Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s manual
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” (p. 4) and “IMPORTANT NOTES” (p. 7).
These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its
entirety. The manual should be saved and kept on hand as a convenient reference.
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of
ROLAND CORPORATION.
Roland is registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
About WARNING and CAUTION Notices
About the Symbols
The symbol alerts the user to important instructions or
Used for instructions intended to alert the user
to the risk of death or severe injury should the
unit be used improperly.
warnings.The specific meaning of the symbol is determined by
the design contained within the triangle. In the case of the
symbol at left, it is used for general cautions, warnings, or alerts
to danger.
Used for instructions intended to alert the user
to the risk of injury or material damage should
the unit be used improperly.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must not be
done is indicated by the design contained within the circle. In
the case of the symbol at left, it means that the unit must never
be disassembled.
* Material damage refers to damage or other
adverse effects caused with respect to the
home and all its furnishings, as well to
domestic animals or pets.
The symbol alerts the user to things that must be carried
out. The specific thing that must be done is indicated by the
design contained within the circle. In the case of the symbol at
left, it means that the power-cord plug must be unplugged
from the outlet.
ALWAYS OBSERVE THE FOLLOWING
002c
007
●
Do not open (or modify in any way) the unit or
its AC adaptor.
●
Make sure you always have the unit placed so it
is level and sure to remain stable. Never place it
on stands that could wobble, or on inclined
surfaces.
......................................................................................................................
......................................................................................................................
003
●
008c
●
Do not attempt to repair the unit, or replace
parts within it (except when this manual
provides specific instructions directing you to
do so). Refer all servicing to your retailer, the
nearest Roland Service Center, or an authorized
Roland distributor, as listed on the separate
sheet titled “Information.”
Be sure to use only the AC adaptor supplied with
the unit. Also, make sure the line voltage at the
installation matches the input voltage specified
on the AC adaptor’s body. Other AC adaptors
may use a different polarity, or be designed for a
different voltage, so their use could result in
damage, malfunction, or electric shock.
......................................................................................................................
004
●
......................................................................................................................
Never install the unit in any of the following
locations.
❍ Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a
heating duct, on top of heat-generating
equipment); or are
❍ Damp (e.g., baths, washrooms, on wet floors);
or are
❍ Exposed to steam or smoke; or are
❍ Subject to salt exposure; or are
❍ Humid; or are
008e
●
Use only the attached power-supply cord. Also,
the supplied power cord must not be used with
any other device.
......................................................................................................................
009
●
Do not excessively twist or bend the power
cord, nor place heavy objects on it. Doing so can
damage the cord, producing severed elements
and short circuits. Damaged cords are fire and
shock hazards!
❍ Exposed to rain; or are
❍ Dusty or sandy; or are
❍ Subject to high levels of vibration and shakiness.
......................................................................................................................
......................................................................................................................
4
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
010
●
015
●
This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate
for a long period of time at a high volume level,
or at a level that is uncomfortable. If you
experience any hearing loss or ringing in the
ears, you should immediately stop using the
unit, and consult an audiologist.
Do not force the unit’s power-supply cord to
share an outlet with an unreasonable number of
other devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power
rating (watts/amperes) for the extension cord.
Excessive loads can cause the insulation on the
cord to heat up and eventually melt through.
......................................................................................................................
......................................................................................................................
011
016
●
Do not allow any objects (e.g., flammable
material, coins, pins); or liquids of any kind
(water, soft drinks, etc.) to penetrate the unit.
●
Before using the unit in a foreign country,
consult with your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the separate sheet titled
“Information.”
......................................................................................................................
019
●
Batteries must never be recharged, heated,
taken apart, or thrown into fire or water.
......................................................................................................................
012b kai
●
If you encounter any of the following
circumstances, immediately switch off the
power and disconnect the AC adaptor (if one is
being used) from the power outlet. And request
servicing by your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the separate sheet titled
“Information” when:
......................................................................................................................
027
●
Never expose Battery to excessive heat such as
sunshine, fire or the like.
❍ The AC adaptor, the power-supply cord, or
the plug has been damaged; or
❍ If smoke or unusual odor occurs
❍ Objects have fallen into, or liquid has been
spilled onto the unit; or
......................................................................................................................
❍ The unit has been exposed to rain (or
otherwise has become wet); or
❍ The unit does not appear to operate
normally or exhibits a marked change in
performance.
101b
●
The unit and the AC adaptor should be located
so their location or position does not interfere
with their proper ventilation.
......................................................................................................................
013
●
In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for
the safe operation of the unit.
......................................................................................................................
102c
●
......................................................................................................................
Always grasp only the plug on the AC adaptor
cord when plugging into, or unplugging from,
an outlet or this unit.
014
●
Protect the unit from strong impact.
(Do not drop it!)
......................................................................................................................
......................................................................................................................
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
103b
111: Selection
●
At regular intervals, you should unplug the AC
adaptor and clean it by using a dry cloth to wipe
all dust and other accumulations away from its
prongs. Also, disconnect the power plug from
the power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug
and the power outlet can result in poor
●
If used improperly, batteries may explode or
leak and cause damage or injury. In the interest
of safety, please read and observe the following
precautions (p. 20).
❍ Carefully follow the installation instructions
for batteries, and make sure you observe the
correct polarity.
❍ Avoid using new batteries together with
used ones. In addition, avoid mixing
different types of batteries.
❍ Remove the batteries whenever the unit is to
remain unused for an extended period of
time.
1
2
3
5
insulation and lead to fire.
......................................................................................................................
104
●
Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
❍ If a battery has leaked, use a soft piece of
cloth or paper towel to wipe all remnants of
the discharge from the battery
......................................................................................................................
compartment. Then install new batteries. To
avoid inflammation of the skin, make sure
that none of the battery discharge gets onto
your hands or skin. Exercise the utmost
caution so that none of the discharge gets
near your eyes. Immediately rinse the
affected area with running water if any of the
discharge has entered the eyes.
106
●
Never climb on top of, nor place heavy objects
on the unit.
......................................................................................................................
107c
●
Never handle the AC adaptor or its plugs with
wet hands when plugging into, or unplugging
from, an outlet or this unit.
6
❍ Never keep batteries together with metallic
objects such as ballpoint pens, necklaces,
hairpins, etc.
......................................................................................................................
112
●
......................................................................................................................
Used batteries must be disposed of in
compliance with whatever regulations for their
safe disposal that may be observed in the region
in which you live.
108b
●
Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
......................................................................................................................
......................................................................................................................
118a
109b
●
Should you remove the ground terminal screw,
keep them in a safe place out of children’s reach,
so there is no chance of them being swallowed
accidentally.
●
Before cleaning the unit, turn off the power and
unplug the AC adaptor from the outlet (p. 20).
......................................................................................................................
......................................................................................................................
120
110b
●
Always turn the phantom power off when
connecting any device other than condenser
microphones that require phantom power. You
risk causing damage if you mistakenly supply
phantom power to dynamic microphones,
audio playback devices, or other devices that
don’t require such power. Be sure to check the
specifications of any microphone you intend to
use by referring to the manual that came with
it.
●
Whenever you suspect the possibility of
lightning in your area, disconnect the AC
adaptor from the outlet.
......................................................................................................................
(This instrument’s phantom power: 48 V DC,
10 mA Max)
......................................................................................................................
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
360
Power Supply: Use of Batteries
●
Depending on the material and temperature of the surface on
which you place the unit, its rubber feet may discolor or mar
the surface.
You can place a piece of felt or cloth under the rubber feet to
prevent this from happening. If you do so, please make sure
that the unit will not slip or move accidentally.
301
●
Do not connect this unit to same electrical outlet that is being
used by an electrical appliance that is controlled by an
inverter (such as a refrigerator, washing machine, microwave
oven, or air conditioner), or that contains a motor. Depending
on the way in which the electrical appliance is used, power
supply noise may cause this unit to malfunction or may
produce audible noise. If it is not practical to use a separate
electrical outlet, connect a power supply noise filter between
this unit and the electrical outlet.
Maintenance
401a
●
For everyday cleaning, use a soft, dry cloth (such as those used
to clean eyeglasses) to wipe the unit clean. If dust or dirt has
settled on the surface, we recommend that you gently dust off
the unit before you wipe it, since dust particles can act like an
abrasive and scratch the unit‘s surface if you wipe it without
clearing away the dust first. For stubborn dirt, use a cloth
dampened with mild detergent. Note that some detergents
may contain solvents; make sure that the detergent you use
does not contain a solvent.
302
●
The AC adaptor will begin to generate heat after long hours of
consecutive use. This is normal, and is not a cause for concern.
304a
●
When installing or replacing batteries, always turn off the
power on this unit and disconnect any other devices you may
have connected. This way, you can prevent malfunction and/
or damage to speakers or other devices.
402
●
307
●
Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions and/or
damage to speakers or other devices.
Repairs and Data
452
●
Placement
Please be aware that all data contained in the unit’s memory
may be lost when the unit is sent for repairs. Important data
should always be backed up on a USB memory, or written
down on paper (when possible). During repairs, due care is
taken to avoid the loss of data. However, in certain cases (such
as when circuitry related to memory itself is out of order), we
regret that it may not be possible to restore the data, and
Roland assumes no liability concerning such loss of data.
351
●
Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum. To
alleviate the problem, change the orientation of this unit; or
move it farther away from the source of interference.
352a
●
This device may interfere with radio and television reception.
Do not use this device in the vicinity of such receivers.
352b
●
Noise may be produced if wireless communications devices,
such as cell phones, are operated in the vicinity of this unit.
Such noise could occur when receiving or initiating a call, or
while conversing. Should you experience such problems, you
should relocate such wireless devices so they are at a greater
distance from this unit, or switch them off.
Additional Precautions
551
●
Please be aware that the contents of memory can be
irretrievably lost as a result of a malfunction, or the improper
operation of the unit. To protect yourself against the risk of
loosing important data, we recommend that you periodically
save a backup copy of important data you have stored in the
unit’s memory on a USB memory.
354a
●
Do not expose the unit to direct sunlight, place it near devices
that radiate heat, leave it inside an enclosed vehicle, or
otherwise subject it to temperature extremes. Excessive heat
can deform or discolor the unit.
552
●
Unfortunately, it may be impossible to restore the contents of
data that was stored in the unit’s memory once it has been
lost. Roland Corporation assumes no liability concerning such
loss of data.
355b
●
When moved from one location to another where the
temperature and/or humidity is very different, water droplets
(condensation) may form inside the unit. Damage or
malfunction may result if you attempt to use the unit in this
condition. Therefore, before using the unit, you must allow it
to stand for several hours, until the condensation has
completely evaporated.
553
●
Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
554
●
Never strike or apply strong pressure to the display.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
556
❍ Do not touch or allow metal to come into contact with the
contact portion of the cards.
●
When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you will
avoid causing shorts, or damage to the cable's internal
elements.
❍ Do not bend, drop, or subject cards to strong shock or
vibration.
❍ Do not keep cards in direct sunlight, in closed vehicles, or
other such locations.
558a
●
To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about those
around you (especially when it is late at night).
❍ Do not allow cards to become wet.
❍ Do not disassemble or modify the cards.
559a
●
Copyright
When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise, you
will need to use equivalent packaging materials.
852a
●
This product can be used to record or duplicate audio or visual
material without being limited by certain technological copy-
protection measures. This is due to the fact that this product is
intended to be used for the purpose of producing original
music or video material, and is therefore designed so that
material that does not infringe copyrights belonging to others
(for example, your own original works) can be recorded or
duplicated freely.
562
●
Some connection cables contain resistors. Do not use cables
that incorporate resistors for connecting to this unit. The use
of such cables can cause the sound level to be extremely low,
or impossible to hear. For information on cable specifications,
contact the manufacturer of the cable.
563
●
Unauthorized duplication, reproduction, hiring, and lending
prohibited.
853
●
Do not use this unit for purposes that could infringe on a
copyright held by a third party. We assume no responsibility
whatsoever with regard to any infringements of third-party
copyrights arising through your use of this unit.
564
●
Before you open the included DVD-ROM, you must read the
“license agreement.” Opening the DVD-ROM will be taken to
mean your acceptance of the license agreement.
203
*
204
*
Before Using USB Memories
GS (
) is a registered trademark of Roland Corporation.
Microsoft, Windows and Windows Vista are registered
trademarks of Microsoft Corporation.
Using USB Memories
704
●
206e
Carefully insert the USB memory all the way in—until it is
firmly in place.
*
The screen shots in this document are used in compliance
with the guidelines of the Microsoft Corporation.
206j
*
Windows® is known officially as: “Microsoft® Windows®
operating system.”
207
*
209
*
Apple and Macintosh are registered trademarks of Apple Inc.
Mac OS is a trademark of Apple Inc.
220
*
All product names mentioned in this document are trademarks
or registered trademarks of their respective owners.
238
*
MPEG Layer-3 audio compression technology is licensed from
Fraunhofer IIS Corporation and THOMSON Multimedia
Corporation.
USB Memories
add
*
705
MMP (Moore Microprocessor Portfolio) refers to a patent
portfolio concerned with microprocessor architecture, which
was developed by Technology Properties Limited (TPL).
Roland has licensed this technology from the TPL Group.
●
Never touch the terminals of the USB memory. Also, avoid
getting the terminals dirty.
708
●
USB memories are constructed using precision components;
handle the cards carefully, paying particular note to the
following.
add
*
MatrixQuest™ 2007 TEPCO UQUEST, LTD. All
rights reserved. The SD-50‘s USB functionality
uses Matrix-Quest middleware technology from
TEPCOUQUEST, LTD.
❍ To prevent damage to the cards from static electricity, be
sure to discharge any static electricity from your own body
before handling the cards.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES...........................................................................................7
Side Panel........................................................................................................................................................................... 18
Using Bus Power............................................................................................................................................... 21
Turning the Power Off.................................................................................................................................... 22
Mac OS X Users................................................................................................................................................................. 33
Playing Back the Sample Data..................................................................................................................... 39
Using Playlist Editor........................................................................................40
Installing Playlist Editor ................................................................................................................................................. 40
Windows 7 / Windows Vista users.............................................................................................................. 40
Windows XP Users ........................................................................................................................................... 40
Mac OS X Users.................................................................................................................................................. 40
Creating a Playlist............................................................................................................................................................ 41
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Getting Ready to Record ............................................................................................................................... 56
Recording............................................................................................................................................................ 57
Input/Output and Effect Settings.............................................................................................................................. 59
Using the SD-50 as a MIDI Interface...............................................................60
Changing the Tempo...................................................................................................................................... 68
Changing the Key............................................................................................................................................. 68
Using Minus-One and Center Cancel (MINUS ONE/CENTER CANCEL).......................................... 69
Selecting Favorite Songs (FAVORITE)....................................................................................................................... 70
Registering a Favorite Song ......................................................................................................................... 70
Selecting a Favorite Song.............................................................................................................................. 70
Adjusting the Input/Output Volume........................................................................................................................ 71
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
System Settings...............................................................................................72
Basic Procedure for System Settings........................................................................................................................ 72
Utility Functions ..............................................................................................74
Backing Up User Data (BACKUP)................................................................................................................. 75
Formatting USB Memory (USB MEM FORMAT) ..................................................................................... 76
Returning to the Factory Settings (FACTORY RESET).......................................................................... 77
Reinstalling the Driver....................................................................................86
Settings Saved as User Data.........................................................................105
Solo Tone .......................................................................................................106
MIDI Implementation Chart .........................................................................108
Specifications ................................................................................................109
Index...............................................................................................................111
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Check the Contents of the Package
When you open the package, check that all items are present. If anything is missing, please contact your dealer.
❏
SD-50 (main unit)
❏
❏
SD-50 Owner’s Manual (the document you’re reading)
This explains how to use the SD-50, and includes cautions and other notes. Keep it at hand for reference.
Software Disc (DVD-ROM)
This disc contains the following.
•
•
•
SONAR LE (music production application software)
Playlist Editor (application software for managing songs)
SD-50 driver
*
Do not touch the data surface (unprinted surface) of the disc. Doing so might make the data unreadable.
If the disc gets dirty, clean it using a commercially available disc cleaner.
❏
❏
AC adaptor (with power cord)
This is a dedicated AC adaptor for the SD-50. You must use only the supplied adaptor.
USB cable
This cable connects the SD-50 to your computer’s USB connector.
*
Please use the included USB cable. If you need a replacement because the included USB cable becomes damaged, please contact
one of the service locations listed at the back of this manual.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
Front Panel
fig.panel-front_e.eps
2
3
4
5
1
10
6
7
9
8
11 12 13 14
15 16 17 18
19 20
*
If you continue playing even when the indicator is
blinking, the display will indicate “Battery Low!” and
further operation will not be possible.
