DVD Player
DVD-FP580 / FP580W
DVD-F1080 / F1080W
www.samsung.com/ca
CA
AK68-01503G(01)
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
This symbol indicates that
This symbol indicates that there are
important operating and
maintenance instructions in the
literature accompanying this unit.
dangerous voltage consisting a risk
of electric shock is present within
this unit.
Do not install this equipment in a confined space such as a bookcase or similar unit.
WARNING :
• To prevent damage which may result in fire or electric shock hazard, do not expose this appliance
to rain or moisture.
• If this power supply is used at 240V ac, a suitable plug adapter should be used.
CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Note to CATV system installer : This reminder is provided to call CATV system installer’s attention to
Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I) that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building as close to the point of cable entry as practical.
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to
other equipment. To prevent electromagnetic interference with electric appliances, such as radios and
televisions, use shielded cables and connectors for connections.
Caution : FCC regulations state that any unauthorized changes or modifications to this equipment may void
the user’s authority to operate it.
FCC NOTE (for U.S.A):
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on.
The user is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect this equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This class B digital apparatus meets all requirements of the Canadian Interference --
Causing Equipment Regulations.
CALIFORNIA USA ONLY :
This Perchlorate warning applies only to primary CR (Maganese Dioxide) Lithium coin cells in the product sold
or distributed ONLY in California USA “Perchlorate Material - special handling may apply , See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
CLASS 1
LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1
LASER APPARAT
PRODUCTO LÁSER CLASE 1
ENG-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVER AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
Note:
• This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere.
• This DVD player is designed and manufactured to respond to the Region Management Information.
If the Region number of a DVD disc does not correspond to the Region number of this DVD player,
the DVD player cannot play the disc.
• The product unit accompanying this user manual is licensed under certain intellectual property rights
of certain third parties. In particular, this product is licensed under the following US patents:
5,060,220 5,457,669 5,561,649 5,705,762 5,987,417 6,043,912 6,222,983 6,272,096 6,377,524
6,377,531 6,385,587 6,389,570 6,408,408 6,466,532 6,473,736 6,477,501 6,480,829 6,556,520
6,556,521 6,556,522 6,578,163 6,594,208 6,631,110 6,658,588 6,674,697 6,674,957 6,687,455
6,697,307 6,707,985 6,721,243 6,721,493 6,728,474 6,741,535 6,744,713 6,744,972 6,765,853
6,765,853 6,771,890 6,771,891 6 775,465 6,778,755 6,788,629 6,788,630 6,795,637 6,810,201
6,862,256 6,868,054 6,894,963 6,937,552.
This license is limited to private non-commercial use by end-user consumers for licensed contents.
No rights are granted for commercial use. The license does not cover any product unit other than this
product unit and the license does not extend to any unlicensed product unit or process conforming to
ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit.
The license only covers the use of this product unit to encode and/or decode audio files conforming
to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product
features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
Handling Cautions
• Before connecting other components to this player, be sure to turn them all off.
• Do not move the player while a disc is being played, or the disc may be scratched or broken, and the player’s
internal parts may be damaged.
• Do not put a flower vase filled with water or any small metal objects on the player.
• Be careful not to put your hand into the disc tray.
• Do not place anything other than the disc in the disc tray.
• Exterior interference such as lightning and static electricity can affect normal operation of this player.
If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the
AC power cord to the AC power outlet. The player will operate normally.
• Be sure to remove the disc and turn off the player after use.
• Disconnect the AC power cord from the AC outlet when you don’t intend to use the player for long
periods of time.
• Clean the disc by wiping in a straight line from the inside to the outside of the disc.
• The Main plug is used as a disconnect device and shall stay readily operable at any time.
• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
Disc Storage
Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment.
• Do not keep under direct sunlight.
• Keep in a cool ventilated area.
• Store vertically.
• Keep in a clean protection jacket.
Maintenance of Cabinet
For safety reasons, be sure to disconnect the AC power cord from the AC outlet.
• Do not use benzene, thinner, or other solvents for cleaning.
• Wipe the cabinet with a soft cloth.
ENG-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
Accessories
Video/Audio
Cable
AC-IN Cable
A Battery for
Remote Control
(CR2025)
Remote Control
User’s Manual
Install Batteries in the Remote control
1
Open the battery
cover on the bottom
side of the remote
control.
2
Insert a battery
(CR2025).
Make sure that the
polarities (+ and -) are
aligned correctly.
3
Replace the battery
cover.
If the remote control doesn’t operate properly:
- Check the polarity + - of the battery.
- Check if the batteries are drained.
- Check if the remote control sensor is blocked by obstacles.
- Check if there is any fluorescent lighting nearby.
ENG-5
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 1: Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Tour of the Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 2: Connections
Choosing a connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3: Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Using the Search and Skip Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Using the Display Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Using the Disc and Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using the Function Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapter 4: Advanced Functions
Adjusting the Aspect Ratio (EZ View). . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Selecting the Subtitle Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Using the Bookmark Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Using the Zoom Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Clips Menu for MP3/WMA/JPEG/MPEG4/CD Audio . . . . . . . . . . . . . . . 35
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 5: Changing the Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Setting Up the Language Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Setting Up the Audio Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting Up the Display Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Setting Up the Anynet+(HDMI-CEC) (DVD-F1080 only) . . . . . . . . . . . . 55
Chapter 6: Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
ENG-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
SETUP
Note
General Features
- Discs which cannot be played with this
player.
Excellent Sound
• DVD-ROM
• CD-ROM
• CDI
• DVD-RAM
• CDV
• CVD
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound
reproduction.
• Super Audio CD (except CD layer)
• CDGs play audio only, not graphics.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
- Ability to play back may depend on recording
conditions.
Slow Motion
An important scene can be viewed in slow motion.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
1080p Playback (DVD-F1080 only)
This player upconverts regular DVDs for playback on
1080p TVs.
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
COPY PROTECTION
Many DVD discs are encoded with copy
protection. Because of this, you should only connect
your DVD player directly to your TV, not to a VCR.
Connecting to a VCR results in a distorted picture
from copy-protected DVD discs.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional
interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match your
TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
PROGRESSIVE SCAN OUTPUTS
(DVD-FP580(480p))/
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
(DVD-F1080(480p, 720p, 1080p))
“CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IF PROGRESSIVE SCAN PICTURE
PROBLEMS OCCUR, IT IS RECOMMENDED THAT
THE USER SWITCH THE CONNECTION TO THE
‘STANDARD DEFINITION’ (VIDEO) OUTPUT. IF
THERE ARE QUESTIONS REGARDING YOUR TV SET
COMPATIBILITY WITH THIS DVD PLAYER, PLEASE
CONTACT SAMSUNG'S CUSTOMER SERVICE
CENTER.”
MP3/WMA
This unit can play discs created from MP3/WMA files.
MPEG4
This unit can play MPEG4 formats within an avi file.
HDMI (High Definition Multimedia
Interface) (DVD-F1080 only)
HDMI reduces picture noise by allowing a pure
digital video/audio signal path from the player to
your TV.
ENG-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Recording Types
Disc Size
Max. Playing Time
Characteristics
Disc Types (Logos)
-
-
DVD contains excellent sound and
video due to Dolby Digital and
MPEG-2 system.
Single-sided 240 min.
Double-sided 480 min.
DVD
5”
Audio
+
Video
Various screen and audio functions
can be easily selected through the
on-screen menu.
Single-sided 80 min.
Double-sided 160 min.
3 1/2”
AUDIO-CD
74 min.
20 min.
5”
-
CD is recorded as a Digital Signal with
better audio quality, less distortion and
less deterioration of audio quality over
time.
Audio
3 1/2”
Disc Markings
Region Number
~
Play Region Number
Both the DVD player and the discs are
coded by region. These regional
codes must match in order for the disc
to play. If the codes do not match, the
disc will not play.
NTSC broadcast system in U.S.A, Canada, Korea,
Japan, etc.
NTSC
Dolby Digital disc
Stereo disc
STEREO
The Region Number for this player
is described on the bottom panel of
the player.
DIGITAL
SOUND
Digital Audio disc
DTS disc
MP3 disc
DivX Certification
DivX, DivX Certified,
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow
playback and may cause damage to the DVD
player.
and associated logos are
trademarks of DivXNetworks, Inc and
are used under license
ENG-8
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Description
Front Panel Controls
5. SKIP
(
)
/ SEARCH
1. STANDBY/ON
When STANDBY/ON is pressed on, the indicator goes out
and the player is turned on.
2. STANDBY Indicator
When the unit is first plugged in, the indicator lights.
3. DISC TRAY
(
)
Use to reverse skip a scene or music..
6. STOP
Stops disc play.
7. PLAY/PAUSE
(
)
(
)
Begin or pause disc play.
Place the disc here.
4. OPEN/CLOSE
8. SKIP
(
)
/ SEARCH
(
)
Use to forward skip a scene or music.
Press to open and close the disc tray.
Rear Panel (DVD-FP580)
1. DIGITAL AUDIO OUT JACKS
-
3. AUDIO OUT JACKS
-
Use coaxial digital cable to connect to a compatible
Dolby Digital receiver.
Use audio cables to connect to the Audio input jacks of
your television or audio/video receiver
-
Use coaxial digital cable to connect to an A/V Amplifier
that contains a Dolby Digital, MPEG2 or DTS decoder.
4. VIDEO OUT JACK
Use a video cable to connect to the Video input jack on
your television.
-
2. COMPONENT VIDEO OUT JACKS
-
-
-
Use these jacks if you have a TV with Component
5. AC IN JACK
-
R
B
Video in jacks. These jacks provide P , P and Y video.
If P-SCAN is set to “ON” in Video Output of the Setup
Menu, progressive scan mode will work.
Use AC IN cable(Included) to connect this jack into the
power outlet.
If I-SCAN is set to “ON” in Video Output of the Setup
Menu, interlaced scan mode will work.
ENG-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Rear Panel (DVD-F1080)
1. DIGITAL AUDIO OUT JACKS
-
4. VIDEO OUT JACK
-
Use coaxial digital cable to connect to a compatible
Dolby Digital receiver.
Use a video cable to connect to the Video input jack on
your television.
-
Use coaxial digital cable to connect to an A/V Amplifier
that contains a Dolby Digital, MPEG2 or DTS decoder.
5. AC IN JACK
-
Use AC IN cable(Included) to connect this jack into the
power outlet.
2. COMPONENT VIDEO OUT JACKS
-
-
-
Use these jacks if you have a TV with Component
6. HDMI OUT JACK
-
R
B
Video in jacks. These jacks provide P , P and Y video.
If P-SCAN is set to “ON” in Video Output of the Setup
Menu, progressive scan mode will work.
Use an HDMI cable to connect this jack to the HDMI
jack on your television for the best quality picture.
If an HDMI cable is connected to an HDMI-compatible
TV, HDMI will be output automatically from the player
about 10 seconds later.
-
If I-SCAN is set to “ON” in Video Output of the Setup
Menu, interlaced scan mode will work.
3. AUDIO OUT JACKS
Use audio cables to connect to the Audio input jacks of
your television or audio/video receiver.
-
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the
TV’s menu system.
- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion
adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input
(DVD-F1080 only).
- Refer to the TV's instruction manual for detailed information regarding the TV’s HDMI input jack (DVD-
F1080 only).
- See pages 50 ~ 52 to get more information on how to use the setup menu.
ENG-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
Tour of the Remote Control
1. STANDBY/ON Button
Turns the power on or standby.
2. NUMBER Buttons
3. DISC MENU (NUMBER 4) Button
Brings up the Disc menu.
1
2
12
13
3
4
5
14
15
4. ZOOM (NUMBER 7) Button
Enlarge DVD Picture.
5. INFO Button
16
17
Displays the current disc mode.
6
7
8
6. SEARCH Buttons (
)
/
18
Allow you to search forward/backward through a disc.
7. STOP Button (
8. SKIP Buttons (
)
19
9
)
/
10
Use to skip the title, chapter or track.
9. MENU Button
11
20
Brings up the DVD player’s menu.
10. ENTER / ¦ Buttons
/ , /
This button functions as a toggle switch.
11. EXIT Button
Exit the on-screen menu.
12. OPEN/CLOSE ( ) Button
To open and close the disc tray.
13. AUDIO (NUMBER 5) Button
Use this button to access various audio functions on a disc.
14. REPEAT (NUMBER 6) Button
Allows you to repeat play a title, chapter, track or disc.
15. SUBTITLE (NUMBER 9) Button
16. VIDEO SEL. Button
Change Video output mode.
17. EZ VIEW (NUMBER 0) Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3).
18. PLAY/PAUSE Button (
Begin/Pause disc play.
)
19. RETURN Button
Returns to a previous menu.
20. CANCEL Button
Use to remove menus or status displays from the screen.
ENG-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
CONNECTIONS
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV
and other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any
cables.
- Refer to the user’s manual of the additional components (such as a TV) you are connecting for
more information on those particular components.
Connecting to a TV with HDMI Jack (DVD-F1080 only)
1
Using an HDMI-HDMI cable (not included) connect the HDMI
OUT jack on the rear of the DVD player to the HDMI IN jack of
your TV.
2
Press the input selector button on your TV remote control until
the HDMI signal from the DVD player appears on your TV
screen.
HDMI cable
(Not Included)
Connecting to a TV with DVI Jack (DVD-F1080 only)
1
Using an HDMI-DVI cable (not included), connect the HDMI
OUT jack on the rear of the DVD player to the DVI IN jack of
your TV.
2
Using the audio cables, connect the AUDIO (red and white)
OUT jacks on the rear of the DVD player to the AUDIO
(red and white) IN jacks of your TV.
WHITE
RED
RED
Audio Cable
Turn on your DVD player and TV.
HDMI-DVI cable
(Not Included)
WHITE
3
Press the input selector button on your TV remote control until
the DVI signal from the DVD player appears on your TV screen.
ENG-12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
HDMI VIDEO Specifications
- Depending on your TV, certain HDMI output resolutions may not work.
- Please refer to the user's manual of your TV.
- If an HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI automatically about
10 seconds later.
- For better picture quality, set the HDMI output resolution to 720p, 1080i or 1080p .
- This player upconverts regular DVDs for playback on 1080p TVs. It does not play HD DVDs or Blu-Ray discs.
- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player
using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-
CEC).(see page 55-56)
- If your TV has an
logo, then it will
supports the Anynet+ function.
• HDMI (High Definition Multimedia Interface)
HDMI enables you to make a digital video and audio connection with a single cable.
Using HDMI, the DVD player transmits a digital video and audio signal which displays a vivid picture on a
TV having an HDMI input jack.
• HDMI connection description
HDMI connector - Video and audio are transferred digitally without compression (LPCM or Bit Stream
data).
- The player outputs a pure digital signal to the TV through an HDMI cable.
- If your TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on
the screen.
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal. However, when playing a DVD, the signal transmitted to
a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital
converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and
signal loss. HDMI technology is superior because it requires no D/A conversion and is a pure digital signal
from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content output via
HDMI/DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and
a display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized
copies from being made.
ENG-13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Connecting to a TV (Progressive)
1
Using Component video cables (not included), connect the
COMPONENT VIDEO OUT jacks on the rear of the DVD player
to the COMPONENT IN jacks of your TV.
RED
GREEN
BLUE
2
Using the audio cables, connect the AUDIO (red and white)
OUT jacks on the rear of the DVD player to the AUDIO (red
and white) IN jacks of your TV.
Turn on the DVD player and TV.
RED
WHITE
3
Set the Video Output to P-SCAN in the Display Setup menu.
(See pages 50 to 52)
Audio Cable
WHITE
Component cable
(not included)
RED
You can also use the VIDEO SEL. button to change the Video
Output mode. (See page 16)
RED
BLUE
GREEN
4
Press the input selector button on your TV remote control until
the Component signal from the DVD player appears on the TV
screen.
To see the progressive video output,
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method.
Progressive scanning method provides better and clearer picture quality.
ENG-14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Connecting to a TV (Interlace)
- Connecting to your TV using Component video cables.
- This is the best available connection if your TV is not capable of receiving a Progressive Scan
signal.
- You will enjoy excelllent quality and accurate color reproduction images. Component video
B
R
separates the picture element into black and white(Y), blue(P ), red(P ) signals to present clear
and clean images. (Audio signals are delivered through the audio output.)
1
Using Component video cables (not included), connect the
COMPONENT VIDEO OUT jacks on the rear of the DVD player
to the COMPONENT IN jackls of your TV.
2
RED
BLUE
GREEN
Using the audio cables, connect the AUDIO (red and white)
OUT jackls on the rear of the DVD player to the AUDIO (red
and white) IN jackls of your TV.
Turn on your DVD player and TV.
3
RED
WHITE
Set the Video Output to I-SCAN in the Display Setup menu.
(See pages 50 to 52)
Audio Cable
WHITE
You can also use the VIDEO SEL. button to change the Video
Output mode. (See page 16)
Component cable
(not included)
RED
RED
BLUE GREEN
4
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 17 to 18)
R
B
- The component jack of your TV may be marked “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P , P , Y”
depending on the manufacturer. The number and position of the jacks may vary depending on the TV set.
Please refer to the user's manual of your TV.
ENG-15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Connecting to a TV (Video)
1
Using Video/Audio cables, connect the VIDEO (yellow)/AUDIO
(red and white) OUT jacks on the rear of the DVD player to the
VIDEO (yellow)/AUDIO (red and white) IN jacks of your TV.
2
Turn on your DVD player and TV.
RED
RED
WHITE
YELLOW
Audio
Cable
Video Cable
(Included)
WHITE
YELLOW
3
Press the input selector button on your TV remote control until
the Video signal from the DVD player appears on the TV
screen.
Note
- Noise may be generated if the audio cable placed too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 17 to 18)
- The number and position of the jacks may vary depending on your TV set. Please refer to the user's manual
of your TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) jack of the DVD
player.
- If you press the VIDEO SEL. button when the DVD Player is in stop mode or no disc is inserted, the Video
Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN).
ENG-16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Connecting to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and white)
OUT jacks on the rear of the DVD player to the AUDIO (red
and white) IN jacks of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO,
COMPONENT or HDMI OUT jacks on the rear of the DVD
player to the VIDEO, COMPONENT or HDMI-DVI IN jacl of
your TV as described on pages 12 to 16.
3
RED
WHITE
Turn on your DVD player, TV, and Amplifier.
Audio Cable
WHITE
RED
2-Channel stereo amp
4
Press the input select button of the Amplifier to select external
input in order to hear sound from your DVD player..
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier.(See pages 48 to 49)
- The position of jacks may vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
ENG-17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Connecting to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
If using a Coaxial cable (not included), connect the DIGITAL
AUDIO OUT (COAXIAL) jack on the rear of the DVD player to
the DIGITAL AUDIO IN (COAXIAL) jack of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO,
COMPONENT or HDMI OUT jacks on the rear of the DVD
player to the VIDEO, COMPONENT or HDMI-DVI IN jacks of
your TV as described on pages 12 to 16.
Coaxial Cable
(not included)
3
Turn on your DVD player, TV, and Amplifier.
Dolby digital or
DTS amp
4
Press the input select button of the Amplifier to select external
input in order to hear sound from your DVD player.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier you have connected. (See pages 48 to 49)
- The position of jacks may vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
ENG-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
BASIC FUNCTIONS
Playing a Disc
Before Play
- Turn on your TV and set it to the Video Input your DVD player is connected to with your TV’s
remote control.
- If you connected the DVD player to an external Audio System, turn on your Audio System and set
it to the correct Audio Input.
After plugging in the player, the first time you press the DVD POWER button, the screen
to the right appears: If you want to select a language, press a NUMBER button.
(This screen will only appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings may change whenever you
turn the power on or off. Therefore, make sure that you select the language you want to
use.
Once you select a menu language, you can change it by pressing the
button on the
front panel of the unit for more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where you can reset your
preferred language.
Playback
1
Press the OPEN/CLOSE
(
) button.
The STANDBY indicator
light goes out and the tray
opens.
2
Place a disc gently into the
tray with the disc’s label
facing up.
RESUME function
3
When you stop disc play, the player remembers
where you stopped, so when you press the
PLAY/PAUSE ( ) button again, it will pick up
where you left off.
Press the PLAY/PAUSE (
button or OPEN/CLOSE (
button to close the disc tray.
)
)
ENG-19
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
Note
4
- If the player is left in the stop mode for more than
one minute without pressing any buttons, a
screen saver will be activated. Press the
Stopping Play
Press the STOP ( ) button
during play.
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
30 minutes, the power will automatically turn off.
5
Removing the Disc
Press the OPEN/CLOSE
(
) button.
Screen stops, no sound.
To resume, press the PLAY/PAUSE ( ) button
once again.
6
Pausing Play
Press the PLAY/PAUSE
(
) on the remote control
during play.
Note
If the player is left for about 5 minutes in pause
mode, it will stop.
No sound is heard during slow mode.
Press the PLAY/PAUSE ( ) button to resume
normal play.
7
Slow Motion Play
Press the SEARCH (
)
/
button to choose the play
speed between 1/8, 1/4 and
1/2 of normal speed during
PAUSE mode.
Note
- The ( ) icon indicates an invalid button press.
ENG-20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
Using the Search and Skip Functions
During play, you can search quickly through a chapter or track, and use the skip function to jump to
the next selection.
Searching through a Chapter or Track
If you want to search at a faster speed on the
DVD or CD, press and hold the button
During play, press the
SEARCH ( or
) button
DVD 2X, 4X, 64X, 128X
on the remote control for
more than 1 second.
CD
2X, 4X, 8X
Note
- The speed marked in this function may be
different from the actual playback speed.
