Regency Indoor Fireplace P121 User Guide

P121 / P121LC / P121RC / P131

Zero Clearance Direct Vent Gas Fireplace

Owners &

Installation Manual

STYLE

SeeThru

LeftCorner

MODEL

P121-NG1NaturalGas

P121LC-NG1NaturalGas P121LC-LP1Propane

P121-LP1Propane

RightCorner P121RC-NG1NaturalGas P121RC-LP1Propane

Pier P131-NG1NaturalGas P131-LP1Propane

WARNING:

FORYOURSAFETY

What to do if you smell gas:

Do not try to light any appliance

Do not touch any electrical switch: do not use any

phone in your building.

Immediately call your gas supplier from a neighbour's

phone. Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire

department.

If the information in these instructions are not followed

exactly, a fire or explosion may result causing property

damage, personal injury or loss of life.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapours and

liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualified

installer, service agency or the gas supplier.

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

918-107a

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

08/08/03

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Safety Label

SafetyLabel ............................................................... 4

Installation

Operating Instructions

OperatingInstructions ...............................................29

LightingProcedure ....................................................29

ShutdownProcedure .................................................29

First Fire ...................................................................29

AerationAdjustment..................................................29

NormalOperatingSoundsof

ManufacturedMobileHomeRequirements ................. 2

ImportantMessage .................................................... 5

Before You Start ........................................................ 5

GeneralSafetyInformation ......................................... 5

Installation Checklist .................................................. 5

Specifications ............................................................ 6

LocatingYourFireplace ............................................. 8

Clearances ................................................................. 9

CombustibleMantelClearances ................................. 9

FramingandFinishing ...............................................10

FacingandFinishingRequirements ..........................11

Unit Assembly Prior to Installation

TopStandoffAssembly .......................................11

VentingIntroduction ..................................................11

ExteriorVentTerminationLocations..........................12

Venting: Direct Vent System (Flex) ...........................13

Venting: Simpson Dura Vent Direct Vent GS ............14

Venting: Simpson Dura Vent Components List..........14

VentingArrangements

Gas Appliances ..................................................29

Lighting Plate Instructions .........................................30

Maintenance

MaintenanceInstructions ..........................................30

GeneralVentMaintenance ........................................31

LogReplacement ......................................................31

Thermopile/Thermocouple .........................................31

Glass Gasket............................................................31

DoorGlass................................................................31

Gold-PlatedAccessories...........................................31

RemovingValve .........................................................31

InstallingValve ..........................................................32

FanReplacement ......................................................33

PartsList

HorizontalTerminations ......................................15

VerticalTerminations ..........................................17

Venting-Dura-VentHorizontalInstallations ..............19

Venting-Dura-VentVerticalTermination...................20

Venting - Installation Procedures for Direct Vent

Replacement/SparePartsList...................................34

Warranty

System (Flex) .....................................................21

ConveriontoPropane ................................................22

System Data .............................................................23

HighElevation ...........................................................23

Gas Line Installation..................................................23

Pilot Adjustment .......................................................23

Gas Pipe Pressure Test ............................................23

Warranty ...................................................................39

SITValveDescription ................................................23

Log Set Installation ...................................................24

GlassDoorRemoval..................................................26

FinishingTrim ...........................................................26

LouversandGrills......................................................26

RemoteControl(optional) ..........................................27

Remote Wall Switch (optional) ..................................27

WallThermostat(optional) ........................................27

WiringDiagram .........................................................28

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY LABEL

This is a copy of the label that accompanies

eachP121-1/P121LC-1/P121RC-1/P131-1Zero

Clearance Direct Vent Gas Fireplace. We have

printed a copy of the contents here for your

review. The safety label is located on the front

inside base of the unit, visible when the bottom

louver is open.

NOTE: Regency units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is the

correct one.

For the State of Massachusetts, installation

and repair must be done by a plumber or

gasfitter licensed in the Commonwealth of

Massachusetts.

For the State of Massachusetts, flexible

connectors shall not exceed 36 inches in

length.

For the State of Massachusetts, the appli-

ances individual manual shut-off must be a

t-handle type valve.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

free of combustible materials, (gases and

other flammable vapours and liquids).

IMPORTANT:

SAVE THESE

INSTRUCTIONS

YOUNG CHILDREN SHOULD BE

CAREFULLY SUPERVISEDWHENTHEY

AREINTHESAMEROOMASTHEAP-

PLIANCE.

Emissions from burning wood or gas could

contain chemicals known to the State of

California to cause cancer, birth defects or

other reproductive harm.

The Panorama P121/P121LC/P121RC/P131-

NG1orP121/P121LC/P121RC/P131-LP1Direct

Vent Fireplace must be installed in accordance

with these instructions. Carefully read all the

instructions in this manual first. Consult the

"authority having jurisdiction" to determine the

needforapermitpriortostartingtheinstallation.

It is the responsibility of the installer to ensure

this fireplace is installed in compliance with

manufacturer's instructions and all applicable

codes.

GENERAL SAFETY

INFORMATION

INSTALLATION

CHECKLIST

1) The appliance installation must conform

with local codes or, in the absence of

local codes, with the current Canadian or

NationalGasCodes,CAN1-B149orANSI

Z223.1 Installation Codes.

Note: These units are

non-load bearing.

2) See general construction and assembly

instructions. Theapplianceandventshould

be enclosed.

1) Locate appliance

a) Room location, page 8.

b) Clearances to Combustibles,

page 9.

c) Mantle Clearances, page 9.

d) Framing & Finishing Requirements,

page 10.

BEFORE YOU START

3) This appliance must be connected to the

specified vent and termination cap to the

outside of the building envelope. Never

vent to another room or inside a building.

Make sure that the vent is fitted as per

Venting instructions.

Safe installation and operation of this appliance

requires common sense, however, we are

required by the Canadian Safety Standards

and ANSI Standards to make you aware of the

following:

e) Venting Requirements, pages 11-19.

2) Assemble Top Standoffs, page (NOTE:

page11mustbedonebeforeinstallingunit

into fireplace.)

INSTALLATIONANDREPAIRSHOULD

BE DONE BY A QUALIFIED SERVICE

PERSON.THEAPPLIANCESHOULDBE

INSPECTED BEFORE USE AND AT

LEASTANNUALLYBYAPROFESSION-

ALSERVICEPERSON.MOREFREQUENT

CLEANINGMAYBEREQUIREDDUETO

EXCESSIVELINTFROMCARPETING,

BEDDINGMATERIAL,ETC.ITISIMPER-

ATIVE THAT CONTROL COMPART-

MENTS,BURNERSANDCIRCULATING

AIR PASSAGEWAYS OF THE APPLI-

ANCEBEKEPTCLEAN.

4) Inspect the venting system annually for

blockage and any signs of deterioration.

3) Install vent, pages 19-21.

5) Ventingterminalsshallnotberecessedinto

a wall or siding.

4) Makegasconnections. Testthepilot. Must

be as per diagram. Page 22.

6) Any safety glass removed for servicing

must be replaced prior to operating the

appliance.

5) Install log set where indicated on

page 24-25.

7) To prevent injury, do not allow anyone who

is unfamiliar with the operation to use the

fireplace.

6) Glass Door Removal (page 26), Louvers

or Grills (page 26), and Finishing Trim

(page 26).

8) Wear gloves and safety glasses for pro-

tection while doing required maintenance.

7) Install optional Wall Switch, Remote Con-

trol, or Wall Thermostat, page 27.

DUE TO HIGH TEMPERATURES, THE

APPLIANCESHOULDBELOCATEDOUT

OFTRAFFICANDAWAYFROMFURNI-

TUREANDDRAPERIES.

9) Be aware of electrical wiring locations in

walls and ceilings when cutting holes for

termination.

8) Final check.

Before leaving this unit with the customer, the

installermustensurethattheapplianceisfiring

correctly and operation fully explained to cus-

tomer.

WARNING:FAILURETOINSTALLTHIS

APPLIANCECORRECTLYWILLVOID

YOURWARRANTYANDMAYCAUSEA

SERIOUSHOUSEFIRE.

10) Under no circumstances should this appli-

ance be modified. Parts that have to be

removed for servicing should be replaced

prior to operating this appliance.

This includes:

11) Installationandanyrepairstothisappliance

should be done by a qualified service per-

son. A professional service person should

be called to inspect this appliance annually.

Make it a practice to have all of your gas

appliances checked annually.

CLOTHINGOROTHERFLAMMABLEMA-

TERIALSHOULDNOTBEPLACEDON

ORNEARTHEAPPLIANCE.

1) Clocking the appliance to ensure the cor-

rect firing rate (rate noted on label 40,000

Btu/hNG, and39,000Btu/hLP)afterburn-

ing appliance for 15 minutes.

CHILDRENANDADULTSSHOULDBE

ALERTEDTOTHEHAZARDSOFHIGH

SURFACETEMPERATURES,ESPECIAL-

LY THE FIREPLACE GLASS, AND

SHOULDSTAYAWAYTOAVOIDBURNS

ORCLOTHINGIGNITION.

2) If required, adjusting the primary air to

ensure that the flame does not carbon.

First allow the unit to burn for 15-20 min.

to stabilize.

12) Do not slam shut or strike the glass door.

13) Under no circumstances should any solid

fuels (wood, paper, cardboard, coal, etc.)

be used in this appliance.

CAUTION: Any alteration to the product

that causes sooting or carboning that

results in damage is not the responsi-

bility of the manufacturer.

14) The appliance area must be kept clear and

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

SPECIFICATIONS

P121-1 See Thru

Note: These units are

non-load bearing.

P131-1 Pier

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

P121LC-1 Left Corner Unit

Note: These units are

non-load bearing.

P121RC-1RightCornerUnit

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

LOCATING YOUR

GAS FIREPLACE

A) P121-1 See Thru

1) When selecting a location for your stove,

ensure that the clearances are met as

outlined on page 9.

2) Provide adequate clearances for servic-

ing.

