OPERATOR’S MANUAL
10 in. TABLE SAW
BTS21
Your table saw has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
SECUREWORK.Useclampsoravisetoholdworkwhen
practical. It’s safer than using your hand and frees both
hands to operate tool.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
DON’T OVERREACH. Keep proper footing and
balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
andcleanforbetterandsaferperformance.Followinstruc-
tions for lubricating and changing accessories.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the operator’s
manual carefully. Learn the saw’s applications and
limitationsaswellasthespecificpotentialhazardsrelated
to this tool.
DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected.
AVOID ACCIDENTAL STARTING. Be sure switch is off
GUARDAGAINSTELECTRICALSHOCKBYPREVENT-
ING BODY CONTACT WITH GROUNDED SURFACES.
For example, pipes, radiators, ranges, refrigerator enclo-
sures.
when plugging in any tool.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may risk injury.
KEEP GUARDS IN PLACE and in good working order.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habitofcheckingtoseethatkeysandadjustingwrenches
are removed from tool before turning it on.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefullycheckedtodeterminethatitwilloperateproperly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
KEEPWORKAREACLEAN.Clutteredareasandbenches
invite accidents. DO NOT leave tools or pieces of wood
on the saw while it is in operation.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visi-
tors should wear safety glasses and be kept a safe
distance from work area. Do not let visitors contact
tool or extension cord while operating.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade
or cutter only.
MAKE WORKSHOP CHILDPROOF with padlocks and
master switches, or by removing starter keys.
NEVERLEAVETOOLRUNNINGUNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
DON’T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
USE RIGHT TOOL. Don’t force the tool or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
USETHEPROPEREXTENSIONCORD. Makesureyour
extensioncordisingoodcondition.Useonlyacordheavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage result-
ing in loss of power and overheating. A wire gauge size
(A.W.G.) of at least 14 is recommended for an extension
cord 25 feet or less in length. If in doubt, use the next
heaviergauge.Thesmallerthegaugenumber,theheavier
the cord.
during extended periods of operation.
DO NOT ABUSE CORD. Never yank cord to disconnect
fromreceptacle.Keepcordawayfromheat,oil,andsharp
edges.
USE OUTDOOR EXTENSION CORDS. When tool
is used outdoors, use only extension cords with
approved ground connection that are intended for use
outdoors and so marked.
DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
ALWAYS KEEP THE BLADE GUARD AND SPREADER
(SPLITTER) IN PLACE and in working order.
KEEP BLADES CLEAN, SHARP, AND WITH
SUFFICIENT SET. Sharp blades minimize stalling
and kickback.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from blades. Do not reach underneath
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
work or around or over the blade while blade is rotating.
Do not attempt to remove cut material when blade is
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
moving.
STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
USE ONLY CORRECT BLADES. Do not use blades with
incorrect size holes. Never use blade washers or blade
bolts that are defective or incorrect. The maximum blade
capacity of your saw is 10 in. (254 mm).
BEFORE MAKING A CUT, BE SURE ALL ADJUST-
MENTS ARE SECURE.
BLADE COASTS AFTER BEING TURNED OFF.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY. If dam-
aged, have repaired by a qualified service technician at
anauthorizedservicefacility.Theconductorwithinsulation
havinganoutersurfacethatisgreenwithorwithoutyellow
stripes is the equipment-grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
do not connect the equipment-grounding conductor to a
live terminal. Repair or replace a damaged or worn cord
immediately. Stay constantly aware of cord location and
keep it well away from the rotating blade.
BE SURE BLADE PATH IS FREE OF NAILS. Inspect for
and remove all nails from lumber before cutting.
NEVER TOUCH BLADE or other moving parts during
use.
INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole elec-
trical receptacle.
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely
understood or if in doubt as to whether the tool is properly
grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool's plug.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified
electrician.
NEVER START A TOOL WHEN ANY ROTATING COM-
PONENT IS IN CONTACT WITH THE WORKPIECE.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
WHENSERVICINGuseonlyidenticalreplacementparts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLY RECOMMENDED ACCESSORIES listed
in this manual or addendums. Use of accessories that
are not listed may cause the risk of personal injury.
Instructions for safe use of accessories are included
with the accessory.
DOUBLE CHECK ALL SETUPS. Make sure blade is
tight and not making contact with saw or workpiece
before connecting to power supply.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning. Never
SPECIFIC SAFETY RULES
FIRMLY BOLT THE SAW TO A WORK BENCH OR LEG
STAND at approximately hip height.
NEVER OPERATE THE SAW ON THE FLOOR.
GUARD AGAINST KICKBACK. Kickback occurs when
the blade stalls rapidly and workpiece is driven back
Through-sawing operations are those in which the blade
cuts completely through the workpiece as in ripping or
cross cutting. Keep the blade guard down, the anti-kick-
back pawls down, and the spreader in place over the
blade.
towards the operator. It can pull your hand into the blade ALWAYS SECURE WORK firmly against the rip fence or
resulting in serious personal injury. Stay out of blade path
and turn switch off immediately if blade binds or stalls.
USE RIP FENCE. Always use a fence or straight edge
guide when ripping.
SUPPORT LARGE PANELS. To minimize risk of blade
pinching and kickback, always support large panels.
REMOVE ALL FENCES AND AUXILIARY TABLES
before transporting saw. Failure to do so can result in an
accident causing possible serious personal injury.
ALWAYS USE BLADE GUARD, SPREADER, AND ANTI-
KICKBACK PAWLS on all “through-sawing” operations.
miter fence. NEVER use the rip fence during the same
operation as the miter fence.
ALWAYS USE A PUSH STICK FOR RIPPING
NARROW STOCK. A push stick is a device used to push
a workpiece through the blade instead of using your
hands. Size and shape can vary but the push stick must
always be narrower than the workpiece to prevent the
push stick from contacting the saw blade. When ripping
narrow stock, always use a push stick, so your hand does
not come close to the saw blade. Use a featherboard and
push blocks for non-through cuts.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETY RULES
IF THE POWER SUPPLY CORD IS DAMAGED, it must
NEVER perform any operation “freehand” which means
using only your hands to support or guide the workpiece.
Always use either the rip fence or miter fence to position
and guide the work.
NEVER stand or have any part of your body in line with
the path of the saw blade.
be replaced only by the manufacturer or by an authorized
service center to avoid risk.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause your hand
to move into the cutting tool.
NEVER reach behind, over, or within three inches of the
blade or cutter with either hand for any reason.
MOVE THE RIP FENCE out of the way when cross cut-
ting.
DO NOT USE THE MITER FENCE AND RIP FENCE
during the same operation.
NEVER use rip fence as cutoff gauge when cross
cutting.
NEVER attempt to free a stalled saw blade without first
turning the saw OFF and disconnecting the saw from the
power source.
PROVIDE ADEQUATE SUPPORT to the rear and sides of
the saw table for wide or long work pieces. Use a sturdy
“outrigger” support if a table extension more than 24
inches long is attached to the saw.
AVOID KICKBACKS (work thrown back toward you)
by:
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are
not listed may cause the risk of personal injury. Instruc-
tions for safe use of accessories are included with the
accessory.
MAKE SURE THE WORK AREA HAS AMPLE LIGHTING
to see the work and that no obstructions will interfere with
safe operation BEFORE performing any work using the
table saw.
ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power
supply.
THIS TOOL should have the following markings:
a) Wear eye protection.
b) Use saw blade guard and spreader/riving knife for
every operation for which it can be used, including
all through sawing.
a) Keeping blade sharp.
c) Keep hands out of the line of saw blade.
d) Use a push stick when required.
e) Pay particular attention to instructions on reducing
risk of kickback.
b) Keeping rip fence parallel to the saw blade.
c) Keeping spreader, anti-kickback pawls, and
blade guard in place and operating.
d) Not releasing the work before it is pushed all the
way past the saw blade using a push stick.
e) Not ripping work that is twisted or warped or
does not have a straight edge to guide along the
fence.
f) Do not perform any operation freehand.
g) Never reach around or over the saw blade.
SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instruct other users. If you loan
someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Watt
Frequency (cycles per second)
Power
min
Minutes
Time
Alternating Current
Direct Current
Type of current
Type or a characteristic of current
Rotational speed, at no load
Double-insulated construction
Revolutions, strokes, surface speed, orbits, etc., per minute
n
o
No Load Speed
Class II Construction
Per Minute
.../min
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
To reduce the risk of injury or damage, avoid contact with any
hot surface.
