®
Patent Pending
Model No. RBTL13910
Serial No.
USER'S MANUAL
Write the serial number in the space
above for future reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
we will guarantee complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this man-
ual for future reference.
Visit our website at
®
new products, prizes,
®
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Keep the power cord and the surge suppres-
sor protector away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
16. The treadmill is capable of high speeds. Adjust
the speed in small increments to avoid sudden
jumps in speed.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 275 pounds.
17. To reduce the possibility of the treadmill over-
heating, do not operate the treadmill continu-
ously for longer than one hour.
8. Never allow more than one person on the
treadmill at a time.
18. The heart rate monitor is not a medical de-
vice. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is in-
tended only as an exercise aid in determining
heart rate trends in general.
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth-
ing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
10. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
20. Do not raise, lower, or move the treadmill
until it is properly set up. (See HOW TO SET
UP THE TREADMILL on page 6 and HOW TO
FOLD AND MOVE THE TREADMILL on page
26.) You must be able to safely lift 45 pounds
(20 kg) to raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 9. To purchase a surge suppressor, see
your local REEBOK dealer or call 1-800-806-
3651 and order part number 146148.
21. Do not change the incline of the treadmill by
placing objects under the treadmill.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
26. Always remove iFIT.com CD’s and videos
from your CD player or VCR when you are not
using them.
23. Inspect and properly tighten all parts of the
treadmill regularly.
27. Never drop or insert any object into any
opening.
24. When using iFIT.com CD’s and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
28. This treadmill is intended for home use only.
Do not use this treadmill in any commercial,
rental, or institutional setting.
29.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
25. When using iFIT.com CD’s and videos, you
can manually override the speed and incline
settings by pressing the speed and incline
buttons. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on
the treadmill. If a decal is missing, or if it is not
legible, please call our Customer Service
Department, toll-free, to order a free replace-
ment decal (see HOW TO ORDER REPLACE-
MENT PARTS on page 35 of this manual).
Apply the decal in the location shown.
Note: The decal below is shown at 38% of actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new REEBOK® V 2000
treadmill. The V 2000 treadmill combines advanced
technology with innovative design to let you enjoy an
excellent form of cardiovascular exercise in the conve-
nience and privacy of your home. And when you’re not
exercising, the unique V 2000 can be folded up, requir-
ing less than half the floor space of other treadmills.
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please mention the product model
number and serial number when calling. The model
number is RBTL13910. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Reading Rack
Water Bottle
Holder (Bottle
not included)
Console
Handrail
Upright
Key/Clip
Lock Knob
On/Off Switch
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Rear Roller
Adjustment Bolt
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO SET UP THE TREADMILL
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. A rubber mallet
may be needed for
assembly.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
1
Uprights (65) until the treadmill is in the position shown.
65
2. Press the Lock Knob Sleeve (68) into the left Upright
2
(65). If necessary, use a rubber mallet to tap the Lock
Knob Sleeve into the Upright.
Remove the Lock Knob (67) from the Lock Pin (72).
Make sure that the Lock Pin Collar (70) and the Spring
(69) are on the Lock Pin. (Note: If there are two Lock Pin
Collars, place them on each side of the Spring.) Insert
the Lock Pin into the left Upright (65) and tighten the
Lock Knob onto the Lock Pin.
65
67
69
70
68
72
3. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see pages 27 and 28). To protect the floor or
carpet from damage, place a mat under the treadmill.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
HEART RATE MONITOR CARE AND MAINTENANCE
Before you use the heart rate monitor, please read all
instructions on this page and the following page.
• Thoroughly dry the heart rate monitor after each
use. The heart rate monitor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the heart rate monitor shuts off
when it is removed and the electrode areas are
dried. If the heart rate monitor is not dried after each
use, it may remain activated longer than necessary,
draining the battery prematurely.
The heart rate mon-
1
itor consists of two
components: the
chest strap and the
sensor unit.
Chest Strap
See drawing 2 and
attach the chest
strap to the sensor
unit. Insert one of
the tabs on the
chest strap through
one end of the sen-
sor unit. Make sure
to press the end of
the sensor unit
• Store the heart rate monitor in a warm, dry place. Do
not store the heart rate monitor in a plastic bag or
other container that may trap moisture.
• Do not expose the heart rate monitor to direct
sunlight for extended periods of time
Sensor Unit
Tab
• Do not expose the heart rate monitor to tempera-
tures above 122° Fahrenheit (50° Celsius) or below
14° Fahrenheit (-10° Celsius).
2
under the buckle on
the chest strap—
the tab should be
almost flush with
the sensor unit.
• Do not excessively bend or stretch the sensor unit
when using or storing the heart rate monitor.
Sensor
Unit
Buckle
• Clean the sensor unit periodically using a damp
cloth; never use alcohol, abrasives, or chemicals.
The chest strap may be hand washed and air dried.
Next, wrap the heart
rate monitor around
your chest and at-
tach the other end of
the chest strap to
the sensor unit.
Adjust the length of
the chest strap, if
necessary.
HEART RATE MONITOR TROUBLESHOOTING
The instructions on the following pages explain
how the heart rate monitor is used with the console.
If the letters “PLS” appear in the PULSE display or if
the displayed heart rate is excessively high or low,
try the steps below.
• Make sure that you are wearing the heart rate moni-
tor exactly as described at the left. If the heart rate
monitor does not function properly when positioned
as described, move it slightly lower or higher on your
chest.
The heart rate moni-
tor should be under
your clothing, tight
against your skin, and as high under the pectoral mus-
cles or breasts as is comfortable. Make sure that the
logo on the sensor unit is facing forward and is right-
side-up.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side.
The electrode areas are the areas covered by shallow
ridges. Using saline solution such as saliva or contact
lens solution, wet both electrode areas. Return the
sensor unit to a position against your chest.
• As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
• The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
Locate the battery cover
on the back of the sen-
sor unit. Insert a coin
into the slot in the cover
and turn the cover coun-
terclockwise to the
• The operation of the heart rate monitor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
“open” position. Remove
the cover.
Remove the old battery
from the sensor unit.
Insert a new CR 2032
battery, making sure
that the writing is on top.
In addition, make sure
that the rubber gasket is
in place in the sensor
unit. Replace the battery
cover and turn it to the
closed position.
• The CR2032 battery may need to be replaced.
Follow the steps at the right to replace the battery.
