®
Instant Wireless Series
Dual-Band Wireless
A+G Broadband Router
Use this guide to install:
WRT55AG
User Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Note: Combinations of power levels and antennas resulting in a radiated power level of
above 100 mW equivalent isotropic radiated power (EIRP) are considered as not com-
pliant with the above mentioned directive and are not allowed for use within the European
community and countries that have adopted the European R&TTE directive 1999/5/EC
and/or the CEPT recommendation Rec 70.03.
Table of Contents
Chapter 1: Introduction
The Dual-Band Wireless A+G Broadband Router
Features
The Router’s Functions
IP Addresses
Router Setup Overview
1
1
2
2
3
4
For more details on legal combinations of power levels and antennas, contact Linksys
Corporate Compliance.
•
Linksys Group vakuuttaa täten että Instant Wireless Dual-Band A+G Broadband
Router tyyppinen laite on direktiivin 1999/5/EY, direktiivin 89/336/EEC ja direktiivin
73/23/EEC oleellisten vaatimusten ja sitä koskevien näiden direktiivien muiden ehto-
jen mukainen.
•
•
Linksys Group déclare que la Instant Wireless Dual-Band A+G Broadband Router
est conforme aux conditions essentielles et aux dispositions relatives à la directive
1999/5/EC, la directive 89/336/EEC, et à la directive 73/23/EEC.
Belgique B L'utilisation en extérieur est autorisé sur le canal 11 (2462 MHz), 12 (2467
MHz), et 13 (2472 MHz). Dans le cas d'une utilisation privée, à l'extérieur d'un bâti-
ment, au-dessus d'un espace public, aucun enregistrement n'est nécessaire pour
une distance de moins de 300m. Pour une distance supérieure à 300m un enreg-
istrement auprès de l'IBPT est requise. Pour une utilisation publique à l'extérieur de
bâtiments, une licence de l'IBPT est requise. Pour les enregistrements et licences,
veuillez contacter l'IBPT.
Chapter 2: Getting to Know the Dual-Band
Wireless A+G Broadband Router
The Router’s Back Panel
6
6
7
The Router’s Front Panel
Chapter 3: Connect the Router
Overview
Wired Connection to a PC
Wireless Connection to a PC
10
10
10
12
•
France F:
2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respec-
tivement) sont complétement libres d'utilisation en France (en utilisation intérieur).
Pour ce qui est des autres canaux, ils peuvent être soumis à autorisation selon le
départment. L'utilisation en extérieur est soumis à autorisation préalable et très
restreint.
5 GHz Bande: Conformément aux décisions de la CEPT, l'utilisation des fréquences
de la bande 5150 MHz - 5350 MHz est autorisée à l'intérieur des bâtiments avec une
puissance maximale de 200 mW, et interdite en extérieur. La bande 5470 MHz - 5725
MHz n'est pas ouverte aujourd'hui.
Vous pouvez contacter l'Autorité de Régulation des Télécommunications
Chapter 4: Configure the PCs
Overview
Configuring Windows 98 and Millennium PCs
Configuring Windows 2000 PCs
Configuring Windows XP PCs
13
13
14
16
18
2.4 GHz Band: only channels 10, 11, 12, 13 (2457, 2462, 2467, and 2472 MHz
respectively) may be used freely in France for indoor use. License required for out-
door installations.
Chapter 5: Setting Up the Dual-Band
Wireless A+G Broadband Router
20
28
5 GHz Band: frequencies in the 5150 MHz - 5350 MHz band may be used indoor
with maximum power of 200 mW. Their use is forbidden outdoors. The 5470 MHz -
5725 MHz band is not currently open.
Chapter 6: Configure the Router’s Basic
Settings with the Web-based Utility
•
•
•
Deutschland D: Anmeldung im Outdoor-Bereich notwending, aber nicht genehmi-
gungspflichtig. Bitte mit Händler die Vorgehensweise abstimmen.
Germany D: License required for outdoor installations. Check with reseller for proce-
dure to follow.
Italia I: E' necessaria la concessione ministeriale anche per l'uso interno. Verificare
con i rivenditori la procedura da seguire. L'uso per installazione in esterni non e' per-
messa.
Italy I: License required for indoor use. Use with outdoor installations not allowed.
The Netherlands NL License required for outdoor installations. Check with reseller for
procedure to follow.
Nederlands NL Licentie verplicht voor gebruik met buitenantennes. Neem contact op
met verkoper voor juiste procedure.
Chapter 7: The Router’s Web-based Utility
Overview
How to Access the Web-based Utility
Setup
Security
System
DHCP
SNMP
Status
33
33
33
34
44
46
50
52
53
•
•
•
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Chapter 1: Introduction
The Dual-Band Wireless A+G Broadband Router
Help
55
56
56
60
63
66
68
Advanced Tabs
Advanced Wireless
Internet Filter
Port Forwarding
Routing
The Dual-Band Wireless A+G Broadband Router is like four devices in one
box! The Router function lets you securely share one high-speed Internet con-
nection among your entire network, while the 4-port full duplex 10/100 Switch
jump-starts your wired-Ethernet network. Connect four PCs directly, or daisy-
chain out to more hubs and switches to create as big a network as you need.
DDNS
The Dual-Band Wireless A+G Broadband Router also contains two Wireless
Access Points, supporting all three wireless networking specifications. The
first Access Point uses the 2.4GHz radio band, supporting both the popular and
inexpensive Wireless-B (802.11b) standard at 11Mbps, and the new, almost
five times faster, Wireless-G (draft 802.11g) at 54Mbps. The second Access
Point radio operates in the 5GHz band, and supports Wireless-A (802.11a) net-
working, also at 54Mbps. Since the two radios operate in different bands, they
can work simultaneously, blanketing your wireless zone with bandwidth.
Appendix A: Troubleshooting
Common Problems and Solutions
Frequently Asked Questions
70
70
81
Appendix B: How to Ping Your ISP’s E-mail &
Web Addresses
89
Appendix C: Configuring Wireless Security
Background
WEP Encryption
92
92
93
To protect your data and privacy, the Dual-Band Wireless A+G Broadband
Router can encrypt all wireless transmissions. The MAC Address filter lets
you decide exactly who has access to your wireless network. The Router also
serves as a DHCP Server, has NAT technology to protect against Internet
intruders, DMZ capability, supports VPN pass-through, and can be configured
to filter internal users' access to the Internet. Configuration is a snap with the
web browser-based configuration utility.
Appendix D: Finding the MAC Address and IP
Address for Your Ethernet Adapter
94
97
Appendix E: Glossary
Appendix F: Specifications
Environmental
113
114
With the Linksys Dual-Band Wireless A+G Broadband Router at the center of
your home or office network, you can share a high-speed Internet connection,
files, printers, and multi-player games with the flexibility, speed, and security
you need!
Appendix G: Warranty Information
Appendix H: Contact Information
115
116
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Remember that the Router’s ports connect to two sides. The 10/100 LAN ports
connect to the LAN, and the Internet port connects to the Internet. The LAN
ports transmit data at 10 Mbps or 100 Mbps, and the broadband port, or
Internet port, transmits data at 10/100 Mbps. Your wireless devices connect to
the Router through either 802.11a, 802.11b, or draft-802.11g wireless technol-
ogy.
Features
•
Dual-band, tri-standard Access Point communicates with Wireless-A
(802.11a), Wireless-B (802.11b), and Wireless-G (draft 802.11g) wireless
networks
•
•
Protect your wireless investment while preparing your infrastructure for the
future
Built-in 4-port Switch jump-starts your wired network, while the Router
functionality securely shares your high-speed Internet connection with
wired and wireless computers
IP Addresses
What’s an IP Address?
IP stands for Internet Protocol. Every device on an IP-based network, including
PCs, print servers, and routers, requires an IP address to identify its “location,” or
address, on the network. This applies to both the Internet and LAN connections.
There are two ways of assigning an IP address to your network devices.You can
assign static IP addresses or use the Router to assign IP addresses dynamically.
•
•
Advanced Security: Wireless data encryption (WEP), VPN pass-through,
Internet access control and Wireless filters
Performance Investment Protection: Compatibility with Wireless-A
(802.11a), Wireless-B (802.11b) and Wireless-G Standards
Built-in 4-Port 10/100 Switch Supports Wired Ethernet Clients
All Ethernet Ports Support Auto-MDI/MDI-X -- No Need for Crossover
Cables or Uplink Port
•
•
Note: Since the Router uses NAT technology, the only IP address that
can be seen from the Internet for your network is the Router’s Internet
IP address.
•
•
Wireless Security with up to 152-bit WEP Encryption
Enhanced Security Management Functions: Port Filtering, MAC and IP
Address Filtering, DMZ Hosting, and NAT Technology
Access Your Corporate Network Remotely through Virtual Private
Networking (VPN) -- Supports IPSec and PPTP Pass-Through
Easily Configurable through a Web Browser -- Locally and over the Internet
DDNS and DHCP Server Capability to Assign IP Addresses Automatically
Supports Static and Dynamic Routing (RIP1 and 2)
However, even this Internet IP address can be blocked, so that the
Router and network seem invisible to the Internet—see the Block
WAN Requests description under Filters in “Chapter 7: The Router’s
Web-based Utility.”
•
•
•
•
Static IP Addresses
A static IP address is a fixed IP address that you assign manually to a PC or
other device on the network. Since a static IP address remains valid until you
disable it, static IP addressing ensures that the device assigned it will always
have that same IP address until you change it. Static IP addresses must be
unique and are commonly used with network devices such as server PCs or
print servers.
The Router’s Functions
Simply put, a router is a network device that connects two networks together. A
wireless router connects three networks.
In this instance, the Router connects your wired network and wireless network,
or the group of PCs in your home or office, to the Internet. The Router process-
es and regulates the data that travels between these networks.
If you use the Router to share your cable or DSL Internet connection, contact
your ISP to find out if they have assigned a static IP address to your account.
If so, you will need that static IP address when configuring the Router. You can
get that information from your ISP.
The Router’s NAT feature protects your network of PCs so users on the public,
Internet side cannot “see” your PCs. This is how your network remains private.
The Router protects your network by inspecting every packet coming in
through the Internet port before delivery to the appropriate PC on your net-
work. The Router inspects Internet port services like the web server, ftp server,
or other Internet applications, and, if allowed, it will forward the packet to the
appropriate PC on the LAN side.
Dynamic IP Addresses
A dynamic IP address is automatically assigned to a device on the network,
such as PCs and print servers. These IP addresses are called “dynamic”
because they are only temporarily assigned to the PC or device. After a certain
time period, they expire and may change. If a PC logs onto the network (or the
Internet) and its dynamic IP address has expired, the DHCP server will auto-
matically assign it a new dynamic IP address.
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
• Chapter 5: Setting up the Dual-Band Wireless A+G Broadband Router
This chapter will walk you through the Setup Wizard included on the Setup
CD-ROM.
DHCP (Dynamic Host Configuration Protocol) Servers
PCs and other network devices using dynamic IP addressing are assigned a new
IP address by a DHCP server. The PC or network device obtaining an IP
address is called the DHCP client. DHCP frees you from having to assign IP
addresses manually every time a new user is added to your network.
• Chapter 6: Configuring the Router’s Basic Settings with the Web-based
Utility
While you should always use the Setup Wizard when setting up the Router,
more advanced users may wish to do this through the Web-based Utility. This
chapter shows you how to configure the Router’s basic settings this way.
A DHCP server can either be a designated PC on the network or another net-
work device, such as the Router. By default, the Router’s DHCP Server func-
tion is enabled.
If you already have a DHCP server running on your network, you must disable
one of the two DHCP servers. If you run more than one DHCP server on your
network, you will experience network errors, such as conflicting IP addresses.
To disable DHCP on the Router, see the DHCP section in “Chapter 7: The
Router’s Web-based Utility.”
Notebook with
Wireless Adapter
Notebook with
Wireless Adapter
Note: Even if you assign a static IP address to a PC, other PCs can
still use DHCP’s dynamic IP addressing, as long as the static IP
address is not within the DHCP range of the LAN IP Addresses.
If the dynamic IP addressing fails to provide a dynamic IP address,
refer to “Appendix A: Troubleshooting.”
Router Setup Overview
Cable or DSL Modem
Router
This User Guide covers the steps for setting up a network with the Router. After
going through “Chapter 2: Getting to Know the Dual-Band Wireless A+G
Broadband Router,” most users will only need to use the following chapters:
PC with
Ethernet
Adapter
Figure 1-1
• Chapter 3: Connect the Router
This chapter instructs you on how to connect a cable or DSL modem to the
Router and connect your PC(s) to the Router.
• Chapter 7: The Router’s Web-based Utility
The Web-based Utility controls all of the Router’s functions and settings. This
chapter shows you how to use this Utility.
• Chapter 4: Configure the PCs
This chapter instructs you on how to configure your PCs to be DHCP clients,
if you have previously set static IP addresses on your PCs.
When you’re finished with these basic steps, you will be ready to connect to the
Internet. You can also modify the Router’s settings further; for example, you
can adjust security features and other settings to enable online gaming (see
“Chapter 7: The Router’s Web-based Utility”).
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
The Reset Button
Chapter 2: Getting to Know the
The Reset button can be used in one of two ways:
Dual-Band Wireless A+G
Broadband Router
1. If the Router is having problems connecting to the Internet, press the Reset
button for just a moment with a paper clip or a pencil tip. This clears up any
jammed connections, and is similar to pressing the Reset button on your PC
to reboot it.
The Router’s Back Panel
This will reboot the Router while keeping all of the Router’s settings.
The Router’s ports, shown in Figure 2-1, are located on the Router’s back panel.
2. If you are experiencing extreme problems with the Router and have tried all
other troubleshooting measures, press the Reset Button and hold it down for
10 seconds.
This will restore factory defaults and clear all of the Router’s settings,
including settings such as a new password or wireless settings.
The Router’s Front Panel
The Router’s LEDs, shown in Figure 2-2, display information about the
Router’s status.
Figure 2-1
Internet
The Internet port is where you connect your cable or DSL
modem through an Ethernet network cable. Your modem
connection will not work from any other port.
Ports 1-4
These four LAN (Local Area Network) ports connect to net-
work devices, such as PCs, print servers, and network
attached storage (NAS). Each of the ports will auto-detect
whether a straight-through or crossover cable is plugged into
it, so there is no need for an uplink port. Any one of the four
ports can serve as an uplink port to other network devices.
Figure 2-2
Power
Diag
Green. The Power LED lights up when the Router is powered
on.
Red. The Diag LED lights up when the Router goes through
its self-diagnosis mode during every boot-up. It will turn off
upon successful completion of the diagnosis.
Power
The Power port is where you will connect the power adapter.
If this LED stays on for one minute or longer, see “Appendix
A: Troubleshooting.”
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
The 802.11a WLAN Indicators
The Internet Indicators
Link/Act
Green. The Link/Act LED lights up when a successful con-
Act
Green. When the Act LED flickers, the 802.11a wireless net-
nection is made between the Router and your cable or DSL
modem (the Internet). The Link/Act LED flickers when the
Router is sending or receiving data over the Internet port.
work is active.
Link
Green. When the Link LED is continuously lit, the 802.11a
wireless network is available.
100
Orange. The 100 LED lights up when a successful 100Mbps
connection is made through the corresponding port.
The 802.11b WLAN Indicators
If this LED does not light up, then your connection speed is
10Mbps.
Act
Green. When the Act LED flickers, the 802.11b wireless net-
work is active.
Link
Green. When the Link LED is continuously lit, the 802.11b
Proceed to “Chapter 3: Connect the Router.”
wireless network is available.
The LAN Indicators
Link/Act
Full/Col
Green. The Link/Act LED serves two purposes. If the LED
is continuously lit, the Router is successfully connected to a
device through the corresponding port. If the LED is flicker-
ing, the Router is actively sending or receiving data over that
port.
Green. The Full/Col LED also serves two purposes. If this
LED is lit up solidly, the connection made through the corre-
sponding port is running in Full Duplex mode. If the LED
flickers, the connection is experiencing collisions (when two
PCs send data at the same time). Infrequent collisions are
normal.
100
Orange. The 100 LED lights up when a successful 100Mbps
connection is made through the corresponding port.
If this LED does not light up, then your connection speed is
10Mbps.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
3. Connect a different Ethernet network
cable from your cable or DSL modem
to the Internet port on the Router’s rear
panel. This is the only port that will
work for your modem connection.
Chapter 3: Connect the Router
Overview
Note: These directions on connecting the Router are provided only
to help when you are making the connections. If you are using the
Setup Wizard, make your connections only when the Wizard asks.
Figure 3-2
The Router’s setup consists of more than simply plugging hardware together.
You will have to configure your networked PCs to accept the IP addresses that
the Router assigns them (if applicable), and you will also have to configure the
Router with setting(s) provided by your Internet Service Provider (ISP).
4. Power on the cable or DSL modem.
5. Connect the power adapter to the
Router’s Power port, and then plug the
power adapter into a power outlet.
The installation technician from your ISP should have left the setup informa-
tion for your modem with you after installing your broadband connection. If
not, you can call your ISP to request that data.
Note: You should always plug
the Router’s power adapter into
a power strip with surge pro-
tection.
Once you have the setup information you need for your specific type of Internet
connection, you can begin installation and setup of the Router.
Figure 3-3
If you want to use a PC with an Ethernet adapter to configure the Router, go to
“Wired Connection to a PC and Boot-Up.” If you want to use a PC with a wire-
less adapter to configure the Router, go to “Wireless Connection to a PC and
Boot-Up.”
The Power LED on the front panel will light up green as soon as the power
adapter is connected properly.
Wired Connection to a PC
The Diag LED will light up red for a few seconds. It will turn off when the self-
test is complete. If this LED stays on for one minute or longer, see “Appendix
A: Troubleshooting.”
1. Before you begin, make sure that all of
your network’s hardware is powered
off, including the Router, PCs, and
cable or DSL modem.
6. Power on one of your PCs.
Have you checked that the Link/Act LEDs for all your LAN con-
nections and the Link LED for your Internet connection light up?
2. Connect one end of an Ethernet net-
work cable to one of the LAN ports
(labeled 1-4) on the back of the
Router, and the other end to an
Ethernet port on a PC.
If all of your Link LEDs are not lighting up, make sure that all your
cables are securely plugged in, and that all of your hardware is pow-
ered on properly. Verify that the modem is plugged into the Internet
port on the Router.
Figure 3-1
Repeat this step to connect more PCs, a switch, or other network devices to
the Router.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Wireless Connection to a PC
Chapter 4: Configure the PCs
If you want to use a wireless connection to access the Router, follow these
instructions:
Overview
The instructions in this chapter will help you configure each of your comput-
ers to be able to communicate with the Router.
1. Before you begin, make sure that all of your network’s hardware is powered
off, including the Router, PCs, and cable or DSL modem.
To do this, you need to configure your PC’s network settings to obtain an IP (or
TCP/IP) address automatically, so your PC can function as a DHCP client.
