Download from Www.Somanuals.com. All Manuals Search And Download.
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS” Owner’s manual p. 3),
“USING THE UNIT SAFELY” (Owner’s manual p. 8), and “IMPORTANT NOTES” (Owner’s manual p. 10). These sections
provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you
have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety. The
manual should be saved and kept on hand as a convenient reference.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
product’s enclosure that may be of sufficient magnitude to
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
The exclamation point within an equilateral triangle is
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
7. Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE: NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
Copyright © 2010 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Roland is a registered trademark or trademark of Roland Corporation in the United States and/or other countries.
Download from Www.Somanuals.com. All Manuals Search And Download.
Lessons at home!
Play together with your family
Dividing the keyboard for two-person
performance (Twin Piano) • • • p. 27
Check your own performance
Recording your performance • • • p. 41
Play along with a metronome
Performing with the metronome • • • p. 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Select and listen to the song you want to play!
Listening to songs • • • p. 37
Playing back songs on external media • • • p. 62
Play along with the song one hand at a time
Playing parts individually • • • p. 38
Now I can pllay it!
Night-time or early morning lessons
Using the Headphones • • • p. 18
Play using different sounds
Performing with various sounds • • • p. 21
Slow down the tempo for difficult passages
Changing the song’s tempo • • • p. 40
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Songs ............................. 37
Adjusting the Sound’s Volume.................................... 17
About the Adjuster ................................................... 20
Erasing Your Recorded Performance.........................43
Saving Your Recorded Performance..........................44
Deleting a Saved Song....................................................46
Recording Each Hand Separately.........................48
Recording a Performance You Play Along
with a Song ..................................................................51
Changing the Metronome’s Tempo ................... 22
Adjusting the Metronome’s Volume.................. 23
Performance (Count-in) .......................................... 24
Adjusting the Depth of the Reverb Effect ........ 25
Heard (Twin Piano Mode)....................................... 28
Playing Different Tones in the Left and Right
Sides of the Keyboard (Split Play)............................... 29
Changing the Tones of the Left and Right
Zones ............................................................................. 30
Changing the Keyboard’s Split Point ................. 31
Transposing the Keyboard (Transpose) ................... 32
Disabling the Buttons (Panel Lock)............................ 33
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation in Function Mode ............................ 53
Adjusting the Sound’s Brilliance (Brilliance).... 55
(Master Tuning).......................................................... 55
Adjusting the Dual Play Volume Balance
Connecting a Media.........................................................60
Installing the Floppy Disk Drive............................60
Initializing the Memory (Format Media)............61
(Ext. Memory Mode)..................................................61
Adjusting the Volume of an Audio File
Adjusting the Volume (Master Gain).................. 56
Changing the Parts Assigned to the Track
Changing the Tempo of an Audio File
(Center Cancel) ...........................................................63
(Recommended Tone) .............................................63
Metronome Setting......................................................... 57
Playing Back at a Fixed Tempo
Performing Settings ........................................................ 57
Copying the Song......................................................65
Having Audio from an External Device be
Connecting Speakers to the LX-10F and
Connecting to MIDI Devices .........................................67
Affect (Transpose Mode)......................................... 57
Changing the Pitch of the Tone in Octave
Pedal Settings.................................................................... 58
(Damper Pedal Part) ................................................. 58
Switching On/Off the Display of Lyrics (Lyrics)...... 58
Setting the Type of CD To be Played Back
(CD/Audio Type) ............................................................... 58
Changing the Language Displayed in the Screen
(Language).......................................................................... 58
Storing Your Settings
Module by Playing the LX-10F ..............................67
(MIDI Transmit Ch.)...................................................68
(Memory Backup) ............................................................. 59
Restoring the Factory Settings (Factory Reset) ..... 59
a MIDI Device (Composer MIDI Out)...................68
Troubleshooting ...............................................................71
Error Messages...................................................................74
Tone List...............................................................................75
Internal Song List..............................................................78
Parameters Stored in Memory Backup .....................79
Music Files That the LX-10F Can Use .........................80
Main Specifications..........................................................81
Index......................................................................................83
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
About WARNING and CAUTION Notices
About the Symbols
The symbol alerts the user to important instructions or
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
The symbol alerts the user to items that must never be
carried out (are forbidden).The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
The symbol alerts the user to things that must be
carried out.The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
ALWAYS OBSERVE THE FOLLOWING
•
Do not open or perform any internal modifications on
the unit.
•
Do not excessively twist or bend the power cord, nor
place heavy objects on it. Doing so can damage the
cord, producing severed elements and short circuits.
Damaged cords are fire and shock hazards!
...................................................................................................................................................
..................................................................................................................................................
•
Do not attempt to repair the unit, or replace parts
within it (except when this manual provides specific
instructions directing you to do so). Refer all servicing
to your retailer, the nearest Roland Service Center, or
an authorized Roland distributor, as listed on the
“Information” page.
•
This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could cause
permanent hearing loss. Do not operate for a long
period of time at a high volume level, or at a level that
is uncomfortable. If you experience any hearing loss
or ringing in the ears, you should immediately stop
using the unit, and consult an audiologist.
...................................................................................................................................................
•
Never install the unit in any of the following locations.
..................................................................................................................................................
•
Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or are
Damp (e.g., baths, washrooms, on wet floors); or are
Exposed to steam or smoke; or are
Subject to salt exposure; or are
Humid; or are
Exposed to rain; or are
Dusty or sandy; or are
Subject to high levels of vibration and shakiness.
•
Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft drinks,
etc.) to penetrate the unit.
•
•
•
•
•
•
•
..................................................................................................................................................
...................................................................................................................................................
•
Immediately turn the power off, remove the power
cord from the outlet, and request servicing by your
retailer, the nearest Roland Service Center, or an
authorized Roland distributor, as listed on the
“Information” page when:
•
Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
...................................................................................................................................................
•
The power-supply cord or the plug has been
damaged; or
•
The unit should be connected to a power supply only
of the type described in the operating instructions, or
as marked on the rear panel of unit.
•
•
If smoke or unusual odor occurs
Objects have fallen into, or liquid has been spilled
onto the unit; or
...................................................................................................................................................
•
•
The unit has been exposed to rain (or otherwise has
become wet); or
The unit does not appear to operate normally or
exhibits a marked change in performance.
•
Use only the attached power-supply cord. Also, the
supplied power cord must not be used with any other
device.
..................................................................................................................................................
...................................................................................................................................................
8
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
•
In households with small children, an adult should
provide supervision until the child is capable of
following all the rules essential for the safe operation
of the unit.
•
Never climb on top of, nor place heavy objects on the
unit.
...................................................................................................................................................
..................................................................................................................................................
•
Protect the unit from strong impact.
(Do not drop it!)
•
Never handle the power cord or its plugs with wet
hands when plugging into, or unplugging from, an
outlet or this unit.
...................................................................................................................................................
..................................................................................................................................................
•
Do not force the unit’s power-supply cord to share an
outlet with an unreasonable number of other devices.
Be especially careful when using extension cords—
the total power used by all devices you have
connected to the extension cord’s outlet must never
exceed the power rating (watts/amperes) for the
extension cord. Excessive loads can cause the
insulation on the cord to heat up and eventually melt
through.
•
If you need to move the instrument, take note of the
precautions listed below. At least two persons are
required to safely lift and move the unit. It should be
handled carefully, all the while keeping it level. Make
sure to have a firm grip, to protect yourself from injury
and the instrument from damage.
•
Check to make sure the screws securing the unit to the
stand have not become loose. Fasten them again
securely whenever you notice any loosening.
Disconnect the power cord.
...................................................................................................................................................
•
•
•
•
Disconnect all cords coming from external devices.
Raise the adjusters on the stand (p. 20).
Close the lid.
•
Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on the
“Information” page.
..................................................................................................................................................
•
Before cleaning the unit, turn off the power and
unplug the power cord from the outlet (p. 16).
...................................................................................................................................................
•
DO NOT play a CD-ROM disc on a conventional audio
CD player. The resulting sound may be of a level that
could cause permanent hearing loss. Damage to
speakers or other system components may result.
..................................................................................................................................................
•
Whenever you suspect the possibility of lightning in
your area, pull the plug on the power cord out of the
outlet.
...................................................................................................................................................
•
Do not put anything that contains water (e.g., flower
vases) on this unit. Also, avoid the use of insecticides,
perfumes, alcohol, nail polish, spray cans, etc., near
the unit. Swiftly wipe away any liquid that spills on
the unit using a dry, soft cloth.
..................................................................................................................................................
•
Be careful when opening/closing the lid so you do
not get your fingers pinched (p. 14). Adult
supervision is recommended whenever small
children use the unit.
..................................................................................................................................................
•
The unit should be located so that its location or
position does not interfere with its proper
ventilation.
•
When using the stool, please observe the following
points:
•
•
•
•
Do not use the stool as a toy, or as a stepping stool.
Do not allow two or more persons to sit on the stool.
Do not adjust the height while sitting on the stool.
Do not sit on the stool if the bolts holding the stool
legs are loose. (If the bolts are loose, immediately re-
tighten them using the supplied tool.)
...................................................................................................................................................
•
Always grasp only the plug on the power-supply cord
when plugging into, or unplugging from, an outlet or
this unit.
•
Never insert your hand into the gap (the metal height
adjustment mechanism) under the seat lid. Doing so
may cause your hand to be pinched or injured.
...................................................................................................................................................
•
At regular intervals, you should unplug the power
plug and clean it by using a dry cloth to wipe all dust
and other accumulations away from its prongs. Also,
disconnect the power plug from the power outlet
whenever the unit is to remain unused for an
extended period of time. Any accumulation of dust
between the power plug and the power outlet can
result in poor insulation and lead to fire.
..................................................................................................................................................
•
Always keep the following small parts that may be
removed out of the reach of small children to avoid
accidental ingestion of these parts.
•
•
•
Screws for assembling the stand you may remove
Included wing nut for headphone hook
Included stereo 1/4” plug adaptor
(if a stereo 1/4”plug adaptor is included with your
headphones)
...................................................................................................................................................
•
Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..................................................................................................................................................
...................................................................................................................................................
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
Power Supply
•
•
The pedals of this unit are made of brass.
Brass eventually darkens as the result of the natural oxidization
process. If the brass becomes tarnished, polish it using commercially
available metal polisher.
•
Do not connect this unit to same electrical outlet that is being used
by an electrical appliance that is controlled by an inverter (such as a
refrigerator, washing machine, microwave oven, or air conditioner),
or that contains a motor. Depending on the way in which the
electrical appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not practical to
use a separate electrical outlet, connect a power supply noise filter
between this unit and the electrical outlet.
Since wood will expand and contract depending on how it is used
and the environment in which it is located, products made of wood
may experience a gradual loosening of the screws over time.
To ensure that your piano remains in safe, optimal condition, you
should regularly check the tightness of the screws in the locations
shown in the illustration. If you find that any screws are loose, use a
screwdriver to tighten them.
•
•
Before connecting this unit to other devices, turn off the power to all
units. This will help prevent malfunctions and/or damage to speakers
or other devices.
Although the LCD and LEDs are switched off when the POWER switch
is switched off, this does not mean that the unit has been completely
disconnected from the source of power. If you need to turn off the
power completely, first turn off the POWER switch, then unplug the
power cord from the power outlet. For this reason, the outlet into
which you choose to connect the power cord’s plug should be one
that is within easy reach and readily accessible.
Placement
•
Using the unit near power amplifiers (or other equipment containing
large power transformers) may induce hum. To alleviate the
problem, change the orientation of this unit; or move it farther away
from the source of interference.
•
•
This device may interfere with radio and television reception. Do not
use this device in the vicinity of such receivers.
Maintenance (Polished-finish pianos)
Noise may be produced if wireless communications devices, such as
cell phones, are operated in the vicinity of this unit. Such noise could
occur when receiving or initiating a call, or while conversing. Should
you experience such problems, you should relocate such wireless
devices so they are at a greater distance from this unit, or switch
them off.
•
Since your piano has a polished finish that is as delicate as that found
on finely crafted wooden furniture, it needs careful, periodic care.
•
•
For regular dusting, use a soft, clean cloth and/or a piano-use
feather duster. Be sure to wipe gently. Even tiny granules of grit
can damage the surface of the unit if you use too much pressure
when wiping.
If the cabinet gets dirty, wipe it with a soft cloth that has been
soaked with water, then squeezed dry. Afterwards, wipe it again
with a soft dry cloth. Do not use any cleaners or detergents, since
they might deteriorate the surface of the cabinet, and produce
cracks. Do not use dusting cloths that contain chemicals.
If the cabinet’s surface loses its luster, wipe it thoroughly with a
soft cloth dampened with a little of the piano polishing liquid.
•
Do not expose the unit to direct sunlight, place it near devices that
radiate heat, leave it inside an enclosed vehicle, or otherwise subject
it to temperature extremes. Also, do not allow lighting devices that
normally are used while their light source is very close to the unit
(such as a piano light), or powerful spotlights to shine upon the same
area of the unit for extended periods of time. Excessive heat can
deform or discolor the unit.
•
•
About piano polishing liquid
•
•
When moved from one location to another where the temperature
and/or humidity is very different, water droplets (condensation) may
form inside the unit. Damage or malfunction may result if you
attempt to use the unit in this condition. Therefore, before using the
unit, you must allow it to stand for several hours, until the
condensation has completely evaporated.
•
Use polishing liquid as directed by the instructions for the
product.
•
Use only polishing liquid that is intended for use on polished-
finish pianos. Using any other polishing liquid may cause
scratches, deformation, or discoloration. To purchase polishing
liquid, contact your nearby musical instrument dealer.
Use the polishing liquid only on the polished surfaces of the
cabinet. Always wipe the surface with the grain using straight,
even strokes. Do not repeatedly wipe the same places using too
much pressure, since that might result in the loss of luster.
Be sure to keep the polishing liquid out of the reach of small
children. If the polishing liquid is accidentally swallowed, first get
them to vomit, then take them to a doctor.
Do not allow rubber, vinyl, or similar materials to remain on the unit
for long periods of time. Such objects can discolor or otherwise
harmfully affect the finish.
•
•
•
•
Do not allow objects to remain on top of the keyboard. This can be
the cause of malfunction, such as keys ceasing to produce sound.
Do not paste stickers, decals, or the like to this instrument. Peeling
such matter off the instrument may damage the exterior finish.
Repairs and Data
Maintenance
•
Please be aware that all data contained in the unit’s memory may be
lost when the unit is sent for repairs. Important data should always
be backed up on a USB memory, or written down on paper (when
possible). During repairs, due care is taken to avoid the loss of data.
However, in certain cases (such as when circuitry related to memory
itself is out of order), we regret that it may not be possible to restore
the data, and Roland assumes no liability concerning such loss of
data.
•
•
To clean the unit, use a dry, soft cloth; or one that is slightly
dampened. Try to wipe the entire surface using an equal amount of
strength, moving the cloth along with the grain of the wood.
Rubbing too hard in the same area can damage the finish.
Never use benzine, thinners, alcohol or solvents of any kind, to avoid
the possibility of discoloration and/or deformation.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
Additional Precautions
•
Floppy disks have a “write protect” tab which can protect the disk
from accidental erasure. It is recommended that the tab be kept in
the PROTECT position, and moved to the WRITE position only when
you wish to write new data onto the disk.
•
Please be aware that the contents of memory can be irretrievably lost
as a result of a malfunction, or the improper operation of the unit. To
protect yourself against the risk of loosing important data, we
recommend that you periodically save a backup copy of important
data you have stored in the unit’s memory on a USB memory.
Rear side of the disk
•
•
Unfortunately, it may be impossible to restore the contents of data
that was stored on a unit’s memory or a USB memory once it has
been lost. Roland Corporation assumes no liability concerning such
loss of data.
Write
(can write new data onto disk)
Use a reasonable amount of care when using the unit’s buttons,
sliders, or other controls; and when using its jacks and connectors.
Rough handling can lead to malfunctions.
Write Protect Tab
Protect
(prevents writing to disk)
•
•
The identification label should be firmly affixed to the disk. Should
the label come loose while the disk is in the drive, it may be difficult
to remove the disk.
•
•
Never strike or apply strong pressure to the display.
When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing
shorts, or damage to the cable’s internal elements.
Store all disks in a safe place to avoid damaging them, and to protect
them from dust, dirt, and other hazards. By using a dirty or dust-
ridden disk, you risk damaging the disk, as well as causing the disk
drive to malfunction.
•
•
A small amount of heat will radiate from the unit during normal
operation.
To avoid disturbing your neighbors, try to keep the unit’s volume at
reasonable levels. You may prefer to use headphones, so you do not
need to be concerned about those around you (especially when it is
late at night).
Handling USB memory
(Using Optional USB Memory)
•
Do not connect or disconnect USB memory while it is being read
from, or written to (i.e., while the USB memory access indicator will
blink).
•
When you need to transport the unit, pack it in shock-absorbent
material. Transporting the unit without doing so can cause it to
become scratched or damaged, and could lead to malfunction.
•
•
•
Carefully insert the USB memory all the way in—until it is firmly in
place.
•
•
Do not apply undue force to the music rest while it is in use.
Never touch the External Memory connector. Also, avoid getting the
terminals dirty.
Some connection cables contain resistors. Do not use cables that
incorporate resistors for connecting to this unit. The use of such
cables can cause the sound level to be extremely low, or impossible
to hear. For information on cable specifications, contact the
manufacturer of the cable.
USB memories are constructed using precision components; handle
the USB memories carefully, paying particular note to the following.
•
To prevent damage to the USB memories from static electricity, be
sure to discharge any static electricity from your own body before
handling the USB memories.
•
Before opening or closing the keyboard lid, always make sure that no
pets or other small animals are located on top of the instrument (in
particular, they should be kept away from the keyboard and its lid).
