Model No. RBBE1996.0
Serial No.
USER’S MANUAL
Write the serial number in the
space above for future reference.
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the inversion table.
1. Read all instructions in this manual before
using the inversion table. Use the inversion
table only as described in this manual.
the short knob is fully tightened before you
use the inversion table.
13. Perform all activities on the inversion table in
a slow, controlled manner. Aggressive exer-
cise can cause the inversion table to tip over.
2. It is the responsibility of the owner to ensure
that all users of the inversion table are ade-
quately informed of all precautions.
14. Always exercise with a partner. Your partner
should be ready to return the backrest to the
upright position if you cannot complete the
rotation.
3. The inversion table is intended for home use
only. Do not use the inversion table in any
commercial, rental, or institutional setting.
15. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.
4. Keep the inversion table indoors, away from
moisture and dust. Do not put the inversion
table in a garage or covered patio, or near
water.
16. Following is a list of factors and conditions
that may make inverting inadvisable (this list
is not exhaustive; it is intended only for refer-
ence). If one or more factors or conditions
apply to you, consult your physician before
using the inversion table.
5. Use the inversion table only on a level sur-
face. Cover the floor beneath the inversion
table to protect the floor.
• Pregnancy
• Hiatal hernia or ventral hernia
• Glaucoma, retinal detachment, or conjunc-
tivitis
6. Make sure that all parts are properly tight-
ened each time the inversion table is used.
Replace any worn parts immediately.
• High blood pressure, hypertension, or
recent stroke or transient ischemic attack
• Heart or circulatory disorders for which
you are being treated
• Middle ear infection and extreme obesity
• Spinal injury, cerebral sclerosis, or acutely
swollen joints
7. Keep children under age 12 and pets away
from the inversion table at all times.
8. The inversion table is designed to support a
maximum user weight of 300 lbs. (136 kg).
Do not use weights with the inversion table.
• Bone weakness (osteoporosis), recent
unhealed fractures, medullary pins, or sur-
gically implanted orthopedic supports
• The use of anticoagulants, including high
doses of aspirin
9. Always wear athletic shoes with laces to help
secure your feet in the inversion table, and
for foot protection while exercising.
10. The inversion table should be used only by
persons 6 ft. 6 in. (198 cm) tall or less.
17. The decal shown on page 4 has been placed
on the inversion table. If the decal is missing
or illegible, call the toll-free telephone num-
ber on the front cover of this manual and
order a free replacement decal. Apply the
decal in the location shown.
11. Keep hands and feet away from moving
parts.
12. Always make sure that the ankle lock is
secured snugly against your ankles and that
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile REEBOK®
INVERSION SYSTEM inversion table. The inversion
table will increase your intervertebral dimension,
decrease pressure on intervertebral discs, stretch and
relax your muscles, and temporarily relieve back pain
associated with the listed conditions.
model number is RBBE1996.0. The serial number can
be found on a decal attached to the inversion table
(see the front cover of this manual).
To avoid a registration fee for any service needed
under warranty, you must register the inversion
For your benefit, read this manual carefully before
using the inversion table. If you have questions after Before reading further, please review the drawing
reading this manual, please see the front cover of this below and familiarize yourself with the parts that are
manual. To help us assist you, please note the product labeled.
model number and serial number before calling. The
ASSEMBLED DIMENSIONS:
Height: 62 in. (157 cm)
Width: 36 in. (91 cm)
Headrest
Depth: 66 in. (168 cm)
Handle
Backrest
Right Frame
Long Adjustment Knob
Index Handle
Left Frame
Short Adjustment Knob
Lock Handle
Ankle Brace
Foot Plate
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is
the key number of the part, from the PART LIST on page 18. Note: Some small parts may have been pre-
assembled. If a part is not in the parts bag, check to see if it has been preassembled.
