RCA VCR VR661HF User Guide

VCR  
User’s Guide  
Changing Entertainment. Again.  
VR661HF  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Introduction  
Key Features Overview  
Your VCR is equipped with features that will add to your recording and viewing experience.  
The following information summarizes a few of these features. Chapter 4 provides more  
information about the rest of the VCR’s features and how to use them.  
VCR Plus+® SILVER System  
The VCR Plus+ system allows for simple timer recording programming by using  
a single PlusCode® programming number found in most TV program listings.  
The VCR Plus+ SILVER system simplifies timer recordings by automatically  
setting up and updating the VCR’s clock and channel list for you.  
Requirements: Make sure the VCR Plus+ SILVER system is active, and that Auto  
Channel Search and time set features are correct.  
®
This feature uses patented technology that detects and marks most commercials  
on your recordings. The VCR determines where commercials are located, marks  
the beginnings and ends of detected commercial segments, then easily skips  
over them during playback. This feature does not erase commercials from  
the tape.  
®
This feature helps locate the beginning of a purchased or rented movie as well  
as skip thorugh previews. You can go to the beginning of the movie, or, skip  
from one preview/long commercial to the next.  
ONOFF  
TV  
VCR  
Universal Back-Lit Remote Control  
REVERSE  
PLAY  
FORWARD  
RECORD  
INFO  
STOP  
PAUSE  
SEARCH  
Description: The VCR’s remote control can operate most RCA, GE, and Proscan  
TVs with no additional steps. It can be programmed to operate many other  
brands of TVs. Back-lit buttons offer easier control in the dark.  
MUTE  
GO BACK  
SPEED  
CLEAR  
1
MENU  
2
5
8
0
3
4
7
6
9
T
TRACKING  
F.ADV  
Requirements: Point the remote control at the active component and press the  
ON•OFF button to see if it can be operated.  
Rec  
Ch 36  
Auto Clock Set  
Record Length 1:30  
Description: The VCR automatically looks for time and date information after  
most power outages as well as each time the machine is turned off. Using time  
information broadcast in TV signals (if available), the VCR’s clock sets itself.  
Requirements: Start Auto Clock Set using the VCR’s on-screen menus.  
Press REC to set length  
VCR Plus+ and PlusCode are registered trademarks of the Gemstar Development Corporation.  
The VCR Plus+ system is manufactured under the license from Gemstar Development Corporation.  
COMMERCIAL ADVANCE and MOVIE ADVANCE are registered trademarks of SRT, Inc.; a Jerry Iggulden invention licensed in association with Arthur D. Little Enterprises.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Express Recording (XPR)  
TIMER RECORDINGS  
Description: XPR quickly records the remaining portion of a program already  
in progress. XPR is a great way to capture the end of a sporting event that has  
run into overtime or a live broadcast that runs long.  
1 Create a New Program  
2 Review Existing Progs.  
3 Use VCR Plus+ Code  
Requirements: Repeatedly press the Record button on the VCR front panel or  
remote control to set the desired duration of time to record.  
0 Exit  
Pro-Tect Plus™ Locking  
Description: Locks the VCR so that buttons on the front panel and remote  
control won’t operate the VCR. This feature protects timer programs from  
frustrating accidents such as being left on at the time of recording.  
Requirements: Lock the VCR by pressing and holding the POWER button on  
the remote control for six seconds. The front panel display will blink for several  
seconds. The VCR unlocks by pressing and holding the POWER button on the  
remote control, again for six seconds. The front panel display will blink again  
and release the lock on the system.  
Front Audio/Video Input Jacks  
Description: The VCR has Audio/Video (A/V) input jacks on both the front and  
rear of the unit (there are output jacks on the rear panel only). The front A/V  
jacks make it easy to plug in an external A/V device, such as a camcorder.  
Requirements: Make sure that all A/V connections are snug. To see a  
connected device’s image, turn the VCR to its Video Line Input by pressing the  
remote control’s INPUT button.  
Hi-Fi Quality Sound  
Description: When using the VCR’s A/V jacks, you can feed stereo quality  
sound from your VCR to your TV or stereo. Stereo quality sound allows for two  
separate channels of sound (Left and Right) to be heard.  
Requirements: Using A/V jacks and cables to connect the VCR to the TV or  
stereo (see page 58 for an advanced connection setup diagram).  
SQPB S-VHS Quasi Playback  
Description: Your VCR will be able to play back tapes recorded in S-VHS or  
S-VHS-ET mode (in VHS quality).  
Requirements: Insert a tape recorded in S-VHS or S-VHS-ET mode and pressing  
the PLAY button on the remote control or PLAY•PAUSE on the VCR.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Product Registration............................................................................................................. i  
Introduction ............................................................................................................................ 1  
Key Features Overview ......................................................................................................... 1  
Connections & Setup ........................................................................................................... 5  
Things to Consider Before Connecting Components .......................................................... 6  
Cable Considerations ............................................................................................................ 6  
Choose Your Connection ...................................................................................................... 7  
Using the RF Coaxial Cable to Connect the VCR to a TV .............................................. 7  
TV + VCR .......................................................................................................................... 8  
TV + VCR + Satellite Receiver ......................................................................................... 9  
TV + VCR + Cable Box ................................................................................................... 10  
Set the VCRs CH 3/4 Switch ................................................................................................ 11  
Plug in the VCR.................................................................................................................... 11  
Put Batteries in the Remote Control .................................................................................. 11  
Turn on the TV and VCR...................................................................................................... 11  
Tune the TV.......................................................................................................................... 11  
Using the Remote Control to Navigate On-Screen Menus ............................................... 12  
Complete the QuickSet Guide...................................................................................... 12  
Accessing Menus ........................................................................................................... 12  
VCR Basics ............................................................................................................................ 13  
Playing a Tape ............................................................................................................... 13  
Automatic Rewind ........................................................................................................ 13  
Tape Eject ...................................................................................................................... 13  
Recording............................................................................................................................. 13  
Check the Safety Tab .................................................................................................... 13  
Using the VCR’s Menu System ....................................................................................... 15  
Using On-Screen Menus to Set Up Features ...................................................................... 16  
Language....................................................................................................................... 16  
Cable Box Setup ............................................................................................................ 16  
VCR Channels List.......................................................................................................... 17  
Auto Channel Searching ....................................................................................... 17  
Changing the Signal Type ..................................................................................... 18  
Adding or Removing Channels ............................................................................. 18  
Time and Date............................................................................................................... 19  
Auto Clock Set Feature.......................................................................................... 19  
To Turn Auto Clock Set ON .............................................................................. 19  
Setting the Time Zone ..................................................................................... 19  
Setting Daylight-Saving Time .......................................................................... 20  
Setting Time and Date Manually .......................................................................... 20  
Additional Set Up Features in the Preferences Menu....................................................... 21  
Remote VCR1/VCR2 Option .......................................................................................... 21  
Auto Play ....................................................................................................................... 21  
Auto TV/VCR.................................................................................................................. 22  
EnergySaver................................................................................................................... 22  
Front Panel Brightness (VCR Display) .......................................................................... 22  
Tape Speed .................................................................................................................... 23  
Set Auto Repeat ............................................................................................................ 23  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Using the Remote Control ............................................................................................... 25  
Remote Control Buttons ..................................................................................................... 26  
Component Buttons ..................................................................................................... 26  
VCR Function Buttons ................................................................................................... 26  
TV Function Buttons ..................................................................................................... 27  
Using the INPUT Button ........................................................................................ 28  
Operating a TV with the VCRs Remote Control ............................................................... 28  
Do You Need to Program the Remote? ....................................................................... 28  
Using the VCR’s Features.................................................................................................. 31  
Recording Features ............................................................................................................. 32  
Express Recording (XPR) ............................................................................................... 32  
Timer Recording............................................................................................................ 33  
Stopping a Timer Recording ................................................................................. 33  
Reviewing and Clearing Programs ....................................................................... 33  
VCR Plus+ SILVER System .............................................................................................. 34  
Turning ON or OFF the Auto VCR Plus+ download ............................................. 34  
Mapping VCR Plus+ Channels Manually .............................................................. 35  
Recording Broadcast Stereo TV or SAP (Second Audio Program) ...................... 38  
Copying and Editing Tapes Using Two VCRs ............................................................... 38  
Picture Search Options ........................................................................................................ 39  
Forward and Reverse Search ........................................................................................ 39  
Slow Motion .................................................................................................................. 39  
Frame Advance ............................................................................................................. 39  
Index Search .................................................................................................................. 40  
Go-To Search ................................................................................................................. 40  
Commercial Advance .......................................................................................................... 41  
Movie Advance .................................................................................................................... 43  
Pro-Tect PlusLocking Feature ......................................................................................... 44  
Tracking................................................................................................................................ 44  
Time Counter ....................................................................................................................... 44  
On-Screen Displays .............................................................................................................. 45  
Audio Set-Up Features ........................................................................................................ 46  
Tape Playback ...................................................................................................................... 46  
Other Information .............................................................................................................. 47  
Troubleshooting Tips........................................................................................................... 48  
Questions and Answers About COMMERCIAL ADVANCE................................................. 51  
Front Panel .......................................................................................................................... 52  
Display Panel ....................................................................................................................... 53  
Back Panel............................................................................................................................ 54  
Specifications ....................................................................................................................... 55  
Cleaning the VCR ................................................................................................................ 55  
RCA VCR Limited Warranty................................................................................................. 56  
Finding the TVs Video Line Input ...................................................................................... 57  
Advanced Connection ......................................................................................................... 58  
TV + VCR + Satellite Receiver ....................................................................................... 58  
Glossary ................................................................................................................................ 59  
Index .................................................................................................................................... 60  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 1  
Connections & Setup  
Chapter Overview:  
Things to Consider Before Connecting  
Choosing Your Connection  
Making Connections  
Navigating On-Screen Menus  
Completing the QuickSetGuide  
Basic Recording  
Changing Entertainment. Again.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
Things to Consider Before Connecting  
Components  
Protect Components From Power Surges  
Connect all components before plugging any power cords into the wall outlet.  
Always turn off the TV and other components before you connect or disconnect any cables.  
Position Cables to Avoid Audio Hum or Interference  
Insert all cable plugs firmly into their jacks.  
Place any Audio/Video (A/V) cables to the side(s) of the TVs back panel instead of straight  
down the back after connecting components.  
Try not to coil any twin-lead cables and keep them away from all A/V cables as much as  
possible.  
Make sure all antennas and cables are properly grounded. Refer to the Safety Tips sheet  
packed with your unit for detailed information.  
Protect Components From Overheating  
Never block ventilation slots in any component. Arrange the components so that air can  
circulate freely.  
Do not stack components.  
Allow adequate ventilation when placing components in a stand.  
Place an amplifier or satellite receiver on the top shelf of a stand so heated air rising from it  
will not flow around other components.  
Cable Considerations  
The RF coaxial cable supplied with your VCR carries both sound and picture information. This is  
the cable used in all connection diagrams illustrated in this chapter.  
If your TV has A/V input jacks, you should use A/V cables (not supplied) to connect the VCR to  
the TV. A/V cables provide better picture and sound quality than an RF coaxial cable. If you  
would like to hook up your VCR using A/V cables, refer to the Advanced Connection  
information on page 58 in the Other Information chapter of the manual.  
6
Chapter 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
Using the RF Coaxial Cable to Connect the  
VCR to a TV  
This graphic shows the RF coaxial cable supplied with your VCR. This will be  
the cable used for the basic connections represented in this chapter.  
Notes: To hear stereo sound, you will need to purchase Audio/Video (A/V)  
cables (not provided) and connect the VCR to the TV. A/V jacks and cables  
also provide a superior image and sound quality. For details about using  
this advanced setup, see the instructions on page 58.  
RF Coaxial Cable  
Using A/V jacks to connect the VCR to the TV requires tuning to the TVs  
Video Line Input to see the VCRs picture. For more information about  
finding your TVs Video Line Input, see page 57.  
If you prefer, we can provide you with the name of an Authorized Service  
Representative who will visit your home for a fee to install your electronic  
entertainment system and to instruct you in its operation. For details about  
this service, call 1-888-206-3359.  
Choose Your Connection  
There are several ways to hook up your VCR depending on the components connected. Please use  
the following chart to determine which connection is best for you and proceed to the appropriate  
page.  
Connection  
Title  
Go To  
Components  
TV + VCR  
page 8  
TV + VCR +  
Satellite Receiver  
page 9  
TV + VCR +  
Cable Box  
page 10  
Chapter 1  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
TV (back panel)  
AUDIO  
VIDEO  
L / MONO  
L
R
IN  
OUT  
CABLE/  
ANTENNA  
S-VIDEO  
VCR  
1
ANT. IN  
RF OUT  
AUDIO  
R
L
IN  
OUT  
CH.  