Otherwise, due to the structural design of this instrument, small pets
or other animals could end up getting trapped inside it. If such a
situation is encountered, you must immediately switch off the power
and disconnect the power cord from the outlet. You should then
consult with the retailer from whom the instrument was purchased,
or contact the nearest Roland Service Center.
•
•
•
Do not touch or allow metal to come into contact with the contact
portion of the USB memories.
Do not bend, drop, or subject USB memories to strong shock or
vibration.
Do not keep USB memories in direct sunlight, in closed vehicles,
or other such locations.
•
•
Do not allow USB memories to become wet.
Do not disassemble or modify the USB memories.
Handling the Floppy Disk Drive
(Using Optional Floppy Disk Drive)
Handling CD-ROMs
(Using Optional CD-Drive)
•
Never attempt to remove a floppy disk from the drive while the drive
is operating (the indicator is lit); damage could result to both the disk
and the drive.
•
Avoid touching or scratching the shiny underside (encoded surface)
of the disc. Damaged or dirty CD-ROM discs may not be read
properly. Keep your discs clean using a commercially available CD
cleaner.
Handling Floppy Disks
•
Floppy disks contain a plastic disk with a thin coating of magnetic
storage medium. Microscopic precision is required to enable storage
of large amounts of data on such a small surface area. To preserve
their integrity, please observe the following when handling floppy
disks:
*
*
GS (
) is a registered trademark of Roland Corporation.
) is a registered trademark of Yamaha
XGLite (
Corporation.
•
•
•
Never touch the magnetic medium inside the disk.
Do not use or store floppy disks in dirty or dusty areas.
Do not subject floppy disks to temperature extremes (e.g., direct
sunlight in an enclosed vehicle). Recommended temperature
range: 10 to 50 degree C (50 to 122 degree F)
*
*
MMP (Moore Microprocessor Portfolio) refers to a patent
portfolio concerned with microprocessor architecture, which
was developed by Technology Properties Limited (TPL).
Roland has licensed this technology from the TPL Group.
•
Do not expose floppy disks to strong magnetic fields, such as
those generated by loudspeakers.
All product names mentioned in this document are
trademarks or registered trademarks of their respective
owners.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
1
2
3
4
5
6
7
17
26
21
22
23
24
25
1
2
7
[Volume] slider
[Piano Designer] button
Allows you to adjust the piano sound to your taste,
for example by adjusting the string resonance
(p. 34).
[Reverb] button
Adds reverberation similar to what you would hear
8
9
when performing in a concert hall (p. 25).
Display
This shows the sound name, song number, tempo
3
4
[Transpose] button
and time signature.
Transposes the keyboard and/or song.
• Transposing the song playback (p. 40).
[▲] [▼] buttons
Use these buttons to select items in the Piano
Designer or in Function mode.
[Twin Piano] button
10
[–] (
) [+] (
) buttons
• Divides the keyboard into two separate sections,
allowing two people to perform in the same
registers (p. 27).
• Change the value of settings such as sounds or
functions.
• Allows you to perform with a split keyboard
(p. 29).
• Select the sound to be played from the keyboard
(p. 21).
• Select a song (p. 37).
5
6
[Function] button
• Fast-forward/rewind a song (p. 37).
Takes you to Function mode, where you can make a
variety of settings, including those that change the
sound or various other functions (p. 53).
11
[Song] (Tempo) button
• Indicates the name of the currently selected song
(p. 37).
Tone buttons
Here you can select the sound you’ll hear when you
• Changes the metronome’s tempo or time signature
(p. 22).
play the keyboard (p. 21).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
8
9
10
11
12
13
14
15
16
18
19
20
12
13
19
[Metronome] button
Pedal connector
Turns the internal metronome on/off (p. 22).
Connect the pedal cord of the dedicated stand to
this connector (p. 14).
[
20
21
22
AC In (AC Inlet)
• Stops/starts playback of an internal song or a
recorded performance (p. 37).
Connect the included power cord here (p. 14).
• Starts/stops recording of your performance (p. 41).
Phones jacks
14
15
[
] (Rec) button
Here you can connect headphones (p. 18).
This lets you record your own performance into the
LX-10F (p. 41).
Input jacks (L/Mono, R)
electronic musical instrument, and listen to the
connected device through the LX-10F’s speakers
(p. 66).
Track buttons
• Allows you to play back your performance
separately for each hand (p. 38).
• Records your performance separately for each
hand (p. 48).
23
24
25
MIDI Out/In connectors
You can connect these to external MIDI devices to
transfer performance data (p. 67).
• Holding down the [Right] button will disable all
button operations (Panel Lock) (p. 33).
16
17
18
[Display Contrast] knob
This adjusts the brightness of the screen (p. 17).
You can connect this to your computer for
transferring performance data (p. 69).
[Power] switch
External Memory connector
Turns the power on/off (p. 16).
Here you can connect USB memory, a CD drive, or a
floppy disk drive, and use it to play or save songs
(p. 60).
Output jacks (L/Mono, R)
You can connect an audio device or external
powered speakers here to reproduce the LX-10F’s
sound (p. 66).
26
Pedals
•
•
These are used mainly when playing piano (p. 20).
You can assign a variety of functions to the pedals
(p. 58).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Play
Getting Ready to Play
Connecting the Power Cord
Before connecting cables to the bottom panel (the back
edge of the LX-10F’s bottom), you’ll need to remove the rear
board upper.
Check before you connect the power cord.
To remove the rear board upper, remove the three screws
from the locations shown in the illustration.
•
•
Make sure that the [Power] switch is off (p. 16).
Make sure that the [Volume] slider is minimized (p. 17).
1. Connect the included power cord to the AC Inlet
located at the rear of the bottom panel.
Rear Board Upper
2. Plug the other end of the power cord into an AC
outlet.
fig.PowerCord.eps
Connecting the Speaker Cable
Plug the speaker cable extending from the stand into the
speaker connector located at the rear of the LX-10F’s bottom
panel.
AC outlet
Pay attention to the shape of the speaker cable’s connector,
1
and insert it until you hear it click securely into place.
fig.SpeakerCable.eps
2
You must use the power cord included with the LX-10F.
Opening/Closing the Lid
To open the lid, use both hands to lift it lightly.
The lid of the LX-10F is designed to close softly even if
you remove your hands from it. However, it will close
quite abruptly if it has been opened only slightly. Be
careful not to pinch your fingers in the gap.
Connecting the Pedal Cord
Plug the pedal cord extending from the stand into the Pedal
connector located at the rear of the LX-10F’s bottom panel.
fig.PedalCord.eps
1. To open the lid, use both hands to lift it.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Play
2. To close the lid, use both hands to gently lower it.
Using the Music Rest
You can place music books or sheet music on the top edge
of the opened lid.
If you need to move the piano, make sure the lid is closed
first to prevent accidents.
Opening/Closing the Top Lid
The top lid must be opened or closed by an adult.
Do not force the top lid backward; doing so will damage
it.
Tips for Placing Music
Be careful not to pinch your fingers in the gap.
•
•
•
Insert the sheet music into the groove on the top
edge of the lid.
Opening the Top Lid
Crease sheet music so that it will stay open.
If this does not work, use paper clips to secure it.
1. Lift up the top lid.
If the sheet music is thin, attach it to a clipboard
before placing it on the music Rest.
2. Raise the topstick located at the right edge.
3. Gently lower the top lid.
Top lid
Topstick
Closing the Top Lid
1. Lift up the top lid.
2. Fold down the topstick.
3. Gently lower the top lid.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Play
Turning the Power On/Off
9
Once the connections have been completed (p. 14), turn on power to your various devices in the order specified. By turning on
devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.
ON
OFF
1
2
Turning the Power On
Turning the Power Off
1. Move the [Volume] slider all the way to the left to
minimize the volume.
1. Move the [Volume] slider all the way to the left to
minimize the volume.
2. Press the [Power] switch.
2. Press the [Power] switch.
The power will turn on, and [Piano] button and [Reverb]
button will light.
The screen goes blank and the power is turned off.
After a brief interval, you’ll be able to produce sounds
by playing the keyboard.
If you need to turn off the power completely, first turn off
the POWER switch, then unplug the power cord from the
power outlet. Refer to Power Supply (p. 10).
•
•
This unit is equipped with a protection circuit. A brief interval
operate normally.
Always make sure to have the volume level turned down
before switching on power. Even with the volume all the way
down, you may still hear some sound when the power is
switched on, but this is normal, and does not indicate a
malfunction.
3. Use the [Volume] slider to adjust the volume
(p. 17).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Play
Adjusting the Sound’s Volume
Here’s how to adjust the volume of your keyboard playing or the playback volume of an internal song or USB memory song.
If headphones are connected, use the [Volume] slider to adjust the headphone volume.
Min
Max
1. Turn the [Volume] slider to adjust the overall volume.
Adjust the volume while you play the keyboard to produce sound.
Turning the knob toward the right will increase the volume, and turning it toward the left will decrease the volume.
Adjusting the Brightness of the Display
You can adjust the brightness of the LX-10F’s display.
1. Turn the [Display Contrast] knob to adjust the brightness.
*
You may notice something like vertical lines in the screen, but this is due to the characteristics of a liquid crystal display, and is not a
malfunction. You can minimize this by using the [Display contrast] knob to adjust the brightness of the screen.
*
The brightness may be affected by the temperature.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Play
Using the Headphones
You can use headphones to enjoy the LX-10F without disturbing those around you, such as at night.
Connecting the Headphones
Using the Headphone Hook
The LX-10F has two headphone jacks, two people can also
use headphones simultaneously.
Whenever you are not using the headphones, you can hang
them on the headphone hook of the LX-10F.
Attaching the Headphone Hook
Wing nut
Headphone hook
1. Press and twist the headphone hook included with
the LX-10F into the hole in the bottom left of the
LX-10F (refer to the figure above).
2. Turn the headphone hook wing nut to secure the
headphone hook.
Do not hang anything other than headphones on the
headphone hook. Doing so may damage the
instrument or the hook.
Cautions when Using Headphones
1. Plug the headphones into the Phones jack.
If headphones are connected, no sound will be output
from the LX-10F’s speakers.
•
•
•
•
To prevent damage to the cord’s internal conductors, avoid
rough handling. When using headphones, mainly try to
handle either the plug or the headset.
2. Use the LX-10F’s [Volume] slider to adjust the
headphone volume (P.17).
Your headphones may be damaged if the volume of a device
is already turned up when you plug them in. Minimize the
volume before you plug in the headphones.
If headphones are connected, a headphone symbol is shown
in the lower left of the screen.
Excessive input will not only damage your hearing, but may
also strain the headphones. Please enjoy music at an
appropriate volume.
Use headphones that have a stereo 1/4” phone plug.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Play
Listening to Demo Songs
The LX-10F comes with demo songs.
*
You won’t be able to play back demo songs if there is an unsaved performance. You’ll need to either delete or save your performance
before playing demo songs (p. 42).
2
1
1. Hold down the [Twin Piano] button and press the
[Function] button.
Listening to the Piano Designer demo songs
The indicators of the four tone buttons, the [Twin Piano]
button, the [Piano Designer] button, and the [Function]
button flash.
1. In step 2, press the [Piano Designer] button.
The piano designer demo screen will appear.
Button with tone demo
[Piano]
Demo content
2. Press the [▲] or [▼] button to select the type
Piano tone demo song
E. Piano tone demo song
Strings tone demo song
Demo song using Guitar tones
of demo.
[E. Piano]
3. Press a blinking tone button.
[Strings]
The demo song for the button you pressed will play.
[Others]
Demo songs using the Piano
Designer function (p. 34) to
demonstrate varieties of sounds
You can repeat steps 2 and 3 to hear other demo
songs.
[Piano Designer]
*
*
All rights reserved. Unauthorized use of this material for
purposes other than private, personal enjoyment is a
violation of applicable laws.
No data for the music that is played will be output from MIDI
Out.
2. Press one of the Tone buttons.
The songs will play consecutively, starting with the demo
song you selected. The button for the song currently being
played back flashes on and off.
When playback of the last song is reached, playback
continues by returning to the first song and playing that
again.
3. To stop playback, press the blinking button.
4. Press the [Twin Piano] button to exit Demo mode.
The indicators of the four tone buttons, the [Twin Piano]
button, the [Piano Designer] button, and the [Function]
button will return to their original state.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Play
Using the Pedals
The pedals perform the following operations. You’ll use
them mainly when playing piano.
You can switch the function of the sostenuto pedal
and soft pedal (p. 58).
If you disconnect the pedal cord from the LX-10F while
the power is turned on, the pedal effect will remain
applied. You must connect or disconnect the pedal
cord while the LX-10F’s power is switched off.
Soft Pedal
About the Adjuster
Sostenuto Pedal
If you feel that the pedal is unstable (for example if you’ve
moved the LX-10F to a different location), you can adjust the
adjuster located on the bottom of the pedals as follows.
Damper Pedal
Damper Pedal (right pedal)
Use this pedal to sustain the sound.
While this pedal is held down, notes will be sustained for an
extended time even if you release your fingers from the
keyboard.
With the damper pedal on an acoustic piano, when you step
on the pedal it will at first offer only a slight amount of
resistance, but as you press down further it will start to feel
much heavier. On the LX-10F, this change in the feeling of
resistance is simulated.
Adjuster
Turn the adjuster to lower it until the adjuster is in firm
contact with the floor. The pedal may be damaged if there is
a gap between the adjuster and the floor. In particular, when
you’ve placed the LX-10F on carpet, you must turn the
adjuster until it is pressing firmly against the floor.
On an acoustic piano, when you step on the damper pedal,
you’ll first hear the sound of the dampers releasing the
strings. Then, you should also be able to hear the sound of
strings adjacent to the ones for the notes actually played
resonate sympathetically, resulting in a rich, resounding
tone.
Additionally, when using half-pedaling techniques, the core
of the sound disappears rapidly while a rich, spacious
reverberation. On the LX-10F, the unique, lingering tones
produced by the half-pedaling technique are reproduced in
addition to released-string sounds (Damper Noise) and
resonating sounds (Damper Resonance).
You can modify the sound of the damper releasing
the string and the sound of the sympathetic
vibration (p. 35).
Sostenuto Pedal (center pedal)
The notes you are pressing when this pedal is depressed will
be sustained.
Soft Pedal (left pedal)
This pedal is used to make the sound softer.
Playing with the soft pedal depressed produces a sound that
is not as strong as when otherwise played with the
equivalent strength. This is the same function as the left
pedal of an acoustic piano.
The softness of the tone can be varied subtly by the depth to
which you press the pedal.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Performing with Various Sounds
In addition to piano sounds, the LX-10F lets you enjoy performing with many other sounds (over 300 types).
These sounds are called “Tones.” The Tones are divided into four groups, each of which is assigned to a different Tone button.
Let’s start by performing with a piano tone.
When you turn on the power, the “Grand Piano1” Tone is selected.
fig.Panel
2
1
1. Press the [Piano] button.
Tone name Tone number
The currently selected tone number and tone name are shown.
2. Press the [-] or [+] button.
A different tone is selected.
About the tones you can select
Button
Description
[Piano] button
Selects a variety of instruments, including grand pianos, honky-tonk pianos, and historical instruments.
Selects various electric piano sounds used in pop or rock, as well as the sound of instruments played using
mallets.
[E. Piano] button
[Strings] button
Selects the sounds of string instruments such as violins, as well as other instruments used in orchestras, which
are appropriate when used for Dual play with a piano sound.
Selects a variety of sounds such as organ, bass, and GM2 sounds (p. 80).
*
*
If you select a tone number from 35 through 42, the keyboard will act as a drum set.
If you’ve selected a tone to which the Rotary effect is applied, pressing the [Others] button will change the
modulation speed of the Rotary effect.
[Others] button
*
*
For some tones, there are keys that do not produce sound.
For details on the tones, refer to “Tone list” (p. 75).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Performing with the Metronome
You can sound the metronome while you perform.
The LX-10F contains a versatile metronome feature. You can change the metronome’s volume and time signature, or change the
way in which it divides the beats.
While the song plays, the metronome will sound at the tempo and time signature of the song.
fig.Panel
1. Press the [Metronome] button.
The [Metronome] button will blink, and the display will indicate “Tempo.”
The metronome will sound.
The [Metronome] button will blink red and green according to the currently selected
time signature; red indicates the strong beats, and green indicates the weak beats.
You can press the [Metronome] button once again to stop the metronome.
Changing the Metronome’s Tempo
fig.Panel
2
1
1. Press the [Metronome] button.
The metronome will sound.
2. Press the [-] or [+] button.
Correspondence between beat and tempo display
0/4, 2/4, 3/4, 4/4,
5/4, 6/4, 7/4
Beat
2/2
3/8
6/8, 9/8, 12/8
Tempo
=5–250
=10–500
=20–999
=7–333
fig.table
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Changing the Metronome’s Time Signature
3
2
1
1. Press the [Metronome] button.
The metronome will sound.
2. Press the [Song] (Tempo) button.
The [Song] (Tempo) button will light orange, and the display will indicate the time
signature.
3. Press the [-] or [+] button.
If you specify “0/4” only the weak beats will sound.
If you record your performance, it will be recorded with the time signature you specify here.
When you play back a song, the metronome’s time signature will be set to the time signature of that song.
Available time signatures
2/2, 0/4, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 3/8, 6/8, 9/8, 12/8
You can change the way in which the metronome’s beats are sounded (p. 57).
You can’t change the metronome’s time signature while a song is playing.
*
Adjusting the Metronome’s Volume
fig.Panel
1. While holding down the [Metronome] button, press the [-] or [+]
button.
The display will indicate the metronome’s volume.
If you set the metronome’s volume to “0” the metronome will not sound.
