Rover Lawn Mower Domestic Rotary Lawnmower User Guide

DOMESTIC ROTARY LAWNMOWER  
OWNER’S MANUAL  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
Congratulations on your purchase of this domestic rotary lawnmower.  
This manual covers the setting up, operation and maintenance of the domestic  
rotary lawnmower. Please read and understand this owner’s manual before using the mower. If  
any point is unclear, contact Rover Mowers or any Rover Mowers authorized service dealer or  
agent.  
To emphasise special information the following WARNING and CAUTION highlights are  
used.  
WARNING  
CAUTION  
The safety of the user and  
others involved. Personal  
injury may result should this  
information be  
Follow these instructions  
to avoid mower damage  
and possible loss of  
warranty.  
disregarded.  
MANUAL CONTENTS  
Page  
·
·
Safety instructions  
1
2
3
Introduction  
·
Setting up  
·
Operation - All Models  
3, 4 & 5  
4 & 5  
- Mulch Models (only)  
·
Maintenance - All Models  
- Mulch Models (only)  
6, 7 & 8  
6, 7 & 8  
·
Mulch Mowing Information  
Warranty conditions  
8 & 9  
10  
·
CARTON CONTENTS:  
Quantity  
·
·
·
·
Domestic rotary lawnmower  
1
Plastic kit bag (containing Owner’s manuals and handle bar fasteners)  
1
1
1
Plastic grass catcher upper half  
Plastic grass catcher lower half  
NB. Mowers which have the Mulch option will have the mulch plug fitted into the rear chute of the  
mower.  
If when unpacking your new lawnmower it is found that there are items missing contact  
your nearest authorized Rover Mowers service dealer or agent.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING UP  
Plastic grass catcher assembly  
·
Refer to the “Set Up Instructions” attached to the grass catcher lower half.  
Grass Catcher  
Upper Half  
Grass Catcher  
Lower Half  
Figure 1. Grass Catcher—Assembled  
Engine oil  
Oil must be added before attempting to start the engine otherwise damage to the engine  
will occur.  
Refer to the engine owner’s manual.  
The 4 stroke engine fitted to the lawnmower is shipped with no oil in the sump.  
Engine fuel  
Refer to the engine owner’s manual.  
Use only fresh unleaded fuel in the lawnmower engine.  
OPERATION - All mowers  
Adjusting the cut height– refer figure 2.  
WARNING  
When selecting the cut height stand to the rear of the machine with your feet  
well clear of the cutting blades.  
(2)  
(1)  
The lawnmower 13 height settings are controlled by the  
height adjustment lever located at the rear right hand wheel.  
·
Grasp the height adjustment lever (1) and pull the lever  
away from the base to disengage the lever from the  
height adjustment rack (2).  
·
Move the lever either forwards or backwards to the  
desired position and release the lever so as to engage  
in the height adjustment rack.  
Figure 2. Height adjustment  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installing the grass catcher– refer figures 3 and 4.  
WARNING  
The grass catcher should only be fitted or removed when the engine is  
stopped. Never raise the rear flap when the engine is running.  
·
·
Raise the rear flap of the mower.  
Grasp the grass catcher by the top handle and position the grass catcher against the rear of  
the mower. Refer to Figure 3.  
·
Lower the rear flap so that the back edge of the rear flap hooks over the matching lip on the  
grass catcher. Refer to Figure 4.  
Rear Flap  
Figure 3. Grass catcher fitment  
Figure 4. Grass catcher fitted  
Removing the grass catcher  
·
·
Raise the rear flap of the mower to release the grass catcher.  
Lift the grass catcher clear of the mower and lower the rear flap.  
Emptying the grass catcher - refer figure 5.  
·
·
·
Remove the grass catcher (as per the instructions above).  
Tilt the grass catcher with the opening downwards.  
Grip the catcher handle of the grass catcher and shake the  
clippings out. Refer to figure 5.  
Figure 5. Emptying grass catcher  
OPERATION - Mulch Mowers (only)  
Installing the Mulch Plug  
WARNING  
The mulch plug should only be fitted or removed when the engine is stopped.  
Never raise the rear flap when the engine is running.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION - Mulch Mowers (only)  
Installing the Mulch Plug (Continued)  
·
·
With the engine stopped, raise the rear flap of the mower and remove the grass catcher (if fitted)  
Insert the long right hand side of the mulch plug first into the rear chute of the mower. Refer to  
figure 6.  
