Download from Www.Somanuals.com. All Manuals Search And Download.
201b
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY
INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY” (p. 3), and “IMPORTANT NOTES”
(p. 6). These sections provide important information concerning the proper operation of
the unit. Additionally, in order to feel assured that you have gained a good grasp of
every feature provided by your new unit, Owner’s manual should be read in its entirety.
The manual should be saved and kept on hand as a convenient reference.
202
Copyright © 2008 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any
form without the written permission of ROLAND CORPORATION.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
product’s enclosure that may be of sufficient magnitude to
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
The exclamation point within an equilateral triangle is
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
7. Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE: NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions or
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle.
In the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
The
symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
The
symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
Do not disassemble or modify
Use only the included power cord
002a
008e
Do not disassemble or modify this device.
You must use only the power cord included with the
device. Do not use the included power cord with
any other device.
......................................................................................
......................................................................................
Do not repair or replace parts
Do not bend the power cord or place heavy objects
on it
003 Never attempt to repair this device or replace
parts. If repair or part replacement should become
necessary, you must contact your dealer or a
Roland service center.
009 Do not bend the power cord excessively, or place
heavy objects on the power cord. Doing so will
damage the power cord, and may cause short
circuits or faulty connections, possibly resulting in
fire or electrical shock.
......................................................................................
Do not use or store in the following types of
locations
......................................................................................
004
Do not share an outlet with an unreasonable
number of other devices
• Locations of extremely high temperature (such as
in direct sunlight, near heating equipment, or on
a device that generates heat)
• Near moisture (such as in a bathroom, near a
sink, or on a wet floor) or in locations of high
humidity
015 Do not connect excessive numbers of electrical
devices to a single power outlet. In particular,
when using a power strip, exceeding the rated
capacity (watts/amps) of the power strip may
cause heat to be generated, possibly melting the
cable.
• Locations exposed to rain
• Locations of excessive dust
......................................................................................
Avoid extended use at high volume
• Locations subject to heavy vibration
......................................................................................
010 This device, either by itself or used in conjunction
with headphones, amps, and/or speakers, is
capable of producing volume levels that can cause
permanent hearing damage. If you experience
impaired hearing or ringing in your ears, immedi-
ately stop using the device and consult a medical
specialist.
Do not place in an unstable location
007 Do not place this device on an unstable stand or a
tilted surface. You must place it in a stable and
level location.
......................................................................................
Connect the power cord to an outlet of the correct
voltage
......................................................................................
008a
Do not insert foreign objects
You must connect the power cord to an AC outlet
of the correct voltage as marked on the device.
011 Never allow foreign objects (flammable objects,
coins, wires, etc.) to enter this device.
......................................................................................
This can cause short circuits or other malfunctions.
......................................................................................
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
Turn off the power if an abnormality or
malfunction occurs
Place in a well ventilated location
101a
When using this device, ensure that it is placed in
a well ventilated location.
012a
If any of the following should occur, immediately
turn off the power, disconnect the power cord from
the AC outlet, and contact your dealer or a service
center to have the device serviced.
..........................................................................................................
Grasp the plug when connecting or disconnecting
the power cord
• The power cord is damaged
102b
• The device produces smoke or an unusual smell
• A foreign object enters the device, or liquid
spills into the device
When connecting or disconnecting the power cord
to/from an AC outlet or the device itself, you must
grasp the plug, not the cord.
• The device becomes wet (by rain, etc.)
• An abnormality or malfunction occurs in the device
......................................................................................
..........................................................................................................
Periodically wipe the dust off the power cord plug
103a
Do not allow children to use without supervision
From time to time, you should unplug the power
013 In households with children, take particular care
against tampering. If children are to use this device,
they must be supervised or guided by an adult.
cord from the AC outlet and use a dry cloth to wipe
the dust off of it. You should also unplug the power
cord from the AC outlet if you will not be using the
device for an extended period of time. Dust or dirt
that accumulates between the power cord plug and
the AC outlet can cause a short circuit, possibly
resulting in fire.
......................................................................................
Do not drop or subject to strong impact
014 Do not drop this device or subject it to strong
impact.
..........................................................................................................
Manage cables for safety
......................................................................................
104 Ensure that the connected cables are organized
and managed in a safe manner. In particular,
place the cables out of reach of children.
Do not use overseas
016 If you wish to use this device overseas, please
contact your dealer or a service center.
..........................................................................................................
Do not stand or place heavy objects on this device
......................................................................................
Do not use a CD-ROM in an audio CD player or
106 Do not stand on this device, or place heavy objects
on it.
DVD player
023 If you attempt to play back a CD-ROM in a conven-
tional audio CD player or DVD player, the resulting
high volume may damage your hearing or your
speakers.
..........................................................................................................
Do not connect or disconnect the power cord with
wet hands
107b
Do not connect or disconnect the power cord to the
device or AC outlet while holding the power cord
plug with wet hands.
......................................................................................
Do not place containers of water on the device
026 Do not place containers of water (such as a flower
vase) or drinks on the device. Nor should you
place containers of insecticide, perfume, alcoholic
liquids, nail polish, or spray cans on the device.
Liquids that spill into the device may cause it to
malfunction, and may cause short circuits or faulty
operation.
..........................................................................................................
Cautions when moving this device
108d
If you need to move the instrument, take note of the
precautions listed below. Since this product is very
heavy, you must make sure that a sufficient number
of people are on hand to help, so you can lift and
move it safely, without causing strain. It should be
handled carefully, all the while keeping it level.
Make sure to have a firm grip, to protect yourself
from injury and the instrument from damage.
......................................................................................
1
• Check whether the knob bolts fastening the
device to its stand have become loose. If they
are loose, tighten them firmly.
• Disconnect the power cord.
• Disconnect external devices.
• Close the lid (Only for AT-300).
2
3
5
6
• Remove the music stand.
..........................................................................................................
4
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE UNIT SAFELY
Unplug the power cord from the AC outlet before
cleaning
109a
Before you clean the device, turn off the power and
unplug the power cord from the AC outlet.
..........................................................................................................
If there is a possibility of lightning strike,
disconnect the power cord from the AC outlet
110a
ately turn off the power and disconnect the power
cord from the AC outlet.
..........................................................................................................
(For AT-300)
Cautions when opening/closing the lid
116 Be careful when opening/closing the lid so you do
not get your fingers pinched (p. 16). Adult super-
vision is recommended whenever small children
use the unit.
..........................................................................................................
Cautions when using the seat
117:YSoeluecmtiounst observe the following cautions when
using the seat.
1
• Do not play with the seat or use it as a stepstool.
• Do not allow two or more people to sit on the
seat simultaneously.
2
4
• Do not sit on the seat if the bolts fastening the
legs are loose. (If they are loose, use the
included tool to retighten them.)
..........................................................................................................
Keep small items out of the reach of children
118cTo prevent small items such as the following from
being swallowed accidentally, keep them out of the
reach of children.
• Removed parts
• Cord hook
• Wing nut for cord hook
• Screws for assembling the stand
• Knob bolts
• Cord clamps
..........................................................................................................
Do not remove the speaker grille and speaker
121 Do not remove the speaker grille and speaker by
any means. Speaker not user replaceable. Shock
hazardous voltages and currents are present inside
the enclosure.
..........................................................................................................
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notes
Power Supply
Care
301
• Do not connect this device to the same electrical outlet as an
4•01b For everyday care, wipe with a soft dry cloth, or remove
stubborn dirt using a tightly wrung-out cloth. If this device
contains wooden components, wipe the entire area following
the direction of the grain. The finish may be damaged if you
inverter-controlled device such as a refrigerator, microwave
oven, or air conditioner, or a device that contains an electric
motor. Depending on how the other device is used, power
supply noise could cause this device to malfunction or produce
noise. If it is not practical to use a separate electrical outlet,
continue strongly rubbing a single location.
Addition
• If water droplets should adhere to this device, immediately
please connect this device via a power supply noise filter.
wipe them off using a soft dry cloth.
307
402
• Before you make connections, you must switch off the power
• Do not use solvents such as benzene, thinner, or alcohol, since
on all devices to prevent malfunction and/or speaker damage.
these can cause deformation or color change.
308
• Although the LCD and LEDs are switched off when the Power
switch is switched off, this does not mean that the unit has been
completely disconnected from the source of power. If you need
to turn off the power completely, first turn off the Power switch,
then unplug the power cord from the power outlet. For this
reason, the outlet into which you choose to connect the power
cord’s plug should be one that is within easy reach and readily
accessible.
Servicing
452
• If you return this device for servicing, the contents of memory
may be lost. Please store important contents on USB memory,
or make a note of the contents. We take utmost care to
preserve the contents of memory when performing service, but
there may be cases when the stored content cannot be
recovered because the memory section has malfunctioned.
Please be aware that we cannot accept responsibility for the
recovery of lost memory content or for any consequences of
such loss.
Location
351
• If this device is placed near devices that contain large
transformers, such as power amps, hum may be induced in
this device. If this occurs, move this device farther away or
change its orientation.
Other Cautions
551
• Stored content may be lost due to a malfunction of the device
3•52a If this device is operated near a television or radio, color
distortion may be seen in the television screen or noise may be
heard from the radio. If this occurs, move this device farther
away.
or because of inadvertent operation. You should back up
important content on USB memory as a safeguard against
such loss.
552
• We cannot accept responsibility for the recovery of any
3•52b Keep your cell phone powered off or at a sufficient distance
from this device. If a cell phone is nearby, noise may be heard
when a call is received or initiated, or during conversation.
content lost from internal memory or USB memory, or for the
consequences of such loss.
553
• Do not apply excessive force to the buttons, knobs, or input/
3•54b Do not leave this device in direct sunlight, near devices that
produce heat, or in a closed-up automobile. Do not allow
illumination devices operated in close proximity (such as a
piano light) or powerful spotlights to shine on the same
location on this device for an extended time. This can cause
deformation or color change.
output jacks, since this may cause malfunctions.
554
• Never strike or apply strong pressure to the display.
556
• When connecting or disconnecting cables, grasp the plug (not
the cable) to prevent short circuits or broken connections.
557
• This device may produce a certain amount of heat, but this is
3•55b If you move this device between locations of radically different
temperature or humidity, water droplets (condensation) may
form inside the device. Using the device in this condition will
cause malfunctions, so please allow several hours for the
not a malfunction.
5•58a Please enjoy your music in ways that do not inconvenience
other people nearby, and pay particular attention to the
volume at nighttime. Using headphones will allow you to enjoy
music without having to be concerned about others.
condensation to disappear before you use the device.
356
5•59b When transporting or shipping this device, package it in an
appropriate amount of cushioning material. Scratches,
damage, or malfunctions may occur if you transport it without
• Do not allow items made of rubber or vinyl to remain on top of
this device for an extended time. This can cause deformation
or color change.
358
appropriate packaging.
• Do not leave objects on top of the keyboard or pedalboard.
560
This can cause malfunctions such as failure to sound.
• If using the music rest, do not apply excessive force to it.
359
562
• Do not affix adhesive labels to this device. The exterior finish
• Some connection cables contain a resistor. Do not connect
may be damaged when you remove the labels.
such cables to this device. Doing so may make the volume
extremely low or inaudible. Please use connection cables not
containing a resistor.
360
• Depending on the material and temperature of the surface on
which you place the unit, its rubber feet may discolor or mar
the surface.You can place a piece of felt or cloth under the
rubber feet to prevent this from happening. If you do so,
please make sure that the unit will not slip or move
accidentally.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notes
Addition
Floppy Disk Handling
• Do not insert anything other than USB memory (e.g., wire,
coins, other types of device) into the external memory
connector. Doing so will damage the external memory
(Using Optional Floppy Disk Drive)
651
• Floppy disks contain a plastic disk with a thin coating of
connector.
magnetic storage medium. Microscopic precision is required
to enable storage of large amounts of data on such a small
surface area. To preserve their integrity, please observe the
following when handling floppy disks:
Addition
• Do not apply excessive force to the connected USB memory.
Addition
• If you will not be using USB memory for an extended period of
time, close the USB memory cover.
• Never touch the magnetic medium inside the disk.
• Do not use or store floppy disks in dirty or dusty areas.
• Do not subject floppy disks to temperature extremes
(e.g., direct sunlight in an enclosed vehicle).
Handling the CDs (CD-ROMs)
(Using Optional CD Drive)
Add
Recommended temperature range: 10–50 degrees C
(50–122 degrees F).
• Do not expose floppy disks to strong magnetic fields,
such as those generated by loudspeakers.
• When handling the discs, please observe the following.
• Do not touch the encoded surface of the disc.
• Do not use in dusty areas.
• Do not leave the disc in direct sunlight or an enclosed
vehicle.(Storage temperature: 0–50 degrees C)
652
• Floppy disks have a “write protect” tab which can protect the
801
disk from accidental erasure. It is recommended that the tab
be kept in the PROTECT position, and moved to the WRITE
• Avoid touching or scratching the shiny underside (encoded
surface) of the disc. Damaged or dirty CD-ROM discs may not
be read properly. Keep your discs clean using a commercially
position only when you wish to write new data onto the disk.
fig.DiskProtect.e.eps
available CD cleaner.
Add
Rear side of the disk
• Keep the disc in the case.
Add
• Do not keep the disc in the CD drive for a long time.
Add
Write
• Do not put a sticker on the label of the disc.
(can write new data onto disk)
Add
• Wipe the disc with a soft and dry cloth radially from inside to
Protect
outside. Do not wipe along circumference.
Write Protect Tab
(prevents writing to disk)
Add
• Do not use benzine, record cleaner spray or solvents of any
653
kind.
• The identification label should be firmly affixed to the disk.
Add
Should the label come loose while the disk is in the drive, it
• Do not bend the disc. Bending discs may prevent proper
may be difficult to remove the disk.
reading and writing of data, and may further result in
malfunction.
654
• Store all disks in a safe place to avoid damaging them, and to
protect them from dust, dirt, and other hazards. By using a
dirty or dust-ridden disk, you risk damaging the disk, as well
as causing the disk drive to malfunction.
Copyright
852
• This product can be used to record or duplicate audio or
visual material without being limited by certain technological
copy-protection measures. This is due to the fact that this
product is intended to be used for the purpose of producing
original music or video material, and is therefore designed so
that material that does not infringe copyrights belonging to
others (for example, your own original works) can be
USB Memory Handling
(Using Optional USB Memory)
704
• When connecting USB memory, firmly insert it all the way in.
705
• Do not touch the pins of the USB memory connector, or allow
them to become dirty.
recorded or duplicated freely.
708
853
• USB memory is made using high-precision electronic
• Do not use this unit for purposes that could infringe on a
components, so please observe the following points when
handling it.
copyright held by a third party. We assume no responsibility
whatsoever with regard to any infringements of third-party
copyrights arising through your use of this unit.
• To prevent damage from static electrical charges,
discharge any static electricity that might be present in
your body before handling USB memory.
• Do not touch the terminals with your fingers or any metal
object.
• Do not bend or drop USB memory, or subject it to strong
impact.
• Do not leave USB memory in direct sunlight or in
locations such as a closed-up automobile. (Storage
temperature: 0–50 degrees C)
203
* GS (
) is a registered trademark of Roland
) is a registered trademark of Yamaha
Corporation.
Add
* XGlite (
Corporation.
220
* All product names mentioned in this document are
trademarks or registered trademarks of their
respective owners.
• Do not allow USB memory to become wet.
• Do not disassemble or modify USB memory.
Addition
• When connecting USB memory, position it horizontally with
the external memory connector and insert it without using
excessive force. The external memory connector may be
damaged if you use excessive force when inserting USB
memory.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Features
We want to take a moment to thank you for your purchase of the Roland Organ “Music ATELIER AT-100/300.” The
ATELIER is an electronic organ which provides a generous collection of rich organ sounds. In addition, it is designed
to be easy to learn and use. In order to enjoy reliable performance of your new keyboard for many years to come,
please take the time to read through this manual in its entirety.
* The AT-100 and AT-300 are abbreviated in this manual as “ATELIER” respectively.
Basic Concepts of the ATELIER Series
A full complement of organ sounds
A wide range of basic organ sounds, ranging from jazz organ and pipe organ to theatre organ, are onboard so you
are sure to enjoy having access to all the sounds you expect from an organ.
Panel layout based on a tradition of emphasis on realtime operation
Based on the idea that you should be able to sit down and begin playing immediately, the operation buttons of the
panel are arranged by function as dictated by classic organ traditions, ensuring easy and intuitive operation. All
models of the ATELIER series feature the same operability, allowing you to start playing immediately even if you switch
models.
High-quality sounds that you can use without editing
In addition to a full range of organ sounds, high-quality sounds such as strings and brass are also included onboard.
You can simply select sounds and enjoy playing the organ—no need to perform complicated editing operations.
Expansive lower keyboard with damper pedal for piano-like expressiveness
The piano is indispensable to contemporary music performance. All models of the ATELIER series contain high-quality
grand piano sounds that you will enjoy performing. In addition, the range of the lower keyboard has been expanded,
giving you greater expressive capabilities on the piano. A damper pedal and initial touch sensitivity are also
provided, both necessities for piano performance.
Design utilizes your existing music data
The ATELIER series is designed so that even on new models, you will feel right at home and can begin playing
immediately. Consideration has been given to data compatibility, and existing song data or registration data can be
moved to USB memory or used by connecting a floppy disk drive.
Music styles from around the world
A rich variety of the world’s most representative music styles (rhythm and auto accompaniment patterns) are built-in,
allowing you to more readily perform music from almost any genre.
Utilizes SMF music files
Compatible with General MIDI 2, the world standard in SMF music files. Since an external memory connector is
provided, you can connect separately available USB memory or a floppy disk drive and take advantage of the wide
range of commercially available SMF music files. You can also mute parts, allowing you to practice the part for each
hand separately, and enjoy performing ensemble with the music files.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Features
Features
Harmonic bars for creating organ sounds
The organ is equipped with “Harmonic bars,” which are much like the controllers used on traditional jazz organs. By
operating the harmonic bars, you can easily create a diverse variety of organ sounds.
USB Memory
You can connect separately sold USB memory or a floppy disk drive, and play back SMF music files.
Performances you record or registration data you create can also be saved on USB memory or a floppy disk, or you
can save SMF music files or registrations from USB memory or a floppy disk into internal user memory.
Highly realistic rhythms and automatic accompaniment functions
All rhythms use data from performances by professional drummers, featuring high-quality patterns with all the grooves
and subtle nuance of the real thing. In addition, you can use automatic accompaniments that are perfectly matched to
each rhythm to enjoy the feeling of playing with your own band in the background.
Human Voices
In addition to a full complement of organ tones, the ATELER also features tones that express a wide range of human
vocal qualities, including “Jazz Scat,” which changes according to how firmly the keys are pressed, and “Classical”
tones that perfectly express that choir image.
Active Expression sounds
For some of the sounds, moving the expression pedal will vary not only the volume but also the tone, or add other
sounds. From pianissimo to fortissimo, the tonal character of the sound itself will change as you perform a crescendo,
or strings may appear behind the piano, creating dynamic changes in tonality.
Harmony Intelligence
The Harmony Intelligence function automatically adds harmony to the upper keyboard sound according to the chord
you play in the lower keyboard. This gives you greater tonal depth and a more powerful performance.
Split Function
The 61-key lower manual can be split into separate sections, with each being used to play a different tone. Using the
Split function lets you perform with the richness of performance expression rivalling that of three-manual and even four-
manual instruments.
Conventions Used in This Manual
This manual uses the following conventions in the interest of simpler, more concise instructions.
• The AT-100 and AT-300 are abbreviated in this manual as “ATELIER” respectively.
• In this manual, an illustration of the AT-300 is sometimes used for explanatory purposes.
985
• The explanations in this manual include illustrations that depict what should typically be shown by the display.
Note, however, that your ATELIER may incorporate a newer, enhanced version of the system (e.g., includes
newer sounds), so what you actually see in the display may not always match what appears in the manual.
• Button names are enclosed in square brackets (“[ ]”), as in [Drums/SFX] button.
• [▲] [▼], [
] [
] means that you should press one or the other button.
Example: Reverb [▲] [▼] buttons, Tempo [
] [
] buttons.
NOTE
• An asterisk (*) or a
be ignored.
at the beginning of a paragraph indicates a note or precaution. These should not
• (p. **) refers to pages within the manual.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions Used in This Manual...............................................................................9
Setting Up the Music Rest..................................................................................................16
Connecting the Speaker Cord (AT-300)..............................................................................16
Opening/Closing the Lid (AT-300).....................................................................................16
Connecting the Power Cord ..............................................................................................17
Turning the Power On and Off ..........................................................................................17
Turning On the Power .............................................................................................17
Turning Off the Power.............................................................................................18
Using Headphones ..........................................................................................................18
Using the Cord Hook .......................................................................................................19
Restoring All the Factory Default Settings (Factory Reset) .......................................................19
Adjusting the Contrast of the Screen...................................................................................20
Using the External Memory ...............................................................................................20
Connecting the USB Memory ...................................................................................20
Connecting the Floppy Disk Drive (Sold Separately)....................................................21
Using a CD.....................................................................................................................22
Connecting a CD Drive (Sold Separately)..................................................................22
About the Adjuster...........................................................................................................22
About the Display................................................................................ 23
Understanding the Main and Related Screens ............................................................23
Listening to the Demo Songs..............................................................................................24
Selecting Voices ..............................................................................................................26
About the Voices and Parts......................................................................................26
Selecting the Upper/Lower/Pedal Bass Voices...........................................................27
Selecting Solo Voice ...............................................................................................28
Selecting a Voice Using the [Others] Button ...............................................................29
Creating Organ Sounds (Vintage Organ) ...........................................................................30
Playing a Vintage Organ Voice................................................................................32
Performing with an Active Expression Voice........................................................................35
Adjust the Volume Balance................................................................................................36
Transpose the Pitch in Octave Units (Octave Shift)................................................................37
Sustaining Notes Played on the Lower Keyboard .................................................................38
Playing Drums from the Entire Lower Keyboard (Drums/SFX).................................................38
Changing the Drum/SFX Set....................................................................................39
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting a Rhythm...........................................................................................................40
Using Rhythms Stored in User Memory......................................................................41
Playing Rhythm................................................................................................................42
Starting at the Press of a Button ................................................................................42
the Lower Keyboard or Pedalboard (Synchro Start).....................................................43
Stopping the Rhythm ...............................................................................................44
Changing a Tempo of Rhythm and Automatic Accompaniment..............................................45
Playing a Countdown Sound When the Intro Ends ...............................................................45
Playing Rhythm and Automatic Accompaniment...................................................................46
Adding Variety to the Rhythm or Automatic Accompaniment .................................................47
Turning Chord Intelligence On/Off ....................................................................................48
Using the Leading Bass Function........................................................................................49
Using a Rhythm from a USB Memory..................................................................................51
Reviewing the Styles on USB Memory .......................................................................51
Copying Rhythms.............................................................................................................52
Deleting Saved Rhythm.....................................................................................................54
Storing Registrations.........................................................................................................56
Recalling a Registration ....................................................................................................57
How to Recall a Registration ....................................................................................57
Changing the Timing of Recalling Registrations ..........................................................57
Automatically Registering When You Switch Panel Settings...................................................58
Assigning a Name to a Registration Set..............................................................................58
Saving Registration Sets....................................................................................................60
Loading Previously Saved Registration Sets Into the ATELIER..................................................62
Loading a Set of Registrations ..................................................................................62
Loading an Individual Registration............................................................................63
Deleting a Set of Registrations ...........................................................................................64
Copying Registrations ......................................................................................................65
Using the Performance Functions.......................................................... 67
Transposing to a Different Key (Key Transpose) ...................................................................67
Adding Decay to the Sound (Damper Pedal) .......................................................................68
Using the Foot Switch.......................................................................................................68
Changing the Function of the Foot Switch ..................................................................69
Using the Foot Switch to Switch Registrations (Registration Shift)...................................70
Adjusting the Overall Volume Using an Expression Pedal......................................................71
Adding Harmony to a Melody (Harmony Intelligence)..........................................................72
Changing the Type of Harmony Intelligence...............................................................73
Adding Modulation to the Sound (Rotary Effect)...................................................................74
Sustain Effect...................................................................................................................75
Changing the Sustain Length....................................................................................76
Reverb Effect...................................................................................................................77
Changing the Reverb Type.......................................................................................78
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Changing the Wall Type .........................................................................................79
Changing the Depth of the Reverb............................................................................80
Making Effective Use of the Lower Keyboard.......................................................................82
Playing the Solo Voice on the Lower Keyboard (Solo [To Lower] Button) .................................84
Changing the Solo Split Point...................................................................................85
Using the Lower Keyboard to Play the Bass Voice (Bass Split)................................................86
Changing the Bass Split Point...................................................................................87
Using the Lower Keyboard to Play the Bass Voice (Pedal [To Lower] button)............................88
What is a Track Button? ..........................................................................................89
Silencing a Specific Track (Track Mute) ..............................................................................91
Recording a Performance..................................................................................................91
Playing Back a Performance Song .....................................................................................92
Add a Count Sound to Match the Timing (Count In)..............................................................93
Recording Each Part Separately.........................................................................................93
Re-Recording...................................................................................................................94
Erasing a Performance Song .............................................................................................94
Changing the Name of a Performance Song (Rename).........................................................95
Saving Performance Songs ...............................................................................................96
Loading Performance Songs Into the ATELIER.......................................................................97
Deleting Performance Songs Stored on “Favorites” or the USB Memory..................................98
Layering a New Recording onto SMF Music Files ................................................................99
Using Song with a Different Tempo Than That of the Performance Song................................100
Copying Performance Song ............................................................................................101
Creating a Folder in USB Memory or User Memory ...........................................................102
Changing the Name of a Folder......................................................................................102
Enjoying VIMA TUNES Songs .........................................................................................103
Listening to a VIMA TUNES Song ...........................................................................103
Listening to Songs from Music CD....................................................................................104
Enjoying Karaoke with a Music CD (Center Cancel) .................................................104
Transposing the Song to a Comfortable Key for Singing............................................105
Adjusting How the Instrument Responds............................................................................106
Adjusting the Initial Touch Sensitivity (Initial Touch) ...................................................106
Performance Function Settings .........................................................................................107
Changing the Function of the Expression Pedal (Exp. Source).....................................107
Rhythm Settings .............................................................................................................108
Preventing Rhythm Tempos from Switching Automatically (Auto Std Tempo) .................108
Changing the Sound of the Countdown (Count Down Sound).....................................108
Registration Settings.......................................................................................................109
Registration Arranger Update (Arranger Update)......................................................109
Registration Transpose Update (Trans. Update) ........................................................109
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Composer Settings.........................................................................................................110
Switching the Display of Lyrics On or Off (Lyric) .......................................................110
Changing the Metronome Setting (Metronome) .......................................................111
Setting the Beat (Beat)...........................................................................................112
Silencing a Specific Track (Track Mute) ...................................................................113
Other Settings ...............................................................................................................114
Adjust the Standard Pitch (Master Tune)...................................................................114
Setting PC Numbers (PC Number) ..........................................................................115
MIDI IN Mode (MIDI IN Mode) ..............................................................................116
Selecting the MIDI Transmit Channel (Tx MIDI Channel).............................................117
Using the V-LINK function (V-LINK) ..........................................................................117
(Panel Reset) .................................................................................................................119
Formatting a USB Memory (Format)..................................................................................120
Names and Functions of Jacks and Connectors .................................................................121
Connecting Audio Equipment..........................................................................................121
Making the Connections........................................................................................121
Connecting a Computer..................................................................................................122
Making the Settings for the USB Driver....................................................................123
Connecting MIDI Devices................................................................................................123
Making the Connections........................................................................................124
Troubleshooting.............................................................................................................125
Error Message...............................................................................................................129
Chord List .....................................................................................................................130
Glossary.......................................................................................................................132
Music Files That the ATELIER Can Use...............................................................................133
The ATELIER Allows You To Use the Following Music Files..........................................133
About the ATELIER Sound Generator.......................................................................133
Settings That Are Stored After the Power Is Turned Off........................................................134
Settings That Are Stored After the Power Is Turned Off ..............................................134
Settings That Are Stored In the Registration Buttons ...................................................134
Settings That Are Stored In the Individual Registration Buttons.....................................134
MIDI Implementation Chart .............................................................................................135
Main Specifications .......................................................................................................136
Demo Song List..............................................................................................................138
Profile .................................................................................................................138
Index............................................................................................................................139
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Descriptions
3
4
5
6
7
8
9
10
11
12
13
19
20
14
15
16
1718
21
1. [Power On] switch ( → p. 17)
2. [Master Volume] knob ( → p. 18)
3. Harmonic Bars ( → p. 30)
8. [One Touch Program] button ( → p. 50)
9. [Harmony Intelligence] button( →p. 72 )
11. Vintage Organ buttons ( →p. 30)
12. Lower [Drums/SFX] button ( → p. 38)
13. [Load] button ( → p. 62, p. 94, p. 99)
14. Transpose [-] [+] buttons ( → p. 67)
4. Pedal Bass Voice Select buttons ( → p. 27)
Pedal Part
[To Lower] button ( → p. 88)
Level [▲] [▼] button ( → p. 36)
5. Lower Voice Select buttons ( → p. 27)
Lower part
Level [▲] [▼] button ( → p. 36)
6. Upper Voice Select buttons ( → p. 27)
15.