Hot Surface
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
WARNING:
CAUTION
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
WARNING:
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to the nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand com-
pletely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual,
do not use this product. Call Ryobi customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
SPEED AND WIRING
EXTENSION CORDS
The no-load speed of this tool is approximately 5,000
RPM. This speed is not constant and decreases under
a load or with lower voltage. For voltage, the wiring in a
shop is as important as the motor’s horsepower rating. A
line intended only for lights cannot properly carry a power
tool motor. Wire that is heavy enough for a short distance
will be too light for a greater distance. A line that can
support one power tool may not be able to support two
or three tools.
Use only 3-wire extension cords that have 3-prong ground-
ing plugs and 3-pole receptacles that accept the tool’s plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter’s Laboratories (UL) should be used.
GROUNDING INSTRUCTIONS
**Ampere rating (on tool data plate)
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding conduc-
tor and a grounding plug. The plug must be plugged into a
matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
100'
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conduc-
tor can result in a risk of electric shock. The conductor with
insulation having an outer surface that is green with or with-
out yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is neces-
sary, do not connect the equipment-grounding conductor
to a live terminal.
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters “WA” on the cord’s jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
WARNING:
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet
like the one shown in figure 1. It also has a grounding pin
like the one shown.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
ELECTRICAL CONNECTION
This tool is powered by a precision built electric motor. It
should be connected to a power supply that is 120 volts,
60 Hz, AC only (normal household current). Do not operate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If the
saw does not operate when plugged into an outlet, double
check the power supply.
GROUNDING
PIN
120 V GROUNDED OUTLET
Fig. 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
Non-Through Cuts
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Anti-Kickback Pawls (radial arm and table saws)
A devise which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Pilot Hole (drill presses)
A small hole drilled in a workpiece that serves as a guide for
Arbor
drilling large holes accurately.
The shaft on which a blade or cutting tool is mounted.
Push Blocks (for jointer planers)
Bevel Cut
Device used to feed the workpiece over the jointer planer
cutterhead during any operation. This aid helps keep the
operator’s hands well away from the cutterhead.
A cutting operation made with the blade at any angle other
than 90° to the table surface.
Chamfer
Push Blocks and Push Sticks (for table saws)
A cut removing a wedge from a block so the end (or part of
Devices used to feed the workpiece through the saw blade
during cutting operations. A push stick (not a push block)
should be used for narrow ripping operations. These aids
help keep the operator’s hands well away from the blade.
the end) is angled rather than at 90°.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Cross Cut
Resaw
A cutting or shaping operation made across the grain or the
width of the workpiece.
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Cutterhead (planers and jointer planers)
A rotating cutterhead with adjustable blades or knives. The
blades or knives remove material from the workpiece.
Resin
A sticky, sap-based substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Dado Cut
A non-through cut which produces a square-sided notch or
trough in the workpiece (requires a special blade).
Ripping or Rip Cut
A cutting operation along the length of the workpiece.
Featherboard
A device used to help control the workpiece by guiding
it securely against the table or fence during any ripping
operation.
Riving Knife/Spreader/Splitter (table saws)
A metal piece, slightly thinner than the blade, which helps
keep the kerf open and also helps to prevent kickback.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter gauge, or other aids.
Set
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Gum
A sticky, sap-based residue from wood products.
Snipe (planers)
Heel
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Alignment of the blade to the fence.
Kerf
Through Sawing
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
The material removed by the blade in a through cut or the
slot produced by the blade in a non-through or partial cut.
Kickback
Throw-Back
A hazard that can occur when the blade binds or stalls,
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being placed
inadvertently in contact with the blade.
throwing the workpiece back toward operator.
Leading End
The end of the workpiece pushed into the tool first.
Workpiece or Material
The item on which the operation is being done.
Miter Cut
A cutting operation made with the workpiece at any angle
Worktable
to the blade other than 90°.
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Rating .............................................. 120 V, 60 Hz, AC only
Input .....................................................................15 Amps
No Load Speed ....................................5,000 r/min. (RPM)
Cutting Depth at 0˚: ..............................................3-1/2 in.
Cutting Depth at 45˚: ............................................2-1/2 in.
Blade Arbor ..............................................................5/8 in.
Blade Diameter.......................................................... 10 in.
Blade Tilt .................................................................0˚ - 45˚
Net Weight without Leg Stand ............................. 61.5 lbs.
Net Weight with Leg Stand................................... 82.5 lbs.
SPREADER
ANTI-KICKBACK
PAWLS
BLADE
GUARD
TABLE
EXTENSION
RIP FENCE
LOCK
KNOB
SLIDING
MITER TABLE
SCALE
OUTFEED
SUPPORT
MITER
FENCE
LOCKING LEVER
TABLE TILT
HANDLE
MITER SCALE
BEVEL
LOCKING
LEVER
SWITCH
ASSEMBLY
BEVEL
INDICATOR
HEIGHT/BEVEL
ADJUSTING HANDWHEEL
STORAGE
BRACKET(S)
LEVELING
FOOT
BEVEL
SCALE
FRONT
RAIL
LEG
STAND
Fig. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
HEIGHT/BEVEL ADJUSTING HANDWHEEL - Located on
KNOW YOUR TABLE SAW
the front of the cabinet, use this handwheel to lower and raise
the blade for height adjustments or blade replacement. This
handwheel also makes the adjustment for bevel angles.
See Figure 2.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
wellasaknowledgeoftheprojectyouareattempting.Before
use of this product, familiarize yourself with all operating
features and safety rules.
LEG STAND - Attached to the table saw base, the leg stand
opens and closes with ease making transportation simple.
MITER FENCE WITH LOCK KNOB - The fence attaches
to the sliding miter table and can be angled for miter and
compound miter cuts as well as straight cuts such as cross
cuts and bevel cross cuts. With the locator pin in place, this
knob locks the miter fence to the sliding miter table at the
desired cutting angle.
ANTI-KICKBACK PAWLS - Kickback is a hazard in which
the workpiece is thrown back toward the operator. The teeth
on the anti-kickback pawls point away from the workpiece.
If the workpiece should be pulled back toward the operator,
the teeth dig into the wood to help prevent or reduce the
possibility of kickback.
RIP FENCE - A sturdy metal fence guides the workpiece
and is secured with the locking lever. Grooves run along the
top and sides of the rip fence for use with optional clamps
and accessories.
BEVEL SCALE - The easy-to-read scale on the front of the
cabinet shows the exact blade angle.
BLADE - This saw is provided with a 36-tooth, 10 in. carbide-
tipped blade. The blade is raised and lowered with the
height/bevel adjusting handwheel. Bevel angles are locked
with the bevel locking lever.
SCALE - Located on the front rail, the easy-to-read scale
provides precise measurements for rip cuts.
SLIDING MITER TABLE - The sliding miter table moves
allowing the operator to slide the workpiece across the
saw table.
WARNING:
SLIDING TABLE EXTENSION - Located on the right side
of the saw table, this table extension gives the operator
additional support when cutting wide workpieces.
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
SPREADER - A metal piece of the blade guard assembly,
slightly thinner than the saw blade, which helps keep the
kerf open and prevent kickback.
BLADE GUARD - Always keep the blade guard down over
the saw blade for through-sawing cuts.
SWITCH ASSEMBLY - This saw has an easy access
power switch located below the front rail. To lock the switch
in the OFF position, remove the switch key from the switch.
Place the key in a location that is inaccessible to children
and others not qualified to use the tool.
BEVEL LOCKING LEVER - This lever, placed just under
the saw table surface on the front of the cabinet, locks the
angle setting of the blade.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
OPERATING COMPONENTS
WARNING:
The upper portion of the blade projects up through the table
and is surrounded by an insert called the throat plate. The
height of the blade is set with a handwheel on the front of
the cabinet. To accommodate wide panels, the saw table
has rails on each side. Detailed instructions are provided in
the Operation section of this manual for the basic cuts: cross
cuts, miter cuts, bevel cuts, and compound cuts.
Always remove the switch key when the tool is not in
use and keep it in a safe place. In the event of a power
failure, turn the switch OFF ( O ) and remove the key.
This action will prevent the tool from accidentally starting
when power returns.
