in the
Printing Type drop-down list.
Enter the scaling rate in the Percentage input box.
You can select the page layout from Poster<2x2>
Poster<3x3>, or Poster<4x4>. If you select
,
You can also click the
or
button.
Poster<2x2>, the output will be automatically stretched
to cover 4 physical pages.
4
5
Select the paper source, size, and type in Paper Options.
Click OK and print the document.
Fitting Your Document to a
Selected Paper Size
Specify an overlap in millimeters or inches to make it
easier to pasting the sheets together.
This printer feature allows you to scale your print job to any
selected paper size regardless of the digital document size. This
can be useful when you want to check fine details on a small
document.
A
0.15 inches
1
To change the print settings from your software
application, access printer properties. See “Printing a
0.15 inches
2
3
From the Paper tab, select Fit to Page in the Printing
Type drop-down list.
Select the correct size from the Output size drop-down
list.
4
5
Click the Paper tab, select the paper source, size, and
type.
Click OK and print the document. You can complete the
poster by pasting the sheets together.
4
5
Select the paper source, size, and type in Paper Options.
Click OK and print the document.
19
Advanced Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing a Watermark
Using Watermarks
1
2
3
To change the print settings from your software
application, access printer properties. See “Printing a
Click the Extras tab and click the Edit button in the
Watermark section. The Edit Watermark window
appears.
Select the watermark you want to edit from the Current
Watermarks list and change the watermark message and
options.
The Watermark option allows you to print text over an existing
document. For example, you may want to have large gray
letters reading “DRAFT” or “CONFIDENTIAL” printed diagonally
across the first page or all pages of a document.
There are several predefined watermarks that come with the
printer, and they can be modified, or you can add new ones to
the list.
4
5
Click Update to save the changes.
Click OK until you exit the Print window.
Using an Existing Watermark
1
2
3
To change the print settings from your software
application, access printer properties. See “Printing a
Click the Extras tab, and select the desired watermark
from the Watermark drop-down list. You will see the
selected watermark in the preview image.
Deleting a Watermark
1
To change the print settings from your software
application, access printer properties. See “Printing a
2
From the Extras tab, click the Edit button in the
Watermark section. The Edit Watermark window
appears.
Click OK and start printing.
NOTE: The preview image shows how the page will look when
it is printed.
3
4
Select the watermark you want to delete from the Current
Watermarks list and click Delete
Click OK until you exit the Print window.
.
Creating a Watermark
1
2
3
To change the print settings from your software
application, access printer properties. See “Printing a
Click the Extras tab, and click the Edit button in the
Watermark section. The Edit Watermark window
appears.
Enter a text message in the Watermark Message box.
You can enter up to 40 characters. The message displays
in the preview window.
When the First Page Only box is checked, the watermark
prints on the first page only.
4
Select watermark options.
You can select the font name, style, size, or grayscale level
from the Font Attributes section and set the angle of the
watermark from the Message Angle section.
5
6
Click Add to add a new watermark to the list.
When you have finished editing, click OK and start
printing.
To stop printing the watermark, select (No Watermark) from
the Watermark drop-down list.
20
Advanced Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Page Overlay
After an overlay has been created, it is ready to be printed with
your document. To print an overlay with a document:
Using Overlays
1
2
Create or open the document you want to print.
What is an Overlay?
To change the print settings from your software
application, access printer properties. See “Printing a
An overlay is text and/or images stored in the computer hard
disk drive (HDD) as a special file format that can be printed on
any document. Overlays are often used to take the place of
preprinted forms and letterhead paper. Rather than using
preprinted letterhead, you can create an overlay containing the
exact same information that is currently on your letterhead. To
print a letter with your company’s letterhead, you do not need
to load preprinted letterhead paper in the printer. You need only
tell the printer to print the letterhead overlay on your
document.
Dear ABC
3
4
Click the Extras tab.
Select the desired overlay from the Overlay drop-down
list box.
If the overlay file you want does not appear in the
Overlay list, click Edit button and Load Overlay, and
select the overlay file.
Regards
WORLD BEST
5
If you have stored the overlay file you want to use in an
external source, you can also load the file when you access
the Load Overlay window.
Creating a New Page Overlay
To use a page overlay, you must create a new page overlay
containing your logo or image.
After you select the file, click Open. The file appears in the
Overlay List box and is available for printing. Select the
overlay from the Overlay List box.
6
7
If necessary, click Confirm Page Overlay When
Printing. If this box is checked, a message window
appears each time you submit a document for printing,
asking you to confirm your wish to print an overlay on your
document.
1
Create or open a document containing text or an image for
use in a new page overlay. Position the items exactly as
you wish them to appear when printed as an overlay.
To save the document as an overlay, access printer
properties. See “Printing a Document” on page 12.
Click the Extras tab, and click Edit button in the Overlay
section.
WORLD BEST
2
3
If this box is not checked and an overlay has been
selected, the overlay automatically prints with your
document.
4
5
In the Edit Overlay window, click Create Overlay.
Click OK or Yes until printing begins.