[Utility] button ( → p. 106)
[Display/Exit] button ( → p. 23)
Upper part
Level [▲] [▼] button ( → p. 36)
Menu [
][
] buttons
Value [-] [+] buttons
7. Solo Voice Select buttons ( → p. 28)
Solo part
[To Lower] button ( → p. 84)
Level [▲] [▼] button ( → p. 36)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Descriptions
2
1
Write
Manual
1
2
3
4
5
6
7
8
22
16. Display ( → p. 23)
20. Rhythm Select buttons ( → p. 40)
Rhythm button
17. [Save] button ( → p. 60, p. 96)
18. Beat Indicator ( → p. 45)
19. Composer ( → p. 89)
Tempo [
][
] button ( → p. 45)
Arranger [On/Off] button ( → p. 46)
Auto[Fill in] button ( → p. 47)
Variation [1]–[4]buttons ( → p. 47)
[Intro/Ending] button ( → p. 42)
[Start/Stop] button ( → p. 44)
[Song] button
[Registration] button
[Media] button
Track buttons
21. Rotary Sound buttons ( → p. 74)
[On/Off] button
[Bass] button
[Lower] button
[Solo/Upper] button
[Fast/Slow] button
22. Registration buttons
[Write] button ( → p. 56)
[Reset] button
[Play/Stop] button
[Rec] button
[Bwd] button
[Fwd] button
[Manual] button ( → p. 58)
Registration [1]–[8] buttons ( → p. 55)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start Playing
Opening/Closing the Lid
(AT-300)
Setting Up the Music Rest
fig.01-03
fig.00-22.eps
1. To open the lid, hold it with both hands and
1. Attach the music rest by inserting it into the
slide it to the rear.
two holes.
2. To close the lid, slowly pull it forward until it
Connecting the Speaker Cord
(AT-300)
stops
Be careful not to get your fingers caught when opening or
closing the lid. Adult supervision is recommended when
small children are going to be using the instrument.
NOTE
1. Connect the speaker box’s speaker cord to the
speaker cord leading from the organ.
To prevent accidents, be sure to close the lid before moving
the organ.
NOTE
NOTE
Pay attention to the shape of the speaker cable’s
connector, and insert it until you hear it click securely
into place.
Make sure you don’t have anything (such as sheet music) on
the keyboard when you close the lid.
Organ side
Speaker
box side
Speaker Cord
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start Playing
Connecting the Power Cord
Turning the Power On and Off
941
1. First, make sure that the [Power On] switch is
Once the connections have been completed, turn on or off
power to your various devices in the order specified. By
OFF (not pushed in).
fig. 00-27.eps,fig.00-27-2.eps
turning on or off devices in the wrong order, you risk
causing malfunction and/or damage to speakers and other
devices.
NOTE
Upper position
OFF
Turning On the Power
1. Make sure of the following before the power is
turned on.
• Is the power cord correctly connected to the AC inlet?
• Is the power cord correctly connected to the AC outlet?
• Is the [Master Volume] knob set to the Min (minimum)
2. Connect the supplied power cord to the AC
Inlet, then plug the other end into an AC outlet.
position?
fig.00-26.eps
AT-300
AC Outlet
2. Press the [Power On] switch to turn on the
power.
fig. 00-27.eps, fig.00-27-3.eps
Power Cord
Lower position
AT-100
ON
The main screen will appear in the display.
AC Outlet
Power Cord
Only use the power cord supplied with this instrument.
942
NOTE
The ATELIER is equipped with a protection circuit. A brief
Whenever you do not intend to use the instrument for
extended periods of time, pull out the power cord from the
AC outlet.
NOTE
interval (a few seconds) after power up is required before
the ATELIER will operate normally.
NOTE
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start Playing
3. Adjust the volume to an appropriate level by
moving the [Master Volume] knob or
operating the expression pedal.
Using Headphones
The ATELIER features Phones jacks. These allow you to play
without having to worry about bothering others around you,
Turning the [Master Volume] knob towards “Max”
increases the volume; turning the knob towards “Min”
decreases the volume. Likewise, pressing down on the
expression pedal increases the volume, while easing up
even at night.
fig.00-29.eps
on the pedal decreases the volume.
fig.00-28.eps
decrease
the volume
decrease
the volume
increase
the volume
increase
the volume
Turning Off the Power
1. Before switching the power off, set the [Master
1. Connect your headphones to the Phones jack
underneath the left side of the keyboard.
The sound from the built-in speakers stops.
Volume] knob to the Min (minimum) position.
2. Press the [Power On] switch to turn off the
Now, sound is heard only through the headphones.
fig.00-30.eps
power.
fig. 00-27.eps,fig.00-27-2.eps
2. Adjust the headphones volume with the
[Master Volume] knob and Expression pedal.
945
Some Notes on Using Headphones
If you need to turn off the power completely, first turn off the
[Power On] switch, then unplug the power cord from the
power outlet. Refer to “Power Supply” (p. 6).
NOTE
• To prevent damage to the cord, handle the headphones
only by the headset or the plug.
• Headphones may be damaged if the volume is too high
when they are plugged in. Lower the volume on the
ATELIER before plugging in headphones.
• To prevent possible auditory damage, loss of hearing, or
damage to the headphones, the headphones should not
be used at an excessively high volume. Use the
headphones at a moderate volume level.
• Accepts connection of Stereo headphones.
• If plugs of the headphones are plugged into the Phones
jack, no sound will be heard from the ATELIER’s
speakers.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start Playing
I
Using the Cord Hook
Restoring All the Factory
Default Settings (Factory Reset)
If you’re using headphones, you can use the cord hook to
neatly bundle the cables near your feet.
The settings stored in the ATELIER can be returned to their
factory settings. This function is called “Factory Reset.”
Attaching the Cord Hook
1. Turn down the volume to the minimum level,
1. Screw the cord hook (with wing nut) about
80% of the way into the screw hole located at
the bottom left of the ATELIER.
then turn off the power.
2. While holding down the [One Touch Program]
button, press the [Power On] switch to turn the
2. After you’ve oriented the hook as desired, use
power on.
fig.01-15
the wing nut to fasten it.
Screwhole
Do not turn off the power while the following screen is
displayed.
NOTE
fig.01-16
Wing Nut
Code hook
When factory reset is completed, the basic screen
reappears.
their original factory conditions, refer to “Panel Reset“ (p.
NOTE
119).
Loading factory default settings will erase any Registrations
currently in the memory of the ATELIER. It is a good idea to
save important Registrations to USB memory. To save the
NOTE
registrations you are currently using, refer to “Saving
Registration Sets” (p. 60).
To return only the User memory settings to their original
factory conditions, refer to “User Memory Reset“(p. 119).
NOTE
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start Playing
Rotating the External Memory
Connector Holder
Adjusting the Contrast of the
Screen
The External Memory connector holder rotates 90 degrees left
and right. Rotating the External Memory connector holder
allows you to avoid damaging the connected external memory
if something happens to bump against it.
You can adjust the contrast of the screen.
1. Turn the [LCD Contrast] knob (p. 121) located
at the bottom of the ATELIER to adjust the
contrast of the screen.
1. Grasp the External Memory connector holder
and turn it 90 degrees to the left or right.
Bright
Dark
External Memory
Holder
Songs you record on the ATELIER and registration sets you
create can be copied to separately available USB memory for
safekeeping. You can also copy songs to a floppy disk using a
separately sold floppy disk drive (p. 52, p. 65, p. 101).
You can also play back SMF music files saved on USB
memory or a floppy disk (p. 90).
90 degrees
to the left
90 degrees
to the right
Use USB memory and floppy disk drive available from
Roland. Proper operation cannot be guaranteed if other USB
device is used.
Security Slot
(Only for AT-300)
NOTE
988
If you’re using new USB memory or floppy disk, you’ll need
to initialize (format) it on the ATELIER. For details, refer to
“Formatting a USB Memory (Format)” (p. 120).
Security Slot (
http://www.kensington.com/
)
Be sure to grasp the External Memory connector holder itself
when rotating it. Never rotate the External Memory
connector holder by holding the connected external
memory.
NOTE
NOTE
Connecting the USB Memory
1. Connect the USB memory to the External
Take care not to allow your fingers to become pinched
when rotating the External Memory connector holder.
Memory connector.
931
Carefully insert the USB memory all the way in—until it is
firmly in place.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start Playing
Connecting the Floppy Disk Drive
(Sold Separately)
1. Attach the floppy disk drive as shown the
figure, using the mounting holes on the
ATELIER’s bottom panel.
For details of the attachment, refer to the owner’s manual of
the floppy disk drive.
2. Connect the USB cable of the floppy disk drive
to the ATELIER’s External Memory connector.
External Memory
Connector
USB Cable
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Start Playing
2. Connect the USB cable included with the CD
drive to the External Memory connector on the
ATELIER.
Using a CD
You can play back audio CDs and CD-ROMs containing
saved SMF music files.
3. Turn on the power to the ATELIER.
You can also play songs on VIMA CD-ROMs (VIMA TUNES)
sold by Roland.
4. Turn on the power to the connected CD drive.
For information on how to perform the following CD-drive
operations, refer to the owner’s manual for the drive.
Precautions Concerning Use of the CD
NOTE
• Switching the power on and off
• Inserting and ejecting a CD
• You cannot play back CD-R/RW disks to which audio
tracks have been added or CDs containing both audio
tracks and data (CD Extra).
A list of the CD drives that have been tested and found to be
compatible is available on the Roland website.
• The ATELIER is capable of playing back only commercial
CDs that conform the official standards-those that carry
the “COMPACT disc DIGITAL AUDIO” logo.
http://www.roland.com/
About the Adjuster
• The usability and sound quality of audio discs that
incorporate copyright protection technology and other
non-standard CDs cannot be guaranteed.
If you feel that the ATELIER has become unstable, for example
after moving it to another location, turn the adjuster located on
the bottom of the stand’s legs as shown in the following.
When turning the adjuster, be careful not to pinch your
• For more detailed information on audio discs featuring
copyright protection technology and other non-standard
CDs, please consult the disc vendor.
NOTE
hand.
• You cannot save songs to CDs, and you cannot delete
songs recorded to CDs. Furthermore, you cannot format
CDs.
• Rotate the adjustor to lower it so that it is in firm contact
with the floor. Make adjustments so that there is no gap
between the adjuster and the floor. In particular, when
placing the ATELIER on carpet, turn the adjuster so that it
is firmly in contact with the floor.
Connecting a CD Drive
(Sold Separately)
The ATELIER does not support CD drives that are powered
by the USB bus. If you use a USB-bus-powered CD drive,
NOTE
you must use the power supply included with the CD drive
so that the drive will operate under its own power.
External Memory
外部メモリー端子
connector
USB cable
1. Switch off the power to the ATELIER and the CD
drive to be connected.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Display
The ATELIER has three types of basic display screen: the Rhythm Screen, the
Composer Screen and the Registration Screen. You can alternate from one to
the other by pressing the [Display/Exit] button.
fig.01-17
Understanding the Main and Related Screens
Rhythm Screen
fig.01-18
Tempo
Beat Measure
Rhythm Name
Chord Name
Composer Screen
When internal music data is selected:
fig.01-19
Tempo
Beat Measure
Song Name
Chord Name
Registration Screen
fig.01-20
Tempo
Beat Measure
Registration Name
Next Registration set Name
Refer to “Load Next Function” (P.70).
Chord Name
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Listening to the Demo Songs
The ATELIER contains 8 Demo songs. Here’s how to play the Demo songs, and
fully appreciate the sounds, Rhythms, and Automatic Accompaniment that are
available with the ATELIER.
fig.02-01
NOTE
2
All rights reserved.
Unauthorized use of this
material for purposes other than
private, personal enjoyment is
a violation of applicable laws.
1
NOTE
The data for the Demo song
that is being played is not
available at the MIDI Out
connector.
3, 4
Check out the “Demo Song List”
(p. 114) for information such as
the names of the composers
and players of the demo songs.
1. Press the [Song] button and [Registration] button
simultaneously.
fig.02-02
2. Press the Value [-] and [+] buttons to select a Demo song.
3. Press the [Play/Stop] button to start playback of the demo
song.
When the selected demo song ends, the next demo song will begin playing.
4. To stop playback in the middle of the song, press the [Play/
Stop] button.
5. Press the [Song] button and [Registration] buttons
simultaneously to exit the demonstration screen.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
If the following screen appears
If the performance song in the ATELIER has not been saved to a USB memory
or Favorites (User Memory), the following message will appear, and it will not
be possible to play the Demo songs.
fig.02-03
If you don’t mind erasing this song, press the [Rec] button. However, if you
wish to save this song, press the [Reset] button to cancel the procedure, and
then save the song onto a USB memory or Favorites (User Memory).
If you wish to save the musical
data, refer to “Saving
Performance Songs” (p. 96)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Selecting Voices
The ATELIER is able to produce the sounds of various instruments. These
sounds are called “Voices.”
About the Voices and Parts
The ATELIER has two keyboards and one Pedalboard, as shown below.
From top to bottom these are called the “Upper Keyboard,” “Lower
Keyboard,” and “Pedalboard.”
fig.02-04
Upper Keyboard
Lower Keyboard
Pedalboard
The Upper Keyboard has two parts: “Upper,” “Vintage Organ.” You can
select one voice for each part, meaning that it is possible to layer the voices
on Upper Keyboard and play them simultaneously. The voice of the “Solo”
part can be layered on the Upper keyboard or Lower Keyboard.
The Lower Keyboard has two parts: “Lower” and “Vintage Organ“
The Pedalboard has the part: “Pedal.”
Keyboard
Part
Upper
Upper Vintage
Solo
Upper Keyboard
(This voice is sounded only when the Solo [To Lower] button
lights up)
To play a Solo voice on the
Lower keyboard, select the Solo
voice and press the Solo [To
Lower] button (p. 84).
Lower
Lower Vintage
Solo
(This voice is sounded only when the Solo [To Lower] button
lights up)
Lower Keyboard
Pedalboard
Pedal
(This voice is sounded when the Pedal [To Lower] button
lights up or turn ”Bass Split” on)
Pedal
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Functions of the Upper/ Lower /Pedal Bass Sound Select
Buttons
fig.02-05
NOTE
If none of the voice buttons or
Vintage organ button are lit,
playing the keyboard will not
produce a sound.
Each time you press a voice button, its indicator will switch between being lit
and being turned off. Voices that have their button indicator lit can be played.
Selecting the Upper/Lower/Pedal Bass Voices
Select voices by pressing the Upper, Lower and Pedal Bass Voice Part buttons.
When the power is turned on, the Upper keyboard will play “Full Organ 3,”
the Lower keyboard will play “Lower Organ2” and the Pedal Bass voice will
sound single notes using the “Organ Bass1” voice.
Example:
Selecting “Orch.Brs Ens” for the Upper Organ Part
NOTE
If you press the Pedal [To
Lower] button (indicator lights
p. 88), the Pedal Bass voice
can now be played by the
Lower keyboard, not by the
Pedalboard.
1. Press the Upper [Brass] button (indicator lights).
The name of the selected voice appears in the display for several seconds.
fig.02-06
Now when you play the Upper keyboard, the “Orch.Brs Ens” will sound.
You can select the Lower Voice or Pedal Bass Voice in the same way as the
Upper Voice.
Settings can be adjusted to
allow multiple notes to be
played on the Pedalboard (p.
106).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
NOTE
Selecting Solo Voice
If you press the Solo [To Lower]
button (indicator lights (p. 84),
the Solo voice can now be
played by the Lower keyboard,
not by the Upper Keyboard.
The Solo section of the Upper keyboard is monophonic, that is, the Solo voice
will only sound for the highest note played on the Upper keyboard.
fig.02-11
It is possible to change how a
Solo voice will sound.
Normally, the Solo voice will
be sounded by the highest note
you play on the Upper
1. Press the Solo [Sax] button (indicator lights).
You can also make settings so
that the Solo voice will be
sounded by all notes of the
keyboard to which the Solo
voice is assigned. For details
refer to “Changing How the
Solo Voice Responds (Solo
Mode)” (p. 85).
The name of the selected voice appears in the display for a few seconds.
fig.02-12
Play the Upper keyboard. The selected voice will sound by the highest note
played.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Selecting a Voice Using the [Others] Button
Notice that there is an [Others] button for each part. By using the [Others]
button, you can select all voices.
You can jump by voice group
by pressing Menu [
] [
]
1. Press the [Others] button for the Part for which you wish to
buttons to select the voice.
The sound number of each
voice is preceded by an
alphabetical character A–U
(AT-100) or A–V (AT-300)
which indicates the sound
group; e.g., “G11 Strings1.”
specify a voice.
The voice name appears in the display.
fig.02-10 (P.29)
The indicator of the selected [Others] button will light.
2. While the voice name is shown in the display screen, use
You can also press the key for
the part containing a changed
voice to confirm the voice
setting.
the Value [-] [+] buttons to select the desired voice.
The indicator of the selected [Others] button will blink.
To stop mid-way through this or any procedure, press the [Display/Exit]
button.
3. Once again, press the [Others] button for the part whose
sound you wish to set to confirm the voice.
About the voices that can be
assigned to an [Others] button,
please refer to ”Voice & Rhythm
List.”
The indicator of the [Others] button will change from blinking to light.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Creating Organ Sounds (Vintage Organ)
The Vintage Organ button lets you add vintage organ sounds to the upper and
lower parts.
In addition, you can also use the harmonic bars to modify the selected sound
as desired.
The ATELIER provides nine harmonic bars for the upper part and lower part.
Each harmonic bar is assigned a sound of a different footage (pitch), and by
layering these sounds you can create a variety of organ tones.
Harmonic Bar
By sliding the harmonic bars forward or backward (in or out), you can adjust
the volume of the various footages.
The volume can be adjusted over nine steps (0–8).
When a harmonic bar is pulled out all the way (8), the volume is loudest.
When it is pushed in all the way (0), there will be no sound.
8' is the footage that forms the basic pitch of the sound; this is the center
around which you create the tone.
Each harmonic bar is assigned a sine wave (a pure pitch without overtones)
of a different pitch, and by combining these pitches you can create a wide
range of sounds.
Time
8' volume: 8
Time
Time
4' volume: 5
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
What’s the feet?
“Feet” is a term that began as a measurement of the length of the pipes
in a pipe organ.
The pipes that produce the basic pitch (fundamental) for each note are
considered to be “8 feet” in length.
Therefore, a pipe producing a pitch one octave below that of the
reference of 8' (eight feet) would be 16’; for one octave above the
reference, the pipe would be 4', and to take the pitch up yet another
octave it would be shortened to 2'.
The pitches of the harmonic bars are related as follows.
When the middle C (C4) note is pressed, each
harmonic bar will sound the following notes.
16'
51/3
'
8'
4'
22/3
12th
'
2'
13/5
17th
'
11/3
19th
'
1'
15th
one octave 5th
below
root
8th
22nd
8' =
On tonewheel organs, the high-pitched footage for a portion of the high
range, and the low-pitched footage for a portion of the low range are
“folded-back” in units of one octave.
Folding back the high-frequency portion prevents the high-frequency
sounds from being unpleasantly shrill, and folding back the low-
frequency portion prevents the sound from becoming “muddy.”
On the ATELIER faithfully simulates this characteristic.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Playing a Vintage Organ Voice
Turning on the Vintage Organ
1. Press the Vintage Organ [On/Off] button so its indicator is
lit.
Each time you press the button, the indicator will alternate between ON (lit)
and OFF.
The Vintage Organ screen will
be displayed for several
seconds, then it will close
automatically.
The Vintage organ screen appears.
fig.01-24.eps
NOTE
Glide and sustain effects are
not applied to the Vintage
Organ voice.
The screen will show value for the harmonic bars.
When a harmonic bar is pulled out all the way (8), the volume is loudest.
When it is pushed in all the way (0), there will be no sound.
Modifying the Sound
1. Press H-Bar Part [Upper] or [Lower] buttons to select a part
for which the harmonic bars are available.
2. Slide the harmonic bars that you want to hear.
You can layer the sound of multiple harmonic bars.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Adding Sparkle to the Sound (Percussion)
This adds an attack sound to the beginning of the note, making the sound
crisper.
NOTE
When the Percussion [2 2/3']
button is on, the 1' pitch will
not be produced.
1. Press the Percussion [2 2/3'] button so its indicator is lit.
Play the Upper keyboard and notice that an attack has been added.
NOTE
The Percussion [2 2/3'] button
are valid only for vintage organ
voices of the upper part.
Button
Explanation
Percussion [2 2/3'] button Percussion one octave and a fifth above
Adjusting the Rate at which the Percussion Decays
You can shorten the decay time of the percussion sound.
1. Press the Percussion [Fast Decay] button to switch the
indicator between lit/unlit.
[Fast Decay] Button
Lit
Explanation
The percussion sound will disappear quickly.
The percussion will have a sharper attack.
The percussion sound will disappear slowly.
The percussion will have a more gentle attack.
Unlit
Using the Harmonic Bar Settings of the Panel
If you’ve switched registrations so that the Vintage Organ settings have
changed, you can switch the Vintage Organ settings to the positions (settings)
of the harmonic bars on the panel.
1. Press the H-Bar Part [Upper] or [Lower] button whose
indicator is lit.
The part whose indicator is lit will have the settings of the harmonic bar
positions (settings) of the panel.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Adjusting the Volume of the Vintage Organ
You can adjust the volume of the Vintage Organ sound to regulate the volume
balance relative to the other sounds.
1. Press the [Utility] button.
fig.05-08.eps
2. Press the Menu [ ] and [ ] buttons to select
“VintageOrganVolume.”
fig.VoiceList.eps
3. Press the Value [-] and [+] buttons to select the value for
volume of the vintage organ.
Setting
0–12
4. To return to the basic screen, press the [Utility] button.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Performing with an Active Expression Voice
For “Active Expression Voices,” operating the expression pedal will control
not only the volume but also the tone, or may add additional sounds.
1. Press the [Others] button of the Part to which you want to
assign an Active Expression voice.
The voice name appears in the display.
The indicator of the selected [Others] button will light.
2. Press the Value [-] and [+] buttons to select the Active
Expression Voice.
For details on the Active
Expression voices that are
available, refer to “Voice list”
(Appendix: separate booklet).
The indicator of the selected [Others] button will blink.
Active Expression Voices have the letters “AEx” preceding their voice name.
To stop mid-way through this or any procedure, press the [Display/Exit]
button.
3. Once again, press the [Others] button for the part whose
sound you wish to set to confirm the voice.
You can press the key for the
part containing a changed
voice to confirm the voice
setting.
The indicator of the [Others] button will change from blinking to light.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Adjust the Volume Balance
The ATELIER allows you to adjust the volume balance individually for each
Part.
fig.02-13
The following buttons are used to adjust the volume of a multiple number of
Parts.
t
Button
Part
Automatic Accompaniment (except Bass)
Playback of performance songs from
something other than the ATELIER performance
songs (for example: SMF music files)
Accomp/SMF [▲] [▼] button
Rhythm performance
Drums/SFX
Pedal voice
Pedal Level [▲] [▼] button
Bass note of automatic accompaniment
1. The volume levels of each part are adjusted using the
corresponding [▲] and [▼] buttons.
Pressing the [▲] button will increase the volume.
Pressing the [▼] button will decrease the volume.
The volume can be set to any value from 0 to 12.
When the volume value shown in the display is 0, that part will produce no
sound.
You can also press the [▲] button or [▼] button of the part whose volume you
wish to adjust, so that the “Part Balance Monitor” screen is displayed for
several seconds, allowing you to check the volume balance.
The Part Balance Monitor
screen is displayed for several
seconds and then closes
automatically.
fig.02-14
R
A
P
L
Reverb
Accomp/SMF
Pedal
Lower
U
S
Upper
Solo
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Transpose the Pitch in Octave Units (Octave Shift)
The pitch of the sound played by the keyboard can be adjusted in one-octave
steps. This function is called “Octave Shift.”