Metronome volume range
0–10
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Adding a Count-in to Synchronize Your Performance (Count-in)
A series of sounds rhythmically played to indicate the tempo before a song starts is called a “count-in.”
If you sound a count-in, it will be easier for you to synchronize your own performance to the tempo of the playback.
fig.Panel
1
2
1. Press the [Metronome] button.
The metronome will sound.
2. Press the [
] button.
A two-measure count sound will be produced before the song starts playing.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Adding Reverberation to the Sound (Reverb)
You can add a pleasant reverberation to the sounds you play from the keyboard, producing the impression that you are performing
in a concert hall. This effect is called “Reverb.”
fig.Panel
1. Press the [Reverb] button.
The [Reverb] button will light.
If you press the [Reverb] button once again, the button will go out and the reverb effect will be
eliminated.
Adjusting the Depth of the Reverb Effect
fig.Panel
1. While holding down the [Reverb] button, press the [-] or [+] button.
The display will indicate the depth of the reverb effect values.
Reverb depth range
1–10
Higher values apply deeper reverb.
The adjusted setting will return to its original values when you turn off the power. If you wish, you
can have this setting be retained even while the power is turned off (p. 59).
*
You can’t specify the depth of the reverb effect independently for each sound. Reverb is applied at the same depth for each
sound.
*
*
The depth of the reverb effect for the song that’s playing will not change.
The reverb effect is not applied if Twin Piano mode (p. 28) is set to “individual.”
What are Effects?
In addition to reverb, the LX-10F provides a wide variety of other “effects” that can modify the sound in various ways.
An appropriate effect is selected for each different tone.
*
Some tones do not have an effect.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Performing with Two layered Tones (Dual Play)
You can play two tones simultaneously from each note of the keyboard. This feature is called “Dual Play.”
As an example, here’s how to layer piano and strings tones.
fig.Panel
1. Hold down the [Piano] button and press the [Strings] button.
Tone 1
Tone2
Both buttons will light.
When you play the keyboard, you’ll hear both the piano and the strings tones.
About the tones
Tone name
Corresponding button
How to select tones
Tone 1
Left tone button
Press the [-] or [+] button.
Hold down the Tone button for Tone 2 (the rightmost of the lit Tone buttons), and press
the [-] or [+] button.
Tone 2
Right tone button
When you press any tone button, Dual play will be cancelled; you’ll hear only the tone of the button
you pressed.
You can change the pitch of tone 2 in steps of an octave (p. 57).
When you press a damper pedal while using Dual play, the effect will apply to both tone 1 and tone
2, but you may change this so that the effect applies to only one tone (p. 58).
You can change the volume balance of the two tones (p. 56).
*
*
Dual play is not available if Split Play or Twin Piano are turned on.
For some combinations of sounds, the effect is not applied to tone 2, and this may affect how the tone sounds.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Dividing the Keyboard for Two-person Performance (Twin Piano)
You can divide the keyboard into left and right zones so that two people can play the same range of pitches, just as though there
were two pianos.
This function is called “Twin Piano.”
For example, you could use Twin Piano to allow a student to play along with their teacher.
fig.Panel
1. Press the [Twin Piano] button.
The [Twin Piano] button will light.
When you turn Twin Piano on, the keyboard, the pedals, and the tone will change to the following settings.
fig.Panel
Conventional
keyboard
C1
C3
C2
C3
C4
C5
C6
C7
C8
Twin Piano
C4
C5
C6
C3
C4
C5
C6
divide point
Grand Piano 1
Grand Piano 1
The damper pedal
for the left area
The damper pedal
for the right area
When you press the [Twin Piano] button a number of times, the Twin Piano function will turn off
and the [Twin Piano] button will go out.
*
Since some effects (p. 25) will no longer be applied if Twin Piano is turned on, this may change the sound of the tone.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Changing the Way in Which the Sound is Heard (Twin Piano Mode)
fig.Panel
1. Hold down the [Twin Piano] button and press the [-] or [+] button.
Setting
Description
The sound of the right-hand keyboard zone will be heard more loudly from the right speaker than from the left speaker.
The sound of the left-hand keyboard zone will be heard more loudly from the left speaker than from the right speaker.
Pair
The sound of the right-hand keyboard zone will be heard only from the right speaker. The sound of the left-hand keyboard
zone will be heard only from the left speaker.
*
*
The reverb effect will be turned off.
For some tones, the sound may not be split between left and right.
Individual
*
If you play in the left-hand keyboard zone, you won’t hear sound from the headphones that are connected to the right
Phones jack. Conversely, when you play in the right-hand keyboard zone, you won’t hear sound from the left headphones.
The settings you change will return to their original values when you turn off the power.
If you wish, you can have this setting be remembered even while the power is turned off (p. 59).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Playing Different Tones in the Left and Right Sides of the Keyboard
(Split Play)
You can play different tones in the left and right sides of the keyboard, divided at a certain key.
This feature is called “Split Play,” and the key at which the keyboard is divided is called the “Split Point.”
fig.Panel
1. Press the [Twin Piano] button a number of times.
Right-hand Tone
The Split screen will appear.
Left-hand Tone
When Split is turned on, the keyboard settings will be as follows.
fig.Panel
Split Point (Power-up default: F 3)
…
A0 B0 C1 D1 E1 F1 G1 A1 B1 C2
C3
C4
C5
B7 C8
Left-hand Tone
Right-hand Tone
Press the [Twin Piano] button a number of times to turn off Split play; the [Twin Piano] button will
go out.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Changing the Tones of the Left and Right Zones
Changing the right-hand tone
fig.Panel
2
1
1. Press a tone button.
The number and name of tone currently selected for the right-hand zone are shown.
2. Press the [-] or [+] button.
A different tone is selected.
Changing the left-hand tone
fig.Panel
1
2
1. Hold down the [Twin Piano] button and press a tone button.
The number and name of the tone currently selected for the left-hand zone are shown.
2. While holding down the [Twin Piano] button, press the [-] or [+]
button.
A different tone is selected.
You can change the pitch of the left-hand sounds in steps of an octave (p. 57).
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Changing the Keyboard’s Split Point
fig.Panel
Range in which you can specify the split point (B1–B6)
A0
C1
B1 C2
C3
C4
C5
C6
B6 C7
C8
Split Point
Power-up default: F 3
The Split Point belongs to the left-hand section of the keyboard
1. Hold down the [Twin Piano] button and press the key that you want to
be the new split point.
The key you pressed becomes the new split point, and that key will be shown in the
display.
When you release the [Twin Piano] button, the display will return to its previous
indication.
The changed setting will revert to its original state when you turn off the power.
If you wish, you can have this setting be remembered even while the power is turned off (p. 59).
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Transposing the Keyboard (Transpose)
“Transpose” means to shift the pitches produced by the keyboard.
The Transpose function makes it easy to do the following.
•
The pitch of your accompaniment can be adjusted to a singer’s vocal range without changing your
fingering (i.e., without changing the keys you play).
•
A song written in a difficult key with numerous sharps ( ) or flats ( ) can be performed in a key that’s
easier for you to play.
1. Hold down the [Transpose] button and play the key that’s the tonic of
the key into which you want to transpose.
The current transposition setting is shown while you hold down the [Transpose]
button.
You can also change the transposition setting by using the [-] or [+]
buttons while holding down the [Transpose] button.
Transposition range
-6–0–5 (semitone units)
If a setting other than 0 is selected, the [Transpose] button will be lit.
buttons simultaneously.
You can use the [Transpose] button to turn the Transpose function on/off (if the transposition
setting is other than “0”).
The LX-10F allows you to transpose both the keyboard and the song, or just the keyboard, or just
the song (p. 56). With the factory settings, the keyboard and the song will be transposed together.
If the Transpose Mode (p. 56) is set to “Song” (the song playback), the Transpose function will not
affect the pitches of the keyboard.
Example: Use C major fingering to play a song written in E major
1. Hold down the [Transpose] button and press the E note (the tonic note for the key of E major).
Counting from C as a reference point, the tonic note for the key of E major is four chromatic steps higher, so the display
indicates “+4.”
fig.Panel
It will sound
E G
If you play
C E G
B
The transposition value will return to “0” when you switch songs or turn off the power.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing
Disabling the Buttons (Panel Lock)
The Panel Lock setting lets you disable all of the LX-10F’s buttons. In this state, the settings will not change even if you inadvertently
press a button while performing.
fig.Panel
1. Hold down the [Right] button for a while.
Panel Lock will be activated.
The upper right of the display will show a “padlock” symbol, and all button
operations will be disabled.
To cancel Panel Lock, once again hold down the [Right] button for a
while.
Panel Lock will also be cancelled when you turn off the power.
*
*
If you activate Panel Lock while a song is playing or being recorded, playback or recording will stop.
You can’t activate Panel Lock while in Function mode (p. 53) or while in the Demo Song screen.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Piano Sound to Your Taste (Piano Designer)
What is Piano Designer?
The LX-10F lets you adjust the piano sound to your taste by modifying various aspects of a grand piano’s sound, such as its strings,
pedal, and keyboard resonances, as well as the keyboard touch sensitivity.
This function is called “Piano Designer.”
fig.piano
Hammer Noise
String Resonance
Key Touch
Temperament
Adjusting the
piano sound to
your taste
Using Piano Designer
fig.piano
3
2
1
5
1. Press the [Piano Designer] button.
Parameter
The [Piano Designer] button will light, and the Piano Designer screen will
appear.
The “Grand Piano 1” tone will be selected.
2. Press the [▲] or [▼] button to select the item that you want to edit
(p. 35).
Value
3. Use the [-] or [+] buttons to adjust the value.
4. Repeat steps 2–3 to adjust the piano sound to your taste.
5. Press the [Piano Designer] button to return to the tone select screen.
The settings you’ve adjusted will return to their original values when you turn off the power.
If desired, you can have these settings be remembered even while the power is turned off (p. 59).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Piano Sound to Your Taste (Piano Designer)
Piano Designer Settings
Parameter
Value
Description
Adjusts the extent to which the lid of the grand piano is open.
Lid
0–6
The sound will become more mellow as you close the lid of the piano in the screen. The sound will
become brighter as you open the lid of the piano in the screen.
Master Tuning
415.3–440.0–466.2 Hz
Off, 1–10
This adjusts the LX-10F’s standard pitch (the pitch of the middle A note).
This adjusts the damper resonance of the acoustic piano sound (the sympathetic vibration produced in
strings other than those actually played when you press the damper pedal).
Higher settings will make the sympathetic vibration louder.
Damper
Resonance
Fixed, Super Light, Light,
Medium, Heavy,
Super Heavy
Adjusts the touch sensitivity of the keyboard.
If you select “Fixed,” notes will sound at a uniform volume regardless of how strongly you play the
keyboard.
Key Touch
This lets you make further detailed adjustments to the keyboard sensitivity as appropriate for the
strength of your fingers.
Key Touch Offset
-10–0–9
Higher settings will produce a heavier playing feel.
This adjusts the sound produced when the hammer of an acoustic piano strikes the string.
Higher settings will produce a louder sound of the hammer striking the string.
Hammer Noise
Hammer Response
Duplex Scale
-2–0–2
This adjusts the time from when you play a key until the piano sound is heard.
Higher settings will produce slower response.
Off, 1–10
Off, 1–10
This adjusts the sympathetic vibrations of an acoustic piano’s Duplex Scale (p. 36).
Higher settings will make the sympathetic vibration louder.
This adjusts the string resonance of the acoustic piano sound (the sympathetic vibrations of strings for
previously played notes that occur when you play another note).
String Resonance
Off, 1–10
Higher settings will make the sympathetic vibration louder.
This adjusts sympathetic vibrations such as an acoustic piano’s key-off sound (the subtle sound that
occurs when you release a note).
Higher settings will make the sympathetic vibration louder.
Key Off Resonance
Cabinet Resonance
Damper Noise
Off, 1–10
Off, 1–10
Off, 1–10
Adjusts the body resonance of the grand piano itself.
This adjusts the damper noise of the acoustic piano sound (the sound of the damper releasing the
strings when you press the damper pedal).
*
No damper noise will be heard if Damper Resonance is set to “Off.”
You can play classical styles such as Baroque using historic temperaments (tuning methods).
Most modern songs are composed for and played in equal temperament, the most common tuning in
use today. But at one time, there were a wide variety of other tuning systems in existence.
By playing in the temperament that was in use when a composition was created, you can experience
the sonorities of chords originally intended for that song.
Equal, Just Major,
Just Minor, Arabic,
Kirnberger, Meantone,
Pythagorean,
Temperament
Werckmeister
For details, refer to “Temperaments” (p. 36).
When playing with tuning other than equal temperament, you need to specify the temperament key for
tuning the song to be performed (that is, the note that corresponds to C for a major key or to A for a
minor key).
Temperament Key
C–B
If you choose an equal temperament, there’s no need to select a temperament key.
This lets you specify the amount of “stretch tuning,” a tuning method specifically for pianos, in which
the high range is tuned slightly sharper, and the low range is tuned slightly flatter.
If you select “Preset,” a standard tuning curve created for the LX-10F will be used.
If you select “User,” you’ll be able to edit the stretched
tuning yourself. Play the key whose pitch you want to
adjust, then use the [-] or [+] buttons to adjust its pitch.
Off, Preset, User
Stretch Tuning
(User: -50–0–+50)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Piano Sound to Your Taste (Piano Designer)
Temperaments
Temperament
Qualities
In this tuning, each octave is divided into twelve equal steps. Every interval produces about the same
amount of slight dissonance.
Equal
This tuning eliminates ambiguities in the fifths and thirds. It is unsuited to playing melodies and cannot
be transposed, but is capable of beautiful sonorities.
Just Major
The Just tunings differ from major and minor keys. You can get the same effect with the minor scale as
with the major scale.
Just Minor
Arabic
This tuning is suitable for the music of Arabia.
This is an improvement of the Meantone and Just tunings that provides a high degree of freedom of
modulation. Performances are possible in all keys (III).
Kirnberger
Meantone
Pythagorean
This scale makes some compromises in just intonation, enabling transposition to other keys.
This tuning, devised by the philosopher Pythagoras, eliminates dissonance in fourths and fifths.
Dissonance is produced by third-interval chords, but melodies are euphonious.
This temperament combines the Meantone and Pythagorean tunings. Performances are possible in all
keys (first technique, III).
Werckmeister
What is the Duplex Scale?
The Duplex Scale is a system of sympathetically vibrating strings sometimes included in grand pianos.
These sympathetically vibrating strings are not struck directly with hammers, but sound by vibrating in sympathy
with the vibrations of other strings. By resonating with the overtones, these strings add richness and brilliance to
the sound. These sympathetic strings are added only to the high register above approximately C4. Since they do
not have a damper (a mechanism that stops them from sounding), they will continue sounding even after you play
a note and then release it to stop the sound of the string that was actually struck.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Songs
Playing Back Songs
Here’s how to listen to the built-in songs. The LX-10F provides 74 built-in piano songs.
You can also play back songs from a separately sold floppy disk drive, CD drive, or USB memory
(p. 62).
fig.Panel
2
1
3
1. Press the [Song] (Tempo) button a number of times.
The [Song] (Tempo) button will light red.
2. Press the [-] or [+] button to select a song.
The display will indicate “Preset Song.”
3. Press the [
] button.
When the song has played to its end, playback will stop.
To pause the playback, press the [
] button once again.
The next time you press the [
you paused.
] button, playback will resume from where
Fast-forward and rewind
Operation
Button
To beginning of next song
To beginning of current song
Fast-forward the song
Rewind the song
Press the [
] button.
] button.
Press the [
Hold down the [
Hold down the [
] button while the song is playing.
] button while the song is playing.
About the display
fig.screen
Song number
Media Song name
“PU” is shown as the measure number
if the song starts on a weak beat.
Tempo
Time signature
Measure number
For details on the names of the internal songs, refer to “List of internal songs” (p. 78).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Songs
Playing Parts Individually
The parts of an internal song can be selected and played individually. This allows you to practice playing the left or right-hand part of
a song while listening to the other hand played automatically.
Performance parts and tracks
Track button
Each part is assigned to the track
buttons as shown in the illustration.
Muting
You can “mute” a specific part so that it
will not be heard.
*
The [Accomp] button will not light if
you’ve selected a song that does not
contain an accompaniment.
Left-hand
part
Right-hand
part
Accompaniment part
fig.Panel
2
1. Play back a song (p. 37).
2. Press the track button for the part that you don’t want to be played.
The light for the button you pressed will go out, and the selected part will not be heard.
When you press the track button once again so it’s lit, the part will be heard again.
You can change the volume of the muted part (p. 56).
By playing back a song with the accompaniment part muted, you can skip the introduction.
The mute setting will be cancelled when you switch songs.
Practicing the right-hand part by itself
1. Press the [Right] button.
LX-10F will play
go out
The button will go out.
2. Press the [
] button.
The LX-10F will play the left-hand
part and accompaniment part,
allowing you to practice the right-
hand part separately.
Left-hand
part
Right-hand
part
Accompaniment part
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Songs
Playing All Songs Consecutively (All Songs Play)
You can have the LX-10F play all internal songs (or all songs in internal memory, or all songs in USB memory) repeatedly in
succession.
This function is called “All Songs Play.”
fig.Panel
1. Hold down the [Song] (Tempo) button and press the [
button.
]
All Songs Play will be selected, and the screen will show an icon to indicate this.
*
The All Songs Play function will turn off when you stop playback or turn off the
power.
Adjusting the Volume of the Song Playback
You can adjust the volume at which the song plays.
This is helpful when you want to adjust the volume balance between your keyboard playing and the song playback; for example,
when you’re practicing along with a song.
fig.Panel
1. Hold down the [
] button and press the [-] or [+] button.
The volume of song playback is shown while you hold down the [
] button.
