Ready Remote Remote Starter 24927 User Guide

Model 24927

_➤Owner’s/Installation Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

OR IN CONNECTION WITH THE INSTALLATION, USE, IMPROPER USE, OR

INABILITY TO USE, THE PRODUCT, EVEN IF THE PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO

NOT ALLOW THE EXCLUSION OF LIMITATION OF INCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION

MAY NOT APPLY TO YOU. THE CONSUMER AGREES AND CONSENTS THAT

ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL BE

RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO

COUNTY, CALIFORNIA.

IMPORTANT NOTE:

This product warranty is automatically void if its date code or serial number is defaced,

missing, or altered.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

➤ Date of purchase

➤ Authorized dealer's company name and address

➤ Item number

Download from Www.Somanuals.com. All Manuals Search And Download.

table of contents

limited lifetime consumer warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

Install Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

what is included. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

installation tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Wiring Quick Reference Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

H1 Harness - 6 pin connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

H2 Harness - 8 pin connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

H3 harness - 3 pin connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

relay heavy gauge wires. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 1, Heavy Gauge Wire Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 2, H1, Main Harness Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Step 3, H3 Door Lock Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Step 4, H2 Harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Step 5, Mounting the Receiver/Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Step 6, Immobilizer Bypass Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Step 7, Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

System Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Remote Start Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Testing the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Owner’s Guide . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Transmitter Button Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Remote Start Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Alarm and Security Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Convenience Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 74

quick reference guide: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Download from Www.Somanuals.com. All Manuals Search And Download.

Install Guide

what is included

Control Module

6-Pin Main H1 Harness

8-Pin H2 Secondary Harness

Heavy Gauge Wires

Antenna and cable

Two 5-button remotes

Crash code card

3-pin Keyless Entry harness

Combination Momentary Switch and LED

Hood Pin Switch

Hardware Kit

DVD—Do-It-Yourself Installation Video

Additional parts may be required (such as relays or bypass).

installation tools

Digital Multi-Meter

Drill

Drill Bit (for hood pin switch)

Screwdrivers (Phillips and Flathead)

Wire Stripper

Solder Iron

Electrical Tape

Pliers

Crimping Tool

note: The installation tools listed above may be

optional and those required will vary depending on

your vehicle.

Download from Www.Somanuals.com. All Manuals Search And Download.

important information

Congratulations on the purchase of your remote start keyless entry

system. This system will allow convenient access to your vehicle

with the push of a button, as well as remote start and other

optional features. Properly installed, this system will provide years

of trouble-free operation.

Please take the time to carefully read this User’s Guide in its

entirety and watch the READY REMOTE Do-It-Yourself

Installation Video (DVD) prior to installing your system.

You can print additional or replacement copies of this manual

by accessing the Directed web site at www.readyremote.com.

important! If you are not comfortable working with

electronics or unfamiliar with the tools required,

please contact your local dealer for advice or ask to

have the remote start professionally installed to avoid

costly damages. Failure to properly install the remote

starter may result in property damage, personal injury,

or both.

system maintenance

➜

The system requires no specific maintenance. Your transmitter

is powered by a miniature 12-volt battery (type 23A) that will

last approximately one year under normal use. When the

battery begins to weaken, the operating range will be

reduced.

Download from Www.Somanuals.com. All Manuals Search And Download.

fcc/id notice

➜

This device complies with Part 15 of FCC rules. Operation is

subject to the following conditions: (1) This device may not

cause harmful interference, and (2) This device must accept

any interference received, including interference that may

cause undesirable operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate this device.

warning! safety first

The following safety warnings must be observed at all times:

When properly installed, this system can start the vehicle

via a command signal from the remote control trans-

mitter. Therefore, never operate the system in an area

that does not have adequate ventilation. The following

precautions are the sole responsibility of the user;

however, the following recommendations should be made

to all users of this system:

1. Never operate the system in an enclosed or partially

enclosed area without ventilation (such as a garage).

2. When parking in an enclosed or partially enclosed

area or when having the vehicle serviced, the remote

start system must be disabled by placing the system

into Valet Mode.

3. It is the user's sole responsibility to properly handle

and keep out of reach from children all remote

control units to assure that the system does not

unintentionally remote start the vehicle.

4. THE USER MUST INSTALL A CARBON MONOXIDE

DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT

Download from Www.Somanuals.com. All Manuals Search And Download.

TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT

LIVING AREAS TO THE ENCLOSED OR PARTIALLY

ENCLOSED VEHICLE STORAGE AREA MUST AT ALL TIMES

REMAIN CLOSED.

Use of this product in a manner contrary to its intended

mode of operation may result in property damage, personal

injury, or death. Except when performing the Safety Check

outlined in this user’s guide, (1) Never remotely start the

vehicle with the vehicle in gear, and (2) Never remotely

start the vehicle with the keys in the ignition.

After the remote start module has been installed, test the

remote start module in accordance with the Safety Check

outlined in this installation guide. If the vehicle starts

when performing the Neutral Safety Shutdown Circuit test,

the remote start unit has not been properly installed. The

remote start module must be removed or properly rein-

stalled so that the vehicle does not start in gear. OPERA-

TION OF THE REMOTE START MODULE IF THE VEHICLE

STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF

OPERATION. OPERATING THE REMOTE START SYSTEM UNDER

THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR

PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE

UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE

START MODULE. DIRECTED WILL NOT BE HELD RESPON-

SIBLE OR PAY FOR INSTALLATION OR REINSTALLATION

COSTS.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wiring Quick Reference Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

H1 Harness - 6 pin connector

___ _YELLOW

(+/-) parking light output

(-) factory disarm output

H1/1

___ _BROWN/WHITE

H1/2

___ _VIOLET

(-) hood pin shutdown input

(+) brake switch shutdown input

(-) 400mA status output

H1/3

___ _ORANGE

H1/4

___ _WHITE/BLACK

H1/5

___ _RED/WHITE

H1/6

(-) remote start activation input

Pin #

H1/1

Color

Note

Selectable positive or negative parking light output

Yellow

H1/2

Use this wire if the vehicle is equipped with a

factory alarm. Connect to disarm wire listed on your

sheet.

Brown/White

H1/3

H1/4

Connect this wire to supplied hood pin switch

Violet

Connect this to wire in vehicle that shows 12 volts

when brake is pressed

Orange

H1/5

H1/6

Provides a ground during remote start. This wire is

normally connected to a bypass module if your

vehicle needs one.

This wire will start the vehicle when it sees two

negative pulses. Only used when incorporating into

existing alarm or for testing purposes.

White/Black

Red/White

Download from Www.Somanuals.com. All Manuals Search And Download.

H2 Harness - 8 pin connector

___ _GREEN

Tachometer input

(-) 400mA horn/siren output

(-) wait-to-start input

H2/1

___ _BLUE

H2/2

___ _RED/BLACK

H2/3

___ _YELLOW/GREEN

(+) ignition output

H2/4

___ _GREEN/WHITE

(-) 400mA trunk release output

(-) 400mA RAP, Domelight, Starter Kill

(-) 400mA headlight output

H2/5

___ _BROWN

H2/6

___ _YELLOW/BROWN

H2/7

___ _GRAY/BLACK

H2/8

(-) door trigger input

Pin #

H2/1

Color

Note

Use this wire if the vehicle fails to start correctly in

voltage mode

Green

H2/2

H2/3

Negative output to horn or siren circuit. If your horn is

positive, use a relay.

Blue

Used on diesel engines only. Connects to wait-to-start

wire

Red/Black

H2/4

H2/5

H2/6

Ignition output. Connect this wire to the ignition input

of an aftermarket alarm system.

Yellow/Green

Green/White

Brown

Trunk release wire. Connect this wire to trunk release

wire listed on your vehicle specific printout.

Retained accessory shutdown or factory rearm output.

Connect this wire to factory arm wire if equiped or to

door trigger wire if your vehicle’s accessories stay on

after remote start finishes cycle.

H2/7

H2/8

Headlight output. Connect this wire to headlight wire

in car. If headlights are positive, a relay is required.

Yellow/Brown

Gray/Black

Door trigger input. This wire connects to the door trig-

ger wire in your car to set off alarm when system is

armed and door is opened.

Download from Www.Somanuals.com. All Manuals Search And Download.

H3 harness - 3 pin connector

___ _YELLOW/RED

(-) lock/(+) unlock

(-) unlock/(+) lock

H3/1

___ _EMPTY

H3/2

___ _WHITE/RED

H3/3

relay heavy gauge wires

___ _GREEN

(+) Ign2 or Acc2 output

(+) 12 volt input

___ _PINK

___ _BLUE

(+) ignition 1 output

(+) accessory output

(+) 12 volt input

___ _WHITE

___ _PINK

___ _YELLOW

(+) starter output

BLACK

(-) ground

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Overview

Be sure to read this section thoroughly and view the Do-It-

Yourself Installation DVD video in its entirety before starting the

installation. Pay special attention to all warnings to prevent per-

sonal injury or damage to your vehicle.