M4 x 30mm
Screw (63)
M6 Washer (62)
M10 x 16mm
Button Screw (54)
M10 x 35mm
Button Bolt (53)
M4 x 15mm
Screw (58)
M10 Washer (68)
M10 x 53mm Button Bolt (78)
M6 x 55mm Button Screw (56)
M8 x 16mm
Button Bolt (61)
M6 x 18mm
Button Screw (55)
M10 Curved Washer (79)
M4 x 20mm
Screw (71)
M10 x 75mm Button Bolt (57)
M10 x 80mm Button Bolt (52)
M5 x 25mm
Screw (59)
M10 Large Washer (64)
M4 x 25mm
Screw (60)
M10 x 85mm Button Bolt (51)
M10 x 95mm Button Bolt (73)
M8 Nylon
Locknut (72)
M10 Nylon
Locknut (65)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Make Assembly Easier
This manual is designed to ensure that the
inversion table can be assembled successfully
by almost anyone. However, the inversion table
has many parts, and the assembly process will
take time. Most people find that if they set aside
plenty of time, assembly goes smoothly.
• As you assemble the inversion table, make sure
that all parts are oriented as shown in the
drawings.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
In addition to the included hex key
and grease packets, the following tools (not
included) may be required for assembly:
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires two persons.
• two adjustable wrenches
• one rubber mallet
• Because of its weight and size, the inversion
table should be assembled in the location where
it will be used. Make sure that there is enough
clearance to walk around the inversion table as
you assemble it.
• one standard screwdriver
• one Phillips screwdriver
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
1.
1
Before beginning assembly, make sure
2
that you understand the information in
the box above. For help identifying
small parts, see page 5.
1
Attach a Foot (42) to the Left Base (1) with an
M4 x 20mm Screw (71). Next, tighten a
Leveling Foot (41) into the Left Base.
Press a 63mm Round Cap (40) onto the Left
Base (1).
42
71
Repeat this step for the Right Base (2).
40
41
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach the Left Base (1) to the Right Base (2)
with two M10 x 80mm Button Bolts (52), four
M10 Curved Washers (79), and two M10
Nylon Locknuts (65).
2
2
79
65
1
42
71
Attach another Foot (42) to the Right Base (2)
with an M4 x 20mm Screw (71).
79
52
3. Attach the Support Leg (13) to the Center
Base (3) with three M10 x 35mm Button Bolts
(53) and three M10 Nylon Locknuts (65).
3
14
Attach the Base Plate (14) to the Center Base
(3) with four M5 x 25mm Screws (59).
13
53
53
3
59
65
59
4. Attach the Support Bracket (15) to the Support
Leg (13) with two M4 x 15mm Screws (58).
4
15
58
13
58
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Attach the Center Base (3) to the Left and
Right Bases (1, 2) with four M10 x 80mm
Button Bolts (52), four M10 Curved Washers
(79), and four M10 Nylon Locknuts (65).
5
52
79
79
2
1
52
79
52
79
3
65
6. See the inset drawing. Identify the Center
6
32
65
Frame (7).
64
48
70
Apply some of the included grease to both
sides of the Left Large Spacer (31).
5
31
7
Attach the Left Large Spacer (31) and the Left
Frame (4) to the Center Frame (7) with an
M10 Nylon Locknut (65), an M10 Large
Washer (64), and a 29mm Spacer (48). Then,
press an 89mm Cap (32) into the Center
Frame.
Grease
4
Repeat this step with the Right Large
Spacer (70) and the Right Frame (5).
7
7. Attach the Left and Right Frames (4, 5) to the
Left and Right Bases (1, 2) with four M10 x
85mm Button Bolts (51) and four M10 Nylon
Locknuts (65).
7
5
65
65
2
4
65
65
1
51
51
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Attach the Top Cover (23) and the Bottom
Cover (24) to the Center Frame (7) with two
M4 x 15mm Screws (58) and an M4 x 30mm
Screw (63).
8
23
58
24
63
7
Attach the Center Frame Extension (6) to the
Center Frame (7) with two M10 x 53mm
Button Bolts (78) and two M10 Nylon Locknuts
(65).
58
78
6
65
9. Orient the Headrest Frame (9) and the
Backrest Frame (8) as shown. Attach the
Headrest Frame to the Backrest Frame with
two M10 x 16mm Button Screws (54).