Computers use IP addresses to communicate with the Router and each other
across a network, such as the Internet.
2. Connect an Ethernet network cable
from your cable or DSL modem to the
Internet port on the Router’s rear
panel, as shown in Figure 3-4. This is
the only port that will work for your
modem connection.
First, find out which Windows operating system your computer is running. You
can find out by clicking the Start button. Read the side panel of the Start menu
to find out which operating system your PC is running.
3. Power on the cable or DSL modem.
Figure 3-4
You may need to do this for each computer you are connecting to the Router.
4. Connect the power adapter to the Power port, and then plug the power
adapter into a power outlet.
The next few pages tell you, step by step, how to configure your network set-
tings based on the type of Windows operating system you are using. Make sure
that an Ethernet or wireless adapter (also known as a network adapter) has been
successfully installed in each PC you will configure. Once you’ve configured
your computers, setup the Router, either by using the Setup Wizard as shown
in “Chapter 5: Setting Up the Dual-Band Wireless A+G Broadband Router” or
by using the Web-based Utility as shown in “Chapter 6: Configuring the
Router’s Basic Settings with the Web-based Utility”.
Note:You should always plug the Router’s power adapter into a power
strip with surge protection.
• The Power LED on the front panel will light up green as soon as the power
adapter is connected properly.
• The Diag LED will light up red for a few seconds and turn off when the self-
test is complete. If this LED stays on for one minute or longer, see “Appendix
A: Troubleshooting.”
Important: By default Windows 98, 2000, Me, and XP has
TCP/IP installed and set to obtain an IP address automatically.
4. Power on one of the PCs on your wireless network(s).
If your PC does not have TCP/IP installed, click Start and then
Help. Search for the keyword TCP/IP. Then follow the instruc-
tions to install TCP/IP.
5. For initial access to the Router through a wireless connection, make sure the
PC’s wireless adapter has its SSID set to linksys-a or linksys-g (which are
the Router’s default SSID settings, depending upon the wireless devices you
are using), and its WEP encryption is disabled. After you have accessed the
Router, you can change the Router and this PC’s adapter settings to match
the your usual network settings.
The Router’s hardware installation is now complete.
Go to “Chapter 4: Configure the PCs.”
Note: You should always change the SSID from its default, linksys,
and enable WEP encryption.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Configuring Windows 98 and Millennium PCs
Dual-Band Wireless A+G Broadband Router
3. Click the IP Address tab. Select Obtain an IP address automatically.
1. Click the Start button. Select Settings and click the Control Panel icon.
Double-click the Network icon.
2. On the Configuration tab, select the TCP/IP line for the applicable
Ethernet adapter. Do not choose a TCP/IP entry whose name mentions
DUN, PPPoE, VPN, or AOL. If the word TCP/IP appears by itself, select
that line. Click the Properties button.
Figure 4-2
4. Now click the Gateway tab, and verify that the Installed Gateway field is
blank. Click the OK button.
5. Click the OK button again. Windows may ask you for the original Windows
installation disk or additional files. Check for the files at
c:\windows\options\cabs, or insert your Windows CD-ROM into your CD-
ROM drive and check the correct file location, e.g., D:\win98, D:\win9x,
etc. (if “D” is the letter of your CD-ROM drive).
Figure 4-1
6. Windows may ask you to restart your PC. Click the Yes button. If Windows
does not ask you to restart, restart your computer anyway.
Go to “Chapter 5: Setting Up the Dual-Band Wireless A + G Broadband
Router.”
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight
Configuring Windows 2000 PCs
Internet Protocol (TCP/IP), and click the Properties button.
1. Click the Start button. Select Settings and click the Control Panel icon.
Double-click the Network and Dial-up Connections icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter
(usually it is the first Local Area Connection listed). Double-click the
Local Area Connection. Click the Properties button.
Figure 4-4
4. Select Obtain an IP address automatically. Once the new window
appears, click the OK button. Click the OK button again to complete the
PC configuration.
Figure 4-3
Figure 4-5
5. Restart your computer.
Go to “Chapter 5: Setting Up the Dual-Band Wireless A + G Broadband
Router.”
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight
Configuring Windows XP PCs
Internet Protocol (TCP/IP), and click the Properties button.
The following instructions assume you are running Windows XP with the
default interface. If you are using the Classic interface (where the icons and
menus look like previous Windows versions), please follow the instructions for
Windows 2000.
1. Click the Start button and then the Control Panel icon. Click the Network
and Internet Connections icon. Then click the Network Connections
icon.
2. Select the Local Area Connection icon for the applicable Ethernet adapter
(usually it is the first Local Area Connection listed). Double-click the
Local Area Connection. Click the Properties button.
Figure 4-7
4. Select Obtain an IP address automatically. Once the new window
appears, click the OK button. Click the OK button again to complete the
PC configuration.
Figure 4-6
Figure 4-8
5. Restart your computer.
Go to “Chapter 5: Setting Up the Dual-Band Wireless A + G Broadband
Router.”
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Chapter 5: Setting Up the Dual-Band
Wireless A + G Broadband Router
Dual-Band Wireless A+G Broadband Router
3. As shown in Figure 5-2, you will need to have your PC connected to an
active Internet connection. The Setup Wizard will use this connection to
detect what type of Internet access you have. Verify that you are set up cor-
rectly to your Internet connection and click the Next button to continue.
When you are ready to connect the Router to your network, the Router’s Setup
Wizard will take you through all the steps necessary for configuration.
Note: While the Router has been designed to work correctly right
out of the box, setting it up on a wireless computer will require you
to use the Linksys default settings. These settings can then be
changed with the Setup Wizard or Web-based Browser Utility.
1. Insert the Setup Wizard CD into your PC’s CD-ROM drive. Your PC must
have an active Internet connection.
2. The screen in Figure 5-1 should appear on your monitor. If it does not, this
means the autorun is not functioning. Start the Setup Wizard manually by
clicking the Start button, selecting Run, and typing d:\setup.exe (where
“D” is your PC’s CD-ROM drive). To set up the first computer connected
to the Router, click the Set Up First Computer button. When you are ready
to set up additional PCs, click the Set Up Additional Computer(s) button.
Clicking the User Guide button opened this User Guide. To exit this Setup
Wizard, click the Exit button.
Figure 5-2
4. Next, you will be asked what type of Internet connection you are using, as
shown in Figure 5-3. Click the DSL or Cable button, whichever is appro-
priate for your type of connection.
Figure 5-1
Figure 5-3
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
5. Now, power off your modem and disconnect your Internet connection.
Then, connect the Router as shown on the screen displayed. If you have a
cable connection, you will see a screen similar to that shown in Figure 5-4.
If you have a DSL connection, you will see a screen similar to that shown
in Figure 5-5. When the connections are made, click the Next button to con-
tinue.
6a. While making your
Internet connection,
the Router will
require you to Log
in, as shown in
Figure 5-8. Enter the
default password:
admin. Then, click
the OK button. (This
password should be
changed from the
Web-based Utility’s
Password tab for
greater security.)
Figure 5-8
Figure 5-4
Figure 5-5
Note: After the Router is connected, your PC may try to connect directly
to the Internet. Since the connection will now be made through the Router,
you can disregard (click Cancel) any attempt your PC makes to connect.
7a. When connecting to the Internet
through a Static IP Address:
6. Power on your modem and connect the power to the modem and the Router.
As shown on the following screen, verify that the Router’s LEDs are cor-
rectly lit. If you have a cable connection, you will see a screen similar to
that shown in Figure 5-6. If you have a DSL connection, you will see a
screen similar to that shown in Figure 5-7. When the LEDs are lit appro-
priately, click the Next button to continue.
The Setup Wizard will now ask
you to make changes to your PC’s
TCP/IP settings. Follow the
instructions shown, clicking the
Next button to continue.
If you are using Windows 98 or
Me, the instructions will start as
shown in Figure 5-9.
Figure 5-9
Figure 5-6
Figure 5-7
If you are using a Static IP Address to connect to the Internet, proceed to
step 7a. If you are using a DHCP connection, proceed to step 7b. If you are
using a PPPoE connection, proceed to step 7c.
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
If you are using Windows 2000,
the instructions will start as
shown in Figure 5-10.
7b. When connecting to the Internet through a DHCP connection:
If you have a cable connection, you will see a screen similar to that shown
in Figure 5-14. If you have a DSL connection, you will see a screen similar
to that shown in Figure 5-15. Enter the information just as you do when
logging onto your Internet connection, and click the Next button. Then,
continue to step 6.
Figure 5-10
If you are using Windows XP, the
instructions will start as shown in
Figure 5-11. If you are using
Windows XP in “Classic” mode,
you can see these instructions in
this mode by clicking the Classic
button.
Figure 5-14
Figure 5-15
7c. When connecting to the Internet through a PPPoE connection:
PPPoE connections are only available with DSL Internet connections. If
this is how you connect to the Interent, you will see a screen similar to that
shown in Figure 5-16. Enter the information just as you do when logging
onto your Internet connection, and click the Next button. Then, continue to
step 6.
Figure 5-11
After configuring your PC, as shown in the first part of 5a, you will see a
Static IP Setup screen. If you have a cable connection, you will see a screen
similar to that shown in Figure 5-12. If you have a DSL connection, you
will see a screen similar to that shown in Figure 5-13. Enter the informa-
tion just as you do when logging onto your Internet connection, and click
the Next button. Then, continue to step 6.
Figure 5-16
Figure 5-12
Figure 5-13
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
8. As shown in Figure 5-17, the Basic Settings screen for your 2.4GHz/54g
(802.11g-draft) wireless products will appear. Enter the Network Mode,
SSID, and the channel at which the network broadcasts its wireless signal.
Then, click the Next button to continue.
9. As shown in Figure 5-18, the Basic Settings screen for your 5 GHz/802.11a
wireless products will appear. Enter your wireless network’s SSID and
select the channel at which the network broadcasts its wireless signal. Then,
click the Next button to continue.
Network Mode. Since Wireless-G products are backwards compatible with
802.11b products, this mode is provided in the event you wish to incorpo-
rate 802.11b products into you Wireless-G wireless network. If you are
using both Wireless-G and 802.11b products in your network, select Mixed
mode. You may experience reduced networking speeds in Mixed mode, as
the speed must compensate for both types. If you are only using Wireless-
G products in your network, select G-Only mode.
SSID. The SSID is the unique name shared among all points in a wireless
network. The SSID must be identical for all points in the wireless network.
It is case sensitive and must not exceed 32 characters, which may be any
keyboard character. The default SSID, linksys-a, should be changed for
greater security. Make sure this setting is the same for all points in your
wireless network.
Channel. Select
the appropriate
channel from
the list provided
to correspond
with your net-
work settings,
between 36 and
64. All points in
your wireless
network must
use the same
channel in order
to function cor-
SSID. The SSID is the unique name shared among all points in a wireless
network. The SSID must be identical for all points in the wireless network.
It is case sensitive and must not exceed 32 characters, which may be any
keyboard character. The default SSID, linksys-g, should be changed for
greater security. Make sure this setting is the same for all points in your
wireless network.
Channel. Select the appropriate channel from the list provided to corre-
spond with your network settings, between 1 and 11 (in North America). All
points in your wireless network must use the same channel in order to func-
tion correctly.
rectly.
Figure 5-18
10. At this point, the configura-
tion performed with the
Setup Wizard is complete, as
shown in Figure 5-19. You
can register the Router
online by clicking the
Register Online button. To
configure any other Access
Points in your network, you
can run this Setup Wizard
again. Click the Exit button
to exit the Setup Wizard.
Figure 5-17
Figure 5-19
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
3. The web-based utility will appear with the Setup tab selected. Based on the
setup instructions from your ISP, you may need to provide the Host Name
and Domain Name (usually cable ISPs require them). These fields allow
you to provide a host name and domain name for the Router and are usual-
ly left blank.
Chapter 6: Configuring the
Router’s Basic Settings with the
Web-Based Utility
The values for the Router’s LAN IP Address and Subnet Mask are shown
on the Setup screen. The default values are 192.168.1.1 for the IP Address
and 255.255.255.0 for the Subnet Mask.
This chapter will show you how to configure the Router to function in your
network and gain access to the Internet through your Internet Service Provider
(ISP). Detailed description of the Router’s web-based utility can be found in
“Chapter 7: The Router’s Web-based Utility.”
4. The Router supports four connection types: Automatic Configuration -
DHCP (obtain an IP automatically), Static IP, PPPoE, and PPTP. These
types are listed in the drop-down menu for the Configuration Type setting.
Each Setup screen and available features will differ depending on what kind
of connection type you select. Proceed to the instructions for the connec-
tion type you are using, and then continue to step 5.
The instructions from your ISP tell you how to set up your PC for Internet
access. Because you are now using the Router to share Internet access among
several computers, you will use the setup information to configure the Router
instead of your PC. You only need to configure the Router once using the first
computer you set up.
IMPORTANT: If you have previously enabled any Internet-sharing
proxy server software on any of your PCs, you must disable it now.
address) in the web
browser’s Address
field, as shown in
Figure 6-1, and
Some examples of Internet-sharing software are Internet LanBridge,
Wingate, ICS, and Sygate. To disable your Internet-sharing software:
Figure 6-1
press the Enter key.
• If you are running Netscape Navigator, click Edit, Preferences,
Advanced, and Proxies. Click Direct Connection to the Internet.
• If you are running Internet Explorer 5.x or higher, click Tools,
Settings, Control Panel, Internet Options, Connections, and
LAN Settings. Remove checkmarks from all three boxes. Click the
OK button to continue.
2. An Enter Network Password window, shown in Figure 6-2, will appear.
Windows XP users will see a Connect to 192.168.1.1 window, shown in
Figure 6-3. Leave the User Name field empty, and enter admin in lower-
case letters in the Password field
(admin is the default password).
Then, click the OK button.
You must also disable any Internet log-on software (such as Ivasion
Winpoet or Enternet 300) and any firewall software (such as
ZoneAlarm and Watchdog) on all of your PCs.
Figure 6-2
Figure 6-3
Note: For added security, you should change the password through
the Password screen of the web-based utility.
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Automatic Configuration - DHCP
PPPoE
If you are connecting through
DHCP or a dynamic IP address
from your ISP, perform these steps:
If your DSL provider says that you
are connecting through PPPoE
(you use a user name and password
to access the Internet), perform
these steps:
A. Keep the default setting,
Automatic Configuration
-
DHCP, as the Configuration
A. Select
PPPoE
as
the
Type, shown in Figure 6-4.
Configuration Type, shown in
Figure 6-6.
B. Click the Apply button to save the
setting, or click the Cancel button
to clear the setting and start over.
When you are finished, proceed to
step 5.
B. Enter the User Name.
C. Enter the Password.
Figure 6-4
D. Click the Apply button to save
the settings, or click the Cancel
Figure 6-6
Static (or Fixed) IP Address
button to clear the settings and start over. When you are finished, proceed to
step 5.
If you are connecting through a static or fixed IP address from your ISP, per-
form these steps:
Important: If you enable PPPoE, remember to remove any PPPoE
applications already installed on any of your PCs.
A. Select Static IP as the
Configuration Type, shown in
Figure 6-5.
PPTP
PPTP is a service used in Europe
only. If you are using a PPTP con-
nection, check with your ISP for the
necessary setup information.
B. Enter the Internet IP Address.
C. Enter the Subnet Mask.
D. Enter the Default Gateway.
After you have entered your setup
information, click the Apply button to
save the settings, or click the Cancel
button to clear the settings and start
over. When you are finished, proceed
to step 5.
E. Enter the DNS in the 1, 2,
and/or 3 fields. You need to
enter at least one DNS address.
F. Click the Apply button to save
the settings, or click the Cancel
button to clear the settings and
start over. When you are fin-
ished, proceed to step 5.
Figure 6-5
Figure 6-7
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
5. To configure the Router for your wireless network(s), perform these steps:
Chapter 7: The Router’s
Web-based Utility
Overview
A. To enable 5GHz, 802.11a wireless networking, make sure the 5GHz,
802.11a Enable radio button is selected. Then click the Change 5GHz
Settings button, and customize the SSID, Channel, and WEP encryption
settings as needed. Then click the Apply button to save your changes. For
more information, refer to “Chapter 7: The Router’s Web-based Utility.”
Use the Router’s web-based utility to administer it. This chapter will describe
each web page in the Utility and each page’s key functions. The utility can be
accessed via your web browser through use of a computer connected to the
Router.
Important: Operation within the 5150 to 5250GHz band is
restricted to indoor use only.
B. To enable 2.4GHz, Wireless-G wireless networking, make sure the 2.4GHz,
802.11g Enable radio button is selected. Then click the Change 2.4GHz
Settings button, and customize the SSID, Channel, and WEP encryption
settings as needed. Then click the Apply button to save your changes. For
more information, refer to “Chapter 7: The Router’s Web-based Utility.”
The Setup, Security, System, DHCP, SNMP, Status, and Help screens are avail-
able for basic setup. For advanced setup, click the Advanced tab to access these
screens: Advanced Wireless, Internet Filter, Port Forwarding, Routing, and
DDNS.
How to Access the Web-based Utility
6. If you haven’t already done so, click the Apply button to save your Setup
To access the web-based utility, launch Internet Explorer or Netscape
Navigator, and enter the
settings. Close the web browser.
Router’s default IP
address, 192.168.1.1, in
7. Restart your computers so that they can obtain the Router’s new settings.
the Address field, as
shown in Figure 7-1.
Then press Enter.
If you need more details or advanced setting information, please refer to
“Chapter 7: The Router’s Web-based Utility” or the Linksys support web-
site at support.linksys.com.
Figure 7-1
A password request page, shown in Figure 7-2 will pop up. (Windows XP users
will see a Connect to 192.168.1.1 window, shown in Figure 7-3). Leave the
User Name field blank, and enter admin (the default password) in the
Password field. Then click the OK
Figure 6-8
button.
Test the setup by opening your web browser from any computer and enter-
Congratulations! You’ve successfully configured the Router.
If you are unable to reach our website, you may want to review what you
did in this section or refer to “Appendix A: Troubleshooting.”
Proceed to “Chapter 7: The Router’s Web-based Utility” for more details
and advanced settings information.
Figure 7-2
Figure 7-3
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Automatic Configuration - DHCP
Note: For added security, you should always change the password
through the Password screen of the web-based utility.
By default, the Router’s Configuration Type is set to Automatic Configuration
- DHCP, as shown in Figure 7-4, and it should be kept only if your ISP supports
DHCP or you are connecting through a dynamic IP address.
To apply any of the settings you change on a page, click the Apply button. To
cancel any changes you’ve entered on any page, click the Cancel button. To get
additional information about any screen’s features, click the Help button.
To apply any of the settings you change on this page, click the Apply button.
To cancel any changes you’ve entered on this page, click the Cancel button. To
get more information about the features, click the Help button.