Song volume range
0–10
*
The song playback volume is reset to “10” when you turn off the power.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to Songs
Changing the Song’s Tempo
You can change the tempo at which a song plays back.
When you’re practicing along with an internal song, this allows you to slow down the tempo of a difficult song in order to play it
more comfortably.
fig.Panel
2
1
1. Press the [Song] (Tempo) button a number of times.
The [Song] (Tempo) button will light green, and the display will indicate “Tempo.”
2. Press the [-] or [+] button.
The tempo will change.
If desired, you can make the song play back at a fixed tempo without
allowing its tempo to change (p. 57).
Changing the Pitch of the Song (Playback Transpose)
You can change the key of a song’s playback. This is called the “Playback Transpose” function.
ig.Panel
1. Play back the song (p. 37).
2. Hold down the [Transpose] button and press the [-] or [+] button.
The song’s key will change in semitone steps.
f
Transposition range
-6–0–5 (semitone units)
While you hold down the [Transpose] button, the Playback Transpose setting is
displayed.
If the value is anything other than 0, the [Transpose] button will be lit.
setting will return to its original value (0).
You can use the [Transpose] button to turn the Playback Transpose function on/off (if the
transposition setting is other than “0”).
The LX-10F allows you to transpose both the keyboard and the song, or just the keyboard, or just
the song (p. 57). With the factory settings, the keyboard and the song will be transposed together.
*
The Playback Transpose function will not apply if “Transpose Mode” (p. 57) is set to “Keyboard.”
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Recording Your Keyboard Performance
It’s easy to record your own performances.
You can play back a recorded performance to check your playing, or perform along with a recorded performance.
Getting ready to record
fig.Panel
1
4
2
The [Song] (Tempo) button will light red, and the display will indicate “Internal Song.”
2. Press the [-] button a number of times.
The display will indicate “New Song.”
3. Select the tone that you want to use for performing (p. 21).
If desired, sound the metronome (p. 22).
4. Press the [
] button.
The [
] button will light, the [
] button will blink, and the LX-10F will enter recording-standby mode.
] button once again.
If you decide not to record, press the [
Starting/stopping recording
fig.Panel
1. Press the [
] button or play the keyboard.
A two-measure count will be heard (the measure number will be shown as “-2” then “-1” in the lower right of the display),
and then recording will start.
When recording starts, the [
] button and [
] button will light.
A count sound will not sound if you initiated recording by playing the keyboard.
2. Press the [
] button.
Recording will stop.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Listening to the recorded performance
fig.Panel
2
1
1. Press the [
] button.
You will return to the beginning of the recorded performance.
2. Press the [
] button.
The recorded performance will play.
Playback will stop when you press the [
] button once again.
If you press the [
] button while the metronome is sounding, there will be a two-measure
count (count-in) before playback begins.
The recorded performance will be lost when you turn off the power. If you want to keep your recorded
performance, you must save it to internal memory (p. 44) or to USB memory (p. 64).
You won’t be able to play back another song if there is an unsaved performance. You’ll need to either
If the following indication appears
The confirmation message shown at right will appear if you attempt to
select another song while the previously recorded song has not yet
been saved.
Please save your recorded performance to internal memory or USB
memory (p. 64).
•
If you decide to erase your recorded performance, press the [
button.
]
•
If you don’t want to erase your recorded performance, press the [
] button.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Erasing Your Recorded Performance
Here’s how to erase your recorded performance.
fig.Panel
2
1
1. Hold down the [Song] (Tempo) button and press the [
] button.
A confirmation message will appear.
If you decide not to erase the performance, press the [
] button.
2. Press the [
] button.
The recorded performance will be erased.
If you hold down the [
will be erased.
] button while pressing a track button, the performance of only that track
A recorded performance will be erased when you turn off the power.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Saving Your Recorded Performance
If you’ve recorded a performance, your recorded performance will be lost if you turn off the LX-10F’s power before saving
the song. If you want to keep your recorded performance, it is convenient to save it in internal memory. Songs saved in
internal memory will not be lost when you turn off the power.
You can also save your recorded performances on USB memory (sold separately) or on a floppy disk
(sold separately) (p. 64).
fig.Panel
1
3
5
2
4
Getting ready to save
1. Press the [Function] button.
You’ll enter Function mode (p. 53).
2. Press the [▲] or [▼] button to choose “File Menu.”
3. Press the [
] button to go to the “File Menu.”
4. Press the [▲] or [▼] button to choose “Save Song.”
5. Press the [
] button.
A screen will appear, allowing you to edit the song name.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Editing the song name
fig.Panel
Select the character
to change
Switches the type Inserts
of character
• Letters
Deletes
Change
the character
a character a character
2
• Symbols
• Numerals
1. Use the buttons shown in the illustration above to edit the song name.
2. Press the [ ] button to finalize the song name.
A screen will appear, allowing you to select the save destination for the song.
Selecting the save destination for the song
fig.Panel
3
2
1
1. Press the [▼] button.
2. Press the [-] or [+] button to select the save destination.
No song has been saved in song numbers shown as “Empty” in the song name
column.
Choose a song number in which no song has been saved.
If you want to save your song by overwriting an existing song you no longer need,
select the song number of that unwanted song.
Song name
Song number
3. Press the [
] button.
The song will be saved.
Never turn off the power while the screen indicates “Executing...”
*
You can’t select another song if the recorded performance has not yet been saved. Either press the [
recorded performance, or press the [ ] button to save it (p. 42).
] button to erase your
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Deleting a Saved Song
Here’s how to delete a song that you saved to internal memory.
If you want to delete all the songs that are saved in internal memory, initialize the memory (p. 61).
You can also delete songs from USB memory (sold separately) or a floppy disk (sold separately)
(p. 64).
fig.Panel
1
3
5
2
4
Getting ready to delete
1. Press the [Function] button.
You’ll enter Function mode (p. 53).
2. Press the [▲] or [▼] button to choose “File Menu.”
3. Press the [
] button to go to the “File Menu.”
4. Press the [▲] or [▼] button to select “Delete Song.”
5. Press the [
] button.
A screen will appear, allowing you to choose the song to be deleted.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Choosing the song to delete
fig.Panel
2
1
1. Press the [▼] button.
2. Press the [-] or [+] button to select the song that you want to delete.
Deleting the song
fig.Panel
1
2
1. Press the [
] button.
A confirmation message will appear.
2. Press the [
] button.
The selected song will be deleted.
If you decide not to delete the song, press the [
] button.
Never turn off the power while the screen indicates “Executing...”
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Advanced Recording Methods
Recording Each Hand Separately
You can separately record your left-hand performance to the [Left] button and your right-hand performance to the [Right]
button. You can also separately re-record each hand afterward.
Getting ready to record
fig.Panel
2
3
4
1
1. Press the [Song] (Tempo) button a number of times.
The [Song] (Tempo) button will light red, and the display will indicate “Internal Song.”
2. Press the [-] button a number of times.
The display will indicate “New Song.”
3. Press the [
] button.
The [
recorded will blink, and the LX-10F will enter recording-standby mode.
If you decide not to record, press the [ ] button once again.
] button will light, the [
] button and the button of the track to be
4. Press the button for any track that you don’t want to record, so it’s not lit.
Your performance can be recorded separately to the relevant track buttons.
Recorded performances and the track buttons
The performances you record are assigned to the track buttons as follows.
Track button
Recorded performance
Record with only a single button specified
Your performance will be recorded on the specified track.
Your performance will be recorded on only one track
Record with multiple buttons specified
Twin Piano (p. 27), Split Play (p. 29)
Track button
The priority order for recording will be: [Right] button → [Left] button →
[Accomp] button.
Recorded performance
Twin Piano
Right
Split Play
[Right] button
[Left] button
Right-hand tone
Left-hand tone
Left
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Recording and stopping
fig.Panel
1. Press the [
] button.
You’ll hear a two-measure count, and then recording will begin.
Alternatively, you can start recording by playing the keyboard instead of pressing the [
there will be no count-in.
] button. In this case,
When recording begins, the [
] button and [
] button will light.
During the count, “-2” then “-1” will be shown as the measure number in the lower right of the
screen.
2. To stop recording, press the [
] button.
Additional recording
fig.Panel
4
5
6
2
3
1
1. Press the [
] button.
You’ll return to the beginning of the recorded performance.
2. Press the [
] button.
If you want to erase the previously recorded performance and re-record a new
performance, press the [ ] button.
3. If you want to record onto a different track, press the [
] button.
4. Press the button of the track that you want to record, so it’s blinking.
The [
] button will light, the [
] button will blink, and the LX-10F will enter recording-standby mode.
] button once again.
If you decide not to record, press the [
If you select a previously recorded track for recording, your new performance will be overwritten onto that
track, erasing the previously recorded performance.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
5. Press the [
] button.
You’ll hear a two-measure count, and then recording will begin.
Alternatively, you can start recording by playing the keyboard instead of pressing the [
be no count-in.
] button. In this case, there will
When recording begins, the [
] button and [
] button will light.
During the count, “-2” then “-1” will be shown as the measure number in the lower right of the
screen.
*
If you record additional material without erasing the previously recorded performance, the song’s tempo and time signature
will remain as they were when first recorded.
6. To stop recording, press the [
] button.
When you re-record
If you re-record from the beginning, the previously recorded performance will be erased as the new recording
proceeds.
If you want to record an entire performance, erase the previously recorded performance first (p. 43).
fig.zu
1st Pass
2nd Pass
The first Performance is preserved
Listening to the recorded performance
fig.Panel
1
2
1. Press the [
] button.
You’ll return to the beginning of the recorded performance.
2. Press the [
] button.
The recorded performance will play back.
Press the [
] button once again to stop playback.
Your recorded performance will be lost when you turn off the power. If you want to keep your recorded
performance, you must save it to internal memory (p. 44) or USB memory (p. 64).
You can’t play back another song if a recorded performance exists. Erase or save your recorded
performance, and then play back the desired song (p. 42).
By holding down one of the track buttons and pressing the [
] button, you can erase the
performance of just that track. If you erase the performance from all tracks, the display will indicate
“New Song.”
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Recording a Performance You Play Along with a Song
Here’s how you can record a performance that you play along with an internal song or a song from internal memory.
The part you select using the track buttons will be recorded, replacing the previous content of that part.
During recording, you won’t hear the sound of the track whose button you selected.
*
You can’t record along with a song from a music CD, or with a song that consists of audio data.
Getting ready to perform
1. Select the song that you want to play back (p. 37).
2. Select the tone that you want perform (p. 21).
3. Specify the tempo for recording (p. 40).
*
The tempo of your recorded performance will be the tempo of the song you selected for recording.
When you record a performance that you play along with a song, it will be recorded with the time signature of that song.
Getting ready to record
fig.Panel
3
1
2
1. Press the [
2. Press the [
] button (Add On recording).
] button once again.
3. Press the track button of the part that you want to record, so it’s
blinking.
With this setting, you will be listening to the selected song while you record.
The [
] button will light, the [
] button will blink, and the LX-10F will enter recording-standby mode.
] button once again.
If you decide to cancel recording, press the [
Recorded performances and the track buttons
The performances you record are assigned to the track buttons as follows.
Track button
[Right] button
[Left] button
Performance part
Right-hand part
Left-hand part
[Accomp] button
Other performances
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Your Performance
Recording and stopping
fig.Panel
1. Press the [
] button.
You’ll hear a two-measure count, and then recording will begin.
Alternatively, you can start recording by playing the keyboard instead of pressing the [
there will be no count-in.
] button. In this case,
When recording begins, the [
] button and [
] button will light.
During the count, “-2” then “-1” will be shown as the measure number in the lower right of the
screen.
2. Press the [
] button.
Recording will stop.
Listening to the recorded performance
fig.Panel
1
2
1. Press the [
] button.
You’ll return to the beginning of the recorded performance.
2. Press the [
] button.
The recorded performance will play back.
Press the [
] button once again to stop playback.
Your recorded performance will be lost when you turn off the power. If you don’t want to lose your
recorded performance, you must save it to internal memory (p. 44) or to USB memory (p. 64).
You can’t play back another song if a recorded performance exists. Erase or save your recorded
performance, and then play back the desired song (p. 42).
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Settings
Basic Operation in Function Mode
“Function mode” lets you make various settings for playback and recording.
Entering Function mode
fig.Panel
3
2
1
1. Press the [Function] button.
2. Press the [▲] or [▼] button to choose the setting that you
want to edit.
The [Function] button will light, and you’ll be in Function mode.
fig.Screen
3. Press the [
] button to go to the editing screen.
Editing a setting
fig.Panel
1
2
3
1. Press the [-] or [+] button to edit the setting.
3. Press the [Function] button to exit Function mode.
By pressing the [-] [+] buttons simultaneously you can return the
setting to its factory-set value.
The button indicators will return to their previous state.
The edited settings will revert to their original value when you
turn off the power.
For some settings, you can specify that they retain their edited
state even when you turn off the power (p. 59).
For details on the settings that can be saved in this way, refer
to “Items retained by Memory Backup” (p. 79).
2. Press the [Song] (Tempo) button to return to the
previous screen.
If you want to edit other settings, refer to step 2 of “Entering
Function mode” and choose the setting that you want to edit.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Settings
Settings you can change
Adjusting the Keyboard Sensitivity
(Key Touch)
Function
Page
p. 54
p. 44
p. 65
p. 46
p. 61
p. 55
p. 55
p. 55
p. 56
p. 56
p. 56
p. 56
p. 57
p. 57
p. 57
p. 57
p. 58
p. 58
p. 58
p. 68
p. 68
p. 68
p. 69
p. 61
p. 70
p. 58
p. 63
p. 58
p. 58
p. 59
p. 59
Key Touch
You can change the touch sensitivity, or response of the keys.
You can adjust the keyboard touch as appropriate for the playing
strength of the person who is performing.
Save Song
Copy Song
File Menu
Delete Song
Format Media
Setting
Fixed
Description
The sound plays at one set volume, regardless of the
force used to play the keys.
Brilliance
Master Tuning
Equalizer
Super Light
This setting produces the lightest keyboard touch.
You can achieve fortissimo (ff) play with a less
forceful touch than usual, so the keyboard feels
lighter. This setting makes it easy to play, even for
children.
Light
Dual Balance
Master Gain
This sets the standard keyboard touch. You can play
with the most natural touch. This is the closest to the
touch of an acoustic piano.
Mute Volume
Track Assign
Medium
Metronome Pattern
Tempo Mute
You have to finger the keyboard more forcefully than
usual in order to play fortissimo (ff), so the keyboard
touch feels heavier. Dynamic fingering adds even
more feeling to what you play.
Heavy
Transpose Mode
Octave Shift
Super Heavy
This setting produces the heaviest keyboard touch.
Damper Pedal Part
Center Pedal Func
Left Pedal Func
Local Control
MIDI Transmit Ch.
Composer MIDI Out
USB Driver
These settings can also be edited from Piano Designer (p. 35).
Ext. Memory Mode
V-LINK Transmit Ch.
Lyrics
Recommended Tone
CD/Audio Type
Language
Memory Backup
Factory Reset
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Settings
Sounds Settings
3. Press the [
fig.d-EQ-Param.eps
] button.
Adjusting the Sound’s Brilliance (Brilliance)
Here’s how to adjust the brilliance of your keyboard playing or the
playback brilliance of an internal song or USB memory song.
Increasing the value will make the sound brighter.
Setting
-10 (Mellow)–10 (Bright)
4. Use the [▲] or [▼] buttons to select an item.
fig.d-EQ-Param.eps
Matching the Pitch with Other Instruments
(Master Tuning)
When playing ensemble with other instruments and in other such
instances, you can match the standard pitch to another instrument.
5. Use the [-] [+] buttons to change the setting for the
selected item.
The standard pitch generally refers to the pitch of the note that’s
played when you finger the middle A key. For a cleaner ensemble
sound while performing with one or more other instruments, ensure
that each instrument’s standard pitch is in tune with that of the
other instruments. This tuning of all the instruments to a standard
pitch is called “master tuning.”
Indication
Setting
Description
Selects a set of preset equalizer
settings.
EQ Number
1–4
Adjusts the level of the high-
frequency range.
Setting
High Gain
-12–+12 dB
415.3 Hz–440.0 Hz–466.2 Hz
Frequency point in the high-
frequency range.
Generally, this changes the level at
and over this frequency.
High Freq
1.25 k–16 k (Hz)
-12–+12 dB
When the instrument is shipped from the factory, this is set to
“440.0 Hz.”
Adjusts the level of the mid- to
high-frequency range.
High Mid Gain
These settings can also be edited from Piano Designer (p. 35).
Frequency point in the mid- to
high-frequency range.
High Mid Freq
16–16 k (Hz)
This changes the level of the
specified bandwidth centered on
this frequency.
Changing the Equalizer Settings (Equalizer)
Changes the bandwidth of the
mid- to high-frequency range.
The bandwidth affected by the
controls narrows as the value
increases.
You can use the equalizer to modify the tonal character of the sound
by boosting or reducing just the low-frequency or high-frequency
range of the sound.
0.5, 1.0, 2.0, 4.0,
8.0
High Mid Q
1. Enter Function mode, choose “Equalizer,” and press the
Adjusts the level of the low-
frequency range to midrange.
Low Mid Gain
Low Mid Freq
-12–+12 dB
16–16 k (Hz)
[
] button (p. 53).
fig.d-EQ-Param.eps
Frequency point in the low-
frequency range to midrange.
This changes the level of the
specified bandwidth centered on
this frequency.
Changes the bandwidth of the low-
frequency range to midrange.
The bandwidth affected by the
controls narrows as the value
increases.
0.5, 1.0, 2.0, 4.0,
8.0
Low Mid Q
2. Press the [+] button to switch “On.”
fig.d-EQ-Param.eps
Adjusts the level of the low-
frequency range.
