OWNER’S MANUAL
26/32” TFT LCD DIGITAL TV WITH DVD PLAYER
L26HD32D
L32HD32D
Digital Television Transition Notice
This device contains a digital television tuner, so it should receive digital over the air TV programming, with a
suitable antenna, after the end of full-power analog TV broadcasting in the United States on February 17, 2009.
Some older television receivers, if they rely on a TV antenna, will need a TV Converter to receive over the air digital
programming, but should continue to work as before for other purposes (e.g., for watching low-power TV stations
still broadcasting in analog, watching pre-recorded movies, or playing video games). When a Converter is used
with an older television receiver, a signal splitter might be necessary to continue to receive low-power analog
broadcasts via an antenna. For more information, please see www.DTV.gov. For information on the TV Converter
program, and on government subsidized coupons that may be used toward the purchase of one, see www.
dtv2009.gov, or call the NTIA at 1-888-DTV-2009.
ATTENTION
If you purchase a universal remote control from your local retailer, please contact the remote manufacturer for the
required programming code.
AIR/CABLE MODE SELECTION
When shipped from the factory, the Signal Type option is set to the “Cable” (Cable Television) mode.
If not using Cable TV, set this menu option to the “Air” position.
Before operating the unit, please read this manual thoroughly.
51F0101B_eng.indd
1
4/4/08 10:04:02 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a clean dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade and the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician to replace the obsolete receptacle.
10) Protect the power cord from being walked on or pinched particularly at plug, and the point where it exits
from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
PORTABLE CART WARNING
(symbol provided by RETAC)
13) Unplug this apparatus during lightning storms or when unused for long periods
of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug
damage, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
S3126A
15) Apparatus should not be exposed to dripping or splashing, and objects filled with liquids, such as vases,
should not be placed on the apparatus.
16) An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.
17) Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
18) Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
19) If an outside antenna or cable system is connected
to the unit, be sure the antenna or cable system is
ANTENNA
LEAD IN WIRE
grounded to provide some protection against voltage
surges and built-up static charges, Section 810 of the
GROUND
CLAMP
National Electrical Code, ANSI/NFPA 70, provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC SERVICE
EQUIPMENT
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes, and
requirements for the grounding electrode.
GROUND CLAMPS
NEC-NATIONAL
ELECTRICAL CODE
S2898A
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
3
51F0101A_eng.indd
3
3/5/08 5:05:45 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (continued)
20) When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
21) Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
22) Keep your fingers clear of the disc slot as it is closing. It may cause injury.
23) When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's
manual of the other equipment carefully and follow the instructions when making any connections.
24) Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume
sound may cause hearing or speaker damage.
25) Do not allow the product to output distorted sound for an extended period of time. It may cause speaker
overheating and fire.
26) When you use the headphones, keep the volume at a moderate level. If you use the headphones
continuously with high volume sound, it may cause hearing damage.
27) Do not look into the opening of the disc slot or ventilation opening of the product to see the source of the
laser beam. It may cause eye damage.
28) Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
29) This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.
CONDENSATION
Moisture will form in the operating section of the player if the player is brought from cool surroundings into a warm
room or if the temperature of the room rises suddenly.When this happens, player's performance will be impaired.
To prevent this, let the player stand in its new surroundings for about an hour before switching it on, or make sure
that the room temperature rises gradually.
Condensation may also form during the summer if the player is exposed to the breeze from an air conditioner. In
such cases, change the location of the player.
HOW TO HANDLE THE LCD PANEL
• Do not press hard or jolt the LCD panel. It may cause the LCD panel glass to break and injury may occur.
• If the LCD panel is broken, make absolutely sure that you do not touch the liquid in the panel. This may cause
skin inflammation.
If the liquid gets in your mouth, immediately gargle and consult with your doctor. Also, if the liquid gets in your
eyes or touches your skin, consult with your doctor after rinsing for at least 15 minutes or longer in clean water.
4
51F0101A_eng.indd
4
3/5/08 5:05:46 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
The unit emits heat when in operation. Do not place any covers or blankets on the unit, this may cause
overheating. Do not block ventilation holes, or set up near radiators. Do not place in direct sunshine. When
placing on a shelf leave 10 cm (4 inches) free space around the entire unit.
10cm
10cm
Notes when mounting the LCD TV/DVD on a wall
If the unit is to be mounted on the wall, contact the retailer where you purchased the LCD TV/DVD for advice,
and have the equipment professionally installed. Incomplete or improper installation may cause injury to you,
and/or damage to the LCD TV/DVD.
IMPORTANT NOTICE
Possible Adverse Effects on LCD Panel: If a fixed (non-moving) pattern remains on the LCD Panel for
long periods of time, the image can become permanently engrained in the LCD Panel and cause subtle but
permanent ghost images. This type of damage is NOT COVERED BY YOUR WARRANTY. Never leave your
LCD Panel on for long periods of time while it is displaying the following formats or images:
• Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.
• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on
a normal (4:3) display (black bars at top and bottom of screen); or viewing normal style (4:3) media on a
widescreen (16:9) display (black bars on left and right sides of screen).
The following symptoms are not signs of malfunction but technical limitation. Therefore we disclaim
any responsibility for these symptoms.
• LCD Panels are manufactured using an extremely high level of precision technology, however sometimes
parts of the screen may be missing picture elements or have luminous spots.
This is not a sign of a malfunction.
• Do not install the LCD Panel near electronic equipment that is susceptible to electromagnetic waves. Some
equipment placed too near this unit may cause interference.
• Effect on infrared devices – There may be interference while using infrared devices such as infrared cordless
headphones.
5
51F0101A_eng.indd
5
3/5/08 5:05:46 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
LCD color TV With DVD/CD player
Unique space saving design combines a 26/32” LCD color TV and a DVD/CD player.
A DVD disc has much more capacity, but is the same size as an audio CD disc. The Picture/Audio quality of a
DVD exceeds other software. The picture quality is higher than Super VHS video cassettes. The audio quality
is higher than an audio CD. The DVD also has special options; audio language selection, subtitle language
selection, or multi-angle, etc.
The DVD PLAYER can play back both audio CDs and MP3/WMA/JPEG CDs.
Compatible with a wide range of DVD audio outputs
Digital Audio Jack (Coaxial)
• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the
effect of being in a movie theater or a concert hall.
• Surround standard is different from Dolby Digital. This format is already in use in many theaters. By connecting
this unit to a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs
recorded in this format can be enjoyed. However, audio will not be output from the analog audio output jacks.
• By connecting this unit to an AV amplifier with a built-in MPEG decoder, the MPEG audio of DVD discs
recorded in this format can be enjoyed.
• The Linear PCM sound of a 48 kHz/24 bit through 96 kHz/24 bit exceeds audio CD sound.
Convenience Features
Direct selection of your desired scenes using Title/Chapter/Time/Track - You can play back from the
desired scene.
Recalling Up to 3 Scenes - You can program up to 3 scenes in memory and recall the marked scenes.
Frame Advance - The PAUSE/STILL moves one frame at a time.
Slow Motion - The SLOW moves you back and forth through the program by 4 steps of 1/7-1/2 times.
Repeat Playback -You can repeat chapter, track, title, sides or material between two selected points.
Program Playback (Audio CD/MP3/WMA CD) - You can play back tracks in programmed sequences.
Zoom -You can zoom in the selected subject on the screen during playback.
Note: Make sure that discs are suitable for the following functions.
Multi-Language - Maximum 32 language subtitles and maximum 8 language soundtracks can be played back
for movies or programs.
Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc,
you can change the angles during playback.
Parental Control - You can limit the play back of scenes or sounds of DVD discs that have a rating level
encoded on the disc.
Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor.
TV Features
Integrated Digital Tuner -You can view digital broadcasts without using a Digital TV Set-Top Box.
Closed Caption Decoder With Full Text Mode - Displays text captions or full screen text on the screen for
hearing impaired viewers.
Picture Adjustments Using The Remote Control - The On-Screen display allows precise remote control
adjustment of BRIGHTNESS, CONTRAST, COLOR, TINT and SHARPNESS.
Programmable TV Sleep Timer - Operable from the remote control, the TV can be programmed for up to 120
minutes to turn off automatically.
On-Screen 3 Language Display - You can select one of 3 languages, English, Spanish or French for on-
screen programming.
V-Chip - The V-Chip function can read the rating of a TV program or movie content if the program is encoded
with this information. V-chip will allow you to set a restriction level.
* This product incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision,
and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is prohibited.
* is a trademark of DVD Format/Logo Licensing Corporation.
* Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
*
Manufactured under license under U.S. Patent #: 5,451,942 & other U.S. and worldwide patents issued &
pending. DTS and DTS Digital Out are registered trademarks and the DTS logos and Symbol are trademarks
of DTS, Inc.© 1996-2007 DTS, Inc. All Rights Reserved.
* HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
6
51F0101A_eng.indd
6
3/5/08 5:05:46 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Before using your unit
DVD operation
Preparation .....................................................25
Status display of disc ......................................25
Playback procedure........................................26
Special playback.............................................26
MP3/WMA/JPEG and Audio CD playback......27
Setting the JPEG interval................................28
Program playback (CD) ..................................28
Repeat playback (CD).....................................29
Random playback (CD) ..................................29
Zooming..........................................................29
Locating desired scene...................................29
Repeat playback.............................................30
Marking desired scenes..................................30
Changing soundtrack language ......................30
Subtitles..........................................................31
Changing angles.............................................31
Title selection..................................................31
DVD menu ......................................................31
Setting the language.......................................32
Setting the aspect ratio of TV screen ..............32
Setting on screen display................................32
Setting the picture mode.................................32
Night Mode .....................................................33
Digital Out.......................................................33
Parental control...............................................33
Temporary disabling of rating level
IMPORTANT SAFETY INSTRUCTIONS...........3
SAFETY PRECAUTIONS .................................5
IMPORTANT NOTICE.......................................5
Features............................................................6
Contents ...........................................................7
Disc...................................................................8
Location of controls...........................................9
Remote control ...............................................11
Power source..................................................12
Antenna connections ......................................13
Cable TV connections.....................................14
TV operation
Setting the on-screen language ......................15
Memorizing channels......................................15
TV operation ...................................................16
Labeling channels...........................................17
Labeling video inputs......................................18
Setting the V-Chip ...........................................18
Closed Caption...............................................20
CC advanced..................................................20
Adjusting the picture preference .....................21
Picture control adjustment ..............................21
Selecting the color temperature ......................21
Setting the picture size....................................22
Film Mode.......................................................22
Picture control adjustment in the PC mode .....23
DNR................................................................23
Sound control adjustment...............................23
Selecting Stereo/Second Audio Program
(SAP) ..............................................................23
Selecting the audio language..........................24
Selecting the HDMI audio input source...........24
Turning off the built-in speakers ......................24
Adjusting the back lighting ..............................24
Setting the Auto Shut Off ................................25
Resetting your settings ...................................25
by DVD disc ....................................................34
Additional information
Language code list..........................................35
Connections to other equipment.....................36
Reception disturbances ..................................39
Problems and troubleshooting ........................40
Specifications .................................................42
Limited Warranty.............................................43
7
51F0101A_eng.indd
7
3/5/08 5:05:47 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc
Playable discs
CAUTION:
Disc type and logo mark
content
• Only the left types of discs can be played on this
unit. DVD-ROM, CD-ROM, SVCD, CVD, VCD, etc.
cannot be played.
Audio
+
• 8cm discs can be played directly. If an 8cm disc
adapter is used it will cause errors.
• If you insert an irregular shaped disc, it may get
stuck and cause a malfunction.
DVD Video
Video
(moving
pictures)
• The use of a ring protector or other disc
accessories will cause errors.
CD-DA
Audio
• This unit is to be used exclusively with the NTSC
color system. PAL and SECAM system discs cannot
be used with this unit.
• Some CD-R/RWs and DVD-R/RW can not be
played back depending on the recording conditions.
The following discs are also available.
• DVD-R/RW discs of DVD video format.
• CD-R/RW discs of MP3/WMA/JPEG.
Region Number
Region number (Regional restriction code) is built-in to the unit and DVD video discs.
Region number “1” or “ALL” of DVD video discs can be used on this unit.
ALL
1
Title
DVD DISC
When two or more movies are recorded on a disc, the disc
is divided into two or more sections. Each section is called
a “TITLE”.
TITLE 1
TITLE 2
CHAPTER 1
CHAPTER 2
CHAPTER 1
CHAPTER 2
CHAPTER 3
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Audio - CD
Track
An Audio CD can contain several items.
These are assigned to the tracks.
TRACK
1
TRACK
2
TRACK
3
TRACK
4
TRACK
5
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe the disc in a circular motion.
• Do not use liquid or aerosol cleaners.
8
51F0101A_eng.indd
8
3/5/08 5:05:47 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of controls
Front
Remote sensor
POWER indicator
Left side
DISC slot
EJECT button
VOLUME +/– buttons
CHANNEL /1 (PLAY) button
CHANNEL /3 (STOP) button
MENU button
INPUT/ENTER button
POWER button
To display the menu screen.
Press MENU button to display the menu screen.
CHANNEL
setting during the menu screen operations.
/
buttons, VOLUME +/– buttons and INPUT/ENTER button can be used to select the desired
9
51F0101A_eng.indd
9
3/5/08 5:05:48 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Location of controls
(continued)
Rear side
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:SHOCK HAZARD-DO NOT OPEN.
