®
Model No. RBTL15500
Serial No.
USER'S MANUAL
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through di-
rect assistance from our factory.
TO AVOID UNNECESSARY DE-
LAYS, PLEASE CALL DIRECT TO
OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our Customer Hot Line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Patent Pending
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
®
new products, prizes,
®
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
400 volts or less and a minimum surge dissi-
pation of 450 joules. The surge suppressor
must be electrically rated for 120 volts AC and
15 amps.
2. Use the treadmill only as described.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it. Do not
place the treadmill on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the treadmill.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
16. The heart rate monitor is not a medical de-
vice. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is in-
tended only as an exercise aid in determining
heart rate trends in general.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth-
ing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
10. When connecting the power cord (see page 9), 18. Do not attempt to raise, lower, or move the
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit. Do not use an extension
cord.
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 22.) You
must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
11. Use only a single-outlet surge suppressor that
is UL 1449 listed as a transient voltage surge
suppressor (TVSS). The surge suppressor
must have a UL suppressed voltage rating of
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21. When using iFIT.com CD’s and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
24. Inspect and tighten all parts of the treadmill
regularly.
25. Never insert or drop any object into any
opening.
26.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. When using iFIT.com CD’s and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
and incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
23. Always remove iFIT.com CD’s and videos
from your CD player or VCR when you are not
using them.
27. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If a decal is missing or illegible, please call
our Customer Service Department toll-free to order a free replacement decal (see HOW TO ORDER
REPLACEMENT PARTS on page 31). Apply the decal in the location shown.
Note: This decal is shown at 38% of actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new REEBOK® RTX 525
treadmill. The RTX 525 treadmill combines advanced
technology with innovative design to let you enjoy an
effective form of cardiovascular exercise in the conve-
nience and privacy of your home. And when you’re not
exercising, the unique RTX 525 can be folded up, re-
quiring less than half the floor space of other treadmills.
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please mention the product model
number and serial number when calling. The model
number is RBTL15500. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Book Holder
Hand Weight Holder*
Console
Handrail
Water Bottle Holder
(Bottle not included)
Key/Clip
Lock Knob
LEFT SIDE
RIGHT SIDE
Walking Belt
On/Off Switch
Circuit Breaker
Foot Pad
Power Cord
Cushioned Walking Platform
Rear Roller
Adjustment Bolts
*For information about optional
hand weights, see page 21.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires your own Phillips screw-
driver
and rubber mallet
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
1
Uprights (69) until the treadmill is in the position shown.
Insert one of the Extension Legs (102) into the treadmill
69
as shown. Make sure that the Extension Leg is turned so
the Base Pad (99) is on the bottom. Note: It may be help-
ful to tip the Uprights (69) forward as you insert the
Extension Leg.
Insert the other Extension Leg (not shown) in the same
way.
102
99
2. With the help of a second person, carefully tip the
Uprights (69) down as shown. Make sure that the
Extension Legs (102) remain in the Uprights.
2
Attach each Extension Leg (102) with two of the four 3/4”
Screws (100). Note: If there are square rubber bumpers
on the bottom of the Uprights (69), remove them.
99
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position.
69
Note: One replacement Base Pad (99) may be included.
If a Base Pad becomes worn and needs to be replaced,
use the replacement Base Pad.
69
102
110
100
100
102
99
3. Remove the Handrail Extension (66) from the Right Foam
Grip (75), which has a large cutout in the left side. Insert
the Handrail Extension into the post on the right Upright
(69) as shown. Note: Be careful not to pinch the wires
in the post. Make sure that the wires in the post are cen-
tered. Align the holes in the Handrail Extension (66) with
the holes in the post. If necessary, tap the Handrail
Extension with a rubber mallet to fully insert it. Next, attach
the Handrail Extension by tightening two Small Screws
(67) into the indicated holes.
3
67
66
Cutout
75
69
Post
Wires
Slide the Right Foam Grip (75) as far as possible onto the
post on the right Upright (69). It may be helpful to apply
soapy water to the Handrail Extension (66).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Refer to drawing 4a. Make sure that the tab on the Right
Foam Grip (75) is inserted into the slot between the post
and the Console Base (82).
4b
4a
82
Post
75
82
Refer to drawing 4b. Make sure that the front edge of the
Right Foam Grip (75) is under the Console Base (82) as
shown. Tighten one of the two Foam Grip Screws (33)
into the side of the Right Foam Grip as shown. Note: It
may be necessary to pull the Right Foam Grip outward
(see arrow A) to align the Screw with the hole in the post.
A
Tab
33
75
Attach the other Handrail Extension and the Left Foam
Grip (not shown) as described in step 3 and this step.
5. Press the Lock Knob Sleeve (70) into the left Upright (69).
If necessary, use a rubber mallet to tap the Lock Knob
Sleeve into the Upright.
5
68
Make sure that the Lock Pin Collar (72) and the Spring (71)
are on the Lock Pin (74). (Note: If there are two Lock Pin
Collars, place one on each side of the Spring.) Insert the
Lock Pin into the left Upright (69) and tighten the Lock
Knob (68) onto the Lock Pin.
69
71
72
70
74
6. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 24). To protect the floor or carpet
from damage, place a mat under the treadmill.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE CHEST PULSE MONITOR
HOW TO PUT ON THE CHEST PULSE MONITOR
each use, it may remain activated longer than nec-
essary, draining the battery prematurely.
The chest pulse monitor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
one end of the sensor unit, as shown in the inset draw-
ing. Press the end of the sensor unit under the buckle
on the chest strap. The tab should be flush with the
front of the sensor unit.
