DSR 9401 FTA / DSB-9401F / DSB-9401V
Instructions for use
GB
DIGITAL SATELLITE RECEIVER
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENT
GENERAL FEATURES
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connecting Your STB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Basic Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operating The Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1 LNB Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.2 Positioner Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.2.1 User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.2.2 Installer Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.3 Solarsat Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
1.4 Auto Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.5 Manual Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.6 SMATV Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.7 Reset to Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2. Channel Organising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.1 Delete Satellite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.2 Delete Transponder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2.3 Delete Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.4 Delete All Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.5 Delete Scrambled Channels . . . . . . . . . . . . . . . . . . . . . . . . 22
2.6 Favorite Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.7 Move & Edit Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3. Parental Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.1 Set Channel Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.2 Change PIN Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4. System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.1 Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.2 OSD Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3 Media Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.4 Time &Timer Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4.5 System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.6 Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1. USER SECTION
4000 PROGRAMMABLE CHANNELS
SOFTWARE DOWNLOAD VIA SATELLITE & PC
ADVANCED ELECTRONIC PROGRAM GUIDE
MULTI LANGUAGE SUPPORTED FOR OSD
SUBTITLE & TELETEXT(OSD & VBI)SUPPORTED
WITH MULTI LANGUAGE
DiSEqC 1.2 SUPPORTED
FULL FUNCTION INFRARED REMOTE CONTROL UNIT
AUTO AND MANUAL SCAN FACILITY
CHANNEL ORGANIZING (PROGRAMMABLE)
SCARTS OUTPUT (Optional)
LOW POWER CONSUMPTION
9 FAVORITE LISTS
AUTO UPDATED EPG
2. TUNER SECTION
3. VIDEO SECTION
950~2150 MHz WIDE BAND TUNER
SUPPORTING DiSEqC 1.2 VERSION
13V/18V SWITCHING
22KHz CONTINUOUS TONE CONTROL
DVB-S COMPLIANT
MPEG-2 VIDEO(MP@ML)
2~45 MS/s SYMBOL RATE
COMPATIBLE FOR BOTH SCPC/MCPC
SUPPORTS ASPECT RATIO 4:3(NORMAL) AND
16:9(WIDE SCREEN)
4. AUDIO SECTION
MPEG 1 AUDIO LAYER I & II
MONO, DUAL, STEREO AND JOINT STEREO AUDIO MODE
32, 44.1 AND 48 kHz SAMPLING FREQUENCIES
VOLUME CONTROL AND MUTE FUNCTION THROUGH
REMOTE CONTROL UNIT
5. Embedded Viaccess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
SPDIF DIGITAL AUDIO OUTPUT
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-2
GB-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTINGYOUR "STB"
CONNECTING YOUR "STB"
1. LOCATION OF THE RECEIVER
Connecting Figure
Your STB should be placed under proper ventilation.
Don’t put in completely enclosed cabinet that will restrict the flow of air,
resulting in overheating.
The location should be safeguarded from direct sunlight,
excess moisture, rough handling or household pets.
Avoid stacking other electronic components on the top of the receiver.
The location should be safely accessible by the cable from your
antenna system.
2. CONNECTING THE RECEIVER WITH DISH SYSTEM
After installing your antenna system, connect the coaxial cable from the
LNB of your antenna to "LNB" terminal marked at the rear
of the STB
.
All cable connectors should be finger tightened; do not use any kind
of wrench while tightenning connectors. The cable should be 75ohm
impedance coaxial twisted at the end with an "F" type connector.
3. CONNECTING THE RECEIVER TO TV
To connect the receiver with your television, you can use Scart Cable.
In the case of connecting your TV through SCART cable, connect the
SCART connector marked TV to the respective SCART port on the TV.
4. CONNECTING YOUR VCR
To connect a VCR, the STB has been provided with SCART at the rear
marked "VCR".
Using a SCART connector, the VCR can be connected to the receiver.