Low Gain
Low Freq
-12–+12 dB
100–1k (Hz)
Frequency point in the low-
frequency range.
Generally, this changes the level at
and below this frequency.
*
Sounds may become distorted as the Gain level increases.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Settings
Volume Settings
Adjusting the Dual Play Volume Balance
(Dual Balance)
Changing the Parts Assigned to the Track
Buttons During SMF Playback (Track Assign)
You can adjust the volume balance between the two tones (tone 1
and tone 2) used for Dual Play.
Ordinarily, when playing back SMF music files for Roland Piano
Digital instruments (p. 80), the left-hand part is assigned to the [Left]
button, and the right-hand part is assigned to the [Right] button.
However, right-hand and left-hand part assignments in certain SMF
music files may differ.
Setting
9-1 (tone 1 is louder)–9-9 (same volume)–1-9 (tone 2 is louder)
If these are set to “Auto,” and as a result you are unable to use the
track buttons to control the left- and right-hand parts properly,
change the setting to “2/1 Part” or “3/4 Part.”
Adjusting the Volume (Master Gain)
*
This setting can be used for SMF format songs other than the
internal preset songs. It will not affect internal preset songs.
If you are playing the LX-10F through a connected external system,
there may be cases in which the volume from your external system
is too low even when the LX-10F’s volume is turned to the
maximum setting.
Setting
Description
The part assigned to each track will be determined
automatically, depending on the song file.
Auto
In such cases, you can adjust the master gain setting as follows.
Adjusting the master gain will also affect the volume of the internal
speakers and headphones.
Assigns Part 1 to the [Right] button, Part 2 to the [Left]
button, and the remaining parts to the [Accomp] button.
2/1 Part
3/4 Part
*
The sound may distort if you increase the volume excessively.
Assigns Part 4 to the [Right] button, Part 3 to the [Left]
button, and the remaining parts to the [Accomp] button.
Setting
-12–0–12 dB
After changing this setting, try selecting the song once again.
Using the Sound of a Specific Part as a
“Guide” (Mute Volume)
If desired, you can specify that the sound of a track will play at a
reduced volume rather than going completely silent when you
press a track button and turn off its indicator.
This setting lets you play a specific part at a reduced volume and use
it as a “guide” for your playing.
Setting
Description
0–10
Increasing the value will make the sound louder.
When you turn off the power, the track mute volume will be reset to
“0.”
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Settings
Metronome Setting
Performing Settings
Changing How the Metronome Marks the
Beat (Metronome Pattern)
Specifying What the Transpose will Affect
(Transpose Mode)
You can set the metronome to play at even smaller intervals.
The metronome will sound when you enter the setting screen.
This setting specifies what the transpose will affect.
the keyboard, the pitch of only the song, or the pitch of only the
keyboard.
Setting
Description
Normal
usual sound
Setting
Description
dotted half note
half note
-
Keyboard notes
Transpose (p. 32)
Keyboard
Song playback
Playback Transpose (p. 40)
Song
dotted quarter note
quarter note
Keyboard & Song
Keyboard notes and song playback
dotted eighth note
eighth note
Changing the Pitch of the Tone in Octave
Steps (Octave Shift)
sixteenth note
You can change the pitch of the Tone 2 in Dual Play (p. 26) and
Lower tone in Split Play (p. 29) an octave at a time.
Double
Triplet
Shuffle
note added to back beat of every beat
added notes sound every beat as a triplet
notes added to create a shuffle
Altering the pitch in one-octave units in this way is called “Octave
Shift.”
For example, you can raise the pitch of the Lower Tone to the same
pitch of the Upper Tone in Split Play.
Setting
Playing Back at a Fixed Tempo
(Tempo Mute)
-2–0–+2
Some of the internal songs have a tempo that varies during the
song.
If desired, you can make these songs play at a fixed tempo.
Setting
Description
Tempo changes recorded in the song will be ignored, and the
song will play at a fixed tempo.
On
The song will play according to the tempo changes it
contains.
Off
If Tempo Mute is turned on, the tempo indication in the screen will
be highlighted.
fig.d-EQ-Param.eps
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Settings
Pedal Settings
Setting the Type of CD To be
Played Back (CD/Audio Type)
Changing How the Pedal Effects Are
Applied (Damper Pedal Part)
The LX-10F may be unable to correctly recognize the type of CD
being used. In such instances, you can specify the type of CD
manually.
When you press the damper pedal during Dual play or Split play, the
pedal effect is normally applied to both tones, but you can also
select the tone to which the effect is to be applied.
Setting
Description
Auto
The CD type is detected automatically
General CDs for Player Piano contain audio and MIDI
data, and the data format may vary from one CD to
the next. If the CD’s data format does not match the
LX-10F’s settings, a “beep” will sound. Certain
general Piano player CDs may not be playable on
the LX-10F.
Setting
Description
Type A
Type B
Right & Left
All enabled
Applied only to the Tone 1 (in dual mode)/Right-hand
Tone (in split mode)
Right
Left
Applied only to the Tone 2 (in dual mode)/Left-hand
Tone (in split mode)
Commercial Audio CD
(CDs other than those designed for use with the
player piano)
Stereo
Changing How the Pedals Work
(Center/Left Pedal Func)
*
Note that some commercial player piano CDs cannot be played back
on the LX-10F.
When you turn on the power, the left pedal functions as the soft
pedal, and the center pedal functions as the sostenuto pedal (p. 20).
You can change the function of the pedal to a variety of other
operations.
Changing the Language Displayed
in the Screen (Language)
You can change the language that is displayed in the screen.
Setting
Description
Setting
Sets function to soft pedal.
Soft
*
Selectable only for the left pedal.
English, Japanese
Sets function to sostenuto pedal.
Selectable only for the center pedal.
Sostenuto
Play/Stop
*
The pedal will have the same function as the [
button.
]
Pressing the pedal will layer on Tone 2, used for Dual
play.
Layer
*
The Layer function can be applied only when using
Dual play.
Pressing the pedal will layer on a sound one octave
higher.
Octave
*
The Octave function cannot be applied while using
Twin Piano, Dual play, or Split play.
*
“Layer” and “Octave” cannot be specified simultaneously for the
center and left pedals.
Switching On/Off the Display of
Lyrics (Lyrics)
This lets you specify whether lyrics will be displayed in the screen
when you play back song data that contains lyrics.
Setting
On
Description
Lyrics will be displayed.
Lyrics will not be displayed.
Off
This is set to “On” at the factory.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Settings
Storing Your Settings
(Memory Backup)
Restoring the Factory Settings
(Factory Reset)
The settings you edit in Function mode will return to their factory-
set values when you turn off the power, but the “Memory Backup”
function lets you store these settings so that they will not change
even when you turn off the power.
When you execute the “Factory Reset” function, the settings you’ve
edited in Function mode will be restored to their factory-set state.
Execute this function when you want the settings you saved using
the Memory Backup function to be restored to the state they were
in when you purchased the LX-10F.
1. Enter Function mode, choose “Memory Backup,” and
When you execute “Factory Reset,” all stored settings will be
erased and returned to the factory settings.
press the [
] button (p. 53).
fig.d-Backup2.epsfig.d-EQ-Param.eps
This function will not erase the songs from internal memory or
external memory such as separately sold USB memory.
If you want to erase internal memory or external memory such
as USB memory, refer to “Initializing the Memory (Format
Media)” (p. 61).
1. Enter Function mode, choose “Factory Reset,” and press
2. To store the settings, press the [
] button.
the [
] button (p. 53).
If you decide not to store the settings, press the [Song] (Tempo)
button.
fig.d-EQ-Param.eps
fig.d-EQ-Param.eps
2. To execute Factory Reset, press the [
] button.
If you decide not to execute Factory Reset, press the [Song] (Tempo)
button.
3. To execute the operation, press the [
] button.
fig.d-EQ-Param.eps
If you decide to cancel, press the [
] button.
fig.d-EQ-Param.eps
3. If you’re sure you want to execute, press the [
]
When the memory backup has been completed, the Function mode
menu screen will appear.
button.
To cancel, press the [
fig.d-EQ-Param.eps
] button.
Never turn off the power while the settings are being saved.
For details on the items that are saved, refer to “Parameters
Stored in Memory Backup” (p. 79).
The factory reset will be executed.
Never turn off the power while the Factory Reset is being
executed.
When the factory reset is completed, the following screen will
appear.
fig.d-EQ-Param.eps
4. Turn the power off, and then on again (p. 16).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Connecting a Media
You will be able to accomplish the following once you’ve connected external media (CD drive, floppy disk drive, or USB memory).
Device
What you can do
CD drive
Play back music CDs, SMF music files, and songs from a VIMA CD-ROM (VIMA TUNES sold by Roland)
Play back SMF music files, and save performance data
Floppy disk drive
USB memory
Play back SMF music files, save performance data, and play back audio files
*
If you’re using new USB memory, you’ll need to initialize (format) it on the LX-10F. For details, refer to “Initializing the Memory” (p. 61).
Installing the CD Drive
Installing the Floppy Disk Drive
Attach the CD drive as shown the figure, using the mounting holes
on the LX-10F’s bottom panel.
Attach the floppy disk drive as shown the figure, using the
mounting holes on the LX-10F’s bottom panel.
*
For details of the attachment or connecting, refer to the owner’s
manual of the CD drive.
*
For details of the attachment or connecting, refer to the owner’s
manual of the floppy disk drive.
fig.aaa
fig.aaa
*
Use a floppy disk drive sold by Roland. We cannot guarantee
operation if any other floppy disk drive is used.
*
Use a CD drive sold by Roland. We cannot guarantee operation if
any other CD drive is used.
Connecting USB Memory
Precautions Concerning Use of the CD
Connect the USB memory to the External Memory connector as
•
•
•
•
•
You cannot play back CD-R/RW disks to which audio tracks
have been added or CDs containing both audio tracks and data
(CD Extra).
shown the figure.
fig.aaaa
The LX-10F is capable of playing back only commercial CDs
that conform the official standards-those that carry the
“COMPACT DISC DIGITAL AUDIO” logo.
The usability and sound quality of audio discs that incorporate
copyright protection technology and other non-standard CDs
cannot be guaranteed.
*
*
Carefully insert the USB memory all the way in—until it is firmly in
place.
For more detailed information on audio discs featuring
copyright protection technology and other non-standard CDs,
please consult the disc vendor.
Use a USB memory sold by Roland. We cannot guarantee operation
if any other USB memory is used.
You cannot save songs and styles to CDs, and you cannot
delete songs or styles recorded to CDs. Furthermore, you
cannot format CDs.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
5. Press the [
] button.
Initializing the Memory (Format Media)
A confirmation message will appear.
fig.aaaa
Here’s how you can completely erase all songs that were saved in
internal memory, USB memory (sold separately), or a floppy disk
(sold separately).
Once an initialization is performed, all songs that have been
saved in memory will be erased. The erased data cannot be
recovered, so we recommend that you check the contents of
memory before you proceed.
If you press the [
] button, you’ll return to the previous
screen without initializing.
6. Press the [
] button.
If you’re using new USB memory (sold separately) or floppy
disk (sold separately) with the LX-10F for the first time, you’ll
need to initialize (format) the USB memory or a floppy disk
before using it. The LX-10F can’t use USB memory or a floppy
disk that has not been initialized.
Initialization will begin.
The entire contents of the selected memory will be erased.
Caution when Initializing the Memory
•
•
•
display.
If you want to initialize USB memory or a floppy disk, make the
following preparations before you proceed.
If the screen indicates “Error,” please refer to “Error Messages”
(p. 74).
•
•
Connect your USB memory to the external memory connector.
Connect your floppy disk drive to the external memory connector,
and insert a disk in the drive.
Initializing the LX-10F’s internal memory will not initialize
settings other than the contents of internal memory. If you
want to return settings other than the contents of internal
memory to their factory-set condition, execute the Factory
Reset operation (p. 59).
1. Enter Function mode, choose “File Menu,” and press the
] button (p. 53).
[
•
•
Don’t disconnect the USB memory until USB memory
initialization has been completed.
2. Press the [▲] or [▼] button to choose “Format Media.”
fig.aaaa
While a floppy disk is being initialized, do not eject the disk
from the floppy disk drive or disconnect the cable of the disk
drive.
Changing the External Memory Setting
(Ext. Memory Mode)
3. Press the [
] button.
If you decide not to execute Format Media, press the [Song]
(Tempo) button.
In some cases, when USB memory is connected to the external
memory connector, it may take longer for data to be loaded, or data
may fail to be loaded successfully. If this occurs, you may be able to
solve the problem by changing the external memory setting.
fig.aaaa
1. Enter Function mode, choose “Ext. Memory Mode,” and
press the [
] button (p. 53).
2. Press the [-] or [+] button to edit the setting.
4. Press the [-] or [+] button to select the memory that you
want to initialize.
Setting
Mode 1, Mode 2
Display
Description
Internal memory
USB memory
Floppy disk
3. If you change this setting, turn on the power once again.
Internal Memory
External Memory
Disk
This setting is remembered even when the power is turned off.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Playing Back Songs on External Media
You can play back songs from a CD, USB memory, or a floppy disk.
You can play back songs that are music data (p. 80) or audio files (p. 73).
1. Prepare the external media that contains the song you
want to play.
3. Select the song that you want to play back.
Refer to “Selecting a song” below.
Insert the floppy disk into the floppy disk drive, or the CD into the
CD drive.
4. Press the [
] button.
For details on operations during playback, refer to step 3 of “Playing
Back Songs” (p. 37).
2. Press the [Song] (Tempo) button a number of times.
The [Song] (Tempo) button will light red, and the song select screen
will appear.
Selecting a song
Button operations
Select a song
* Press the [-] or [+] button to select a song.
Order in which memories are selected
1. The song to be newly recorded
Display
External Memory USB memory
Discription
CD
CD-ROM
Select a memory
Music CD
Disk
Music CD
Floppy Disk
2. Songs from CD, USB memory, or
floppy disk
Select a song
* This cannot be selected if nothing is
connected to the external memory
connector.
Select a memory
Select a memory
Select a song
Shown for audio files
3. Songs from internal memory
* This cannot be selected if there are
no songs.
Select a song
4. Internal songs
Select a song that’s inside a folder
•
To select a song that’s inside a folder, select the folder and press the [
] button.
•
To exit the folder, select “Up” and press the [ ] button.
*
If a folder contains 500 or more files and/or folders, some of the files and folders may
not be displayed.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Adjusting the Volume of an Audio File or
Music CD
Minimizing the Sounds in the Center
(Center Cancel)
You can adjust only the volume of an audio file or music CD.
Sounds on a music CD or audio file that are heard from the center
(typically the vocal or melody instrument) can be minimized in the
playback.
1. Play back the audio file or music CD (p. 62).
1. Play back the audio file or music CD (p. 62).
2. Hold down the [
button.
] button and press the [-] or [+]
2. Press the [Right] button so its light is turned off.
The volume of the melody or vocal will decrease.
Setting
*
For some songs, the sound heard from the center may not
disappear completely.
0–10
To turn off the Center Cancel function, press the [Right] button.
The Center Cancel function will also be turned off when you
select a different song.
Changing the Tempo of an Audio File or
Music CD
*
For some songs, using Center Cancel may affect the tonal character.
You can change the tempo of an audio file or a song from a music
CD.
Switching VIMA TUNES Recommended
Tones (Recommended Tone)
1. Press the [Song] (Tempo) button a number of times.
The [Song] (Tempo) button will light green, and the display will
indicate “Audio Tempo.”
You can connect a commercially available USB CD drive to the LX-
10F, and play back separately sold CD-ROMs created for the VIMA
(VIMA TUNES p. 80).
2. Press the [-] or [+] button.
Songs on VIMA CD-ROM (VIMA TUNES) are programmed with
“recommended tones” suitable for each song.
Setting
75–100–125 (%)
When you select a song from a VIMA CD-ROM (VIMA TUNES),
recommended tones will be assigned to the LX-10F’s [E. Piano],
If you select a different song or turn off the power, the tempo
will revert to a setting of “100.”
tone buttons will blink. When you press a flashing Tone button, the
recommended tone is then selected, enabling you to perform the
selected song using a tone matched to that song as it plays back.
Changing the Playback Pitch of a Song
(Playback Transpose)
You can set the LX-10F so that the recommended tones are
automatically assigned or not assigned.
1. Enter Function mode, choose “Recommended Tone,” and
You can also change the playback pitch for a music CD song or an
audio file (Playback Transpose; p. 40).
press the [
] button (p. 53).
1. Play back the audio file or music CD (p. 62).
2. Press the [-] or [+] button to switch “On” or “Off.”
2. While holding down the [Transpose] button, press the [-]
or [+] button.
Setting
Description
When you select a song from a VIMA CD-ROM (VIMA TUNES),
recommended tones will automatically be assigned to the
LX-10F’s [E. Piano], [Strings], and [Others] tone buttons.
On
Setting
The recommended tones are not used, and only the LX-10F’s
internal tones can be selected.
-6–0–5 (semitone units)
Off
*
If you’ve selected a music CD song or audio file, using Playback
Transpose may affect the tonal character.
This is set to “On” at the factory.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Saving Your Recorded Performance on
External Memory
Deleting a Song From External Memory
Here’s how to delete a song that you saved on USB memory or a
floppy disk.
Here’s how to save your recorded performance to USB memory or a
floppy disk.
Getting ready to delete
Getting ready to save
1. Enter Function mode, choose “File Menu,” and press the
[
] button (p. 53).
1. Enter Function mode, choose “File Menu,” and press the
[
] button (p. 53).
2. Press the [▲] or [▼] button to choose “Delete Song.”
fig.aaaa
2. Press the [▲] or [▼] button to choose “Save Song.”
fig.aaaa
3. Press the [
] button.
3. Press the [
] button.
