OPERATOR’S MANUAL
ROUTER
WITH FIXED AND PLUNGE BASES
DOUBLE INSULATED
R2900
Your router has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
with your finger on the switch or plugging in power tools
that have the switch on invites accidents.
WARNING:
Read all instructions. Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury. The term “power
tool” in all of the warnings listed below refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
SAVE THESE INSTRUCTIONS
WORK AREA SAFETY
Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry, or long hair can be caught
in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust-related hazards.
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adaptor plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts, and
any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Dam-
aged or entangled cords increase the risk of electric
shock.
When operating a power tool outdoors, use an ex-
tension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric
shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a haz-
ardous situation.
Use safety equipment. Always wear eye protec-
tion. Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
Avoid accidental starting. Ensure the switch is in the
off-position before plugging in. Carrying power tools
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
When servicing a power tool, use only identical
replacement parts. Follow instructions in the main-
tenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may
create a risk of shock or injury.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
WARNING!
To reduce the risk of injury, user must read
instruction manual.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when per- Check damaged parts. Before further use of the
forming an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the cutting
tool “live” and shock the operator.
tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body leaves it unstable
and may lead to loss of control.
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 14 is rec-
ommended for an extension cord 50 feet or less in
length. A cord exceeding 50 feet is not recommended.
If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord. An undersized
cord will cause a drop in line voltage resulting in loss of
power and overheating.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT safety
glasses. Following this rule will reduce the risk of serious
personal injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
Inspect tool cords periodically and, if damaged, have
repaired at your nearest authorized service center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
Bits coast after router has been turned off.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Frequency (cycles per second)
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
Revolutions, strokes, surface speed, orbits etc., per minute
.../min
Do not expose to rain or use in damp locations.
Wet Conditions Alert
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields
and, as necessary, a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in seri-
ous personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Hot Surface
To reduce the risk of injury or damage, avoid contact with any
hot surface.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
CAUTION:
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt
to use this product until you read thoroughly and
understand completely the operator’s manual.
If you do not understand the warnings and
instructions in the operator’s manual, do not use
this product. Call RIDGID customer service for
assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result
in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses
with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked
to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
DOUBLE INSULATION
EXTENSION CORDS
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protect-
ing insulation. Double insulated tools do not need to be
grounded.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the tool will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
WARNING:
When working outdoors with a tool, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” on the cord’s jacket.
The double insulated system is intended to protect
the user from shock resulting from a break in the
tool’s internal wiring. Observe all normal safety
precautions to avoid electrical shock.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
NOTE: Servicing of a tool with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the tool to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
**Ampere rating (on tool data plate)
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
16
14
16
14
12
14
14
10
14
12
—
ELECTRICAL CONNECTION
100'
This tool has a precision-built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
a loss of power and the motor will overheat. If the tool does
not operate when plugged into an outlet, double-check the
power supply.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on
lumber, tools or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
WARNING:
Check extension cords before each use. If
damaged replace immediately. Never use tool with
a damaged cord since touching the damaged area
could cause electrical shock resulting in serious
injury.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Depth of Cut..................................................................2 in.
Depth of Plunge......................................................2-1/2 in.
Collet...................................................................1/4, 1/2 in.
Peak Horsepower.................................................2-1/4 HP
No Load Speed ...................................10,000-23,000/min.
Input ................................120 V, 60 Hz, AC only, 12 Amps
VARIABLE
SPEED DIAL
LIGHTED PLUG
SLIDE
SWITCH
MOTOR IN
FIXED BASE
LED
WORKLIGHTS
PLUNGE BASE
CHIP
SHIELD
LOCKING
ARM
ADJUSTMENT BAR
PLUNGE DEPTH
ADJUSTMENT KNOB
Fig. 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR ROUTER
PLUNGE DEPTH ADJUSTMENT KNOB
The plunge depth adjustment knob, located on the base of
the plunge base, provides precise stops for repetitive depth
of cut changes. A depth adjustment scale makes quick ad-
justments to depth of cut changes possible.
See Figure 1.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
CENTERING TOOL
The centering tool aligns the subbase with the center of the
collet when reattaching the subbase to the router.
SLIDE SWITCH
The slide switch is located on top of the motor housing.
It features a soft start to prolong motor life and gives the
operator more control when starting the router.
CHIP SHIELD
Aclearplasticchipshieldisinstalledonthefrontoftherouter
for protection against flying dust and chips. The shield is
designed to fit the opening of the router base.
SPINDLE LOCK
The spindle lock keeps the collet from turning while
installing and removing bits.
LED WORKLIGHTS
The LED worklights, located on the bottom of the router
motor, illuminate when the slide switch is on. This provides
extra light for increased visibility.
VACUUM ADAPTORS
The vacuum adaptors attach to the router base for dust free
routing when used in combination with a vacuum.
VARIABLE SPEED DIAL
The variable speed dial enables speed adjustment of the bit
from 10,000/min to 23,000/min.