Note : This is supported by standby.
5. CONNECTING YOUR DIGITAL AUDIO SYSTEM
If you have a DAC with S/PDIF optical cable input, you can connect the STB
with it to enjoy higher quality sound. Connect S/PDIF optical cable to a digital
amplifier.
6. INSERTING SMARTCARDS FOR VIACCESS SERVICES
(For model DSB-9401V)
In order to view a scrambled service, you need to have a valid Smartcard.
This DSB-9401V has the Viaccess CAS embedded to view Viaccess programmes.
Note : Insert the Smartcard with the gold coloured chip facing downwards.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-4
GB-5
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
DESCRIPTION
Front Panel
Rear Panel
1
2
4
3
2
1
1. AC MAINS
This is to plug in the AC mains power cord.
The input AC voltage range is 100V to 240V, 50Hz/60Hz supply.
1. LED Display
2. Card Slot
When the LED light Red, the set-top box enters the
standby mode.
When the LED light Green, it enters the operation mode.
2. S/PDIF
Output for connection to a digital amplifier.
This is used to connect to your VCR.
This is used to connect to your TV.
1 Slot for Viaccess smartcard. (For model DSB-9401V)
3. VCR SCART
4. TV SCART
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-6
GB-7
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
DESCRIPTION
5. MUTE
6. FAV
This key is used to toggle between normal & muted audio.
Use the key to switch between favorite lists.
Remote Control Unit
7. EPG
Electronic Program Guide button displays the TV/Radio Program
guide.
8. LAST
This key is used to call up directly whatever channel you were
watching list.
9. TEXT(GREEN)
This key is used to select the subtitle mode.
(
)
This button functions same as the GREEN button on the menu.
Press once and subtitle appears. You can select the language you
want using the channel +/- keys.
Press twice and Teletext with OSD appears.
Press three times and Teletext with VBI appears.
10. ALT(YELLOW)
This key is used to select the soundtrack list for the current service.
This button functions same as the YELLOW button on the menu.
Press once and sound track appears.
(
)
Press twice and video track appears.
The sound and video track services are not provided for every
channel and depend on the conditions the operator is in.
11. AUDIO(BLUE)
This key is used to change the Audio to the left, right or both
channels.
(
)
This button functions same as the BLUE button on the menu.
12. INFORMATION This key is used to display the programe information box in the screen.
(RED)
(
)
This button functions same as the RED button on the menu. Press once
and you can get simple information on the program. Press twice and
you can get detailed information on the channel in text box.
13. MENU
14. EXIT
15. OK(
This key is used to open up the menu or return to the previous menu.
This key is used to exit a menu or return to the previous menu.
Note : When inserting batteries, make sure that the polarity(+/-) is correct.
)
This key is used to enter and confirm any data to the receiver in the
menu system. This key is used to select the item. Press while viewing
TV and a list of channels is displayed.
1. POWER(
)
This is used to switch the receiver ON/STANDBY mode.
16.
,
,
These keys are used to move the highlight bar for selecting
options on the menu, and this button is used to change channels
and increase or decrease the volume.
2. 0-9 Numerical keys (
~
)
(
)
These keys are to enter numeric values and to select the channel
directly by entering its number.
17. CH+/CH-(
18. VOL+/VOL-
)
These keys are used to change channels.
3. Pg+/Pg-
(
,
)
These keys are used to move up or down pages the menu.
These keys are used to increase or decrease the volume.
These keys are used to move up or down pages
on the channel list.
4. TV/RADIO
This key is used to toggle between the TV channel and Radio
channel.
(
)
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-8
GB-9
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTION
BASIC FUNCTIONS
3. Select Soundtrack
1. Display Screen
Before you can view the television program, you must perform the installation.
Therefore you will see only menu images at first.
● Press Yellow (
) key to see
the soundtrack list.
After the television channels have been programmed, you will see the following
picture(banner) each time you switch channels:
● Press
/
and
key to select one.