You can apply an Octave shift to the following 4 Parts:
The Upper Part
The Lower Part
The Pedal bass Part
The Solo Part
1. Press the [Utility] button.
2. Press the Menu [ ] and [ ] buttons to select “Octave
Shift.”
f
3. Press the [Rec] button.
4. Use the Menu [ ] and [ ] buttons to select a Part to
which you wish to apply an Octave Shift.
Part
Pedal, Lower, Upper, Solo
fig.02-16
5. Use the Value [-] and [+] buttons to set the amount of shift.
NOTE
The value can be set to a range of +/- 3 octaves.
Please note that when you
apply the Octave Shift function
to certain voices, their pitch
could be stretched beyond their
recommended note ranges, and
they may not sound as
To return to the basic screen, press the [Utility] button.
expected. Care should be taken
when using Octave Shift.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Sustaining Notes Played on the Lower Keyboard
You can have the sound for keys in the Lower keyboard continue to play, even
after you release the key, until the next key is pressed.
1. Hold down the Pedal [To Lower] button for several seconds
This setting is saved to the
registration.
until its indicator begins blinking.
Pedal [To Lower] button will
also turn on at this time.
The following appears in the screen.
The notes played on the lower keyboard will continue sounding.
2. Press the Pedal [To Lower] button so its indicator goes out.
The sound stops playing.
Playing Drums from the Entire Lower Keyboard (Drums/SFX)
You can use the Lower keyboard to play various drum sounds (drum set). In
this case, the Lower voices will no longer sound.
fig.02-18
Refer to for “Voice & Rhythm
List” (Appendix: separate
booklet) details on which drum
sound or Sound Effect will be
played by each note.
1. Press the [Drums/SFX] button (indicator lights).
Play the Lower keyboard and listen to the various drum sounds on each key.
The [Drums/SFX] button will alternate between on (lit) and off each time it is
pressed.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting and Playing Sounds
Changing the Drum/SFX Set
NOTE
Immediately after the power is turned on, the STANDARD drum set will sound.
Let’s try selecting a different Drum Set or the Sound Effect set.
For some drum sets, there will
be keys that do not sound.
As the drum set, you can choose from 13 types (AT-300) or 9 types (AT-100)
of drum set. When you change the drum set, the sound produced by each note
will change.
fig.02-19
Refer to “Voice & Rhythm List”
(Appendix: separate booklet)
for details on which drum
sound or Sound Effect will be
played by each note.
1, 3
2
1. Press the [Drums/SFX] button (indicator lights).
2. When the Drum Set name is displayed on the screen, press
the Value [-] [+] buttons to select a Drum Set or Sound Effect
Set.
The [Drums/SFX] button indicator will begin to blink.
fig.02-20
You can select from 13 (AT-300) or 9 (AT-100) different Drum Sets and one
set of Sound Effects as follows:
AT-300
STANDARD, STANDARD 2, ROOM, ROOM2, POWER, ELECTRONIC,
TR-808, DANCE, JAZZ, BRUSH, BRUSH2, ORCHESTRA, SOUND EFFECTS
AT-100
STANDARD, ROOM, POWER, ELECTRONIC, TR-808, JAZZ, BRUSH,
ORCHESTRA, SOUND EFFECTS
To stop mid-way through this or any procedure, press the [Display/Exit]
button.
3. Press the [Drums/SFX] button once again.
You can also play the lower
manual to confirm the drum set.
The [Drums/SFX] button indicator will light constantly, and the selected Drum/
SFX set will be applied.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
The ATELIER lets you enjoy playing along with a rhythmic accompaniment.
Selecting a Rhythm
The AT-300 provides 120 types and The AT-100 provides 80 types of
Rhythms and Automatic Accompaniments (Music Styles). These are organized
into four groups.
Each rhythm button corresponds to two groups.
By pressing a button that is lit, you can select that button’s other group.
For more on the internal
rhythms, refer to “Voice &
Rhythm List” (Appendix:
separate booklet).
The selected group is shown by the illumination status of the two indicators
located beside the rhythm buttons.
Indicators located beside
Descriptions
the rhythm buttons
The rhythm group printed above the button is selected.
Upper indicator lit
(Big Band, Country, Oldies, Ballad)
The rhythm group printed below the button is selected.
(Latin, Waltz, Trad, User)
Lower indicator lit
If you’ve selected the “Big Band” group, the indicators shown below will light.
fig.03-01
2
1, 3
1. Press a Rhythm button to select a Rhythm group.
The indicator of Rhythm button will light.
That Rhythm will be shown in the display.
fig.03-02
2. Press the Value [-] and [+] buttons to select a different
Rhythm within the same group.
The indicator of the Rhythm button will blink.
3. Press the flashing rhythm button once more.
The Rhythm button’s indicator will change from blinking to light.
The Rhythm has now been applied.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Rhythms Stored in User Memory
If you wish to copy a Rhythm
saved on USB memory to User
memory, refer to “Copying
Rhythms” (p. 52).
The ATELIER features a User memory.
What is User Memory?
“User Memory” refers to an area inside the instrument where you can store
the registration you create and the performances you record. Registration
and SMF music files saved on USB memory can also be copied to user
memory (p. 52).
User memory is quite useful, since anything you place there will be
retained even while the power is turned off.
The following things are stored in User memory:
• Songs you’ve registered in “Favorites”
• Rhythms
If you want to restore the
original rhythms that User
memory contained at the time
the instrument was shipped
from the factory, refer to
“Restoring the User Memory to
the Original Factory Settings
(User Memory Reset)” (p. 119).
• Registration sets
The ATELIER is shipped from the factory with rhythms already stored in User
memory. These rhythms can be overwritten by copying. The content of User
memory is retained even while the ATELIER’s power is turned off.
You can call up rhythms in User memory by selecting the User group.
Calling Up Rhythms Stored in User Memory
1. Press the Rhythm [Ballad/User] button a number of times to
select the user group.
The Rhythm screen appears.
2. Press the [Media] button to select “User.”
If USB memory is connected,
you can select “Ext Memory” so
that rhythms in the USB memory
will be shown.
The rhythms stored in user memory will be shown.
If floppy disk is connected, you
can select “Disk” so that
rhythms in the floppy disk will
be shown.
3. Press the Value [-] and [+] buttons to select a different
Rhythm within the same group.
The indicator of Rhythm [Ballad/User] button will blink.
4. After selecting a rhythm, press the blinking Rhythm
[Ballad/User] button once more.
The Rhythm [Ballad/User] button stops blinking and remains lit, indicating that
the rhythm has been selected.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Playing Rhythm
There are two ways to start the rhythm. You can press the [Start/Stop] button
to start the rhythm, or you can use Synchro Start to have the rhythm start when
you play the lower keyboard or the pedalboard.
The functions of the [Intro/
Ending] button and [Start/Stop]
button can be assigned to the
foot switches located on each
side of the Expression Pedal (p.
69).
You can also make the rhythm start with an intro, or stop with an ending.
fig.02-03_AT-900.eps
Starting at the Press of a Button
Starting with an Added Intro
1. Press the [Intro/Ending] button.
2. Press the [Start/Stop] button.
The Intro is played and the Rhythm starts.
While the Intro is playing, the [Intro/Ending] button indicator will light, until
the Intro ends then the button indicator will go dark.
Starting Without an Intro
1. Press the [Start/Stop] button.
The Rhythm starts without an Intro being played.
For more on the Variation
buttons, refer to “Adding
Variety to the Rhythm or
Automatic Accompaniment” (p.
47).
Making the Intro Short and Simple
1. Press the Variation [1] button.
2. Press the [Intro/Ending] button.
The [Intro/Ending] button indicator will light.
3. Press the [Start/Stop] button.
A short Intro is played and the Rhythm starts.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Starting the Rhythm Automatically When You Play the Lower
Keyboard or Pedalboard (Synchro Start)
Starting with an Added Intro
1. While holding down the Arranger [On/Off] button, press
Auto [Fill In] button to turn Synchro Start on.
The [Start/Stop] button indicator will blink.
2. Press the [Intro/Ending] button.
The [Intro/Ending] button indicator will light.
NOTE
3. Play either the Lower keyboard or the pedalboard.
If the Arranger function is ON
(the Arranger [On/Off] button
indicator is lit), it is not be able
to start the Rhythm by playing
the Pedalboard (p. 46).
The Intro is played and the Rhythm starts.
While the Intro is playing, the [Intro/Ending] button indicator will light, until
the Intro ends then the button indicator will go dark.
Starting Without an Intro
1. While holding down the Arranger [On/Off] button, press
Auto [Fill In] to turn Synchro Start on.
The [Start/Stop] button indicator will blink.
2. Play either the Lower keyboard or the pedalboard.
The Rhythm starts without an Intro being played.
Starting with the Intro Short and Simple
1. While holding down the Arranger [On/Off] button, press
Auto [Fill In] to turn Synchro Start on.
The [Start/Stop] button indicator will blink.
2. Press the Variation [1] button.
For more on the Variation
button, refer to “Adding Variety
to the Rhythm or Automatic
Accompaniment” (p. 47).
3. Press the [Intro/Ending] button.
The [Intro/Ending] button indicator will light.
4. Play either the Lower keyboard or the pedalboard.
A short Intro is played and the Rhythm starts.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Stopping the Rhythm
The functions of the [Intro/
Ending] button and [Start/Stop]
button can be assigned to the
foot switches located on each
side of the Expression Pedal (p.
69).
Stopping with an Ending
1. Press the [Intro/Ending] button.
An Ending is played, then the Rhythm stops.
While the Ending is playing, the [Intro/Ending] button indicator will light, until
the Ending finishes the button indicator will be turned off.
Stopping without an Ending
1. Press the [Start/Stop] button.
The Rhythm stops without an Ending being played.
Stopping with the Ending Short and Simple
1. Press the Variation [1] button.
2. Press the [Intro/Ending] button.
A short Ending is played, then the Rhythm stops.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Changing a Tempo of Rhythm and Automatic Accompaniment
You can change the tempo of the Rhythm or Automatic Accompaniment.
fig.03-06(P.40)
If you switch rhythms when
“Auto Std Tempo” (p. 108) is
on, the tempo changes to
match the rhythm. If you switch
rhythms when “Auto Std
Tempo” is off, the tempo
1. Press the Tempo [ ] and [ ] buttons to change the
remains unchanged even when
tempo (speed) of the Rhythm or Automatic Accompaniment.
you switch the rhythm.
The tempo becomes slower
The tempo becomes faster
Tempo [
Tempo [
] button
] button
By pressing the Tempo [
]
and [
] buttons
simultaneously, the tempo is
returned to the standard (preset)
tempo for the selected Rhythm.
The value of the tempo currently set (20–500 beats per minute) can be
checked in the display.
You can also check the tempo by viewing the Beat indicator.
Playing a Countdown Sound When the Intro Ends
If an intro is played before your performance, you can have a countdown
played to the end of the intro, allowing you to understand easily where you
are to start playing.
1. Press the [Utility] button.
2. Using the Menu [ ] and [ ] buttons, select
“Intro Count Down.”
You can adjust the volume of
“Adjusting the Metronome
Volume (Metronome Volume)”
(p. 111).
3. Press the Value [-] and [+] buttons to switch the Intro Count
Down “ON” or “OFF.”
4. Press the [Intro/Ending] button.
You can change the countdown
sound (p. 108).
5. Press the [Start/Stop] button.
The intro plays, and a countdown plays to the end of the intro.
When the Synchro Start is on, specifying the chord on the Lower keyboard
starts the intro, and again, a countdown is given.
To return to the basic screen, press the [Utility] button.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Playing Rhythm and Automatic Accompaniment
The Arranger function of the ATELIER can add an Automatic Accompaniment
to each Rhythm. Based on the selected Rhythm, the Arranger function
automatically adds an accompaniment that is suitable for the chord being
pressed on the Lower keyboard.
fig.02-06.eps
NOTE
When the Arranger [On/Off]
button is on, Synchro Start (p.
43) on the pedalboard cannot
be used.
Arranger [On/Off] button
Function
Rhythm and Automatic Accompaniment
Rhythm
Lit (On)
Unlit (Off)
2. Start the rhythm (p. 42).
The rhythm and the automatic accompaniment will play together.
NOTE
If the Arranger [On/Off] button is ON and no Pedal Bass voice is selected,
the Automatic Accompaniment will play the bass sound.
The lower voice is not played
during the performance of the
intro and ending, even when
the Lower keyboard is played.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Adding Variety to the Rhythm or Automatic Accompaniment
You can add variety to the rhythm or automatic accompaniment by changing
the rhythm pattern of the rhythm.
fig.02-07_AT-900.eps
Button name
Function
A fill-in will automatically be added when you press
a Variation [1]–[4] button to change the
accompaniment or rhythm arrangement.
Auto [Fill In] button
What’s a fill-in?
A Fill In is a short phrase that is inserted at a break in the melody or at a point
where the character of the song changes (between Chorus’s or Verses).
Changing the Arrangement of the Rhythm and
Accompaniment (Variation)
You can change the arrangement of the accompaniment. This function is
called “Variation.” For each rhythm, there are four types of arrangement for
the accompaniment.
The following buttons are called Variation buttons.
fig.02-08_AT-900.eps
1. Press the Variation [1]–[4] buttons to change the
arrangement of the accompaniment.
The functions of the Variation
buttons can be assigned to the
foot switches located on each
side of the Expression Pedal.
Please refer to “Changing the
Function of the Foot Switch” (p.
69).
The indicator of the button you pressed will light.
The Variation [1] button produces the simplest arrangement, and the [4]
button produces the most florid.
For an intro or ending, Variation [1] is the shortest and simplest.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Turning Chord Intelligence On/Off
“Chord Intelligence” is a feature that intelligently plays the correct
accompaniment chords the moment you play a key specifying a chord on the
Lower keyboard during Automatic Accompaniment.
To play a C chord on the Lower keyboard, for example, you usually have to
press down the three keys C, E, and G; but with Chord Intelligence, you only
have to press the C Key to initiate a C chord accompaniment.
1. Press the [Utility] button.
For more information about
chord fingering, see the “Chord
List” (p. 130).
2. Press the Menu [ ] and [ ] buttons to select “Chord
Intelligence.”
fig.12-29
3. Press the Value [-] and [+] buttons to switch the Chord
Intelligence “ON” or “OFF.”
When the [One Touch
Program] button is pressed, the
Chord Intelligence function is
automatically switched ON.
Setting
Descriptions
ON
Chord Intelligence function is ON.
Chord Intelligence function is OFF.
OFF
To return to the basic screen, press the [Utility] button.
When the Leading Bass
function (p. 49) is on and the
Chord Intelligence function is
off, you can specify chords with
a combination of the lower
keyboard and pedalboard.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Leading Bass Function
When Automatic Accompaniment is used, and the Pedal [To Lower] button is
ON, the Pedal Bass voice will normally play the root note (p. 132) of the
chord you play on the Lower keyboard. If the Leading Bass function is
enabled, the lowest note of the chord you play on the Lower keyboard will
then be used as the bass note (the bottom note of the chord).
For this reason, the bass note will be sounded differently than normal when
you play an inverted chord (p. 132).
1. Press the [Utility] button.
You can assign the Leading
Bass functions to either of the
foot switches located on each
side of the Expression Pedal (p.
69).
2. Press the Menu [ ] and [ ] buttons to select “Leading
Bass.”
3. Press the Value [-] and [+] buttons to switch the Leading
Bass “ON” or “OFF.”
Setting
Descriptions
The Leading Bass function is ON.
The pedal bass tone will sound the lowest note of the chord
you play in the lower keyboard.
ON
When the Leading Bass
function (p. 49) is on and the
Chord Intelligence function is
off, you can specify chords with
a combination of the lower
keyboard and pedalboard.
OFF
The Leading Bass function is OFF.
To return to the basic screen, press the [Utility] button.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
A Simple Way to Make Automatic Accompaniment Settings
(One Touch Program)
When using the Arranger function for automatic accompaniment, you can
also use the “One Touch Program” function to automatically select panel
settings that are appropriate for the selected rhythm.
By pressing the [One Touch Program] button, you can make the following
settings.
• Panel settings (e.g., sounds and volume) suitable for the rhythm
• Automatic Accompaniment playing
• [Start/Stop] button blinking (Waiting for Synchro Start)
• Chord Intelligence function is ON (p. 48)
What is Synchro Start?
Synchro Start is a function that starts the rhythm at the moment that you
play the lower keyboard.
What is Chord Intelligence?
“Chord Intelligence” is a feature that intelligently decides on
accompaniment chords the moment you play some keys specifying a
chord during automatic accompaniment.
1. Select a Rhythm (p. 40).
NOTE
2. Press the [One Touch Program] button.
When you press the [One
Panel settings appropriate for the rhythm and automatic accompaniment will
automatically be called up for Registration [1]–[4] buttons.
Touch Program] button, the
“Arranger Update” setting will
automatically change to
“INSTANT” (p. 57).
3. Press the Registration [1] – [4] buttons to select panel
settings.
4. On the Lower keyboard, play a chord.
At the moment you play the keyboard, the Intro will begin, and then the
Rhythm and Automatic Accompaniment will play.
5. Press the [Intro/Ending] or [Start/Stop] button to stop the
Rhythm.
Rhythm and Automatic Accompaniment stops.
6. Press the [One Touch Program] button, extinguishing its
indicator.
The One Touch Program function is turned off, and the panel settings in effect
prior to the [One Touch Program] button being pressed are restored.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Using a Rhythm from a USB Memory
NOTE
The ATELIER contains a variety of rhythms, but you can also use rhythms from
USB memory or floppy disk to perform rhythms in an even wider range of
styles.
All rights reserved.
Unauthorized use of
commercially available Music
Style disk for purposes other
than private, personal
enjoyment is a violation of
applicable laws.
Reviewing the Styles on USB Memory
1. Connect the USB memory containing the rhythms to the
external memory connector.
If you want to use rhythms from
a floppy disk, connect the
floppy disk drive (sold
separately) to the external
memory connector.
2. Press the Rhythm [Ballad/User] button a number of times to
select “User group.”
The Rhythm screen appears.
fig.02-21-1.eps
3. Press the [Media] button to select “Ext Memory” and see
If “User” is selected, the
rhythms saved in User memory
(p. 41) will be shown.
the rhythms in USB memory.
The Rhythm screen will show the Rhythms on the USB memory.
fig.02-21.eps
If “Disk” is selected, the rhythms
saved on the floppy disk will be
shown.
4. Press the Value [-] and [+] buttons to select a Rhythm.
If you copy rhythms from USB
memory or floppy disk into user
memory (p. 41), you’ll be able
to access those rhythms simply
by pressing the Rhythms
The [Start/Stop] button indicator will blink while the Rhythms are being
loaded into internal memory.When loading is finished, you will be able to
play the selected rhythm.
[Ballad/User] button (p. 52).
5. Press the [Start/Stop] button.
The selected Rhythm is played.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Copying Rhythms
User memory (p. 41) already contains rhythms, but you can replace these
rhythms with rhythms from USB memory or floppy disk. Rhythms copied from
the USB memory into User memory will not be lost even if the power is turned
off. It is convenient to copy frequently-used Rhythms into User memory.
Copying Rhythms from USB Memory to User Memory
1. Connect the USB memory to the external memory
If you want to copy rhythms
from floppy disk, connect the
floppy disk drive (sold
separately) to the External
memory connector.
connector.
2. Press the [Utility] button.
3. Press the Menu [ ] and [ ] buttons to select “Media
Utility.”
fig.02-09.eps
4. Press the [Rec] button.
NOTE
5. Press the Menu [ ] and [ ] buttons to select “Copy
If no USB memory or floppy
disk is inserted, you won’t be
able to choose “Copy Rhythm”
in the Utility menu.
Rhythm.”
fig.02-10.eps
6. Press the [Rec] button.
7. Press the [Media] button to select the media (the location of
the rhythm you want to copy).
If you want to copy a rhythm from USB memory, select “Ext Memory.”
If you want to copy a rhythm from floppy disk, select “Disk.”
8. Press the Value [-] and [+] buttons to select the rhythm you
want to copy.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
9. Press the [Rec] button.
10. Press the Value [-] and [+] buttons to select the copy-
destination number.
To cancel the procedure, press the [Display/Exit] button.
11. Press the [Rec] button to copy the rhythm.
While the Rhythm is being copied into internal memory, the following
screen will be displayed.
NOTE
Never remove the USB memory
rhythm data is being copied
from USB memory into the
ATELIER. If you do so, the
rhythm data will not be loaded
into the ATELIER, and
malfunctions could result. After
returning the rhythm stored in
the user memory to the factory
settings (p. 119), copy the
rhythm from USB memory once
more.
If you select a number in which a rhythm is already saved, a screen like the
following appears.
If you want to delete the previously saved rhythm and overwrite it with the
rhythm you’re newly saving, Press the [Rec] button.
If you don’t want to delete the previously saved rhythm, press the [Reset]
button, then select a number at which no rhythm has been saved, and copy
the rhythm to that number.
You can return only the user
memory to the factory settings.
Refer to “Restoring the User
Memory to the Original Factory
Settings (User Memory Reset)”
(p. 119).
To return to the basic screen, press the [Utility] button.
Copying Rhythms from User Memory to USB Memory
You can copy rhythms from user memory to USB memory.
To do so, press the [Media] button in step 7 (above) to choose “User.” In this
state, you’ll be copying rhythms from user memory to USB memory.
The rest of the procedure is the same as when copying rhythms from USB
memory to user memory.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Rhythm Performance
Deleting Saved Rhythm
You can delete rhythms stored in User memory (p. 41) or USB memory.
1. Select the rhythm you want to delete (p. 41).
2. Press the [Load] button and [Save] buttons simultaneously.
The following display appears.
fig.02-10.eps
To cancel the procedure, press the [Reset] button.
NOTE
3. Press the [Rec] button.
Never turn off the power while
the operation is in progress.
Doing so will damage the
ATELIER’s internal memory or
USB memory, making it
unusable.
While the Rhythm is being deleted, the following screen will be displayed.
When saving is complete, the basic screen reappears.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
The ATELIER allows you to store sound settings and panel settings such as 8 in
the Registration buttons. There are a total of 8 Registration buttons, and one
set of panel settings can be stored in each, allowing you to register a total of
8 different panel settings. Each set of panel settings that has been stored in a
Registration button is called a “Registration.”
to Registration [1]–[8] buttons
are remembered even if the
power is turned off. If you wish
to restore the settings stored in
the Registration buttons to their
factory settings, use the
This provides a convenient way to change large numbers of panel settings
during a performance, or to recall a complex panel setting.
“Factory Reset” operation (p.
19).
fig.07-01
Manual
Write
1
2
3
4
5
6
7
8
About the Registration Buttons
In addition to assigning voices and rhythms to the Registration buttons, you
can also store the following settings:
• Controller settings (functions assigned to foot switches, etc.)
• Other types of settings (reverb type, tempo settings, degree of initial
touch, etc.)
Recorded performance data
and rhythms from User memory
(p. 41) are not stored in
Registration sets.
If you would like to know all of the settings that can be recorded to the
Registration buttons, refer to “Settings That Are Stored In the Individual
Registration Buttons” (p. 134).
When a rhythm saved in User
memory is assigned to a
Registration set, that rhythm is
copied beforehand to the User
memory.
USB memory, a floppy disk, or user memory (p. 60).
In addition to the settings saved to the Registration buttons, the following data
is also saved when Registration sets are saved.
• Registration Name →p. 58
• Registration Shift →p. 70
• Arranger Update →p. 57
• Trans. Update (Transpose Update) →p. 109
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
Procedure for Creating Registration Sets
Prepare the Registrations
A convenient way to make the sequence of Registration buttons to be pressed
easy to understand is to store the panel settings starting from the Registration
[1] button, continuing with subsequent buttons in accordance with the
progression of the song.
Save the Registrations to the USB memory or User memory
If you want to use more than eight Registrations in a song, save the settings
for Registration buttons [1]–[8] to a USB memory or User memory as a set,
then continue to store further panel settings again, starting from Registration
button [1]. Save all of the Registration sets you have set to the USB memory or
user memory.
Arrange the Registrations in the sequence they are to be used
Save the Registration sets to the USB memory or user memory in the order they
are to be used in the song.
Using Registration Sets
Call up the Registration sets saved on the USB memory to the ATELIER
memory connector, and read the Registration sets into the ATELIER.
Switch the Registration sets as you perform
Press the Registration buttons to switch Registrations as you play the song.
If you want to recall the next registration set, assign the foot switch to “Switch
Registrations + Load Next function,” and recall the next registration set (p.
70).
Storing Registrations
1. Make all the panel settings that you wish to store.
2. While holding down the [Write] button, press one of the
Registration [1] – [8] buttons.
The panel settings will be stored in the selected Registration button.
For details on the settings that
are stored in a Registration,
refer to “Settings That Are
Stored In the Registration
Buttons” (p. 134).
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
Recalling a Registration
There are two ways of calling up the settings affecting the rhythms registered
to the Registration buttons [1]–[8], “INSTANT” and “DELAYED.” At the factory
this is set to “DELAYED.”
How to Recall a Registration
Recalling Voices and Other Panel Settings
1. Press a Registration [1]–[8] button.
Recalling Settings for Rhythm and Automatic
Accompaniment in Addition to the Panel Settings
1. Press and hold a Registration [1]–[8] button for several
seconds.
The indicator of the rhythm select button will blink, and the panel settings and
settings related to rhythm performance and automatic accompaniment will be
recalled.
Changing the Timing of Recalling Registrations
Settings for Rhythm play and Automatic Accompaniment are recalled when
you continue holding a Registration [1]–[8] button for several seconds, but you
can change this so that the settings are recalled the instant you press the
button.
1. Press the [Utility] button.
2. Press the Menu [ ] and [ ] buttons to select the
“Arranger Update.”
fig.07-02
You can change the timing of
recalling the transpose setting
when you press a Registration
[1]–[8] button. For more
information, please refer to
“Adjust the Standard Pitch
(Master Tune)” (p. 114).
3. Press the Value [-] and [+] buttons to switch between
“DELAYED” and “INSTANT.”
When you press and hold a Registration [1]–[8] button for several
seconds, the settings for Rhythm and Automatic Accompaniment will be
DELAYED recalled in addition to the panel settings. If you press and immediately
release a Registration [1]–[8] button, only the settings that are not
related to Rhythm or Automatic Accompaniment will be recalled.
Settings for Rhythm and Automatic Accompaniment will be recalled the
INSTANT
instant that you press a Registration [1]–[8] button.
To return to the basic screen, press the [Utility] button.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
Automatically Registering When You Switch Panel Settings
When the [Manual] button is ON (lit), all panel settings you make will be
stored automatically in the [Manual] button as they are made, thus updating
the Registration that had been previously saved. If you change to a preset
Registration [1]– [8] button, it is possible to return to the previous panel
settings by pressing the [Manual] button.