2
3
4
VIDEO  
From Cable  
or Antenna  
TV + VCR  
Need Some Help?  
Note: Your television back panel may not look exactly like the model  
shown here.  
If you prefer, we can  
provide you with the  
name of an Authorized  
Service Representative  
who will visit your home  
for a fee to install your  
electronic entertainment  
system and to instruct you  
in its operation. For  
1. Connect the VCR to the TV  
Connect one end of the supplied RF coaxial cable to the RF OUT jack on  
the back of the VCR and the other end to the TVs Antenna IN jack.  
2. Connect the antenna/cable feed to the VCR  
Connect the cable or antenna RF coaxial cable to the ANT. IN jack on your  
VCR.  
details about this service,  
call 1-888-206-3359.  
Note: Flip the CH 3/4 switch on the back of the VCR to the channel that is  
not used in your area. This will be the channel that the TV must be tuned  
to in order to see the VCRs picture.  
Go To Page 11  
8
Chapter 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
TV  
AUDIO  
VIDEO  
L / MONO  
L
R
IN  
OUT  
CABLE/  
ANTENNA  
S-VIDEO  
VCR  
1
ANT. IN  
AUDIO  
VCR  
R
L
RF OUT  
IN  
OUT  
CH.  
3
4
VIDEO  
SATELLITE  
RECEIVER  
2
IN FROM ANT  
OUT TO TV  
CH3  
CH4  
OUT  
R
SATELLITE  
IN  
VIDEO  
L
S-VIDEO  
3
4
From Cable  
or TV Antenna  
From  
Satellite  
TV + VCR + Satellite Receiver  
Note: Your television and/or satellite receiver back panels may not look  
exactly like the models shown here.  
Need Some Help?  
1. Connect the VCR to the TV  
If you prefer, we can  
provide you with the  
name of an Authorized  
Service Representative  
who will visit your home  
for a fee to install your  
electronic entertainment  
system and to instruct you  
in its operation. For  
Connect one end of the supplied RF coaxial cable to the RF OUT jack on  
the back of the VCR and the other end to the TVs Antenna input jack.  
2. Connect satellite receiver to the VCR  
Connect a second RF coaxial cable (not included) to the antenna output  
jack on the satellite receiver and to the ANT. IN jack on the VCR.  
3. Connect the antenna to your satellite receiver  
details about this service,  
call 1-888-206-3359.  
If necessary, connect an antenna or cable box RF coaxial cable (not  
included) to the antenna input jack on the satellite receiver.  
4. Connect the satellite feed to the satellite receiver  
Connect the satellite receivers RF coaxial cable feed (not included) to the  
satellite input jack on the satellite receiver.  
Go To Page 11  
Chapter 1  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
TV  
AUDIO  
VIDEO  
L / MONO  
L
R
IN  
OUT  
CABLE/  
ANTENNA  
S-VIDEO  
VCR  
1
R
VC  
ANT. IN  
RF OUT  
AUDIO  
R
L
IN  
OUT  
CH.  
3
4
VIDEO  
CABLE BOX  
2
IN FROM ANT  
OUT TO TV  
CH3  
CH4  
S-VIDEO  
3
From Cable  
Feed  
TV + VCR + Cable Box  
Need Some Help?  
Note: Your television and/or cable box back panels may not look exactly  
like the models shown here.  
If you prefer, we can  
provide you with the  
name of an Authorized  
Service Representative  
who will visit your home  
for a fee to install your  
electronic entertainment  
system and to instruct you  
in its operation. For  
1. Connect the VCR to the TV  
Connect one end of the supplied RF coaxial cable to the RF OUT jack on  
the back of the VCR and the other end to the TVs Antenna input jack.  
2. Connect the cable box to the VCR  
Connect one end of a second RF coaxial cable (not included) to the cable  
details about this service,  
call 1-888-206-3359.  
boxs antenna output jack and the other end to the ANT. IN jack on the VCR.  
3. Connect the cable feed to your cable box  
Connect the RF coaxial cable feed (not included) to the antenna input jack  
on the cable box.  
Go To Page 11  
10  
Chapter 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
Set the VCRs CH 3/4 Switch  
The CH 3/4 switch on back of the VCR determines what channel the TV must be tuned to see  
the VCRs image. Choose whichever channel is not used locally in your area.  
Note: If you connected components using A/V jacks and cables, the VCRs signal must be  
viewed using the TVs Video Line Input. To find the Video Line Input, refer to the manual  
that came with the TV or see How to Find Your TV’s Video Line Input on page 57 in the  
Other Information section of this manual.  
Plug in the VCR  
Your VCRs power cord has a plastic band strung through the blades. Remove the plastic band  
before plugging the cord into the power outlet. To remove the band, cut with a pair of  
scissors and pull it free of the blades. Once the plastic is removed, match the wide blade of the  
power cord to the wide slot in the AC outlet. Be sure to insert the plug completely.  
Put Batteries in the Remote Control  
1. Remove the battery compartment cover on the remote control.  
2. Insert new batteries matching the polarities (+ and ) on the batteries with  
the diagram in the battery compartment.  
3. Put the battery compartment cover back on the remote.  
Turn on the TV and VCR  
Turn on the TV and press the VCR button on the remote control to turn it on.  
Note: If you have an RCA, GE, or Proscan TV, your VCRs remote control  
may be able to operate it without being programmed. Press the TV button  
on the remote control and then the ONOFF button. If neither one turns on  
the TV, see Using the Remote Control starting on page 25 for details about  
programming the remote control to operate other brands of TVs.  
Tune the TV  
Tune the TV to the VCR viewing channel. The VCR viewing channel is channel  
3, 4, or the TVs video line input.  
If you connect your VCR using RF coaxial cable only, turn the TV to  
channel 3 or 4 (whichever was set on the CH 3/4 switch).  
If you connected the VCR using A/V jacks and cables, select the TVs video  
line input. For more information see How to Find the TV’s Video Line Input  
on page 57 in the Other Information section of this manual.  
Chapter 1  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
Using the Remote Control to  
Navigate On-Screen Menus  
The technical term is Navigation” – how you move through the on-screen menus. The theory is  
the same for all the menu screens; use the corresponding number button on the remote control  
select it.  
To choose an on-screen item, press the remote controls corresponding number button.  
Note: Selecting a menu item can take you to another menu, activate a choice, or activate a  
data entry field (such as the hour field in the Set Time menu).  
Complete the QuickSet Guide  
The menu system in your VCR allows you to customize your preferences as  
well as use all the VCRs features. To help you use the VCR as quickly as  
possible, there is an initial QuickSet Guide that walks you through several  
important setup steps at one time.  
Select a language.  
Seleccione un idioma.  
Choisissez une langue.  
1 English  
2 Español  
3 Français  
The first time you turn on the VCR, you will be able to set up available  
channels, time and date information, and more. The first menu you will see  
asks which language you prefer to have the on-screen menus appear in.  
Note: With numbered menu choices, press the corresponding number  
button on the remote control to automatically select it. In the case of the  
language menu, press 1 for English, 2 for Español (Spanish), or 3 for  
Français (French).  
The remaining menus throughout the setup will appear in the language chosen.  
Just follow the step-by-step procedures until the QuickSet Guide is complete.  
VCR MAIN MENU  
1 VCR Plus+  
2 Timer Recordings  
3 Time  
4 Channels  
5 Setup  
Accessing Menus  
The series of preferences that are set in the QuickSet Guide can also be  
handled individually using the VCRs on-screen menu system. There are other  
settings not covered in the initial setup that are also handled using the on-  
screen menus.  
6 Preferences  
7 Audio  
8 Language  
0 Exit  
For example, if you decide to run the QuickSet Guide again, you can access the  
Setup menu by pressing the remote controls MENU button. Once the Main  
Menu is displayed, press the 5 button to choose Setup. From there, you can start  
the QuickSet Guide from the beginning.  
All of the VCRs menus are  
accessed through the Main  
Menu. Press the remote  
controls MENU button to  
start.  
All on-screen menus are accessed the same way, starting in the Main Menu  
which is displayed by pressing the remote controls MENU button.  
Note: See chapter two, Using On-Screen Menus, for details about changing  
the VCRs individual settings.  
12  
Chapter 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connections & Setup  
VCR Basics  
Once your initial settings are complete, you can begin using your VCR. In order to begin, you  
must first understand some basic concepts.  
Playing a Tape  
1. Tune the TV to your VCR viewing channel (03, 04, or the video line input).  
2. Insert a tape in the VCR.  
If the Auto Play feature is set to ON, the tape automatically begins playback  
(if the safety tab on the tape is removed).  
Press FWD or REV (FORWARD or REVERSE on the remote control) to  
cue the tape at the desired starting position.  
Press PLAY (if necessary) to begin tape play.  
Press PAUSE for stop action.  
Press TRACKING up or down (TRACKING + or on the remote  
Automatic Tracking  
control) to remove any streaks from the picture, if necessary.  
The VCR has automatic tracking  
which adjusts the picture when  
playing back a tape recorded on  
another VCR. To adjust tracking  
manually, use the TRACKING -/+  
buttons on the remote control.  
Press STOP to stop playback.  
Automatic Rewind  
The VCR automatically rewinds the tape if it reaches the end of the tape during  
playback. While rewinding, you can press the ONOFF button and the VCR will  
turn off after finishing. If the tape has no safety tab, it will be ejected.  
Tape Eject  
Press the EJECT button on the VCR when stopped to eject the tape. You can  
also press and hold the remote controls STOP button for three seconds.  
Recording  
To Capture Programming with Basic Recording Methods:  
1. Set the tape speed by pressing the SPEED button on the remote control  
(see Tape Speed on page 23 for information about recording speeds).  
2. Press the RECORD button to begin recording.  
3. Press the STOP button to halt recording.  
If you just want to pause the recording for a short time (like during a  
commercial), press PAUSE instead of STOP.  
Check the Safety Tab  
No matter which recording option you use, make sure there is a tape in the  
VCR with its safety tab in place. You cannot record on a tape with its safety tab  
removed. If the safety tab is removed and you want to record, simply cover the  
hole with adhesive tape.  
Safety Tab  
Chapter 1  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This page left blank intentionally  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 2  
Using the VCRs  
Menu System  
Chapter Overview:  
Using On-Screen Menus  
Cable Box Setup  
Setting Time and Date  
Setting VCR Preferences  
Changing Entertainment. Again.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
Using On-Screen Menus to Set Up Features  
You set up many of the VCRs features by using the menu system as discussed in the previous  
chapter. Each feature that appears in the QuickSet Guide is explained in this section as well as a  
few other features you should set up to get the most out of your VCR.  
Note: Not all the VCR screens are shown in this manual when explaining how to access  
features.  
Language  
Selecting your preferred language determines how the on-screen displays will  
appear. To change the language:  
1. Press MENU to display the VCR MAIN MENU.  
2. Press the 8 button to select LANGUAGE.  
3. Select English, Spanish (Español), or French (Français).  
LANGUAGE  
Select a language.  
1 English  
2 Español  
3 Français  
Press MENU to continue  
Is Something Missing?  
These instructions will not  
show all of the step-by-step  
On-Screen Menus. Make  
sure to follow the  
instructions completely to  
get to the menus being  
discussed.  
Cable Box Setup  
This setup applies only when all channels are received through a cable box. In  
this case, the VCR will automatically enter the channel used to view cable box  
programming. Your VCR will use this channel for all future timer recordings.  
1. Press MENU to display the VCR MAIN MENU.  
2. Press 4 to display the CHANNELS menu.  
3. Press 5 to display the CABLE BOX SETUP menu.  
CHANNELS  
1 Auto Channel Search  
2 Add/Remove Channels  
3 Signal Type:  
4 VCR Plus+ Setup  
5 Cable Box Setup  
6 SAT Setup  
CABLE  
0 Exit  
16  
Chapter 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
4. Select one of the three choices. If ALL Channelsis selected, enter the  
output channel of the cable box (usually 03 or 04), or if A/V jacks connect  
the VCR to the TV, press the INPUT button on the VCRs remote control.  
CABLE BOX SETUP  
Do you use your cable  
box to receive ALL  
channels or only SOME  
channels?  
1 ALL channels  
2 Only SOME channels  
3 Cancel setup  
5. Once you complete the setup, the VCR confirms that it will now receive all  
signals on the designated channel.  
CABLE BOX SETUP  
The VCR will now  
receive all signals  
from the cable box  
on channel 04.  
Press MENU to continue  
VCR Channels List  
Your VCR may come with a list of channels preset at the factory. Even though it  
may come with such a list, you might want to add or delete certain channels.  
Note: If you use a cable box to view all channels, this step is not necessary.  
Auto Channel Searching  
Notes: Use Auto Channel Search to place all available channels in memory.  
If you ever change cable or antenna signals, you may need to run the Auto  
Channel Search feature again.  