Left Audio Status
Parental Lock
Channel Number
Channel Name
Right Audio Status
CAS Name
4. Select Videotrack
● Press Yellow (
) key twice to see
Signal Status
Program Information
Current Favorite
The number of soundtrack in current channel
the videotrack list.
● Press
/
and
key to select one.
● Press the Red (
● Select the channel by pressing Numerical (
keys and select TV/RADIO key to move to TV or
) key in view mode.
~
) keys or
/
Radio channel.
You will also see this picture each time you change channels.
When you press TV/RADIO key on the Remote Control Unit,
TV and Radio program are toggled.
5. Service List
● Press
● Select list by pressing TV/RADIO or FAV key.
The icon behind the channel name
symbolises scrambled channel, and
the icon behind the channel name
key to while you are viewing a program.
Detailed program information
● Press the Red (
) key twice while you are viewing a program.
First you will see the banner described above.
symbolises lock channel.
After pressing the Red (
) key a second time you will receive detailed
program information.
● Select the channel by pressing
/
,
/
.
● Press
key to watch that channel.
Note : This service depends on service provider.
2. Volume Control
The colour key corresponds the following service list.
● Green
(
) key : Favorites
) key : Alphabetical
) key : Provider
● Yellow (
● Blue
(
(
To control the volume level :
● Red
) key : Transponder
● Press
/
keys to adjust the volume level.
● Press MUTE key to turn to silence mode.
● Press MUTE key again in order to cancel the mute function.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-10
GB-11
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTION
BASIC FUNCTIONS
5.1 Service Favorites
6. Program Information
● Press the Green (
) key on the control unit to select
/ keys to select a favorite
EPG-Electronic Program Guide
The electronic program guide gives you a channel list
for the channels.
the Favorites list.
● Use the
/
,
group that you want.
● Press the Green (
channel list.
Note : 1. This service depends on service
provider.
) key to toggle group and
2. After receiver recognized the GMT-time
from the signal which takes few seconds,
it can display correct EPG information.
5.2 Service Alphabetical
● Press EPG key while you are viewing a program.
● Press the Yellow (
) key on the remote control
unit to select the Alphabetical list.
This function is displayed on the screen by using only time.
You will see "EPG" in the LED display of the receiver.
● Use the
/
,
/
keys to select a
Alphabetical group that you want.
● Green
- Use to display the program list until this day last week by
● Press the Yellow (
) key to toggle group
(
) key
going back per one day.
and channel list.
● Yellow
- Use to display the program list until this day next week by
(
) key going forward per one day.
●
/
keys - Use to display the program list by 30minutes per block.
5.3 Service Provider
● Press the Blue (
) key on the remote control
With the TV/RADIO or FAV key you can browse among the various programs lists.
unit to select the Provider list.
● Select the channel by pressing
/
,
/
keys and press
● Use the
/
,
/
keys to select a Provider
key to watch this channel.
group that you want.
● Press the Blue (
channel list.
) key to toggle group and
7. Subtitle
When the current broadcasting program provides
subtitle, press the Green ( ) key to see
the current subtitle language list.
5.4 Service Transponder
To change the subtitle language:
● Press the Red (
) key on the remote control
● Press the Green (
) key to see the subtitle
unit to select the Transponder list.
language List.
● Use the
/
,
/
keys to select a
● Use the
language you want.
● Press the key and then the subtitle language you want is displayed
/
keys to select a subtitle
Transponder group that you want.
● Press the Red (
) key to toggle group and
channel list.
The menu display is carefully created and user friendly to assure the easy operation
of the receiver by the user.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-12
GB-13
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTION
OPERATING THE RECEIVER
8. Teletext OSD
Main Menu
When the current broadcasting program provides
After installing your antenna system and STB with appropriate connectors.