A
VIS:RISQUE DE CHOC ELECTRIQUE-NE AS OUVRIR
P
ANT
AC INPUT
COAXIAL DIGITAL AUDIO OUT jack
VAR (VARIABLE) AUDIO OUT jacks
PC MONITOR IN jack
HDMI 2 IN jack
HDMI 1/DVI IN jack
ANT
AC INPUT
PC/DVI AUDIO IN jack
AC INPUT jack
LINE 2 VIDEO
IN jack
RF (ANT) IN jack
LINE 1 IN jacks
(VIDEO/S-VIDEO/AUDIO(L/R))
COMPONENT IN jacks
AUDIO (L/R) jacks
(for COMPONENT IN and LINE 2 VIDEO IN)
10
51F0101A_eng.indd 10
3/10/08 10:56:10 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
POWER
Power On/Off
DISPLAY/–
Call TV information
Call DVD information
Input “–” for digital channels
TV/DVD
(EJECT)
0-9
Switch between TV/AV and DVD
Eject a disc
Direct channel selection of TV
Input setting
Enter a password
VOL +/–
MUTE
Adjust volume of TV
Switch off the sound
Sleep timer
SLEEP
SETUP
TV MENU
TV mode - Display menu of TV
DVD mode - Call up initial setup mode
DVD MENU
Display DVD menu
Select channel of TV
Cursor buttons
CH
/
ϳϴϵ϶
ENTER
Enter information in the menu
EXIT
CANCEL
Exit from On-Screen menu
Reset information in the menu
TOP MENU
SEARCH
PLAY
Select title
Fast Forward/Review playback
Playback
SKIP
Skip chapter to forward or reverse direction
Set subtitle
SUBTITLE
STOP
Stop
SLOW
Forward/Reverse- slow motion
PAUSE/STILL
Pause CD sound
Still picture of DVD
PLAY MODE
AUDIO
Select playback mode
Change sound track language
Remove DVD setup menu
Repeat playback between A and B
Change playback angle
RETURN
REPEAT A-B
ANGLE
SCREEN SIZE Display PICTURE SIZE menu
MARKER
JUMP
Index
Locating desired scene
QUICK VIEW
ZOOM
Switch between present/last channel
Zoom
INPUT SELECT Display source selection menu
ATTENTION
If you purchase a universal remote from a local retailer, please contact the remote manufacturer for the correct
programming code.
11
51F0101A_eng.indd 11
3/5/08 5:05:49 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
(continued)
Inserting Batteries
Open the battery compartment
cover in the direction of the arrow.
Install two “AAA” batteries,
paying attention to the
polarity diagram in the battery
compartment.
Replace the compartment cover.
1
2
3
Operation
• Aim the remote control at the remote sensor and press control
buttons to operate.
• Operate the remote control within a 30° angle on either side of
the remote sensor, up to a distance of approximately 15 feet.
Approximately 15 feet
NOTE:
• Do not leave the remote control unit exposed to direct sunlight or in hot or humid places.
• The remote control unit uses infrared beams to transmit signals, so sunlight or fluorescent light on the remote
sensor may shorten operating distance.
• Incorrect use of batteries may cause them to leak or burst. Read the battery warnings and use the batteries
properly.
• Do not mix old and new batteries.
• Remove batteries if the remote control will not be operated for an extended period of time.
Power source
TO USE AC POWER
1.Connect the AC cord plug into this unit’s AC IN jack.
2.Connect the AC cord into an AC outlet.
AC Outlet
Wider Hole
and Blade
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:SHOCK HAZARD-DO NOT OPEN.
A
VIS:RISQUE DE CHOC ELECTRIQUE-NE AS OUVRIR
P
ANT
AC
AC 120V, 60Hz
AC cord (supplied)
NOTE:
• Please make sure to insert the cord securely at both the LCD TV/DVD and the wall outlet.
• The AC Cord has a grounding-type AC line plug. If the supplied AC cord does not match your AC outlet,
contact a qualified electrician, do not defeat the purpose of a grounding plug.
WARNING:
• DO NOT CONNECT THIS UNIT TO THE POWER USING ANY DEVICE OTHER THAN THE SUPPLIED AC
CORD. THIS COULD CAUSE FIRE, ELECTRICAL SHOCK, OR DAMAGE.
• DO NOT USE WITH A VOLTAGE OTHER THAN THE POWER VOLTAGE DISPLAYED. THIS COULD CAUSE
FIRE, ELECTRICAL SHOCK, OR DAMAGE.
CAUTION:
• WHEN THIS UNIT IS NOT USED FOR A LONG TIME, (E.G., AWAY ON A TRIP) IN THE INTEREST OF
SAFETY, BE SURE TO UNPLUG IT FROM THE AC OUTLET.
• DO NOT PLUG/UNPLUG THE PLUG WHEN YOUR HANDS ARE WET. THIS MAY CAUSE ELECTRICAL
SHOCK.
• IF YOU NEED TO REPLACE THE SUPPLIED AC ADAPTER OR AC CORD, THE SPECIFIED ONE IS
RECOMMENDED. CONTACT THE DEALER THAT YOU PURCHASED THE UNIT FROM.
12
51F0101A_eng.indd 12
3/10/08 10:56:11 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Antenna connections
If you are using an indoor or outdoor antenna, follow the instructions below that correspond to your
antenna system. If you are using a Cable TV service, see page 14 for Cable TV connections.
Combination VHF/UHF Antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from the combination
Antenna
VHF/UHF antenna to the antenna jack.
Jack
If your combination VHF/UHF antenna has a 300
ohm twin-lead wire, the use of the 300-75 ohm
matching transformer may be necessary.
75 ohm Coaxial
Cable
Antenna
Jack
300-75 ohm Matching
Transformer
Combination VHF/UHF Antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Connect the UHF 300 ohm twin-lead wire to
the Combiner (not supplied). Connect the VHF
300 ohm twin-lead wire to the 300-75 ohm
Matching Transformer. Attach the Transformer to
300-75 ohm Matching Transformer
VHF 300 ohm
the Combiner, then attach the Combiner to the
Antenna Jack.