The sliding miter table assembly is used for cross cutting
operations. The miter fence is easily adjusted to cut wood
at an angle by loosening the adjusting clamp, setting the
fence to the miter scale, and retightening the clamp. With
the miter fence removed, the miter table offers additional
support for other operations such as ripping.
WARNING:
ALWAYS make sure your workpiece is not in contact with
the blade before operating the switch to start the tool.
Failure to heed this warning may cause the workpiece to
be kicked back toward the operator and result in serious
personal injury.
The rip fence is used to position work for lengthwise cuts.
A scale on the front rail shows the distance between the rip
fence and the blade.
It is very important to use the blade guard assembly for
all through-sawing operations. The blade guard assembly
includes: riving knife/spreader/splitter, anti-kickback pawls,
and plastic blade guard.
WARNING:
To reduce the risk of accidental starting, ALWAYS make
sure the switch is in the OFF ( O ) position before plug-
ging tool into the power source.
SWITCH ASSEMBLY
This saw is equipped with a switch assembly that has a
built-in locking feature. This feature is intended to prevent
unauthorized and possible hazardous use by children and
others.
SWITCH
ON
SWITCH
OFF
TO TURN YOUR SAW ON:
With the switch key inserted into the switch, lift the switch
to turn ON ( l ).
TO TURN YOUR SAW OFF:
Press the switch down to turn OFF ( O ).
TO LOCK YOUR SAW:
Press the switch down.
Remove the switch key from the switch and store in a
safe, secure location.
SWITCH KEY
SWITCH IN LOCKED POSITION
Fig. 3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
BLADES
WARNING:
For maximum performance, it is recommended that you
use the 36-tooth, 10 in. carbide-tipped combination blade
provided with your saw. Additional blade styles of the same
high quality are available for specific operations such as
ripping. Your local dealer can provide you with complete
information.
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
TOOLS NEEDED
The following tools (not included) are needed for assembly and making adjustments:
FRAMING SQUARE
PHILLIPS
SCREWDRIVER
COMBINATION
FLATHEAD
SQUARE
SCREWDRIVER
Fig. 4
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS
The following items are included with your table saw:
B
C
A
H
D
E
G
F
I
Fig. 5
A. Rip Fence .................................................................................................................................................................... 1
B. Large Blade Wrench.................................................................................................................................................... 1
C. Small Blade Wrench.................................................................................................................................................... 1
D. Elbow .......................................................................................................................................................................... 1
E. Dust Bag ..................................................................................................................................................................... 1
F. Handle Assembly ........................................................................................................................................................ 1
G. Miter Fence with Lock Knob ....................................................................................................................................... 1
H. Blade Guard with Spreader and Anti-Kickback Pawls................................................................................................ 1
I. Hex Key....................................................................................................................................................................... 1
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
MOUNTING HOLES
UNPACKING
This tool comes mounted to a leg stand. If you chose to
remove the leg stand, the table saw must be mounted to a
firm supporting surface such as a workbench. Four bolt holes
have been provided in the saw’s base for this purpose. Each
of the four mounting holes should be bolted securely using
3/8 in. machine bolts, lock washers, and hex nuts (not in-
cluded). Bolts should be of sufficient length to accommodate
the saw base, lock washers, hex nuts, and the thickness of
the workbench. Tighten all four bolts securely.
This product requires assembly.
Carefully remove the tool and any accessories from the
box. Place it on a level work surface.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected the tool, identified all loose parts, and
satisfactorily operated the tool.
NOTE: Remove the foam block from between the
saw’s housing and the motor by first beveling the
blade (see page 23).
Carefully check the workbench after mounting to make
sure that no movement can occur during use. If any tipping,
sliding, or walking is noted, secure the workbench to the
floor before operating.
The saw is factory set for accurate cutting. After
assembling it, check for accuracy. If shipping has
influenced the settings, refer to specific procedures
explained in this manual.
If any parts are damaged or missing, please call 1-800-
525-2579 for assistance.
TO INSTALL THE HANDLE ASSEMBLY
See Figure 6.
Hold the nylon nut securely and turn the screw counter-
clockwise to remove the nut completely.
NOTE: Do not remove the screw from the handle or the
washer from the end of the screw.
WARNING:
If any parts are damaged or missing do not operate this
tool until the parts are replaced. Failure to heed this warn-
ing could result in serious personal injury.
Place the nylon nut into the recessed hole on the back
of the height/bevel adjusting handwheel and hold in
place.
Slide the handle, screw, and washer into the hole on the
height/bevel adjusting handwheel.
WARNING:
Using a flathead screwdriver, turn the screw clockwise
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
and tighten in place.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
SCREW
WARNING:
HANDLE
ASSEMBLY
Never stand directly in line with the blade or allow hands
to come closer than 3 in. to the blade. Do not reach over
or across the blade. Failure to heed this warning can
result in serious personal injury.
WASHER
NUT
HEIGHT/BEVEL
ADJUSTING HANDWHEEL
Fig. 6
WARNING:
To avoid serious personal injury, always make sure the
table saw is securely mounted to a workbench or an
approved leg stand. NEVER operate the saw on the
floor.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO OPEN/CLOSE (SET-UP/TEAR DOWN) THE
LEG STAND
See Figure 7.
SET-UP
TEAR DOWN
To open (set-up) the leg stand:
Step 1: With the saw table on end and standing to the side,
use your left hand to pull the leg stand latch towards you.
Step 2: Once the leg stand is released from the table saw
base, ease the legs of the stand down.
Steps 3 and 4: Grasp the upper leg support below the
saw cabinet. Keeping your left hand clear of the leg stand,
pull the leg stand up until it locks into place.
Step 5: With your left hand firmly on the table tilt handle,
grasp the leg stand with your right hand.
Steps 6 and 7: Push the leg stand towards the ground with
your right hand and pull in the same direction with your
left hand until the table saw is in an upright position.
To close (tear down) the leg stand:
Steps 1 and 2: Standing to the side of the table saw,
grasp the table tilt handle with your left hand. Tilt the table
saw to your left and grab the leg just below the leveling
foot.
Step 3: Lower the saw to the floor until it is balanced on
end.
Step 4: Using your left hand, release the leg stand
latch.
Steps 5 and 6: Once the leg stand is released from the
table saw base, ease the legs of the leg stand toward the
floor.
Step 7: Lift the lower leg of the leg stand until it locks in
place.
TO SECURE/LEVEL THE SAW
With the leg stand open and the table saw resting on a flat,
level surface, the saw should not move or rock from side
to side. If the saw rocks from side to side, the leveling foot
needs adjusting until the leg stand is balanced.
Turning clockwise will lower the foot.
Turning counterclockwise will raise the foot.
Fig. 7
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO STORE THE TABLE SAW ACCESSORIES
See Figures 8 - 9.
The table saw has two convenient storage areas (one on
either side of the saw cabinet) specifically designed for the
saw’s accessories.
When not in use, store the accessories securely by snapping
each accessory in place.
TO MOVE THE LEG STAND
See Figure 10.
RIP FENCE
Holding the leg stand firmly, pull the leg stand toward
you until the leg stand and saw are balanced on the
wheels.
STORAGE
HOOK
Push the saw to the desired location then either open the
leg stand for immediate saw operation or store the saw
in a dry environment.
TO REMOVE/REPLACE THE THROAT PLATE
See Figure 11.
Fig. 9
Lower the blade by turning the height/bevel adjusting
handwheel counterclockwise.
Loosen the screws in the throat plate.
Lift the throat plate from the saw.
To reinstall the throat plate, align the holes in the throat
plate with the holes in the saw table.
Retighten the screws, being careful not to overtighten,
which can cause the throat plate to bow or bend.
BLADE
WRENCHES
Fig. 10
SCREW
SAW TABLE
THROAT
PLATE
MITER
FENCE
STORAGE
HOOK
Fig. 8
Fig. 11
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO CHECK SAW BLADE INSTALLATION
See Figure 12.
LARGE
BLADE WRENCH
CAUTION:
To work properly, the saw blade teeth must point down
toward the front of the saw. Failure to do so could cause
damage to the saw blade, the saw, or the workpiece.
SMALL BLADE
WRENCH
NOTE: Arbor shaft has left hand threads.
Lower the saw blade and remove the throat plate.
Make sure the bevel locking lever is securely pushed to
the left. Raise the saw blade to its full height by turning
the height/bevel adjusting handwheel clockwise.
To loosen the blade:
Using the smaller blade wrench, place the flat open end
Fig. 12
on the flats on the arbor shaft.