In the Create Overlay window, type a name of up to eight
characters in the File name box. Select the destination
path, if necessary. (The default is C:\Formover).
The selected overlay downloads with your print job and
prints on your document.
6
7
Click Save. The name appears on the Overlay List box.
NOTE: The resolution of the overlay document must be the
same as that of the document you will print with the overlay.
Click OK or Yes to finish creating.
The file is not printed. Instead it is stored on your
computer hard disk drive.
Deleting a Page Overlay
You can delete page overlays that you no longer use.
NOTE: The overlay document size must be the same as the
documents you print with the overlay. Do not create an overlay
with a watermark.
1
2
3
In the printer properties window, click the Extras tab.
Click the Edit button in the Overlay section.
Select the overlay you want to delete from the Overlay
List box.
4
5
6
Click Delete Overlay.
When a confirming message window appears, click Yes
.
Click OK until you exit the Print window.
21
Advanced Printing
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced
You can use advanced settings by clicking the Advanced
button.
4
Using Windows
PostScript Driver
(SCX-4725FN only)
If you want to use the PostScript driver provided with your
system CD-ROM to print a document.
PPDs, in combination with the PostScript driver, access printer
features and allow the computer to communicate with the
printer. An installation program for the PPDs is provided on the
supplied software CD-ROM.
This chapter includes:
Printer Settings
You can use the printer properties window, which allows you to
access all of the printer options you need when using your
printer. When the printer properties are displayed, you can
review and change the settings needed for your print job.
•
•
•
Paper/Output this option allows you to select the size of the
paper loaded in the tray.
Graphic this option allows you to adjust the print quality for
your specific printing needs.
Document Options this options allow you to set the PostScript
options or printer features.
Your printer properties window may differ, depending on your
operating system. This Software User’s Guide shows the
Properties window for Windows XP.
Your printer driver Properties window that appears in this
User’s Guide may differ depending on the printer in use.
NOTES
:
Using Help
• Most Windows applications will override settings you specify
in the printer driver. Change all print settings available in the
software application first, and change any remaining settings
using the printer driver.
You can click
from the upper right corner of the window, and
then click on any setting.
• The settings you change remain in effect only while you are
using the current program. To make your changes
permanent, make them in the Printers folder.
• The following procedure is for Windows XP. For other
Windows OS, refer to the corresponding Windows User's
Guide or online help.
1. Click the Windows Start button.
2. Select Printers and Faxes.
3. Select your printer driver icon.
4. Right-click on the printer driver icon and select
Printing Preferences.
5. Change the settings on each tab, click OK.
22
Using Windows PostScript Driver (SCX-4725FN only)
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Sharing the Printer
Locally
You can connect the printer directly to a selected computer,
which is called “host computer,” on the network.
Setting Up a Host Computer
1
2
3
4
5
6
Start Windows.
From the Start menu select Printers and Faxes
.
Double-click your printer driver icon
.
From the Printer menu, select Sharing
.
The following procedure is for Windows XP. For other Windows
OS, refer to the corresponding Windows User's Guide or online
help.
Check the Share this printer box.
Fill in the Shared Name field, and then click OK
.
NOTES
:
• Check the Operating System(s) that are compatible with
your printer. Please refer to the OS Compatibility section of
Printer Specifications in your Printer User’s Guide.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
Setting Up a Client Computer
1
2
3
4
5
6
7
8
9
Right-click the Windows Start button and select Explorer
Open your network folder in the left column.
Click the shared name.
.
From the Start menu select Printers and Faxes
Double-click your printer driver icon
From the Printer menu, select Properties
From the Ports tab, click Add Port
Select Local Port and click New Port
Fill in the Enter a port name field with the shared name.
.
.
.
.
.
10Click OK and click Close.
11Click Apply and click OK.
23
Sharing the Printer Locally
Download from Www.Somanuals.com. All Manuals Search And Download.
The Smart Panel program displays the current status of the
printer, various information, lets you change settings and the
level of toner remaining in the toner cartridge(s).
6
Using Smart Panel
Smart Panel is a program that monitors and informs you of the
status of the printer, and allows you to customize the printer’s
settings. Smart Panel is installed automatically when you
install the printer software.
2
3
NOTES:
4
1
• To use the this program, you need:
5
- Windows 98 or higher (Windows NT 4.0 can be used only
for network-supported printers.) To check for Operating
System(s) that are compatible with your printer, refer to
Printer Specifications in your Printer User’s Guide.
- Internet Explorer version 5.0 or higher for flash animation
in HTML Help.
• If you need to know the exact name of your printer, you can
check the supplied CD-ROM.
1
Toner Level
You can view the level of toner remaining in the toner
cartridge(s). The printer and the number of the toner cartridge(s)
shown above window may differ depending on the printer in use.
2
Buy Now
You can order replacement toner cartridge online.
3
Troubleshooting Guide
You can view Help to solve problems.
Understanding Smart Panel
If an error occurs while printing, Smart Panel appears
automatically, showing the error. You can also launch Smart
Panel manually from the Windows task bar. Double-click the
Smart Panel icon on the Windows task bar.