1
Display
Useful information relevant to the procedure at hand is
shown here.
*
The explanations in this manual include illustrations that
depict what should typically be shown by the display.
Note, however, that your unit may incorporate a newer,
enhanced version of the system (e.g., includes newer
sounds), so what you actually see in the display may not
always match what appears in the manual.
3
COMPUTER indicator
This will light when the SD-50 is able to exchange data
with the computer that’s connected to the COMPUTER
connector.
4
5
[MENU] button
This button lets you make system settings (p. 72) or use the
utility functions (p. 74).
2
BATTERY indicator
When running on batteries, this shows the amount of
battery power that remains (p. 21).
Normally, this will be extinguished. It will light when the
batteries run low. If you continue using the unit, the
indicator will eventually start blinking; stop using the unit
and replace the batteries.
[V-LINK] button
This button turns V-LINK on/off (p. 81).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
6
7
8
15
16
17
[TEMPO] button
This button changes the tempo of the song (p. 68).
[
] (STOP) button
This button stops song playback.
[KEY CTRL] button
This button changes the key of the song (p. 68).
[
] (PLAY/PAUSE) button
This button starts or pauses song playback.
[MINUS ONE] (CENTER CANCEL) button
[
] (PREV) button
This button lets you mute a part in a song or reduce the
volume of the melody (e.g., vocal), so that you can play
that part or melody yourself (p. 69).
This button moves to the beginning of the song or selects
the previous song. By holding down this button, you can
rewind the song.
You can perform these operations while the song is
playing or stopped.
9
[
] button
This button lets you repeatedly play a region between two
points (the A-B region) of the song (p. 67).
[
] (NEXT) button
This button selects the next song. By holding down this
button, you can fast-forward the song.
10
11
12
13
14
[VALUE] dial
Use this dial to move the cursor, select parameters, or edit
values.
You can perform these operations while the song is
playing or stopped.
19
20
[EXIT] button
This button cancels the operation, taking you back to the
previous screen.
[FAVORITE] button
You can register a favorite song (p. 70) or studio set (p. 54)
for instant recall.
[ENTER] button
Press this button to confirm a value or execute an
operation.
[PART] button
This button accesses a screen where you can edit the part
settings (p. 49).
[INST] button
This button accesses a screen where you can edit the part’s
sound (p. 46).
[PLAYER] button
This button accesses a screen where you can select songs
(p. 63).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
Rear Panel
ig.XLR_e.eps
1
2
3
4
5
6
7
8
9
10
11
922
1
[POWER] switch
*
This instrument is equipped with balanced (TRS) type
jacks. Wiring diagrams for these jacks are shown below.
Make connections after first checking the wiring diagrams
of other equipment you intend to connect.
This switch turns the power on/off (p. 22).
Setting
BUS
Explanation
When connected to a computer and using bus
power, this setting turns the power on.
fig.TRSJack.eps
TIP:
HOT
OFF
Turns the power off.
RING: COLD
SLEEVE: GND
DC IN/
BATTERY
When using an AC adaptor or batteries (sold
separately), this setting turns the power on.
6
[SETTING] switch
•
•
Set this appropriately for the device connected to the MIC/
GUITAR IN jack.
2
DC IN connector
Connect the AC adaptor here (p. 20).
This switch will turn on the phantom power that is
supplied to the MIC IN jack.
*
You must use the supplied AC adaptor.
3
4
COMPUTER connector
Use a USB cable to connect the SD-50 to your computer
(p. 23).
Nominal
input level
Setting
Explanation
Use the “GUITAR (Hi-Z)” setting
if an electric guitar is
connected to the MIC/GUITAR
IN jack.
GUITAR
(Hi-Z)
-30– -10 dBu
MIDI connectors (OUT, IN)
Use MIDI cables to connect the SD-50 to another MIDI
device (p. 60).
Use the “MIC” setting if a
microphone that does not
require phantom power is
connected to the MIC IN jack,
or if a microphone is
These connectors allow MIDI messages to be transmitted
and received.
MIC
-50 -30 dBu
connected to the MIC/GUITAR
IN jack.
5
MIC/GUITAR IN connector
Connect your guitar or microphone here (p. 55).
Use the “MIC (DC 48V 10mA)”
setting if a phantom-powered
condenser microphone is
MIC
(DC 48V
10mA)
-50– -30 dBu
This is an analog audio input jack with a microphone preamp.
It can accept either balanced or unbalanced connections.
connected to the MIC IN jack.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
9
LINE IN jack
You can connect a portable audio player or similar device
here (p. 58).
Set the [SETTING] switch to “GUITAR” or “MIC” unless
you’ve connected a condenser microphone that
requires phantom power.
Supplying phantom power to a dynamic microphone
will cause malfunction. For details on the specifications
of the microphone you’re using, refer to the owner’s
manual for your microphone.
10
11
LINE OUT jacks
These jacks output the audio signal of the amp and mixer
in stereo (p. 56).
Before you change the position of the [SETTING] switch,
set the volume to “0” using the [VOLUME] dial on the
side panel. If you change the position of the [SETTING]
switch while the volume is raised, loud noise may be
emitted, possibly damaging your amp and speakers.
Ground terminal
If necessary, you can connect this to an external electrical
ground.
927
*
Depending on the circumstances of a particular setup, you
may experience a discomforting sensation, or perceive
that the surface feels gritty to the touch when you touch
this device, microphones connected to it, or the metal
portions of other objects, such as guitars. This is due to an
infinitesimal electrical charge, which is absolutely
7
[SENS] knob
This knob adjusts the input level of the device that’s
connected to the MIC IN jack or MIC/GUITAR IN jack.
When recording, use this knob to adjust the recording
level (p. 56).
harmless. However, if you are concerned about this,
connect the ground terminal with an external ground.
When the unit is grounded, a slight hum may occur,
depending on the particulars of your installation. If you are
unsure of the connection method, contact the nearest
Roland Service Center, or an authorized Roland distributor,
as listed on the separate sheet titled “Information.”
*
Setting [SENS] to the minimum position will not silence the
input completely. If you want to silence the microphone input
completely, set the Mic Input SW to the OFF setting (p. 59).
8
MIC IN jack
You can connect a microphone here (p. 55).
Unsuitable places for connection
This is an analog audio input jack with a microphone preamp.
It can accept either balanced or unbalanced connections.
•
•
•
Water pipes (may result in shock or electrocution)
Gas pipes (may result in fire or explosion)
Telephone-line ground or lightning rod (may be
dangerous in the event of lightning)
*
*
The MIC/GUITAR IN jack and MIC IN jack cannot be used
simultaneously.
The MIC IN jack can provide 48 V phantom power, allowing
a phantom-powered condenser microphone to be
connected.
Set the [SETTING] switch to the “MIC (DC 48 V 10 mA)” if a
phantom-powered condenser microphone is connected to
the MIC IN jack.
922
*
This instrument is equipped with balanced (XLR) type
jacks. Wiring diagrams for these jacks are shown below.
Make connections after first checking the wiring diagrams
of other equipment you intend to connect.
fig.XLRJack.eps
2: HOT
1: GND
3: COLD
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
Side Panel
fig.panel-side_e.eps
1
2
3
4
988
1
2
Security Slot (
http://www.kensington.com/
)
USB MEMORY connector
Connect USB memory (sold separately) here (p. 64).
931
*
Carefully insert the USB memory all the way in—until it is
firmly in place.
3
4
PHONES jack
Connect headphones here.
[VOLUME] dial
This dial adjusts the overall volume of the output from the
rear panel LINE OUTPUT jacks and PHONES jack.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
Bottom Panel
fig.battery-0_e.eps
1
1
Battery compartment
Install six commercially available AA nickel-metal hydride batteries or alkaline batteries in the battery compartment.
This allows the unit to be used even when the AC adaptor is not connected.
Batteries that can be used
Please use nickel-metal hydride batteries or alkaline batteries.
*
Do not use zinc-carbon batteries.
Battery life for continuous operation is as follows.
Type of battery
Continuous use
Nickel-metal hydride
Alkaline batteries
Approximately 4 hours
Approximately 3 hours
*
These times are for operation at room temperature. The length of continuous operation will differ depending on
conditions of use.
Battery handling
•
If batteries are installed, and the power is turned on with the AC adaptor connected, the AC adaptor will be used
preferentially.
•
•
•
If you want to use batteries, disconnect the AC adaptor from the SD-50.
If you want to switch the power from battery or AC adaptor, you must turn off the power first.
If batteries are installed, unplugging the power cord from the AC outlet while the power is turned on will cause the
power to turn off.
•
•
•
The indication shown by the battery indicator is an approximation.
Do not use new batteries together with used batteries, and do not mix batteries of different types.
Improper use of batteries, rechargeable batteries, or chargers may cause electrolyte leakage, overheating, fire, or
explosion.
•
Before use, you must carefully read and observe the cautions and instructions included with your batteries,
rechargeable batteries, and charger.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On/Off
Before You Turn the Power On
Using the AC Adaptor
1. Connect the included AC adaptor and power cord.
2. Connect the AC adaptor to the DC In connector on the rear panel.
fig-connect-AC-Adaptor_e.eps
2
Indicator
AC adaptor
1
To an electrical outlet
Power cord
932
*
*
Place the AC adaptor so the side with the indicator (see illustration) faces upwards and the side with textual
information faces downwards.
The indicator will light when you plug the AC adaptor into an AC outlet.
Using Batteries
1. Press the latches of the bottom panel battery compartment lid, and remove the lid.
fig.Battery-1.eps
•
•
When opening the battery compartment cover, make sure that no foreign objects (flammable items, coins,
pins, etc.) or liquids (water, juice, etc.) enter the compartment.
928
929
When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the
four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient
the unit so no buttons or controls get damaged.
•
When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On/Off
2. Making sure that each battery is oriented in the correct polarity (+/–), insert the batteries into the
battery compartment.
fig.Battery-2.eps
3. Securely close the battery compartment lid.
Battery remaining indication
When the batteries run low, the BATTERY indicator will light.
If you continue use, the BATTERY indicator will blink. Please stop using the unit, and replace the batteries.
fig.battery-3_e.eps
Full
charge
Light
out
Light
replace Blink
*
*
If you continue playing even when the indicator is blinking, the display will indicate “Battery Low!” and further
operation will be impossible.
The indication shown by the battery indicator is an approximation.
Using Bus Power
If the SD-50 is connected to your computer, it can operate using power supplied from your computer via the USB
cable.
You must install the driver if you want to connect the SD-50 to your computer (p. 23).
*
With some computers, the SD-50 might not operate using bus power.
If so, please use the included AC adaptor.
*
When using the SD-50 on bus power, you won’t be able to use phantom power with the MIC IN connector.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning the Power On/Off
Turning the Power On/Off
Turning the Power On
941
Once the connections have been completed (p. 20), turn on power to your various devices in the order
specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers
and other devices.
fig.power_e.eps
[POWER] switch
[VOLUME] dial
1. Verify the following before you turn on the power.
•
•
•
•
The AC adaptor is correctly connected, or batteries are correctly installed.
If using bus power, the SD-50 is correctly connected to the computer and the driver is installed.
The peripheral devices are correctly connected.
The volume of the SD-50 and of the connected equipment is minimized.
2. Set the [POWER] switch to DC IN/BATTERY.
If you’re using bus power, set the [POWER] switch to BUS.
942
*
This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit
will operate normally.
3. Use the [VOLUME] dial to adjust the volume.
4. Adjust the volume of the connected equipment.
Turning the Power Off
1. Minimize the volume of the SD-50 and the connected equipment.
2. Switch off the power on the connected audio equipment.
3. Turn the [POWER] switch OFF.
The display will go dark and the power will turn off.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
A driver is software that transfers data between the SD-50 and the application software on your computer when the
SD-50 is connected to your computer.
The procedure for installation and checking will depend on your system. Perform the following three steps to install
and check the driver.
Windows 7 /
Windows Vista
The procedure for installation and checking
Windows XP
Mac OS X
1. Install the driver
p. 24
p. 28
p. 31
p. 38
p. 33
p. 34
p. 38
2. Input/output device settings
3. Verifying that you hear sound
p. 26
p. 38
*
If you are using the SD-50’s player function (p. 61), the SD-50 cannot be used while connected to a computer.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Windows 7/Windows Vista Users
Steps to be performed on the SD-50 sound module itself are marked by a Operation of the SD-50 symbol. Don’t
connect the SD-50 to your computer until you are told to do so.
*
The example screen shots included here are taken from Windows 7.
1. With the SD-50 disconnected, start up Windows.
Disconnect all USB cables from your computer, with the exception of those for a USB keyboard and USB mouse (if used).
2. Close all currently running software.
3. Insert the included DVD-ROM into your DVD-ROM drive.
When the auto-play dialog box appears, click [Open folder to view files].
4. In the appropriate folder within the included DVD-ROM, double-click the [Setup] icon to start up
the installer.
OS
Folder
Windows 7
Open the folders [Driver] and then [Win7]
Open the folders [Driver] and then [Vista]
Open the folders [x64Driver] and then [Win7]
Open the folders [x64Driver] and then [Vista]
Windows Vista
Windows 7 64-bit edition
Windows Vista 64-bit edition
If you get a message saying “The operating system you are using is not supported” or “The version of this file is not
compatible with the version of Windows you’re running,” or if you don’t know the version of your operating system,
check your operating system as described below.
If “System type” indicates “64-bit Operating System,” you have the 64-bit version.
Windows 7 users
Open “Control Panel,” click “System and Security,” and then click [System].
If the Control Panel shows the icon view, click [System].
Windows Vista users
Open “Control Panel,” click [System and Maintenance], and then click [System].
If the Control Panel shows the classic view, double-click the “System” icon.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
5. A user account control confirmation screen will appear.
Click [Yes] if you’re using Windows 7, or click [Continue] if you’re using Windows Vista.
fig.win7uac_e.eps
6. The screen will indicate “SD-50 Driver will be installed on your computer.” Click [Next].
If any other message appears, proceed as directed by the message.
7. To begin the installation, click [Next] once again.
Installation will begin.
If a Windows security dialog box appears, click [Install].
fig.win7securitya-e.eps_36
8. Operation of the SD-50 Turn the SD-50’s [POWER] switch OFF (p. 22).
9. Operation of the SD-50 When the screen indicates “Ready to install the driver,” use a USB cable to
connect the SD-50 to your computer.
fig.win7drv3-e.eps_36.3
If any other message appears, proceed as directed by the message.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
10. Operation of the SD-50 Switch on the SD-50’s power (p. 20).
The driver will be installed automatically.
*
It can take several minutes for the driver installation to complete.
When the installation is completed, the “SD-50 Driver Setup” dialog box will indicate “Installation has been
completed.”
11. Click [Close] to close the “SD-50 Driver Setup” dialog box.
If the “System Settings Change” dialog box appears, click [Yes]. Windows will automatically restart.
Now let’s check to make sure that installation was successful.
Input/Output Device Settings
In order to use the SD-50 with your software, you’ll need to select the SD-50 as the audio and MIDI input/output
device. For details on how to do this, refer to the documentation for your software.
*
If you’re unable to select the SD-50 as the audio input/output device in your software, it may be that a problem has
occurred. Refer to “Problems with Settings” (p. 94) in the Troubleshooting section.
Audio input/output device
Audio output device
Audio input device
OUT (SD-50)
IN (SD-50)
*
If you’re using ASIO compatible software, select the SD-50 in the ASIO settings of your software.
MIDI input/output device
SD-50
MIDI output device
MIDI input device
SD-50 MIDI
SD-50 CONTROL
SD-50
SD-50 MIDI
SD-50 CONTROL
*
The Windows Media Player included with Windows 7 or Windows Vista cannot use the SD-50’s MIDI input/output
device.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Settings when using the SD-50 in Windows Media Player
Here’s how to specify the SD-50 as the system default playback device so that it can be used with Windows Media
Player.
*
In “Verifying That You Hear Sound” (p. 38), you’ll use Windows Media Player to play back sample data. Be sure to
make the settings described below.
1. Open the “Control Panel,” click the Hardware and [Sound and click Sound].
If you’re using the Icon view or the Classic view, double-click [Sound].
2. Open the [Playback] tab, select the SD-50’s [OUT], and click [Set Default].
3. Click [OK] to complete the setting.
If you select the “SD-50” as the default playback device, audio alerts and other sounds from Windows will also be
output from the SD-50, and therefore will not be heard from your computer’s speakers.
Check the following points before you use the SD-50 to record or play back.
•
•
Connect the SD-50 to your computer before you start up the software you’re using.