Selecting the song to delete
Changing the name of a song
1. Press the [-] or [+] button to select either “External
Memory” or “Disk.”
1. Edit the song name (p. 45).
fig.aaaa
fig.aaaa
2. Press the [▼] button.
Choosing a save destination, and saving
3. Press the [-] or [+] button to select the song that you want
to delete.
1. Press the [-] or [+] button to choose “External Memory”
or “Disk.”
fig.aaaa
Deleting the song
1. Press the [
] button.
A confirmation message will appear.
fig.aaaa
2. Press the [▼] button.
3. Press the [-] or [+] button to select the save destination.
4. Press the [
] button.
2. Press the [
] button.
The selected song will be deleted.
Never turn off the power while the display indicates
“Executing...”
If you decide not to delete, press the [
] button.
*
*
You can’t select another song if the recorded performance has not
been saved. Please save the recorded performance (p. 42).
Never turn off the power while the display indicates
“Executing...”
If you want to erase an unwanted song and replace it with the newly
saved song, select the number of the unwanted song.
*
You can’t select another song if the recorded performance has not
been saved. Please save the recorded performance (p. 42).
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Copying the Song
Songs that have been saved in internal memory can be copied to USB memory.
Alternatively, songs stored on a USB memory device can be copied to internal memory.
Getting ready to copy
Copying the song
1. Enter Function mode, choose “File Menu,” and press the
1. Press the [
] button.
[
] button (p. 53).
The selected song will be copied.
*
You cannot copy songs on audio files.
2. Press the [▲] or [▼] button to choose “Copy Song.”
fig.aaaa
Never turn off the power while “Executing...” is shown in the
display.
Save and Copy
A song you’ve recorded can be saved in internal memory or
USB memory.
3. Press the [
] button.
Songs saved in internal memory can be copied to external
memory, such as USB memory.
fig.aaaa
Selecting the song to copy
LX-10F
Save
Save
Recorded Song
1. Press the [-] or [+] button to select either “External
Memory” or “Disk.”
fig.aaaa
1
2
3
4
Copy
Copy
LX-10F
Internal Memory
External Memory
USB Memory,
2. Press the [▼] button.
Floppy Disk Drive
(Sold Separately)
3. Press the [-] or [+] button to select the song that you want
to copy.
If you choose “Copy all,” all songs in the copy-source memory
will be copied.
4. Press the [
] button.
5. Press the [-] or [+] button to select the copy-destination
number.
fig.aaaa
Numbers for which a song name is shown already contain a song.
If you select a number at which a song has already been saved, and
execute the copy operation, the previously saved song will be
deleted.
If you don’t want to delete an existing song, select an unused
number.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Connecting to Audio Equipment
If you connect the LX-10F to powered speakers or to an audio system that has line input jacks, you’ll be able to hear the LX-10F’s sound from your
powered speakers or audio system. If you connect your portable audio player or other audio playback device to the LX-10F, you’ll be able to hear its
sound via the LX-10F. Use audio cables (sold separately) to make connections.
Caution when making audio connections
To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before
making any connections.
When connection cables with resistors are used, the volume level of equipment connected to the inputs jacks may be low. If this happens, use
connection cables that do not contain resistors.
Having Audio from an External Device be
Sounded Through the LX-10F.
Connecting Speakers to the LX-10F and
Outputting Sounds
fig.aaaa
fig.aaaa
Output jacks
Input jacks
1/4" plug
Amplified Speakers,
Audio System, etc.
RCA PIN
Output (Line out) jack
Portable audio
player, etc.
Input (Line In) jacks
1. Turn the volume all the way down on the LX-10F and on
the audio device.
1. Turn the volume all the way down on the LX-10F and on
the speaker.
2. Turn off the power to the LX-10F and audio device.
2. Turn off the power to the LX-10F and speakers.
3. Use audio cables (sold separately) to make the
connection.
3. Use audio cables (sold separately) to make the
connection.
4. Switch on the connected audio device.
5. Switch on the LX-10F.
4. Switch on the LX-10F.
5. Switch on the connected speakers.
6. Adjust the volume level on the LX-10F and the connected
audio device.
6. Adjust the volume level on the LX-10F and the connected
speakers.
The sounds from the connected audio device are played by the LX-
10F.
When you play the LX-10F’s keyboard, the sound is played from the
connected speakers.
Adjust the volume by using the controls of your audio device.
Turning Off the Power
Turning Off the Power
1. Turn the volume all the way down on the LX-10F and on
the speakers you’re about to connect.
1. Turn the volume all the way down on the LX-10F and on
the audio device you’re about to connect.
2. Turn off the connected speakers.
3. Turn off the LX-10F.
2. Turn off the LX-10F.
3. Turn off the connected audio device.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Connecting to MIDI Devices
By connecting an external MIDI device and exchanging performance data, you can control one device from the other.
For instance, you can output sound from the other instrument or switch Tones on the other instrument.
What’s MIDI?
MIDI, short for “Musical Instrument Digital Interface,” was developed as a universal standard for the exchange of performance data between
electronic instruments and computers.
The LX-10F is equipped with MIDI connectors to let it exchange performance data with external devices. These connectors can be used to
connect the LX-10F to an external device for even greater versatility.
Connecting a MIDI Sequencer to the LX-10F
Producing Sounds from a MIDI Sound
Module by Playing the LX-10F
fig.aaaa
fig.aaaa
MIDI Out/In connectors
MIDI Out connector
MIDI cable
MIDI cable
OUT
MIDI
IN
MIDI
OUT
THRU
IN
MIDI Sequencer
MIDI Sound Module
When the LX-10F is connected to a MIDI sequencer, set it to
Making the Connection
“Local Off” (p. 68).
1. Turn the volume all the way down on the LX-10F and on
the MIDI device.
2. Switch off the power to the LX-10F and the MIDI device.
3. Use a MIDI cables (sold separately) to connect the MIDI
connectors to each other.
4. Switch on the power to the LX-10F and the connected
MIDI device.
5. Adjust the volume level on the LX-10F and the connected
MIDI device.
6. You should also set the MIDI transmit channel as needed.
For details on the MIDI transmit channel, refer to “MIDI
Transmit Channel Settings (MIDI Transmit Ch.)” (p. 68).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
1. Enter Function mode, choose “Local Control,” and press
the [ ] button (p. 53).
Preventing Doubled Notes When
Connected to a Sequencer (Local Control)
2. Press the [-] or [+] button to switch “On” or “Off.”
When you have a MIDI sequencer connected, set this parameter to
Local Off.
Setting
Description
The Local Control is set to On.
The keyboard and sequencer are connected to the internal
sound generator.
Since the Thru function of your sequencer will normally be turned
on, notes played on the keyboard or played back by the sequencer
will be transmitted to the sound generator by the two routes (1) and
(2) shown in the illustration, causing notes to be sounded in
duplicate or to be cut off unnaturally. To prevent this, the setting
On
The Local Control is set to Off.
The keyboard and sequencer are not connected to the
internal sound generator. Playing the keyboard or playing
back a song will not produce sound.
Off
called “Local Off” is used to disconnect the route in (1).
fig.aaaa
Local On
(1)
Sequencer
Memory
MIDI Transmit Channel Settings
(MIDI Transmit Ch.)
MIDI
OUT
MIDI
IN
Sound
Generator
transmit. MIDI uses sixteen “MIDI channels,” which are numbered 1
through 16. By connecting MIDI devices and specifying the
appropriate MIDI channel for each device, you can play or select
sounds on those devices.
MIDI
OUT
MIDI
IN
Soft Thru On
(2)
Each note played is sounded twice
The LX-10F will receive all sixteen channels (1–16).
Local On:
The keyboard and sequencer are connected to the internal sound
generator.
1. Enter Function mode, choose “MIDI Transmit Ch.,” and
press the [
] button (p. 53).
fig.aaaa
Sound is emitted
2. Press the [-] or [+] button to edit the setting.
Setting (Channel)
Sound Generator
Local On
Off, 1–16
When set to “Off,” none of the data describing what you play
on the keyboard will be transmitted.
Local Off:
Sending Recorded Performance Data to a
MIDI Device (Composer MIDI Out)
The keyboard and sequencer are not connected to the internal
sound generator. No sound will be produced by the keyboard when
it is played.
When Composer MIDI Out is “On,” you can send performance data
recorded with the LX-10F to a connected MIDI device or computer.
fig.aaaa
No sound produced
1. Enter Function mode, choose “Composer MIDI Out,” and
press the [
] button (p. 53).
Sound Generator
Local Off
2. Press the [-] or [+] button to switch “On” or “Off.”
Setting
On
Description
Performance data is transmitted.
Performance data is not transmitted.
Off
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Connecting a Computer
The following become possible once you connect a USB cable
(available separately) between the USB connector on the LX-10F’s
left end of the bottom panel and the USB connector of your
computer.
Changing the USB Driver Settings
(USB Driver)
•
•
You can use the LX-10F to play sounds from SMF music files played
back with MIDI software.
Normally, you don’t need to install a driver in order to connect the
LX-10F to your computer. However, if some problem occurs, or if the
performance is poor, using the Roland original driver may solve the
problem.
By exchanging MIDI data with sequencer software, you can save
songs recorded with the LX-10F to your computer, and enjoy a
variety of musical control and editing features.
Specify the USB driver you want to use, and then install the driver.
fig.aaa
1. Enter Function mode, choose “USB Driver,” and press the
[
] button (p. 53).
2. Press the [-] or [+] button to switch “Generic” or
“Original.”
Setting
Description
Choose this if you want to use the standard USB driver that
was included with your computer.
Generic
Normally, you should use this mode.
USB connector
Choose this if you want to use a USB driver downloaded
from the Roland website.
Original
If you change this setting, turn on the power once again.
This setting is remembered even when the power is turned off.
Computer
For details on downloading and installing the Roland original
driver, refer to the Roland website.
USB cable
USB connector
Roland website
Here you can download the original driver, and view the
installation procedure and operating requirements.
*
Connect the LX-10F to your computer as shown right.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to Other Devices
Using the V-LINK Function
Connecting the LX-10F to a V-LINK compatible image device allows you to control the images with the LX-10F.
*
To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before
making any connections.
V-LINK
V-LINK (
) is a function that allows music and images to be performed together. By using MIDI to connect two or more V-LINK
compatible devices, you can easily enjoy performing a wide range of visual effects that are linked to the expressive elements of a music
performance.
fig.aaa
1. Hold down the [Reverb] button and press the
Specifying the V-LINK Transmit Channel
[Transpose] button.
fig.aaa
Here’s how to specify the channel on which messages used to
control video will be sent.
1. Enter Function mode, choose “V-LINK Transmit Ch.,” and
press the [
] button (p. 53).
2. Use the [-] or [+] button to edit the setting.
When the V-LINK function is on, the V-LINK icon appears on the
screen.
Setting
1–16
You can control images using the twelve keys at the left end of the
keyboard.
fig.aaa
A0 B0 C1 D1 E1 F1 G1
A0 – G#1
*
While V-LINK is switched on, no sound is produced when you press
any of the twelve keys at the left end of the keyboard.
To cancel V-LINK, hold down the [Reverb] button and press the
[Transpose] button.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you think there’s a problem, read this first.
Symptom
Cause/Action
Page
Power does not turn on
Is the power cord connected correctly?
p. 14
Since the LX-10F uses a liquid crystal screen, it may happen that no text or graphics appear in the screen if the
temperature is below zero degrees Celsius (32 degrees Fahrenheit).
Nothing appears in the screen
—
Is the pedal connected correctly?
Plug the cable firmly into the pedal connector.
p. 14
If you disconnect the pedal cord from the LX-10F while the power is on, the pedal effect may remain “stuck” in the
On condition.
—
You must power-off the LX-10F before connecting or disconnecting the pedal cord.
Could you have changed how the pedal effect is applied?
If the damper pedal part is set to Right, the pedal will apply only to the right tone; if it is set to Left, the pedal will
apply only to the left tone.
p. 58
p. 27
p. 58
Pedal does not work, or is “stuck”
Could Twin Piano be turned on?
If Twin Piano is on, the right pedal will affect only the right-hand keyboard zone and the left pedal will affect only
the left-hand keyboard zone.
Could you have changed the function of the pedal?
If you’ve switched the function of the soft pedal or sostenuto pedal, these pedals will not operate as the soft pedal
or sostenuto pedal.
Are you using (optional) Roland USB memory?
Reliable performance cannot be guaranteed if you use non-Roland USB memory products.
—
Unable to read from/write to USB memory
“Buzz” is heard from external devices
If you are unable to read or write USB memory successfully, change the External Memory setting.
p. 61
—
Are the external devices connected to more than one AC power outlet?
If you connect external devices, be sure to connect them to the same AC outlet.
Device connected to the Input jacks have
insufficient volume
Could you be using a connection cable that contains a resistor?
Use a connection cable that does not contain a resistor.
—
No sound
Is the speaker cable connected correctly?
p. 14
p. 17
Could the LX-10F’s volume or the volume of the connected equipment be turned down?
Could headphones be connected?
Could there be a plug inserted in a headphone jack?
p. 18
The speakers will not produce sound if headphones or plug are connected to the headphone jacks.
No sound
Has Local Control been set to “Off”?
When Local Control is set to Off, no sound is produced by playing the keyboard. Set Local Control to On.
p. 68
Could Twin Piano mode be set to “Individual”?
If headphones are connected when Twin Piano is “on” and the mode is set to “Individual,” notes played in the left-
hand keyboard zone will not be heard from the headphones connected to the right Phones jack. Similarly, notes
played in the right-hand keyboard zone will not be heard from the headphones connected to the left Phones jack.
p. 28
Has Local Control been set to “Off”?
When Local Control is set to Off, no sound is produced by playing the song. Set Local Control to On.
p. 68
No sound when you play back a song
Could the song volume be set to “0”?
p. 39
Is V-LINK switched on?
No sound from the leftmost notes of the
keyboard
When V-LINK is on, the lowest twelve notes of the keyboard are used to control the image, and will not produce
sound.
p. 70
Are all devices powered on?
—
No sound (when a MIDI device is connected)
Are the MIDI cables connected correctly?
p. 67
p. 68
Do the MIDI channels of the LX-10F and the connected device match?
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Cause/Action
Page
Notes don’t sound right
Sound is not loud enough
Only the high sounds are heard
Is the speaker cable connected correctly?
p. 14
Could you have made Transpose settings?
Is the Master Tune setting appropriate?
Is the setting for the Temperament correct?
Is the settings for the Stretch Tuning correct?
p. 32
p. 55
p. 35
p. 35
Pitch of the keyboard or song is incorrect
Not all the notes you play are sounded
The maximum simultaneous polyphony is 128 voices. If you are playing along with a song and making heavy use
of the damper pedal, the number of notes the LX-10F is attempting to produce may exceed the maximum
polyphony, meaning that some of the notes will drop out.
—
Is the LX-10F in Dual play?
p. 26
Sounds are heard twice (doubled) when the
keyboard is played
When the LX-10F is connected to an external sequencer, set the Local Control to off. Alternatively, the sequencer
could be set so its Soft Thru feature is Off.
p. 68
Tone buttons [E. Piano] [Strings] [Others] also operate as buttons that select “Recommended Tones.”
With the factory settings, connecting a commercially-available CD-ROM drive to the external memory connector
and selecting a song from a CD-ROM produced for the VIMA (VIMA TUNES) will automatically cause sounds
appropriate for that song to be assigned to the [E. Piano], [Strings], and [Others] Tone buttons, so that you can
select “recommended” sounds by pressing one of these buttons.
The wrong instrument is selected when you
press the [E. Piano], [Strings], or [Others]
button
p. 63
You can also make settings so that “recommended” sounds are not automatically assigned.
When you are using Dual play or Split play, and different effects are specified for the two selected tones, the effect
will not be applied to Tone 2 (when using Dual play) or the left-hand tone (when using Split play).
Effect does not apply
—
—
The LX-10F’s piano sound faithfully simulates the depth and resonance of an acoustic piano, and this may give the
impression of reverberation even if you’ve defeated the Reverb effect.
Also, you may be able to eliminate some reverberation by reducing the value set for “Cabinet Resonance.”
Reverberation remains even if You defeat the
Reverb effect
On an acoustic piano, the approximately one and a half octaves of notes at the top of the keyboard will continue
sounding regardless of the damper pedal. These notes also have a somewhat different tonal character. LX-10F
faithfully simulate this characteristic of acoustic pianos. On the LX-10F, the range that is unaffected by the damper
pedal will change according to the key transpose setting.
The sound of the higher notes suddenly
changes from a certain key
—
Is the speaker cable connected correctly?
p. 14
If you hear this in headphones:
Piano sounds that have a brilliant and crisp character contain substantial high-frequency components that may
sound as though a metallic ringing has been added. This is because the character of an actual piano is being
faithfully reproduced, and is not a malfunction. This ringing is more obtrusive if the reverb effect is applied heavily,
so you may be able to minimize it by decreasing the reverb.
High-pitched ringing is heard
—
If you don’t hear this in headphones:
It is likely that there is some other reason (such as resonances within the unit). Please contact your dealer or a
nearby Roland service center.
If you set the volume to the maximum setting, the sound may be distorted depending on how you perform.
If this occurs, turn down the volume.
Alternatively, lower the master gain.
p. 17
p. 56
If you don’t hear this in headphones:
Performing at high volumes may cause the speakers or objects near the LX-10F to resonate. Fluorescent lights or
glass doors may also resonate sympathetically. In particular, this is more likely to occur for lower notes and higher
volumes. You can take the following measures to minimize resonances.
Low notes sound wrong, or are buzzy
•
•
•
Locate the speakers 10–15 cm away from walls or other surfaces.
Keep the volume down.
Move away from the objects that are resonating.