4
Printer Setting
You can configure various printer settings in the Printer Settings
Utility window.
NOTES: If you connect your printer to a network, the
SyncThru Web Service window appears instead of the
Printer Settings Utility window.
Double click this icon.
Or, from the Start menu, select Programs or All Programs
5
Driver Setting
→
your printer driver name
→
Smart Panel.
You can use the printer properties window, which allows you to
access all of the printer options you need for using your
NOTES:
• If you have already installed more than one Samsung
printer, first select the printer model you want in order to
use the corresponding Smart Panel. Right-click the Smart
Panel icon on the Windows task bar and select your printer
name
.
Opening the Troubleshooting
Guide
• The Smart Panel window and its contents shown in this
Software User’s Guide may differ depending on the printer in
use.
Using the troubleshooting guide, you can view solutions for
error status problems.
Right-click the Smart Panel icon on the Windows task bar and
select Troubleshooting Guide
.
24
Using Smart Panel
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Printer Settings Utility
Changing the Smart Panel
Program Settings
Using the Printer Settings Utility, you can configure and check
print settings.
Right-click the Smart Panel icon on the Windows task bar and
1
Right-click the Smart Panel icon on the Windows task bar
and select Printer Setting
select Options
.
.
The following window opens.
2
3
Change the settings.
To send the changes to the printer, click the Apply(or Send)
button.
NOTES: If you connect your printer to a network, the
SyncThru Web Service window appears instead of the
Printer Settings Utility window.
Using Onscreen Help File
Use the help feature by refering the window which appears
when you click the Help button at the bottom.
•
Display when job is finished for network printer: The
computer shows the Smart Panel popup window or
balloon when your job is complete. (Only for a network
supported printer.)
•
•
Display when error occurs during printing: The
computer shows the Smart Panel popup window or
balloon when an error occurs during printing.
Display with: You can select how the computer shows
you a message. If you select Popup window (smart
panel), the message appears in the Smart Panel pop
window.
•
•
Launch Job Monitor when the job is saved in the
printer: If you store print jobs on the printer’s hard disk,
the computer opens the Job Monitor window. (Only for a
network supported printer with a built-in hard disk.)
Schedule an automatic status checking every: The
computer updates the printer status regularly. Setting the
value close to 1 second causes the computer to check the
printer status more frequently, thereby allowing a faster
response to any printer error.
25
Using Smart Panel
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Scanning
Scanning with your machine lets you turn pictures and text into
digital files on your computer. Then you can fax or e-mail the
files, display them on your web site or use them to create
projects that you can print using Samsung SmarThru software
or the WIA driver.
Scanning Using Samsung
SmarThru
Samsung SmarThru is the accompanying software for your
machine.
This chapter includes:
Uninstalling Samsung SmarThru
NOTE: Before beginning uninstallation, ensure that all
applications are closed on your computer.
NOTES
:
1
2
3
4
From the Start menu, select Programs
Select SmarThru 4, and then select Uninstall SmarThru 4
When your computer asks you to confirm, click OK
Click Finish
.
• Check the Operating System(s) that are compatible
with your printer. Please refer to the OS Compatibility
section of Printer Specifications in your Printer User’s
Guide.
• You can check your printer name in the supplied CD-
ROM.
.
.
.
• The maximum resolution that can be achieved
depends upon various factors, including computer
speed, available disk space, memory, the size of the
image being scanned, and bit depth settings. Thus,
depending on your system and what you are scanning,
you may not be able to scan at certain resolutions,
especially using enhanced dpi.
You may be prompted to restart your computer. In this case
you must shut the computer down and then restart it before
the changes will be saved.
26
Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Click Scan To. The Scan To menu bar appears on the
SmarThru 4 window.
Using Samsung SmarThru
Follow these steps to start scanning using the SmarThru:
1
2
3
Make sure that your machine and computer are turned on
and properly connected to each other.
Place your photograph or page on the document glass
or ADF.
Scan To
menu bar
Once you have installed Samsung SmarThru, you will see
the SmarThru 4 icon on your desktop. Double-click the
SmarThru 4 icon.
Adjust the
scan settings.
Double-click this icon.
Click to start
scanning.
The SmarThru 4 window opens.
Scan To lets you use the following services:
•Application
Make sure that your
printer is selected.
Scanning an image and placing it in an image editor
application, such as Paint or Adobe Photoshop.
•E-mail
Scanning an image and emailing it. Allows you to scan an
image, preview it, and email it.
•Scan To
NOTE: To send an image by e-mail, you must have a mail
client program, like Outlook Express, which has been set up
with your e-mail account.
Allows you to scan an image and save it to an application
or folder, email it, or publish it on a web site.
•Image
Allows you to edit an image you have saved as a graphic
file and send it to a selected application or folder, email it,
or publish it on a web site.
•Folder
Scanning an image and saving it to a folder. Allows you to
scan an image, preview it, and save it to the folder of your
choice.
•Copy
Allows you to produce professional quality copies. You can
make black and white or color copies of an image if your
machine supports it, and customize the copy settings.