Do not disconnect the SD-50’s USB cable from your computer while your software is running. Close the
software you’re using before you disconnect the SD-50’s USB cable from your computer.
This completes driver installation and settings.
Next, verify that you hear sound from the SD-50. ➝ “Verifying That You Hear Sound” (p. 38).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Windows XP Users
Steps to be performed on the SD-50 sound module itself are marked by a Operation of the SD-50 symbol. Don’t
connect the SD-50 to your computer until you are told to do so.
1. With the SD-50 disconnected, start up Windows.
Disconnect all USB cables from your computer, with the exception of those for a USB keyboard and USB mouse (if used).
2. Close all currently running software.
3. Insert the included DVD-ROM into your DVD-ROM drive.
4. On the included DVD-ROM, open the [Driver] folder and then the [XP] folder, and double-click the
[Setup] icon.
If you get a message saying “The operating system you are using is not supported” or saying that the application is
invalid, check the version of your operating system.
If the “Install Program As Other User” dialog box appears, click [Cancel] to terminate the installation, log on to
Windows using an administrator account, and perform the installation once again.
5. The screen will indicate “SD-50 Driver will be installed on your computer.” Click [Next].
If any other message appears, proceed as directed by the message.
6. To begin the installation, click [Next].
If the “Software Installation” dialog box appears, click [Continue Anyway] to continue the installation.
fig.xpdrv2-e.eps_2
If you are unable to proceed, click [OK] in the dialog box to terminate the installation. Then change the setting as
described in “Driver Signing Option Settings (Windows XP)” (p. 99), and perform the installation once again.
7. Operation of the SD-50 Switch off the SD-50’s power (p. 22).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
8. Operation of the SD-50 When the “Ready to install the driver” message appears, use a USB cable to
connect the SD-50 to your computer.
fig.xpdrv4-e.eps_27
If any other message appears, proceed as directed by the message.
9. Operation of the SD-50 Switch on the SD-50’s power (p. 20).
The indication “Found New Hardware” will appear in the lower right corner of your screen.
*
It may take several minutes for the “Found New Hardware Wizard” to appear.
10. If you are asked whether you want to connect to Windows Update, choose [No, not this time] and
click [Next].
fig.xpwupd-e.eps
11. Choose [Install the software automatically (Recommended)], and click [Next].
fig.xpdrv6-e.eps
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
12. If the “Hardware Installation” dialog box appears, click [Continue Anyway] to continue the
installation.
fig.xpdrv7-e.eps
If you are unable to proceed, click [OK] in the dialog box to terminate the installation. Then change the setting as
described in “Driver Signing Option Settings (Windows XP)” (p. 99), and perform the installation once again.
13. The screen will indicate “Completing the Found New Hardware Wizard.” Click [Finish].
When installation is complete, the “SD-50 Driver Setup” dialog box will indicate “Installation has been completed.”
14. Click [Close] to close the “SD-50 Driver Setup” dialog box.
If the “System Settings Change” dialog box appears, click [Yes] to restart Windows.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Input/Output Device Settings
In order to use the SD-50 with your software, you must select the SD-50 as the audio input/output device. For details
on how to make this setting, refer to the documentation for the software you’re using.
*
If you’re unable to select the SD-50 as the audio input/output device in your software, it may be that a problem has
occurred. Refer to “Problems with Settings” (p. 94) in the Troubleshooting section.
Audio input/output device
Audio output device
Audio input device
OUT (SD-50)
IN (SD-50)
*
If you’re using ASIO compatible software, select the SD-50 in the ASIO settings of your software.
MIDI input/output device
SD-50
MIDI output device
MIDI input device
SD-50 MIDI
SD-50 CONTROL
SD-50
SD-50 MIDI
SD-50 CONTROL
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Settings when using the SD-50 in Windows Media Player
Here’s how to specify the SD-50 as the system default playback device so that it can be used with Windows Media
Player.
*
In “Verifying That You Hear Sound” (p. 38), you’ll use Windows Media Player to play back sample data. Be sure to
make the settings described below.
1. Open the “Control Panel,” click [Sounds, Speech, and Audio Devices], and then double-click the
[Sounds and Audio Devices].
*
If you’re using the Classic view, double-click the [Sounds and Audio Devices icon].
2. Click the Audio tab to open it, and in the Sound playback area, select OUT (SD-50). In the MIDI
Music Playback area, select SD-50.
3. Click [OK] to complete the setting.
*
If you select the SD-50 as the default playback device, audio alerts and other sounds from Windows will also be
output from the SD-50, and therefore will not be heard from your computer’s speakers.
Caution when recording or playing back with your software
Check the following points before you use the SD-50 to record or play back.
•
•
Connect the SD-50 to your computer before you start up the software you’re using.
Do not disconnect the SD-50’s USB cable from your computer while your software is running. Close the
software you’re using before you disconnect the SD-50’s USB cable from your computer.
This completes driver installation and settings.
Next, verify that you hear sound from the SD-50. ➝ “Verifying That You Hear Sound” (p. 38)
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Mac OS X Users
Steps to be performed on the SD-50 sound module itself are marked by a Operation of the SD-50 symbol. Don’t
connect the SD-50 to your computer until you are told to do so.
*
If the “Authenticate” or “Installer requires that you type your password” dialog box appears during the installation,
enter an administrator password and click [OK].
*
What you actually see on the screen may differ depending on your system.
1. With the SD-50 disconnected, start up your computer.
Disconnect all USB cables from your computer, with the exception of those for a USB keyboard and USB mouse (if used).
2. Close all currently running software.
3. Insert the included Mobile Studio Canvas DVD-ROM into your DVD-ROM drive.
4. Double-click one of the following icons on the DVD-ROM to start up the installer.
OS
Installer
Mac OS X 10.6 or later
Mac OS X 10.5 or earlier
[SD-50_USBDriver.pkg] (/Driver/10.6)
[SD50USBDriver.pkg] (/Driver/10.4_10.5)
A message concerned with checking whether installation is possible may appear.
If so, click [Continue].
If a message indicating that installation is not possible appears, check the operating system you’re using, and
perform step 4.
5. The screen will indicate “Welcome to the SD-50 Driver Installer.” Click [Continue].
fig.osx-install-e.eps
6. If the screen asks you to select a destination, click your start-up disk to select it, and then click
[Continue].
7. When the display asks you to select the type of installation, click [Install] or [Upgrade].
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
8. In the next screen, click [Continue Installation].
9. When installation is completed, click [Restart] to restart your computer.
*
It may take some time for your computer to restart.
10. Operation of the SD-50 Switch off the SD-50’s power (p. 22).
11. Operation of the SD-50 When your computer has restarted, use a USB cable to connect the SD-50 to
your computer.
12. Operation of the SD-50 Switch on the SD-50’s power (p. 22).
Input/Output Device Settings
In order to use the SD-50 with your software, you’ll need to select the SD-50 as the audio input/output device (p. 35)
and MIDI input/output device. For details on how to do this, refer to the documentation for your software.
Audio input/output device settings
Audio output device
Audio input device
SD-50 44.1kHz
SD-50 44.1kHz
*
If you’re unable to select the SD-50 as the audio input/output device in your software, it may be that a problem has
occurred. Refer to “Problems with Settings” (p. 94) in the Troubleshooting section.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Using the SD-50 with iTunes
Here’s how to specify the SD-50 as the sound output device so that it can be used with iTunes.
In “Verifying That You Hear Sound” (p. 38), you’ll use iTunes to play back sample data. Be sure to make the settings
described below.
*
The content displayed may differ depending on your system.
1. In [System Preferences], click [Sound].
2. Click the [Output] tab.
Select [SD-50 44.1kHz].
3. When you’ve finished making the setting, close [System Preferences].
MIDI input/output device settings
1. Double-click [Audio MIDI Settings] (/Applications/Utility) to start it up.
2. Access the dialog box.
Mac OS X 10.6 or later
From the [Window] menu, choose [Show MIDI Window] to open “MIDI Studio”
Mac OS X 10.5 or earlier
Click the [MIDI Devices] tab.
3. Verify that [SD-50] is shown in the “MIDI Studio” or “Audio MIDI Settings” dialog box.
fig.osxaudiomidi1-e.eps
If the SD-50 is not shown or is grayed-out, the SD-50 has not been recognized correctly. Try clicking [Rescan MIDI].
You can also try disconnecting the USB cable connected to the SD-50, then re-connecting it.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
4. Click [Add Device] three times.
fig.osxadddevice-e.eps
Three [New Device] items will appear.
5. Specify the device name for each [New Device].
1. Select the [New Device] you added, and click [Show Info].
2. Enter the name in the [Device Name] field. For each [New Device], enter the following names.
fig.osxnewdevice-e.eps
New Device
Device Name
SD-50
First [New Device]
Second [New Device]
Third [New Device]
SD-50 MIDI
SD-50 CONTROL
6. Use the mouse to drag between the ▲ and ▼ symbols (representing input and output,
respectively) of [SD-50] and each [New Device] so that they are connected as shown in the
illustration below.
fig.osxmidiset-e.eps_32
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
7. Check to make sure that MIDI transmission and reception takes place normally.
1. Click “Test Setup.”
2. Turn down the SD-50’s volume.
The following step will cause a fairly loud sound to be produced from the SD-50.
3. Click the SD-50’s downward arrow.
If the SD-50 produces sound, the settings are correct.
fig.XXXXXXXXXXXXX
Click
Click
4. Click “Test Setup” once again to end the test.
8. From the [Audio MIDI Setup] menu, select [Quit Audio MIDI Setup] to finish making settings.
Caution when recording or playing back with your software
Check the following points before you use the SD-50 to record or play back.
•
•
Connect the SD-50 to your Macintosh before you start up the software you’re using.
Do not disconnect the SD-50’s USB cable from your Macintosh while your software is running. Close
the software you’re using before you disconnect the SD-50’s USB cable from your Macintosh.
The SD-50 will not work with the Mac OS X Classic environment. Use the SD-50 when the classic
environment is not running.
•
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
Playing Back the Sample Data
Here we will play back sample data using the standard functionality provided by your operating system. The sample
data “TTears(.mp3)” is in the included DVD-ROM.
*
Copyright law prohibits you from using the song data included with this product for any purpose other than
personal enjoyment unless you have obtained permission from the copyright holder. You may not copy this data
or use it in a derivative work without permission from the copyright holder.
1. Insert the included DVD-ROM into the DVD-ROM drive of your computer.
2. From the Sample folder of the DVD-ROM, copy the file TTears(.mp3) to your desktop.
3. Play back the sample data “TTears”(.mp3).
Double-click the TTears(.mp3) file you copied to your desktop.
If you’re using Windows, Windows Media Player will start. If you’re using Macintosh, iTunes will start. Click the play
button, and the sample data will start playing.
*
Depending on your system, other playback software may start up. If so, play the sample data as described in the
documentation for the software you’re using.
4. Adjust the volume.
Use the SD-50’s [VOLUME] dial to adjust the volume.
You should hear the sample data played from the headphones or speakers connected to the SD-50.
Did you hear the sample data?
If you could hear the sample data, the SD-50 is correctly connected to your computer and the driver has
been installed correctly.
If you could not hear the sample data, refer to “Troubleshooting” (p. 88). If there’s no sound, or if there’s
something wrong with the playback, information provided in that section will help you solve the
problem.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Playlist Editor
You can create playlists for playing SMFs or audio files on the SD-50 using the Playlist Editor.
When using the SD-50 to play backing tracks (accompaniment), it’s convenient to create a playlist that specifies the
desired order for the songs.
For details on using this, refer to the PDF manual that is installed together with Playlist Editor.
Installing Playlist Editor
The procedure for installing Playlist Editor will depend on your system.
Windows 7 / Windows Vista users
1. Insert the included DVD-ROM into your DVD-ROM drive, and double-click the [Setup.exe] file
located in the Editor folder.
2. A user account control dialog box will appear; click [Continue].
3. The installer will start up. Follow the instructions that appear on the screen to install Playlist
Editor.
Windows XP Users
1. Insert the included DVD-ROM into your DVD-ROM drive, and double-click the [Setup.exe] file
located in the Editor folder.
2. The “Welcome” screen will appear. Click [Next].
3. Follow the instructions that appear on the screen to install Playlist Editor.
Mac OS X Users
1. On the included DVD-ROM, open the Editor folder and double-click [Playlist Editor Installer.pkg].
2. The installer will start up. Follow the instructions that appear on the screen to install Playlist
Editor.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Playlist Editor
Creating a Playlist
Start up Playlist Editor and create a playlist.
PlaylistEditor.eps_35
*
*
*
For details on how to create a playlist, refer to “PlaylistEditorManual.E.pdf” from the “Playlist Editor” help.
You’ll need to use the included “Playlist Editor” to create playlists. They cannot be created on the SD-50 itself.
You can play songs individually without creating a playlist. To do so, place the SMF or audio files in the root directory of
your USB memory.
Viewing the online manual
Playlist Editor’s online manual is located in the Manual folder within the folder in which Playlist Editor
was installed. The online manual is provided as a PDF file. You’ll need Adobe Reader (available free of
charge) in order to view PDF files.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
42
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Sound Generator
The SD-50’s sound generator has the following two modes. In Normal mode, you can select sounds from the SD-50
itself. For more about selecting sounds, refer to “Selecting a Tone For Each Part” (p. 46).
Normal mode
This is the normal state of the SD-50. You’ll be able to select and play sounds from three groups: PRESET, GM2, and
Solo.
Group
Number of sounds
Explanation
PRESET
640 sounds+14 drum sets
This is the SD-50’s original set of sounds.
These are sounds that comply with GM2, which standardizes MIDI sound
modules across manufacturers and models.
*
You can choose the following two types of GM sounds. Specify the
desired GM type as described in “System Settings” (p. 72).
•
Classical
GM2
256 sounds +9 drum sets
You should also use this sound set if GM2 data compatibility is an
important consideration.
•
Contemporary
This is a set of sounds that emphasizes the realism of each individual
instrument. This set is selected when the SD-50 is powered up.
These sounds realistically simulate the tonal characteristics of acoustic
instruments and the unique performance techniques used with a variety of
instruments.
Solo
3 sounds
For more about settings for Solo sounds and how to play them, refer to
“The Solo sounds and how to play them” (p. 106).
GS mode
Use this mode when you play back GS performance data. GS mode is activated when the SD-50 receives a GS Reset
MIDI message (system exclusive message).
Group
Number of sounds
Explanation
This sound set complies with the “GS” sound generator format promoted by
Roland Corporation.
*
If GS mode is selected, the following settings will be unavailable.
GS
226 sounds +9 drum sets
•
•
•
•
“Selecting a Tone For Each Part” (p. 46)
“Adjusting the Pan and Effect Depth” (p. 51)
“Adjusting the Effect Settings” (p. 52)
“Saving a Studio Set” (p. 54)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Explanation of Terms
Tone
On the SD-50, a “tone” is the unit of sound (e.g., piano, organ, guitar) that you can select. For the available tones, refer
to PDF “Tone List.”
Drum set
A “drum set” is a group of percussion instrument sounds. Since percussion instruments are not usually used to play a
melody, it’s not necessary that you be able to play different pitches of the instrument from the keyboard. Rather, it’s
important that you be able to use a large number of percussion instrument sounds simultaneously.
For this reason, a drum set produces the sound of a different percussion instrument for each key (note number).
For the available drum sets, refer to PDF “Tone List.”
Part
On the SD-50, a “part” is a unit to which a tone or drum set is assigned.
The SD-50 provides sixteen parts, and you can assign a different tone or drum set to each part.
Effect
An “effect” refers to processing that can be applied to modify the sound. By switching effects, you can significantly
alter the character of the sound.
The SD-50 contains the following effects; you can modify the depth and type of each effect (p. 52).
Type
Explanation
Chorus
Reverb
Mastering
Adds depth and spaciousness to the sound.
Adds the reverberation that is characteristic of a performance in a hall.
Makes the overall sound more consistent and powerful.
Studio set
A “studio set” is a collection of settings for the sixteen parts and the effects.
fig.studio-set_e.eps
Studio set
Effect
Part 16
Part 1
Tone/
Drum set
Polyphony
The number of notes (polyphony) that the SD-50 can produce simultaneously will depend on the tones that are
selected. The SD-50’s maximum polyphony is 128 notes, but the actual polyphony will be less depending on the
tones you use.
If your performance exceeds the maximum polyphony, newly played notes will be given priority, while notes that
were sounded previously will be turned off one by one.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Selecting a Tone For Each Part
Selecting From the Tone List
Here’s how to select a tone from a list. Refer to PDF “Tone List” for information on the available tones.
