Extra Tall Wide Span Gate
MODEL NO: 1154
Owner’s Manual
11/19/2013_BL
READ ALL INSTRUCTIONS BEFORE ASSEMBLY
AND USE OF GATE.
KEEP INSTRUCTIONS FOR FUTURE USE.
...........................................................................
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306-9803, USA
Toll Free: 866-272-5274
Made in China
Download from Www.Somanuals.com. All Manuals Search And Download.
Check to make sure you have all of the parts shown:
B.
C.
A.
D.
A. Gate Frame
B. 4 Wall Cups
C. 4 Screws (requires a Phillips/crosshead screwdriver)
D. 4 Threaded Spindle Rods
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Extensions List
NOTE
12
8
6
4
Item NO.
MAX Size
29--52 inches
1154
NOTE: When installing any gate at its maximum width use Wall
Mounting Cups to ensure stability and safety.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling andInstalling Your Gate
**Note: IMPORTANT!! You will notice a slight gap between the gate door latch and the
frame. THIS IS NOT A DEFECT. Your gate is a pressure mounted gate and this gap will
disappear once you tighten your gate in its opening.
Step 1.
Locate the 4 threaded spindle rods. Rotate the adjustment wheels along the threading,
eliminating the gap between the adjustment wheel and the rubber foot.
Threaded Spindle Rod
Diagram A
Adjustment Wheel
Rubber Foot
Step 2.
Insert the 4 threaded spindle rods into the holes at each of the 4 corners of the gate as
shown in the Diagram
Diagram B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3.
Position the gate so that it is level and centered within your doorway or opening.
Rotate the adjustment wheels on the threaded spindle rods in the opposite direction
at in Step 1, expanding the gap between the rubber foot and the adjustment wheel.
Expand each of the 4 Threaded Spindle Rods until they make contact with the
doorway or opening. Do not fully tighten the Threaded Spindle Rods yet.
Diagram C1
Diagram C2
It may be necessary to hold the Threaded Spindle Rods or Rubber
Feet while rotating the Adjustment Wheels to ensure the entire
unit does not rotate.
HINT:
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Step4.
When you are satisfied with the general placement of your gate, fully tighten
the Threaded Spindle Rods attached to the lower corners of the gate by
further rotating the Adjustment Wheels.
Continue by tightening the upper Threaded Spindle Rods. As you tighten the
upper Threaded Spindle Rods, you will notice the gap between the Door
Frame and the Easy Open Latch begin to narrow.
In order for the gate to function properly, stop tightening the upper
Threaded Spindle Rods just before the inner wall of the Locking Latch and
the Gate Frame touch.
Easy Open Latch
Locking Latch
Gate Frame
Diagram D
There should be equal spacing among each of the 4 Threaded
Spindle Rods. Make the appropriate adjustment to ensure you
have installed your gate safely.
NOTE:
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning and Attaching the Wall Cups
Your gate is a pressure mounted gate. Therefore, it is not necessary to use the screw
attached Wall Cups in your door opening if you choose not to. However, IF YOUARE
USING THE GATE AT THE TOP OF STAIRS YOU MUST USE THE WALL CUPS. Using the
Wall Cups will affix your gate more firmly in the doorway or opening.
Step1.
After you have mounted your gate, and you are satisfied with its positioning, use a
pencil or other marking tool to draw a circle on the surface of your doorway or
opening around the perimeter of the 4 rubber feet.
Diagram E
Step2.
Next, completely remove the gate from the opening by loosening each of the 4
Threaded Spindle Rods and de-pressurizing the gate.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Step3.
With the gate fully removed, you can now use the circles you marked during Step 1
as guides for screwing in your 4 Wall Cups.
Center each of the Wall Cups within the guide circles and use the provided
self-tapping screws to fasten them in place via the hole through the center of each
Wall Cup.
Diagram F
Step4.
Reinstall your gate in the doorway or opening according to the instructions, using
the newly installed Wall Cups as anchoring points for the 4 Threaded Spindle Rods
Diagram G
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the Door Latch
Step1.
Pull the Spring Lock away from the Easy Open Latch while simultaneously
lifting the Lock Lever upwards. This will release the Locking Latch from the
Gate Frame and allow the door to push or pull open.
Spring Lock
Lock Lever
Diagram H
Step2.
To lock the door shut, close the door completely, then push down on the
Lock Lever to re-engage the Spring Lock
If your Easy Open Latch is not properly engaging with the
receiving component, ensure that your gate is level, mounted
HINT:
properly, and that you have not over-tightened the threaded
Spindle Rods.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Adding a Gate Extension
Step 1. Assemble the gate per the gate instructions.
Step 2. Choose the side of the gate to be extended and remove the top
and bottom Threaded Spindle Rods.
Step 3. Assemble the gate and extension as illustrated.
Step 4. Reposition the gate and fit in accordance with the gate fitting
instructions.
Removing Your Gate From The Wall
To remove your gate from the wall, rotate the Adjustment Wheels on
each of the 4 Threaded Spindle Rods to depressurize the gate from its
doorway or opening. Then, gently pull or push the gate free from its
doorway or opening.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care And Maintenance
Periodically check the gate for signs of damage, wear, or missing
components.
Do not use if any part is missing, worn or damaged.
Check the gate regularly to ensure all the hardware and mountings are
tightened.
Do not use abrasive cleaners or bleach.
Clean by sponging with warm water and a mild detergent.
90 Days Limited Warranty:
If, during the first 90 days after consumer purchase of the item, under
reasonable and non-commercial use and conditions of maintenance, it
fails while owned by the original purchaser because of the quality of
materials or workmanship of finish and assembly, Regalo International
LLC will replace or repair it at Regalo’s option. PROOF OF PURCHASE
REQUIRED.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts Available
In the event of any damage or breakage, the following replacement parts
are available for order by contacting Regalo Customer Service.
Wall Cups
(#14015)
1” Wall Mount Screws
Threaded Spindle Rods
with Adjustment Wheel
(#14016)
(#10001)
Bottom Plug Insert
(#14019)
Easy Open Latch
(#13037)
Top Plug Insert
(#14020)
Contact Regalo for questions and replacement parts.
For questions about the use of your gate, call our customer care line 866-272-5274.
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306-9803, USA
Made in China
Download from Www.Somanuals.com. All Manuals Search And Download.
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306-9803, USA
Toll Free: 866-272-5274
Made in China
11/19/2013_BL
Download from Www.Somanuals.com. All Manuals Search And Download.
|