- No sound is heard during search mode
(Except CD).
Skipping Tracks
During play, press the SKIP
(
or
) button.
- When playing a DVD, if you press the SKIP (
)
button, it moves to the next chapter. If you press
the SKIP ( ) button, it moves to the beginning
of the chapter. One more press makes it move to
the beginning of the previous chapter.
- When playing a CD, if you press the SKIP (
button, it moves to the next track. If you press
)
the SKIP ( ) button, it moves to the beginning
of the track. One more press makes it move to
the beginning of the previous track.
ENG-21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
Using the Display Function
When Playing a DVD/MPEG4
You can select Info in the function menu by
pressing the MENU button.
1
During play, press the
INFO button on the remote
control.
DVD
2
DVD
Press the / buttons to
001
Title
select the desired item.
002
Chapter
00:00:13
Time
ENG 5.1CH
Audio
Off
Subtitle
Enter
MPEG4
001
00:00:13
MP3 1/8
Off
Enter
You may use the number buttons of the remote
control to directly access a title, chapter or to
start the playback from a desired time.
3
Press the ¦/ buttons to
make the desired setup and
then press the ENTER
button.
4
To make the screen
disappear, press the INFO
button again.
ENG-22
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
Note
To access the desired title when there is more than one in the disc.
For example, if there is more than one movie on a DVD, each movie will be identified.
Title
Chapter
Most DVD discs are recorded in chapters so that you can quickly find a specific passage.
Allows playback of the film from a desired time. You must enter the starting time as a reference.
The time search function does not operate on some discs.
Time
Audio
Refers to the film's soundtrack language. In the example, the soundtrack is played in English 5.1CH.
A DVD disc can have up to eight different soundtracks.
Refers to the subtitle languages available in the disc.
Subtitle You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen.
A DVD disc can have up to 32 different subtitles.
Using the Disc and Title Menu
Using the Disc Menu
1
During the playback of a
DVD disc, press the MENU
button on the remote
control.
Note
2
- Depending on a disc, the Disc Menu may not
work.
- You can also select the Disc Menu, using the
DISC MENU button on the remote control.
Press the / buttons to
select Disc Menu, then
press the or ENTER
button.
Press ENTER key
for Disc Menu
Enter
Return
Menu
ENG-23
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
Using the Title Menu
1
During the playback of a
DVD disc, press the MENU
button on the remote
control.
2
Press the / buttons to
select Title Menu, then
press the or ENTER
button.
Press ENTER key
for Title Menu
Note
- Depending on a disc, the Title Menu may not
work.
Enter
Return
Menu
- Title Menu will only be displayed if there are at
least two titles in the disc.
Using the Function Menu
Using the Function Menu (DVD)
1
Press the MENU button
during playback.
2
Info
Press the / buttons to
Zoom
select Function, then press
Bookmark
the or ENTER button.
Repeat
EZ View
- Info (See pages 22 to 23)
- Zoom (See page 34)
Angle
- Bookmark
Enter
Return
Menu
(See pages 32 to 33)
- Repeat (See pages 25)
- EZ View
(See pages 27 to 28)
- Angle (See pages 31)
You can also directly select these functions
using their respective buttons on the remote
control.
3
Press the / buttons to
select one of the six
functions. Then press the
or ENTER button to
access the function.
- INFO
- ZOOM
- EZ VIEW
- REPEAT
ENG-24
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
Repeat Play
Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc.
When playing a DVD
1
Press the REPEAT button
on the remote control.
Repeat screen appears.
A DVD repeats play by chapter or title.
DVD
2
Chapter ( ): repeats the chapter that is
playing.
Press the ¦/ buttons to
select Chapter, Title or A-B,
then press the ENTER
button.
ENTER REPEAT
Off
01
01 A - B
T
Title (
T
): repeats the title that is playing.
A-B: repeats a segment of the disc that you
select.
Using the A-B Repeat function
1. Press the REPEAT button on the remote control.
2. Press the ¦/ button to select A-B button in the on screen display.
3. Press the ENTER button at the point where you want repeat play to start (A).
B is automatically highlighted.
4. Press the ENTER button at the point where you want the repeat play to stop (B).
- To return to normal play, press the CANCEL button.
Note
A-B REPEAT does not allow you to set point (B) until at least 5 seconds of playback time has
elapsed after point (A) has been set.
DVD
3
To return to normal play,
ENTER REPEAT
Off
01
01 A - B
T
press the REPEAT button
again, then press the ¦/
buttons to select Off and
press the ENTER button.
Note
- Depending on a disc, the Repeat function may
not work.
ENG-25
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
Slow Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments
being played etc., so you can study them more closely.
When playing a DVD
1
During play, press the
PLAY/PAUSE ( ) button.
2
Press the SEARCH (
/
)
button to choose the play
speed between 1/8, 1/4 and
1/2 of normal speed during
PAUSE mode.
ENG-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
ADVANCED FUNCTIONS
Adjusting the Aspect Ratio (EZ View)
Changing the aspect ratio (DVD)
Press the EZ VIEW
button.
- The screen size
changes when the
button is pressed
repeatedly.
- The screen zoom mode
operates differently
depending on the screen
setting in the Display
Setup menu.
To make the aspect ratio bar disappear,
press the CANCEL button.
EZ VIEW
WIDE SCREEN
- To ensure correct
operation of the EZ
VIEW button, you should
set the correct aspect
ratio in the Display
Setup menu.
(See pages 50 to 52).
If you are using a 16:9 TV
For 16:9 aspect ratio discs
For 4:3 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off. When
playing a 2.35:1 aspect ratio disc, the black bars at the top
and bottom of the screen will disappear. The picture will
look vertically stretched. (Depending on a type of disc, the
black bars may not disappear completely.)
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
ENG-27
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
If you are using a 4:3 TV
For 16:9 aspect ratio discs
For 4:3 aspect ratio discs
- 4:3 Letter Box
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
Displays the content of the DVD title in 16:9 aspect ratio.
The black bars will appear at the top and bottom of the
screen.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- 4:3 Pan&Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- ZOOM FIT
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears.
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
Note
This function may behave differently depending on the type of disc.
ENG-28
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Selecting the Audio Language
You can select a desired audio language available on a disc quickly and easily with the AUDIO
button.
Using the AUDIO button (DVD/MPEG4)
1
Press the AUDIO button.
The Audio changes when
the button is pressed
repeatedly.
- The audio languages
are represented by
abbreviations.
DVD
AUDIO
ENG DOLBY DIGITAL 5.1CH
Press the AUDIO button
on the remote control
repeatedly to select the
desired Audio (MP3,
PCM, WMA, AC3 and
MPEG) on MPEG4 discs
then press the ENTER
button .
MPEG4
AUDIO
PCM 1/2
2
To remove the AUDIO
icon, press the CANCEL
or RETURN button.
Note
- This function depends on audio languages that
are encoded on the disc. This function may not
work with all DVDs.
- A DVD disc can contain up to 8 audio
languages.
- To have the same audio language come up
whenever you play a DVD; Refer to “Using the
Audio Language” on page 45.
ENG-29
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Selecting the Subtitle Language
You can select a desired subtitle quickly and easily with the SUBTITLE button.
Using the SUBTITLE button (DVD/MPEG4)
1
Press the SUBTITLE
button.
The subtitle changes when
the button is pressed
repeatedly.
The subtitle languages are
represented by
abbreviations.
DVD
SUBTITLE
Off
MPEG4
An External subtitle
option will appear,
depending on the DivX
Disc.
Press the Subtitle button
on the remote control
repeatedly to select the
desired subtitle
MPEG4
SUBTITLE
Off
language on an MPEG4
disc.
2
To remove the SUBTITLE
icon, press the CANCEL
or RETURN button.
Note
- Depending on the DVD, you may have to select
the desired subtitle in the DVD’s Disc Menu.
Press the DISC MENU button.
- This function depends on what subtitles are
encoded on the disc. This function may not work
with all DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD;
Refer to “Using the Subtitle Language” on page
46.
ENG-30
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Changing the Camera Angle
When a DVD contains multiple angles of a particular scene, you can use the ANGLE
function.
Using the ANGLE function (DVD)
If the disc contains multiple angles, the ANGLE mark appears on the screen.
1
During play, press the
MENU button on the
remote control.
2
Info
Press the / buttons to
Zoom
Bookmark
select Function , then
Repeat
press the
button.
or ENTER
EZ View
Angle
Enter
Return
Menu
3
Info
Press the / buttons to
select Angle , then press
the ¤or ENTER button.
Zoom
Bookmark
Repeat
EZ View
Angle
Enter
Return
Menu
4
4/6
Press the ¦/ buttons
on the remote control to
select the desired angle.
Note
- If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not
work.
ENG-31
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Using the Bookmark Function
This feature lets you bookmark sections of a DVD, so you can quickly find them at a later time.
Using the Bookmark Function (DVD)
1
During play, press the
MENU button on the
remote control.
2
Info
Press the / buttons to
Zoom
select Function, then
Bookmark
Repeat
press the
button.
or ENTER
EZ View
Angle
Enter
Return
Menu
3
Info
Press the / buttons to
Zoom
select Bookmark, then
Bookmark
Repeat
EZ View
Angle
press the
button.
or ENTER
Enter
Return
Menu
4
When you reach the
scene you want to mark,
press the ENTER button.
Up to three scenes may
be marked at a time.
CANCEL
Note
- Depending on a disc, the Bookmark function may
not work.
ENG-32
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Recalling a Marked Scene
1~3
The first 1~3 steps are the
same as those for “Using
the Bookmark Function”
on page 32.
CANCEL
4
Press the ¦/ buttons to
select a marked scene.
5
Press the PLAY/PAUSE
(
) button to skip to
the marked scene.
Clearing a Bookmark
1~3
The first 1~3 steps are the
same as those for “Using
the Bookmark Function”
on page 32.
4
CANCEL
Press the ¦/ buttons to
select the bookmark
number you want to delete.
5
Press the CANCEL button
to delete a bookmark
number.
ENG-33
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Using the Zoom Function
Using the Zoom Function (DVD)
1
During play, press the
MENU button on the
remote control.
2
Info
Press the / buttons to
Zoom
select Function, then
Bookmark
Repeat
press the
button.
or ENTER
EZ View
Angle
Enter
Return
Menu
3
Info
Press the / buttons to
Zoom
select Zoom, then press
Bookmark
Repeat
EZ View
Angle
the
or ENTER
button.
Enter
Return
Menu
During DVD play, press ENTER to zoom in the
4
following order. 2X O¤4X O¤2X O¤Normal.
Press the / or ¦/
buttons to select the part of
the screen you want to zoom
in on.
Press the ENTER button.
ENG-34
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Clips Menu for MP3/WMA/JPEG/MPEG4/CD Audio
CD Audio or discs with MP3/WMA/JPEG/MPEG4 contain individual songs and/or pictures that will
be organized into folders on this unit as shown below. They are similar to how you use your
computer to put files into different folders.
Open the disc tray.
Off
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
-
-
-
-
: MP3 file icon.
: WMA file icon.
: JPEG file icon.
-
-
-
: Name of currently playing file.
: Current Playback Time.
: Current Playback Mode : There are four
modes. They can be selected in order by
pressing the REPEAT button.
:
AVI file icon.
- Off: Normal Playback
-
: CD Audio file icon.
: Folder icon.
- Track: Repeats the current track.
- Folder: Repeats the current folder.
- Random: Files in the disc will be played
in random order.
-
-
: Current Folder icon.
Note
• When playing MPEG4 file, the VIDEO SEL. only work in stop mode,
Folder Selection
The folder can be selected in Stop or Play mode.
- To select the Parent Folder
Press the RETURN button to go to the parent folder,
Root
or press the / buttons to select “..” and
press ENTER to go to the parent folder.
WMA
JPEG
- To select the Peer Folder
Press the / buttons to select the desired folder,
MP3
Parent Folder
then press ENTER.
MUSIC
Current Folder
- To select the Sub-Folder
Press the / buttons to select the desired folder,
then press ENTER.
1st
Sub-Folders
2nd
SONG FILE 1
SONG FILE 2
Peer Folders
SONG FILE 3
MPEG4 FILES
ENG-35
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
MP3/WMA/CD Audio Playback
Off
1
Open the disc tray.
Place the disc on the tray.
Close the tray.
2
Press the / or ¦
/
buttons to select a song
file.
Press ENTER to begin
playback of the song file.
P l a y
O f f
00:00:23
B e c a u s e Yo u
T
. . .
B e c a u s e Yo u
C a c t u s
S a d D a y u
Wo n d e r f u l
REPEAT
Enter
Return
Repeat
Repeat/Random playback
1
Press the REPEAT button
to change the playback
mode. There are four
modes; Off, Track, Folder
and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same extension
in the current folder.
- Random: Song files which have the same extension will be
played in random order.
To resume normal play, press the CANCEL button.
ENG-36
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
CD-R MP3/WMA file
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
When you record MP3 or WMA files on a CD-R for
playback in this unit, please refer to the following.
Sound quality with WMA files basically depends on the rate
of compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps.
Conversely, files with decompression rates below 64Kbps
or over 192Kbps will not be played properly.
Sampling rate that can be supported for WMA files is >30
Khz.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following
types: Windows MediaTM (registered trade mark of Microsoft
Inc) and SDMITM (registered trade mark of The SDMI
Foundation). You cannot copy such files.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file
extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters
or less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or
as an assurance of sound quality. You should note that
certain technologies and methods for MP3 file recording on
CD-Rs prevent optimal playback of these files on your DVD
player (degraded sound quality and in some cases, inability
of the player to read the files).
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to
160 Kbps. However, choosing higher rates, like 192
Kbps or more, only rarely give better sound quality.
Conversely, files with decompression rates below 128 Kbps
will not be played properly.
- This unit can play a maximum of 500 files and 500 folders
per disc.
ENG-37
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
MPEG4 Playback
MPEG4 Play Function
.
AVI files are used to contain the audio and video data. Only AVI format files with the “.avi”
extensions can be played.
Off
1
Open the disc tray.
Place the disc on the tray.
Close the tray.
2
Press the / or ¦/
buttons to select an avi file
(DivX/XiviD) and then
press ENTER button.
S t o p
O f f
00:00:00
/ M P E G 4
T
. . .
a 0 1 _ d i v x 5 1 b - 8
a 0 2 _ d i v x 5 0 5 b - 8
a 0 3 _ d i v x 5 0 2 s p - 8
a 0 4 _ d i v x 4 1 2 - 8
Menu
Enter
Return
Repeat Playback
To return to normal play, press the CANCEL
button.
Press the REPEAT button to
change playback mode.
There are 3 modes
Off, Folder, Title.
- Folder : repeats the AVI files which have the same extension
in the current folder.
- Title : repeats the title that is playing.
ENG-38
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Possible warning messages that may appear when trying to
play DivX/AVI files are :
1. No Authorization
MPEG4 Function Description
Function
Description
Reference page
-
During play, press the
button, it moves forward
or backward 5 minutes.
or
Skip
or
- File with bad registration code.
(
(
)
)
During play, press the SEARCH
(
or
) button and press
Search
or
again to search at a faster
speed. Allows you to search
at a faster speed in an AVI
file. (2X, 4X, 8X)
-
Allows you to search at a
slower speed in an AVI file.
(1/8X, 1/4X, 1/2X)
Slow Motion
Play
P 20
P 34
2. Unsupported Codec
Will zoom in
2X/4X/2X/Normal
ZOOM
- Files with certain Codec Types, Versions (ex.
MP4, AFS and other proprietary codecs) are not
supported by this player.
- Depending on the MPEG4 file, these functions may not work.
CD-R AVI file
00:00:00
This unit can play the following video compression formats
within the AVI file format:
. . .
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple Profile)
- DivX 5 contents (MPEG-4 simple profile plus additional
features such as bi-directional frames. Qpel and GMC are
also supported.)
- XviD MPEG-4 compliant Contents.
3. Unsupported Resolution
- Files containing resolutions higher than the player’s
specification are not supported.
DVD-RW & DVD+R
Format that support for DivX file :
- Basic DivX format DivX3.11 / 4.12/ 5.x
- Xvid (MPEG-4 compliant video codec) and DivX Pro
- File format : *.avi, *.div, *.divx.
T
File you attempt to play
has unsupported resolution.
This unit supports all resolutions up to maximum below.
DivX3.11 & DivX4 & XviD
Bitrate may fluctuate:
DivX5
720 x 480 @30fps
Device may skip decoding 720 x 576 @25fps
the high bitrate portions
and begin decoding again
when Bitrate returns to
normal.
: Maximum bitrate : 4Mbps
Note
- The DVD-FP580/DVD-F1080 can support resolutions up to 720 x 480 @30 frames/ 720 x 576 @25 frames.
- This unit supports CD-R/RWs written in MPEG4 in accordance with the “ISO9660 format”.
ENG-39
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
Picture CD Playback
Off
1
Select the desired folder.
(See page 35)
S t o p
Off
2
0 0 : 0 0 : 0 0
1
Press the / buttons to
. . .
select a Picture file in the
clips menu and then press
the ENTER button.
Menu
Enter
Return
3
ENTER RETURN
Note
Press the INFO button to
display the menu.
Press the ¦/ buttons to
select the menu you want
to view, then press the
ENTER button.
- Press the STOP button to return to the clips
menu.
- When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
Rotation
•
•
•
: The pictures change automatically with about a 6
second interval.
:Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
: The pictures change automatically with
about a 12 second interval.
Zoom
: The pictures change automatically with
about a 18 second interval.
: Press the / buttons to select the part of the screen
you want to zoom in on.
Press the ENTER button. Each time the ENTER
button is pressed, the picture is enlarged up
to 2X.
ENTER RETURN
TIMER:
Slide Show
: The unit enters slide show mode.
•
• Before beginning the Slide Show, the picture interval must be
set.
Note
- Depending on the file size, the amount of time between each picture may be different from the set interval
time.
- If you don’t press any button, the slide show will start automatically in about 10 seconds by default.
ENG-40
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FUNCTIONS
MP3-JPEG Playback
You can play a JPEG photo file using music as a background.
1
Press the / buttons to
select an MP3 file in the
clips menu and then
press the ENTER button.
Music will play from the beginning.
2
Press the / buttons to
select a JPEG file in the
clips menu and then
press the ENTER button.
Note
MP3 and JPEG files have to be on the same
3
Press the STOP button
when you want to stop
the playback.
disc.
CD-R JPEG Discs
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
- The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters
(. / = +).
- Only a consecutively written multi-session disc can be played. If there is a blank segment in the multi-session disc, the disc can
be played only up to the blank segment.
- A maximum of 3000 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can be played automatically.
- Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only the first 500 JPEG files can be played.
- If the number of folders in 1 Disc is over 500, only the first JPEG files in 500 folders can be played.
ENG-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
CHANGING THE SETUP MENU
Using the Setup Menu
The Setup menu lets you customize your DVD player by allowing you to select various language
preferences, set up a parental levels, and even adjust the player to the type of television screen you
have.
1
Language Setup
Audio Setup
With the unit in Stop
mode, press the MENU
button on the remote
control.
Display Setup
Parental Setup :
DivX(R)Registration :
Press the / buttons to
select Setup, then press
Enter
Return
Menu
the
or ENTER button.
DVD-FP580 Setup Menu
Language Setup
Audio Setup
Display Setup
Parental Setup :
DivX(R)Registration :
Anynet+ (HDMI-CEC) : On
Enter
Return
Menu
DVD-F1080 Setup Menu
Language Setup : Setup of the Language.
Audio Setup : Setup of the Audio Options.
Display Setup :Setup of the Display Options. Use to select which type of screen you want to
watch and several display options.
❶
❷
❸
❹
Parental Setup : Setup of the Parental Level. Allows users to set the level necessary to prevent
children from viewing unsuitable movies such as those with violence, adult
subject matter, etc.
❺
Divx(R) Registration : Please use the Registration code to register this player with the DivX(R)
Video On Demand format. To learn more go to www.divx.com/vod.
❻ Anynet+(HDMI-CEC) : Setup of the Anynet+(HDMI-CEC) Options (DVD-F1080 only).
2
Press the / buttons to
access the different
features. Press the
or
ENTER button to access
the sub features.
3
To make the setup screen
disappear after setting up,
press the MENU button
again.
Note
Depending on the disc, some Setup menu
selections may not work.
ENG-42
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Setting Up the Language Features
If you set the player menu, disc menu, audio and subtitle language in advance, they will come up
automatically every time you watch a movie.
Using the Player Menu Language
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Setup, then press
the
Parental Setup :
DivX(R)Registration :
or ENTER button.
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Language Setup,
then press the
ENTER button.
Display Setup
or
Parental Setup :
DivX(R)Registration :
Enter
Return
Menu
LANGUAGE SETUP
4
Player Menu
Disc Menu
Audio
:
:
:
:
:
English
English
English
Automatic
Unicode
Press the / buttons to
select Player Menu, then
press the
button.
Subtitle
or ENTER
DivX Subtitle
Enter
Return
Menu
- The language is selected and the screen
returns to the Language Setup menu.
LANGUAGE SETUP
5
P
l
a
y
e
r
M
e
n
u
√ English
Press the / buttons to
select the desired
- To make the setup menu disappear, press the
MENU button.
Disc Menu
Audio
Français
Deutsch
Español
Italiano
language, then press the
Subtitle
Nederlands
DivX Subtitle
or ENTER button.
Return
Menu
Enter
ENG-43
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Using the Disc Menu Language
This function changes the text language only on the disc menu screens.