1. Press the MENU button to display the VCR MAIN MENU.  
2. Press 4 to select CHANNELS.  
3. Press 1 to select AUTO CHANNEL SEARCH.  
4. Select one of the three options:  
AUTO CHANNEL SEARCH  
Cable TV searches for cable stations.  
What type of signal  
are you using?  
Antenna searches for local broadcast stations.  
Detect Automatically decides which input to use for you.  
1 Cable TV  
2 Antenna  
3 Detect Automatically  
>
Note: With Detect Automatically, a strong cable or antenna signal in your  
area may cause channels to be detected inaccurately. If this should happen,  
manually select the input signal for the system you have.  
0 Cancel  
The VCR begins scanning for channels available in the area (taking about  
one-to-two minutes). When scanning is complete, the VCR tunes to the  
lowest channel available. After completing Auto Channel Search, pressing  
the remote controls CHAN + or - buttons should only select active  
channels.  
Chapter 2  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
Changing the Signal Type  
This feature is useful if your cable signal goes out; it allows you to switch to a  
regular antenna for alternate television reception.  
1. Press the MENU button to display the VCR MAIN MENU.  
2. Press the 4 button to choose CHANNELS.  
3. Press 3 to choose between Signal Type: Cable and Antenna. When  
finished, press 0 to exit back to the Main Menu and 0 again to exit to  
normal viewing.  
CHANNELS  
1 Auto Channel Search  
2 Add/Remove Channels  
3 Signal Type:  
4 VCR Plus+ Setup  
5 Cable Box Setup  
6 SAT Setup  
CABLE  
0 Exit  
Adding or Removing Channels  
You might want to add or remove channels after using Auto Channel Search,  
especially if there are weak signals or channels with content you dont care for.  
1. Press the MENU button to display the VCR MAIN MENU.  
2. Press 4 to choose CHANNELS.  
3. Press 2 to choose ADD/REMOVE CHANNELS. To go to the channel you  
want to add or remove, use the remote controls CHANNEL + or buttons  
or enter a specific channel number using the number buttons.  
Once the desired channel is displayed, the on-screen menu will tell you if  
the channel is currently in the VCRs viewing list. Press the CLEAR button to  
remove a channel from the available channels list or press the INFO button  
to add it.  
ADD/REMOVE CHANNELS  
Channel 115  
is presently ADDED  
Press CLEAR to remove  
Press MENU to exit  
4. Press the MENU button to exit out of the menus.  
Note: To view active channels, use the remote controls CHANNEL + and -  
buttons. You can also access channels not available in the active channel  
list by using the remote controls number buttons to enter the specific  
channel number.  
18  
Chapter 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
Time and Date  
Your VCR gives you two ways to set the time and date; manually or by using the Auto Clock Set  
feature. Using Auto Clock Set enables the time to be updated each time the VCR is turned off by  
using time and date information carried in certain broadcast signals.  
Auto Clock Set Feature  
The Auto Clock Set feature is set to ON by default at the factory. In the ON setting, the VCR  
looks for a channel carrying time data and updates the clock automatically. In order for Auto  
Clock Set to work properly though, certain steps must first be completed such as Auto Channel  
Search, setting the time zone, and setting the Daylight-Saving feature.  
Notes: Auto Clock Set is available only in limited areas.  
You must set available channels, time zone, and Daylight-Saving settings for Auto Clock Set  
to work.  
When using Auto Clock Set with a cable box, the VCR will not reset the clock after a power  
outage unless the cable box is tuned to the channel carrying time data.  
If the time does not automatically set after trying for ten minutes, manually set the time  
and date information using the TIME menu (see the next page for information on manually  
setting time and date information).  
To Turn Auto Clock Set ON  
Note: make sure that available channels, time zone, and Daylight-Saving  
features are set before turning on Auto Clock Set.  
1. Press MENU to display the VCR MAIN MENU.  
2. Press 3 to choose TIME.  
3. Press the 2 button repeatedly to toggle between Auto Clock Set ON and OFF.  
TIME  
1 Set Time and Date  
2 Auto Clock Set:  
3 Set Time Zone  
ON  
4 Set Daylight Saving  
Time Data was found  
on channel 20.  
0 Exit  
Setting the Time Zone  
1. Press MENU to display the VCR MAIN MENU.  
2. Press 3 to choose TIME.  
3. Press 3 to chose SET TIME ZONE.  
SET TIME ZONE  
What is your Time Zone?  
1 Eastern  
2 Central  
3 Mountain  
4. Select your time zone by pressing the corresponding number button.  
If you select Automatic for your time zone, the VCR sets the clock using the  
first time information it finds. If the time set is not correct, select another  
time zone or set the time and date through the menu system.  
4 Pacific  
5 Alaska  
6 Hawaii  
7>Automatic  
Press MENU to continue  
Chapter 2  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
Setting Daylight-Saving Time  
1. Press MENU to display the VCR MAIN MENU.  
2. Press 3 to choose TIME.  
3. Press 4 to choose SET DAYLIGHT SAVING.  
TIME  
1 Set Time and Date  
2 Auto Clock Set:  
3 Set Time Zone  
ON  
4 Set Daylight Saving  
Time Data was found  
on channel 20.  
0 Exit  
4. Select the appropriate option.  
SET DAYLIGHT SAVING  
Notes: DST stands for DaylightSaving Time.  
Does your area observe  
Daylight Saving Time  
from April to October?  
If you choose Automatic for the time zone, the VCR sets the clock using any  
DST information broadcast in the channels signal.  
1 Yes, DST is observed  
2 No  
3 Automatic  
Press MENU to continue  
Displaying Time and Date  
Setting Time and Date Manually  
If Auto Clock Set was unsuccessful, set the time and date manually in the TIME  
menu. Auto Clock Set is automatically turned off when time and date  
information is set this way.  
Pressing the INFO button on  
the remote control or VCR  
displays the time and date on  
screen temporarily.  
1. Press MENU to display the VCR MAIN MENU.  
2. Press 3 to choose TIME.  
TIME  
3. Press 1 to choose SET TIME AND DATE.  
1 Set Time and Date  
2 Auto Clock Set:  
3 Set Time Zone  
ON  
4 Set Daylight Saving  
Time Data was found  
on channel 20.  
0 Exit  
4. Enter the data using the number buttons. Press 0 before single-digit  
numbers and follow the on-screen directions to exit the menus.  
SET TIME AND DATE  
Time --:--  
(hh:mm)  
Date --/--/--  
Press MENU to cancel  
20  
Chapter 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
Additional Set Up Features in the  
PREFERENCES  
1 Remote Control: VCR1  
2 Auto Play:  
3 Auto TV/VCR:  
4 EnergySaver:  
5 Front Panel:  
6 Tape Speed:  
7 Set Auto Repeat  
ON  
ON  
2:00  
AUTO  
SLP  
Preferences Menu  
Note: The features described on the following pages are all accessed  
through the PREFERENCES menu.  
To Access the PREFERENCES menu:  
8 COMMERCIAL ADVANCE  
0 Exit  
1. Press MENU to display the VCR MAIN MENU.  
2. Press 6 to select PREFERENCES.  
The PREFERENCES menu  
allows changes to be made  
to a variety of different  
VCR features.  
You are now ready to select an item from the PREFERENCES menu to set up.  
Remote VCR1/VCR2 Option  
Some universal remote controls have buttons labeled VCR1 and VCR2. These  
remotes can operate up to two VCRs. If you have a universal remote control with  
this ability, your RCA VCR can be controlled with either the VCR1 or VCR2 button.  
See the documentation that came with your universal remote control for details  
about programming it to operate your RCA VCR.  
In the PREFERENCES menu, press 1 to select the Remote Control feature. Then  
press the VCR2 button on your universal remote control to change the setting.  
Then, the VCR will respond to the universal remote controls VCR2 button. To  
change the remote control setting back to VCR1, display the PREFERENCES menu,  
press 1, and then press the VCR1 button on the universal remote control.  
Note: Remember you must press VCR1 or VCR2 on a universal remote  
control (not included) whichever is selected in the PREFERENCES menu—  
before the remote control will operate the VCR.  
Auto Play  
With Auto Play turned ON (the factory default setting), the VCR automatically  
starts playback when you insert a tape with its safety tab removed.  
To Access Auto Play:  
1. In the PREFERENCES menu, press 2 repeatedly to switch between Auto  
Play: ON and OFF.  
Select ON if you want a tape with its safety tab removed to start playing  
automatically when inserted.  
Select OFF if you do not want a tape with its safety tab removed to start  
playing automatically.  
Chapter 2  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
Auto TV/VCR  
PREFERENCES  
1 Remote Control: VCR1  
2 Auto Play:  
ON  
ON  
2:00  
AUTO  
SLP  
To control whether the VCRs TV/VCR setting changes automatically to VCR-  
viewing mode when turned on, use the Auto TV/VCR setting.  
3 Auto TV/VCR:  
4 EnergySaver:  
5 Front Panel:  
6 Tape Speed:  
7 Set Auto Repeat  
To Access Auto TV/VCR:  
In the PREFERENCES menu, press 3 repeatedly to toggle between Auto TV/VCR:  
ON and OFF.  
8 COMMERCIAL ADVANCE  
0 Exit  
The PREFERENCES menu  
allows changes to be made  
to a variety of different VCR  
features.  
Note: Pressing the TVVCR button on the remote control will switch  
between VCR and TV-viewing modes. When in VCR-viewing mode, VCR is  
displayed on the front panel. The VCR indicator turns off when in TV-  
viewing mode.  
Select ON to switch VCR-viewing mode on automatically when the power is  
turned on. The VCR must be connected to the TV using the supplied RF  
coaxial cable.  
Select OFF to remain in the TV-viewing mode when the VCR is initially  
turned on. Leaving Auto TV/VCR off is useful if you use A/V cables to  
connect the VCR to the TV and you watch the VCRs picture using the TVs  
Video Line Input. This way, the antenna/cable signal will not be interrupted  
by the VCR.  
EnergySaver  
By default, the VCR automatically turns off after two hours of inactivity. This can  
be changed in the PREFERENCES menu by pressing the 4 button repeatedly to  
change the time delay or to disable the feature altogether.  
Select OFF and the VCR will stay on until you shut it off.  
Select 1:00, 2:00, or 3:00 and the VCR will turn off after one, two, or three  
hours of inactivity.  
Thirty seconds before automatically shutting off, the VCR displays an on-screen  
message reading, The VCR will turn off in 30 seconds. Press any key to cancel.  
Pressing any remote control or VCR front panel button will halt the countdown.  
If you use the VCRs tuner instead of your TV to view channels, you may want  
to turn off this feature.  
Front Panel Brightness (VCR Display)  
You can change the brightness level of the VCRs front panel display. In the  
PREFERENCES menu, press the 5 button repeatedly to toggle between options:  
AUTO means the display brightens when the VCR is on and dims when the  
VCR is off.  
BRIGHT keeps the display bright whether the VCR is on or off.  
DIM keeps the display at a low brightness level whether the VCR is on or  
off.  
22  
Chapter 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using On-Screen Menus  
Recording Speeds  
Tape Speed  
SP (Standard Play)  
You can choose as the preferred recording tape speed either Standard Play (SP)  
or Super Long Play (SLP). The speed selected appears in the VCRs front display  
panel and in timer and VCR Plus+ system recording menus.  
Gives the best quality recording,  
but fewer programs can be  
recorded on the tape.  
SLP (Super Long Play)  
Gives three times the recording  
time of tapes recorded in SP  
mode.  
To Select a Preferred Tape Speed:  
In the PREFERENCES menu, press the 6 button repeatedly to switch between  
SP and SLP settings.  
Note: For an explanation of recording speeds, see the note to the left.  
Recording Times  
Cassette  
T-120  
SP  
SLP  
To Override the Preferred Tape Speed:  
2 Hr  
6 Hr  
Press the SPEED button on the remote control.  
T-160  
2 Hr/40 Min 8 Hr  
Set the tape speed in the timer or VCR Plus+ system recording menus.  
When you turn off the VCR, the tape speed reverts to the one selected as the  
default.  
Set Auto Repeat  
A tape can be set to play the same segment over and over in a repeating loop  
with the Set Auto Repeat feature. Set Auto Repeat uses the VCRs memory  
counter to determine the duration of the loop.  
In the PREFERENCES menu, press the 7 button to choose Set Auto Repeat. The  
SET AUTO REPEAT menu will ask for an ending time for the loop to be  
specified:  
AUTO REPEAT  
Set the length of time  
you want the tape to  
play in a repeating loop  
The CLEAR button will erase all three numbers entered and move the cursor  
back to the first position (hours).  
Loop from 0:00 to 2:--  
(h:mm)  
Press CLEAR to turn off  
Press MENU to exit  
The Press CLEAR to turn off message will appear only after the first number  
has been entered into the end time.  