Teletext OSD, press the Green (
) key twice
● Plug in the AC main power and switch on the receiver.
to see the current Teletext OSD list.
● Press MENU key to bring up the main menu.
To change the Teletext OSD:
The following on screen display will appear:
● Use the
you want.
● Press the
/
keys to select a Teletext OSD
The sub menu topics will be displayed from 1 to 5.
For the sub-menus 1, 2 and 3 you need the PIN Code.
key and then the Teletext OSD
you want is displayed on the screen.
● You must follow the help message at the bottom
of the screen!
9. Teletext VBI
Before you begin with the "Installation"
menu, you should check in the 4th menu
"System Setup" whether all the information
there is applicable for you.
When the current broadcasting program provides
Teletext VBI, press the Green (
) key three times
to see the current Teletext VBI list.
To change the Teletext VBI:
● Use the
you want.
● Press the
/
keys to select a Teletext VBI
1. Installation
key and then the Teletext VBI
The menu provides settings for customizing, adding new services and displaying
the status of the receiver.
you want is displayed on the screen.
● Select "Installation" in the main menu mode to
select the sub menu.
● Enter the PIN Code.
If you have not entered your own PIN Code
then the PIN Code 0000 applies, which was
set at the factory.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-14
GB-15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE RECEIVER
OPERATING THE RECEIVER
● Select from Menu Mode:
1.1 LNB Setting
"User" mode :
Enables control of basic positioner function
recommended for beginners. General user uses “User” mode.
You can select the satellite and LNB setting conditions
to execute channel search and you can alter the settings
for 22KHz tone. The parameters set in this menu are
needed for programming the channels for the "Auto
scanning" and "Manual scanning".
"Installer" mode :
Complete control of the positioner’s full functions
recommended for installers and professional users.
The necessary information can be found at your antenna
and LNB brochures, or you can ask your dealer.
1.2.1 User Mode
● Select Driving Mode:
● Select LNB power supply "On".
You have an option to choose the positioner’s
movement type: Continuous, Step or Time.
● Position the antenna with north, south, east
● Select the desired satellite name.
● Select the LNB type (frequency).
● Select the DiSEqC Mode
and west and use the
motor. key drives to west, key drives to east,
key drives to north and key drives to south.
● If you finished driving of motor, select “Store
/
,
/
key to drive
(Off, DiSEqC A, DiSEqC B, DiSEqC C, DiSEqC D, Tone Burst A, Tone Burst B)
If you are using a Positioner, select this option. (“Yes” or “No”)
22KHz: In case you are using a dual LNB or two antennas connected to a 22 kHz
tone switch box, with the 22 kHz tone switch ("On", "Off" or "Auto") you
can switch between both LNB or antennas.
current Position.” and press
key, to reset
new driving motor.
Note : The level indicated in the “Signal Status” is only for reference.
The signal quality may be adequate even though the level indicated is
not maximum.
1.2 Positioner Setting
If you have a DiSEqC 1.2 motorized system, then you can take advantage of
the DiSEqC 1.2 functions available.
● Go to Stored Position.
When the stored position is reached then screen displays "Stop",
you can now continue with the further operations.
● Select Satellite.
● Select any transponder from above satellites and
check out the Frequency, Symbol Rate, FEC and
Polarity.
● Select the Calculate Sat Positions to recalculate the satellite position and
key.
In case problems arise, ask your dealer.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-16
GB-17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE RECEIVER
OPERATING THE RECEIVER
1.2.2 Installer Mode
1.4 Auto Scanning
After checking the positioner’s state, installer should use
this menu. He should set the “Disable Limits” before
using User mode.
The sub menu “Auto Scanning” will enable download of off-air channels automatically
from the preprogrammed satellites.
To download channels automatically:
You can select All/Off/Only Free option mode in
each satellite.
● Select the Drive Motor West/East and use the
/
keys to drive motor.
key drives to west and
key drives to east.