Setup
The Setup screen is the first screen you see when you access the web-based
utility. If you have already installed and set up the Router, you have already
seen this screen and properly configured all of the screen’s values.
Firmware Version This shows the version and date of the firmware you are
using. Future versions of the Router’s firmware will be posted and available
Time Zone Select your local time zone from this pull-down menu. The Router
will show the correct time for your area.
Host Name and Domain Name These fields allow you to supply a host and
domain name for the Router. Some ISPs, usually cable ISPs, require these
names as identification. You may have to check with your ISP to see if your
broadband Internet service has been configured with a host and domain name.
In most cases, leaving these fields blank will work.
Configuration Type The Router supports four connection types: Automatic
Configuration - DHCP, Static IP, PPPoE, and PPTP. Each Setup screen and
available features will differ depending on what kind of connection type you
select.
Note: You can verify that the Internet configuration settings are cor-
rect by successfully connecting to the Internet.
Figure 7-4
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Static IP
PPPoE
Some DSL-based ISPs
use PPPoE (Point-to-Point
Protocol over Ethernet) to
establish Internet connec-
tions. If you are connected
to the Internet through a
DSL line, check with your
ISP to see if they use
PPPoE. If they do, you
will have to enable
PPPoE, as shown in
Figure 7-6.
If you are required to
use a permanent IP
address to connect to
the Internet, then select
Static IP, as shown in
Figure 7-5.
User Name and Password
Enter the User Name and
Password provided by
your ISP.
Figure 7-6
Connect on Demand: Max Idle Time You can configure the Router to cut the
Internet connection after it has been inactive for a specified period of time
(Max Idle Time). If your Internet connection has been terminated due to inac-
tivity, Connect on Demand enables the Router to automatically re-establish
your connection as soon as you attempt to access the Internet again. If you wish
to activate Connect on Demand, click the radio button. In the Max Idle Time
field, enter the number of minutes you want to have elapsed before your
Internet connection terminates.
Figure 7-5
Internet IP Address This is the Router’s IP address, when seen from the WAN,
or the Internet.Your ISP will provide you with the IP Address you need to spec-
ify here.
Subnet Mask This is the Router’s Subnet Mask, as seen by external users on
the Internet (including your ISP). Your ISP will provide you with the Subnet
Mask.
KeepAlive Option: Redial Period If you select this option, the Router will peri-
odically check your Internet connection. If you are disconnected, then the
Router will automatically re-establish your connection. To use this option, click
the radio button next to KeepAlive. In the Redial Period field, you specify how
often you want the Router to check the Internet connection. The default Redial
Period is 30 seconds.
Default Gateway Your ISP will provide you with the Default Gateway Address,
which is the ISP server’s IP address.
DNS Your ISP will provide you with at least one DNS (Domain Name System)
Server IP Address.
To apply any of the settings you change on this page, click the Apply button.
To cancel any changes you’ve entered on this page, click the Cancel button. To
get more information about the features, click the Help button.
To apply any of the settings you change on this page, click the Apply button.
To cancel any changes you’ve entered on this page, click the Cancel button. To
get more information about the features, click the Help button.
Important: For ADSL users, if you enable PPPoE, remember to
remove any PPPoE applications that are already installed on any of
your PCs.
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Connect on Demand: Max Idle Time You can configure the Router to cut the
Internet connection after it has been inactive for a specified period of time
(Max Idle Time). If your Internet connection has been terminated due to inac-
tivity, Connect on Demand enables the Router to automatically re-establish
your connection as soon as you attempt to access the Internet again. If you wish
to activate Connect on Demand, click the radio button. In the Max Idle Time
field, enter the number of minutes you want to have elapsed before your
Internet connection terminates.
PPTP
Point
to
Point
Tunneling Protocol
(PPTP), selected in
the screen shown in
Figure 7-7, is a serv-
ice that applies to con-
nections in Europe
only.
KeepAlive Option: Redial Period If you select this option, the Router will peri-
odically check your Internet connection. If you are disconnected, then the
Router will automatically re-establish your connection. To use this option, click
the radio button next to Keep Alive. To use this option, click the radio button
next to Keep Alive. In the Redial Period field, you specify how often you want
the Router to check the Internet connection. The default Redial Period is 30
seconds.
To apply any of the settings you change on this page, click the Apply button.
To cancel any changes you’ve entered on this page, click the Cancel button. To
get more information about the features, click the Help button.
LAN
IP Address and LAN Subnet Mask The values for the Router’s IP Address
and Subnet Mask are shown here. The default values are 192.168.1.1 for the
LAN IP Address and 255.255.255.0 for the Subnet Mask.
Figure 7-7
Specify Internet IP Address This is the Router’s IP address, when seen from
the Internet. Your ISP will provide you with the IP Address you need to speci-
fy here.
WIRELESS
5GHz, 802.11a Wireless To enable 5GHz, 802.11a wireless networking, make
sure the Enable radio button is selected. Click the Change 5GHz Settings but-
ton to customize the 802.11a configuration (see Figure 7-8).
Subnet Mask This is the Router’s Subnet Mask, as seen by external users on
the Internet (including your ISP). Your ISP will provide you with the Subnet
Mask.
2.4GHzWireless-G To enable 2.4GHz, Wireless-G wireless networking, make
sure the Enable radio button is selected. Click the Change 2.4GHz Settings
button to customize the 802.11b configuration (see Figure 7-10).
Default Gateway Your ISP will provide you with the Default Gateway Address.
User Name and Password Enter the User Name and Password provided by
your ISP.
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
5GHz, 802.11a
5GHz, 802.11a (WEP)
The 5GHz, 802.11a portion of the Setup screen, shown in Figure 7-8, allows
The 5GHz, 802.11a (WEP) screen, shown in Figure 7-9, allows you to config-
you to configure your 5GHz, 802.11a wireless network settings.
ure your 5GHz,
802.11a WEP
settings. WEP
e n c r y p t i o n
should always
be enabled to
Figure 7-8
increase
the
security of your
Mode If you do not have any 802.11a devices in your network, you can dis-
able this broadcasting by selecting Disable.
wireless
work.
net-
Channel Select the appropriate channel from the list provided to correspond
with your network settings, between 36 and 64. All devices in your wireless
network must use the same channel in order to function correctly. If you want
the Router to automatically scan for a clear channel, then click the checkbox.
Figure 7-9
Default Transmit Key Select which WEP key (1-4) will be used when the
Router sends data. Make sure the receiver is using the same key.
SSID The SSID is the network name shared among all points in a wireless
network. The SSID must be identical for all points in the wireless network. It
is case-sensitive and must not exceed 32 characters (use any of the characters
on the keyboard). Make sure this setting is the same for all points in your wire-
less network. For added security, you should change the default SSID (linksys)
to a unique name.
WEP Encryption Keys 1-4 offer 64-bit, 128-bit, or 152-bit encryption; select
the type of encryption you want from the drop-down box. To disable WEP
Encryption, select Disable.
Passphrase (Complete this field when using 64-bit or 128-bit encryption.)
Instead of manually entering WEP keys, you can enter a Passphrase. This
Passphrase is used to generate one or more WEP keys. It is case-sensitive and
should not be longer than 16 alphanumeric characters. This Passphrase function
is compatible with Linksys wireless products only. [If you want to communi-
cate with non-Linksys wireless products, enter the WEP key(s) manually on the
non-Linksys wireless products.] After you enter the Passphrase, click the
Generate button to create WEP keys.
WEP (Encryption) An acronym for Wired Equivalent Privacy, WEP is an
encryption method used to protect your wireless data communications. WEP
uses 64-bit, 128-bit, or 152-bit keys to provide access control to your network
and encryption security for every data transmission. To decode a data trans-
mission, each device in a network must use an identical key. Higher encryption
levels offer higher levels of security, but due to the complexity of the encryp-
tion, they may decrease network performance. To enable WEP, click the radio
button beside Enable. Click the Edit WEP Settings button to configure the
WEP keys for your 5GHz, 802.11a wireless network (see Figure 7-9).
Keys 1-4 WEP keys enable you to create an encryption scheme for wireless
LAN transmissions. Manually enter a set of values. (Do not leave a key field
blank, and do not enter all zeroes. These are not valid key values.) Keys 1-4
offer 64-bit, 128-bit, or 152-bit encryption.
Check all the values, and click the Apply button to save your 5GHz, 802.11a
settings. To cancel any changes you’ve entered on this page, click the Cancel
button. To get more information about the features, click the Help button.
If you are using 64-bit WEP encryption, then the key must be exactly 10 hexa-
decimal characters in length. If you are using 128-bit WEP encryption, then the
key must be exactly 26 hexadecimal characters in length. If you are using 152-
bit WEP encryption, then the key must be exactly 32 hexadecimal characters in
length. Valid hexadecimal characters are “0”-“9” and “A”-“F”.
40
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Check all the values, and click the Apply button to save your 5GHz, 802.11a
WEP settings. To cancel any changes you’ve entered on this page, click the
Cancel button. To get more information about the features, click the Help but-
ton.
WEP (Encryption) An acronym for Wired Equivalent Privacy, WEP is an
encryption method used to protect your wireless data communications. WEP
uses a combination of 64-bit or 128-bit keys to provide access control to your
network and encryption security for every data transmission. To decode a data
transmission, each device in a network must use an identical 64-bit or 128-bit
key. Higher encryption levels offer higher levels of security, but due to the
complexity of the encryption, they may decrease network performance. To
enable WEP, click the radio button beside Enable. Click the Edit WEP
Settings button to configure the WEP keys for your 2.4GHz, Wireless-G net-
work (see Figure 7-11).
2.4GHz, 54g/Wireless-G
The 2.4GHz, 802.11g-draft portion of the Setup screen, shown in Figure 7-10
allows you to configure your 2.4GHz, Wireless-G wireless network settings.
Check all the values, and click theApply button to save your 2.4GHz, Wireless-
G settings. To cancel any changes you’ve entered on this page, click the Cancel
button. To get more information about the features, click the Help button.
2.4GHz, 54g/Wireless-G (WEP)
Figure 7-10
The 2.4GHz, 802.11b (WEP) screen, shown in Figure 7-11, allows you to con-
Mode If you have Wireless-G and 802.11b devices in your network, then keep
the default setting, Mixed. If you have only Wireless-G devices, select G-Only.
If you do not have any Wireless-G and 802.11b devices in your network, select
Disable.
figure your 2.4GHz, Wireless-G WEP settings. WEP encryption is recom-
mended
increase the
security of
to
your wireless
network.
Channel Select the appropriate channel from the list provided to correspond
with your network settings, between 36 and 64. All devices in your wireless
network must use the same channel in order to function correctly. If you want
the Router to automatically scan for a clear channel, then click the checkbox.
SSID The SSID is the network name shared among all points in a wireless
network. The SSID must be identical for all points in the wireless network. It
is case-sensitive and must not exceed 32 characters (use any of the characters
on the keyboard). Make sure this setting is the same for all points in your wire-
less network. For added security, you should change the default SSID (linksys-
g) to a unique name.
Figure 7-11
Default Transmit Key Select which WEP key (1-4) will be used when the
Router sends data. Make sure the receiver is using the same key.
SSID Broadcast When wireless clients survey the local area for wireless net-
works to associate with, they will detect the SSID broadcast by the Router. To
broadcast the Router's SSID, keep the default setting, Enable. If you do not
want to broadcast the Router's SSID, then select Disable.
WEP Encryption Keys 1-4 offer 64-bit or 128-bit encryption; select the type
of encryption you want from the drop-down box. To disable WEP Encryption,
select Disable.
42
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Passphrase Instead of manually entering WEP keys, you can enter a
Passphrase. This Passphrase is used to generate one or more WEP keys. It is
case-sensitive and should not be longer than 16 alphanumeric characters. This
Passphrase function is compatible with Linksys wireless products only. [If you
want to communicate with non-Linksys wireless products, enter the WEP
key(s) manually on the non-Linksys wireless products.] After you enter the
Passphrase, click the Generate button to create WEP keys.
Keys 1-4 WEP keys enable you to create an encryption scheme for wireless
LAN transmissions. Manually enter a set of values. (Do not leave a key field
blank, and do not enter all zeroes. These are not valid key values.) Keys 1-4
offer 64-bit or 128-bit encryption.
If you are using 64-bit WEP encryption, then the key must be exactly 10 hexa-
decimal characters in length. If you are using 128-bit WEP encryption, then the
key must be exactly 26 hexadecimal characters in length. Valid hexadecimal
characters are “0”-“9” and “A”-“F”.
Figure 7-12
L2TP - Layer Two Tunneling Protocol is an extension of the Point-to-Point
Tunneling Protocol (PPTP) used by to enable the operation of a virtual pri-
vate network (VPN) over the Internet.
Check all the values, and click theApply button to save your 2.4GHz, Wireless-
G WEP settings.
PPTP - Point-to-Point Tunneling Protocol is the method used to enable
VPN sessions to a Windows NT 4.0 or 2000 server. To allow PPTP tunnels
to pass through the Router, PPTP Pass-Through is enabled by default. To
disable PPTP Pass-Through, uncheck the box next to PPTP.
To apply any of the settings you change on this page, click the Apply button.
To cancel any changes you’ve entered on this page, click the Cancel button. To
get more information about the features, click the Help button.
Security
Web Filters Using the Web Filters feature, you may enable up to four specif-
ic filtering methods.
The Security screen, shown in Figure 7-12, allows you to change the Router’s
security settings. You should change the factory default password, which is
admin, to your own as soon as possible. All users who try to access the Router’s
web-based utility or Setup Wizard will be prompted for the Router’s password.
Proxy - Use of WAN proxy servers may compromise the Router's security.
Denying Proxy will disable access to any WAN proxy servers. To enable
proxy filtering, click the Proxy box.
Router Password The new Password must not exceed 32 characters in length
and must not include any spaces. Enter the new Password in the second field to
confirm it.
Java - Java is a programming language for websites. If you deny Java, you
run the risk of not having access to Internet sites created using this pro-
gramming language. To enable Java filtering, click the Java box.
VPN Pass-Through Virtual Private Networking (VPN) is typically used for
work-related networking. For VPN tunnels, the Router supports IPSec Pass-
Through and PPTP Pass-Through.
ActiveX - ActiveX is a programming language for websites. If you deny
ActiveX, you run the risk of not having access to Internet sites created using
this programming language. To enable ActiveX filtering, click the ActiveX
box.
IPSec - Internet Protocol Security (IPSec) is a suite of protocols used to
implement secure exchange of packets at the IP layer. To allow IPSec tun-
nels to pass through the Router, IPSec Pass-Through is enabled by default.
To disable IPSec Pass-Through, uncheck the box next to IPSec.
44
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Cookies - A cookie is data stored on your PC and used by Internet sites
when you interact with them. To enable cookie filtering, click the Cookies
box.
DMZ The DMZ hosting feature allows one local user to be exposed to the
Internet for use of a special-purpose service such as Internet gaming or video-
conferencing. DMZ hosting forwards all the ports at the same time to one PC.
The Port Forwarding feature is more secure because it only opens the ports you
want to have opened, while DMZ hosting opens all the ports of one computer,
exposing the computer so the Internet can see it.
Any PC whose port is being forwarded must have its DHCP client function dis-
abled and should have a new static IP address assigned to it because its IP
address may change when using the DHCP function.
1. To expose one PC, select Enable.
Figure 7-13
and can be downloaded for free. If the Router already works well, there’s no
need to download a newer firmware version, unless that version has a new fea-
ture that you want to use. (To learn about any new firmware with new features,
2. Enter the computer's IP address in the DMZ Host IP Address field.
3. Click the Apply button.
Block WAN Request By enabling the Block WAN Request feature, you can
prevent your network from being “pinged,” or detected, by other Internet users.
The Block WAN Request feature also reinforces your network security by hid-
ing your network ports. Both functions of the Block WAN Request feature
make it more difficult for outside users to work their way into your network.
This feature is enabled by default. Select Disable to disable this feature.
Note: By upgrading the Router’s firmware, you may lose the Router’s
configuration settings, so make sure you write down the Router’s set-
tings before you upgrade its firmware.
To upgrade the Router’s firmware:
To save your changes on this page, click the Apply button. To cancel any
unsaved changes on this page, click the Cancel button. To get more informa-
tion about the features, click the Help button.
the file using a file archive utility such as WinZip.
2. Click the Upgrade button.
System
3. On the Upgrade
Firmware screen
(see Figure 7-14),
click the Browse
button to find the
firmware upgrade
file you extract-
ed.
The System screen, shown in Figure 7-13, lets you control a variety of the
Router’s general features, from restoring factory defaults to enabling its remote
management capability.
Restore Factory Defaults Click the Yes button to reset all configuration set-
tings to their default values, and then click the Apply button. Any settings you
have saved will be lost when the default settings are restored. This feature is
disabled by default.
Figure 7-14
46
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
4. Double-click the firmware upgrade file you extracted.
Dual-Band Wireless A+G Broadband Router
Remote Management This feature allows you to manage your Router from a
remote location, via the Internet. To disable this feature, keep the default set-
ting, Disable. To enable this feature, select Enable, and use the specified port
(default is 8080) on your PC to remotely manage the Router. You must also
change the Router's default password to one of your own, if you haven’t
already. A unique password will increase security.
5. Click the Upgrade button, and follow the on-screen instructions.
Important: When you are upgrading the firmware, do NOT turn off
the Router, and do NOT press the Reset button.
Multicast Pass-Through IP Multicasting occurs when a single data transmis-
sion is sent to multiple recipients at the same time. Using the Multicast Pass-
Through feature, the Router allows IP multicast packets to be forwarded to the
appropriate computers. Keep the default setting, Enable, to support the feature,
or select Disable to disable it.
represent the Router's Internet IP address, and 8080 represents the specified
port) in your web browser’s Address field. You will be asked for the Router’s
password. After successfully entering the password, you will be able to access
the Router’s web-based utility.
MAC Cloning You can clone the MAC address of your PC’s network adapter
onto the Router.
Note: If the Remote Management feature is enabled, anyone who
knows the Router’s Internet IP address and password will be able to
alter the Router’s settings.
A MAC address is a 12-digit code assigned to a unique piece of hardware for
identification. Some ISPs require that you register the MAC address of your
PC’s network adapter, which was connected to your cable or DSL modem dur-
ing installation. To avoid calling your ISP and changing the MAC address that
is registered with the ISP, follow these instructions:
MTU MTU is the Maximum Transmission Unit. It specifies the largest pack-
et size permitted for Internet transmission. Keep the default setting, Auto, to
have the Router select the best MTU for your Internet connection. To specify a
MTU size, select Manual, and enter the value desired (default is 1400). You
should leave this value in the 1200 to 1500 range.
1. Select Enable.
2. Enter your adapter’s MAC address in the MAC Address field.
Log The Router can keep logs of all traffic for your Internet connection. To
disable the Log function, keep the default setting, Disable. To monitor traffic
between the network and the Internet, select Enable.