• Store the chest pulse monitor in a warm, dry place.
Do not store the chest pulse monitor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse monitor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° Fahrenheit (50°
Celsius) or below 14° Fahrenheit (-10° Celsius).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse monitor.
Chest Strap
Tabs
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Tab
CHEST PULSE MONITOR TROUBLE-SHOOTING
Sensor
Unit
The instructions on the following pages explain
how the chest pulse monitor is used with the con-
sole. If the chest pulse monitor does not function
properly, try the steps below.
Buckle
Sensor Unit
Next, wrap the
chest pulse moni-
tor around your
chest and attach
the other end of
the chest strap to
the sensor unit.
Adjust the length
of the chest strap,
if necessary. The
chest pulse moni-
• Make sure that the chest pulse monitor is under your
clothing, tight against your skin, and as high under
the pectoral muscles or breasts as is comfortable.
The logo on the sensor unit must be facing forward
and be right-side-up. Note: If the chest pulse monitor
does not function when positioned as described, try
moving it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
tor should be under your clothing, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side.
The electrode areas are the areas covered by shallow
ridges. Using saline solution such as saliva or contact
lens solution, wet both electrode areas. Return the
sensor unit to a position against your chest.
• The chest pulse monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
CHEST PULSE MONITOR CARE AND MAINTENANCE
• Thoroughly dry the chest pulse monitor after each
use. The chest pulse monitor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse monitor shuts off
when it is removed and the electrode areas are
dried. If the chest pulse monitor is not dried after
• The operation of the chest pulse monitor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
• The CR2032 battery may need to be replaced (see
page 25).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TREADMILL OPERATION
THE PERFORMANT LUBETM WALKING BELT
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
1
HOW TO PLUG IN THE POWER CORD
Grounded Outlet Box
Surge Suppressor
Grounding Pin
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
Grounding Pin
Grounded Outlet
Grounding Plug
installed by a qualified electrician.
2
Grounded Outlet Box
Adapter
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).
Surge Suppressor
Lug
Metal Screw
Use only a single-outlet surge suppressor that is UL
1449 listed as a transient voltage surge suppressor
(TVSS). The surge suppressor must have a UL sup-
pressed voltage rating of 400 volts or less and a mini-
mum surge dissipation of 450 joules. The surge sup-
pressor must be electrically rated for 120 volts AC and
15 amps.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual/Program Indicators
Display
Program Display
Display
Program Indicators
Note: If there is a thin sheet
of clear plastic on the face
of the console, remove it.
Key
Clip
The console also features new iFIT.com interactive
technology. IFIT.com technology is like having a per-
sonal trainer right in your home. Using the included
audio cable, you can connect the treadmill to your
home stereo, portable stereo, or computer and play
special iFIT.com CD programs (CD’s are available sep-
arately). IFIT.com CD programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout.
High-energy music provides added motivation. Each
CD features two programs designed by certified per-
sonal trainers.
CAUTION:
Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turn-
ing on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
• The heart rate monitor is not a medical de-
vice. Various factors may affect the accuracy
of heart rate readings. The heart rate monitor
is intended only as an exercise aid in deter-
mining heart rate trends in general.
In addition, you can connect the treadmill to your VCR
and TV and play iFIT.com video programs (videocas-
settes are available separately). Video programs offer
the same benefits as iFIT.com CD programs, but add
the excitement of working out with a class and an
instructor—the hottest new trend at health clubs.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
With the treadmill connected to your computer, you
and access audio programs and video programs di-
rectly from the internet. And by adding an optional up-
grade module to the treadmill, you can use virtually
endless features from our internet site. See
FEATURES OF THE CONSOLE
The advanced console offers an impressive array of
features to help you get the most from your exercise.
When the console is in the manual mode, the speed
and incline of the treadmill can be changed with a touch
of a button. As you exercise, the console will display
continuous exercise feedback. You can even measure
your heart rate using the chest pulse monitor.
www.iFIT.com for complete details. To purchase
iFIT.com CD’s or videocassettes, call toll-free 1-
800-735-0768. To purchase an optional iFIT.com
module, call toll-free 1-800-884-0620.
To use the manual mode of the console, follow the
steps beginning on page 11. To use a personal trainer
program, see page 12. To use a pulse program, see
page 14. To use an iFIT.com CD or video program,
see page 16. To use an iFIT.com program directly
from our internet site, see page 18.
Six certified personal trainer programs are also
offered. Each program automatically controls the
speed and incline of the treadmill to give you an effec-
tive low-, medium-, or high-intensity workout. In addi-
tion, two pulse programs control the speed and incline
of the treadmill to keep your heart rate within a preset
range during your workouts.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
and begin walking. As
you exercise, change
the speed of the walking
belt as desired by press-
ing the Speed buttons.
Plug in the power cord (see HOW TO PLUG IN
THE POWER CORD on page 9).
1
Each time a button is
Locate the on/off
2
pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. To change
the speed setting quickly, press the Quick Speed
buttons.
switch on the treadmill
On
near the power cord.
Position
Move the on/off switch
to the on position.
Stand on the foot pads
of the treadmill. Find
the clip attached to the
key and slide the clip
3
To stop the walking belt, press the Stop button.
The Time/Segment Time display will begin to
flash. To restart the walking belt, press the Start
button or the Speed + button.
onto the waistband of
your clothing. Next, in-
Change the incline of the treadmill as desired.
sert the key into the console. After a moment, the
displays and various indicators will light. Test the
clip by carefully taking a few steps backward
until the key is pulled from the console. If the
key is not pulled from the console, adjust the
position of the clip as needed.
