REMOTE CONTROL
OPERATING INSTRUCTIONS
918-582a
07/11/06
© Copyright 2006, FPI Fireplace Products International Ltd. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Matching Remote Handset & Control Box ID Code.......................................................... 4
Remote Control Keypad ..................................................................................................... 5
Remote Control Screen Display (LCD).............................................................................. 6
Quick Reference of Basic Functions................................................................................... 7
Switching the Remote ON and OFF.............................................................................. 7
Setting Time & Day ...................................................................................................... 7
Manual and Auto Mode ................................................................................................ 8
Displaying Temperature in Celsius or Fahrenheit ........................................................ 8
Manual Mode ..................................................................................................................... 9
Fan Speed Adjustment................................................................................................... 9
Flame Height Adjustment............................................................................................ 10
Auto Mode ........................................................................................................................ 11
Program Mode .................................................................................................................. 12
Setting the Program Mode ................................................................................................ 13
Interfacing with Manual Control ...................................................................................... 18
Troubleshooting / Battery Replacement ........................................................................... 18
Special Conditions in Program Mode.......................................................................... 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Matching Remote Handset and Control Box ID Code
The Remote Control Handset has a set of unique ID codes that is pre-programmed into its
memory. This set of ID codes helps to differentiate one Remote Control Handset from
another so that only the control box with a matching ID code will respond to the
appropriate Remote Control Handset.
To ensure the remote control is matched to the receiver correctly, please follow the steps
below:
1. Ensure that the Remote Control and the 3-way switch located at the appliance are
both in the OFF position.
2. Ensure that the pilot is lit and the pilot control knob is in the ON position on the
appliance.
3. Install the 2 x AAA alkaline batteries into the Remote Control.
4. Unplug and re-plug the power cord. The power cord is located on the left hand
side of the appliance and will be plugged into the receptacle.
5. Switch the 3-way switch located on the appliance to the REMOTE position.
6. Press and hold the PROG and FAN buttons simultaneously for up to 20 seconds.
During this time, the remote will display LC while it is transmitting codes to the
receiver. Once it is successfully transmitted, one will hear the solenoid click and
the burners will come on. If is does not work the first time, repeat steps 1 - 6.
7. Release both the PROG and FAN buttons. The remote will revert back to normal,
but the burner will still be on.
8. Press the ON/OFF button on the remote control 2 times to turn the burner off.
9. The remote control is now programmed to the receiver and the appliance can now
be operated with it.
The control box will only learn the Remote ID codes during the first 30 seconds after
power is applied and will ignore this special command from the Remote after the first 30
seconds.
NOTE: This must only be performed by a qualified installer.
TM
Page 4
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The FireWizardTM Remote Control was developed to provide a user-friendly system to
operate your appliance. The operating range is approximately 10 metres (32 feet).
A Quick Reference Sticker is available to be placed on the back of your remote control
handset. Place the sticker close to the very top of the remote, away from the battery
opening and wall mounting bracket.
REMOTE CONTROL KEYPAD
There are 7 push buttons on the Remote Control:
(1) ON/OFF Button: Switches the Remote & Control Box ON or OFF;
(2) “+” Button: This is the INCREMENT or HOUR button;
(3) “-” Button: This is the DECREMENT or MINUTE button;
(4) AUTO/MAN Button: Toggles between Manual, Auto and Program mode;
(5) TIME Button: Initiates the setting of the Time and Day;
(6) PROG Button: Initiates the programming of Auto mode;
(7) FAN Button: Changes the speed of the fan;
(1) On/Off Button
(2) “+” Button
(4) Auto/Man Button
(6) Prog Button
(3) “-” Button
(5) Time Button
(7) Fan Button
TM
FPI FireWizard Remote Control Manual
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL SCREEN DISPLAY (LCD)
The LCD provides the following display features:
1. Flame Height Indication;
2. Manual & Auto Mode Indication - “MANUAL” / “AUTO”;
3. “ROOM” or “SET” Temperature Indicator;
4. Day of the Week;
5. Transmit Indicator “
6. System Status Indicator “ON” or “OFF”;
7. Battery Low Indicator “
” ;
”
8. Programmed Mode Indication “PROG 1” / “PROG 2”;
9. Temperature Display in “ºC” or “ºF”;
10. Fan Speed Indication;
11. Time of Day with AM, PM;
TM
Page 6
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC FUNCTIONS
OF THE REMOTE CONTROL
For the remote to function it must be turned ON. However when the remote is OFF, the
LCD continues to display the current day, time and room temperature.
Switching the Remote ON & OFF
The On/Off button is used to switch the Remote ON or OFF.
If the Remote is switched OFF, pressing and releasing the On/Off button will switch ON
the Remote (and the FireWizardTM Control Box). Once switched ON, the Remote will
continue with its last selected operating mode, for example, Manual, Auto or Program
mode.
Setting Time & Day
Note: The remote control needs to be “ON” in order to set the Time & Day.