3) The appliance must be installed on a flat,

solid, continuous surface (e.g. wood, met-

al, concrete). This may be the floor, or

raised up on a platform to enhance its

visualimpact. Iftheapplianceisgoingtobe

installed on carpeting, combustible linole-

um tile or other combustible material other

than wood flooring, the appliance must be

installed on a metal or wood panel extend-

ing the full width and depth of the appli-

ance.

4) The Direct Vent Gas Fireplace can be

installed as follows:

Model # Position

P121-1: See Thru

P131-1:Pier

B) P131-1 Pier

P121LC-1: Left Corner

P121RC-1: Right Corner

5) ThisapplianceisListedforbedroom instal-

lations when used with a Listed Millivolt

Thermostat. Some areas may have further

requirements, check local codes before

installation.

6) The P121-1/P121LC-1/P121RC-1/P131-1

Direct Vent Gas Fireplace is approved for

alcove installations, which meet the clear-

ances listed on this page.

7) We recommend that you plan your instal-

lation on paper using exact measurements

for clearances and floor protection before

actually installing this appliance. Have a

qualified inspector, dealer, or installer re-

view your plans before installation.

C) P121LC-1 Left Corner

Note: For Exterior Vent Termination

Locations see page 12.

D) P121RC-1 Right Corner

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

CLEARANCES

The clearances listed below are Minimum distances unless otherwise stated (refer to diagrams on page 8):

Clearance to Combustibles from:

Back

Side

Floor

(0mm)

WARNING:

Fire hazard is an extreme risk

if these clearances (air space)

to combustible materials are

not adhered to. It is of greatest

importance that this fireplace

and vent system be installed

only in accordance with these

instructions.

CAUTION REQUIREMENTS: The top, back and sides of the fireplace are defined by

standoffs. The metal ends of the standoffs may NOT be recessed into combus-

tible construction.

Determine the total thickness of the finished floor (eg. tile, carpet, slate) to allow

the finished surface to be flush with the base of the unit.

Ceiling Height from Floor 72" (1828mm)

Mantel Height from Base of Unit:

39" min. (991mm)

Horizontal Vent Clearances:

Top

Side

Bottom

2-1/2"(64mm)

1-1/2"(38mm)

Vertical Vent Clearances 1-1/4" (32mm)

COMBUSTIBLE MANTELS

Mantel Clearances

Because of the extreme heat this fireplace emits, the mantel clearanc-

es are critical. Combustible mantel clearances from top of unit are shown in

Diagram to the right.

Note: A non-combustible mantel may be installed at a lower height if

the framing is made of metal studs covered with a non-

combustible board.

This drawing is to scale at 1:6 (one inch = 6 inches)

Mantel can be installed anywhere in shaded area or higher using this scale.

Caution: Ensure the paint that is used on the mantel and the facing is

"heat resistant" or the paint may discolour.

* If the 3" metal extension trim is removed it must be replaced with a 3" non-

combustible material.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

FRAMING AND FINISHING

1) For ease of installation, frame your fireplace after it is positioned and

the vent system is installed. Remember to install the top standoffs.

See page 11 for assembly. Use 2x4's and frame to local building

codes.

FramingDimensions

P121-1 (See Thru)

P131-1 (Pier)

P121LC-1 / P121RC-1

(Corner Unit)

25"(635mm)

minus two times

the finishing

25"(635mm)

minus two times

the finishing

26-13/16"

minus one time

the finishing

CAUTION: Verify your fireplace dimensions, framing methods

and finished wall facing details before framing. Determine the

total thickness of facing material - drywall plus ceramic tiles,

slate, etc. Allow the finish surface to be flush with the front or

side of the unit. Total facing thickness can vary from 1/2"

(13mm) to 1-1/4" (32mm) thick.

material thickness* material thickness* material thickness*

42-1/2"(1080mm) 42-1/2"(1080mm) 42-1/2"(1080mm)

46-3/4"(1187mm) 45" (1143mm)

minus one time

45"(1143mm)

minus one time

the finishing

2) When locating your appliance on an exterior wall or in a chase, apply

a vapour barrier and drywall, as per local building codes. DO NOT

INSULATETHEFIREPLACEITSELF.

the finishing

material thickness* material thickness*

CAUTION: The unit does not have to be completely enclosed in

a chase. The clearance on top of the unit is 0" to the standoffs

so combustible building materials can be laid directly on top of

the standoffs. You must maintain clearance from the vent to

combustible materials for both rigid and flex, see Vent Clear-

ances, page 9.

* Finish material thickness includes: drywall, ceramic tile, slate, etc.

P121LC-1 - Corner Unit

P121-1 - See Thru

P131-1 - Pier

P121RC-1 - Corner Unit

Note: These units are

non-load bearing.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

FACING & FINISHING REQUIREMENTS

This fireplace is supplied with a 3" metal extension trim above the fireplace. The extension trim may be replaced if the framing is faced with a non-

combustible material placed flush with the front and side face of the unit and extending from the top of the unit. (ie. tile, slate, etc.)

VENTING

INTRODUCTION

UNIT ASSEMBLY

PRIOR TO

INSTALLATION

The P121-1/P121LC-1/P121RC-1/P131-1 uses

the "balanced flue" technology Co Axial

system. The inner liner vents products of com-

bustion to the outside while the outer liner

draws outside combustion air into the combus-

tionchambertherebyeliminatingtheneedtouse

heated room air for combustion and losing

warm room air up the chimney.

The 4 Top Standoffs must be correctly positioned and attached to the top before unit is slipped

into position.

TopStandoffAssembly

The top standoffs are shipped in a flat position and must be folded into shape and attached.

1) Remove the standoffs from the fireplace

top.

Note: These flue pipes must not be con-

nected to any other appliance.

2) Take each standoff and bend into the

correct shape. Bend up at the bend lines

until the screw holes in the standoff and the

pre-punched screw holes on the fireplace

top line up.

The gas appliance and vent system must be

venteddirectlytotheoutsideofthebuilding, and

never be attached to a chimney serving a

separate solid fuel or gas burning appliance.

Each direct vent gas appliance must use it's

own separate vent system. Common vent sys-

tems are prohibited.

3) Attach the standoff securely to the top with

4 screws per standoff (on opposite cor-

ners).

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

EXTERIOR VENT TERMINATION LOCATIONS

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

VENTING ARRANGEMENT - HORIZONTAL TERMINATIONS

Regency Direct Vent System (Flex) Horizontal Terminations Only

These venting systems, in combination with the P121-1/P121LC-1/P121RC-1/P131-1 Direct Vent Gas Fireplace, have been tested and listed as

a direct vent heater system by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations

diagram on page 12.

Regency Direct Vent (Flex) System Termination Kit (Part# 946-513) includes all the parts needed to install the P121-1/P121LC-1/

P121RC-1/P131-1 with a maximum run of 2 feet.

1) 6-7/8" dia. flexible liner (2 ft. length)

2) 4" dia. flexible liner (2 ft. length)

3) spring spacers (3)

4) thimble (2)

5) AstroCap termination cap (1)

6) screws (12)

7) tube of Mill Pac (1)

8) plated screws (8)

9) screws #8 x 1-1/2" drill point, stainless steel (4)

Notes:

1) Liner sections should be continuous without any joints or seams.

2) Only Flex pipe purchased from Regency may be used for Flex installations.

3) Regency Direct Vent System (Flex) is only approved for horizontal terminations.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

SIMPSON DURA-VENT VENTING

Horizontal or Vertical Terminations

The Simpson Dura-Vent Direct Vent System offers a complete line of component parts for installation of both horizontal and vertical installations.

Many items are offered in decorative black, as well as galvanized finish. We recommend using the galvanized finish for installation with the P121-

1/P121LC-1/P121RC-1/P131-1.

The minimum components required for a

basic horizontal termination are:

vinyl siding standoff, to

create a level surface to

mount the vent terminal.

The Terminal must not be

recessedintosiding.Meas-

ure the wall thickness in-

cluding furring strips.

Simpson Duravent Adaptor

Horizontal Termination Cap

45^oElbow

Flue Adaptor

WallThimble

Length of pipe to suit wall thickness

(see chart)

If a Vinyl Siding Standoff is

required (it must be used

with vinyl siding), measure

to outside surface of wall

without siding and add 2

inches.

Wall thickness is measured from the back

standoffs to the inside mounting surface of

termination cap. For siding other than vinyl

furring strips may be used, instead of the

Flat Wall Installation

Wall Thickness

(inches)

Vent Length

Required (inches)

4" - 5-1/2"

7" - 8-1/2"

10" - 11-1/2"

9" - 14-1/2"

15" - 23-1/2"

12"

11" - 14-5/8" Adj. Pipe

17" - 24" Adj. Pipe

Simpson

Dura-Vent

Direct Vent GS

The Regency AstroCap^TMis certified for installations using FPI

venting systems as well as Simpson Dura-Vent® and Direct

Vent GS.

Regency^TM, and Regency AstroCap^TMare the proprietary trade-

marks of FPI Fireplace Products International Ltd.

Dura-Vent® and Direct Vent GS are registered and/or propri-

etary trademarks of Simpson Dura-Vent Co. Inc.

SIMPSON DURA-VENT VENTING COMPONENTS LIST

All Simpson Dura-Vent components are available directly from Regency.

Part # Description

902 48" Pipe Length - Galv.

902B 48" Pipe Length - Black

911B 11"-14 5/8" Adjustable Pipe Length -

Black

Part # Description

982 Snorkel - 14" Rise Termination Cap

981 Snorkel - 36" Rise Termination Cap

940 Wall Thimble - Support/Box

941 Cathedral/Ceiling - Support/Box

3951 Brass Trim for Wall Thimble/Ceiling Sup.

963 Firestop Spacer

943 Flashing 0/12-6/12

943S Flashing 7/12-12/12

953 StormCollar

950 Vinyl Siding Standoff

988 Wall Strap

971

Horiz.TerminationKit includes:

90^oblack elbow, wall thimble cover, horiz.

square termination cap, 24" black pipe, and 11"

-14" 5/8" adjustable black pipe

970

Basic Horiz. Termination. Kit includes:

90^oblack elbow, wall thimble cover,

horiz. square termination cap

917B 17"- 24" Adjustable Length - Black

945

45^OElbow - Galv.