5
6
To change the incline of
the treadmill, press the
Incline buttons. Each time
a button is pressed, the
incline will change by
0.5%. The incline range is
1.5% to 10%. Note: After the buttons are pressed,
it may take a moment for the treadmill to reach the
selected incline setting.
HOW TO USE THE MANUAL MODE
Follow your progress with the LED track and
the displays.
Insert the key fully into the console.
The LED Track—
When the manual
mode or the iFIT.com
1
See HOW TO TURN ON THE POWER above.
mode is selected, the
program display will
Select the manual mode.
2
show an LED track rep-
resenting 1/4 mile. As
you exercise, the indi-
cators around the track will light in sequence until
you have completed one 1/4 mile-lap. A new lap
will then begin.
When the key is in-
serted, the manual
mode will be selected
and the Manual indica-
tor will light. If a pro-
gram has been
selected, press the Program button repeatedly to
select the manual mode.
Distance/Incline/
Laps display—This dis-
play shows the distance
that you have walked, the
Put on the chest pulse monitor if desired.
3
incline level of the tread-
See HOW TO PUT ON THE CHEST PULSE
MONITOR on page 8.
mill, and the number of 1/4-mile laps you have
completed. The display will change from one num-
ber to the next every seven seconds. The Incline
indicator or the Laps indicator will light when the
incline level or the number of laps is shown. Note:
Each time the Incline buttons are pressed, the dis-
play will show the current incline setting for several
seconds.
Press the Start button or the Speed + button to
start the walking belt.
4
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Time/Segment Time
display—When the
manual mode or the
When you are finished exercising, remove the
key.
7
iFIT.com mode is se-
lected, this display will
show the elapsed time.
When a program is selected, the display will show
both the time remaining in the program and the
time remaining in the current segment of the pro-
gram. The display will alternate between one num-
ber and the other every seven seconds. The
Segment Time indicator will light when the seg-
ment time is shown.
Step onto the foot pads, press the Stop button,
and adjust the incline of the treadmill to the
lowest setting. The incline must be at the low-
est setting when the treadmill is folded to the
storage position or the treadmill will be dam-
aged. Next, remove the key from the console and
put it in a secure place. Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. See page 21 and turn off the
demo mode.
Calories/Fat Calories/
Pulse display—This
display shows the
approximate numbers of
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
calories and fat calories
you have burned (see
FAT BURNING on page 28). Every seven sec-
onds, the display will change from one number to
the other. The Fat Cals. indicator will light when
the number of fat calories is shown. This display
will also show your heart rate when the chest
pulse monitor is used.
HOW TO USE PERSONAL TRAINER PROGRAMS
Speed/Min-Mile
display—This display
shows the speed of the
walking belt and your
current pace (pace is
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page 11.
measured in minutes per
Select one of the personal trainer programs.
mile). Every seven seconds, the display will
change from one number to the other. The Min/
Mile indicator will light when your pace is shown.
2
When the key is in-
serted, the manual
mode will be se-
lected and the
Manual indicator
will light. To select
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To find which
one of the per-
unit of measurement is
sonal trainer programs, press the Program button
repeatedly until one of the six personal trainer pro-
gram indicators lights.
selected, hold down the
Stop button while inserting the key into the con-
sole. An “E” for English miles or an “M” for metric
kilometers will appear in the Speed/Min-Mile dis-
play. Press the Speed + button to change the unit
of measurement. When the desired unit of mea-
surement is selected, remove the key and then
reinsert it. Note: For simplicity, all instructions
in this manual refer to miles.
The console features two low-intensity programs,
one medium-intensity program, and three high-
intensity programs. The profiles on the console
show how the speed and incline of the treadmill
will change during the programs. The numbers
beside the profiles show the maximum speed and
incline settings for the programs. For example, the
upper left profile shows that the treadmill will reach
a maximum speed of 4 mph and a maximum
incline of 8% during the first low-intensity program.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The program dis-
play will show a
simplified profile of
the program you
have selected.
The Time/
Segment Time
display will show how long the program will last.
Note: Each time a segment ends and the speed
settings move one column to the left, if all of the
indicators in the Current Segment column are lit,
the speed settings will move downward so that only
the highest indicators in the columns will appear in
the program display. When the speed settings
move to the left again and not all of the indicators
in the Current Segment column are lit, the speed
settings will move back up.
Put on the chest pulse monitor if desired.
3
4
If the speed or incline setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons on the console. Every few times
one of the Speed buttons is pressed, an additional
indicator will light or darken in the Current Segment
column. If any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator may light or darken in those
columns as well. Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
in the program display will not move downward as
described above. When the current segment of
the program ends, the treadmill will automati-
cally adjust to the speed and incline settings
for the next segment.
See HOW TO PUT ON THE CHEST PULSE
MONITOR on page 8.
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time seg-
ments of different lengths. The Time/Segment
Time display shows both the time remaining in the
program and the time remaining in the current
segment. One speed setting and one incline set-
ting are programmed for each segment. The
speed setting for
To stop the program temporarily, press the Stop
button. The Time/Segment Time display will begin
to flash. To restart the program, press the Start but-
ton or the Speed + button. To end the program,
press the Stop button, remove the key, and then
reinsert the key.
the first segment
will be shown in
the flashing
Current Segment
column of the pro-
gram display. (The
Current Segment
incline settings are
not shown in the
program display.) The speed settings for the next
twelve segments will be shown in the twelve
columns to the right.
Follow your progress with the displays.
5
6
Refer to step 6 on page 11.