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Setup, then press
the
Parental Setup :
DivX(R)Registration :
or ENTER button.
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Language Setup,
then press the
ENTER button.
Display Setup
Parental Setup :
DivX(R)Registration :
or
Enter
Return
Menu
LANGUAGE SETUP
4
Player Menu
Disc Menu
Audio
:
:
:
:
:
English
English
English
Automatic
Unicode
Press the / buttons
to select Disc Menu, then
press the
button.
Subtitle
or ENTER
DivX Subtitle
Enter
Return
Menu
- If the selected language is not recorded on
the disc, the original pre-recorded language is
selected.
LANGUAGE SETUP
5
Player Menu
Disc Menu
Audio
Press the / buttons to
select the desired
√ English
Français
Deutsch
Español
Italiano
- The language is selected and the screen
returns to the Language Setup menu.
language, then press the
Subtitle
Nederlands
or ENTER button.
DivX Subtitle
- To make the setup menu disappear, press the
MENU button.
Enter
Return
Menu
ENG-44
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Using the Audio Language
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Setup, then press
the
Parental Setup :
or ENTER button.
DivX(R)Registration :
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Language Setup,
then press the
ENTER button.
Display Setup
or
Parental Setup :
DivX(R)Registration :
Enter
Return
Menu
LANGUAGE SETUP
4
Player Menu
Disc Menu
Audio
:
:
:
:
:
English
English
English
Automatic
Unicode
Press the / buttons to
select Audio, then press
the
Subtitle
or ENTER button.
DivX Subtitle
Enter
Return
Menu
- Select “Original” if you want the default
soundtrack language to be the original
language the disc is recorded in.
LANGUAGE SETUP
5
Player Menu
Disc Menu
Audio
Original
√ English
Français
Deutsch
Español
Italiano
Press the / buttons to
select the desired
- If the selected language is not recorded on
the disc, the original pre-recorded language is
selected.
language, then press the
Subtitle
or ENTER button.
DivX Subtitle
- The language is selected and the screen
returns to the Language Setup menu.
Enter
Return
Menu
- To make the setup menu disappear, press the
MENU button.
ENG-45
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Using the Subtitle Language
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Press the / buttons to
Audio Setup
select Setup, then press
the
Display Setup
or ENTER button.
Parental Setup :
DivX(R)Registration :
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Language Setup,
then press the
ENTER button.
Display Setup
or
Parental Setup :
DivX(R)Registration :
Enter
Return
Menu
LANGUAGE SETUP
4
Player Menu
Disc Menu
Audio
:
:
:
:
:
English
English
English
Automatic
Unicode
Press the / buttons to
select Subtitle, then press
the
Subtitle
or ENTER button.
DivX Subtitle
Enter
Return
Menu
- Select “Automatic” if you want the subtitle
language to be the same as the language
selected as the audio language.
LANGUAGE SETUP
5
Player Menu
Disc Menu
Audio
Press the / buttons to
select the desired
√ Automatic
English
- Some discs may not contain the language you
select ; in that case the disc will use its
original language setting.
Français
Deutsch
Español
Italiano
language, then press the
Subtitle
DivX Subtitle
or ENTER button.
- The language is selected and the screen
returns to the setup menu.
Enter
Return
Menu
- To make the setup menu disappear, press the
MENU button.
ENG-46
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Using the DivX Subtitle Language
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Press the / buttons to
Audio Setup
Display Setup
select Setup, then press
the
Parental Setup :
or ENTER button.
DivX(R)Registration :
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Language Setup,
then press the
ENTER button.
Display Setup
or
Parental Setup :
DivX(R)Registration :
Enter
Return
Menu
LANGUAGE SETUP
4
Player Menu
Disc Menu
Audio
:
:
:
:
:
English
English
English
Automatic
Unicode
Press the / buttons to
select DivX Subtitle, then
press the
button.
Subtitle
or ENTER
DivX Subtitle
Enter
Return
Menu
- The language is selected and the screen
returns to the setup menu.
LANGUAGE SETUP
5
Player Menu
Disc Menu
Audio
:
:
English
English
Press the / buttons to
select the desired
- To make the setup menu disappear, press the
MENU button.
√ Unicode
Western
Turkish
Central
Cyrillic
Greek
Subtitle
language, then press the
DivX Subtitle
or ENTER button.
Enter
Return
Menu
ENG-47
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Setting Up the Audio Options
Audio Options allow you to setup the audio device and sound status settings
depending on the audio system in use.
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Setup, then press
the
Parental Setup :
DivX(R)Registration :
or ENTER button.
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Audio Setup, then
press the
button.
Display Setup
Parental Setup :
DivX(R)Registration :
or ENTER
Enter
Return
Menu
To make the setup menu disappear, press the
MENU button.
AUDIO SETUP
4
Digital Out
:
:
:
:
PCM
PCM
On
Press the / buttons to
MPEG-2 Digital Out
Dynamic Compression
PCM Down Sampling
select the desired item,
then press the
or
On
ENTER button.
Enter
Return
Menu
ENG-48
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
The following describes each option found in the Audio Setup Menu.
❶
Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Outputs Dolby Digital via digital output.
Select Bitstream when connecting to a Dolby Digital Decoder.
❷
MPEG-2 Digital Out
- PCM : Converts to PCM (2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream (5.1CH or 8 CH). Select Bitstream when
using the Digital Audio Output.
❸
❹
Dynamic Compression
- On : To select dynamic compression. This is useful for watching movies late at night, as it
balances the loud and quiet portions of a disc.
- Off : To select the standard range.
PCM Down Sampling
- On : Select this when the Amplifier connected to the player is not 96KHz compatible.
In this case, the 96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the player is 96KHz compatible. In this case,
all signals will be output without any changes.
Note
Even when PCM Down sampling is Off, some discs will only output down-sampled audio through
the digital outputs.
HDMI (DVD-F1080 only)
- If your TV is not compatible with compressed multi-channel formats (Dolby Digital, DTS,
MPEG), you should set Digital Audio to PCM.
- If your TV is not compatible with LPCM sampling rates over 48kHz, you should set PCM
Down sampling to On.
Note
• To make the Setup menu disappear, press the MENU button.
• There is no analog audio output when you play a DTS disc.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
ENG-49
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Setting Up the Display Options
Display options enable you to set various video functions of the player.
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Setup, then press
the
Parental Setup :
DivX(R)Registration :
or ENTER button.
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Display Setup,
then press the
ENTER button.
Display Setup
Parental Setup :
DivX(R)Registration :
or
Enter
Return
Menu
To make the setup menu disappear, press the
MENU button.
DISPLAY SETUP
4
TV Aspect
Still Mode
: Wide
: Auto
Press the / buttons to
select the desired item,
Screen Messages : On
Video Output
Black Level
: P-SCAN
: Off
then press the
or
ENTER button.
Enter
Return
Menu
DVD-FP580 Display Setup
DISPLAY SETUP
TV Aspect
Still Mode
: Wide
: Auto
Screen Messages : On
Video Output
HDMI
: P-SCAN
Picture Quality
Enter
Return
Menu
DVD-F1080 Display Setup
ENG-50
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
TV Aspect
❺
HDMI (DVD-F1080 only)
❶
Depending on a type of television you have,
you may want to adjust the screen setting
(aspect ratio).
This setting is used when the unit is
connected by HDMI to Display devices (TV,
Projector, etc.).
- Resolution Setting
- 4:3 Letter Box : Select when you want to
see the total 16:9 ratio screen DVD
supplies, even though you have a TV with a
4:3 ratio screen. Black bars will appear at
the top and bottom of the screen.
The resolution setting is dependent on the
capability of your TV or Monitor.
- Auto : Auto resolution setting
- Manual : Manual resolution setting
- Resolution
- 4:3 Pan&Scan : Select this for conventional
size TVs when you want to see the central
portion of the 16:9 screen. (Extreme left and
right side of movie picture will be cut off.)
•
•
•
•
480p : 720 x 480
720p : 1280 x 720
1080i : 1920 x 1080
1080p : 1920 x 1080
- 16:9 Wide : You can view the full 16:9
picture on your wide screen TV.
DISPLAY SETUP
For the best video performance, check your
TV’s user manual for proper resolution
setting.
TV Aspect
4:3 Letter Box
4:3 Pan&Scan
√ 16:9 Wide
Still Mode
Screen Messag
Video Output
Black Level
: I-SCAN
: Off
DISPLAY SETUP
TV Aspect
Still Mode
: Wide
: Auto
Enter
Return
Menu
Screen Messages : On
Video Output
HDMI
: P-SCAN
❷ Still Mode
These options will help prevent picture shake
in still mode and display small text clearer.
Picture Quality
Enter
Return
Menu
- Auto : When selecting Auto, Field/Frame
mode will be automatically ajusted.
- Field : Select this feature to minimize
screen shaking.
HDMI SETUP
Resolution Setting : Manual
Resolution : 720p
- Frame : Select this feature when you want
to read text more clearly on the screen .
❸ Screen Messages
Enter
Return
Menu
Use to turn on-screen messages On or Off.
Video Output
Select Video Output.
If your TV does not support the resolution
that have been chosen, the following
warning message may appear and the
resolution will be returned to the previous
setting.
❹
- I-SCAN : Select when you want to use
Video and Component 480i(Interlace) Out.
- P-SCAN : Select when you want to use
Component 480p(Progressive) Out or
HDMI.
• If you press the VIDEO SEL. button with
no disc inserted, the Video output mode is
changed in the following order:
(I-SCAN ➝ P-SCAN)
HDMI SETUP
This resolution is not
supported by the TV.
Enter
Return
Menu
ENG-51
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
❻
Picture Quality
- Black Level (DVD-FP580 and DVD-F1080 :
Adjusts the brightness of the screen.(On or
Off) It does not function in Progressive
mode.
- Brightness : Level 1 ~ Level 5
- Contrast : Level 1 ~ Level 5
- Color Saturation : Level 1 ~ Level 5
DVD-FP580
Black Level Menu
DISPLAY SETUP
TV Aspect
Still Mode
: Wide
: Auto
Screen Messages : On
TV System
: PAL
Video Output
Black Level
: I-SCAN
: Off
Enter
Return
Menu
DVD-F1080
Picture Quality Menu
PICTURE QUALITY
Black Level
Brightness
Contrast
: On
: Level 3
: Level 3
: Level 3
Color Saturation
Enter
Return
Menu
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow
the TV User’s Manual regarding
Progressive Scan settings in the TV’s
menu system.
• If Video Output is set incorrectly, the
screen may be blocked.
• The resolutions available for HDMI output
depend on the connected TV or projector.
For details, see the user’s manual of your
TV or projector (DVD-F1080 only).
• When the resolution is changed during
playback, it may take a few seconds for a
normal image to appear.
• If you have HDMI connected, better
picture quality will be provided when the
output resolution is set to 720p, 1080i
or1080p (DVD-F1080 only).
ENG-52
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Setting Up the Parental Control
The Parental Control function works in conjunction with DVDs that have been assigned a rating,
which helps you control the types of DVDs that your family watches. There are up to 8 rating levels
on a disc.
Setting Up the Rating Level
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Setup, then press
the
Parental Setup :
DivX(R)Registration :
or ENTER button.
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Parental Setup,
then press the
ENTER button.
Display Setup
Parental Setup :
DivX(R)Registration :
or
Enter
Return
Menu
PARENTAL SETUP
: Kids Safe
4
Rating Level
Press the / buttons to
Change Password
select Rating Level, then
press the
button.
or ENTER
Enter
Return
Menu
PARENTAL SETUP
: Kids Safe
5
Rating Level
Enter your password.
By default, password is set
to 0000. Please change
password to other than 0000
to activate parental control
function.
Change Password
Enter Password
Enter
Return
Menu
To make the setup menu disappear, press the
MENU button.
PARENTAL SETUP
6
Rating Level
√ Kids Safe
Press the / buttons to
select the Rating Level
you want, then press the
For example, if you select the Kids Safe level,
discs that contain level 2 or higher will not play.
Change Passwor
Level 2
Level 3
Level 4
Level 5
Level 6
or ENTER button.
e.g) Setting up in Kids
Enter
Return
Menu
Safe.
ENG-53
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Changing the Password
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
select Setup, then press
Display Setup
Parental Setup :
DivX(R)Registration :
the
or ENTER button.
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Parental Setup,
then press the
ENTER button.
Parental Setup :
DivX(R)Registration :
or
Enter
Return
Menu
To make the setup menu disappear, press the
MENU button.
PARENTAL SETUP
: Kids Safe
4
Rating Level
Press the / button to
select Change
Change Password
Password, then press the
or ENTER button.
Enter your new password.
Re-enter the new
Enter
Return
Menu
password again.
PARENTAL SETUP
: Kids Safe
Rating Level
Change Password
Enter Password
Enter
Return
Menu
PARENTAL SETUP
: Kids Safe
Rating Level
Change Password
Enter New Password
Note
Enter
Return
Menu
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
ENG-54
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
Setting Up the Anynet+(HDMI-CEC) (DVD-F1080 only)
Anynet+ is a function that can be used to operate this DVD Player using a Samsung TV
remote control. This is done by connecting the DVD player to a SAMSUNG TV using an HDMI
Cable. (see page 12-13) This is only available with SAMSUNG TVs that support Anynet+.
To operate Anynet+, you must turn Anynet+(HDMI-CEC) On in the Setup Menu.
1
With the unit in Stop
mode, press the MENU
button.
2
Language Setup
Audio Setup
Press the / buttons to
Display Setup
select Setup, then press
the
Parental Setup :
DivX(R)Registration :
Anynet+ (HDMI-CEC) : On
or ENTER button.
Enter
Return
Menu
3
Language Setup
Audio Setup
Press the / buttons to
select Anynet+(HDMI-
CEC), then press the
or ENTER button.
Display Setup
Parental Setup :
DivX(R)Registration :
Anynet+ (HDMI-CEC) : On
Enter
Return
Menu
To make the setup menu disappear, press the
MENU button.
4
Language Setup
Audio Setup
Set the Anynet+(HDMI-
Display Setup
CEC) to “On”on your DVD
Player., then press the
or ENTER button.
Parental Setup :
DivX(R)Registration :
Off
Anynet+ (HDMI-
√
On
Enter
Return
Menu
5
DVDP
View TV
®
®
®
®
Set the Anynet+ function on
your Samsung TV. (See your
TV instruction manual for
more information.).
Select Device
Record
Menu on Device
Device Operation
®
®
®
Receiver
Setup
:
Off
ENTER
Move
Exit
• When you press Anynet+
button on the TV remote
control, the OSD to the right
will appear.
TV Menu
ENG-55
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE SETUP MENU
You can operate the DVD Player by using the TV remote control. These are buttons that can
be used to operate the DVD Player:
,
,
,
,
,
,
and
buttons,
buttons.
- Select Device : Use this option to select device which you want to connect to your TV.
- Menu on Device : Same as MENU button on the DVD Player remote control.
- Device Operation : Same as INFO button on the DVD Player remote control.
Note
• While watching TV, your TV screen will change to the play screen when you press the
PLAY button of the DVD player.
• If you play a DVD when the TV power is off, the TV will power On.
• If you turn the TV off, the DVD Player will power off automatically.
• If you change from HDMI to other sources (Composite,Component,... etc) while playing a
DVD disc, the DVD Player will stop playing.
ENG-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6
REFERENCE
2. Press the ¦/ buttons to select Total, then press the
ENTER button.
Firmware upgrade
Introduction
Samsung will often support the software upgrade
to improve the performance of this unit to the latest
status, through Samsung Internet Site
(www.samsung.com/ca).
Because the specially new mpeg4 codec
continues and it is appearing. What improvements
are made depends on the upgrade software you
are using as well as the software that your DVD-
player contained before the upgrade.
Firmware upgrade starts
-
-
In the middle of the writing, the tray will open
automatically. After taking out the disc, please wait for
about 2 minutes.
How to make an upgrade disc
If the unit was succesfully updated, the unit will turn off
and on after closing the tray automatically. When the
unit turns on, this screen will display.
Write the downloaded file onto a blank CD-R or
CD-RW disc, using the following settings:
3. Press the number buttons to select the desired language.
1. You have to download a new file through Download
Center of Samsung Internet Site
(www.samsung.com/ca).
2. Write the file to Disc using CD-RW of your computer.
Note
- File System CD-ROM ISO Level
- Character set ISO 9660
- Finalized, single session
- Write speed low
Note
- If the “Select Menu Language” doesn’t appear,
please contact to “Samsung Service Center”.
- Do not press any button and unplug the power
code during upgrade.
- The upgrade procedure may change, refer to
the web site (www.samsung.com/ca).
Upgrade procedure
1. Open the disc tray. Place the disc on the tray. Close the
tray. The Firmware upgrade screen appears.
Firmware upgrade
appears on the display
ENG-57
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE
Troubleshooting
Before requesting service, please check the following.
Action
Problem
Page
• Check the batteries in the remote control.
No operations can be
performed with the
remote control.
They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to
drain the microprocessor inside the remote control to reset it. Reinstall
batteries and try to operate the remote control again.
P5
P8
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
• 5.1 channel sound is reproduced only when the following conditions are met :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
5.1 channel sound is
not being reproduced.
P18
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
P48~49
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
The
icon appears
on screen.
Disc Menu doesn’t appear.
• Check if the disc has a Menu.
Play mode differs from
the Setup Menu
selection.
• Some of the functions selected in the Setup Menu may not work properly if the
disc is not encoded with the corresponding function.
P42~56
The screen ratio
• The Screen Ratio is fixed on your DVDs.
P50~52
P48~49
cannot be changed.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
No audio.
The screen is blocked
• Press the
button (on the front panel) for more than 5 seconds with no disc
P19
P53
inside. All settings will revert to the factory settings.
• Press the
button (on the panel) for more than 5 seconds with no disc
Forgot password
inside. All settings including the password will revert to the factory settings.
Don't use this unless absolutely necessary.
If you experience other
problems.
• Go to the contents and find the section of the instruction book that contains
the explanations regarding the current problem, and follow the procedure once
again.
• If the problem still cannot be solved, please contact your nearest Samsung
authorized service center.
• Make sure that the disc is not dirty or scratched.
The picture is noisy or
distorted
P4
Clean the disc.
•
ENG-58
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE
Action
Problem
Page
P12~13
P12~13
No HDMI output
(DVD-F1080 only).
• Check the if the Video output is set to HDMI.
• Check the connection between the TV and the HDMI jack of DVD player.
• See if the TV supports this 480p/720p/1080i/1080p DVD player.
• If snow noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
Abnormal HDMI output
screen (DVD-F1080
only).
• Check if your TV is setup correctly.
HDMI output Jitter
(DVD-F1080 only)..
P50~52
• Screen Jitter may occur when frame rate is converted from 50Hz to 60Hz for
720P/1080i/1080p HDMI (High Definition Multimedia Interface) Output.
• Please refer to the user’s manual of your TV.
ENG-59
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCE
Specifications
Power Requirements
Power Consumption
Weight
AC 120V ~ 60 Hz
7 W
0.976 Kg
General
Dimensions
240mm (W) X 240mm (D) X 50.5mm (H)
+41°F to +95°F
Operating Temperature Range
Operating Humidity Range
10 % to 75 %
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
DVD
(DIGITAL VERSATILE DISC)
CD : 5”
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Disc
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
CD : 3 1/2”
(COMPACT DISC)
1 channel : 1.0 Vp-p (75 Ω load)
Composite Video
Component Video
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Video
Output
HDMI
480p, 720p, 1080i,1080p (DVD-F1080 only)
2 Channel
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*Frequency Response
Audio
*S/N Ratio
110 dB
100 dB
0.004 %
Output
*Dynamic Range
*Total Harmonic Distortion
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications with
out notice.
- Weight and dimensions are approximate.
ENG-60
Download from Www.Somanuals.com. All Manuals Search And Download.
ENG-61
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY TO ORIGINAL PURCHASER
Samsung Electronics Canada Inc.(SECA), warrants that this product is free from defective material and workmanship.
SECA further warrants that if this product falls to operate properly within the specified warranty period and the failure
is due to improper workmanship or defective materials, SECA will repair or replace the product at its option.
All warranty repairs must be performed by a SECA Authorized Service Center. (The name and address of the location
nearest you can be obtained by calling toll free: 1- 800- SAMSUNG)
LABOR
PARTS
One year (Carry- in)
One year
On carry-in models, transportation to and from the service center is the customer’s responsibility.
The original dated sales receipt must be retained by the customer and is the only acceptable proof of purchase. It must
be presented to the authorized service center at the time service is requested.
EXCLUSIONS (WHAT IS NOT COVERED)
This warranty does not cover damage due to accident, fire, flood and/ or other acts of God; misuse, incorrect line volt-
age, improper installation, improper or unauthorized repairs, commercial use or damage that occurs in shipping.
Exterior and interior finish, lamps, glass are not covered under this warranty. Customer adjustments which are
explained in the instruction manual are not covered under the terms of this warranty. This warranty will automatically
be voided for any unit found with a missing or altered serial number. This warranty is valid only on products purchased
and used in Canada.
Samsung Electronics Canada Inc., Customer Service
55 Standish Court Mississauga, Ontario L5R 4B2
Canada
1-800-SAMSUNG (7267864)
www.samsung.com/ca
ENG-62
Download from Www.Somanuals.com. All Manuals Search And Download.
A K 6 8 - 0 1 5 0 3 G ( 0 1 )
C A
. s a m s w u w n w g . c o m / c a
D V D - F 1 0 8 0 / F 1 0 8 0 W
D V D - F P 5 8 0 / F P 5 8 0 W
L e c t e u r D V D
Download from Www.Somanuals.com. All Manuals Search And Download.