● Select “Enable Limit”, in order to enable “Set Limit”.
Off :
All :
No Scan
Scan all the channels
● Select “Disable Limit”, in order to disable “Set Limit”.
Only Free : Scan free channels
● Select “Reset Positioner” and
key to reset positioner.
● Press
key.
1.3 Solarsat Setting
Auto Scanning menu will be displayed.
This menu is only for the Solarsat antenna.
When you press this menu, you will get this message, “This menu is only for the
Solarsat antenna. If you have one-press OK, otherwise-press EXIT.”
All the channels in the list from the selected satellite will be
automatically downloaded.
After scanning you will see "Your digital receiver found..." .
Afterwards you return to Auto Scanning menu.
You can set the value according to your location.
● To set the Value of Date and Time, use the
/
1.5 Manual Scanning
keys to change the value.
● Use the
/
keys to change position.
keys to move each filed.
To tune-in new channels and weak signals, the STB has been provided with
the option "Manual Scanning" where the channel data can be entered by the user.
After selecting the "5. Manual Scanning" from the Installation Menu, the following
screen will be displayed:
● Use the
/
● Select the target satellite for manual search.
● Load a transponder.
This option will enable the user to load any
transponder from the preprogrammed list
available within the receiver.
Note : When you enter Frequency after setting
Load TR to New, the entered information
must include at least one channel to make
channel save possible.
● Input the frequency of the transponder you want to find.
● Input the symbol rate of the transponder you want to find.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-18
GB-19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE RECEIVER
OPERATING THE RECEIVER
● Select the FEC(Forward Error Correction)of the transponder
you want to find.
2. Channel Organising
You can select the value of 1/2, 2/3, 3/4, 5/6, 7/8 or Auto.
● Select the polarization of the transponder you want to find.
(Horizontal/Vertical/Circular Left/Circular Right)
In the case of horizontal, 18V and in the case of vertical,
13V are output through LNB line.
The "Channel Organising" menu has seven
functions:
The "Channel Organising" menu is used to delete
the Satellites, Transponders and Channels or to make
Favorite channels or move channel as you want.
● Select Scan Mode “All” or “Only Free”.
● Enter the PIN Code.
● Select Network searching “Yes”.(“No” is default).
You can find more transponders using the home network.
● Select PID searching “Yes”.(“No” is default). You can manually search by
entering individual PID(Packet Identifier)(Video/Audio/PCR) values.
If you have not entered your own PIN Code PIN Code
0000 applies, which was set at the factory.
● After select option, press
key to start the scan process.
2.1 Delete Satellite
1.6 SMATV Scanning
● Select the desired satellite list you want to delete
by pressing Red (
) key.
In case that several generations use Antenna and LNB
in common, search the service the from 950 to 2150MHz.
● Press key for confirmation.
Note : This feature doesn’t delete satellite itself
but deletes the list of channels registered
for satellite.
● Select Searching Type “Automatic” or “Manual”.
● Select Scan Mode “All” or “Only Free”.
● You can input alternative symbol rate from 1 to 4
Note : 1. When your searching type is set to Automatic
during SMATV scanning, you have only to enter
the alternative symbol rate(1~4) you want.
2.2 Delete Transponder
● Select the desired transponder list you want to
2. When your searching type is set to Manual
during SMATV scanning, you must enter both
frequency and symbol rate.
delete by pressing Red (
● Press key for confirmation.
) key.
Note : This feature doesn’t delete transponder itself
but deletes the list of channels registered for
transponder.
1.7 Reset to Factory Defaults
This to restore the factory set values in case the user
has encountered some problems after changing any
values of channel data and others which may be in error.
At the request window,
if you press
key, the receiver will be reset to factory
default settings automatically.
Note : This cause your previous settings to be deleted!
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-20
GB-21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE RECEIVER
OPERATING THE RECEIVER
2.3 Delete Channel
2.7 Move & Edit Channel
● Select the desired channel you want to delete by
pressing Red ( ) key.