When the program is completed, remove the
key from the console.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se-
ries of tones will sound, and all speed settings will
move one column to the left. The speed setting for
the second segment will then be shown in the
flashing Current Segment column and the tread-
mill will automatically adjust to the speed and in-
cline settings for the second segment.
When the program is completed, make sure that
the incline of the treadmill is at the lowest set-
ting. Next, remove the key from the console and
put it in a safe place. Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. Refer to page 21 and turn off the
demo mode.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the Time/Segment Time display. The walking belt
will then slow to a stop.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
program. If you have al-
ready entered your age,
HOW TO USE PULSE PROGRAMS
go to step 4. If you have
not entered your age,
press the Incline buttons
to enter your age. Your
age will be shown in the Time/Segment Time dis-
play. Once you have entered your age, your
age will be saved in memory.
CAUTION:
If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the pulse pro-
grams. If you are taking medication regularly,
consult your physician to find whether the
medication will affect your exercise heart rate.
Put on the chest pulse monitor.
4
5
The chest pulse monitor must be worn when a
pulse program is used. See HOW TO USE THE
CHEST PULSE MONITOR on page 8. Note: A
pulse program can be started without a heart rate
reading; however, the speed and/or incline of the
treadmill will automatically decrease if your heart
rate is not detected during the program.
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page 11.
Select one of the pulse programs.
2
When the key is
inserted, the man-
ual mode will be
selected and the
Manual indicator
will light. To select
Press the Start button.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
one of the pulse
programs, press the Program button repeatedly
until one of the two pulse program indicators
lights.
Each pulse pro-
gram is divided into
twenty-three, one-
Current Segment
minute segments.
One heart rate set-
ting is programmed
for each segment.
The heart rate set-
ting for the first
segment will be shown in the flashing Current
Segment column of the program display. The
heart rate settings for the next twelve segments
will be shown in the twelve columns to the right.
The profiles on the console show how the target
heart rate will change during the pulse programs.
The numbers beside the profiles show the heart
rate range for the programs. For example, the
upper profile shows that the treadmill will keep
your heart rate at 65% to 85% of your maximum
heart rate during the first program. (Your maxi-
mum heart rate is estimated by subtracting your
age from 220. For example, if you are 25 years
old, your maximum heart rate is 195 beats per
minute.)
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a se-
ries of tones will sound, and all heart rate settings
will move one column to the left. The heart rate
setting for the second segment will then be shown
in the flashing Current Segment column and the
speed and/or incline of the treadmill will automati-
cally change to bring your heart rate closer to the
heart rate setting for the second segment.
When a pulse pro-
gram is selected,
the program dis-
play will show a
simplified profile of
the program.
Enter your age.
3
When a pulse program is
selected, the letters
“AGE” will appear in the
Distance/Incline/Laps
display. You must enter
your age to use a pulse
If your heart rate is not detected during the pro-
gram, the letters “PLS” will flash in the Calories/Fat
Calories/Pulse display. (See CHEST PULSE
MONITOR TROUBLE-SHOOTING on page 8.) The
speed and/or incline of the treadmill may also de-
crease until your heart rate is detected.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 17.
To use iFIT.com CD’s or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
16. Note: To purchase iFIT.com CD’s or videocas-
settes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
Insert the key fully into the console.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
1
CH
3
4
OUT
See HOW TO TURN ON THE POWER on page 11.
AUDIO OUT
RIGHT
LEFT
Select the iFIT.com mode.
2
Audio
Cable
Adapter
When the key is in-
serted, the manual
mode will be selected
and the Manual indica-
tor will light. To use
iFIT.com CD’s or video-
cassettes, press the Program button repeatedly
until the iFIT.com indicator lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the AUDIO
OUT jack on your VCR.
Insert the iFIT.com CD or videocassette.
3
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Press the PLAY button on your CD player or
VCR.
B
4
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Segment Time dis-
play is flashing, press the Start button or the
Speed + button on the console. The treadmill will
not respond to a CD or video program when the
Time/Segment Time display is flashing.
RCA Adapter
Adapter
Audio
Cable
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA adapter (available at
electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA adapter. Plug the RCA adapter into the LINE
OUT jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Adapter
Audio
Adapter
Cable
Wire removed from
LINE OUT jack
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CD’s, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
16 and 17 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 18 for connecting instructions. To
use iFIT.com programs directly from our internet
site, the treadmill must be connected to your home
computer. See page 17 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
Audio
Cable
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
16
Download from Www.Somanuals.com. All Manuals Search And Download.
The program will continue until the heart rate set-
ting for the last segment is shown in the Current
Segment column and the Time/Segment Time
display counts down to zero. The walking belt will
then slow to a stop.
the speed cannot be increased any further. When
the incline reaches the highest setting, the speed
cannot be decreased any further.
To stop the program, press the Stop button. Pulse
programs should not be stopped temporarily and
then restarted. To use the pulse program again,
reselect the program and start it at the beginning.
While the program is in progress, minor adjust-
ments can be made to the speed or incline of the
treadmill with the Speed or Incline buttons.
However, if you increase the speed, the incline
will automatically decrease; if you decrease the
speed, the incline will increase. If you increase the
incline, the speed will decrease; if you decrease
the incline, the speed will increase. The console
will always attempt to keep your heart rate near
the heart rate setting for the current segment.
Note: When the incline reaches the lowest setting,
Follow your progress with the displays.
6
7
Refer to step 6 on page 11.
When the program is completed, remove the
key from the console.
See step 6 on page 13.