Antenna
Jack
UHF 300 ohm
Combiner
Separate VHF/UHF Antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Connect the VHF 75 ohm cable and UHF 300 ohm
twin-leadwiretotheCombiner(notsupplied).Attach
the Combiner to the Antenna Jack.
Antenna
Jack
VHF 75 ohm
UHF 300 ohm
Combiner
IMPORTANT: Go to page 15 to choose the signal and search for channels.
13
51F0101A_eng.indd 13
3/5/08 5:05:50 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable TV connections
This TV has an extended tuning range and can tune most cable channels without using a Cable TV
Converter box. Some cable companies offer “premium pay channels” where the signal is scrambled.
Descrambling these signals for normal viewing requires the use of a descrambler device which is
generally provided by the Cable TV company.
For subscribers to basic Cable TV service
For basic Cable TV service not requiring a Converter/
Descrambler box, connect the 75 ohm Coaxial Cable directly
to the Antenna Jack on the back of the TV.
Antenna
Jack
75 ohm Coaxial
Cable
For subscribers to scrambled Cable TV service
If you subscribe to a Cable TV service which requires the use of a Converter/Descrambler box, connect
the incoming 75 ohm Coaxial Cable to the Converter/Descrambler box. Using another 75 ohm Coaxial
Cable, connect the output jack of the Converter/Descrambler box to the Antenna Jack on the TV. Follow the
connections shown below. Set the TV to the output channel of the Converter/Descrambler box (usually channel
3 or 4) and use the Converter/Descrambler box to select channels.
Incoming
75 ohm
Antenna
Jack
Cable TV
Cable
75 ohm Cable to TV
Converter/
Descrambler
For subscribers to unscrambled Cable TV service with scrambled premium
channels
If you subscribe to a Cable TV service in which basic channels are unscrambled and premium channels require
the use of a Converter/Descrambler box, you may wish to use a signal Splitter and an A/B Switch box (available
from the Cable TV company or an electronics supply store). Follow the connections shown below. With the
switch in the “B” position, you can directly tune any nonscrambled channels on your TV. With the switch in the
“A” position, tune your TV to the output of the Converter/Descrambler box (usually channel 3 or 4) and use the
Converter/Descrambler box to tune scrambled channels.
Incoming
Converter/
75 ohm
Cable TV
Cable
Descrambler
Antenna
Jack
75 ohm Cable to TV
A
A/B Switch
Splitter
B
IMPORTANT: Go to page 15 to choose the signal and search for channels.
14
51F0101A_eng.indd 14
3/5/08 5:05:51 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Press ϳ or ϴ to select “Auto Ch Memory”, then
press ϶ or ENTER.
Setting the on-screen
language
3
Press ϳ or ϴ to select “Signal Type”.
4
5
You can choose from three different languages
(English, French and Spanish) for the on-screen
displays.
Select the language you prefer first, then
proceed with the other menu options.
Press ϵ or ϶ to select “Air” or “Cable”.
Air - VHF/UHF channels
Cable - CABLE TV channels
Auto Ch Memory
Signal Type
Cable
Start
Automatic Search
To turn on the TV, press POWER.
1
(POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.)
: Select
: Adjust
Press TV/DVD to select TV mode.
2
3
Press EXIT/CANCEL to return to the normal
screen.
6
Press SETUP/TV MENU. The TV menu screen
will appear.
CABLE CHART
The chart below is typical of many cable system
channel allocations.
Press ϳ or ϴ to select “Setup”, then press ϶ or
ENTER.
4
Press ϳ or ϴ to select “Language”.
5
Setup
Closed Caption
Language
Video Label
Backlight
>>
English
>>
16
Auto Shut Off
Reset
Off
>>
: Select
: Adjust
NOTE:
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.
NOTE:
• When you press SETUP/TV MENU first time after
purchase this LCD TV, above screen will appear
automatically.
Automatic search
Press ϵ or ϶ to select the desired language:
English, French (Français) or Spanish (Español).
6
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press EXIT/CANCEL to return to the normal
screen.
7
Press ϳ or ϴ to select “Channel”, then press ϶ or
ENTER.
2
NOTE:
Press ϳ or ϴ to select “Auto Ch Memory”, then
press ϶ or ENTER.
3
• If no buttons are pressed for more than about 60
seconds, the menu screen will return to normal
operation automatically.
Press ϳ or ϴ to select “Automatic Search”, then
press ϶ or ENTER.
4
Memorizing channels
Auto Ch Memory
Signal Type
Cable
Stop
Automatic Search
This TV is equipped with a channel memory
feature which allows channels to skip up or down
to the next channel set into memory, skipping
over unwanted channels. Before selecting
channels, they must be programmed into the
TV’s memory. To use this TV with an antenna, set
the Signal Type option to the Air mode. When
shipped from the factory, this menu option is in
the Cable mode.