CR2032
Battery
Rubber
Gasket
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TREADMILL OPERATION
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the pos-
sibility of your treadmill being damaged, always
use a surge suppressor with your treadmill (see
drawing 1 at the right). To purchase a surge sup-
pressor, see your local REEBOK dealer or call 1-
800-806-3651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
9
Download from Www.Somanuals.com. All Manuals Search And Download.
H
N
O
A
B
F
G
F
C
J
I
K
E
E
F
D
L
Note: If there is a thin sheet of clear plastic
on the face of the console, remove it.
M
FEATURES OF THE CONSOLE
home stereo, portable stereo, or computer and play
special iFIT.com CD programs (CD’s are available sep-
arately). IFIT.com CD programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout.
High-energy music provides added motivation. Each
CD features two programs designed by certified per-
sonal trainers.
The advanced console offers an impressive array of
features to make your workouts more effective. When
the console is in the manual mode, the speed and
incline of the treadmill can be changed with a touch of
a button. As you exercise, the LED displays will provide
continuous exercise feedback.
The console also offers ten preset workout programs—
four fat burn programs that automatically control the
speed and incline of the treadmill to give you effective
fat-burning workouts; four aerobic programs that control
the speed and incline of the treadmill to provide optimal
aerobic exercise; and two pulse programs that change
the speed and incline to keep your heart rate within a
target range during your workouts.
In addition, you can connect the treadmill to your VCR
and TV and play iFIT.com video programs (videocas-
settes are available separately). Video programs offer
the same benefits as iFIT.com CD programs, but add
the excitement of working out with a class and an
instructor—the hottest new trend at health clubs.
With the treadmill connected to your computer, you
cess basic programs, audio programs, and video pro-
grams directly from the internet. Additional options are
You can even create your own custom workout pro-
grams and store them in memory for future use.
The console also features new iFIT.com interactive
technology. IFIT.com technology is like having a per-
sonal trainer right in your home. Using the included
audio cable, you can connect the treadmill to your
To purchase iFIT.com CD’s or videocassettes or an
optional iFIT.com module, call toll-free 1-800-735-
0768.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
H. LED Matrix—When the manual mode is selected,
the matrix will show your progress on an LED track.
When a workout program is selected, the matrix will
show the upcoming speed settings or target heart
rate settings of the program.
See the drawing on page 10.
A. ENTER Button—This button is used to enter age,
weight, and maximum heart rate settings.
I. MODE Button—This button is used to select the
manual mode, workout programs, and the iFit.com
mode.
B. + and – Buttons—These buttons are used to change
age, weight, and maximum heart rate settings.
C. USER Button—This button is used to select user
information. Up to three different users can store
age, weight, and maximum heart rate settings.
J. START Button—This button starts the walking belt.
K. LEARN Button—This button is used to program
speed and incline settings for custom programs.
D. QUICK SPEED Buttons—These buttons allow you
to quickly select speed settings to 10 mph.
L. STOP Button—This button stops the walking belt.
When the button is pressed, the LED displays will
pause and the TIME display will flash.
E. SPEED Buttons—These buttons control the speed
of the walking belt. Each time a button is pressed,
the speed will change by 0.1 mph; if a button is held
down, the speed will change in increments of 0.5
mph. The speed range is 0.5 mph to 12 mph.
M. Key with Clip—The key turns the console on and off.
The attached clip is designed to be worn on your
waistband. If the key is pulled from the console, the
power will automatically turn off.
F. LED Displays—These displays provide continuous
feedback of the calories and fat calories you have
burned, the speed of the walking belt, your current
pace, the distance you have walked or run, the
number of laps you have completed, and the
elapsed time. In addition, the PULSE display shows
your heart rate when the heart rate monitor is worn.
Note: The console can display speed and dis-
tance in either miles or kilometers (see page 14).
For simplicity, all instructions in this manual
refer to miles.
N. INCLINE Buttons—These buttons control the incline
of the treadmill. Each time a button is pressed, the
incline will change by 0.5%. The incline range is
1.5% to 10%.
O. INCLINE Display—This display shows the incline
level of the treadmill. The first indicator will light
when the incline is at 1.5%, the second indicator will
light when the incline is at 2% or 2.5%, the third in-
dicator will light when the incline is at 3% or 3.5%,
and so forth.
G. Manual/Program Indicators—These indicators show
when the manual mode, a workout program, or the
iFit.com mode is selected.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ENTER USER INFORMATION
CAUTION:
Before operating the
console, read the following precautions.
Each time the power is turned
on, the USER 1 indicator will
begin to flash. The console
allows up to three different
users to enter their weight,
their age, and a maximum
heart rate setting into the console.
• Do not stand on the walking belt when turn-
ing on the power or starting the walking belt.
• Always wear the clip (see M on page 10) while
operating the treadmill. If the key is pulled
from the console, the walking belt will stop.
• The treadmill is capable of high speeds;
adjust the speed in small increments.
If you enter your weight into the console, the CALS/
FAT CALS display will be more accurate. If you want to
use a pulse program, you must enter your age and a
maximum heart rate setting.
• To reduce the risk of electric shock, keep the
console dry. Avoid spilling liquid on the
console and use only a sealable water bottle.
If you want to enter your weight, your age, or a maxi-
mum heart rate setting, follow the instructions below.
Press the USER button.
HOW TO TURN ON THE POWER
1
Press the USER button
Make sure that the
on/off switch, located
on the front of the
to designate yourself as
user 1. The USER 1
indicator will remain lit
treadmill, is in the on
without flashing. Note: To
position.
designate yourself as
On
user 2 or user 3, press the USER button repeat-
edly. IMPORTANT: Each time you use the tread-
mill, make sure that the correct user is selected.
Next, make sure that the power cord is properly plugged
in (see page 9).
Enter your weight if desired.
2
The current weight set-
ting will be shown in the
CALS/FAT CALS display.
Press the + or – button to
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 10), and
slide the clip onto the waistband of your clothes. Next,
insert the key fully into the console. After a moment,
various displays and indica-
enter your weight. Each
button press will change
tors will light. Test the clip by
the weight setting by 1 pound; if a button is held
down, the weight setting will change in increments
of 5 pounds. When your weight is shown, press
the ENTER button. Note: Once your weight is
entered, it will be saved in memory, even when
the power cord is unplugged.
carefully taking a few steps
backward until the key is
pulled from the console. If
the key is not pulled from
the console, reposition the
clip on your waistband as needed. Then re-
insert the key fully into the console.