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• adjust the volume of your CD player or VCR. If
the volume is too high or too low, the console
may not detect the program signals
• make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the pro-
gram, press the Start button or the Speed + but-
ton. After a moment, the walking belt will begin to
move at 1.0 mph. When the next “chirp” is
heard, the speed and incline will change to the
next settings of the CD or video program. The
program can also be stopped by pressing the
Stop button on your CD player or VCR.
• if you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
Follow your progress with the LED track and
the displays.
5
6
See step 6 on page 11.
When the program is completed, remove the
key.
When the CD or video program is completed, the
walking belt will stop and the Time/Segment Time
display will begin to flash. Note: To use another
CD or video program, press the Stop button or re-
move the key and go to step 1 on page 16.
See step 6 on page 13.
CAUTION:
Always remove
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
iFIT.com CD’s and videocassettes from
your CD player or VCR when you are fin-
ished using them.
• make sure that the iFIT.com indicator is lit and
that the Time/Segment Time display is not
flashing. If the Time/Segment Time display is
flashing, press the Start button or the Speed
+ button on the console
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
pads. Find the clip attached to the key and slide
the key onto the waistband of your clothing.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR INTERNET SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
access a selection of programs that interactively con-
trol your treadmill to help you achieve your specific ex-
ercise goals. In addition, you can play iFIT.com audio
and video programs directly from the internet. By
adding an optional upgrade module to the console, you
can use virtually endless features on our internet site.
tional iFIT.com module, call toll-free 1-800-884-0620.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
To use programs from our internet site, the treadmill
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 17. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our internet site.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the pro-
gram, press the Start button or the Speed + but-
ton. After a moment, the walking belt will begin to
move at 1.0 mph. When the next “chirp” is
heard, the speed and incline will change to the
next settings of the program.
Follow the steps below to use a program from our
internet site.
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page 11.
Select the iFIT.com mode.
When the program is completed, the walking belt
will stop and the Time/Segment Time display will
begin to flash. Note: To use another program,
press the Stop button and go to step 5.
2
When the key is in-
serted, the manual
mode will be selected
and the Manual indica-
tor will light. To use a
program from our inter-
net site, press the Program button repeatedly until
the iFIT.com indicator lights.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Segment Time display is not flashing.
In addition, make sure that the audio cable is
properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
Go to your computer and start an internet
connection.
3
Follow your progress with the LED track and
the displays.
Start your web browser, if necessary, and go to
8
9
4
See step 6 on page 11.
Follow the desired links on our internet site to
select a program.
5
When the program has ended, remove the key.
See step 6 on page 13.
Read and follow the on-line instructions for using a
program.
Follow the on-line instructions to start the
program.
6
When you start the program, an on-screen count-
down will begin.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
OPTIONAL HAND WEIGHTS
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
Hand weights let you ex-
ercise your upper-body
while you walk on the
treadmill. The hand
weights fit into convenient
holders in the console.
To purchase hand
weights, call toll-free
1-800-999-3756.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown:
WARNING:
Do not use the hand
The Distance/Incline/Laps
display will show the total
number of miles that the walk-
ing belt has moved.
weights at speeds faster than a walk. Using
hand weights and not holding the handrails may
compromise your ability to maintain your bal-
ance. Exercises using hand weights should be
attempted only by experienced users.
The Time/Segment Time dis-
play will show the total num-
ber of hours the treadmill has
been used.
THE OPTIONAL IFIT.COM MODULE
By adding an optional
iFIT.com module to the
treadmill, you can use vir-
tually endless features
from our internet site.
Imagine on-line competi-
tions, personal training
sessions via the internet,
and the ability to use your computer to track your pro-
grams. For information about purchasing the op-
tional iFIT.com module, call toll-free 1-800-884-
0620.
An “E,” for english miles, or
an “M,” for metric kilometers,
will appear in the Speed/ Min-
Mile display. Press the Speed
+ button to change the unit of
measurement.
IMPORTANT: The
Calories/Fat Calories/Pulse
display should be blank. If a
“d” appears in the display, the
console is in the “demo”
mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence, although
the buttons on the console will not operate. If a “d” ap-
pears in the Calories/Fat Calories/Pulse display
when the information mode is selected, press the
Speed – button so the Calories/Fat Calories/Pulse
display is blank.
To exit the information mode, remove the key from the
console.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be per-
manently damaged. Next, unplug the power cord. CAU-
TION: You must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown at
the right. CAUTION: To decrease the possibility of injury,
bend your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather than
your back. Raise the treadmill about halfway to the vertical
position.
2. Move your right hand to the position shown and hold the
2
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the latch pin is
aligned with the hole in the catch. Insert the latch pin into the
catch. Make sure that the latch pin is fully inserted into
the catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage
position in temperatures above 85° Fahrenheit.
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the pin on the
lock knob is inserted into the slot in the catch.
Crossbar
1. Hold the handrails as shown and place one foot against a
wheel. It may be helpful to grab the crossbar as you tip the
treadmill.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce the
risk of injury, use extreme caution while moving the
treadmill. Do not attempt to move the treadmill over an
uneven surface.
Base
Front Wheels
3. Place one foot on the base, and carefully lower the treadmill
until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the upper end of the treadmill with your right hand. Using your left hand, pull
the latch knob to the left. Pivot the treadmill down until the frame is past the pin. Slowly release the latch knob.
2. Refer to drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not
drop the treadmill frame to the floor. CAUTION: To decrease the possibility of injury, bend your legs
and keep your back straight.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power turns does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppres-
sor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor
must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation
of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps.
Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill near
c
the power cord. If the switch protrudes as shown, the
circuit breaker has tripped. To reset the circuit
breaker, wait for five minutes and then press the
switch back in.
Tripped
Reset
On
set
d
d. Check the on/off switch located on the treadmill near
the power cord. The switch must be in the on position.
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com
CD’s and videos are played
SOLUTION: a. With the key inserted into the console, press one of the Incline buttons. While the incline is
changing, remove the key. After a few seconds, re-insert the key. The treadmill will automati-
cally rise to the maximum incline level and then return to the minimum level. This will recalibrate
the incline.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically
rated for 120 volts AC and 15 amps.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
3”–4”
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-free.
PROBLEM: The walking belt is off-center
SOLUTION: a. If the walking belt has shifted to the left, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn the left rear roller adjustment bolt
clockwise, and the right bolt counterclockwise, 1/4 of a
turn each. Be careful not to overtighten the walking belt.
Plug in the power cord, insert the key and run the tread-
mill for a few minutes. Repeat until the walking belt is
centered.
a
b. If the walking belt has shifted to the right, first re-
move the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller adjust-
ment bolt counterclockwise, and the right bolt clockwise,
1/4 of a turn each. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key and
run the treadmill for a few minutes. Repeat until the
walking belt is centered.
b
PROBLEM: The walking belt slips when walked on
SOLUTION: a. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn both rear roller adjustment bolts
clockwise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each side of
the walking belt 3 to 4 inches off the walking platform.
Be careful to keep the walking belt centered. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat until the walking belt
is properly tightened.
a
PROBLEM: When the heart rate monitor is used, the letters “PLS” appear in the PULSE display or the
displayed heart rate is excessively high or low
SOLUTION: a. Refer to CHEST PULSE MONITOR TROUBLE-SHOOTING on page 8.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and unplug the
power cord. Carefully tip the treadmill down as
shown in drawing a. Remove the Screws (39, 83) from
the hood. Raise the Uprights (69) and carefully re-
move the hood.
a
39
69
83
Locate the Reed Switch (10) and the Magnet (7) on
the left side of the Pulley (8). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the 1/2”
Screw (67) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
Top View
1/8”
8
67
10
7
PROBLEM: The chest pulse monitor does not function properly
SOLUTION: a. If the chest pulse monitor does not function properly, see CHEST PULSE MONITOR TROUBLE-
SHOOTING on page 8.
b. If the chest pulse monitor still does not function properly, the battery
Battery Cover
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the “open” position. Remove
the cover.
Remove the old battery from the sensor unit. Insert a new CR 2032
battery, making sure that the writing is on top. In addition, make sure
that the rubber gasket is in place in the sensor unit. Replace the bat-
tery cover and turn it to the closed position.
Battery
Cover
Battery
Rubber
Gasket
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REEBOK UNIVERSITY
Reebok University was launched in 1993 to fulfill a
vision to establish a “university without walls” that
develops quality, researched, state-of-the-art fitness
programming for the fitness industry throughout the
world.
WALKING AND REDUCED RISK FOR CARDIOVAS-
CULAR DISEASE
Several studies have found that regular walking at any
speed can increase HDL-C cholesterol (a high-density
lipoprotein which removes excess cholesterol from the
body) and can lower concentrations of blood triglyc-
erides (a storage form of fat), thus reducing the risk for
Working with the world’s best professionals, Reebok
University has created a host of original programs,
such as Step Reebok®, Walk ReebokSM, Slide ReebokSM cardiovascular disease.
and Reebok City JamSM. The industry has adopted
Reebok programming as the “gold” standard. Our
guidelines and terminology are used by fitness profes-
sionals and participants around the world, and our
exceptional programming has been approved in the
United States by AFAA and ACE for continuing educa-
tion credits.
Duncan and his colleagues3 concluded that exercise
does not have to be vigorous to reduce cardiovascular
risk factors. In other words, people who choose to
stroll rather than walk briskly can reduce their risk for
cardiovascular disease.
After studying the physical activity patterns of 17,000
Harvard alumni over a 20-year period, Paffenbarger
and his colleagues4 concluded that walking as little as
five city blocks per day can reduce the risk of cardio-
vascular disease, and walking 2 miles per day can
reduce the risk of a heart attack by 28% or more.
Therefore, while walking at a fast pace will improve
aerobic fitness, walking at any speed (slow or fast) can
reduce a person's risk for heart disease.
WALKING AND CARDIORESPIRATORY
ENDURANCE
Scientific studies confirm
that walking at a moder-
ate to brisk pace can
enhance aerobic fit-
ness. Rippe and his
colleagues1 found that of
500 subjects tested, 67%
of the men and 90% of the
women were able to reach
their target heart rates by
walking 4 to 4.5 miles
per hour.
WALKING AND WEIGHT REDUCTION
Walking is an excellent activity for burning calories.
The steeper the incline and/or the faster the speed, the
more calories are burned. For example, a 150-pound
person walking at 3.5 miles per hour on flat ground will
burn about 300 calories per hour. This same person
will burn 400 calories per hour on a gentle 4% incline
and 500 calories per hour on a steeper 10% incline. If
this person speeds the pace up to 4 miles per hour on
level ground, 350 calories will be burned in one hour.5
Pollock and his colleagues2 found that middle-aged
men who walked at a pace of 3.5 to 4.5 miles per hour
for 40 minutes four times per week had the same car-
diovascular improvements as men the same age who
jogged for 30 minutes three times per week. Although
the intensity of exercise was lower for the walkers than
the runners, the increased duration and frequency of
walking provided the walkers with similar aerobic ben-
efits as the runners.