Consignes de sécurité importantes
Lisez attentivement ces instructions avant d’utiliser l’appareil. Suivez toutes les instructions relatives à la
sécurité indiquées ci-dessous. Conservez ces instructions à portée de main afin de pouvoir vous y référer
ultérieurement.
1) Lisez ces instructions.
2) Conservez ces instructions.
3) Tenez compte de tous les avertissements.
4) Suivez toutes les instructions.
5) N’utilisez pas cet appareil à proximité d’eau..
6) Nettoyez avec un chiffon sec exclusivement.
7) N’obstruez pas les orifices de ventilation et installez l’appareil conformément aux instructions du fabricant.
8) N’installez pas l’appareil à proximité d’une source de chaleur telle qu’un radiateur, un registre de chaleur,
un réchaud ou tout autre appareil (amplificateurs compris) produisant de la chaleur.
9) Ne désactivez pas les dispositifs de sécurité des fiches électriques polarisées ou reliées à la terre. Une
prise polarisée comporte deux lames, l’une étant plus large que l’autre. Une prise reliée à la terre
comporte deux lames ainsi qu’une broche de mise à la terre. La lame large et la troisième broche sont
destinées à assurer votre sécurité : si la fiche fournie ne s’adapte pas à votre prise murale, consultez un
électricien afin de faire remplacer la prise obsolète..
10) Protégez le cordon d’alimentation : il ne doit pas être piétiné ou pincé, notamment au
niveau des fiches électriques, des prises de courant et de l’endroit d’où il sort de
l’appareil.
11) N’utilisez que des accessoires agréés par le fabricant.
12) N’utilisez que le chariot, le support, le trépied, le dispositif de fixation ou la table
spécifiée par le fabricant ou vendu avec l’appareil. En cas d’utilisation d’un chariot,
soyez prudent lorsque vous déplacez l’ensemble chariot/appareil afin d’éviter qu’il ne
blesse quelqu’un en tombant..
13) Débranchez cet appareil en cas d’orage ou lorsqu’il reste inutilisé pendant une longue période de temps.
14) Confiez la réparation de votre appareil à du personnel qualifié. Une réparation est nécessaire lorsque
l’appareil a été endommagé de quelque manière que ce soit : cordon d’alimentation ou fiche électrique
abîmés, liquide qui a été renversé ou objets qui sont tombés dans l’appareil, exposition de l’appareil à la
pluie ou à l’humidité, dysfonctionnement de l’appareil ou chute de l’appareil.
FRA-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Précautions
Ce symbole indique qu’une tension
Ce symbole indique que les
documents accompagnant cet
appareil contiennent des consignes
d’exploitation et d’entretien
importantes.
dangereuse constituant un risque
d’electrocuti on est présente dans
cet appareil.
ATTENTION :
• Afin de réduire les risques de feu ou d’electrocution, n’exposez pas l’appareil à la pluie ou à l’humidité.
• Utilisez un adaptateur approprié si l’alimentation est du type 240V CA.
PRÉCAUTIONS :
• Afin d’éviter tout risque de choc électrique, veillez à ce que la lame la plus large de la prise électrique soit
entièrement insérée dans la prise murale.
• Afin Pour éviter les chocs électriques, introduíre la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu au fond.
Ce produit est conforme à la réglementation FCC quant aux câbles à paires torsadées blindées et aux
connecteurs blindés utilisés pour raccorder l’appareil à d’autres équipements. Afin de prévenir toute
interférence électromagnétique avec d’autres appareils électriques, tels que radios et télévisions,
utilisez des câbles à paires torsadées blindées et des connecteurs blindés pour effectuer les branchements.
ATTENTION : Le règlement de la FCC stipule que toute modification de cet appareil risque d’annuler
le droit de l’utilisateur de l’utiliser.
Pour prévenir une interférence électromagnétique avec des appareils électriques, tels que poste de radio ou
téléviseur, utilisez les câbles et connecteurs prévus pour la connexion.
La prise d’alimentation fait office de système de déconnexion ; elle do it donc rester disponible en
permanence.
CLASS 1
LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1
LASER APPARAT
PRODUCTO LÁSER CLASE 1
FRA-3
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTENTION
CE PRODUIT UTILISE UN FAISCEAU LASER. EN OPÉRANT UN CONTRÔLE, UN AJUSTEMENT,
OU TOUTE PROCÉDURE AUTRE QUE CELLES INDIQUÉES DANS CE MANUEL, VOUS VOUS
EXPOSEZ À DES RADIATIONS DANGEREUSES. NE JAMAIS OUVRIR LE CAPOT ET NE PAS
ESSAYER DE RÉPARER LE LECTEUR VOUS-MÊME. TOUTE RÉPARATION DOIT ETRE
EFFECTUÉE PAR UN TECHNICIEN QUALIFIÉ.
Remarque:
• Cet appareil ne fonctionne qu’avec une alimentation électrique en 120 V c.a., 60 Hz. Il n’est pas
opérationnel dans d’autres conditions.
• Ce lecteur DVD est conçu et fabriqué pour répondre au Region Management Information. Si le code
régional du disque DVD ne correspond pas à celui du lecteur DVD, l’appareil ne peut pas lire le
disque.
• Le produit accompagnant ce manuel de l’utilisateur est placé sous licence concernant certains droits
de propriété intellectuelle détenus par des tiers. Ce produit est notamment sous licence et est
protégé par les brevets américains suivants :
5,060,220 5,457,669 5,561,649 5,705,762 5,987,417 6,043,912 6,222,983 6,272,096 6,377,524
6,377,531 6,385,587 6,389,570 6,408,408 6,466,532 6,473,736 6,477,501 6,480,829 6,556,520
6,556,521 6,556,522 6,578,163 6,594,208 6,631,110 6,658,588 6,674,697 6,674,957 6,687,455
6,697,307 6,707,985 6,721,243 6,721,493 6,728,474 6,741,535 6,744,713 6,744,972 6,765,853
6,765,853 6,771,890 6,771,891 6 775,465 6,778,755 6,788,629 6,788,630 6,795,637 6,810,201
6,862,256 6,868,054 6,894,963 6,937,552.
Cette licence est limitée à une utilisation privée et non commerciale par le consommateur de l’objet
de la licence. Aucun droit n’est accordé pour une utilisation commerciale. La licence ne couvre aucun
autre produit que celui-ci et elle ne s’étend pas aux produits et aux processus non couverts par une
licence conformément aux normes ISO/IEC 11172-3 ou ISO/IEC 13818-3 utilisés ou vendus en
complément de ce produit. La licence ne couvre que l’utilisation de ce produit pour encoder et/ou
décoder des fichiers audio conformément aux normes ISO/IEC 11172-3 ou ISO/IEC 13818-3. Aucun
droit n’est accordé par cette licence concernant des fonctions ou des caractéristiques du produit non
conformes aux normes ISO/IEC 11172-3 ou ISO/IEC 13818-3.
Attention
• Avant de connecter d’autres éléments au lecteur, assurez-vous que tout est débranché.
• Ne déplacez pas le lecteur pendant qu’il est en marche. Sinon le disque risque d’être rayé ou brisé et les
parties intérieures du lecteur risquent également d’être endommagées.
• Ne placez jamais un vase rempli d’eau ou des objets en métal, sur le lecteur quelle que soit leur taille.
• Ne touchez pas le plateau du disque avec les mains.
• Toutes les influences extérieures telles que les lumières et l’électricité statique peuvent provoquer un
mauvais fonctionnement du lecteur. Si c’est le cas, éteignez le lecteur et remettez-le en marche en
appuyant sur la touche POWER. Ou bien débranchez, puis rebranchez le câble d’alimentation de la prise
secteur. Le lecteur fonctionnera ainsi normalement.
• Enlevez le disque et débranchez le lecteur après usage.
• Déconnectez le câble secteur si vous ne l’utilisez pas pendant une longue période.
• Nettoyez le disque en l’essuyant en ligne droite du centre vers l’extérieur.
• La prise d’alimentation fait office de système de déconnexion ; elle doit donc rester disponible en
permanence.
• La fiche d’alimentation principale est utilisée comme sectionneur de courant et doit demeurer accessible en
tout temps.
• L’appareil ne droit pas être exposé aux gauttes ou aux éclaboussures et aucun objet contenant du liquide,
comme un vase, ne doit être posé sur l’appareil.
Rangement des disques
Faites attention à ne pas endommager les disques car les données qu’ils renferment sont très vulnérables aux
conditions extérieures.
• N’exposez pas directement les disques au soleil.
• Gardez-les dans un endroit bien aéré.
• Rangez-les verticalement.
• Rangez-les dans un étui propre.
Entretien du lecteur
Pour des raisons de sécurité, assurez-vous que le câble d’alimentation est bien débranché de la prise secteur.
• Ne vous servez pas de benzène, de diluants ou d’autres solvants pour le nettoyage.
• Essuyez le lecteur avec un chiffon doux.
FRA-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Avant de commencer
Accessoires
Câble de
connexion
Vidéo/Audio
(Cinch)
Piles pour la
Mode d’emploi
Câble AC-IN
Télécommande
télécommande
(CR2025)
Installation des piles dans la télécommande
1
Retirez le couvercle
du compartiment
des piles situé au
bas de la
télécommande.
2
Insérez la pile
(CR2025).
Assurez-vous qu’elles
sont bien placées en
accord avec la polarité
indiquée.
3
Refermez le
couvercle du
compartiment.
Si la télécommande ne fonctionne pas:
- Vérifiez la polarité des piles.
- Vérifiez l’état d’usure des piles.
- Vérifiez que le capteur de la télécommande n’est pas obstrué.
- Vérifiez l’absence de lumière fluorescente à proximité.
FRA-5
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE DES MATIÈRES
Consignes de sécurité importantes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Précautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Avant de commencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapitre 1: Installation
Caractéristiques des disques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Types et caractéristiques des disques . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Télécommande . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapitre 2: Branchements
Choix de la connexion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapitre 3: Fonctions Elemetaires
Lecture des disques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Recherche et saut de pchapitre ou de plage . . . . . . . . . . . . . . . . . . . . 21
Utilisation de la fonction d’affichage . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Utilisation du menu Disque et pdu menu Titres . . . . . . . . . . . . . . . . . . 23
Utilisation du menu des fonctionnalités . . . . . . . . . . . . . . . . . . . . . . . . 24
Lecture répétée . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Lecture lente.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Chapitre 4: Fonctions Avancees
Réglage du rapport d’aspect hauteur-largeur de l’écran (EZ View) . . . 27
Sélection de la langue d’écoute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Sélection de la langue des sous-titres. . . . . . . . . . . . . . . . . . . . . . . . . . 30
Sélection de l’angle de prise de vue à l’écran. . . . . . . . . . . . . . . . . . . . 31
Utilisation des repères. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Utilisation des fonctions avancées . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Menu Clips pour MP3/WMA/JPEG/MPEG4/CD Audio . . . . . . . . . . . . . 35
Modifier un Dossier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Lecture de MP3/WMA/CD Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Lecture de MPEG4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Lecture de CD images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapitre 5: Changement du Menu Configuration
Utilisation du menu de configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Configuration des options de langue. . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Configuration des options audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Configuration des options d’affichage . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Configuration du contrôle parental . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Réglage de l'option Anynet+ (HDMI CEC) (DVD-F1080 uniquement) . 55
Chapitre 6: Fiche Technique
Mise à jour du micrologiciel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Problèmes et solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
FRA-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapitre 1
INSTALLATION
Remarque
Caractéristiques des disques
- Disques ne pouvant être lus par ce lecteur.
• DVD-ROM
• CD-ROM
• CDI
• DVD-RAM
• CDV
• CVD
Excellente qualité sonore
Le système Dolby Digital mis au point par Dolby
Laboratories, vous garantit une reproduction sonore de
haute qualité.
• Super Audio CD (sauf couche CD)
• Disques CDG: uniquement lecture audio,
Format écran
Vous permettant de choisir entre le format écran normal
(4/3) ou bien le format grand écran (16/9).
sans les graphiques.
- La capacité de lecture dépend des
conditions d'enregistrement.
• DVD-R, +R
Ralenti variable
Vous pouvez visionner une séquence importante en faisant
varier la vitesse du ralenti.
• CD-RW
• DVD+RW, -RW (mode V)
Lecture 1080p
Ce lecteur adapte les DVD standard à la lecture sur des
téléviseurs 1080p (DVD-F1080 uniquement).
- Il se peut que l’unité ne lise pas certains
CD-R, CD-RW et DVD-R en raison du type
de disque ou des conditions
d’enregistrement.
Contrôle parental (DVD)
Le contrôle parental permet aux utilisateurs de fixer le seuil
au-delà duquel ils interdisent à leurs enfants de regarder
des films de violence ou réservés aux adultes.
PROTECTION CONTRE LA COPIE
Nombreux sont les disques DVD protéges contre la
copie. Ainsi vous ne pouvez connecter votre lecteur
DVD que directement à la télévision et non au
magnétoscope. Si vous le connectez à un
magnétoscope, vous n’obtiendrez que des images
déformées par le système de protection
MACROVISION.
Fonctions variées du menu affiché
Vous pouvez sélectionner la langue d’écoute et des sous-
titres, ainsi que l’angle de vue que vous préférez pendant la
lecture.
Balayage progressif
Ce lecteur DVD intègre des technologies destinées à
respecter la propriété intellectuelle dont les droits
sont protégés par des brevets américains et des
procédés de contrôle de la propriété de Macrovision
Corporation et d’autres compagnies. L’utilisation de
cette technologie doit être autorisée par Macrovision
Corporation. Elle est limitée à l’usage domestique ou
aux utilisations strictement définies par Macrovision
Corporation. Les modifications techniques ou le
démontage sont interdits.
Le balayage progressif améliore l’image en doublant le
nombre de lignes de balayage associé à l’affichage
classique par balayage entrelacé.
EZ VIEW (Visionnement facile) (DVD)
La fonction Easy View permet de régler l’image en fonction
du format de votre écran de télévision (16/9 ou 4/3).
Digital Photo Viewer (JPEG)
(visionneur de photos numériques)
Grâce à ce visionneur, vous pouvez voir des images
numériques sur votre téléviseur.
PROGRESSIVE SCAN OUTPUTS
(DVD-FP580(480p))/
(DVD-F1080(480p, 720p, 1080p))
Répétition
Vous pouvez écouter une chanson ou visionner un film
plusieurs fois par une simple pression sur la touche REPEAT.
“LES CONSOMMATEURS DOIVENT NOTER QUE
TOUS LES TÉLÉVISEURS À HAUTE DÉFINITION NE
SONT PAS TOTALEMENT COMPATIBLES AVEC CET
APPAREIL ET QU’UNE ERREUR PEUT SURVENIR
SUR L’IMAGE AU MOMENT DU BALAYAGE
PROGRESSIF DES APPAREILS 525. IL EST
RECOMMANDÉ À L’UTILISATEUR DE BASCULER LA
CONNEXION VERS LA SORTIE ‘DÉFINITION
STANDARD’. SI VOUS AVEZ DES QUESTIONS
CONCERNANT LA COMPATIBILITÉ DES MODÈLES
525P DE NOTRE LECTEUR DVD, VEUILLEZ
CONTACTER NOTRE CENTRE DE SAMSUNG
SERVICE CONSOMMATEURS.”
MP3/WMA
Cet appareil peut lire des disques gravés à partir de fichiers
MP3/WMA.
MPEG4
Cet appareil peut lire les fichiers avi enregistrés au
format MPEG-4.
HDMI (High Definition Multimedia
Interface)
HDMI diminue le bruit d’image en permettant un
cheminement pur du signal vidéo/audio numérique
entre le lecteur et votre TV (DVD-F1080 uniquement).
FRA-7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Types et caractéristiques des disques
Ce lecteur DVD peut lire les disques de types suivants qui sont identifiables par leur logo.
Type d’enregistrement Taille des disques Durée maximale de lecture
Caractéristiques
Type de disque
-
-
Grâce aux systèmes Dolby Digital,
MPEG-2 et DTS, le DVD offre une
excellente qualité audio et vidéo.
Face unique 240 min.
5"
DVD
Double face 480 min.
Audio
+
Vidéo
Les fonctions vidéo et audio peuvent
être facilement sélectionnées sur le
menu à l’écran.
Face unique 80 min.
Double face 160 min.
31/2"
AUDIO-CD
-
Les disques compacts étant
74 min.
20 min.
5"
enregistrés avec un signal numérique,
la qualité sonore est irréprochable,
avec moins de distorsion et sans
risque d’usure ou de détérioration.
Audio
31/2"
Code régional de lecture
Notations sur le disque
~
Code régional de lecture
Le lecteur DVD et les disques sont
codés différemment selon les parties
du monde. Il faut donc le code
correspondant à chaque région pour
un bon fonctionnement du lecteur. Si
vous tentez de lire un disque DVD
avec un code incorrect, le lecteur ne
fonctionnera pas et un message
d’erreur apparaîtra.
Système de diffusion NTSC adopté aux Etats-Unis,
au Canada, en Corée, au Japon, etc.
NTSC
Disque Dolby numérique
Disque stéréo
STEREO
DIGITAL
SOUND
Disque audio numérique
Disque DTS
Le numéro de région du lecteur est
inscrit sur le panneau de dessous du
lecteur.
Disque encodé en MP3
DivX Certification
N’insérez qu’un DVD à la fois. Si vous en
insérez plusieurs, ils ne pourront être lus et
risqueront d’endommager le lecteur.
DivX, DivX Certified et les
logos qui leur sont associés
sont des marques déposées
de DivX Networks, Inc. et font
l’objet d’une licence
FRA-8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Description
Face avant
5. SKIP
(
)
/ SEARCH
1. STANDBY/ON
(
)
Permet une recherche arrière. Utilisez pour sauter un titre,
chapitre ou piste.
Le voyant s’éteint et le lecteur se met en marche lorsque
vous appuyez sur le bouton STANDBY/ON.
2. Voyant STANDBY
6. Touche STOP
(
)
Le voyant s’allume lorsque l’appareil est branché pour la
première fois sur une prise de courant.
3. Tiroir à disque
Pour arrêter la lecture du disque.
7. Touche PLAY/PAUSE
(
)
Pour démarrer ou arrêter temporairement la lecture du
disque.
Permet de charger un disque.
4. Touche OPEN/CLOSE
(
)
8. Touche SKIP
(
)
/ SEARCH
Pour ouvrir ou fermer le tiroir à disque.
Permet une recherche avant. Utilisez pour sauter un titre,
chapitre ou piste.
Face arrière (DVD-FP580)
1. SORTIE DIGITAL AUDIO OUT
-
3. SORTIE ANALOG AUDIO OUT
Branchez aux prises femelles audio de votre téléviseur,
écepteur audio/vidéo.
Utilisez un coaxial numérique pour le raccordement à
un amplificateur Dolby Digital compatible.
-
-
Munissez-vous d’un câble numérique coaxial pour
effectuer le raccordement à un amplificateur A/V équipé
d’un décodeur Dolby Digital, MPEG2 ou DTS.
4. SORTIE VIDEO OUT (signal vidéo)
-
Connectez le lecteur à l’entrée vidéo de votre téléviseur
à l’aide d’un cordon coaxial.
2. SORTIE COMPONENT VIDEO OUT
5. PRISE AC IN (Entrée CA)
Utilisez le câble d'entrée CA (compris) pour brancher
cette prise dans la prise murale.
-
-
-
Utilisez ces prises si vous possédez un téléviseur avec
prises. Élément vidéo Pr, Pb et Y.
Si P-SCAN est sélectionné dans le menu
Configuration, le mode P-SCAN fonctionnera.
Si I-SCAN est sélectionné dans le menu
Configuration, le mode I-SCAN fonctionnera.
-
FRA-9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Face arrière (DVD-F1080)
1. SORTIE DIGITAL AUDIO OUT
-
4. SORTIE VIDEO OUT (signal vidéo)
-
Utilisez un coaxial numérique pour le raccordement à
un amplificateur Dolby Digital compatible.
Connectez le lecteur à l’entrée vidéo de votre téléviseur
à l’aide d’un cordon coaxial.
-
Munissez-vous d’un câble numérique coaxial pour
effectuer le raccordement à un amplificateur A/V équipé
d’un décodeur Dolby Digital, MPEG2 ou DTS.
5. PRISE AC IN (Entrée CA)
-
Utilisez le câble d'entrée CA (compris) pour brancher
cette prise dans la prise murale.
2. SORTIE COMPONENT VIDEO OUT
6. PRISE DE SORTIE HDMI
-
-
-
Utilisez ces prises si vous possédez un téléviseur avec
prises. Élément vidéo Pr, Pb et Y.
Si P-SCAN est sélectionné dans le menu
Configuration, le mode P-SCAN fonctionnera.
Si I-SCAN est sélectionné dans le menu
Configuration, le mode I-SCAN fonctionnera.
-
Utilisez le câble HDMI ou HDMI-DVI pour relier cette
prise à la prise HDMI ou DVI de votre téléviseur pour
augmenter la qualité de l’image.
-
Si le câble HDMI est branché sur un téléviseur doté
d’une sortie HDMI, le mode HDMI s’active
automatiquement au bout de 10 secondes.
3. SORTIE ANALOG AUDIO OUT
Branchez aux prises femelles audio de votre téléviseur,
écepteur audio/vidéo.