Auto Repeat is set back to -:-- by resetting the dialog box, ejecting a tape,  
powering off the VCR, power interruption, or by recording start.  
When a duration time has been set:  
The VCR will automatically switch to rewind if the counter meets or goes  
past the set Auto Repeat duration.  
The VCR will automatically switch to playback during rewind if the counter  
equals or is less than 0:00.  
The Auto Repeat may be adjusted by setting the counter to 00:00. This can  
be done by pressing the CLEAR button while the tape counter is on screen  
or on the front panel display.  
The counter will not reset while rewinding in an Auto Repeat loop.  
Chapter 2  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This page left blank intentionally  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 3  
Using the  
Remote Control  
Chapter Overview:  
Buttons on the Remote Control  
Programming the Remote to Operate Other Components  
How To Use the Remote After Youve Programmed It  
Changing Entertainment. Again.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
Remote Control Buttons  
The backlit remote has a light button ( ) that glows in the dark. Press  
this button to light the buttons on the remote. The remote buttons  
remain lit when they are pressed within a few seconds of each other. If  
a button is not pressed within approximately seven seconds, the light  
turns off to conserve battery power.  
The remote control is capable of controlling your VCR and many  
brands of televisions. If you have an RCA, GE, or Proscan TV, you may  
be able to control it without having to program the remote.  
ONOFF  
TV  
VCR  
REVERSE  
PLAY  
FORWARD  
Component Buttons  
RECORD  
INFO  
STOP  
PAUSE  
ONOFF Turns off VCR when remote is set to control the VCR. Also  
turns some compatible components on and off.  
SEARCH  
TV Turns on a compatible RCA, GE, or PROSCAN TV and sets the  
remote to control the TV. Also used with the ONOFF button to turn  
on a different brand of TV (if programmed) and sets the remote to  
control the TV.  
MUTE  
GO BACK  
SPEED  
VCR Turns on a compatible RCA, GE, or PROSCAN VCR and sets the  
remote to control the VCR.  
CLEAR  
MENU  
1
3
2
5
8
0
VCR Function Buttons  
6
4
7
CHAN Up or Down Selects next higher or lower channel in the VCRs  
channel memory.  
9
CLEAR Resets time counter to 0:00:00. Allows you to change entries  
when setting the clock or a timer recording.  
F. ADV Lets you view one frame with each press of the button when  
tape is in pause.  
TRACKING  
F.ADV  
FORWARD Fast forwards the tape when the VCR is stopped. Searches  
forward through a tape during playback. Starts slow motion during  
play-pause and increases slow-motion speed.  
GO BACK Switches between two channels. Select one channel and  
then select another using the number buttons. Press GO BACK to  
switch between the two channels. In menu mode, press to go back to a  
previous menu.  
INFO Shows the status displays on the TV screen.  
INPUT Selects between the VCRs line input or tuner. Line input refers  
to the signal coming from the component connected to the AUDIO/  
VIDEO IN jacks on the back (L1) or front (L2) of the VCR.  
MENU Brings up VCR MAIN MENU on the TV screen.  
Numbers (0 through 9) Select a channel up to 99 by pressing two  
numbers. Select a cable channel over 99 by pressing and holding 1  
until 1 – – appears on the screen. Then press the other two numbers.  
26  
Chapter 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
PAUSE Pauses playback or recording. Press PAUSE a second time to return to  
playback or recording.  
PLAY Plays a tape.  
RECORD Starts VCR recording. Also used for Express recording.  
REVERSE Rewinds the tape when the VCR is stopped. Searches backward through a  
tape during playback. Starts slow motion during play-pause and decreases slow-  
motion speed.  
SEARCH Displays INDEX and GO-TO Search menus on screen when the VCR is  
stopped. Advances the tape forward through 30 seconds of recorded material during  
playback. Each press advances the tape an additional 30 seconds (up to five minutes).  
This button also displays the MOVIE ADVANCE screen for prerecorded movies and  
starts COMMERCIAL ADVANCE skipping during playback.  
SPEED Selects a recording speed (SP or SLP).  
STOP Stops the current VCR function such as record, playback, rewind, or fast  
forward.  
TRACKING Up or Down Lets you manually reduce the streaks that may appear on  
the picture during play, slow motion, or pause. Reduces picture jitterduring stop-  
action playback.  
TVVCR Switches the picture signal so that it either comes from the VCR or cable/  
antenna system.  
TV Function Buttons  
CHAN Up or Down Selects next higher or lower channel in the TVs channel  
memory.  
CLEAR Removes menus or status displays from the screen.  
GO BACK Switches between two channels. Select one channel and then select  
another using the number buttons. Press GO BACK to switch between the two  
channels.  
INFO Shows the TVs status displays on the TV screen.  
INPUT Selects between the TVs input channel or tuner. Press to see the VCR signal if  
you connected your VCR using the  
AUDIO/VIDEO jacks.  
MUTE Reduces volume to minimum level.  
Numbers (0 through 9) Select a channel up to 99 by pressing two numbers. Select  
a cable channel over 99 by pressing and holding 1 until 1 – – appears on the screen.  
Then press the other two numbers.  
ONOFF Turns a compatible TV off and on.  
VOL Up and Down Raises and lowers sound of TV.  
Chapter 3  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
Using the INPUT Button  
Use the INPUT button to toggle through the available Video Line Input sources (L1, L2, and  
regular broadcasting signals) and regular broadcast signals. Video Line Input allows you to view  
the image from a connected device (like a camcorder) through the VCR.  
1. Press the remote controls VCR button to activate VCR-controlling mode. Make sure that the  
VCR is turned ON.  
2. Press the remote controls INPUT button to tune to the Video Line Input source. L1  
represents the rear A/V jacks and L2 represents the front A/V jacks.  
3. Press the INPUT button again to tune back to the broadcast signal you were previously  
watching through the VCR.  
Operating a TV with the VCRs Remote Control  
The remote control that came with your VCR can be programmed to operate most brands of  
remote-controllable TVs and should already control most RCA, GE, and Proscan models without  
programming.  
Do You Need to Program the Remote?  
To determine whether the remote control needs to be programmed to operate your TV, turn the  
TV on, point the remote control at it, then press the remote controls TV button (this puts the  
remote control into TV-operating mode and should automatically turn on most RCA, GE, and  
Proscan TVs). Press the remote controls ONOFF button to see if the TV responds to the  
command. If not, the remote control needs to be programmed to control that model TV.  
Programming the Remote Control  
To program your remote control, you must use the code list on the next page. Look up the  
brand name of your TV and the code(s) that brand uses.  
Notes: This remote control may not operate all models of the brands shown in the code list.  
Note the difference between the TV and VCR on-screen displays to know which component  
the remote control is operating.  
1. Turn on the TV.  
2. Find your TV brand and code number(s) in the code list.  
3. Press and hold the TV button on the remote control.  
4. Enter the code from the code list.  
5. Release the TV button, then press the CHAN up or down button. If the TV responds to the  
remote controls command, the remote is programmed.  
6. If the TV does not respond, repeat these steps using the next code listed for your TVs  
brand.  
28  
Chapter 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
TV Codes  
Akai ...................................... 03  
NAD ......................................... 07  
NEC ......................................... 06  
Panasonic ..................... 04, 08, 11  
Philco ........................... 04, 06, 12  
Philips ..................... 03, 04, 06, 12  
Pioneer .................................... 06  
Portland ............................. 06, 12  
Proscan .................................... 01  
Proton ...................................... 06  
Quasar ..................................... 11  
Radio Shack ................. 01, 05, 13  
RCA .............................. 01, 06, 12  
Realistic .................................... 05  
Sampo ...................................... 06  
Samsung ...................... 06, 09, 12  
Sanyo ................................. 05, 08  
Sears ...... 01, 05, 06, 07, 08, 10, 12  
Sharp .................................. 06,13  
Sony ......................................... 03  
Soundesign .............................. 06  
Sylvania ....................... 04, 06, 12  
Technics ................................... 11  
Techwood ................................ 06  
Teknika .................................... 06  
TMK ......................................... 06  
Toshiba ................... 05, 07, 08, 09  
Universal .................................. 00  
Victor ....................................... 10  
Wards .......... 00, 01, 04, 06, 12, 13  
Yamaha .................................... 12  
Zenith ...................................... 02  
AOC ................................... 06,12  
Candle ................................... 06  
Citizen .................................... 06  
Colortyme .............................. 06  
Concerto ................................ 06  
Curtis Mathes ..................... 01,06  
Daewoo ............................. 06,12  
Daytron .................................. 06  
Electrohome ....................... 06,12  
Emerson ................................. 06  
Envision ............................ 05, 06  
Fisher ................................ 05, 08  
GE ........................ 00, 01, 06, 11  
Goldstar ............................. 06,12  
Hallmark ................................ 06  
Hitachi ............................... 06,14  
Infinity ................................... 04  
J C Penney ....... 00, 01, 06, 09, 12  
JBL ......................................... 04  
Jensen .................................... 06  
JVC ................................... 10, 11  
Kawasho ........................... 03, 06  
Kenwood .......................... 06, 12  
Loewe .................................... 04  
Luxman .................................. 06  
LXI .............................. 04, 05, 07  
Magnavox ................... 04, 06, 12  
Marantz ............................. 04, 06  
MGA ................................. 06, 12  
Mitsubishi .......................... 06, 12  
MTC ....................................... 06  
Chapter 3  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Remote Control  
Operating the TV  
After you set up the remote control, see which buttons operate your TV:  
1. Point the remote control at the TV, and press the TV button. If the TV does not turn on,  
press the TV button and then press the ON OFF button.  
2. You may want to experiment to see which buttons operate your TV. Try pressing buttons,  
such as VOL and MUTE. See the button descriptions in this chapter for details about what  
each remote control button does.  
30  
Chapter 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 4  
Using the VCRs Features  
Chapter Overview:  
Recording  
Express Recording (XPR)  
Timer Recordings  
Using the VCR Plus+ System  
Copying and Editing Tapes  
Changing Entertainment. Again.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Recording Features  
Your VCR provides many ways to capture programming:  
1. Recording lets you press one button to record a program.  
2. Express Recording (XPR) allows recording to start while a program is being watched.  
This feature automatically stops recording after a designated period of time.  
3. Timer Recording program the VCR for a daily, weekly, or one-time recording which will  
automatically start and stop at the times you set.  
4. Timer Recording with the VCR Plus+ System program the VCR by entering a PlusCode  
programming number found in most TV program listings.  
Express Recording (XPR)  
Use XPR to quickly record the remaining portion of a program being watched. XPR is a great  
way to capture the end of a sporting event that has run into overtime or a live broadcast that  
runs long.  
XPR works in 30-minute increments. You can capture the last 30, 60, 90, etc. minutes of  
programming (depending on tape length), up to four hours total.  
To Activate XPR:  
Rec  
Ch 36  
Record Length 0:00  
1. If necessary, turn on the VCR and tune it to the channel with the desired  
programming.  
2. If necessary, insert a tape with its safety tab in place into the VCR. Make  
sure it is cued to record at the proper starting point.  
Rec  
Ch 36  
Record Length 1:30  
Note: To override the preferred tape speed setting, press the SPEED button  
on the remote control repeatedly to toggle between SP and SLP choices.  
Pr
3. Press the RECORD button on the remote control or VCR front panel to start  
recording.  
Press REC to set length  
4. Repeatedly press the RECORD button to set up the recording duration.  
Each press of the RECORD button adds 30 minutes of recording time.  
The VCR automatically turns off after recording for the set time.  
To stop an XPR recording, press and hold the STOP button on the  
remote control or VCR front panel for several seconds until STOP  
appears on the VCR on-screen display.  
32  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Timer Recording  
You can program up to eight different broadcasts to be recorded.  
NotesIn order for a timer recording to work:  
The VCRs clock must be set correctly.  
Insert a tape with its safety tab in place and enough tape to record  
the program.  
TIMER RECORDINGS  
If youve set up the VCR for a cable box for all channels, the output of  
your cable box appears in the channel item of the Timer Recording  
menu.  
1 Create a New Program  
2 Review Existing Progs.  
3 Use VCR Plus+ Code  
PROGRAMS OVERLAP appears if two programs whose times overlap  
are entered.  
TIMER appears in the display when you turn off the VCR and a timer  
recording has been set. TIMER flashes if there is no tape in the VCR  
when a timer recording has been set and the unit is turned off.  
How often should this  
0
program record?  
1 One time  
For a cable box or satellite receiver, turn it on and tune it to the  
channel you want to record before the recording is to begin.  