9
9
54
54
8
10. Apply a small amount of grease to an M10 x
95mm Button Bolt (73).
10
72
8
Pull the Long Adjustment Knob (43) out as far
as it will go. Insert the bracket on the Backrest
Frame (8) into the Top Cover (23). Next, attach
the Backrest Frame to the Center Frame
Extension (6) with the M10 x 95mm Button
Bolt (73) and an M10 Nylon Locknut (65).
Then, engage the Long Adjustment Knob into
one of the holes in the bracket.
61
Bracket
23
8
See the inset drawing. Attach an M8 x 16mm
Button Bolt (61) and an M8 Nylon Locknut (72)
to the hole in the end of the bracket on the
Backrest Frame (8).
43
65
6
73
Grease
9
Download from Www.Somanuals.com. All Manuals Search And Download.
11. See the left inset drawing. Identify the Top
Tube (16), the Bottom Tube (17), and the
Ankle Brace Tube (18); the Tubes have differ-
ent lengths and holes in different positions.
11
Largest holes
must be on top
16
18
17
18
16
Orient the Top Tube (16) and the Bottom
Tube (17) so that the largest holes are on top
(see the right inset drawing), and insert
them into the indicated holes in the Leg
Frame (10). Attach each Tube with an M4 x
15mm Screw (58).
17
10
Orient the Ankle Brace Tube (18) as shown,
and insert it into the Leg Frame (10). Attach
the Ankle Brace Tube with two M4 x 15mm
Screws (58).
Holes
Holes
16
58
Make sure that the M4 x 15mm Screws
(58) are tightened into the holes in the bot-
toms of the Tubes (16, 17, 18).
17
58
58
12
19
12. Set the Foot Plate (19) on the Top Tube (16)
and the Bottom Tube (17). Finger tighten
four M4 x 25mm Screws (60) through the
Tubes into the Foot Plate. Do not tighten the
Screws yet.
16
60
17
60
13. Slide the Lock Frame (11) onto the notched
bracket on the Leg Frame (10), and insert the
lower end of the Lock Frame into the slot in
the Foot Plate (19). Attach the Lock Frame
with an M10 x 75mm Button Bolt (57), two
M10 Washers (68), two 16mm Spacers (46),
and an M10 Nylon Locknut (65) as shown.
Make sure that the Button Bolt is inserted
through the hole in the lower end of the
Lock Frame.
13
33
11
10
Notch
46
Slot
68
19
See step 12. Tighten the four M4 x 25mm
Screws (60).
65
57
61
68 46
Pull the Lock Handle (33) upward and pivot
the Lock Frame (11) over the indicated notch
in the bracket on the Leg Frame (10).
Release the Lock Handle and engage the
Lock Frame into the notch.
72
10
See the inset drawing. Attach an M8 x
16mm Button Bolt (61) and an M8 Nylon
Locknut (72) to the hole in the end of the
bracket on the Leg Frame (10).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Identify the two Rear Ankle Braces (80), which
have holes in the indicated locations.
14
Slide a Rear Ankle Brace (80) onto the Ankle
Brace Tube (18). Attach the Rear Ankle Brace
with two M4 x 15mm Screws (58). Make sure
that the Screws are tightened into the indi-
cated holes in the Ankle Brace Tube. Next,
press a 19mm Round Cap (45) into the Ankle
Brace Tube, and attach the Round Cap with
an M4 x 15mm Screw (58).
80
80
45
58
18
Holes
Attach the other Rear Ankle Brace (80) to
the Ankle Brace Tube (18) in the same way.
Holes
58
15. Slide a Front Ankle Brace (22) onto the round
tube on the Lock Frame (11). Next, press a
19mm Round Cap (45) into the round tube,
and attach the Round Cap with an M4 x 15mm
Screw (58).
15
22
11
22
Attach the other Front Ankle Brace (22) in
the same way.
45
58
16. Pull the Short Adjustment Knob (74) out as far
as it will go, and insert the end of the Leg
Frame (10) a few inches into the Backrest
Frame (8).