Visit our 24-hour technical web site (www.readyremote.com) to

get a vehicle-specific wiring guide prior to starting this installa-

tion.

Have your crash code number handy when contacting tech support

or visiting the web site. During the installation if you are unable

to find answers to your questions on the web site, call 1-800-477-

1382 for live technical assistance. Please note that live technical

support is available Monday-Friday 6am-6pm PST, and Saturday-

Sunday 7am-3:30pm PST.

WARNING!

➤

Verify that the transmission is set to park and that

the parking brake is set before beginning installation.

➤

On vehicles with air bags or supplemental restraint

systems (SRS) you may notice a bright yellow tube

with small wires in it marked SRS underneath the

steering column near the key cylinder. DO NOT tamper

or unplug these for any reason to prevent costly dam-

ages to your vehicle or personal injury. Tampering

may cause unintended deployment of airbags.

➤

This system is intended for automatic, fuel-injected

vehicles only. Installation in any other vehicle is con-

trary to its intended use.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 1, Heavy Gauge Wire Connections

Ground Wire

The BLACK wire connects to the pin next to the light flash jumper

fuse. First strip back a ¾-inch section of the insulation off the

BLACK wire and crimp a ring terminal (not provided) to that wire.

Locate a clean, paint-free metal surface in the drivers kick panel

(do not ground on dash). Using a self-tapping screw, drill the

screw with the ring terminal to the kick panel. Once screwed down,

pull on the wire to ensure a good connection.

SELF-TAPPING

BOLT OR SCREW

GROUND

WIRE

RING

TERMINAL

NOTE: REMOVE ANY PAINT

BELOW RING CONNECTOR

DIA-591

Constant Power and Ignition wires

Almost all your power and ignition wires can be found behind the

key cylinder under the lower driver's side dash panel. Using the

appropriate hand tools, remove the lower dash panel taking care

not to break any parts. If the panel does not come off easily, check

for any additional screws you may have missed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Once the lower dash panel has been removed, locate the ignition

harness at the back of the key cylinder. This is usually a group of

heavy gauge wires (approximate 14ga.).

Place the black lead of the LED tester to a clean metal surface in

the kick panel area and secure it. Probe one of the thicker gauge

wires. The ignition wire colors of your specific vehicle can be

obtained at www.readyremote.com.

note! More problems are attributed to poor ground

connections than any other cause. Take extra care

to ensure the ground is a clean metal-to-metal

contact and secure.

Testing for Constant Power Wires

WARNING! Before making any connection to constant

battery power make sure that the two 30 amp fuses

are removed from the fuse holders on the two pink 12

VOLT wires. Failure to do so may cause fire or short-

ing of sensitive electrical components.

Download from Www.Somanuals.com. All Manuals Search And Download.

With the key in the off position, test the suspect wire. The

constant power wire will read 12V on the multimeter. Once the

constant power wire has been identified, solder the two heavy

gauge 12 VOLT wires (PINK) from the control module to it and

wrap the connection with electrical tape.

note! If the vehicle has more than one constant

power wire, utilize two of them. Connect one of the

heavy gauge PINK wires to one of the constant

power wires and the other heavy gauge PINK wire to

the other constant power wire.

Testing for Ignition Wires

With the multimeter lead still connected in the kick panel, locate

the suspected ignition wire. It will test differently than constant

12 volts. Place the red lead of the multimeter on the suspected

wire. With the key in the off position the multimeter will read 0.

Turn the key to the on position and the multimeter will read 12

volts. Now, watching your multimeter, turn the key to the crank

position. If the 12 volts stays on, then you have found your igni-

tion wire. If the wire tests correctly, solder the BLUE heavy gauge

wire to it and wrap the connection with electrical tape.

If the vehicle requires more than one ignition as per the web site

information, follow the same test procedure and solder the GREEN

heavy gauge wire to it then wrap the connection with electrical

tape. If your vehicle has only one ignition wire, secure the GREEN

wire and dress it out of the way.

Download from Www.Somanuals.com. All Manuals Search And Download.

If your vehicle requires more than two ignitions, an additional

relay (not provided) is required. Refer to the diagram below.

+12 VDC CONSTANT (FUSED 20A)

IGNITION RELAY

(NOT PROVIDED)

TO 2 IGNITION

GROUND

87A

TO 2 IGNITION

+12 VDC CONSTANT (FUSED 20A)

IGNITION RELAY

(NOT PROVIDED)

GREEN (+) OUTPUT

TO 2 IGNITION

GROUND

87A

TO 3 IGNITION

Download from Www.Somanuals.com. All Manuals Search And Download.

Accessory and Starter wires

The starter and accessory wires will be located in the same harness

as the ignition and constant power.

To find the accessory wire leave the multimeter’s black lead

connected to ground. Take the red lead and probe the wire

suspected to be the accessory wire. With the key off, your multi-

meter should read 0 volts. Turn the key to the on position the

multimeter should read 12 volts. Now turn the key to the crank

position. If you have the correct accessory wire the multimeter

will read 0 volts while the starter is cranking and 12 volts once

the key returns to the on position. If the wire tests correctly, strip

some insulation off and solder the WHITE heavy gauge wire and

wrap it with electrical tape.

If your vehicle requires more than one accessory then the GREEN

ign2 wire can be programmed to function as an accessory output.

Download from Www.Somanuals.com. All Manuals Search And Download.

If the GREEN wire is being used for ign2 an additional relay (not

provided) is required for a 2nd accessory. Refer to the diagram

below.

+12 VDC CONSTANT (FUSED 20A)

ACCESSORY RELAY

(NOT PROVIDED)

TO ACCESSORY

GROUND

87A

TO ACCESSORY

+12 VDC CONSTANT (FUSED 20A)

ACCESSORY RELAY

(NOT PROVIDED)

WHITE (+) 30A OUTPUT TO

ACCESSORY CIRCUIT

GROUND

87A

TO 2 ACCESSORY

Now that the accessories have been located, find the suspected

starter wire according to the web information. Leave the black

lead of your tester on ground and place the red lead of your multi-

meter on this wire. The multimeter should read 0 volts in all key

positions except the crank position. In the crank position your

multimeter should read 12 volts, and will go to 0 volts when the

starter disengages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Many Nissan and late-model Chrysler vehicles have two starter

wires. A relay and/or resistor (not provided) is required to hook up

the additional starter wire. Refer to the diagram below.

+12 VDC CONSTANT (FUSED 20A)

STARTER RELAY

(NOT PROVIDED)

TO STARTER

GROUND

87A

TO STARTER

+12 VDC CONSTANT (FUSED 20A)

STARTER RELAY

(NOT PROVIDED)

YELLOW (+) OUTPUT

TO STARTER

GROUND

87A

TO 2 STARTER

note! Always check the Web site information

on your vehicle for warnings regarding the

starter wire and check engine lights. Some

vehicles will trip a check engine light if the

starter wire is cut.

Once you locate the starter wire, cut the wire in half (check the

web information before cutting) and try to start the vehicle. If

the vehicle does not start, the correct wire has been identified.

Reconnect both ends of the starter wire while soldering the thick

YELLOW (6) wire of the heavy guage wires to it and wrap the

connection with electrical tape.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 2, H1, Main Harness Connections

Factory Alarm Disarm

Since many newer vehicles come equipped with a factory alarm it

is necessary to disarm it when unlocking the doors or during

remote start. Do not mistake a factory alarm with an immobilizer

system. They each require different disarm operations.

Locate the factory alarm disarm wire using the web site informa-

tion. Once the suspect wire is located, place the multi-meter's red

lead to a (+)12 volt constant source and secure it. Put the multi-

meter in the DC position then probe the suspect wire with the

black lead of your meter. While probing the wire, place the key in

the driver's door cylinder. Turn it to the unlock position and hold

it when testing for the disarm wire. The multimeter should read

12V and will go back to 0V when the key is released.

When the correct wire has been found, solder the BROWN/WHITE

wire of the 6-pin harness to the wire that you determined to be

the factory alarm disarm wire. After this wire has been connected

wrap the connection with electrical tape.

note! On some vehicles the Factory Alarm Disarm

wire is connected to a Body Control Module or a Door

Module. If you find this configuration, please call

Technical Support at 1-800-477-1382.

note! Some vehicles use a + trigger factory alarm

system. Use the website to determine if your vehicle

has a + trigger. If your vehicle has such a system call

1-800-477-1382 for live technical assistance as spe-

cial wiring and an additional relay is required.

Download from Www.Somanuals.com. All Manuals Search And Download.

Parking light flash

There are several different types of parking light circuits. The

following description is for a standard positive-triggered parking-

light circuit, only. If the web vehicle information suggests a (-)

parking light circuit, the fuse jumper (on the side of the module)

must be moved to the opposite position.

The default position for this jumper is for a positive parking light

circuit.