·
·
Rotate the left hand side into the rear chute of the mower and push it as far forward as possible.  
Align the lugs (1) (on the underside of the mulch plug) either side of the rear chute (2) then lower  
the mulch plug until it sits down flat onto the top of the rear chute in the mower base. Refer to  
figure 7.  
·
Lower the rear flap.  
(1)  
Figure 6. Mulch plug installation (A)  
Figure 7. Mulch plug installation (B)  
(2)  
Removing the Mulch Plug  
·
·
·
With the engine stopped, raise the rear flap of the mower.  
Grasp the rear of the mulch plug and lift up and away from the mower. Refer to figure 7.  
Guide the mulch plug out by rotating the shorter left hand side to the right and then guiding the  
longer right hand section until clear of the mower. Refer to figure 6.  
OPERATION - All mowers  
To Start the engine  
Refer to the engine owner’s manual for detailed starting procedure.  
Ensure that the engine oil is at the correct level and that the fuel tank is full of fresh unleaded fuel.  
To stop  
·
·
Move the throttle control lever to the :- “CHOKE”  
position (where fitted) - or the “FAST”  
position  
and prime the engine. Refer to the engine manual.  
Grasp rope handle and pull slowly until resistance is  
felt. Then pull the cord rapidly to overcome  
compression, prevent kickback and start engine.  
Repeat if necessary.  
·
If a “CHOKE”  
lever to the “FAST”  
starts.  
is fitted move the throttle control  
position after the engine  
Figure 8. Throttle Control -  
(“CHOKE” Position)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE - All mowers  
To Stop the engine  
Move the throttle control lever to the “STOP”  
position. Refer figure 8.  
Wait till the engine comes to a complete stop before removing or fitting the grass catcher or mulch  
plug to the mower, or attempting any maintenance work on the mower.  
WARNING  
Before carrying out any maintenance on the mower remove the spark plug lead  
from the spark plug to prevent accidental starting.  
Engine air cleaner  
Refer to the engine owner’s manual for detailed maintenance instructions.  
The engine air cleaner elements must be serviced after every 25 hours of normal mowing. The  
elements must be serviced more regularly if the mower is used in dusty conditions. Replace  
immediately if the element is damaged.  
Spark plug  
Refer to the engine owner’s manual for detailed maintenance instructions.  
For best results, remove the spark plug every 50 hours for gap checking and replace every 100  
hours of use. Replace the spark plug at any time if it is found that the electrodes are pitted or  
burned or the porcelain cracked. For replacement refer to engine owner’s manual for correct spark  
plug.  
Muffler  
Check the condition of the muffler periodically for rust and cracks. Replace if found to be damaged  
as this can lead to increased exhaust noise. Replace only with a genuine original equipment part.  
Blades - refer figure 9.  
Check the condition of the blades and central fasteners at regular intervals, or after striking a solid  
object, or if the mower begins to vibrate abnormally. The blades with use, will lose their sharp  
edge and the quality of the grass finish will deteriorate. When this happens, all the blades should  
be removed and replaced with a new set of blades. Always use genuine Rover replacement  
blades and only replace blades in sets to maintain balance.  
WARNING  
Always ensure the engine is stopped and the spark plug lead is removed before  
attempting any maintenance on the mower.  
Secure the mower safely when tilted upwards to access the underside.  
Cutting Assembly  
·
·
·
·
·
·
With the engine stopped, remove the spark plug lead and grass catcher or mulch plug.  
Set the height of cut lever to the high cut position, and fold the handle bars.  
Tilt the mower so the spark plug is up.  
Inspect the cutting assembly for damage and wear.  
Check the disc retaining bolts. Tighten the centre bolt to 57-62Nm.  
Return the mower to its normal position and re-attach the spark plug lead.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE - All mowers  
Blade Change- refer figures 9 and 10.  
WARNING  
Always ensure the engine is stopped and the spark plug lead is removed before  
attempting any maintenance on the mower.  
Always replace blades and blade fixings in complete sets to maintain balance.  
·
With the engine stopped, spark plug lead and grass  
catcher or mulch plug removed, open the discharge  
flap and prop in the open position. Refer to figure 9.  
Prop  
·
·
·
·
Set the mower to the high cut position and fold the  
handle bar down.  
Flap  
Rotate the cutting assembly carefully to access the  
blade retaining bolts. Refer to figure 10.  