Insert the closed end of the larger blade wrench over
the hex nut. Holding both wrenches firmly, pull the larger
wrench forward to the front of the machine.
LOCK
KNOB
MITER
FENCE
MITER
FENCE
HOLDER
To tighten the blade:
Using the smaller blade wrench, place the flat open end
MITER
INDICATOR
into the flats on the arbor shaft.
ATTACHMENT
Insert the closed end of the larger blade wrench over the
hex nut. Holding both wrenches firmly, push the larger
wrench to the back of the machine. Make sure the blade
nut is securely tightened. Do not overtighten.
BOLT
TABLE
SLOT
LOCATOR
PIN
Check all clearances for free blade rotation. See To Set the
Blade at 0˚ and 45˚ in the Adjustment section. In cutting
operations, the scale will be set to the side of the blade
where the cut will be measured and made.
TO INSTALL MITER FENCE
See Figure 13.
Remove the miter fence from the miter fence storage on
the side of the saw cabinet.
To install the miter fence to the sliding miter table, loosen
the lock knob so the bolt has enough clearance to slide
into the table slot.
QUICK STOPS
HOLE “A”
HOLE “B”
Fig. 13
Mount the miter fence to the miter table by installing the
locator pin (below the miter fence) into holes “A” or “B”.
At the same time, place the attachment bolt in the slot.
Properly adjust the miter indicator to the scale on the
end of the fence opposite the locator pin.
Retighten the lock knob.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
TO INSTALL BLADE GUARD ASSEMBLY
See Figure 14.
ANTI-KICKBACK
PAWLS
Proper installation of the blade guard assembly means that
the saw blade and spreader are in alignment. ALWAYS align
the spreader to the saw blade prior to turning on the table
saw.
Lower the blade.
Install the blade guard assembly to the mounting plate
using the wing nut. Partially retighten the wing nut. Check
the blade and spreader alignment.
SPREADER
WING
NUT
NOTE:Bladealignmentwiththespreadercanbeadjusted
for different blade widths. Refer to: To Check, and Align
theSpreader,SawBlade,andBladeGuardAssemblyin
the Adjustment section. Check the blade guard assembly
for clearances and free movement.
Tighten wing nut securely.
MOUNTING
PLATE
TO INSTALL DUST BAG
See Figure 15.
Fig. 14
Slide the elbow inside the dust chute on the back of the
DUST
CHUTE
table saw.
Slide the dust bag into the elbow.
NOTE: For efficient operation, empty the dust bag before it
is half full. This will permit better air flow through the bag.
ELBOW
DUST
BAG
Fig. 15
OPERATION
WARNING:
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating tools. Failure to do so could result
in objects being thrown into your eyes causing possible
serious injury.
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is suffi-
cient to inflict severe injury.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
AVOIDING KICKBACK
Always use the correct blade depth setting. The top of
the blade teeth should clear the workpiece by 1/8 in. to
1/4 in.
Inspect the work for knots or nails before beginning a
cut. Knock out any loose knots with a hammer. Never
saw into a loose knot or nail.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.
Always use the rip fence when rip cutting and the miter
fence when cross cutting. This helps prevent twisting the
wood in the cut.
WARNING:
Although many of the illustrations in this manual are
shown with the blade guard removed for clarity, do not
operate the saw without the blade guard unless specifi-
cally instructed to do so.
Always use clean, sharp, and properly-set blades. Never
make cuts with dull blades.
To avoid pinching the blade, support the work properly
before beginning a cut.
When making a cut, use steady, even pressure. Never
APPLICATIONS
You may use this tool for the purposes listed below:
force cuts.
Do not cut wet or warped lumber.
Straight line cutting operations such as cross cutting,
ripping, mitering, beveling, and compound cutting
Dado or molding cuts with optional accessories
Alwaysholdyourworkpiecefirmlywithbothhandsorwith
push sticks. Keep your body in a balanced position to
be ready to resist kickback should it occur. Never stand
directly in line with the blade.
Cabinet making and woodworking
NOTE: This table saw is designed to cut wood and wood
composition products only.
Use the right type of blade for the cut being made.
CUTTING AIDS
See Figure 16.
BASIC OPERATION OF THE TABLE SAW
The 3-prong plug must be plugged into a matching outlet
that is properly installed and grounded according to all local
codes and ordinances. Improper connection of the equip-
ment can result in electric shock. Do not modify the plug if
it will not fit the outlet. Have the correct outlet installed by
a qualified electrician. Refer to the Electrical section in this
manual.
Push sticks are devices used for safely pushing a workpiece
through the blade. They can be made in various sizes and
shapes from scrap wood and used in a specific project. The
stick must be narrower than the workpiece, with a 90˚ notch
in one end and shaping for a grip on the other end.
A push block has a handle fastened by recessed screws
from the underside. Use it on non-through cuts.
CAUSES OF KICKBACK
Kickback can occur when the blade stalls or binds, kicking
the workpiece back toward you with great force and speed. If
your hands are near the saw blade, they may be jerked loose
from the workpiece and may contact the blade. Kickback can
cause serious injury. Use precautions to avoid the risks.
CAUTION:
Be sure the screws in a push block are recessed to avoid
damaging the saw or workpiece.
Kickback can be caused by any action that pinches the
blade in the wood such as:
Making a cut with incorrect blade depth
Sawing into knots or nails in the workpiece
Twisting the wood while making a cut
Failing to support work
PUSH STICKS
Forcing a cut
Cutting warped or wet lumber
Using the wrong blade for the type of cut
Not following correct operating procedures
Misusing the saw
Failing to use the anti-kickback pawls
Cutting with a dull, gummed-up, or improperly set
PUSH BLOCKS
Fig. 16
blade
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TYPES OF CUTS
See Figure 17.
There are six basic cuts: 1) the cross cut, 2) the rip cut, 3) the
miter cut, 4) the bevel cross cut, 5) the bevel rip cut, and 6)
the compound (bevel) miter cut. All other cuts are combina-
tions of these basic six. Operating procedures for making
each kind of cut are given later in this section.
1
CROSS CUT
WARNING:
Always make sure the blade guard and anti-kickback
pawls are in place and working properly when making
these cuts to avoid possible injury.
2
3
4
RIP CUT
Cross cuts are straight 90° cuts made across the grain of
the workpiece. The wood is fed into the cut at a 90° angle
to the blade, and the blade is vertical.
Rip cuts are made with the grain of the wood. To avoid
kickback while making a rip cut, make sure one side of the
wood rides firmly against the rip fence.
MITER CUT
Miter cuts are made with the wood at any angle to the
blade other than 90°. The blade is vertical. Miter cuts tend
to “creep” during cutting. This can be controlled by holding
the workpiece securely against the miter fence.
WARNING:
Always use a push stick with small pieces of wood, and
also to finish the cut when ripping a long narrow piece
of wood, to prevent your hands from getting close to
the blade.
BEVEL CROSS CUT
5
6
Bevel cuts are made with an angled blade. Bevel cross cuts
are across the wood grain, and bevel rip cuts are with the
grain.
Compound (or bevel) miter cuts are made with an angled
blade on wood that is angled to the blade. Be thoroughly
familiar with making cross cuts, rip cuts, bevel cuts, and
miter cuts before trying a compound miter cut.
BEVEL RIP CUT
CUTTING TIPS
Dado and rabbet cuts are non-through cuts which can be
either rip cuts or cross cuts. Carefully read and understand
all sections of this operator’s manual before attempting any
operation.
COMPOUND (BEVEL) MITER CUT
Fig. 17
Make sure the kerf is made on the waste side of the
measuring line.
WARNING:
Cut the wood with the finish side up.
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
Knock out any loose knots with a hammer before making
the cut.
Always provide proper support for the wood as it comes
out of the saw.
The kerf (the cut made by the blade in the wood) will be
wider than the blade to avoid overheating or binding.
Make allowance for the kerf when measuring wood.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
featherboard. Positioning the featherboard will depend on
FEATHERBOARD
the placement of the bolt and the position of the sliding
miter table on the rails. Place the washer on the bolt and
attach the lock knob, loosely. Position the featherboard with
the hex head of the bolt in the miter table slot but do not
tighten. Completely lower the saw blade. Position the rip
fence to the desired adjustment for the cut to be performed
and lock. Place the workpiece against the fence and over the
saw blade area. Adjust the featherboard to apply resistance
to the workpiece just forward of the blade. Securely tighten
the lock knob to secure the featherboard in place. Attach a
C-clamp to further secure the featherboard to the edge of
the sliding miter table.