1. Press the [PART] button a number of times to access the MIDI part screen.
page_part_meter.eps
2. Turn the [VALUE] dial to select the part whose tone you want to change.
page_part_meter.eps
3. Press the [INST] button to access the tone list screen.
page_patch_list-1.eps
4. Turn the [VALUE] dial to select a tone.
page_patch_list-2.eps
Press the [
] button and Sample notes will be played so you can audition the tone.
5. Press the [ENTER] button.
The tone has now been selected.
page_part_meter-5h.eps
If you save the studio set, your selections will be saved to internal memory (p. 54).
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Selecting by Category or Group
Here’s how to select a tone by category such as piano or organ, or from a group such as PRESET, GM2, or Solo.
1. Press the [PART] button a number of times to access the MIDI part screen.
page_part_meter.eps
2. Turn the [VALUE] dial to select the part whose tone you want to change.
page_part_meter.eps
3. Press the [INST] button a number of times to access the category group screen.
page_patch_grp.eps
4. Turn the [VALUE] dial to select either “CATEGORY” or “GROUP,” and then press the [ENTER]
button.
The category list or group list will appear.
page_patch_grp_list.eps
5. Turn the [VALUE] dial to select the desired category or group, and then press the [ENTER] button.
The first tone in the selected category or group will be selected.
For information on the tones in each category or group, refer to PDF “Tone List.”
page_patch_list.eps
Press the [
] button and Sample notes will be played so you can audition the tone.
Your selection will be saved to internal memory if you save the studio set (p. 54).
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Viewing a Tone’s Program Change and Bank Select Numbers
Here’s how to check the program change and bank select numbers of the currently selected tone.
1. Press the [INST] button a number of times to access the tone information screen.
page_tone_info.eps
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Adjusting the Settings of Each Part
For each part, you can adjust its volume and other settings, and apply effects to the sound.
Muting/Soloing a Part
You can “mute” a specific part so that it will not produce sound.
Conversely, you can “solo” a specific part so that it will play while all of the other parts are muted.
1. Press the [PART] button a number of times to access the MIDI part screen.
page_part_meter.eps
2. Turn the [VALUE] dial to select the part that you want to mute or solo, and then press the [ENTER]
button.
page_part_meter-1.eps
3. Turn the [VALUE] dial to change the setting.
page_part_meter-s.eps
Setting
Explanation
Muted
M
S
Soloed
The mute and solo settings will be saved in internal memory if you save the studio set (p. 54).
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Adjusting Each Part’s Volume
Here’s how to adjust the volume of a specific part.
1. Press the [PART] button a number of times to access the MIDI part screen.
page_part_meter.eps
2. Turn the [VALUE] dial to select the part whose volume you want to adjust, and then press the
[ENTER] button twice.
page_part_meter-100.eps
3. Turn the [VALUE] dial to adjust the setting.
Value
0–127
The adjusted volume of each part will be saved in internal memory if you save the studio set (p. 54).
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Adjusting the Pan and Effect Depth
You can specify the pan (stereo position) of each part, and adjust the depth of the reverb and chorus effects for each
part.
1. Press the [PART] button a number of times to access the Part Edit screen.
page_part_edit-1.eps
2. Turn the [VALUE] dial to select the effect whose settings you want to adjust, and then press the
[ENTER] button.
page_part_edit-3.eps
Setting
Value
0–127
0–127
0–127
Explanation
Pan
Left/right balance of the sound.
Reverb Send
Chorus Send
Depth of reverb. Choose “0” if you don’t want to apply reverb.
Depth of chorus. Choose “0” if you don’t want to apply chorus.
3. Turn the [VALUE] dial to adjust the setting.
The pan and effect settings you specify will be saved in internal memory if you save the studio set (p. 54).
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
Adjusting the Effect Settings
Here’s how to adjust the effect settings and other settings of the studio set.
1. Press the [PART] button a number of times to access the Studio Set Edit screen.
page_studio_edit.eps
2. Turn the [VALUE] dial to select the item you want to edit, and then press the [ENTER] button.
page_studio_edit-2.eps
Setting
Value
Explanation
SMALL ROOM, MEDIUM ROOM, LARGE ROOM:
Reverb simulating the acoustics of a room, producing a crisp and spacious
reverberation.
SMALL ROOM,
MEDIUM ROOM,
LARGE ROOM,
MEDIUM HALL,
LARGE HALL,
PLATE
Rev Type
MEDIUM HALL, LARGE HALL:
Reverb simulating the acoustics of a hall, producing reverberation with more space
than Room.
PLATE: Simulation of a plate reverb unit (a device using the vibration of a metal plate).
Adjusts the duration of the reverb. Higher settings produce longer reverb.
Selects either Chorus or Reverb.
Rev Time
0–127
Cho mode
CHORUS, DELAY
When “CHORUS” has been selected for “Cho mode.”
CHORUS1, CHORUS2, CHORUS3, CHORUS4:
Typical chorus effect, adding depth and spaciousness to the sound.
FB CHORUS: Chorus effect that produces a soft, flanger-like sound.
FLANGER: Produces a sound that’s reminiscent of a jet airplane taking off and landing.
Chorus with feedback applied to it.
CHORUS1, CHORUS2,
CHORUS3, CHORUS4,
FB CHORUS, FLANGER
Cho Type
Cho Rate
Cho Depth
Feedback
Rev Send
0–127
0–127
0–127
0–127
Adjusts the rate of modulation.
Adjusts the depth of modulation.
Adjusts the amount of chorus sound to be fed back into the input.
When “DELAY” has been selected for “Cho mode.”
Adjusts the amount of time it is to take for the delay sound to be heard after the
original sound has sounded.
Dly Time
Dly FB
0–1000 ms, note
-98– +98 %
Adjusts the proportion of the delay sound to be fed back to the input. (Minus:
reversed phase)
Adjusts the frequency at which the high-frequency components of the delay sound
fed back to the input will be cut. (BYPASS: no cut)
Dly HF DMP
200– 8000 Hz, BYPASS
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
3. Turn the [VALUE] dial to adjust the setting.
The effect settings you adjust will be saved in internal memory if you save the studio set (p. 52).
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Sound Module
You can save the studio set you’ve edited. This means that the sounds you’ve selected for the SD-50’s parts, as well as
other settings, will be saved in internal memory. You can save three different studio sets in internal memory.
1. Edit the studio set as desired.
Make settings as described in “Selecting a Tone For Each Part” (p. 46), “Adjusting the Settings of Each Part” (p. 49),
and “Adjusting the Effect Settings” (p. 52)
2. Press the [FAVORITE] button for a number of seconds until the REGIST SONG screen appears.
page_regist_favorite.eps
3. Press the [FAVORITE] button a number of times to access the REGIST STUDIO SET screen.
page_studio_write.eps
4. Press one of the [PART](1) – [PLAYER](3) buttons.
Once the following screen appears, the studio set has been saved.
page_studioset_write.eps
Recalling a Studio Set
1. Press the [FAVORITE] button a number of times to access the screen shown below.
The saved studio sets will be displayed, and the LEDs for the [PART](1) – [PLAYER](3) buttons will blink.
page_patch_grp_select.eps
2. Press one of the [PART](1) – [PLAYER](3) buttons.
The studio set will be recalled.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an Audio Interface
By connecting the SD-50 to your computer, you can use it as an audio interface.
This also allows you to connect a microphone or guitar, and record your vocal or instrumental performance into the
computer.
983
*
Howling could be produced depending on the location of microphones relative to speakers. This can be remedied by:
1. Changing the orientation of the microphone(s).
2. Relocating microphone(s) at a greater distance from speakers.
3. Lowering volume levels.
fig.connect-3_e.eps
Electric Guitar
Portable
Audio Device
Microphone
Computer
USB connector
[SETTING] switch
[SENS] knob
SD-50
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an Audio Interface
Listening to Playback from Your Computer
1. Use a USB cable to connect the SD-50 to your computer.
2. Play back an audio file (e.g., WAV or MP3) on your computer.
The playback of your computer will be heard from the SD-50.
Recording Your Microphone or Guitar
If you connect a microphone or guitar to the SD-50, you’ll be able to record a vocal or guitar performance into the
computer.
Getting Ready to Record
Connect your microphone or guitar
1. Use a USB cable to connect the SD-50 to your computer.
2. Set the [SETTING] switch to the appropriate position.
Set the [SETTING] switch as appropriate for the jack or device you’re connecting.
Connected device
Connected jack
MIC/GUITAR IN jack
MIC/GUITAR IN jack
MIC IN jack
Setting
GUITAR (Hi-Z)
MIC
Nominal input level
-30– -10 dBu
Guitar
-50– -30 dBu
Dynamic microphone
(phantom power not required)
MIC
-50– -30 dBu
Condenser microphone
(phantom power required)
MIC IN jack
MIC (DC 48 V 10 mA)
-50– -30 dBu
3. Connect your microphone or guitar to the MIC IN jack or the MIC/GUITAR IN jack.
Connect a microphone to the MIC IN jack or MIC/GUITAR IN jack. Connect a guitar to the MIC/GUITAR IN jack.
*
You can’t use both the MIC/GUITAR IN and MIC IN jacks simultaneously.
You can apply echo to the microphone (p. 59).
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an Audio Interface
Adjust the input level
1. Press the [PART] button a number of times to access the audio part screen.
The level meters will appear.
page_audio_meter-mic.eps
2. Turn the [SENS] knob to adjust the input volume.
In order to record with the best audio quality, use the [SENS] knob to increase the level as far as possible without
allowing an overload to occur; i.e., don’t let the level meter reach the maximum point.
You can apply echo to the sound of the connected microphone or guitar (p. 59).
*
If the indication below appears, the input level has overloaded even though the level meter did not reach the
maximum point.
fig.input-level-over.eps
Recording
1. Operate your computer to start recording.
For details on how to start recording, refer to the user’s guide for the software you’re using.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an Audio Interface
Recording Sound From the Line Input
You can connect your portable audio player or other audio device to the SD-50’s line input, and record the sound into
the computer from that device.
Getting Ready to Record
Connect your audio device
1. Use a USB cable to connect the SD-50 to your computer.
2. Connect your portable audio player or other audio device to the LINE IN jack.
Adjust the input level
1. Press the [PART] button a number of times to access the audio part screen.
The level meters will appear.
page_audio_meter-mic.eps
2. Adjust the output level of the connected audio device.
You can apply echo (p. 59) or center cancel (p. 69) to the sound of the audio device connected to LINE IN, or
modify its pitch (p. 68).
*
If the indication below appears, the input level has overloaded even though the level meter did not reach the
maximum point.
In this case, you should keep the input at a low level by turning ON the “Audio Input Att” in the Audio Settings screen
(p. 59).
page_audio_meter-clip.eps
Recording
1. Operate your computer to start recording.
For details on how to start recording, refer to the user’s guide for the software you’re using.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an Audio Interface
Input/Output and Effect Settings
Here you can apply an effect to the external audio input via a microphone or guitar, and specify how the audio is to
be output.
1. Press the [PART] button a number of times to access the Audio Setting screen.
page_audio_setting-1.eps
2. Turn the [VALUE] dial to select the item you want to edit, and then press the [ENTER] button.
page_audio_setting-3.eps
Indication
Values
Explanation
Switches on/off the audio input via the MIC IN jack. If this is “OFF,” no audio will
be input via the MIC IN jack. This allows you to reduce the input noise when
you’re recording the audio from the MIDI sound generator on an external device.
Mic Input Sw
(Mic input switch)
ON, OFF
Adjusts the amount of echo applied to the microphone connected to the MIC IN
jack or MIC/GUITAR IN jack. Higher values produce a deeper echo effect.
Mic Echo Level
0 –10
Audio Input Att
(Audio input attenuator)
Reduces the input level from the MIC IN jack, MIC/GUITAR IN jack, and LINE IN
jack. This will reduce input noise.
ON, OFF
Specifies whether the audio signal being input via the MIC IN jack, MIC/GUITAR
IN jack, or LINE IN jack will be output from the PHONES jack and LINE OUT jacks.
ON: The audio input signal will be output.
Direct Mon Sw
(Direct Monitor Switch)
ON, OFF
0–127
OFF: The audio input signal will not be output.
Direct Mon Level
(Direct Monitor Level)
Adjusts the output volume for direct monitors.
Specifies whether the audio signal of the SD-50’s MIDI sound generator will be
output to the computer.
ON: The audio signal of the SD-50’s sound generator will be output.
OFF: The audio signal of the SD-50’s sound generator will not be output.
TG to COMPUTER
ON, OFF
The settings “Direct Mon Sw,” “Direct Mon Level” and “TG to COMPUTER” are displayed only when the unit
has been connected to a computer.
3. Turn the [VALUE] dial to edit the setting.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as a MIDI Interface
You can connect a MIDI keyboard to the SD-50 and use it as a MIDI interface for your computer.
This lets you create song data by playing your MIDI keyboard. For details on how to make the necessary settings, refer
to the user’s guide for the software you’re using.
If the SD-50 is not connected to a computer, you can use your MIDI keyboard to play the SD-50’s sound generator.
When connected to a computer
fig.connect-MIDI-Inter-pc_e.eps
MIDI signal flow
MIDI keyboard
Sound
Generator
Computer
SD-50
When not connected to a computer
fig.connect-MIDI-Inter-npc_e.eps
MIDI signal flow
MIDI keyboard
Sound
Generator
SD-50
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
The SD-50 can function as a music player that can play SMF or audio files.
You can use your computer to create a “playlist” that specifies a playback order for “songs” (SMF/audio files), and
then transfer this via USB memory and use it on the SD-50.
In addition to playing songs in the order specified by a playlist, you can also select and play individual songs from the
playlist.
Getting ready to use the SD-50 as a player
1. Copy the data to USB memory
fig.Player-howto-1_e.eps
SMF, WAV,
AIFF, MP3 files
USB memory
2. Connect the USB memory to the SD-50
fig.Player-howto-2_e.eps
USB memory
931
*
*
*
*
Carefully insert the USB Memory all the way in—until it is firmly in place.
Please use USB memory sold by Roland. Operation cannot be guaranteed if you use other products.
If you’re using new USB memory, you must first format it using the SD-50 (p. 74).
The SD-50 cannot be used as a music player while it’s connected to your computer via USB.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
What is SMF?
SMF (Standard MIDI File) is a data format that was created in order to standardize music data across
manufacturers. Many collections of SMF music data are available in a wide range of musical styles for listening
enjoyment, instrument practice, or karaoke.
SMF/audio files that can be played
SMF
0 or 1
*
Format
SMF format 1 limits the tracks that can be played back.
MID
Maximum of approximately 240 KB
(differs slightly depending on the content of the SMF)
File size
System exclusive
Packet size of 512 bytes or less
Audio files
Sampling frequency
Bit depth
44.1 kHz
WAV/AIFF
MPEG-1 audio layer 3
44.1 kHz
Format
Sampling frequency
MP3
32/40/48/56/64/80/96/112/128/160/192/224/256/320 kbps,
VBR (Variable Bit Rate)
Bit rate
*
*
You can’t use SMF/audio file playback employing USB memory while the SD-50 is connected to a computer.
Some utility functions (p. 74) cannot be executed while the player is playing back a song.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
Listening to the Demo Songs
Here’s how to listen to the demo songs that are built into the SD-50.
1. Switch on the SD-50’s power (p. 22).
2. Press the [PLAYER] button twice; the playlist screen will appear.
The button’s indicator will light.
fig.screen_play_list.eps
3. Turn the [VALUE] dial to move the cursor to “Demo Songs.”
page_play_list-demo1.eps
4. Press the [
].
Playback will start from the first demo song.
page_play_Demo-play.eps
5. To stop song playback, press the [
].
*
If you’ve connected USB memory in which you’ve saved song files, choose “Demo Songs” in the playlist screen. For
more about playing from a playlist, refer to page 64.
982
*
*
No data for the music that is played will be output from MIDI OUT.
981b
Use of the demo song supplied with this product for any purpose other than private, personal enjoyment without the
permission of the copyright holder is prohibited by law. Additionally, this data must not be copied, nor used in a
secondary copyrighted work without the permission of the copyright holder.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
Playing Back
Selecting a Song
1. Connect USB memory containing playlists and songs to the SD-50.
2. Press the [PLAYER] button a number of times to access the playlist screen.
The button’s indicator will light.
fig.screen_play_list.eps
*
If a
is shown at the left of the playlist name, you cannot edit that playlist’s settings or change the settings of the
songs within that playlist.
3. Turn the [VALUE] dial to move the cursor to the playlist that you want to play.
page_play_list-11.eps
When you press the [
To stop playback, press the [
The next time you press the [
] button, playback will start from the first song in the playlist.