NOTE
The settings stored in the
[Manual] button returns to the
default settings while the power
is turned off.
fig.07-03
Manual
Write
1
2
3
4
Assigning a Name to a Registration Set
When saving Registration sets, names like “Factory Reg.” will be assigned by
default, but you can assign a name that will help you later to identify the
contents of the Registration set.
fig.07-03
3
3
1
2,4
1. Press the [Display/Exit] button a number of times to access
the registration screen.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
2. Press the [Registration] button and the [Media] button
simultaneously.
3. Press the Menu [ ] and [ ] buttons to move the cursor,
and press the Value [-] and [+] buttons to select a
character.
fig.07-05
The following characters can be selected
.
space ! “ # % & ’ ( ) * + , - . / : ; = ? ^ _ A B C D E F G H I J K L M N O P Q R
S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
[Reset] button
[Rec] button
Delete a character.
Inserts a space.
4. When you have finished assigning the name,
simultaneously press [Registration] button and the [Media]
button once again.
The Registration set in the ATELIER’s internal memory has now been named.
To return to the basic screen, press the [Display/Exit] button.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
Saving Registration Sets
With the settings of Registration buttons [1]–[8] considered as one set, you
can store the registration set to USB memory or User memory. We recommend
that complex panel settings or Registrations you wish to keep be saved on USB
memory. Furthermore, when you save registrations created on the ATELIER to
USB memory, you can call up their settings on other ATELIER Series instruments
and use the registrations the same way.
1. Connect your USB memory to the external memory
connector.
If you want to save registration
data to a floppy disk, connect
the floppy disk drive to the
external memory connector.
Into the floppy disk drive, insert
a floppy disk that was
2. Press the [Registration] button to make the indicator light.
The Registration select screen appears.
formatted by the ATELIER.
3. Press the [Media] button to select the desired media.
If you want to save the registration to USB memory, select “Ext Memory.”
If you want to save the registration to floppy disk, select “Disk.”
If you want to save the registration to user memory, select “User.”
4. Press the Value [-] and [+] buttons to select the save-
destination number.
Numbers which have not been used in the Saving operation will be displayed
as “- - - - - - - - - - - -.”
To cancel the operation, press the [Registration] button.
fig.07-10
5. Press the [Save] button.
6. Press the Value [-] and [+] buttons to select the format in
which the data will be saved.
Save formats that can be used with the AT-100 and AT-300
When saved in this format, the data can also be used by AT-
S Series, AT-900, AT-900C AT-800, AT-45 and AT-15
ORIGINAL
devices.
R-SERIES
Save formats that can be used with AT-R Series devices
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
7. Press the [Save] button to execute the save operation.
NOTE
Saving of the registration data will begin.
Never remove the USB memory
or turn off the power while the
operation is in progress. Doing
so will damage the ATELIER’s
internal memory or USB
When saving ends, the “- - - - - - - - - - - -” in the screen will change to the
registration name that you saved.
fig.07-11
memory, making it unusable.
If you’ve named the registration (p. 58), it will be saved with that name.
If the following screen appears
If you select a number at which a registration has already been saved and
press the [Save] button, the following screen appears.
If you wish to update the contents of the Registration data
1. Press the [Rec] button.
The Registration will be rewritten.
If you wish to save new data instead of updating the registration
1. Press the [Reset] button to cancel the procedure.
Rewriting of the Registration will be canceled.
2. Press the Value [-] [+] buttons to select a number for which
“- - - - - - - - - - - -” is displayed on the upper right of the
screen.
3. Press the [Save] button to save the Registration set.
When saving is complete, the saved registration name will be displayed.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
Loading Previously Saved Registration Sets Into the ATELIER
Here’s how to recall a previously saved Registration set from the User memory
or USB memory into the memory of the ATELIER. Registrations can be selected
in the following two ways.
NOTE
Be aware that when you load
Loading a Set of Registrations
Registrations from a USB
memory or user memory, the
Registrations that were
previously in internal memory
will be lost. It is a good idea to
save important Registrations to
USB memory or user memory
(p. 60).
You can load a “set” (a collection of settings for Registration buttons [1]–[8])
from Floppy disk, USB memory or User memory.
Loading an Individual Registration
Recall the settings of one of the Registration [1]–[8] buttons.
Loading a Set of Registrations
1. If you want to load a registration from USB memory,
connect your USB memory to the external memory
connector.
If you want to load a
registration from a floppy disk,
connect the floppy disk drive to
the external memory connector,
and insert the floppy disk
containing the registration into
the floppy disk drive.
2. Press the [Registration] button to make the indicator light.
The Registration select screen appears.
3. Press the [Media] button to select the desired media.
If you want to load from the registration of USB memory, select “Ext Memory.”
If you want to load from the registration of floppy disk, select “Disk.”
If you want to load from the registration of user memory, select “User.”
4. Press the Value [-] or [+] button to select the Registration
that you wish to load into internal memory.
To cancel the procedure, press the [Registration] button.
5. Press the [Load] button to execute loading.
When loading is complete, the Registration Select screen reappears.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
Loading an Individual Registration
1. If you want to load a registration from USB memory,
connect your USB memory to the external memory
connector.
If you want to load a
registration from a floppy disk,
connect the floppy disk drive to
the external memory connector,
and insert the floppy disk
containing the registration into
the floppy disk drive.
2. Press the [Registration] button to make the indicator light.
The Registration Select screen appears.
3. Press the [Media] button to select the desired media.
If you want to load from the registration of USB memory, select “Ext Memory.”
If you want to load from the registration of floppy disk, select “Disk.”
If you want to load from the registration of user memory, select “User.”
4. Press the Value [-] or [+] button to select the Registration
that you wish to load into internal memory.
5. Press the [Utility] button.
6. Press the Value [-] or [+] button to specify the Registration
button number to be loaded.
fig.07-14
To cancel the operation, press the [Utility] button.
7. Press the [Rec] button.
8. Press the Value [-] or [+] button to specify the storage-
destination Registration.
fig.07-15
9. Press the [Rec] button.
The following display appears.
fig.07-16
To cancel the procedure, press the [Reset] button.
10. Press the [Rec] button once again.
When the Registration has been loaded, the Registration Load screen will
reappear.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a Set of Registrations
Here’s how to delete a Registration set that was saved to a USB memory, User
memory (p. 41), or floppy disk.
1. Prepare the registration that you want to delete.
If you want to delete
If you want to delete registration data from the USB memory, connect the USB
memory to the external memory connector.
registration data from the
floppy disk, connect the floppy
disk drive to the external
memory connector. Into the
floppy disk drive, insert a
floppy disk.
2. Press the [Registration] button to make the indicator light.
The Registration select screen appears.
3. Press the [Media] button to select the desired media.
If you want to delete from the registration to USB memory, select “Ext
Memory.”
If you want to delete from the registration to floppy disk, select “Disk.”
If you want to delete from the registration to user memory, select “User.”
4. Press the Value [-] and [+] buttons to select the registration
that you wish to delete.
5. Simultaneously press the [Load] button and [Save] button.
The following display appears.
fig.07-08
To cancel the procedure, press the [Reset] button.
6. If you are sure that you wish to delete the data, press the
[Rec] button.
NOTE
Never remove the USB memory
or turn off the power while the
operation is in progress. Doing
so will damage the ATELIER’s
internal memory or USB
When a registration is deleted, the deleted registration name will change to
“- - - - - - - - - - - -.”
fig.07-18
memory, making it unusable.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Registration Buttons
Copying Registrations
Registrations from USB memory or floppy disk can be copied to user memory.
If a registration saved in USB memory or on a floppy disk is stored in user
memory, the stored registration data will not disappear even when you turn
off the power. It is convenient to load frequently-used registration into User
memory.
Registrations saved in user memory can also be copied to USB memory (p.
66).
Copying Registration from USB Memory to User
Memory
1. Connect the USB memory to the external memory
If you want to copy registration
from floppy disk, connect the
floppy disk drive to the external
memory connector.
connector.
2. Press the [Utility] button.
3. Press the Menu [ ] and [ ] buttons to select “Media
Utility.”
fig.02-09.eps
4. Press the [Rec] button.
5. Press the Menu [ ] and [ ] buttons to select “Copy
Registration.”
fig.02-10.eps
6. Press the [Rec] button.
7. Press the [Media] button to select the media (the location of
the Registration you want to copy).
If you want to copy a Registration from USB memory, select “Ext Memory.”
If you want to copy a Registration from floppy disk, select “Disk.”
65
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press the Value [-] and [+] buttons to select the Registration
you want to copy.
NOTE
Never remove the USB memory
or turn off the power while the
registration data is being
copied from USB memory into
the ATELIER. If you do so, the
registration data will not be
loaded into the ATELIER, and
malfunctions could result. After
returning the registration stored
in the user memory to the
factory settings (p. 119), reload
the registration from USB
memory.
9. Press the [Rec] button.
10. Press the Value [-] and [+] buttons to select the copy-
destination number.
To cancel the procedure, press the [Display/Exit] button.
11. Press the [Rec] button to copy the Registration.
If you select a number in which a Registration is already saved, a screen like
the following appears.
If you want to delete the previously saved Registration and overwrite it with
the Registration you’re newly saving, Press the [Rec] button.
If you don’t want to delete the previously saved Registration, Press the [Reset]
Button, then select a number at which no Registration has been saved, and
copy the Registration to that number.
You can return only the user
memory to the factory settings.
Refer to “Restoring the User
Memory to the Original Factory
Settings (User Memory
Reset)”(p. 119).
To return to the basic screen, press the [Utility] button.
Copying Registration from User Memory to USB
Memory
You can copy Registration from user memory to USB memory.
To do so, press the [Media] button in step 7 (above) to choose “User.” In this
state, you’ll be copying Registration from user memory to USB memory.
The rest of the procedure is the same as when copying Registration from USB
memory to user memory.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Performance Functions
Ò
Transposing to a Different Key (Key Transpose)
You can transpose the key of a performance without having to shift the
position of your fingers on the keyboard. This feature is called “Key
Transpose.”
For example: you may play in the familiar C major scale while your music will
sound in any key of your choice.
fig.06-01
1. Press the Transpose [-] and [+] buttons.
Each press of the Transpose [-] or [+] button transposes the key a semitone.
The transpose value is displayed in the screen.
Acceptable values range from A to G (in semitone steps).
fig.06-03
If the pitch is transposed (something other than C), the indicator of one of the
Transpose buttons, either [-] [+], will be lit. If the pitch is not transposed (i.e.,
the key is C), the indicator of both the Transpose [-] and [+] buttons will be
extinguished.
By pressing the Transpose [-]
and [+] buttons simultaneously,
you can restore the default
setting “C.”
You can change the timing at
which the transposition settings
saved in a Registration will be
recalled. For details refer to
“Registration Transpose Update
(Trans. Update)” (p. 109).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Performance Functions
Adding Decay to the Sound (Damper Pedal)
NOTE
You can depress the damper pedal to add reverberation to notes played on
the lower manual.
Decay cannot be added to the
Solo voices.
While you continue depressing the damper pedal, notes will be sustained
even if you release the keys.
fig.06-04
Decay can not be applied to
Pedal Bass voices played on
the Lower keyboard (when the
Pedal [To Lower] button
indicator is lit or Bass Split
function is ON).
Using the Foot Switch
On each side of the expression pedal are two Foot Switches. Different
functions are assigned to each of these two foot switches.
fig.06-07
You can also change the
function assigned to the Foot
Switch.
Please refer to “Changing the
Function of the Foot Switch” (p.
69).
With the factory settings, the following functions are assigned to the left and
right Foot Switches.
Right Foot Switch
Switch the Rotary effect between Fast/Slow.
NOTE
Glide (an effect by which the pitch is lowered by a
semitone while the foot switch is pressed, and is
returned to what is originally was when you release
your foot).
Glide is not applied to the
Left Foot Switch
Press the right Foot Switch toward the right.
If Rotary is turned on, the Rotary effect will switch between “Fast” and “Slow”
each time you press the Right Foot Switch.
You can store functions to be
assigned to the foot switch to
individual Registration buttons
(p. 69).
Press the left Foot Switch toward the left.
While you are pressing the Foot Switch, the pitch will be temporarily lowered.
When you release the Left Foot Switch, the pitch will return to normal.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Performance Functions
Setting
Descriptions
Changing the Function of the Foot
Switch
You can select any of the following functions and assign them
to either Foot Switch on the right or left side of the Expression
Pedal.
INTRO/ENDING
Play an Intro or Ending.
Switches the Variation button. Each
time you press the foot switch, the
Variation number will increment.
VARIATION UP
Switches the Variation button. Each
time you press the foot switch, the
Variation number will decrement.
1. Press the [Utility] button.
VARIATION DOWN
VARIATION ALT
2. Press the Menu [
] and [
] buttons to
Switches the Variation button. If the
Variation [1] button or [3] button is
selected, this will switch between the
Variation [1] and [3] buttons. If the
Variation [2] button or [4] button is
selected, this will switch between the
Variation [2] and [4] buttons.
select “L Foot Switch” or “R Foot Switch.”
ig.12-09
FILL IN
BREAK
Adds a fill-in.
ig.12-09
Stop the Rhythm for one measure
(break).
Notes played on the Upper
keyboard will be sustained only
while you continue pressing the Foot
Switch.
DAMPER OF UPPER
3. Press the Value [-] and [+] buttons to set the
Decay cannot be added to
NOTE
function to be assigned to the foot switch.
the Solo voices.
To return to the basic screen, press the [Utility] button.
Notes played on the Lower keyboard
will be sustained only while you
continue pressing the Foot Switch.
Setting
Descriptions
DAMPER OF LOWER
OFF
ROTARY FAST/
SLOW
Switch the Rotary speed between
“FAST” and “SLOW.”
Decay cannot be added to
the Solo voices.
NOTE
While the Foot Switch is pressed, the
pitch will temporarily be lowered,
and will gradually return to normal
when you release the Foot Switch.
Glide effect is added to the voice of
all the sections being played on
Upper keyboard.
Turns the foot switch function off.
If the Utility menu “Registration Shift” setting is
“RIGHT”, “LEFT” or “RIGHT+LoadNext“, the Foot
Switch will be dedicated to switching through the
Registrations, and the “R Foot Switch” or “L Foot
Switch” setting will be ignored.
NOTE
GLIDE
Glide is not applied to the
vintage organ.
NOTE
The Leading Bass function (p. 49) will
operate only while you continue
pressing the Foot Switch.
LEADING BASS
RHYTHM START/
STOP
Start/Stop the Rhythm.
The same function as the Composer
[Play/Stop] button. Each time you
press the Foot Switch, the
performance data will play back or
stop.
COMP PLAY/STOP
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Performance Functions
Setting
Descriptions
Using the Foot Switch to Switch
Registrations (Registration Shift)
You can use the Foot Switch as a dedicated switch for
selecting Registrations in order. The registration will be
switched each time you press the foot switch.
The right foot switch is dedicated to switching
registrations. The function assigned to the right
foot switch cannot be used.
Selecting the Registration [8] button and
pressing the right foot switch activates the Load
Next function, calling up the next registration
saved to the USB memory, user memory, or
floppy disk. The Registration Load window
appears in the display. When you then press
the right foot switch again, the Registration Set
is confirmed, and the Registration [1] button is
selected.
The Registration Shift settings are stored to each
individual Registration Set. When “RIGHT + Load
Next” is assigned to the foot switch and the Load
RIGHT +
Load Next
NOTE
Next function is used to switch Registration Sets saved
to a USB memory or floppy disk, set the Registration
Shift setting to “RIGHT + Load Next” for all saved
Registrations.
Example:
1→2→3...→8 →Load Next→
(Next Registration) 1
1. Press the [Utility] button.
What is “Load Next”?
2. Press the Menu [
] and [
select “Registration Shift.”
] buttons to
You can use the Load Next function to call up Registrations in
the order saved to the USB memory, user memory, or floppy
disk. When you will be performing live, you can save
registration sets to USB memory, user memory, or floppy disk
in the order in which you will be performing. Then while you
perform, you can recall the next registration set easily and
smoothly.
To return to the basic screen, press the [Utility] button.
3. Press the Value [-] and [+] buttons to change
the setting (OFF/RIGHT/LEFT/RIGHT + Load
Next).
This setting remains stored in memory even while the
power is turned off.
Setting
OFF
Descriptions
You can use a function assigned to the foot
switch.
The right foot switch is dedicated to switching
registrations.
The function assigned to the right foot switch
cannot be used.
RIGHT
The left foot switch is dedicated to switching
registrations.
The function assigned to the left foot switch
cannot be used.
LEFT
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Performance Functions
Adjusting the Overall Volume Using an Expression Pedal
You can adjust the entire volume using an Expression Pedal. When you
depress the Expression Pedal, the volume increases. The volume decreases as
you tilt the pedal back.
Likewise you can specify
whether the Expression Pedal
will or will not control the
volume during the playback of
recorded music data (p. 107).
fig.06-03
Decrease
the volume
Increase
the volume
Using the expression pedal enables you to give your performances even richer
musical expressiveness.
You can specify whether the
expression pedal will function
when playing back
performance data that was
recorded on the Atelier
series(p. 107).
The expression pedal features the following special characteristics:
• Completely releasing the expression pedal does not lower the volume to
zero. If you do want to turn down the volume completely, set the [Master
Volume] knob to the Min (Minimum) position.
• Even as you release your foot from the expression pedal and lower the
volume, the lower-range portion will linger on. This provides a natural-
sounding resonance.
• When an Active Expression voice is selected, the expression pedal can be
used to produce changes in the voice (p. 35).
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
The ATELIER allows you to apply various effects to the sounds you play from
the keyboard.
Adding Harmony to a Melody (Harmony Intelligence)
Harmony appropriate for the chord you play in the lower keyboard can be
added to the highest note played in the upper keyboard. This function is called
“Harmony Intelligence.”
When you press the [Harmony Intelligence] button, the voice most suitable for
the selected harmony intelligence will be selected automatically.
1. Press the [Harmony Intelligence] button (indicator lights).
Each time you press a [Harmony Intelligence] button, the indicator will
alternate between ON (lit) and OFF.
fig.04-01
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Changing the Type of Harmony Intelligence
The AT-300 provides twelve types of harmony intelligence, and the AT-100
provides eight types.
When you press the [Harmony Intelligence] button, the most appropriate
voice(s) will be automatically set.
The manner in which notes will sound also depends on the Harmony type.
1. Press the [Harmony Intelligence] button (indicator lights).
2. While the Harmony Intelligence name is shown in the
display screen, use the Value [-] or [+] button to select the
Harmony Intelligence.
The indicator of the [Harmony Intelligence] button will blink.
To cancel the procedure, press the [Display/Exit] button.
3. Once again, press the [Harmony Intelligence] button.
You can also play the upper
manual to confirm the type of
the Harmony Intelligence.
The indicator of the [Harmony Intelligence] button will light, and the Harmony
Intelligence is confirmed.
Harmony Intelligence types:
Number of
notes of the
harmony
AT-
AT-
Type
Solo Voice
Upper Voice
300 100
BIG BAND
Trumpet
Flugel Horn
Strings 5
5
4
3
2
3
4
3
2
5
4
4
3
o
o
o
o
o
o
o
o
o
o
o
o
o
o
The number of notes of the
harmony will depend on the
Harmony Intelligence type.
STRINGS
Strings 1
TRADITIONAL*
HARP
Currently Selected Tone
o
—
Harp
o
COMBO
Clarinet
Jazz Scat
Celesta
Trombone
Jazz Scat
Theater Or.1
—
o
Harp-type harmony intelligence
will not sound the keys you
play. Use your left hand to play
a chord in the lower keyboard
and use your right hand to play
a glissando on the upper
JAZZ SCAT
BROADWAY
OCTAVE 1*
BIG BAND*
STRINGS*
—
o
Currently Selected Tone
Currently Selected Tone
Currently Selected Tone
Currently Selected Tone
Currently Selected Tone
o
o
keyboard, and a beautiful harp
glissando will be produced.
JAZZ SCAT*
BROADWAY*
o
—
Harmonies are added only to the Upper voice.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Adding Modulation to the Sound (Rotary Effect)
Rotary is an effect which simulates the sound of rotating speakers.
There is a choice of two settings: Fast and Slow.
fig.05-06.eps
NOTE
1. Select the voice to which you wish to apply the Rotary
For more on the tones to which
the Rotary effect can be
applied, refer to “Voice &
Rhythm List” (Appendix:
separate booklet).
effect.
2. Press the Rotary Sound [On/Off] button (confirm that its
indicator is lit).
The Rotary effect will be applied to the voice.
3. Press the Rotary Sound [Fast/Slow] button to switch
between Rotary Fast (Lit) and Rotary Slow (Unlit).
Rotary Sound
Effect
[Fast/Slow] button
You can assign the Rotary
Sound [Fast/Slow] button
function to the foot switches
located on each side of the
Expression Pedal (p. 69).
The effect obtained is equivalent to speakers being
rapidly rotated.
Lit (Fast)
Unlit (Slow)
Effect simulating the slow rotation of speakers.
When you switch the rotary effect from “Fast” to “Slow,” the modulation will
slow down gradually, and when you switch from “Slow” to “Fast” the
modulation will speed up gradually.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Sustain Effect
Sustain allows you to add a Sustain effect or decay to each voice after the
keys are released. The Sustain effect can be added simultaneously to the
Upper (except the Solo Part), Lower, and Pedal Bass voices.
1. Press the [Utility] button.
NOTE
The Sustain effect will not be
applied to the Solo part and
vintage organ part voice.
2. Press the Menu [ ] and [ ] buttons to select the
“Sustain.”
3. Press the [Rec] button.
4. Press the Menu [ ] and [ ] buttons to select the desire
part.
Part
Upper, Lower, Pedal
5. Press the Value [-] and [+] buttons to switch ON or OFF.
The length of Sustain can be
modified independently for
each keyboard (p. 76).
To return to the basic screen, press the [Utility] button.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Changing the Sustain Length
The sustain length can be set independently (SHORT, MIDDLE (Medium) or
LONG) for the Upper and Lower keyboards and Bass Pedalboard. You can
make a separate setting for each keyboard.
1. Press the [Utility] button.
2. Press the Menu [ ] and [ ] buttons to select “Sustain.”
3. Press the [Rec] button.
4. Press the Menu [ ] and [ ] buttons to select “Length.”
fig.11-06
5. Press the Menu [ ] and [ ] buttons to select the part
whose sustain length you wish to adjust.
Part
Upper, Lower, Pedal
6. Press the Value [-] and [+] buttons to adjust the setting.
Settings
SHORT, MIDDLE, LONG
To return to the basic screen, press the [Utility] button.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Reverb Effect
Reverb is an effect that adds a sense of spaciousness to the sound, creating
the illusion of playing in a large or small concert hall, a large or small room,
a small club, etc.
fig.04-07
1. Press the Reverb [▲] or [▼] buttons to adjust the overall
Reverb amount.
When you press the Reverb [▲] button, additional Reverb is applied. Pressing
the Reverb [▼] button decreases the Reverb level.
When you press the Reverb [▲] [▼] buttons, the Reverb level will be shown
in the display.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Changing the Reverb Type
By changing the reverberations of the notes, you can enjoy the atmosphere of
performance in a wide variety of different locations.
1. Press the [Utility] button.
2. Press the Menu [ ] and [ ] buttons to select “Reverb.”
3. Press the [Rec] button.
4. Press the Menu [ ] and [ ] buttons to select “Reverb
Type.”
fig.11-04
5. Press the Value [-] and [+] buttons to select a Reverb type.
Type
Descriptions
Reverberation of a small room
Reverberation of a small club
ROOM 1
ROOM 2
ROOM 3
HALL 1
Reverberation of a large room
Reverberation of a large concert hall
Reverberation of a small concert hall
HALL 2
SMALL CHURCH The reverberation of a small church
LARGE CHURCH The reverberation of a large church
CATHEDRAL
PLATE
The reverberation of a cathedral
A bright, metallic Reverberation
DELAY
An echo-like sound repeated several times
Similarly to the above but where the sound is
panned between the left and right speakers
PAN DELAY
To return to the basic screen, press the [Utility] button.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Changing the Wall Type
By changing the type of reverb you can experience the feeling of performing in various
different locations, and by changing the Wall Type (wall material) you can make
further adjustments to the way in which reverberation occurs.
1. Press the [Utility] button.
2. Press the Menu [ ] and [ ] buttons to select “Reverb.”
3. Press the [Rec] button.
4. Press the Menu [ ] and [ ] buttons to select “Wall
Type.”
fig.11-04
5. Press the Value [-] and [+] buttons to select a Wall type.
Type
DRAPERY
Descriptions
Pleated curtain
Carpet
CARPET
ACOUSTIC TILE
WOOD
Acoustical tile, sound-absorptive tile
Wood
BRICK
Brick
PLASTER
Plaster
CONCRETE BLOCK
MARBLE
Concrete block
Marble
To return to the basic screen, press the [Utility] button.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding Various Effects to a Voice
Changing the Depth of the Reverb
You can make independent settings for each Part.
1. Press the [Utility] button.
2. Press the Menu [ ] and [ ] buttons to select “Reverb.”
3. Press the [Rec] button.
4. Press the Menu [ ] and [ ] buttons to select “Depth.”
fig.11-05
5. Press the Menu [ ] and [ ] buttons to select the part
whose reverb depth you wish to adjust.
Part
Accomp (Automatic Accompaniment except Bass), Rhythm, Drums,
A.Bass (Bass part of Automatic Accompaniment), Pedal, Lower, Solo, Vintage
6. Press the Value [-] and [+] buttons to adjust the setting.
Settings
Descriptions
0 – 10
AUTO (Accomp, Rhythm, A.Bass)
Increasing the value will increase the amount
of reverb effect.
For the three Parts of the Accomp, Rhythm and A.Bass, you have the option of selecting
the “AUTO” setting. Parts for which “AUTO” is selected will be set to the Reverb Depth
that is most suitable for the Rhythm currently selected.
To return to the basic screen, press the [Utility] button.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Lower Keyboard Effectively
Making Effective Use of the Lower Keyboard
Since the lower keyboard of the ATELIER provides a generous 61 notes, you
can divide the keyboard into two or more sections and play solo voices, play
For example, the following applications are possible.