Time
Press and hold the “TIME” button for 2 seconds and then use the “+” button to set
the hour and use the “-” button to set the minute.
Day
Immediately after setting the time, press the “TIME” button again and use the “+”
or “-” button to set the day.
Press the “TIME” button once more to record the setting.
TM
FPI FireWizard Remote Control Manual
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual & Auto Mode
Press the “Auto/Man” button to toggle from Auto, Manual & Program mode. See
“Setting the Program Mode” for details on Program Mode.
Manual
In Manual Mode using the “+” or “-” button allows you to adjust the flame height
accordingly. There are seven different levels of flame settings.
Use the “Fan” button to adjust the fan speed. There are 3 different fan speed
settings.
Auto
In Auto Mode using the “+” or “-” button allows you to change the Set
Temperature.
Use the “Fan” button to adjust the fan speed. There are 3 different fan speed
settings.
Displaying Temperature in Celsius or Fahrenheit
The default setting of the Remote is to display the temperature in Celsius.
However, the Remote can be changed to display temperature in Fahrenheit by the
following steps:
1. Ensure the Remote is switched off by using the On/Off button.
2. Press and hold the “-” button.
3. While the “-” button is held down, press and release the “+” button, this will
toggle the temperature display between °C and °F.
This setting is stored in memory hence the Remote will continue to display the
temperature in Fahrenheit even if the battery is replaced.
TM
Page 8
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL MODE
Manual mode can be selected by pressing and releasing the AUTO/MAN button until the
symbol “MANUAL” is shown on the LCD.
In Manual mode, the Fan speed and Flame settings can be adjusted independently using
the Remote.
FAN Speed Adjustment
The FAN button is used to switch on and change the selected fan speed.
If the Fan is off, pressing and releasing the FAN button once will turn the fan on at High
speed for 4 seconds and then to Low speed.
Pressing and releasing the FAN button again will change the speed to Medium.
Pressing and releasing the FAN button again will change the speed to High.
Pressing and releasing the FAN button again will switch the Fan OFF.
The display on the LCD will be as follows:
Fan on Low Speed
Fan on Medium
Speed
Fan on High Speed
Fan = OFF
TM
FPI FireWizard Remote Control Manual
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Flame Height Adjustment
There are seven levels of flame settings that can be selected manually using the “+” and
“-” button.
Pressing and releasing the “+” button once will increase the flame to a higher setting.
Continuously holding down the “+” button will increase the flame gradually until it has
reached the highest setting.
Conversely pressing and releasing the “-” button once will decrease the flame to a lower
setting.
Examples of the display on the LCD are as follows:
Flame Setting = 1
Flame Setting = 3
Flame Setting = 7
When the unit is turned on, the flame height is set to Hi for 20 seconds by default. After
20 seconds, the flame will revert to the setting prior to being turned off.
When the flame setting is at the lowest level (1), the flame indicator will blink on the
handset, the rear burner will turn off, and the front burner will default to the highest
setting. If the “+” button is pressed, the rear burner will turn on and the flame can
continue to be increased.
TM
Page 10
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO MODE
In Auto Mode the remote will adjust the flame setting and fan speed according to the
temperature difference between the Set Temperature and the Room Temperature.
When the set temperature is higher than the room temperature by more than
2.5°C (4.5°F), the flame will be at the highest setting (7) and the fan speed will
default to the lowest setting (1).
As the set temperature approaches room temperature, the flame level will reduce
accordingly. When the set temperature is equal to the room temperature, the
flame will stay at the lowest setting, and the fan will turn off.
Once the room temperature is higher than the set temperature by 2°C (3.6°F), the
flame will turn OFF.
Auto mode can be selected by pressing and releasing the AUTO/MAN button until the
symbol “AUTO” is shown on the LCD.
In Auto mode, when either the “+” or “-” button is pressed, the Set Temperature will be
displayed on the LCD instead of the Room Temperature. The Set Temperature will
remain displayed on the LCD for 5 seconds after the button is released and then the
display will revert to show the Room Temperature. The Set Temperature can be adjusted
while it is displayed using the “+” and “-” buttons.
The LCD will show the following when either the “+” or “-” button is pressed:
Room
Temperature
Set
Temperature
Auto Mode normal
display
When “+” or “-”
button is pressed
TM
FPI FireWizard Remote Control Manual
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
PROGRAM MODE
Program mode is selected by pressing and releasing the AUTO/MAN button until the
symbol “PROG” is shown on the LCD. The Remote will operate according to the settings
in the 2 Programs set by the user. Refer to Setting the Program Mode for details.
Pressing and releasing the “+” or “-” button in this mode will cause the temperature
displayed on the LCD to change from showing the Room Temperature to show the Set
Temperature. The Set Temperature will remain displayed on the LCD for 5 seconds after
the button is released and then the display will revert to show the Room Temperature.
