®ÂØÒňΙ
Workshop
The Sounds of the Fantom-X
© 2005 Roland Corporation U.S.
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of Roland Corporation U.S.
FXWS02
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting Patches on the Fantom-X
Looking for Patches
In this section, we’ll talk about selecting a patch for the
Fantom-X keyboard. While there are a few ways to locate a
patch you want, the first step is to let the Fantom-X know that
it’s a keyboard patch you’re after.
To search for a patch to use, press F1 (Patch List)—a screen like
the one shown here appears.
Normally you select a patch for the keyboard and a rhythm set for the pads.
However, you can turn this around if you like. If you select a rhythm set for
the keyboard, each key plays a different drum/percussion sound. If you
select a patch for the pads, each pad plays the patch at a different pitch. For
now, though, we’ll presume you want to play a patch on the keyboard.
Press PATCH/RHYTHM to display the Patch Play screen, and
then press F7 (Kbd) to select the keyboard.
Search by Category
The Patch List screen is configured by default to present you
the available patches arranged by musical category, as you
can see along the left side of the screen. Most of the time, this
provides a sensible, easy way to locate a patch.
If you don’t see category names listed at the left, press F4 (Patch Categ).
Here’s how to select patches by category from the patch list:
You can select patches on the Patch Play screen by highlighting
the patch number—as shown above—or bank name, and then
turning the VALUE dial. (We’ll explain banks in a few pages).
•
•
Press F2 (↓) or F1 (↑) to select the category you want.
Once the desired category is selected, press 5 or 6 or
turn the VALUE dial to select a patch.
•
•
You can try out the patch by playing the keyboard, or by
pressing and holding F7 (Preview) to hear a brief passage
that demonstrates the selected patch.
When you’ve got the patch you want, press F8 (Select) to
confirm your choice and exit the patch list.
More typically, though, you’ll either be:
•
•
looking for a patch you want to use, or
selecting a known, favorite patch.
We’ll discuss these two different operations separately. In the
next sections, we’ll assume you’re on the Patch Play screen.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing patches in banks is handy when a patch’s location—
on a memory card or expansion board, for example— makes it
easy to find. It’s also a great way to quickly play your samples.
Search by Location
Press F5 (Patch) to view your patches sorted according to their
locations in the Fantom-X’s memory.
Select the desired patch as we described on Page 4.
Selecting Favorite Patches
The Fantom-X has an even faster way of selecting patches you
use over and over. You can designate 64 patches as “favorites”
that can be selected using the eight F buttons. Each bank of
favorites puts another eight patches at your fingertips.
Adding a Patch to Your Favorites List
There are two ways to add—or “register”—a Favorite patch.
Fantom-X patches are actually stored in groups, or“banks.”You
can see the banks listed along the left side of the screen:
Quickly Add a Patch from the Patch Play Screen
•
USER—This bank contains 256 memory locations in which
you can store your own patches, or edits of the factory
patches.
1. After selecting the patch on the Patch Play screen, press F2
(Favorite) to display the Favorite Patch window.
•
•
•
•
Preset-A through Preset-I—Preset Banks A-I hold the 1,152
Fantom-X factory patches.
GM—These two banks appear as one continuous bank
holding the 256 General MIDI and General MIDI 2 sounds.
CARD—This bank contains any Fantom-X patches you’ve
saved to an installed PC memory card.
User Sample, Card Sample—These banks allow you to
directly select and play samples in user or card memory
using the Auto Patch feature described in the Sampling on
the Fantom-X Workshop booklet.
2. Turn VALUE to select the desired Favorites bank.
3. Hold down SHIFT and press the F1-F8 button you’d like to
use for selecting the patch in the future.
•
XP-A through XP-D—When you’ve installed an SRX Series
wave expansion board, its patches show up in the XP (for
“expansion”) memory area corresponding to the SRX slot
in which you’ve installed the board.
4. Press EXIT to return to the Patch Play screen.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Add a Patch Directly from the Patch List
Exploring the Fantom-X Patches
1. On the Patch List screen, press F3 (Favorite) to display the
Favorite Patch window.