-
Remarque
-
Référez-vous au manuel de l'utilisateur de votre récepteur pour savoir si votre TV prend en charge le balayage
progressif(P-SCAN). Si le mode Balayage progressif est pris en charge, suivez les instructions du manuel
d’utilisation du téléviseur relatives aux réglages du balayage progressif dans les menus du téléviseur.
- La sortie Sortie Progressive OUI de cet appareil ne peut être connectée au jack DVI d’une TV ou d’un autre
dispositif en utilisant un adaptateur de conversion. Pour cela, il est nécessaire d’utiliser une TV ou un
dispositif d’affichage ayant une entrée compatible HDCP (DVD-F1080 uniquement).
- Pour plus de détails sur la prise HDMI, reportez-vous au manuel d’instructions du téléviseur (DVD-F1080
uniquement).
- Voir page 50 ~ 52 pour obtenir plus d’informations à propos de l’utilisation du menu Paramétrage.
FRA-10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Télécommande
1. Touche STANDBY/ON
Pour mettre l’appareil sous tension ou hors tension.
2. Touches numériques
3. Touche DISC MENU (numéro 4)
Affiche le menu disque.
1
2
12
13
4. Touche ZOOM (numéro 7)
Permet d’agrandir l’image DVD.
3
4
5
14
15
5. Touche INFO
Pour afficher le mode du disque courant.
16
17
6. Touches SEARCH (
/
)
6
7
8
Permet une recherche avant ou arrière.
18
7. Touche STOP (
8. Touches SKIP (
)
/
)
Utilisez pour sauter un titre, chapitre ou piste.
9. Touche MENU
19
9
10
Pour afficher le menu des réglages du lecteur DVD.
10. Touche ENTER/¦
11
20
Déplacez la touche ENTER vers le haut/bas ou vers la
gauche/droite pour choisir des options de menus.
11. Touche EXIT
Pour quitter le menu à l’écran.
12. Touche OPEN/CLOSE (
)
Pour ouvrir et fermer le tiroir à disque.
13. Touche AUDIO (numéro 5)
Appuyez sur cette touche pour modifier les options audio.
14. Touche REPEAT (numéro 6)
Pour répéter un titre ou tous les titres.
15. Touche SUBTITLE (numéro 9)
16. Touche VIDEO SEL.
Changement du mode sortie Video
( I SCAN - P SCAN)
17. Touche EZ VIEW (numéro 0)
Le format d’image peut facilement être adapté au
format de votre écran de télévision (16/9 ou 4/3).
18. Touche PLAY/PAUSE (
Pour commencer/suspendre la lecture.
19. Touche RETURN
)
Pour revenir au menu précédent.
20. Touche CANCEL
Pour supprimer le menu ou l’affichage à l’écran.
FRA-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapitre 2
BRANCHEMENTS
Choix de la connexion
Cette page présente quelques exemples de connexions généralement utilisées pour raccorder le
lecteur DVD au téléviseur ou à d’autres appareils.
Avant de connecter le lecteur DVD
- Avant de connecter ou de déconnecter les câbles, assurez-vous que le lecteur DVD, le téléviseur
et les autres appareils sont bien débranchés de la prise secteur.
- Pour obtenir des informations supplémentaires relatives aux éléments ajoutés (un téléviseur, par
exemple), reportez-vous aux modes d’emploi de ces éléments.
Connexion à un téléviseur (prise HDMI) (DVD-F1080 uniquement)
1
À l’aide du câble HDMI-HDMI, raccordez la prise HDMI OUT
située à l’arrière du lecteur DVD à la prise HDMI IN de votre
téléviseur.
2
Appuyez sur le sélecteur d’entrée de la télécommande de votre
téléviseur jusqu’à ce que le signal HDMI du lecteur DVD
câble HDMI
(non fourni)
apparaisse à l’écran.
Connexion à un téléviseur (prise DVI) (DVD-F1080 uniquement)
1
À l’aide d’un câble HDMI-DVI (non compris), raccordez la prise
HDMI OUT située à l’arrière du lecteur DVD à la prise DVI IN
de votre téléviseur.
2
A l’aide des câbles audio, raccordez les sorties AUDIO OUT
(rouge et blanche) situées à l’arrière du lecteur DVD aux
entrées AUDIO IN (rouge et blanche) de votre téléviseur.
Allumez le lecteur DVD et le téléviseur.
BLANC
ROUGE
ROUGE
Câble audio
BLANC
câble HDMI-DVI
(non fourni)
3
Appuyez sur le sélecteur d’entrée de la télécommande de votre
téléviseur jusqu’à ce que le signal DVI du lecteur DVD
apparaisse à l’écran.
FRA-12
Download from Www.Somanuals.com. All Manuals Search And Download.
BRANCHEMENTS
Spécifications Vidéo HDMI
- Il se peut que certaines résolutions de sortie HDMI ne soient pas disponibles sur votre TV.
- Référez-vous au manuel de l’utilisateur de votre TV.
- Si un câble HDMI ou HDMI-DVI est branché sur le téléviseur, la sortie du lecteur DVD bascule
automatiquement sur HDMI/DVI au bout de 10 secondes.
- Résolution HDMI change dans l’ordre suivant : 480p, 720p, 1080i et 1080p.
- Si vous raccordez le câble HDMI à un téléviseur Samsung, il vous est facile d’exploiter le lecteur DVD à l’aide
de la télécommande du téléviseur (disponible uniquement avec les téléviseurs Samsung pouvant accueillir
l’option Anynet+ (HDMI-CEC).) (Voir la page 55-56).
- Veuillez vérifier la présence du logo
l’option Anynet+.)
(si votre téléviseur possède le logo
, il peut accueillir
• HDMI (High Definition Multimedia Interface)
HDMI est une interface qui permet une transmission numérique des données vidéo et audio par un seul
connecteur. En utilisant HDMI, le lecteur DVD transmet un signal vidéo et audio numérique et affiche une
image vive sur un téléviseur muni d’une prise HDMI.
• Description de la connexion HDMI
Connecteur HDMI – les données vidéos non compressées et les données audio numériques (données
LPCM par trames).
- Bien que le lecteur utilise un câble HDMI, il n’émet qu’un signal numérique pur vers la TV.
- Si la TV ne supporte pas HDCP (High-bandwidth Digital content protection), le bruit d’écran apparaît à
l’écran.
• Pourquoi Samsung utilise HDMI?
Les TV analogiques nécessitent un signal vidéo/audio analogique. Cependant, les données transmises à
la TV lors de la lecture d’un DVD sont numériques. De ce fait, un convertisseur numérique vers
analogique (sur le lecteur dvd) ou un convertisseur analogique vers numérique (sur la TV) est nécessaire.
Pendant cette conversion, la qualité d’image se dégrade à cause du bruit ou de la perte du signal. DVI est
une technologie plus avancée car elle ne nécessite aucune conversion N/A : c’est un signal numérique pur
depuis le lecteur jusqu’à votre TV.
• Qu’est-ce HDCP?
HDCP (High-bandwidth Digital Content Protection) est un système de protection contre la copie du
contenu du DVD émis par HDMI/DVI. Il fournit un lien numérique sécurisé entre la source (PC, DVD, etc.)
et le dispositif d’affichage (TV, projecteur, etc.). Le contenu est encrypté sur le dispositif source afin
d’empêcher des copies non autorisées.
FRA-13
Download from Www.Somanuals.com. All Manuals Search And Download.
BRANCHEMENTS
Raccordement à un téléviseur (balayage progressif)
1
À l’aide de câbles de composant vidéo (non compris),
raccordez les prises COMPONENT VIDEO OUT situées à
l’arrière du lecteur DVD aux prises COMPONENT IN de votre
téléviseur.
2
ROUGE
VERT
BLEU
A l’aide des câbles audio, raccordez les sorties AUDIO OUT
(rouge et blanche) situées à l’arrière du lecteur DVD aux
entrées AUDIO IN (rouge et blanche) de votre téléviseur.
Allumez le lecteur DVD et le téléviseur.
ROUGE
BLANC
3
Appuyez sur le sélecteur d’entrée de la télécommande de votre
Câble audio
téléviseur jusqu’à ce que le signal de composant du lecteur
DVD apparaisse à l’écran.
Câble vidéo composante
(non fourni)
ROUGE
BLANC
VERT
BLEU
ROUGE
4
Réglez la sortie Video Out sur P-SCAN dans le menu
Configuration de l’affichage. (voir pp. 50-52).
Vous pouvez utiliser la touche VIDEO SEL. pour changer le
mode de ”Video Output(sortie vidéo)”. (voir pp. 16)
Affichage en mode Balayage progressif
- Reportez-vous au manuel d’utilisation de votre téléviseur pour vérifier si celui-ci prend en charge le
balayage progressif. Si tel est le cas, suivez les instructions du manuel d’utilisation du téléviseur
relatives aux réglages du balayage progressif dans les menus du téléviseur.
- En fonction du modèle de votre téléviseur, le branchement peut différer de celui représenté sur le
schéma ci-dessus.
Remarque
- Qu’est-ce que le balayage progressif ?
Le balayage progressif se caractérise par deux fois plus de lignes que le mode de balayage entrelacé.
Le mode Balayage progressif offre une meilleure qualité d’image.
FRA-14
Download from Www.Somanuals.com. All Manuals Search And Download.
BRANCHEMENTS
Raccordement à un téléviseur (affichage entrelacé)
- Connexion à un téléviseur à l’aide des câbles vidéo composante (Component).
- Profitez d’images en haute définition dotées d’un rendu des couleurs parfait. Le procédé
B
Component video sépare les composantes de l’image en signaux noir et blanc (Y), bleu (P ) et
R
rouge (P ) afin d’offrir des images nettes et propres. (les signaux audio sont transmis par
l’intermédiaire de la sortie audio).
1
À l’aide de câbles de composant vidéo (non compris),
raccordez les prises COMPONENT VIDEO OUT situées à
l’arrière du lecteur DVD aux prises COMPONENT IN de votre
téléviseur.
2
ROUGE
BLEU
VERT
A l’aide des câbles audio, raccordez les sorties AUDIO OUT
(rouge et blanche) situées à l’arrière du lecteur DVD aux
entrées AUDIO IN (rouge et blanche) de votre téléviseur.
Allumez le lecteur DVD et le téléviseur.
ROUGE
BLANC
3
Appuyez sur le sélecteur d’entrée de la télécommande de votre
téléviseur jusqu’à ce que le signal de composant du lecteur
DVD apparaisse à l’écran.
Câble audio
Câble vidéo composante
(non fourni)
ROUGE
BLANC
ROUGE
VERT
BLEU
4
Réglez la sortie Video Out sur I-SCAN dans le menu
Configuration de l’affichage. (voir pp. 50-52).
Vous pouvez utiliser la touche VIDEO SEL. pour changer le
mode de ”Video Output(sortie vidéo)”. (voir pp. 16)
Remarque
- Si vous souhaitez relier l’appareil à un amplificateur, reportez-vous à la rubrique Raccordement d’un
amplificateur. (voir pp. 17-18).
- Selon la marque de votre téléviseur, la prise Component peut être repérée par “R-Y, B-Y, Y” ou “Cr, Cb, Y” et
R
B
non par “P , P , Y”. Le nombre et l’implantation des prises peuvent varier en fonction de votre téléviseur.
Veuillez vous reporter au manuel d’utilisation de celui-ci pour plus de détails.
FRA-15
Download from Www.Somanuals.com. All Manuals Search And Download.
BRANCHEMENTS
Raccordement à un téléviseur (sortie Video)
1
A l’aide des câbles vidéo/audio, raccordez les sorties VIDEO
(jaune)/AUDIO (rouge et blanche) OUT situées à l’arrière du
lecteur DVD aux entrées VIDEO (jaune)/AUDIO (rouge et
blanche) IN de votre téléviseur.
2
Allumez le lecteur DVD et le téléviseur.
ROUGE
ROUGE
JAUNE
BLANC
Câble audio
Câble vidéo
JAUNE
BLANC
3
Appuyez sur le sélecteur d’entrée de la télécommande de votre
téléviseur jusqu’à ce que le signal vidéo du lecteur DVD
apparaisse à l’écran.
Remarque
- Un bruit peut se faire entendre si le câble audio est trop proche du cordon d’alimentation.
- Si vous souhaitez relier l’appareil à un amplificateur, reportez-vous à la rubrique Raccordement d’un
amplificateur. (voir pp. 17-18).
- Le nombre et l’implantation des prises peuvent varier en fonction de votre téléviseur. Veuillez vous reporter
au manuel d’utilisation de celui-ci pour plus de détails.
- Si votre téléviseur est équipé d’une entrée audio, raccordez-la à la sortie [AUDIO OUT] (prise blanche de
gauche) du lecteur DVD.
- Si vous appuyez sur la touche VIDEO SEL (SÉL. VIDÉO) tandis que le lecteur DVD est en mode de lecture,
arrêt, ou qu'aucun disque n'est présent. Le mode de sortie vidéo s’affiche selon la séquence suivante :
(I-SCAN ➝ P-SCAN)
FRA-16
Download from Www.Somanuals.com. All Manuals Search And Download.
BRANCHEMENTS
Connexion à un système audio (amplificateur deux canaux)
1
A l’aide des câbles audio, raccordez les sorties AUDIO OUT
(rouge et blanche) situées à l’arrière du lecteur DVD aux
entrées AUDIO IN (rouge et blanche) de votre téléviseur.
2
À l’aide du ou des câble(s) vidéo, raccordez les prises VIDEO,
COMPONENT OUT ou HMDI OUT situées à l’arrière du
lecteur DVD à la prise VIDEO, COMPONENT ou DVI IN de
votre téléviseur, de la façon décrite aux pages 12 à 16.
BLANC
ROUGE
ROUGE
3
Allumez le lecteur DVD, le téléviseur et l’amplificateur.
Câble audio
BLANC
amplificateur deux
canaux
4
Appuyez sur le bouton de sélection d’entrée de l’amplificateur
et choisissez source externe pour entendre le son transmis
par le lecteur DVD.
Pour régler l’entrée audio de l’amplificateur, reportez-vous au
mode d’emploi de l’amplificateur.
Remarque
- Veillez à baisser le volume avant d’allumer l’amplificateur afin d’éviter tout “claquement” des haut-
parleurs. Celui-ci pourrait endommager les enceintes et provoquer des lésions auditives chez les
personnes.
- Veillez également à régler les paramètres audio du menu en fonction des caractéristiques de l’amplificateur
(voir pp. 48-49).
- L’implantation des prises peut varier en fonction de l’amplificateur. Veuillez vous reporter au manuel
d’utilisation de celui-ci pour plus de détails.
FRA-17
Download from Www.Somanuals.com. All Manuals Search And Download.
BRANCHEMENTS
Connexion à un système audio (amplificateur Dolby digital, MPEG2 ou DTS)
1
Si vous utilisez un câble coaxial (non fourni), raccordez la sortie
DIGITAL AUDIO OUT (COAXIAL) située à l’arrière du lecteur
DVD à l’entrée DIGITAL AUDIO IN (COAXIAL) de votre
amplificateur.
2
À l’aide du ou des câble(s) vidéo, raccordez les prises VIDEO,
COMPONENT ou HDMI OUT situées à l’arrière du lecteur DVD
à la prise VIDEO, COMPONENT ou HDMI-DVI IN de votre
téléviseur, de la façon décrite aux pages 12 à 16.
3
Allumez le lecteur DVD, le téléviseur et l’amplificateur.
Cable coaxial
(non fourni)
amplificateur Dolby
digital ou DTS
4
Appuyez sur le bouton de sélection d’entrée de l’amplificateur
et choisissez source externe pour entendre le son transmis
par le lecteur DVD.
Pour régler l’entrée audio de l’amplificateur, reportez-vous au
mode d’emploi de l’amplificateur.
Remarque
- Veillez à baisser le volume avant d’allumer l’amplificateur afin d’éviter tout “claquement” des haut-
parleurs. S’il est “Off(désactivé)”, vous n’entendrez aucun son ou vous entendrez un son sourd.
- Veillez également à régler les paramètres audio du menu en fonction des caractéristiques de l’amplificateur
(voir pp. 48-49).
- L’implantation des prises peut varier en fonction de l’amplificateur. Veuillez vous reporter au manuel
d’utilisation de celui-ci pour plus de détails.
FRA-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapitre 3
FONCTIONS ELEMETAIRES
Lecture des disques
Avant la lecture
- Allumez votre téléviseur et réglez-le sur l’entrée vidéo qui convient à l’aide de la télécommande
du téléviseur.
- Si vous avez branché le système audio externe, allumez votre système audio et réglez-le sur le
bon canal d’entrée audio.
Dès que vous appuyez sur la touche DVD POWER, après branchement du lecteur,
l’écran suivant apparaît : Pour choisir une langue, appuyez sur une touche numérique.
(Cet écran s’affiche uniquement lorsque vous branchez le lecteur DVD pour la première
fois.) Si vous ne définissez pas la langue dans l’écran de démarrage, les réglages
peuvent changer à chaque mise sous ou hors tension de l’appareil. Veillez par
conséquent à sélectionner la langue d’affichage souhaitée.
Après validation, vous pouvez néanmoins la modifier en appuyant sur le bouton
situé en façade de l’appareil pendant plus de cinq secondes, aucun disque n’étant
chargé. L’écran SELECT MENU LANGUAGE (SELECTION DE LA LANGUE
D’AFFICHAGE) réapparaît afin que vous puissiez activer la langue de votre choix.
Lecture
1
Appuyez sur la touche
OPEN/CLOSE ( ).
Le voyant STANDBY s’éteint
et le tiroir à disque s’ouvre.
N’insérez qu’un DVD à la fois. Si vous en
insérez plusieurs, ils ne pourront être lus et
risqueront d’endommager le lecteur.
2
Placez le disque avec soin
sur le tiroir, étiquette
de présentation du disque
vers le haut.
Fonction mémoire
3
Lorsque vous arrêtez la lecture, l’appareil
mémorise l’endroit où vous l’avez arrêtée. Si
vous appuyez sur PLAY/PAUSE ( ) pour
recommencer, il reprendra la lecture là où vous
l’avez quittée.
Appuyez sur la touche
PLAY/PAUSE ( ) ou
OPEN/CLOSE ( ) pour
fermer le tiroir à disque.
FRA-19
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS ELEMETAIRES
Remarque
4
- Si le lecteur n’est pas utilisé pendant plus d’une
minute, l’économiseur d’écran apparaît et l’écran
s’ouvre et se ferme en fondu de façon continue.
Appuyez sur PLAY/PAUSE ( ) (Lecture) pour
poursuivre la lecture.
Arrêt de la lecture
Appuyez sur la touche
STOP ( ) pendant la
lecture.
- Si le lecteur reste en mode arrêt pendant plus de
30 minutes, il se met automatiquement hors
tension. (Fonction de mise hors tension
automatique)
5
Retrait du disque
Appuyez sur OPEN/CLOSE
(
).
L’image devient fixe et il n’y a plus de son.
Pour reprendre appuyez à nouveau sur la
touche PLAY/PAUSE ( ) .
6
Interruption de la lecture
Appuyez sur la touche
PLAY/PAUSE ( ) sur la
télécommande
Remarque
durant la lecture.
Si vous laissez le lecteur en pause, l’appareil se
met en position arrêt après 5 minutes.
En mode ralenti, le son est coupé.
Appuyez sur PLAY/PAUSE ( ) pour revenir au
mode normal.
7
Lecture au ralenti
Appuyez sur le bouton
SEARCH (
) et
/
maintenez-le enfoncé pour
choisir la vitesse de lecture
(1/8, 1/4 ou 1/2 de la vitesse
normale) en mode PAUSE.
Remarque
Le symbole ( ) indique une pression sur une
touche invalide.
FRA-20
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS ELEMETAIRES
Recherche et saut de pchapitre ou de plage
Vous pouvez rechercher rapidement un chapitre ou une plage que vous appréciez pendant la
lecture.
Recherche par chapitre ou plage
Si vous souhaitez accélérer la vitesse de
recherche sur le DVD ou le CD, appuyez sur le
bouton et maintenez-le enfoncé.
En cours de lecture,
enfoncez le bouton
SEARCH ( or
) de
DVD 2X, 4X, 64X, 128X
CD 2X, 4X, 8X
cette dernière pendant plus
d’une seconde.
Remarque
- La vitesse de lecture réelle peut être différente
de la vitesse indiquée pour cette fonction.
- Aucun son n’est émis en mode Recherche (sauf
si l’appareil lit un CD).
Saut des plages
Appuyez sur les touches
SKIP (
ou
) pendant
la lecture.
- Si vous appuyez sur SKIP ( ) pendant la lecture d’un
DVD, vous passerez au chapitre suivant. Si vous
appuyez sur SKIP ( ), vous retournerez au début du
chapitre. En appuyant de nouveau sur la touche, vous
passerez au début du chapitre précédent.
- Lors de la lecture d’un CD, si vous appuyez sur SKIP
(
), vous passerez à la plage suivante. Si vous
appuyez sur SKIP ( ), vous retournerez au début de
la plage. Une nouvelle pression vous permettra d’avoir
le début de la plage précédente.
FRA-21
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS ELEMETAIRES
Utilisation de la fonction d’affichage
Lecture d’un DVD/MPEG4
Vous pouvez sélectionner Info dans le menu de
fonctions en appuyant sur le bouton MENU.
1
Lors de la lecture, appuyez
sur la touche INFO de
la télécommande.
DVD
2
Servez-vous des boutons
/ pour sélectionner
l’élément souhaité.
DVD
Title
001
002
Chapter
Time
00:00:13
ENG 5.1CH
Non
Audio
Subtitle
Enter
MPEG4
001
00:00:13
MP3 1/8
Non
Enter
Vous pouvez vous servir des touches
numériques de la télécommande pour accéder
directement à un titre, à un chapitre ou pour
démarrer la lecture à l’heure souhaitée.