To use the manual mode of the console, follow the
steps beginning on page 13. To use a fat burn pro-
gram or an aerobic program, see page 15. To use a
pulse program, see page 16. To create and use a
custom program, see pages 18 and 19. To use an
iFIT.com CD or video program, refer to page 22. To
use an iFIT.com program directly from our internet
site, see page 24.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter your age if desired.
HOW TO USE THE MANUAL MODE
3
4
The current age setting
will be shown in the
PULSE display. Press
the + or – button to enter
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 12.
your age. Each button
press will change the age setting by 1 year; if a
button is held down, the age setting will change in
increments of 5 years. When your age is shown,
press the ENTER button. Note: Once your age is
entered, it will be saved in memory, even when the
power cord is unplugged.
Select user 1, 2, or 3.
2
When the key is in-
serted, user 1 will be se-
lected, as shown by the
USER 1 indicator. If you
have designated yourself
as user 2 or 3, press the
USER button repeatedly until the appropriate indi-
cator lights.
Enter a maximum heart rate setting if desired.
The current
maximum
heart rate set-
ting will be
shown in the
LED matrix.
Enter your weight if desired.
3
If you have not entered your weight, see HOW TO
ENTER USER INFORMATION on page 12.
When a pulse
program is
used, this is
Select the manual mode.
4
the highest level that your heart rate will reach dur-
ing the program. This setting is a percentage of
your estimated maximum heart rate. (Your esti-
mated maximum heart rate is 220 minus your age.
For example, if you are 30 years old, your esti-
mated maximum heart rate is 190.)
When the key is in-
serted, the manual
mode will be selected. If
you have selected a
workout program or the
iFIT.com mode, you can
select the manual mode again by pressing the
MODE button repeatedly until the manual indicator
lights.
If desired, you can change the maximum heart
rate setting by pressing the + and – buttons. Each
button press will change the setting by 1%; if a
button is held down, the setting will change in in-
crements of 5%. The setting can be from 65% to
85%. When the desired setting is shown, press the
ENTER button. Note: When the key is removed
from the console, the maximum heart rate setting
will be reset to 65%.
Press the START button or the SPEED + button
to start the walking belt.
5
A moment after the
button is pressed, the
walking belt will begin to
move at 1.0 mph. Hold
the handrails and begin
walking. As you exercise, change the speed of the
walking belt as desired by pressing the SPEED
buttons or the QUICK SPEED buttons. CAUTION:
Change the speed in small increments to avoid
sudden jumps in speed.
To stop the walking belt, press the STOP button.
The displays will pause and the TIME display will
begin to flash. To restart the walking belt, press
the START button or the SPEED
+
button.
Note: When either of the SPEED buttons is pressed,
the SPEED/PACE display will show the selected
speed setting for seven seconds. The display will
then show the actual speed of the walking belt.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: During the first few minutes that the treadmill
is used, inspect the alignment of the walking belt
and align it if necessary (see page 28).
How to select miles per
hour or kilometers per
hour: Speed can be dis-
played in either miles per
Adjust the incline as desired.
hour (mph) or kilometers
per hour (kph). To change
6
7
To vary the intensity of
the unit of measurement, first hold down the STOP
button while inserting the key into the console. The
SPEED/PACE display will show either an “E” for
English miles or an “M” for metric kilometers. Press
the SPEED + button to change the unit of measure-
ment. Then, remove and reinsert the key.
your workout, change the
incline of the treadmill as
desired by pressing the
INCLINE buttons Note:
After the INCLINE but-
tons are pressed, it will
take a moment for the
treadmill to reach the selected incline setting.
DISTANCE/LAPS
display—This display
shows the distance that
the walking belt has
moved and the number
of laps you have com-
Follow your progress with the LED track and
the LED displays.
pleted (one lap equals 1/4 mile). The display will
alternate between one number and the other every
seven seconds.
The LED
Track—The
LED track rep-
resents a dis-
Note: If the speed is displayed in miles per hour,
the distance will be displayed in miles; if the speed
is displayed in kilometers per hour, the distance
will be displayed in kilometers.
tance of 1/4
mile. As you
exercise, the
indicators
around the
TIME display—This
display shows the total
track will light one at a time until you have com-
pleted 1/4 mile. A new lap will then begin.
time that the walking belt
has been moving. Note:
CALS/FAT CALS
When a workout pro-
display—This display
gram is selected, this
shows the approximate
display will show the time remaining in the program.
numbers of calories and
fat calories you have
burned (see FAT BURN-
ING on page 32). Every seven seconds, the display
will change from one number to the other.
When you are finished exercising, stop the
walking belt and remove the key.
8
Step onto the foot rails, press the STOP button,
and change the incline of the treadmill to the
lowest setting. The incline must be at the low-
est setting when the treadmill is folded to the
storage position or the treadmill will be dam-
aged.
PULSE display—This
display shows your heart
rate when the heart rate
monitor is worn.
SPEED/PACE display—
This display shows the
speed of the walking belt
and your current pace
Next, remove the key from the console and put it
in a secure place. Finally, move the on/off switch to
the off position and unplug the power cord.
(pace is measured in min-
utes per mile). The dis-
play will alternate between one number and the
other every seven seconds. Note: When either of
the SPEED buttons is pressed, the display will
show the speed setting.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
matrix.) The
speed settings
for the next
twelve periods
will be shown
in the twelve
columns to the
right.
CURRENT PERIOD
HOW TO USE FAT BURN PROGRAMS AND
AEROBIC PROGRAMS
The four fat burn programs and the four aerobic pro-
grams automatically control the speed and incline of
the treadmill as they guide you through effective work-
outs.
Follow the steps below to use a fat burn program or an
aerobic program.
When only three seconds remain in the first period
of the program, both the CURRENT PERIOD col-
umn and the column to the right will flash, a series
of tones will sound, and all speed settings will
move one column to the left. The speed setting for
the second period will then be shown in the flash-
ing CURRENT PERIOD column and the treadmill
will automatically adjust to the speed and incline
settings for the second period.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 12.
Select user 1, 2, or 3.
2
See step 2 on page 13.
The program will continue in this way until the
speed setting for the last period is shown in the
CURRENT PERIOD column and the TIME display
counts down to zero. The walking belt will then
slow to a stop.
Enter your weight if desired.
3
If you have not entered your weight, see HOW TO
ENTER USER INFORMATION on page 12.
Select the desired program.