] button.
] button, playback will resume from where you stopped it.
4. Press the [ENTER] button.
The playlist will be selected, and the song list will appear.
page_song_list-1.eps
*
If the song is not of a file type that can played by the SD-50, a “?” symbol will appear. This song will not be played.
5. Turn the [VALUE] dial to move the cursor to the song that you want to play.
page_patch_list-2.eps
When you press the [
To stop playback, press the [
The next time you press the [
] button, the song will start playing.
] button.
] button, playback will resume from where you stopped it.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
6. Press the [ENTER] button.
The play screen will appear.
page_song_player-opening.eps
Playing a Song
1. From the play screen, press the [
Playback operation buttons
] button to start playing the song.
Operation
Press the [
Press the [
Press the [
Press the [
Press the [
Explanation
] button
] button
Play
Pause
] button
Stop
] button
] button
Next song
Previous song
*
If A-B Repeat is on, pressing [
] moves you to marker B, and pressing [
] moves you to marker A (p. 67).
Playing back from the middle of a song
1. In the play screen, press the [ENTER] button.
The play screen cursor will be shown as follows.
page_song_way.eps
Cursor
2. Turn the [VALUE] dial to specify the desired point within the song that you want to play.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
Adjusting the volume of the song
1. In the play screen, turn the [VALUE] dial.
The screen will appear as follows, you can change the volume.
You can also adjust the song volume from the audio part screen (p. 59).
page_song_playe-volumer.eps
Chain Play / Repeat All settings
You can use Chain Play for the songs in the playlist, or play all songs repeatedly.
This screen will not appear if is shown at the left of the playlist name.
*
1. Press the [PLAYER] button a number of times to access the play mode screen.
page_song_mode-1.eps
2. Turn the [VALUE] dial to specify how the song is to play, and then press the [ENTER] button.
page_song_level_edit.eps
Play mode
Values
Explanation
The songs in the playlist will play consecutively. When the last song finishes playing, playback
will stop.
Chain Play
ON, OFF
The songs in the playlist will play consecutively, and when the last song finishes playing,
playback will return to the first song and continue playing consecutively.
Repeat All
ON, OFF
3. Turn the [VALUE] dial to turn the play mode setting on or off.
If you decide to cancel, press the [EXIT] button.
4. Press the [ENTER] button.
The play mode setting will be stored.
If the following screen appears
If you attempt to exit play mode without saving the play mode
settings, the screen shown at right will appear.
If you want to execute the changes you made in play mode, press the
[ENTER] button. If you want to cancel them, press the [EXIT] button.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
A-B Repeat
This lets you repeatedly play back a specific region within a song.
This is a convenient way to listen repeatedly to a passage of interest.
1. Play back the song.
2. During playback, press the [
] button.
Start point (A) has now been specified.
The [
] button’s indicator will blink.
3. Press the [
] button once again.
End point (B) has now been specified.
The [
] button’s indicator will light.
The region (A-B) you specified in steps 2 and 3 will play repeatedly.
To cancel repeat playback, press the [ ] button once again.
If you set point A and then allow the song to play to its end without specifying point B, playback will repeat
between point A and the end of the song.
Playback operation buttons when using A-B Repeat
Button operation
Explanation
Press the [
] button
] button
] button several seconds
] button several seconds.
] button
Stop playback and move to point A.
Stop playback and move to point B.
Fast-forward. Playback will stop at point B.
Rewind. Playback will stop at point A.
Playback will stop, with point A and B settings remembered.
Press the [
Hold down the [
Hold down the [
Press the [
Cancelling the A-B Repeat settings
•
With point A and point B specified, press [
]; the point A and point B settings will be cleared.
•
The point settings will also be cleared if you select a different song.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
Changing the Tempo
1. Play back a song.
*
If you change the tempo while the song is stopped, the song’s playback tempo will not be changed.
2. Press the [TEMPO] button.
The tempo screen will appear.
page_tempo.eps
Audio
MIDI
3. Turn the [VALUE] dial.
The song’s tempo will change.
When you play back a MIDI file, the [TEMPO] button’s indicator will blink in time with the tempo. It will blink red at the
beginning of the measure, and green on other beats.
Data type
Audio file
MIDI file
Tempo range
50%–125%
5–300 (BPM)
*
You can’t change the tempo of audio that’s being input via the MIC IN jack or LINE IN jack.
4. Press the [TEMPO] button to exit the Tempo screen.
Changing the Key
1. Play back a song.
2. Press the [KEY CTRL] button.
The Key Control screen will appear.
page_key_control.eps
3. Turn the [VALUE] dial.
The song’s key will change.
If key control is set to a value other than 0, the [KEY CTRL] button’s indicator will light.
Key control range
-6–0–5 (semitone units)
You can also change the key of audio that’s being input via the MIC IN jack or LINE IN jack (p. 55).
4. Press the [KEY CTRL] button to exit the screen.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
Using Minus-One and Center Cancel (MINUS ONE/CENTER CANCEL)
When playing back a song, you can use these functions to mute the specified part(s) so that you can perform it
yourself, or minimize the melodic portion so that you can perform it.
If you’ve connected a microphone or guitar, you can use the SD-50 to play back an accompaniment while
you perform on vocals or guitar.
1. Press the [MINUS ONE] (CENTER CANCEL) button so it’s lit.
The minus-one or center cancel function will turn on.
When you play back a song, the following will occur depending on the file type of the song.
File type
SMF
Function
Explanation
Minus One
Center Cancel
The sound of the specified part(s) will be muted.
Sounds in the center (the melodic portion of the sound) will be reduced.
Audio file
2. Press the [MINUS ONE] (CENTER CANCEL) button once again.
The [MINUS ONE] (CENTER CANCEL) button will go out, and the minus-one or center cancel function will be turned
off.
The center cancel function can also be applied to audio being input via the LINE IN jack (p. 55).
Changing the Minus-One part
1. Press the [MENU] button.
The menu screen will appear.
2. Turn the [VALUE] dial to select “Minus One,” and then press the [ENTER] button.
Value
Explanation
The part(s) for which this setting is ON will be muted.
PART 1–PART16: The specified part from 1 through 16 will be muted.
4&5: Parts 4 and 5 will be muted.
1&4&5: Parts 1, 4, and 5 will be muted.
EXCEPT 10: All parts except part 10 will be muted.
Normally, only the drum sound will be heard.
PART 1–PART16,
4&5, 1&4&5,
EXCEPT 10,
EXCEPT 2&10
EXCEPT 2&10: All parts except parts 2 and 10 will be muted.
3. Turn the [VALUE] dial to change the setting.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
Selecting Favorite Songs (FAVORITE)
You can register up to three songs as “favorites,” so they can later be instantly recalled at the press of a button.
Registering a Favorite Song
1. Access the song list (p. 64).
fig.page_song_list.eps
2. Press the [FAVORITE] button for a number of seconds until the REGIST SONG screen appears.
page_regist_favorite.eps
3. Press one of the [PART](1) – [PLAYER](3) buttons.
Once the following screen appears, the studio set has been saved.
page_studioset_write.eps
Selecting a Favorite Song
1. Press the [FAVORITE] button.
The registered songs will be displayed, and the [PART](1) – [PLAYER](3) button LEDs will blink.
page_favorite.eps
2. Press one of the [PART](1) – [PLAYER](3) buttons.
The corresponding favorite song will be selected.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SD-50 as an SMF/Audio Player
Adjusting the Input/Output Volume
Here’s how to adjust the playback level for an SMF or audio file, or adjust the input level for a microphone or guitar.
1. Press the [PART] button a number of times to access the audio part screen.
page_audio_meter.eps
2. Turn the [VALUE] dial to select the item that you want to edit, and then press the [ENTER] button.
The available items will differ depending on whether or not the SD-50 is connected via USB to a computer.
When not connected to a computer
page_audio_meter-2.eps
Indication
Values
0–127
0–127
0–127
Explanation
Mic/Line Input
MP3/Audio Player
SMF Player
Adjusts the level of the input to the MIC IN jack, MIC/GUITAR jack, and LINE IN jack.
Adjusts the volume of audio data playback.
Adjusts the volume of SMF playback.
When connected to a computer
Indication
Values
Explanation
Mic/Line Input
0–127
Adjusts the input level to the MIC IN jack, MIC/GUITAR jack, and LINE IN jack.
3. Turn the [VALUE] dial to edit the setting.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
System Settings
Here you can make “system” settings that apply to the overall operation of the SD-50, such as the tuning and the
brightness of the display.
Basic Procedure for System Settings
1. Press the [MENU] button.
The menu screen will appear.
menu-1.eps
2. Turn the [VALUE] dial to select the parameter that you want to edit, and then press the [ENTER]
button.
The value of the selected parameter will be highlighted.
menu-2.eps
3. Turn the [VALUE] dial to edit the value, and then press the [ENTER] button.
4. When you’ve finished making settings, press the [MENU] button.
The following message will appear.
fig.screen.eps
If you decide to cancel, press [EXIT].
5. If you decide to execute, press the [ENTER] button.
When the settings have been written, the following screen will appear, and then you’ll return to the menu screen.
menu-3.eps
72
Download from Www.Somanuals.com. All Manuals Search And Download.
System Settings
System Setting List
Indication
Range
Explanation
Adjusts the brightness of the display.
Higher settings make the display brighter.
LCD Contrast
1–10
Switches the GM sound type.
•
Classical
The basic sound set that blends well with an ensemble.
You can also choose this if GM2 data compatibility is important.
Contemporary
CLASSICAL,
CONTEMPORARY
GM TYPE
•
A sound set that emphasizes the realism of each instrument. This setting is selected
when the power is turned on.
Adjusts the tuning of the entire SD-50. The displayed value is the frequency of the A4
key (middle A).
Master Tune
Output Gain
415.3–466.2 Hz
-12– +12 dB
Adjusts the SD-50’s output gain so that the output level will be suitable when recording
to an external device.
PART 1–PART16,
4&5, 1&4&5,
EXCEPT 10,
This specifies the part(s) that will be muted when you use the Player function to play
back SMF data (p. 69).
Minus One
Battery
EXCEPT 2&10
Selects the type of battery that’s being used.
ALKALINE: Alkaline batteries
ALKALINE, Ni-MH
Ni-MH: Nickel-metal hydride batteries
This effect is provided for use on the output of the sound generator; it makes the sound
more consistent and powerful. Choose the setting that’s appropriate for your particular
song. Use this if you’re creating music that will be made into an audio CD.
SHARP: The low-frequency and high-frequency ranges will be emphasized.
CLEAR: The high-frequency range will be controlled.
OFF,
SHARP,
CLEAR, POWER
Mastering
POWER: The mid-frequency range will be emphasized.
OFF, 5min,
30min
Specifies the time after which the power will automatically turn off if the SD-50 has not
been operated.
Auto Power Off Time
Specifies the time after which the SD-50 will automatically enter power-conservation
mode if no operation has been performed. When power-conservation mode is
activated, the SD-50 will be in the following state to conserve power consumption.
OFF, 1min, 3min,
5min, 10min,
15min, 20min,
30min, 60min
Auto Save Mode
•
•
•
Display backlight will turn off
BATTERY indicator will blink
MIDI IN will not operate
Press the [ENTER] button to cancel power-conservation mode.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Functions
Utility functions let you perform various operations for the SD-50 and for USB memory.
Settings (user data) you made on the SD-50 can be saved to USB memory, and data from USB memory can be
returned to the SD-50.
Utility functions
Item
Function
Page
p. 75
p. 75
p. 76
p. 77
p. 78
BACKUP
Back up user data
RESTORE
Restore backed-up data into the SD-50
Format (initialize) USB memory
Return settings to their factory-set state
View information about the SD-50
USB MEM FORMAT
FACTORY RESET
INFORMATION
For details on the settings that can be saved as user data, refer to p. 105.
*
*
Please use USB memory sold by Roland. Operation cannot be guaranteed if any other product is used.
“BACKUP,” “RESTORE” and “USB MEM FORMAT” are not available while the SD-50 is connected via USB to a computer.
Basic Procedure
1. Press the [MENU] button.
The menu screen will appear.
menu-1.eps
2. Turn the [VALUE] dial to select “Utility.”
until-1.eps
3. Press the [ENTER] button.
The utility screen will appear.
until-1.eps
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Functions
Backing Up User Data (BACKUP)
Here’s how to save user data to USB memory. This operation is called “backup.”
1. Connect your USB memory device to the SD-50.
2. In the utility screen, select “User Backup.”
page_util-back.eps
3. Press the [ENTER] button.
The following screen will appear.
back-up-dialog.eps
To cancel without executing, press the [EXIT] button.
4. To execute the backup, press the [ENTER] button.
When the backup is completed, the following screen will appear.
page_utilback-up-comp.eps
For details on the user data settings that are saved, refer to p. 105.
Restoring Backed-Up Data to The SD-50 (RESTORE)
Here’s how user data backed-up to USB memory can be returned to the SD-50. This operation is called “restore.”
1. Connect the USB memory device containing your backup data to the SD-50.
2. In the utility screen, select “User Restore.”
page_util-rest.eps
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Functions
3. Press the [ENTER] button.
The following screen will appear.
Restore-dialog.eps
To cancel without restoring, press the [EXIT] button.
4. To execute the restore operation, press the [ENTER] button.
When the restore is completed, the following screen will appear.
page_power_off.eps
5. Turn the SD-50’s power off, then on again.
Formatting USB Memory (USB MEM FORMAT)
Here’s how to format USB memory.
If the USB memory contains important data, be aware that formatting USB memory will cause all data saved on
that USB memory to be lost.
1. Connect your USB memory device to the SD-50.
2. In the utility screen, select “USB Mem Format.”
page_util-foramt.eps
3. Press the [ENTER] button.
The following screen will appear.
formar-dialog.eps
To cancel without formatting, press the [EXIT] button.
4. To execute the format operation, press the [ENTER] button.
When formatting is completed, the following screen will appear.
page_util-for-comp.eps
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Functions
Returning to the Factory Settings (FACTORY RESET)
Here’s how you can return all settings in the SD-50 to their factory-set condition. This operation is called “factory reset.”
If the SD-50 contains important data you’ve created, be aware that all of your data will be lost when the factory
reset operation is executed.
If you want to keep your data, save it to USB memory before you proceed.
1. In the utility screen, select “Factory Reset.”
page_util-fact.eps
2. Press the [ENTER] button.
The following screen will appear.
page_power_off.eps
To cancel without executing, press the [EXIT] button.
3. To execute the factory reset operation, press the [ENTER] button.
When the factory reset has been completed, the following screen will appear.
page_power_off.eps
4. Turn the SD-50’s power off, then on again.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Functions
Viewing Information About the SD-50 (INFORMATION)
Here’s how to view the version of the SD-50’s system software, and the remaining battery power.
1. In the utility screen, select “INFORMATION.”
page_util-infor.eps
2. Press the [ENTER] button.
The following screen will appear.
page_system_info.eps
Press the [EXIT] button to return to the previous screen.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling DAW Software
When the SD-50 is connected to your computer, you can use the SD-50 to control your DAW software. For example,
you can press the SD-50’s [
fig.connect-MIDI-Cont_e.eps
] button to play a song in your DAW software.
Computer
MIDI Signal flow
SD-50
Press
The MIDI messages transmitted from the SD-50 are compatible with Mackie Logic Control.
As described in the owner’s manual of your DAW software, set your DAW software so that it can be controlled by the
following MIDI messages.
Button operation
Transmitted MIDI message
[
[
[
[
] button
] button
Press
Press
Press
Press
90 5D 00
Release
Release
Release
Release
90 5D 7F
90 5E 7F
90 5B 7F
90 5C 7F
90 5E 00
90 5B 00
90 5C 00
] button
] button
Hold down the [EXT] button and
turn the [VALUE] dial
Clockwise
B0 3C 01
Counterclockwise
B0 3C 41
80
Download from Www.Somanuals.com. All Manuals Search And Download.
About V-LINK
What is V-LINK?
V-LINK (
) is a function that lets you present music and video simultaneously. When V-LINK
compatible devices are connected via MIDI, you’ll be able to easily enjoy a variety of visual effects that are linked to
the expressive elements of your performance.
For example, if you use the SD-50 with the EDIROL P-10, you’ll be able to do the following.
•
•
Use the various controllers of the SD-50 console to switch and control images on the EDIROL P-10.
In order to enjoy V-LINK with the SD-50 and the EDIROL P-10, you’ll need to make connections using MIDI cables (sold
separately).
Example Connection
Here we explain an example of connecting the SD-50 to the EDIROL P-10. Use a MIDI cable to connect the SD-50’s
MIDI OUT connector to the EDIROL P-10’s MIDI IN connector.
