XP510i Quick Start
XP510i Quick Start cont’d
Specifications*
System Specifications
Maximum Output Power
250 W + 250 W @ 8 Ω
Unpacking and Setting Up the XP510i
Using a Line Level Signal
Crosstalk (at 1 kHz)
• Unpack all the system components from the shipping carton and save all packing materials in the (unlikely) event
your unit ever needs to be returned for service.
• Be sure that the XP510i’s Power switch is set to the OFF position.
-70 dB between input channels
-70 dB between input/output channels
E PEDITION
• Turn all of the channel VOLUME (VOL) controls fully counterclockwise to the “0”position.
• Connect the power cable to an AC outlet.
Maximum Output Level (0.5% T.H.D. @ 1kHz)
+22dBu(MONITOR L/R) @ 10 kΩ
+14 dBu (REC) @ 10 kΩ
• Remove the mixer by turning the quarter turn screw counterclockwise towards the RELEASE position.
PORTABLE PA SYSTEM
SPEECH/MUSIC
167 Hz, 3dB/Octave
XP510i
LOCK
• If using channels 1-4, set the MIC/LINE switch to the LINE position.
T.H.D
Input Channel Equalization
HIGH: 10 kHz shelving 15 dB
LOW: 100 Hz shelving 15 dB
<0.1% @+14 dB 20 Hz ~ 20 kHz (MONITOR L/R,REC L/R) @ 10 kΩ
• Using standard 1⁄4-inch cables, connect a line level signal from a keyboard into the XP510i’s LINE INPUTS.
Frequency Response
RELEASE
20 Hz ~ 20 kHz +/-1 dB, 10 kΩ (MONITOR L/R)
20 Hz ~ 20 kHz +0/-1 dB, 10 kΩ (REC L/R)
LIMIT/COMP Switch
DOWN = Comp, UP = Limit (CH1/2)
Hum and Noise (Input GAIN=Maximum Input sensitivity, MIC)
-112dBu equivalent input noise ( Rs = 150 Ω )
Phantom Power
+15V DC
• Carefully hold the mixer to remove it from the speaker.
-90dBu
-80dBu
Residual noise (MONITOR L/R) all Levels at Minimum
MONITOR at nominal level and all channel Levels
minimum.
Power Source/Power Consumption
AC INPUT 100 V~240 V, 50/60 Hz, 600 W MAX.
Electric Acoustic
Guitar
-70dBu
MONITOR at maximum level and all channel Levels
minimum.
Weight
52.8 Ib (24 Kg)
Maximum Voltage Gain
50dB MIC 1/2(XLR,LIMIT Position) IN TO MONITOR L/R
60dB MIC 3/4(XLR) IN TO MONITOR L/R
40dB MIC 1/2(PHONE TRS,LIMIT Position) IN TO MONITOR L/R
50dB MIC 3/4(PHONE TRS) IN TO MONITOR L/R
14dB CH 1/2 LINE(PHONE TRS,LIMIT Position,MIC/LINE SW IN) IN TO
MONITOR L/R
Dimensions
22.7’’(W) x 12.6’’(D) x 22’’(H)
577 mm(W) x 320 mm(D) x 560 mm(H)
Owners Manual
Where 0 dBu = 0.775 V and 0 dBV = 1 V
24dB CH 3/4 LINE(PHONE TRS,MIC/LINE SW IN) IN TO MONITOR L/R
28dB ST LINE IN TO MONITOR L/R
48dB MIC 3/4(XLR) IN TO REC L/R
• Remove the accessory compartment cover by turning the quarter turn screw counterclockwise towards the
RELEASE position, and remove the included speaker cables.
• Switch the XP510i’s Power switch to the ON position.
• Play your guitar or keyboard and slowly raise the channel control and the MASTER level control until you have
reached the desired VOLUME.
Introduction
Configuring the XP510i for Transport
Input Specifications
Thank you for purchasing the Expedition XP510i PORTABLE PA SYSTEM from Samson! The XP510i features a com-
pact, 10-channel mixer with 500 watts of onboard power and dual 2-way speakers, making it an ideal solution for
a variety of small to medium sized PA applications. The XP510i is extremely portable thanks to its lightweight and
unique “Slide and Lock”design.
You can easily carry your sound system using the XP510i’s “Slide and Lock”feature. The “Slide and Lock”speaker
enclosures allow you to connect both speakers together into a single, easy to carry unit. Follow these steps to
configure the XP510i for easy transport.
Input Connector
Input Impedance
Nominal Source
Impedance
Rated Input Level
Connector Type
CH MIC
3.6 kΩ / 7.5 kΩ
50 ~ 600 Ω / 600 Ω
-32 dBu / -22dBu
XLR Type Balanced
/ Phone Jack (TRS)
T=Hot R=Cold
S=GND
The 10-channel mixer can be removed from the speaker for tabletop use. It features 4 inputs for connecting micro-
phones, plus three inputs for connecting stereo signals, like those from a CD player or electronic keyboard. There’s
also a built-in, 24-bit digital effects processor to add studio quality effects to your voice or instruments. For music
playback, the XP510i features a convenient iPod dock. The mixer also provides a robust output, with 500 watts of
total power from the lightweight, Class D amplifier section. The XP510i employs a matched speaker system with
dual 2-way enclosures that have proprietary 10-inch woofers and 1-inch high frequency drivers. To help project
the sound to a larger audience, the XP510i speakers can be mounted on standard speaker stands, thanks to the
integral pole mount receptacles. The XP510i is constructed using durable ABS, high impact plastic, making it super
road tough, and at the same time, lightweight.