945B 45^OElbow - Black

978

Vert. Termination Kit includes 0/12 -

6/12 pitch adjustable flashing, storm

collar, low profile term. cap

945G 45^OElbow - Swivel - Galv.

945BG 45^OElbow - Swivel - Black

990

90^OElbow - Galv.

908B 6" Pipe Length - Black

907B 9" Pipe Length - Black

990B 90^OElbow - Black

990G 90^OElbow - Swivel - Galv.

942 WallThimble

Parts not supplied by Dura-Vent

906

906B 12" Pipe Length - Black

904 24" Pipe Length - Galv.

904B 24" Pipe Length - Black

903 36" Pipe Length - Galv.

12" Pipe Length - Galv.

990BG 90^OElbow - Swivel - Black

946-506/P

510-994

640-530/P

946-205

Vent Guard (Optional)

Dura-Vent Flue Adaptor

Riser Vent Terminal

Vinyl Siding Shield for Riser

Vent Terminal

991

980

984

985

High Wind Termination Cap (Vertical)

Vertical Termination Cap

Horizontal Square Termination Cap

Horiz. Square High Wind Termination

Cap

903B 36" Pipe Length - Black

946-206

AstroCap Standoff

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS

SIMPSON DURA-VENT DIRECT VENT GS SYSTEM (Propane & Natural Gas)

The diagram below shows examples of horizontal termination arrangements using one, two, or three 90^oelbows (two 45^oelbows equal one 90^o

elbow).

Note:

1) A maximum of three 90^oelbows are permitted.

Simpson Dura-Vent

4" inner diameter

2) Minimum distance between elbows is 1 ft. (305mm).

6-5/8" outer diameter

•

Maintain clearances to combustibles as listed on page 9.

Horizontal vent must be supported every 3 feet.

Firestops are required at each floor level and whenever passing through a wall.

Must use optional flue adapter (Part# 510-994) when using Simpson Dura-Vent pipe.

A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes.

Horizontal Venting with One (1) 90^oElbow

Straight Out Horizontal Venting

Option

1' (305mm) Minimum

2' (610mm) Minimum

3' (914mm) Minimum

4' (1.22m) Minimum

5' (1.5m) Minimum

6' (1.86m) Minimum

3' (914mm) Maximum

6' (1.86m) Maximum

9' (2.7m) Maximum

12' (3.6m) Maximum

15' (4.5m) Maximum

17' (5.1m) Maximum

With the above options, maximum total pipe length if 37 feet with

minimumof6feettotalverticalandmaximum17feettotalhorizontal.

Please note minimum 1 foot between 90^oelbows is required.

Diagram 1

Diagram 2

Please note the minimum centerline

for basic install shown above.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Horizontal Venting with Two (2) 90^oElbows

Horizontal Venting with Three (3) 90^oElbows

Option

H + H1 + H2

Option

H + H1

2' (610mm) Min. 1' (305mm) Max. 3'(914mm)Max.

3' (914mm) Min. 3' (914mm) Max. 6' (1.86m) Max.

4' (1.22mm) Min. 5' (1.5m) Max.

1' (305mm) Minimum

2' (610mm) Minimum

3' (914mm) Minimum

4' (1.22m) Minimum

5' (1.5m) Minimum

6' (1.86m) Minimum

2' (610mm) Maximum

5' (1.5m) Maximum

8' (2.4m) Maximum

11' (3.35m) Maximum

14' (4.27m) Maximum

15' (4.5m) Maximum

9' (2.7m) Max.

5' (1.5m) Min. 7' (2.13m) Max. 12' (3.6m) Max.

With the above options, maximum total pipe length if 37 feet with

minimum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

With the above options, maximum total pipe length if 37 feet with

minimum of 6 feet total vertical and maximum 15 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

Diagram 5

Horizontal Venting with Three (3) 90^oElbows

Diagram 3

Option

V + V1

H + H1

2' (610mm) Minimum

3' (914mm) Minimum

4' (1.22m) Minimum

5' (1.5m) Minimum

3' (914mm) Maximum

6' (1.86m) Maximum

9' (2.7m) Maximum

12' (3.6m) Maximum

Horizontal Venting with Two (2) 90^oElbows

Option

H + H1

With the above options, maximum total pipe length if 37 feet with

minimum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

1' (305mm) Min. 1' (305mm) Max. 3'(914mm)Max.

2' (610mm) Min. 3' (0.91m) Max. 6' (1.86m) Max.

3' (914mm) Min. 5' (1.5m) Max.

5' (1.5m) Min. 8' (2.4m) Max.

9' (2.7m) Max.

12' (3.6m) Max.

With the above options, maximum total pipe length if 37 feet with

minimum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

Diagram 4

Diagram 6

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

VENTING ARRANGEMENTS - VERTICAL TERMINATIONS

SIMPSON DURA-VENT DIRECT VENT GS SYSTEM (Propane & Natural Gas)

•

Vent must be supported at offsets

Maintain clearances to combustibles as listed on page 9.

Firestops are required at each floor level and whenever passing through a wall.

Must use optional flue adapter when using Simpson Dura-Vent pipe (Part# 510-994).

The P121-1/P121LC-1/P121RC-1/P131-1 is approved for a maximum 35 ft. (10.7m) straight vertical, with Simpson Dura-Vent Direct Vent GS

vent systems for Propane and Natural Gas, as per diagram 7 below.

Straight Up Vertical Venting

Vertical Venting with One (1) 90^oElbow

Option

1' (305mm) Minimum

2' (610mm) Minimum

3' (914mm) Minimum

4' (1.22m) Minimum

2' (610mm) Maximum

4' (1.22m) Maximum

6' (1.86m) Maximum

8' (2.4m) Maximum

With the above options, maximum total pipe length if 37 feet with

minimum of 4 feet total vertical and maximum 8 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

Diagram 7

Diagram 8

IMPORTANT

When installing this unit vertically, the 45^oelbow when installed in

conjunction with the Simpson Dura-Vent Adaptor will pertrude past the

unit 1-1/2" (38mm) when measured from the rear standoffs.

Note:A1-1/4"(32mm)clearancefromtheelbowmustalsobemaintained.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Vertical Venting with Two (2) 90^oElbows

Option

H + H1

Option

1' (305mm) Minimum

2' (610mm) Minimum

3' (914mm) Minimum

4' (1.22m) Minimum

2' (610mm) Maximum

4' (1.22m) Maximum

6' (1.86m) Maximum

8' (2.4m) Maximum

1' (305mm) Minimum

2' (610mm) Minimum

3' (914mm) Minimum

4' (1.22m) Minimum

5' (1.5m) Minimum

6' (1.86m) Minimum

4' (1.22m) Maximum

6' (1.86m) Maximum

9' (2.7m) Maximum

12' (3.6m) Maximum

15' (4.5m) Maximum

17' (5.1m) Maximum

With the above options, maximum total pipe length if 37 feet with

minimum of 4 feet total vertical and maximum 8 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

With the above options, maximum total pipe length if 37 feet with

minimum of 6 feet total vertical and maximum 17 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

Diagram 9

Diagram 10

Vertical Venting with Three (3) 90^oElbows

Option

V + V1

H + H1

2' (610mm) Min. 1' (305mm) Max. 2' (610mm) Max.

3' (914mm) Min. 4' (1.22m) Max. 5' (1.5m) Max.

4' (1.22mm) Min. 6' (1.86m) Max. 8' (2.4m) Max.

5' (1.5m) Min.

8' (2.4m) Max.

12' (3.6m) Max.

With the above options, maximum total pipe length if 37 feet with

minimum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

Diagram 11

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Vertical Venting with Three (3) 90^oElbows

Option

V + V1

H + H1

2' (610mm) Minimum

3' (914mm) Minimum

4' (1.22m) Minimum

5' (1.5m) Minimum

3' (914mm) Maximum

6' (1.86m) Maximum

9' (2.7m) Maximum

12' (3.6m) Maximum

With the above options, maximum total pipe length if 37 feet with

minimum of 5 feet total vertical and maximum 12 feet total horizontal.

Please note minimum 1 foot between 90^oelbows is required.

Diagram 12

gram 1. Push the pipe sections com-

HORIZONTAL

INSTALLATIONS

pletely together, then twist-lock one

section clockwise approximately one-

quarter turn, until the two sections are

fullylocked. Thefemalelockinglugswill

not be visible from the outside, on the

Black Pipe or fittings. They may be

located by examining the inside of the

female ends.

Install the vent system according to the

manufacturer's instructions included

with the components.

1) Set the unit in its desired location. Check to

determine if wall studs or roof rafters are in

the way when the venting system is at-

tached. If this is the case, you may want to

adjust the location of the unit. Rough in the

gas.

Diagram 2

2) Direct Vent pipe and fittings are designed

with special twist-lock connections to con-

necttheventingsystemtotheapplianceflue

outlet. A twist-lock appliance adaptor is an

available option that must be used in con-

junction with the Simpson Dura-Vent Direct

Vent GS system.

Note:

a) Thehorizontalrunofventmustbelevel,

or have a 1/4 inch rise for every 1 foot

of run towards the termination. Never

allow the vent to run downward. This

could cause high temperatures and

may present the possibility of a fire.

Diagram 1

Note: Apply sealant "Mill-Pac" to inner

pipe and high temperature sili-

cone sealant to outer pipe on eve-

ry twist-lock joint.

