Vibrating Alarm Clock
OWNER’S MANUAL —
Please read before using this equipment.
63-1415
About 5 seconds after you install the
batteries, the clock vibrates and beeps three
times. 12:00 00 and M appear. Ô
Ô NOTE Ô
The default alarm time is set to 12:01. Press
SET/ALM to turn off the alarm before you set
the time. M disappears.
•
When the clock stops operating properly or
the display dims, replace the batteries.
•
•
Each time you press any button, the clock
beeps.
While setting the time, if you do not press a
key for about 30 seconds, the clock beeps
and returns to the current time display.
USING THE COVER
Your clock’s cover protects the display and
also serves as a stand so you can place the
clock on a table or other flat surface. To use
the cover as a stand, lift and open the cover
all the way.
MODE
•
•
The clock uses the 12-hour format. PM
appears for a PM hour.
SET/
ALM
While setting the alarm time, if you do not
press a key for about 30 seconds, the clock
beeps and returns to the current time display.
UP/
SNZ
START/
LIGHT
•
To turn on or off the alarm, press SET/ALM.
M appears when the alarm is turned on, and
disappears when the alarm is turned off.
SETTING THE TIME
1. Press MODE.
appears and the hour
O
Thank you for purchasing a RadioShack
Vibrating Alarm Clock. Your clock combines
a simple design with advanced technology.
You can set the clock to beep or vibrate
(without disturbing others around you) at the
preset time. Its lightweight design lets you
carry it anywhere.
digits flash. Ô
2. Repeatedly press (or hold down) UP/SNZ
to set the hour.
3. Press SET/ALM to store the hour. The
minute digits flash.
Clock Alarm beeps or vibrates at a time
4. Repeatedly press (or hold down) UP/SNZ
to set the minute. The second digits
automatically return to 00 when you
adjust each minute.
WARNING
Dispose of old batteries promptly and properly.
Do not burn or bury them.
you set.
o
o
Snooze Control temporarily silences the
alarm.
5. Repeatedly press MODE until the current
Backlight lights the display for about 3
seconds so you can see the time in the dark.
time appears. Ô
Timer lets you count down time from a
SETTING THE
ALARM TIME
You can set the clock to sound an alarm to
remind you of a daily event (such as a
meeting). Ô
preset time less than 24 hours.
ꢀ CAUTION ꢀ
Use only fresh batteries of the required size
Clock Cover protects the display and
serves as a stand.
•
and recommended type.
•
Do not mix old and new batteries, different
types of batteries (standard, alkaline, or
rechargeable), or rechargeable batteries of
different capacities.
INSTALLING
BATTERIES
1. Press MODE twice. L and 12:01 or the
last alarm time appear. The hour digits
flash.
Your clock requires two AAA batteries (not
supplied) for power. For the best
•
If you do not plan to use the clock for a month
or more, remove the batteries. Batteries can
leak chemicals that can destroy electronic
parts.
2. Repeatedly press (or hold down) UP/SNZ
performance and longest battery life, we
recommend RadioShack alkaline batteries.
ꢀ
to set the alarm hour.
3. Press SET/ALM. The minute digits flash.
o
1. Slide the clock’s battery compartment
cover on the back of the clock in the
direction of the arrow and remove it.
4. Repeatedly press (or hold down) UP/SNZ
to set the alarm minute.
5. Repeatedly press MODE until the current
2. Place two AAA batteries in the
compartment as indicated by the polarity
symbols (+ and –) marked inside.
time appears.
6. To check the alarm time, repeatedly
press MODE until L and the set alarm
time appear.
3. Replace the cover.
IMPORTANT
If an icon appears at the end of a paragraph, go to the box on that
page with the corresponding icon for pertinent information.
© 2002 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
!
!
— Warning Ô — Note
ꢀ— Caution
Download from Www.Somanuals.com. All Manuals Search And Download.
o
|