LIGHTED PLUG
The lighted plug with tool icon helps to easily identify live
tools.
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
WARNING:
If any parts are damaged or missing do not operate
this tool until the parts are replaced. Failure to
heed this warning could result in serious personal
injury.
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
WARNING:
fully inspected and satisfactorily operated the tool.
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
PACKING LIST
Router Motor
Fixed Base
Plunge Base
WARNING:
Router Table Attachment Screws (3)
1/2 in. Collet
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
1/4 in. Collet
1-1/4 in. Vacuum Adaptors (2)
Vacuum Adaptor Screws (2)
Centering Tool
Collet Wrenches (2)
T-Handle Wrench
Operator's Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
FIXED BASE
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
SPINDLE
LOCK
LOCK
LEVER
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
TO
UNLOCK
MOTOR
WARNING:
HOUSING
Never attempt to use the router motor without first
installing it in one of the approved bases. Failure
to heed this warning could result in personal injury
and damage to the motor.
ADJUSTMENT
BAR TAB
SLOT IN
MOTOR BASE
CAUTION:
Do not tighten the lock lever without the motor
installed in the base. Failure to heed this caution
may result in damage to the mechanism.
ADJUSTMENT
BUTTON
ADJUSTMENT
BAR
Fig. 2
APPLICATIONS
You may use this tool for the purposes listed below:
After the slot in the motor has cleared the tab, release the
adjustment button and press and hold the spindle lock
(until it fully locks in the collet spindle) so that it slides
behind the fixed base housing.
Rout grooves, carve designs, mortise door jambs, and
create joints in wood and wood products
Cabinet making, routing counter tops, and finishing work
NOTE: When using the spindle lock for any application,
make sure that the button goes all the way in. If the
button is depressed and does not go all the way in, turn
the collet with the wrenches provided until the spindle
lock locks into place.
in wood and wood products
SWITCHING FROM FIXED BASE TO PLUNGE
BASE
See Figures 2 - 3.
Pull the base until it dislodges from the subbase. Use
caution, as forcing may result in permanent damage to
the locking mechanism.
To remove the fixed base:
Unplug the router.
Loosen the lock lever on the fixed base.
To install the plunge base:
Unplug the router.
NOTE: It should not be possible to move the router
motor with the lock lever tightened and the motor cor-
rectly installed in either base. If movement is possible
with the lock lever tightened in either of the bases, an
adjustment to the lock lever needs to be made. See
Adjustments.
Loosen the lock lever.
Tighten the locking arm for stability.
Depress and hold the spindle lock until it fully locks in the
collet spindle.
Hold the router motor with one hand, and with the other,
Align the router motor tab with the slot in the plunge
depress and hold the adjustment button.
base.
Pull the adjustment bar tab from the slot in the motor
base.
Lift the motor up from the slot until the adjustment bar
tab passes out of the slot area.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Push the base until it lodges into the motor housing.
The spindle lock can be released once the motor slides
inside plunge base. It will disengage once it has cleared
the inside of the plunge base. Use caution as forcing may
result in permanent damage to the locking mechanism.
GROOVE IN
PLUNGE BASE
LOCK
LEVER
Tighten the lock lever.
Loosen the locking arm if needed.
SWITCHING FROM PLUNGE BASE TO FIXED
BASE
See Figures 3 - 4.
To remove the plunge base:
Unplug the router.
TO
UNLOCK
Loosen the lock lever.
Tighten the locking arm for stability.
Depress and hold the spindle lock (until it fully locks in
the collet spindle) so that it will slide behind the plunge
base housing.
Fig. 3
LOCKING ARM
PLUNGE BASE
Pull the base until it dislodges from the motor hous-
ing. Use caution, as forcing may result in permanent
damage to the locking mechanism. The spindle lock can
be released once the motor slides up into the plunge
base. It will disengage once it has cleared the inside of
the plunge base.
To install the fixed base:
Unplug the router.
Loosen the lock lever on the fixed base.
Depress and hold the spindle lock until it fully locks in
the collet spindle.
Push the base until it lodges into the motor housing. The
spindle lock can be released once the motor slides down
into the fixed base. It will disengage once it has cleared
the inside of the fixed base. Use caution as forcing may
result in permanent damage to the locking mechanism.
SPINDLE
LOCK
LOCK
LEVER
TO
UNLOCK
Depress and hold the adjustment button.
Place the adjustment bar tab in the slot on the motor
MOTOR
HOUSING
base.
Fig. 4
Tighten the lock lever.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
COLLET
NUT
TO
LOOSEN
WARNING:
If the collet nut is not securely tightened, the bit
may detach during use, causing serious personal
injury.
WARNING:
TO
TIGHTEN
ATTACH SUPPLIED
WRENCH HERE IF
NOT PRESSING
SPINDLE LOCK
DOWN WITH THUMB
AS SHOWN
Do not use bits which are larger than 2-1/4 in.
Never use bits which are larger in diameter than
the opening in the router subbase. These situations
could cause possible loss of control or create other
hazardous conditions that could cause possible
serious personal injury.