2 Daily (every day)  
3 Weekdays (M-F)  
4 Weekly (once per week)  
To Set Up to as Many as Eight Timer Recording Programs:  
1. Press the MENU button to display the VCR MAIN MENU.  
2. Press the 2 button to choose TIMER RECORDINGS.  
3. Press the 1 button to choose Create a New Program.  
4. Select how often you want the program to record.  
5. Enter the data for the program with the number buttons.  
Program 1 has been saved  
0
Remember to insert a  
recordable tape and  
turn the VCR off before  
the program start time.  
Press MENU to continue  
The data includes the channel number (press INPUT to select the Video Line  
Input if using A/V jacks to connect the VCR to the TV), and start and end  
times (including AM or PM). The start date is automatically entered based on  
the VCR clock. Both the recording date and speed can be changed.  
6. Review the information to make sure it is correct.  
7. Press the MENU button to save.  
Stopping a Timer Recording  
To stop or cancel a timer recording in progress (even an Express Recording):  
Press and hold the STOP button for several seconds until STOP appears in the  
on-screen display.  
Program 1 (One time)  
Reviewing and Clearing Programs  
To review programs that you have already set up:  
Channel  
Start Time 12:00 AM  
End Time 01:30 AM  
104 Cable  
1. Press the MENU button to display the VCR Main Menu.  
2. Press the 2 button to choose TIMER RECORDINGS.  
3. Press the 2 button to choose Review Existing Progs.  
Start Date 11/16/01 Fri  
Tape Speed SLP  
Press CLEAR to erase  
Press MENU for next prog  
4. Press CLEAR to erase or MENU to see the next saved timer recording  
program.  
Chapter 4  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
VCR Plus+ SILVER System  
The VCR Plus+ SILVER system makes VCR set up easier by setting and updating the clock and  
channel list for you automatically. During the first-time QuickSet Guide setup, the VCR prompts  
you to enter your zip code. Soon after, the VCR clock will set itself and your VCR Plus+ system  
channel list will be input for you.  
Time, date, and VCR Plus+ system information are downloaded from participating TV stations  
over your antenna or cable system. Time and date information are updated each time the VCR is  
turned off (and after every power interruption). So, when your TV stations or cable company  
update their lineups, your VCR will get the most current channel list automatically, freeing you  
from having to manually change the channel list yourself.  
If your VCR Plus+ SILVER system fails to download the proper information for any reason, you  
can always manually map the channels. You can also turn off AUTO VCR Plus+ if you keep  
getting prompts about multiple cable services by pressing the 2 button in the VCR Plus+ SETUP  
menu.  
Turning ON or OFF the  
VCR PLUS+ SETUP  
Auto VCR Plus+ download  
If the automatic VCR Plus+ download continuously fails for any reason, you will  
Last automatic setup  
was unsuccessful.  
Would you like to:  
see the prompt to the left.  
1 Try again  
2 Finish setup manually  
3 Cancel the auto setup  
If you decide to turn off Auto VCR Plus+ all together, you can do this by:  
1. Press the MENU button on the remote control to access the VCRs MAIN  
MENU  
2. Press 4 to access the CHANNELS menu.  
3. Press 4 to access the VCR Plus+ Setup menu.  
4. Pressing 1 will take you to a screen to manually map VCR Plus+ channels.  
VCR PLUS+ SETUP  
Pressing 2 will toggle between Auto VCR Plus+: ON or OFF.  
1 Set channel lists  
2 Auto VCR Plus+:  
ON  
Make sure this feature is turned off if you continually get fail to download  
prompts and map the channels manually.  
VCR Plus+ data was not  
found.  
0 Exit  
VCR Plus+ and PlusCode are registered trademarks of the Gemstar Development Corporation.  
The VCR Plus+ system is manufactured under the license from Gemstar Development Corporation.  
34  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Mapping VCR Plus+ Channels Manually  
Using the VCR Plus+ SILVER system can make taping timer recordings for cable or off-air antenna  
easier. If your VCR Plus+ SILVER system setup failed during the QuickSet, then you will need to map  
the channels for your local service manually. A worksheet and abbreviated codes for typical cable  
services in the U.S. and Canada are provided.  
1. Press the MENU button to display the VCR MAIN MENU.  
2. Press the 4 button to choose CHANNELS.  
3. Press the 4 button to choose VCR Plus+ Setup.  
4. Press 1 to display the Set Channel Lists menu.  
VCR PLUS+ SETUP  
1 Set channel lists  
2 Auto VCR Plus+:  
ON  
VCR Plus+ data was not  
found.  
0 Exit  
5. Enter the data following the on-screen directions using  
your worksheet.  
VCR+ Channel My Channel  
5
4
--  
--  
3 -> -> -> --  
2
1
--  
--  
Use CH+/- to select  
Press 0-9 to change  
Press MENU to save  
VCR+ Channel My Channel  
5
4
46  
--  
3 -> -> -> 23  
2
1
--  
--  
Use CH+/- to select  
Press 0-9 to change  
Press MENU to save  
(Screen shown is for an example only.)  
Chapter 4  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Two-Digit VCR Plus+ System  
Two-Digit VCR Plus+ System  
Channel Numbers for  
Channel Numbers for  
Cable TV (USA List)  
Cable TV (Canadian List)  
35 ................... American Movie Classics  
39 ........................ Arts &-Entertainment  
57 ......................... Black Entertainment  
54 .................................................. Bravo  
42 ......................... Cable News Network  
45 ............................................. Cinemax  
98 .......................................... Cinemax 2  
37 .....................The Discovery Channel  
53 ..........................The Disney Channel  
63 ..................Entertainment Television  
34 ........................ESPN Sports Network  
47 ..........................The Family Channel  
33 .............................. Home Box Office  
95 ........................... Home Box Office 2  
96 ........................... Home Box Office 3  
51 ..................... The Learning Channel  
46 ..............................................Lifetime  
58 ...........................The Movie Channel  
48 ................................ Music Television  
49 ......................The Nashville Network  
38 ...................................... Nickelodeon  
64 ...........................Nostalgia Television  
99 ........................... Quality Value Cable  
41 ........................................... Showtime  
97 ........................................ Showtime 2  
59 .................................. Sports Channel  
52 ............... Turner Network Television  
44 ..................................... USA-Network  
62 ....................................... Video Hits 1  
93 .............................. Viewer’s Choice 1  
94 .............................. Viewer’s Choice 2  
55 .................................... WGN Chicago  
43 .................................... WTBS Atlanta  
60 .............................. WWOR-New York  
67 .................. Allarcom Pay Television/  
Superchannel  
44 ........................ Arts & Entertainment  
72 ........................ Cable News Network-  
Headline News  
61 ......................... Cable News Network  
70 ............... Canadian Home Shopping  
Network  
56 ..................................... Canal Famille  
69 ......................... Cathay International  
Television Inc.  
68 ................. Chinavision Canada Corp  
60 ..................Country Music Television  
63 ................................. Family Channel  
62 ........................................First Choice  
96 ................................ First Choice Two  
97 ............................ First Choice Three  
99 ...............................First Choice Four  
90 .......................... House of Commons  
91 .......................... La Chaine Francaise  
51 ..................... The Learning Channel  
65 ............... MeteoMedia/The Weather  
Network  
48 ......................... MuchMusic Network  
55 .......................................MusiquePlus  
52 ............................. Nashville Network  
73 ................................ Newsworld/CBC  
53 .........................Le Reseau des Sports  
43 .......................... The Sports Network  
64 ....................................... Super Ecran  
37 ....................................Super Ecran B  
98 ................................... Super Ecran C  
66 ............................... Telatino Network  
46 .................................... TV5 Montreal  
92 .............................. Viewer’s Choice 1  
93 .............................. Viewer’s Choice 2  
94 .............................. Viewer’s Choice 3  
95 .............................. Viewer’s Choice 4  
71 .......................... Vision TV: Canada’s  
Faith Network  
38 ...................... Youth TV, Canada Inc.  
Note: Refer to your local TV program listings for a complete VCR Plus+ channel list for your  
viewing area or contact your cable company. Using the list may save you some time.  
36  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
VCR Plus+ System Worksheet  
Broadcast or  
Cable-TV  
Station Name  
Channel Number  
You Receive the  
Station On*  
VCR Plus+ System  
Channel Number**  
HBO  
33  
34  
ESPN  
*Check your local or cable listings for the channel number you receive this station on.  
**Check your local listings for broadcast or VCR Plus+ channel number assigned.  
Chapter 4  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Recording Broadcast Stereo TV or SAP  
(Second Audio Program)  
Some TV programs are broadcast with stereo audio or SAP (Second Audio Program).  
1. Turn on the TV and tune it to the VCR viewing channel (either 03, 04, or the TVs Video  
Line Input).  
2. Insert a tape with its safety tab in place.  
3. If your VCR viewing channel is 3 or 4, make sure the VCR indicator appears in the front  
display. If not, press the TVVCR button on the remote control to turn it on.  
4. Press the SPEED button on the remote control if you want to override the preferred Tape  
Speed setting. The tape speed indicator appears on the TV screen.  
5. Select the channel or Video Line Input to be recorded.  
6. Set the Reception: STEREO/MONO/SAP feature for the type of audio you want to record.  
7. Press RECORD to start recording.  
8. Press STOP when finished.  
Copying and Editing Tapes Using Two VCRs  
Use one VCR as the playback VCR and the other as the recording VCR.  
CABLE BOX or ANTENNA  
IN  
OUT  
1. Turn on the TV and VCRs.  
2. Tune the TV to the VCR viewing channel (either 03, 04, or the TVs Video  
PLAYBACK  
VCR  
Line Input).  
3. If you connected your VCR using the ANT. IN and RF OUT jacks, tune the  
recording VCR to channel 3 or 4whichever is selected on the back of the  
playback VCR.  
AUDIO  
OUT IN  
ANT. IN  
RF OUT  
R
L
CH  
3
4
If you have connected your VCR using the A/V jacks, press INPUT on the  
recording VCRs remote control to select the Video Line Input. Select L1 for  
the jacks on the back of the VCR or L2 for the jacks on the front.  
VIDEO  
RECORDING  
VCR  
4. Insert the tape you want to copy into the playback VCR. Insert a tape with  
its safety tab in place into the recording VCR.  
AUDIO  
ANT. IN  
RF OUT  
OUT  
IN  
5. Press PLAY on the playback VCR to begin playback. When you reach the  
point on the tape or program where you want to begin copying, press the  
PAUSE button. You may need to adjust the tracking.  
R
L
CH  
3
4
VIDEO  
6. Press the RECORD button, then press PAUSE on the recording VCR.  
TO TV  
7. Press the PAUSE buttons on both VCRs at the same time to begin copying  
the tape.  
8. To edit segments that you do not want to copy:  
Caution:  
The unauthorized recording of  
satellite broadcasts, television  
programs, or other copyrighted  
materials may infringe the rights  
of others.  
Press PAUSE on recording VCR to pause copying.  
Locate the next segment you want to copy on the playback VCR by  
using FWD, REV, and PLAY, and then press PAUSE.  
Press PAUSE on both VCRs at the same time to resume copying.  
9. Press STOP on both VCRs when finished.  
38  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Picture Search Options  
The basic way to search during playback is using the remote controls FORWARD or REVERSE  
buttons (FWD and REV on the VCR). This section contains several other options available for  
searching a tape.  
Insert Tape:  
Forward and Reverse Search  
You can search a tape during playback either forward or reverse in direction.  
Dont forget to insert a recorded  
tape when using the search  
features.  
Note: Sound is turned off during picture search.  
1. Press the FORWARD button to search forward or the REVERSE button to  
search backwards.  
2. Press the FORWARD , REVERSE, or PLAY button to return to normal  
playback.  
Slow Motion  
You can view a tape during play or play-pause mode using Slow Motion search.  
1. In pause mode, press the FORWARD (FWD) or REVERSE (REV) button to  
start slow-motion playback.  
2. Press the FORWARD button to increase or the REVERSE button to decrease  
the search speed.  
3. Use the TRACKING + or buttons to remove any streaks from the picture.  
4. Press the PLAY button to return to normal playback.  
The VCR switches automatically from slow-motion playback to stop after a  
few uninterrupted minutes.  
Frame Advance  
Frame Advance lets you view single-frame action during playback.  
1. While playback is in progress, press the remote controls PAUSE button  
(PLAY/PAUSE on the VCR) to freeze the action.  
2. Press the F. ADV button on the remote control each time you want to view  
the next frame of the recording.  
3. Press the PAUSE or PLAY button on the remote control (PLAY/PAUSE on the  
VCR) to return to normal playback.  
Chapter 4  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Index Search  
The VCR has a VHS Index Search Systemthat automatically records index marks on the tape  
every time you start a recording. During playback you can locate the program you want to play  
by the number of index marks or by scanning. The VCR will search forward or reverse from the  
location you are at on the tape.  
To Activate Index Search:  
1. While playing back, press the STOP button to freeze the action.  
2. Press the SEARCH button on the remote control to display the INDEX  
INDEX SEARCH  
SEARCH screen on the TV screen.  