Using the web information on the vehicle, locate the suspected

wire. Connect the black multimeter lead to ground in the kick

panel. Probe the suspected wire with the red lead of your meter.

With the switch in the off position the multimeter should read 0

volts. While watching the multimeter, turn your headlight switch

to the parking light position. The multimeter should read 12 volts.

While testing the suspected wire, run the dash dimmer light

control up and down-the voltage should NOT vary. If the voltage

does vary then this is the wrong wire. Continue probing to find the

correct wire.

Once you have identified the correct wire, solder the small YELLOW

wire of the 6-pin harness to it and wrap the connection with elec-

trical tape.

important! Remember this description is for a (+)

parking light circuit. A (-) circuit will test differently.

Also, if the web information requires using resistors

for parking lights, contact Technical Support.

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Shutdown Wires

With all ignition wires properly connected, find the appropriate

safety shutdown wires. These are the brake wire and hood pin

wires.

WARNING! These wires are meant to protect the

vehicle and anyone near the vehicle. They MUST

be connected to prevent damage to the vehicle

and possible bodily injury.

First locate the factory brake wire using your multimeter. Find the

switch at the top of the metal arm coming off the brake pedal. Use

your vehicle specific wiring information to determine the color of

this wire. With the black lead of your multimeter still in the kick

panel, probe the suspected wire with the red lead of your multi-

meter. With the brake pedal at rest the multimeter should read 0

volts. While watching the multimeter, depress the brake pedal.

The multimeter should read 12 volts. Once you have located the

correct brake wire, solder the small ORANGE wire in the 6-pin

harness to it and wrap the connection with electrical tape.

WARNING! Do not use the vehicle until you

confirm the operation of the brake shutdown.

Installing the hood pin switch requires drilling a hole in a metal

lip under the hood. Choose a location that will allow the pin

switch to be completely depressed when the hood is closed. The

pin switch has a spade connector on the bottom for the wire

connection.

Crimp your spade connector to the hood pin wire and run the wire

into the vehicle's passenger compartment through a factory rubber

grommet (at the same time you might want to run Tachometer

Input wire and Horn output wire from Optional Harness through

the fire wall as you may need to connect them using the following

steps).

Download from Www.Somanuals.com. All Manuals Search And Download.

Using a sharp, pointed object poke a hole into the grommet

(being careful not to damage any existing wires in the grommet)

and attach the wire to the object with electrical tape. Pull the

wire through the grommet taking extra care to keep the wire away

from any moving parts or anything that will generate extreme

heat.

An alternative to this method would be to find a spot on the fire-

wall with sufficient clearance on both sides and drill an access

hole through the firewall. Take note of what is directly on the

other side of where you are drilling as to not puncture brake cylin-

ders, computers, etc. Once the wire is run into the vehicle and

secured from any moving parts, solder the wire to the VIOLET wire

of the 6-pin harness and wrap the connection with electrical tape.

WARNING! This wire MUST be connected. Do not

use the vehicle until you confirm the operation

of the hood pin shutdown. Improper operation

could result injury or death.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 3, H3 Door Lock Connections

There are 8 different types of door lock systems (Type A - H).

Refer to the vehicle-specific wiring instructions on the web and

the chart below to help determine which door lock system your

vehicle uses. On some late model GM vehicles a door lock data

interface module may be required.

Type A: Three-wire (+) pulse controlling factory lock relays.

Type B: Three-wire (-) pulse controlling factory lock relays.

note! From the factory, your system is set up for Type

B (-) door locks. To change your door lock outputs to

Type A (+), simply use the wires in the oposite con-

figuration. You will now have (+) door locks.

Type C: Direct-wired reversing-polarity switches. The switches are

wired directly to the motors. This type of system has no factory

relays. Relays (not included) will be required for this type of door

lock system.

Type D: Adding one or more aftermarket actuators. These include

slave systems without an actuator in the driver's door, but with

factory actuators in all the other doors.

Type E: Electrically-activated vacuum systems.

Type F: One-wire system - cut to lock, ground to unlock.

This is a vary rare system found only mainly in early 90's imports

Type G: Positive (+) multiplex. One wire controls lock and unlock

using resistor(s).

Type H: Negative (-) multiplex. Same as type G system, but uses

(-) pulse instead.

Download from Www.Somanuals.com. All Manuals Search And Download.

All other door lock systems will require additional relays and/or

resistors. A Directed Electronics 451M Doorlock module can be

used for these other applications. The 451M also includes

diagrams and resistors required for most applications.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 4, H2 Harness

Engine Monitoring Explained

During remote start the system will need to know if the engine is

running. The module does this by monitoring the voltage of the

vehicle's electrical system (or the tachometer-see next section).

Voltage Monitoring

note! If the system has been programmed for

Tachometer monitoring previously, it must be

reprogrammed to Voltage monitoring.

Vehicle electrical systems usually rest at about 12.6 volts when

the engine is not running. This system is programmed to detect

the rise in battery voltage that occurs when the charging circuit

activates after starting, and keep the engine running if the rise is

adequate. It will make up to three start attempts before discon-

tinuing due to an inadequate voltage rise.

Some vehicles have alternators that do not activate immediately

or do not increase voltage sufficiently after starting, this system

will compensate by delaying the time before reading the battery

voltage on the second and third start attempts. This delay will

allow most alternators to activate so the remote start will

continue to run.

The voltage read times are:

First attempt: 10 seconds

Second attempt: 20 seconds

Third attempt: 50 seconds

After the third start attempt, if the voltage increase is still not

adequate to keep the engine running, the Tachometer input

option should be used to monitor the engine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Tachometer Wire

WARNING! In the following procedure DO NOT use

a test light. Use of this type of tester can cause

grounding of sensitive electrical components caus-

ing damage, including damage to the power train

control module. A digital multi-meter is required to

test for this wire.

Do not wear loose clothing that could get entangled

in rotating engine components. Ensure that your

hands and arms are well clear of these rotating

components when working in the engine compart-

ment. Lastly, ensure that all wires and tools are

clear of falling into or entanglement with these

rotating components.

Identify the suspected tach wire according to the web informa-

tion. Next, place the black lead of a MULTI-METER on the nega-

tive battery post and secure it. Put the multi-meter in the AC posi-

tion and connect the probe to the suspect wire with the red lead

of the multi-meter. Then start the vehicle with the key. With the

engine at idle the multi-meter should read between .50 volts to 6

volts, and should fluctuate when you rev the engine.

Have a second person press the gas pedal to increase the RPMs

and watch the meter display. When the RPMs increase the voltage

should rise slightly (not all tachometer outputs will rise when

engine RPM increases). Once the correct tachometer wire has been

identified, turn the vehicle off.

Run the GREEN wire from the 8-pin harness through the firewall

into the engine compartment along side the hood pin wire. Use

the same procedure as with the hood pin wire and pull the wire

through the grommet taking extra care to keep it away from any

moving parts or anything that will generate extreme heat. Once

the wire is run into the engine compartment, strip a small portion

Download from Www.Somanuals.com. All Manuals Search And Download.

of insulation off the tachometer wire in the vehicle and solder the

green tachometer input wire to it. Then wrap the connection with

electrical tape.

note! If using a tach signal, the tach signal MUST

be learned before using the remote starter.

LEARNING YOUR TACH SIGNAL

If using a tach wire, you must learn the tach signal after

completing the installation.

To learn tach signal:

1. Start car with key

2. Wait about 5 seconds for the engine to idle down

3. Press and hold the Momentary switch (about 10

seconds)

4. Tach learned: After a few seconds the LED will flash 2

times and turn on. Continue to hold the switch for 2 - 3

seconds and release.

5. Tach not learned: The LED will not turn on and will flash

3 times when the momentary switch is released. Check

the connections and try again.

Download from Www.Somanuals.com. All Manuals Search And Download.

Following is a brief description of the remainder of the wires in

the H2 harness. For specific details on connecting these outputs

contact Technical Support at 1-800-477-1382.

Horn/siren wire

The Blue wire provides an output for activating the vehicle horn

circuit or an external siren. The output is programmable in Feature

Menu 1/9 for the desired use.

important! This is a low current output and that

requires an external relay when connected to circuits

that draw more than 400mA in current.

Wait-to-start wire

The Red/Black wire is for use with diesel engines that require a

short delay for the glow plugs to warm up before cranking the

engine. Connect this wire to the wire in the vehicle that sends the

signal to turn on the WAIT-TO-START bulb in the dashboard. In

most diesels the wire is negative (ground turns on the bulb) and

the Red/Black wire can be directly connected. If the vehicle uses

a positive wire (12V to turn on the bulb) a relay must be used to

change the polarity.

Ignition Output wire

The Yellow/Green wire should be the ONLY the ignition input to an

existing aftermarket alarm system. This wire will prevent the host

system from sensing that the ignition is on during remote start

operation.