A featherboard is a device used to help control the
workpiece by guiding it securely against the table or fence.
Featherboards are especially useful when ripping small
workpieces and for completing non-through cuts. The end
is angled with a number of short kerfs to give a friction hold
on the workpiece and locked in place on the table with a
C-clamp. Test to ensure it can resist kickback.
WARNING:
Place the featherboard against the uncut portion of the
workpiece to avoid kickback that could cause serious
personal injury.
WARNING:
HOW TO MAKE A FEATHERBOARD
Do not locate the featherboard to the rear of the
workpiece. If positioned improperly, kickback can result
from the featherboard pinching the workpiece and bind-
ing the blade in the saw kerf. Failure to heed this warning
can result in serious personal injury.
See Figure 18.
The featherboard is an excellent project for the saw.
Select a solid piece of lumber approximately 3/4 in. thick,
3-5/8 in. wide and 18 in. long. Mark the center of the width
on one end of the stock. Miter one-half of the width to 30°
and miter the other half of the same end to 45° (see page
30 for information on miter cuts). Mark the board from the
point at 6 in., 8 in., 10 in., and 12 in. Drill a 3/8 in. hole at the
8 in., 10 in., and 12 in. marks.
PUSH BLOCK
PUSH STICK
FEATHERBOARD
Prepare the saw for ripping as discussed on page 29. Set
the rip fence to allow approximately a 1/4 in. “finger” to be
cut in the stock. Feed the stock only to the mark previously
made at 6 in. Turn the saw OFF and allow the blade to com-
pletely stop rotating before removing the stock. Reset the
rip fence and cut spaced rips into the workpiece to allow
approximately 1/4 in. fingers and 1/8 in. spaces between
the fingers.
BEVEL LOCKING
LEVER
HOW TO MOUNT A FEATHERBOARD
See Figure 19.
Remove the lock knob, bolt, and washer from the miter
fence holder. Place the bolt through one of the holes in the
Fig. 19
3/8 in. DIAMETER
30°
3-5/8 in.
1/4 in.
1-1/16 in.
45°
1/8 in.
6 in.
3/4 in.
8 in.
10 in.
12 in.
18 in.
Fig. 18
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO CHANGE BLADE DEPTH
See Figure 20.
GULLET
The blade depth should be set so that the outer points of
the blade are higher than the workpiece by approximately
1/8 in. to 1/4 in. but the lowest points (gullets) are below
the top surface.
Push the bevel locking lever down for elevation mode.
Raise the blade by turning the height/bevel adjusting
handwheel counterclockwise or lower it by turning the
handwheel clockwise.
TO CHANGE BLADE ANGLE (BEVEL)
See Figure 21.
Fig. 20
Push the bevel locking lever up for angle mode.
Toangletheblade, pushtheheight/beveladjustinghand-
wheel into the cabinet, to engage bevel gear, and turn
the handwheel until the bevel indicator shows the correct
angle.
ANGLED
BLADE
Push the bevel locking lever down to lock the angle, while
holding the height/bevel adjusting handwheel in place.
CHECKING SLIDING MITER TABLE AND
MAKING ADJUSTMENTS
TO POSITION THE SLIDING MITER TABLE
See Figures 22- 23.
A slide bolt is located on the front of the saw between the saw
table and the front scale. When the arrows on both the saw
table and sliding table are aligned, this bolt slides through
the holes in both tables locking them into a fixed position.
BEVEL
LOCKING
LEVER
BEVEL
INDICATOR
HEIGHT/BEVEL
ADJUSTING HANDWHEEL
The sliding table has three positions providing additional
front support when working with larger workpieces. Always
lock the sliding table when not in use.
Fig. 21
To unlock the sliding miter table:
Lift the tab on the slide bolt and move the bolt to the far
MITER
SLIDE LOCK
right.
Lock the bolt into position by pushing the tab down and
into the far right-hand notch.
To lock the sliding miter table:
Lift the tab and slide the bolt through both tables.
Lock the bolt into position by pushing the tab down and
into the notch.
NOTE: When moving the miter base, keep hands and
fingers out of areas where they may be pinched. Pull the
miter base into position with fingers extended and using
only your thumb as shown in figure 23.
SLOTS FOR LOCKING
MITER TABLE
Fig. 22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO CHECK MITER BASE PARALLELISM
See Figures 24 - 25.
Unplug the saw.
Setsawupasifyouwerepreparingtomakeacut. Tighten
rail clamps, miter locking clamps, lock knob, etc.
Slide miter table (A) to the front of miter base (B) as far
as it will go. Place a reference mark (C) near the end of
the miter table as shown in figure 24.
NOTE: Front of miter base is on infeed side of saw.
Place a reference mark on one of the blade teeth (D) and
rotate the blade (E) so that the reference mark on the
blade is at the front of the throat plate.
Place a framing square (G) against the blade and align
with reference mark on miter table. Measure the distance
between the blade and the edge of miter table.
Fig. 23
E
D
NOTE: Place framing square between carbide teeth and
measure from blade. This step will insure framing square
is square against blade from the front to back of blade.
Remove framing square and slide miter table to the rear
of miter base as far as it will go.
Rotate the blade so the reference mark on the blade is
at the rear of the throat plate. Measuring from the same
mark on the blade at the rear will eliminate the effect of
blade wobble.
A
C
Place framing square against the blade and align with
the same reference mark on the miter table. Measure the
distance between the blade and the edge of the miter
table at the rear.
Compare whether the front and rear measurements are
the same. If they are the same, proceed with checking
the miter fence alignment. If not, this indicates the miter
base needs aligning. Miter base must then be adjusted
before checking miter fence alignment. See To Adjust
the Miter Base section that follows.
G
Fig. 24
B
D
E
C
G
F
B
Fig. 25
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO ADJUST THE MITER BASE
SLIDING
MITER
TABLE
MITER
FENCE
ECCENTRIC
SCREW
See Figure 26.
Remember: Check all settings before loosening screws for
the following procedures. Once screws have been loosened,
these settings must be reset.
Unplug the saw.
Set the miter fence at 0˚ then securely tighten the
lock knob.
Push the sliding miter table to the back and loosen the
right-front screw from beneath the table saw cabinet.
Loosen the nylock nut beneath the front left eccentric
screw.
Placeonesideofaframingsquarefirmlyagainstthemiter
fence and the other side against the saw blade.
FRAMING
SQUARE
Using a flathead screwdriver, turn the eccentric screw
until the miter fence and the blade are square.
NYLOCK
NUT
Hold the eccentric screw in place with the screwdriver
and tighten the nylock nut securely.
Retighten the front right-hand screw.
TO CHECK MITER FENCE ALIGNMENT
RIGHT
FRONT
SCREW
See Figure 27.
The miter fence must be perpendicular to the blade when
set at zero degrees.
Set the miter fence (H) at 0°. Miter indicator (I) should be
set precisely on 0° and secured in place with adjusting
clamp (J).
NOTE: The quick-stop is not necessary for this checking
procedure. However, you may want to check and adjust it
to 0° at this time. See the To Adjust Quick-Stop section
that follows.
Fig. 26
E
G
Place a framing square (G) firmly against the miter fence
(H), with the other side against the blade (E).
J
Check whether the miter fence and blade are square with
each other. With the framing square against the miter
fence there should be no gap from the front to the rear
of the blade.
H
If a gap exists, the miter fence may be out of square.
Rotate the blade and recheck. If there is a consistent gap
between the front and rear of the blade, the miter table
needs aligning. Follow the adjustment procedures that
follow.
I
Fig. 27
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO ADJUST QUICK-STOP
See Figure 28.
The quick-stop is preset at the factory to stop the miter fence
at exactly 0°. However, when sliding miter table adjustments
are made, these adjustments may cause the quick-stop to
need adjusting. Check quick-stop with miter scale set at 0°. If
adjustments are needed, proceed with the following steps:
Loosen the eccentric screw holding the quick-stop.
Place the quick-stop against the miter fence with miter
QUICK
STOP
scale set at 0°.
Adjust eccentric screw until it holds quick-stop securely
against miter fence.
Retighten hex nut, securing eccentric screw and quick-
Fig. 28
stop.
Check your work. If the quick-stop is not at zero degrees,
RIP
FENCE
SCALE
repeat above steps.