3) Putabeadofsiliconeinsidetheoutersection

of the adapter and a bead of Mill Pac on the

inner collar. Slip the adapter over the exist-

ing inner and outer flue collar and fasten to

the outer collar only with the 3 supplied

screws (drilling pilot holes will make this

easier). Level the fireplace and fasten it to

the framing using nails or screws through

the nailing strips.

b) The location of the horizontal vent ter-

mination on an exterior wall must meet

alllocalandnationalbuildingcodes,and

must not be blocked or obstructed. For

External Vent Terminal Locations, see

diagram on page 12.

b) Horizontal runs of vent must be sup-

ported every three feet. Wall straps are

available for this purpose.

5) Mark the wall for a 10" x 10" square hole.

Thecenterofthesquareholeshouldlineup

with the centerline of the horizontal pipe.

Cutandframethe10inchsquareholeinthe

exterior wall where the vent will be termi-

nated. If the wall being penetrated is con-

structed of non-combustible material, i.e.

masonry block or concrete, a 7"(178mm)

dia. (7-1/2"(191mm) dia. for flex) hole is

acceptable.

6) The arrow on the vent cap should be

pointing up. Insure that the 1-1/2" clear-

ances to combustible materials are main-

tained (Diagram 3 on page 16). Install the

termination cap.

4) Assemble the desired combination of pipe

and elbows to the appliance adaptor and

twist-lock for a solid connection.

Note:

The four wood screws provided should be

replaced with appropriate fasteners for

stucco, brick, concrete, or other types of

sidings.

a) Twist-lockprocedure:Fourindentations,

located on the female ends of pipes and

fittings, are designed to slide straight

ontothemaleendsofadjacentpipesand

fittings, by orienting the four pipe inden-

tations so they match and slide in to the

four entry slots on the male ends, Dia-

Note: With Dura-Vent, the minimum height

is achieved by installing a 45^oelbow di-

rectly to the flue adaptor.

Note: If installing termination on a siding

covered wall, a vinyl siding stand-

off or furring strips must be used

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

4) Assemble the desired lengths of pipe and

elbows. Ensure that all pipes and elbow

connections are in the fully twist-locked

position and sealed.

VERTICAL

TERMINATION

1) Maintain the 1-1/4" clearances (air

spaces) to combustibles when

passing through ceilings, walls,

roofs, enclosures, attic rafter, or

other nearby combustible surfac-

es. Do not pack air spaces with

insulation. Check pages 17-19 for

the maximum vertical rise of the

venting system and the maximum

horizontal offset limitations.

5) Cut a hole in the roof centered on the small

drilled hole placed in the roof in Step 2. The

hole should be of sufficient size to meet the

minimumrequirementsforclearancetocom-

bustibles of 1-1/4". Slip the flashing under

the shingles (shingles should overlap half

the flashing) as per Diagram 4.

Diagram 3

2) Setthegasapplianceinits

desired location. Drop a

plumb bob down from the

ceiling to the position of

theapplianceflueexit,and

to ensure that the termination is

not recessed into the siding.

7) Before connecting the horizontal run of

vent pipe to the vent termination, slide the

WallThimble(Part#942)overtheventpipe.

Diagram 1

mark the location where

the vent will penetrate the

ceiling. Drill a small hole at his point. Next,

drop a plumb bob from the roof to the hole

previouslydrilledintheceiling,andmarkthe

spot where the vent will penetrate the roof.

Determine if ceiling joists, roof rafters or

other framing will obstruct

the venting system. You may

wish to relocate

theapplianceor

to offset, as

shown in Dia-

gram 2 to avoid

cutting load

bearing mem-

Diagram 4: The upper half of the flashing is

installed under the roofing material and not

nailed down until the chimney is installed.

This allows for small adjustments.

8) Slide the appliance and vent assembly to-

wards the wall carefully inserting the vent

pipe into the vent cap assembly. It is impor-

tant that the vent pipe extends into the vent

cap sufficient distance so as to result in a

minimum pipe overlap of 1-1/4 inches. Se-

cure the connection between the vent pipe

and the vent cap by attaching the two sheet

metal strips extending from the vent cap

assembly into the outer wall of the vent

pipe. Use the two sheet metal screws

provided to connect the strips to the pipe

section. See Diagram 4.

6) Continue to assemble pipe lengths.

Note: If an offset is necessary in the attic

to avoid obstructions, it is impor-

tant to support the vent pipe every

3 feet, to avoid excessive stress

on the elbows, and possible sep-

aration. Wall straps are available

for this purpose (Diagram 2).

bers.

9) Install wall thimble in the center of the 10"

square and attach with wood screws (Di-

agram 5).

Galvanized pipe is desirable above the roof-

line due to its higher corrosion resistance.

Continue to add pipe sections through the

flashing until the height of the vent cap meets

theminimumheightrequirementsspecifiedin

Diagram 5 or local codes. Note that for steep

Diagram 2

Note: Apply sealant "Mill-Pac" to inner

pipe and high temperature sili-

cone sealant to outer pipe on eve-

ry twist-lock joint.

Diagram 5

3) A Firestop spacer must be installed in the

floor or ceiling of every level. To install the

Firestop spacer in a flat ceiling or wall, cut

a 10 inch square hole. Frame the hole as

shown in Diagram 3 and install the firestop.

Roof Pitch

Minimum Vent Height

Feet

Meters

0.61

0.76

0.99

1.22

1.52

1.83

2.13

2.29

2.44

flat to 7/12

over 7/12 to 8/12

over 8/12 to 9/12

over 9/12 to 10/12

over 10/12 to 11/12

over 11/12 to 12/12

over 12/12 to 14/12

over 14/12 to 16/12

over 16/12 to 18/12

over 18/12 to 20/12

over 20/12 to 21/12

Diagram 4

2.5

3.25

7.5

Diagram 5

Diagram 3

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

roof pitches, the vertical height must be

increased. A poor draft, or down drafting

can result from high wind conditions near big

trees or adjoining roof lines, in these cases,

increasing the vent height may solve the

problem.

inside each other and can be adjusted for

2 x 4 or 2 x 6 walls. The liners must slip

over the collars a minimum of 1-3/8".

Note: To make the

installation more

aesthetically pleas-

ing, we recom-

mend framing out a

square to mount

the terminal to.

5) Slip the assembled liner and termination

assembly through the thimble making sure

the termination cap faces up (there are

markings on the cap that show which way

is up). This will position the termination cap

with proper down slope for draining water.

Fasten the cap to the outer wall with the 4

supplied screws.

7) Ensure vent is vertical and secure the base

of the flashing to the roof with roofing rails,

slide storm collar over the pipe section and

seal with a mastic.

8) Install the vertical termination cap by twist-

be used to ensure that the termi-

nation is not recessed into the

siding.

locking it.

6) Pull the centre 4"(100mm) liner and outer

6-7/8"(175mm) liner out enough to slip over

the flue collars of the fireplace. (You may

wish to cut the liner shorter to make it more

workable.) Do not bend liner more than 45^o.

Note: Any closets or storage spaces,

which the vent passes through

must be enclosed.

2) Level the fireplace and fasten it to the

framing using nails or screws through the

nailing strips.

7) Apply Mill Pac over the fireplace inner collar

and slip the 4"(100mm) liner down over it

and attach with 3 supplied screws.

OffsetChart

3) Assemble the vent assembly by applying

Mill Pac to the 4"(100mm) inner collar of the

terminationand slippingthe4"(100mm)liner

over it at least 1-3/8" (35mm). Fasten with

the 3 screws (drilling pilot holes will make

this easier). Apply Mill Pac or high temper-

aturesiliconetothe6-7/8"(175mm)flexpipe

and slip it over the 6-7/8" outer collar of the

vent terminal at least 1-3/8"(35mm) and

fasten with the 3 screws.

8) Do the same with the 6-7/8"(175mm) liner.

9) Apply a bead of silicone between the thim-

ble and termination and around the outer

edge of the terminal at the wall in order to

keep the water out.

IMPORTANT: Do not locate termination

hood where excessive snow or ice build-

up may occur. Be sure to check vent

terminationareaaftersnowfalls, andclear

to prevent accidental blockage of venting

system. When using snow blowers, make

sure snow is not directed towards vent

termination area.

NOTE: Horizontal sections must be sup-

ported at intervals not exceeding 3

feet (0.9 meter). (Flame picture and

performance will be affected by

sags in the liner).

4) Separatethe2halvesofthewallthimbleand

securely fasten the one with the tabs to the

outside wall making sure that the tabs are

on top and bottom. Fasten the other thimble

halftotheinsidewall.Thethimblehalvesslip

INSTALLATION

PROCEDURES

for Regency AstroCap^TMDirect

Vent System (Flex)

1) Locate the unit in the framing, rough in the

gas. Locate the centerline of the termina-

tion and mark wall accordingly. Cut a

10"(254mm) hole in the wall (inside dimen-

sion).

Note: A 1-1/2"(38mm) clearance around

the liner must be maintained ex-

cept that only a 1" (25mm) clear-

ance is needed at the termination

end. We recommend framing a

10"(254mm) x 10"(254mm) (inside

dimensions) hole to give struc-

tural rigidity for mounting the ter-

mination.

Note: If installing termination on a siding

covered wall, furring strips must

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

CONVERSION KIT FROM NATURAL GAS TO PROPANE MODEL #730-969

FOR P121-1/P121LC-1/P121RC-1/P131-1 USING SIT 820 NOVA GAS VALVE

THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER

IF IN DOUBT DO NOT DO THIS CONVERSION !!

Conversion Kit Contains:

5) Pull off the pilot

cap to expose the

pilot orifice.

Qty. Part # Description

910-018 SIT Conversion Kit-50%

Turndown LP

910-037 LP Injector (Pilot Orifice)

Burner Orifice #50

908-255 Decal "Converted to Propane"

908-529 5/32" Allen Key

918-032 Instruction Sheet

6) Unscrew the pilot orifice with the allen key

and replace with the LP pilot orifice in the kit

and replace pilot cap.

1) Removethelouversandtrimkit.Removethe

front door.

2) Remove the logs, embers.

3) Remove the grate by lifting straight up.

Remove the side brick panels (if installed).

The brick panel is very fragile - handle

with care.