● Press key for confirmation.
● Select the desired list with
● Select channel by pressing Red (
● Press keys to change the position
/
keys.
) key.
/
,
/
of the channel you want, and press
confirmation.
key for
● Press Red (
) key again to return to
2.4 Delete All Channels
previous state.
● If you want to return the channel to the initial
position, do not press key but press
blue ( ) key.
At the request window, press
all channels and press MENU / EXIT to exit.
key to delete
● To edit channel name, press Green (
) key.
, and
Font Table will be displayed.
2.5 Delete Scrambled Channels
● Select desired character with
then press key to paste character to the string.
● Press MENU key to save tge set data.
/
,
/
At the request window, press
key to delete
scrambled channels and press MENU / EXIT to exit.
2.6 Favorite Channels
You can change TV list or Radio list by TV/RADIO key
and change favorite list by FAV key. This enables you to
create the 9 favorite TV and Radio list.
● Select the desired channel list with
/
keys.
● When you press the TV/RADIO key, TV list and Radio
list are toggled.
Right List : Adds a channel to the left list by pressing
the Red (
Left List : Deletes a channel by pressing the Red
) key.
● Press FAV key to select another favorite list.
● Then press key for confirmation.
) key.
(
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-22
GB-23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE RECEIVER
OPERATING THE RECEIVER
3.2. Change PIN Code
3. Parental Lock
To change the PIN Code, select the second option "Change PIN Code".
This "Parental Lock" feature sets viewing restrictions
and prevents unauthorized access to your STB through
the PIN (Personal Identification Number),
which is a 4 digit number.
This will take you to the following menu:
In this option, you need to enter the current PIN
Code at the first cursor, and at the second cursor
enter the desired PIN Code.
To confirm, you need to enter the new PIN code
again.
(The factory preset PIN Code : 0000)
On selecting this menu, you will have two options:
to set lock for any desired channel and to change
your PIN value.
Please remember the PIN Code should be a 4 digit
numerical value.
● Enter PIN Code.
If you have not entered your own PIN Code then the PIN Code 0000 applies,
which was set at the factory.
THE FACTORY PRESET PIN CODE : 0 0 0 0.
3.1 Set Channel Lock
● Select the channel by pressing
/
,
/ , ,
/
.
● When you press the TV/RADIO key, TV list and Radio
list are toggled.
● Select the channel lock by pressing Red (
● Press key for confirmation.
) key.
This will lock the channel. Whenever you need to view
the channel, you will have to enter the PIN at the request
window.
To cancel the lock :
● Press Red (
) key again in order to cancel the lock.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-24
GB-25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE RECEIVER
OPERATING THE RECEIVER
4.3 Media Settings
4. System Setup
You can set the various media settings you want.
This option enables you to change the factory preset
system settings as per your requirements.
Place the cursor on this sub menu and press
.
● Select the TV system : PAL, SECAM.
● Select the TV type according to your TV:
STANDARD 4: 3 ratio or WIDE SCREEN
16 : 9 ratio type.
● Select the aspect ratio conversion :
Letter box, Pan & Screen, Mixed or Full.
● Select the Video Signal Type :
Composite+RGB or Composite.
4.1. Language Selection
The "Language Selection"option allows the user to
select the desired language of the OSD, Soundtrack,
Teletext, Subtitle or EPG.
4.4 Time & Timer Setting
● To accommodate user from different regions
speaking different languages, OSD languages are
available 19 languages.
● Place the cursor on this sub menu and press
.
● Press the
/
,
/
keys to change the Local
time in Time Zone.
● To select the desired language menu,
The local time will be changed according to your
location.
press
/
keys to change language and press
.