BLADE
WARNING:
To reduce the risk of injury, always make sure the rip fence
is parallel to the blade before beginning any operation.
2 in.
TO SET THE RIP FENCE SCALE INDICATOR
TO THE BLADE
See Figure 29.
Begin with the blade at a zero angle (straight up).
Unplug the saw.
Loosen the rip fence by lifting the locking lever.
Using a framing square, set the rip fence 2 in. from the
blade tip edge.
FRONT
RAIL
SCALE
INDICATOR
LOCKING
LEVER
Loosen the screw on the scale indicator and align with
2 in.
MARK
the 2 in. mark as shown.
Fig. 29
Tighten the screw and check the dimension and the rip
fence.
LOCKING
LEVER
TO USE THE RIP FENCE
See Figure 30.
RIP FENCE
Place the rear lip on the rear of the saw table and pull
slightly toward the front of the unit.
Lower the front end of the rip fence onto the guide
SAW
TABLE
surfaces on top of the front rail.
Push the locking lever down to automatically align and
secure the fence.
Check for a smooth gliding action. If adjustments are needed,
see To Check the Alignment of the Rip Fence to the Blade
in the Adjustment section of this manual.
REAR LIP
Fig. 30
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO USE OUTFEED SUPPORT
See Figure 31.
The outfeed support slides to give the operator additional
support for cutting long workpieces.
With the table saw in the OFF position, stand behind the
saw.
Grasp the outfeed support with both hands and pull it
until it is fully extended.
OUTFEED
SUPPORT
TO USE THE TABLE EXTENSION
See Figure 32.
The table extension provides the operator with additional
table width for supporting wider workpieces.
To extend:
Push the table extension lever beneath the saw table
towards the back of the saw.
Fig. 31
Grasp the table extension with both hands and pull
it until the scale on the front rail indicates the desired
measurement.
Retighten the table extension lever by pulling it towards
the front of the saw.
To close:
Push the table extension lever beneath the saw table
towards the back of the saw.
Push the table extension with both hands back toward
the saw table.
Retighten the table extension lever by pulling it towards
TABLE
EXTENSION
LEVER
the front of the saw.
LOWER
SCALE
Fig. 32
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
HEELING (PARALLELING) THE BLADE
See Figures 33 - 35.
ADJUSTING
BOLTS (3)
(3)
(2)
WARNING:
(1)
The blade must be square so the wood does not bind
resulting in kickback. Failure to do so could result in
serious personal injury.
Do not loosen any bolts for this adjustment until you have
checked with a square and made test cuts to be sure adjust-
ments are necessary. Once the bolts are loosened, these
items must be reset.
FRAMING
SQUARE
Unplug the saw.
Lift the blade guard. Raise the blade all the way byturning
the height/bevel adjusting handwheel.
Markbesideoneofthebladeteethatthefrontoftheblade.
Place a framing square even with the front of the saw
table and the side of the saw blade as shown in figure 33.
Turn the blade so the marked tooth is at the back.
Move the framing square to the rear and again measure
the distance. If the distances are the same, the blade is
square.
If the distances are different, square the blade with the
following steps:
Fig. 33
Extend the extension table, see page 27.
FRAMING
SQUARE
Loosen adjusting bolts (1) and (3).
NOTE: The adjusting bolts are located above the height/
bevel adjusting handwheel and under the saw table in the
front of the saw.
Turn adjusting bolt (2) left or right until the blade is
square.
NOTE: If the back of the blade was too far from the fram-
ing square, place a block of wood on the left side of the
blade and push it into the blade until the blade is square.
Retighten the bolts.
If the back of the blade was too close to the framing
square, place a block of wood on the right side of the
blade and push it into the blade until the blade is square.
Retighten the bolts.
SAW BLADE OUT OF ALIGNMENT
Fig. 34
WARNING:
To reduce the risk of injury from kickback, align the rip
fence to the blade following any blade adjustments.
Always make sure the rip fence is parallel to the blade
before beginning any operation.
USE WOOD TO
PUSH THE BLADE
Fig. 35
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
MAKING CUTS
CROSS CUT
The blade provided with the saw is a high-quality combina-
tion blade suitable for ripping and cross cut operations.
PLACE LEFT HAND ON
WORKPIECE AND
MITER FENCE HERE
WARNING:
Do not use blades rated less than the speed of this tool.
Failure to heed this warning could result in personal
injury.
Use the miter fence when making cross, miter, bevel, and
compound miter cuts. To secure the angle, lock the miter
fence in place by twisting the lock knob clockwise. Always
tighten the lock knob securely in place before use.
NOTE: It is recommended that you place the piece to be
saved on the left side of the blade and that you make a test
cut on scrap wood first.
MAKING A CROSS CUT
See Figures 36 - 38.
WARNING:
Using the rip fence as a cutoff gauge when cross cutting
will result in kickback which can cause serious personal
injury.
Fig. 36
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
SWITCH
ON
SWITCH
OFF
It is recommended you make test cuts on scrap wood.
Remove the rip fence by lifting the locking handle.
Set the blade to the correct depth for the workpiece.
Set the miter fence to 0° and tighten the lock knob.
Place a support (the same height as saw table) behind
the saw for the cut work.
Make sure the wood is clear of the blade before turning
on the saw.
To turn the saw ON, lift the switch button.
SWITCH KEY
To turn saw OFF, press the switch button down.
NOTE: To prevent unauthorized use, remove the switch
key as shown in figure 37.
Let the blade build up to full speed before moving the
workpiece into the blade.
Hold the workpiece firmly with both hands on the miter
fence and feed the workpiece into the blade.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
SWITCH IN LOCKED POSITION
Fig. 37
29
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
MAKING A RIP CUT
See Figure 38.
RIP CUT
It is recommended you make a test cut on scrap wood.
RIP
FENCE
BLADE
WARNING:
SCALE
Make sure the blade guard assembly is installed and
working properly to avoid serious possible injury.
Position the rip fence the desired distance from the blade
for the cut and securely lock the handle. Adjust the scale
to zero at the cutting edge of the blade.
Place a support (the same height as saw table) behind
the saw for the cut work.
Make sure the wood is clear of the blade before turning
on the saw.
Use a push block or push stick to move the wood through
thecutpasttheblade.Neverpushasmallpieceofwood
intothebladewithyourhand;alwaysusea pushstick.
The use of push blocks, push sticks, and featherboards
are necessary when making non-through cuts.
Stand to the side of the wood as it contacts the blade to
reducethechanceofinjuryshouldkickbackoccur. Never
stand directly in the line of cut.
Make sure the wood is clear of the blade before turning
Fig. 38
on the saw.
Let the blade build up to full speed before feeding the
MITER CUT
workpiece into the blade.
BLADE
STRAIGHT
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
MAKING A MITER CUT
See Figure 39.
It is recommended you make test cuts on scrap wood.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
HEIGHT/BEVEL
ADJUSTING
HANDWHEEL
Remove the rip fence by lifting the locking handle.
MITER
FENCE
ANGLED
Set the miter fence to the desired angle and tighten the
lock knob.
Place a support (the same height as saw table) behind
the saw for the cut work.
Make sure the wood is clear of the blade before turning
on the saw.
Let the blade build up to full speed before moving the
workpiece into the blade.
Feed the workpiece into the blade until the cut has been
completed.
Fig. 39
30
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Position the workpiece flat on the table with the edge
MAKING A BEVEL CROSS CUT
flush against the rip fence. Let the blade build up to full
speed before feeding the workpiece into the blade.
Using a push stick and/or push blocks, slowly feed the
workpiece toward the blade. Stand slightly to the side of
the wood as it contacts the blade to reduce the chance
of injury should kickback occur.
See Figures 40 - 41.
It is recommended that you place the piece to be saved on
the left side of the blade and that you make a test cut on
scrap wood.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
VIEWED FROM THE FRONT, BELOW THE TABLE SAW
HEIGHT/BEVEL ADJUSTING
HANDWHEEL
Unlock the bevel locking lever.
Remove the rip fence by lifting the locking handle.
TO LOOSEN
Turn the height/bevel adjusting handwheel until the bevel
indicator is at the desired angle. Push the bevel locking
lever securely to the left to lock the angle.
Set the blade to the correct depth for the workpiece.
Set the miter fence to 90° and tighten the lock knob.
Place a support (the same height as saw table) behind
the saw for the cut work.