7) Remove burner orifice with a 1/2" wrench

and discard. Use another wrench to hold

on to the elbow behind the orifice.

4) Remove the burner assembly by removing

the 4 Phillips head screws and then slide

the burner assembly away from the orifice

and lift out.

Burner Orifice

8) ReinstallnewburnerorificeLPstamped#50

and tighten.

9) Remove and discard the 3 pressure regu-

lator mounting screws (A), pressure regu-

lator tower (B) and diaphragm (C).

10) Insure that the rubber gasket (D) is properly

positioned and install the new HI/LO pres-

sure regulator assembly to the valve using

the new screws (E) supplied with the kit.

Tighten screws securely.

Diagram 1: Remove the left and right

screws and then slide the burner assembly

away from the orifice and lift out.

11) Reverse steps 4) to 1).

14) Check for gas leaks.

12) Attach clear label "This unit has been con-

verted to Propane" near or on the serial #

decal. Attach white label "This valve has

been converted from NG to LPG using SIT

conversion Kit Code 0.907.202" onto the

valve.

15) Check inlet and outlet pressures.

16) Check operation of flame control.

17) Check for proper flame appearance and

glow on logs.

13) Replace yellow "Natural Gas" label with red

"Propane" label

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

For USA installations follow local codes and/or The manifold pressure is controlled by a regu-

the current National Fuel Gas Code, ANSI lator built into the gas control, and should be

P121/P121LC/P121RC/P131-NG1

System Data

Z223.1.

checked at the pressure test point.

For 0 to 4500 feet altitude

Burner Inlet Orifice Sizes: #31

When using copper or flex connectors use only Note: To properly check gas pressure,

approved fittings. Always provide a union so

that gas lines can be easily disconnected for

servicing. Flare nuts for copper lines and flex

connectors are usually considered to meet this

requirement.

both inlet and manifold pressures

should be checked using the valve

pressure ports on the valve.

Max. Input Rating 40,000 Btu/h

Min. Input Rating 20,500 Btu/h

1) Makesurethevalveisinthe"OFF"position.

Supply Pressure min.5.0" w.c.

Important: Always check for gas leaks 2) Loosen the "IN" and/or "OUT" pressure

Manifold Pressure

with a soap and water solution or gas

leak detector. Do not use open flame for

leak testing.

tap(s), turning counterclockwise with a

1/8" wide flat screwdriver.

(High)

3.8"+/- 0.2"w.c.

Log Set: Ceramic fibre, 8 per set.

3) Attach manometer to "IN" and/or "OUT"

Vent System: Regency Astrocap^TM, Re-

gency Direct Vent System (Flex) and Simp-

son Dura-Vent Direct Vent System

pressure tap(s) using a 5/16" ID hose.

PILOT ADJUSTMENT

4) Light the pilot and turn the valve to "ON"

position.

5) The pressure check should be carried out

with the unit burning and the setting should

be within the limits specified on the safety

label.

P121/P121LC/P121RC/P131-LP1

System Data

Conversion Kit# 730-969

6) When finished reading manometer, turn off

the gas valve, disconnect the hose and

tighten the screw (clockwise) with a 1/8"

flat screwdriver. Note: Screw should be

snug, but do not over tighten.

For 0 to 4500 feet altitude

Burner Inlet Orifice Sizes: #50

Max. Input Rating 39,000 Btu/h

Min. Input Rating 20,600 Btu/h

Periodically check the pilot flames. Cor-

rect flame pattern has three strong blue

flames: 1 flowing around the thermopile,

1 around the thermocouple and 1 flowing

across the burner (it does not have to be

touching the burner).

Supply Pressure min.12.0" w.c.

S.I.T. VALVE DESCRIPTION

Manifold Pressure

1) Gas cock knob

2) Manual high/low adjustment

3) Pilot Adjustment

4) Thermocouple Connection - option

5) Outlet Pressure Tap

6) Inlet Pressure Tap

7) PilotOutlet

8) Main Gas Outlet

9) Alternative TC Connection

Point

(High)

11"+/- 0.2" w.c.

Log Set: Ceramic fibre, 8 per set.

Note: If you have an incorrect flame pat-

tern, contact your Regency dealer

for further instructions.

Vent System: Regency Astrocap^TM, Re-

gency Direct Vent System (Flex) and Simp-

son Dura-Vent Direct Vent System

Incorrect flame pattern will have small,

probably yellow flames, not coming into

proper contact with the rear burner or

thermopile or thermocouple.

HIGH ELEVATION

This unit is approved in Canada for altitude 0 to

4500 ft. (CAN1 2.17-M91).

GAS LINE

INSTALLATION

The gas line can be brought through either the

right,theleftside orthebottomoftheappliance.

The gas valve is situated on the bottom of the

unit.

GAS PIPE PRESSURE

TESTING

The gas line connection may be made of rigid

pipe, copper pipe or an approved flex connec-

tor. (If you are using rigid pipe, ensure that the

valve can be removed for servicing.) Since

somemunicipalitieshaveadditionallocalcodes

it is always best to consult with your local

authorities and the CAN/CGA B149 installation

code.

The appliance must be isolated from the gas

supply piping system by closing its individual

manual shut-off valve during any pressure

testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig. (3.45

kPa). Disconnect piping from valve at pres-

sures over 1/2 psig.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

1) Carefully remove the logs from the box and unwrap them. The logs

LOG INSTALLATION

are fragile, handle with care - do not force into position.

Read the instructions below carefully and refer to the diagrams.

If logs are broken do not use the unit until they are replaced.

Broken logs can interfere with the pilot operation.

2) Place Log 02-79 on the front right side of the burner. Ensure that the

notches on the far right side of the log fit into the grate posts. Push

back side of the left end of the log up against the tab on the burner.

The gas log kit (Part # 360-930) contains the following pieces:

a) 02-79 Front Right Log

b) 02-80 Front Left Log

c) 02-81 Middle Right Log

d) 02-82 Middle Left Log

902-326

902-327

902-328

902-329

902-154

Embers

02-79

Please note that there are 2 of each log. This

log set is mirrored front and back.

02-79

02-80

Push back side of the left end of the log up

against the tab on the burner.

Repeat step 2 on the opposite side of the burner.

02-79

02-82

02-81

The "02" reference numbers (i.e. 02-79) are

molded into the rear of each log.

The image below shows all of the logs in place.

3) Place Log 02-80 on the front left side of the burner. Position

the right end of the log in between the two tabs and the left

end of the log into the grate post.

02-81

02-79

02-82

02-80

Tab on Burner

Grate Post

02-80

02-82

02-79

02-81

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Repeat step 3 on the opposite side of the burner.

Repeat step 5 on the opposite side of the burner.

02-82

02-80

02-82

4) Embers should be placed in front of Log 02-79 and Log 02-80 and also

down the middle between the logs as shown in the image below.

6) Place Log 02-81 on the middle right side of the burner. Ensure that

the log fits over the 2nd grate post from the right.

02-81

Caution: Do NOT cover burner ports.

Grate Post

5) Place Log 02-82 on the middle left side of the burner. Rest the bottom

of the Log onto the second grate post from the left. Ensure that the log

fits into a pin that is on Log 02-79.

Repeat step 6 on the opposite side of the burner.

02-81

02-82

02-79

Place Log 02-82 onto pin.

Grate Post

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

GLASS DOOR

REMOVAL

FINISHING TRIM

LOUVERS & GRILLS

1) SlidetheSideFinishingTrimupintotheslot

in the top flange of the fireplace. Push tight

against the magnet at the base of the unit.

1) Attach the screws provided to the top left

and right corners.

1) Remove the 8 screws that secure the

glass door.

NOTE: Do not tighten the screw entirely,

ensure that some room is left to be able

to hang the grill or louver over the screw.

Slide Trim into

slot.

2) Hang the Top Louver or Grill onto the 2

screws in the top fireplace opening.

2) Pull the door slightly out on an angle and

then lift up and pull completely out.

Push trim tight

against magnet.

3) Attach the Bottom Louver or Grill to the

hingesonthebottomflangeofthefireplace.

2) Slide the Corner Finishing Trim up into the

slot in the top flange of the fireplace. Push

tight against the magnet at the base of the

unit.

P121-1 & P131-1 Corner Models

Slide Trim into

slot.

4) Attach the screws provided to the top and

bottom, left and right corners similar to step

5) Hang the top and bottom louver or grill onto

the screws in the top and bottom, left and

right sides of the fireplace opening.

3) P131 & P121LC/P121RC Corner Model:

Remove the 6 screws that secure the

glass door and repeat step 2.

Push trim tight

against magnet.

The Top and Bottom Side Louver or Grill is

installed the same way.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Option 1:

Option 3:

Option 2:

REMOTE CONTROL

WALL THERMOSTAT

WALL SWITCH

Can be used with Option 2 or 3

but not both.

Can be used with Option 1 or 3

but not both.

Can be used with Option 1 or 2

but not both.

Use the Regency Remote Control Kit approved

for this unit. Use of other systems may void your

warranty.

1) Run the supplied 15' of wire through the

back gas inlet opening. Be careful not to

damage wire.

A wall thermostat may be installed if desired,

connect the wires as per the wiring diagram.

Use the table below to determine the maximum

wire length.

The remote control kit comes with a hand held

transmitter, a receiver and a wall mounting

plate.

Note: We recommend a maximum of 15'

of wire but if you wish to go with a

longer run, use the Thermostat

Wire Table.

Note: Preferable if the thermostat is in-

stalled on an interior wall.

1) Choose a convenient location on the wall to

install the receiver and the receptacle box

(protection from extreme heat is very im-

portant). Run wires from the fireplace to

that location. Use the Thermostat Wire Ta-

ble.

Regencyoffersanoptionalprogrammablether-

mostat but any 250-750 millivolt rated non-

anticipator type thermostat that is CSA, ULC or

UL approved may be used.

2) Connect the wire to the supplied wall switch

and install into the receptacle box.