Analog Channel Found : 0
Digital Channel Found : 0
: Select
ENTER:Cancel
The TV will begin memorizing all the channels
available in your area.
5
• It may take from 15 minutes to 30 minutes to
complete memorizing digital cable channels.
Depending on the reception condition, a bar
display may not advance for several minutes,
please be patient.
Air/Cable selection
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Channel”, then press ϶
or ENTER.
2
15
51F0101A_eng.indd 15
3/5/08 5:05:52 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
Press EXIT/CANCEL to return to the normal
screen.
8
• Memorizing channels is best accomplished during
evening “PRIMETIME” hours, as more stations are
broadcasting digital signals. Memorizing channels
can only be accomplished while a station is
broadcasting a digital signal to set that channel into
memory.
• If you are unsure of the digital channels available
receive a list based on your address or zip code.
• New digital channels may be added to your area
periodically, it is recommended to perform the
“Automatic Search” procedure regularly.
Clear All
All channels are deleted from the channel memory.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Channel”, then press ϶ or
ENTER.
2
Press ϳ or ϴ to select “Add/Delete”, then press ϶
or ENTER.
3
Adding Channel
If you find a new channel unregistered, you can add
the new channel into the channel memory.
Press ϳ or ϴ to select “Clear All”, then press ϶ or
ENTER.
4
Add/Delete
Adding Channel
Add/Delete
Clear All
>>
>>
>>
Tune in the new channel.
1
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
2
: Select
ENTER:Set
Press ϳ or ϴ to select “Channel”, then press ϶ or
ENTER.
3
Press EXIT/CANCEL to return to the normal
screen.
5
Press ϳ or ϴ to select “Add/Delete”, then press ϶
or ENTER.
4
Add/Delete
TV operation
Adding Channel
Add/Delete
Clear All
>>
>>
>>
To turn on the TV, press POWER.
1
(POWER indicator on the front of the unit
changes green. It may take approx. 10 seconds
for a picture to appear on screen.)
: Select
ENTER:Set
Press ϳ or ϴ to select “Adding Channel”, then
press ϶ or ENTER. The new channel will be
added into the channel memory.
5
6
Adjust the volume level by pressing VOL + or – .
2
The volume level will be indicated on the screen
by blue bars. As the volume level increases, so do
the number of bars. If the volume decreases, the
number of blue bars also decreases.
Press EXIT/CANCEL to return to the normal
screen.
Set the Signal Type option to the appropriate
position (see “Air/Cable selection” on page 15).
3
Add/Delete channel
You can select the channel that you want to skip.
Press the Direct Channel Selection (0-9, –)
buttons to select the channel.
(If you press only channel number, channel
selection will be delayed for a few seconds.)
4
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Channel”, then press ϶ or
ENTER.
2
TO SELECT ANALOG CHANNELS
1-9:
Press 1-9 as needed. Example, to
select channel 2, press 2.
Press ϳ or ϴ to select “Add/Delete”, then press
϶ or ENTER.
3
10-99:
Press the 2 digits in order. Example, to
select channel 12, press 1, 2.
100-125: Press the 3 digits in order. Example, to
Press ϳ or ϴ to select “Add/Delete”, then press
϶ or ENTER.
4
select channel 120, press 1, 2, 0.
TO SELECT DIGITAL CHANNELS
Press the first 3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 015-001, press 0, 1,
5, –, 0, 0, 1.
• If a channel is selected with only audio content,
“Audio only” will be displayed on the screen.
• If a channel is selected with a weak digital
signal, “Digital channel signal strength is low”
will be displayed on the screen.
Press ϳ or ϴ to select the channel that you want
to skip.
5
Add/Delete
CH
Signal
Analog
Analog
Digital
Digital
Analog
2
3
Add
Add
3-001
3-002
4
Delete
Add
Delete
: Select
: Adjust
The same program may be available on either
an analog channel or a digital channel.You may
choose to watch either format.
• If a channel is selected to which you have not
subscribed, “Digital channel is encrypted” will
be displayed on the screen.
Press ϵ or ϶ to select “Add” or “Delete”,
whichever function you want to perform.
6
7
Repeat steps 5 - 6 for other channels you want to
add or delete.
16
51F0101A_eng.indd 16
3/5/08 5:05:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
VHF/UHF/CABLE CHANNELS
Sleep Timer
Off
14
Analog Cable
Air
Cable
VHF
2-13
VHF
2-13
Full
480i
UHF
14-69
STD/HRC/IRC
(A) (W)
14-36
• Channel number
• V-Chip rating
• Sleep timer
• Channel label (if preset)
• Signal type
• Picture size
37-59
60-85
86-94
95-99
100-125 (100) (125)
01 (5A)
(AA) (WW)
(AAA) (ZZZ)
(86) (94)
(A-5) (A-1)
• Audio information
(Stereo or SAP)
• Resolution
Press DISPLAY again to clear the call display.