3. To save your new settings, click the Apply button. To cancel your changes,
click the Cancel button. To get more information about the features, click
the Help button.
To save your changes on this page, click the Apply button. To cancel any
unsaved changes on this page, click the Cancel button. To get more information
about the features, click the Help button.
To disable MAC address cloning, keep the default setting, Disable.
If you do not know your adapter’s MAC address, follow these instructions:
1. Click the Start button, and select Run.
2. Enter command in the field provided, and press the OK button.
3. At the command prompt, enter ipconfig /all. Then press the Enter key.
4. Write down your adapter’s physical address; this is the adapter’s MAC
address.
48
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Client Lease Time The Client Lease Time is the amount of time a network
user will be allowed connection to the Router with their current dynamic IP
address. Enter the amount of time, in minutes, that the user will be “leased” this
dynamic IP address. After the time is up, the user will be automatically
assigned a new dynamic IP address. The default is 0 minutes, which means one
day.
DHCP
The DHCP screen, shown in Figure 7-15, allows you to configure the settings
for the Router’s Dynamic Host Configuration Protocol (DHCP) server function.
The Router can be used as a DHCP server for your network. A DHCP server
automatically assigns an IP address to each computer on your network.
Static DNS 1-3 The Domain Name System (DNS) is how the Internet trans-
lates domain or website names into Internet addresses or URLs. Your ISP will
provide you with at least one DNS Server IP Address. If you wish to use anoth-
er, type that IP Address in one of these fields. You can type up to three DNS
Server IP Addresses here. The Router will use these for quicker access to func-
tioning DNS servers.
WINS The Windows Internet Naming Service (WINS) manages each PC’s
interaction with the Internet. If you use a WINS server, enter that server’s IP
Address here. Otherwise, leave this blank.
Currently Assigned: DHCP Clients Table Click the DHCP Clients Table
button to view the list of PCs that are given IP addresses by the Router (see
Figure 7-16). For each PC, the list shows the Client Hostname, IP Address,
MAC Address, and and the amount of DHCP client lease time left. Click the
Refresh button to display the most current information.
Figure 7-15
If you choose to enable the Router’s DHCP server option, you must configure all
of your network PCs to connect to a DHCP server (the Router), and make sure
there is no other DHCP server on your network.
DHCP Server DHCP is enabled by factory default. If you already have a
DHCP server on your network, or you don’t want a DHCP server, then click the
Disable radio button (no other DHCP features will be available).
Figure 7-16
Starting IP Address Enter a value for the DHCP server to start with when
issuing IP addresses. Because the Router’s default IP address is 192.168.1.1,
the Starting IP Address must be 192.168.1.2 or greater, but smaller than
192.168.1.253. The default Starting IP Address is 192.168.1.100.
To save your changes on this page, click the Apply button. To cancel any
unsaved changes on this page, click the Cancel button. To get more information
about the features, click the Help button.
Maximum Number of DHCP Users (Optional) Enter the maximum number
of PCs that you want the DHCP server to assign IP addresses to. This number
cannot be greater than 253. The default is 50.
50
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
SNMP
Status
The SNMP tab, shown in Figure 7-17, allows you to customize the Simple
Network Management Protocol (SNMP) settings. SNMP is a popular network
monitoring and management protocol.
The Status screen, shown in Figure 7-18, displays the Router’s current status
and configuration. All information is read-only.
Figure 7-17
The Identification settings let you designate the Contact, Device Name, and
Location information for the Router. The SNMP Community settings allow
names to be assigned to any SNMP communities that have been set up in the
network. You can define two different SNMP communities, with the default
names being Public and Private.
SNMPv2. To enable the SNMP support feature, select Enable.
Identification. In the Contact field, enter contact information for the Router.
In the Device Name field, enter the name of the Router. In the Location field,
specify the area or location where the Router resides.
SNMP Community. You may change the name from its default, Public. Enter
a new name in the Public field. Then configure the community's access as
either Read-Only or Read-Write.You may change the name from its default,
Private. Enter a new name in the Private field. Then configure the communi-
ty's access as either Read-Only or Read-Write.
Figure 7-18
Note: The information provided and buttons available may vary
depending on the Router’s settings.
When you’ve completed making any changes on this tab, click the Apply but-
ton to save those changes or Cancel to cancel your changes. For more infor-
mation on this tab, you can click the Help button.
52
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Firmware Version The version number of the firmware currently installed is
displayed here.
Internet
Configuration Type The type of Internet connection is displayed here.
Current Time The current time, as set from the Setup tab, is displayed here.
Status For PPPoE or PPTP, the status of the Internet connection is displayed
here. If there is no connection, you can click the Connect button to re-estab-
lish it. If there is a connection, you can click the Disconnect button to end it.
Host Name The Host Name is the name of the Router. This entry is necessary
for some ISPs.
Domain Name The Domain Name is the name of the Router's domain. This
entry is necessary for some ISPs.
IP Address, Subnet Mask, and Default Gateway The Router’s IP Address,
Subnet Mask, and Default Gateway Address, as seen by external users on the
Internet, are displayed here.
LAN
DNS The DNS (Domain Name System) IP Addresses currently used by the
Router are shown here. Multiple DNS IP settings are common. In most cases,
the first available DNS entry is used.
IP Address and Subnet Mask The current IP Address and Subnet Mask of
the Router, as seen by users on your local area network (LAN), are displayed
here.
To refresh the Status screen, click the Refresh button. To get more information
DHCP Server The status of the Router's DHCP server function is displayed
about the features, click the Help button.
here.
Help
Wireless 5GHz, 802.11a
The Help screen, shown in Figure 7-19, offers links to all of the Router’s tech-
nical support resources and the application that upgrades the Router’s
firmware. For additional information about each screen of the web-based util-
ity, click the appropriate link on the lefthand side of the Help screen.
Mode The Mode setting, as set from the Setup tab, is displayed here.
SSID The SSID of the 5GHz, 802.11a network is displayed here.
Channel The channel for the 5GHz, 802.11a wireless network is displayed
here.
Encryption Function The status of the WEP encryption is displayed here.
Wireless 2.4GHz, Wireless-G
Mode The Mode setting, as set from the Setup tab, is displayed here.
SSID The SSID of the 2.4GHz, 802.11b network is displayed here.
Channel The channel for the 2.4GHz, 802.11b wireless network is displayed
here.
Figure 7-19
Encryption Function The status of the WEP encryption is displayed here.
54
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Linksys Website Clicking this link will take you to Linksys’s website,
www.linksys.com, provided you are connected to the Internet.
Wireless MAC Filters
Wireless access can be filtered by using the MAC addresses of the wireless
devices transmitting within your network’s radius. Select Enable from the drop-
down menu and choose if you wish to Prevent wireless access by MAC address
or Permit by MAC Address. Then, click the Edit MAC Filter List button to
access a secondary screen, where you can enter the MAC Addresses of the
devices you wish to filter.
Online User Guide in PDF Format and Adobe Website Clicking the Online
User Guide in PDF format link opens the Router’s User Guide. The User
Guide is in Adobe Acrobat Portable Document File (.pdf) format, so you need
the Adobe Acrobat Reader to view it. If you do not have the Acrobat Reader,
click the Adobe website link to download it.
Advanced Tabs
The following instructions are for advanced users or users whose setup needs
require special configuration. When you click the Advanced tab, you will be
able to set up these features. There are six additional tabs available.
Advanced Wireless - Allows you to customize data transmission and 802.1x
settings for your wireless network(s).
Internet Filter - Enables you to set up filters that block specific internal users
from Internet access.
Port Forwarding - Lets you set up public services on your network, such as an
ftp server, mail server, or web server.
Routing - Enables you to configure the routing mode of the Router.
DDNS - Allows you to enable the Dynamic Domain Name System (DDNS)
feature, so a fixed domain name can be assigned to a dynamic Internet IP
address.
If you need to access the basic configuration tabs, click the Setup tab.
Advanced Wireless
Figure 7-20
The Advanced Wireless screen, shown in Figure 7-20, allows you to customize
data transmission settings. In most cases, the advanced wireless settings on this
screen should remain at their default values.
5GHz, 802.11a
Authentication Type The default is set to Auto, which allows either Open
System or Shared Key authentication to be used. For Open System authentica-
tion, the sender and the recipient do NOT use a WEP key for authentication.
For Shared Key authentication, the sender and recipient use a WEP key for
authentication. If you want to use only Shared Key authentication, then select
Shared Key.
56
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Transmission Rate The rate of data transmission should be set depending on
the speed of your wireless network.You can select from a range of transmission
speeds (6, 9, 12, 18, 24, 36, 48, or 54Mbps), or you can select Auto to have the
Router automatically use the fastest possible data rate and enable the Auto-
Fallback feature. Auto-Fallback will negotiate the best possible connection
speed between the Router and a wireless client. The default value is Auto.
Fragmentation Threshold This value specifies the maximum size for a pack-
et before data is fragmented into multiple packets. If you experience a high
packet error rate, you may slightly increase the Fragmentation Threshold.
Setting the Fragmentation Threshold too low may result in poor network per-
formance. Only minor reduction of the default value is recommended. In most
cases, it should remain at its default value of 2346.
Transmit Power Control The greater the transmit power used, the larger the
area a wireless network covers. To minimize the likelihood of eavesdropping by
unauthorized wireless users, do not use more transmit power than necessary to
cover the range needed for your wireless network. Try using the Router at dif-
ferent levels of transmit power, and determine how much transmit power is
needed to reach the wireless client, such as a PC, or access point that is farthest
from the Router. Then select the appropriate level of transmit power (Full,
Half, Quarter, Eighth, or Min) from the drop-down menu. The default value
is Full.
2.4GHz, 54g/Wireless-G
Authentication Type The default is set to Auto, which allows either Open
System or Shared Key authentication to be used. For Open System authentica-
tion, the sender and the recipient do NOT use a WEP key for authentication.
For Shared Key authentication, the sender and recipient use a WEP key for
authentication. If you want to use only Shared Key authentication, then select
Shared Key.
Transmission Rate The rate of data transmission should be set depending on
the speed of your wireless network.You can select from a range of transmission
speeds (6, 9, 12, 18, 24, 36, 48, or 54Mbps), or you can select Auto to have the
Router automatically use the fastest possible data rate and enable the Auto-
Fallback feature. Auto-Fallback will negotiate the best possible connection
speed between the Router and a wireless client. The default value is Auto.
Beacon Interval The default value is 100. Enter a value between 1 and 65,535
milliseconds. The Beacon Interval value indicates the frequency interval of the
beacon. A beacon is a packet broadcast by the Router to synchronize the wire-
less network.
DTIM Interval This value, between 1 and 16384, indicates the interval of the
Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown
field informing clients of the next window for listening to broadcast and mul-
ticast messages. When the Router has buffered broadcast or multicast messages
for associated clients, it sends the next DTIM with a DTIM Interval value. Its
clients hear the beacons and awaken to receive the broadcast and multicast mes-
sages. The default value is 1.
Beacon Interval The Beacon Interval value indicates the frequency interval of
the beacon. Enter a value between 20 and 1000. A beacon is a packet broadcast
by the Router to synchronize the wireless network. The default value is 100.
DTIM Interval This value, between 1 and 16384, indicates the interval of the
Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown
field informing clients of the next window for listening to broadcast and mul-
ticast messages. When the Router has buffered broadcast or multicast messages
for associated clients, it sends the next DTIM with a DTIM Interval value. Its
clients hear the beacons and awaken to receive the broadcast and multicast mes-
sages. The default value is 1.
RTS Threshold Should you encounter inconsistent data flow, only minor
reduction of the default value, 2346, is recommended. If a network packet is
smaller than the preset RTS threshold size, the RTS/CTS mechanism will not
be enabled. The Router sends Request to Send (RTS) frames to a particular
receiving station and negotiates the sending of a data frame. After receiving an
RTS, the wireless station responds with a Clear to Send (CTS) frame to
acknowledge the right to begin transmission. The RTS Threshold value should
remain at its default value of 2346.
RTS Threshold Should you encounter inconsistent data flow, only minor
reduction of the default value, 2346, is recommended. If a network packet is
smaller than the preset RTS threshold size, the RTS/CTS mechanism will not
be enabled. The Router sends Request to Send (RTS) frames to a particular
receiving station and negotiates the sending of a data frame. After receiving an
RTS, the wireless station responds with a Clear to Send (CTS) frame to
acknowledge the right to begin transmission. The RTS Threshold value should
remain at its default value of 2346.
58
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Fragmentation Threshold This value specifies the maximum size for a pack-
et before data is fragmented into multiple packets. If you experience a high
packet error rate, you may slightly increase the Fragmentation Threshold.
Setting the Fragmentation Threshold too low may result in poor network per-
formance. Only minor reduction of this value is recommended. In most cases,
it should remain at its default value of 2346.
Internet Access Policy Multiple Filters can be saved as Internet Access
Policies. When you wish to edit one, select the number of the Policy from the
drop-down menu. The tab will change to reflect the settings of this Policy. If
you wish to delete this Policy, click the Delete button.
To see a summary of all Policies, click the Summary button.
To apply any of the settings you change on this page, click the Apply button.
To cancel any changes you’ve entered on this page, click the Cancel button. To
get more information about the features, click the Help button.
The summaries are list-
ed on this screen,
shown in Figure 7-22,
with their name and
settings. To delete any
summary from this
screen, check the
empty box beneath
Delete and then click
the Delete button. To
Internet Filter
The Internet Filter tab, shown in Figure 7-21, allows you to block or allow spe-
cific kinds of Internet usage. You can set up Internet access policies for specif-
ic PCs and set up filters by using network port numbers.
return to the Filters tab,
click the Close button.
Figure 7-22
Enter Policy Name Policies are created from the fields presented here. To
create a policy:
1. Enter a Policy Name in the field provided.
2. Click the Edit List
of PCs button. This
will open the List of
PCs screen, shown
in Figure 7-23.
From this screen,
you can enter the IP
address or MAC
address of any PC
to which this policy
will apply. You can
even enter ranges of
PCs by IP address.
Figure 7-23
Click the Apply
button to save your settings, the Cancel button to undo any changes, and the
Close button to return to the Filters tab.
Figure 7-21
60
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
3. Select if you wish to Disable or Enable Internet access for those PCs you
listed on the List of PCs screen by clicking the radio button beside either
option.
Port Forwarding
The Port Forwarding screen, shown in Figure 7-25, sets up public services on
your network, such as web servers, ftp servers, e-mail servers, or other spe-
cialized Internet applications. (Specialized Internet applications are any appli-
cations that use Internet access to perform functions such as videoconferencing
or online gaming. Some Internet applications may not require any forwarding.)
4. You can filter
access to various
services accessed
over the Internet,
such as FTP or
Telnet, by selecting
a service from the
pull-down menus
next to Services. If
a service isn’t listed,
you can click the
Add Service button
Figure 7-24
to open the Service
screen, shown in Figure 7-24, and add a service to the list. You will need to
enter a Service name, as well as the Protocol and Port Range used by the
service.
5. By selecting the appropriate setting next to Days and Time, choose when
Internet access will be filtered.
6. Lastly, click the Apply button to save and activate this policy.
Internet Access can also be filtered by URL Address, the address entered to
access Internet sites, by entering the address in one of the Website Blocking
by URL Address fields. If you do not know the URL Address, filtering can be
done by Keyword by entering a keyword in one of the Website Blocking by
Keyword fields.
Figure 7-25
Note: Any PC whose port is being forwarded should have its DHCP
client function disabled and a new static IP address assigned to it
because its IP address may change when using the DHCP function.
To apply any of the settings you change on this page, click the Apply button. To
cancel any changes you’ve entered on this page, click the Cancel button. To get
more information about the features, click the Help button.
Customized Applications In the field provided, enter the name you wish to
give each application.
External Port For each application, enter the number of the External Ports
(the port numbers seen by users on the Internet) in the appropriate fields. (To
find out the port range, check your application’s documentation.) If there is
only one External Port, enter its number in both External Port fields.
62
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Protocol TCP Click this checkbox if you want to forward the data transmis-
sions that use the TCP protocol.
Port Triggering Port Triggering is used for special Internet applications whose
outgoing ports differ from the incoming ports. For this feature, the Router will
watch outgoing data for specific port numbers. The Router will remember the
IP address of the computer that sends a transmission requesting data, so that
when the requested data returns through the Router, the data is pulled back to
the proper computer by way of IP address and port mapping rules. Click the
Port Triggering button to set up triggered ports, and follow these instructions:
Protocol UDP Click this checkbox if you want to forward the data transmis-
sions that use the UDP protocol.
IP Address For each application, enter the IP Address of the PC running the
specific application.
1. Enter
the
Enable Click the Enable checkbox to enable port forwarding for the relevant
application.
Application
Name of the
trigger (see
Figure 7-26).
The following table shows the typical port forwarding settings for common
Internet applications.
Applications
FTP
External Port TCP Protocol UDP Protocol
21
√
Telnet
SMTP
DNS
23
√
√
25
53
√
TFTP
69
√
Figure 7-26
Finger
HTTP
POP3
79
√
√
√
√
2. Enter the Outgoing Port Range used by the application. Check with the
Internet application for the port number(s) needed.
80
110
3. Enter the Incoming Port Range used by the application. Check with the
Internet application for the port number(s) needed.
NNTP
SNMP
119
161
√
4. Click the Apply button to save your changes. Click the Cancel button to
cancel your unsaved changes. Click the Close button to return to the Port
Forwarding screen.
To apply any of the settings you change on this page, click the Apply button. To
cancel any changes you’ve entered on this page, click the Cancel button. To get
more information about the features, click the Help button.
To save your changes on this page, click the Apply button. To cancel any
unsaved changes on this page, click the Cancel button. To get more informa-
tion about the features, click the Help button.
64
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
4. To set up a static route between the Router and another network, select a
number from the Static Routing drop-down list. (A static route is a pre-
determined pathway that network information must travel to reach a spe-
cific host or network.)
Routing
On the Routing screen, shown in Figure 7-27, you can set the routing mode of
the Router. Gateway mode is recommended for most users.
5. Enter the following data:
•
•
•
Enter Route Name - Enter a name for the Route here, using a maxi-
mum of 25 alphanumeric characters.
Destination LAN IP - The Destination LAN IP is the address of the
remote network or host to which you want to assign a static route.
Subnet Mask - The Subnet Mask determines which portion of a
Destination LAN IP address is the network portion, and which portion
is the host portion.
•
•
Gateway - This is the IP address of the gateway device that allows for
contact between the Router and the remote network or host.
Interface - This interface tells you whether the Destination IP Address
is on the LAN & Wireless (internal wired and wireless networks), the
WAN (Internet), or Loopback (a dummy network in which one PC
acts like a network-necessary for certain software programs).
Figure 7-27
Note: The Routing screen and available features will vary depending
on which mode you select.