Trunk Release wire

The Green/White wire can be used to activate a vehicle trunk

release solenoid or to operate optional modules that require a

negative input. Whenever the

button is pressed for a few

seconds the system will disarm/unlock and then activate this

Download from Www.Somanuals.com. All Manuals Search And Download.

output. The output will then remain on until the transmitter

button is released.

important! this is a low current output and that

requires an external relay when connected to cir-

cuits that draw more than 400mA in current.

Retained Accessory, Dome Light or Starter Kill wire

The Brown wire has three optional uses depending on the vehicle

application and user preference. The three available operations are

programmable in Feature Menu 2/11

➤

RAP or Retained Accessory Power: This option is

designed to turn off accessories that remain on after the

ignition is turned off. It will pulse 10 seconds after the

remote start status output ceases. It will make the vehi-

cle body control module think the door has opened, thus

turning the accessories off.

➤

Dome Light Supervision: This option will turn on the

dome light for 25 second each time the vehicle is

unlocked. It will cease if on when the doors are locked

or the ignition in turned on.

Start Kill/Anti-grind: This option activates when the

doors are locked to allow for starter kill for the alarm

system and also works as an anti-grind when the remote

start is active.

important! this is a low current output and that

requires an external relay when connected to cir-

cuits that draw more than 400mA in current.

Download from Www.Somanuals.com. All Manuals Search And Download.

Headlight Control wire

The Yellow/Brown wire provides an output for activating the

vehicle headlight circuit. It is controlled by both the ignition

switch and the transmitter. It is programmable in Feature Menu

1/10 for the type of ignition controlled activation.

important! this is a low current output and that

requires an external relay when connected to cir-

cuits that draw more than 400mA in current.

Door Trigger wire

The Gray/Black wire will trigger the alarm and is designed to be

connected to the door switch that turns on the dome light when

the door is opened. It is a negative input circuit only. If your

vehicle uses a positive door switch circuit, call for assistance in

making the connection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 5, Mounting the Receiver/Antenna

Receiver/antenna position should be discussed with the vehicle

owner prior to installation, since the antenna may be visible to

the vehicle’s operator.

The best location for the receiver/antenna is centered high on

either the front or rear windshield. For optimal range, the anten-

na should be mounted vertically. It can be mounted horizontally

in relation to the windshield or under the dashboard away from

metal, but range will be diminished. Metallic window tint can also

affect range, so this should be a consideration when determining

the mounting location.

After determining the best mounting location, follow these steps:

1. Clean the mounting area with a quality glass cleaner or

alcohol to remove any dirt or residue.

2. Plug the receiver/antenna cable into the

receiver/antenna.

3. Mount the receiver/antenna using the supplied double-

sided tape.

4. Route the receiver/antenna cable to the control module

and plug it into the four-pin antenna connector.

important! To achieve the best possible range,

DO NOT leave the antenna cable bundled under

the dash. Always extend the cable full length dur-

ing installation, regardless of the antenna mount-

ing location.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 6, Immobilizer Bypass Modules

Most newer vehicles have a factory engine immobilizer system

designed to prevent any unauthorized use of the vehicle. These

immobilizers will cut off power to the starter and the fuel supply

preventing a thief from starting the vehicle.

There are several types of immobilizers, with the most common

being the resistance-based passlock/passlock 2 systems found on

most newer GM vehicles. This system can be bypassed using the

20402, 29402 or 556L immobilizer bypass modules available at

your local authorized retailer or at www.directedstore.com. The

majority of transponder-based immobilizer systems can be

bypassed using the 20402, 29402 or 556U immobilizer bypass

module available at your local authorized retailer.

The WHITE/BLACK wire of the 6-pin harness supplies a 400mA (-)

output as soon as the control module begins the remote start

process. This wire can be used to activate an immobilizer bypass

unit.

note! Any vehicle equipped with a factory immobi-

lizer must use an immobilizer bypass module to

remote start. If not used, the vehicle ignition or

fuel supply circuits could lock up and require a

costly trip to the dealer to reset the computer sys-

tem.

To determine which bypass module your vehicle requires, use the

website Interface Module Look-Up tool at www.readyremote.com.

Download from Www.Somanuals.com. All Manuals Search And Download.

Step 7, Programming

Programming transmitters

Your system can learn up to 4 transmitters. The following proce-

dure will show you how to add additional transmitters or replace

old ones. Each transmitters can be programmed one button at a

time or you can use an auto learn procedure that learns the

intended factory configuration. Learning one button at a time is

generally only used when using one transmitters to control two

different cars. Being able to program functions to different chan-

nels on each transmitters prevents multiple cars from responding

simultaneously.

1. Turn the ignition ON

2. Press/release the momentary switch the same number of

times as the desired transmitter learn Step number, and

then Press/HOLD.

3. After Holding the momentary switch for 2 seconds the

LED will begin to flash to indicate of the accessed trans-

mitter learn Step.

4. Press the transmitter button that you want to control

the function assigned to that transmitter learns Step;

the Horn/Siren will emit a long chirp.

note! For transmitter learn Step #1, you must press

the “*” button on the transmitter, this will auto-

matically program the transmitter buttons to the

default function configuration. See the transmit-

ter button auto learn chart for the assignment

functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

You can learn more than one transmitter function at a time by

advancing to another transmitter learn Step.

To do this, first release the momentary SW and then press/release

it the same number of times as the difference between the current

transmitter learn Step and the desired transmitter learn Step, and

then press/HOLD it.

example! To advance from transmitter learn Step 2

to transmitter learn Step 8, release the momentary

SW and then press/release it 6 times and HOLD it

on the 7th press.

After Holding the Valet Sw for 2 seconds the LED will flash 8 times

and repeat. You can now learn a transmitter button to step 8.

There are several ways to exit transmitter Learning, by TimeOut,

Ignition or momentary SW Presses.

1. TimeOut: If more than 15 seconds elapse between

momentary SW presses or transmitter signals.

2. Ignition: If the Ignition is turned off at any time during

transmitter Learning.

3. Momentary SW presses: if you press/release the momen-

tary SW more times than transmitter Learning steps in

the menu.

The Horn output will pulse 5 times rapidly and the Led will turn

off to indicate exiting feature programming.

Download from Www.Somanuals.com. All Manuals Search And Download.

Transmitter Button Programming Chart

Step

Function

Auto-Program

Button Assignment

ALL buttons to the factory default functions

Remote Start/Stop function

Remote Start

Trunk Pop

Carfinder & Trunk Pop functions

Headlight/Panic/Silent Headlight, Silent mode & Panic functions

Arm & Lock

Arm & Lock function

Disarm & Unlock functions

Daily Start function

Disarm & Unlock

Daily Start

Vacation Mode

Vacation Start function

Delete ALL TXs

Removes ALL transmitters from memory

Transmitter Button Auto-Learn

Remote Start/Stop

CarFinder & Disarm/Trunk Pop

Head Light control, Panic & Silent mode

Arm & Lock

Disarm & Unlock

Vacation Mode

Daily Start

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming System Settings

Many of the features and operations of this system can be

changed to suit most of today's vehicle electrical systems. The

programming routine and feature menus that follow will allow

making the changes required for most vehicle installations.

System programming routine:

Accessing a Menu:

1. Turn the ignition ON and then OFF in less than 5 seconds

2. Within 3 seconds Press/Hold the Momentary Switch

3. After 2 seconds the LED will flash and the Horn/Siren

will pulse to indicate the available menus. It will toggle

through the outputs until a menu is chosen.

a. Menu 1: 1 LED flash and Horn/Siren pulse

b. Menu 2: 2 LED flashes and Horn/Siren pulses

4. Release the Momentary Switch after the appropriate

output to access that Menu. The LED and Horn/Siren

outputs will cease.

Accessing a Feature Location:

1. Press and release (do not hold) the Momentary Switch

the same number of times as the feature location to be

accessed. See the Feature Chart for locations.

2. After 2 seconds the LED will flash (the number of flashes

will match with the feature location) to confirm the

feature location. It will flash/pause and repeat until the

feature is changed or programming is exited.

3. Press a button on the transmitter to change the feature

Download from Www.Somanuals.com. All Manuals Search And Download.

option

a. Option 1: Press the transmitter button assigned to

the Remote Start function (usually the

set factory default Option 1.

button) to

The LED will turn ON and the Horn/Siren will pulse once.

b. Option 2-4: Press the transmitter button assigned to

the CarFinder function (usually the

Options 2-4 if available.

button) to set

The LED will flash and the Horn/Siren will pulse 2-4

times to indicate the option and the LED continue to

flash to indicate the option.

Access a different Menu:

To change features in a different menu or return to the beginning

of the accessed menu return to Step 2 under Accessing a Menu at

any time.

Advance to different feature location:

To advance to a new locations within the same menu

press/release the Momentary Switch the same number of times as

the difference between the feature locations.

example! to advance from feature location 2 to feature

location 8 press/release (do not hold) the Momentary

switch 6 times, after 2 seconds the LED will flash 8

times to indicate the newly accessed feature location.