Now that we’ve discussed the ways in which you can easily get
to any of the many patches, we thought we’d point out a few
patches that show off the Fantom-X’s range.
We recommend finding these patches by category from the Patch List
screen for now. Make sure to press F4 (Patch Categ) on the Patch List screen
to display patches by musical category.
Patch
Category
Take a moment to...
UltimatGrand
AC. Piano
play up and down the keyboard,
varying your touch to hear the
patch’s expressiveness.
The VorteX
Synth FX
Strings
listen to the sheer complexity of
this patch.
2. Press F2 (↓) or F1 (↑) to select the desired Favorites bank.
3. Press 6 or 5 to select the desired location for the patch
within the selected Favorites bank.
4. Press F6 (Regist) to add the patch as a new favorite.
X StrSection
check out the rich realism of this
string patch by playing lines and
chords. (Keep your foot off the
Hold pedal for best results.)
Removing a Patch from the Favorites List
FlamencoGt X
HimalayaPipe
Strobot
AC. Guitar
Flute
play some tender guitar licks. Slap
hard for a quick hammer-on.
In the Favorite Patch window, select the patch you want to
remove from the list, and press F5 (Remove).
play this haunting, ethereal patch
slowly, letting the sound unfold.
Selecting a Patch from Your Favorites List
Pulsating
throb in time with this rave patch.
Press PATCH/RHYTHM if you’re not already on the Patch
Play screen, and then press F2 (Favorite)—your first bank of
Favorite patches appears. To select a different Favorites bank,
turn the VALUE dial.
You can see that each of the Favorite patches has an F button
name printed to its left—press the desired patch’s F button to
select the patch.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
The realtime controllers allow you to manipulate the sound of
the currently selected patch or effect as you play, responding
in realtime to your actions. To try this out:
Realtime Controllers
The Fantom-X boasts an assortment of realtime controllers:
•
The Pitch Bend/Modulation lever—
Push the lever forward to turn up
the current patch’s LFO. Push it left
or right to bend the pitch of notes
down or up, respectively.
The keyboard itself—You can use
“aftertouch” to control sounds by
pressing down into the keyboard.
1. Select the Square Sphere patch in the Pulsating category.
2. Press the D Beam ASSIGNABLE button so it’s lit.
3. Press the REALTIME CONTROL button repeatedly—with
each press, the functions of the REALTIME CONTROL knobs
change, as shown on the display.
•
•
The REALTIME CONTROL knobs (circled in red below)—By
turning the knobs, you can:
4. Play the patch and experiment with how the D Beam and
REALTIME CONTROL knobs change the sound as you play.
•
•
•
adjust a patch’s filter and envelope settings.
adjust arpeggiator and rhythm generator settings.
change the values of patch or effect parameters.
As you operate a realtime control, you’re changing the value
of one or more parameters in the patch or in the patch’s effect.
We’ll explain how to set up assignable realtime control later.
Piano Mode
The Fantom-X offers a special Piano mode that provides the
ultimate acoustic or electric piano-playing experience. When
you press PIANO MODE so it lights, the Fantom-X display
presents you unique options for the creation of the most
realistic, expressive piano sounds.
•
•
The two ASSIGNABLE SW buttons (circled in yellow above)—
Press the buttons to turn settings on or off, or transpose
the keyboard up and/or down by semitones.
The D Beam—Move your hand up or down
above the D Beam lenses to:
•
•
•
trigger pads.
play notes using a mono synth sound.
change the values of patch or effect
parameters.
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Piano mode opens up by default with the Fantom-X’s
extraordinary 88-note multisampled piano. You can, if you
wish, select other acoustic piano patches, or select an electric
piano patch.
simulates the way in which a real piano’s strings cause
its neighboring strings to vibrate in sympathy, creating a
piano’s characteristic resonance. You can set the desired
amount of resonance.
•
If you’re on the acoustic piano screen—you can highlight the
current patch’s name and turn VALUE to select a different
acoustic piano.
To adjust a parameter, press the corresponding F button, and
the parameter’s window pops open onscreen. To close the
window, press the F button again.