6. To cancel your changes, click the Cancel button. To save your changes,
click the Apply button. To get more information about the features, click
the Help button.
To set up routing:
1. Choose the correct working mode. Select Gateway if the Router is hosting
your network’s connection to the Internet (recommended for most users).
Select Router if the Router exists on a network with other routers.
Note: If you have more than one router on your network, you should
select Router for the working mode.
To delete a static route entry:
1. From the Static Routing drop-down list, select the entry number of the stat-
ic route.
2. If you selected the Gateway mode, click the Apply button. If you selected
2. Click the Delete This Entry button.
the Router mode, proceed to step 3.
3. To cancel a deletion, click the Cancel button. To save a deletion, click the
Apply button. To get more information about the features, click the Help
button.
3. For Dynamic Routing, the default is Disable. The Dynamic Routing feature
enables the Router to automatically adjust to physical changes in the net-
work’s layout and exchange routing tables with the other router(s). The
Router determines the network packets’ route based on the fewest number
of hops between the source and the destination. Select Enable to enable the
Dynamic Routing feature for data transmissions.
66
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Show Routing Table Click the Show Routing Table button to view all of the
valid dynamic and static route entries in use (see Figure 7-28). The Destination
LAN IP address, Subnet Mask, Gateway, and Interface information are dis-
played for each entry. Click the Refresh button to display the most up-to-date
data.
DDNS Service To enable DDNS Service, select Enable and follow these
instructions:
1. Sign up for a DDNS service and write down your User Name, Password,
and Host Name information.
2. On the DDNS screen, select Enable.
3. Complete the User Name, Password, and Host Name fields.
4. To save your new settings, click the Apply button. To cancel your changes,
click the Cancel button.
Figure 7-28
Internet IP Address The Router’s current Internet IP Address is displayed
here.
DDNS
The Router offers a Dynamic Domain Name System (DDNS) feature. DDNS
lets you assign a fixed host and domain name to a dynamic Internet IP address.
It is useful when you are hosting your own website, FTP server, or other serv-
er behind the Router. Before you can use this feature, you need to sign up for
Status The status of the DDNS service connection is displayed here.
To save your changes on this page, click the Apply button. To cancel any
unsaved changes on this page, click the Cancel button. To get more information
about the features, click the Help button.
Figure 6-27
68
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
For Windows 2000:
Appendix A: Troubleshooting
Common Problems and Solutions
A. Click Start, Settings, and Control Panel. Double-click Network and
Dial-Up Connections.
B. Right-click the Local Area Connection that is associated with the Ethernet
adapter you are using, and select the Properties option.
C. In the Components checked are used by this connection box, highlight
Internet Protocol (TCP/IP), and click the Properties button. Select Use
the following IP address option.
D. Enter a unique IP address that is not used by any other computer on the
network connected to the Router. You can only use an IP address in the
ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to 192.168.1.254.
E. Enter the Subnet Mask, 255.255.255.0.
F. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
G. Toward the bottom of the window, select Use the following DNS server
addresses, and enter the Preferred DNS server and Alternative DNS
server (provided by your ISP). Contact your ISP or go on its website to find
the information.
This appendix consists of two parts: “Common Problems and Solutions” and
“Frequently Asked Questions.” Provided are possible solutions to problems that
may occur during the installation and operation of the Router. Read the descrip-
tions below to help solve your problems. If you can’t find an answer here, check
1. I need to set a static IP address on a PC.
The Router, by default, assigns an IP address range of 192.168.1.100 to
192.168.1.150 using the DHCP server on the Router. To set a static IP address,
you can only use the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151 to
192.168.1.254. Each PC or network device that uses TCP/IP must have a
unique address to identify itself in a network. If the IP address is not unique to
a network, Windows will generate an IP conflict error message. You can assign
a static IP address to a PC by performing the following steps:
H. Click the OK button in the Internet Protocol (TCP/IP) Properties window,
and click the OK button in the Local Area Connection Properties window.
I. Restart the computer if asked.
For Windows 98 and Me:
A. Click Start, Settings, and Control Panel. Double-click Network.
B. In The following network components are installed box, select the TCP/IP->
associated with your Ethernet adapter. If you only have one Ethernet adapter
installed, you will only see one TCP/IP line with no association to an Ethernet
adapter. Highlight it and click the Properties button.
C. In the TCP/IP properties window, select the IP address tab, and select
Specify an IP address. Enter a unique IP address that is not used by any
other computer on the network connected to the Router. You can only use
an IP address in the ranges 192.168.1.2 to 192.168.1.99 and 192.168.1.151
to 192.168.1.254. Make sure that each IP address is unique for each PC or
network device.
D. Click the Gateway tab, and in the New Gateway prompt, enter 192.168.1.1,
which is the default IP address of the Router. Click the Add button to accept
the entry.
E. Click the DNS tab, and make sure the DNS Enabled option is selected.
Enter the Host and Domain names (e.g., John for Host and home for
Domain). Enter the DNS entry provided by your ISP. If your ISP has not
provided the DNS IP address, contact your ISP to get that information or go
to its website for the information.
For Windows NT 4.0:
A. Click Start, Settings, and Control Panel. Double-click the Network icon.
B. Click the Protocol tab, and double-click TCP/IP Protocol.
C. When the window appears, make sure you have selected the correct
Adapter for your Ethernet adapter.
D. Select Specify an IP address, and enter a unique IP address that is not
used by any other computer on the network connected to the Router. You
can only use an IP address in the ranges 192.168.1.2 to 192.168.1.99 and
192.168.1.151 to 192.168.1.254.
E. Enter the Subnet Mask, 255.255.255.0.
F. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
G. Click the DNS tab, and enter the Host and Domain names (e.g., John for
Host and home for Domain). Under DNS Service Search Order, click the
Add button. Enter the DNS IP address in the DNS Server field, and click
the Add button. Repeat this action for all DNS IP addresses given by your
ISP.
H. Click the OK button in the TCP/IP Protocol Properties window, and click
the Close button in the Network window.
I. Restart the computer if asked.
F. Click the OK button in the TCP/IP properties window, and click Close or
the OK button for the Network window.
G. Restart the computer when asked.
70
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
For Windows XP:
B. Open a command prompt.
• For Windows 98 and Me, please click Start and Run. In the Open field,
type in command. Press the Enter key or click the OK button.
• For Windows NT, 2000, and XP, please click Start and Run. In the
Open field, type cmd. Press the Enter key or click the OK button.
The following instructions assume you are running Windows XP with the
default interface. If you are using the Classic interface (where the icons and
menus look like previous Windows versions), please follow the instructions for
Windows 2000.
C. In the command prompt, type ping 192.168.1.1 and press the Enter key.
• If you get a reply, the computer is communicating with the Router.
• If you do NOT get a reply, please check the cable, and make sure Obtain
an IP address automatically is selected in the TCP/IP settings for your
Ethernet adapter.
A. Click Start and Control Panel.
B. Click the Network and Internet Connections icon and then the Network
Connections icon.
C. Right-click the Local Area Connection that is associated with the Ethernet
adapter you are using, and select the Properties option.
D. In the This connection uses the following items box, highlight Internet
Protocol (TCP/IP). Click the Properties button.
E. Enter a unique IP address that is not used by any other computer on the net-
work connected to the Router. You can only use an IP address in the ranges
192.168.1.2 to 192.168.1.99 and 192.168.1.151 to 192.168.1.254.
F. Enter the Subnet Mask, 255.255.255.0.
D. In the command prompt, type ping followed by your Internet or WAN IP
address and press the Enter key. The Internet or WAN IP Address can be
found on the Status screen of the Router’s web-based utility. For example,
if your Internet or WAN IP address is 1.2.3.4, you would enter ping 1.2.3.4
and press the Enter key.
• If you get a reply, the computer is connected to the Router.
G. Enter the Default Gateway, 192.168.1.1 (Router’s default IP address).
H. Toward the bottom of the window, select Use the following DNS server
addresses, and enter the Preferred DNS server and Alternative DNS
server (provided by your ISP). Contact your ISP or go on its website to find
the information.
• If you do NOT get a reply, try the ping command from a different com-
puter to verify that your original computer is not the cause of the problem.
key.
I. Click the OK button in the Internet Protocol (TCP/IP) Properties window.
Click the OK button in the Local Area Connection Properties window.
• If you get a reply, the computer is connected to the Internet. If you can-
not open a webpage, try the ping command from a different computer to
verify that your original computer is not the cause of the problem.
• If you do NOT get a reply, there may be a problem with the connection.
Try the ping command from a different computer to verify that your orig-
inal computer is not the cause of the problem.
2. I want to test my Internet connection.
A. Check your TCP/IP settings.
For Windows 98, Me, 2000, and XP:
Refer to “Chapter 4: Configure the PCs” for details. Make sure Obtain IP
address automatically is selected in the settings.
3. I am not getting an IP address on the Internet with my Internet connection.
A. Refer to “Problem #2, I want to test my Internet connection” to verify that
you have connectivity.
For Windows NT 4.0:
• Click Start, Settings, and Control Panel. Double-click the Network
icon.
• Click the Protocol tab, and double-click on TCP/IP Protocol.
• When the window appears, make sure you have selected the correct
Adapter for your Ethernet adapter and set it for Obtain an IP address
from a DHCP server.
• Click the OK button in the TCP/IP Protocol Properties window, and
click the Close button in the Network window.
• Restart the computer if asked.
B. If you need to register the MAC address of your Ethernet adapter with your
ISP, please see “Appendix D: Finding the MAC address and IP Address for
Your Ethernet Adapter.” If you need to clone the MAC address of your
Ethernet adapter onto the Router, see the MAC Address Clone section of
“Chapter 7: The Router’s Web-based Utility” for details.
C. Make sure you are using the right Internet connection settings. Contact your
ISP to see if your Internet connection type is DHCP, Static IP Address, or
PPPoE (commonly used by DSL consumers). Please refer to the Setup sec-
tion of “Chapter 7: The Router’s Web-based Utility” for details on Internet
connection settings.
72
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
D. Make sure you have the right cable. Check to see if the Internet column has
a solidly lit Link/Act LED.
of the web interface. If you assigned a static IP address to any computer or net-
work device on the network, you need to change its IP address accordingly to
192.168.2.Y (Y being any number from 1 to 254). Note that each IP address
must be unique within the network.
E. Make sure the cable connecting from your cable or DSL modem is con-
nected to the Router’s Internet port. Verify that the Status page of the
Router’s web-based utility shows a valid IP address from your ISP.
F. Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds,
and then turn on the Router, cable/DSL modem, and computer. Check the
Status tab of the Router’s web-based utility to see if you get an IP address.
Your VPN may require port 500/UDP packets to be passed to the computer that
is connecting to the IPSec server. Refer to “Problem #7, I need to set up online
game hosting or use other Internet applications” for details.
4. I am not able to access the Setup page of the Router’s web-based utility.
A. Refer to “Problem #2, I want to test my Internet connection” to verify that
your computer is properly connected to the Router.
6. I need to set up a server behind my Router.
B. Refer to “Appendix D: Finding the MAC Address and IP address for Your
Ethernet Adapter” to verify that your computer has an IP Address, Subnet
Mask, Gateway, and DNS.
C. Set a static IP address on your system; refer to “Problem #1: I need to set a
static IP address.”
To use a server like a web, ftp, or mail server, you need to know the respective
port numbers they are using. You can get more information by viewing the doc-
umentation provided with the server you installed. Follow these steps to set up
port forwarding through the Router’s web-based utility. We will be setting up
web, ftp, and mail servers.
D. Refer to “Problem #10: I need to remove the proxy settings or the dial-up
pop-up window (for PPPoE users).”
IP address of the Router. Go to the Advanced => Port Forwarding tab.
B. Enter any name you want to use for the Customized Application.
C. Enter the External Port range of the service you are using. For example,
if you have a web server, you would enter the range 80 to 80.
D. Check the protocol you will be using, TCP and/or UDP.
5. I can’t get my Virtual Private Network (VPN) working through the Router.
address of the Router, go to the System tab. Make sure you have IPsec pass-
through, L2TP, and PPTP pass-through enabled.
E. Enter the IP address of the PC or network device that you want the port
server to go to. For example, if the web server’s Ethernet adapter IP address
is 192.168.1.100, you would enter 100 in the field provided. Check
“Appendix D: Finding the MAC Address and IP Address for Your Ethernet
Adapter” for details on getting an IP address.
VPNs that use IPSec with the ESP (Encapsulation Security Payload known as
protocol 50) authentication will work fine. At least one IPSec session will work
through the Router; however, simultaneous IPSec sessions may be possible,
depending on the specifics of your VPNs.
F. Check the Enable option for the port services you want to use. Consider the
example below:
VPNs that use IPSec and AH (Authentication Header known as protocol 51)
are incompatible with the Router. AH has limitations due to occasional incom-
patibility with the NAT standard.
Customized
Application
Web server
FTP server
SMTP (outgoing) 25 to 25
POP3 (incoming) 110 to 110
External Port
TCP
UDP
X
IP Address
Enable
Change the IP address for the Router to another subnet to avoid a conflict
between the VPN IP address and your local IP address. For example, if your
VPN server assigns an IP address 192.168.1.X (X is a number from 1 to 254)
and your local LAN IP address is 192.168.1.X (X is the same number used in
the VPN IP address), the Router will have difficulties routing information to
the right location. If you change the Router’s IP address to 192.168.2.1, that
should solve the problem. Change the Router’s IP address through the Setup tab
80 to 80
21 to 21
X
X
X
X
192.168.1.100
192.168.1.101
192.168.1.102
192.168.1.102
X
X
X
X
X
X
When you have completed the configuration, click the Apply button.
74
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
7. I need to set up online game hosting or use other Internet applications.
Dual-Band Wireless A+G Broadband Router
settings. If the port number that the data enters from does not have port for-
warding, then the Router will send the data to whichever PC or network device
you set for DMZ hosting.) Follow these steps to set DMZ hosting:
If you want to play online games or use Internet applications, most will work
without doing any port forwarding or DMZ hosting. There may be cases when
you want to host an online game or Internet application. This would require you
to set up the Router to deliver incoming packets or data to a specific comput-
er. This also applies to the Internet applications you are using. The best way to
get the information on what port services to use is to go to the website of the
online game or application you want to use. Follow these steps to set up online
game hosting or use a certain Internet application:
IP address of the Router. Go to the Advanced => Port Forwarding tab.
B. Disable or remove the entries you have entered for forwarding. Keep this
information in case you want to use it at a later time.
C. Click the Security tab and select DMZ Host.
D. Enter the Ethernet adapter’s IP address of the computer you want exposed
to the Internet. This will bypass the NAT firewall for that computer. Please
refer to “Appendix D: Finding the MAC Address and IP Address for Your
Ethernet Adapter” for details on getting an IP address.
address of the Router. Go to the Advanced => Port Forwarding tab.
B. Enter any name you want to use for the Customized Application.
C. Enter the External Port range of the service you are using. For example,
if you want to host Unreal Tournament (UT), you would enter the range
7777 to 27900.
Once completed with the configuration, click the Apply button.
D. Check the protocol you will be using, TCP and/or UDP.
E. Enter the IP address of the PC or network device that you want the port
server to go to. For example, if the web server’s Ethernet adapter IP address
is 192.168.1.100, you would enter 100 in the field provided. Check
“Appendix D: Finding the MAC Address and IP Address for Your Ethernet
Adapter” for details on getting an IP address.
9. I forgot my password, or the password prompt always appears when I am sav-
ing settings to the Router.
Reset the Router to factory default by pressing the Reset button for 10 seconds
and then releasing it. If you are still getting prompted for a password when sav-
ing settings, then perform the following steps:
F. Check the Enable option for the port services you want to use. Consider the
example below:
IP address of the Router. Enter the default password admin, and click the
Security tab.
Customized
Application
UT
Halflife
PC Anywhere
VPN IPSEC
External Port
TCP
X
UDP
IP Address
Enable
B. Enter a different password in the Router Password field, and enter the
same password in the second field to confirm the password.
C. Click the Apply button.
7777 to 27900
X
X
X
X
192.168.1.100
192.168.1.105
192.168.1.102
192.168.1.100
X
X
X
X
27015 to 27015 X
5631 to 5631
500 to 500
10. I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-
up window.
If you have proxy settings, you need to disable these on your computer.
Because the Router is the gateway for the Internet connection, the computer
does not need any proxy settings to gain access. Please follow these directions
to verify that you do not have any proxy settings and that the browser you use
is set to connect directly to the LAN.
When you have completed the configuration, click the Apply button.
8. I can’t get the Internet game, server, or application to work.
If you are having difficulties getting any Internet game, server, or application
to function properly, consider exposing one PC to the Internet using
DeMilitarized Zone (DMZ) hosting. This option is available when an applica-
tion requires too many ports or when you are not sure which port services to
use. Make sure you disable all the forwarding entries if you want to success-
fully use DMZ hosting, since forwarding has priority over DMZ hosting. (In
other words, data that enters the Router will be checked first by the forwarding
For Microsoft Internet Explorer 5.0 or higher:
A. Click Start, Settings, and Control Panel. Double-click Internet Options.
B. Click the Connections tab.
C. Click the LAN settings button and remove anything that is checked.
D. Click the OK button to go back to the previous screen.
76
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
E. Click the option Never dial a connection. This will remove any dial-up
C. Perform the upgrade using the Upgrade Utility, TFTP program or Router’s
web-based utility through its Help tab.
pop-ups for PPPoE users.
For Netscape 4.7 or higher:
14. My DSL service’s PPPoE is always disconnecting.
A. Start Netscape Navigator, and click Edit, Preferences, Advanced, and
PPPoE is not actually a dedicated or always-on connection. The DSL ISP can
disconnect the service after a period of inactivity, just like a normal phone dial-
up connection to the Internet. There is a setup option to “keep alive” the con-
nection. This may not always work, so you may need to re-establish connec-
tion periodically.
Proxies.
B. Make sure you have Direct connection to the Internet selected on this
screen.
C. Close all the windows to finish.
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. On the Setup screen, select the option Keep Alive, and set the Redial
Period option at 30 (seconds).
11. To start over, I need to set the Router to factory default.
Hold the Reset button for 10 seconds and then release it. This will return the
password, forwarding, and other settings on the Router to the factory default
settings. In other words, the Router will revert to its original factory configu-
ration.
D. Click the Apply button.
E. Click the Status tab, and click the Connect button.
F. You may see the login status display as Connecting. Press the F5 key to
refresh the screen, until you see the login status display as Connected.
G. Click the Apply button to continue.
12. I need to upgrade the firmware.
In order to upgrade the firmware with the latest features, you need to go to the
these steps:
If the connection is lost again, follow steps E to G to re-establish connection.
latest firmware.
15. I can’t access my e-mail, web, or VPN, or I am getting corrupted data from the
Internet.
B. To upgrade the firmware, follow the steps in the Help section found in
“Chapter 7: The Router’s Web-based Utility.”