SPINDLE
LOCK
CAUTION:
To prevent damage to the spindle or spindle lock,
always allow motor to come to a complete stop
before engaging the spindle lock.
Fig. 5
INSTALLING/REMOVING BITS
See Figure 5.
Unplug the router.
WARNING:
If you are changing a bit immediately after use, be
careful not to touch the collet nut, bit, or collet with
your hands or fingers. You will get burned because
of the heat buildup from cutting. Always use the
wrench provided.
WARNING:
Before performing any adjustment, make sure the
tool is unplugged from the power supply and the
switch is in the OFF position. Failure to heed this
warning could result in serious personal injury.
INSTALLING/REMOVING COLLETS
To install the bit:
The router has two different size collets, a 1/2 in., and a 1/4
in. The 1/4 in. collet should be used with smaller bits for
finer work, while the 1/2 in. collet can be used with larger
bits that require heavier use.
Using the supplied wrench, hold the collet nut with one
wrench or depress and hold the spindle lock until it locks
into place.
Loosen the collet nut and remove the bit.
The collet must be attached to the collet nut before it is put
into the shaft.
Insert the bit until the it is approximately 1/8 in. to 1/4 in.
away from the collet nut face.
To remove collet:
NOTE: Make sure that the collet always clamps the shank
(non-cutting end) of the bit.
Unplug the router.
Using the supplied wrench, hold the collet nut with one
wrench or depress and hold the spindle lock until it locks
into place.
Tighten the collet nut securely by turning it clockwise with
the wrenches provided.
Release the spindle lock if necessary.
Loosen the collet nut and remove.
Release the spindle lock if necessary.
To install collet:
WARNING:
Bit continues to rotate after the router has been
turned off. To avoid injury, wait until the bit has
come to a complete stop before removing router
from the workpiece.
Unplug the router.
Using the supplied wrench, hold the collet nut with one
wrench or depress and hold the spindle lock until it locks
into place.
Attach collet assembly to collet shaft.
Tighten the collet nut securely by turning it clockwise with
the wrenches provided.
Release the spindle lock if necessary.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
To remove the bit:
Using the supplied wrench, hold the collet nut with one
wrench or depress and hold the spindle lock until it locks
into place.
DEPTH
ADJUSTMENT
KNOB
Loosen the collet nut and remove the bit.
Release the spindle lock if necessary.
TO
TO
DECREASE
DEPTH
SELECTING DEPTH OF CUT
LOCK INCREASE
Proper depth of cut depends on several factors: the horse-
power of the router motor, the type of bit, and the type of
wood. A lightweight, low horsepower router is designed for
making shallow cuts; a router with higher horsepower is
designed for deeper cuts. Small bits, such as veining bits
with 1/16 in. cutting diameters, are designed to remove only
small amounts of wood. Large bits, such as straight-flute
bits, remove larger amounts of wood and make deeper cuts
in soft woods, such as white pine.
LEVER
DEPTH
1
2
3
6
4
1
0
64
1
2
6
3
4
1
0
64
SCALE
BIT
INDICATOR
POINT
Choose a depth of cut that will not place excessive strain on
the router motor. If you need extra force or the motor speed
slows down considerably, turn off the router and reduce the
depth of cut. Then, make the cut in two or more passes.
Fig. 6
When routing a groove that is too deep to safely cut in one
pass, make the cut in several passes. We recommend that
cuts be made at a depth not exceeding 1/8 in. and that
several passes be made to reach deeper cuts.
T-HANDLE
WRENCH
TO
TO
DECREASE
DEPTH
INCREASE
DEPTH
SETTING DEPTH OF CUT FOR FIXED BASE
ROUTING
See Figures 6 - 7.
SLOT IN
SUBBASE
The bit depth can be adjusted by turning the depth adjust-
ment knob clockwise or counterclockwise. The depth of the
cut can be read on the depth adjustment knob. Each mark
on the scale indicates a 1/64 in. change in depth setting.
ADJUSTING
NUT
Unplug the router.
Loosen the lock lever.
Turn the depth adjustment knob counterclockwise to
move the collet down or clockwise to move the collet
up.
TO
LOCK
LEVER
LOOSEN
NOTE: It should not be possible to make depth adjust-
ments with the lock lever tightened. If depth adjustments
are possible with the lock lever tightened, an adjustment
to the lock lever needs to be made. See Adjustments.
Fig. 7
When the desired depth of cut is set, tighten the lock
lever.
Insert the T-handle wrench through the hole in the router
table into the hole on the subbase, and place the end of
the wrench socket over the adjusting nut.
NOTE: To adjust the depth of cut when the router is mounted
to a router table, loosen the lock lever, turn the depth adjust-
ment knob until the bit reaches the desired depth of cut, and
retighten the lock lever.
Turn the wrench counterclockwise to move the collet
down or clockwise to move the collet up.
When the router is mounted to a router table, depth adjust-
ments can be made easily by using the supplied T-handle
wrench.