•OCR
Scanning an image and performing text recognition.
Allows you to scan an image, preview it, and send it to the
OCR program for text recognition.
•Print
Allows you to print images you have saved. You can print
images in black and white or color mode if your machine
supports it.
- Recommended Scan Option for OCR
- Resolution: 200 or 300 dpi
- Image Type: Grayscale or Black & White
•Fax
•Web
Allows you to fax images or files you have saved on your
computer. This is available when your machine supports
the fax feature.
Scanning an image, previewing it, and publishing it on a
web site, using the specified file format for the image you
want to publish.
27
Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
•Settings
Customizing settings of Scan To basic functions. Allows
Scanning Using the WIA Driver
you to customize settings for Application E-mail, OCR,
,
and Web functions.
Your machine also supports the Windows Image Acquisition
(WIA) driver for scanning images. WIA is one of the standard
components provided by Microsoft® Windows® XP and works
with digital cameras and scanners. Unlike the TWAIN driver, the
WIA driver allows you to scan and easily manipulate images
without using additional software.
5
6
Click the service icon according to your job.
SmarThru 4 opens for the selected service. Adjust the
scan settings.
7
To start scanning, click Scan.
NOTE: The WIA driver works only on Windows XP with USB
port.
NOTE: If you want to cancel the scan job, click Cancel
.
1
2
Load the document(s) face up into the ADF.
OR
Using Onscreen Help File
For more information about SmarThru, click
corner of the window. The SmarThru Help window opens and
allows you to view onscreen help supplied on the SmarThru
program.
Place a single document face down on the document
glass.
From the Start menu on your desktop window, select
at the top right
Settings
,
Control Panel, and then Scanners and
Cameras
.
3
4
Double click your scanner driver icon. The Scanner and
Camera Wizard launches.
Choose your scanning preferences and click Preview to
see how your preferences affect the picture.
Scanning Process with TWAIN-
enabled Software
5
6
Click Next.
Enter a picture name, and select a file format and
destination to save the picture.
If you want to scan documents using other software, you will
need to use TWAIN-compliant software, such as Adobe
PhotoDeluxe or Adobe Photoshop. The first time you scan with
your machine, select it as your TWAIN source in the application
you use.
7
Follow the on-screen instructions to edit the picture after it
is copied to your computer.
NOTE: If you want to cancel the scan job, press the Cancel
button on the Scanner and Camera Wizard.
The basic scanning process involves a number of steps:
1
2
Make sure that your machine and computer are turned on
and properly connected to each other.
Load the document(s) face up into the ADF.
OR
Place a single document face down on the document
glass.
3
4
5
Open an application, such as PhotoDeluxe or Photoshop.
Open the TWAIN window and set the scan options.
Scan and save your scanned image.
NOTE: You need to follow the program’s instructions for
acquiring an image. Please refer to the user’s guide of the
application.
28
Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Using Your Printer in
Linux
Installing the Unified Linux
Driver
You can use your machine in a Linux environment.
Installing the Unified Linux Driver
1
Make sure that you connect your machine to your
computer. Turn both the computer and the machine on.
When the Administrator Login window appears, type in
root in the Login field and enter the system password.
This chapter includes:
2
NOTE: You must log in as a super user (root) to install the
printer software. If you are not a super user, ask your system
administrator.
3
Insert the printer software CD-ROM. The CD-ROM will
automatically run.
If the CD-ROM does not automatically run, click the
icon at the bottom of the desktop. When the Terminal
screen appears, type in:
Getting Started
The supplied CD-ROM provides you with Samsung’s Unified
Linux Driver package for using your machine with a Linux
computer.
If the CD-ROM is secondary master and the location to
mount is /mnt/cdrom,
[root@localhost root]#mount -t iso9660 /dev/hdc /mnt/
cdrom
Samsung’s Unified Linux Driver package contains printer and
scanner drivers, providing the ability to print documents and
scan images. The package also delivers powerful applications
for configuring your machine and further processing of the
scanned documents.
[root@localhost root]#cd /mnt/cdrom/Linux
[root@localhost root]#./install.sh
After the driver is installed on your Linux system, the driver
package allows you to monitor a number of machine devices via
fast ECP parallel ports and USB simultaneously.
NOTE: The installation program runs automatically if you
have an autorun software package installed and configured.
The acquired documents can then be edited, printed on the
same local or network machine devices, sent by e-mail,
uploaded to an FTP site, or transferred to an external OCR
system.
4
When the welcome screen appears, click Next.
The Unified Linux Driver package is supplied with a smart and
flexible installation program. You don't need to search for
additional components that might be necessary for the Unified
Linux Driver software: all required packages will be carried onto
your system and installed automatically; this is possible on a
wide set of the most popular Linux clones.
29
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
5
When the installation is complete, click Finish.
Uninstalling the Unified Linux Driver
1
When the Administrator Login window appears, type in
root in the Login field and enter the system password.
NOTE: You must log in as a super user (root) to install the
printer software. If you are not a super user, ask your system
administrator.