NOTE:
• If a channel with no broadcast is selected, the
sound will automatically be muted.
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.
NOTE:
• After a few seconds, DISPLAY screen will return to
normal TV-operation automatically.
QUICK VIEW
To select the video input source
To view a signal from another device connected to
your LCD TV, such as a VCR player, press INPUT
SELECT, then press ϳ/ϴ or corresponding Number
buttons (0-7), then press ENTER.You can select
TV, Video1, Video2, Component, HDMI1, HDMI2, PC
or DVD depending on which input jacks you used to
connect your devices.
This button allows you to go back to the last channel
selected by pressing QUICK VIEW. Press QUICK VIEW
again to return to the last channel you were watching.
MUTE
Press MUTE to switch off the sound. The TV’s sound
will be silenced and “Mute” will appear on the screen.
The sound can be switched back on by pressing this
button again or the VOL + or –.
Source Selection
0.TV
1.Video1
2.Video2
3.Component
4.HDMI1
5.HDMI2
6.PC
SLEEP
To set the TV to turn off after a preset amount of time,
press SLEEP on the remote control. The clock will
count up 10 minutes for each press of the SLEEP but-
ton (Off, 0h 10m, 0h 20m, ..., 2h 0m). After the sleep
time is programmed, the display will appear briefly
every ten minutes to remind you that the sleep timer
is operating. To confirm the sleep timer setting, press
SLEEP and the remaining time will be displayed for a
few seconds. To cancel the sleep timer, press SLEEP
repeatedly until the display turns to Off.
7.DVD
[0-7]:Select
CH /
Press and release CH
automatically stops at the next channel set into
memory.
For proper operation, before selecting channels, they
should be set into the memory. See “Memorizing
channels” on pages 15 and 16.
/
. The channel
Sleep Timer
0h 10m
DISPLAY
Press DISPLAY to display the current information on
the screen.
When the TV receives a digital signal, the digital
information will appear.
Sleep Timer
Off
62-001 HDTV Moving Picture1
CH-1
Digital Air
English
Labeling channels
No Program Information is available
Channel label appear with the channel number
display each time you turn on the TV, select a
channel, or press DISPLAY.
Full
1080i
You can choose any four characters to identify a
channel.
• Channel number • Station name
• Channel label (if preset) • Broadcast program name
• V-Chip rating
• Sleep timer
• Program guide
• Resolution
• Signal type
• Audio language
• Picture size
To create channel labels
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
When the TV receives a analog signal, the analog
information will appear.
Press ϳ or ϴ to select “Channel”, then press ϶ or
ENTER.
2
17
51F0101A_eng.indd 17
3/5/08 5:05:53 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Label
Press ϳ or ϴ to select “Ch Label”, then press ϶
or ENTER.
The “Ch Label” menu will appear.
3
4
Video1
-
-
-
-
-
Video2
Component
HDMI1
HDMI2
Press ϵ or ϶ to select a channel you want to
label, then press ϴ.
: Select
: Adjust
Ch Label
–
: Uses the default label name
:Video cassette recorder
: DVD video
: Digital TV set-top box
: Satellite box
: Cable box
Channel Number
Ch Label
15-1
>>
VCR
DVD
DTV
SAT
CBL
HD
Label Clear
: Select
: Adjust
: HDMI device (only for HDMI inputs)
Press ϵ or ϶ repeatedly until the character you
want appears in the first space.
5
Press EXIT/CANCEL to return to the normal
screen.
6
Ch Label
Channel Number
Ch Label
15-1
A
Label Clear
>>
Setting the V-Chip
An age limitation can be set to restrict children
from viewing or hearing violent scenes or
pictures that you may choose to exclude. The
restriction applies to “TV Rating” and “Movie
Rating” if this data is transmitted. You may set
this restriction separately. To use the V-Chip
function, you must register a password.
: Select
: Adjust ENTER:Set
The characters rotation as follows:
, () @ / + =
-
-
SPACE
If the character which you desire appears, press
ENTER.
To register a password
Repeat this step to enter the rest of the
characters.
If you would like a blank space in the label name,
you must choose the empty space from the list of
characters.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Lock”, then press ϶ or
ENTER.
2
When you finish inputting the label name, press
EXIT/CANCEL to return to the normal screen.
6
7
Select and enter your password (4 digits) using
Number buttons (0-9), then press ENTER.
3
Lock
Repeat steps 4-5 for other channel.You can
assign a label to each channel.
_
New Password
* * *
To clear a Ch Label
After step 4 above, press ϳ or ϴ to select “Label
Clear”, then press ϶ or ENTER.
[0-9] : Select
ENTER:Set
NOTE:
• The channel labels will be reset after “Automatic
Search” on page 15.
“
” appears instead of the number.
Enter the same password again to confirm, then
press ENTER.