*
To prevent malfunction and speaker damage, you must minimize the volume on all equipment and turn off their
power before you make any connections.
fig.connection-V-LINK_e.eps
MIDI cable
MIDI OUT
MIDI IN
SD-50
EDIROL P-10
81
Download from Www.Somanuals.com. All Manuals Search And Download.
About V-LINK
Turning V-LINK On/Off
1. Press the [V-LINK] button.
The button will light, and the following screen will appear.
fig.screen_vlink.eps
V-LINK will turn on.
When the V-LINK button is on, the video can be controlled in tandem with operations of the SD-50.
2. Press the [V-LINK] button once again.
The V-LINK button will go out, and V-LINK will turn off.
Controllers Used with V-LINK
Button operation
V-LINK function
Transmitted MIDI message
Press the [TEMPO] button
Press the [KEY CTRL] button
Press the [MINUS ONE] button
Switch images (switch clips)
Switch images (switch clips)
Switch images (switch clips)
Switch images (switch clips)
Switch images (switch clips)
Switch images (switch clips)
Switch images (switch clips)
Switch images (switch clips)
C0 00
C0 01
C0 02
C0 03
C0 04
C0 05
C0 06
C0 07
Press the [
Press the [
Press the [
Press the [
Press the [
] button
] button
] button
] button
] button
Press the [PART] button and then
turn the [VALUE] dial
Control the image Image Bank Select
Control the image Color Cr Control
Control the image Playback Speed
B0 00 00–13
B0 47 00–7F
Press the [INST] button and then
turn the [VALUE] dial
Press the [PLAYER] button and
then turn the [VALUE] dial
E0 00 00–40 00–7F 7F
-8192–0–8191
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver Settings
The settings window of the SD-50 driver allows you to make settings such as the audio input/output buffer size.
Decreasing the buffer size will decrease the latency and improve the realtime response. However, depending on the
processing power of your computer and the complexity of your song data, this may make clicks and pops during
recording or playback more likely.
Increasing the buffer size will increase the latency, but will make audio data transfer more stable, decreasing the
likelihood of clicks and pops.
If you’re playing a software synthesizer in real time or using your DAW software to monitor the “thru” signal of the
audio input, you should decrease the buffer size in order to improve the realtime response.
Conversely, if you’re recording or playing back song data that contains numerous tracks and imposes a heavy
processing load on your computer, you should increase the buffer size in order to decrease clicks and pops.
Change the buffer size as appropriate for your situation in order to achieve a balance between realtime response and
audio data transfer, while avoiding problems such as clicks and pops.
Windows Users
*
If the Windows monitoring function is enabled, it won’t be possible to change the driver settings on Windows 7.
Refer to “Windows Monitoring Function Settings (Windows 7)” (p. 103) and disable monitoring.
1. Use a USB cable to connect the SD-50 to your computer, then switch on the SD-50’s power.
2. Open the Control Panel, then change the method of display to Icon View (Windows 7) or to Classic
View (Windows Vista/Windows XP).
3. Double-click the SD-50 icon that appears.
The SD-50 Driver Settings dialog box will appear.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver Settings
About the Items in the Settings Dialog Box
fig.driver-e.eps
1
2
3
4
5
6
7
No.
Setting
Description
This lets you adjust the buffer size for the audio input/output. (The default setting is
the sixth position from the left.)
*
If you change the buffer size, you must restart the application that’s using the SD-50,
or if you’re using an application that has an audio device test function, you must
execute that test function.
Audio Buffer Size
1
*
Depending on the application that you’re using, its audio settings may also contain
a buffer size adjustment.
This is the minimum buffer size that can be specified for an ASIO application.
*
Depending on the application you’re using, there may be settings other than the
minimum buffer size, meaning that in some cases the buffer size shown here might
not match the actual buffer size.
ASIO Buffer Size
2
3
For details on how to set and view the buffer size, refer to the owner’s manual for
your application.
By selecting this check box, you can decrease the buffer size when using ASIO
compatible software.
If you experience dropouts in the sound with this check box selected, clear the check
box.
Use Smaller ASIO Buffer Size
*
Clear this check box if you want to adjust the Audio Buffer Size.
Select this check box if you want to use ASIO Direct Monitor functionality with your
ASIO compatible software.
Use ASIO Direct Monitor
Light Load
4
5
Normally, you should leave this check box cleared.
*
A setting change will take effect after you’ve switched off the SD-50’s power, then
switched it back on again.
Show “README”
Driver version
Displays the README file.
6
7
This displays the version of the currently installed driver.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver Settings
MAC OS X Users
1. Use a USB cable to connect the SD-50 to your computer, then switch on the SD-50’s power.
2. In “System Preferences,” click “SD-50.”
The Driver Settings screen will appear.
About the Items in the Settings Dialog Box
fig.Driverset-mac-e.eps
1
2
3
No.
Setting
Description
This adjusts the driver’s audio input/output buffer size.
If you experience dropouts or noise when playing or recording even after you have
adjusted the audio buffer size in your software, try increasing this buffer size setting.
Audio Buffer Size
1
*
Some software does not allow you to adjust the buffer size.
If there are dropouts or noise in the recorded audio data even after you have adjusted
the audio buffer size in your software and have also adjusted the Audio Buffer Size, try
increasing this recording margin setting.
Recording Margin
Recording Timing
2
3
*
Some software does not allow you to adjust the buffer size.
Adjust this setting if the timing of the recorded audio data is incorrectly aligned.
*
If audio software is running, these settings will not be applied immediately even if
you click [Apply]. Close all audio software; the settings will be applied the next time
you start up the software.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Reinstalling the Driver
If a problem occurred while installing the driver, use the following procedure to reinstall it.
1. Uninstall the SD-50 driver as described in “Removing the driver.”
2. Install the driver once again as described in “Installing the Driver” (p. 23).
Removing the Driver
Your computer may fail to correctly recognize the SD-50 if the driver could not be installed according to the specified
procedure. If so, use the following procedure to remove the driver, and then install the driver once again according to
the procedure given in “Installing the Driver” (p. 23).
*
The displayed content may differ depending on your system.
Windows Users
1. Start up Windows with the SD-50 disconnected.
Make sure that all USB cables other than those for a USB keyboard and USB mouse (if used) are disconnected.
Log on using a user name whose account type is computer administrator (such as Administrator).
2. Insert the included Mobile Studio Canvas DVD-ROM into your computer’s DVD-ROM drive.
3. On the DVD-ROM, navigate to the following folder and double-click [Uninstal].
OS
Folder
Windows 7
Open the folders [Driver] and then [Win7]
Open the folders [x64Driver] and then [Win7]
Open the folders [Driver] and then [Vista]
Open the folders [x64Driver] and then [Vista]
Open the folders [Driver] and then [XP]
Windows 7 64-bit edition
Windows Vista
Windows Vista 64-bit edition
Windows XP
4. If a user account control message appears, click [Yes] or [Continue].
5. The screen will indicate “The installed SD-50 Driver will be uninstalled.” Click [OK].
If any other message appears, proceed as directed by the message.
6. The screen will indicate “Uninstallation was completed.” Click [OK] to restart Windows.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Reinstalling the Driver
Mac OS X Users
1. Start up your computer with all USB cables disconnected.
Make sure that all USB cables other than those for a USB keyboard and USB mouse (if used) are disconnected.
2. Insert the included DVD-ROM into the DVD-ROM drive of your computer.
3. Double-click one of the following icons on the DVD-ROM to start up the uninstaller.
OS
Uninstaller
Mac OS X 10.6 or later
Mac OS X 10.5 or earlier
[SD50_Uninstaller] (/Driver/10.6)
[SD50_Uninstaller] (/Driver/10.4_10.5)
4. The screen will indicate “This uninstalls SD-50 driver from this Macintosh”. Click [Uninstall].
If any other message appears, proceed as directed by the message.
5. The screen will indicate “Are you sure to uninstall the driver?” Click [OK].
6. An Authenticate dialog box or the dialog that asks to type your password will appear. Enter the
password and click [OK].
7. The screen will indicate “Uninstallation is completed.” Click [Restart] to restart your computer.
*
It may take some time for the computer to restart.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you experience a problem, read this chapter first. It contains information that may help you solve the problem. If the information here
does not help you solve the problem, try accessing the Roland website. If you are still unable to solve the problem, please contact a
service location listed at the end of this manual.
Problems Using The SD-50 as a Player
•
Is the SD-50 connected to a computer?
The Player function cannot be used when the SD-50 is
connected to a computer. Nor is it possible to play the
SD-50’s sound generator via the MIDI IN connector.
Overall
Power will not turn on
•
Make sure that the SD-50’s AC adaptor is correctly connected
to an outlet and to the SD-50 (p. 20).
No sound from a specific part
Check the following points.
•
Check to see if you have enough battery power remaining (p.
21).
•
Could the volume of that part be turned down?
Raise the Level setting of that part to increase the volume
(p. 50).
Problems with the Sound
•
Could the part be set to “M” (Mute)?
Change the setting to “-” (p. 49).
No sound
Sound is distorted
Check the following points.
Check the following points.
•
Are the connected amp and speaker powered up? Could the
volume be lowered?
•
•
If the overall sound is distorted, use [VOLUME] dial to lower
the volume.
•
•
•
•
Are the connections correct?
Could the Output Gain be raised excessively?
Check the system setting Output Gain (p. 73).
Can you hear sound through headphones?
the connection cables are broken, or that your amp or
speaker has malfunctioned. Check the cables and your
equipment once again.
Pitch is incorrect
Check the following points.
•
•
Could the SD-50’s tuning be incorrect?
Check the Master Tune setting (p. 73).
•
•
Could the part level settings have been minimized?
Check the level of each part (p. 50).
Could the pitch have been changed by a pitch bend message
received from an external MIDI device?
Are the effect settings appropriate?
Check the effect on/off, effect balance, and level settings
(p. 50).
Notes are interrupted
•
If a large number of notes are played, notes might be
interrupted.
Reduce the number of tones being used.
•
Could a MIDI message received from an external MIDI device
(volume message or exclusive message) have lowered the
volume?
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
This means that even if these are set to their maximum value
of 127, there will be no effect if the send level of the patch
you’re using has been lowered.
Even though you set a tone’s pan all the way to
one channel, sound is still heard from the
opposite channel
If you want to apply the effect more deeply, you’ll need to
edit the settings of the patch. The patch’s send levels to
chorus and reverb can be specified separately depending on
whether you’re using multi-effects.
The SD-50’s built-in effects are stereo. This means that if
you’ve applied an internal effect, the effect sound will still be
heard from the opposite channel even if a tone is panned all
the way to one side.
Problems when Saving Data
The sound becomes strange when you play high
notes
Playing high notes on the SD-50 might produce an
unexpected result, including no sound at all, failure of the
sound to go higher in pitch, or noise that changes depending
on the key you play (warbling, chirping, beeping, buzzing,
etc.)
This is mainly caused by exceeding the limit of high notes
that the SD-50 is able to produce; this occurs for notes that
are not normally played, and does not indicate a malfunction.
Settings are different than those saved in the
studio set
Check the following points.
•
The settings of the mastering effect may have changed.
(These settings are not included in the studio set.)
Problems with MIDI and External Devices
Insufficient volume from a device connected to
the SD-50’s INPUT
Playback on your external sequencer lags or is
interrupted
Could you be using a connection cable that contains a built-
in resistor?
Use a connection cable that does not contain a resistor.
If the playback lags or is interrupted, it is likely that the
sequencer or sound module is experiencing a heavy
processing load.
Here are the main causes and what you can do about them.
Problems with Effects
•
•
Could the polyphony be exceeding 128?
Try reducing the number of notes that are played
simultaneously.
Effect not applied
Could a large amount of data be concentrated at the
beginning of a beat in the sequence data?
Try staggering the timing by one or two clocks so that data
does not occur at the same timing.
It’s easy for song data to be concentrated at the beginning of
a beat if you use step recording to create song data, or if you
apply quantization after real-time recording from a keyboard.
This may cause a large amount of data to be transmitted to
the SD-50 at the same time, causing playback to lag.
Check the following points.
•
•
Are the various effect settings appropriate? (p. 51)
There will be no effect if the corresponding effect’s send level
is at 0. Check the settings.
•
Even if the effect’s send level is above 0, there will be no
effect if the multi-effect output level, chorus level, or reverb
level are at 0. Check these settings.
•
Could there be program changes at the locations where the
playback lags?
Try changing the location of the program change data.
If you insert program changes in your song, processing time
may be required in order to switch tones, causing the
playback to lag.
The effect is difficult to notice even if you raise
the chorus or reverb send level of each part
The send level to the chorus and reverb effects can be
specified for each part, but these values specify the amount
that will be used of the patch’s own chorus and reverb send
levels.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
•
Could there be system exclusive data at the locations where
the playback lags?
Problems with External Input
Try changing the location of the system exclusive data. Since
system exclusive messages involve a large amount of data,
they can place a significant processing load on the sequencer
or sound module.
No sound (or insufficient volume) from a device
connected to MIC/GUITAR IN or LINE IN
Try changing the location of the data, or if possible, replace
the system exclusive data with a control change.
Check the following points.
•
Are the audio cables connected correctly?
Check the connections.
•
Could there be a large amount of control change data (such
as aftertouch) at the locations where the playback lags?
Try changing the location of the data. If you don’t need the
data, delete it.
If the keyboard you use for recording is transmitting
aftertouch messages, a large amount of aftertouch data may
be recorded without your noticing.
•
•
Could an audio cable be broken?
Could you be using a connection cable that contains a
resistor?
Use a connection cable that does not contain a resistor.
•
•
Could the [SENS] knob be set to “MIN”?
Adjust the level appropriately.
This large amount of data can place an excessive processing
load on the sequencer or sound module.
Is the [SETTING] switch at the appropriate position?
Set the [SETTING] switch as appropriate for the device that’s
connected.
You’ve connected an external sequencer or MIDI
keyboard to the MIDI IN connector and are
attempting to play the SD-50’s sounds, but you
don’t hear anything
No sound from the microphone
•
Could you have connected a condenser microphone?
If you’re using a condenser microphone, you’ll need to supply
phantom power to it.
Check the following points.
•
•
Make sure that the external MIDI device’s MIDI transmit
channel matches the SD-50’s MIDI receive channel.
Set the [SETTING] switch to “DC 48 V 10 mA” (p. 56).
Could the microphone cable be broken?
•
Could the SD-50 be connected via USB to your computer?
If you’ve connected the SD-50 to a computer and are trying
to use an external device to play the SD-50’s sound
generator, you should switch on your software’s “MIDI Thru”
setting.
The bend range is set to the maximum, but the
pitch does not rise all the way when pitch bend
messages are received via MIDI
The bend range can be set in the range of 0–24, but
depending on the wave that’s used, there are cases in which
the pitch will not rise all the way; i.e., the pitch might stop
rising at a certain pitch.
Sounds are guaranteed to rise through a bend range setting
of 12, but please be aware that bend range settings greater
than this are not guaranteed to work.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Song does not play
Problems with USB Memory
This might be due to one of the following reasons.
Is a “?” symbol shown in the list of songs for the playlist?
The song’s file type is not one that the SD-50 can play.
The song data might be damaged.
•
•
•
•
USB memory is not recognized
Files are not displayed
•
It may be that the USB memory has not been formatted
correctly. If the USB memory was formatted by a device other
than the SD-50, use the SD-50 to format it (p. 76).
The song cannot be played if you directly add/delete/modify
the song data in the SD-50 folder without using Playlist
Editor.
Can’t back up to USB memory
Can’t hear the playback
Check the following points.
•
Is the playback volume set correctly?
•
•
Could the USB memory be write protected?
Go to the play screen and adjust the playback volume (p. 66).
Does the USB memory has sufficient free space?
Problems with Songs
Playlist is not displayed
This might be due to one of the following reasons.
•
The playlist might not be displayed if you directly add/delete/
modify the song data in the SD-50 folder without using
Playlist Editor.
•
It may be that the USB memory has not been formatted
correctly. If the USB memory was formatted by a device other
than the SD-50, use the SD-50 to format it (p. 76).
Songs are not displayed
This might be due to one of the following reasons.
•
•
Is the song located in the root directory?
The song might not be displayed if you directly add/delete/
modify the song data in the SD-50 folder without using
Playlist Editor.
•
It may be that the USB memory has not been formatted
correctly. If the USB memory was formatted by a device other
than the SD-50, use the SD-50 to format it (p. 76).
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problems that Can Occur when Connected to a Computer
For help with Windows or Mac OS X operation, refer to the documentation for your computer or operating system.