2
Insert the printer software CD-ROM. The CD-ROM will
automatically run.
If the CD-ROM does not automatically run, click the
icon at the bottom of the desktop. When the Terminal
screen appears, type in:
If the CD-ROM is secondary master and the location to
mount is /mnt/cdrom,
The installation program has added the Unified Driver
Configurator desktop icon and Samsung Unified Driver
group to the system menu for your convenience. If you
have any difficulties, consult the onscreen help that is
available through your system menu or can otherwise be
called from the driver package windows applications,
such as Unified Driver Configurator or Image
[root@localhost root]#mount -t iso9660 /dev/hdc /mnt/
cdrom
[root@localhost root]#cd /mnt/cdrom/Linux
[root@localhost root]#./uninstall.sh
Manager
.
NOTE: The installation program runs automatically if you
have an autorun software package installed and configured.
3
4
Click Uninstall
.
Click Next
.
5
Click Finish.
30
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
Printers Configuration
Printers configuration has the two tabs: Printers and Classes
.
Using the Unified Driver
Configurator
Printers Tab
You can see the current system’s printer configuration by
clicking on the printer icon button on the left side of the Unified
Driver Configurator window.
Unified Linux Driver Configurator is a tool primarily intended for
configuring Printer or MFP devices. Since an MFP device
combines the printer and scanner, the Unified Linux Driver
Configurator provides options logically grouped for printer and
scanner functions. There is also a special MFP port option
responsible for the regulation of access to an MFP printer and
scanner via a single I/O channel.
Switches to Printer
configuration.
After installing the Unified Linux driver, the Unified Linux Driver
Configurator icon will automatically be created on your desktop.
Shows all of the
installed printer.
Opening the Unified Driver
Configurator
Shows the status,
model name and
URI of your printer.
1
Double-click Unified Driver Configurator on the
desktop.
You can also click the Startup Menu icon and select
Samsung Unified Driver and then Unified Driver
Configurator
Press each button on the Modules pane to switch to the
corresponding configuration window.
.
You can use the following printer control buttons:
2
•
•
•
•
Refresh: renews the available printers list.
Add Printer: allows you to add a new printer.
Remove Printer: removes the selected printer.
Printers Configuration button
Scanners Configuration button
Ports Configuration button
Set as Default: sets the current printer as a default
printer.
•
•
Stop/Start: stops/starts the printer.
Test: allows you to print a test page to check if the
machine is working properly.
•
Properties: allows you to view and change the printer
You can use the onscreen help by clicking Help
After changing the configurations, click Exit to close the
Unified Driver Configurator.
.
3
31
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
Classes Tab
The Classes tab shows a list of available printer classes.
Ports Configuration
In this window, you can view the list of available ports, check
the status of each port and release a port that is stalled in busy
state when its owner is terminated for any reason.
Shows all of the
printer classes.
Switches to
ports
configuration.
Shows all of the
available ports.
Shows the status of the
class and the number of
printers in the class.
Shows the port type,
device connected to
the port and status
•
•
•
Refresh : Renews the classes list.
Add Class... : Allows you to add a new printer class.
Remove Class : Removes the selected printer class.
•
•
Refresh : Renews the available ports list.
Release port : Releases the selected port.
Sharing Ports Between Printers and Scanners
Scanners Configuration
In this window, you can monitor the activity of scanner devices,
view a list of installed Samsung MFP devices, change device
properties, and scan images.
Your machine may be connected to a host computer via the
parallel port or USB port. Since the MFP device contains more
than one device (printer and scanner), it is necessary to
organize proper access of “consumer” applications to these
devices via the single I/O port.
The Samsung Unified Linux Driver package provides an
appropriate port sharing mechanism that is used by Samsung
printer and scanner drivers. The drivers address their devices
via so-called MFP ports. The current status of any MFP port can
be viewed via the Ports Configuration. The port sharing
prevents you from accessing one functional block of the MFP
device, while another block is in use.
Switches to
Scanners
configuration.
Shows all of the
installed scanners.
When you install a new MFP device onto your system, it is
strongly recommended you do this with the assistance of an
Unified Driver Configurator. In this case you will be asked to
choose I/O port for the new device. This choice will provide the
most suitable configuration for MFP’s functionality. For MFP
scanners I/O ports are being chosen by scanner drivers
automatically, so proper settings are applied by default.
Shows the vendor,
model name and type
of your scanner.
•
•
Properties... : Allows you to change the scan properties
Drivers... : Allows you to monitor the activity of the scan drivers.
32
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring Printer Properties
Printing a Document
Using the properties window provided by the Printers
configuration, you can change the various properties for your
machine as a printer.
Printing from Applications
There are a lot of Linux applications that you are allowed to
print from using Common UNIX Printing System (CUPS). You
can print on your machine from any such application.
1
Open the Unified Driver Configurator.
If necessary, switch to Printers configuration.
Select your machine on the available printers list and click
2
3
1
From the application you are using, select Print from the
File menu.
Properties
.
The Printer Properties window opens.