•
If you’re on the electric piano screen—you can highlight the
current patch’s name and turn VALUE to select a different
electric piano.
GM (General MIDI) acoustic and electric piano patches cannot be selected
in Piano mode.
To switch between piano types, press F1 (List), and then:
•
•
•
Press F1 (AC. Piano) or F2 (El. Piano).
Turn the VALUE dial to select the desired patch.
Press F8 (Select) to confirm your choice.
Electric Pianos in Piano Mode
In Piano mode, the acoustic and electric piano screens offer
their own unique options.
Acoustic Pianos in Piano Mode
With an acoustic piano in Piano mode, you can set:
•
•
•
KeyTouch—ThisparameteradjuststheFantom-X’sresponse
to the force with which you hit the keys in Piano mode.
Select the value that best reflects your playing style.
Open Close—As you raise or lower a real grand piano’s lid,
the piano’s sound changes. Use the Open Close parameter
to set the height of the virtual Fantom-X piano’s lid.
Resonance—When you play an acoustic piano in Piano
mode, the Fantom-X multi-effects are automatically set
to use Effect 78, Sympathetic Resonance. This effect
When you’re playing an electric piano, you can set the electric
piano’s Key Touch (explained above), and turn on an effect
typically used for electric piano.
ꢆ
Download from Www.Somanuals.com. All Manuals Search And Download.
You can turn on:
There are two kinds of recordings a Fantom-X patch can play.
It can play:
•
•
•
•
•
Tremolo—This effect causes notes to swing side-to-side,
left-to-right, as in classic Stage-model electric pianos.
Chorus—Chorus adds the shimmering effect so commonly
applied to electric pianos.
Phaser—Funky electric pianos often use phasing that adds
a whooshing swirl to the sound.
EQ—EQ allows you to brighten-up or smooth out an
electric piano sound to taste.
•
built-in recordings—The Fantom-X contains 1,436 brief
sound recordings stored as PCM “waveforms.” When you
install an SRX Series wave expansion board, you add even
more waveforms from which patches can be built.
•
your own recordings—A patch can also play recordings, or
“samples,” you’ve captured yourself on the Fantom-X, or
that you’ve imported via USB. These may be brief chunks of
sound, like the built-in waves, or complete performances.
Speaker Simulator—This effect helps recreate the sound of
vintage electric piano speakers.
When you sample something on the Fantom-X, it’s a patch or rhythm set
that plays it. See the Sampling on the Fantom-X Workshop booklet for more
on sampling.
To turn on and customize an effect, press its F button—the F
button lights onscreen and its parameters are displayed. You
can adjust the displayed parameters using the REALTIME
CONTROL knobs. Each parameter is numbered to show the
knob that controls it.
Tones: The Structure of a Patch
Each patch is a set of
four sound-producing
devices called“tones.”It’s
the tones that actually
play the recordings that
make up a patch.
1BUDI
For a detailed explanation of the electric piano parameters, see the Effect
List section of your Owner’s Manual, starting on Page 270.
5POF
ꢀ
5POF
ꢀ
How a Patch Works
5POF
ꢁ
If you want to edit patches or create your own, you’ll need
to understand what makes a patch tick, so to speak. In this
section, we’ll discuss the mechanics of a patch.
Each tone can play:
5POF
ꢂ
•
a stereo waveform or
sample, or
•
two mono waveforms or samples.
Where Does a Patch Get Its Sound?
A patch may or may not use all four of its tones, depending on the
complexity of the sound its programmer is trying to achieve.
Each Fantom-X patch is actually a group of one or more audio
recordings playing back together as a single sound. There are
lots of settings in a patch that control how the recordings play
and interact—the Fantom-X effects contribute significantly to
a patch’s sound, too—but everything starts with this group of
recordings.
A tone doesn’t have to play a stereo waveform or sample, or two mono
waveforms or samples—it can play a single mono waveform or sample
if you like.
ꢇ
Download from Www.Somanuals.com. All Manuals Search And Download.