Using gloves and a suitable spanner, remove the  
blade assembly.  
Retain the “D” plates and discard the blades and  
fasteners.  
Figure 9. Blade change  
NB. Mowers fitted with a circular cutting disc must be  
fitted with a “D” Plate (as shown in figure 10). These  
parts are available from any Rover Mowers authorized  
service dealer or agent.  
“D” plate  
·
Fit new blades and fasten in the correct order. Refer to  
figure 10.  
·
·
Tighten the blade retaining nuts firmly to 16Nm.  
Remove the flap prop, close the discharge flap and re-  
attach the spark plug lead.  
Figure 10. Blade Attachments  
Cleaning  
To ensure safe operation and long life it is recommended to clean the mower after every use. This  
will prevent corrosion, overheating and fire risk while ensuring ultimate performance.  
Washport (where fitted)  
·
·
·
Place the mower outdoors on a flat surface.  
Set the height to maximum.  
With the engine stopped connect a garden hose with a snap on  
connection, to the washport fitted to the inside face of the  
cutting chamber. Refer figure 11.  
·
·
Turn the garden hose on.  
Return to the mower and start the engine and run at full speed  
for 1 minute.  
·
·
·
Stop the engine and turn off the garden hose.  
Remove the garden hose from the washport.  
Figure 11. Washport Connection  
Inspect the underside of the mower, if not completely clean  
use garden hose to flush out remaining debris.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning the Underside of the Mower  
CAUTION  
Always ensure the engine is stopped and the spark plug lead is removed before  
attempting any maintenance on the mower.  
·
·
·
Place the mower outdoors on a flat surface.  
Set the cut height to maximum.  
With the engine stopped, remove the grass catcher or mulch plug and lift open the discharge  
flap.  
·
·
Use a garden hose to wash out all the grass clippings.  
Inspect the underside and repeat the cycle if still not clean.  
Cleaning the Upper side of the Mower  
CAUTION  
Do not hose the engine as water can damage the air cleaner and ignition system.  
·
·
·
Use a dry cloth or soft brush to remove all loose clippings.  
Use a damp cloth with mild detergent to clean away oil or other grime.  
Wash the grass catcher and/or mulch plug separately from the mower with a hose. Wash all  
clippings out of the inside, outside and from the grass catcher mesh.  
·
Let the mower dry before storing.  
MAINTENANCE - Mulch mowers (only)  
Mulching Equipment  
For optimum mulching performance  
·
·
·
·
·
The mulch blades are to be kept sharp.  
Maintain the blade sharpening angle when sharpening.  
Keep the cutting edge feather free when sharpening.  
Keep the underside of the mower deck and the mulch plug free of build-up.  
Refer to the “Cleaning” section on page 7 and 8.  
MULCH MOWING INFORMATION  
Some mowers are fitted with an option for mulch mowing.  
A mulch plug is supplied with these mowers and it is installed in the rear discharge chute (as  
noted in the “OPERATION” section of this manual) to perform mulch mowing.  
The following information provides advice on mulch mowing.  
MULCH MOWING  
The mulch mowing setup reduces the grass clippings into very fine particles.  
The design allows for the even distribution of the grass particles at the base of the lawn.  
The mulched clippings can then:  
·
·
·
·
Break down quickly, releasing nutrients into the soil, saving on fertilizer costs.  
Reduce evaporation of moisture from the soil which reduces watering costs and effort.  
Help to control temperature extremes protecting the roots of the grass.  
Assist in controlling soil erosion.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
MULCH MOWING INFORMATION (continued)  
BENEFITS TO YOUR LAWN  
Research has shown that lawns are usually cut too short,  
Grass, like any other plant life, relies on photosynthesis to regenerate and survive.  
Reduced leaf size (from cutting too low) can seriously effect a lawn by:  
·
·
·
Making it easy prey for disease.  
Encouraging weeds to take hold.  
Exposing the soil to:  
- greater evaporation  
- temperature extremes; and  
- erosion  
Raising the cut height and using mulch mowing follows the best practice for nurturing a healthier  
more attractive lawn with less water usage.  
BENEFITS FOR YOU  
Because you mulch as you mow the time and cost savings are also significant:  
·
Eliminating raking of leaves before mowing (Mulch mowing picks up and converts fallen  
leaves into mulch).  
·
·
·
·
Eliminating raking of cut grass  
Saves time spent emptying the catcher.  
