Copyright 2009 ROLAND CORPORATION
©
All rights reserved. No part of this publication may be reproduced in any
form without the written permission of ROLAND CORPORATION.
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES.”
These sections provide important information concerning the proper operation of the unit. Additionally, in order to
feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should
be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
Setup Guide
Check the included items
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
Stand (MDS-4)
TD-4K parts
01
02
The parts required to
assemble the stand (MDS-4)
are listed in the MDS-4
Owner’s Manual.
Check the owner’s manual
and make sure that you
have all of the parts.
Manual set
□ AC adaptor
□ Setup Guide (this document)
□ Owner’s Manual
□ Hi-hat control
pedal (FD-8)
□ Kick trigger pad
(KD-8)
□ Cymbal pad for
□ Cymbal pad for
crash/ride
□ V-Pad for snare
□ Pad for tom
(PD-8 x 3)
□ Drum sound
□ Connection cable
□ Drum key
hi-hat (CY-5)
(PDX-8)
module (TD-4)
(special for TD-4)
(CY-8 x 2)
Attach the crash cymbal (CY-8) and ride cymbal (CY-8)
Assemble the stand
Attach the parts
Tighten the bolt with
a drum key.
Assembly procedure
*
The parts required for mounting the cymbals and the
hi-hat are included in the TD-4K attachment box.
03
Wing nut
Assemble the stand using the procedure described in the MDS-4 Owner’s
Manual.
Rotation stopper
(note orientation)
Tighten the wing
nut to obtain an
appropriate amount
of sway.
Felt washer
Attach the bolt so that
it is at the right when
seen by the performer.
Attach the hi-hat (CY-5)
Upper clutch
Clutch felt (small)
Attach the sound module (TD-4)
Cymbal mounts
Pad mounts
*
The wingnut screws
Clutch felt (large)
Lower clutch
needed for accomplishing the
installation using the sound
module mounting plate
were packed inside the bag
containing the AC adaptor.
Attach the snare (PDX-8) and
toms (PD-8)
Tighten
Loosen
Tighten
Loosen
Hi-hat mount
Rod
Rod
Align with indentation
While pressing
Pad mounts
Adjusting the tension (PDX-8)
If the stand wobbles,
loosen this hand
knob and adjust the
height.
Use Drum Key
to tighten
6
1
4
3
2
5
Assemble the hi-hat control pedal (FD-8)
Assemble the kick (KD-8)
1. Finger-tighten all six of the tuning bolts in
the sequence shown in the illustration.
Attach the anchor bolt
(if installing on a drum mat)
Adjusting the pedal depth
*
For reasons of safety, do not spread the
stand wider than 1.0 meters (40 inches).
Loosen with the drum key,
and tighten after adjusting
2. The appropriate amount of tension is one
that will provide approximately the same
striking response as on an acoustic drum.
Anchor bolt
Anchor bolt
Deeper
Spring for
the anchor bolt
3. Use the drum key to adjust the tension as
needed.
Slide the arm
Remove the stand fastening
screws from the reverse side
of the KD-8’s trigger.
Pull out the stand in the
direction of the arrow, and
use the screws you removed
earlier to fasten the stand.
1.0 m (40”)
Shallower
Connect the pads to the sound module
Connect the AC adaptor and speakers
* To prevent malfunction and/or damage to
speakers or other devices, always turn down
the volume, and turn off the power on all
devices before making any connections.
CR1
04
05
RD
*
Use cable ties to fasten
the cables at the circled
locations “ ” so that they
do not interfere with your
performance.
Connection procedure
T2
T1
Stereo
Headphones
HH
AC adaptor
Indicator
TD-4
KIK
SNR
T3
Make sure to wrap the cable
ties around the pipes.
Stereo
1/4” plug
Power cable
CR2
*
Do not connect the CR2
cable (for extension). Leave
the cap in place, and fasten
the cable so that it will not
hinder your performance.
1. Connect the cable to
2. Labels indicating the pad to be
connected are attached to the
cable. Connect the cable to the
OUTPUT jack of each pad as
shown in the illustration.
1/4” plug (mono)
*
*
To prevent the inadvertent disruption of power to your unit
(should the plug be pulled out accidentally), and to avoid
applying undue stress to the AC adaptor jack, use cable ties to
fasten the cord from the AC adaptor to the stand.
the TD-4 as shown in
the illustration.
to AC outlet
HHC
Amplified
speakers, etc.
If you’re working in mono, only use the L/MONO jack.
■ When you’ve finished making connections, turn on the power as described in the TD-4 Owner’s
This completes assembly and connections.
Manual, and verify that you can hear sound.
Detailed explanation of each part
*
Use a commercially available kick pedal.
*
To prevent damage to the floor or carpet and to ensure stability, we recommend that you use a drum mat (TDM series; sold separately).
■ KD-8 (Kick)
Extend the stand and fasten it
Attach the kick pedal
NOTE
01
02
When using a twin pedal
*
*
*
Install the kick pedal securely.
Position the two beaters equally apart from
the center of the pad as shown in the figure
at left. If one of the beater is further away
from the center than the other, the sound
from the further beater will be lower in
volume, or will not sound as desired.
Using a twin pedal will result in lower sen-
sitivity as compared to when a single pedal
is used. Raise the sensitivity on the sound
module (TD-4) by following the instructions
given in “TD-4 Owner’s Manual.”
Position the beater so that it strikes
the center of the head, then secure the
kick pedal and KD-8 firmly in place.
Take care not to pinch your fingers.
The tips of the anchor bolts are sharp.
Handle with care.
*
When moving the KD-8, be sure to remove
the screws and fold the stand. Transporting
the KD-8 while it remains open may subject
the stand to excessive strain and result in
damage to the stand.
Beater
1. Remove the stand fastening screws
from the reverse side of the KD-8’s
trigger.
2. Pull out the stand in the direction
indicated by the arrow until it is fully
extended.
3. Using the drum key included in the
FD-8 packing carton, tighten the screws
removed in Step 1 so that the stand is
firmly secured.
*
Anti-skid tape is affixed to the foot plate.
When transporting the KD-8, don’t forget
to pick up the foot plate.
Install the kick
pedal securely.
KD-8 component names
Output jack
Adjust the height of the foot plate
Head
03
This height will vary depending
on your kick pedal.
Beater
Stand
Commercially available kick pedal
Anchor bolt
When using on
hard-surfaced ꢀooring
When using on the drum mat
*
Adjust the height so that the entire pedal
comes into contact with the ꢀoor.
1. Loosen the anchor bolts and temporarily remove the foot
plate.
3. Turn the anchor bolts to adjust the height so that the entire kick
pedal is in contact with the floor and that the KD-8 does not
wobble even when you press the pedal to make the beater strike
the pad.
4. Screw the anchor bolts into the screw holes of the foot plate to fasten it.
If you’re using a drum mat, the KD-8 will be more stable if the pointed
portion of the anchor bolts protrudes from the foot plate. If you’re not
using a drum mat, take care not to tighten the anchor bolts too far, so
that you do not damage the floor or carpet.
2. Place the KD-8 and the kick pedal on the floor. Position the
foot plate so that the anchor bolts rest on the screw holes
of the foot plate.
When adjusting the height, lift the stand slightly while turning the
anchor bolts so that the foot plate is not fastened together with it.
Foot plate
Other side
Download from Www.Somanuals.com. All Manuals Search And Download.
|