Press REV or FWD  
to begin scanning  
OR  
enter a specific  
index number  
--  
Press SEARCH to exit  
3. If you want to search through a certain number of index marks, press two  
number buttons to enter the number of marks you want to search. Press the  
CLEAR button on the remote control to correct an entry.  
4. Press the FORWARD button to search forward or the REVERSE button to  
search in reverse. The VCR will locate your index mark and begin playback.  
If you did not enter a specific index number, the VCR will locate the next  
index mark and begin playback.  
5. Press STOP to stop Index Search.  
NotesCertain index marks may be missed by the VCR including:  
Marks too close to the current location of the tape.  
Those at the beginning of a recording lasting five minutes or less.  
Index marks that start at the beginning of the tape.  
GO-TO SEARCH  
Go-To Search  
The Go-To Search feature enables the VCR to quickly locate a counter reading  
anywhere on the tape. When the VCR locates the counter reading, it will begin  
playback.  
Current tape counter is  
2:17:25  
Press REV or FWD  
to go to -:--:00  
1. Press the STOP button.  
Press SEARCH to exit  
2. Repeatedly press the SEARCH button on the remote control until the  
GO-TO SEARCH menu appears on the screen.  
3. Use the number buttons to enter the hour and/or minute of the counter  
reading you want the VCR to go to. If necessary, press the CLEAR button on  
the remote control to correct an entry.  
4. Press the FORWARD button to search ahead or the REVERSE button to  
search behind.  
5. Press the STOP button to end a Go-To search.  
40  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Commercial Advance  
®
This feature uses patented technology to detect and mark most commercials on your tape for  
any recording that is more than 15 minutes long. Once recording is finished, the VCR rewinds  
the tape to the beginning of the recording and determines where the commercials are located. It  
then marks the beginning and end of the detected commercial segments, and when finished,  
returns the tape to the end of the recording. It does not erase commercials from the tape.  
During playback, the VCR automatically skips the detected commercial segments, or you can  
chose to manually skip them. This feature reduces three minutes of commercials to  
approximately 8-12 seconds of fast forwarding in the SLP speed. You can select a background  
display of blue or see the video as the commercials are skipped.  
Because television signals do not indicate where commercials are located, this feature finds and  
marks them through a set of formulas based on how television is broadcast today. Since  
television stations broadcast differently and insert their own commercials, you may experience  
some variations in this features effectiveness. Station promotions, identifications, and  
announcements are not considered commercials, but might be skipped. For more information,  
see Questions and Answers About COMMERCIAL ADVANCE in the Reference section.  
All of the COMMERCIAL ADVANCE features are accessed through the  
COMMERCIAL ADVANCE menu.  
1. Press MENU to display the VCR MAIN MENU.  
2. Press 6 to display the PREFERENCES menu.  
3. Press 8 to display the COMMERCIAL ADVANCE menu.  
PREFERENCES  
1 Remote Control: VCR1  
2 Auto Play:  
ON  
3 Auto TV/VCR:  
4 EnergySaver:  
5 Front Panel:  
6 Tape Speed:  
7 Set Auto Repeat  
ON  
2:00  
AUTO  
SLP  
8 COMMERCIAL ADVANCE  
0 Exit  
Now you can select one of the COMMERCIAL ADVANCE features.  
COMMERCIAL ADVANCE  
COMMERCIAL ADVANCE Marking  
Press 1 to turn commercial Marking ON or OFF.  
1 Marking:  
2 Playback:  
3 Display:  
ON  
AUTO  
Blue  
Select ON, and the VCR will mark commercials within approximately 30  
seconds for the following types of recording:  
— Timer, Timer with VCR Plus+, or Express Recording Sets the  
0 Exit  
VCR to automatically mark commercials after the power is tuned  
off.  
The VCR is waiting to  
mark commercials in the  
program you recorded.  
— Recording Allows the VCR to prompt you to mark the  
commercials when youve stop the recording.  
1 Mark them now  
2 Mark them later  
3 Don't mark commercials  
Select OFF and the VCR will not mark the commercials.  
The VCR will begin  
marking in 30 seconds...  
Chapter 4  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
COMMERCIAL ADVANCE Playback  
Press 2 to switch between Playback: AUTO and MANUAL.  
COMMERCIAL ADVANCE  
1 Marking:  
2 Playback:  
3 Display:  
ON  
AUTO  
Blue  
Select AUTO to have the VCR automatically advance through the blocks of  
marked commercials.  
It works with most 30, 45, and 60-second commercials.  
0 Exit  
A commercial group starting with the first two minutes or last two minutes  
of a recording will not automatically be skipped.  
A commercial will not be skipped if a recording starts in the middle of a  
commercial segment, one isolated commercial is shown without others, or a  
commercial is longer than one minute. Press FWD on the VCR (FORWARD  
on remote) to scan through the commercial.  
Part of a recorded program may be skipped if the program segment is  
between commercials and less than one minute or there are frequent dark  
and quiet scenes.  
Select MANUAL and the VCR wont advance through the blocks of marked  
Timer Recordings and  
COMMERCIAL ADVANCE  
commercials until you press SEARCH.  
When using Timer Recordings  
to tape two back-to-back  
programs on the same  
channel, you may want to  
program each show  
separately so that the  
beginnings and ends of  
programs are not  
To Override Automatic Skipping  
If part of the program youve recorded is passed over, you can temporarily  
override the automatic skipping feature of COMMERCIAL ADVANCE.  
1. While the desired portion of the program is being skipped, press the PLAY  
or STOP button on the remote control or VCR front panel.  
2. To view the portion of the tape that was skipped, rewind the tape back to a  
position before the skipping started using the REVERSE (REV) button.  
automatically skipped by  
COMMERCIAL ADVANCE.  
3. Press the PLAY button to start playback. The portion of the tape will no  
longer be skipped.  
Automatic skipping will be enabled again after the VCR detects the end of  
the commercial group.  
Notes: If you press SEARCH during playback of material other than  
commercials, the VCR advances to the end of the next marked”  
commercial block and resumes playback.  
The VCR resumes playback when it reaches the end of the marked  
commercials.  
COMMERCIAL ADVANCE Display  
Press 3 to switch between Display: BLUE or VIDEO.  
Select BLUE to display a blue background when the VCR advances through  
the block of marked commercials.  
Select VIDEO to display the recorded video when the VCR advances  
through the block of marked commercials.  
42  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Movie Advance  
®
MOVIE ADVANCE helps you locate certain parts of prerecorded movies (rented or purchased).  
This feature works two ways: 1) you can go to the beginning of the movie, or, 2) you can skip  
from one preview to the next. MOVIE ADVANCE works only on tapes with the safety tab  
removed recorded in SP speed.  
1. To select MOVIE ADVANCE, insert a tape with its safety tab removed and  
press the SEARCH button on the remote control.  
2. Press 1 if the tape is a purchased or rented movie, press 2 if its a  
recording made at home, or press 3 if its something else, you dont know,  
or you do not want to select MOVIE ADVANCE.  
MOVIE ADVANCE  
What type of tape  
is this?  
1 Purchased/Rented Movie  
2 Home Recording  
3 Other  
Pressing 2 or 3 gives the same response and takes you to a different search  
feature. If you accidentally make a wrong selection, press STOPEJECT on  
the VCR (STOP on remote) and reinsert the tape. Press SEARCH.  
Press CLEAR to cancel  
If you press 1, the MOVIE ADVANCE menu appears.  
3. Press 1 to advance directly to the beginning of the movie or press 2 to view  
the first (next) preview.  
MOVIE ADVANCE  
Would you like to go to  
the start of the movie  
or to the next preview?  
Press 1 to Go To Movie. The following screen appears with a blue  
background.  
1 Go to movie  
2 Go to preview  
When the movie is found, you will see a message reading The movie is  
ready. Press PLAY to start.  
Press CLEAR to cancel  
Note: You can press the STOP button to cancel the MOVIE ADVANCE  
search.  
Press 2 to Go To Preview. The on-screen display will tell you that the  
VCR is looking for the start of the next preview.  
When a preview is detected, the VCR cues it and begins playing.  
MOVIE ADVANCE  
The movie is ready.  
Press PLAY to start.  
To Override the Show Previews Mode:  
Press the SEARCH button while a tape is being searched.  
Pressing the SEARCH button while:  
Press STOP to cancel  
The tape is reversing will begin searching for the start of the next preview  
or long commercial.  
The tape is searching forward for the next preview will reverse the tape  
back to the start current preview.  
The VCR is playing will advance the tape to the start of the next preview,  
long commercial, or the start of the movie (whichever comes first).  
Searching for preview  
Press SEARCH to reverse  
Press STOP to cancel  
Chapter 4  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
Pro-Tect PlusLocking Feature  
To protect set timer recordings and to disable the VCR for use, the unit can be locked so that the  
buttons on the front panel or remote control wont work.  
To Lock: Press and hold either the remote controls ONOFF or VCR button until the front  
panel display flashes.  
To Unlock: Press and hold either the remote controls ONOFF or VCR button until the  
front panel display flashes for several seconds. Unlocking is the only way to turn on and use  
the VCR.  
Tracking  
Your VCR has automatic tracking which removes streaks and noise from the picture. Automatic  
tracking is activated when you insert a tape or turn on the VCR. Occasionally you may need to  
manually adjust tracking, especially if the tape was recorded on a different VCR. Use the  
TRACKING /+ buttons on the VCR front panel or remote control to remove streaks and noise.  
You can also use tracking when pausing a tape to reduce the noise of the stilled picture.  
When manually adjusting the picture, automatic tracking is turned off. To turn automatic tracking  
back on, eject the tape and reinsert it.  
Note: Tracking has no effect when recordingonly during playback.  
Hours  
0:30:00  
Minutes  
Time Counter  
The time counter shows the actual time used when recording or playing back a  
tape. The time counter helps locate the beginning or end of recorded events. It  
resets to 0:00:00 whenever a tape is ejected from the VCR.  
Seconds  
For example, if you record a 30minute program at the beginning of a tape,  
rewind it, and then want to go to the end of the first program to start another  
recording:  
1. Press the INFO button twice to display only the time counter.  
2. Press the CLEAR button to reset the time counter to 0:00:00.  
3. Press the remote controls FORWARD button (FWD on the VCR) to advance  
a tape until the time counter reads 0:30:00.  
4. Press the STOP button. This is the approximate end of a 30-minute program  
(you may want to press the PLAY button to verify). When the tape is cued  
correctly, you can begin recording.  
5. Press the INFO button to remove the time counter from the screen and  
return to the normal display mode.  
44  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
On-Screen Displays  
Pressing the INFO button displays the status of the VCR (Stop, Play Record, etc.) as well as the  
channel number, time counter position, date, time, and tape speed on the TV screen.  
Note: The date and time must be set before they can be displayed.  
1. Press the INFO button to show the on-screen displays. The current time is  
1
Stop  
Ch 05  
0:30:00  
displayed in the VCRs front panel.  
11/18/01 Sun 1:30PM SLP  
On-screen display (times  
out)  
2. Press INFO again to have only the time counter remain on the screen. The  
0:30:00  
2
time counter is also displayed in the VCRs front panel.  
Time counter only (does  
not time out)  
3. Press INFO again to have no displays appear on the TV screen. The time  
counter remains in the VCRs display panel. This is useful for dubbing  
tapes.  
3
No displays will appear  
(useful for dubbing)  
4. Press the INFO button again to return to the normal display. The current  
time is displayed in the VCRs display panel.  
Note: Turning off the VCR also resets the displays.  
Chapter 4  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VCR Features  
AUDIO  
Audio Set-Up Features  
Your VCRs audio setup features affect both tape playback and recordings. The  
1 Reception:  
2 Tape Playback: HI-FI  
STEREO  
features in this section are accessed through the AUDIO menu.  
To Display the Audio Menu:  
1. Press the MENU button to bring up the VCR MAIN MENU.  
2. Press 7 to choose AUDIO.  
0 Exit  
With the AUDIO menu displayed, you are ready to select an item from the  
menu to set up.  
Reception  
Some TV programs are broadcast with stereo audio or a Second Audio Program  
(SAP) which offers a second language. The Reception feature lets you select the  
type of audio you want to record. Press 1 repeatedly to switch between  
Reception: STEREO, MONO, or SAP.  
STEREOused for normal or stereo broadcast TV recording. The HI-FI  
indicator lights on the VCR front panel when the VCRs tuned station is  
broadcasting in stereo.  
MONOused if the stereo signal is weak or the sound is too noisy.  
SAPused to hear/record a Second Audio Program instead of the normal  
audio on both the Hi-Fi and linear tracks.  
Tape Playback  
The VCR records the same audio on both the Hi-Fi stereo and linear tracks on  
the tape. Hi-Fi sound is recorded on separate left and right stereo channels.  