Using the Lower Keyboard to Play the Solo Voice
• Press the Solo [To Lower] button in the Solo section to Play the Solo voice to the Lower
keyboard (p. 84).
fig.06-01.eps
■
■
■
■
Drums/SFX
Bass
Lower
Solo
Playing Drum Sounds from the Entire Lower Keyboard
• Press the [Drums/SFX] button (p. 38).
fig.06-04.eps
■
■
■
■
Drums/SFX
Bass
Lower
Solo
Using the Lower Keyboard to Play the Bass Part by Hand
• “Bass Split” function is ON in the Pedal section to play the Pedal Bass voice from the Lower
keyboard (p. 86).
fig.06-02.eps
■
■
■
■
Drums/SFX
Bass
Lower
Solo
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Lower Keyboard to Play Drum Sounds and Solo Voice
• Press the [Drums/SFX] button (p. 38), and then press the Solo [To Lower] button (p. 84)
fig.06-01-2.eps
■
■
■
■
Drums/SFX
Bass
Solo
By changing the combination of voices that are played on the Lower
keyboard, and by changing the Solo Split Point (p. 85) and Bass Split Point
(p. 87), you can create the following types of setup.
fig.06-05.eps
fig.06-06.eps
■
■
■
■
Drums/SFX
Bass
Lower
Solo
fig.06-07.eps
■
■
■
■
Drums/SFX
Bass
Lower
Solo
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing the Solo Voice on the Lower Keyboard (Solo [To Lower] Button)
Normally, the solo voice will sound on the upper keyboard.
By using the Solo [To Lower] button, you can play the solo voice in the right-
hand side of the lower keyboard that includes the B4 key. The state in which
the keyboard is divided in this way is called “split,” and the location at which
the keyboard is divided to play the solo voice in the lower keyboard is called
the “Solo Split Point.”
fig.06-08_70
The key used for the solo split
point is included in the Solo
voice range.
NOTE
If the Solo [To Lower] is ON,
the Solo voice will not be heard
from the upper keyboard.
1. Select a Solo voice (p. 28).
2. Press the Solo [To Lower] button (indicator lights).
When you play the Lower keyboard, the Solo voice will sound in the range to
the right of the Solo Split Point.
You can change how the Solo
fig.06-09
Solo voice
Lower keyboard
You can layer the Solo voice
with the Lower voice so that
85).
Solo Split Point
3. To turn off the Solo split, press the Solo [To Lower] button
(indicator turns off).
The Solo voice will no longer sound in the Lower keyboard; the Solo voice will
now be played in the Upper keyboard.
You can adjust the Solo Split
Point (p. 85).
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing How the Solo Voice Responds
(Solo Mode)
Layering the Solo Voice and Lower Voice
(Solo To Lower Mode)
When the Solo voice is assigned to the Upper keyboard or
Lower keyboard, you can specify how the Solo voice will
respond when more than one key is pressed.
When the Solo voice is being played by the Lower keyboard
(i.e., when the Solo [To Lower] button is ON), you can specify
whether the Lower voice and the Solo voice will sound
together (layered), or will sound separately (split).
1. Press the [Utility] button.
1. Press the [Utility] button.
2. Press the Menu [
] and [
] buttons to
2. Press the Menu [
] and [
] buttons to
select “Solo Mode.”
select “Solo To Lower Mode” (Solo To Lower
Mode).
fig.12-05
3. Press the Value [-] and [+] buttons to change
the setting for Solo Mode.
3. Press the Value [-] and [+] buttons to switch the
Setting
Descriptions
“SPLIT” or “LAYER.”
The Solo voice will sound the highest note
that is played for the Solo part.
Setting
SPLIT
Descriptions
TOP NOTE
The parts will sound separately.
The Solo voice will sound the note that was
most recently played for the Solo part.
LAST NOTE
The Lower voice and Solo voice will sound
together.
LAYER
The Solo voice will sound all notes that are
played for the Solo part.
POLYPHONIC
To return to the basic screen, press the [Utility] button.
To return to the basic screen, press the [Utility] button.
Changing the Solo Split Point
This setting is used to determine the Solo Split Point (lower limit
of the playable range of the Solo voice) on the Lower
keyboard to any desired position.
1. Press the [Utility] button.
2. Press the Menu [
] and [
] buttons to
select “Solo Split Point.”
3. Press the Value [-] and [+] buttons to change
the Solo Split Point.
Settings
C2 – C7
By pressing the Value [-] and [+] buttons simultaneously, you
can restore the default setting (B 4).
To return to the basic screen, press the [Utility] button.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Lower Keyboard to Play the Bass Voice (Bass Split)
By using the “Bass Split” function you can play the bass voice in the left-hand
side (including C3) of the lower keyboard. The location at which the lower
keyboard is divided in this way, to play the pedal bass voice, is called the
“Bass Split Point.”
The bass split point is included
in the left-hand area of the
keyboard.
1. Select a Pedal Bass voice (p. 27).
2. Press the [Utility] button.
NOTE
It is not possible to select and
play both “Bass Split” function
and Pedal [To Lower] buttons
simultaneously.
3. Press the Menu [ ] and [ ] buttons to select “Bass Split.”
4. Use the Value [-] or [+] button to turn ”Bass Split” on.
You can adjust the Bass Split
Point (p. 87).
When you play the Lower keyboard, the Pedal Bass voice will sound in the
range to the left of (and including) the C3 note.
fig.06-16.eps
Pedal Bass
voice
Lower keyboard
NOTE
If the ”Bass Split” function is on,
the Pedal Bass voice will not be
heard from the Pedalboard. The
Pedal Bass voice will sound
from the Lower keyboard.
Bass Split Point
To return to the basic screen, press the [Utility] button.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Bass Split Point
You can assign the Bass Split Point (the highest key up to
which the Pedal Bass voice will sound), to any key of the
Lower keyboard.
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“Bass Split Point.”
3. Press the Value [-] and [+] buttons to modify
the Bass Split Point.
Setting
C2–C7
By pressing the Value [-] and [+] buttons simultaneously, you
can restore the default setting (C3).
To return to the basic screen, press the [Utility] button.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Lower Keyboard to Play the Bass Voice
(Pedal [To Lower] button)
By using the Pedal [To Lower] button, you can sound the Pedal Bass voice by
playing the root note (p. 132) of a chord on the Lower keyboard in the area
that is playing the Lower voice.
NOTE
If no portion of the Lower
keyboard is sounding the Lower
voice (the [Drums/SFX] button
is ON), the Pedal Bass voice
will not sound.
fig.05-08
NOTE
If the Pedal [To Lower] is ON,
the Pedal Bass voice will not be
heard from the Pedalboard.
1. Select a Pedal Bass voice (p. 27).
2. Press the Pedal [To Lower] button (indicator lit).
When you play a chord in the area of the Lower keyboard that sounds the
Lower voice, the Pedal Bass voice will also be heard and will play the root
note.
If the “Leading Bass” function is on (p. 49), the lowest note played in the lower
keyboard will sound the pedal bass voice.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Record and Playback Your Performance
The internal composer can record performances and play
back commercial SMF music files.
fig.08-01
What is a Track Button?
The recorded performance will be automatically assigned to the
three Track buttons according to the recorded part. You can
record or play back independently by specifying the desired
Track button; for example, when you wish to re-record a track.
You can record different kinds of performance data into each
track:
Button
Bass
Recorded performance
Button
Song
Description
Pedal Bass Voice Performance Data (Note)
Bass part of the Automatic Accompaniment
Lower Voice Performance Data (Note, Hold)
Upper Voice Performance Data (Note, Hold)
Solo Voice Performance Data (Note, Hold)
The Song Select screen appears in the
display.
Lower
The Registration Select screen appears in
the display.
Registration
Media
Solo
/Upper
Switches the media.
Button
Reset
Description
Returns you to the beginning of the song.
Starts and stops playback of the song.
After the [Rec] button has been pressed,
putting the composer in record standby
mode, recording then starts when the [Play/
Stop] is pressed.
Play/Stop
The ATELIER switches to record standby
mode.
and the [Play/Stop] button flashes.
Rec
Bwd
Fwd
Rewinds the song.
Fast forwards the song.
More information about the track assignments when playing
commercial SMF music files, please refer to “Silencing a
Specific Track (Track Mute)” (p. 113).
If you wish to erase all the recorded data and record new
performance data, use the editing function “Erase” (erase
performance data) to erase the data (p. 94).
89
Download from Www.Somanuals.com. All Manuals Search And Download.
To play back only one song
Playing Back Performance
Songs Stored on USB Memory
and SMF Music Files
1. Prepare the song that you want to play back.
If you want to play a song from USB memory, connect it
to the external memory connector.
If you want to play a song from floppy disk, connect the
floppy disk drive to the external memory connector, and
insert a floppy disk into the drive.
In addition to playing back the music you recorded on the
instrument and saved to a USB memory, ATELIER also lets you
enjoy a wide variety of commercially available song files,
such as defined below.
2. Press the [Song] button (confirm that its
indicator is lit).
The Song Select screen appears.
SMF Music Files
SMF (Standard MIDI File) is a data format that was
created in order to standardize music data formats
between manufacturers. Collections of songs in SMF
music data are commercially available in a wide range of
styles for enjoyment, as accompaniment for practicing
musical instruments, and for karaoke.
3. Press the [Media] button to select the desired
If you want to purchase SMF music data, you can contact
the dealer where you purchased the ATELIER.
media.
If you want to play a song from USB memory, choose
“Ext Memory.” If you want to play a song from floppy
disk, choose “Disk.”
4. Press the Value [-] and [+] button to select the
song that you wish to play back.
5. Press the [Play/Stop] button to start playback.
4
Playback of the performance data begins.
6. To stop playback, press the [Play/Stop]
3
button.
2
Playing back all performance data
1. Prepare the song that you want to play back.
If you want to play a song from USB memory, connect it
to the external memory connector.
If you want to play a song from floppy disk, connect the
floppy disk drive to the external memory connector, and
insert a floppy disk into the drive.
5,6
2. While holding down the [Song] button, press
the [Play/Stop] button.
All performance data saved on the USB memory or
floppy disk will be played consecutively.
3. To stop playback, press the [Play/Stop]
button.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Silencing a Specific Track
(Track Mute)
Recording a Performance
You can record the performance that you play. You can also
record your performance while playing rhythms or automatic
The indicators for Track button in which performances were
recorded will be lit. By turning off these Track button
indicators, you can temporarily silence the sound. This is
referred to as “Track Mute.”
accompaniment.
fig.07-12.eps
If you want to play back a song from USB memory, connect
your USB memory to the external memory connector before
you continue.
If you want to play back a song from floppy disk, connect your
floppy disk drive to the external memory connector, and insert
the floppy disk.
3, 4 2
1. Select the panel settings needed for recording
the performance.
2. Enter the recording standby mode by pressing
the [Rec] button.
The [Rec] button indicator will light, and the [Play/Stop]
button will blink.
1. Press the Track button whose indicator is lit to
3. Press the [Play/Stop] button to start recording.
turn the light off.
When you press [Play/Stop] button, the metronome will
sound a two-measure count, and then recording will
begin.
The track whose indicator was turned off will be muted
(silenced).
If you wish to use Rhythm and Automatic Accompaniment as
you record, press the [Start/Stop] button (p. 42) instead of
the [Play/Stop] button to begin recording. Also, if the
Synchro Start is ON, recording will begin the instant you
play the Lower keyboard.
2. Press the Track button once again (indicator
lights).
The part that had been muted will return to normal and
will be heard.
4. Press the [Play/Stop] button when you have
Assignments to the Track Button When
Playing Back Commercial SMF Music Files
completed your recording.
The Track indicator where a performance song is
recorded will light.
Button
When you press the [Intro/Ending] button or [Start/Stop]
Automatic Accompaniment, the Rhythm performance
and Automatic Accompaniment will stop. However, the
recording itself will continue. Press the [Play/Stop]
button to stop recording.
[Bass]
2
[Lower]
3
[Solo/Upper]
1, 4
You can also change the Track Mute Settings in the Utility
menu (p. 113). You can individually mute the rhythm track
and accompaniment track as well as the Upper Track and
Solo Track. You can also mute the Control Track (for the
expression pedal and panel controls) (p. 113).
The Play and Stop functions can both be assigned to one of
the foot switches located on each side of the Expression
Pedal (p. 69).
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
Playing Back a Performance
Song
If you press the [Rec] button when a song has been selected
from the USB memory or floppy disk, the selected song will be
completely loaded into the ATELIER and the Composer will
enter into the recording standby mode. To record a new song,
Here’s how to play back a performance you’ve recorded.
use the following procedure.
fig.08-06
ig.07-12-2.eps
1 2,3
1. Press the [Reset] button.
1. Press the [Rec] button to cancel recording
The location at which playback will start will return to the
beginning of the first measure (bar).
standby.
If you wish to begin playback from the middle of the
song, press the [Bwd] button or [Fwd] button to move to
the measure from which you wish to begin playback.
2. Disconnect the external media.
If you’ve connected USB memory, disconnect the USB
memory from the external memory connector. If you’re
using a floppy disk, remove the floppy disk from the disk
drive.
2. Press the [Play/Stop] button to start playback.
will stop automatically.
3. Delete the performance data (p. 94).
Re-record your performance.
f
Stop] button.
If the following screen appears
The [Play/Stop] function can be assigned to the foot switch
(p. 69).
fig.E-30.eps
You can specify whether or not the Expression Pedal will
affect the playback and what you play while Atelier music
data is being played back (p. 107).
If you use the Rhythm or Automatic Accompaniment
immediately after having loaded and played back a song
other than an Atelier performance song, such as SMF’s, etc.,
the playback may not sound right (the voices may have
changed, etc.) To prevent this from happening, press the
[Reset] button before playback.
When recording was automatically canceled because
the memory limit was reached.
NOTE
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Add a Count Sound to Match
the Timing (Count In)
Recording Each Part Separately
In this method, each part (track button) is recorded one after
another: first the bass part, then the Lower part, etc. If there
are any previously recorded performances, you can listen to
them as you record additional parts.
In cases such as when you want to perform in time with a
song, you can have a count sound played before playback of
the song begins, allowing you to synchronize your own
performance with the song.
Playing back a song after playing the count sound is called
“Count In.”
4
5,6 3 2
1. Select the panel settings needed for recording
the performance.
2. Press the [Bwd] button or the [Fwd] button to
select the desired measure (bar) when you
start recording.
1
1. Hold down the [Reset] button and press the
If you wish to start recording from the beginning of the
song, press the [Reset] button.
[Play/Stop] button.
The metronome will play two measures (bars) of count-in
before recording begins.
3. Press the [Rec] button to enter recording-
standby mode.
The [Rec] button indicator will light, and the [Play/Stop]
button and the unrecorded track buttons will blink. The
track buttons that are already recorded will light.
4. Press the button of the track you want to
record, so it’s blinking.
The existing performance data in the specified track will
be erased as recording takes place.
When the button for a track lights steadily, it means it won’t
be recorded.
NOTE
5. Press the [Play/Stop] button to start recording.
When you press [Play/Stop] button, the metronome will
sound a two-measure count, and then recording will
begin.
As you listen to the performance song previously
recorded, record the Part into a new Track.
6. Press [Stop] button to stop recording.
The track button for which performance data has been
recorded will be lit.
7. Repeat steps 2–6 to record each part.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Re-Recording
Erasing a Performance Song
You can record over recorded performance data.
If you wish to discard your recording and re-record from the
beginning, or if you wish to record a new performance, you
must erase the previously-recorded data.
3
2
1
4,5 2 1
1. Press the [Bwd] button or the [Fwd] button to
select the desired measure (bar) when you
start recording.
If you wish to start recording from the beginning of the
song, press the [Reset] button.
2. Press the [Rec] button to enter recording-
standby mode.
The [Rec] button indicator will light, and the [Play/Stop]
button and the unrecorded track buttons will blink. The
track buttons that are already recorded will light.
3
1. Press the [Display/Exit] button a number of
times to access the composer screen.
3. Press the button of the track you want to
record, so it’s blinking.
The existing performance data in the specified track will
be erased as recording takes place.
When the button for a track lights steadily, it means it won’t
be recorded.
NOTE
4. Press the [Play/Stop] button to start recording.
When you press [Play/Stop] button, the metronome will
sound a two-measure count, and then recording will
begin.
2. Press the [Load] and [Save] buttons
simultaneously.
The following message, asking you to confirm your
choice, will be displayed.
As you listen to the performance song previously
recorded, record the Part into a new Track.
fig.08-10
5. Press [Play/Stop] button to stop recording.
The track button for which performance data has been
recorded will be lit.
If you wish to re-record with different settings for voices,
re-record again. If the Control track still contains data from
To cancel the procedure, press the [Reset] button.
NOTE
before you re-recorded, the volume or sounds may change
during playback.
3. If you are sure that you wish to erase the
song, press the [Rec] button.
If you wish to keep the existing Expression Pedal data, and
record only the panel operations, you can make settings to
prevent the operation of the Expression Pedal from being
recorded (p. 107).
NOTE
94
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press the Menu [
] or [
] button to move
the cursor, and press the Value [-] and [+]
buttons to select a character.
The following characters can be selected when changing
a name:
Changing the Name of a
Performance Song (Rename)
A name is automatically assigned to a performance song that
you record. However, at some point you may wish to change
the name to something more meaningful.
space ! “ # % & ’ ( ) * + , - . / : ; = ? ^ _ A B C D E F
G H I J K L M N O P Q R S T U V W X Y Z a b c d e f
g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9
3
Press the [Reset] button.
Press the [Rec] button.
Delete a character.
Insert a space.
4. To confirm the new name, simultaneously
press the [Registration] and [Media] buttons
once again.
The new name is now inserted.
3
1
You cannot directly change or edit the name of a
performance song stored on a USB memory or floppy disk.
NOTE
The song must first be loaded (p. 97) into the instrument,
edited, and then saved to USB memory or floppy disk
again.
2,4
1. Press the [Display/Exit] button a number of
times to access the composer screen.
2. Press the [Registration] and [Media] buttons
simultaneously.
fig.08-10
Press the [Load] and [Save] buttons simultaneously.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press the [Media] button to select the media.
Select “Ext Memory” to save the data in USB memory,
select “Disk” to save it on a floppy disk, or “Favorites” to
save it in user memory.
Saving Performance Songs
The performance data that you recorded will disappear when
the power of the ATELIER is turned off. If you wish to keep the
performance data, you can save it on a USB memory, floppy
disk, or “Favorites” (internal memory).
4. Press the Value [-] and [+] buttons to select the
number of the save destination.
If the save destination contains no data, the screen will
If the recorded performance data has not been saved, the
indicate “- - - - - - - - - - - - .”
display will show the “
” symbol. This symbol will
fig.07-28-2.eps
disappear when you save the performance data.
fig.08-20
fig.08-19
5. Press the [Save] button.
2
3
5,7
4,6
6. Press the Value [-] or [+] button to select the
format.
You can select either “ORIGINAL” or “SMF” format.
Display
ORIGINAL Save data in ATELIER format
SMF
Description
Saving in SMF Format for ATELIER Sound Modules
SMF (Standard MIDI File) is a data format that was
created as a standardized way to exchange music
data between devices made by different
manufacturers.
1. Prepare to save the performance song.
If you want to save performance song to a USB memory,
connect the USB memory to the External memory
connector.
7. Press the [Save] button to confirm the format.
Saving of the performance data will begin.
If you want to save performance song to a floppy disk,
connect the floppy disk drive to the external memory
connector. Into the floppy disk drive, insert a floppy disk
that was formatted by the ATELIER.
2. Press the [Song] button (confirm that its
indicator is lit).
The Song select screen appears.
Never turn off the power while the operation is in progress.
Doing so will damage the ATELIER’s internal memory or USB
memory, making it unusable.
NOTE
NOTE
Performance data saved by the ATELIER format cannot be
played back properly by the sound generator of an
instrument that is not a member of the ATELIER series.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Saving performance data in SMF format (SMF) requires a
longer time than saving it in ATELIER format (Original).
NOTE
Loading Performance Songs
Into the ATELIER
If the following screen appears
If you select a number at which a performance data has already
To re-record a performance song that is stored on a USB
memory or floppy disk, you must first load that song into the
instrument.
been saved, the following screen appears.
fig.E-64-b.eps
If you wish to update the contents of the
performance data
2
3
4
5
1. Press the [Rec] button.
If you want to save your performance as new
data without overwriting the existing data
1. Press the [Reset] button to stop the Save
operation.
2. In the Song Select screen, select the number
that is displayed as “------------” (a number that
currently does not contain performance data).
3. Save the performance data.
1. Prepare the performance song.
When saving is complete, the saved performance name
will be displayed.
If you want to load performance song to a USB memory,
connect the USB memory to the External memory
connector. If you want to load performance song to a
floppy disk, connect the floppy disk drive to the external
memory connector. Into the floppy disk drive, insert a
floppy disk that was formatted by the ATELIER.
What is the SMF Format?
SMF (Standard MIDI File) is a data format that was
created to provide music files compatibility between
manufacturers.
2. Press the [Song] button (confirm that its
indicator is lit).
The Song Select screen appears.
3. Press the [Media] button to select the media.
If you want to load a song from USB memory, choose
“Ext Memory.” If you want to load a song from floppy
disk, choose “Disk.”
97
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press the Value [-] or [+] button to select the
performance song that you wish to load into
internal memory.
Deleting Performance Songs
Stored on “Favorites” or the
USB Memory
You can delete a performance song that was saved onto a
“Favorites,” USB memory, or floppy disk.
If you want to delete a song in USB memory, connect your
USB memory to the external memory connector before you
continue.
If you want to delete a song in floppy disk, connect the floppy
disk drive to the external memory connector, and insert a
floppy disk into the drive.
5. Press the [Load] button.
The selected performance data will be loaded into
internal memory.
If the following screen appears
If the performance song in the ATELIER has not been
saved to a USB memory or Favorites (User Memory), the
following message will appears.
fig.E-62.eps
4
1 3
2
If you wish to erase the performance song
1. Press the [Rec] button.
If you wish to erase the performance song
5
1. Press the [Reset] button to stop the Save
operation.
1. Press the [Song] button (confirm that its
indicator is lit).
Save the song to USB memory or a floppy disk (p. 96).
The Song Select Screen appears.
If loading is canceled because the memory limit has
been reached, the following message will be displayed:
fig.E-30.eps
2. Press the [Media] button to select the media.
If you want to delete a song from the “Favorites,” choose
“Favorites.”
If you want to delete a song from USB memory, choose
“Ext Memory.” If you want to delete a song from floppy
disk, choose “Disk.”
3. Press the Value [-] and [+] button to select the
performance data that you wish to delete.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press the [Load] button and [Save] buttons
simultaneously.
Layering a New Recording
onto SMF Music Files
The following message, asking you to confirm your
choice, will be displayed.
fig.08-10
You can load commercially available SMF music files into the
ATELIER, and record your own performance on top of it.
During recording, the data you’ve loaded will be played
back, while you record your performance.
To cancel the procedure, press the [Reset] button, and
you will return to the Song Select screen.
5. If you are sure that you wish to delete the
song, press the [Rec] button.
Never turn off the power while the operation is in progress.
Doing so will damage the ATELIER’s internal memory or USB
memory, making it unusable.
5
NOTE
2
3
4
6
10,11
8
1. Prepare the SMF music files.
If you’re using SMF music files from USB memory,
connect it to the external memory connector.
If you’re using SMF music files from a floppy disk,
connect the floppy disk drive to the external memory
connector, and insert the floppy disk.
2. Press the [Song] button (confirm that its
indicator is lit).
The Song Select screen appears.
3. Press the [Media] button to select the media.
If you want to play SMF music files from USB memory,
choose “Ext Memory.” If you want to play SMF music
files from floppy disk, choose “Disk.”
99
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press the Value [-] or [+] button to select the
SMF music files that you wish to load into
internal memory.
Using Song with a Different Tempo
Than That of the Performance Song
5. Press the [Load] button.
The selected performance data will be loaded into
internal memory.
6. Press the [Bwd] button and the [Fwd] buttons
to select the desired measure (bar) when you
start recording.
If you wish to start recording from the beginning of the
song, press the [Reset] button.
7. Select the panel settings needed for recording
the performance.
8. Press the [Rec] button to enter recording-
standby mode.
3
64
The [Rec] button indicator will light, and the [Play/Stop]
button and the unrecorded track buttons will blink. The
track buttons that are already recorded will light.
1. Prepare the performance data whose tempo
you want to change.
9. Press the button of the track you want to
record, so it’s blinking.
connect it to the external memory connector.
If you’re using performance data from a floppy disk,
connect the floppy disk drive to the external memory
connector, and insert the floppy disk.
The existing performance data in the specified track will
be erased as recording takes place.
When the button for a track lights steadily, it means it won’t
be recorded.
NOTE
10.Press the [Play/Stop] button to start recording.
into the ATELIER will play back.
2. Load the performance data into the ATELIER
(p. 97)
.
11.Press [Stop] button to stop recording.
The track button for which performance data has been
recorded will be lit.
3. Determine the tempo with the Tempo [ ] and
] buttons.
[
4. Hold down the panel [Reset] button and press
the [Rec] button.
The performance data you recorded can be saved on a USB
memory, “Favorites,” or floppy disk (p. 96).
The tempo of the performance data will change.
Commercially sold music files can also be loaded into the
ATELIER, but for reasons of copyright protection, cannot be
saved in SMF format.
NOTE
NOTE
The performances of Channel 2 in SMF music files are
deleted when pedal performances are recorded over again.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Press the Value [-] or [+] button to select the
performance song you want to copy.
Copying Performance Song
9. Press the [Rec] button.
Performance songs and SMF music files from USB memory or
floppy disk can be copied to “Favorites” (User memory).
If a performance song saved in USB memory or on a floppy
disk is stored in “Favorites,” the stored performance song will
not disappear even when you turn off the power. It is
convenient to load frequently-used performance song into
“Favorites.”
10.Press the Value [-] or [+] button to select the
copy-destination number.
Numbers for which a song name is shown already have
a song saved to them.
Performance songs saved in “Favorites” can also be copied to
11.Press the [Rec] button to copy the song.
USB memory or floppy disk.
The copying of the song to “Favorites” begins.
Once the song has been accommodated in memory, the
Media Utility screen will reappear.
Copying Performance Songs from USB
Memory to “Favorites”
Never remove the USB memory or turn off the power while
the performance song is being copied from USB memory
into the ATELIER. If you do so, the performance song will
1. Connecting the USB memory to the external
NOTE
memory connector.
not be loaded into the ATELIER, and malfunctions could
result.
If you want to copy performance song from floppy disk,
connect the floppy disk drive to the external memory
connector.
If you select a number in which a song is already saved,
a screen like the following will appear.
2. Press the [Utility] button.
3. Press the Menu [
] or [
] button to select
“Media Utility.”
If you want to delete the previously saved song and
overwrite it with the song you’re newly saving, press the
[Rec] button.