Make sure the wood is clear of the blade before turning
on the saw.
Let the saw blade build up to full speed before moving
the miter fence and the workpiece into the blade.
Hold the workpiece firmly with both hands on the miter
TO
TIGHTEN
fence and feed the workpiece into the blade.
BEVEL
LOCKING LEVER
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Fig. 40
BEVEL CROSS CUT
MAKING A BEVEL RIP CUT
See Figure 42.
BLADE
ANGLED
It is recommended you make test cuts on scrap wood.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid serious personal injury.
Remove the sliding miter fence.
Adjust the bevel angle to the desired setting.
Set the blade to the correct depth.
BEVEL LOCKING
LEVER
Position the rip fence the desired distance from the left
MITER
side of the blade and lock down the handle.
FENCE
STRAIGHT
If ripping a piece larger than 36 in. long, place a support
the same height as the table surface behind the saw for
the cut work.
Fig. 41
Turn the power switch to the ON position.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Once the blade has made contact with the workpiece,
BEVEL RIP CUT
use the hand closest to the rip fence to guide it. Make
sure the edge of the workpiece remains in solid contact
with both the rip fence and the surface of the table. If rip-
ping a narrow piece, use a push stick to move the piece
through the cut and past the blade.
BLADE
ANGLED
RIP
FENCE
SCALE
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Afterthebladehasstoppedcompletely,removethecutoff
stock.
Grasp the workpiece from the lead end (the end fed into
the blade first) and carefully remove it from the table.
MAKING A COMPOUND (BEVEL) MITER CUT
See Figure 43.
It is recommended that you place the piece to be saved
on the left side of the blade and that you make a test cut
on scrap wood first.
WARNING:
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
Remove the rip fence by lifting the locking handle.
Unlock the bevel locking lever.
Fig. 42
COMPOUND (BEVEL) MITER CUT
Adjust the bevel angle to the desired setting.
Lock the bevel locking lever.
PLACE RIGHT HAND
ON WORKPIECE AND
MITER FENCE HERE
Set the saw blade to the correct depth.
Loosen the lock knob on the miter fence, set the miter
fence to the desired angle and tighten the lock knob.
Turn the power switch to the ON position.
Position the workpiece flat on the table with the edge
flush against the miter fence. Let the blade build up to
full speed before feeding the workpiece into the blade.
Advance the workpiece and the miter fence toward the
blade. Keep the workpiece flush against the miter fence.
Push the miter fence and workpiece toward the blade.
Stand slightly to the side of the wood as it contacts the
blade to reduce the chance of injury should kickback
occur.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Afterthebladehasstoppedcompletely,removethecutoff
stock.
Fig. 43
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Raise the blade to the correct height by turning the
MAKING A LARGE PANEL CUT
See Figure 44.
height/bevel adjusting handwheel counterclockwise.
NOTE: Carefully check all setups and rotate the blade
one full revolution to assure proper clearance before
connecting saw to power source.
Make sure the saw is properly secured to a work surface to
avoid tipping from the weight of a large panel.
Plug in and turn on saw.
WARNING:
Feed the workpiece into the blade.
Make sure the blade guard assembly is installed and
working properly to avoid possible serious injury.
Always use push blocks, push sticks, and featherboards
whenmakingnon-throughcutstoavoidtheriskofserious
injury.
Place a support the same height as the top of the saw
table behind the saw for the cut work. Add supports to
the sides as needed.
WARNING:
Depending on the shape of the panel, use the rip fence
or miter fence. If the panel is too large to use either the
rip fence or the miter fence, it is too large for this saw.
When making a non-through cut, the cutter is covered
by the workpiece during most of the cut. Be alert to the
exposed cutter at the start and finish of every cut to avoid
the risk of personal injury.
WARNING:
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
Never make freehand cuts (cuts without the miter fence
or rip fence), which can result in serious injury.
Make sure the wood does not touch the blade before
you turn on the saw. Let the blade build up to full speed
before feeding the wood into the blade.
LARGE PANEL CUT
RIP FENCE
When the work is completed, press the switch off and
remove the key.
MAKING A NON-THROUGH CUT
See Figure 45.
Non-through cuts can be made with the grain (ripping) or
across the grain (cross cut). The use of a non-through cut is
essential to cutting grooves, rabbets, and dadoes.
SUPPORTS
NOTE: This is the only type cut that is made without
the blade guard installed. Make sure the blade guard
assembly is reinstalled upon completion of this type of
cut.
Read the appropriate section which describes the type of
cut in addition to this section on non-through or dado cuts.
For example, if your non-through cut is a straight cross
cut, read and understand the section on straight cross cuts
before proceeding.
HEIGHT
ADJUSTING
HANDWHEEL
Unplug the saw.
Fig. 44
Lower the blade.
Install the blade guard assembly to the mounting plate
using the wing nut. Partially retighten the wing nut. Check
the blade and spreader alignment.
Tighten wing nut securely.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
WARNING:
Never feed wood with your hands when making any
non-through cut such as rabbets or dadoes. To avoid
personal injury, always use push blocks, push sticks, or
featherboards.
Always use push blocks, push sticks, or featherboards
when making dado cuts to avoid the risk of serious
injury.
Unplug the saw.
NON-THROUGH CUT
BLADE
Lower the blade and remove the screw holding the throat
GUARD
plate in place. Remove the throat plate.
REMOVED
Raise the saw blade.
Pushthebevellockinglevertotheright.Rotatetheheight/
beveladjustinghandwheeluntilthebevelindicatorshows
a 30° angle. Push the bevel locking lever securely to the
left while holding the height/bevel adjusting handwheel
to lock the angle. Reinstall the blade guard assembly.
Retighten the nuts at the base of the spreader. Check
spreader alignment to the blade and adjust shims if
necessary.
PUSH
STICK
Move the bevel locking lever to the right and rotate the
blade back to 90°. Push the lever to the left to lock the
angle.
Lower the blade, insert the throat plate, then securely
tighten the throat plate screw.
MAKING A DADO CUT
See Figure 46.
An optional dado throat plate (part number 0134010313) is
required for this procedure. Do not use blades rated less
than the speed of this tool. This saw is designed for use
with a 6 in. stack dado (up to width of 5/8 in.). Do not use
an adjustable dado on this saw.
Fig. 45
DADO CUT
NOTE: This saw cannot be used to make a bevel dado
cut.
Unplug the saw.
Remove the blade guard assembly and the saw blade.
Mount the dado blade, using the blade and chippers
appropriate for the desired width of cut.
Reinstall the arbor nut.
Make sure the arbor nut is fully engaged and the arbor
extends at least one full thread past a securely tightened
arbor nut.
When mounting dado blades, make sure both the inner
blade washer and outer blade washer are used.
Install dado throat plate.
WARNING:
Always put all spacers in proper location when changing
back to saw blade. Failure to do so may result in possible
injury and damage to the tool.
Fig. 46
34
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
Rotate the blade by hand to make sure it turns freely.
Lower the saw blade and reinstall the throat plate.
WARNING:
NOTE: Securely tighten throat plate screws. Do not allow
the throat plate to bow up above the table surface.
Before performing any adjustment, make sure the tool is
unplugged from the power supply and the switch is in the
OFF position. Failure to heed this warning could result in
serious personal injury.
LARGE
BLADE WRENCH
WARNING:
Blades coast after turn off. Possible serious injury can
occur if hands come in contact with blade.
SMALL BLADE
WRENCH
The table saw has been adjusted at the factory for making
very accurate cuts. However, some of the components might
have been jarred out of alignment during shipping. Also,
over a period of time, readjustment will probably become
necessary due to wear.
Fig. 47
To avoid unnecessary set-ups and adjustments, a good prac-
tice is to check your setups carefully with a framing square
and make practice cuts in scrap wood before making finish
cuts in good workpieces. Do not start any adjustments until
you have checked with a square and made test cuts to be
sure adjustments are needed.
BLADE
WASHER
BLADE
ARBOR SHAFT
TO REPLACE THE BLADE
See Figures 47 - 49.
BLADE
NUT
Unplug the saw.
Lower the saw blade, raise the blade guard, and remove
the throat plate.
Make sure the bevel locking lever is securely pushed
down. Raise the saw blade to its full height by turning
the height/bevel adjusting handwheel clockwise.
Using the smaller blade wrench, insert the flat open end
into the flats on the arbor shaft.