Note: Each time a period ends and the speed set-
tings move to the left, if all of the indicators in the
CURRENT PERIOD column are lit, the speed set-
tings may move downward so that only the highest
indicators in the columns will appear in the LED
matrix. When the speed settings move to the left
again and not all of the indicators in the CURRENT
PERIOD column are lit, the speed settings will
move back up.
4
When the key is inserted,
the manual mode will be
selected. To select a fat
burn program or an aer-
obic program, press the
MODE button repeatedly
until one of the four fat burn indicators or one of
the four aerobic indicators lights. The LED matrix
will show the first twelve speed settings of the pro-
gram you have selected. The SPEED/PACE dis-
play will flash the program’s maximum speed set-
ting and the INCLINE display will flash the pro-
gram’s maximum incline setting for ten seconds.
If the speed or incline setting for the current
period is too high or too low, you can manually
override the setting by pressing the SPEED or
INCLINE buttons. Every few times one of the
SPEED buttons is pressed, an additional indicator
will light or darken in the CURRENT PERIOD col-
umn. If any of the columns to the right of the
CURRENT PERIOD column have the same num-
ber of lit indicators as the CURRENT PERIOD col-
umn, an additional indicator may light or darken in
those columns as well. Note: If you manually ad-
just the speed setting so that all of the indicators in
the CURRENT PERIOD column are lit, the speed
settings in the LED matrix will not move downward
as described above. Note: If you manually over-
ride the speed or incline setting for the current
period, when the period ends the treadmill will
automatically adjust to the speed and incline
settings for the next period.
Press the START button or the SPEED + button
to start the program.
5
A moment after the button is pressed, the treadmill
will automatically adjust to the first speed and in-
cline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time periods
of different lengths. One speed setting and one in-
cline setting are programmed for each period. The
speed setting for the first period is shown in the
flashing CURRENT PERIOD column of the LED
matrix. (The incline settings are not shown in the
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program temporarily, press the STOP
button. The TIME display will begin to flash. To
restart the program, press the START button or the
SPEED + button. To end the program, press the
STOP button, remove the key, and then reinsert the
key.
HOW TO USE PULSE PROGRAMS
Pulse programs 1 and 2 automatically control the speed
and incline of the treadmill to keep your heart rate within
a preset range during your workouts.
Follow your progress with the LED displays.
Follow the instructions below to use pulse programs 1
or 2.
6
7
See step 7 on page 14.
Insert the key into the console.
When the program is completed, remove the
key.
1
See HOW TO TURN ON THE POWER on page 12.
Make sure that the incline of the treadmill is at
the lowest setting. The incline must be at the
lowest setting when the treadmill is folded to
the storage position or the treadmill will be
damaged.
Select user 1, 2, or 3.
2
See step 2 on page 13.
Enter your weight, your age, and a maximum
heart rate setting.
3
Next, remove the key from the console and put it in
a secure place. In addition, move the on/off switch
to the off position and unplug the power cord.
If you enter your weight into the console, the
CALS/FAT CALS display will be more accurate. To
use pulse programs 1 or 2, you must enter your
age and a maximum heart rate setting. If you
have not entered this information, see HOW TO
ENTER USER INFORMATION on page 12.
Put on the heart rate monitor.
4
The heart rate monitor must be worn when a pulse
program is used. (See HOW TO USE THE HEART
RATE MONITOR on page 7.) Note: A pulse pro-
gram can be started without a heart rate reading;
however, the speed and/or incline of the treadmill
will automatically decrease if your heart rate is not
detected during the program.
Select the desired program.
5
When the key is inserted,
the manual mode will be
selected. To select pulse
program 1 or 2, press the
MODE button repeatedly
until the pulse program 1
or 2 indicator lights. The first thirteen target heart
rate settings of the program you have selected will
appear in the LED matrix.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If your heart rate is not detected during the program,
the letters “PLS” will flash in the PULSE display
and the speed and/or incline of the treadmill will
automatically decrease. (See HEART RATE
MONITOR TROUBLE-SHOOTING on page 7.)
Press the START button or the SPEED + button
to start the program.
6
A moment after the button is pressed, the treadmill
will automatically adjust to the first speed and in-
cline settings for the program. Hold the handrails
and begin walking.
While the program is in progress, minor adjust-
ments can be made to the speed or incline of the
treadmill with the SPEED or INCLINE buttons.
However, if you increase the speed, the incline will
automatically decrease; if you decrease the speed,
the incline will increase. If you increase the incline,
the speed will decrease; if you decrease the incline,
the speed will increase. The console will always
attempt to keep your heart rate near the heart rate
setting shown in the CURRENT PERIOD column.
Note: When the incline reaches the lowest setting,
the speed cannot be increased any further. When
the incline reaches the highest setting, the speed
cannot be decreased any further.
Pulse pro-
grams 1 and 2
CURRENT PERIOD
consist of
twenty-three,
one-minute
periods. One
target heart
rate setting is
programmed
for each
period. The target heart rate setting for the first pe-
riod will be shown in the flashing CURRENT PE-
RIOD column of the LED matrix. The target heart
rate settings for the next twelve periods will be
shown in the twelve columns to the right.
To stop the program, press the STOP button. Pulse
programs should not be stopped temporarily and
then restarted. To use the pulse program again,
reselect the program and start it at the beginning.
When only three seconds remain in the first period
of the program, both the CURRENT PERIOD col-
umn and the column to the right will flash and a
series of tones will sound. All target heart rate
settings will then move one column to the left. The
target heart rate setting for the second period will
then be shown in the CURRENT PERIOD column.
Follow your progress with the LED displays.
7
8
See step 7 on page 14.
When the program is completed, remove the
key.
As the program progresses, the speed and/or
incline of the treadmill will change automatically to
keep your heart rate near the heart rate setting
shown in the CURRENT PERIOD column. The
program will continue until the heart rate setting for
the last period is shown in the CURRENT PERIOD
column and the TIME display counts down to zero.
The walking belt will then slow to a stop.
See step 7 on page 16.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
the first period
is shown in
the flashing
CURRENT
PERIOD col-
umn of the
LED matrix.
(The incline
settings are
not shown in
HOW TO CREATE CUSTOM PROGRAMS
CURRENT PERIOD
Custom programs 1 and 2 are workout programs that
you create. The programs control both the speed and
incline of the treadmill and can be up to 40 minutes
long. The programs are stored in memory and can be
changed as many times as desired.
Follow the steps below to create a custom program.
the matrix.) To program speed and incline settings
for the first period, simply adjust the speed and in-
cline of the treadmill to the desired levels with the
SPEED and INCLINE buttons. Every few times the
SPEED buttons are pressed, one additional indica-
tor will light or darken in the CURRENT PERIOD
column.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 12.