—
If you hear this in headphones:
It is likely that there is some other reason. Please contact your dealer or a nearby Roland service center.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Symptom
Cause/Action
Page
Song does not play correctly
Could the screen be indicating “OK to erase Song?”
Song won’t play
You can’t play back an internal song if internal memory contains performance data you recorded. Erase the
performance data you recorded before you play back the song.
P.43
Could a track be muted?
Only the sound of a particular instrument in a
song does not play
If the button indicator is out, the music on that track is not heard. Press the track button so the indicator is
illuminated.
p. 38
Could the track mute volume be set to other than “0”?
If you set this to “0,” the sound of a muted track will be completely inaudible.
Sound is heard from a muted track
Song volume is low
p. 56
p. 39
Could the song volume be lowered?
Could the Audio files of the format be played?
Audio files of the following format can be played back.
•
•
•
File extension “.WAV”
16-bit linear
“44.1 kHz” sampling rate
—
—
Can’t play back a song saved in USB memory
Is the filename extension “MID”?
Files with other filename extensions cannot be handled as song data.
When playing a song from USB memory, the tempo may become unstable if there is an excessive amount of
performance data.
Song tempo becomes unstable
—
—
—
The song name will not be shown if the song information in the file is empty or consists only of spaces.
Song name in USB memory is not shown
Can’t record / play back
Can’t record
Is the filename extension “MID”?
Files with other filename extensions cannot be handled as song data.
p. 48
p. 51
Has one of the track buttons for recording been selected?
—
Your recorded performance will disappear if you switch off the LX-10F’s power or select a song.
There is no way to recover the lost performance. Before you turn off the power, save your recorded performance
in internal Memory.
The recorded performance disappeared
p. 44
Functions that cannot be used with audio file playback
•
•
•
Reverb (p. 25)
Saving to internal memory (p. 44)
Playback (muting) of individual parts (p. 38)
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Messages
Indication
Meaning
Error: 1
Error: 2
Error: 10
Error: 11
You can only read the music file. It can not be saved.
An error occurred during writing.
The external media’s protect tab may be in the “Protect” (writing prohibited) position, or the external media may not yet be initialized.
No external media is inserted. Insert the external media and try again.
There is not sufficient free memory in the save destination.
Either insert other external media or delete unneeded files and try again.
An error occurred during reading. The external media may be corrupted.
Insert other external media and try again. Alternatively, you can initialize the external media.
Error: 14
Error: 15
Error: 16
The file is unreadable. The data format is not compatible with the LX-10F.
Data was not called up in time for playback of the song. After waiting several seconds, you may be able to play back the song by
pressing the [
] button again.
This audio format is not supported.
Please use 44.1 kHz 16-bit linear WAV format audio files.
Error: 18
Error: 30
Error: 40
The internal memory capacity of the LX-10F is full.
The LX-10F cannot deal with the excessive MIDI data sent from the external MIDI device.
Reduce the amount of MIDI data sent to the LX-10F.
Error: 41
Error: 43
A MIDI cable has been disconnected. Connect it properly and securely.
A MIDI transmission error has occurred. Check the MIDI cable and connected MIDI device.
There may be a problem with the system. Repeat the procedure from the beginning. If it is not solved after you have tried several times,
contact the Roland service center.
Error: 51
Error: 65
The External Memory connector was subjected to excessive current. Make sure that there is no problem with the external media, then
turn the power off, then on again.
*
External Media: USB memory, Floppy Disk, CD-ROM, etc.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Tone List
Piano
Others
No.
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
Name
No.
Name
No.
Name
Piano 1
1
Grand Piano1
Piano + Str.
Harpsichord
Grand Piano2
Piano + Pad
Grand Piano3
MagicalPiano
Rock Piano
Piano+Choir
Honky-tonk
Coupled Hps.
1
ChurchOrgan1
ChurchOrgan2
Combo Jz.Org
Ballad Organ
Accordion
Piano 1w
2
2
Piano 1d
3
3
Piano 2
4
4
Piano 2w
5
5
Piano 3
6
6
Nason flt 8’
Gospel Spin
Full Stops
Piano 3w
7
7
Honky-tonk
Honky-tonk w
E.Piano 1
8
8
9
9
Mellow Bars
Light Organ
Lower Organ
’60s Organ
Aerial Choir
Jazz Scat
10
11
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
GM2
35
36
37
38
39
40
41
42
Detuned EP 1
Vintage EP
’60s E.Piano
E.Piano 2
E. Piano
No.
1
Name
Detuned EP 2
St.FM EP
Pop E.Piano
Vintage EP
FM E. Piano
Vibraphone
EP Belle
Harpvox
2
Glass Pad
EP Legend
EP Phase
3
Angels Choir
Beauty Vox
Soft Pad
4
Harpsichord
Coupled Hps.
Harpsi.w
5
6
Celesta
Female Aahs
Male Aahs
7
’60s E.Piano
Clav.
Harpsi.o
8
Thum Voice
Lunar Strngs
Decay Choir
Dcy ChoirPad
Nylon-str.Gt
Steel-str.Gt
Jazz Guitar
AcousticBass
A.Bass+Cymbl
FingeredBass
BrassSection
Alto Sax
Clav.
9
Mallet Isle
Morning Lite
Marimba
Pulse Clav.
Celesta
10
11
12
13
14
15
*
*
Glockenspiel
Music Box
Vibraphone
Vibraphone w
Marimba
Stage Phaser
Ballad Bells
’70s E.Piano
E.Grand
Strings
Marimba w
Xylophone
TubularBells
Church Bell
Carillon
No.
1
Name
Rich Strings
OrchestraStr
Orchestra
ChamberWinds
Harp
2
Tenor Sax
3
4
Santur
STANDARD Set
ROOM Set
POWER Set
ELEC.Set
5
Organ 1
6
Violin
TremoloOrgan
’60s Organ
Organ 2
7
Velo Strings
Flute
8
ANALOG Set
JAZZ Set
9
Cello
Perc.Organ 1
Chorus Organ
Perc.Organ 2
Rock Organ
Church Org.1
Church Org.2
10
11
12
OrchestraBrs
PizzicatoStr
DecayStrings
BRUSH Set
ORCH.Set
*
*
035–042 are drum sets.
SFX Set
*
Tones indicated by “*” are suitable for
playing layered with a piano tone.
43
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Tone List
No.
90
Name
No.
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
Name
No.
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
Name
Church Org.3
Reed Organ
Puff Organ
Accordion 1
Accordion 2
Harmonica
Bandoneon
Nylon-str.Gt
Ukulele
Attack Pulse
Violin
AnalogBrass2
Soprano Sax
Alto Sax
91
92
Slow Violin
Viola
93
Tenor Sax
Baritone Sax
Oboe
94
Cello
95
Contrabass
Tremolo Str.
PizzicatoStr
Harp
96
English Horn
Bassoon
97
98
Clarinet
99
Nylon Gt o
Nylon Gt 2
Yang Qin
Piccolo
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
Timpani
Flute
Steel-str.Gt
12-str.Gt
Strings
Recorder
Orchestra
’60s Strings
Slow Strings
Syn.Strings1
Syn.Strings3
Syn.Strings2
Choir 1
Pan Flute
Bottle Blow
Shakuhachi
Whistle
Mandolin
Steel+Body
Jazz Guitar
Hawaiian Gt
Clean Guitar
Chorus Gt 1
Mid Tone Gt
Muted Guitar
Funk Guitar1
Funk Guitar2
Chorus Gt 2
Overdrive Gt
Guitar Pinch
DistortionGt
Gt Feedback1
Dist.Rtm Gt
Gt Harmonics
Gt Feedback2
AcousticBass
FingeredBass
Finger Slap
Picked Bass
FretlessBass
Slap Bass 1
Slap Bass 2
Synth Bass 1
WarmSyn.Bass
Synth Bass 3
Clav.Bass
Ocarina
Square Lead1
Square Lead2
Sine Lead
Saw Lead 1
Saw Lead 2
Doctor Solo
Natural Lead
SequencedSaw
Syn.Calliope
Chiffer Lead
Charang
Choir 2
Voice
Humming
Synth Voice
Analog Voice
OrchestraHit
Bass Hit
6th Hit
Euro Hit
Trumpet
Wire Lead
Solo Vox
Dark Trumpet
Trombone 1
Trombone 2
Bright Tb
5th Saw Lead
Bass+Lead
Delayed Lead
Fantasia
Tuba
MuteTrumpet1
MuteTrumpet2
French Horn1
French Horn2
Brass 1
Warm Pad
Sine Pad
Polysynth
Space Voice
Itopia
Brass 2
Bowed Glass
Metallic Pad
Halo Pad
Synth Brass1
Synth Brass3
AnalogBrass1
Jump Brass
Synth Brass2
Synth Brass4
Hammer
Sweep Pad
Ice Rain
Synth Bass 2
Synth Bass 4
RubberSyn.Bs
Soundtrack
Crystal
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Tone List
No.
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
Name
No.
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
Name
Synth Mallet
Atmosphere
Brightness
Goblins
Telephone 1
Telephone 2
DoorCreaking
Door
Echo Drops
Echo Bell
Echo Pan
Star Theme
Sitar 1
Scratch
Wind Chimes
Helicopter
Car Engine
Car Stop
Sitar 2
Car Pass
Banjo
Car Crash
Siren
Shamisen
Koto
Train
Taisho Koto
Kalimba
Jetplane
Starship
Bagpipe
Burst Noise
Applause
Laughing
Screaming
Punch
Fiddle
Shanai
Tinkle Bell
Agogo
Steel Drums
Woodblock
Castanets
Taiko
Heart Beat
Footsteps
Gun Shot
Machine Gun
Laser Gun
Explosion
Concert BD
Melodic Tom1
Melodic Tom2
Synth Drum
TR-808 Tom
Elec.Perc.
Reverse Cym.
Gt FretNoise
Gt Cut Noise
BsStringSlap
Breath Noise
Fl.Key Click
Seashore
Rain
*
In the tone group “Others” when you
hold down the [-] or [+] button to
switch tone in succession, the tones
will stop changing at number 35 and
number 44.
To select the next sound, release the
[-] or [+] button, then press it again.
Thunder
Wind
Stream
Bubble
Bird 1
Dog
Horse Gallop
Bird 2
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Internal Song List
No.
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
Song Name
Composer
No.
1
Song Name
Composer
Türkischer Marsch
Ständchen
Wolfgang Amadeus Mozart
Franz Peter Schubert
Antonín Dvořák
Polonaise op.53
Valse, op.34-1
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Franz Peter Schubert=Franz Liszt
Claude Achille Debussy
Masashi Hirashita
2
Humoreske
3
Nocturne No.20
Die Forelle
Blumenlied
Gustav Lange
4
Alpenglöckchen
Menuett G dur
Venezianisches Gondellied
Alpenabendröte
Farewell to the Piano
Brautchor
Theodor Oesten
5
Reflets dans l’Eau
My Pleasure (*)
La Fille aux Cheveux de Lin
La Campanella
Ludwig van Beethoven
Felix Mendelsshon
Theodor Oesten
6
7
Claude Achille Debussy
Franz Liszt
8
Ludwig van Beethoven
Wilhelm Richard Wagner
Wilma Anderson-Gilman
Carl Czerny
9
Trio Grande (*)
John Maul
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Scherzo No.2
Fryderyk Franciszek Chopin
Fryderyk Franciszek Chopin
Wolfgang Amadeus Mozart
Franz Liszt
Battle of Waterloo
Wiener Marsch
Le Coucou
Étude, op.10-12
Sonate No.15
Louis Claude Daquin
Johann Sebastian Bach
Albert Ellmenreich
François Joseph Gossec
Gustav Lange
Liebesträume 3
Étude, op.10-3
Menuett G dur
Spinnerlied
Fryderyk Franciszek Chopin
Erik Satie
Je te veux
Gavotte
Valse, op.64-1
Fryderyk Franciszek Chopin
Claude Achille Debussy
Fryderyk Franciszek Chopin
Claude Achille Debussy
Johann Strauss, Sohn
Felix Mendelsshon
Heidenröslein
Golliwog’s Cakewalk
Fantaisie-Impromptu
Arabesque 1
Zigeuner Tanz
La Cinquantaine
Csikos Post
Heinrich Lichner
Gabriel Marie
Hermann Necke
An der schönen, blauen Donau
Auf Flügeln des Gesanges
Mazurka No.5
Dolly’s Dreaming Awakening
La Violette
Theodor Oesten
Louis Streabbog
Fryderyk Franciszek Chopin
Erik Satie
Fröhlicher Landmann
Sonatine op.36-1
Sonatine op.20-1
Sonatine No.5
Robert Alexander Schumann
Muzio Clementi
Gymnopédie 1
Étude, op.25-1
Fryderyk Franciszek Chopin
Claude Achille Debussy
Fryderyk Franciszek Chopin
Claude Achille Debussy
Fryderyk Franciszek Chopin
Tekla Badarzewska
Friedrich Kuhlau
Clair de Lune
Ludwig van Beethoven
John Maul
Étude, op.10-5
Late Night Chopin (*)
Fly Free (*)
Dr. Gradus ad Parnassum
Grande Valse Brillante
La prière d’une Vierge
Course en Troïka
To The Spring
John Maul
L’éveil de l’amour (*)
Masashi Hirashita
Peter Ilyich Tchaikovsky
Edvard Hagerup Grieg
Fryderyk Franciszek Chopin
Johann Baptist Strauss
Robert Alexander Schumann
Franz Peter Schubert
Fryderyk Franciszek Chopin
Georg Friedrich Händel
Johannes Brahms
*
All rights reserved. Unauthorized use of this material for purposes
other than private, personal enjoyment is a violation of applicable
laws.
Valse, op.64-2
Radetzky Marsch
Träumerei
*
*
No data for the music that is played will be output from MIDI Out.
Songs marked by an asterisk (*) are original songs composed for
the Roland Corporation. The copyrights to these songs are owned
by the Roland Corporation.
Moments Musicaux 3
Prèlude, op.28-15
Harmonious Blacksmith
Ungarische Tänze 5
Türkischer Marsch
Nocturne No.2
Ludwig van Beethoven
Fryderyk Franciszek Chopin
Felix Mendelsshon
Frühlingslied
Präludium
Johann Sebastian Bach
Felix Mendelsshon
Jägerlied
Menuet Antique
Für Elise
Maurice Ravel
Ludwig van Beethoven
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Parameters Stored in Memory Backup
Parameter
Page
p. 35
p. 35, p. 55
p. 35
p. 35, p. 54
p. 35
p. 35
p. 35
p. 35
p. 35
p. 35
p. 35
p. 35
p. 35
p. 35
p. 55
p. 55
p. 56
p. 56
p. 57
p. 58
p. 68
p. 70
p. 58
p. 58
p. 58
p. 25
p. 31
p. 28
Lid
Master Tuning
Damper Resonance
Key Touch
Key Touch Offset
Hammer Noise
Hammer Response
Piano Designer Settings
Duplex Scale
String Resonance
Key Off Resonance
Cabinet Resonance
Damper Noise
Temperament (Temperament, Temperament Key)
Stretch Tuning
Brilliance
Equalizer (On/Off, Parameter Settings)
Dual Balance
Track Assign
Transpose Mode
Function Mode Settings
Damper Pedal Part
MIDI Transmit Ch.
V-LINK Transmit Ch.
Lyrics
CD/Audio Type
Language
Reverb (On/Off, Depth)
Split Point
Other Settings
Twin Piano Mode
USB Driver Setting
Ext. Memory Mode
p. 69
p. 61
Settings stored immediately, whenever a change
is made (Memory Backup procedure not needed)
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Files That the LX-10F Can Use
What Are Music Files?
Music files contains musical information such as how long the key for a corresponding pitch is played, the force applied to the key played, and other
such information. When the performance data (music file) is sent by the USB memory or CD-ROM, the song will be played exactly as specified by the
data. This is different than an audio CD, since the music file does not contain a recording of the sound itself. This makes it possible to change tempos
and keys freely, allowing you to use it in many different ways.
Regarding Copyright
Use of the song data contained in the LX-10F or any other song data supplied with it for any purpose other than private, personal enjoyment without
the permission of the copyright holder is prohibited by law. Additionally, this data must not be copied, nor used in a secondary copyrighted work
without the permission of the copyright holder.
Please be aware that if you create derivative works that are based on existing copyrighted material, such as commercially available SMF music files,
such works may violate copyright law if used for any purpose other than personal enjoyment. Roland takes no responsibility for any copyright
violation you may commit by creating such works.
The LX-10F Allows You To Use the Following Music Files
VIMA TUNES
General MIDI 2
VIMA TUNES is a Roland specification for music files that contains
The upwardly compatible General MIDI 2 recommendations pick up
images simultaneously. When data bearing the “VIMA TUNES” logo
is played back on a device that bears the same logo, lyrics can be
shown on the screen of a connected external display or television,
letting you enjoy karaoke or watch a slide show.
where the original General MIDI left off, offering enhanced
expressive capabilities, and even greater compatibility. Issues that
were not covered by the original General MIDI recommendations,
such as how sounds are to be edited, and how effects should be
handled, have now been precisely defined. Moreover, the available
sounds have been expanded. General MIDI 2 compliant sound
generators are capable of reliably playing back music files that carry
either the General MIDI or General MIDI 2 logo.
*
*
This instrument (LX-10F) is not able to play back VIMA TUNES
images.
You can specify whether the recommended tones will be assigned
automatically (p. 63).
In some cases, the conventional form of General MIDI, which does
not include the new enhancements, is referred to as “General MIDI
1” as a way of distinguishing it from General MIDI 2.
SMF Music Files
SMFs (Standard MIDI Files) use a standard format for music file that
was formulated so that files containing music file could be widely
compatible, regardless of the manufacturer of the listening device.
An enormous variety of music is available, whether it be for
listening, for practicing musical instruments, for Karaoke, etc.