If you don’t want to delete the previously saved song,
press the [Reset] button, then select a number at which
no song has been saved, and copy the song to that
number.
4. Press the [Rec] button.
5. Press the Menu [
] or [
] button to select
Copying Performance Songs from
“Favorites” to USB Memory
“Copy Song.”
fig.02-10.eps
You can copy performance song from “Favorites” to USB
memory.
To do so, press the [Media] button in step 7 to choose
“Favorites.”, you’ll be copying performance song from
“Favorites” to USB memory.
6. Press the [Rec] button.
7. Press the [Media] button to select the media
(the location of the performance song you
want to copy).
If you want to copy a performance song from USB
memory, select “Ext Memory.”
If you want to copy a performance song from floppy
disk, select “Disk.”
The rest of the procedure is the same as when copying
performance song from USB memory to “Favorites.”
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a Folder in USB
Memory or User Memory
Changing the Name of a
Folder
You can create folders in a connected USB memory device or
in user memory.
Here’s how to rename a folder.
If you want to create a folder in USB memory, connect the USB
memory to the external memory connector.
1. In the Registration Select screen, select the
folder that you want to rename.
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“Media Utility.”
2. Press the [Registration] and [Media] buttons
simultaneously.
fig.08-10
3. Press the [Rec] button.
4. Press the Menu [
] or [
] button to select
“Create Folder.”
fig.02-10.eps
Press the [Load] and [Save] buttons simultaneously.
3. Press the Menu [
] and [
] buttons to
move the cursor, and press the Value [-] or [+]
button to select a character.
The following characters can be selected when changing
a name:
5. Press the [Rec] button.
_ A B C D E F G H I J K L M N O P Q R S T U V W X
memory, or “Ext Memory” if you want to create a folder
in USB memory.
Press the [Reset] button.
Press the [Rec] button.
Delete a character.
Inserts the letter “A.”
7. Press the [Rec] button.
4. To confirm the new name, simultaneously
press the [Registration] and [Media] buttons
once again.
8. Assign a name to the folder.
Rename the folder as described in “Changing the Name
of a Folder” (p. 102).
The new name is now inserted.
9. To confirm the new name, simultaneously
press the [Registration] and [Media] buttons
once again.
The name will be assigned to the newly created folder.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing with Sounds that Match the
Song (Recommended Tones)
Enjoying VIMA TUNES Songs
If you’re performing while listening to a CD-ROM produced for
VIMA (VIMA TUNES), you have the option of using
automatically selected tones that are appropriate for the mood
of the selected song.
When you select a song from a VIMA CD-ROM (VIMA
TUNES), three recommended tones will be selected
automatically.Using these three tones gives you an easy way
to perform using sounds that are appropriate for the mood of
the song.
Listening to a VIMA TUNES Song
You can connect a CD drive (commercially available) and
play back CD-ROM produced for VIMA TUNES (sold
separately). While playing a VIMA TUNES song, you can
play along using recommended tones.
VIMA TUNES
1. Select the song of VIMA CD-ROM.
VIMA TUNES is a Roland specification for music files that
contains image and lyric data, allowing you to enjoy songs
with lyrics and images simultaneously. When data bearing the
“VIMA TUNES” logo is played back on a device that bears
the same logo, lyrics can be shown on the screen of a
connected external display or television, letting you enjoy
karaoke or watch a slide show.
2. Press the [Utility] button.
3. Press the Menu [
] or [
] button to select
“VIMA TUNES.”
This instrument (AT-100/AT-300) is not able to play back
VIMA TUNES images.
NOTE
1. Connect a commercially available CD drive to
the external memory connector, and insert the
VIMA TUNES CD-ROM into the CD drive.
4. Press the [Rec] button.
5. Press the Menu [
] or [
] button to select
2. Press the [Song] button (confirm that its
indicator is lit).
“Recommend Tone.”
fig.02-10.eps
The Song Select screen appears.
6. Press the Value [-] or [+] button to select a
tone.
3. Press the [Media] button to select “CD.”
7. Press the [Utility] button to return to the basic
4. Press the Value [-] or [+] button to select the
screen.
song you want to play.
8. Press the [Play/Stop] button to start playing
5. Press the [Play/Stop] button to start playback.
back the song.
9. Play along with the song.
6. Press the [Play/Stop] button to stop playing
The tones you play will be suitable for the character of
the song.
back the song.
10.Press the [Play/Stop] button to stop playing
back the song.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying Karaoke with a Music CD
(Center Cancel)
You can minimize the vocal sounds of a commercially
available music CD, and sing the vocal part yourself. This is a
convenient way to enjoy karaoke or practice soloing with a
favorite music CD.
Listening to Songs from Music
CD
You can connect a CD drive to the ATELIER and use it to play
music CDs. This lets you perform or sing along with the
backing of a music CD.
completely.
You can’t copy music CD songs to “Favorites”.
NOTE
NOTE
It will take a certain amount of time until a music CD
can be selected.
1. Connect a commercially available CD drive to
NOTE
the external memory connector.
1. Connect a commercially available CD drive to
the external memory connector, and insert the
music CD into the CD drive.
2. Insert the music CD you want to use into the
CD drive, and select the song you want to sing
(p. 104).
3. Press the [Utility] button.
2. Press the [Song] button (confirm that its
indicator is lit).
4. Press the Menu [
] or [
] button to select
The Song select screen appears.
“VIMA TUNES.”
5. Press the [Rec] button.
3. Press the [Media] button to select “CD.”
6. Press the Menu [
] or [
] button to select
4. Press the Value [-] or [+] button to select the
“Melody.”
fig.02-10.eps
song you want to play.
5. Press the [Play/Stop] button to start playback.
6. To stop playback, press the [Play/Stop]
button.
7. Press the Value [-] or [+] button to select
“MUTE/C.CANCEL.“
you can press [Bwd] button or [Fwd] button to rewind or
fast-forward the playback.
The Center Cancel function is active.
8. Press the [Play/Stop] button to start playing
back the song.
When you play back the song, the sound of the melody
or vocal will be minimized.
This lets you perform the melody portion yourself.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
Transposing the Song to a Comfortable
Key for Singing
You can transpose the song to a key that is more comfortable
for you to sing.
If you or someone else will be singing along with a song, you
can change the key of the song so it’s appropriate for the
singer’s range.
If you select a different song, the playback transpose settings
1. Connect a commercially available CD drive to
the external memory connector.
2. Insert the music CD you want to use into the
CD drive, and select the song you want to sing
(p. 104).
3. Press the [Utility] button.
4. Press the Menu [
] and [
] buttons to
select “Playback Transpose.”
fig.02-10.eps
5. Each time you press the Value [-] and [+]
buttons, the key is changed by one semitone.
Value [-] button to lower the key, or Value [+] button to
raise the key.
This can be set in a range of -6–0–5 (semitone steps).
If you press the Value [-] and [+] button to select “0,” Key
Control will be turned off.
6. Press the [Play/Stop] button to start playing
back the song.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Various Other Settings
Adjusting How the Instrument
Responds
Changing the Pedalboard Polyphony
(Pedal Bass Mode)
You can set the Bass Pedalboard to play simultaneous multiple
notes or single notes only.
Adjusting the Initial Touch Sensitivity
(Initial Touch)
1. Press the [Utility] button.
Initial Touch is a function that translates the force used in
playing the keys into a directly proportional amount of volume.
This adjusts the amount of the Initial Touch effect applied.
2. Press the Menu [
] or [
] button to select
“PedalBass Mode.”
fig.12-06
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“Initial Touch.”
fig.12-03
3. Press the Value [-] or [+] button to switch the
Pedal Bass Mode “MONOPHONIC” or
“POLYPHONIC.”
Setting
MONOPHONIC
POLYPHONIC
Descriptions
3. Press the Menu [
] or [
] button to select
Only single notes can be played.
Multiple notes can be played.
“Upper“ or “Lower.”
Keyboard
To return to the basic screen, press the [Utility] button.
Upper, Lower
4. Press the Value [-] and [+] buttons to edit the
value.
Setting
Descriptions
Initial Touch is ON.
Striking the keys more forcefully will produce
correspondingly louder sounds.
The change in volume when the keys are
played forcefully increases as the value is
increased.
1–10
Initial Touch is off.
Volume remains constant regardless of how
hard you play.
OFF
To return to the basic screen, press the [Utility] button.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Function of the Expression Pedal
During Playback
Performance Function Settings
You can specify whether or not the Expression pedal will
function while ATELIER song files are being played back.
Changing the Function of the
Expression Pedal (Exp. Source)
1. Press the [Utility] button.
Specify how the Expression Pedal will function when your
performance is being recorded and when ATELIER song files
are being played back.
2. Press the Menu [
] or [
] button to select
“Exp. Source.”
fig.09-06
Function During Recording
Specify whether Expression Pedal operations will be recorded
or not while your performance is being recorded.
1. Press the [Utility] button.
3. Press the [Rec] button.
2. Press the Menu [
] or [
] button to select
“Exp. Source.”
4. Press the Menu [
] or [
] button to select
fig.09-06
“Playback.”
5. Press the Value [-] or [+] button to specify the
pedal function.
fig.09-08
3. Press the [Rec] button.
4. Press the Menu [
] or [
] button to select
“Recording.”
Setting
PEDAL+
Descriptions
5. Press the Value [-] or [+] button to specify the
Expression pedal will function.
Expression pedal recording within the
song file will also be effective.
pedal function.
fig.09-07
COMPOSER
Expression pedal will not function. The
Expression pedal recording within the
song file will be effective.
COMPOSER
Expression pedal will function. The
Expression Pedal recording within the
song file will be ignored.
PEDAL
Setting
Descriptions
Expression Pedal movements will be
recorded. The previous recording will be
erased as new songs are recorded.
PEDAL
To return to the basic screen, press the [Utility] button.
Expression Pedal movements will not be
recorded. The previous data will remain
without being erased.
COMPOSER
To return to the basic screen, press the [Utility] button.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Rhythm Settings
Changing the Sound of the Countdown
(Count Down Sound)
You can change the sound that is used for the count played at
the end of the intro with the Intro Countdown function (p. 45).
Preventing Rhythm Tempos from
Switching Automatically
(Auto Std Tempo)
You can prevent rhythm tempos from switching automatically
when you switch rhythms.
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“Count Down Sound.”
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“Auto Std Tempo” (Auto Standard Tempo).
3. Press the Value [-] or [+] button to select the
type of sound for Intro Count Down.
Setting
VOICE
STICK
Descriptions
Stick sound count
3. Press the Value [-] or [+] button to switch the
Auto Standard Tempo “ON” or “OFF.”
Setting
Descriptions
Switching the rhythm while the rhythm is
stopped automatically changes the tempo
settings to those in the new rhythm.
To return to the basic screen, press the [Utility] button.
ON
You can adjust the volume of the Count Sound, refer to
“Adjusting the Metronome Volume (Metronome Volume)” (p.
111).
When the rhythm is stopped, the tempo
settings are not changed automatically when
the rhythms are changed.
OFF
To return to the basic screen, press the [Utility] button.
This setting remains stored in memory even while power is
turned off.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration Settings
Registration Transpose Update
(Trans. Update)
You can specify how the transpose setting will be recalled
when you press a Registration [1] – [8] button.
Registration Arranger Update
(Arranger Update)
You can specify how the settings related to Rhythm
performances and Automatic Accompaniment will be recalled
when you press a Registration [1] – [8] button.
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
1. Press the [Utility] button.
“Trans. Update” (Transpose Update).
2. Press the Menu [
] or [
] button to select
“Arranger Update.”
fig.12-21
3. Press the Value [-] or [+] button to switch
between “DELAYED“ and “INSTANT.“
3. Press the Value [-] or [+] button to switch
Setting
Descriptions
between “DELAYED“ and “INSTANT.“
Transpose settings will be recalled when you
hold a Registration button for several
seconds.
DELAYED
Setting
Descriptions
Settings related to Rhythm performances and
Automatic Accompaniment will be recalled
when you hold a Registration button for
several seconds. If you quickly press the
Registration button, only the panel settings
(voice, etc.) that are not related to Rhythm
and Automatic Accompaniment will be
updated.
Transpose setting will be recalled the instant
you press a Registration button along with all
other panel settings.
INSTANT
DELAYED
To return to the basic screen, press the [Utility] button.
This setting remains stored in memory even while power is
turned off.
Settings related to Rhythm performances and
Automatic Accompaniment will be recalled
the instant you press a Registration button
along with all other panel settings.
INSTANT
To return to the basic screen, press the [Utility] button.
This setting remains stored in memory even while power is
turned off.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Composer Settings
Changing the Key When Playing Back
Songs (Playback Transpose)
SMF Music files or a performance that you recorded can be
transposed for playback.
Switching the Display of Lyrics On or
Off (Lyric)
1. Press the [Utility] button.
Some music files have Lyrics included and these Lyrics can be
displayed on the screen. You can turn on or off the lyrics
display of such music files.
2. Using the Menu [
] or [
] button, select
“Playback Transpose.”
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“Lyric.”
fig.09-11
3. Press the Value [-] or [+] button to select the
value for transpose.
Each press of the Value [-] and [+] buttons transpose the
key by a semitone.
You can transpose the song within a range of -6 to +5
semitone.
3. Press the Value [-] or [+] button to switch the
lyric display “ON (displayed)” or “OFF (not
displayed).”
To return to the basic screen, press the [Utility] button.
To return to the basic screen, press the [Utility] button.
You can transpose the keyboard for performance. For
details refer to “Transposing to a Different Key (Key
Transpose)” (p. 67).
If you press a voice select button while playing back music
files that contains lyrics, the display screen will switch, and
the lyrics will no longer be displayed. To re-display the
NOTE
lyrics, press the [Rec] button.
This setting remains stored in memory even while power is
turned off.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Metronome Setting
(Metronome)
Adjusting the Metronome Volume
(Metronome Volume)
This setting determines whether or not the metronome will
You can adjust the volume of the metronome.
sound.
1. Press the [Utility] button.
1. Press the [Utility] button.
2. Using the Menu [
] or [
] button, select
2. Using the Menu [
] or [
] button, select
“Metronome.”
“Metronome.”
3. Press the [Rec] button.
3. Press the [Rec] button.
4. Using the Menu [
] or [
] button, select
4. Using the Menu [
] or [
] button, select
“Metronome Volume.”
fig.09-03
“Metronome.”
fig.09-02
5. Press the Value [-] or [+] button to select the
5. Press the Value [-] or [+] button to select OFF,
desired volume level (1–10).
REC, or ON.
Increasing the value will raise the volume of the
metronome.
Setting
OFF
Descriptions
To return to the basic screen, press the [Utility] button.
Not heard at all
REC
ON
Heard only while recording
Heard constantly
To return to the basic screen, press the [Utility] button.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Sound of the Metronome
(Metronome Sound)
Setting the Beat (Beat)
This setting determines the beat to be used when recording
performance songs.
You can choose one of 4 different sounds for the metronome.
1. Press the [Utility] button.
1. Press the [Utility] button.
2. Using the Menu [
] or [
] button, select
2. Using the Menu [
] or [
] button, select
“Beat.”
“Metronome.”
fig.09-05
3. Press the Value [-] or [+] button to set the beat.
3. Press the [Rec] button.
Setting
4. Press the Menu [
] or [
] button to select
2/2, 0/4, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 3/8, 6/8,
9/8, 12/8
“Metronome Sound.”
fig.09-04
To return to the basic screen, press the [Utility] button.
When recording your performance with playing Rhythm
performances or Automatic Accompaniment, the beat is set
automatically.
NOTE
NOTE
5. Press the Value [-] or [+] button to select the
You cannot change the beat of previously recorded songs.
type of sound for the metronome.
Setting
CLICK&BELL
Descriptions
Conventional metronome sound
Electronic metronome sound
Human voice (English)
ELECTRONIC
VOICE ENGLISH
VOICE JPANESE
Human voice (Japanese)
To return to the basic screen, press the [Utility] button.
This setting remains stored in memory even while power is
turned off.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Silencing a Specific Track (Track Mute)
You can temporarily silence sound of a specific track. This is
Assigning Commercial SMF Music Files to the
Tracks
referred to as “Track Mute.”
Track
Channel
1. Press the [Utility] button.
R (Rhythm)
10
5, 6, 7, 8, 9, 11, 12, 13, 14, 15,
16
2. Using the Menu [
] or [
] button, select
A (Accomp)
“Track Mute.”
B (Bass)
L (Lower)
U (Upper)
S (Solo)
2
3
4
1
3. Press the Value [-] or [+] button to select the
track that you wish to mute.
From the left, these are “R (rhythm), A (accompaniment),
B (bass), L (lower), U (upper), S (Solo) and C (control).”
During recording, the control track will store the
operations as follows.
What is a Track?
The ATELIER’s Composer features seven tracks. The
following types of performance are recorded to the
tracks.
Panel Operations (Voice selections, Tempo
changes, Rotary fast/slow etc.)
Newly recorded performance data will be added
without erasing the previously recorded data.
If you wish to record new performance data, erase all
the recorded data (p. 94).
Track
R (Rhythm)
A (Accomp)
Descriptions
Rhythm performances, Drums/SFX
Automatic Accompaniment (except Bass)
Expression Pedal Operations
Pedal Bass voice, Bass part of the
Automatic Accompaniment
The way in which expression operations are recorded
will depend on the setting of the “Exp. Source” item
“Recording” in the Utility menu.
B (Bass)
L (Lower)
U (Upper)
S (Solo)
Lower voice
Upper voice
Solo voice
Expression pedal operations will be
recorded.
If expression data has already been
recorded, the previously recorded
PEDAL
Panel operations, Expression Pedal
operations
C (Control)
data will be erased as the new data
is recorded.
4. Press the [Rec] button.
not be recorded.
If expression data has already been
recorded, the previously recorded
COMPOSER
data will remain without being
erased.
The character changes to “–”, indicating that the track is
muted.
For details refer to “Changing the Function of the
Expression Pedal (Exp. Source)” (p. 107).
5. Once again press the [Rec] button, and muting
will be canceled.
To return to the basic screen, press the [Utility] button.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Settings
Muting Individual Channels of
Performance Data (Channel Mute)
Adjust the Standard Pitch (Master Tune)
You can mute (silence) individual channels of performance
data of SMF music files (commercially available).
The basic pitch of an instrument is generally considered as the
pitch of the middle A note. The “Master Tune” parameter lets
you adjust this basic pitch to match the pitch of any other
instruments that are playing together with the ATELIER.
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
1. Press the [Utility] button.
“Channel Mute.”
2. Press the Menu [
] or [
] button to select
3. Press the Value [-] or [+] button to select the
channel that you wish to mute.
“Master Tune.”
From the left, these are “1 Ch. (channel 1), 2 Ch. ... 15
Ch., and 16 Ch.”
fig.09-09
3. Press the Value [-] or [+] button to adjust the
basic pitch.
4. Press the [Rec] button.
Settings
fig.09-10
415.3Hz – 466.2Hz (0.1 Hz units)
To return to the basic screen, press the [Utility] button.
By pressing the Value [+] and [-] buttons simultaneously, you
can restore the default setting (440.0 Hz).
The number will change to “–,” indicating that the
corresponding channel has been muted.
This setting remains stored in memory even while power is
turned off.
5. Once again press the [Rec] button, and muting
will be canceled.
To return to the basic screen, press the [Utility] button.
Channel mute will be defeated when you select different
performance data.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifying Transmission of PC
Numbers (Send PC Switch)
Setting PC Numbers (PC Number)
You can specify the Program Change number that will be
transmitted from MIDI Out when a Registration is selected.
Transmission of PC (Program Change) numbers can be
switched ON/OFF.
1. Press the [Utility] button.
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“MIDI.”
2. Press the Menu [
] or [
] button to select
“MIDI.”
3. Press the [Rec] button.
3. Press the [Rec] button.
4. Press the Menu [
] or [
] button to select
“PC Number.”
4. Press the Menu [
] or [
] button to select
fig.12-26
“Send PC Switch.”
fig.12-25
5. Press the Menu [
] or [
] button to select
“Bank MSB,” “Bank LSB,” “PC Num.”
5. Press the Value [-] or [+] button to switch the
Send PC Switch “ON” or “OFF.”
6. Press the Value [-] or [+] button to change the
setting.
Setting
ON
OFF
Descriptions
PC numbers are transmitted.
PC numbers are not transmitted.
Menu
Bank MSB (Bank Select MSB)
Bank LSB (Bank Select LSB)
PC Num (PC Number)
Setting
0–127
0–127
1–128
To return to the basic screen, press the [Utility] button.
This setting remains stored in memory even while power is
turned off.
To return to the basic screen, press the [Utility] button.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Ch
1
MODE 1
MODE 2
MIDI IN Mode (MIDI IN Mode)
GS
GS
GS
GS
GS
GS
GS
GS
GS
GS
Solo
This instrument contains two sound generators: one for SMF
data playback and one for keyboard performance.
Normally, data received at the MIDI In connector will control
only the sound generator for SMF data playback. However by
changing the MIDI IN Mode setting, you can also control the
keyboard sound generator from MIDI In.
2
Pedal/GS *
Lower
3
4
Upper
GS
5–10
11
12
13
14–15
16
Drums/SFX
GS
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
Nothing
GS
“MIDI.”
Control
* When the pedal part button is ON, data received at the MIDI In
connector will control the pedal part of keyboard sound
generator.
When the pedal part button is OFF, data received at the MIDI In
connector will control the GS sound generator.
3. Press the [Rec] button.
There are limitations on the types of MIDI messages that can
be received by the keyboard sound generator.
4. Press the Menu [
] or [
] button to select
“MIDI IN Mode.”
This setting remains stored in memory even while power is
turned off.
To return to the basic screen, press the [Utility] button.
5. Press the Value [-] or [+] button to change the
setting for MIDI IN Mode.
Setting
Descriptions
Control the instrument as a GS sound
generator.
MODE 1
Channels 5 through 10 and Channels 12, 14,
15 are transmitted to the GS sound generator,
and all other channels are transmitted to the
keyboard sound generator.
MODE 2
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the V-LINK function (V-LINK)
Selecting the MIDI Transmit Channel
(Tx MIDI Channel)
When you use the MIDI connectors of the ATELIER to transmit
musical data to external devices, for each keyboard (Upper,
Lower, and Pedal) you can specify the channel on which your
playing will be transmitted as MIDI messages. You can modify
these Tx (Transmit) MIDI settings as needed.
Connecting the ATELIER to a V-LINK compatible image device
allows you to control the images with the ATELIER.
What is the V-LINK?
V-LINK (
) is a function that allows music and
images to be performed together. By using MIDI to connect
two or more V-LINK compatible devices, you can easily enjoy
a wide range of visual effects that are linked to the expressive
elements of a music performance.
For details refer to “Connecting MIDI Devices” (p. 123).
1. Press the [Utility] button.
How to Use the V-LINK
2. Press the Menu [
] or [
] button to select
“MIDI.”
1. Press the [Utility] button.
2. Press the Menu [
] or [
] button to select
“V-LINK.”
fig.10-14.eps
3. Press the [Rec] button.
4. Press the Menu [
] or [
] button to select
“TxMIDI Channel.”
3. Press the Value [-] or [+] button to select the
setting.
Setting
OFF
Descriptions
The V-LINK function is switched off.
The V-LINK function is switched on.
You can now control the video images using
the Registration buttons.
MODE 1
MODE 2
5. Press the Menu [
] or [
] button to select a
The V-LINK function is switched on.
You can now control the video images using
the twelve rightmost keys of the lower keyboard
and Registration buttons.
part.
Part
No sound is produced when you press any of
the twelve keys at the right end of the
keyboard.
Solo, Upper, Lower, Pedal, Control
6. Press the Value [-] or [+] button to select the
To return to the basic screen, press the [Utility] button.
MIDI transmission channel.
Channel
1–16
To return to the basic screen, press the [Utility] button.
The Control part transmits expression pedal data and PC
numbers.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
The V-LINK function is turned on, and the V-LINK icon
appears in the main screen.
You can also use the following procedure to turn the
V-LINK function on.
fig.09-41.eps
1,2
The Send PC Switch settings is automatically switched to
ON when V-LINK is on (MODE 1, MODE 2). When the V-
LINK function is switched off, the Send PC Switch setting
reverts to the setting in effect before V-LINK was switched
on.
1. Hold down the [Reset] button and press
either the Upper [Full] button or the Upper
[Brass] button.
When V-LINK is set to “MODE 1”
When a Registration button is pressed, “Bank Select”
and “Program Change Number” messages are
transmitted from the MIDI Out connector as video
control messages. At this time, the Control MIDI
transmit channel setting is disregarded, and the
messages are transmitted via Channel 16.
Holding down the [Reset] button and pressing the
Upper [Full] button switches the instrument to
“MODE 1” (p. 117). Holding down the [Reset]
button and pressing the Upper [Brass] button
switches the instrument to “MODE 2” (p. 117).
The display changes as shown below, and the
When V-LINK is set to “MODE 2”
In addition to the functions of “MODE 1,” MODE 2
also sets the device to transmit “Note messages” as
video control messages from the MIDI Out connector
when one of the twelve rightmost keys in the Lower
keyboard is pressed.
ATELIER switches to Image Control mode.
fig.09-42.eps
In this case, the Lower and Solo MIDI transmit channel
settings are disregarded, and the messages are
transmitted via Channel 16.
The V-LINK function is turned on, and the V-LINK
icon appears in the main screen.
The MIDI transmit channel used for video control
fig.09-41.eps
NOTE
messages is fixed at channel 16.
For more on switching video images, refer to the owner’s
manual for the connected device.
hold down the [Reset] button and press
either the Upper [Full] button or the Upper
[Brass] button.
If set to “MODE 1” (p. 117), holding down the
[Reset] button and pressing the Upper [Full] button
switches the V-LINK function off. If set to “MODE
2” (p. 117), holding down the [Reset] button and
pressing the Upper [Brass] button switches the V-
LINK function off.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Restoring the User Memory to
the Original Factory Settings
(User Memory Reset)
Restoring All Settings Other
Than the User Memory to the
Original Factory Settings
(Panel Reset)
You can restore the User memory to their original factory
settings.
This function is called “User Memory Reset.”
All settings other than the User memory can be returned to
their factory settings. This function is called “Panel Reset.”
1. Turn down the volume to the minimum level,
What is User Memory?
“User Memory” refers to an area inside the instrument
where you can store the registration you create and the
performances you record. Registration and SMF music files
saved on USB memory can also be copied to user memory.
User memory is quite useful, since anything you place
there will be retained even while the power is turned off.
The following things are stored in User memory:
then turn off the power.