Each tone has its own set of about 90 parameters that
determine how its waveforms or samples play. Tones can be
set to play together in different ways, resulting in a variety of
different sounds from the same basic sonic materials.
Getting the Right Tones
Since a patch is made up of its tones, a key element in patch
programming is choosing the right waves or samples for its
tones to play.
In addition, there are parameters that control the behavior of
the combined sound produced by the patch’s active tones.
A patch’s effect plays a large role in its final sound, too. To learn more about
effects, check out the Workshop booklet The Fantom-X Effects.
Making Your Own Patches
If you’re tweaking an existing patch—or you’re editing a patch
that plays samples you’ve made—the tones you want are most
likely already in place. When you’re creating a new patch from
scratch, though, the first thing you’ll want to do is figure out
how many tones you really want to use. Many patches sound
great with just one or two tones. There’s no need to use all four
available tones unless each one really contributes to the sound
you want—there’s no point in doing programming work for
no reason, after all. And there’s another reason to keep your
patches lean, as you’ll learn in the following section.
After you’ve read the following sections and are ready to get started, see
Page 56 in the Owner’s Manual for some helpful patch-programming tips.
Inthisbooklet, wediscussediting—andthereforecreating—patchesonthe
Fantom-X itself. If you prefer, you can accomplish the same thing on your
computer using the Fantom-X Editor (and Librarian) software.
To get to a patch’s parameters, select the patch on the Patch
Play screen, and then press PATCH EDIT.
You can create a new patch from one of your samples by selecting it from
the patch list’s User or Card Sample bank, and then pressing PATCH EDIT.
About Tones and Polyphony
Every synth or sampler has a maximum number of waveforms
or samples it can play at a single time. This limit is referred to as
the instrument’s “available polyphony,” and each note played
by a waveform or sample is called a “voice” in this context.
Each stereo waveform or sample a tone plays uses two voices,
one for its left side, and one for the right. Likewise, a tone
uses two voices when it plays two mono waves or tones. The
more tones a patch uses, the more voices of polyphony it
eats up. With four tones active, a patch can use eight voices
of polyphony for each note you play. If you play a three-note
chord, you’d be using 24 voices—if you play two chords with
the sustain pedal down, you’d be using 48 voices!
You may find it helpful to compare your edits against the last-saved version
of the current patch as you work. See Page 60 in the Owner’s Manual.
ꢈ
Download from Www.Somanuals.com. All Manuals Search And Download.
Since the Fantom-X can play a whopping 128 voices at once,
you’re unlikely to have any problems playing patches in Patch
mode. When you’re using multiple patches during recording,
however, you may notice notes not playing in passages with
lots of dense instrumentation. If this occurs, check the patches
you’re using and see if you can live without any of their tones.
The Four Graphic Editing Screens
The Owner’s Manual—starting on Page 60—provides more details than
we can here, but the following brief descriptions will get you started.
The Pitch Env Edit Screen
Use the Pitch Env—for “Pitch Envelope”—Edit screen’s
parameters to automate changes to a tone’s pitch as a note
plays, as described on Page 68 in the Owner’s Manual.
You can easily see how many voices you’re using at any time. Press PATCH/
RHYTHM, LAYER/SPLIT or MIXER, and then hold down SHIFT and press F4
(Voice Monitor) to view a graphic display of the voices currently in use.
Activating and Selecting Tones
To turn tones on or off on a patch editing screen, press F8
(Tone Sw/Sel) to show the Tone Switch/Select F buttons.
•
•
To turn each of the four possible tones on or off—press the
desired F1-F4 button. When a tone’s on, it lights yellow.
To edit a tone’s parameters—press the corresponding F5-
F8 button. When a tone’s selected for editing, it turns
red onscreen. To edit the parameters of multiple tones
simultaneously, press their F buttons at the same time.
The TVF Edit Screen
The TVF—for “Time Variant Filter”—can remove selected
frequency ranges from a tone’s waveform or sample, as
described on Page 69 in the Owner’s Manual.
To hide the Tone Sw and Tone Select buttons, press EXIT.
Editing a Tone’s Parameters
When you press PATCH EDIT, the Fantom-X offers a set of
screens that let you literally see the effect of each edit you
make.