Select user 1, 2, or 3.
2
See step 2 on page 13.
When the first one-minute period of the program is
completed, a series of tones will sound and the cur-
rent speed and incline settings will be stored in
memory. All speed settings shown in the LED matrix
will then move one column to the left and the speed
setting for the second period will be shown in the
flashing CURRENT PERIOD column. Program
speed and incline settings for the second period as
described above. Repeat this procedure until you
have programmed speed and incline settings for as
many periods as desired. Programs can have up to
forty periods.
Enter your weight if desired.
3
If you have not entered your weight, see HOW TO
ENTER USER INFORMATION on page 12.
Select custom program 1 or 2.
4
When the key is inserted,
the manual mode will be
selected. To select a cus-
tom program, press the
MODE button repeatedly
until the custom 1 or 2 in-
dicator lights.
Note: To stop the program for a moment, press the
STOP button. The displays will pause and the
TIME display will begin to flash. To restart the pro-
gram, press the START or SPEED
+
button.
Press the START button or the SPEED + button
5
to start the program.
Press the STOP button, remove the key, and
then reinsert the key.
7
8
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
When you have programmed speed and incline
settings for as many one-minute periods as
desired, press the STOP button, remove the key,
and then reinsert the key. The speed and incline
settings that you have programmed and the length
of the program will be stored in memory. To use the
program again, see HOW TO USE CUSTOM PRO-
GRAMS on page 19.
Press the LEARN button and program the
desired speed and incline settings.
6
When the LEARN button
is pressed, the LEARN in-
dictor will light. Speed and
incline settings can be
programmed only when
the indicator is lit.
When the program is completed, remove the
key.
See step 7 on page 16.
Each program is divided into one-minute periods.
One speed setting and one incline setting can be
programmed for each period. The speed setting for
18
Download from Www.Somanuals.com. All Manuals Search And Download.
When only three seconds remain in the first period
of the program, both the CURRENT PERIOD col-
umn and the column to the right will flash and a
series of tones will sound. All speed settings will
then move one column to the left. The speed set-
ting for the second period will then be shown in
the CURRENT PERIOD column and the speed
and incline of the treadmill will adjust to the sec-
ond settings that you programmed previously.
HOW TO USE CUSTOM PROGRAMS
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
12.
Select user 1, 2, or 3.
2
3
The program will continue in this way until the
speed setting for the last period is shown in the
CURRENT PERIOD column and the TIME display
counts down to zero. The walking belt will then
slow to a stop.
See step 2 on page 13.
Enter your weight if desired.
If you have not entered your weight, see HOW TO
ENTER USER INFORMATION on page 12.
During the program, the speed and incline settings
for the current period can be adjusted with the
SPEED and INCLINE buttons. Adjustments will
not be stored in memory. To reprogram speed
and incline settings, press the LEARN button. The
LEARN indicator will light. Speed and incline set-
tings can be reprogrammed only when the in-
dicator is lit. Next, adjust the speed and incline of
the treadmill with the SPEED and INCLINE but-
tons. When the current period of the program is
completed, the new speed and incline settings will
be stored in memory. When you have repro-
grammed speed and incline settings for as many
periods as desired, press the LEARN button
again.
Select custom program 1 or 2.
4
When the key is inserted,
the manual mode will be
selected. To select a
custom program, press
the MODE button repeat-
edly until the custom 1 or
2 indicator lights.
Press the START button or the SPEED + but-
ton to start the program.
5
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
To stop the program temporarily, press the STOP
button. The TIME display will begin to flash. To
restart the program, press the START button or
the SPEED + button. To end the program, press
the STOP button, remove the key, and then rein-
sert the key.
Each custom program is divided into one-minute
periods. One speed setting and one incline setting
are programmed for each period. The speed set-
ting for the first
period is
shown in the
Follow your progress with the LED displays.
CURRENT PERIOD
6
7
flashing CUR-
RENT PE-
RIOD column
of the LED
matrix. (The
incline
settings are
not shown in
the matrix.)
See step 7 on page 14.
When the program is completed, remove the
key.
See step 7 on page 16.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CD’s, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
20 and 21 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 22 for connecting instructions. To
use iFIT.com programs directly from our internet
site, the treadmill must be connected to your home
computer. See page 21 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
Audio
Cable
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA Y-adapter. Plug the RCA Y-adapter into the
LINE OUT jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Adapter
Cable
Wire removed from
LINE OUT jack
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV with
a built-in VCR, see instruction B. If your VCR is
connected to your home stereo, see HOW TO CON-
NECT YOUR HOME STEREO on page 21.
To use iFIT.com CD’s or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or VCR.
See HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER on page 20.
Note: To purchase iFIT.com CD’s or videocas-
settes, call toll-free 1-800-735-0768. Follow the steps
below to use an iFIT.com CD or video program.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Insert the key into the console.
1
A
See HOW TO TURN ON THE POWER on page 12.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
AUDIO OUT
Select user 1, 2, or 3.
2
RIGHT
LEFT
See step 2 on page 13.
Audio
Cable
Adapter
Select the iFIT.com mode.
3
When the key is inserted,
the manual mode will be
selected. To use an
iFIT.com CD or video pro-
gram, press the MODE
button repeatedly until the
iFIT.com indicator lights. The letters “I FIT” and one
moving indicator will appear in the LED matrix.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the Y-
adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
Insert the iFIT.com CD or videocassette.
4
If you are using an iFIT.com CD, insert the CD into
your CD player. If you are using an iFIT.com video-
cassette, insert the videocassette into your VCR.
B
ANT IN
.
Press the PLAY button on your CD player or
VCR.
VIDEO AUDIO
IN
RF OUT
CH
3
4
5
OUT
A moment after the button is pressed, your personal
trainer will begin guiding you through your workout.
Simply follow your personal trainer’s instructions.
Note: If the TIME display is flashing, press the START
button or the SPEED + button on the console. The
treadmill will not respond to a CD or video program
when the TIME display is flashing.