The Maximum Transmission Unit (MTU) setting may need to be adjusted. By
default, the MTU is set at 1400. For most DSL users, it is strongly recom-
mended to use MTU 1492. If you are having some difficulties, perform the fol-
lowing steps:
13. The firmware upgrade failed, and/or the Diag LED is flashing.
The upgrade could have failed for a number of reasons. Follow these steps to
upgrade the firmware and/or make the Diag LED stop flashing:
A. To connect to the Router, go to the web browser, and enter
B. Enter the password, if asked. (The default password is admin.)
C. Click the System tab.
D. Look for the MTU option, and select Manual. In the Size field, enter 1492.
E. Click the Apply button to continue.
A. If the firmware upgrade failed, use the TFTP program (it was downloaded
along with the firmware). Open the pdf that was downloaded along with the
firmware and TFTP program, and follow the pdf’s instructions.
B. Set a static IP address on the PC; refer to “Problem #1, I need to set a stat-
ic IP address.” Use the following IP address settings for the computer you
are using:
IP Address: 192.168.1.50
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
78
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
If your difficulties continue, change the Size to different values. Try this list of
values, one value at a time, in this order, until your problem is solved:
Frequently Asked Questions
1462
1400
1362
1300
What is the maximum number of IP addresses that the Router will support?
The Router will support up to 253 IP addresses.
Is IPSec Pass-Through supported by the Router?
Yes, it is a built-in feature that the Router automatically enables.
16. The Diag LED stays lit continuously.
• The Diag LED lights up when the device is first powered up. Meantime,
the system will boot up itself and check for proper operation. After fin-
ishing the checking procedure, the LED turns off to show that the system
is working fine. If the LED remains lit after this time, the device is not
working properly. Try to flash the firmware by assigning a static IP
address to the computer, and then upgrade the firmware. Try using the
following settings, IP Address: 192.168.1.50 and Subnet Mask:
255.255.255.0.
Where is the Router installed on the network?
In a typical environment, the Router is installed between the cable/DSL modem
and the LAN. Plug the Router into the cable/DSL modem’s Ethernet port.
Does the Router support IPX or AppleTalk?
No. TCP/IP is the only protocol standard for the Internet and has become the
global standard for communications. IPX, a NetWare communications protocol
used only to route messages from one node to another, and AppleTalk, a com-
munications protocol used on Apple and Macintosh networks, can be used for
LAN to LAN connections, but those protocols cannot connect from the Internet
to a LAN.
17. When I enter a URL or IP address, I get a time-out error or am prompted to retry.
• Check if other PCs work. If they do, ensure that your workstation’s IP set-
tings are correct (IP Address, Subnet Mask, Default Gateway, and DNS).
Restart the computer that is having a problem.
Does the Internet connection of the Router support 100Mbps Ethernet?
The Router’s current hardware design supports up to 100Mbps Ethernet on its
Internet port; however, the Internet connection speed will vary depending on
the speed of your broadband connection. The Router also supports 100Mbps
over the auto-sensing Fast Ethernet 10/100 switch on the LAN side of the
Router.
• If the PCs are configured correctly, but still not working, check the
Router. Ensure that it is connected and powered on. Connect to it and
check its settings. (If you cannot connect to it, check the LAN and power
connections.)
• If the Router is configured correctly, check your Internet connection
(DSL/cable modem, etc.) to see if it is working correctly.You can remove
the Router to verify a direct connection.
What is Network Address Translation and what is it used for?
• Manually configure the TCP/IP settings with a DNS address provided by
your ISP.
Network Address Translation (NAT) translates multiple IP addresses on the pri-
vate LAN to one public address that is sent out to the Internet. This adds a level
of security since the address of a PC connected to the private LAN is never
transmitted on the Internet. Furthermore, NAT allows the Router to be used
with low cost Internet accounts, such as DSL or cable modems, when only one
TCP/IP address is provided by the ISP. The user may have many private
addresses behind this single address provided by the ISP.
• Make sure that your browser is set to connect directly and that any dial-
up is disabled. For Internet Explorer, click Tools, Internet Options, and
then the Connection tab. Make sure that Internet Explorer is set to Never
dial a connection. For Netscape Navigator, click Edit, Preferences,
Advanced, and Proxy. Make sure that Netscape Navigator is set to
Direct connection to the Internet.
Does the Router support any operating system other than Windows 95, Windows
98, Windows Millennium, Windows 2000, Windows NT, or Windows XP?
Yes, but Linksys does not, at this time, provide technical support for setup, con-
figuration or troubleshooting of any non-Windows operating systems.
18. The Full/Col LED keeps flickering continuously.
• Check the Category 5 Ethernet network cable and its RJ-45 connectors.
• There may be interference with other network devices. Try removing
other PCs or network devices to see if the problem persists. Eliminate
each network device one at a time to determine the cause.
80
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Properties tab.) Make sure that your proxy setting is disabled in the browser.
Does the Router support ICQ send file?
Yes, with the following fix: click ICQ menu -> preference -> connections
tab->, and check I am behind a firewall or proxy. Then set the firewall time-
out to 80 seconds in the firewall setting. The Internet user can then send a file
to a user behind the Router.
If all else fails in the installation, what can I do?
Reset the Router by holding down the reset button until the Diag LED fully
turns on and off. Reset your cable or DSL modem by powering the unit off and
then on. Obtain and flash the latest firmware release that is readily available
I set up an Unreal Tournament Server, but others on the LAN cannot join. What do
I need to do?
If you have a dedicated Unreal Tournament server running, you need to create
a static IP for each of the LAN computers and forward ports 7777, 7778, 7779,
7780, 7781, and 27900 to the IP address of the server. You can also use a port
forwarding range of 7777 ~ 27900. If you want to use the UT Server Admin,
forward another port. (Port 8080 usually works well but is used for remote
admin. You may have to disable this.) Then in the [UWeb.WebServer] section
of the server.ini file, set the ListenPort to 8080 (to match the mapped port
above) and ServerName to the IP assigned to the Router from your ISP.
How will I be notified of new Router firmware upgrades?
All Linksys firmware upgrades are posted on the Linksys website at
www.linksys.com, where they can be downloaded for free. To upgrade the
Router’s firmware, use the Help tab of the Router’s web-based utility. If the
Router’s Internet connection is working well, there is no need to download a
newer firmware version, unless that version contains new features that you
would like to use. Downloading a more current version of Router firmware
will not enhance the quality or speed of your Internet connection, and may dis-
rupt your current connection stability.
Can multiple gamers on the LAN get on one game server and play simultaneously
with just one public IP address?
It depends on which network game or what kind of game server you are using.
Will the Router function in a Macintosh environment?
For example, Unreal Tournament supports multi-login with one public IP.
Yes, but the Router’s setup pages are accessible only through Internet Explorer
4.0 or Netscape Navigator 4.0 or higher for Macintosh.
How do I get Half-Life: Team Fortress to work with the Router?
The default client port for Half-Life is 27005. The computers on your LAN
need to have “+clientport 2700x” added to the HL shortcut command line; the
x would be 6, 7, 8, and on up. This lets multiple computers connect to the same
server. One problem: Version 1.0.1.6 won’t let multiple computers with the
same CD key connect at the same time, even if on the same LAN (not a prob-
lem with 1.0.1.3). As far as hosting games, the HL server does not need to be
in the DMZ. Just forward port 27015 to the local IP address of the server com-
puter.
I am not able to get the web configuration screen for the Router. What can I do?
You may have to remove the proxy settings on your Internet browser, e.g.,
Netscape Navigator or Internet Explorer. Or remove the dial-up settings on
your browser. Check with your browser documentation, and make sure that
sure that your browser is set to connect directly and that any dial-up is disabled.
For Internet Explorer, click Tools, Internet Options, and then the Connection
tab. Make sure that Internet Explorer is set to Never dial a connection. For
Netscape Navigator, click Edit, Preferences, Advanced, and Proxy. Make
sure that Netscape Navigator is set to Direct connection to the Internet.
How can I block corrupted FTP downloads?
If you are experiencing corrupted files when you download a file with your FTP
What is DMZ Hosting?
client, try using another FTP program.
Demilitarized Zone (DMZ) allows one IP address (computer) to be exposed to
the Internet. Some applications require multiple TCP/IP ports to be open. It is
recommended that you set your computer with a static IP if you want to use
DMZ Hosting. To get the LAN IP address, see “Appendix D: Finding the MAC
Address and IP Address for Your Ethernet Adapter.”
The web page hangs; downloads are corrupt, or nothing but junk characters are
being displayed on the screen. What do I need to do?
Force your Ethernet adapter to 10Mbps or half duplex mode, and turn off the
“Auto-negotiate” feature of your Ethernet adapter as a temporary measure.
(Please look at the Network Control Panel in your Ethernet adapter’s Advanced
82
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
If DMZ Hosting is used, does the exposed user share the public IP with the Router?
What is the IEEE 802.11a standard?
No.
It is one of the IEEE standards for wireless networks. The 802.11a standard
allows wireless networking hardware from different manufacturers to commu-
nicate, provided that the hardware complies with the 802.11a standard. The
802.11a standard states a maximum data transfer rate of 54Mbps and an oper-
ating frequency of 5GHz.
Does the Router pass PPTP packets or actively route PPTP sessions?
The Router allows PPTP packets to pass through, supporting up to five ses-
sions.
Is the Router cross-platform compatible?
What is the IEEE 802.11b standard?
Any platform that supports Ethernet and TCP/IP is compatible with the Router.
It is one of the IEEE standards for wireless networks. The 802.11b standard
allows wireless networking hardware from different manufacturers to commu-
nicate, provided that the hardware complies with the 802.11b standard. The
802.11b standard states a maximum data transfer rate of 11Mbps and an oper-
ating frequency of 2.4GHz.
How many ports can be simultaneously forwarded?
Theoretically, the Router can establish 520 sessions at the same time, but you
can only forward 10 ranges of ports.
What IEEE 802.11a features are supported?
Does the Router replace a modem? Is there a cable or DSL modem in the Router?
The product supports the following IEEE 802.11a functions:
No, the Router must work in conjunction with a cable or DSL modem.
•
•
•
•
•
•
•
OFDM protocol
Multi-Channel Roaming
Automatic Rate Selection
RTS/CTS feature
Fragmentation
Transmission Power Control
Dynamic Frequency Selection
Which modems are compatible with the Router?
The Router is compatible with virtually any cable or DSL modem that supports
Ethernet.
What are the advanced features of the Router?
The Router’s advanced features include Advanced Wireless settings, Filtering,
Port Forwarding, Routing, DMZ Hosting, and MAC Address Cloning.
What IEEE 802.11b features are supported?
The product supports the following IEEE 802.11b functions:
How can I check whether I have static or DHCP IP Addresses?
•
•
•
•
•
•
CSMA/CA plus Acknowledge protocol
Multi-Channel Roaming
Automatic Rate Selection
RTS/CTS feature
Fragmentation
Power Management
Consult your ISP to obtain this information.
How do I get mIRC to work with the Router?
Under the Port Forwarding tab, set port forwarding to 113 for the PC on which
you are using mIRC.
Can the Router act as my DHCP server?
Yes. The Router has DHCP server software built-in.
What is ad-hoc mode?
When a wireless network is set to ad-hoc mode, the wireless-equipped com-
puters are configured to communicate directly with each other. The ad-hoc
wireless network will not communicate with any wired network.
Can I run an application from a remote computer over the wireless network?
This will depend on whether or not the application is designed to be used over
a network. Consult the application’s documentation to determine if it supports
operation over a network.
What is infrastructure mode?
When a wireless network is set to infrastructure mode, the wireless network is
configured to communicate with a wired network through a wireless access
point.
84
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
noise. There are two main alternatives, Direct Sequence Spread Spectrum
(DSSS) and Frequency Hopping Spread Spectrum (FHSS).
What is roaming?
Roaming is the ability of a portable computer user to communicate continu-
ously while moving freely throughout an area greater than that covered by a sin-
gle access point. Before using the roaming function, the workstation must make
sure that it is the same channel number with the access point of dedicated cov-
erage area.
What is DSSS? What is FHSS? And what are their differences?
Frequency-Hopping Spread-Spectrum (FHSS) uses a narrowband carrier that
changes frequency in a pattern that is known to both transmitter and receiver.
Properly synchronized, the net effect is to maintain a single logical channel. To
an unintended receiver, FHSS appears to be short-duration impulse noise.
Direct-Sequence Spread-Spectrum (DSSS) generates a redundant bit pattern
for each bit to be transmitted. This bit pattern is called a chip (or chipping
code). The longer the chip, the greater the probability that the original data can
be recovered. Even if one or more bits in the chip are damaged during trans-
mission, statistical techniques embedded in the radio can recover the original
data without the need for retransmission. To an unintended receiver, DSSS
appears as low power wideband noise and is rejected (ignored) by most nar-
rowband receivers.
To achieve true seamless connectivity, the wireless LAN must incorporate a
number of different functions. Each node and access point, for example, must
always acknowledge receipt of each message. Each node must maintain contact
with the wireless network even when not actually transmitting data. Achieving
these functions simultaneously requires a dynamic RF networking technology
that links access points and nodes. In such a system, the user’s end node under-
takes a search for the best possible access to the system. First, it evaluates such
factors as signal strength and quality, as well as the message load currently
being carried by each access point and the distance of each access point to the
wired backbone. Based on that information, the node next selects the right
access point and registers its address. Communications between end node and
host computer can then be transmitted up and down the backbone.
Will the information be intercepted while it is being transmitted through the air?
WLAN features two-fold protection in security. On the hardware side, as with
Direct Sequence Spread Spectrum technology, it has the inherent security fea-
ture of scrambling. On the software side, WLAN offers the encryption function
(WEP) to enhance security and access control.
As the user moves on, the end node’s RF transmitter regularly checks the sys-
tem to determine whether it is in touch with the original access point or whether
it should seek a new one. When a node no longer receives acknowledgment
from its original access point, it undertakes a new search. Upon finding a new
access point, it then re-registers, and the communication process continues.
What is WEP?
WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 64-bit
or 128-bit shared key algorithm, as described in the IEEE 802.11 standard.
What is ISM band?
The FCC and their counterparts outside of the U.S. have set aside bandwidth
for unlicensed use in the ISM (Industrial, Scientific and Medical) band.
Spectrum in the vicinity of 2.4 GHz, in particular, is being made available
worldwide. This presents a truly revolutionary opportunity to place convenient
high-speed wireless capabilities in the hands of users around the globe.
What is a MAC Address?
The Media Access Control (MAC) address is a unique number assigned by the
manufacturer to any Ethernet networking device, such as a network adapter,
that allows the network to identify it at the hardware level. For all practical pur-
poses, this number is usually permanent. Unlike IP addresses, which can
change every time a computer logs onto the network, the MAC address of a
device stays the same, making it a valuable identifier for the network.
What is Spread Spectrum?
Spread Spectrum technology is a wideband radio frequency technique devel-
oped by the military for use in reliable, secure, mission-critical communica-
tions systems. It is designed to trade off bandwidth efficiency for reliability,
integrity, and security. In other words, more bandwidth is consumed than in the
case of narrowband transmission, but the trade-off produces a signal that is, in
effect, louder and thus easier to detect, provided that the receiver knows the
parameters of the spread-spectrum signal being broadcast. If a receiver is not
tuned to the right frequency, a spread-spectrum signal looks like background
How do I avoid interference?
If you are using the Router and one or more Access Points in close proximity
to one another, and they are set on the same channel, interference will be gen-
erated. To avoid interference, be sure to set the Router and all Access Points to
different channels (frequencies); in other words, assign a unique channel to the
Router and each Access Point.
86
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
How do I reset the Router?
Press the Reset button on the back panel for about ten seconds. This will reset
the Router to its default settings.
Appendix B: How to Ping Your ISP’s
E-mail & Web Addresses
Virtually all Internet addresses are configured with words or characters (e.g.,
addresses are assigned to IP addresses, which are the true addresses on the
change). Type it into your web browser and you will wind up at the Linksys
home page every time. There are servers that translate the URL to an IP
address; this is called the Domain Name System (DNS).
How do I resolve issues with signal loss?
There is no way to know the exact range of your wireless network without test-
ing. Every obstacle placed between the Router and a wireless PC will create
signal loss. Lead glass, metal, concrete floors, water and walls will inhibit the
signal and reduce range. Start with the Router and your wireless PC in the
same room and move it away in small increments to determine the maximum
range in your environment.
You may also try using different channels, as this may eliminate interference
affecting only one channel. Also, due to FCC regulations, more power may be
transmitted, using 802.11a, on channels 52, 56, 60 and 64, than on the lower
channels. Lastly, click the Advanced tab of the web-based utility and make
sure that FULL is selected in the Transmission Power field.
IP and web addresses, however, can sometimes be long and hard to remember.
Because of this, certain ISPs will shorten their server addresses to single words
or codes on their users’ web browser or e-mail configurations. If your ISP’s e-
mail and web server addresses are configured with single words (www, e-mail,
home, pop3, etc.) rather than whole Internet addresses or IP addresses, the
Router may have problems sending or receiving mail and accessing the
Internet. This happens because the Router has not been configured by your ISP
to accept their abbreviated server addresses.
I have excellent signal strength, but I cannot see my network.
WEP is probably enabled on the Router, but not on your wireless adapter (or
vice versa). Verify that the same WEP keys and levels (64, 128, or 152) are
being used on all nodes of your wireless network.
The solution is to determine the true web addresses behind your ISPs code
words. You can determine the IP and web addresses of your ISP’s servers by
“pinging” them.
How many channels/frequencies are available with the Router?
Using 802.11a, there are eight available channels, ranging from 36 to 64.
Using 802.11g-draft, there are eleven available channels, ranging from 1 to 11.
Important: If you don’t have your ISP’s web and e-mail IP
addresses, you must either get them from your ISP or follow these
steps prior to connecting the Router to your network.
What is the difference in range
between 802.11a and 802.11g
products?
Overall, range will be a little
less in a typical environment,
and while higher speeds may be
achieved with 802.11a, through-
put degrades more quickly. (See
Figure A-1.)
Figure A-1
If your questions are not addressed here, refer to the Linksys website,
88
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Step Two: Pinging for a Web Address
Step One: Pinging an IP Address
The first step to determining your ISP’s web and e-mail server address is to
ping its IP address.
While the IP address returned above would work as your e-mail server address,
it may not be permanent. IP addresses change all the time. Web addresses, how-
ever, usually don’t. Because of this, you’re likely to have fewer problems by
configuring your system with web addresses rather than IP addresses. Follow
the instructions below to find the web address assigned to the IP address you
just pinged.
1. Power on the computer and the cable or DSL modem, and restore the net-
work configuration set by your ISP if you have since changed it.
2. Click Start and then Run. Type command in the Open field. This will
bring up the DOS window.
1. At the DOS command prompt, type ping -a 24.53.32.4, where 24.53.32.4
is the IP address you just pinged. Information such as the following data
will be displayed.