NOTE: It should not be possible to make depth adjust-
ments with the lock lever tightened. If depth adjustments
are possible with the lock lever tightened, an adjustment
to the lock lever needs to be made. See Adjustments.
To make through table adjustments:
Unplug the router.
When the desired depth of cut is set, tighten the lock
Loosen the lock lever.
lever.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DEPTH OF CUT
SCALE
WARNING:
2
Do not use with router tables that fail to conform
to safe woodworking practices and offer proper
guarding for the bit. Use router tables that are UL
classified and identified suitable for use with the
specific router model. Failure to comply can result
in an accident causing possible injury.
DEPTH
INDICATOR
112
1
1
2
LOCKING
ARM
0
2
112
1
WARNING:
Only use router tables with proper guarding
for the bit and with on-board switch controlled
receptacles. Failure to use router tables with
appropriate safety features could result in serious
personal injury.
1
2
0
0
4
1
ADJUSTMENT
BAR KNOB
SETTING DEPTH OF CUT FOR PLUNGE BASE
ROUTING
See Figures 8 - 9.
ADJUSTMENT
BAR
The bit depth can be adjusted on the plunge base with a two
way system. The adjustment bar measures bit depth in 1/32
in., while the plunge depth adjustment knob on the plunge
base measures depth cuts in 1/64 in.
BIT
PLUNGE DEPTH
ADJUSTMENT KNOB
Fig. 8
The plunge base adjustment knob, located on the base of
the router, and the adjustment bar, located on the side of
the router, make it possible to make deep or heavy cuts in
successive passes. A preset cutting depth is achieved by
plunging the router until the adjustment bar comes in contact
with the plunge base adjustment knob.
LOCKING
ARM
0
1 4
The adjustment bar and the plunge base adjustment knob
can be used together to find a “zero” depth of cut, or any
depth of cut setting that is chosen as a starting point for a
particular task.
2
112
1
SCALE
1
2
Unplug the router.
0
Place the plunge base on a flat surface or on the
DEPTH
INDICATOR
workpiece.
Loosen the locking arm if needed.
Loosen the adjustment bar knob.
Plunge the router to the selected depth, making sure the
adjustment bar contacts the plunge depth adjustment
knob. This will provide a positive stop at “zero” depth of
cut.
ADJUSTMENT
BAR KNOB
ADJUSTMENT
BIT
BAR
Lock the locking arm if needed.
PLUNGE DEPTH
ADJUSTMENT KNOB
Tighten the adjustment bar knob.
Fig. 9
NOTE: The depth indicator on the adjustment bar can be
reset by loosening the adjustment bar knob and sliding
the depth indicator to the desired position. Tighten the
adjustment bar knob when depth is set.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
For further adjustments:
ON
Unplug the router.
Unlock the locking arm if needed.
Loosen the adjustment bar knob.
Use the depth indicator to measure the desired depth of
cut for cuts measurable in 1/32 in.
Tighten the adjustment bar knob.
Plunge the router to the selected depth, making sure the
adjustment bar contacts the plunge base adjustment
knob.
SLIDE
SWITCH
Retighten the locking arm if needed.
Fig. 10
OFF
For finer cutting with the plunge depth adjustment
knob:
TO
DECREASE
SPEED
Unplug the router.
Unlock the locking arm if needed.
Loosen the adjustment bar knob.
Set the plunge depth adjustment knob to the desired set-
ting. Turn clockwise to lower the plunge depth adjustment
knob, and counterclockwise to raise it.
NOTE: The plunge base adjustment knob provides depth
of cut adjustments from 0-1/2 in. from the highest or low-
est setting. Each 90˚ click on the plunge depth adjustment
knob indicates a change in the depth of cut by 1/64 in. A
full 360˚ clockwise rotation on the plunge depth adjust-
ment knob represents 1/16 in.
TO
INCREASE
SPEED
VARIABLE
SPEED DIAL
Depending on how deep the following cuts will need to be,
plunge the router until the tip reaches the desired starting
depth of cut using the adjustment bar as a depth stop.
Fig. 11
VARIABLE SPEED DIAL
See Figure 11.
NOTE: This will be the starting depth of cut for the routing
work.
The router has a variable speed dial designed to allow
the operator control and adjustment of speed and power
limits.Thespeedandpoweroftheroutercanbeincreasedor
decreased by rotating the variable speed dial in the direction
of the arrows shown in figure 11.
Lock the locking arm if needed.
Tighten the adjustment bar knob.
For successive cuts:
Unplug the router.
NOTE: Hold the router in normal operating position and turn
the variable speed dial to the higher numbers to increase
speed and power. Turn to the lower numbers to decrease
speed and power.
Adjust the adjustment bar knob to the desired height.
Loosen the locking arm if needed.
Plunge router until plunge depth adjustment knob and
adjustment bar touch.
Avoid running the router at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the router to become overheated. If this occurs, cool
the router by running it without a load and at full speed.
Retighten locking arm if needed.
TURNING THE ROUTER ON AND OFF
See Figure 10.