2
3
Select Print directly using lpr
In the LPR GUI window, select the model name of your
machine from the Printer list and click Properties
.
.
Click.
The following five tabs display at the top of the window:
•
•
General: allows you to change the printer location and
name. The name entered in this tab displays on the
printer list in Printers configuration.
Connection: allows you to view or select another port.
If you change the printer port from USB to parallel or
vice versa while in use, you must re-configure the
printer port in this tab.
4
Change the printer and print job properties.
•
•
•
Driver: allows you to view or select another printer
driver. By clicking Options, you can set the default
device options.
Jobs: shows the list of print jobs. Click Cancel job to
cancel the selected job and select the Show completed
jobs check box to see previous jobs on the job list.
Classes: shows the class that your printer is in. Click
Add to Class to add your printer to a specific class or
click Remove from Class to remove the printer from
the selected class.
4
Click OK to apply the changes and close the Printer
Properties Window.
33
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
The following four tabs display at the top of the window.
•
General - allows you to change the paper size, the
paper type, and the orientation of the documents,
enables the duplex feature, adds start and end banners,
and changes the number of pages per sheet.
Text - allows you to specify the page margins and set
the text options, such as spacing or columns.
Graphics - allows you to set image options that are
used when printing images/files, such as color options,
image size, or image position.
Scanning a Document
You can scan a document using the Unified Driver Configurator
window.
•
•
1
Double-click the Unified Driver Configurator on your
desktop.
2
3
Click the
button to switch to Scanners Configuration.
Select the scanner on the list.
•
Device: allows you to set the print resolution, paper
source, and destination.
5
Click Apply to apply the changes and close the Properties
window.
6
7
Click OK in the LPR GUI window to start printing.
The Printing window appears, allowing you to monitor the
status of your print job.
Click your
scanner.
To abort the current job, click Cancel
.
Printing Files
You can print many different types of files on the Samsung
machine device using the standard CUPS way - directly from
the command line interface. The CUPS lpr utility allows you do
that. But the drivers package replaces the standard lpr tool by
a much more user-friendly LPR GUI program.
To print any document file:
1
Type lpr <file_name> from the Linux shell command
line and press Enter. The LPR GUI window appears.
When you have only one MFP device and it is connected
to the computer and turned on, your scanner appears on
the list and is automatically selected.
When you type only lpr and press Enter, the Select
file(s) to print window appears first. Just select any files
If you have two or more scanners attached to your
computer, you can select any scanner to work at any
time. For example, while acquisition is in progress on the
first scanner, you may select the second scanner, set the
device options and start the image acquisition
simultaneously.
you want to print and click Open
In the LPR GUI window, select your printer from the list,
and change the printer and print job properties.
.
2
3
For details about the properties window, see page 33.
Click OK to start printing.
4
5
Click Properties.
Load the document to be scanned face up into the ADF
(Automatic Document Feeder) or face down on the
document glass.
6
Click Preview in the Scanner Properties window.
34
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
The document is scanned and the image preview appears
in the Preview Pane.
10When you are finished, click Save on the toolbar.
11Select the file directory where you want to save the image
and enter the file name.
12Click Save.
Adding Job Type Settings
You can save your scan option settings to retrieve for a later
scanning.
To save a new Job Type setting:
1
2
3
4
Change the options from the Scanner Properties window.
Click Save As
Enter the name for your setting.
Click OK
Drag the pointer to
set the image area
to be scanned.
.
.
Your setting is added to the Saved Settings drop-down
list.
To save a Job Type setting for the next scan job:
1
Select the setting you want to use from the Job Type drop-
down list.
7
Change the scan options in the Image Quality and Scan
Area sections.
2
The next time you open the Scanner Properties window,
the saved setting is automatically selected for the scan
job.
•
Image Quality: allows you to select the color
composition and the scan resolution for the image.
To delete a Job Type setting:
1
•
Scan Area: allows you to select the page size. The
Advanced button enables you to set the page size
manually.
Select the setting you want to delete from the Job Type
drop-down list.
2
Click Delete
.
If you want to use one of the preset scan option settings,
select from the Job Type drop-down list. For details about
The setting is deleted from the list.
You can restore the default setting for the scan options
Using the Image Manager
The Image Manager application provides you with menu
commands and tools to edit your scanned image.
by clicking Default
.
8
9
When you have finished, click Scan to start scanning.
The status bar appears on the bottom left of the window
to show you the progress of the scan. To cancel scanning,
click Cancel
.
The scanned image appears in the new Image Manager
tab.
Use these tools to
edit the image.
If you want to edit the scanned image, use the toolbar.
For further details about editing an image, see page 35.
35
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
You can use the following tools to edit the image:
Tools Function
Saves the image.
Cancels your last action.
Restores the action you canceled.
Allows you to scroll through the image.
Crops the selected image area.
Zooms the image out.
Zooms the image in.
Allows you to scale the image size; you can
enter the size manually, or set the rate to
scale proportionally, vertically, or
horizontally.
Allows you to rotate the image; you can
select the number of degrees from the drop-
down list.