3. At the DOS command prompt, type ping mail (assuming that the location
for which you’re trying to find an IP address is configured as mail). Press
the Enter key. Information such as the following data, taken from a ping of
Microsoft Network’s e-mail server, will be displayed.
C:\>ping -a 24.53.32.4
Pinging mail.msnv3.occa.home.com [24.53.32.4] with
32 bytes of data:
C:\>ping mail
Pinging mail [24.53.32.4] with 32 bytes of data:
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=127
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Reply from 24.53.32.4: bytes=32 time<10ms TTL=128
Ping statistics for 24.53.32.4:
Packets: Sent = 4, Received = 4, Lost = 0 (0%
loss),
Ping statistics for 24.53.32.4:
Packets: Sent = 4, Received = 4, Lost = 0 (0%
loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
Figure B-2
2. Write down the web address returned by the ping command. (In the exam-
ple in Figure C-2, mail.msnv3.occa.home.com is the web address.) This
web address is the web address assigned to the IP address you just pinged.
While the IP address of mail could conceivably change, it is likely that this
web address will not.
Figure B-1
4. Write down the IP address returned by the ping command (in the example
above: 24.53.32.4.). This IP address is the actual IP address of the server
mail, or any other word or value you have pinged.
3. Replace your ISP’s abbreviated server address with this extended web
address in the corresponding Internet application (web browser, e-mail
application, etc.).
Once you have replaced the brief server address with the true server address,
the Router should have no problem accessing the Internet through that Internet
application.
90
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
There are two types of WEP encryption for 802.1x, static and dynamic. Static
WEP keys are more vulnerable and can only be changed manually on all
devices, including the Router. If you are using MD5 authentication, then you
can only use static WEP keys. Dynamic WEP keys are keys that are renewed
automatically on a periodic basis. This makes the WEP key(s) more difficult to
break, so network security is strengthened. To enable dynamic WEP keys, you
must use 802.1x certificate-based authentication methods, such as TLS or
TTLS.
Appendix C: Configuring Wireless
Security
Background
The Router offers two wireless security features. The basic feature is Wired
Equivalent Privacy (WEP) encryption, an encryption method used to protect
your wireless data communications. WEP uses 64-bit, 128-bit, or 152-bit keys
to provide access control to your network and encryption security for every
data transmission. To decode a data transmission, each point in a network must
use an identical key. Higher encryption levels mean higher levels of security,
but due to the complexity of the encryption, they may mean decreased network
performance.
WEP Encryption
Make sure your wireless network is functioning before attempting to configure
WEP encryption.
On a wireless network, a 128-bit WEP encrypted device will NOT communi-
cate with a 64-bit WEP encrypted device. Therefore, make sure that all of the
wireless devices on each network are using the same encryption level.
You may also have heard the term “40-bit” used in conjunction with WEP
encryption. This is simply another term for 64-bit WEP encryption. This level
of WEP encryption has been called 40-bit because it uses a 40-bit secret key
along with a 24-bit Initialization Vector (40 + 24 = 64). Wireless vendors may
use either name. Linksys uses the term “64-bit” when referring to this level of
encryption.
In addition to enabling WEP, Linksys also recommends the following security
implementations:
• Change the SSID from the default “linksys”
• Change the SSID on a regular basis
• Change the WEP key regularly
• Enable MAC address filtering (if your wireless products allow it)
Note: WEP encryption is an additional data security measure and not
essential for router operation; however, Linksys recommends the use
of WEP encryption.
For instructions on how to configure the Router’s WEP settings, go to the
“Setup” section of “Chapter 7: The Router’s Web-Based Utility.” For instruc-
tions on how to configure the WEP settings of your PC’s wireless adapter, refer
to your wireless adapter’s documentation.
The second wireless security feature is 802.1x. The IEEE 802.1x standard spec-
ifies authentication methods for a wireless client, such as a PC, to access a net-
work, so network security is enhanced. Based on the Extensible Authentication
Protocol (EAP), 802.1x designates how a client accesses a network server, fre-
quently a RADIUS server, with the Router acting as an authenticator. When a
network uses 802.1x, the identity of the client is verified before the client is
allowed network access.
For example, a wireless user may use one of the authentication methods to
access a wireless network protected by an authentication server. The user’s PC
sends a request to the Router (an access point can be used instead). The Router
sends an identification request back to the PC. After the PC sends the Router the
identification message, the Router forwards the identification message to the
server. If the server accepts the identification message, then the PC is permitted
access to the wireless network.
92
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
3. Write down the Adapter Address as shown on your computer screen (see
Figure E-3). This is the MAC address for your Ethernet adapter and will
be shown as a series of numbers and letters.
Appendix D: Finding the MAC
Address and IP Address for Your
Ethernet Adapter
The MAC address/Adapter Address is what you will use for MAC address
cloning or MAC filtering.
This section describes how to find the MAC address for your Ethernet adapter
to do either MAC address filtering or MAC address cloning for the Router and
ISP. You can also find the IP address of your computer’s Ethernet adapter. The
IP address is used for filtering, forwarding, and DMZ. Follow the steps in this
appendix to find the MAC address or IP address for your adapter in Windows
95, 98, Me, NT, 2000, and XP.
For Windows 95, 98, and Me:
1. Click on Start and Run. In the Open field, enter winipcfg. Then press the
Enter key or the OK button.
Figure D-3
Write down the IP Address as shown on your computer screen. The exam-
ple in Figure E-3 shows the IP address of your Ethernet adapter as
192.168.1.100. Your computer may show something different.
Note: The MAC address is also called the Adapter
Address.
Figure D-1
For Windows NT, 2000, and XP:
2. When the IP Configuration window appears, select the Ethernet adapter
you are using to connect to the Router via a Category 5 Ethernet network
cable.
1. Click Start and Run. In the Open field, enter cmd. Press the Enter key or
click the OK button.
Figure D-4
Figure D-2
94
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
2. In the command prompt, enter ipconfig /all. Then press the Enter key.
Appendix E: Glossary
802.11a - One of the IEEE standards for wireless networking hardware.
Products that adhere to a specific IEEE standard will work with each other,
even if they are manufactured by different companies. It specifies a maximum
data transfer rate of 54Mbps and an operating frequency of 5GHz. The 802.11a
standard uses the Orthogonal Frequency Division Multiplexing (OFDM) trans-
mission method. Additionally, the 802.11a standard supports 802.11 features
such as WEP encryption for security.
802.11b - One of the IEEE standards for wireless networking hardware.
Products that adhere to a specific IEEE standard will work with each other,
even if they are manufactured by different companies. The 802.11b standard
specifies a maximum data transfer rate of 11Mbps, an operating frequency of
2.4GHz, and WEP encryption for security. 802.11b networks are also referred
to as Wi-Fi networks.
802.11g - A proposed, but as yet unratified extension of the IEEE 802.11 stan-
dard for wireless networking hardware. The draft 802.11g specifications used
by Linksys specify a maximum data transfer rate of 54Mbps using OFDM
modulation, an operating frequency of 2.4GHz, backward compatibility with
IEEE 802.11b devices, and WEP encryption for security.
Figure D-5
3. Write down the Physical Address as shown on your computer screen; it is
the MAC address for your Ethernet adapter. This will appear as a series of
letters and numbers.
802.1x - Based on the Extensible Authentication Protocol (EAP), the 802.1x
standard is one of the IEEE standards for network authentication and key man-
agement. It establishes a framework that supports multiple authentication meth-
ods. This standard can be incorporated into any type of network to enhance its
security.
The MAC address/Physical Address is what you will use for MAC address
cloning or MAC filtering.
Note: The MAC address is also called the Physical
Address.
For example, a wireless user may use one of the authentication methods to
access a wireless network protected by an authentication server. The user, also
called the supplicant, sends a request to an access point or wireless router, also
called the authenticator. The authenticator sends an identification request back
to the user. After the user sends the authenticator the identification message,
the authenticator forwards the user's identification message to the authentica-
tion server. If the server accepts the identification message, then the user is per-
mitted access to the wireless network. The 802.1x standard can also support
encryption key management to strengthen wireless network encryption servic-
es.
Write down the IP Address as shown on your computer screen. The exam-
ple in Figure E-5 shows the IP address of your Ethernet adapter as
192.168.1.100. Your computer may show something different.
96
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Adapter - Printed circuit board that plugs into a PC to add to capabilities or
connectivity to a PC. In a networked environment, a network interface card is
the typical adapter that allows the PC or server to connect to the intranet and/or
Internet.
Backbone - The part of a network that connects most of the systems and net-
works together and handles the most data.
Bandwidth - The transmission capacity of a given facility, in terms of how
much data the facility can transmit in a fixed amount of time; expressed in bits
per second (bps).
Ad-hoc Network - An ad-hoc network is a group of computers, each with a
wireless adapter, connected as an independent 802.11 wireless LAN. Ad-hoc
wireless computers operate on a peer-to-peer basis, communicating directly
with each other without the use of an access point. Ad-hoc mode is also
referred to as an Independent Basic Service Set or as peer-to-peer mode.
Beacon Interval - A beacon is a packet broadcast by the Access Point to keep
the network synchronized. A beacon includes the wireless LAN service area,
the AP address, the Broadcast destination addresses, a time stamp, Delivery
Traffic Indicator Maps, and the Traffic Indicator Message (TIM).
ADSL (Asymmetric Digital Subscriber Line) - A technology for transmitting
digital information at a high bandwidth on existing phone lines to homes and
businesses. Unlike regular dialup phone service, ADSL provides continuously-
available, "always on" connection. ADSL is asymmetric in that it uses most of
the channel to transmit downstream to the user and only a small part to receive
information from the user. ADSL simultaneously accommodates analog (voice)
information on the same line. ADSL is generally offered at downstream data
rates from 144 Kbps to about 6 Mbps. A form of ADSL, known as Universal
ADSL or G.lite, has been approved as a standard by the ITU-TS.
Bit - A binary digit. The value - 0 or 1-used in the binary numbering system.
Also, the smallest form of data.
Boot - To cause the computer to start executing instructions. Personal comput-
ers contain built-in instructions in a ROM chip that are automatically executed
on startup. These instructions search for the operating system, load it and pass
control to it.
Broadband - A data-transmission scheme in which multiple signals share the
bandwidth of a medium. This allows the transmission of voice, data and video
signals over a single medium. Cable television uses broadband techniques to
deliver dozens of channels over one cable.
ADSL was specifically designed to exploit the one-way nature of most multi-
media communication in which large amounts of information flow toward the
user and only a small amount of interactive control information is returned.
Several experiments with ADSL to real users began in 1996. In 1998, wide-
scale installations began in several parts of the U.S. In 2000 and beyond, ADSL
and other forms of DSL are expected to become generally available in urban
areas. With ADSL (and other forms of DSL), telephone companies are com-
peting with cable companies and their cable modem services.
Browser - A browser is an application program that provides a way to look at
and interact with all the information on the World Wide Web or PC. The word
"browser" seems to have originated prior to the Web as a generic term for user
interfaces that let you browse text files online.
AppleTalk - An Apple Computer networking system that supports Apple's pro-
prietary local talk.
Buffer - A buffer is a shared or assigned memory area used by hardware
devices or program processes that operate at different speeds or with different
sets of priorities. The buffer allows each device or process to operate without
being held up by the other. In order for a buffer to be effective, the size of the
buffer and the algorithms for moving data into and out of the buffer need to be
considered by the buffer designer. Like a cache, a buffer is a "midpoint holding
place" but exists not so much to accelerate the speed of an activity as to sup-
port the coordination of separate activities.
Auto-MDI/MDIX - On a network hub or switch, an auto-MDI/MDIX port
automatically senses if it needs to act as a MDI or MDIX port. The auto-
MDI/MDIX capability eliminates the need for crossover cables.
Auto-negotiate - To automatically determine the correct settings. The term is
often used with communications and networking. For example, Ethernet
10/100 cards, hubs and switches can determine the highest speed of the node
they are connected to and adjust their transmission rate accordingly.
Cable Modem - A device that connects a computer to the cable television net-
work, which in turn connects to the Internet. Once connected, cable modem
users have a continuous connection to the Internet. Cable modems feature
98
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
asymmetric transfer rates: around 36 Mbps downstream (from the Internet to
the computer), and from 200 Kbps to 2 Mbps upstream (from the computer to
the Internet).
protocol (TCP/IP), each machine that can connect to the Internet needs a
unique IP address. When an organization sets up its computer users with a con-
nection to the Internet, an IP address must be assigned to each machine.
Without DHCP, the IP address must be entered manually at each computer and,
if computers move to another location in another part of the network, a new IP
address must be entered. DHCP lets a network administrator supervise and dis-
tribute IP addresses from a central point and automatically sends a new IP
address when a computer is plugged into a different place in the network.
CAT 5 - ANSI/EIA (American National Standards Institute/Electronic
Industries Association) Standard 568 is one of several standards that specify
"categories" (the singular is commonly referred to as "CAT") of twisted pair
cabling systems (wires, junctions, and connectors) in terms of the data rates
that they can sustain. CAT 5 cable has a maximum throughput of 100 Mbps and
is usually utilized for 100BaseTX networks.
DHCP uses the concept of a "lease" or amount of time that a given IP address
will be valid for a computer. The lease time can vary depending on how long a
user is likely to require the Internet connection at a particular location. It's espe-
cially useful in education and other environments where users change fre-
quently. Using very short leases, DHCP can dynamically reconfigure networks
in which there are more computers than there are available IP addresses.
Cookie - Data created by a Web server that is stored on a user's computer. It
provides a way for the Web site to keep track of a user's patterns and prefer-
ences and, with the cooperation of the Web browser, to store them on the user's
own hard disk.
CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) - In local
area networking, this is the CSMA technique that combines slotted time-divi-
sion multiplexing with carrier sense multiple access/collision detection
(CSMA/CD) to avoid having collisions occur a second time. This works best if
the time allocated is short compared to packet length and if the number of sit-
uations is small.
DHCP supports static addresses for computers containing Web servers that
need a permanent IP address.
DMZ (Demilitarized Zone) - Allows one IP address (or computer) to be
exposed to the Internet. Some applications require multiple TCP/IP ports to be
open. You should set your computer with a static IP address if you want to use
DMZ Hosting.
CTS (Clear To Send) - An RS-232 signal sent from the receiving station to the
transmitting station that indicates it is ready to accept data.
DNS - The domain name system (DNS) is the way that Internet domain name
are located and translated into Internet Protocol (IP) addresses. A domain name
is a meaningful and easy-to-remember "handle" for an Internet address.
Daisy Chain - Connected in series, one after the other. Transmitted signals go
to the first device, then to the second and so on.
Domain - A subnetwork comprised of a group of clients and servers under the
control of one security database. Dividing LANs into domains improves per-
formance and security.
DDNS (Dynamic Domain Name System) - Allows a network device with a
dynamic Internet IP address to have a fixed host and domain name, such as
myhostname.mydomainname.com. It is useful when you are hosting your own
website, FTP server, or other server behind a router, so people can find your
site no matter how often the Internet IP address changes. Using DDNS requires
registering with a DDNS service provider on the Internet.
Download - To receive a file transmitted over a network. In a communications
session, download means receive, upload means transmit.
DSL (Digital Subscriber Line) - A technology that dramatically increases the
digital capacity of ordinary telephone lines into the home or office and, by
employing unused bandwidth, still allows for normal phone usage. DSL pro-
vides "always-on" operation, eliminating the need to dial in to the service.
Default Gateway - The routing device used to forward all traffic that is not
addressed to a station within the local subnet.
DHCP (Dynamic Host Configuration Protocol) - A protocol that lets network
administrators manage centrally and automate the assignment of Internet
Protocol (IP) addresses in an organization's network. Using the Internet's set of
DSSS (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit
pattern for all data transmitted. This bit pattern is called a chip (or chipping
100
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
code). Even if one or more bits in the chip are damaged during transmission,
statistical techniques embedded in the receiver can recover the original data
without the need for retransmission. To an unintended receiver, DSSS appears
as low power wideband noise and is rejected (ignored) by most narrowband
receivers. However, to an intended receiver (i.e. another wireless LAN end-
point), the DSSS signal is recognized as the only valid signal, and interference
is inherently rejected (ignored).
FHSS (Frequency Hopping Spread Spectrum) - FHSS continuously changes
(hops) the carrier frequency of a conventional carrier several times per second
according to a pseudo-random set of channels. Because a fixed frequency is not
used, and only the transmitter and receiver know the hop patterns, interception
of FHSS is extremely difficult.
Finger - A UNIX command widely used on the Internet to find out informa-
tion about a particular user, such as telephone number, whether currently
logged on or the last time logged on. The person being "fingered" must have
placed his or her profile on the system. Fingering requires entering the full
user@domain address.
DTIM (Delivery Traffic Indication Message) - A DTIM field is a countdown
field informing clients of the next window for listening to broadcast and mul-
ticast messages. When the AP has buffered broadcast or multicast messages for
associated clients, it sends the next DTIM with a DTIM Interval value. AP
Clients hear the beacons and awaken to receive the broadcast and multicast
messages.
Firewall - A firewall is a set of related programs, located at a network gateway
server, that protects the resources of a network from users from other networks.
(The term also implies the security policy that is used with the programs.) An
enterprise with an intranet that allows its workers access to the wider Internet
installs a firewall to prevent outsiders from accessing its own private data
resources and for controlling what outside resources to which its own users
have access.
Dynamic IP Address - An IP address that is automatically assigned to a client
station in a TCP/IP network, typically by a DHCP server. Network devices that
serve multiple users, such as servers and printers, are usually assigned static IP
addresses.
Dynamic Routing - The ability for a router to forward data via a different route
based on the current conditions of the communications circuits. For example,
it can adjust for overloaded traffic or failing lines and is much more flexible
than static routing, which uses a fixed forwarding path.
Basically, a firewall, working closely with a router, examines each network
packet to determine whether to forward it toward its destination.
Firmware - Code that is written onto read-only memory (ROM) or program-
mable read-only memory (PROM). Once firmware has been written onto the
ROM or PROM, it is retained even when the device is turned off.
EAP (Extensible Authentication Protocol) - An IETF standard that establishes
an authentication protocol for network access. Many authentication methods,
including passwords, certificates, and smart cards, work within this framework.
Fragmentation - Breaking a packet into smaller units when transmitting over
a network medium that cannot support the original size of the packet.
Encryption - A security method that applies a specific algorithm to data in
order to alter the data's appearance and prevent other devices from reading the
information.
FTP (File Transfer Protocol) - A protocol used to transfer files over a TCP/IP
network (Internet, UNIX, etc.). For example, after developing the HTML pages
for a Web site on a local machine, they are typically uploaded to the Web serv-
er using FTP.
Ethernet - IEEE standard network protocol that specifies how data is placed
on and retrieved from a common transmission medium. Has a transfer rate of
10 Mbps. Forms the underlying transport vehicle used by several upper-level
protocols, including TCP/IP and XNS.