To adjust the router speed, turn the variable speed dial to
the desired speed setting.
The router features a soft start which allows for a gradual
increase in speed from 0/min. to the variable speed dial
setting. For example, if the router is set at 16,000/min. at
the time it is switched off and is then activated again, the
motor is designed to gradually rev up to that speed instead
of starting out at the full 16,000/min.
To turn the router on, push the switch to the ( I ), or ON
position. Return the switch to the ( O ), or OFF position when
routing operation is finished.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATING THE ROUTER
See Figures 12 - 13.
When routing straight cuts across a workpiece, clamp a
straight edge to the workpiece to use as a guide.
NOTE: Edge guides for the router are also available. See
WORKPIECE
Accessories.
STRAIGHT
EDGE
Position the straight edge parallel to the line of cut and offset
the distance between the cutting edge of the bit and the edge
of the router base. Hold the router base against the straight
edge and rout the groove.
When routing a groove wider than the diameter of the bit,
clamp a straight edge on both sides of the cut lines. Position
both guides parallel to the desired line of cut and spaced
equal distances from the desired edges of the groove. Rout
along one guide then reverse direction and rout along the
other guide. Clean out any remaining waste in the center of
the groove.
When routing a groove, the travel should be in a direction
that places the guide you are using at the right-hand side.
When the guide is positioned as shown in the “guide inside”
illustration (figure 17), tool travel should be from left to right
and counterclockwise around curves. When the guide is
positioned as shown in the “guide outside” illustration (figure
17), tool travel should be from right to left and clockwise
around curves. If there is a choice, the first setup is generally
the easier to use. In either case, the sideways thrust you use
is against the guide.
CLAMP
Fig. 12
INTERNAL ROUTING
Tilt router and place on workpiece without the bit contact-
STRAIGHT
EDGE
ing the workpiece.
Turn the router on and let the motor build up to full
speed.
Gradually feed bit into the workpiece until the subbase
is level with the workpiece.
Upon completion of the cut, turn the router off and let the
bit come to a complete stop before removing the router
from the workpiece.
EDGE ROUTING
Clamp a straight edge to the workpiece as a guide.
Place the router on the edge of the workpiece without
the bit contacting the workpiece.
Turn router on and let the motor build up to full speed.
WORKPIECE
Gradually feed the bit into the workpiece using the
CLAMP
clamped straight edge as a guide.
Fig. 13
Upon completion of the cut, turn the router off and let the
bit come to a complete stop before removing the router
from the workpiece.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Do not use large router bits for freehand routing.
Use of large router bits when freehand routing
could cause loss of control or create other
hazardous conditions that could result in personal
injury. If using a router table, large bits should be
used for edging only.
FREEHAND ROUTING
See Figure 14.
When used freehand, the router becomes a flexible and
versatile tool. This flexibility makes it possible to easily rout
signs, relief sculptures, etc. When freehand routing:
Draw or layout the pattern on the workpiece.
Choose the appropriate bit.
Fig. 14
NOTE: A core box or V-groove bit is often used for rout-
ing letters and engraving objects. Straight bits and ball
mills are often used to make relief carvings. Veining bits
are used to carve small, intricate details.
ROUTER
WORK
Rout the pattern in two or more passes. Make the first
pass at 25% of the desired depth of cut. This will pro-
vide better control as well as being a guide for the next
pass.
NOTE: Do not rout deeper than 1/8 in. per pass.
PILOT
EDGING WITH PILOT BIT
See Figure 15.
TOP EDGE SHAPING
ROUTER
The arbor-type bits with pilots are excellent for quick, easy,
edge shaping of any workpiece edge that is either straight
or curved at a curvature as great or greater than the radius
of the bit to be used. The pilot prevents the bit from mak-
ing too deep a cut; and holding the pilot firmly in contact
with the workpiece edge throughout prevents the cut from
becoming too shallow.
GUIDE
WORK
Whenever the workpiece thickness together with the desired
depth of cut (as adjusted by router depth setting) are such
that only the top part of the edge is to be shaped (leaving
at least a 1/16 in. thick uncut portion at bottom), the pilot
can ride against the uncut portion, which serves to guide it.
However, if the workpiece is too thin or the bit set too low
so that there will be no uncut edge to ride the pilot against,
an extra board to act as a guide must be placed under the
workpiece. This “guide” board must have exactly the same
contour— straight or curved—as the workpiece edge. If it is
positioned so that its edge is flush with the workpiece edge,
the bit will make a full cut (in as far as the bit radius). On the
other hand, if the guide is positioned as shown in figure 15
(out from the workpiece edge), the bit will make less than a
full cut — which will alter the shape of the finished edge.
PILOT
WHOLE EDGE SHAPING
Fig. 15
NOTE: Any of the piloted bits can be used without a pilot for
edge shaping with guides, as preceding. The size (diameter)
of the pilot that is used determines the maximum cut width
that can be made with the pilot against the workpiece edge
(the small pilot exposes all of the bit; the large one reduces
this amount by 1/16 in.).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DIRECTION OF FEED AND THRUST
6
5
See Figures 16 - 17.