● The OSD Language, Soundtrack, Teletext, Subtitle,
● Press the
/
keys to choose event repetition
or EPG will vary according to the selected language.
you want to reserve :
Daily, Every Sunday, Every Monday, Every Tuesday,
Every Wednesday, Every Thursday, Every Friday,
Every Saturday, Once.
4.2 OSD Setting
You can set the OSD transparency and the display time.
● Press the Numerical
and press the keys to choose a switch time
you want to reserve.
● Select TV program to set the event program by
pressing keys.
~
) keys to set the time you want
/
● Select OSD Transparency type.
The OSD Transparency level from 0 to 100%.
● Set the display duration of the information(banner) box
displayed in the screen.
/
When you press the TV/RADIO key, TV program and Radio program
are toggled.
The time ranges from 0.5 to 60.0 seconds.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-26
GB-27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE RECEIVER
OPERATING THE RECEIVER
4.5 System Information
5. Embedded Viacces (For model DSB-9401V)
If you have to contact your service provider or a service
center they might ask for information available from this
menu.
1. Change PIN Code:
Change the PIN Code of the Smartcard,
if necessary.
Place the cursor on this sub menu and press
The following will be the on-screen display.
key.
2. Change Parental Rating:
Change the setting for the family filter,
if necessary.
Note : This service is not offered by all channels.
4.6 Software Upgrade
3. Change Lock indicator:
You can change the lock status of the Viaccess Smartcard.
You can download and upgrade the software of this
STB through ASTRA, Sirius and Hotbird satellite when
the new software is released.
4. Issuer Information:
Here you can call up all information stored on
the Smartcard by the publisher.
During downloading don’t turn off the STB.
5. Authorization:
If there is a new version of software to download,
you are asked if you will update or not.
This option would indicate the authorization status
of the Smartcard.
If you press
key, the update starts right away.
In case update is impossible, you get this message
"You can’t update software!" Or in case you don’t need to update,
"You don’t need to update software!" will be displayed.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-28
GB-29
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
1. User section
4000 programmable channels,
Problem
Possible cause
Solution of the problem
auto and manual scan facility,
channel organizing (programmable),
SCARTS output,
software download via satellite & PC,
advanced Electronic Program Guide,
multi-language supported for OSD,
DiSEqC 1.2 supported full function
infrared remote control unit,
No display LED on
the front panel;
No power supply
Power cord
not plugged in correctly
Power cord plug in correctly
Back switch in correctly
low power consumption
No pictures on the screen
Receiver in Standby mode;
Scart not connected tightly
to video output of television;
incorrect channel or video
output selected on television
Set receiver to "On";
Check connection and correct;
2. Tuner section
950 ~ 2150 MHz wide band tuner,
supporting DiSEqC 1.2 version,
Check channel and video output and
correct (TV instruction manual)
13 V/18 V switching,
22 kHz continuous tone control
No sound
Audio cord connected
incorrectly;
Loudness level = 0;
Muting active
Check connection and correct;
3. Video section
DVB-S compliant,
MPEG-2 video (MP@ML)
2 - 45 Ms/s symbol rate
Increase loudness on television set;
Press the MUTE key
compatible for both SCPC/MCPC,
supports aspect ratio 4:3 (normal) and
16:9 (wide screen)
Remote Control does not
operate directly
incorrect operation;
Point remote control
towards the Receiver.
Batteries dead or inserted
incorrectly
Replace batteries or insert correctly
4. Audio section
32, 44.1 and 48 kHz sampling
frequencies,
volume control and mute function through
Remote Control Unit.
MPEG 1 audio layer I & II
mono, dual, stereo and joint stereo audio
mode,
Poor picture quality
Signal strength too low
Check the signal strength in
the "Auto Scan" menu, correct alignment
of your antenna
Power supply
Type:
On-Screen Error Message
"Searching for signal"
Antenna cable not connected
or not tight;
Check connection and correct;
SMPS
Input Voltage:
Power Consumption:
Stand by:
100-240V AC 50/60Hz
Max. 25W
11W
LNB defective;
incorrect position of the
satellite antenna;
Change LNB;
Check position and correct,
Check the signal strength in
the "Auto Scan" menu
VIDEO DECODER
Transport
Transport stream
On-Screen Error Message
"Channel data
does not exist."