It should be noted that participants who do not wish to
walk at faster speeds can burn a comparable number
of calories by walking for longer periods of time.
WALKING AND BONE DENSITY
Osteoporosis is a major health problem in the United
States, affecting an estimated 15 to 30 million people.
An age-related disorder, osteoporosis reduces the
density of bones. This disease can be life-threatening
since many older people die as a result of complica-
tions suffered from broken bones. Adequate calcium in
the diet and weight-bearing exercises seem to reduce
the risk of osteoporosis.
On the basis of current research, it seems clear that
walking at a moderate to brisk pace can be an excel-
lent aerobic activity.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Several studies have reported that regular walking at
moderate to brisk speeds appears to increase bone
density. Specifically, Fradin and his colleagues6 found
that 70-year-old subjects who walked at least 30 min-
utes per day had higher bone mineral content than
subjects who walked less than 30 minutes per day.
Jones and his colleagues7 reported that sedentary
women (aged 30 to 61 years old) who began a regular
walking program and continued for one year increased
their bone density.
During a 24-week study, not one of 59 participants who
walked five days a week at speeds between 3 and 5
miles per hour sustained a walking-related injury that
necessitated consulting with a physician. Carroll and
his colleagues10 reported that 14% of the elderly sub-
jects participating in a walking study suffered training-
related orthopedic injuries, mostly to the lower leg and
foot. The majority of injuries occurred in the group as-
signed to "fast walking."
It is important to note that all forms of exercise have
Since walking can be comfortably performed by people some degree of risk associated with the activity.
of any age, walking appears to be practical and effec-
tive in reducing a person's risk for developing osteo-
porosis.
Generally, the less mechanical stress on the muscu-
loskeletal system, the less risk of becoming injured.
Because of the low-impact nature of walking, the inci-
dence of injury appears to be low when compared to
other high-impact activities.
WALKING AND STRESS REDUCTION
There are many stressors in today's society, including
economic concerns, work-related pressures and the
need to balance career goals with home responsibili-
ties. People who are unable to cope with these types of
stressors are often tense and anxious, and may even
become physically or psychologically ill.
REFERENCES
1. Rippe, J., Ross, J., et. al. “Cardiovascular effects of walking.”
(Abstract), Proceedings of the Second International Conference
on Physical Activity, Aging and Sports, July, 1985, p. 47.
2. Pollock, M., Miller, H. Jr., et. al. “Effects of walking on body com-
position and cardiovascular function of middle-aged men.”
Journal of Applied Physiology, 1971, 30:126–130.
3. Duncan, J., Gordon, N., et. al. “Women walking for health and fit-
ness. How much is enough?” Journal of the American Medical
Association, 1991, 266(23):3295–9.
4. Paffenbarger, R., Hyde, R., et.al. “Physical activity, all-cause
mortality and longevity of college alumni.” New England Journal
of Medicine, 1986, 314:605–613.
Researchers have found that exercise is one way to
help people reduce stress. For example, subjects who
engaged in a regular aerobic conditioning program and
who altered their diets experienced significant gains in
self-concept, feelings of well-being and reduced
depression.8
5. “Better walking workouts.” University of California at Berkeley
Wellness Letter, 1992, 8(12):4–5.
6. Fradin, K. Grimby, G., et. al. “Walking habits and health-related
factors in a 70-year-old population,” Gerontology, 1991,
37(5):281–8.
7. Jones, P., Hardman, A., et. al. “Influence of brisk walking on the
broadband ultrasonic attenuation of the calcaneus in previously
sedentary women aged 30–61 years.” Calcified Tissue
International, 1991, 49(2):112–5.
Cramer and his colleagues9 specifically examined the
effect of brisk walking on mildly obese sedentary
women and found that walking improved general psy-
chological well-being. Walking therefore appears to be
an effective tool for improving psychological well-being.
8. Blair, S., Collingwood, T., et. al. “Health Promotion for Educators:
Impact on Health Behaviors, Satisfaction, and General Well-
Being,” American Journal of Public Health, 1984, 74:147–49.
9. Cramer, S., Nieman D., et. al. “The effects of moderate exercise
training on psychological well-being and mood state in women.”
Journal of Psychosomatic Research, 1991, 35(4–5):437–49.
10. Carroll, J., Pollack, M., et. al. “Incidence of injury during moderate
and high intensity walking in the elderly.” Journal of Gerontology,
1992, 47(3):M61–6.
WALKING AND INJURIES
Walking is often associated with a low injury rate.
Walking is considered to be a "low impact" activity be-
cause one foot remains in contact with the ground at all
times. Walking at speeds of 3 miles per hour produces
vertical impact forces that are around 1.25 times body
weight, whereas running at 7 miles per hour increases
vertical impact forces to more than 2.5 times body
weight.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING
Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for individuals over the age of 35 or indi-
viduals with pre-existing health problems.
The heart rate monitor is not a medical de-
vice. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is in-
tended only as an exercise aid in determining
heart rate trends in general.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for pro-
longed periods of time. This increases the demand on
the heart to pump blood to the muscles and on the
lungs to oxygenate the blood. For aerobic exercise, ad-
just the speed or incline of the treadmill until your heart
rate is near the highest number in your training zone.