Problems when Installing the Driver
Are there any devices labeled “Other,”
“Unknown,” or “?/!/X” in the Device Manager?
Can’t start up the installer
Is the DVD-ROM inserted correctly in your DVD-
ROM drive?
If driver installation was not completed successfully, the
partially installed driver may remain in an incomplete state.
Make sure that the DVD-ROM is correctly inserted in the DVD-
ROM drive.
Reinstall the SD-50 driver as described in “Reinstalling the
Driver” (p. 86).
Could the DVD-ROM itself or the lens of your
DVD-ROM drive be dirty?
Can’t install the driver
Did you log on to Windows with the appropriate
user privileges?
The installer may not operate correctly if the DVD-ROM or the
lens of your DVD-ROM drive is dirty. Use a commercially
available CD cleaner or lens cleaner to clean the disc or lens.
You must log onto Windows using one of the following user
names.
•
A user name belonging to the Administrators group, such as
Administrator
Are you attempting to install from a networked
DVD-ROM drive?
•
For details, ask the system administrator for your computer.
The driver cannot be installed from a DVD-ROM drive on the
network.
*
A warning or error appears during the
driver because of the “Driver signing option”
settings (Windows XP)
Could you have connected the SD-50 to your
computer before installing the driver?
Refer to “Driver Signing Option Settings (Windows XP)” (p.
99) and make the appropriate settings.
If you connect the SD-50 to your computer before installing
the driver, an error message may appear when you begin the
installation.
Reinstall the SD-50 driver as described in “Reinstalling the
Driver” (p. 86).
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Could other software be running, perhaps in the
background (such as anti-virus software)?
“Found New Hardware Wizard” appears even
though you’ve installed the driver
(Windows XP)
The installation may not occur correctly if other software is
running. Be sure to close all other software before you
perform the installation.
Could you have connected the SD-50 to a
when installing the driver?
Installation is not successfully completed
If your computer or USB hub has two or more USB
connectors, connecting the SD-50 to a different USB
connector may cause your computer to ask for the driver file
even though the driver has already been installed.
After you connect the SD-50, it may take several
minutes before it is recognized by your computer
This is not a malfunction.
This behavior does not indicate a malfunction.
Please wait until the Found New Hardware Wizard appears.
Install the driver as described in step 9 of Installing the driver
(p. 23).
Is the SD-50 connected?
Make sure that the SD-50 is correctly connected to your
computer.
A number such as “2-” appears at the
beginning of the device name (Windows)
Could your computer be operating on its battery?
Could you have connected the SD-50 to a
Operation may be unstable if your computer is operating on
battery power.
If you connect the SD-50 to a different USB port, some
operating systems may automatically add a number to the
beginning of the device name, but this should not be a
problem when using the SD-50. If you want to return to the
device name that does not have this number, you can either
connect the SD-50 to the same USB port as when you
installed it, or install the driver once again.
Please use your computer with its power supply connected.
Could a USB device other than a mouse or
keyboard be connected?
Disconnect all USB devices (other than a mouse and
keyboard, if used) from your computer before performing the
installation.
➝ “Reinstalling the Driver” (p. 86)
Does your computer meet the requirements of
the USB specification?
Operation may be unstable if your computer does not meet
the electrical requirements of the USB specification.
In this case, you may be able to solve the problem by
connecting a self-powered USB hub (a USB hub that has an
internal power supply or an AC adaptor).
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problems with Settings
Could the SD-50 have been connected when the
computer started up?
Can’t select/use the SD-50 within software or
in system settings
On some computers, the SD-50 may be unusable if it is
already connected when the computer starts up.
Could the SD-50 be in use by other software?
the SD-50’s power, then turn it back on again.
Start up your computer, and then connect the SD-50.
If this does not solve the problem, reinstall the driver.
with Windows?
➝ “Reinstalling the Driver” (p. 86)
The SD-50’s MIDI device cannot be selected for Media Player
on Windows 7 or Windows Vista.
Driver installation may have failed. Please reinstall the driver.
➝ “Reinstalling the Driver” (p. 86)
Have you made “Audio MIDI Settings”? (Mac OS X)
Make the appropriate Audio MIDI Settings as described in
“Mac OS X Users” (p. 33).
Is the SD-50 device name shown?
If the device name is not displayed, it may be that the driver
installation failed. Please reinstall the driver.
Can’t make driver settings (Windows 7)
➝ “Reinstalling the Driver” (p. 86)
Could the monitoring function of Windows be
enabled?
Could the computer to which the SD-50 is
connected have entered standby (suspend)
mode, hibernate mode, or sleep mode?
Refer to “Windows Monitoring Function Settings (Windows
7)” (p. 103) and disable the monitoring function.
Close all software that’s using the SD-50. Next, switch off the
SD-50’s power, then turn it back on again.
If this does not solve the problem, restart your computer.
Could you have disconnected and reconnected
the USB cable while using the SD-50?
Close all software that’s using the SD-50. Next, switch off the
SD-50’s power, then turn it back on again.
If this does not solve the problem, restart your computer.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problems with Playback or Recording
Could you have disconnected and reconnected
the USB cable while using the SD-50?
Can’t play or record
Was the driver installed correctly?
Driver installation may have failed. Reinstall the driver.
Close all software that uses the SD-50, disconnect the SD-50’s
USB cable, and then reconnect it.
If this does not solve the problem, restart your computer.
Could you have connected or disconnected the
USB cable during playback or recording, or
switched off the SD-50, then turned it back on
again?
Refer to the owner’s manual of your software and to the
following pages, and select the SD-50 as the input/output
device.
If you disconnect and reconnect the USB cable during
playback or recording, or switch off the SD-50, then turn it
back on again, the SD-50 may become unable to play back or
record. Stop playback or recording, and then perform
playback and recording again.
•
Windows 7/Windows Vista:
➝ “Input/Output Device Settings” (p. 26)
Windows XP: ➝ “Input/Output Device Settings” (p. 31)
•
•
Mac OS X:
➝ “Audio input/output device settings” (p. 34),
If you are still unable to play back or record, close all
applications that are using the SD-50, and then turn the
SD-50’s power off, then on again.
“MIDI input/output device settings” (p. 35)
Could the SD-50 be in use by other software?
Close all software that’s currently running, disconnect the
SD-50’s USB cable, and then reconnect it.
Could the SD-50 have been connected when the
computer started up?
If this does not solve the problem, reinstall the driver.
On some computers, the SD-50 may be unusable if it is
already connected when the computer starts up.
➝ “Reinstalling the Driver” (p. 86)
Start up your computer, and then connect the SD-50.
Could the computer to which the SD-50 is
connected have entered standby (suspend)
mode, hibernate mode, or sleep mode?
Could there have been a heavy processing load
while using the SD-50?
Close all software that uses the SD-50, disconnect the SD-50’s
USB cable, and then reconnect it.
If your computer experiences a heavy processing load while
you’re using the SD-50, it may stop operating correctly. If this
occurs, stop playback/recording, and then perform playback/
recording again.
If this does not solve the problem, restart your computer.
If you are still unable to play back or record, close all
applications that are using the SD-50, and then turn the
SD-50’s power off, then on again.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
No sound from your computer’s speakers
microphone
If you connect the SD-50 to your computer, sound
will not be heard from your computer’s speakers
Is the [SETTING] switch set correctly?
This is not a malfunction.
Check the [SETTING] switch (p. 56).
Connect your headphones or audio playback system
(external monitors) to the SD-50.
Is the input level appropriate?
Try turning the SD-50’s [SENS] knob toward the right to
increase the input level (p. 56).
Sound played by your computer is inaudible
or too soft
Could you be using a cable that contains a
resistor?
Can you hear sound by connecting headphones?
If you can hear sound through headphones connected to the
SD-50’s headphone jack, check that you have correctly
connected your audio playback system (external monitors),
and adjust the volume of your equipment.
Make connections using a cable that does not contain an
internal resistor.
Playback contains clicks, dropouts, or other
problems
If the sound in your headphones is inaudible or too soft,
check the other troubleshooting items.
Try adjusting the audio buffer size of your
software
Are the volume settings of the SD-50 itself set
appropriately?
If your software allows you to adjust the audio buffer size, try
changing the setting. Normally, clicks and pops can be
Use the SD-50’s [VOLUME] dial to adjust the volume.
Could the Windows or Macintosh system volume
be turned down?
Try adjusting the audio buffer size of the driver
Set the volume of your computer system to the appropriate
level.
If your software does not allow you to adjust the buffer size,
or if adjusting the buffer size in your software does not solve
the problem, you may be able to solve the problem by
➝ “System Volume Settings” (p. 102)
Try adjusting the buffer size as described in “Driver Settings”
(p. 83).
Could you be using voice communication
software? (Windows 7)
If you’re using voice communication software, the volume of
the audio device might be automatically adjusted according
to the status of your conversation.
Try increasing the “Recording margin” (Mac OS X)
If there are still clicks and pops in the recorded audio data
even after you’ve adjusted the audio buffer size, try
increasing the “Recording margin” as described in “About
the Items in the Settings Dialog Box” (p. 85).
In this case, disable the automatic volume adjustment.
➝
“Voice communication Software Settings (Windows 7)”
(p. 103)
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Check the power management settings
Try disabling the LAN
You may be able to eliminate clicks and pops by changing
your system’s power management settings.
In your computer’s Device Manager, try disabling LAN (wired/
wireless).
➝ “Power Management Settings” (p. 100)
If this eliminates the clicks and pops, it may be that updating
your LAN driver or BIOS may solve the problem. Check
whether updated software is available.
Try updating the driver of your display adaptor
(Windows)
Could you have connected the SD-50 to a USB hub?
You may be able to eliminate clicks and pops by updating the
driver for the display adaptor installed in your computer.
Try connecting the SD-50 directly to a USB connector on your
computer.
Have you set the system’s “Performance” setting?
(Windows)
Are you using the included USB cable?
You must use the included USB cable when using the SD-50.
Some commercially available USB cables do not meet the
requirements of the USB standard, and this may prevent the
SD-50 from operating correctly.
You may be able to solve the problem by changing the
“Performance” setting of the system.
➝ “System “Performance” Settings (Windows)” (p. 101)
Could other software programs be running?
Could you have updated the Mac OS X software
while SD-50 was connected?
Close software that you’re not using.
If the window of a Windows program has been closed but it is
still shown in the taskbar, that program is still running. Close
all unneeded software that’s shown in the taskbar.
It has been found that clicks or pops can occur if you
performed a Mac OS X software update while the SD-50 was
Have you tried Windows Update or Microsoft
Could the monitoring function of Windows be
Try using Windows Update or Microsoft Update (provided by
the Microsoft Corporation) to update your system to the
latest version.
If the monitoring function of Windows is enabled, the input
sound might be heard in duplicate (doubled) or as a loop
(feedback).
In this case, disable the monitor function of Windows.
➝
“Windows Monitoring Function Settings (Windows 7)”
(p. 103)
In the driver settings dialog box, try selecting the
“Light Load” check box
To view or change the settings, proceed as described in
“Driver Settings” (p. 83).
Click or pops may occur in the playback/recording
immediately after you start up your computer, or
immediately after it has been waken from sleep
This change will take effect after you turn the SD-50’s power
off, then on again. Unless you are experiencing problems,
you should leave this check box cleared (the default state).
Please wait for a while before you play back or record.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Try adjusting “Hardware Acceleration” in the
advanced display properties (Windows XP)
In some cases, adjusting your graphics acceleration settings
may solve problems with noise during audio playback.
➝ “Hardware Acceleration Settings (Windows XP)” (p. 99)
Noise or distortion occurs elsewhere than in
the playback from your computer
Is a guitar connected?
If the noise decreases when you lower your guitar’s volume, it
may be that your guitar’s pickups are being affected by noise
from your computer or display. Move the guitar as far away
from your computer as possible.
Could you have left an unused microphone or
guitar connected?
If an unused microphone or guitar is connected to the SD-50,
disconnect the microphone or guitar, and turn the [SENS]
knob to MIN in order to lower the input level.
Have you connected the ground terminal?
You may be able to solve the problem by grounding a metal
component of your computer or the ground pin of your
computer’s AC adaptor. Also check whether there might be a
device nearby that is emitting a strong electromagnetic field,
such as a television or microwave oven.
Recorded sound is too loud or too soft
Is the input level appropriate?
Use the SD-50’s [SENS] knob to adjust the input level. If your
software is able to adjust the input level, check its input level
setting.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Settings for Your Computer that Can Prevent Problems
This section explains how to make settings on your computer to avoid the problems described in “Problems that Can Occur when
Connected to a Computer” (p. 92).
Driver Signing Option Settings
(Windows XP)
Hardware Acceleration Settings
(Windows XP)
Driver installation may not be possible due to your settings
for “Driver Signing Options.” Refer to the following, and make
the appropriate settings.
In some cases, adjusting your graphics acceleration setting
may solve problems with noise during audio playback.
1. Open the “Control Panel,” and double-click
[Display].
1. Open the “Control Panel,” click [Performance and
Maintenance], and then click the [System] icon.
If you’re using the Classic view, double-click [System].
If you don’t see the above icon, click “Desktop view and
themes,” and then click [Display].
2. Click the [Hardware] tab, and then click [Driver
Signing].
2. Click the “Settings” tab.
3. From [Advanced Settings], click the
[Troubleshooting] tab.
The “Driver Signing Options” dialog box will appear.
3. In the “Driver Signing Options” dialog box, choose
[Warn] or [Ignore], and click [OK].
4. Adjust the “Hardware Acceleration” slider, and
click [OK].
4. Click [OK] to close the “System Properties” dialog
box.
5. In “Display Properties,” click [OK] to close the
dialog box. Then restart your computer.
5. Install the driver as described in the procedure for
“Windows XP Users” (p. 28).
6. Restart Windows.
Once you’ve finished installing the driver, change the driver
signing options back to their original settings.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Windows Vista users
Power Management Settings
1. Open the “Control Panel,” click [System and
Maintenance], and then click [Power Options].
If you experience problems such as interrupted notes or
dropouts in the sound, you may be able to solve the problem
by changing your computer’s power management settings.
If you’re using the Classic view, double-click the [Power
Options] icon.
Windows 7 users
2. In “Select a power plan,” choose [High
performance].
1. Open the “Control Panel,” click [System and
Security], and then click [Power Options].
3. In the [High performance] area, click [Change plan
settings].
If you’re using an icon display, double-click the [Power
Options] icon.
4. Click [Change advanced power settings].
2. In “Select a power plan,” choose [High
performance].
5. In “Power Options” [Advanced Settings], click the
[+] symbol for “Hard Disk,” and click the [+] symbol
for “Turn off hard disk after” to open it.
3. In the [High performance] area, click [Change plan
settings].
6. Click [Setting (Minutes)], and click the down arrow
to change the setting to [Never].
If you don’t see [High performance], click [Show additional
plans].
4. Click [Change advanced power settings].
7. Click [OK] to close the “Power Options” window.
8. Close the “Edit Plan Settings” screen.
5. In “Power Options” [Advanced Settings], click the
[+] symbol for “Hard Disk,” and click the [+] symbol
for “Turn off hard disk after” to open it.
Windows XP users
6. Click [Setting (Minutes)], and click the down arrow
to change the setting to [Never].
1. Open the “Control Panel,” click [Performance and
Maintenance], and click [Power Options].
7. Click [OK] to close the “Power Options” window.
8. Close the “Edit Plan Settings” screen.
If you’re using the Classic view, double-click the [Power
Options] icon.
2. Click the [Power Schemes] tab, and in the “Power
Schemes” field, select [Always On].
3. Click [OK] to close “Power Options Properties.”
2. Click [Options].
Mac OS X users
*
Depending on the version of Mac OS X that you use, you may
not be able to make the setting below.
3. In the “Processor Performance” field, choose
[Highest].
1. In “System Preferences,” click [Energy Saver].
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Windows Vista users
System “Performance” Settings
(Windows)
1. Open the “Control Panel,” click [System and
Maintenance], and click [System].
You may be able to solve the problem by changing the
“Performance” setting of the system as described below.
If you’re using the Classic view, double-click the [System]
icon.
2. In the list of “tasks” shown at the left, click
[Advanced System Settings].
Windows 7 users
1. Open the “Control Panel,” click [System and
Security], and click [System].
3. A User Account Control dialog box will appear; click
[Continue].
If you’re using an icon display, double-click the [System] icon.
If you’re asked to enter an administrator password, log on to
Windows as a user whose account type is administrator, and
make the setting again.
2. At the left, click [Advanced system settings].
3. A User Account Control dialog box will appear; click
[Yes].
4. Click “Performance” [Settings], and click the
[Advanced] tab.