Satellite not yet set
Scan of in "Automatic scanning"
or "Manual scanning" menu
MPEG-2 ISO/IEC 13818
Transport stream Specification
MPEG-2 MP@ML
Up to 100Mbps
4:2:2
On-Screen Error Messages: Smartcard:
"Please check the
Smartcard";
"Please insert the
Smartcard".
(depend on model)
Check the Smartcard.
"Insert the Smartcard."
- not plugged in correctly;
- not plugged in.
Input Rate
YUV format
Aspect ratio
Resolution
4:3, 16:9
720 x 576, 704 x 576,
544 x 576, 480 x 576,
352 x 576, 352 x 288
0.5, 2.0 in both horizontal and vertical
directions
DISPOSAL
The device, packaging material (e.g. Styrofoam) and the batteries
Scale
must never be disposed of with household refuse.
Please obtain appropriate information about the regulations in your community,
and dispose of all refuse in accordance with regulations at the separate
locations provided.
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-30
GB-31
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
NETWORK INTERFACE (Broadcasting - Digital)
BASE-BAND AUDIO/VIDEO OUTPUT
Interface
Front end
One LNB input
VIDEO
PAL, SECAM
Interface: 2 SCART (TV, VCR)
Impedance: 75
Output level:1Vp-p
Differential gain: 5% max
Signal to noise ratio: 60dB min (digital)
DVB-S compliant digital satellite
receiver (ETS 300 421)
Convolutional Code Rate 1/2, 2/3, 3/4,
5/6 and 7/8 with constraint Length K=7
950 ~ 2150Mhz
FEC Decoder
Input frequency range
NF
12dB (typical)
Input Connector
Input Symbol Rate
Input Signal Level
DiSEqC
LNB Power &
Polarsation
F-type, IEC 169-24, Female
2 ~ 45 Msps
AUDIO
Inteface: Scart
Impedance: 600 balance
Output level: 3.0Vp-p max (controllable)
Frequency response:
ע 3dB (20~15kHz)
Signal to noise ratio: 60dB min (digital)
S/PDIF (Digital Audio Output)
-65dBm ~ -25dBm at 75
DiSEqC 1.2 (500mA max)
Vertical: +12V ~ +14V
Horizontal: +17V ~ +19V
Current: Max. 500mA, Overload
Protection
22kHz Tone
Frequency: 22
ע 4kHz Amplitude: 0.6
ע 0.2v QPSK
MEMORY
Flash
SDRAM
2MB
8MB
Demodulation
Outer FEC:
Reed Solomon Coding (204,188), t = 8
PHISICAL SPECIFICATION
AUDIO DECODER
Size (W x D x H)
Weight (Net)
233 x 176 x 38 mm
0.95Kg
Decoding
Sampling rate
Audio mode
MPEG-1 layers I, II
Up to 256kbps
Single mode, dual mono, stereo,
joint stereo
D
I
G
I
T
A
L
S
A
T
E
L
L
I
T
E
R
E
C
E
I
V
E
R
GB-32
GB-33
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Quadra Fire Indoor Fireplace CASTILEI CE MBK User Guide
Quantum Wheelchair Q6 Edge HD User Guide
Radio Shack Radio TRC 442 User Guide
Riccar Sewing Machine REC 5900 User Guide
Roberts Radio Portable Radio R9947 User Guide
Roland Musical Instrument HP107 User Guide
Roland Musical Instrument KR105 User Guide
Samsung Speaker System HW F550 User Guide
Sansui Flat Panel Television HDLCDVD325 User Guide
Sanyo Flat Panel Television DP50719 User Guide