Allows you to flip the image vertically or
horizontally.
Allows you to adjust the brightness or
contrast of the image, or to invert the
image.
Shows the properties of the image.
For further details about the Image Manager application, refer
to the onscreen help.
36
Using Your Printer in Linux
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Using Your Printer with
a Macintosh
(SCX-4725FN only)
Your machine supports Macintosh systems with a built-in USB
interface or a 10/100 Base-TX network interface card. When
you print a file from a Macintosh computer, you can use the
PostScript driver by installing the PPD file.
Installing Software for
Macintosh
The PostScript driver CD-ROM that came with your machine
provides you with the PPD file to use the PS driver, Apple
LaserWriter driver, for printing on a Macintosh computer.
Also, it provides you with the Twain driver for scanning on a
Macintosh computer.
Install the Printer driver
1
Connect your machine to the computer using the USB
cable or the Ethernet cable.
Turn on your computer and the machine.
NOTE: Some printers do not support a network
interface. Make sure that your printer supports a
network interface by referring to Printer Specifications
in your Printer User’s Guide.
2
3
Insert the PostScript driver CD-ROM which came with your
machine into the CD-ROM drive.
4
Double-click the Samsung MFP on your Macintosh
desktop.
Double-click the MAC_Installer folder.
This chapter includes:
• Printing
5
6
7
8
9
Double-click the MAC_Printer folder.
Double-click the Samsung MFP Installer OSX icon.
Click Continue
.
• Scanning
Click Install
.
10After the installation is finished, click Quit.
Uninstalling the Printer driver
Uninstall is required if you are upgrading the software, or if
installation fails.
1
2
Insert the PostScript driver CD-ROM which came with your
machine into the CD-ROM drive.
Double-click the Samsung MFP on your Macintosh
desktop.
3
4
5
6
7
8
Double-click the MAC_Installer folder.
Double-click the MAC_Printer folder.
Double-click the Samsung MFP Installer OSX icon.
Click Continue
Select Uninstall and then click Uninstall
When the uninstallation is done, click Quit
.
.
.
37
Using Your Printer with a Macintosh (SCX-4725FN only)
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the Scan driver
1
2
3
Make sure that you connect your printer to the computer.
Turn on your computer and printer.
Insert the CD-ROM which came with your printer into the
CD-ROM drive.
Double-click CD-ROM icon that appears on your
Macintosh desktop.
Setting Up the Printer
Set up for your printer will be different depending on which
cable you use to connect the printer to your computer—the
network cable or the USB cable.
4
5
6
7
8
9
Double-click the MAC_Installer folder.
For a Network-connected Macintosh
Double-click the MAC_Twain folder.
Double-click the Samsung ScanThru Installer icon.
NOTE Some printers do not support a network
:
Enter the password and click OK
Click Continue
Click Install
.
interface. Before connecting your printer, make sure
that your printer supports a network interface by
referring to Printer Specifications in your Printer User’s
Guide.
.
.
10Click Continue.
11After the installation is finished, click Quit.
1
2
Follow the instructions on “Installing Software for
Macintosh” on page 37 to install the PPD file on your
computer.
Open Print Center or Printer Setup Utility from the
Utilities folder.
Uninstalling the Scan driver
1
Insert the CD-ROM which came with your printer into the
CD-ROM drive.
2
Double-click CD-ROM icon that appears on your
Macintosh desktop.
3
4
Click Add on the Printer List.
3
4
5
6
7
8
Double-click the MAC_Installer folder.
Select the AppleTalk tab.
Double-click the MAC_Twain folder.
The name of your machine appears on the list. Select
SEC000xxxxxxxxx from the printer box, where the
xxxxxxxxx varies depending on your machine.
Double-click the Samsung ScanThru Installer icon.
Enter the password and click OK
Click Continue
Select Uninstall from the Installation Type and then Click
Uninstall
Click Continue
.
5
6
Click Add
If Auto Select does not work properly, select Samsung in
Printer Model and your printer name in Model Name
.
.
.
.
Your machine appears on the Printer List and is set as the
default printer.
9
.
10When the uninstallation is done, click Quit.
For a USB-connected Macintosh
1
Follow the instructions on “Installing Software for
Macintosh” on page 37 to install the PPD file on your
computer.
2
Open Print Center or Printer Setup Utility from the
Utilities folder.
3
4
5
6
Click Add on the Printer List.
Select the USB tab.
Select your printer name and click Add
If Auto Select does not work properly, select Samsung in
Printer Model and your printer name in Model Name
.
.
Your machine appears on the Printer List and is set as the
default printer.
38
Using Your Printer with a Macintosh (SCX-4725FN only)
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Printer Settings
You can use advanced printing features when using your
printer.
Printing
From your Macintosh application, select Print from the File
menu. The printer name which appears in the printer properties
window may differ depending on the printer in use. Except for
the name, the composition of the printer properties window is
similar.
NOTES
:
• The Macintosh printer’s properties window that appears in
this User’s Guide may differ depending on the printer in use.