3
Utilisez les boutons ¦/
pour effectuer le réglage
souhaité et appuyez sur
ENTER.
4
Pour fermer l’écran,
appuyez à nouveau sur la
touche INFO.
FRA-22
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS ELEMETAIRES
Remarque
Permet de sélectionner le titre souhaité parmi plusieurs titres sur le disque.
Par exemple si un DVD contient plus d’un film, chacun des films porte un titre d’identification.
Title
Chapter
Le contenu de la plupart des disques DVD est divisé en chapitres qui vous permettent de repérer
rapidement un passage particulier.
Permet la lecture du film à l’heure désirée. Pour cela, vous devez indiquer l’heure de début comme
référence. La fonction de recherche temporelle n’est pas compatible avec certains disques.
Time
Indique la langue de la piste sonore du film. Dans l’exemple, la piste sonore en lecture en mode
Audio 5.1CH est en anglais.
Un disque DVD peut comporter un maximum de huit pistes sonores.
Indique la langue des sous-titres sur le disque. Vous pouvez choisir cette langue ou, si vous le
préférez, désactiver la fonction des sous-titres.
Subtitle
Un disque DVD peut comporter un maximum de 32 sous-titres.
Utilisation du menu Disque et pdu menu Titres
Utilisation du menu Disque (DVD)
1
Lors de la lecture d’un
disque DVD, appuyez sur
la touche MENU de la
télécommande.
2
Utilisez les boutons /
Appuyez sur la touche
ENTREE pour accéder
au Menu Disque
Remarque
pour sélectionner Disc
Menu puis appuyez sur
ou sur ENTER.
- Le menu Disque peut ne pas être compatible
avec certains disques.
- Vous pouvez également accéder au menu
Disque par l’intermédiaire du bouton DISC
Enter
Return
Menu
MENU de la télécommande.
FRA-23
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS ELEMETAIRES
Utilisation du menu Titres (DVD)
1
Lors de la lecture d’un
disque DVD, appuyez sur
la touche MENU de la
télécommande.
2
Utilisez les boutons /
Appuyez sur la touche
ENTREE pour accéder
au Menu Titres
pour sélectionner Title
Menu puis appuyez sur
ou sur ENTER.
Remarque
- Le menu Titres peut ne pas être compatible avec
certains disques.
- Le menu Titres ne s’affiche que si le disque
contient au moins deux titres.
Enter
Return
Menu
Utilisation du menu des fonctionnalités
Utilisation du menu des fonctionnalités (DVD)
1
Lors de la lecture, appuyez
sur la touche MENU.
2
Info
Utilisez les boutons /
Zoom
pour sélectionner Function
puis appuyez sur ou sur
Signet
Répétition
ENTER.
- Info (voir pp. 22 - 23)
EZ View
Angle
- Zoom (voir pp. 34)
Enter
Return
Menu
- Signet (voir pp. 32 - 33)
- Répétition (voir pp. 25)
- EZ View (voir pp. 27 - 28)
- Angle (voir pp. 31)
Vous pouvez également sélectionner
directement les parties de ces fonctions en
utilisant les touches correspondantes de la
télécommande.
3
Utilisez les boutons /
pour sélectionner l’une des
cinq fonctions. Ensuite,
appuyez sur la touche ou
ENTER pour accéder à la
fonction choisie.
- INFO
- ZOOM
- EZ VIEW
- REPEAT
FRA-24
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS ELEMETAIRES
Lecture répétée
Reprenez la lecture de la piste, du chapitre, du titre actuel ou d’une section (p. ex., A-B) ou encore
du disque au complet.
Lecture en DVD
1
Pressez la touche REPEAT.
Le menu répétition apparaît
à l'écran.
La répétition d’un DVD se fait par chapitre.
DVD
2
Chapitre ( ): répète le chapitre en cours de
ENTER REPEAT
Utilisez les boutons ¦/
01
01 A - B
Non
T
lecture.
Title (
pour sélectionner Chapter,
Title ou A-B puis appuyez
sur ENTER.
T
): répète le titre en cours de lecture.
Disque ( ): répète l’intégralité du disque en
cours de lecture.
Plage ( ): répète la plage en cours de lecture.
A-B: répète un segment du disque que vous
avez sélectionné.
Fonction A-B Repeat
1. Appuyez sur le bouton REPEAT de la télécomande.
2. Appuyez sur le bouton ¦/¤pour sélectioner sur la toucheA-B.
3. Appuyez sur le bouton ENTER à l’instant (A) où vous souhaitez faire démarrer la lecture répétée.
B s’affiche automatiquement en surbrillance.
4. Appuyez sur le bouton ENTER à l’instant (B) où la lecture répétée doit s’arrêter.
- Pour repasser en lecture normale, appuyez sur le bouton CANCEL.
Remarque
La fonction A-B REPEAT ne vous permet pas de choisir un instant (B) étant postérieur à l’instant (A)
de moins de cinq secondes.
DVD
3
Pour revenir en mode
ENTER REPEAT
01
01 A - B
Non
T
lecture normale, appuyez
de nouveau sur la touche
REPEAT. Appuyez
ensuite sur la touche ¦/
pour choisir Non et puis
appuyez sur la touche
ENTER.
Remarque
- La lecture répétée peut ne pas s’appliquer sur
certains disques.
FRA-25
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS ELEMETAIRES
Lecture lente
Cette option permet de revoir les scènes contenant du sport, de la danse, de la musique, etc., de
façon à pouvoir les visualiser plus précisément.
Pendant la lecture d’un DVD
1
Lors de la lecture, appuyez
sur la touche PLAY/PAUSE
(
).
2
Appuyez sur la touche
SEARCH (
) et
/
maintenez-le enfoncé pour
choisir la vitesse de lecture
(1/8, 1/4 ou 1/2 moitié de la
vitesse normale) en mode
PAUSE.
FRA-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapitre 4
FONCTIONS AVANCEES
Réglage du rapport d’aspect hauteur-largeur
de l’écran (EZ View)
La lecture d’un DVD et choix du rapport d’aspect (DVD)
Appuyez sur la touche
EZ VIEW.
- La taille de l’écran se
modifie lorsque la touche
est actionnée à plusieurs
reprises.
- Le mode écran zoom
fonctionne différemment
selon la configuration de
l'écran dans le menu
Configuration de l'affichage.
- Pour que le bouton
Pour faire disparaître la barre de rapport de
forme, appuyez sur le bouton CANCEL.
EZ VIEW
Ecran Large
EZ VIEW fonctionne
correctement, vous devez
régler le format d'image
correct dans le menu
Configuration de l'affichage.
(voir pp. 50-52).
Connexion à un téléviseur 16:9
Les disques au rapport d’aspect 4:3
Les disques au rapport d’aspect 16:9
- Format Large
Affichage du DVD au rapport 16:9. L’image s’étire
verticalement.
- Ecran Large
Le contenu des DVD s’affiche au rapport 16:9.
- Ajustement à l’écran
Des bandes noires cachent les parties supérieure et
inférieure de l’écran. Lors de la lecture d’un disque au
rapport d’aspect de 2.35:1, les bandes noires au haut et au
bas de l’écran disparaissent, et l’image s’étire
verticalement. (Dans le cas de certains disques, il se peut
que les bandes noires ne disparaissent pas
complètement.)
- Ajustement à l’écran
Des bandes noires cachent les parties supérieure et
inférieure de l’écran. L’image remplit l’espace entre les
deux bandes et a l’apparence étirée à la verticale.
- Elargissement
Les extrémités et les parties supérieure et inférieure de
l’écran sont amputées, alors que la partie centrale de
l’écran s’agrandit.
- Elargissement
Les extrémités et les parties supérieure et inférieure de
l’écran sont amputées, alors que la partie centrale de
l’écran s’agrandit.
- Ajustement Vertical
Lors du visionnement d’un DVD au rapport d’aspect 4:3 sur
un téléviseur au rapport hauteur-largeur 16:9, l’image est
délimitée d’une bande noire des deux extrémités pour
qu’elle n’ait pas d’apparence étirée horizontalement.
FRA-27
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Connexion à un téléviseur 4:3
Les disques au rapport d’aspect 16:9
Les disques au rapport d’aspect 4:3
- 4:3 Letter Box
Le contenu des DVD s’affiche au rapport 16:9, et une
bande noire apparaît au haut et au bas de l’écran.
- Format Classique
Le contenu des DVD s’affiche au rapport 4:3.
- SCREEN FIT
- 4:3 Pan Scan
Les parties gauche et droite de l'écran sont coupées et la
partie centrale de l'écran 16/9 s'affiche.
Des bandes noires cachent les parties supérieure et
inférieure de l'écran. L'image remplit l'espace entre les
deux bandes et a l’apparence étirée à la verticale.
- Ajustement à l’écran
- Elargissement
Des bandes noires cachent les parties supérieure et
inférieure de l’écran. L’image remplit l’espace entre les
deux bandes et a l’apparence étirée à la verticale.
Les extrémités et les parties supérieure et inférieure de
l’écran sont amputées, alors que la partie centrale de
l’écran s’agrandit.
- Elargissement
Les extrémités et les parties supérieure et inférieure de
l’écran sont amputées, alors que la partie centrale de
l’écran s’agrandit.
Remarque
Dans le cas de certains disques, le comportement du rapport hauteur-largeur de l’écran pourrait différer de
celui décrit ci-dessus.
FRA-28
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Sélection de la langue d’écoute
Vous pouvez sélectionner rapidement et facilement la langue audio souhaitée à
l'aide du bouton AUDIO.
Utilisation de la touche AUDIO (DVD/MPEG4)
1
Appuyez sur la touche
AUDIO. Le son augmente
ou baisse lorsque la
touche est actionnée à
plusieurs reprises.
Les langues d’écoute
s’inscrivent en abrégé.
DVD
AUDIO
ENG DOLBY DIGITAL 5.1CH
Appuyez sur le bouton
AUDIO situé sur la
télécommande de façon
répétée pour sélectionner le
mode Audio désiré sur un
MPEG-4 puis appuyez sur
ENTER.
MPEG4
AUDIO
PCM 1/2
2
Pour retirer l'icône
AUDIO, appuyez sur le
bouton CANCEL ou
RETURN.
Remarque
- Cette fonction varie en fonction des langues
audio présentes sur le disque et peut ne pas
fonctionner.
- Un disque DVD peut proposer jusqu’à 8 langues
d’écoute.
- Pour bénéficier de la même langue audio à
chaque fois que vous lisez un DVD; Voir la
rubrique “Choix de la langue de la bande sonore”
à la page 45.
FRA-29
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Sélection de la langue des sous-titres
Vous pouvez sélectionner rapidement et facilement un sous-titrage avec la touche
SUBTITLE.
Utilisation de la touche SUBTITLE (DVD/MPEG4)
1
Appuyez sur la touche
SUBTITLE.
Le sous-titre change
lorsque vous appuyez sur
la touche de manière
répétée.
Les langues des sous-titres
DVD
sont indiquées en abrégé.
SUBTITLE
Non
MPEG4
En fonction du type de
DivX, une option de
sous-titrage externe
s’affiche.
External Subtitle Off
readme.TXT
Enter
Return
Menu
Appuyez sur le bouton
MPEG4
SUBTITLE situé sur la
télécommande de façon
répétée pour sélectionner la
langue désirée pour les sous-
titres sur un MPEG-4 puis
appuyez sur ENTER.
SUBTITLE
Non
2
Pour retirer l'icône
SUBTITLE, appuyez sur
le bouton CANCEL ou
RETURN.
Remarque
- Selon les DVD, vous devez modifier le sous-titre
souhaité dans le “Disc Menu(menu Disque)”.
Appuyez sur le bouton DISC MENU.
- La possibilité d’utiliser cette fonction dépend de
la langue enregistrée sur le disque.
- Un disque DVD peut proposer jusqu’à 32
langues.
- Pour bénéficier de la même langue de sous-titre
à chaque fois que vous lisez un DVD; Voir la
rubrique “Choix de la langue des sous-titres” à la
page 46.
FRA-30
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Sélection de l’angle de prise de vue à l’écran
Certains DVD permettent de voir une séquence sous plusieurs angles de vue.
Modification de l’angle de vue (DVD)
Si le disque contient des angles multiples, la marque ANGLE apparaît à l’écran.
1
Pendant la lecture ou en
mode pause, appuyez
sur la touche MENU.
2
Info
Utilisez les boutons /
Zoom
Signet
pour sélectionner
Function puis appuyez
sur ou sur ENTER.
Répétition
EZ View
Angle
Enter
Return
Menu
3
Info
Utilisez les boutons /
pour sélectionner Angle
puis appuyez sur ou
sur ENTER.
Zoom
Signet
Répétition
EZ View
Angle
Enter
Return
Menu
Remarque
- Si le disque a un angle, cette fonction ne
fonctionne pas. Les disques ayant cette
caractéristique sont cependant très rares.
- Ces fonctions peuvent ne pas être compatibles
avec certains disques.
4
4/6
Appuyez sur la touche
¦/ de la
télécommande pour
sélectionner l'angle
souhaité.
FRA-31
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Utilisation des repères
Cette fonction vous permet d’insérer des signets dans les diverses sections du DVD afin d’y
accéder rapidement à n’importe quel moment.
Utilisation des repères (DVD)
1
Pendant la lecture,
appuyez sur la touche
MENU.
2
Info
Utilisez les boutons /
Zoom
pour sélectionner Function
puis appuyez sur ou sur
ENTER.
Signet
Répétition
EZ View
Angle
Enter
Return
Menu
3
Info
Utilisez les boutons /
pour sélectionner Signet
puis appuyez sur ou sur
ENTER.
Zoom
Signet
Répétition
EZ View
Angle
Enter
Return
Menu
4
Lorsque vous avez trouvé
la séquence que vous
voulez repérer, appuyez
sur la touche ENTER.
Vous pouvez marquer
simultanément jusqu’à
trois scènes différentes.
CANCEL
Remarque
- Avec certains disques, cette fonction peut ne pas
être disponible.
FRA-32
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Rappel d’une séquence repérée
1~3
Les trois premières étapes
sont identiques à celles de
la rubrique “Utilisation de
la fonction Signet” en
page 32.
CANCEL
4
Appuyez sur les boutons
¦/ pour sélectionner
une scène marquée.
5
Appuyez sur
PLAY/PAUSE (
passer à la séquence
marquée.
) pour
Suppression d’un repère
1~3
Les trois premières étapes
sont identiques à celles de
la rubrique “Utilisation de
la fonction Signet” en
page 32.
4
CANCEL
Appuyez sur les boutons
¦/ pour sélectionner le
numéro du signet à
supprimer.
5
Appuyez sur la touche
CANCEL pour effacer le
numéro du signet.
FRA-33
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Utilisation des fonctions avancées
Utilisation des fonctions avancées (DVD)
1
Pendant la lecture ou en
mode pause, appuyez
sur la touche MENU.
2
Info
Utilisez les boutons /
Zoom
pour sélectionner Function
puis appuyez sur ou sur
ENTER.
Signet
Répétition
EZ View
Angle
Enter
Return
Menu
3
Info
Utilisez les boutons /
pour sélectionner Zoom
puis appuyez sur ou sur
ENTER.
Zoom
Signet
Répétition
EZ View
Angle
Enter
Return
Menu
En cours de lecture d’un DVD, appuyez sur
ENTER pour effectuer un zoom avant de
2X/4X/2X/Normal dans l’ordre.
4
Appuyez sur les boutons
/ ou ¦/ pour
sélectionner la partie de
l’écran sur laquelle vous
souhaitez effectuer un
zoom avant.
Appuyez sur ENTER.
FRA-34
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Menu Clips pour MP3/WMA/JPEG/MPEG4/CD Audio
Les CD audio ou disques au format MP3/WMA/JPEG/MPEG4 contiennent des chansons, des
images ou des vidéos qui peuvent être organisées en dossiers comme le montre l’exemple ci-
dessous. Leur système de fonctionnement est similaire à celui utilisé par un ordinateur pour
mettre des fichiers dans différents dossiers.
Ouvrez le tiroir de disques.
Arrêt
Non
Placez le disque sur le
plateau.
Fermez le tiroir.
Le tiroir se ferme et cet
écran s’affiche.
00:00:00
W M A
J P E G
M P 3
M P E G 4
Menu
Enter
Return
-
-
-
-
-
: Icône d’un fichier MP3.
: Icône d’un fichier WMA.
: Icône d’un fichier JPEG.
: Icône d’un fichier AVI.
-
-
-
: Nom du fichier en cours de lecture.
: Durée de lecture actuelle.
: Mode de lecture actuelle : Il y a 4 modes,
activés grâce à la touche REPEAT.
- Non : Lecture normale
- Plage : Répétition de la piste actuelle.
- Folder : Répétition du dossier actuel.
- Aléatoire : Les fichiers du disque sont lus
dans un ordre aléatoire.
:
Icône d’un fichier CD Audio.
-
-
: Icône d’un dossier.
: Icône du dossier actuel.
Remarque
• Lorsque vous lisez un fichier MPEG4, la fonction VIDEO SEL. ne fonctionne qu’en mode Stop (Arrêt).
Modifier un Dossier
Le dossier peut être sélectionné à la fois en mode Arrêt et en mode Lecture.
- Dossier Parent
Appuyez sur la touche RETURN pour accéder au
Root
dossier Parent ou utilisez les touches / pour
WMA
sélectionner “..” et appuyez sur ENTER pour accéder
au dossier Parent.
JPEG
MP3
Dossler Parent
- Dossier Homologue
Appuyez sur les boutons / pour sélectionner le
MUSIC
Dossler actuel
Sous-dossiers
dossier souhaité, puis appuyez sur ENTER.
1st
2nd
- Sous-Dossier
Appuyez sur les boutons / pour sélectionner le
dossier souhaité, puis appuyez sur ENTER.
SONG FILE 1
SONG FILE 2
Dossiers Collègues
SONG FILE 3
MPEG4 FILES
FRA-35
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Lecture de MP3/WMA/CD Audio
Un seul type de fichier sera lu et non
les deux si un disque contient des
fichiers MP3 et WMA.
Arrêt
Non
1
00:00:00
Ouvrez le tiroir de disques.
Placez le disque sur le
plateau.
W M A
J P E G
M
P
3
M
P
E G 4
Fermez le tiroir.
Menu
Enter
Return
2
Appuyez sur les boutons
/ ou ¦/ pour
sélectionner un fichier
musical.
Appuyez sur ENTER pour
démarrer la lecture du
fichier musical.
Lecture
Non
00:00:23
B e c a u s e Yo u
. . .
B e c a u s e Yo u
C
a
c
t u s
S a d D a y u
Wo n d e r f u l
REPEAT
Repeat
Enter
Return
Lecture Répétition/Aléatoire
1
Appuyez sur la touche
REPEAT pour modifier le
mode de lecture.
Il y a quatre modes; Non,
Plage, Folder et Aléatoire.
- Non : Lecture normale
- Plage : Répétition du fichier musical actuel.
- Folder : Répétition des fichiers musicaux ayant la même
extension dans le dossier actuel.
- Aléatoire : Les fichiers musicaux ayant la même extension sur
le disque sont lus dans un ordre aléatoire.
Pour reprendre la lecture normale, appuyez sur la touche CANCEL.
FRA-36
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
CD-R fichier MP3/WMA
- Utilisez un taux de compression d’au moins 64 Kpbs
pour l’enregistrement des fichiers WMA.
La qualité sonore des fichiers WMA dépend principalement
du taux de compression ou de décompression choisi.
L'obtention d'un CD audio de bonne qualité sonore
nécessite une fréquence d'échantillonnage
Lorsque vous enregistrez des fichiers MP3/WMA
sur le CD-R, veuillez vous reporter à ce qui suit.
- Les fichiers MP3 ou WMA doivent être enregistrés avec
le format ISO 9660 ou JOLIET.
Le format ISO 9660 et les fichiers MP3 ou WMA Joliet sont
compatibles avec les systèmes d'exploitation DOS et
Windows de Microsoft, ainsi qu'avec le système Mac
d'Apple. Ces deux formats sont les plus couramment
utilisés.
analogique/numérique (conversion sous un format WMA) à
une fréquence comprise entre 64 Kbps et 192 Kbps. À
l’inverse, les fichiers comportant des fréquences
d’échantillonnage moins élevées (64 Kbps ou moins) ou
plus élevées (192 Kbps ou plus) ne seront pas
correctement lus.
- Attribuez aux fichiers MP3 ou WMA un nom ne
dépassant pas 8 caractères et accompagné d'une
extension fichier “.mp3 .wma”.
Format de nom général : Titre.mp3. ou Titre.wma. Lors de
la création du titre, vérifiez que vous lui attribuez 8
caractères ou moins, sans espace et évitez d'y inclure des
caractères spéciaux comme (.,/,\,=,+).
- N'essayez pas d'enregistrer des fichiers MP3 protégés
par des droits d'auteur.
Certains fichiers sont sécurisés afin d'éviter toutes copies
illégales. Ils sont de types suivants : Windows MediaTM
(marque déposée de Microsoft Inc) et SDMITM (marque
déposée de la SDMI Foundation). Leur copie est
impossible.
- Lors de l'enregistrement des fichiers MP3, utilisez un
transfert de décompression d'un débit minimum de 128
Kbps.
La qualité sonore des fichiers MP3 dépend principalement
du taux de compression ou de décompression choisi.