1. Place one speaker on the floor and set it on its side.
3. Slide the second speaker into the speaker on the
floor making certain that the two speakers stay parallel
to each other.
• Replace the accessory panel by aligning the bottom of the panel into the slots, make sure the quarter turn screw
is in the RELEASE position; then close the panel and turn the quarter turn screw clockwise to LOCK.
CH LINE
3.6 kΩ / 7.5 kΩ
50 ~ 600 Ω / 600 Ω
-6 dBu / +4 dBu
XLR Type Balanced
/ Phone Jack (TRS)
T=Hot R=Cold
S=GND
• Position the speakers on the floor or on stands, and using one of the included speaker cables, connect the mixer’s
LEFT SPEAKER OUT to the left speaker’s input connector. Next, use the second included speaker cable to connect
the RIGHT SPEAKER OUT to the right speaker’s input connector.
STEREO INPUT
STEREO INPUT
10 kΩ
10 kΩ
600 Ω
600 Ω
0 dBu
0 dBu
Unbalanced Phone
Jack
In this manual, you’ll find a detailed description of the features of the XP510i PA system, as well as a description of
its front and rear panels, step-by-step instructions for its setup and use, and full specifications. You’ll also find a war-
ranty card enclosed—please don’t forget to fill it out and mail it in so that you can receive online technical support,
and so we can send you updated information about these and other Samson products in the future. Also, be sure
RCA pin Jack
2. Position the second speaker above the first speaker
and line up the “Slide and Lock”tracks and grooves so
that they are parallel to the speaker on the floor.
4. You will feel a slight click when the two speakers are
Output Specifications
Rated Output
in place.
Output Connector Output Impedance
Nominal Load
Impedance
Connector type
Level
With proper care and adequate air circulation, your XP510i will operate trouble free for many years. We recommend
you record your serial number in the space provided below for future reference.
MONITOR L/R
1 kΩ
≥10 kΩ
+4 dBu
Phone Jack (TRS)
Impedance bal-
anced T=hot R=Cold
S=ground
Serial number:_______________________________
Date of purchase:____________________________
REC OUT
600 Ω
≥10 kΩ
8 Ω
+4 dBu
250 W
RCA pin Jack
Phone Jack
Should your unit ever require servicing, a Return Authorization number (RA) must be obtained before shipping
your unit to Samson. Without this number, the unit will not be accepted. Please call Samson at 1-800-3SAMSON
(1-800-372-6766) for a Return Authorization number prior to shipping your unit. Please retain the original packing
materials and if possible, return the unit in the original carton and packing materials. If you purchased your Sam-
son product outside the United States, please contact your local distributor for warranty information and service.
SPEAKER OUTPUT
*Specifications and design subject to change without notice
Speaker cabinets must be reversed with respect to top and
bottom.
Using a Microphone
• Be sure that the XP510i’s Power switch is set to the OFF position.
• Turn all of the channel VOLUME (VOL) controls fully counterclockwise to the “0”position.
• If the speakers are not connected, connect the speaker wires as described in the previous section.
• Next, connect the power cable to an AC outlet.
Features
XP510i Wiring Guide
There are several ways to interface the XP510i to support a variety of applications. The XP510i features balanced
inputs and outputs, so connecting balanced and unbalanced signals is possible.
Dimensions
• The XP510i is a compact PA system with dual 2-way speakers, onboard mixer and 500 watt power amplifier.
CONNECTING THE XP510i
301
320
• The XP510i is the ultimate in portable design. The lightweight and clever design allow you to connect all the
pieces together into a single, easy to move case.
• Using a standard XLR cable, plug a microphone into the XP510i’s Channel 1 MIC INPUT.
Unbalanced 1/4” Connector
173
88
• The mixer is stored in one of the speaker cabinets; the other cabinet has an accessory compartment for storing
the speaker cables, microphones, etc.
• The speakers are 2-way vented enclosures with 10-inch woofers for deep bass, complimented by a 1-inch high
frequency driver, set in a custom horn with a 60 x 90 degree coverage pattern producing a clean, clear sound.
• The internal 2 x 250 watt lightweight Class D power amplifier produces a powerful stereo sound.
Balanced TRS 1/4” Connector
• The XP510i’s mixer can be removed from the speaker for tabletop use and you can use the kick stand to set the
mixer at an ergonomically correct angle.
• The 10-channel mixer features four Mic/Line inputs allowing you to connect microphones or line signals, plus
three stereo inputs for connecting line signals from keyboards, drum machines and MP3/CD players. You can
engage the Phantom Power switch if you are using condenser microphones.
• On each of the mixer’s channel inputs there is a Bass and Treble control allowing you to equalize the tone of the
individual inputs.
XLR Balanced Wiring Guide
• To create a lush sound on any of the microphone channels, you can select from the ten, onboard, 24-bit digital
effects.
• Switch the XP510i’s Power switch to the ON position.
• Set the MIC/LINE switch to the MIC position.
• The XP510i features a built-in iPod dock allowing you to easily connect most iPod models for seamless music
playback. You can use the iPod to simply play music, add background tracks, or repeat a commercial message at a
fair or trade show.
• Set the Channel 1 VOLUME (VOL) control to about halfway.
• For added flexibility, the XP510i’s mixer has a Monitor Out on two, 1/4 inch jacks allowing you to connect to exter-
nal powered monitor speakers.
• While speaking into the microphone, slowly raise the MASTER level control until you have reached the desired
level.
Download from Www.Somanuals.com. All Manuals Search And Download.
|