RCA Y-adapter
Adapter
Audio
Cable
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic “chirp-
ing” sound will alert you when the speed and/or in-
cline of the treadmill is about to change. CAUTION:
Always listen for the “chirp” and be prepared for
speed and/or incline changes. In some in-
stances, the speed and/or incline may change
before the personal trainer describes the
change.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the SPEED or INCLINE buttons
on the console. However, when the next “chirp”
is heard, the speed and/or incline will change
to the next settings of the CD or video program.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
To stop the walking belt at any time, press the
STOP button on the console. The TIME display
will begin to flash. To restart the program, press
the START button or the SPEED + button. After a
moment, the walking belt will begin to move at 1.0
mph. When the next “chirp” is heard, the
speed and incline will change to the next set-
tings of the CD or video program.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
Follow your progress with the LED displays.
6
7
See step 7 on page 14.
When the program is completed, remove the
key.
When the CD or video program is completed, the
walking belt will stop and the TIME display will
begin to flash. Note: To use another CD or video
program, press the STOP button or remove the
key and go to step 1 on page 22.
See step 7 on page 16.
CAUTION: Always remove iFIT.com CD’s and
videocassettes from your CD player or VCR
when you are finished using them.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
• Make sure that the iFIT.com indicator is lit and
that the TIME display is not flashing. If the
TIME display is flashing, press the START
button or the SPEED + button on the console.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow the on-line instructions to start the
program.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR INTERNET SITE
7
8
When you start the program, an on-screen count-
down will begin.
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothing.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 21. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our Web site.
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
Follow the steps below to use a program from our
Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the SPEED or INCLINE buttons
on the console. However, when the next “chirp”
is heard, the speed and/or incline will change
to the next settings of the program.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 12.
Select user 1, 2, or 3.
2
See step 2 on page 13.
To stop the walking belt at any time, press the
STOP button on the console. The TIME display
will begin to flash. To restart the program, press
the START button or the SPEED + button. After a
moment, the walking belt will begin to move at 1.0
mph. When the next “chirp” is heard, the
speed and incline will change to the next set-
tings of the program.
Select the iFIT.com mode.
3
When the key is in-
serted, the manual
mode will be selected.
To use an iFIT.com CD
or video program, press
the MODE button re-
When the program is completed, the walking belt
will stop and the TIME display will begin to flash.
Note: To use another program, press the STOP
button and go to step 6.
peatedly until the iFIT.com indicator lights. The
letters “I FIT” and one moving indicator will appear
in the LED matrix.
Go to your computer and start an internet
connection.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the TIME display is not flashing. In addition,
make sure that the audio cable is properly con-
nected, that it is fully plugged in, and that it is
not wrapped around a power cord.
4
Start your web browser, if necessary, and go to
5
Follow the desired links on our internet site to
select a program.
6
Follow your progress with the LED displays.
9
Read and follow the on-line instructions for using a
program.
See step 7 on page 14.
When the program is completed, remove the
key.
10
See step 7 on page 16.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Make sure
that there is not a letter “d”
THE INFORMATION MODE/DEMO MODE
in the CALS/FAT CALS dis-
play. If a “d” appears in the
display, the console is in the
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
“demo” mode. This mode is intended to be used only
when a treadmill is displayed in a store. When the con-
sole is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays and indicators on the console will auto-
matically light in a preset sequence, although the but-
tons on the console will not operate. If a “d” appears in
the CALS/FAT CALS display when the information
mode is selected, press the SPEED – button so the
display is blank.
To select the information mode, hold down the STOP
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown:
To exit the information mode, remove the key from the
console.
The SPEED/PACE display will
show an “E” (for English miles)
or an “M” (for metric kilome-
ters). The unit of measurement
can be changed by pressing
the SPEED + button.
The DISTANCE/LAPS display
will show the total number of
miles that the walking belt has
moved.
The TIME display will show the
total number of hours that the
treadmill has been used.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
2
treadmill firmly. Hold the lock knob with your left hand
and pull it to the side. Raise the treadmill until the lock
knob is aligned with the catch. Slowly release the lock
knob. Make sure that the pin on the lock knob is in-
side of the catch.
Pin
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Lock
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the pin
on the lock knob is inside of the catch.
Book Holder
1. Hold the handrails as shown and place one foot against
the hood only in the location shown. Do not hold or
push on the book holder or it may be damaged.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. Never move the treadmill without tipping it back.
To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not move the treadmill
over an uneven surface.
Base
3. Place one foot on the base and carefully lower the tread-
mill until it is resting on the base.
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Using your left hand,
pull the lock knob to the left and hold it. Pivot the treadmill down until the frame is past the pin on the lock knob.
Note: You may need to push the handrail to the side slightly.
2. See drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not drop
the treadmill CAUTION: To decrease the possibility of injury, bend your legs and keep your back
straight.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
c
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
Tripped
Reset
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the on
position.
d
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill near the power cord (see c. above). If the circuit
breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position (see d. above).
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
3”–4”
Rear Roller Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-
free.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
a
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
b
PROBLEM: The Speed/Minutes-Mile display on the console does not function properly
SOLUTION: a. Remove the key from the console and unplug the
a
power cord. Remove the screws from the hood and
carefully remove the hood. Locate the Reed Switch
(17) and the Magnet (12) on the left side of the Pulley
(11). Turn the Pulley until the Magnet is aligned with
1/8”
11
12
26
the Reed Switch. Make sure that the gap between
the Magnet and the Reed Switch is about 1/8”. If
necessary, loosen the Reed Switch Screw (26) and
move the Reed Switch slightly. Retighten the Screw.
Re-attach the hood and run the treadmill for a few
minutes to check for a correct speed reading.
17
Top
View
PROBLEM: The heart rate monitor does not function properly
SOLUTION: a. If the heart rate monitor does not function properly, refer to HEART
b
RATE MONITOR TROUBLE-SHOOTING on page 7.
b. If the heart rate monitor still does not function properly, the battery
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the “open” position. Remove
the cover.
Next, remove the old battery from the sensor unit. Insert a new CR
2032 battery, making sure that the writing is on top. In addition, make
sure that the rubber gasket is in place in the sensor unit. Replace the
battery cover and turn it to the closed position.
CR2032
Battery
Rubber
Gasket
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: When the heart rate monitor is used, the letters “PLS” appear in the PULSE display or the
displayed heart rate is excessively high or low
SOLUTION: a. See HEART RATE MONITOR TROUBLE-SHOOTING on pages 7 and 8.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
REEBOK UNIVERSITY
Reebok University was launched in 1993 to fulfill a
vision to establish a “university without walls” that
develops quality, researched, state-of-the-art fitness
programming for the fitness industry throughout the
world.