Monaural sound is recorded on the linear track. In the AUDIO menu, press the  
2 button repeatedly to switch between Tape Playback: Hi-Fi, LINEAR, and MIX.  
To enjoy Hi-Fi sound, connect your VCR to a stereo television or amplifier/  
receiver using the audio jacks. The Tape Playback feature lets you select which  
audio you play back.  
Hi-Fiuse to play back sound recorded on the Hi-Fi tracks and for normal  
use.  
LINEARuse to play back the sound recorded on the linear monaural track,  
such as a Second Audio Program, or a dubbed voice-over.  
MIXused to play back the sound recorded on both the linear track and  
the Hi-Fi track, sound-on-sound. The Hi-Fi indicator lights when MIX is  
active.  
46  
Chapter 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 5  
Other Information  
Chapter Overview:  
Troubleshooting  
COMMERCIAL ADVANCE Q&A  
Front, Rear, and Display Panel Diagrams  
Specifications  
Care and Cleaning  
Warranty Information  
Finding the TVs Video Line Input  
Advanced Connection Diagram  
Glossary  
Index  
Changing Entertainment. Again.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Troubleshooting Tips  
In this section, you will find answers to common recording, playback, and general VCR questions.  
Consulting with this section first when there is problem may help you answer common questions.  
General VCR Problems  
No power  
Check to make sure it is plugged into an operating outlet.  
Check to make sure your connections are correct.  
VCR does not respond to the remote control  
Check to make sure there are no objects between the VCR and the remote control.  
The remote controls batteries may need changing.  
You are not in VCR-controlling mode. Press the remote controls VCR button to control it.  
Theres poor or no picture for normal TV viewing  
Make sure the VCR indicator is off.  
Make sure the TV is switched to an active channel.  
Make sure the antenna connections are secure and correct.  
Rewind does not operate  
Check to make sure the tape is not already rewound.  
The clock shows an incorrect time or date  
There may have been a power interruption. Reset the VCRs time and date.  
Make sure the clock is set accurately (check AM/PM and date).  
Check the Daylight-Saving setting. The clock may have adjusted for Daylight-Saving Time.  
Time did not adjust for Daylight-Saving time.  
Check to make sure the Daylight-Saving Time feature is set correctly.  
The VCR makes noise when stopped  
The VCR is removing the tape from the playheads. This is normal. The head cylinder inside the VCR will  
continue to rotate for a few minutes after you put the VCR in the stop mode.  
Cannot select channels over 69  
Cable channels over 69 can only be selected if Signal Type: CABLE/ANTENNA feature is set to CABLE.  
TIMER flashes on the VCR front panel display  
The clock is not set.  
Check to make sure there is a cassette in the VCR when a timer recording is set ad the power is turned  
off.  
On-screen menus appear in English, French, or Spanish  
Check the LANGUAGE feature for the preferred on-screen language.  
48  
Chapter 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Recording Problems  
Will not record  
Make sure there is a recordable tape in the VCR.  
Eject then reinsert the tape.  
Make sure the tape is not broken.  
Make sure the VCR is not in pause mode. Press PAUSE or PLAY to return to normal playback.  
Make sure the Pro-Tect Plus feature is not active.  
A VCR Plus+ system or timer recording was not made or the wrong program recorded  
Make sure the correct PlusCode programming number is entered.  
Make sure the program was entered correctly (the wrong channel or times may be entered).  
Make sure the cable box or satellite receiver was turned on when recording was to begin.  
There may have been a power interruption. Reset the time and date.  
Check to see if time and date are correct including AM/PM.  
Make sure the program did not exceed the tapes length or that the tape was not rewound beforehand.  
Make sure the VCR was turned off at the time recording started.  
Make sure there was a tape in the VCR with its safety tab intact.  
The VCR ejects tapes when the end is reached during a timer recording.  
Make sure the VCR Plus+ system setup was completed correctly.  
Will not record  
Make sure the tapes safety tab is intact.  
Make sure the VCR is not in Video Line Input mode. Press INPUT on the remote control to return to  
normal viewing.  
Playback Problems  
Snowy or no picture during playback  
Press the remote controls TVVCR button to activate VCR-controlling mode. VCR appears in the front  
panel display when active.  
Check the TV channel selected (3 or 4) to make sure it matches the channel selected with CH. 3/4  
switch on the back of the VCR.  
Check to make sure the TVs fine tuning is correct for the channel selected.  
If you use A/V cables and jacks to connect the VCR to the TV, check all connections for snug and  
correct connections.  
Check to make sure the TV monitor is set to Video Line Input (see How to Find Your TVs Video Line  
Input in this section of the manual for detailed information).  
Try another tape.  
Some snow/streaks are normal during search, stop action, frame advance, and slow-motion playback.  
Chapter 5  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Streaks in picture during normal playback  
Press one of the TRACKING buttons to move streaks up or down for the best picture.  
Check to make sure the tape is of good quality and not worn out.  
Time counter not working or time counter not working in search modes  
The time counter does not advance during unrecorded portions of tape. When an unrecorded segment of tape is  
encountered, the time counter will hold its count until recorded material is detected again.  
A minus () will appear in front of the time if you rewind the tape farther back than a counter reading of 0:00:00.  
The time counter disappears during search; this is normal.  
Will not play  
Check to make sure there is a tape in the VCR.  
Try ejecting and reinserting the cassette.  
Check to make sure the tape is not broken.  
Check to make sure the VCR is not in pause mode. Press PAUSE or PLAY to return to normal playback.  
Check the Pro-Tect Plusfeature.  
Will not Auto Channel Search active channels correctly  
Check to make sure the antenna connections are secure and correct.  
Check to make sure the Signal Type: CABLE/ANTENNA feature is set correctly.  
If Detect Automatically was selected for the Signal Type in the AUTO CHANNEL SEARCH menu, try using either  
CABLE TV or ANTENNA instead.  
May not be necessary if using a cable box for all channels. Contact your local cable company for more information.  
Tape plays back in slow motion  
Press PLAY to return to normal playback.  
Cassette with safety tab removed does not start to play automatically  
Check to make sure the AUTO PLAY ON/OFF feature is set to ON.  
Time counter disappears during searching  
This is normal.  
There is no stereo sound during playback  
Make sure the Tape Playback feature is set to Hi-Fi to hear stereo sound during playback.  
You must use A/V cables (not provided) and jacks to connect the VCR to the TV (or stereo) to hear true stereo  
sound during playback.  
The stereo Audio is too noisy  
The stereo signal is weak. Set the Reception: STEREO/SAP/MONO to MONO.  
Press either the TRACKING or + button to minimize picture noise.  
50  
Chapter 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Questions and Answers About  
®
Will commercials be scanned through only on playback of recordings?  
Yes. The VCR rewinds and marks commercial segments after a recording is finished.  
How fast does this feature scan through commercial breaks?  
In SLP tape speed, a 3-minute commercial break is scanned through in approximately 8-12  
seconds. In SP, it takes about 25-35 seconds.  
Are commercials still recorded if I want to watch them?  
Yes. The recorded program, including commercials, can be viewed by setting the Playback  
feature to MANUAL.  
What if the VCR scans forward through part of my program?  
Press PLAy or STOP while the tape is being automatically skipped. rewind the tape back to a  
position before skipping started, then press PLAY.Automatic skipping will start again after the  
end of the commercial group is detected by the VCR.  
Once a recording has been marked, does COMMERCIAL ADVANCE work each time  
the tape is played?  
Yes. If the Playback feature is set to AUTO, the marked commercials should be skipped each  
time the tape is played in a COMMERCIAL ADVANCE VCR.  
After marking commercials, is the tape left at the beginning or end of the  
recording?  
The tape is left at the end of the recording so it is in position to begin additional programmed  
recordings.  
Does the marking process interfere with other programmed recordings?  
No. If two or more recordings are programmed together without sufficient time to mark the  
first recording, marking will take place after all recordings are completed.  
What happens if the marking process is interrupted?  
Marking can be interrupted to allow use of the VCR. Marking will resume again when the  
VCRs power is turned off as long as the tape has not been ejected from the VCR.  
Does COMMERCIAL ADVANCE work in all recording speeds?  
Yes, COMMERCIAL ADVANCE works in SP and SLP.  
Will COMMERCIAL ADVANCE marked recordings work in non-Commercial Advance  
VCRs?  
A COMMERCIAL ADVANCE marked recording will play in a non-Commercial Advance VCR,  
but commercials will not automatically be skipped.  
Chapter 5  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
.
Front Panel  
AUDIO (LEFT and RIGHT) and VIDEO In Jacks Receives signals from another component (like  
another VCR or camcorder) when connected to the VCR using A/V jacks. Use the INPUT button to  
select L2 to record from these jacks (L1 indicates the rear panel A/V jacks being active).  
CHANNEL TRACKING Up and Down Adjusts the image quality by removing picture noise”  
and distortion.  
FWD Forwards the tape when the VCR is stopped. Searches the picture forward during playback.  
Starts slow motion during play-pause and increases slow-motion speed.  
PLAYPAUSE Plays a tape. Pauses action for viewing during playback. Pauses recording to  
prevent recording of unwanted scenes.  
POWER Turns the VCR on or off.  
RECORD Starts VCR recording. Also used for Express Recording (XPR).  
REV Rewinds the tape when the VCR is stopped. Searches the picture in reverse during  
playback. Starts slow motion during play-pause and decreases slow-motion speed.  
STOP/EJECT A single press of this button stops normal VCR functions such as record, playback,  
rewind, fast-forward, or pause. If pressed a second time, this button ejects an inserted tape.  
TVVCR Switches the picture signal so that it either comes from the VCR or the TV cable/antenna  
signal.  
52  
Chapter 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
REC  
AM  
VCR  
Display Panel  
Clock/Counter Displays current time, time counter, tape speed, or channel numbers when switching  
channels.  
FUNCTION DISPLAYS:  
dn & Ld (Down and Load) Front panel display alternates between these two words when time data is  
being downloaded.  
REC (Recording indicator) The VCR is recording. REC flashes on the front panel display when a recording is  
paused.  
(Timer indicator) Displayed when an Express Recording (XPR) or timer recording is under way or when  
the VCR is set for a timer recording and the power is turned OFF. TIMER flashes on the VCR front panel when a  
timer recording is set and no tape is inserted in the VCR.  
VCR indicator Indicates that the VCR is in VCR-display mode. Press the TVVCR button to toggle between  
VCR and TV viewing modes.  
VCR indicator is ON when the picture displayed is from the VCRs tuner.  
VCR indicator is OFF when the picture displayed is from the TVs tuner.  
Chapter 5  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
ANT. IN  
RF OUT  
AUDIO  
R
L
IN  
OUT  
CH.  
3
4
VIDEO  
Back Panel  
CH. 3/4 switch Determines the channel to which the TV must be tuned in order to see the VCRs  
picture. Not used when connecting the VCR to the TV using A/V cables.  
AUDIO (LEFT and RIGHT) and VIDEO IN jacks Receives signals from another component, such  
as another VCR or camcorder, when connected to these jacks. Use the INPUT button on the VCR or  
remote control to select the rear video line input A/V jacks (L1) to record from these jacks.  
AUDIO (Right and Left) and VIDEO OUT jacks Sends signals from the VCR to another  
component, like a TV or another VCR, when the other component is connected to these jacks.  
ANT. IN jack Receives a signal from an antenna or cable system when the VCR is attached with RF  
cables.  
RF OUT jack Passes the VCRs signal to a TV using the supplied RF cable.  
54  
Chapter 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Specifications  
Format:  
VHS  
Record/Playback  
System:  
Video: 4-head  
Audio: VHS Hi-Fi record/playback system  
Video Signal System: EIA standard: NTSC color  
Antenna:  
75-ohm external VHF/UHF combined  
antenna terminal  
Tuner:  
USA:  
181 channels capability*  
(125 cable channels)  
Canada:  
178 channels capability*  
(122 cable channels)  
Type:  
AutoProgramming frequency synthesis  
Power Requirement: 120V AC, 60 Hz  
Power Consumption: 17 watts (standby < 3 watts)  
Dimensions:  
3.64 inches high (91 mm)  
14.4 inches wide (360 mm)  
9.4 inches deep (230 mm)  
Weight:  
Other:  
6.4 pounds (2.9 kg)  
Automatic head cleaner  
Storage Temperature - 22˚F to +149˚F  
Range:  
(-30˚C to +65˚C)  
Operating  
+41˚F to +104˚F  
Temperature Range:  
(+5˚C to +40˚C)  
*Check your cable companys compatibility requirements.  
Cleaning the VCR  
Use a soft cloth or dusting attachment of your vacuum cleaner to dust your VCR. Remove dust from  
the ventilation holes on the top, back, sides, and bottom of the VCR and all connected components.  