Room
Temperature
Set
Temperature
Program 1 mode
normal display
When “+” or “-”
button is pressed
Pressing and releasing the PROGRAM button successively will allow the user to review
the programmed times for each day of the week.
If the Programs have not been programmed in the Remote, the display will show the
following:
Programs have not been set.
TM
Page 12
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE PROGRAM MODE
It is recommended to unplug the unit while setting the programs.
In this mode, the user can program two On-Times and two Off-Times as well as the
Temperature settings for each day of the week. The PROG button is used to initiate the
programming mode. The “+” and “-” buttons are used to adjust the time and temperature
settings.
Note: The remote needs to be ON in order to set the Programs.
Follow the steps below to set the programs:
1) Programming the On-Time of Program 1
Press and hold the PROG button for 2 seconds or more to initiate the
Programming mode.
The symbol “PROG 1” will flash to indicate the Remote is in Programming mode.
The On-Time for Program 1 will also flash. The “+” and “-” buttons can be used
to adjust this time setting.
The LCD will show the current setting in Program 1 for Monday:
Programming of Program 1
Program 1 On-Time
TM
FPI FireWizard Remote Control Manual
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2) Programming the Off-Time of Program 1
Press and release the PROG button again to program the Off-Time for Program 1.
Use the “+” and “-” buttons to adjust this time setting.
The LCD will show the following:
Programming of Program 1
Program 1 Off-Time
3) Programming the Set Temperature for the On-Time of Program 1
Press and release the PROG button again to program the Set Temperature. Use
the “+” and “-” buttons to adjust the temperature setting.
Program 1 Set Temperature
Programming of Program 1
TM
Page 14
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Programming the On-Time of Program 2
Press and release the PROG button again to program the On-Time of Program 2.
Use the “+” and “-” buttons to adjust this time setting.
The LCD will show the following:
Programming of Program 2
Program 2 On-Time
5) Programming the Off-Time of Program 2
Press and release the PROG button again to program the Off-Time of Program 2.
Use the “+” and “-” buttons to adjust this time setting.
The LCD will show the following:
Programming of Program 2
Program 2 Off-Time
TM
FPI FireWizard Remote Control Manual
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
6) Programming the Set Temperature for the On-Time of Program 2
Press and release the PROG button one more time to program the Set
Temperature of Program 2. Use the “+” and “-” buttons to adjust the temperature
setting.
Program 2 Set Temperature
Programming of Program 2
7a) Programming the Rest of the Week
Repeat steps 2 to 6 until all 7 days have been programmed.
7b) Alternatively, Copy Programs Over to the Other Days
Pressing and holding the PROG button for 2 seconds or longer will initiate the
copying process.
The next Day of Week flashes
Program 1 Setting of Monday
TM
Page 16
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Pressing and releasing the “+” button will select the Day(s) of which the program
is to copy to.
Pressing and releasing the “-” button will confirm the copying process in which
the original program will copy across to the selected day(s).
The next Day of Week flashes
Program 1 Setting of Monday and
Tuesday
After the program is copied, the selected days will remain lit and the following day will
start to flash.
Press and release the PROG button to return to normal programming mode.
8) Exiting Programming Mode
The Remote will automatically exit the Programming mode 20 seconds after the
last button is released.
TM
FPI FireWizard Remote Control Manual
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
INTERFACING WITH MANUAL CONTROL
When the unit is turned ON using the Remote Control and is later switched OFF from the
Manual Control Panel, the LCD on the Remote Control will still display as being ON
even though the unit is actually OFF. To have the unit function from the Remote Control
again you must press the ON/OFF button twice -- once to turn the remote OFF and then
again to turn the unit ON from the remote.
When the unit is turned ON from the Manual Control Panel, the LCD on the Remote
Control will display as being OFF even though the unit is actually ON. To have the unit
function from the Remote Control you will need to press the ON/OFF button once to turn
ON the remote.
TROUBLESHOOTING / BATTERY REPLACEMENT
If the remote control does not turn on:
• Ensure the batteries are correctly installed in the receiver.
• Check the batteries for replacement (2 x AAA alkaline).
When batteries are replaced, only the current time and day will need to be reset. The set
program times are not affected.
TM
Page 18
FPI FireWizard Remote Control Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Conditions in Program Mode
o If the On-Time of a Program matches the Off-Time of the same Program, the
Program is disabled.
o If the Off-Time of the first Program crosses over to the On-Time of the second
Program, the Off-Time of the first Program will have precedent, for example,
if Program 1 is programmed to end at 2:00 pm whereas Program 2 is
programmed to commence at 1:00 pm, the following will occur:
Program 1
On-Time
8:00 am
Off-Time
2:00 pm
1:00 pm
4:00 pm
On-Time
Off-Time
Program 2
Operates under Program 2 Setting
Operates under Program 1
Setting
TM
FPI FireWizard Remote Control Manual
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
FireWizard is a trademark of FPI Fireplace Products International Ltd.
Printed in Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|