Automatically disposing of grass clippings.  
Eliminating the need to dispose of clippings at the refuse tip.  
USEFUL MULCH MOWING TIPS  
Mulch mowing is an art form and to produce the best results consistently, follow these useful hints:  
·
·
·
·
·
Do not attempt to mulch if the grass is too wet.  
Wet grass tends to clump together and does not evenly spread out.  
It also clogs up the underside of the base.  
Do not mulch mow on too low a cutting height.  
Remember the maximum cut should be 25mm off the top of the grass, or 1/3rd the grass  
(blade) height, whichever is the lesser amount . Refer to figure 12.  
Do not push the mower too fast.  
To obtain the best finish it may be necessary  
to regulate the ground speed.  
Run the engine at full throttle.  
Running the engine at low speed does not  
allow the blades to mulch the grass efficiently.  
Keep the mulch blades sharp.  
The mulch blades are designed to cut and re-  
cut the blades of grass.  
If the mulch blades are not kept sharp,  
mulching performance will be reduced.  
Figure 12. Grass height  
·
Keep the underside of the mower and  
mulch plug clean.  
Build-up of grass under the mower base blocks the airflow created by the mulch blade and  
reduces the mulching performance.  
If the conditions for mulch mowing are not ideal and some clipping trails are visible after  
cutting it may be necessary to:  
1. Fit the grass catcher and catch mow.  
2. Re-mow over the visible clippings  
3. Raise the cut height.  
4. Rake the clippings up after mowing.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warranty Conditions  
Australia & New Zealand Only  
Rover Mowers Limited warrant that this machine is free from defects in material and workmanship.  
This warranty is limited to making good or replacing any part which appears upon inspection by  
the manufacturer or his agent to be defective in material or workmanship.  
The warranty for the engine used to power this machine may differ from the warranty for the other  
components. Refer to the engine warranty statement in the Engine Owner’s Manual which has  
been included with this machine. As the warranty may differ, you are advised to read the engine  
warranty carefully.  
For other items this warranty shall apply for a period of 12 months from date of purchase for  
domestic use only. However these items are not warranted for commercial or industrial use.  
This warranty does not obligate the manufacturer, his agents or dealers to bear the transport costs  
incurred in the repair or replacement of any defective part. This warranty excludes fair wear and  
tear, or any damage caused by misuse or abuse. Parts such as blades, blade bolts, V-belts, and  
spark plugs, which can be subjected to use beyond their normal intended working capacity are  
also excluded.  
This warranty is void if parts other than genuine have been used or if repairs or alterations have  
been made without the manufacturer’s written authority. The above warranty does not exclude any  
condition or warranty implied by the Trade Practices Act 1974 or any other relevant  
legislation which implies any condition which cannot be excluded.  
REMEMBER:  
PROOF OF PURCHASE IS THE RESPONSIBILITY OF THE OWNER AND IS RECOMMENDED  
PRIOR TO WARRANTY WORK BEING UNDERTAKEN. REPAIRS MUST BE CARRIED OUT  
BY AN AUTHORISED DEALER OR AGENT AND GENUINE SPARE PARTS MUST BE USED  
OR YOUR WARRANTY WILL BE VOID.  
Rover Mowers Limited reserves the right to make changes and add improvements to its product at any time  
without notice or obligation. The Company also reserves the right to discontinue manufacture of any product at  
its discretion at any time.  
Online warranty registration:  
For your Record:  
Retailers Name: .............................................Address: .......................................................... .........  
Phone No: ......................................................Model No: ...................................................... ..........  
Serial No: .......................................................Date of Purchase: ............................................ ........  
A.B.N. 11 000 257 303  
Rover Mowers Limited, PO. Box 1235, Eagle Farm. Qld. Australia. 4009  
Phone: 07 3213 0233  
04016593  
Revision  
© Copyright  
2008  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q See Medical Alarms QSD9004 User Guide
Radio Shack Answering Machine TAD 739 User Guide
Radio Shack Cell Phone TAD 723 User Guide
Radio Shack Surge Protector 61 2341 User Guide
Rosewill Network Router RNX 56USB User Guide
Rotel Stereo Receiver RT 935AX User Guide
Russell Hobbs Microwave Oven RHM1708 G User Guide
Sanyo Refrigerator MPR 1013 User Guide
Sanyo Universal Remote RCS BH80AABWL User Guide
SEAL Laminator AS 1600 User Guide