Download from Www.Somanuals.com. All Manuals Search And Download.

Exiting Feature programming:

The following will cause the system to exit programming and is

indicated by 5 short chirps of the Horn/Siren output.

a. More than 15 seconds lapses between inputs by

Momentary switch or transmitter button

b. The ignition is turned on

Feature Menus

Feature Menu 1 Chart

Feature

Location

Feature Name

Option 1

(Default)

Option 2

Option 3

Option 4

Engine Monitoring

Run Time

No Tach

15 min

Normal

Ign 2

Tach

30 min

Crank time

ExtraCrank

ACC 2

Super crank

Mega crank

Ign2 Output

Wait-to-start

Activation Input

Vacation Temp

Alarm Disarm

Horn Output

Headlights

Diesel Input

wire

Diesel Timer

1 pulse

2 pulse

0 degrees F -10 degrees F -20 degrees F

1 second

450 ms

Horn/Pulsing Siren/Constant

Daytime

Light your

way

Start Chirp

Off

Reset All Options

Press ANY TRANSMITTER button to reset all

features

Download from Www.Somanuals.com. All Manuals Search And Download.

Feature Menu 1 Descriptions

1. Engine Monitoring: Defines how the engine is monitored while

the Remote Start is active.

1. No Tach: The battery voltage will be used to monitor the

engine while Remote Start is active.

2. Tachometer: The tachometer will be used to monitor

engine speed while Remote Start is active.

2. Run Time

1. 15 minutes: The Remote Starter will shut down after it

has been active for 15 minutes.

2. 30 minutes: The Remote Starter will shut down after it

has been active for 30 minutes.

3. Crank Time: Crank Time will be in effect only when Engine

Monitoring is "No Tach" and affects the duration of the "Yellow"

Starter Output wire.

1. Normal Crank: The Starter output will be 700mS.

2. Extra Crank: The Starter output will be 1 second.

3. Super Crank: The Starter output will be 1.4 seconds.

4. Mega Crank: The Starter output will be 2.1 seconds.

4. Ignition 2 Output: This controls the output type of the high

current "Green" ignition 2 output wire.

1. Ignition 2: Output will match the Blue Ignition 1

input/output wire operation during remote start.

2. Accessory 2: Output will match the White Accessory 1

output wires operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Wait-To-Start: This chooses the method of Starter output delay

for Diesel engines.

1. Diesel Input wire: An input on the "Red/Blk" wire will

delay the Start output until the input ceases.

2. Diesel Timer: The Starter output will be delayed until the

timer expires. The "Red/Blk" wire will be ignored.

6. Activation Input: Selects the number of inputs from the trans-

mitter or the "Red/Wht" activation input wire to activate the

Remote Starter.

1. 2 Pulses: Two input pulse will Start and Stop the Remote

Starter

2. 1 Pulse: One input pulse will Start and Stop the Remote

Starter

7. Vacation Temp: Selects the temperature threshold that will

activate the Remote Starter when Vacation Mode has been acti-

vated.

1. 0 Degrees F

2. -10 Degrees F

3. -20 Degrees F

8. Alarm Disarm: Selects the output duration of the "Brown/Wht"

Factory Alarm Disarm wire.

1. 1 second: The output will be 1 second in duration

2. 450mS: The output will be 450mS in duration

9. Horn Output: Selects the type of output on the "Blue" Horn

output wire when the alarm is fully triggered but does not affect

the arm/disarm/remote start/programming chirp outputs

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Horn: The output will be pulsed during full trigger events

2. Siren: The output will be constant during full trigger

events.

10. Headlights: Selects the operation of the "Yellow/Brn" head-

light output wire when an ignition input is sensed.

1. Daytime Running: The output will activate 10 seconds

after an ignition input is sensed and cease output 1

second after the ignition input ceases.

2. LightYourWay: The output will activate for 25 seconds

immediately after the ignition input ceases.

11. Start Chirps: Selects if the "Blue" Horn/Siren output wire will

pulse when activating Remote Starter.

1. On: The Horn output will pulse 1 time at the beginning

of Remote Start

2. Off: The Horn output WILL NOT pulse at the beginning

of Remote Start

12. NA: A feature is Not Available for this Location

13. Reset All Options: Pressing a transmitter button when this

Feature Location is accessed will "Reset All Options" in both

menus to their default setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Feature Menu 2 Chart

Feature

Location

Feature Name

Option 1

(Default)

Option 2

Option 3

Arming Type

Locking Type

Ignition Locking

Ignition Unlocking

Lock Pulses

Active

OFF

Passive

Lock w/Ign On

/ Brake

Unlock w/Ign

OFF

Unlock Pulses

Lock Duration

Alarm Mode

Short 0.8

seconds

Long 3.5

seconds

OFF

Auto Rearming

Alarm Chirps

ACC

OFF

Accessory

Domelight

Starter

Kill/Antigrind

Output

Pulses/Domelight/St Pulse (RAP)

arter kill

Feature Menu 2 Descriptions

1. Arming Type: Selects if the alarm will arm by one or both avail-

able methods.

1. Active: The alarm will arm via transmitter only

2. Passive: The alarm will arm via transmitter and Passive

Arming criteria.

2. Locking Type: Selects the type of arming operations the door

locks will activate with.

1. Active: The doors will lock when armed via transmitter

and Auto Re-arming.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Passive: The doors will lock when armed via transmitter,

Passive Arming and Auto Re-arming.

3. Ignition Locking: Selects if the door locks will activate after an

ignition input is sensed.

1. Off: The Door Lock output will not activate due to an

ignition input sense.

2. On: The Door Lock output will activate when the brake

input and an ignition input is sensed.

4. Ignition Unlocking: Selects if the door locks will activate after

the ignition input ceases.

1. Off: The Door Unlock output will not activate when the

ignition input ceases.

2. On: The Door Unlock output will activate 100mS after

the ignition is turned off.

5. Lock Pulses: Selects the number of pulses when locking the

doors.

1. 1 pulse: The Door Lock output will be one pulse for the

programmed duration.

2. 2 pulses: The Door Lock output will be 2 pulses for the

programmed duration.

6. Unlock Pulses: Selects the number of pulses when Unlocking the

doors.

1. 1 pulse: The Door Unlock output will be a single pulse

for the programmed duration.

2. 2 pulses: The Door Unlock output will be a double pulse

for the programmed duration.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Lock Duration: Selects the duration of the pulses when Locking

and Unlocking the doors.

1. Short pulse: The Door Lock & Unlock outputs will be

800mS in duration.

2. Long pulse: The Door Lock & Unlock outputs will be a

3.5 seconds in duration.

8. Alarm Mode: Selects if the alarm functions are active or

bypassed.

1. On: Alarm functions are operational as described

2. Off: Alarm functions are NOT operational, but conve-

nience features and Remote Starter still operate

normally.

9. Auto Re-arming: Selects if the units will automatically Re-

arm/lock itself if alarm inputs 1 or 6 are not activated after trans-

mitter disarm/unlock.

1. Off: The unit WILL NOT automatically Arm/Lock the

doors after transmitter Disarm/Unlock.

2. On: The unit will automatically Arm/Lock the doors 120

seconds after transmitter Disarm/Unlock if Alarm Inputs

1 or 6 remain idle.

10. Alarm Chirps: Selects if the "Blue" Horn output wire will pulse

when Arm/Lock and Disarm/Unlock are activated.

1. On: The Horn output will pulse 1 time for Arm/Lock and

2 times for Disarm/Unlock.

2. Off: The Horn output WILL NOT pulse for Arm/Lock or

Disarm/Unlock.

Download from Www.Somanuals.com. All Manuals Search And Download.

11. Acc pulse/DomeLight/ Starter Kill-Anti-grind: This controls

the output of the "Brown" output wire.

1. Accessory Pulse: This output will pulse 10sec after the

Remote Starter shuts down, except when the ignition

input is active.

2. Dome Light: This output will turn on for 25sec after the

Unlock output is completed, and cease if the Ignition is

turned on.

3. Starter Kill: This output will activate when the Alarm

system is Armed for disabling the vehicle starter circuit

and when remote started for Anti-grind.

Download from Www.Somanuals.com. All Manuals Search And Download.

System Diagnostics

Alarm diagnostics

When arming or disarming the alarm, this system will alert you of

alarm triggers or active inputs by changing the Horn/Siren and

light flash output. It will then indicate the active input by

flashing the LED.

Arming diagnostics:

When arming, if an alarm input is active (door or hood open) the

Horn/Siren output and Parking Lights will pulse three times

instead of one as an alert.

The LED will then flash/pause and then repeat 5 times to indicate

the active input (See alarm input chart)

The active input will be bypassed until it has been inactive for

more than 5 seconds but all other alarm inputs will be monitored

normally to assure the security of the vehicle

Disarming diagnostics:

When disarming, if the alarm was fully triggered in your absence,

the Horn/Siren output and Parking Lights will pulse four times

instead of two as an alert.