GS Format
The GS Format is Roland’s set of specifications for standardizing the
performance of sound generating devices. In addition to including
support for everything defined by the General MIDI, the highly
compatible GS Format additionally offers an expanded number of
sounds, provides for the editing of sounds, and spells out many
details for a wide range of extra features, including effects such as
reverb and chorus. Designed with the future in mind, the GS Format
can readily include new sounds and support new hardware features
when they arrive. Since it is upwardly compatible with the General
MIDI, Roland’s GS Format is capable of reliably playing back GM
Scores equally as well as it performs GS music files (music files that
have been created with the GS Format in mind).
SMF with Lyrics
“SMF with Lyrics” refers to SMF (Standard MIDI File) that contains the
lyrics. When Music Files carrying the “
” logo are played back
on a compatible device (one bearing the same logo), the lyrics will
appear in its display.
General MIDI
The General MIDI is a set of recommendations which seeks to
provide a way to go beyond the limitations of proprietary designs,
and standardize the MIDI capabilities of sound generating devices.
Sound generating devices and music files that meets the General
MIDI standard bears the General MIDI logo. Music files bearing the
General MIDI logo can be played back using any General MIDI sound
generating unit to produce essentially the same musical
performance.
XGlite
XG is a tone generator format of Yamaha Corporation, that defines
the ways in which voices are expanded or edited and the structure
and type of effects, in addition to the General MIDI 1 specification.
XGlite is a simplified version of XG tone generation format. You can
play back any XG music files using an XGlite tone generator.
However, keep in mind that some music files may play back
differently compared to the original files, due to the reduced set of
control parameters and effects.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
LX-10F: Digital Piano
<Keyboard>
Keyboard
88 keys (PHA III Ivory Feel Keyboard with Escapement)
Touch: 100 levels, Fixed Touch
Touch Sensitivity
Keyboard Mode
Hammer Response: 10 levels
Whole, Dual (volume balance adjustable), Split (split point adjustable), Twin Piano
<Sound Generator> Conforms to GM2/GS/XGlite
Piano Sound
Max. Polyphony
Tones
SuperNATURAL Piano Sound
128 voices
337 tones (including 8 drum sets, 1 SFX set)
8 types, selectable temperament Key
Preset, User tuning (adjustable in individual notes: -50.0– +50.0 cent), Off
415.3–466.2 Hz (adjustable in increments of 0.1 Hz)
Temperament
Stretched Tuning
Master Tuning
Transpose: -6–+5 (in semitones)
Playback Transpose (with Audio CD/Audio File): -6–+5 (in semitones)
Transpose
Reverb (Off, 1–10),
4-band Digital Equalizer
Only for Piano Tones:
Open/close lid (7 levels), Cabinet Resonance (Off, 10 levels), Hammer Noise (5 levels),
Damper Noise (Off, 10 levels), Duplex Scale (Off, 10 levels), Damper Resonance (Off, 10 levels),
String Resonance (Off, 10 levels), Key Off Resonance (Off, 10 levels)
Effects
Only for Organ Tones:
Rotary Speaker Effect (Slow/Fast)
<Recorder>
Tracks
3 tracks
Recorder section: 1 song
Internal Memory: Max. 99 songs
Songs
Note Storage
Approx. 30,000 notes
Song Select, Play/Stop, Rec, Rewinding, Fast-forwarding, Previous song, Next song, Track Mute, Mute Volume, Tempo,
Tempo Mute, All Songs Play, Count-in, Song Volume
Control
Center Cancel (only for audio playback)
Quarter note = 10 to 500
Audio Playback Speed: 75–125%
Tempo
Resolution
120 ticks per quarter note
Beat: 2/2, 0/4, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 3/8, 6/8, 9/8, 12/8
Volume: 10 levels
Metronome
Metronome Pattern: 11 patterns
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
<Internal Memory>
Songs
Max. 99 songs
Storage format
Standard MIDI Files (Format 0)
<External Memory>
USB Memory
External Storage
Floppy Disk (when using an optional floppy disk drive)
Standard MIDI Files (Format 0/1)
Roland Original Format (i-Format)
Audio File (WAV 44.1 kHz / 16-bit Linear Format)
Audio CDs (CD-DA) (when using a CD drive)
Types of data that can be played
Storage format
Standard MIDI Files (Format 0)
<Others>
Internal Songs
Rated Power Output
Speakers
74 songs
60 W x 2
16 cm x 2 (with Speaker box), (8 cm x 12 cm) x 2, 5 cm x 2
128 x 64 dots Graphic monochrome LCD (with backlit)
English, Japanese
Display
Language
Lyrics
Yes (Built-in Display)
Control
Volume, LCD Contrast
Damper (Progressive Damper Action Pedal, capable of continuous detection),
Soft (capable of continuous detection, function assignable), Sostenuto (function assignable)
Pedal
Other Function
Connectors
Panel Lock, V-LINK
AC inlet, Pedal connector, Input jacks (L/Mono, R), Output jacks (L/Mono, R), USB connector,
MIDI connectors (In, Out), Phones jack (Stereo) x 2, External Memory connector
Power Consumption
140 W
1410 (W) x 446 (D) x 1070 (H) mm (with top lid close)
55-9/16 (W) x 17-9/16 (D) x 42-1/8 (H) inches
Dimensions (including piano stand)
1410 (W) x 453 (D) x 1124 (H) mm (with top lid open)
55-9/16 (W) x 17-7/8 (D) x 44-1/4 (H) inches
Weight (including piano stand)
Accessories
93.6 kg/206 lbs 6 oz
Owner’s Manual, Power Cord, Roland 60 Classical Piano Masterpieces, Headphones Hook,
Cord Clamps (*1), Stabilizer (*1), Felt (*1)
Options
Headphones, USB Memory, USB Floppy Disk Drive, USB CD Drive
(*1) Supplied with the stand
*
In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
A
G
AC inlet ............................................................................................. 13
Arabic ............................................................................................... 36
Audio Equipment ......................................................................... 66
Audio file ......................................................................................... 73
GS Format ........................................................................................ 80
Hammer Response ................................................................ 35, 79
B
C
Individual ......................................................................................... 28
Input jack ......................................................................................... 13
Cabinet Resonance ............................................................... 35, 79
CD drive ........................................................................................... 60
Composer MIDI Out ............................................................. 54, 68
Computer ........................................................................................ 69
Connecting
Just Major ........................................................................................ 36
Just Minor ........................................................................................ 36
K
Kirnberger ....................................................................................... 36
Count-in ........................................................................................... 24
Lid ......................................................................................... 14, 35, 79
Local Off ........................................................................................... 68
Local On ........................................................................................... 68
Lyrics ................................................................................... 54, 58, 79
D
Delete ............................................................................................... 64
Deleting ........................................................................................... 46
Display .............................................................................................. 12
Dual Play .......................................................................................... 26
Meantone ........................................................................................ 36
MIDI Sound Module ..................................................................... 67
Music Files ....................................................................................... 80
Mute Volume .......................................................................... 54, 56
Muting .............................................................................................. 38
E
Erasing .............................................................................................. 43
F
Factory Reset .......................................................................... 54, 59
File Menu ......................................................................................... 54
Floppy disk drive .......................................................................... 60
Forward button ............................................................................. 12
[Function] button ......................................................................... 12
Function mode ............................................................................. 53
N
Noise ................................................................................................. 35
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Tuning .............................................................................................. 35
Twin Piano ....................................................................................... 27
[Twin Piano] button ..................................................................... 12
O
Output jack ..................................................................................... 13
USB Memory ................................................................................... 60
P
Pair ..................................................................................................... 28
Panel Lock ....................................................................................... 33
Parts .................................................................................................. 38
Pedal cord ....................................................................................... 14
Piano Designer .............................................................................. 34
[Piano Designer] button ............................................................ 12
V-LINK Transmit Channel ........................................................... 70
[Volume] slider .............................................................................. 12
XGlite ................................................................................................. 80
R
Recording ........................................................................................ 41
Reverb ....................................................................................... 25, 79
S
SMF with Lyrics ............................................................................. 80
[Song] (Tempo) button .............................................................. 12
Split Point ................................................................................. 31, 79
T
Tempo ....................................................................................... 22, 40
Tempo Mute ........................................................................... 54, 57
Time Signature .............................................................................. 23
Tone button ................................................................................... 12
Track Assign ..................................................................... 54, 56, 79
Track button ................................................................................... 13
Tracks ................................................................................................ 38
[Transpose] button ...................................................................... 12
Transpose ........................................................................................ 32
84
Download from Www.Somanuals.com. All Manuals Search And Download.
For EU Countries
For China
Download from Www.Somanuals.com. All Manuals Search And Download.
For EU Countries
For the USA
This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
(
)
For C.A. US Proposition 65
WARNING
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
LX-10F
Digital Piano
Roland Corporation U.S.
Address : 5100 S. Eastern Avenue, Los Angeles, CA 90040-2938
Telephone : (323) 890-3700
Download from Www.Somanuals.com. All Manuals Search And Download.
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
Information
PHILIPPINES
CURACAO
URUGUAY
POLAND
JORDAN
AFRICA
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
Zeelandia Music Center Inc.
Orionweg 30
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
ROLAND POLSKA SP. Z O.O.
ul. Kty Grodziskie 16B
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
Curacao, Netherland Antilles
TEL:(305)5926866
03-289 Warszawa, POLAND
TEL: (022) 678 9512
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
EGYPT
TEL: (02) 899 9801
Al Fanny Trading Oꢀce
9, EBN Hagar Al Askalany Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
DOMINICAN REPUBLIC
PORTUGAL
SINGAPORE
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Roland Iberia, S.L.
KUWAIT
VENEZUELA
SWEE LEE MUSIC COMPANY
Branch Oꢀce Porto
Edifício Tower Plaza
Rotunda Eng. Edgar Cardoso
23, 9ºG
4400-676 VILA NOVA DE GAIA
PORTUGAL
EASA HUSAIN AL-YOUSIFI &
Instrumentos Musicales
PTE. LTD.
TEL: (022)-417-1828
SONS CO.
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
Allegro,C.A.
Al-Yousiꢀ Service Center
P.O.Box 126 (Safat) 13002
KUWAIT
REUNION
Av.las industrias edf.Guitar import
#7 zona Industrial de Turumo
Caracas, Venezuela
MARCEL FO-YAM Sarl
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
TEL: 00 965 802929
ECUADOR
TAIWAN
TEL: (212) 244-1122
TEL:(+351) 22 608 00 60
Mas Musika
ROLAND TAIWAN ENTERPRISE
LEBANON
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
ROMANIA
REUNION ISLAND
TEL: (0262) 218-429
CO., LTD.
Chahine S.A.L.
FBS LINES
9F-5, No. 112 Chung Shan
North Road Sec. 2 Taipei 104
TAIWAN R.O.C.
George Zeidan St., Chahine Bldg.,
Achraꢀeh, P.O.Box: 16-5857
Beirut, LEBANON
Piata Libertatii 1,
535500 Gheorgheni, ROMANIA
TEL: (266) 364 609
EUROPE
SOUTH AFRICA
EL SALVADOR
T.O.M.S. Sound & Music (Pty)Ltd.
2 ASTRON ROAD DENVER
JOHANNESBURG ZA 2195,
SOUTH AFRICA
TEL: (02) 2561 3339
TEL: (01) 20-1441
OMNI MUSIC
BELGIUM/FRANCE/
HOLLAND/
75 Avenida Norte y Final Alameda
Juan Pablo II,
Ediꢀcio No.4010 San Salvador,
EL SALVADOR
RUSSIA
THAILAND
OMAN
Roland Music LLC
Theera Music Co. , Ltd.
100-108 Soi Verng Nakornkasem,
New Road,Sumpantawong,
Bangkok 10100 THAILAND
TEL: (02) 224-8821
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
LUXEMBOURG
TEL: (011)417 3400
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: 262-0788
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
GUATEMALA
SERBIA
TEL: (014) 575811
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
Music AP Ltd.
QATAR
Sutjeska br. 5 XS - 24413 Palic,
SERBIA
TEL: (024) 539 395
CROATIA
Al Emadi Co. (Badie Studio
ART-CENTAR
OCEANIA
& Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
Degenova 3.
HR - 10000 Zagreb
TEL: (1) 466 8493
TEL:(502) 599-2888
SLOVAKIA
ASIA
AUSTRALIA/
HONDURAS
DAN Acoustic s.r.o.
Povazská 18.
SAUDI ARABIA
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
NEW ZEALAND
CZECH REP.
aDawliah Universal Electronics
SK - 940 01 Nové Zámky
TEL: (035) 6424 330
Roland Corporation
CZECH REPUBLIC DISTRIBUTOR
APL
CHINA
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
s.r.o
Behind Pizza Inn
Prince Turkey Street
aDawliah Building,
PO BOX 2154,
Alkhobar 31952
SAUDI ARABIA
TEL: (03) 8643601
Roland Shanghai Electronics
Voctárova 247/16
CZ - 180 00 PRAHA 8,
CZECH REP.
SPAIN
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
MARTINIQUE
TEL: (2) 830 20270
Musique & Son
Z.I.Les Mangle
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
DENMARK
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing 100011
CHINA
Roland Scandinavia A/S
SKAGERRAKVEJ 7 POSTBOX 880
DK-2100 OPENHAGEN,
DENMARK
SWEDEN
SYRIA
Roland Scandinavia A/S
Technical Light & Sound Center
PO BOX 13520 BLDG No.17
ABDUL WAHAB KANAWATI.ST
RAWDA DAMASCUS, SYRIA
TEL: (011) 223-5384
SWEDISH SALES OFFICE
Mårbackagatan 31, 4 tr.
SE-123 43 Farsta
Sweden
TEL: (0)8 683 04 30
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 3916 6200
CENTRAL/LATIN
AMERICA
FINLAND
TEL: (010) 6426-5050
Roland Scandinavia As, Filial
TEL: 596 596 715222
HONG KONG
TURKEY
Finland
SWITZERLAND
Tom Lee Music
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
Vanha Nurmijarventie 62
01670 Vantaa
Finland
MEXICO
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen, SWITZERLAND
TEL: (061)975-9987
ARGENTINA
11/F Silvercord Tower 1
30 Canton Rd
Tsimshatsui, Kowloon
Hong Kong
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico D.F.
MEXICO
Instrumentos Musicales S.A.
Av.Santa Fe 2055
TEL: (0)9 68 24 020
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
U.A.E.
GERMANY/AUSTRIA
TEL: 825-2737-7688
UKRAINE
TEL: (55) 5668-6699
Zak Electronics & Musical
Roland Elektronische
EURHYTHMICS Ltd.
P.O.Box: 37-a.
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Ground Floor, Dubai,
U.A.E.
Parsons Music Ltd.
Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt,
GERMANY
NICARAGUA
BARBADOS
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
Bansbach Instrumentos
Nedecey Str. 30
UA - 89600 Mukachevo, UKRAINE
TEL: (03131) 414-40
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (040) 52 60090
TEL: (04) 3360715
GREECE/CYPRUS
UNITED KINGDOM
INDIA
STOLLAS S.A.
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
BRAZIL
Rivera Digitec (India) Pvt. Ltd.
411, Nirman Kendra Mahalaxmi
Flats Compound Oꢀ. Dr. Edwin
Moses Road, Mumbai-400011,
INDIA
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
TEL: (505)277-2557
Roland Brasil Ltda.
NORTH AMERICA
Rua San Jose, 211
PANAMA
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE PANAMA
TEL: 315-0101
UNITED KINGDOM
TEL: (01792) 702701
CANADA
TEL: (022) 2493 9051
HUNGARY
Roland Canada Ltd.
Roland East Europe Ltd.
2045 Torokbalint, FSD Park,
building 3.
CHILE
(Head Oꢀce)
INDONESIA
Comercial Fancy II S.A.
Rut.: 96.919.420-1
5480 Parkwood Way Richmond B.
C., V6V 2M4 CANADA
TEL: (604) 270 6626
PT Citra Intirama
Jl. Cideng Timur No. 15J-15O
Jakarta Pusat
PARAGUAY
MIDDLE EAST
TEL: (23) 511011
Distribuidora De Instrumentos
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
Musicales
INDONESIA
TEL: (021) 6324170
IRELAND
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (595) 21 492147
Roland Canada Ltd.
(Toronto Oꢀce)
170 Admiral Boulevard
Mississauga On L5T 2N6 CANADA
TEL: (905) 362 9707
BAHRAIN
Roland Ireland
Moon Stores
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
COLOMBIA
KOREA
No.1231&1249 Rumaytha
Building Road 3931, Manama 339
BAHRAIN
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
PERU
Audionet
TEL: 17 813 942
Distribuciones Musicales SAC
Juan Fanning 530
Miraꢀores
Lima - Peru
TEL: (511) 4461388
TEL: (574)3812529
U. S. A.
ITALY
IRAN
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
COSTA RICA
MALAYSIA
MOCO INC.
JUAN Bansbach Instrumentos
Roland Asia Paciꢀc Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
Musicales
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
TEL: (323) 890 3700
TRINIDAD
NORWAY
TEL: (021)-2285-4169
AMR Ltd
Roland Scandinavia Avd.
Ground Floor
ISRAEL
Kontor Norge
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868) 638 6385
VIET NAM
Halilit P. Greenspoon & Sons
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
VIET THUONG CORPORATION
386 CACH MANG THANG TAM ST.
DIST.3,
Ltd.
8 Retzif Ha'alia Hashnia St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
TEL: 2273 0074
HO CHI MINH CITY
VIET NAM
TEL: (08) 9316540
As of Jan. 1,2010 (ROLAND)
Download from Www.Somanuals.com. All Manuals Search And Download.
*
5
1
0
0
0
1
3
6
1
9
-
0
1
*
Download from Www.Somanuals.com. All Manuals Search And Download.
|