16
8
Hole
38
Tab
8
See the inset drawing. Press the round tab
on the Leg Frame Bushing (38), and press the
Leg Frame Bushing upward into the Backrest
Frame (8). Make sure that the round tab is
in the indicated hole in the Backrest Frame.
10
10
74
Holes
Then, slide the Leg Frame (10) farther into the
Backrest Frame (8), and engage the Short
Adjustment Knob (74) into one of the holes in
the Leg Frame.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Attach the Headrest (20) to the Headrest
Frame (9) with two M6 x 18mm Button Screws
(55), an M6 x 55mm Button Screw (56), and
three M6 Washers (62).
17
9
20
62
56
Attach the Backrest (21) to the Backrest
Frame (8) in the same way.
55
62
21
8
18. Attach a Handle (12) to the Left Frame (4) with
two M10 x 80mm Button Bolts (52), two M10
Curved Washers (79), and two M10 Nylon
Locknuts (65).
18
12
Attach the other Handle (12) in the same
way.
12
65
Make sure that all parts are properly tight-
ened before you use the inversion table.
65
4
79
52
WARNING:
HOW TO LOCK THE INVERSION TABLE
FOR STORE DISPLAY OR TO PREVENT
UNSUPERVISED USE
65
13
When the inversion table is displayed in a
store, or when it is not in use, it should be
locked to prevent unsupervised use. First,
insert the threaded end of the Lock Pin (50)
into the Support Leg (13), and position the
other end of the Lock Pin on top of the Leg
Frame (10). Then, tighten an M10 Nylon
Locknut (65) onto the Lock Pin.
50
10
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT
This section explains how to adjust the inversion table. See DEVELOPING A PROGRAM on page 16 for impor-
tant information about how to get the most benefit from the inversion table.
Make sure that all parts are properly tightened each time you use the inversion table. Replace any worn parts
immediately. The inversion table can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use
solvents to clean the inversion table.
SELECTING THE BACKREST FRAME POSITION
Hole A
Hole B
Hole C
Hole D
8
See the inset drawing. The bracket on the Backrest
Frame (8) has four adjustment holes. The correct hole
to use will depend on your body weight and the
desired level of responsiveness. See the chart to
determine which hole to use. For example, if you
weigh between 200 and 250 pounds and you are a
beginning user, the chart recommends that you use
hole A.
8
43
To adjust the Backrest Frame (8), first pull the Long
Adjustment Knob (43) out as far as it will go. Move the
Backrest Frame and engage the Long Adjustment
Knob into the desired hole in the bracket on the
Backrest Frame.
Try the inversion table with the Backrest Frame (8)
adjusted to each position to determine which one is
best for you.
Note: 1 lb. = 2.2 kg
ADJUSTING THE LEG FRAME
The length of the Leg Frame (10) can be adjusted to
correspond to your height. Pull the Short Adjustment
Knob (74) out as far as it will go. Slide the Leg Frame
into or out of the Backrest Frame (8) so that the first
or second measurement greater than your height is
covered by the Backrest Frame. Then, engage the
Short Adjustment Knob into adjustment holes in the
Leg Frame and the Backrest Frame.
Height
Measurements
8
10
74
Adjustment
Hole
Use the inversion table with the Leg Frame (10)
adjusted to a few different lengths to determine which
length is best for you.
WARNING:
The inversion table is
designed to be used by persons 6 ft. 6 in. (198
cm) tall or less.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE ANKLE LOCK
To secure your ankles in the inversion table, pull
the Lock Handle (33) out as far as it will go, and
move the Lock Frame (11) away from the Leg
Frame (10). Stand on the Foot Plate (19), with the
backs of your legs against the Rear Ankle Braces
(80). Then, push the Lock Frame against your
ankles and engage the Lock Handle into a notch in
the Leg Frame.
Notches
10
33
11
80
19
WARNING:
Always make sure
that the Lock Frame (11) is secured snugly
against your ankles before using the inver-
sion table. Always wear athletic shoes with
laces to help secure your feet in the inversion
table.