The LED will then flash/pause and then repeat 5 times to indicate

the input that caused the trigger (See alarm input chart).

note! If the alarm was triggered more than once, the

diagnostics will only report the last input that fully

triggered the alarm. Sensor War-away triggers are not

reported in diagnostics.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alarm Input Chart

LED Flashes

Input Description

The 'Gray/Blk' Input wire

The 'Orange' Brake Input wire

Sensor Input

The 'Violet' Hood Input

The 'Blue' Ignition Input wire

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote Start Diagnostics

Remote Start Diagnostics:

Remote Start diagnostics are an important tool that will diag-

nose the status of the remote start system by letting you know

why it remote started, shut down or refused to start as expected.

No Start Diagnostics:

If the system fails to activate Remote Start, Quick stop, Daily

Start or Vacation mode as expected the parking lights will flash

to indicate the reason. Consult the No Start Diagnostic Chart for

the reason.

No Start Diagnostic Chart

Remote Start

Feature

LED

Flashes

Description

Any

Indicates a loss of signal from the transmitter to

the system or a loss of power to the main unit.

Daily Start

The unit is in the Valet Mode or Battery Voltage is

below 11v when attempting to activate this

feature.

Vacation Mode

The unit is in the Valet Mode, Battery Voltage is

below 11v, or the Brake, Hood or Ignition inputs

are active

Remote Start

Quickstop

The unit is in the Valet Mode, Battery Voltage is

below 11v, or the Brake or Hood inputs are active

The unit is in the Valet Mode, Battery Voltage is

below 11v, or the Brake or Hood inputs are active

Download from Www.Somanuals.com. All Manuals Search And Download.

Last Start Diagnostics:

The system holds in memory the reason for the most recent

remote start activation. This diagnostic report must be recalled

using the following operation:

1. Turn the ignition ON and then OFF in less than 5 seconds

2. Within 5 seconds press and release the Monetary Switch

3. After 2 seconds the LED will flash/pause and repeat 5

times to indicate the cause of the most recent remote

start activation.

4. Count the LED flashes and consult the Last Start

Diagnostic Chart

Last Start Diagnostic Chart

LED

Description

Flashes

The Remote Starter has not been activated since the main power

was connected

The Transmitter was used to activate the Remote starter

The Activation Input wire was used to activate the Remote starter

Low temperature activated the Remote Starter in Vacation Mode

Low battery voltage activated the Remote Starter in Vacation Mode

No Diagnostics

Daily Start activated the Remote Starter

Download from Www.Somanuals.com. All Manuals Search And Download.

Shut Down Diagnostics:

The system holds in memory the reason for the most recent

remote start shut down. This diagnostic report must be recalled

using the following operation:

1. Step on the foot brake and hold until Step 4 has begun

2. Turn the ignition ON and then OFF in less than 5 seconds

3. Within 5 seconds press and release the Momentary

Switch

4. After 2 seconds the LED will flash/pause and repeat 5

times to indicate the cause of the most recent remote

start shut down.

5. Count the LED flashes and consult the Shut Down

Diagnostic Chart

Shutdown Diagnostic Chart

LED Flashes Description

The programmed Run Time expired

The 'Orange' Brake Input wire was activated

The Tachometer Input level fell below 50% of learned value

The Transmitter was used shut down remote start

The 'Violet' Hood Input wire was activated

Battery voltage level fell below required level

The alarm was fully triggered

The Tachometer Input level was x3 times learned value for >5sec

The "Red/Wht" activation Input was used shut down remote start

Download from Www.Somanuals.com. All Manuals Search And Download.

Testing the system

Once steps 1-7 have been completed, the operation of the system

can be tested.

Ensure that the two 30-amp fuses are in the relay harness PINK

wire fuse holders. Make sure that the vehicle is in park with the

emergency brake on and the hood closed. Press

2 times on

the remote to initiate the remote start function. The parking

lights should flash to confirm the remote start command has been

received, The accessories and ignition should turn on followed by

the starter cranking and the vehicle engine running (this may take

a moment to initiate). Pressing

2 times again on the remote

will shut the engine off. (See Programming System settings

section for 1 press remote start operation)

This completes the testing, if all functions do not work correctly

check your wiring against the manual and verify all connections.

If you still experience problems contact Directed Technical

Support at 1-800-477-1382.

Download from Www.Somanuals.com. All Manuals Search And Download.

Neutral Safety Test

Some vehicles do not have an electrical neutral safety switch.

Instead, a mechanical neutral safety switch that physically inter-

rupts the starter wire is used when the vehicle is in any drive gear.

If the remote start is interfaced before this switch, it will provide

protection from starting in gear.

However, some vehicles combine the column shift mechanism and

the mechanical neutral safety switch into one mechanical part. In

these vehicles, it is impossible to interface the remote start

system before the neutral safety switch. With this type of vehicle,

if the car is left in a drive gear and the remote start system is acti-

vated, the vehicle will move and may cause damage to persons or

property.

important! This test must be performed to deter-

mine if the vehicle will start while in gear. If the

vehicle attempts to start during this test you

must call Technical Support at 1-800-477-1382

for assistance before using the remote start fea-

ture.

Testing the Neutral Safety Switch

note! You must complete the remote start system

installation before doing the following test.

Ensure that the remote start system is function-

ing normally. This includes connecting to the

brake as a shut-down.

1. Make sure there is adequate clearance to the front and

rear of the vehicle because it may move slightly.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Make sure the hood is closed and there are no remote

start shut-downs active.

3. Set the emergency brake.

4. Turn the key to the "run" position, this will release the

shifter.

5. Place the shifter in the drive position.

6. Place your foot directly over the brake pedal, but do not

depress it. Be ready to step on the brake if the starter

engages.

7. Activate the remote start system.

8. If the starter does not engage, no additional safety

interfaces are required.

9. If the starter engages, immediately depress the brake to

shut the remote start system down.

IF THE ENGINE ATTEMPTED TO START THE VEHICLE THEN THE TEST

HAS FAILED

CALL TECHNICAL SUPPORT FOR ASSISTANCE AT 1-800-477-1382

warning! If the vehicle fails this test the remote

start must be disabled until the proper Safety

Interface has been installed that will keep the

vehicle from starting while in gear. Failure to do so

may result in property damage, injury or death.

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

The ignition comes on, but the starter will not crank.

➜

Does it start with the key in the ignition? If so, does the vehicle

have an engine immobilizer? Does it start with the brake pedal

depressed? (Make sure to disconnect the brake shutdown when

performing this test.) If so, it may have a brake/starter interlock.

Is the correct starter wire being energized? Check by energizing it

yourself with a fused test lead.

The starter cranks for 1 or 2-seconds but does not start.

➜

The wrong ignition wire is being energized or the system's ignition

and accessory wires have been connected backwards. Also, the

vehicle may have two ignition circuits. Try activating the unit with

the ignition key in the "run" position. If the vehicle then runs

normally, retest your ignition system.

The starter continues to crank after the car has started.

➜

Has the tach wire been learned? See the Tach Learning section of

this guide. Is the tach wire receiving the correct information?

Either the wrong tach wire has been used, or a bad connection

exists. Verify that all of the heavy gauge wires are plugged into

the correct tabs on the control unit. If they are incorrectly

connected, the starter could stay engaged.

The climate control system does not work.

➜

Either the wrong accessory wire is being energized or more than

one ignition or accessory wire must be energized in order to

operate the climate control system.

The remote start will not activate.

➜

Download from Www.Somanuals.com. All Manuals Search And Download.

Check to ensure that the hood is not open and that the brake

pedal is not depressed. Check harnesses and connections. Make

sure the harnesses are fully plugged into the remote start module.

Make sure there are good connections to the vehicle wiring. Check

voltage and fuses. Use a meter and check for voltage between the

RED wire and the BLACK ground wire. If you have less than battery

voltage, check both 30A fuses on the main power wires. Also make

sure that the ground wire is going to a good paint-free chassis

ground.

The remote start will activate but the starter never engages.

➜

1. Check for voltage on the YELLOW starter wire two seconds

after the remote start becomes active. If there is voltage

present, skip to Step 4. If there is no voltage present,

advance to Step 2.

2. Check the 30A fuses.

3. Does the vehicle have an immobilizer? Some Immobilizer

systems will not allow the vehicle to crank if active.

4. Check connections. The two PINK heavy gauge input wires

should have solid connections. "T-taps", or "scotch locks" are

not recommended for any high current heavy gauge wiring.

Also, if the vehicle has more than one 12-volt input wire,

then connect one PINK wire to each.

The vehicle starts, but immediately dies.

➜

Does the vehicle have an immobilizer? The vehicle's immobilizer

will cut the fuel and/or spark during unauthorized starting

attempts.

The vehicle will start and run only for about 10 seconds.

➜

Is the remote start module programmed for voltage sense? If so,

try programming the unit to tach mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

Model 24927

_➤Owner’s Guide

Download from Www.Somanuals.com. All Manuals Search And Download.