However the composition of the printer properties window is
similar.
• You can check your printer name in the supplied CD-
ROM.
Layout Setting
The Layout tab provides options to adjust how the document
appears on the printed page. You can print multiple pages on
one sheet of paper.
Select Layout from the Presets drop-down list to access the
following features. For details, see “Printing Multiple Pages on
One Sheet of Paper” on the next column.
Printing a Document
When you print with a Macintosh, you need to check the printer
software setting in each application you use. Follow these steps
to print from a Macintosh.
1
2
3
Open a Macintosh application and select the file you want
to print.
Open the File menu and click Page Setup (Document
Setup in some applications).
Choose your paper size, orientation, scaling, and other
options and click OK
.
Make sure that your
printer is selected.
▲
Mac OS 10.3
▲
Mac OS 10.3
4
5
Open the File menu and click Print.
Choose the number of copies you want and indicate which
pages you want to print.
6
Click Print when you finish setting the options.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Features Setting
The Printer Features tab provides options for selecting the
paper type and adjusting print quality.
Printing Multiple Pages on One Sheet
of Paper
You can print more than one page on a single sheet of paper.
This feature provides a cost-effective way to print draft pages.
Select Printer Features from the Presets drop-down list to
access the following features:
1
2
From your Macintosh application, select Print from the
File menu.
Select Layout
.
▲
Mac OS 10.3
Image Mode
Image Mode allows the user to enhance printouts. The available
options are Normal and Text Enhance.
Fit to Page
This printer feature allows you to scale your print job to any
selected paper size regardless of the digital document size. This
can be useful when you want to check fine details on a small
document.
Paper Type
▲
Mac OS 10.3
Set Type to correspond to the paper loaded in the tray from
which you want to print. This will let you get the best quality
printout. If you load a different type of print material, select the
corresponding paper type.
3
4
Select the number of pages you want to print on one sheet
of paper on the Pages per Sheet drop-down list.
Select the page order from the Layout Direction option.
Resolution(Quality)
To print a border around each page on the sheet, select
the option you want from the Border drop-down list.
Click Print, and the printer prints the selected number of
pages on one side of each page.
The Resolution options you can select may vary
depending on your printer model. You can select the
printing resolution. The higher the setting, the sharper the clarity
of printed characters and graphics. The higher setting also may
increase the time it takes to print a document.
5
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Scanning
If you want to scan documents using other software, you will
need to use TWAIN-compliant software, such as Adobe
PhotoDeluxe or Adobe Photoshop. The first time you scan with
your machine, select it as your TWAIN source in the application
you use.
The basic scanning process involves a number of steps:
• Place your photograph or page on the document glass or
ADF.
• Open an application, such as PhotoDeluxe or Photoshop.
• Open the TWAIN window and set the scan options.
• Scan and save your scanned image.
NOTE: You need to follow the program’s instructions for
acquiring an image. Please refer to the User’s Guide of the
application.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE SECTION
INDEX
Windows 13
Linux
poster, print 19
PostScript driver
installing 22
print
A
advanced printing, use 18
driver, install 29
printer properties 33
printing 33
document 12
fit to page 19
from Macintosh 39
from Windows 12
N-up
Macintosh 40
Windows 18
overlay 21
C
scanning 34
canceling
scan 28
M
Macintosh
driver
D
document, print
Macintosh 39
Windows 12
install 37
uninstall 37
printing 39
poster 20
PRN 12
scaling 19
scanning 41
setting up the printer 38
MFP driver, install
Linux 29
watermark 20
print resolution 34
printer driver, install
Linux 29
E
Extras properties, set 16
printer properties
Linux 33
F
N
printer properties, set
Macintosh 39
printer resolution, set
Macintosh 40
Windows 15
favorites settings, use 17
n-up printing
Macintosh 40
Windows 18
G
Graphics properties, set 15
O
printer software
install
orientation, print 34
Windows 13
overlay
H
Macintosh 37
Windows
uninstall
create 21
delete 21
print 21
Macintosh 37
Windows 11
printing
I
install
from Linux 33
printer driver
Macintosh 37
P
Windows
Paper properties, set 14
paper size, set 14
print 34
R
installing
Linux software 29
resolution
printing 34
paper source, set 34
Windows 14
paper type, set
Macintosh 40
L
S
Layout properties, set
Macintosh 39
print 34
scanning
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Linux 34
SmarThru 26
TWAIN 28
WIA driver 28
scanning from Macintosh 41
setting
darkness 15
favorites 17
image mode 15
resolution
Macintosh 40
Windows 15
toner save 15
true-type option 15
software
install
Macintosh 37
Windows
reinstall
Windows 10
system requirements
Macintosh 37
uninstall
Macintosh 37
Windows 11
status monitor, use 24
T
toner save, set 15
TWAIN, scan 28
U
uninstall, software
Macintosh 37
Windows 11
uninstalling
MFP driver
Linux 30
W
watermark
create 20
delete 20
edit 20
print 20
WIA, scan 28
43
Download from Www.Somanuals.com. All Manuals Search And Download.
|