SETTING THE INVERSION ANGLE
The inversion table can be set to rotate between
15° and 90°, in 15° increments. To set the inver-
sion angle, pull the Index Handle (25) out as far as
it will go, and turn the Index Handle until the arrow
on top of the Index Handle points to the desired
degree setting. Then, release the Index Handle;
make sure that the Index Handle is fully
engaged.
Arrow
25
LEVELING THE INVERSION TABLE
If the inversion table rocks slightly on your floor,
turn one or both of the Leveling Feet (41) until the
inversion table is level.
65
LOCKING THE INVERSION TABLE
13
To lock the inversion table when you are not using
it, insert the threaded end of the Lock Pin (50) into
the Support Leg (13), and position the other end of
the Lock Pin on top of the Leg Frame (10). Then,
tighten an M10 Nylon Locknut (65) onto the Lock
Pin.
50
10
41
41
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ROTATING ON THE INVERSION TABLE
This section explains how to rotate back on the inversion table, and then return to the starting position. Before
using the inversion table, see the ADJUSTMENT section starting on page 13 to correctly set up the
inversion table. It may be helpful to have a second person ready to assist you as you learn to use the inversion
table.
ROTATING BACK ON THE INVERSION TABLE
ROTATING UP ON THE INVERSION TABLE
To rotate back on the inversion table, slowly lift your
arms over your head until you reach the desired posi-
tion. The speed at which you lift your arms will deter-
mine how quickly the inversion table will rotate. Rest
your arms in a comfortable position that does not
To return to the starting position, move your hands
toward your waist until you rotate to a horizontal posi-
tion. Rest in a horizontal position for 30 to 60 seconds
before rotating to the starting position. This will allow
your body to readjust. Return to the starting position
cause the inversion table to rotate. Note: The inversion slowly. Dizziness after using the inversion table is an
table will rotate only to the degree setting set by the
index handle.
indication that you have returned to the starting position
too quickly.
To rotate up from the fully inverted position, pull your-
self up using the handles.
Do not sit up to return to the starting position.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DEVELOPING A PROGRAM
This section contains information and suggestions about using the inversion table. Make sure that all parts are
properly tightened each time you use the inversion table. Replace any worn parts immediately. See the ADJUST-
MENT section starting on page 13 to identify parts referred to in this section.
BENEFITING FROM USING THE INVERSION TABLE INTERMEDIATE PROGRAM
If you feel nauseated while using the inversion table,
return to the starting position. Note that it may take a
few weeks of use for your inner ear to become accus-
tom to being inverted.
The following are suggestions for persons who have
become comfortable using the inversion table as
described under the BEGINNER PROGRAM.
Increase the angle to which the inversion table can
rotate, as it is comfortable. Adjust the index handle to
allow the inversion table to rotate to up to 60°, a few
degrees at a time.
Do not use the inversion table right after you have
eaten.
Moving while using the inversion table may make it a
more comfortable experience, and may help joints and
muscles stretch and relax. Always move in a slow, con-
trolled manner.
Start to do gentle stretching while using the inversion
table.
Gradually increase the amount of time that you use
the inversion table to ten minutes or more, two or
three times a day. Routines can be varied from rotat-
ing back for one or two minutes and then up for 30
seconds, to rotating back and up for equal amounts of
time.
The greater the angle at which the inversion table is
used, the shorter the time that you should rotate back
before rotating up. Increase the amount of inverted time
and the angle of use gradually.
Always pay attention to how your body feels as you use
the inversion table. Increase the level of intensity only
as it is comfortable for you. When you feel like you have
had enough, return to the starting position.
FULL INVERSION PROGRAM
The following are suggestions for persons who have
become comfortable using the inversion table as
described under the INTERMEDIATE PROGRAM and
desire to rotate to greater angles. Note that all the
BEGINNER PROGRAM
The following are suggestions for persons who are just benefits of inversion can be gained by rotating to 60°.
starting to use the inversion table.
Do not attempt to do sit-ups.
Set the index handle to allow the backrest frame to
Increase the angle to which the inversion table can
rotate to 15° or less for the first one or two weeks. This rotate, as it is comfortable. Adjust the index handle to
will allow your body time to adjust to the change in
gravitational pull.
allow the inversion table to rotate until it comes in con-
tact with the center frame.