Owner’s Guide

Now that the installation is complete and tested, it is time to

learn about the many outstanding remote start, security and

convenience features that are included in your system.

Remote Start Features

➤

Remote Start your engine to warm or cool your vehicle

before driving

Quickstop Mode will keep the vehicle interior warm or

cool during short trips away from the vehicle

Daily Start for convenient engine warm up at a specific

time the following day

Vacation Mode maintains battery level when the vehicle

is parked for extended periods

Security and Convenience features

➤

The built in alarm will keep your vehicle secure when

parked and remote started

Keyless entry and starter kill outputs for convenience

and security

Panic Mode feature to call for help if you are threatened

while in or near your vehicle

CarFinder feature helps you find your vehicle in darkened

parking lots

Valet Mode will temporarily defeat the remote start and

alarm features but leave the convenience feature avail-

able

Download from Www.Somanuals.com. All Manuals Search And Download.

➤

Trunk pop output will disarm your alarm and open the

trunk as you approach your vehicle

Headlight output can operate as daytime running lights

for safety or light your way securely into your home or

office

➤

Switch Override will disarm the alarm system should you

loose your transmitter

Silent Mode will defeat the chirps for remote start or

arm/disarm temporarily when needed

Auto Re-arm will make sure your vehicle is locked at all

times if mistakenly unlocked

Transmitter Button Configuration

Using the Auto Learn operation for programming transmitters to

this system will result in the following transmitter icon operations.

controls the Remote Start/Stop functions

controls the CarFinder and Trunk Pop functions

controls the Headlight activation, Panic & Silent mode

functions

controls the Alarm Arm and Locking functions

controls the Alarm Disarm and Unlocking functions

activates the Vacation Mode feature

activates the Daily Start feature

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING YOUR SYSTEMS FEATURES

The Remote Start, Alarm and Convenience features described in

this section follow the transmitter button assignments using the

Auto-Learn step when programming a transmitter.

Remote Start Features

Remote Start allows you to remotely start and run your vehicle for

a programmed period of time. This makes it possible to warm up

the engine, as well as adjust the interior temperature of the

vehicle with the climate control system. If interior heating or

cooling is desired, the climate controls must be preset, and the fan

blower must be set to the desired level prior to remote starting the

vehicle.

Remote Start operation is completely disabled by placing the

system into the Valet Mode. The Remote Start, Quick Stop, Daily

Start and Vacation Mode features will not operate when in the

Valet Mode. See the Alarm Features section for information on

entering Valet Mode.

Remote Start the vehicle:

➤ Press the

button of the transmitter twice.

➤ The parking lights will flash once and the Horn/Siren

will chirp once to confirm that the vehicle will attempt

to start.

➤ The engine will start a few seconds after the parking

lights flash.

➤ Once started, the lights will flash and it will run for the

programmed period of time

Download from Www.Somanuals.com. All Manuals Search And Download.

note! If the lights flash more than once and the

engine does not start, refer to the No Start

Diagnostics for the cause.

important! Never remote start your vehicle when the

keys are in the ignition, except when activating Quick

Stop Mode, and never start the vehicle if it is not in

PARK and the Parking brake is not set.

important! It is unsafe to operate a vehicle's motor

in a garage or other closed off area. Breathing the

exhaust from the vehicle is hazardous to your health.

Never activate the remote start in an enclosed space.

When you are ready to drive the vehicle:

➤

Insert the ignition key and turn it to the ON (not the

START) position.

➤

Press the brake pedal, the remote start will shut down

and the engine will continue to run

note! If the brake pedal is pressed before the key is

in the ON position, the engine will shut down.

To shut down remote start:

The remote start can be shut down in several ways for convenience

by the user or for safety by the shut down inputs.

User remote start shut downs:

➤ The transmitter

button is pressed twice.

➤ Pulse the activation input wire twice

Download from Www.Somanuals.com. All Manuals Search And Download.

➤ The user steps on the brake as they begin to drive the

vehicle

Safety shut down inputs:

While the vehicle is running during remote start operation, the

system will monitor the vehicle and will automatically shut down

the engine if the system receives any of the following shutdowns

➤ The brake pedal is pressed.

➤ The hood is opened.

➤ The programmed run time has elapsed.

➤ The alarm is triggered

➤ Low battery voltage

➤ High or low tachometer signal

Quick Stop Mode

The Quick Stop feature allows the vehicle to remain running after

the key has been removed from the ignition. This feature is useful

for occasions when you wish to exit and lock the vehicle for short

periods of time, but would like to leave the motor running and the

climate controls on.

To activate Quick Stop:

➤

With the ignition On and the engine running, do one of

the following:

■ Press and release on the transmitter

button

twice.

■ Press and release the Momentary Switch 4 times

quickly

■ Pulse the activation input wire twice

Download from Www.Somanuals.com. All Manuals Search And Download.

➤

The Horn/Siren will chirp once and the lights will begin

flashing to indicate Quick Stop Mode is active.

Turn the ignition key to the OFF position. (The engine

will stay running.)

➤

Exit the vehicle and arm/lock the doors.

The engine will run for the programmed run time or until

a shut down input is activated.

note! Quick Stop mode will not activate if the

brake pedal is depressed.

Daily Start

The Daily Start feature will automatically start the engine 24 hours

after it has been activated. This is convenient if you leave your

house for work at the same time everyday. Simply activate as

described 24 hours before you wish for the engine to start.

To activate Daily Start:

➤

Press and hold the

mitter for more than 3 seconds

buttons on your trans-

The parking lights will flash 4 times and the Horn/siren

will chirp once to confirm Daily Start is activated.

Your vehicles engine will Remote Start in 24 hours.

note! The alarm and remote start functions will be

fully operational while Daily Start is active.

important! When Daily Start is active ONLY park you

car in a well ventilated areas.

Download from Www.Somanuals.com. All Manuals Search And Download.

To de-activate Daily Start:

➤

Press and hold the

buttons on your trans-

mitter for more than 3 seconds

➤

Activate Vacation Mode

The parking lights will flash 4 times to confirm Daily

Start has been de-activated. (The Horn/siren will not

chirp)

Vacation Mode

Vacation mode is a valuable feature designed to maintain normal

operating conditions when the vehicle is parked for extended

periods. Vacation mode will monitor and automatically start the

engine any time the system detects extremely low battery voltage

or temperatures (See Programming Section for available low

temperature settings).

To activate Vacation Mode:

➤

Press and hold the

mitter for more than 3 seconds

buttons on your trans-

The parking lights will flash 5 times and the Horn/Siren

will chirp once to confirm Vacation Mode is activated.

Your vehicles battery level and interior temperature will

be monitored and the engine will automatically start up

to 8 times.

➤

Temperature: the system will check the interior temper-

ature and start if required every three hours

Battery level: the system will start the engine immedi-

ately when the battery level drops below 11.5 volts.

Download from Www.Somanuals.com. All Manuals Search And Download.

note! The alarm functions will be fully operational

while Vacation Mode is activated.

important! When Vacation mode is activated ONLY

park you car in a well ventilated areas.

To de-activate Vacation Mode:

➤

Press and hold the

buttons on your trans-

mitter for more than 3 seconds

➤

Activate Daily Start

Activate the Ignition, Hood or Brake inputs at any time

The parking lights will flash 5 times to confirm Vacation

mode has been de-activated. (The Horn/siren will not

chirp)

Download from Www.Somanuals.com. All Manuals Search And Download.

Alarm and Security Features

Transmitter Arming of the Alarm

You can arm the system by pressing the

button of your trans-

mitter for one second. When the system arms, the Horn/Siren

output will chirp once and the parking lights will flash once.

If the power door locks are controlled by the system, the doors will

also lock. While the system is armed, the status LED will flash once

per second, indicating that the system is actively protecting your

vehicle.

If the Horn/Siren pulses and the lights flash 3 times, refer to the

Diagnostics Section. This indicates an alarm input is active at the

time of arming and should be checked. The LED will flash in groups

to indicate the active input.

Passive Arming of the Alarm

This system can be programmed to arm itself automatically (called

passive arming). If the system is programmed for passive arming,

it will automatically arm 30 seconds after the ignition is turned

off and the system detects that you have left the vehicle by

opening and closing a door.

Whenever the system is in its 30-second passive arming count-

down, the status LED will flash rapidly. At the 30-second point,

the Horn/Siren will chirp and the parking lights will flash to indi-

cate that the system is armed.

note! If the door, brake or hood inputs are acti-

vated during the 30 second countdown the

timer will stop and reset, it will re-start once

the input becomes inactive. Active sensor

inputs will not stop the countdown.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto-rearming feature

Auto-rearming is designed to protect the vehicle in case of unin-

tended disarming of the alarm.

It will automatically re-arm the alarm and lock the doors 120

seconds after any transmitter disarm occurs.