CAUTION

Do not connect millivolt

wall switch wire to a 120V wire.

CAUTION

2) Connect the two wires to the gas valve.

Do not connect millivolt

wall thermostat wires

to a 120V wire.

See diagram below.

Thermostat Wire Table

Recommended Maximum Lead Length

(Two-Wire) When Using Wall

CAUTION

Thermostat (CP-2 System)

Do not connect millivolt remote

control wires to a 120V wire.

Wire Size

Max. Length

14 GA.

16 GA.

18 GA.

20 GA.

22 GA.

50 Ft.

32 Ft.

20 Ft.

12 Ft.

9 Ft.

3) Install 3 AAA alkaline batteries in transmitter

and 4 AA alkaline batteries in the receiver.

Install the receiver and its cover in the wall.

Switch the remote receiver to "remote"

mode. The remote control is now ready for

operation.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

WIRING DIAGRAM

No electrical power supply is required for the

gas control to operate. 120 Volt AC power is

needed for the fan switch and blower. The fan

can be hard wired if desired. A terminal block

is provided on the left hand side of the unit. A

three wire power cord can also be used and

plugged into a suitable receptacle.

(Do not cut the ground terminal off under

any circumstances.)

Caution: Ensure that the wires do

not touch any hot surfaces and are

away from sharp edges.

CAUTION:

Label all wires

prior to disconnection when

servicing controls. Wiring er-

rors can cause improper and

dangerous operation.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

CAUTION: Carbon will be produced if air

shutter is closed too much.

6) Rotate the flame height regulator to adjust

OPERATING

the flame height higher or lower.

INSTRUCTIONS

Note: Any damage due to carboning re-

sulting from improperly setting

the aeration controls is NOT cov-

ered under warranty.

1) Read and understand these instructions

SHUTDOWN

PROCEDURE

before operating this appliance.

2) Check to see that all wiring is correct and

1) Use the wall switch, thermostat or remote

enclosed to prevent possible shock.

control to turn off the main burner.

3) Check to ensure there are no gas leaks.

2) Turn the main gas control clockwise to the

"OFF" position to turn off the pilot.

4) Make sure the glass in the door frame is

properly positioned. Never operate the ap-

pliance with the glass removed.

FIRST FIRE

5) Verify that the venting and cap are unob-

Adjustment Wire - Pull down to open or

push up to close aeration cap.

structed.

DO NOT BURN THE APPLIANCE

WITHOUT THE GLASS FRONT IN

PLACE.

6) Ensure that the brick panels are installed.

Closed - Tall yellow

Open - Short Blue

7) Verify log placement. If the pilot cannot be

seen when lighting the unit, the logs have

been incorrectly positioned.

The first fire in your stove is part of the paint

curing process. To ensure that the paint is

properly cured, it is recommended that you burn

your fireplace for at least four (4) hours the first

time before you use it with the fan on.

Note: Aeration Adjustment should only

be performed by an authorized

Regency Installer at the time of

installation or service.

8) The unit should never be turned off, and on

again without a minimum of a 60 second

wait.

When first operated, the unit will release an

odour caused by the curing of the paint, the

burning off of any oils remaining from manufac-

turing. Smoke detectors in the house may go off

at this time. Open a few windows to ventilate the

room for a couple of hours.

NORMAL OPERATING

SOUNDS OF GAS

APPLIANCES

Note: When the glass is cold and the

appliance is lit, it may cause con-

densation and fog the glass. This

condensation is normal and will

disappear in a few minutes as the

glass heats up.

It is possible that you will hear some sounds

from your gas appliance. This is perfectly nor-

mal due to the fact that there are various gauges

and types of steel used within your appliance.

Listed below are some examples. All are nor-

mal operating sounds and should not be

considered as defects in your appliance.

LIGHTING

PROCEDURE

IMPORTANT Gas cock knob cannot be

turned from "PILOT" to "OFF" unless it is

partially depressed.

During the first few fires, a white film

may develop on the glass front as part of

the curing process. The glass should be

cleaned after the unit has cooled down

or the film will bake on and become very

difficult to remove. Use a non-abrasive

cleaner and DO NOT ATTEMPT TO CLEAN

THE GLASS WHILE IT IS HOT.

Blower:

Regency gas appliances use high tech blowers

to push heated air farther into the room. It is not

unusual for the fan to make a "whirring" sound

when ON. This sound will increase or decrease

in volume depending on the speed setting of

your fan speed control.

1) Turn burner OFF using "ON/OFF" switch.

2) Turn gas control knob so indicator points to

"OFF" position and allow 5 minutes for any

gas in the combustion chamber to escape.

Burner Tray:

3) Turn gas control knob counterclockwise

so indicator points to the "PILOT" position.

Depress the gas control knob fully. De-

press the igniter button several times until

the pilot lights. After approximately one

minute, release the gas control knob. The

pilot flame should continue to burn. If the

pilot does not remain lit, repeat operation

allowing a longer period before releasing

gas control knob.

The burner tray is positioned directly under the

burner tube(s) and logs and is made of a

different gauge material from the rest of the

firebox and body. Therefore, the varying thick-

nesses of steel will expand and contract at

slightly different rates which can cause "tick-

ing" and "cracking" sounds. You should also be

aware that as there are temperature changes

within the unit these sounds will likely re-occur.

Again, this is normal for steel fireboxes.

AERATION

ADJUSTMENT

The air shutter can be adjusted by moving the

adjusting wire up or down. The wire is ac-

cessed through the bottom louver opening.

Open the air shutter for a blue flame or close for

a yellower flame. The burner aeration is factory

setbutmayneedadjustingduetoeitherthelocal

gas supply or altitude.

4) When the pilot stays lit, turn the gas knob

further counterclockwise to the "ON" po-

sition.

Blower Thermodisc:

When this thermally activated switch turns ON

it will create a small "clicking" sound. This is the

switch contacts closing and is normal.

Minimum Air Shutter Opening:

5) Use the wall switch, thermostat or remote

3/16"

3/8"

Natural Gas

Propane

control to turn on the unit.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING INSTRUCTIONS

Unit Body/Firebox:

Pilot Flame:

While the pilot flame is on it can make a very

slight "whisper" sound.

MAINTENANCE

INSTRUCTIONS

Different types and thicknesses of steel will

expand and contract at different rates resulting

in some "cracking" and "ticking" sounds will be

heard throughout the cycling process.

Gas Control Valve:

1) Always turn off the gas valve before

cleaning. For relighting, refer to lighting

instructions. Keep the burner and control

compartment clean by brushing and vacu-

uming at least once a year. When cleaning

the logs, use a soft clean paint brush as the

logs are fragile and easily damaged.

As the gas control valve turns ON and OFF, a

dullclickingsoundmaybeaudible,thisisnormal

operation of a gas regulator or valve.

Copy of the Lighting Plate Instructions

FOR YOUR SAFETY READ BEFORE LIGHTING

2) Cleanapplianceanddoorwithadampcloth

(never when unit is hot). Never use an

abrasive cleaner. The glass should be

cleaned with a gas fireplace glass cleaner.

The glass should be cleaned when it

starts looking cloudy.

This appliance must be installed in accordance with local codes, if any; if not, follow

thecurrentCAN1-B149/ANSIZ223.1(Australia:AG601,NewZealand:NZS5261)

WARNING: If you do not follow these instructions exactly, a fire or

explosion may result causing property damage, personal injury or loss

oflife.Improperinstallation,adjustment,alteration,serviceormaintenance

can cause injury or property damage. Refer to the owner’s information

manual provided with this appliance. For assistance or additional

information consult a qualified installer, service agency or gas supplier.

3) The heater is finished in a heat resistant

paint and should only be refinished with

heat resistant paint. Regency uses Stove-

Bright Paint - Metallic Black #6309.

A)This appliance has a pilot which C)Use only your hand to push in or turn

must be lighted by hand. When

lighting the pilot, follow these

instructions exactly.

the gas control knob. Never use tools.

If the knob will not push in or turn by

hand, don’ttrytorepairit, callaqualified

service technician. Force or attempted

repair may result in a fire or explosion.

4) Make a periodic check of burner for proper

position and condition. Visually check the

flame of the burner periodically, making

sure the flames are steady; not lifting or

floating. Ifthereisaproblem, callaqualified

service person.

B)BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the floor because some D) Do not use this appliance if any part has

gas is heavier than air and will settle

on the floor.

been under water. Immediately call a

qualifiedservicetechniciantoinspectthe

appliance and to replace any part of the

controlsystemandanygascontrolwhich

has been under water.

WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance

- Do not touch any electric switch, do

not use any phone in your building

5) The appliance and venting system must be

inspected before use, and at least annual-

ly, by a qualified field service person, to

ensure that the flow of combustion and

ventilation air is not obstructed.

This appliance needs fresh air for safe

- Immediately call your gas supplier operationandmustbeinstalledsothereare

from a neighbours phone. Follow the provisions for adequate combustion and

gassupplier’sinstructions.

- Ifyoucannotreachyourgassupplier,

call the fire department.

ventilation air.

Note: Never operate the appliance with-

out the glass properly secured in

place.

CAUTION:Hotwhileinoperation.Donottouch.SevereBurnsmayresult.Due

tohighsurfacetemperatureskeepchildren,clothingandfurniture,gasoline

and other liquids having fammable vapors away. Keep burner and control

compartment clean. See installation and operating instructions

accompanyingappliance.

6) Do not use this appliance if any part has

been under water. Immediately call a qual-

ified service technician to inspect the ap-

pliance and to replace nay part of the

control system and any gas control which

has been under water.

LIGHTING INSTRUCTIONS

STOP! Read the safety information 4) Push in control knob all the way and

above on this label.

1) Push in gas control knob slightly and

turn clockwise

hold in. Continually push and release

the black button on spark igniter until

pilot lights. Continue to hold the

control knob in for about 1/2 minute

after the pilot is lit. Release knob and

it will pop back up. Pilot should remain

lit. If it goes out, repeat steps 1) to 4).