L'obtention d'un CD audio de bonne qualité sonore
nécessite une fréquence d'échantillonnage
analogique/numérique (conversion sous un format MP3) à
une fréquence entre 128 Kbps et 160 Kbps. Choisir des
fréquences plus élevées (192 Kbps ou plus) donnera
rarement de meilleurs résultats. A l'inverse, les fichiers
comportant des fréquences d'échantillonnage inférieures à
128 Kbps ne seront pas correctement lus.
- Important:
Les recommandations ci-dessus n'offrent aucune garantie
quant à la bonne restitution des enregistrements MP3 ou
n'en certifient pas la qualité sonore. Vous noterez que
certaines des technologies et méthodes d'enregistrement
de fichiers MP3 sur CD-R n'offrent pas une restitution
optimale sur le lecteur DVD (altération de la qualité sonore
et dans certains cas, impossibilité de lecture des fichiers).
- Cette unité possède une capacité de lecture de 500 fichiers
et de 500 dossiers par disque.
FRA-37
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Lecture de MPEG4
Fonction lecture MPEG4
Les fichiers AVI utilisés contiennent les données audio et vidéo. Seuls les fichiers au
format AVI dotés de l'extension “.avi” peuvent être lus.
Arrêt
Non
1
00:00:00
Ouvrez le tiroir de
disques.
W M A
J P E G
M P 3
Placez le disque sur le
plateau.
M P E G 4
Fermez le tiroir.
Menu
Enter
Return
2
Utilisez les touches ꢀ
¦ꢀ pour sélectionner un
fichier avi (DivX/XviD) puis
appuyez sur le touche
ENTER.
Arrêt
Non
00:00:00
/ M P E G 4
. . .
T
a 0 1 _ d i v x 5 1 b - 8
a 0 2 _ d i v x 5 0 5 b - 8
a 0 3 _ d i v x 5 0 2 s p - 8
a 0 4 _ d i v x 4 1 2 - 8
Menu
Enter
Return
Répétition de la lecture
Pour repasser en lecture normale,
appuyez sur le bouton CANCEL.
Appuyez sur le touche
REPEAT pour changer de
mode de lecture. Il existe 3
modes : Non, Folder, Titre.
- Folder : répète les fichiers AVI possédant la même extension
dans le dossier actuel.
- Titre : répète le titre en cours de lecture.
FRA-38
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Description des fonctions disponibles pour
les fichiers MPEG-4
imiLes messages d’avertissement pouvant s’afficher durant la
lecture d’un fichier DivX sont :
1. Non autorisé
Fonction
Description
Page de référence
-
- Un fichier généré avec un code d’enregistrement erroné.
En cours de lecture, appuyez sur
Sauter
ou
Erreur d' autorisation
le touche
ou
pour
(
)
avancer ou reculer de 5 minutes.
Le format de n'est pas soutenu
Pendant la lecture, appuyez
sur les touches de la
télécommande SEARCH
(
ou
) (Recherche
Recherche
ou
-
avancée ou arrière).
(
)
Vous permet d’effectuer une
recherche rapide dans un
fichier AVI. (2X, 4X, 8X)
Enter
Return
Vous permet d’effectuer une
recherche plus lente dans un
fichier AVI.
2. Codec non accueilli
Lecture en
vitesse lente
P 20
P 34
- Les fichiers contenant certains types de codec ou de
version (ex : MP4, AFS et autres codecs à propriété
exclusive) ne sont pas accueillis par ce lecteur.
(1/8X, 1/4X, 1/2X)
2X/4X/2X/Normal dans
l'ordre.
ZOOM
Arrêt
Non
00:00:00
S w e e t V O L
3
- Ces fonctions peuvent ne pas fonctionner selon le
type de fichier MPEG-4.
. . .
Yo u
Le fichier que vous souhaitez lire
comporte des codecs non pris en charge
O n l y y o u
Fichier AVI d'un CD-R
L
o
v
i
n
g
y
o
u
S w e e t V O L
3
Cet appareil peut lire les formats de compression vidéo suivants
dans le format de fichier AVI :
Menu
Enter
Return
- DivX 3.11 ;
- DivX 4 (profil simple MPEG-4) ;
- DivX 5 (profil simple MPEG-4 + fonctions supplémentaires telles
que recherche/affichage
3. Résolution non accueillie
- Les fichiers à résolution plus élevée que celle des
caractéristiques du lecteur ne sont pas accueillis.
bi-directionnel dans les cadres.
Arrêt
Non
Qpel et GMC sont également pris en charge)
- Contenu compatible XviD MPEG-4.
00:00:00
a 0 1 _ d i v x 6 1 b - 6
T
. . .
a 0 1 _ d i v x 6 1 b - 6
a Larésolutiondu fichier que vous tentez
de lire n'est pas prise en charge
Cet appareil prend en charge toutes les résolutions jusqu’au
maximum indiqué ci-dessous.
a
a 0 4 _ d i v x 6 1 2 - 6
Menu
Enter
Return
DivX3.11 & DivX4 & XviD
DivX5
La vitesse peut varier :
L'appareil peut sauter le
décodage des parties à
vitesse très lente et
720 x 480 @30fps
720 x 576 @25fps
: Vitesse maximum : 4Mbps
recommencer à décoder
lorsque la vitesse redevient
normale.
REMARQUE
-
Il est possible que certains fichiers MPEG-4 créés sur un PC ne puissent pas être lus. Seuls les types de Codec, les
versions et les résolutions correspondants aux spécifications sont pris en charge.
- Cet appareil prend en charge les CD-R et les CD-RW enregistrés dans un format MPEG-4 conforme à la
norme “ISO9660”.
FRA-39
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Lecture de CD images
Arrêt
Non
1
00:00:00
Modifiez le dossier que
vous souhaitez.
W M A
J P E G
M P 3
M P E G 4
Menu
Enter
Return
Arrêt
Non
2
0 0 : 0 0 : 0 0
1
Utilisez les boutons /
pour sélectionner un fichier
image dans le menu clips
puis appuyez sur le bouton
ENTER.
. . .
1
2
3
Menu
Enter
Return
3
Appuyez sur la touche INFO
pour afficher le menu.
Appuyez sur les touches
ENTER RETURN
Remarque
- Appuyez sur la touche STOP pour revenir au
menu clips.
¦
/ pour sélectionner le
- Avec un CD d’images Kodak, l’unité affiche la
photo directement, il n’y a pas de menu clips.
menu que vous souhaitez
visualiser, puis appuyez sur
la touche ENTER.
•
•
•
: Les photos s’affichent automatiquement l’une après
l’autre à intervalle de 6 secondes.
Rotation
: Les photos s’affichent automatiquement l’une après
l’autre à intervalle de 12 secondes.
:À chaque pression sur la touche ENTER, l’image
pivote de 90 degrés dans le sens des aiguilles d’une
montre.
: Les photos s’affichent automatiquement l’une après
l’autre à intervalle de 18 secondes.
Zoom
: Appuyez sur les boutons / ou ¦
/ pour
ENTER RETURN
VITESSE:
sélectionner la partie de l’écran sur laquelle vous
souhaitez effectuer un zoom avant.
À chaque pression sur la touche ENTER, l’image
agrandit jusqu’à 2X.
Diaporama
•
: L’unité passe au mode Diaporama.
• Avant de commencer la lecture en mode Diaporama,vous
devez régler l’intervalle d’affichage des photos.
Remarque
- Selon la taille du fichier, les intervalles entre les images peuvent différer des intervalles sélectionnées.
- Si vous n’appuyez sur aucune touche, par défaut le diaporama démarre automatiquement par intervalle de
10 secondes.
FRA-40
Download from Www.Somanuals.com. All Manuals Search And Download.
FONCTIONS AVANCEES
Lecture de fichiers MP3-JPEG
Vous pouvez lire un fichier JPEG en ajoutant de la musique en fond sonore.
1
Appuyez sur le boutons
/¤pour sélectionner un
fichier MP3 dans le menu
des mélodies, puis
appuyez sur le bouton
ENTER.
La musique est lue dés le début.
2
Appuyez sur le boutons
/¤pour sélectionner un
fichier JPEG dans le
menu des mélodies, puis
appuyez sur le bouton
ENTER.
Remarque
Les fichier MP3 et JPEG doivent se trouver
sur le même disque.
3
Appuyez sur le bouton
STOP lorsque vous
souhaitez arrêter la
lecture.
CD-R au format JPEG
- Seuls les fichiers portant les extensions “.jpg” ou“.JPG” peuvent être lus.
- Si le disque n’est pas fermé, le démarrage de la lecture sera plus lent et certains des fichiers ne pourront pas être lus.
- Seuls les CD-R comportant des fichiers JPEG au format ISO 9660 ou Joliet peuvent être lus.
- Le nom des fichiers JPEG peut contenir un maximum de huit caractères. Les espaces et les caractères spéciaux (./=+) ne sont
pas autorisés.
- Seul les disques gravés en multisessions consécutives peuvent être lus. Si la lentille de lecture rencontre un segment vierge sur
un disque multisession, la lecture des fichiers s'arrête à ce segment-là.
- Un CD possède une capacité de stockage maximale de 3000 images.
- Nous vous recommandons les CD Kodak Picture.
- Sur les CD photos de Kodak, seuls les fichiers JPEG dans le dossier des images peuvent être lus.
- CD d’images Kodak : Les fichiers JPEG dans le dossier images peuvent être lus automatiquement.
- CD d’images Konica : Si vous souhaitez voir l’image, sélectionnez les fichiers JPEG dans le menu clips.
- CD d’images Fuji : Si vous souhaitez voir l’image, sélectionnez les fichiers JPEG dans le menu clips.
- CD d’images QSS : L’unité ne peut pas lire le CD d’images QSS.
- Si le nombre de fichiers sur le disque “1” dépasse la limite de 500, seuls 500 fichiers JPEG peuvent être lus.
- Si le nombre de dossiers sur le disque “1” dépasse la limite de 500, seuls 500 dossiers JPEG peuvent être lus.
FRA-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapitre 5
CHANGEMENT DU MENU CONFIGURATION
Utilisation du menu de configuration
Ce menu vous permet de personnaliser votre lecteur DVD. Grâce à lui, vous pouvez choisir une
langue parmi les différentes proposées, mettre au point le contrôle parental et même ajuster le
lecteur au format d’écran de votre téléviseur.
Réglage de la langue
Options Audio
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU de la
télécommande.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
DVD-FP580 Setup Menu
Réglage de la langue
Options Audio
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Anynet+(HDMI-CEC): Oui
Enter
Return
Menu
DVD-F1080 Setup Menu
Réglage de la langue : Réglage de la langue.
❶
❷
❸
Options Audio : Configuration des caractéristiques audio.
Options D’affichage : Mise au point des caractéristiques d’affichage. Utilisez ce sousmenu pour
choisir le format de l’écran que vous utilisez et d’autres caractéristiques d’affichage.
Cont. Parental : Configuration du contrôle parental. Cette fonction permet aux utilisateurs de
définir le seuil au-delà duquel ils désirent interdire à leurs enfants de regarder certains films
comprenant des scènes de violence ou réservés aux adultes, etc.
DivX(R) Immatriculation : veuillez utiliser le code d’enregistrement pour enregistrer ce lecteur auprès
du service Vidéo DivX(R) à la demande. Vous pourrez ainsi louer et acheter des vidéos utilisant le
format Vidéo DivX(R) à la demande. Pour de plus amples informations, rendez-vous sur
www.divx.com/vod.
❹
❺
❻
Anynet+(HDMI-CEC) : Configuration des caractéristiques Anynet+(HDMI-CEC) (DVD-F1080
uniquement).
2
Appuyez sur les boutons
/ pour accéder aux
différentes fonctionnalités.
Appuyez sur la touche
ou ENTER pour accéder
aux fonctions plus
détaillées du sous-menu.
3
Pour faire disparaître
l’écran de configuration,
appuyez de nouveau sur
la touche MENU.
Remarque
Certaines sélections que vous opérez dans le
menu de configuration peuvent ne pas
fonctionner avec certains disques.
FRA-42
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Configuration des options de langue
Dans le menu principal du lecteur DVD, après avoir validé, vos choix de langue d’écoute et de
sous-titres, ce choix de langue est automatiquement choisi chaque fois que vous regardez un film.
Choix de la langue du menu du lecteur
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner
Réglage de la langue
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
RÉGLAGE DE LA LANGUE
4
Menus du lecteur
Menus du disque
Audio
:
:
:
:
:
Français
Français
Français
Automatique
Unicode
Utilisez les boutons /
pour sélectionner Menus
du lecteur puis appuyez
sur ou sur ENTER.
Sous-Titre
DivX Sous-Titre
Enter
Return
Menu
- La langue est sélectionnée et l'écran revient
au menu d'installation.
RÉGLAGE DE LA LANGUE
5
M
e
n
u
s
d
u
le
c
English
Appuyez sur les boutons
/ pour sélectionner la
langue souhaitée, puis
appuyez sur le bouton
ou sur ENTER.
- Pour faire disparaître le menu de
configuration, appuyez sur le bouton MENU.
√ Français
Deutsch
Español
Menus du dis
Audio
Sous-Titre
DivX Sous-Tit
Italiano
Nederlands
Return
Menu
Enter
FRA-43
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Choix de la langue du menu du disque
Cette fonction ne modifie que la langue d’affichage sur les menus du disque.
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner
Réglage de la langue
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
RÉGLAGE DE LA LANGUE
4
Menus du lecteur
Menus du disque
Audio
:
:
:
:
:
Français
Français
Français
Automatique
Unicode
Utilisez les boutons /
pour sélectionner Menus
du disque puis appuyez
sur ou sur ENTER.
Sous-Titre
DivX Sous-Titre
Enter
Return
Menu
- Si la langue sélectionnée n’est pas
enregistrée sur le disque, le système
sélectionne la langue d’origine
préenregistrée.
RÉGLAGE DE LA LANGUE
5
Menus du lec
Menus du dis
Audio
English
√ Français
Deutsch
Español
Italiano
Appuyez sur les boutons
/ pour sélectionner la
langue souhaitée, puis
appuyez sur le bouton
ou sur ENTER.
- La langue est sélectionnée et l'écran revient
au menu d'installation.
Sous-Titre
DivX Sous-Tit
Nederlands
- Pour faire disparaître le menu de
Enter
Return
Menu
configuration, appuyez sur le bouton MENU.
FRA-44
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Choix de la langue de la bande sonore
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner
Réglage de la langue
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
RÉGLAGE DE LA LANGUE
4
Menus du lecteur
Menus du disque
Audio
:
:
:
:
:
Français
Français
Français
Automatique
Unicode
Utilisez les boutons /
pour sélectionner Audio
puis appuyez sur ou
sur ENTER.
Sous-Titre
DivX Sous-Titre
Enter
Return
Menu
- Choisissez “Originale” si vous voulez que la
bande son soit dans la langue originale.
RÉGLAGE DE LA LANGUE
5
- Si la langue sélectionnée n’est pas
enregistrée sur le disque, le système
sélectionne la langue d’origine préenregistrée.
Menus du lec
Menus du dis
Audio
Originale
English
√ Français
Deutsch
Español
Italiano
Appuyez sur les boutons
/ pour sélectionner la
langue souhaitée, puis
appuyez sur le bouton
ou sur ENTER.
Sous-Titre
DivX Sous-Tit
- La langue est sélectionnée et l'écran revient
au menu d'installation.
Enter
Return
Menu
- Pour faire disparaître le menu de
configuration, appuyez sur le bouton MENU.
FRA-45
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Choix de la langue des sous-titres
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner
Réglage de la langue
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
RÉGLAGE DE LA LANGUE
4
Menus du lecteur
Menus du disque
Audio
:
:
:
:
:
Français
Français
Français
Automatique
Unicode
Utilisez les boutons /
pour sélectionner Sous-
Titre puis appuyez sur
ou sur ENTER.
Sous-Titre
DivX Sous-Titre
Enter
Return
Menu
- Sélectionnez “Automatique” si vous souhaitez
que la langue des sous-titres soit identique à
celle sélectionnée pour la langue audio.
RÉGLAGE DE LA LANGUE
5
Menus du lec
Menus du dis
Audio
√ Automatique
English
Français
Deutsch
Español
Appuyez sur les boutons
/ pour sélectionner la
langue souhaitée, puis
appuyez sur le bouton
ou sur ENTER.
- Sur certains disques, la langue que vous
choisissez peut ne pas exister. Dans ce cas,
les sous-titres apparaîtront dans l’une des
langues prioritaires.
Sous-Titre
DivX Sous-Tit
Italiano
Enter
Return
Menu
- Si la langue sélectionnée n’est pas
enregistrée sur le disque, le système
sélectionne la langue d’origine préenregistrée.
- La langue est sélectionnée et l'écran revient
au menu d'installation.
- Pour faire disparaître le menu de
configuration, appuyez sur le bouton MENU.
FRA-46
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Choix de la langue des DivX sous-titres
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Anynet+(HDMI-CEC): Oui
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner
Réglage de la langue
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Anynet+(HDMI-CEC): Oui
Enter
Return
Menu
RÉGLAGE DE LA LANGUE
4
Menus du lecteur
Menus du disque
Audio
:
:
:
:
:
Français
Français
Français
Automatique
Unicode
Utilisez les boutons /
pour sélectionner DivX
Sous-Titre puis appuyez
sur ou sur ENTER.
Sous-Titre
DivX Sous-Titre
Enter
Return
Menu
- La langue est sélectionnée et l'écran revient
au menu d'installation.
RÉGLAGE DE LA LANGUE
5
Menus du lecteur
Menus du disque
:
:
Français
Français
- Pour faire disparaître le menu de
configuration, appuyez sur le bouton MENU.
Appuyez sur les boutons
/ pour sélectionner la
langue souhaitée, puis
appuyez sur le bouton
ou sur ENTER.
Audio
√ Unicode
Western
Turkish
Central
Cyrillic
Greek
Sous-Titre
DivX Sous-Tit
Enter
Return
Menu
FRA-47
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Configuration des options audio
Les options audio vous permettent de configurer le dispositif audio et les paramètres
relatifs au son en fonction du système audio utilisé.
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Options
Audio puis appuyez sur
ou sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
Pour faire disparaître le menu de configuration,
appuyez sur le bouton MENU.
OPTIONS AUDIO
4
Sortie Digital
:
:
:
:
PCM
PCM
Oui
Appuyez sur les boutons
/ pour sélectionner
l'élément souhaité, puis
appuyez sur le bouton
ou ENTER.
MPEG-2 Digital
Compression Dynamique
Echantillonnage PCM
Oui
Enter
Return
Menu
FRA-48
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
❶
Sortie Digital
- PCM : Conversion en audio PCM(2CH).
- Bitstream : Emet un son Dolby Digital via la sortie numérique.
Sélectionnez Bitstream lors de la connexion au décodeur Dolby Digital.
❷
MPEG-2 Digital
- PCM : Conversion en audio PCM(2CH).
- Bitstream : Conversion en Bitstream MPEG-2 Digital (5.1CH ou 8CH). Sélectionnez Bitstream
lorsque vous utilisez la sortie audio numérique.
❸
❹
Compression Dynamique
- Oui : Pour sélectionner la compression dynamique.
- Non : Pour sélectionner la gamme standard.
Echantillonnage PCM
- Oui : Sélectionnez cette option lorsque l’amplificateur relié au lecteur ne supporte pas une
fréquence de 96 KHz. Dans ce cas, les signaux de 96 KHz sont convertis en signaux de
48 KHz.
- Non : Sélectionnez cette option lorsque l’amplificateur relié au lecteur supporte une fréquence
de 96 KHz. Dans ce cas, tous les signaux sont transmis sans aucune modification.
Remarque
Même si l’échantillonnage bas PCM est Non,
• Certains disques ne peuvent émettre un signal audio à échantillonnage bas que via les sorties
numériques.
HDMI (DVD-F1080 uniquement)
- Si votre TV n'est pas compatible avec des formats multicanaux non compressés (Dolby
Digital, DTS, MPEG), vous devez paramétrer Audio sur PCM.
- Si votre TV n'est pas compatible avec le taux d'échantillonnage LPCM supérieur à 48kHz,
vous devez choisir un taux d'échantillonnage PCM inférieur.
Remarque
• Pour faire disparaître le menu de configuration, appuyez sur le bouton MENU.
• Il n'y a pas de sortie audio analogique lorsque vous lisez un disque DTS.
Fabriqué en vertu d’une licence accordée par les Laboratories Dolby. “Dolby” et le symbole du
double D sont des marques déposées de Dolby Laboratories.
“DTS” et “DTS Digital Out” sont des marques déposées de Digital Theater Systems, Inc.
FRA-49
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Configuration des options d’affichage
Les options d'affichage vous permettent de régler les différentes fonctions vidéo du
lecteur.
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Options
D'affichage puis appuyez
sur ou sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
Pour faire disparaître le menu de configuration,
appuyez sur le bouton MENU.
OPTIONS D’AFFICHAGE
4
Format écran
:Large
Appuyez sur les boutons
/ pour sélectionner
l'élément souhaité, puis
appuyez sur le bouton
ou ENTER.
Mode arrêt sur image :Auto
Messages écran
Sortie Vidéo
:Oui
:P-SCAN
: Non
Niveau des Noirs
Enter
Return
Menu
DVD-FP580
OPTIONS D’AFFICHAGE
OPTIONS D’AFFICHAGE
Format écran
:Large
Mode arrêt sur image :Auto
Messages écran
Sortie Vidéo
HDMI
:Oui
:P-SCAN
Qualité image
Enter
Return
Menu
DVD-F1080
OPTIONS D’AFFICHAGE
FRA-50
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Format Écran
Selon le type de téléviseur, vous pouvez
régler votre écran (réglage d’aspect).