3
The router motor and bit revolve in a clockwise direction. This
gives the tool a slight tendency to twist in a counterclockwise
direction, especially when the motor revs up.
PROPER
CUTTING
SEQUENCE
2
4
Feed the router into the workpiece from left to right. When
fed from left to right, the rotation of the bit pulls the router
against the workpiece. If fed in the opposite direction, the
rotation of the spinning bit will tend to throw the router away
from the workpiece causing kickback. This could cause you
to lose control of the router.
1
8
7
1/4 in. to 1 in.
Fig. 16
THRUST
Because of the high speed of bit rotation during a proper
feeding operation, there is very little kickback under normal
conditions. However, if the bit strikes a knot, hard grain,
or foreign object that affects the normal progress of the
cutting action, there will be a slight kickback. The direction
of kickback is always in the direction opposite bit rotation.
This will affect the trueness of the cut.
GUIDE INSIDE
ROTATION
GUIDE
To guard against kickback, plan the setup and direction of
feed so that you will always be thrusting the tool in the same
direction that the leading edge of the bit is moving. The thrust
should be in a direction that keeps the sharp edges of the
bit continuously biting straight into new (uncut) wood.
ROTATION
FEED
GUIDE OUTSIDE
NOTE: For best results, make sure to take enough time to
set up for cutting. While cutting, make sure to use the proper
rate of feed.
ROTATION
THRUST
PROPER RATE OF FEED
Professional routing depends upon careful setup and proper
rate of feed which is learned through practice and use. The
proper rate of feed is dependent upon:
ROTATION
hardness and moisture content of the workpiece
depth of cut
cutting diameter of the bit
FEED
GUIDE
Fig. 17
When cutting shallow grooves in soft woods such as pine, a
faster rate of feed can be used. When making cuts in hard-
woods such as oak, a slower rate of feed is required.
Several factors will help you select the proper rate of feed. Notice the chips being produced as you cut. If the router
is fed too slowly, it will scorch or burn the wood. If fed
too fast, it will take large chips out of the wood and leave
gouge marks.
Choose the rate that does not slow down the motor.
Choose the rate at which the bit advances firmly and
surely to produce a continuous spiral of uniform chips
or a smooth edge.
Test a cut on a scrap piece of the workpiece before you
begin. Always grasp and hold the router firmly with both
hands.
Listen to the sound of the motor. A high-pitched sound
means you are feeding too slowly. A strained, lower
pitched sound signals force feeding.
If you are making a small diameter, shallow groove in soft,
dry wood, the proper feed rate may be determined by the
speed at which you can travel the router along the guide line.
If the bit is a large one, the cut is deep, or the workpiece is
hard to cut, the proper feed may be a very slow one. A cross
grain cut may require a slower pace than an identical with
grain cut in the same workpiece.
Check the progress of each cut. Too slow feeding can
cause the router to take off in a wrong direction from the
intended line of cut. Force feeding increases the strain
of holding the tool and results in loss of speed.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
FEEDING TOO FAST
See Figure 18.
Clean, smooth routing and edge shaping can be done only
when the bit is revolving at a relatively high speed and is
taking very small bites to produce tiny, cleanly severed chips.
If you force the router to move forward too fast, the RPM of
the bit becomes slower than normal in relation to its forward
movement. As a result, the bit must take bigger bites as it
revolves. Bigger bites mean bigger chips and a rougher
finish. Also, because bigger bites require more power, the
router motor may become overloaded.
TOO FAST
Fig. 18
Under extreme force-feeding conditions, the relative RPM
of the bit can become so slow—and the bites it has to take
so large—that chips will be partially knocked off (rather
than fully cut off). This causes splintering and gouging of
the workpiece.
The router is an extremely high-speed tool, and will make
clean, smooth cuts if allowed to run freely without the over-
load of a forced feed. You can always detect force feeding
by the sound of the motor. Its high-pitched whine will sound
lower and stronger as it loses speed. Also, the strain of hold-
ing the tool will be noticeably increased.
FEEDING TOO SLOWLY
See Figure 19.
TOO SLOW
It is possible to spoil a cut by moving the router forward too
slowly. When you advance the router into the work too slowly,
the revolving bit does not dig into new wood fast enough
to take a bite; instead, it merely scrapes away sawdust-like
particles. Scraping produces heat, which can glaze, burn,
or mar the cut and in extreme cases, can overheat the bit,
destroying its hardness.
Fig. 19
When the bit is scraping instead of cutting, controlling the
router is more difficult. With practically no load on the mo-
tor, the bit revolves at close to top RPM, and has a much
greater than normal tendency to bounce off the sides of
the cut (especially if the wood has a pronounced grain with
hard and soft areas). As a result, the cut produced may have
rippled, instead of straight, sides.
Feeding too slowly can also cause the router to take off in a
wrong direction from the intended line of cut. Always grasp
and hold the router firmly with both hands when routing.