If knob does not pop up when released,

stop and immediately call your service

technicianorgassupplier.Ifthepilotwill

notstaylitafterseveraltries,turnthegas

control knob to “OFF” and call your

service technician or gas supplier.

to “OFF”. Knob

cannotbeturnedfrom“PILOT”to“OFF”

unless knob is pushed in slightly. Do

notforce.

2) Wait five (5) minutes to clear out any

gas. IfyouthensmellgasSTOP!follow

“B” in the safety information above on

this label. If you don’t smell gas, go to

the next step.

7) In the event this appliance has been serv-

iced check that the vent-air system has

been properly resealed & reinstalled in

accordance with the manufacturer's in-

structions.

8) Verify operation after servicing.

3) Turn knob on gas control counter-

clockwise

to“PILOT”.

PILOT BURNER

VEILLEUSE

5) Turn gas control knob

OFF

General Vent Maintenance

counterclock-wise

to “ON”.

THERMOPILE

Conduct an inspection of the venting system

semi-annually.Recommendedareastoinspect

as follows:

6) Use rocker switch to op-

erate main burner.

ELEMENT

THERMO-

ELECTRIQUE

TO TURN OFF GAS APPLIANCE

1) Check the Venting System for corrosion in

areas that are exposed to the elements.

These will appear as rust spots or streaks,

and in extreme cases, holes. These com-

ponents should be replaced immediately.

2) Turn off all electric power to the

appliance if service is to be performed.

1) Push in the gas control knob slightly and

turn clockwise to “OFF”. Do not force.

You may shut off the pilot during prolonged non use periods to conserve fuel.

908-017a

DO NOT REMOVE THIS INSTRUCTION PLATE

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

2) Remove the Cap, and shine a flashlight

down the Vent. Remove any bird nests, or

other foreign material.

GLASS GASKET

REMOVING VALVE

If the glass gasket requires replacement use

a tadpole glass gasket (Part # 936-155).

1) Shut off the gas supply.

3) Check for evidences of excessive con-

densation, such as water droplets forming

intheinnerliner,andsubsequentlydripping

out the joints, Continuous condensation

can cause corrosion of caps, pipe, and

fittings. It may be caused by having exces-

sive lateral runs, too many elbows, and

exterior portions of the system being ex-

posed to cold weather.

2) Removethelouversandtrimkit.Removethe

front door.

3) Remove the logs, embers.

DOOR GLASS

4) Remove the grate by lifting straight up.

Your Regency fireplace is supplied with high

temperature 5mm-Tempered glass & 5mm-Ce-

ramic glass. If your glass requires cleaning, we

recommend using an approved glass cleaner

available at all authorized dealers. Do not use

abrasive materials.

4) Inspect joints, to verify that no pipe sections

or fittings have been disturbed, and conse-

quently loosened. Also check mechanical

supports such as Wall Straps, or plumbers'

tape for rigidity.

CAUTION&WARNINGS:

* Do not clean when the glass is hot.

* Theuseofsubstituteglasswillvoidallproduct

warranties.

* Care must be taken to avoid breakage of the

glass.

* Do not strike or abuse the glass.

* Do not operate this fireplace without the glass

front or with a cracked or broken glass front.

* Wear gloves when removing damaged or

broken glass.

* Replacement of the glass panels should be

done by a licensed or qualified service per

son.

LOG REPLACEMENT

5) Remove the side brick clip in the top of the

firebox and then slide the Side Brick Panel

out. The brick panels are very fragile

- handle with care.

Theunitshouldneverbeusedwithbrokenlogs.

Turn off the gas valve and allow the unit to cool

before opening door and carefully remove the

logs. (The pilot light generates enough heat to

burn someone.) If for any reason a log should

need replacement, you must use the proper

replacement log. The position of these logs

must be as shown in the diagrams under Log

Installation.

GLASSREPLACEMENT

Note: Improper positioning of logs may

create carbon build-up and will

severely alter the unit's perform-

ance which is not covered under

warranty.

In the event that you break your glass by impact,

purchase your replacement from an authorized

Regency dealer only. Replacement glass is

shipped already installed into the door frame.

Reinstall as per Glass Door Installation on page

22.

THERMOPILE/

THERMOCOUPLE

REPLACEMENTPARTS:

6) Remove the burner by removing the 4

screws.

Front Door - Tempered (Part# 360-528)

Side Door - Tempered (Part# 360-529)

Front Door - Ceramic (Part# 360-538)

Side Door - Ceramic (Part# 360-539)

1) OpentheBottomLouversorGrills.Remove

the Top Louver or Grill.

2) Remove the Trim Kit, Glass Door, Log Set,

Grate and Burner Assembly (see page 26).

3) Disconnect thermocouple by loosening nut

from the valve with a 9mm wrench. Discon-

nect thermopile by loosening 2 screws

marked TP on the valve.

GOLD-PLATED

ACCESSORIES

The 24 carat gold-plated finish requires little

maintenance, and need only be cleaned with a 7) Slide the burner assembly away from the

damp cloth. DO NOT use abrasive materials or

chemical cleaners, as they may harm the finish

and void the warranty. Clean any finger-

prints off before turning the unit on.

4) Remove 2 screws from the pilot assembly

and pull up far enough to be able to loosen

thethermocoupleorthermopilewitha7/16"

wrench. NOTE: the pilot line is very fragile,

use caution when pulling it up.

orifice and lift out.

5) Drop the thermocouple or thermopile down

through the extrusion and pull it out of the

unit.

6) Reinstall the new ones in reverse order.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

8) Remove the Side Base Brick Panels and 13) Undo the pilot tube from the valve with a

INSTALLING VALVE

finally the Long Base Brick Panels.

7/16" wrench.

14) Undo the quick drop out thermocouple nut

on the valve with a 9mm (metric) wrench.

1) Attach the valve to the valve bracket with

the 6 (m5x8 metric) screws provided.

15) Remove the Piezo igniter wire and push

button assembly.

2) Reconnect the "gas out" flare fitting with an

11/16" wrench.

16) Undo the "gas out" flare nut with a 13/16"

wrench.

3) Reconnect the "gas out" flare nut with a 13/

16" wrench.

17) Undo the "gas out" flare fitting with an

11/16" wrench.

4) Install piezo ignitor push button assembly

and reconnect wire.

Remove Left & Right Side Base

Brick Panels

18) Removethe6Phillipsheadscrewsfromthe

sides of the valve bracket and remove

valve.

5) Reconnectthequickdropoutthermocouple

nut with a 9mm wrench.

6) Reconnect the pilot tube nut with a 7/16"

Hint: If you are using black pipe, ensure

that there is a union by the valve,

otherwise removal will be almost

impossible.

wrench.

7) Scrape off the old gasket from the floor of

the firebox and from the valve tray assem-

bly.

8) Install a new gasket and reinstall the valve

tray assembly.

Note: Failure to install a new gasket may

severely affect the appliance perform-

ance.

Remove the 2 Long Base Brick Panels

9) Reinstall the 16 hold down screws.

9) Disconnect the inlet gas line.

10) Hook up the 2 TP and 2 TH wires to the

appropriate connections on the valve.

10) Disconnect the 2 TP wires and the 2 TH

wires from the valve.

11) Reinstall the Burner Assembly.

11) Remove the 16 Phillips head screws secur-

ing the valve tray.

13) Hookupthegaslineandcheckforgasleaks

with a soap and water solution or a gas leak

detector. (Do not use open flame for leak

testing.)

14) Fire up the unit temporarily

15) Check the manifold pressure.

16) Reinstallthelogs, grate andbrickpanelsas

needed.

17) Reinstall the glass doors.

18) Fire up the unit again and check for proper

flame appearance.

12) Lift the entire assembly out.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

FAN REPLACEMENT

1) Shut off power.

6) Replace fan.

2) Remove top louvers.

7) Repeat for opposite side/corner.

3) Unplug power wires.

8) Reverse steps 1 - 5 for installation.

4) Remove 4 screws securing fan to mounting bracket.

9) To remove the thermodisc, located at the back center of the unit, slide

the thermodisc/cover assembly away from the bracket clip on the under

side of the firebox. Reverse for installation. Ensure that no wires will touch

hot surfaces.

5) Remove 2 connector wires.

Connector wires

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

P121-1 (SEE THRU) MAIN ASSEMBLY

Part #

Description

Part #

Description

Part #

Description

135) 360-069 Heat Shield - Side

360-926 LouverFront-Black/Brass(set)

1) 360-528 Door Assy Front - Tempered

360-538 Door Assy Front - Ceramic

(Optional)

181) *

Extension Trim - See Thru

146) 360-033 Left Side Door Trim

360-034 Right Side Door Trim

150) 360-123 Magnet Bracket - Front

151) 904-258 Magnet

204) 360-940 Dec. Grill Front - Black (set)

2) 360-529 Door Assy Side - Tempered

360-539 Door Assy Side - Ceramic

(Optional)

205) 948-216 Regency Logo Plate

206) 910-171 Fan Axial 115V

168) 360-068 Door Cover Assembly - Side

207) 910-142 Thermodisc

918-107a Manual

9) 360-046 Nailing Strip - Top - Front

10) 360-047 Nailing Strip - Top - Side

11) 430-001 Standoff - Top

171) 360-920 Louver Front - Black (set)

360-922 Louver Front - Black/Gold (set)

360-924 Louver Front - Black/Steel (set)

17) 360-086 Gasket - Relief Door

*Not available as a replacement part.