2. While holding down the [Harmony
Intelligence] button, press the [Power On]
switch to turn the power on.
fig.01-15
• Songs you’ve registered in “Favorites”
• Rhythms
Do not turn off the power while the following screen is
displayed.
NOTE
• Registration sets
fig.01-16
1. Turn down the volume to the minimum level,
then turn off the power.
2. While holding down the Rhythm [Ballad/User]
button, press the [Power On] switch to turn the
power on.
When panel reset is completed, the basic screen is
appeared.
fig.01-15
Do not turn off the power while the following screen is
displayed.
NOTE
fig.01-16
The user memory will be reset to the factory-set state.
To reset all settings other than the User memory to their
original factory settings, refer to ”Panel Reset” (p. 119). If
you want to reset all settings to their factory-set state, refer to
“Factory Reset“ (p. 19).
When user memory reset is completed, the basic screen
is appeared.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Press the [Rec] button to start formatting.
Formatting a USB Memory
(Format)
The process of preparing USB memory or floppy disks so that
they can be used with the ATELIER is called “initialization”
(formatting).
In certain cases, particularly with floppy disks, the media is
formatted for a specific type of device. If the media format
does not match the ATELIER’s, you will not be able to use that
media with the ATELIER.
To return to the basic screen, press the [Utility] button.
Never attempt to remove the USB memory until formatting is
NOTE
complete.
1. Connect the USB memory to the external
memory connector
If you want to initialize a floppy disk, connect your
floppy disk drive (sold separately) to the external
memory connector, and insert the floppy disk.
2. Press the [Utility] button.
3. Press the Menu [
] and [
select “Media Utility.”
] buttons to
4. Press the [Rec] button.
5. Press the Menu [
] and [
select “Format Media.”
] buttons to
fig.02-10.eps
6. Press the [Rec] button.
The Format screen appears.
To cancel the procedure, press the [Reset] button.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with External Devices
If you want to hook up an external instrument to the ATELIER,
then this chapter is for you.
Connecting Audio Equipment
Names and Functions of Jacks
and Connectors
Output Jack
You can connect audio equipment using audio cables (sold
separately) and play the sounds from the ATELIER through the
speakers on the connected equipment or record your
performances on a recording device.
If the output of the connected device is monaural, you must use
the L (Mono) jack.
1
2
3
Use an audio cable to connect the input jack on the audio set
or amp mixer to one of the output jacks on the ATELIER. Use
an audio cable with a standard plug. When purchasing an
audio cable, please consult the vendor where you bought the
ATELIER.
Input Jack
You can connect another sound module, such as audio
equipment or an electronic instrument using audio cables (sold
separately) and play the sounds from the connected device
through the speakers on the ATELIER.
If the input of the connected device is monaural, you must use
the L (Mono) jack.
5
4
6
1. Output L/Mono, R Jacks
These jacks can be connected to your audio system to
enjoy more powerful sound.
2. Input L/Mono, R Jacks
Using these jacks, you can connect other sound
from other devices through the ATELIER’s speaker.
3. LCD Contrast Knob
Making the Connections
4. Phones Jacks → p. 18
To prevent malfunction and/or damage to speakers or other
Connect headphones here.
devices, always turn down the volume, and turn off the
power on all devices before making any connections.
NOTE
5. MIDI Out/In Connectors → p. 123
1. Turn down the volume all the way on all
You can connect external MIDI devices to the ATELIER
and exchange performance data between them.
equipment.
2. Turn off the power to the ATELIER and other
6. USB Connector → p. 122
connected equipment.
Used for connecting a computer to the ATELIER using a USB
cable.
3. Connect the ATELIER and other equipment with
audio cables (sold separately).
4. Turn on the connected equipment.
5. Turn on the ATELIER.
6. Adjust the volume.
After use, follow the steps below to switch off the power.
7. Turn down the volume all the way on all
equipment.
8. Turn off the ATELIER.
9. Turn off the connected equipment.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with External Devices
If connection to your computer is
unsuccessful...
Connecting a Computer
The following become possible once you connect a USB cable
(available separately) between the USB connector located to
the lower left of the ATELIER and the USB connector of your
computer.
Normally, you don’t need to install a driver in order to connect
the ATELIER to your computer. However, if some problem
occurs, or if the performance is poor, using the Roland
original driver may solve the problem. For details on
downloading and installing the Roland original driver, refer to
the Roland website.
• You can use the ATELIER to play sounds from SMF music
files played back with MIDI software.
Roland website: http://www.roland.com/
• By exchanging MIDI data with sequencer software, you
can save songs recorded with the ATELIER to your
computer, and enjoy a variety of musical control and
editing features.
Specify the USB driver you want to use, and then install the
driver.
Connect the ATELIER to your computer as shown below.
Caution
• To prevent malfunction and/or damage to speakers
or other devices, always turn down the volume, and
turn off the power on all devices before making any
connections.
• Only MIDI data can be transmitted using USB.
• USB cables are not included. Consult your Roland
dealer if you need to purchase.
• Turn on the power to the ATELIER before starting up
MIDI applications on the computer. Do not turn the
ATELIER on or off while any MIDI application is
running.
USB Cable
USB
Connector
Computer
* Refer to the Roland website for system requirements.
Roland website: http://www.roland.com/
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Making the Settings for the USB Driver
Connecting MIDI Devices
By connecting an external MIDI device and exchanging
performance data, you can control the performances on one
device from the other. For instance, you can output sound from
the other instrument or switch voice on the other instrument.
Normally, you don’t need to install a driver in order to connect
the ATELIER to your computer. However, if some problem
occurs, or if the performance is poor, using the Roland
original driver may solve the problem.
Specify the USB driver you want to use, and then install the
driver.
What’s MIDI?
1. Press the [Utility] button.
MIDI, short for “Musical Instrument Digital Interface,” was
developed as a standard for the exchange of performance
data between electronic instruments and computers.
The ATELIER is equipped with MIDI connectors to let it
exchange performance data with external devices. These
connectors can be used to connect the ATELIER to an external
device for even greater versatility.
2. Press the Menu [
] and [
] buttons to
select “USB Driver.”
fig.10-12.eps
About MIDI Connectors
3. Press the Value [-] and [+] buttons to select
The ATELIER has two kinds of MIDI connectors.
“GENERIC” or “ORIGINAL.”
Connecting these to the MIDI connectors on a MIDI instrument
makes it possible for the two instruments to control each other.
For instance, you can output sound from the other instrument
or switch tones on the other instrument.
Setting
Descriptions
Choose this if you want to use the
standard USB driver that was included
with your computer.
You should also set the MIDI send channel as needed (p. 117).
GENERIC
fig.10-09.eps
Normally, you should use this mode.
Choose this if you want to use a USB
driver downloaded from the Roland
website.
ORIGINAL
MIDI Out Connector
Connect the external MIDI device to the MIDI IN connector
with an optional MIDI cable. The notes played on the
keyboard, movements of the Damper pedal, Expression data,
data indicating that a Registration button [1]–[8], etc., was
pressed will be transmitted to the external MIDI connector.
4. Turn the ATELIER’s volume to the minimum
level, switch off the power, then turn it back on
again.
This setting remains stored in memory even while power is
turned off.
MIDI In Connector
with an optional MIDI cable. Performance messages from an
external MIDI device are received here.
instrument to play sounds or switch voices.
The ATELIER contains two sound generators: one sound
generator for its own keyboards and one GM2/GS sound
generator (p. 133). Normally, musical data transmitted from
an external device to the MIDI In connector is sent to the
GM2/GS sound generator, but you can also set the “MIDI IN
Mode” parameter (p. 116) so that the keyboard sound
generator is controlled.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with External Devices
Making the Connections
To prevent malfunction and/or damage to speakers or other
devices, always turn down the volume, and turn off the
power on all devices before making any connections.
NOTE
1. Turn the volume all the way down on the
ATELIER and on the device you’re about to
connect.
2. Switch off the power to the ATELIER and the
device you’re about to connect.
3. Use a MIDI cable (sold separately) to connect
the MIDI connectors to each other.
4. Switch on the power to the ATELIER and the
connected device.
5. Adjust the volume level on the ATELIER and the
connected device.
6. You should also set the MIDI send channel as
needed (p. 117).
Connection Example:
Connecting the MIDI Device
ATELIER
MIDI
Out
In
External MIDI Devices
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If the ATELIER does not function in the way you except, first check the following chart. If this does not
resolve the problem, consult your dealer or a nearby Roland Service Station.
Problem
Check
Solution
Page
p. 16
When you press the [Power On]
switch, the power doesn’t come on
Power cord is not connected correctly. Connect the power cord correctly.
The ATELIER uses a liquid-crystal
screen, so text may not be displayed
when the ambient temperature is
below freezing.
Nothing appears on screen
This is not a malfunction.
- - -
- - -
This is due to the nature of a liquid
crystal display, and is not a
malfunction.
It appears as though there are
vertical stripes in the screen
This is not a malfunction.
The device connected to the Input
jack is not loud enough
Could you be using a connection cable
that contains a resistor?
Use a connection cable that does not
contain a resistor.
- - -
The volume level of the instrument
connected to ATELIER is too low.
Could you be using a connection cable
that contains a resistor?
Use a connection cable that does not
contain a resistor.
p. 121
We cannot guarantee operation if
you’re using USB memory not made by
Roland.
Could you be using USB memory not
made by Roland?
Can’t read/write USB memory
- - -
If there is a cell phone nearby, you
may hear noise from the ATELIER when
an incoming call or outgoing call
occurs, or during a conversation.
Keep the cell phone as far away as
possible, or turn off its power.
Noise is heard in the sound
- - -
p. 18
p. 18
The [Master Volume] knob is set too
low.
Turn the [Master Volume] knob toward
“Max.”
Headphones are connected.
When you connect the headphones,
the sound is heard only through the
headphones.
If you want sound to be output from the
speakers, disconnect the headphones.
The plug is still plugged into the
headphone jack.
Disconnect the plug from the
headphone jack.
p. 18
p. 36
p. 71
No sound is heard
The volume is set too low on the Level
[▲] or [▼] button.
Press the Level [▲] or [▼] button to
raise the volume.
The volume is set too low on the
Expression Pedal.
Advance the expression pedal.
You do not have a Voice selected.
Voices that have their button indicator
lit can be played.
Press a voice button to select a voice.
p. 27
p. 38
Drums/SFX are selected for the Lower
keyboard, but you are playing a key to
which no drum sound is assigned.
No sound is heard
(by the Lower keyboard)
Turn the Drums/SFX off or play keys to
which drums sounds are assigned.
Use the correct procedure to turn on
the power of the connected external
devices.
p. 121
–
p. 124
No sound is heard (when external
devices are connected)
The power of the connected external
devices is not turned on.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Solution
Page
The V-LINK function is set Mode 2.
When V-LINK setting is Mode 2, the
group of twelve keys starting at the
very right of the lower keyboard are
used for controlling video images.
Therefore, no sounds are played even
when you press these keys.
There is no sound from the twelve
keys at the right of the lower
keyboard
Turn the V-LINK function off, or select
Mode 1 for the V-LINK function.
p. 117
The damper pedal affects only the
Lower keyboard. The damper pedal
does not affect the Upper Keyboards
and Bass pedalboard.
This is not a malfunction.
This is not a malfunction.
p. 68
- - -
Damper Pedal does not operate
The damper pedal does not affect the
Solo voice.
The function of the Expression Pedal
during recording or the function during
playback has been set to
Set the expression pedal function
during recording to “PEDAL,” and
during playback to “PEDAL” or
“PEDAL+COMPOSER.”
Expression Pedal does not
operate
p. 107
“COMPOSER.”
If “Registration Shift” (change
Registrations) is “RIGHT,” “LEFT,” or
“RIGHT + Load Next,” the foot switch
will be dedicated to switching the
Registration.
Can’t use the function assigned to
the foot switch
Turn “Registration Shift” off.
p. 70
When the human voice “Jazz Scat”
is selected, playing dynamics do
not change the sound
The setting of “Initial Touch” is turned
OFF.
Turn “Initial Touch” on.
This is not a malfunction.
p. 106
- - -
Some sounds do not allow the rotary
effect to be applied.
Rotary effect is not be applied
When you release your fingers
from keys in the Lower keyboard,
the notes continue sounding
Press the Pedal [To Lower] button to
turn it off (dark).
The Lower Voice Hold is at ON.
p. 38
Even though you press only one
key, a multiple number of notes
sound
Harmony Intelligence is at ON.
Chord Intelligence is turned ON.
Turn “Harmony Intelligence” off.
Turn “Chord Intelligence” off.
p. 72
p. 48
When Chord Intelligence is OFF, the
keys for a chord were not pressed
simultaneously.
Either turn on the Chord Intelligence
function, or play the chord correctly.
p. 48
p. 48
When Chord Intelligence is OFF, the
chord is not being pressed correctly.
Either turn on the Chord Intelligence
function, or play the chord correctly.
Automatic Accompaniment
sounds odd
When performance data from a device
other than the ATELIER is being played
together with the Automatic
This is not a malfunction.
This is not a malfunction.
- - -
Accompaniment, the Automatic
Accompaniment may not be sounded
correctly.
When performance data from a device
other than the ATELIER is being played
together with the Automatic
Accompaniment, the Rhythm
performance may not be sounded
correctly.
Rhythm sounds odd
- - -
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Transpose is in effect.
The tuning is incorrect.
Solution
Page
Simultaneously press the Transpose [-]
and [+] buttons to cancel the
transposition (the Transpose [-] and [+]
buttons’ indicators will go out).
p. 67
p. 114
p. 37
Pitch is off
Adjust the standard pitch.
While set for an octave shift, you are
playing keys beyond the
recommended range. This does not
indicate a malfunction.
Adjust the Octave Shift setting.
While the Utility menu appears in the
display (with the exception of Channel
Mute and Track Mute), playback is not
allowed.
If you wish to playback performance
data, press the [Utility] button once
again to exit the Utility menu
Performance data cannot be
played back
- - -
If you wish to erase a previously-
recorded track and then re-record,
press the track button for the desired
track to make that button blink before
you begin recording.
Press the track button for the desired
track to make that button indicator
blink before you begin recording.
p. 94
Recording is not possible
If you wish to record performance
data, press the [Utility] button once
again to exit the Utility menu.
While the Utility menu appears in the
display, recording is not allowed.
- - -
p. 96
- - -
A performance cannot be restored
once it’s been deleted, so be sure to
save it on a floppy disk before you turn
off the power.
Any performance that has been
recorded is deleted when the power to
the ATELIER is turned off.
The recorded performance has
disappeared
When a voice is selected for the Pedal
Bass part, the bass of the Automatic
Accompaniment will not sound.
The bass note of the Automatic
Accompaniment does not sound
This is not a malfunction.
This is not a malfunction.
When you started a Rhythm with
an Intro, the
Rhythm did not sound.
Some Rhythms do not have rhythm
sounds in the intro.
- - -
The Part Balance volume of each part
is too high.
Press the Part Balance button to lower
the volume.
p. 36
The Reverb volume has been raised
when the volume of each Part Balance
button is already raised.
p. 36
p. 77
Either lower the Reverb volume, or
adjust the Part Balance of each part.
Sound is distorted / cracked
The [Master Volume] slider has been
used to raise the overall volume
excessively.
Use the [Master Volume] slider to lower
the overall volume.
p. 18
- - -
Some keys (of certain keyboard
parts) sound strange
You are playing notes outside the
recommended range of the voice.
This is not a malfunction.
The Rhythm does not change
when you press the Registration
buttons
The settings at which Registrations are
recalled (Registration Arranger
Update) has been set to “DELAYED.”
Set the timing at which the arranger
settings are called up (Registration
Arranger Update) to “INSTANT.”
p. 57
p. 109
The Pedal [To Lower] button or the
”Bass Split” function is on.
When the Pedal [To Lower] button is
on, the Bass will be sounded by the
Lower keyboard.
In the Pedal part, press the Pedal [To
Lower] button or ”Bass Split” function is
off.
Bass is heard even though you are
not playing the Bass Pedalboard
p. 86
p. 88
When playing the same sound in
the Upper keyboard and Lower
keyboard, the volume is different
Set the initial touch settings of the
Upper keyboard and the Lower
keyboard to both On, or both Off.
On one of the keyboards, “Initial
Touch” is turned ON.
p. 106
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Check
Solution
Page
- - -
The Lower keyboard will not produce
Lower keyboard cannot be heard sound while an Intro or Ending is being
This is not a malfunction.
played.
If you layer the same type of sound (for
example, Strings 1 and Strings 5), or
play an octave-shifted organ sound,
You are layering sounds of the same
type (e.g., Strings 1 and Strings 5).
Alternatively, you are playing an
organ sound with Octave Shift.
This is not a malfunction.
the timing at which you play a note or
The sound is not played correctly
- - -
the phase relationship between the two
sounds may affect the way in which the
sounds are heard, but this is not a
malfunction.
Percussion [2 2/3’] button is turned
on.
If Percussion [2 2/3’] button is on, the
sound of the 1’ harmonic bar will not
be heard
Can’t hear the 1’ harmonic bar
This is not a malfunction.
This is not a malfunction.
- - -
- - -
With some music files, the lyrics cannot
be displayed correctly.
A button was pressed while the lyrics
were being shown in the display.
During the display of lyrics, you could
be taken to a different screen if you
press a button.
Lyrics are not indicated properly
in the display
If you want to have the lyrics be
displayed again, Press the [Rec] button
p. 92
Certain instrument is not heard
while playing a song
p. 91
p. 113
The track is muted.
Turn off track muting.
Can’t use Chord Intelligence
function
Chord Intelligence is at OFF.
Turn “Chord Intelligence” on.
p. 48
When listening through speakers:
Playing at loud volumes may cause
instruments near the ATELIER to
resonate. Resonance can also occur
with fluorescent light tubes, glass
doors, and other objects. In particular,
this problem occurs more easily when
the bass component is increased, and
when the sound is played at higher
volumes.
Use the following measures to suppress
such resonance.
• Place speakers so they are 10-15 cm
from walls and other surfaces.
• Reduce the volume.
• Move the speakers away from any
resonating objects.
- - -
The Bass Range Sounds Odd, or
There Is a Vibrating Resonance
When listening through headphones:
Here, a different cause (such as
resonance produced by the ATELIER)
would be suspect.
Consult your Roland dealer or nearest
Roland Service Center.
- - -
The expression pedal function is set to
“PEDAL+COMPOSER” during
playback of ATELIER performance
data.
Pressing the expression pedal
while playing back ATELIER
performance data produces a
crackling noise
When this setting is used, moving the
expression pedal while playing back
ATELIER performance data may create
a difference between the expression
pedal information in the performance
data and the volume as set with the
expression pedal, which can result in
this kind of sound being produced.
Set the expression pedal function to
“PEDAL” during playback.
p. 107
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Message
Error Message
Copy Protected.
Meanings
To protect the copyright, this music file cannot be saved as SMF format.
Can’t Save.
Write-Protected
Media.
The protect tab of the storage media is set to the Protect (write prohibit) position.
Move the tab to the Write (write permit) position and try the operation again.
Can’t Save
This Song.
You can only play the music data. It cannot be saved on a storage media
This storage media does not allow initialization or saving. Insert a different storage media and try the
operation again.
Master Disk
Read Only File.
No Media
You cannot overwrite-save or delete a file on this storage media.
Storage media is not connected. Please connect storage media.
Saving is not possible because the storage media does not have enough space. Please use other storage
media that has been formatted by the ATELIER.
Media Full
Unknown Media
Media Ejected
Damaged Media
Can’t Read
This storage media cannot be used. Please format it.
The storage media was disconnected while it was being accessed. Please try the operation again.
A damaged area was found on the storage media.
This data cannot be read.
Playback was halted because the song could not be read fast enough.
The song could not be read from the storage media fast enough for playback. Press the [Reset] button, then
press the [Play/Stop] button once again.
Can’t Play
No Rhythm
There is no rhythm in user memory.
The rhythm used by the selected registration was deleted from user memory, or its order was changed.
The song data is excessively large, and cannot be loaded.
Memory Full
The performance data is excessively large, and cannot be loaded.
The data cannot be stored in user memory since user memory is full.
The ATELIER cannot deal with the excessive MIDI data sent from the external MIDI device. Reduce the
amount of MIDI data sent to the ATELIER.
MIDI Buffer Full
A MIDI cable or computer cable has been disconnected. Connect it properly and securely.
Communication
Error
The ATELIER is unable to handle the data that was sent. Please send data that the ATELIER is able to handle.
A MIDI
transmission error
has occurred.
Data transfer failed. Please transfer the data again.
Memory Full
Recording or editing is not possible because the memory of the ATELIER is full.
An error occurred in internal memory. Please perform the operation again. If this indication appears even
after you’ve repeated the operation several times, please contact Roland service.
Memory Error
This is registration
data of a type that
is not supported.
This instrument cannot use this registration.
USB memory not supported by the ATELIER was connected. This USB memory cannot be used with the
ATELIER.
USB over current
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Chord List
● symbol: Indicates the constituent not of chord.
★ symbol: Chord shown with an “★”can be played by pressing just the key marked with the “★.”
Chord 1.eps
C
C#
D
E
E
E
E
E
E
E
F
Cmaj7
C7
C#maj7
C#7
Dmaj7
D7
maj7
7
Emaj7
E7
Fmaj7
F7
Cm
C#m
Dm
m
Em
Fm
Cm7
Cdim
C#m7
C#dim
Dm7
Ddim
m7
dim
Em7
Edim
Fm7
Fdim
Cm7
5
C#m7
5
Dm7
5
E
E
E
E
E
E
m7
5
Em7
5
Fm7
5
Caug
Csus4
C#aug
C#sus4
Daug
Dsus4
aug
sus4
Eaug
Esus4
Faug
Fsus4
C7sus4
C6
C#7sus4
C#6
D7sus4
D6
7sus4
E7sus4
E6
F7sus4
F6
6
Cm6
C#m6
Dm6
m6
Em6
Fm6
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Chord List
● symbol: Indicates the constituent not of chord.
★ symbol: Chord shown with an “★”can be played by pressing just the key marked with the “★.”
Chord 2.eps
F#
G
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
F#maj7
F#7
Gmaj7
G7
maj7
7
Amaj7
A7
maj7
7
Bmaj7
B7
F#m
Gm
m
Am
m
Bm
F#m7
F#dim
F#m7
F#aug
F#sus4
Gm7
Gdim
Gm7
Gaug
Gsus4
m7
dim
m7
aug
sus4
Am7
Adim
Am7
Aaug
Asus4
m7
dim
m7
aug
sus4
Bm7
Bdim
Bm7
Baug
Bsus4
5
5
5
5
5
5
F#7sus4
F#6
G7sus4
G6
A
A
7sus4
6
A7sus4
A6
B
B
7sus4
6
B7sus4
B6
F#m6
Gm6
A
m6
Am6
B
m6
Bm6
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Arrangement
Registration
This refers to changes that have been made in an original
tune, by adding a new accompaniment or by changing the
instruments used.
A set of data that specifies the state of the instrument when
performing, including sounds and panel settings.
Reverb
Automatic Accompaniment
An effect that simulates the reverberation of a room or concert
hall.
Automatic Accompaniment is automatic accompaniment when
just a few keys in the lower section of the keyboard are
pressed to specify the chord.
Root Note
The root note is the basis of a chord. All chords are built on a
root note, which is the part of the chord name given in
uppercase letters.
Basic Chord
This refers to the most commonly used types of chord, which
are generally the following six types: major chords, minor
chords, minor seventh chords, minor seventh (5) chords,
dominant seventh chords, and diminished seventh chords.
Rotary
An effect which simulates the modulation given to the sound
when a rotating speaker is used. The Rotary effect produces
two types of modulation: fast or slow.
Chord
Notes of two or more pitches sounded simultaneously. Chords
consisting of three notes are called “triads,” and are the most
basic type of chord.
Sound Generator
This is the section that produces the sound. The ATELIER series
uses a sound generator that is compatible with GM2/GS.
Ending
This is the last part of the accompaniment. When you stop
playing the Automatic Accompaniment, the ATELIER plays an
Ending appropriate for the Rhythm.
Split
A function which allows the keyboard to be divided into two
or more areas, and a different sound assigned to each area.
The point at which the keyboard is divided is called the “Split
Point.”
Glide
An effect that temporarily lowers the pitch and then gradually
returns it to normal.
Sustain
Intro
An effect that adds a decay to each note. The ATELIER allows
sustain to be applied to the voices of the upper part, lower
part, and pedal part.
This is the introductory portion of an Automatic
Accompaniment performance. When automatic
accompaniment begins, the ATELIER can add an appropriate
intro for each rhythm.
Voice
The ATELIER is able to produce the sounds of various
instruments. These sounds are called “Voices.”
Inversion
When the lowest note of a chord is the root, the chord is said
to be in “root position.” In contrast, forms of a chord in which
other notes are the lowest pitch are called “inversions.”
Mute
To silence a sound. The ATELIER provides a Track Mute
function that allows you to turn off the track button indicator of
a track on which music data has been recorded, so that the
corresponding track will temporarily be silenced.
Panel Settings
Settings such as sound selections, tempo, Rotary fast/slow.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Music Files That the ATELIER Can Use
What Are Music Files?
■ About the ATELIER Sound Generator
Music files contains musical information such as how long the key for
a corresponding pitch is played, the force applied to the key played,
and other such information. Performance data is transmitted to the
ATELIER from music files saved in USB memory and CD-ROM, and
played back without change as songs. This is different than an audio
CD, since the music file does not contain a recording of the sound
itself. This makes it possible to change tempos and keys freely,
allowing you to use it in many different ways.
The ATELIER come equipped with GM 2/GS sound generators.
General MIDI
The General MIDI is a set of recommendations which seeks to provide
a way to go beyond the limitations of proprietary designs, and
standardize the MIDI capabilities of sound generating devices. Sound
generating devices and music files that meets the General MIDI
standard bears the General MIDI logo. Music files bearing the
General MIDI logo can be played back using any General MIDI
sound generating unit to produce essentially the same musical
performance.
Regarding Copyright
Use of the internal songs and audio files for any purpose other than
private, personal enjoyment without the permission of the copyright
holder is prohibited by law. Additionally, this data must not be
copied, nor used in a secondary copyrighted work without the
permission of the copyright holder.
General MIDI 2
The upwardly compatible General MIDI 2 recommendations pick up
where the original General MIDI left off, offering enhanced expressive
capabilities, and even greater compatibility. Issues that were not
covered by the original General MIDI recommendations, such as how
sounds are to be edited, and how effects should be handled, have
now been precisely defined. Moreover, the available sounds have
been expanded. General MIDI 2 compliant sound generators are
capable of reliably playing back music files that carry either the
General MIDI or General MIDI 2 logo.