• Si vous appuyez sur la touche VIDEO SEL
tandis que le lecteur DVD est en mode de
lecture, arrêt, ou qu'aucun disque n'est
présent. Le mode de sortie vidéo s’affiche
selon la séquence suivante :
❶
- 4:3 Letter Box : Sélectionnez cette option
lorsque vous voulez visionner le DVD en
mode 16/9 alors que vous avez un
téléviseur 4/3. Des barres noires
apparaîtront en haut et en bas de l’écran.
- 4:3 Pan&Scan : Lorsque l’écran de votre
téléviseur est de format classique,
sélectionnez cette option. Si vous voulez
regarder la partie centrale de l’écran 16/9,
les parties droite et gauche de l’image
seront recadrées.
( I-SCAN ➝ P-SCAN)
❺ HDMI
Ce réglage est disponible lorsque l’appareil
connecté aux dispositifs d’affichage (TV,
projecteur, etc.) par HDMI.
- Résolution Setting
- Auto : Permet de régler la résolution
automatiquement.
- Manual : Permet de régler la résolution
Manuellement.
- Résolution
- 16:9 Large : Le téléviseur au format 16/9
assure une répartition optimale sur l’écran.
OPTIONS D’AFFICHAGE
Format écran
- 480p : 720 x 480
- 720p : 1280 x 720
- 1080i : 1920 x 1080
- 1080p : 1920 x 1080
4:3 Letter Box
Mode arrêt sur im
Messages écran
Sortie Vidéo
4:3 Pan&Scan
√ 16:9 Large
: I-SCAN
Niveau des Noirs
: Non
Enter
Return
Menu
OPTIONS D’AFFICHAGE
Format écran
:Large
❷ Mode arrêt sur Image
Mode arrêt sur image :Auto
Ces options permettent de stabiliser l’image
en mode arrêt sur image pour un affichage
optimal des textes.
Messages écran
Sortie Vidéo
HDMI
:Oui
:P-SCAN
Qualité image
- Auto : Si vous sélectionnez Auto, l’appareil
gère au mieux la qualité de l’image.
Enter
Return
Menu
- Trame : Sélectionnez cette option lorsque
les images tremblent en mode Auto.
- Vue : Sélectionnez cette option lorsque
vous voulez mieux voir les petits caractères
qu’en mode Auto.
OPTION HDMI
Résolution Setting : Manual
Résolution : 720p
❸ Messages Écran
Enter
Return
Menu
Utilisez cette fonction pour activer ou supprimer
l'affichage des messages à l’écran.
Si votre téléviseur ne peut accueillir la
résolution désirée, il peut afficher le
message d'avertissement suivant et la
résolution revient à son réglage précédent.
❹ Sortie Vidéo
Sélectionnez la sortie vidéo.
- I-SCAN : A sélectionner lorsque vous
souhaitez utiliser la sortie Vidéo et
Component 525i(Interlace).
OPTION HDMI
- P-SCAN : A sélectionner lorsque vous
souhaitez utiliser la sortie Component 525p
(Progressive) ou HDMI.
Le téléviseur ne peut
accueillir cette résolution
Enter
Return
Menu
FRA-51
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
❻
Qualité Image / Options D'affichage
- Niveau des noirs (DVD-FP580 et DVD-
F1080) : ajuste la luminosité de l’écran Oui
(Activé) ou NON (Désactivé). Ne fonctionne
pas en mode Balayage progressif.
• Affichage en mode Balayage progressif
Reportez-vous au manuel d’utilisation de
votre téléviseur pour vérifier si celui-ci
prend en charge le balayage progressif.
Si tel est le cas, suivez les instructions du
manuel d’utilisation du téléviseur
relatives aux réglages du balayage
progressif dans les menus du téléviseur.
• Si la sortie Vidéo n’est pas correctement
réglée, l’écran peut être bloqué.
- Luminosite : Niveau ~ Niveau 5
- Contrast : Niveau ~ Niveau 5
- Saturation des couleurs : Niveau 1 ~ Niveau 5
OPTIONS D’AFFICHAGE
Format écran
:Large
• Les résolutions disponibles pour les
sorties HDMI varient selon la TV ou le
projecteur connecté(e). Pour plus de
détails, référez-vous au manuel de votre
TV ou projecteur (DVD-F1080
Mode arrêt sur image :Auto
Messages écran
Sortie Vidéo
:Oui
:I-SCAN
: Non
Niveau des Noirs
Enter
Return
Menu
DVD-FP580
OPTIONS D’AFFICHAGE
uniquement).
• Lorsque la résolution change pendant la
lecture, quelques secondes peuvent
s’écouler avant que l’image n’apparaisse.
• Vous obtiendrez une meilleure qualité
d’image si vous réglez la résolution de
sortie HDMI à 720p,1080p ou 1080i (DVD-
F1080 uniquement).
QUALITÉ IMAGE
Niveau des Noirs
Luminosite
: Non
: Niveau 3
: Niveau 3
: Niveau 3
Contrast
Satur. couleurs
Enter
Return
Menu
DVD-F1080
QUALITÉ IMAGE
FRA-52
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Configuration du contrôle parental
Le contrôle parental fonctionne avec certains DVD sur lesquels le niveau de contrôle est enregistré. Cela
vous permet de contrôler les DVD que votre famille regarde. Huit niveaux différents sont disponibles.
Paramétrage du niveau de contrôle
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Cont.
Parental puis appuyez sur
ou sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
CONTROLE PARENTAL
4
Niveau de Contrôle : Tout Public
Modif. Code Secret
Utilisez les boutons /
pour sélectionner Niveau
de Contrôle puis appuyez
sur ou sur ENTER.
Setup
Return
Menu
Enter
CONTROLE PARENTAL
5
Niveau de Contrôle
Modif. Code Secret
:
Tout Public
Composez un code secret.
Par défault, le mot de
passe est réglé sur 0000.
Veuillez changer le mot de
passe 0000 pour activer la
fonction du filtrage parental.
Entrer Code Secret
Enter
Return
Menu
Pour faire disparaître le menu de configuration,
appuyez sur le bouton MENU.
CONTROLE PARENTAL
6
Niveau de Contrôl
Rtv
√ Tout Public
Appuyez sur les boutons
/ pour sélectionner le
Niveau de contrôle
souhaité puis appuyez sur
le bouton ou ENTER.
Ex) Configuration du Tout
Public.
En exemple, si vous choisissez niveau 6, les
niveaux 7 et 8 ne seront pas lus.
Modif. Code Secre
Niveau 2
Niveau 3
Niveau 4
Niveau 5
Niveau 6
Enter
Return
Menu
FRA-53
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Changement du mot de passe
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Cont.
Parental puis appuyez sur
ou sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Anynet+(HDMI-CEC): Oui
Enter
Return
Menu
Pour faire disparaître le menu de configuration,
appuyez sur le bouton MENU.
CONTROLE PARENTAL
4
Niveau de Contrôle : Tout Public
Modif. Code Secret
Utilisez les boutons /
pour sélectionner Modif.
Code Secret puis
appuyez sur ou sur
ENTER.
Saisissez votre nouveau
mot de passe.
Enter
Return
Menu
Réintroduisez le nouveau
mot de passe.
CONTROLE PARENTAL
Niveau de Contrôle : Tout Public
Modif. Code Secret
Entrer Code Secret
Enter
Return
Menu
CONTROLE PARENTAL
Niveau de Contrôle
Modif. Code Secret
:
Tout Public
Entrer le nouveau Code Secret
Remarque
Si vous avez oublié votre mot de passe, reportez-vous
à la rubrique “Mot de passe oublié” dans le Guide de
dépannage (Problèmes et solutions).
Enter
Return
Menu
FRA-54
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGEMENT DU MENU CONFIGURATION
Réglage de l’option Anynet+ (HDMI CEC)
(DVD-F1080 uniquement)
Anynet+ est une option utilisée pour contrôler l’appareil à l’aide d’une télécommande de
téléviseur SAMSUNG, en raccordant le lecteur DVD-F1080 à un téléviseur SAMSUNG à l’aide
d’un câble HDMI. (Voir les pages 12 et 13) Ce mode n’est disponible qu’avec les téléviseurs
Samsung pouvant accueillir Anynet+).
Sélectionnez On (Activée) lorsque le DVD-F1080 est raccordé à un téléviseur Samsung
pouvant accueillir l’option Anynet+.
1
L’unité étant en mode
Stop (arrêt), appuyez sur
la touche MENU.
2
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner Setup
puis appuyez sur ou
sur ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Anynet+(HDMI-CEC): Oui
Enter
Return
Menu
3
Réglage de la langue
Options Audio
Utilisez les boutons /
pour sélectionner
Anynet+(HDMI-CEC) puis
appuyez sur ou sur
ENTER.
Options D'affichage
Cont. Parental :
DivX(R) Immatriculation
Anynet+(HDMI-CEC): Oui
Enter
Return
Menu
Pour faire disparaître le menu de configuration,
appuyez sur le bouton MENU
4
Réglage de la langue
Options Audio
.
Réglez l’option Anynet+
(HDMI-CEC) de votre
lecteur DVD à “On” puis
Options D'affichage
Cont. Parental :
DivX(R) Immatculation
Non
appuyez sur la touche
ou sur ENTER.
√
Oui
Anynet+(HDMI
Enter
Return
Menu
FRA-55
Download from Www.Somanuals.com. All Manuals Search And Download.
5
DVDP
View TV
®
®
®
®
Réglez l'option Anynet+ sur
votre téléviseur. (Reportez-
vous au manuel de l’usager
de votre téléviseur pour plus
de détails.)
Select Device
Record
Menu on Device
Device Operation
®
®
®
Receiver
Setup
:
Off
ENTER
Move
Exit
• Lorsque vous appuyez sur
la touche Anynet+ de la
télécommande de votre
téléviseur, l’affichage situé
en bas apparaît.
TV Menu
La télécommande du téléviseur vous permet d’exploiter le lecteur DVD. (Touches du téléviseur
utilisées pour contrôler le lecteur DVD :
,
,
,
,
,
,
et
touches,
touches.
- Select Device (Sélectionnez l’appareil) : : Utilisez cette option pour sélectionner un
appareil.
- Menu on Device (Menu de l’appareil) : Même résultat avec la touche MENU de la
télécommande du lecteur DVD
- Device Operation (Fonctionnement de l’appareil) : Même résultat avec la touche INFO de
la télécommande du lecteur DVD.
Remarque
• En appuyant sur la touche PLAY de l’appareil tout en regardant la télévision, l’écran
passe en mode de lecture.
• Si vous lisez un DVD alors que le téléviseur est éteint, ce dernier s’allume,
• Si vous éteignez le téléviseur, le lecteur DVD s’éteint automatiquement.
• Si vous passez de HDMI à une autre source (Composite, Composantes, …etc.) de votre
téléviseur en cours de lecture d’un DVD, le lecteur DVD s’arrête.
FRA-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapitre 6
FICHE TECHNIQUE
2. Appuyez sur les boutons ¦ꢀ pour sélectionner Total,
puis appuyez sur le bouton ENTER.
Mise à jour du
micrologiciel
Introduction
Samsung prend souvent en charge la mise à
jour du logiciel afin d’accroître les
performances de l’appareil et d’apporter les
dernières modifications, via son site Internet
(www.samsung.com/ca).
La mise à jour du micrologiciel démarre
En effet, un nouveau codec mpeg4 a été mis
au point et est sujet à des améliorations
constantes. Les améliorations apportées
dépendent de la mise à jour du logiciel que
vous utilisez ainsi que du logiciel fourni avec
votre lecteur DVD avant cette mise à jour.
- Le tiroir s’ouvre automatiquement pendant l’écriture.
Attendez 2 minutes après avoir retiré le disque.
- Lorsque la mise à jour est réussie, le lecteur s’éteint et
se remet en marche après la
fermeture automatique du tiroir.
3. Appuyez sur les touches numériques pour sélectionner la
langue souhaitée.
Comment créer un disque de
mise à jour
1. Vous devez télécharger un nouveau fichier depuis le centre
téléchargement Samsung disponible sur Internet
(www.samsung.com/ca).
2. Enregistrez le fichier sur votre ordinateur en utilisant un CD-
RW.
Remarque
-
-
-
-
Système de fichiers niveau CD-ROM ISO
Configuration des caractères ISO 9660
Dernière mise au point, session unique
Vitesse d’écriture lente
Remarque
-
Veuillez contacter votre “Centre de service technique
Samsung” si le message “Sélectionnez une langue de
menu” ne s’affiche pas.
-
-
N’appuyez sur aucun bouton ni ne débranchez pas le
cordon d’alimentation pendant la mise à jour.
La procédure de mise à jour peut varier,
Procédure de mise à jour
reportez-vous au site Web (www.samsung.com/ca).
1. Ouvrez le tiroir disque. Placez le disque dans le tiroir.
Fermez le tiroir. L’écran de mise à jour du micrologiciel
apparaît.
La mise à jour du micrologiciel
s’affiche
FRA-57
Download from Www.Somanuals.com. All Manuals Search And Download.
FICHE TECHNIQUE
Problèmes et solutions
Avant de demander une assistance auprès de votre revendeur ou d’un service après vente, veuillez
vérifier les points suivants.
Résolution
Problèmes
Page
• Vérifiez les piles de la télécommande.
Changez-les au besoin.
La télécommande ne
fonctionne pas.
• Utilisez la télécommande à une distance inférieure à 6 mètres.
• Retirez les piles et maintenez une ou plusieurs touches pendant quelques
minutes pour réinitialiser le microprocesseur dans la télécommande. Remettez
les piles et essayez de nouveau.
P5
P8
La lecture du disque e
se fait pas.
• Vérifiez l’installation du disque : étiquette sur le dessus.
• Vérifiez le numéro de région du DVD.
• Le son du canal 5.1 ne s’entend que dans les conditions suivantes :
1) Le lecteur de DVD est correctement raccordé à un amplificateur 5.1.
2) Le disque est enregistré avec un son 5.1.
Aucun son avec le
canal 5.1
P18
• Vérifiez si le disque porte la mention "Dolby ou DTS 5.1 ch"
• Vérifiez si votre système audio est branché et fonctionne correctement.
P48~49
•
Dans le menu CONFIGURATION, la sortie audio est-elle réglée sur Bitstream ?
• Impossible de terminer les options ou l’action en cours car :
1. Le logiciel du DVD s’y oppose.
2. Le logiciel du DVD n’accepte pas cette option (ex : pas de multi-angles)
3. L’option n’est pas disponible à cet instant.
L’icône
sur l’écran.
s’affiche
4. Vous avez demandé un titre ou un chapitre ou cherché une durée, ne
correspondant pas aux données.
Le Menu disque nes’affiche pas.
• Vérifiez si le disque possède un Menu.
Le mode Lecture est
différent de la sélection
du Menu installation.
• Certaines fonctions sélectionnées dans le Menu installation peuvent ne pas
fonctionner correctement si le code du disque ne correspond pas à la fonction.
P42~56
Le rapport d’écran ne
peut être modifié.
• Le format d’écran est fixé en fonction de son enregistrement sur le DVD.
P50~52
P48~49
• Vérifiez si la sélection Sortie numérique dans le Menu options audio est
correcte.
Aucun son.
L’écran est bloqué.
• Appuyez sur le bouton
(Sur le panneau avant) pendant plus de 5 secondes
P19
P53
en l'absence de disque. Tous les réglages sont réinitialisés sur les valeurs usine.
• Appuyez sur le bouton
en l'absence de disque. Tous les réglages y compris le mot de passe sont
réinitialisés sur les valeurs usine. Ne l'utilisez qu'en cas d'absolue nécessité.
(Sur le panneau avant) pendant plus de 5 secondes
Mot de passe oublié.
Autres problèmes.
• Dans le manuel d’instructions, recherchez la section contenant les
explications du problème rencontré et suivez de nouveau le processus.
• Si le problème n’est pas résolu, veuillez contacter votre revendeur ou le
service après-vente agréé le plus proche.
• Assurez-vous que le disque ne soit pas sale ou rayé.
• Nettoyez le disque.
L'image est brouillée
ou déformée.
P4
FRA-58
Download from Www.Somanuals.com. All Manuals Search And Download.
FICHE TECHNIQUE
Résolution
Problèmes
Page
P12~13
P12~13
Pas de sortie HDMI
(DVD-F1080 only).
• Vérifiez la sortie vidéo et activez le mode HDMI.
• Vérifiez la connexion entre le téléviseur et le lecteur DVD.
• Vérifiez si le téléviseur est compatible au lecteur DVD 480p/720p/1080i/1080p.
• S’il y a un bruit de neige à l’écran, cela veut dire que le téléviseur n’est pas
compatible au HDCP (High-bandwidth Digital Content Protection).
Écran HDMII anormal
(DVD-F1080 only).
Vibrations de la sortie
HDMI
(DVD-F1080 only).
• Vérifiez que l'installation de votre téléviseur est correcte.
• Le phénomène de vibrations de l'écran peut se produire lorsque la fréquence
de l'image passe de 50Hz à 60Hz pour une sortie 720P/1080i/1080p HDMI
(Interface Multimédia Haute Définition).
P50~52
• Référez-vous au manuel de l’utilisateur de votre TV.
FRA-59
Download from Www.Somanuals.com. All Manuals Search And Download.
FICHE TECHNIQUE
Spécifications
Alimentation
Consommation électrique
Poids
AC 120V, ~ 60 Hz
7 W
0.976 Kg
Général
Disque
Dimensions
240mm (W) X 240mm (D) X 50.5mm (H)
+5°C to +35°C
Température de fonctionnement
Humidité ambiante
10 % to 75 %
Vitesse de lecture : 11,45 ~ 15,09 pi/sec.
Durée approximative de lecture
DVD
(DIGITAL VERSATILE DISC)
(Disque mono face, Disque mono couche) : 135 min.
Vitesse de lecture : 15,75 ~ 18,37 pi/sec.
Durée maximale de lecture : 74 min.
Vitesse de lecture : 15,75 ~ 18,37 pi/sec.
Durée maximale de lecture : 20 min.
CD : 5"
(Disque compact)
CD : 31/2"
(Disque compact)
Vidéo composite
1 canaux : 1,0 Vcc (impédance de75 Ω)
Y : 1,0 Vcc (impédance de 75 Ω)
Pr : 0,70 Vcc (impédance de 75 Ω)
Pb : 0,70 Vcc (impédance de 75 Ω)
Sortie
Vidéo
Vidéo Composant
HDMI
480p, 720p, 1080i, 1080p (DVD-F1080 uniquement)
2
CANAUX
G (1/G), D (2/D)
4 Hz à 22 kHz (échantillonnage à 48 kHz)
*RÉPONSE EN FRÉQUENCE
4 Hz à 44 kHz (échantillonnage à 96 kHz)
Sortie
Audio
*RAPPORT SIGNAL/BRUIT
*LIMITES DYNAMIQUES
110 dB
100 dB
0.004 %
*DISTORSION HARMONIQUE TOTALE
*: Spécifications nominales
- Samsung Electronics Co., Ltd se réserve le droit de modifier les spécifications
sans préavis.
- Les poids et dimensions sont approximatifs.
FRA-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Contactez SAMSUNG WORLD WIDE
Si vous avez des commentaires our des questions concernant les produits Samsung, contactez le centre
de service à la clientèle SAMSUNG.
Download from Www.Somanuals.com. All Manuals Search And Download.
GARANTIE LIMITÉE À L’ACHETEUR INITIAL
Samsung Electronics Canada Inc. (SECA) garantit ce produit contre tout défaut de fabrication.
SECA garantit aussi que si cet appareil ne fonctionne pas convenablement durant la période de garantie SECA se
réservera le droit de réparer ou de remplacer l’appareil défectueux. Toutes les réparations sous garantie doivent être
effectuées par un Centre de service autorisé SECA.
Le nom et l’adresse du Centre de service le plus près de chez vous peut être obtenu en composant sans frais le
1-800-268-1620 ou en visitant notre site web au www.samsung.ca
Main-d’oeuvre
Pièces
un (1) an (au comptoir)
un (1) an
Pour tous les modèles portatifs, le transport de l’appareil sera la responsabilité du client.
Le reçu de vente original doit être conservé par le client car cela constitue la seule preuve d’achat acceptée.
Le client doit le présenter au Centre de service agréé au moment où il fait la demande d’une réparation sous garantie.
EXCLUSIONS (CE QUI N’EST PAS COUVERT)
Cette garantie ne couvre pas les dommages causés par un accident, un incendie, une inondation, un cas de force
majeure, un mauvais usage ou une tension incorrecte. La garantie ne couvre pas une mauvaise installation, une
mauvaise réparation, une réparation non autorisée et tout usage commercial ou dommages survenus durant le
transport. Le fini extérieur et intérieur de même que les lampes ne sont pas couverts par cette garantie.
Les ajustements par le client qui sont expliqués dans le guide de l’utilisateur ne sont pas couverts en vertu de cette
garantie. Cette garantie sera automatiquement annulée pour tout appareil qui aurait un numéro de série manquant ou
modifié. Cette garantie est valable seulement sur les appareils achetés et utilisés au Canada.
Samsung Electronique Canada Inc.,
Service à la Clientèle
55 Standish Court
Mississauga, Ontario L5R 4B2
Canada
1-800-SAMSUNG (7267864)
www.samsung.com/ca
Download from Www.Somanuals.com. All Manuals Search And Download.
|