To stop Auto-rearm simply open a door or turn the ignition on

before the 120 seconds expires.

Alarm Input Operations

When armed the alarm has 6 inputs that will cause a full alarm

trigger output. Refer to the Alarm Diagnostic section for addi-

tional detail.

➤

The Door, Hood, Ignition and Brake inputs will cause an

immediate full trigger output when activated.

➤

The Sensor inputs can cause two types of outputs; Warn-

away and Full Trigger.

note! An optional two stage sensor is required for

the Sensor outputs to activate. Call Technical

Support for more information on compatible sensors.

Alarm Trigger Outputs

➤

Warn-away output: this output consists of 5 chirps of

the Horn/Siren output and 3 flashes of the parking

lights.

➤

Full Trigger output: this output consists of flashing the

Parking lights and the Horn/Siren output for 30 seconds

followed by a 5 second pause to monitor the alarm

inputs. If an alarm input is still active the output will

repeat.

Download from Www.Somanuals.com. All Manuals Search And Download.

Transmitter Disarming the Alarm

To disarm the security system, press the

button of the trans-

mitter. When the system disarms, the Horn/Siren output will chirp

twice and the parking lights will flash twice.

If the power door locks are controlled by the system, the doors will

also unlock. The LED will turn off and the vehicle can be entered.

If the Horn/Siren pulses and the lights flash 4 times, refer to the

Diagnostics Section. This indicates that the alarm was fully trig-

gered in your absence. The LED will flash in groups to indicate the

input that caused the trigger.

Momentary Switch Disarming the Alarm

If your transmitter is lost or will not disarm the alarm, you can

manually override it using your ignition key and the Momentary

Switch.

To override the Alarm using the Momentary Switch

➤

Enter the vehicle, the alarm will sound

Insert the key into the ignition and turn it to the On

position

➤

Immediately press and release the Momentary Switch 2

times

After 2 seconds the alarm will disarm as though the

transmitter had been used.

Panic Mode

This system includes a Panic Mode operation that will alert other

around you if you are threatened while in or near your vehicle. Due

to state laws the Panic Mode is defeated when the ignition is on.

Download from Www.Somanuals.com. All Manuals Search And Download.

To active Panic Mode:

➤

Press and hold the

seconds

button on the transmitter for 6

➤

The Horn/Siren output and light flash will activate for

45 seconds

To de-active Panic Mode:

➤

Press and release the

button on the transmitter

Arm or Disarm the alarm system

Zone Bypass Feature

The Zone Bypass feature temporarily bypasses alarm inputs that

trigger excessively when the system is armed while monitoring the

other inputs for triggers. This keeps constant triggers due to envi-

ronmental reasons from annoying the neighbors.

Protected entry bypass:

If the door, hood, brake or ignition inputs become activated

through 3 consecutive 30 second full trigger durations, it will be

bypassed until it has become inactive for more than 5 seconds.

Sensor bypass:

If one of the sensor inputs is triggered 3 times within 1 hour, a

bypass timer will begin and that input will be bypassed for 1 hour.

If a trigger occurs on that input while the bypass timer is active,

the bypass timer will reset.

You can Disarm and then Rearm the alarm to defeat the sensor

bypass at any time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Valet Mode

Valet Mode will defeat the alarm trigger and remote start opera-

tions while leaving all other security and convenience features

available such as Panic, Trunk Pop, Door Lock/Unlock and

Carfinder.

To enter Valet Mode:

➤

Press and hold the Momentary Switch

Turn the ignition On and Off in less than 5 seconds

Continue to hold the Momentary Switch

After 2 seconds the LED will turn on solid, Valet Mode is

entered

note! The LED will stay on only when the ignition

is off. After the ignition has been off for 24 hours

the LED will turn off until the ignition is cycled

on/off.

To exit Valet Mode:

➤

Press and hold the Momentary Switch

Turn the ignition On and Off in less than 5 seconds

Continue to hold the Momentary Switch

After 2 seconds the LED will turn off, Valet Mode is

exited

Download from Www.Somanuals.com. All Manuals Search And Download.

Convenience Features

Carfinder Feature

This feature allows you easily locate you vehicle in large and dark-

ened parking areas by pulsing the lights and Horn/Siren outputs.

To activate Carfinder:

➤

Press and release the

button on the transmitter

The headlight output, parking light output and the

Horn/siren output will pulse once

Silent Mode

Silent Mode allows you to temporarily delete the Horn/Siren

output when arming, disarming or activating remote start.

To use Silent Mode:

➤

Press and release quickly the

mitter

button on the trans-

➤

After 1 second press the transmitter button of the

feature to be activated without a Horn/Siren output

note! 10 seconds after step 1 the Horn/Siren output

will be re-activated. If silent Mode is your preferred

normal operation the Horn/Siren output can be pro-

grammed off in the feature menus. Then using Silent

Mode will temporarily turn on the Horn/Siren output.

Headlight Control

This feature allows you to toggle the headlight output on and off

anytime the ignition is off.

To activate the Headlights:

Download from Www.Somanuals.com. All Manuals Search And Download.

➤

Press and hold for 3 seconds the

transmitter and then release it.

button on the

The headlight output toggle on/off according to its

present state

note! The headlight output timer is 25 seconds

and is controlled by the ignition input according

to the programmed setting.

Trunk Pop

This feature allows you disarm the alarm, unlock the doors and

pop your trunk open with one press of a button

To activate the Trunk Pop:

➤

Press and hold for 3 seconds the

transmitter

button on the

➤

The alarm will disarm, unlock the doors and the auxiliary

output will pulse

Note: The auxiliary output will stay active until

the transmitter

button is released.

Download from Www.Somanuals.com. All Manuals Search And Download.

Glossary of terms

Control Module: The “brain” of your system. Usually hidden under

the dash area of the vehicle. It houses the microprocessor that

monitors your vehicle and controls all system functions.

FAD: Factory Alarm Disarm. Some vehicles with a factory alarm

require the alarm to be disarmed before remote starting.

RAP: Retained Accessory Power. After the vehicle is started and

then shut down, the power to the radio remains on (retained) until

a vehicle door is opened.

Transmitter: A hand-held, remote control which operates the var-

ious functions of your system.

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes

_________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

QUICK REFERENCE GUIDE:

Alarm Operation

■ To Arm and Lock: Press the

the parking lights and Horn/Siren will pulse once.

button for one second. The doors will lock and

■ To Disarm and Unlock: Press the

button for one second. The doors will

unlock and the parking lights and Horn/Siren will pulse twice.

Security and Convenience Features

■ Activate Panic Mode: Press and hold the

button for 6 seconds

button

■ Activate CarFinder: Press/release quickly the

■ Activate Headlights: Press and hold for 3 seconds and then release the

button

■ Open the Trunk: Press and hold the

button for 3 seconds

Remote Start the engine

■ To Start: Press the

button twice. The engine will start and the parking

lights will flash to confirm start.

■ To Stop: Perform the same steps as above to shut down remote start.

Quick stop Mode

■ To activate: Press the

button twice with ignition on and the engine run-

ning or press/release the Momentary Switch 4 times

■ To de-activate: Press the button twice or step on the brake

Daily Start

■ To activate: Press the

and

buttons for three seconds. The lights will

flash 4 times and the Horn/Siren will chirp once to confirm.

■ To de-activate: Perform the same step to exit, the parking lights will flash 4

times, the Horn/siren will not pulse

Vacation mode

■ To activate: Press the

and

buttons for three seconds. The lights will

flash 5 times and the Horn/Siren will chirp once to confirm.

■ To de-activate: Perform the same step to exit, the parking lights will flash 5

times, the Horn/siren will not pulse

Download from Www.Somanuals.com. All Manuals Search And Download.

The company behind this system is Directed Electronics

Since its inception, Directed Electronics has had one purpose, to provide consumers with

the finest vehicle security and car stereo products and accessories available. The recipient of

nearly 100 patents and Innovations Awards in the field of advanced electronic

technology, DIRECTED is ISO 9001 registered.

Quality Directed Electronics products are sold and serviced throughout North America

and around the world.

(800) 274-0200

Call

for more information about our products and services.

Directed Electronics is committed to delivering world class quality products

and services that excite and delight our customers.

Directed Electronics

Vista, CA 92081

www.directed.com

N24927 04-06

Download from Www.Somanuals.com. All Manuals Search And Download.

Q See Camping Equipment AND QSD2308 16 DVRS User Guide
Radio Shack Radio 120 0615 User Guide
Radio Shack Washer 49 1010 User Guide
Renesas Server HEW Target User Guide
Roberts Gorden Gas Heater CRV B 10 User Guide
Roland Electronic Keyboard HP505 User Guide
Samsung Bluetooth Headset WEP 300 User Guide
Samsung Printer ML 5050G User Guide
Samsung Projection Television SP 46L3HR, SP 50L3HR, SP 56L3HR, SP 61L3HR User Guide
Senco Power Screwdriver SG2500 User Guide