24) *

Relief Door Assembly

32) 902-296 Brick Panel - Base - Front

33) 902-297 Brick Panel - Base - Side

34) 902-298 Brick Panel - Side

98) 910-366 Switch Cover Plate

99) 910-363 Wall Switch

100) 910-367 Switch Receptacle Plastic Box

910-882 Wire - Valve to Burner Switch

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

P131-1 (PIER) MAIN ASSEMBLY

Part #

Description

Part #

Description

Part #

Description

141) 360-031 ColumnFinishingTrim

146) 360-035 FinishingTrim

1) 360-528 Door Assy Front - Tempered

360-946 Door Assy Front - Ceramic

(Optional)

181) *

Extension Trim - Pier

204) 360-940 Dec. Grill Front - Black (set)

206) 910-171 Fan Axial 115V

149) 360-122 Magnet Bracket - Corner

150) 360-123 Magnet Bracket - Front

151) 904-258 Magnet

2) 360-529 Door Assy Side - Tempered

360-948 Door Assy Side- Ceramic

(Optional)

224) 360-942 Dec. Grill Side - Black (set)

225) 948-216 Regency Logo Plate

226) 910-412 Thermodisc

171) 360-920 Louver Front - Black (set)

360-922 Louver Front - Black/Gold (set)

360-924 Louver Front - Black/Steel (set)

360-926 Louver Front - Black/Brass (set)

9) 360-046 Nailing Strip - Top - Front

10) 360-047 Nailing Strip - Top - Side

11) 430-001 Standoff - Top

918-107a Manual

*Not available as a replacement part.

17) 360-086 Gasket - Relief Door

173) 360-932 Louver Side - Black (set)

360-934 Louver Side - Black/Gold (set)

360-936 Louver Side - Black/Steel (set)

360-938 Louver Side - Black/Brass (set)

24) *

Relief Door Assembly

32) 902-296 Brick Panel - Base - Side

33) 902-297 Brick Panel - Base - Front

34) 902-298 Brick Panel - Side

98) 910-366 Switch Cover Plate

99) 910-363 Wall Switch

100) 910-367 Switch Receptacle Plastic Box

910-882 Wire - Valve to Burner Switch

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

P121RC-1 (RIGHT CORNER) MAIN ASSEMBLY

Part #

Description

Part #

Description

Part #

Description

173) 360-932 Louver Side - Black (set)

360-934 Louver Side - Black/Gold (set)

360-936 Louver Side - Black/Steel (set)

360-938 Louver Side - Black/Brass (set)

35) 902-300 Brick Panel - Front

1) 360-528 Door Assy Front - Tempered

360-538 Door Assy Front - Ceramic

(Optional)

98) 910-366 Switch Cover Plate

99) 910-363 Wall Switch

100) 910-367 Switch Receptacle Plastic Box

910-882 Wire - Valve to Burner Switch

2) 360-529 Door Assy Side - Tempered

360-539 Door Assy Side - Ceramic

(Optional)

181) *

Extension Trim

204) 360-940 Dec. Grill Front - Black (set)

206) 910-171 Fan Axial 115V

224) 360-942 Dec. Grill Side - Black (set)

138) 360-063 Heat Shield - Front

141) 360-031 ColumnFinishingTrim

9) 360-046 Nailing Strip - Top - Front

10) 360-047 Nailing Strip - Top - Side

11) 430-001 Standoff - Top

780-013 Standoff - Rear

17) 360-086 Gasket - Relief Door

146) 360-035 Finishing Trim - Left Side

225) 948-216 Regency Logo Plate

226) 910-142 Thermodisc

149) 360-122 Magnet Bracket - Corner

150) 360-123 Magnet Bracket - Front

151) 904-258 Magnet

24) *

Relief Door Assembly

918-107a Manual

158) 360-060 Door Cover Assembly-Front

32) 902-296 Brick Panel - Base - Side

33) 902-297 Brick Panel - Base - Front

34) 902-298 Brick Panel - Side

*Not available as a replacement part.

171) 360-920 Louver Front - Black (set)

360-922 Louver Front - Black/Gold (set)

360-924 Louver Front - Black/Steel (set)

360-926 Louver Front - Black/Brass (set)

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

P121LC-1 (LEFT CORNER) MAIN ASSEMBLY

Part #

Description

Part #

Description

Part #

Description

173) 360-932 Louver Side - Black (set)

360-934 Louver Side - Black/Gold (set)

360-936 Louver Side - Black/Steel (set)

360-938 Louver Side - Black/Brass (set)

98) 910-366 Switch Cover Plate

99) 910-363 Wall Switch

100) 910-367 Switch Receptacle Plastic Box

910-882 Wire - Valve to Burner Switch

1) 360-528 Door Assy Front - Tempered

360-538 Door Assy Front - Ceramic

(Optional)

2) 360-529 Door Assy Side - Tempered

360-539 Door Assy Side - Ceramic

(Optional)

204) 360-940 Dec. Grill Front - Black (set)

206) 910-171 Fan Axial 115V

224) 360-942 Dec. Grill Side - Black (set)

138) 360-069 Heat Shield - Front

141) 360-031 ColumnFinishingTrim

146) 360-035 FinishingTrim

9) 360-046 Nailing Strip - Top - Front

10) 360-047 Nailing Strip - Top - Side

11) 430-001 Standoff - Top

225) 948-216 Regency Logo Plate

226) 910-142 Thermodisc

149) 360-122 Magnet Bracket - Corner

150) 360-123 Magnet Bracket - Front

151) 904-258 Magnet

918-107a Manual

17) 360-086 Gasket - Relief Door

24) *

Relief Door Assembly

*Not available as a replacement part.

158) 360-062 Door Cover Assembly-Front

32) 902-296 Brick Panel - Base - Side

33) 902-297 Brick Panel - Base - Front

34) 902-298 Brick Panel - Side

171) 360-920 Louver Front - Black (set)

360-922 Louver Front - Black/Gold (set)

360-924 Louver Front - Black/Steel (set)

360-926 Louver Front - Black/Brass (set)

35) 902-300 Brick Panel - Front

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS LIST

P121/P121LC/P121RC/P131-1 BURNER ASSEMBLY & LOG SET

Part #

Description

360-930

41) 904-326

42) 904-327

43) 904-328

44) 904-329

Log Set

Front Right Log

Front Left Log

Middle Left Log

Middle Right Log

360-574/P

56) 360-378/P

Valve Assembly

Valve S.I.T. - NG

57) 360-090

58) *

Gasket - Valve Tray

Valve Tray

66) 910-038

Pilot Assembly - NG

67) *

PilotHolder

68) W840470

69) 910-190

Pilot Assembly Gasket

Piezo Ignitor and Nut

79) 360-525

82) 360-027

904-690

Burner Assembly

Grate Assembly

Orifice #31 - NG

Orifice Gasket

936-170

*Not available as a replacement part.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY

Regency Fireplace Products, are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance

Teamcarefullyinspectseachunitthoroughlybeforeitleavesourdoor. RegencyIndustriesLtd.ispleasedtoextendthislimited

lifetime warranty to the original purchaser of a Regency Product.

The Warranty: Lifetime

Covered under the agreement are the following components: Combustion chamber, heat exchanger, burner tubes, logs, embers,

glass (thermal breakage) and all gold plating (against defective manufacture).

The above will be covered for parts and labour for the first five years and parts only thereafter. Electrical components such as blowers,

fan motor, switches, wiring, thermodiscs, remote control, thermopiles, thermocouples, pilot assemblies, and gas valves are

covered for one year from the date of purchase.

Conditions:

All installations must be performed by a qualified gas fitter and installed according to all applicable local and national codes. Also,

all service work must be carried out by a qualified gas service person who is recommended by the selling dealer. It is the

responsibility of the installer to ensure that the appliance is firing as per rating plate. Any part or parts of this unit which in our

judgement show evidence of such defect will be repaired or replaced at Regency's option, through an accredited distributor or agent

provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.

Exclusions:

This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim. It does not cover installation

and operational related problems such as over-firing, downdrafts or spillage caused by environmental conditions, nearby trees,

buildings, hilltops, mountains, inadequate venting or ventilation, excessive offsets, negative air pressures caused by insufficient

make up air, mechanical systems such as furnaces, fans, clothes dryers etc.

The warranty does not extend to any part or parts which show evidence of misuse or abuse, neglect, accident or lack of maintenance.

Products made by other manufacturers and used in conjunction with the operation of this appliance without authorization from

Regency, may nullify your warranty on this product.

Regency Industries Ltd., shall in no event be liable for any special, indirect consequential damages of any nature whatsoever which

are in excess of the original purchase price of the product. Any alteration to the unit which causes sooting or carboning that results

in damage to the exterior facia is not the responsibility of Regency Industries Ltd.

Note: Warranty is not transferable.

VentComponents:

The venting components are under warranty from Simpson Dura-Vent Inc.

General:

It is essential that all submitted claims provide all of the necessary information including purchase date, serial #, type of unit and

part or parts requested.

Regency P121-1/P121LC-1/P121RC-1/P131-1 Zero Clearance Direct Vent Gas Fireplace

Download from Www.Somanuals.com. All Manuals Search And Download.

Regency fireplace products are designed

withreliabilityandsimplicityinmind. In

addition, our internal QualityAssurance

Team carefully inspects each unit

thoroughly before it leaves our

door.

Fireplace Products International

Ltd. is pleased to extend this Lim-

ited Lifetime Warranty to the original

purchaser of a Regency Product.

See the inside back cover for details.

http://www.regency-fire.com

Installer:Pleasecompletethefollowinginformation

Dealer Name & Address:______________________________________________

__________________________________________________________________

Installer: ___________________________________________________________

Phone #: ___________________________________________________________

Date Installed: ______________________________________________________

Serial No.: _________________________________________________________

Regency and Panorama are trademarks of FPI Fireplace Products International Ltd.

Printed in Canada

Download from Www.Somanuals.com. All Manuals Search And Download.

Radio Shack Motorized Toy Car 60 4360 User Guide
RCA CD Player CDRW120 User Guide
RCA Stereo System ANT3901 User Guide
RedMax Gas Grill EDG2300R User Guide
Remington Chainsaw RM1632A User Guide
RIDGID Drill R82015 User Guide
Rotel Turntable RP 1000 User Guide
Samsung CRT Television TXK 3276 User Guide
Samsung Tablet GT P1000CWAXEU User Guide
Sennheiser Headphones 500371 User Guide