You can adjust important parameter values on the graphic editing screens
using the four REALTIME CONTROL knobs.
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
The TVF Envelope Edit Screen
The Structure Edit Screen
The TVF Envelope Edit screen allows you to automate changes
to a tone’s frequency content as a note plays, as described on
Page 71 in the Owner’s Manual.
On the Structure Edit screen, you can set the relationship
between the patch’s tones—this can have a major impact
on the patch’s sound. See Page 63 in the Owner’s Manual for
more.
The TVA Env Edit Screen
The Patch Overview Screen
The TVA Env—for “Time Variant Amplifier” envelope—Edit
screen allows you to automatically shape a tone’s volume as a
note plays, as explained on Page 72 in the Owner’s Manual.
The Patch Overview screen provides quick access to the most
commonly used tone parameters. Use F2 (↓) or F1 (↑) to move
from section to section, and the REALTIME CONTROL knobs to
adjust parameter values in the currently selected section.
The Structure Edit and Patch Overview Screens
There are two additional graphic editing screens you can
display by pressing F5 repeatedly.
To learn about the LFO parameters, see Page 74 in the Owner’s Manual.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
•
TVF (Time Variant Filter)—The Time Variant Filter can
remove selected frequency ranges from a tone’s waveform
or sample. Set the properties and basic behavior of the
filter here. See Page 69 in the Owner’s Manual.
TVF Env (TVF Envelope)—The TVF envelope allows you to
automate changes to a tone’s frequency content as a note
plays. See Page 71 in the Owner’s Manual.
TVA (Time Variant Amplifier)—The TVA parameters set the
basic volume behavior of a tone, and set its panning. See
Page 71 in the Owner’s Manual.
TVA Env (TVA Envelope)—The TVA envelope allows you to
automatically shape a tone’s volume as a note plays. See
Page 72 in the Owner’s Manual.
Output—The Output parameters determine where a tone’s
sound goes: to effects or directly to selected physical
outputs. You can set the amount of the tone to be sent to
the desired effects. See Page 73 in the Owner’s Manual.
LFO 1, LFO 2—LFOs provide repeating, cyclical changes
to the desired parameter values, such as pitch, panning
and more. Each tone has two standard LFOs that can be
configured as desired. See Page 74 in the Owner’s Manual.
Step LFO—The step LFO allows you to set up more complex
repeating changes than a standard LFO. See Page 76 in the
Owner’s Manual.
Solo/Porta (Portamento)—These parameters determine
whether the entire patch plays only one note at a time or
multiple simultaneous notes, and sets the way in which
one note moves to the next. Portamento, or note sliding,
is also controlled by this group of settings. See Page 77 in
the Owner’s Manual.
The Pro Edit Parameters
For detailed editing, the Fantom-X offers Pro Edit mode’s
Patch Edit screen, in which all patch-wide and tone-specific
parameters are arranged in sections from top to bottom on
the display. To move from section to section, press F2 (↓) or
F1 (↑). To edit a parameter within the selected section, press
5 or 6 to highlight it and turn VALUE to adjust its setting.
•
•
•
•
To enter Pro Edit mode, press F6 (Pro Edit) on a graphic editing
screen. To return to graphic editing, press F6 (Zoom Edit) on
the Patch Edit screen.
What The Parameter Sections Do
•
General—These parameters apply to the patch as a whole.
It’s where you sets its musical category, overall level and
panning, and set the patch’s importance to you when
polyphony is at its limit. You can adjust its tuning and
response, and do some overall tweaking to a few key
parameters. See Page 60 in the Owner’s Manual for more.
•
•
•
Wave—These parameters allow you to select each tone’s
PCM wavesform(s) or sample(s), and set their basic
behavior. See Page 62 in the Owner’s Manual.
TMT (Tone Mix Table)—Set the manner in which the active
tones interact here. Also, control the basic volume and
playback characteristics of a tone with these settings. See
Page 63 in the Owner’s Manual.