Please be aware that if you create derivative works that are based on
existing copyrighted material, such as commercially available SMF
music files, such works may violate copyright law if used for any
purpose other than personal enjoyment. Roland takes no responsibility
for any copyright violation you may commit by creating such works.
■ The ATELIER Allows You To Use the
Following Music Files
In some cases, the conventional form of General MIDI, which does not
include the new enhancements, is referred to as “General MIDI 1” as
a way of distinguishing it from General MIDI 2.
VIMA TUNES
VIMA TUNES is a Roland specification for music files that contains
image and lyric data, allowing you to enjoy songs with lyrics and
images simultaneously. When data bearing the “VIMA TUNES” logo
is played back on a device that bears the same logo, lyrics can be
shown on the screen of a connected external display or television,
letting you enjoy karaoke or watch a slide show.
GS Format
The GS Format is Roland’s set of specifications for standardizing the
performance of sound generating devices. In addition to including
support for everything defined by the General MIDI, the highly
compatible GS Format additionally offers an expanded number of
sounds, provides for the editing of sounds, and spells out many details
for a wide range of extra features, including effects such as reverb
and chorus. Designed with the future in mind, the GS Format can
readily include new sounds and support new hardware features when
they arrive. Since it is upwardly compatible with the General MIDI,
Roland’s GS Format is capable of reliably playing back GM Scores
equally as well as it performs GS music files (music files that have
been created with the GS Format in mind). This product supports both
the General MIDI 2 and the GS Format, and can be used to play back
music data carrying either of these logos.
SMF Music Files
SMFs (Standard MIDI Files) use a standard format for music file that
was formulated so that files containing music file could be widely
compatible, regardless of the manufacturer of the listening device. An
enormous variety of music is available, whether it be for listening, for
practicing musical instruments, for Karaoke, etc.
SMF with Lyrics
“SMF with Lyrics” refers to SMF (Standard MIDI File) that contains the
lyrics. When Music Files carrying the “SMF with Lyrics” logo are
played back on a compatible device (one bearing the same logo), the
lyrics will appear in its display.
XGlite
XG is a tone generator format of YAMAHA Corporation, that defines
the ways in which voices are expanded or edited and the structure
and type of effects, in addition to the General MIDI specification.
XGlite is a simplified version of XG tone generation format. You can
play back any XG music files using an XGlite tone generator.
However, keep in mind that some music files may play back differently
compared to the original files, due to the reduced set of control
parameters and effects.
The ATELIER come equipped with GM 2/GS sound generators.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings That Are Stored After the Power Is Turned Off
Bank LSB (Bank Select LSB)
Bank MSB (Bank Select MSB)
Wall Type
The Voices assigned for each part
Level [ ▲ ][ ▼ ] (Part Balance Volume)
The Reverb depth for each part
The Octave settings for each part
The voices assigned to the [Others] buttons for each part
[Drums/SFX] button (ON/OFF)
Settings That Are Stored After the
Power Is Turned Off
Arranger Update
Auto Std Tempo (Auto Standard Tempo)
Lyrics
Master Tune
Metronome Sound
MIDI IN Mode
Drum/SFX Set
Registration Shift
Selected Rhythm
Send PC Switch
Trans. Update (Transpose Update)
USB Driver
Registration Name
[Intro/Ending] button (ON/OFF)
Synchro Start (ON/OFF)
Variation
Chord Intelligence ON/OFF
Leading Bass ON/OFF
Arranger [ON/OFF] button (ON/OFF)
Lower Voice Hold (ON/OFF)
Tempo setting
Settings That Are Stored In the
Registration Buttons
Registration Name
Volume of the rhythm part
Registration Shift
Arranger Update
Trans. Update (Transpose Update)
Reverb depth of the rhythm Accompaniment part
Reverb depth of the rhythm drum part
Reverb depth of the rhythm bass part
Settings That Are Stored In the
Individual Registration Buttons
Reverb Type
Reverb Depth
Solo [To Lower] button (ON/OFF)
Pedal [To Lower] button (ON/OFF)
Transpose [-] [+] button (Key Transpose)
L Foot Switch Assignment (Left Foot Switch Assignment)
R Foot Switch Assignment (Right Foot Switch Assignment)
[Harmony Intelligence] buttons (ON/OFF)
Harmony Intelligence Type
Rotary [Fast/Slow] button (ON/OFF)
Rotary [On/Off] button (ON/OFF)
Pedal Bass Mode
Solo Mode
Solo To Lower Mode
Solo Split Point
Bass Split (ON/OFF)
Bass Split Point
Sustain ON/OFF
Sustain Length
Tx MIDI Channel
Initial Touch (Initial Touch Sensitivity)
Vintage Organ Type
Vintage Organ Volume
PC Number (Program Change Number)
134
Download from Www.Somanuals.com. All Manuals Search And Download.
MIDI Implementation Chart
Roland Organ
Date : May 1, 2008
Version : 1.00
Model AT-100/AT-300
MIDI Implementation Chart
Transmitted
Recognized
Remarks
Function...
*5
*5
*5
*5
*5
*5
*6
1 (Solo)
2 (Pedal)
3 (Lower)
4 (Upper)
11 (Drums/SFX)
16 (Expression, PC)
1 (Solo)
2 (Pedal)
3 (Lower)
Default
Basic
Channel
4 (Upper)
11 (Drums/SFX)
16 (Expression)
1–16 (GM2/GS)
X
1–16
Changed
Default
Messages
Altered
x
x
Mode 3
Mode 3, 4(M=1)
*10
Mode
**************
Note
Number :
32–103
**************
0–127
0–127
True Voice
Note ON
Note OFF
O
x
*1
*1
O
x
Velocity
8n v=64
After
Touch
Key's
Ch's
x
x
O
O
*2, 8
*2, 7, 8, 9
Pitch Bend
x
O
*2, 7, 8, 9
0, 32
1
5
6, 38
7
10
11
16
64
65
66
67
71
72
73
74
75
O
x
x
x
x
x
O
x
O
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
*3, 7, 8
*2, 7, 8, 9
*2, 7, 8
*2, 7, 8, 9
*2, 7, 8, 9
*3, 7, 8, 9
*3, 7, 8, 9
*4
Bank select
Modulation
Portamento time
Data entry
Volume
Panpot
Expression
General purpose controller (Glide)
Control
Change
*3, 7, 8, 9
*3, 7, 8
*2, 7, 8
*2, 7, 8
*7
*7
*7
*7
*7
*7
*7
Hold 1
Portamento
Sostenuto
Soft
Resonance
Release Time
Attack Time
Cut off
Decay Time
Vibrato Time
Vibrato Depth
Portamento control
Effect1 depth
Effect3 depth
NRPN LSB, MSB
RPN LSB, MSB
76
77
84
91
*2, 8
*3, 7, 8
*3, 7, 8
*3, 8
93
98, 99
100, 101
*2, 7, 8, 9
Prog
0–127
*1
O
*3, 7, 8, 9
Change
**************
0–127
Program number 1–128
: True #
*11
System Exclusive
O
O
: Song Pos
: Song Sel
: Tune
x
x
x
x
x
x
System
Common
System
Real Time
: Clock
: Commands
O
O
x
x
x
x
x
x
O
x
O (120, 126, 127) *7, 8
: All sound off
O
*7, 8
:
Reset all controllers
Aux
Message
x
: Local Control
: All Notes OFF
: Active Sense
: Reset
*7, 8, 9
O (123–125)
O
x
* 1 O x is selectable.
* 6 With MIDI IN Mode 1
* 7 Received in GM2 mode
* 8 Received in GS mode
* 9 Received in General MIDI mode
*10 Recognized as M=1 even if M≠1.
*11 V-LINK
Notes
* 2 O x is selectable by SysEx. (GS Part)
* 3 Not received in the keyboard part
* 4 Can be received in the keyboard part
* 5 With MIDI IN Mode 2
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
O : Yes
X : No
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
AT-300, AT-100: MUSIC ATELIER
AT-300
49 keys (C3 – C7)
AT-100
Upper
Lower
61 keys (Waterfall keyboard, C2 – C7)
20 keys (C2 – G3)
Keyboard
Pedal
Initial Touch
Sound Generator
Max. Polyphony
Upper, Lower (10 levels for each)
Conforms to GENERAL MIDI 2, GENERAL MIDI System, GS and XGlite format
128
Sound
Generator
180 Voices (Included 8 Active Expression
Voices)
120 Voices (Included 5 Active Expression
Voices)
Voice
Part
Upper, Lower, Solo, Pedal
Flute (with harmonic bars)
120 rhythms in 8 groups x 4 variations
99 rhythms
Vintage Organ
Rhythm
80 rhythms in 8 groups x 4 variations
Rhythm
User Rhythm
Tempo, Arranger On/Off, Start/Stop, Synchro Start, Intro/Ending, Intro Count Down,
Break, Auto Fill In, Variation (4 variations), One Touch Program, Chord Intelligence,
Leading Bass, Auto Standard Tempo
Arranger Function
120 rhythms x 4 variations
12 Drum Sets + 1 SFX Set
12 types
80 rhythms x 4 variations
8 Drum Sets + 1 SFX Set
9 types
One Touch Program
Drums/SFX Sets
Harmony Intelligence
Master Tuning
415.3 Hz–466.2 Hz (0.1 Hz steps)
-4–+7 (in semitones)
-6–+5 (in semitones)
Rotary Sound, RSS Reverb, Sustain, Glide
8
Key Transpose
Playback Transpose
Effects
Registration
Registration
Function
Load Next, File Edit
7 tracks (playback)
Tracks
Note Storage
Song Length
Tempo
Approx. 40,000 notes
Max. 999 measures
Quarter note = 20–500
120 ticks per quarter note
Realtime (Replace)
Composer
Resolution
Recording
Alphabet
Lyrics Display
File Storage
Media
USB memory (option), floppy disk (in the case of using optional USB floppy disk drive)
MUSIC ATELIER original format, SMF format 0
Save Format
Songs
Max. 99 songs for each folder
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
AT-300
AT-100
30 W + 30 W
20 W + 20 W
Full-range 16 cm x 2
Rated Power Output
Speaker
Full-range 20 cm x 2 (with speaker box)
128 x 64 dots backlit LCD
Display
Damper Pedal, Expression Pedal, Foot Switch: 2 pcs. (function assignable)
Pedals, Switches
Audio Output Jacks (L/mono, R), Audio Input Jacks (L/mono, R),
Phones Jacks (stereo) x 2, MIDI connectors (In, Out), USB (MIDI) Jack,
External Memory connector (USB Memory connector), AC Inlet
Connectors
AC 117 V, 230 V, 240 V
Power Supply
Power Consumption
Finish
80 W
70 W
Simulated Dark Walnut
1,233(W) x 551(D) x 466 (H) mm
Console
1,210(W) x 534(D) x 390 (H) mm
(included Music
Rest)
48-9/16 (W) x 21-3/4 (D) x 18-3/8 (H)
inches
47-11/16 (W) x 21-1/16 (D) x 15-3/8 (H)
inches
1,229 (W) x 515 (D) x 748 (H) mm
1,229 (W) x 515 (D) x 748 (H) mm
Stand
Total
Dimensions
48-7/16 (W) x 20-5/16 (D) x 29-1/2 (H)
inches
48-7/16 (W) x 20-5/16 (D) x 29-1/2 (H)
inches
1,233 (W) x 553 (D) x 1,172 (H) mm
48-9/16 (W) x 21-13/16 (D) x 46-3/16
(H) inches
1,229 (W) x 542 (D) x 1,096 (H) mm
48-7/16 (W) x 21-3/8 (D) x 43-3/16 (H)
inches
Console
Stand
Total
43.5 kg / 96 lbs
37 kg / 82 lbs
31.5 kg / 70 lbs
22.5 kg / 50 lbs
54 kg / 120 lbs
Weight
80.5 kg / 178 lbs
Music Rest, Power Cord, Knob Bolt x 2, Cord Hook, Owner’s Manual,
Voice & Rhythm Guide
Accessories
Options
Bench, Stereo Headphones, USB Memory (M-UF1G), USB Floppy Disk Drive (FD-01A), CD
Drive Holder (DH-01)
962a
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Demo Song List
Song Title
Composer
Player
Akio Sasaki
Ralf Schink
Ric Iannone
Ric Iannone
Ric Iannone
Ric Iannone
Ric Iannone
Ric Iannone
Copyright
Jazz Organ
Pop Organ
Jazz Combo
Slow Waltz
Hawaiian
Akio Sasaki
Ralf Schink
Ric Iannone
Ric Iannone
Ric Iannone
Ric Iannone
Ric Iannone
Ric Iannone
© 2007 Roland Corporation
© 2004 Roland Corporation
© 2003 Roland Corporation
© 2003 Roland Corporation
© 2003 Roland Corporation
© 2003 Roland Corporation
© 2001 Roland Corporation
© 1999 Roland Corporation
Dixieland
Soft Gospel
Jazz Scat
981a
* All rights reserved. Unauthorized use of this material for purposes other than private, personal
enjoyment is a violation of applicable laws.
982
* No data for the music that is played will be output from MIDI Out connector.
Profile
Akio Sasaki
After graduating from the Berklee College of Music in Boston as a principle, Akio has been active as
a top jazz organ player in Japan. He performs live throughout the country, and also teaches at the
Senzoku Gakuen College of Music and at the Kyoto Musical Academy. Additionally, he has
published numerous arrangements, works of music theory, and music education books. In 2005 he
released his own trio’s CD album “Glide in Blue,” receiving high praise not only from organ fans but
also from many jazz fans. In 2007 he released his new album “Fly by Night,” and his musical career
continues to expand.
Ralf Schink
Ralf Schink was born in Germany and began playing the electronic organ at the age of 9. After
completing his formal education Ralf went on to study at the renowned Swiss Jazz School in Bern,
Switzerland as well as the Berklee College of Music in Boston. Since then, his energetic,
contemporary style has won him many accolades throughout Europe and around the world. Ralf
regularly performs at the Frankfurt Musik Messe, the largest musical fair in Europe. A tremendously
versatile and gifted musician, Ralf is comfortable with all types of music. From pop to jazz, Ralf’s
repertoire appeals to all age groups. Since 1992 Ralf has been working and touring for Roland
Europe as demonstrator and product consultant. He regularly tours Europe, Asia and Canada.
Ric Iannone
Ric Iannone began playing the piano and accordion at the age of two and a half. By the time he was
seven, he was performing public and private engagements with his musician father. For more than
20 years Ric has performed and traveled extensively throughout the United States and Europe,
delighting audiences with his unique playing style and music arrangements. He is equally
comfortable playing the organ, piano or keyboard, as a concert artist and product demonstrator.
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Drum/SFX Set ................................................... 39
Drums/SFX ....................................................... 38
A
Active Expression Voice ...................................... 35
Adjuster ............................................................ 22
Arrangement ................................................... 132
Arranger Function .............................................. 50
Arranger function ............................................... 46
Arranger Update .............................................. 109
Audio CD ........................................................ 104
Auto Std Tempo (Auto Standard Tempo) ............. 108
Automatic Accompaniment .............. 45–46, 50, 132
E
Ending ..................................................... 69, 132
Erase
Performance Song ......................................... 94
Exp. Source .................................................... 107
Expression Pedal ............................................... 71
Function ..................................................... 107
F
B
Factory Default Settings ...................................... 19
Factory Reset ..................................................... 19
Feet .................................................................. 31
Foot Switch ................................................. 68, 70
Format ............................................................ 120
Basic Chord .................................................... 132
Basic Pitch ....................................................... 114
Bass Split .......................................................... 86
Beat ............................................................... 112
Beat Indicator .................................................... 45
Break ................................................................ 69
G
General MIDI .................................................. 133
General MIDI 2 ............................................... 133
Glide ....................................................... 69, 132
GS ................................................................. 133
GS Format ...................................................... 133
C
CD-DA ............................................................ 104
Center Cancel ................................................. 104
Channel Mute .................................................. 114
Chord ............................................................. 132
Chord Intelligence .............................................. 48
Chorus ............................................................ 132
Composer ......................................................... 89
Composer Screen ............................................... 23
Computer ........................................................ 122
Connecting
H
Harmony Intelligence ......................................... 72
Headphones ..................................................... 18
I
Computer ................................................... 122
Contrast of the Screen ........................................ 20
Copying
Performance Song ....................................... 101
Registration ............................................. 65–66
Rhythm ................................................... 52–53
Rhythms on Disks into User Memory . 52, 101–102
cord hook ......................................................... 19
Count Down Sound .......................................... 108
Count In ............................................................ 93
Initial Touch .................................................... 106
Intro ......................................................... 69, 132
Inversion ......................................................... 132
K
Key Transpose ................................................... 67
L
LCD Contrast knob ............................................. 20
Leading Bass ............................................... 49, 69
Left Foot Switch ................................................. 69
Load
D
Damper Pedal .................................................... 68
Decay ............................................................... 68
Delete
Individual Registration .................................... 63
Performance Songs ........................................ 97
Set of Registrations ........................................ 62
Lower Keyboard ................................................ 26
Lower Voice ...................................................... 27
Lyrics .............................................................. 110
Performance Songs ........................................ 98
Registrations ................................................. 64
Rhythms Stored in User Memory ...................... 54
Demo Song ....................................................... 24
Demo Song List ................................................ 138
Display of Lyrics ............................................... 110
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Each Part Separately ..................................... 93
Performance ................................................. 91
Re-Recording ................................................ 94
Recording onto SMF ........................................... 99
Registration ............................................... 55, 132
Recalling ...................................................... 57
Storing ......................................................... 56
Registration Shift ................................................ 70
Rename
Performance Song ......................................... 95
Re-Recording ..................................................... 94
Reverb ............................................................ 132
Reverb Effect ..................................................... 77
Reverb Depth ................................................ 80
Reverb Type ................................................. 78
Wall Type .................................................... 79
Rhythm ............................................................. 40
fill-in ............................................................ 47
Starting and Stopping .................................... 69
Rhythm Screen ................................................... 23
Right Foot Switch ............................................... 69
Rotary ............................................................ 132
Rotary Effect ...................................................... 74
M
Master Tune .................................................... 114
Master Volume ................................................... 18
Metronome ...................................................... 111
Sound ........................................................ 112
Volume ....................................................... 111
Metronome Sound ............................................ 112
Metronome Volume .......................................... 111
MIDI ............................................................... 123
MIDI Devices
Connecting ................................................. 123
MIDI IN Mode ......................................... 116, 119
MIDI In/Out .................................................... 121
Music CD ........................................................ 104
Music Files ...................................................... 133
Music Rest ......................................................... 16
Mute ............................................................... 132
Muting
Channel ..................................................... 114
Track ......................................................... 113
O
Octave Shift ...................................................... 37
One Touch Program ........................................... 50
Others Button ..................................................... 29
S
Saving
Performance Songs ........................................ 96
Send PC Switch ............................................... 115
SMF Format ...................................................... 97
SMF Music Files ......................................... 90, 133
Track Assignment .......................................... 91
SMF with Lyrics ................................................ 133
Solo Mode ........................................................ 85
Solo To Lower Mode .......................................... 85
Solo Voice ........................................................ 28
Sound Generator ..................................... 132–133
Split ............................................................... 132
Split Point
Bass Split Point ............................................. 87
Solo Split Point .............................................. 85
Sustain ........................................................... 132
Sustain Effect
Sustain Length ............................................... 76
Synchro Start ............................................... 43, 50
P
Panel Reset ...................................................... 119
Panel Settings .................................................. 132
Part .................................................................. 26
Part Balance ...................................................... 36
Part Balance Monitor .......................................... 36
PC Number ..................................................... 115
Pedal Bass Mode ............................................. 106
Pedal Bass Voice ................................................ 27
Pedalboard ....................................................... 26
Percussion ......................................................... 33
Phones ............................................................ 121
jack ............................................................. 18
Pitch Bend ....................................................... 132
Playback Transpose .......................................... 110
Playing
Demo Song ................................................... 24
Performance Song ......................................... 92
Performance Songs Stored .............................. 90
Rhythm ......................................................... 42
Power Cord ....................................................... 17
Power On ......................................................... 17
T
Tempo .............................................................. 45
Track .............................................................. 113
Track Button ...................................................... 89
Track Mute ................................................ 91, 113
Trans. Update (Transpose Update) ..................... 109
Transpose
R
Recording
140
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Key Transpose ............................................... 67
Playing Back ............................................... 110
Tx MIDI Channel .............................................. 117
U
Upper Keyboard ................................................ 26
Upper Voice ...................................................... 27
USB ................................................................ 122
USB (MIDI) connector ....................................... 122
USB Driver ...................................................... 123
User Memory ............................................. 41, 119
User Memory Reset .......................................... 119
V
Variation ........................................................... 47
VARIATION DOWN .......................................... 69
VARIATION UP .................................................. 69
VIMA TUNES ........................................... 103, 133
Vintage Organ .................................................. 32
V-LINK ............................................................ 117
Voice ........................................................ 26, 132
Volume
Metronome ................................................. 111
Part Balance ................................................. 36
X
XGlite ............................................................. 133
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
PHILIPPINES
CURACAO
URUGUAY
NORWAY
JORDAN
AFRICA
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
Zeelandia Music Center Inc.
Orionweg 30
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
Roland Scandinavia Avd.
MUSIC HOUSE CO. LTD.
Kontor Norge
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
EGYPT
Al Fanny Trading Office
9, EBN Hagar Al Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: (022)-418-5531
Curacao, Netherland Antilles
TEL:(305)5926866
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
TEL: (02) 899 9801
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
TEL: 2273 0074
SINGAPORE
SWEE LEE MUSIC
COMPANY PTE. LTD.
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
KUWAIT
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Al-Yousifi Service Center
P.O.Box 126 (Safat) 13002
KUWAIT
VENEZUELA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
POLAND
ROLAND POLSKA SP. Z O.O.
UL. Gibraltarska 4.
PL-03 664 Warszawa
POLAND
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
TEL: (022) 679 4419
TEL: 00 965 802929
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
PORTUGAL
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
LEBANON
Chahine S.A.L.
George Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 16-
5857
Beirut, LEBANON
TEL: (01) 20-1441
REUNION ISLAND
TEL: (0262) 218-429
TEL:(593-4)2302364
SOUTH AFRICA
T.O.M.S. Sound & Music
(Pty)Ltd.
2 ASTRON ROAD DENVER
JOHANNESBURG ZA 2195,
SOUTH AFRICA
EUROPE
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final
Alameda Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
TEL: (02) 2561 3339
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
ROMANIA
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
THAILAND
Theera Music Co. , Ltd.
100-108 Soi Verng
OMAN
Austrian Office
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
TEL: (011)417 3400
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
Nakornkasem, New
TEL: 262-0788
Road,Sumpantawongse,
Bangkok 10100 THAILAND
TEL: (02) 224-8821
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
TEL: (266) 364 609
GUATEMALA
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
RUSSIA
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
QATAR
Al Emadi Co. (Badie Studio &
Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
AUSTRALIA/
NEW ZEALAND
TEL:(502) 599-2888
ASIA
CHINA
Roland Shanghai Electronics
SLOVAKIA
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
TEL: (014) 575811
DAN Acoustic s.r.o.
Povazská 18.
AUSTRALIA/
SAUDI ARABIA
aDawliah Universal
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
CROATIA
ART-CENTAR
Degenova 3.
HR - 10000 Zagreb
TEL: (1) 466 8493
SK - 940 01 Nové Zámky
TEL: (035) 6424 330
Electronics APL
Behind Pizza Inn
Prince Turkey Street
aDawliah Building,
PO BOX 2154,
Alkhobar 31952
SAUDI ARABIA
TEL: (03) 8643601
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
SPAIN
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
CZECH REP.
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
CZECH REPUBLIC
DISTRIBUTOR s.r.o
Voctárova 247/16
CZ - 180 00 PRAHA 8,
CZECH REP.
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
SWEDEN
SYRIA
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
TEL: (2) 830 20270
TEL: (010) 6426-5050
CENTRAL/LATIN
AMERICA
DENMARK
HONG KONG
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
TEL: (011) 223-5384
MEXICO
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
TURKEY
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
TEL: 3916 6200
TEL: 2415 0911
FINLAND
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
Parsons Music Ltd.
TEL: (55) 5668-6699
UKRAINE
EURHYTHMICS Ltd.
P.O.Box: 37-a.
Nedecey Str. 30
UA - 89600 Mukachevo,
UKRAINE
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Ground Floor, Dubai,
U.A.E.
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
BARBADOS
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
INDIA
Rivera Digitec (India) Pvt. Ltd.
411, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
TEL: (03131) 414-40
TEL: (04) 3360715
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
UNITED KINGDOM
TEL: (505)277-2557
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
NORTH AMERICA
PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE
PANAMA
GREECE/CYPRUS
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
UNITED KINGDOM
TEL: (01792) 702701
INDONESIA
PT Citra IntiRama
Jl. Cideng Timur No. 15J-15O
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
CANADA
Roland Canada Ltd.
(Head Office)
5480 Parkwood Way
Richmond B. C., V6V 2M4
CANADA
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
TEL: 315-0101
PARAGUAY
Distribuidora De
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (595) 21 492147
MIDDLE EAST
HUNGARY
TEL: (604) 270 6626
KOREA
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
BAHRAIN
Moon Stores
No.1231&1249 Rumaytha
Building Road 3931, Manama
339 BAHRAIN
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
Roland Canada Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (23) 511011
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
TEL: 17 813 942
TEL: (574)3812529
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
MALAYSIA
TEL: (905) 362 9707
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
IRAN
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
COSTA RICA
JUAN Bansbach Instrumentos
Musicales
Ave.1. Calle 11, Apartado
10237,
San Jose, COSTA RICA
TEL: 258-0211
U. S. A.
Lima - Peru
TEL: (511) 4461388
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TRINIDAD
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868) 638 6385
TEL: (021)-2285-4169
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
VIET NAM
Suoi Nhac Company, Ltd
370 Cach Mang Thang Tam St.
Dist.3, Ho Chi Minh City,
VIET NAM
TEL: (323) 890 3700
ISRAEL
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'alia Hashnia St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
TEL: 9316540
As of Oct. 1, 2007 (ROLAND)
Download from Www.Somanuals.com. All Manuals Search And Download.
For EU Countries
For China
Download from Www.Somanuals.com. All Manuals Search And Download.
For EU Countries
For the USA
This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
AT-100 / AT-300
Digital Organ
Type of Equipment :
Responsible Party : Roland Corporation U.S.
Address : 5100 S. Eastern Avenue, Los Angeles, CA 90040-2938
(323) 890-3700
Telephone :
*
0
5
1
2
0
8
2
3
-
0
2
*
05120823
08-05-2N
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|