FTP includes functions to log onto the network, list directories and copy files.
It can also convert between the ASCII and EBCDIC character codes. FTP oper-
ations can be performed by typing commands at a command prompt or via an
FTP utility running under a graphical interface such as Windows. FTP transfers
can also be initiated from within a Web browser by entering the URL preceded
with ftp://.
Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet
CSMA/CD network access method.
102
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Unlike e-mail programs in which graphics and program files have to be
"attached," FTP is designed to handle binary files directly and does not add the
overhead of encoding and decoding the data.
The IEEE fosters the development of standards that often become national and
international standards. The organization publishes a number of journals, has
many local chapters, and several large societies in special areas, such as the
IEEE Computer Society.
Full Duplex - The ability of a device or line to transmit data simultaneously in
both directions.
Infrastructure Network - An infrastructure network is a group of computers
or other devices, each with a wireless adapter, connected as an 802.11 wireless
LAN. In infrastructure mode, the wireless devices communicate with each
other and to a wired network by first going through an access point. An infra-
structure wireless network connected to a wired network is referred to as a
Basic Service Set (BSS). A set of two or more BSS in a single network is
referred to as an Extended Service Set (ESS). Infrastructure mode is useful at
a corporation scale, or when it is necessary to connect the wired and wireless
networks.
Gateway - A device that interconnects networks with different, incompatible
communications protocols.
Half Duplex - Data transmission that can occur in two directions over a single
line, but only one direction at a time.
Hardware - Hardware is the physical aspect of computers, telecommunica-
tions, and other information technology devices. The term arose as a way to dis-
tinguish the "box" and the electronic circuitry and components of a computer
from the program you put in it to make it do things. The program came to be
known as the software.
IP (Internet Protocol) - The method or protocol by which data is sent from one
computer to another on the Internet. It is a standard set of rules, procedures, or
conventions relating to the format and timing of data transmission between two
computers that they must accept and use to be able to understand each other.
Hop - The link between two network nodes.
IP Address - In the most widely installed level of the Internet Protocol (IP)
today, an IP address is a 32-binary digit number that identifies each sender or
receiver of information that is sent in packet across the Internet. When you
request an HTML page or send e-mail, the Internet Protocol part of TCP/IP
includes your IP address in the message (actually, in each of the packets if more
than one is required) and sends it to the IP address that is obtained by looking
up the domain name in the Uniform Resource Locator you requested or in the
e-mail address you're sending a note to. At the other end, the recipient can see
the IP address of the Web page requestor or the e-mail sender and can respond
by sending another message using the IP address it received.
HTTP (HyperText Transport Protocol) - The communications protocol used
to connect to servers on the World Wide Web. Its primary function is to estab-
lish a connection with a Web server and transmit HTML pages to the client
browser.
Hub - The device that serves as the central location for attaching wires from
workstations. Can be passive, where there is no amplification of the signals; or
active, where the hubs are used like repeaters to provide an extension of the
cable that connects to a workstation.
ICQ - A conferencing program for the Internet that provides interactive chat,
e-mail and file transfer and can alert you when someone on your predefined list
has also come online.
IPCONFIG - A Windows NT or 2000 utility that provides for querying, defin-
ing and managing IP addresses within a network. A commonly used utility for
configuring networks with static IP addresses.
IEEE (The Institute of Electrical and Electronics Engineers) - The IEEE
describes itself as "the world's largest technical professional society, promoting
the development and application of electrotechnology and allied sciences for
the benefit of humanity, the advancement of the profession, and the well-being
of our members."
IPSec (Internet Protocol Security) - A suite of protocols used to implement
secure exchange of packets at the IP layer. IPSec supports two basic modes:
Transport and Tunnel. Transport encrypts the payload of each packet, leaving
the header untouched, while Tunnel mode encrypts both the header and the pay-
load and is therefore more secure. IPSec must be supported on both transmit-
ter and receiver and must share a public key. Tunnel mode is widely deployed
in VPNs (Virtual Private Networks).
104
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
IPX (Internetwork Packet EXchange) - A NetWare communications protocol
used to route messages from one node to another. IPX packets include network
addresses and can be routed from one network to another.
MDIX (Medium Dependent Interface Crossed) - On a network hub or switch,
a MDIX port connects to a computer using a straight-through cable. To connect
a MDIX port to another hub or switch, use a crossover cable.
ISM band - The FCC and their counterparts outside of the U.S. have set aside
bandwidth for unlicensed use in the ISM (Industrial, Scientific and Medical)
band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made avail-
able worldwide. This presents a truly revolutionary opportunity to place con-
venient high-speed wireless capabilities in the hands of users around the globe.
mIRC - mIRC runs under Windows and provides a graphical interface for log-
ging onto IRC servers and listing, joining and leaving channels.
Multicasting - Sending data to a group of nodes instead of a single destination.
NAT (Network Address Translation) - The translation of an Internet Protocol
address (IP address) used within one network to a different IP address known
within another network. One network is designated the inside network and the
other is the outside.
ISP (Internet Service Provider) - A company that provides individuals and
companies access to the Internet and other related services such as Web site
building and virtual hosting.
LAN (Local Area Network) - A group of computers and associated devices that
share a common communications line and typically share the resources of a
single processor or server within a small geographic area (for example, within
an office building).
Network - A system that transmits any combination of voice, video and/or data
between users.
NNTP (Network News Transfer Protocol) - The protocol used to connect to
Usenet groups on the Internet. Usenet newsreaders support the NNTP protocol.
Layer 2 - Data Link layer in the International Standards Organization (ISO) 7-
Layer Data Communications Protocol, also known as the OSI (Open Systems
Interconnection) model. This is a standard model to consult when designing
network protocols. Layer 2 is directly related to the hardware interface for net-
work devices and passes traffic based on MAC addresses.
Node - A network junction or connection point, typically a computer or work
station.
Notebook (PC) - A notebook computer is a battery-powered personal comput-
er generally smaller than a briefcase that can easily be transported and conve-
niently used in temporary spaces such as on airplanes, in libraries, temporary
offices, and at meetings. A notebook computer, sometimes called a laptop com-
puter, typically weighs less than five pounds and is three inches or less in thick-
ness.
MAC (Media Access Control) Address - A unique number assigned by the
manufacturer to any Ethernet networking device, such as a network adapter,
that allows the network to identify it at the hardware level.
Mbps (Megabits per second) - One million bits per second; unit of measure-
ment for data transmission.
OFDM - Developed for wireless applications, Orthogonal Frequency Division
Multiplexing (OFDM) technology offers superior performance-increased data
rates and more reliable transmissions-than previous technologies, such as
DSSS. OFDM is a scheme in which numerous signals of different frequencies
are combined to form a single signal for transmission on the medium.
MD5 - A type of one-way authentication method that uses passwords. MD5
authentication is not as secure as the EAP-TLS or EAP/TTLS authentication
methods. MD5 authentication does not support dynamic WEP key manage-
ment.
OFDM works by breaking one high-speed data stream into a number of lower-
speed data streams, which are then transmitted in parallel. Each lower speed
stream is used to modulate a subcarrier. Essentially, this creates a multi-carrier
transmission by dividing a wide frequency band or channel into a number of
narrower frequency bands or sub-channels. OFDM is also used for other appli-
cations, including powerline networking.
MDI (Medium Dependent Interface) - On a network hub or switch, a MDI
port, also known as an uplink port, connects to another hub or switch using a
straight-through cable. To connect a MDI port to a computer, use a crossover
cable.
106
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Packet - A unit of data routed between an origin and a destination in a network.
used in 802.1x implementations; however, they are not specified by the 802.1x
standard.
Passphrase - Used much like a password, a passphrase simplifies the WEP
encryption process by automatically generating the WEP encryption keys for
Linksys products.
RJ-45 (Registered Jack-45) - A connector similar to a telephone connector that
holds up to eight wires, used for connecting Ethernet devices.
Ping (Packet INternet Groper) - An Internet utility used to determine whether
a particular IP address is online. It is used to test and debug a network by send-
ing out a packet and waiting for a response.
RMON (Remote MONitoring) - RMON provides comprehensive network
monitoring capabilities. It eliminates the polling required in standard SNMP,
and can set alarms on a variety of traffic conditions, including specific error
types.
POP3 (Post Office Protocol 3) - A standard mail server commonly used on the
Internet. It provides a message store that holds incoming e-mail until users log
on and download it. POP3 is a simple system with little selectivity. All pending
messages and attachments are downloaded at the same time. POP3 uses the
SMTP messaging protocol.
Roaming - In an infrastructure mode wireless network, this refers to the abili-
ty to move out of one access point's range and into another and transparently
reassociate and reauthenticate to the new access point. This reassociation and
reauthentication should occur without user intervention and ideally without
interruption to network connectivity. A typical scenario would be a location
with multiple access points, where users can physically relocate from one area
to another and easily maintain connectivity.
Port - A pathway into and out of the computer or a network device such as a
switch or router. For example, the serial and parallel ports on a personal com-
puter are external sockets for plugging in communications lines, modems and
printers.
Router - Protocol-dependent device that connects subnetworks together.
Routers are useful in breaking down a very large network into smaller subnet-
works; they introduce longer delays and typically have much lower throughput
rates than bridges.
PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a method for the
encapsulation of PPP packets over Ethernet frames from the user to the ISP
over the Internet. One reason PPPoE is preferred by ISPs is because it provides
authentication (username and password) in addition to data transport. A PPPoE
session can be initiated by either a client application residing on a PC, or by
client firmware residing on a modem or router.
RTS (Request To Send) - An RS-232 signal sent from the transmitting station
to the receiving station requesting permission to transmit.
Server - Any computer whose function in a network is to provide user access
PPTP (Point-to-Point Tunneling Protocol) - A protocol which allows the Point
to Point Protocol (PPP) to be tunneled through an IP network. PPTP does not
specify any changes to the PPP protocol but rather describes a "tunneling serv-
ice" for carrying PPP (a tunneling service is any network service enabled by
tunneling protocols such as PPTP, L2F, L2TP, and IPSEC tunnel mode). One
example of a tunneling service is secure access from a remote small office net-
work to a headquarters corporate intranet via a Virtual Private Network (VPN)
that traverses the Internet. However, tunneling services are not restricted to cor-
porate environments and may also be used for personal (i.e., non-business)
applications.
to files, printing, communications, and other services.
SMTP (Simple Mail Transfer Protocol) - The standard e-mail protocol on the
Internet. It is a TCP/IP protocol that defines the message format and the mes-
sage transfer agent (MTA), which stores and forwards the mail.
SNMP (Simple Network Management Protocol) - A widely used network
monitoring and control protocol. Data is passed from SNMP agents, which are
hardware and/or software processes reporting activity in each network device
(hub, router, bridge, etc.) to the workstation console used to oversee the net-
work. The agents return information contained in a MIB (Management
Information Base), which is a data structure that defines what is obtainable
from the device and what can be controlled (turned off, on, etc.).
RADIUS (Remote Authentication Dial-In User Service) - A protocol used to
control network access. RADIUS enables servers to authenticate users, so only
legitimate users are granted network access. RADIUS servers are frequently
108
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Software - Instructions for the computer. A series of instructions that performs
a particular task is called a "program." The two major categories of software are
"system software" and "application software." System software is made up of
control programs such as the operating system and database management sys-
tem (DBMS). Application software is any program that processes data for the
user.
TCP (Transmission Control Protocol) - A method (protocol) used along with
the IP (Internet Protocol) to send data in the form of message units (datagram)
between network devices over a LAN or WAN. While IP takes care of handling
the actual delivery of the data (routing), TCP takes care of keeping track of the
individual units of data (called packets) that a message is divided into for effi-
cient delivery over the network. TCP is known as a "connection oriented" pro-
tocol due to requiring the receiver of a packet to return an acknowledgment of
receipt to the sender of the packet resulting in transmission control.
A common misconception is that software is data. It is not. Software tells the
hardware how to process the data.
TCP/IP (Transmission Control Protocol/Internet Protocol) - The basic com-
munication language or set of protocols for communications over a network
(developed specifically for the Internet). TCP/IP defines a suite or group of
protocols and not only TCP and IP.
Spread Spectrum - Spread Spectrum technology is a wideband radio frequen-
cy technique developed by the military for use in reliable, secure, mission-crit-
ical communications systems. It is designed to trade off bandwidth efficiency
for reliability, integrity, and security. In other words, more bandwidth is con-
sumed than in the case of narrowband transmission, but the trade off produces
a signal that is, in effect, louder and thus easier to detect, provided that the
receiver knows the parameters of the spread-spectrum signal being broadcast.
If a receiver is not tuned to the right frequency, a spread-spectrum signal looks
like background noise. There are two main alternatives, Direct Sequence
Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS).
Telnet - A terminal emulation protocol commonly used on the Internet and
TCP/IP-based networks. It allows a user at a terminal or computer to log onto
a remote device and run a program.
TFTP (Trivial File Transfer Protocol) - A version of the TCP/IP FTP protocol
that has no directory or password capability.
SSID (Service Set IDentifier) - A unique name shared among all points in a
wireless network. The SSID must be identical for each point in the wireless net-
work and is case-sensitive.
Throughput - The amount of data moved successfully from one place to
another in a given time period.
UDP (User Datagram Protocol) - A method (protocol) used along with the IP
(Internet Protocol) to send data in the form of message units (datagram)
between network devices over a LAN or WAN. While IP takes care of handling
the actual delivery of the data (routing), UDP takes care of keeping track of the
individual units of data (called packets) that a message is divided into for effi-
cient delivery over the network. UDP is known as a "connection-less" protocol
due to NOT requiring the receiver of a packet to return an acknowledgment of
receipt to the sender of the packet (as opposed to TCP).
Static IP Address - A permanent IP address that is assigned to a node in an IP
or a TCP/IP network.
Static Routing - Forwarding data in a network via a fixed path. Static routing
cannot adjust to changing line conditions as can dynamic routing.
Storage - The semi-permanent or permanent holding place for digital data.
Subnet Mask - The method used for splitting IP networks into a series of sub-
groups, or subnets. The mask is a binary pattern that is matched up with the IP
address to turn part of the host ID address field into a field for subnets.
Upgrade - To replace existing software or firmware with a newer version.
Upload - To transmit a file over a network. In a communications session,
upload means transmit, download means receive.
Switch - 1. A data switch connects computing devices to host computers,
allowing a large number of devices to share a limited number of ports. 2. A
device for making, breaking, or changing the connections in an electrical cir-
cuit.
URL (Uniform Resource Locator) - The address that defines the route to a file
on the Web or any other Internet facility. URLs are typed into the browser to
access Web pages, and URLs are embedded within the pages themselves to pro-
vide the hypertext links to other pages.
110
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
VPN (Virtual Private Network) - A technique that allows two or more LANs to
be extended over public communication channels by creating private commu-
nication subchannels (tunnels). Effectively, these LANs can use a WAN as a
single large "virtually private" LAN. This removes the need to use leased lines
for WAN communications through secure use of a publicly available WAN
(such as the Internet). Examples of VPN technology are: PPTP (Point to Point
Tunneling Protocol), L2TP (Layer 2 Tunneling Protocol), and IPSec (Internet
Protocol Security).
Appendix F: Specifications
Standards
802.11a, 802.11b, draft 802.11g
Ports
Internet:
LAN:
One 10/100 RJ-45 Port for Cable/DSL Modem
Four 10/100 RJ-45 Switched Ports
WAN (Wide Area Network)- A communications network that covers a rela-
tively large geographic area, consisting of two or more LANs. Broadband com-
munication over the WAN is often through public networks such as the tele-
phone (DSL) or cable systems, or through leased lines or satellites. In its most
basic definition, the Internet could be considered a WAN.
Buttons
One Reset Button and One Power Port
UTP Category 5 or better
Cabling Type
LEDs
Power, Diag
Link/Act, 100
Link/Act, Full/Col, 100
Act, Link
WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-
bit or 128-bit shared key algorithm, as described in the IEEE 802.11 standard.
Internet:
LAN:
802.11a:
54g:
WINIPCFG - Configuration utility based on the Win32 API for querying,
defining and managing IP addresses within a network. A commonly used util-
ity for configuring networks with static IP addresses.
Act, Link
WLAN (Wireless Local Area Network) - A group of computers and associat-
ed devices that communicate with each other wirelessly.
112
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Dual-Band Wireless A+G Broadband Router
Environmental
Appendix G: Warranty Information
BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE
FROM THE PRODUCT'S PACKAGING ON HAND WHEN CALLING.
RETURN REQUESTS CANNOT BE PROCESSED WITHOUT PROOF OF
PURCHASE.
Dimensions
7.32" x 1.89" x 6.89"
(186 mm x 48 mm x 175 mm)
Unit Weight
Power
0.88 lbs. (0.4 kg)
External, 5V DC, 2.5A
IN NO EVENT SHALL LINKSYS’S LIABILITY EXCEED THE PRICE
PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCI-
DENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS
DOCUMENTATION. LINKSYS DOES NOT OFFER REFUNDS FOR ANY
PRODUCT.
Certifications
Operating Temp.
Storage Temp.
FCC, CE Marking, Wi-Fi
32ºF to 104ºF (0ºC to 40ºC)
-4ºF to 158ºF (-20ºC to 70ºC)
LINKSYS OFFERS CROSS SHIPMENTS, A FASTER PROCESS FOR PRO-
CESSING AND RECEIVING YOUR REPLACEMENT. LINKSYS PAYS
FOR UPS GROUND ONLY. ALL CUSTOMERS LOCATED OUTSIDE OF
THE UNITED STATES OF AMERICA AND CANADA SHALL BE HELD
RESPONSIBLE FOR SHIPPING AND HANDLING CHARGES. PLEASE
CALL LINKSYS FOR MORE DETAILS.
Operating Humidity 10% to 85%, Non-Condensing
Storage Humidity 5% to 90%, Non-Condensing
114
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Instant Wireless® Series
Appendix H: Contact Information
For help with the installation or operation of the Dual-Band Wireless A+G
Broadband Router, contact Linksys Technical Support at one of the phone num-
bers or Internet addresses below.
Sales Information
Technical Support
RMA Issues
Fax
800-546-5797 (1-800-LINKSYS)
800-326-7114
949-271-5461
949-265-6655
Email
Web site
FTP site
© Copyright 2003 Linksys, All Rights Reserved.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Roku Computer Monitor BrightSign User Guide
Sagem Modem N56815740110 User Guide
Samsung Automobile Alarm SPF 83H User Guide
Samsung Camcorder AD68 00839H User Guide
Samsung CD Player MAX B420 User Guide
Samsung DVD Player DVD 611 511 User Guide
Sangean Electronics Network Card 381RB01 A User Guide
Seagate Computer Drive ST9816AG User Guide
Sears Lawn Mower 917255741 User Guide
Sears Rowing Machine 35 1215B User Guide