•
•
•
•
Pitch—Set a tone’s basic tuning here, and how it responds
to the Pitch Bend/Modulation lever, as well as to the pitch
envelope, below. See Page 67 in the Owner’s Manual.
Pitch Env (Pitch Envelope)—The pitch envelope allows you
to automate changes to a tone’s pitch as a note plays. See
Page 68 in the Owner’s Manual.
•
Misc—These miscellaneous parameters allow you to delay
the start of a tone as you play, and to set a tone’s response
to certain MIDI messages. See Page 78 in the Owner’s
Manual.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
•
CTRL 1, 2, 3, 4—These parameters constitute the patch’s
“matrix control” area. Matrix control lets you use a variety
of devices, including MIDI messages, to alter patch
parameter values as notes play. Each of the four CTRL
screens lets you select a controlling device, or“source,”and
up to four parameters, or “destinations,” for manipulation.
Sources can be controllers transmitted from the REALTIME
CONTROL knobs, as explained in the next section.
The Patch Edit Utility Menu
On the Patch Edit screen, press F4 (Util Menu) to display the
Utility menu.
To perform one of the Utility menu operations, highlight it
using the VALUE dial or 6 or 5, and then press F8 (Select).
Programming the REALTIME CONTROL Knobs
To program the behavior of the REALTIME CONTROL knobs
when their ASSIGNABLE LED is lit:
Copying Tone Settings
1. Hold down SHIFT and turn any of the knobs—the Control
Setting screen appears, where you can set each of the four
knobs to transmit the desired type of MIDI message.
If you’d like to copy the settings from one tone to another
within the same patch—or even “borrow” the settings of a
tone from another patch—use the Tone Copy feature. In the
Utility menu, select Patch Tone Copy.
In the Patch Tone Copy window, you can select the tone you
want to copy (the Source patch and tone) and to where you
want to copy it (the Destination patch and tone).
Press F2 (↓) or F1 (↑) to display and set the assignable behavior of the D
Beams and ASSIGNABLE SW buttons.
To audition the copy source patch, press F6 (Compare) so the Compare
button lights red.
2. When you’re done, press F8 (System Write)—in Patch
mode, realtime control settings are stored in system
memory. (In Performance mode, each performance has its
own realtime control settings.)
When you’re ready, press F8 (Exec) to make the copy.
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Initializing a Patch
Saving New or Edited Patches
If you’d like to start a patch from total scratch by setting all of
the current patch’s parameters to their default values, you can
“initialize” it using the Utility menu’s Patch Initialize operation.
Whether you’ve been editing an existing patch or creating a
new one, store your work in the Fantom-X’s memory before
selecting another patch or powering off to avoid losing your
work. To do so, “write” the patch. Here’s how.
Don’t worry about running a saved patch by initializing it—you’re only
resetting the parameters belonging to a copy of the patch currently in the
Fantom-X’s edit memory. You can save this copy to a new memory location
as described in “Saving New or Edited Patches” in the next column.
Start by pressing WRITE—the Write Menu screen
appears, ready to store your patch since you’re
coming from a patch-editing screen.
The Patch Edit Msmpl Edit Button
The Patch Edit screen’s F5 (Msmpl Edit)—for “Multisample
Edit”—button allows you to map out a group of samples
up and down the keyboard. To learn about working on the
Multisample Edit screen, see the Sampling on the Fantom-X
Workshop booklet.
Final Touches
Once you’ve got your new patch’s parameters the way you
want them, take a little time to program the patch’s effect. The
Fantom-X effects add a lot to the sound of a patch.
If “Patch/Rhythm” isn’t highlighted at the top of the screen,
press F2 (Patch/Rhythm). If it is, you can press ENTER instead
if you like.
If you plan to use your patch in a recording on the Fantom-X,
don’t worry about any slight changes you may need to make
to the patch so it fits perfectly in your arrangement. Recording
work takes place in Performance mode, where you can tweak
many patch parameters while hearing the patch in context.
Be sure to save your patch to user or card memory when you’re done, as
described next.
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
To name a patch:
Selecting Patches Remotely Via MIDI
1. The first character position is underlined, so turn VALUE to
select the first character of the patch’s name.