You can detect when you are feeding the router too slowly by
the runaway, high-pitched sound of the motor or by feeling
the wiggle of the bit in the cut.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DEPTH
OF CUT
DEPTH OF CUT
See Figures 20 - 21.
Depth of cut is important because it affects the rate of feed
that, in turn, affects the quality of the cut and the possibility
of damage to the tool’s motor and bit.
WIDTH OF CUT
A deep cut requires a slower feed than a shallow one. A cut
that is too deep will slow the feed so that the bit is scraping
rather than cutting. A too deep cut can cause smaller bits
to be broken off. Bits that are 1/16 in. in diameter are easily
broken off when subjected to too much side thrust. A large
enough bit is not likely to break, but attempting a cut that
is too deep may result in a rough cut, and it may be difficult
to guide and control the bit as desired. It is recommended
that you do not exceed 1/8 in. depth of cut in a single pass,
regardless of the bit size or the softness or condition of the
workpiece.
Fig. 20
2ND
PASS
1ST
PASS
1ST
PASS
2ND
PASS
To make deeper cuts, make as many successive passes as
needed, lowering the bit 1/8 in. for each new pass. To save
time, perform all the cutting necessary at one depth setting
before lowering the bit for the next pass. This will insure a
uniform depth when you complete the final pass.
Fig. 21
NOTE: Do not remove more than 1/8 in. in a single pass.
Excessive depth of cut can result in loss of control and the
possibility of serious personal injury.
ADJUSTMENTS
LOCK LEVER
ADJUSTING LOCK LEVER TENSION ON THE
STOP NUT
FIXED BASE AND PLUNGE BASE ROUTER
See Figure 22.
Over time and with repeated use, the lock lever may become
loose. When this occurs, tighten the stop nut slightly. The
elasticstopnutshouldbelooseenoughsothatthereissome
play in the lock lever when it is in the open position.
NOTE: Do not over tighten the elastic stop nut. The lock lever
should clamp tightly to secure the motor housing.
CAUTION:
Make sure the motor housing does not move
up or down when clamped. If motor is not
securely clamped in base, adjustments will not
be accurate.
TO
TIGHTEN
Fig. 22
REAR VIEW
WARNING:
ROUTER TABLE ATTACHMENT
Follow the provided proper instructions when
mounting router to a routing table. Failure to use
router tables with appropriate safety features could
result in serious personal injury. Use router tables
that are UL classified and identified suitable for use
with the specific router model.
See Figure 23.
When attaching the router to a routing table, remove the
subbase, and use the router table attachment screws pro-
vided with the router. Use these screws to replace the sub-
base screws shown in figure 23.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
CENTERING TOOL
See Figure 23.
CONE
If the subbase needs to be replaced, removed, or changed,
a centering tool is provided. The centering tool is double
sided to center the subbase when using the 1/2 in. or 1/4
in. collet.
SUBBASE
SCREWS
PIN
To remove the subbase on the router:
Unplug the router.
COLLET
NUT
Loosen the subbase screws on the base.
Remove the router subbase.
SUBBASE
To install the centering tool and subbase:
Unplug the router.
Insert the subbase screws on the base.
Tighten screws lightly so that the subbase can move
freely.
Using the supplied wrench, hold the collet nut with one
wrench or depress and hold the spindle lock until it locks
into place.
Loosen the collet nut.
SUBBASE
SCREWS
Insert the centering tool pin into the collet and tighten the
collet securely with the wrench provided.
Release the spindle lock if necessary.
Place the cone on the pin and lightly press down on the
cone until it stops as shown in figure 23. This will center
the subbase.
SPINDLE
LOCK
SUBBASE
SCREWS
While pressing down on the cone, tighten the subbase
screws.
To remove the centering tool:
Unplug the router.
Using the supplied wrench, hold the collet nut with one
wrench or depress and hold the spindle lock until it locks
into place.
Fig. 23
Loosen the collet nut and remove the centering tool.
Release the spindle lock if necessary.
ATTACHING/REMOVING VACUUM
VACUUM
ADAPTOR
SCREWS
ADAPTORS
See Figure 24.
VACUUM
ADAPTOR
The provided vacuum adaptors provide dust free routing.
To attach/remove the vacuum adaptor to the plunge
base:
SCREW
HOLES
Unplug the router.
Remove the vacuum adaptor screws on the subbase by
turning counterclockwise.
Place the plunge base vacuum adaptor on the plunge
base with the screw openings lined up with the screw
holes on the bottom of the subbase.
Reinsert vacuum adaptor screws.
Turn clockwise to tighten.
To remove, turn screws counterclockwise.
To attach/remove the vacuum adaptor to the fixed
base:
SCREW
HOLES
Unplug the router.
VACUUM
ADAPTOR
SCREWS
Using the supplied screws, place the fixed base vacuum
adaptor on the fixed base with the openings in the vacuum
adaptor lined up with the screw holes on the back of the
base.
Insert the supplied vacuum adaptor screws.