If you’re asked to enter an administrator password, log on to
Windows as a user whose account type is administrator, and
make the setting again.
5. Choose [Background services] and click [OK].
6. Click [OK] to close System Properties.
4. Click “Performance” [Settings], and click the
[Advanced] tab.
Windows XP users
5. Choose [Background services] and click [OK].
6. Click [OK] to close “System Properties.”
1. Open the “Control Panel,” click [Performance and
Maintenance], and click [System].
If you’re using the Classic view, double-click the [System]
icon.
2. Click the [Advanced] tab, and click “Performance”
[Settings].
3. Click the [Advanced] tab.
4. Choose [Background services], and click [OK].
5. Click [OK] to close “System Properties.”
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Windows XP users
System Volume Settings
1. Open the “Control Panel,” and double-click
[Sounds and Audio Devices].
Windows 7 users
If you’re using the Classic view, double-click “Sounds and
Audio Devices.”
1. Open the “Control Panel,” and switch “View by:” to
“Category.”
2. Click the [Audio] tab.
2. Click [Hardware and Sound], and then click [Adjust
system volume].
3. In the “Sound playback” area, make sure that [OUT
(SD-50)] is selected as the “Default device,” and
click [Volume].
3. The volume mixer will appear. From the pulldown
menu of the “Device” item, choose the SD-50’s
[OUT], and adjust the volume.
4. The Volume Control will appear; adjust the Wave
volume.
You can also access the volume mixer by right-clicking the
speaker icon in the lower right of the screen, and choosing
“Open Volume Mixer.”
If the Mute setting is checked, clear the check mark.
Macintosh users
Windows Vista users
1. In “System Preferences,” click [Sound].
2. Click the [Output] tab.
1. Open the “Control Panel,” and click [Hardware and
Sound].
If you’re using the Classic View, click Control Panel Home to
exit the Classic View.
3. In the Choose a device for sound output field, make
sure that the [SD-50] is selected, and use the
Output volume slider to adjust the volume.
If Mute is checked, clear the check mark.
2. In “Sound,” click [Adjust system volume].
3. The Volume Mixer will appear. From the “Device”
menu, select the SD-50’s [OUT] and adjust the
volume.
4. Adjust the Device or Application volume.
If the Mute button is on, click the mute button once again to
turn it off.
You can also access the volume mixer by right-clicking the
speaker icon located in the bottom right corner of your
screen, and choosing Open “Volume Mixer.”
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Voice communication Software
Settings (Windows 7)
Windows Monitoring Function Settings
(Windows 7)
If you’re using voice communication software, the volume of
the audio device might be adjusted automatically according
to the status of your conversation.
If the monitoring function of Windows is enabled, the input
sound might be heard in duplicate (doubled) or might cause
an oscillating loop (feedback).
In this case, proceed as follows to disable automatic volume
adjustment.
In this case, proceed as follows to disable the monitoring
function in Windows.
1. Open the “Control Panel,” click “Hardware and
Sound,” and then click “Sound.”
1. Open the “Control Panel,” click [Hardware and
Sound], and then click [Sound].
*
If the “Control Panel” shows the Icon view, click [Sound].
*
If the Control Panel shows the Icon view, click “Sound.”
2. In the [Communications] tab, change the setting
“When Windows detects communications activity”
to [Do nothing].
2. In “Recording,” select the SD-50 [IN], and click
[Properties].
3. Open the “Listen” tab, and clear the [Listen to this
device] check box.
3. Click [OK] to close “Sound.”
4. Click [OK] to close “Properties.”
5. Click [OK] to close “Sound.”
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
If an incorrect operation is performed, or if processing could not be performed as you specified, an error message will
appear.
Refer to the explanation for the error message that appears, and take the appropriate action.
Message
Meaning
Action
USB Mem Not
Ready!
USB memory is not connected.
Connect USB memory.
Failed to load data from USB memory.
It may be that the file is damaged.
Make sure that USB memory is correctly connected.
Do not use this file.
This file cannot be loaded since its format
is incorrect.
Read Error!
Do not use this file.
The target file was not found in USB
memory.
Make sure that the target file exists in USB memory.
Make sure that USB memory is correctly connected.
Failed to write data to USB memory.
Delete unneeded files from the USB memory.
Alternatively, use a different USB memory device, one
that has more free space available.
Data cannot be written because the USB
memory has no more free space.
Write Error!
The file or the USB memory itself is write
protected.
Make sure that the file or the USB memory is not write
protected.
This is a file that the SD-50 is unable to
play.
Do not use this file.
This song has not been transferred from
Playlist Editor to USB memory.
Select the song for transfer from Playlist Editor, and
transfer the data once again to USB memory.
Incorrect File!
Playback is not possible, since you have
exceeded the number of songs that the
SD-50 can handle.
The SD-50 can handle up to 99 songs in the root
directory, and a total of up to 399 songs in all other
playlists.
Please execute a Factory Reset.
If this does not resolve the problem, contact your
dealer or a nearby Roland service center.
It is possible that the contents of system
memory have been damaged.
Sys Mem Damaged!
MIDI Buffer Full!
MIDI Offline!
An unusually large amount of MIDI data
was received, and could not be processed.
Reduce the amount of MIDI messages that are being
transmitted.
Check that there is no problem with the MIDI cable
connected to the SD-50’s MIDI IN, and that the MIDI
cable was not disconnected.
The MIDI IN connection was broken.
Now Playing!
Battery Low!
The Song Player is currently playing.
The battery has run down.
Either stop playback, or wait until playback has ended.
Recharge the batteries, or use an AC adaptor.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings Saved as User Data
The following settings are saved when you back up user data (p. 75).
System settings (p. 75)
Setting
LCD Contrast
Master Tune
Output Gain
Battery
Mastering
PowerSave
Power Off
Input/output volume settings (p. 71)
Setting
Mic/Line Input
MP3/Audio Player
SMF Player
Audio settings (p. 59)
Setting
Mic Input SW
Mic Echo Level
Audio Input Att
Direct Mon Sw
Direct Mon Level
TG to COMPUTER
Studio set (p. 54)
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Solo Tone
Solo Tone
The Solo sounds and how to play them
The Solo sounds allow you to reproduce the natural tonal changes (changes in dynamics) that are distinctive of each instrument as
you range from delicate soft notes to strongly played powerful notes—not merely changes in the volume.
*
*
Dynamics can be controlled by Note-on Velocity, Modulation controller (CC01), and Expression (CC11).
Since the Modulation controller is assigned to dynamics, Vibrato has been assigned to be controlled by channel pressure
messages.
After pressing a key, you can operate the Modulation controller (CC01) or Expression pedal (CC11) to continuously control the dynamics.
By playing legato (i.e., by pressing the next note before you release the previous note) you can create smooth transitions between notes.
*
In order to obtain the legato effect, set the Mono/Poly mode (CC126=Mono/CC127=Poly) to Mono. With the Solo sounds, set to
Mono upon power-up.
Normally, even an instrument that is set to play in Mono mode will allow you to sound a chord by pressing two or more notes
simultaneously. When all notes turn off, the instrument will return to Mono mode.
*
This effect will be obtained if the Mono/Poly mode is set to Mono.
Wind instruments (Shakuhachi, Trombone) allow you to control Growl Sens (CC18). This lets you vary the distinctive nuance (growl)
that occurs when you blow strongly into a wind instrument.
You can use CC16 to vary the Noise Level. This controls the breath noise of a wind instrument, or the bowing noise or picking noise of
a string instrument.
You can use CC17 to vary the Play Stability (accuracy of the performance). If this value is 0, the pitch during the attack of the sound
will be unstable. Higher values allow you to play more precise pitches.
Variations for the Solo sounds
Each instrument provides effective performance variation sounds, and you can use control changes (CC80/CC81) to instantly switch
between these while you play.
Variation
No.
ToneName
CC80
CC81
Pizzicato
Fall
001
002
003
Violin
Staccato
Staccato
Staccato
Trombone
Shakuhachi
-
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Solo Tone
Features of the Solo sounds
Sound
Features
•
If you play two or more notes simultaneously, a chord will sound, simulating the double-stop playing technique of a violin.
When all notes turn off, the instrument will return to mono mode.
Violin
*
Vibrato will not automatically be applied below the lowest note that a violin can sound (note number 55). This simulates the
resonance of the open strings.
•
•
•
Playing legato with the portamento switch ON will produce the glissando effect that is typical of a trombone.
Moving the bender up will produce the discontinuous pitch change that is distinctive of brass instruments. (*1)
Moving the bender down will produce a “fall” effect. (*1)
Trombone
•
•
•
The distinctive breath noise of the shakuhachi is simulated.
Play strongly (note-on velocity 115) to produce the effect of allowing a large amount of breath to be heard in the sound.
When you play legato, notes will be connected as if they were played with a single breath. While playing legato, play strongly
(note-on velocity 115) to simulate a grace note characteristic of a shakuhachi.
Shakuhachi
*1: This effect will be obtained if control change (CC82) is ON. If this is OFF, the normal pitch bend effect will occur.
(CC82: 0–63 = OFF, 64–127 = ON)
107
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDI Implementation Chart
Date : Jan. 5, 2010
Version : 1.00
Model SD-50
Function...
MIDI Implementation Chart
Transmitted
Recognized
Remarks
Basic
Channel
Default
Changed
X
X
1-16
1-16
Default
Messages
Altered
X
Mode 3
Mode 3, 4 (M=1)
Mode
X
*1
**************
Note
Number
X
0-127
0-127
True Voice
**************
Velocity
Note ON
Note OFF
X
X
O
O
Aftertouch Key’s
Channel’s
X
X
O
O
Pitch Bend
X
O
Control
Change
0,32
1
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
Bank select
Modulation
O
5
O
Portamento time
Data entry
6,38
7
O
O
Volume
10
O
Panpot
11
O
Expression
16
O (Tone Modify 1)
General purpose controller 1
General purpose controller 2
General purpose controller 3
General purpose controller 4
Hold1
17
O (Tone Modify 2)
18
O (Tone Modify 3)
19
O (Tone Modify 4)
64
O
65
O
Portamento
66
O
Sostenuto
67
O
Soft
68
O
Legato foot switch
Resonance
71
O
72
O
Release time
73
O
Attack time
74
O
Cutoff
75
O
Decay time
76
O
Vibrato rate
77
O
Vibrato depth
78
O
Vibrato delay
80
O (Tone Modify 5)
General purpose controller 5
General purpose controller 6
General purpose controller 7
General purpose controller 8
Portamento control
General purpose effects 1
General purpose effects 3
Increment, Decrement
NRPN LSB,MSB
81
O (Tone Modify 6)
82
O (Tone Modify 7)
83
X
O
84
91
O (Reverb)
93
O (Chorus)
96,97
98,99
100,101
102–119
X
X
O
X
RPN LSB,MSB
Program
Change :
O
O
0-127
True Number
**************
Program Number 1-128
System Exclusive
O
O
: Song Postion
X
X
X
X
X
X
System
Common
: Song Select
: Tune
System
Realtime
: Clock
: Command
X
X
O
X
: All Sound Off
X
X
X
X
X
X
O
: Reset All Controllers
: Local ON/OFF
O
Aux
X
Messages : All Note Off
: Active Sensing
O (123-127)
O
X
: System Reset
Notes
*1 Recognized as M=1 even if M1.
Mode 1: OMNI ON, POLY
Mode 3: OMNI OFF, POLY
Mode 2: OMNI ON, MONO
Mode 4: OMNI OFF, MONO
O: Yes
X: No
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Sampling Frequency
USB Audio: 44.1 kHz
SD-50:
128 Voices Sound Module with Audio Interface
AD/DA Conversion: 44.1 kHz
Sound Generator Section
Nominal Input Level
Input jack (MIC/GUITAR IN)
Mic: -50– -30 dBu
Parts
16 parts
Guitar: -30– -10 dBu
Input jack (LINE IN)
Maximum Polyphony
128 voices
Line: -30– +4 dBu
Wave Memory
Nominal Output Level
128 M bytes (16-bit linear equivalent)
Output jacks: 0 dBu
Internal Sounds
Preset Sounds: 1,125 Tones
Rhythm Sets: 32
SMF/Audio Player Section
File Format
Standard MIDI File: format-0/1
*
3 Solo tones and GM2/GS compatible sounds are included.
Audio File: WAV, AIFF, MP3
User Memory
Others
Studio Sets: 3
Display
Effects
Reverb
122 x 32 dots LCD display
Chorus
Jacks and Connectors
MIDI connectors (OUT, IN)
Mastering
LINE IN jack (Stereo Mini)
Audio Interface Section
LINE OUT jacks (Stereo RCA-PIN)
PHONES jack (Stereo Mini)
Number of Audio Input/Output Channels
Input: 1 pair of stereo (MIC, GUITAR: Monaural/LINE: Stereo)
Output: 1 pair of stereo
MIC IN jack (XLR type, phantom power available)
MIC/GUITAR IN connector (1/4 inch phone type, Hi-Z
available)
USB Connectors
Signal Processing
USB Audio: 16 bits / 24 bits
AD/DA Conversion: 24 bits
•
COMPUTER (supports USB 2.0 Full-Speed USB MIDI and
USB Audio)
•
MEMORY (supports USB 2.0 Hi-Speed Flash Memory)
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Power Supply
DC 9 V (AC Adaptor)
Battery (AA x 6, ALKALIN or Ni-MH)
USB Bus power available
Expected battery life under continuous use
Nickel-metal hydride: 4 hours
Alkaline: 3 hours
*
These figures will vary depending on the actual conditions of
use.
Current Draw
500 mA (Bus power)
400 mA (AC Adaptor, Battery)
Dimensions
249.9 (W) x 166.9 (D) x 55.15 (H) mm
9-7/8(W) x 6-5/8 (D) x 2-3/16 (H) inches
Weight
0.8 kg / 1 lbs 13 oz (excluding batteries)
Accessories
Owner’s Manual
USB Cable
DVD-ROM (USB Driver, SONAR LE)
AC Adaptor
Power Cord
Options
USB Memory
(0 dBu = 0.775 V rms)
*
In the interest of product improvement, the specifications,
appearance and /or contents of this unit or this package are
subject to change without prior notice.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
A
D
Driver .......................................................................................... 23
Drum Set .................................................................................... 45
B
Backup ....................................................................................... 91
BUS ............................................................................................. 16
C
Chorus Send ............................................................................... 51
CHORUS1 ................................................................................... 52
CHORUS2 ................................................................................... 52
CHORUS3 ................................................................................... 52
CHORUS4 ................................................................................... 52
COMPUTER Connector ............................................................... 16
COMPUTER Indicator ................................................................. 14
FB CHORUS ................................................................................. 52
FLANGER .................................................................................... 52
G
Ground Terminal ........................................................................ 17
I
K
[KEY CTRL] Button ...................................................................... 15
L
LARGE HALL ............................................................................... 52
LARGE ROOM ............................................................................. 52
LINE IN Jack ................................................................................ 17
LINE OUT Jacks ........................................................................... 17
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
M
MIDI ............................................................................................ 89
Minus One .................................................................................. 73
[MINUS ONE] (CENTER CANCEL) Button ..................................... 15
N
[TEMPO] Button .......................................................................... 15
P
Pan ............................................................................................. 51
Part ............................................................................................. 45
Play ............................................................................................ 91
PLAY/PAUSE Button ................................................................... 15
[PLAYER] Button ......................................................................... 15
Playlist ........................................................................................ 91
Polyphony .................................................................................. 45
[POWER] Switch ......................................................................... 16
PREV Button ............................................................................... 15
Program Change ........................................................................ 48
USB Memory ............................................................................... 91
USB MEMORY Connector ........................................................... 18
V
[VALUE] Dial ............................................................................... 15
[V-LINK] Button ........................................................................... 14
[VOLUME] Dial ............................................................................ 18
112
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
113
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
114
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
115
Download from Www.Somanuals.com. All Manuals Search And Download.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
SD-50
Sound Module with Audio Interface
Cakewalk, Inc.
268 Summer Street Boston, MA 02210
Telephone : (617) 423-9004
fig.15_WEEE_Small.eps
For EU Countries
116
Download from Www.Somanuals.com. All Manuals Search And Download.
fig.16_ChineseRoHS.eps
For China
fig.17_Proposition65.eps
(
)
For C.A. US Proposition 65
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
fig.05.eps
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
fig.09B-17.eps
For EU Countries
This product complies with the requirements of EMC Directive 2004/108/EC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
(
)
For C.A. US Proposition 65
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
*
5
1
0
0
0
1
1
3
4
6
-
0
1
*
Download from Www.Somanuals.com. All Manuals Search And Download.
|