2. Press 4 to move the underline to the next character’s
position, and turn VALUE to select the second character.
3. Repeat Step 2 to enter the characters of the patch name
you want.
Since the Fantom-X has such extraordinary sounds, you may
want to use it with an external sequencer, such as one you’d
run on a computer. You can easily select Fantom-X sounds
directly from a sequencing program by transmitting the
appropriate MIDI messages on the MIDI channel for the
Fantom-X’s keyboard or pads in Patch mode, or the patch’s
part channel in Performance mode.
As you name the patch, you can:
See Page 230 in the Owner’s Manual to learn about the Kbd and Pad Patch
TX/RX Channel parameters in Patch mode. Performance Parts 1-16 receive
MIDI messages on MIDI Channels 1-16, respectively, by default.
•
•
•
Press F1 (Change Type) repeatedly to jump between
upper-case, lower-case and numeric characters.
Press F2 (Delete) to remove the character at the underline’s
current location.
Press F3 (Insert) to insert a blank space in which you can
enter a new character at the underline’s current location.
To select a patch via MIDI, send the Fantom-X the appropriate
Bank Select MSB and LSB values, and Program Change value.
These values are listed in the following chart.
The XP groups in the following chart depend on the SRX boards you’ve
installed. See each installed board’s Owner’s Manual.
When you’ve finished naming the patch, press F8 (Write). The
Patch Write window pops up:
1. Use F3 (↓) and/or F2 (↑) to select the Fantom-X’s internal
user memory as the location in which the patch is to be
saved, or to select Card if you’ve installed a memory card.
2. Turn VALUE to select the user or card location in which
you’d like to store the patch, and then press F8 (Write) to
store the patch.
Patch Bank Select and Program Change Chart
Group
USER
CARD
Number
Bank Select
MSB LSB
Program
Number
1-128
1-128
1-128
1-128
1-128
1-128
1-128
1-128
1-128
001-128
129-256
001-128
129-256
001-128
001-128
001-128
001-128
001-128
87
87
0
1
If there’s already a patch in the selected location, and you’d like to audition
it before replacing it with a new patch, press F4 (Compare) so it turns red.
As long as Compare is on, you can try out patches to see which one you
want to replace. To turn off Compare, press F4 (Compare) again.
87
32
33
64
65
66
67
68
87
PR-A
PR-B
PR-C
PR-D
PR-E
87
87
87
87
87
Don’t worry about replacing one of the factory user patches. They’re all
copies of preset patches permanently stored in your Fantom-X.
3. The Fantom-X asks if you’re sure you want to proceed.
Press F8 (Exec) to finish storing the patch.
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
The End
Group
Number
Bank Select
Program
Number
1-128
MSB
LSB
69
We hope you’ve enjoyed this introduction to the amazing
PR-F
001-128
001-128
001-128
001-128
001-256
001-256
001-2000
001-7000
001-
001-
:
87
87
87
87
121
87
64
65
93
93
:
sounds of the Fantom-X. Check out the other Fantom-X
Workshop booklets, as well your Fantom-X Handbook, Owner’s
Manual, and the Audio Track Expansion guide. We’re confident
you’ll have a great time with the exciting, inspiring Fantom-X.
PR-G
70
1-128
PR-H
71
1-128
PR-I
72
1-128
For the latest Fantom-X updates and support tools, visit the Roland U.S.
amazing Product Support team at 323-890-3745.
GM (2)
0-4
32, 33
0-14
(see patch list)
1-128
CARD
USER SAMPLE
CARD SAMPLE
1-128
0-53; 54 1-128; 1-88
XP-A
XP-B
XP-C
XP-D
SRX-01
SRX-02
:
0
1
:
1-
1-
:
SRX-01
SRX-02
:
001-
001-
:
93
93
:
0
1
:
1-
1-
:
SRX-01
SRX-02
:
001-
001-
:
93
93
:
0
1
:
1-
1-
:
SRX-01
SRX-02
:
001-
001-
:
93
93
:
0
1
:
1-
1-
:
ꢀꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
|