AC1030
OPERATOR’S MANUAL
„ AC1030 Replaces AC1025 For Use
With 7-Inch Diameter Dado Sets or
7-Inch Cutting Diameter Molding
Head
„ Use AC1030 With 6 to 8-Inch
Diameter Dado Sets or up to 8-
Inch Cutting Diameter Molding
Head
„ Fits RIDGID Model TS2400,
TS2412, TS2424, and TS3612
10-Inch Table Saws
DADO/MOLDING
HEAD INSERT
QUESTIONS OR COMMENTS?
CALL 1-866-539-1710
For Your Safety:
Read all instructions carefully
Download from Www.Somanuals.com. All Manuals Search And Download.
NPK pÉÅìêÉ=tçêâ
NVK kÉîÉê=pí~åÇ=lå=qççä
Use clamps or a vise to hold work
when practical. It’s safer than using
your hand, frees both hands to oper-
ate tool.
Serious injury could occur if the tool is
tipped or if the cutting tool is acciden-
tally contacted.
Do not store material above or near
the tool such that it is necessary to
stand on the tool to reach them.
OMK `ÜÉÅâ=a~ã~ÖÉÇ=m~êíë
NQK açåÛí=lîÉêêÉ~ÅÜ
Keep proper footing and balance at
all times.
NRK j~áåí~áå=qççäë=táíÜ=`~êÉ
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and chang-
ing accessories.
Before further use of the tool, a guard
or other part that is damaged should
be carefully checked to ensure that it
will operate properly and perform its
intended function. Check for align-
ment of moving parts, binding of mov-
ing parts, breakage of parts,
mounting, and any other conditions
that may affect its operation. A guard
or other part that is damaged should
be properly repaired or replaced. If
power cord is worn or cut, or dam-
aged in any way, have it replaced
immediately.
NSK aáëÅçååÉÅí=qççäë
Before servicing; when changing
accessories such as blades, bits, cut-
ters, etc.
NTK qç=oÉÇìÅÉ=qÜÉ=oáëâ=lÑ=^ÅÅáÇÉåí~ä=
pí~êíáåÖ=
Make sure switch is in “OFF” position
before plugging in. Turn switch “OFF”
in the event of a power failure.
NUK rëÉ=oÉÅçããÉåÇÉÇ=^ÅÅÉëëçêáÉë
Consult the operator’s manual for rec-
ommended accessories. Follow the
instructions that accompany the
ONK aáêÉÅíáçå=lÑ=cÉÉÇ
Feed work into a blade or cutter
against the direction of rotation of the
blade or cutter only.
accessories. The use of improper OOK kÉîÉê=iÉ~îÉ=qççä=oìååáåÖ=rå~íJ
accessories may cause hazards.
íÉåÇÉÇK
Turn power off. Don’t leave tool until it
comes to a complete stop.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
t^okfkdW For your own safety, turn
switch “OFF” and remove plug from
power source outlet before removing
insert.
1. Unplug the saw.
2. Remove the blade guard, the saw
blade insert, and the saw blade.
cä~íÜÉ~Ç=pÅêÉï
3. To remove insert:
a.Make sure saw is off and unplugged.
b. Loosen flathead screw.
c. Lift insert from front end, and pull
toward front of saw.
t^okfkdW= To reduce the risk of
injury from accidental start, make sure
switch is “OFF” and plug is not con-
nected to power source outlet.
1. Insert should be flush with table top.
Check as shown. Loosen flathead
screw that holds insert and adjust the
four set screws as necessary. Tighten
flathead screw. Do not tighten screw to
the point where it bends the insert.
rëÉ=pÉí=pÅêÉï=têÉåÅÜ
cìêåáëÜÉÇ=ïáíÜ=p~ï
t^okfkdW=Insert must be even with
the table surface. Inserts too high or low
can let the workpiece “snag” or catch on
uneven edges. Workpiece could twist
and kick back and could result in serious
personal injury.
2. Remove the dado/molding insert and
install the dado or molding head...
replace the insert.
rëáåÖ=íÜÉ=a~Çç=~åÇ=jçäÇáåÖ=fåëÉêí
klqbW=Do not install the outer loose collar
(the one next to the arbor nut) when
installing the dado or the dado set or
molding head.
Manual furnished with your table saw
and the instructions furnished with your
dado head or molding head.
2. The dado or molding head can be used
with the saw arbor tilted BUT NOT IN
ALL POSITIONS... NEVER TILT THE
ARBOR WHILE THE SAW IS RUN-
NING.
1. Before using the dado or the molding
head...or the insert, read and under-
stand the Safety and Operating instruc-
tions contained in the Operator’s
Download from Www.Somanuals.com. All Manuals Search And Download.
4
3. Rotate the dado or molding head man- 4. Never operate the saw without the
ually, (don’t touch it with your fingers,
but use a stick of wood) to be sure it
clears the insert before connecting the
power cord to the electrical outlet in
your shop.
proper insert installed.
5. When replacing the saw blade and saw
blade insert, always replace the blade
guard.
t^okfkdW=Always rotate the cutter
manually with the saw unplugged to as-
sure there is no contact with the saw or
insert. Failure to heed this warning can
result in serious personal injury.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
QUESTIONS OR COMMENTS?
CALL 1-866-539-1710
One World Technologies, Inc.
Hwy. 8
Pickens, SC 29671
3-8-06 (REV:00)
Download from Www.Somanuals.com. All Manuals Search And Download.
|