WALKING AND REDUCED RISK FOR CARDIOVAS-
CULAR DISEASE
Several studies have found that regular walking at any
speed can increase HDL-C cholesterol (a high-density
lipoprotein which removes excess cholesterol from the
body) and can lower concentrations of blood triglyc-
erides (a storage form of fat), thus reducing the risk for
Working with the world’s best professionals, Reebok
University has created a host of original programs,
such as Step Reebok®, Walk ReebokSM, Slide ReebokSM cardiovascular disease.
and Reebok City JamSM. The industry has adopted
Reebok programming as the “gold” standard. Our
guidelines and terminology are used by fitness profes-
sionals and participants around the world, and our
exceptional programming has been approved in the
United States by AFAA and ACE for continuing educa-
tion credits.
Duncan and his colleagues3 concluded that exercise
does not have to be vigorous to reduce cardiovascular
risk factors. In other words, people who choose to
stroll rather than walk briskly can reduce their risk for
cardiovascular disease.
After studying the physical activity patterns of 17,000
Harvard alumni over a 20-year period, Paffenbarger
and his colleagues4 concluded that walking as little as
five city blocks per day can reduce the risk of cardio-
vascular disease, and walking 2 miles per day can
reduce the risk of a heart attack by 28% or more.
Therefore, while walking at a fast pace will improve
aerobic fitness, walking at any speed (slow or fast) can
reduce a person's risk for heart disease.
WALKING AND CARDIORESPIRATORY
ENDURANCE
Scientific studies confirm that
walking at a moderate to brisk
pace can enhance aerobic
fitness. Rippe and his
colleagues1 found that
of 500 subjects tested,
67% of the men and
90% of the women were
able to reach their target
heart rates by
WALKING AND WEIGHT REDUCTION
Walking is an excellent activity for burning calories.
The steeper the incline and/or the faster the speed, the
more calories are burned. For example, a 150-pound
person walking at 3.5 miles per hour on flat ground will
burn about 300 calories per hour. This same person
will burn 400 calories per hour on a gentle 4% incline
and 500 calories per hour on a steeper 10% incline. If
this person speeds the pace up to 4 miles per hour on
level ground, 350 calories will be burned in one hour.5
walking 4 to 4.5 miles
per hour.
Pollock and his colleagues2 found that middle-aged
men who walked at a pace of 3.5 to 4.5 miles per hour
for 40 minutes four times per week had the same car-
diovascular improvements as men the same age who
jogged for 30 minutes three times per week. Although
the intensity of exercise was lower for the walkers than
the runners, the increased duration and frequency of
walking provided the walkers with similar aerobic ben-
efits as the runners.
It should be noted that participants who do not wish to
walk at faster speeds can burn a comparable number
of calories by walking for longer periods of time.
WALKING AND BONE DENSITY
Osteoporosis is a major health problem in the United
States, affecting an estimated 15 to 30 million people.
An age-related disorder, osteoporosis reduces the
density of bones. This disease can be life-threatening
since many older people die as a result of complica-
tions suffered from broken bones. Adequate calcium in
the diet and weight-bearing exercises seem to reduce
the risk of osteoporosis.
On the basis of current research, it seems clear that
walking at a moderate to brisk pace can be an excel-
lent aerobic activity.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Several studies have reported that regular walking at
moderate to brisk speeds appears to increase bone
density. Specifically, Fradin and his colleagues6 found
that 70-year-old subjects who walked at least 30 min-
utes per day had higher bone mineral content than
subjects who walked less than 30 minutes per day.
Jones and his colleagues7 reported that sedentary
women (aged 30 to 61 years old) who began a regular
walking program and continued for one year increased
their bone density.
During a 24-week study, not one of 59 participants
who walked five days a week at speeds between 3 and
5 miles per hour sustained a walking-related injury that
necessitated consulting with a physician. Carroll and
his colleagues10 reported that 14% of the elderly sub-
jects participating in a walking study suffered training-
related orthopedic injuries, mostly to the lower leg and
foot. The majority of injuries occurred in the group as-
signed to "fast walking."
It is important to note that all forms of exercise have
some degree of risk associated with the activity.
Generally, the less mechanical stress on the muscu-
loskeletal system, the less risk of becoming injured.
Because of the low-impact nature of walking, the inci-
dence of injury appears to be low when compared to
other high-impact activities.
Since walking can be comfortably performed by people
of any age, walking appears to be practical and effec-
tive in reducing a person's risk for developing osteo-
porosis.
WALKING AND STRESS REDUCTION
There are many stressors in today's society, including
economic concerns, work-related pressures and the
need to balance career goals with home responsibili-
ties. People who are unable to cope with these types
of stressors are often tense and anxious, and may
even become physically or psychologically ill.
REFERENCES
1. Rippe, J., Ross, J., et. al. “Cardiovascular effects of walking.”
(Abstract), Proceedings of the Second International Conference
on Physical Activity, Aging and Sports, July, 1985, p. 47.
2. Pollock, M., Miller, H. Jr., et. al. “Effects of walking on body com-
position and cardiovascular function of middle-aged men.”
Journal of Applied Physiology, 1971, 30:126–130.
3. Duncan, J., Gordon, N., et. al. “Women walking for health and fit-
ness. How much is enough?” Journal of the American Medical
Association, 1991, 266(23):3295–9.
4. Paffenbarger, R., Hyde, R., et.al. “Physical activity, all-cause
mortality and longevity of college alumni.” New England Journal
of Medicine, 1986, 314:605–613.
Researchers have found that exercise is one way to
help people reduce stress. For example, subjects who
engaged in a regular aerobic conditioning program and
who altered their diets experienced significant gains in
self-concept, feelings of well-being and reduced
depression.8
5. “Better walking workouts.” University of California at Berkeley
Wellness Letter, 1992, 8(12):4–5.
6. Fradin, K. Grimby, G., et. al. “Walking habits and health-related
factors in a 70-year-old population,” Gerontology, 1991,
37(5):281–8.
7. Jones, P., Hardman, A., et. al. “Influence of brisk walking on the
broadband ultrasonic attenuation of the calcaneus in previously
sedentary women aged 30–61 years.” Calcified Tissue
International, 1991, 49(2):112–5.
Cramer and his colleagues9 specifically examined the
effect of brisk walking on mildly obese sedentary
women and found that walking improved general psy-
chological well-being. Walking therefore appears to be
an effective tool for improving psychological well-being.
8. Blair, S., Collingwood, T., et. al. “Health Promotion for Educators:
Impact on Health Behaviors, Satisfaction, and General Well-
Being,” American Journal of Public Health, 1984, 74:147–49.