Use the inversion table for one or two minutes at a
time, two or three times a day.
Adjust the backrest frame so that the long adjustment
knob is in the top hole (see SELECTING THE BACK-
REST FRAME POSITION on page 13). If you weigh
Stay inverted only for as long as it is comfortable. This 220 lbs. (100 kg) or more, adjust the long adjustment
may be only a few seconds at first.
knob to the center hole in the backrest frame. Rotate
back and up as described on page 15.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. RBBE1996.0
R0107A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
2
2
2
3
Left Base
Right Base
Center Base
Left Frame
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
#
1
2
4
2
2
2
1
1
4
10
3
2
4
2
1
20
4
4
2
7
1
2
24
1
1
2
1
1
3
2
1
1
1
2
1
2
12
2
-
Long Adjustment Knob
32mm Round Cap
19mm Round Cap
16mm Spacer
Pivot Bushing
29mm Spacer
Bumper
Lock Pin
M10 x 85mm Button Bolt
M10 x 80mm Button Bolt
M10 x 35mm Button Bolt
M10 x 16mm Button Screw
M6 x 18mm Button Screw
M6 x 55mm Button Screw
M10 x 75mm Button Bolt
M4 x 15mm Screw
M5 x 25mm Screw
M4 x 25mm Screw
M8 x 16mm Button Bolt
M6 Washer
M4 x 30mm Screw
M10 Large Washer
M10 Nylon Locknut
M6 x 15mm Screw
M10 Nut
Right Frame
Center Frame Extension
Center Frame
Backrest Frame
Headrest Frame
Leg Frame
Lock Frame
Handle
Support Leg
Base Plate
Support Bracket
Top Tube
Bottom Tube
Ankle Brace Tube
Foot Plate
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Headrest
Backrest
Front Ankle Brace
Top Cover
Bottom Cover
Index Handle
Index Ring
Cup Washer
Small Spring
Cup Bushing
Index Cup
Left Large Spacer
89mm Cap
Lock Handle
Stop Cap
Lock Rod
Lock Spring
Lock Wedge
Leg Frame Bushing
42mm x 70mm Cap
63mm Round Cap
Leveling Foot
Foot
M10 Washer
30mm x 60mm Cap
Right Large Spacer
M4 x 20mm Screw
M8 Nylon Locknut
M10 x 95mm Button Bolt
Short Adjustment Knob
M6 x 60mm Button Bolt
M5 x 15mm Screw
M6 Nut
M10 x 53mm Button Bolt
M10 Curved Washer
Rear Ankle Brace
User’s Manual
#
#
-
-
Hex Key
Grease Packet
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. RBBE1996.0
R0107A
39
69
33
34
20
58
35
80
58
58
18
62
56
55
10
9
45
58
36
67
37
62
54
54
72
58
21
61
58
11
58
80
17
58
58
45
22
19
62
55
56
61
58
45
58
46
72
65
68
58
16
22
58
12
45
68
65
57
62
8
60
44
65
73
70
32
58
23
38
7
75
24
49
74
63
58
65
47
12
44
79
52
48
64
65
43
65
5
47
32
31
78
65
76
65
77
32
65
30
65
64
65
6
39
29
48
28
27
25
66
26
79
52
76
2
42
71
4
62
42
79
41
71
52
65
79
51
65
65
15
65
40
3
79
52
14
65
58
13
65
59
1
58
50
42
71
65
53
52
79
51
59
52
79
40
41
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information:
• the MODEL NUMBER of the product (RBBE1996.0)
• the NAME of the product (REEBOK INVERSION SYSTEM inversion table)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and the EXPLODED DRAWING on
pages 18 and 19)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be pre-authorized by ICON. If the product is shipped to a service center,
freight charges to and from the service center will be the customer’s responsibility. For in-home service, the
customer will be responsible for a minimal trip charge. This warranty does not extend to any product or dam-
age to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center; products used for commercial or rental purposes;
or products used as store display models. No other warranty beyond that specifically set forth above is author-
ized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or conse-
quential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 244688 R0107A
Printed in China © 2007 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|