Turn screws clockwise with a screwdriver to tighten.
To remove, turn screws counterclockwise.
VACUUM
ADAPTOR
Fig. 24
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Electric tools used on fiberglass material, wallboard, spack-
ling compounds, or plaster are subject to accelerated wear
and possible premature failure because the fiberglass chips
and grindings are highly abrasive to bearings, brushes,
commutators, etc. Consequently, we do not recommended
using this tool for extended work on these types of materials.
However, if you do work with any of these materials, it is ex-
tremely important to clean the tool using compressed air.
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses with
side shields during power tool operation or when
blowing dust. If operation is dusty, also wear a
dust mask.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
GENERAL MAINTENANCE
CLEANING THE BITS
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
Get faster more accurate cutting results by keeping
bits clean and sharp. Remove all accumulated pitch and
gum from bits after each use. When sharpening bits, sharpen
only the inside of the cutting edge. Never grind the outside
diameter. When sharpening the end of a bit, be sure to grind
the clearance angle the same as originally ground.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
CLEANING THE COLLET
From time to time, it becomes necessary to clean the collet
and collet nut. To do so, simply remove collet nut from collet
and clean the dust and chips that have collected. Then return
collet nut to its original position.
ACCESSORIES
Look for these accessories at your local home center:
Edge Guide Assembly*....................Part no. 300869006
Dovetail Joint Template Kit
Butt Hinge Template Set
Router Guide Bushing Kit
Plunge Depth Adjustment
Knob Extension*...............................Part no. 200438001
* Available through customer service only. Call 1-866-539-1710 to order.
COMBINATION
PANEL
V-GROOVE
CHAMFER
STRAIGHT
FACE
COMBINATION
STRAIGHT/BEVEL
BIT
HINGE
MORTISING
BIT
DOVETAIL
BIT
VEINING
BIT
CORE
BOX
BIT
BIT
BIT
WARNING:
Current attachments and accessories available for use with this tool are listed above. Do not use any attachments
or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not
recommended can result in serious personal injury.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL
3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting
warranty service.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at
retail and may not be transferred. This warranty only covers
defects arising under normal usage and does not cover any
malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than
an authorized service center for RIDGID® branded hand
held and stationary power tools. Consumable accessories
provided with the tool such as, but not limited to, blades,
bits and sand paper are not covered.
Limited to RIDGID® hand held and stationary power tools
purchased 2/1/04 and after. This product is manufactured
by One World Technologies, Inc. The trademark is licensed
from RIDGID, Inc. All warranty communications should be
directed to One World Technologies, Inc., attn: RIDGID Hand
Held and Stationary Power Tool Technical Service at (toll
free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are
dissatisfied with the performance of this RIDGID® Hand Held
and Stationary Power Tool for any reason you may return
the tool to the dealer from which it was purchased for a full
refund or exchange. To receive a replacement tool you must
present proof of purchase and return all original equipment
packaged with the original product. The replacement tool
will be covered by the limited warranty for the balance of
the 3 YEAR service warranty period.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC.
MAKE NO WARRANTIES, REPRESENTATIONS OR
PROMISES AS TO THE QUALITY OR PERFORMANCE
OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI-
CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied
warranties, including warranties of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE, are disclaimed.
Any implied warranties, including warranties of merchant-
ability or fitness for a particular purpose, that cannot be
disclaimed under state law are limited to three years from the
date of purchase. One World Technologies, Inc. and RIDGID,
Inc. are not responsible for direct, indirect, incidental or
consequential damages. Some states do not allow
limitations on how long an implied warranty lasts and/or
do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state
to state.
WHAT IS COVERED UNDER THE 3 YEAR
LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power
Tools covers all defects in workmanship or materials and
normal wear items such as brushes, chucks, motors, switch-
es, cords, gears and even cordless batteries in this RIDGID®
tool for three years following the purchase date of the tool.
Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it;
freight prepaid, or take it in to an authorized service center
for RIDGID® branded hand held and stationary power tools.
You may obtain the location of the authorized service cen-
ter nearest you by calling (toll free) 1-866-539-1710 or by
logging on to the RIDGID® website at www.ridgid.com.
When requesting warranty service, you must present the
original dated sales receipt. The authorized service center will
repair any faulty workmanship, and either repair or replace
any part covered under the warranty, at our option, at no
charge to you.
One World Technologies, Inc.
Hwy. 8
Pickens, SC 29671
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
ROUTER
WITH FIXED AND PLUNGE BASES
DOUBLE INSULATED
R2900
Customer Service Information:
For parts or service, contact your nearest RIDGID authorized service center. Be
sure to provide all relevant information when you call or visit. For the location of
the authorized service center nearest you, please call 1-866-539-1710 or visit us
The model number of this tool is found on a plate attached to the motor housing.
Please record the serial number in the space provided below. When ordering repair
parts, always give the following information:
R2900
Model No.
Serial No.
983000-786
02-08-06 (REV:02)
Download from Www.Somanuals.com. All Manuals Search And Download.
|