Plastic surfaces are easily scratched and can be marred by alcohol and various solvents. Avoid  
excessive use of oil-based furniture polishes since the materials used in the cabinet will accumulate  
more dust. We recommend using a nonabrasive, antistatic cleaner and polisher.If part of the  
program is skipped, rewind the tape to the beginning of the skipped program segment and press  
PLAY.  
Chapter 5  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
RCA VCR Limited Warranty  
What your warranty covers:  
Any defect in materials or workmanship.  
For how long after your purchase:  
90 days for labor charges.  
One year for parts.  
The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm, whichever  
comes first.  
What we will do:  
Pay any Authorized RCA VCR Service Center the labor charges to repair your VCR.  
Pay any Authorized RCA VCR Service Center for the new or, at our option, refurbished replacement parts required to  
repair your VCR.  
How you get service:  
Take your VCR to any Authorized RCA VCR Service Center. To identify your nearest Authorized RCA VCR Service  
Center, ask your dealer, look in the Yellow Pages, or call 1-800-336-1900.  
Show the Authorized Service Center Representative your evidence of purchase date or first rental.  
Pick up your VCR when repairs are completed.  
What your warranty does not cover:  
Customer instruction. (Your Owners Manual clearly describes how to install, adjust, and operate your VCR. Any  
additional information should be obtained from your dealer.)  
Installation and related adjustments.  
Signal reception problems not caused by your VCR.  
Damage from misuse or neglect.  
Cleaning of video/audio heads.  
Batteries.  
A VCR that has been modified or incorporated into other products or is used for institutional or other commercial  
purposes.  
A VCR purchased or serviced outside the U.S.A.  
Acts of nature, such as but not limited to lightning damage.  
Product Registration:  
Please complete and mail the Product Registration Card packed with your VCR. It will make it easier to contact you  
should it ever be necessary. The return of the card is not required for warranty coverage.  
How State Law relates to warranty:  
This warranty gives you specific legal rights and you also may have other rights that vary from state to state.  
If you purchased your VCR unit outside the United States:  
This warranty does not apply. Contact your dealer for warranty information.  
Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs  
of such service calls are the sole responsibility of the purchaser.  
56  
Chapter 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Finding the TVs Video Line Input  
You need to tune your TV to the video line input if you are using the  
VCRs Audio/Video (A/V) OUT jacks to connect to the TVs A/V input  
jacks. You must select the TVs video line input before you can see the  
VCRs menus, the cable/antenna reception, and the content thats on a  
tape.  
TV Button  
ONOFF  
TV  
VCR  
The video line input for TVs varies by brand and model. Below are some  
REVERSE  
PLAY  
FORWARD  
steps to try to find your TVs video line input:  
If your TV brand is RCA, GE, or Proscan, press the TV button on the  
VCRs remote control, then press the INPUT button.  
RECORD  
INFO  
STOP  
PAUSE  
If you have another brand of TV, see the chapter Using the Remote  
Control to see if the VCRs remote can be programmed to control your  
TV. If so, once completed, follow the step above.  
SEARCH  
If those options do not work, try the following ideas. You might access the  
video line input by:  
MUTE  
GO BACK  
SPEED  
Pressing a button on the TVs remote control (see the table below).  
Selecting a specific channel from the TVs on-screen menu system (see  
CLEAR  
MENU  
the table below).  
1
3
2
5
8
0
Tuning directly to the video line input by selecting a specific channel  
number (see the table below)  
6
9
4
7
Going through all available channels by pressing the channel up or  
down buttons on the TV or its remote control.  
Common Video Line Input scenarios:  
TRACKING  
F.ADV  
INPUT  
Button  
Video Input Channel Variations  
Button/Switch  
on the TV  
Button on the  
TV Remote  
Channel  
Number  
VIDEO  
SIGNAL  
VID 1  
VID 1  
LINE  
VID  
00  
90  
91  
VID 2  
S-VID  
S-VIDEO  
VIDEO  
S-VID  
INPUT  
S-VIDEO  
SOURCE  
AUX  
92  
93  
VID 1  
VID 2  
Chapter 5  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Advanced Connection  
TV + VCR + Satellite Receiver  
Using A/V and RF Coaxial Cables  
Note: Your satellite receiver and television back panels may not look exactly like the models  
shown here. This connection can also be used for a cable box.  
1. Connect the VCR to the TV  
A. Connect one end of the supplied RF  
coaxial cable to the RF OUT jack on  
the back of the VCR and the other end  
to the TVs antenna input jack.  
TV  
AUDIO  
VIDEO  
L / MONO  
L
R
IN  
B. Connect the A/V cables. Connect audio  
cables to the VCRs R and L Audio OUT  
jacks and the other ends to the TVs  
corresponding audio input jacks (if your  
TV only has one audio input jack, use  
the VCRs L audio jack to connect).  
Connect one end of the video cable to  
the VCRs VIDEO OUT jack, and the  
other end to the TVs video input jack.  
OUT  
CABLE/  
ANTENNA  
S-VIDEO  
1A  
1B  
VCR  
AUDIO  
ANT. IN  
R
VCR  
L
RF OUT  
OUT  
IN  
CH  
3
4
VIDEO  
2. Connect the satellite receiver to the VCR  
A. Connect one end of a second RF coaxial  
cable (not included) to the VCRs ANT.  
IN jack. Connect the other end to the  
satellite receivers antenna output jack.  
2B  
SATELLITE  
RECEIVER  
2A  
IN FROM ANT  
OUT TO TV  
CH3  
CH4  
OUT  
L
SATELLITE  
IN  
B. Connect the A/V cables. Connect audio  
cables to the VCRs R and L audio IN  
jacks and the other ends to the satellite  
receivers audio output jacks. Connect  
one end of the video cable to the VCRs  
VIDEO IN jack, and the other end to  
the satellite receivers video output  
jack.  
VIDEO  
R
S-VIDEO  
3
4
From Cable  
or TV Antenna  
From  
Satellite  
3. Connect a TV antenna or cable feed to the satellite receiver  
If you have cable or a standard TV antenna, connect its RF coaxial cable (not included) to the  
antenna input jack on the satellite receiver.  
4. Connect the satellite antennas cable to the satellite receiver  
Connect the satellite antennas RF coaxial cable feed (not included) to the receivers satellite  
input jack.  
Note: To hear stereo output from the satellite receiver, you must use the TVs video line input  
channel.RF coaxial cable only carries mono sound.  
58  
Chapter 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other Information  
Glossary  
A/V Jacks & Cables Commonly called RCA-typecables. Improves  
picture and sound quality over RF Coaxial cables. A/V cables are required  
for stereo audio.  
EnergySaver Automatically turns the VCR off after a user-defined  
period of inactivity.  
Express Recording (XPR) A method of timer recording which tapes  
for a set period of time using 30-minute increments.  
Pro-Tect PlusAllows the VCR to be disabled so that the front panel  
and remote control buttons dont work. Useful for protecting timer  
recordings.  
QuickSet Guide An first-time use, interactive, menu-based system that  
walks you through several setup steps in a series of questions. The  
QuickSet Guide is also available in the VCRs Main Menu.  
SAP (Second Audio Program) A second sound track that may be  
included with a stereo broadcast. Usually used for foreign language dubs  
of programs.  
VCR Channels List The active list of channels available to the VCR  
using the CHANNEL +/- buttons.  
XPR See Express Recording above.  
Chapter 5  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Index  
A
D
M
ADD/REMOVE CHANNELS screen  
18  
Date and time setting 19  
Design specifications 55  
Display panel 53  
MENU button  
16, 26, 33, 35, 41, 46  
MOVIE ADVANCE  
Overriding 43  
Audio features, set up 46  
AUDIO IN jacks 58  
Displays, on screen 45  
AUDIO menu 46  
Movie Advance 43  
MUTE button 27  
Audio/Video (A/V) jacks 17, 52, 54  
AUDIO/VIDEO jacks 26  
Auto channel search 17  
Auto clock feature 19  
Auto play feature 13, 21  
Auto TV/VCR feature 22  
Automatic rewind 13  
Automatic tracking 13, 44  
E
EJECT button 13  
N
EnergySaver feature 22  
Express Recording (XPR) 2, 32  
Number buttons 20, 26, 27  
F
O
F. ADV button 26, 39  
FORWARD button 13, 39  
Frame advance 39  
OFF button 26, 27  
ONOFF button 44  
On-screen displays 45  
Overheating 6  
B
Back panel jacks 54  
Front panel controls 52  
FWD button 38, 39, 44  
Basic recording 13  
Batteries (remote control) 11  
Broadcast stereo TV recording 38  
P
G
PAUSE button 13, 27, 38  
Picture search options 39  
PLAY button 13, 27, 38  
PLAY/PAUSE button 39  
POWER button 13  
Power surges 6  
PREFERENCES menu 21, 41  
Pro-Tect Plus locking feature 44  
C
Glossary 59  
GO BACK button 26, 27  
Cable box setup 16  
Cables  
positioning 6  
I
CHAN buttons 27  
CHANNEL buttons 17, 26  
Channels, adding/removing 18  
CHANNELS menu 16, 18, 35  
CLEAR button 26, 27, 40  
Clock display 53  
COMMERCIAL ADVANCE 41  
Display 42  
Index search 40  
Indicators in display panel 53  
INFO button 26, 27, 44  
INPUT button 27  
Q
INPUT button 26, 33, 38, 57  
QuickSet guide 16  
Marking 41  
Playback 42  
questions and answers 51  
Component buttons 26  
Connections 8  
L
R
L1 indicator 38  
L2 indicator 38  
LANGUAGE menu 16  
Locking feature 44  
REC display 53  
Reception: STEREO/MONO/SAP  
feature 38, 46  
Controls  
back panel 54  
RECORD button 13, 27, 32, 38, 52  
front panel 52  
Copying tapes 38  
60  
Chapter 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Recording  
basic 13  
Speed  
SLP 23  
VCR Plus+  
channel lists 36  
broadcast stereo TV 38  
SP 23  
channel worksheet 37  
VCR Plus+ SILVER System 34  
VCR Plus+ System Worksheet 37  
VCR viewing channel 11, 13  
Video Input Channel 57  
VOL buttons 27  
copying /editing tapes 38  
Express (XPR) 2, 32  
SAP 38  
speeds 23  
timer 33  
SPEED button 13, 23, 27, 32  
Speeds, recording 23  
STOP button 13, 27, 32, 38, 52  
Remote  
T
component buttons 26  
TV function buttons 27  
Remote, batteries 11  
Tab, safety 13  
Tape eject 13  
Tape playback feature 46  
Tape playback: HI-FI/LINEAR/MIX  
46  
Removing/adding channels 18  
REV button 27, 38, 52  
REVERSE button 13, 39  
Reviewing timer programs 33  
Rewind, automatic 13  
RF OUT jack 54  
Tape speeds 23  
Time and date 19  
Time counter 44  
Time counter display 45  
Time display on TV 45  
TIME menu 19  
S
Time setting  
Safety tab 13, 21  
SAP 38  
Daylight-saving 20  
set time zone 19  
Search  
Timer programs  
forward 39  
clearing 33  
reverse 39  
reviewing 33  
SEARCH button 27, 40  
Set up  
Timer recording 33  
stopping 33  
auto play feature 21  
auto TV/VCR feature 22  
cable box 16  
Daylight-Saving 20  
front panel 22  
language feature 16  
PREFERENCES menu 21  
tape speed feature 23  
time and date 19  
time zone 19  
TRACK buttons 27  
Tracking 44  
TRACKING buttons 13, 39, 44  
Troubleshooting 48  
TV button 26, 57  
TV function buttons 27  
TVVCR button 22, 27, 38  
V
VCR  
connecting 8  
VCR button 26  
VCR function buttons 26  
VCR indicator 38, 53  
VCR MAIN MENU 16, 19, 46  
using menu system 16  
Signal type  
changing 18  
selecting 18  
Slow motion 39  
Specifications 55  
Chapter 5  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Please do not send any products to the  
Indianapolis address listed in this manual or on  
the carton. This will only add delays in service  
for your product.  
Thomson multimedia Inc.  
10330 North Meridian Street  
Indianapolis, IN 46290  
©2001 Thomson multimedia Inc.  
Trademark(s)® Registered  
Marca(s) Registrada(s)  
Printed in Korea  
TOCOM 15708270  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pyramid Car Audio Car Amplifier PB1281X User Guide
QSC Audio Stereo Amplifier SRA 1222 User Guide
Radio Shack Headphones 43 217 User Guide
RCA CRT Television J24F635 User Guide
RCA Microcassette Recorder RP5120 User Guide
RCA TV DVD Combo RCRVD2022 User Guide
Renesas Network Card M16C 6N User Guide
Ryobi Router 4950301 User Guide
SanDisk Computer Drive DC 000255 User Guide
Sears Fitness Equipment 83115934 User Guide