Fig. 48
Insert the closed end of the larger blade wrench over
the hex nut. Holding both wrenches firmly, pull the larger
wrench forward to the front of the machine. Make sure
the blade nut is securely tightened. Do not overtighten.
SCREWS
THROAT
PLATE
NOTE: Arbor shaft has left hand threads.
Check all clearances for free blade rotation. See To Set the
Blade at 0˚ and 45˚. In cutting operations, the scale will be
set to the side of the blade where the cut will be measured
and made.
To replace the blade with an accessory blade, follow the
instructions provided with the accessory.
To install a standard blade:
Placethenewbladeonthearborshaft(theteethmustpoint
down toward the front of the saw to work properly).
BLADE
Place the blade washer and the blade nut over the blade
arbor. Be sure the dome side of the blade washer faces
out from the blade and that all items are snug against the
arbor housing. Tighten securely.
Fig. 49
35
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
TO CHECK AND ALIGN THE SPREADER, SAW
BLADE, AND BLADE GUARD ASSEMBLY
See Figure 50.
SCREW (2)
If the blade guard assembly is out of alignment with the saw
blade, adjust the alignment of the blade guard assembly. The
spreader must be aligned with the saw blade.
To check alignment of the spreader:
Unplug the saw.
FRAMING
SQUARE
Raise the saw blade by turning the height/bevel adjusting
handwheel counterclockwise.
Lift the anti-kickback pawls and place a framing square
or straight edge against both the saw blade and the
spreader.
The saw blade and spreader are aligned when the fram-
ing square contacts both the blade and spreader evenly
with no gaps.
If the spreader and saw blade are not in alignment,
adjustment is needed. To adjust:
Unplug the saw then raise the blade guard assembly.
Lift the anti-kickback pawls and place a framing square
or straight edge against both the saw blade and the
spreader.
From the back of the saw, loosen the two screws and
repositionthebladeguardassemblyleftorrightasneeded
to align the spreader with the saw blade.
Fig. 50
Once properly aligned, securely retighten the screws.
Recheck the marked blade tooth using the combination
RIP FENCE
square to insure the adjustment has not moved.
SCREWS
BLADE
TO CHECK THE ALIGNMENT OF THE RIP
FENCE TO THE BLADE
See Figure 51.
Unplug the saw.
Raise the locking lever to permit the rip fence to be
moved.
Place a framing square beside the blade and move the
rip fence up to the square. Take the dimension on the rip
scale.
LOCKING
LEVER
Move the fence back and turn the framing square 180°
to check the other side.
If the two dimensions are not the same, loosen the two
screws on the fence and align it.
FRAMING
SQUARE
Retighten the two screws.
Make two or three test cuts on scrap wood. If the cuts
are not true, repeat the process.
WARNING:
Before plugging the saw back in to make test cuts, make
sure the switch is in the OFF position and the blade guard
is in place. Failure to do so can result in serious injury.
Fig. 51
36
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
TO SET THE BLADE AT 0° AND 45°
BLADE
See Figures 52 - 53.
COMBINATION
SQUARE
0° ADJUSTMENT
The angle settings of your saw have been set at the factory
and, unless damaged in shipping, should not require set-
ting during assembly. After extensive use, they may need
to be checked.
BOLT
Raise the blade and the blade guard.
If the blade is not perfectly vertical (0°), loosen the adjust-
ment bolt and the bevel locking lever.
Place a combination square beside the blade on the left.
Lock the angle by pushing the bevel locking lever down
and retighten the adjustment bolt.
Turn the bevel handle until the bevel indicator points to
zero. If the bevel handle is turned as far as possible and
doesn't indicate zero properly, you may need to adjust
the bevel indicator.
BEVEL
LOCKING
LEVER
NOTE: It will be necessary to remove the bevel handle
to adjust the bevel indicator.
BEVEL
INDICATOR
BEVEL
HANDLE
If the blade is not an exact 45°, loosen the adjustment
Fig. 52
bolt and the bevel locking lever.
Turn the bevel handle until the bottom of the blade has
moved completely to the left side of the slot. Lock the
angle by pushing the bevel locking lever.
COMBINATION
SQUARE
BLADE
45° ADJUSTMENT
If the blade is not an exact 45°, loosen the 45° adjustment
45°
BOLT
bolt and the bevel locking lever.
Adjust the bevel indicator to 45°.
Make a test cut.
BEVEL
LOCKING
LEVER
BEVEL
INDICATOR
BEVEL
HANDLE
Fig. 53
37
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Periodically check all clamps, nuts, bolts, and screws for
tightness and condition. Make sure the throat plate is in
good condition and in position.
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
Check the blade guard assembly.
To maintain the table surfaces, fence, and rails, periodi-
cally apply paste wax to them and buff to provide smooth
functioning.
WARNING:
Protectthebladebycleaningoutsawdustfromunderneath
the table and in the blade teeth. Use a resin solvent on
the blade teeth.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
Clean plastic parts only with a soft damp cloth. DO
NOT use any aerosol or petroleum solvents.
GENERAL MAINTENANCE
LUBRICATION
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which may result in serious personal
injury.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Excess vibration.
Blade is out of balance.
Replace blade.
Blade is damaged.
Replace blade.
Saw is not mounted securely.
Work surface is uneven.
Tighten all hardware.
Reposition on flat surface.
Adjust legs of leg stand.
Blade is warped.
Check saw blade installation. Replace blade if
necessary.
Rip fence does not move
smoothly.
Rip fence not mounted correctly.
Rails are dirty or sticky.
Remount the rip fence.
Clean and wax rails.
Clamp screw is out of adjustment.
Adjust clamp screw counterclockwise.
Adjust clamp screw clockwise.
Rip fence does not lock at
rear.
Clamp screw is out of adjustment.
Replace or sharpen blade.
Slow the feed rate.
Cutting binds or burns work.
Blade is dull.
Work is fed too fast.
Wood is warped.
Replace the wood. Always cut with convex
side to table surface.
Check and adjust the rip fence.
Align the rip fence.
Rip fence is misaligned.
Wood edges away from rip
fence when ripping.
Blade not properly sharpened or set.
Resharpen or set blade.
See page 23 for adjustments to sliding
miter table assembly.
Sliding miter table assembly
does not move smoothly.
Miter base or slides improperly
adjusted.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Saw does not make accurate
90˚ or 45˚ cuts.
Positive stops inside cabinet need
adjusting (Bevel Cuts).
Adjust positive stops.
Adjust the miter fence.
Miter fence is misaligned (miter
cuts).
Height/bevel adjusting hand-
wheel is hard to turn.
Clean the gears or screw post.
Gears or screw post inside
cabinet are clogged with saw
dust.
Plug in motor cord or wall cord.
Motor cord or wall cord is not
plugged in.
Saw does not start.
Replace circuit fuse.
Reset circuit breaker.
Circuit fuse is blown.
Circuit breaker is tripped.
Cord or switch is damaged.
Have the cord or switch replaced at your
nearest authorized service center.
Blade makes poor cuts.
Clean, sharpen, or replace blade.
Replace with correct type.
Blade is dull or dirty.
Blade is wrong type for cut being
made.
Remount blade.
Blade is mounted backwards.
Move locking lever down.
Blade does not lower when
turning height/bevel adjusting
handwheel.
Locking lever is not at full down
position.
Motor labors in rip cut.
Blade not proper for rip cut.
Change blade; rip blade typically has fewer
teeth.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
41
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
10 in. TABLE SAW
BTS21
WARNING:
Somedustcreatedbypowersanding,sawing,grinding,drilling,andotherconstructionactivitiescontains
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
•lead from lead-based paints,
•crystalline silica from bricks and cement and other masonry products, and
•arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specially designed to filter out microscopic
particles.
• PARTS AND SERVICE
Prior to requesting service or purchasing replacement parts, please obtain your model
and serial number from the product data plate.
BTS21
• MODEL NUMBER
• SERIAL NUMBER
• HOW TO OBTAIN REPLACEMENT PARTS:
1-800-525-2579. Replacement parts can also be obtained at one of our Authorized
Service Centers.
• HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:
1-800-525-2579.
• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:
To obtain Customer or Technical Support please contact us at 1-800-525-2579.
RYOBI® is a registered trademark of Ryobi Limited used under license.
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Phone 1-800-525-2579
987000-087
1-18-07 (REV:00)
Download from Www.Somanuals.com. All Manuals Search And Download.
|