The following guidelines will help you to plan your ex-
ercise program. Remember—these are general guide-
lines only. For more detailed exercise information, ob-
tain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exer-
cise—never hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
You can measure your heart rate using the chest pulse
monitor. If your heart rate is too high or too low, adjust
the speed or incline of the treadmill accordingly.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may
complete up to five workouts each week if desired. The
key to success is to make exercise a regular and en-
joyable part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
5
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps
and hip muscles.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—MODEL NO. RBTL15500
R0601A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
4
5
6
7
8
9
1
1
1
1
2
2
1
1
8
1
Foot Pad (Left)
Deck Pad (Left)
Foot Pad (Right)
Deck Pad (Right)
Frame Pivot Bolt
Frame Pivot Spacer
Magnet
Front Roller/Pulley
Frame Pivot Nut
Reed Switch/Sensor
Wire
Latch Assembly
Reed Switch Clip
Lift Frame
Star Washer
Idler Assembly
Motor
50
51
52
53
54
55
56
1
2
1
6
4
2
5
Belly Pan
98
99
1
4
6
1
2
2
2
1
2
2
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
Upright Wire Harness
Thick Base Pad
3/4” Screw
Tension Washer
Extension Leg
Extension Cap
Incline Warning Decal
Shock
Extension Leg Assmy.
Hand Weight
Book Holder
Power Cord Grommet
Frame
Catch Screw
Catch
Audio Wire
Walking Belt
15” Wire Harness
20” Wire Harness
Cage Nut
Idler Arm Bolt
Pulley Spacer
Pulley Nut
Idler Spring
Frame Guide
Motor Isolator Plate
Motor Bushing
Frame Guide Spacer
Pulse Sensor
12” White Wire, M/F
8” White Wire, 2F
8” White Wire, M/F
14” Blue Wire, 2F
10” Blue Wire, 2F
4” Blue Wire, 2F
4” Black Wire, 2F
12” Green Wire, 2/Ring
8” Green Wire, F/Ring
User's Manual
Endcap Spacer
Walking Platform
Platform Screw
Rear Platform Screw
Rear Isolator
Ground Screw/
Controller Screw
Ground Wire
Rear Endcap
Rear Roller Adj. Bolt
Warning Decal
Allen Wrench
Rear Roller
Chest Pulse Strap
chest pulse monitor
Left Foam Grip
Handrail Extension
1/2” Screw
Lock Knob
Upright
Lock Knob Sleeve
Spring
Lock Pin Collar
Pin Clip
100
101
102
103
104
105
106*
107**
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
#
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76**
77**
1
1
2
1
1
1
1
1
1
2
8
1
1
1
1
1
1
1
1
1
1
10
11*
12
13
14
15*
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1
1
1
3
1
1
1
1
1
1
1
2
1
2
4
1
5
1
1
1
1
1
6
9
Idler Arm
Motor Belt
Idler Pulley
Tension Bolt
Incline Motor Bolt
Motor Bolt
Hood
Incline Motor Bolt
Plastic Stand-off
Power Board
Screw
Choke
Controller
Electronics Plate
8” Wire Harness
Front Roller Adj. Bolt
1 1/4” Screw
Roller Washer/
Platform Washer
Front Roller Nut
Incline Motor
Incline Motor Stop
Belly Pan
Belly Pan Screw (Long)
Static Decal
Circuit Breaker
Power Cord
On/Off Switch
Left Endcap Insert
Belt Guide Screw
Belt Guide
Lock Pin
Right Foam Grip
iFIT.com Module
iFIT.com
Videocassette
iFIT.com CD
Upright Endcap
Belly Pan Screw
Console Base
Console
Console Screw
Key/Clip
10’ iFIT.com Wire
Jack
Console Back Screw/
Base Pad Screw
Console Back
Releaseable Tie
Cable Tie Screw
Cable Tie Clamp
8” Cable Tie
Lift Pivot Bolt
Wheel Bolt
Wheel
78**
79
80
81
82
83
84
85
86
87
1
2
4
1
1
8
1
1
1
#
#
#
#
#
#
#
#
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
1
1
1
1
2
2
1
1
1
1
4
2
4
4
16
#
10
* Includes all parts shown in box
**For information about the optional
hand weights, see page 19. For in-
formation about the iFIT.com mod-
ule, call toll-free 1-800-884-0620.
For information about iFIT.com
CD’s or videocassettes, call toll-
free 1-800-735-0768.
88
89
90
91
92
93
94
95
96
97
1
1
1
1
1
2
2
2
1
1
Isolator
Isolator Screw
Fastener
Right Endcap Insert
Grommet
# These parts are not illustrated
30
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information:
• The MODEL NUMBER of the product (RBTL15500)
• The NAME of the product (REEBOK® RTX 525 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 30).
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire REEBOK® RTX 525 (“Product”) is warranted to be free of all defects in material and
workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the motor for three years after the date of
purchase. The belt and deck are covered for two years after the date of purchase. All mechanical components are covered
for two years after the date of purchase. All electrical components are covered for two years after the date of purchase.
Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or com-
ponent, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized service
provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to use,
operate, and maintain as set out in your User’s Manual (“Manual”).
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of
the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to
do the periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfac-
tion.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-800-999-3756 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary,
arrange for service where your Product is located or advise you how to ship the Product for service. Before shipping, al-
ways obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack your Product
(save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the product. Include a
letter explaining the product or problem and a copy of your proof of purchase if you believe the service is covered by war-
ranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use
or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits,
loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states
do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not
apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or
fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow
limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 170694 R0601A
Printed in USA © 2001 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—MODEL NO. RBTL15500
R0601A
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—MODEL NO. RBTL15500
R0601A
.
G R O U P
L I T
K i r k N P i R
e
O b D e U r g C T l l
a
Download from Www.Somanuals.com. All Manuals Search And Download.
|