9. Cramer, S., Nieman D., et. al. “The effects of moderate exercise
training on psychological well-being and mood state in women.”
Journal of Psychosomatic Research, 1991, 35(4–5):437–49.
10. Carroll, J., Pollack, M., et. al. “Incidence of injury during moder-
ate and high intensity walking in the elderly.” Journal of
Gerontology, 1992, 47(3):M61–6.
WALKING AND INJURIES
Walking is often associated with a low injury rate.
Walking is considered to be a "low impact" activity be-
cause one foot remains in contact with the ground at
all times. Walking at speeds of 3 miles per hour pro-
duces vertical impact forces that are around 1.25 times
body weight, whereas running at 7 miles per hour in-
creases vertical impact forces to more than 2.5 times
body weight.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
The heart rate monitor is not a medical de-
vice. Various factors, including the user's
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is in-
tended only as an exercise aid in determining
heart rate trends in general.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for pro-
longed periods of time. This increases the demand on
the heart to pump blood to the muscles and on the
lungs to oxygenate the blood. For aerobic exercise, ad-
just the speed or incline of the treadmill until your heart
rate is near the highest number in your training zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exer-
cise—never hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
You can measure your heart rate using the heart rate
monitor. If your heart rate is too high or too low, adjust
the speed or incline of the treadmill accordingly.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may
complete up to five workouts each week if desired.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2. Hamstring Stretch
2
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
5
33
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—MODEL NO. RBTL13910
R0502A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
2
1
1
2
1
2
4
1
1
9
2
2
1
1
1
4
1
20
1
1
1
1
8
4
1
1
3
1
2
1
4
1
1
1
1
1
6
1
2
23
13
1
1
1
2
4
4
Left Foot Rail
Right Foot Rail
Audio Wire
Front Isolator
Latch Catch
Platform
Walking Platform Screw
Walking Belt
Frame Pivot Bolt
Frame Pivot Washer
Front Wheel/Pulley
Magnet
Front Roller Nut/Front Wheel Nut
Spacer Insert
Frame Pivot Spacer
Reed Switch Clip
Reed Switch
51
52
53
54
55
56
57
58
59*
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
2
2
1
1
1
2
1
1
1
1
1
1
1
1
25
1
1
1
1
1
1
3
4
8
2
2
2
1
1
1
1
2
4
1
1
2
2
1
1
1
1
2
1
2
1
5
2
2
1
Heart Rate Strap
Roller Adj. Washer
Rear Roller Adjustment Bolt
Rear Endcap
Frame
Allen Wrench
Rear Platform Screw
Rear Roller
Idler Assembly
Audio Wire Nut
Tension Washer
Foam Grip (left)
Idler Arm
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Idler Spring
Upright
Console Screw
Lock Knob
Lock Knob Sleeve
Lock Knob Spring
Lock Pin Collar
Pin Clip
Lift Frame
Clips
Pulse Receiver Wire
Foot Rail Screw
Motor Belt
Pulse Receiver
Motor
Reading Rack
Screw
Hood Bracket
Ground Wire
Motor Tension Washer
Lift Motor Nut/Pivot Nut
Lift Motor Bolt
Motor Bolt
Outlet Bracket
Plastic Stand-off
Power Supply
Power Supply Bracket
Controller
Controller Bracket
Motor Hood
Hood Screw
Motor Belly Pan
Belt Guide
Screw
Plastic Fastener
Frame Belly Pan
12” Audio Wire
Ground Screw
Rear Foot
Lock Pin
Incline Pivot Bolt/Tension Bolt
Metal Motor Washer
Console Screw (long)
Wheel Spacer
Front Wheel
Wheel Bolt
Pulley Nut
Console Base (Top)
Console
Key/Clip
Right Pad
Belly Pan Screw
Upright Wire Harness
Shock
Upright Endcap
Left Pad
Filter Wire
Latch Warning Decal
Incline Motor
Motor Controller Wire
Incline Motor Spacer
Tie Holder Screw
Tie Holder
Tie
8” Cable Tie
Bumper
Bumper Screw
On/Off Switch
Isolator Washer
Isolator Nut
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118*
1
1
1
2
1
1
1
4
1
1
1
2
2
1
1
1
1
1
Circuit Breaker
Power Cord
Power Cord Grommet
Warning Decal
Heart Rate Sensor
Jack
iFIT.com Audio Cable
Rear Foot Screw
Pulley Washer
Idler Pulley
Pulley Spacer
Outlet Bracket Star Washer
Static Decal
119
120
121
122
123
124
125
126
127
#
2
1
2
1
2
2
1
4
1
1
1
1
1
1
1
Roller Star Washer
Filter Wire
Motor Isolator
Idler Arm Nylon Washer
Base Endcap Screw
Rear Endcap Screw
Incline Motor Bolt (Bottom)
Controller Screw
Motor Isolator Plate
14” White Wire, 2 F
8” Blue Wire, 2 F
#
#
#
#
8” Blue Wire, 2 F
4” Black Wire, 2 F
12” Green Wire, F/Ring
User’s Manual
Audio Wire Nut
Idler Pulley Bolt
Foam Grip (right)
Console Base (bottom)
Latch Assembly
#
* Includes all parts shown in the box
# These parts are not illustrated
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information:
• The MODEL NUMBER of the product (RBTL13910)
• The NAME of the product (REEBOK® V 2000 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on page 34 and this page and the
EXPLODED DRAWING attached in the center of this manual)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire REEBOK® V 2000 (“Product”) is warranted to be free of all defects in material and work-
manship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the frame for a lifetime. The motor for five
years after the date of purchase. The belt and deck are covered for two years after the date of purchase. All mechanical
components are covered for two years after the date of purchase. All electrical components are covered for two years after
the date of purchase. Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or com-
ponent, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized service
provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to use,
operate, and maintain as set out in your User’s Manual (“Manual”).
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of
the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to
do the periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfac-
tion.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-800-999-3756 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary,
arrange for service where your Product is located or advise you how to ship the Product for service. Before shipping, al-
ways obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack your Product
(save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the product. Include a
letter explaining the product or problem and a copy of your proof of purchase if you believe the service is covered by war-
ranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use
or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits,
loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states
do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not
apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or
fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow
limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 183908 R0502A
Printed in USA © 2002 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—MODEL NO. RBTL13910
R0502A
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—MODEL NO. RBTL13910
R0502A
Download from Www.Somanuals.com. All Manuals Search And Download.
|