The password is now registered.
4
Labeling video inputs
NOTE:
The Video Label feature allows you to label each
input source for your TV.
• If you forget your password, you can reset it. Turn
the volume all the way down using VOLUME – on
the TV. Continue holding the button and press 0
on the remote control at the same time for about 5
seconds. Enter a new password.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
• To avoid forgetting the password, write it down and
keep in a safe place.
Press ϳ or ϴ to select “Setup”, then press ϶ or
ENTER.
2
Press ϳ or ϴ to select “Video Label”, then press
϶ or ENTER.
3
To set the V-Chip
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select an input which you want to
label.
4
Press ϳ or ϴ to select “Lock” menu, then press
϶ or ENTER.
2
Press ϵ or ϶ to select the desired label for that
input source.
5
Use Number buttons (0-9) to enter your
password, then press ENTER. Then Lock menu
will appear.
3
18
51F0101A_eng.indd 18
3/5/08 5:05:54 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the password
Press ϳ or ϴ to select “V-Chip”, then press
ϵ or ϶ to select “On” .
4
5
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “V-Chip Set”, then press
϶ or ENTER.
The V-Chip Set Menu appears.
Press ϳ or ϴ to select “Lock”, then press ϶ or
ENTER.
2
Press ϳ or ϴ to select which rating will be used,
6
Use Number buttons (0-9) to enter your
password, then press ENTER. The Lock menu
will appear.
3
then press ϶ or ENTER. Each rating below will
appear.
TV Rating
TV Rating
Press ϳ or ϴ to select “Change Password”, then
press ϶ or ENTER.
The Change Password screen will appear.
4
ALL
D
L
S
V
FV
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Enter a new password using Number buttons
(0-9), then press ENTER.
5
: Select
ENTER:Set
You can set the rating using age level and genre.
Enter the same password again to confirm, then
press ENTER.
The password is now registered.
6
Age:
TV-Y
TV-Y7 : 7 years old and above
TV-G : General audience
: All children
Downloading the additional V-Chip rating system
As a supplement to the standard V-Chip rating
system, your television will be able to download an
additional rating system, if such a system becomes
available in the future.
TV-PG : Parental guidance
TV-14 : 14 years old and above
TV-MA : 17 years old and above
Genre:
ALL
D
L
S
V
FV
: All
To download the additional V-Chip rating system
(when available)
: Dialogue
: Language
: Sex
:Violence
: Fantasy Violence
Press SETUP/TV MENU in the digital channel.
1
Press ϳ or ϴ to select “Lock”, then press ϶ or
ENTER.
2
Movie Rating
Movie Rating
Use Number buttons (0-9) to enter your password,
then press ENTER.The Lock menu will apper.
3
G
PG
PG-13
R
Press ϳ or ϴ to select “V-Chip Set (DTV)”, then
press ϶ or ENTER.
4
NC-17
X
: Select
ENTER:Set
If the TV is not storing the additional rating
system, the TV will begin downloading it, which
may take some time to be completed.
5
G
PG
: All ages
: Parental guidance
PG-13 : Parental guidance less than 13 years old
Set your preferred content rating limits for the
additional rating system.
R
: Under 17 years old parental guidance
suggested
6
NC-17 : 17 years old and above
: Adult only
You also need “Update” procedure to update
rating information.
7
X
Press ϳ/ϴ/ϵ/϶ to select the desired rating, then
press ENTER.
7
8
NOTE:
• You can only download the additional V-Chip rating
system when your TV is receiving a digital signal.
• When you download the additional rating system, it
may take some time for the download to occur.
• The V-Chip rating information and system are not
determined or controlled by the TV.
• The standard V-Chip rating system is available
whether your TV is receiving a digital signal or not,
and will block both analog and digital programs. To
set the restriction level using the standard V-Chip
rating system, select V-Chip Set in step 4.
• The downloadable V-Chip rating system is an
evolving technology, and availability, content, and
format may vary.
Press EXIT/CANCEL to return to the normal screen.
V-Chip function is activated now.
To use the TV after the TV is protected.
When a program is received that is blocked by the V-
Chip, press MUTE, then enter your password.
The protection will be temporarily overridden. If the
TV is turned off or the channel is changed, the V-Chip
restriction will be reactivated.
NOTE:
• The V-Chip function is activated only on programs
and input sources that include a rating signal.
• You cannot select this feature if the TV is not
receiving a digital signal for the current station.
19
51F0101A_eng.indd 19
3/5/08 5:05:55 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
live programs. This is because during live programs,
captions are also entered live. These transmissions
do not allow time for editing.
Closed Caption
WHAT IS CLOSED CAPTIONING?
• When Captions are being displayed, on-screen
displays, such as volume and mute may be seen
but may interfere with Closed Captions.
• Some cable systems and copy protection systems
may interfere with the Closed Captioned signal.
• If using an indoor antenna or if TV reception is
very poor, the Closed Caption Decoder may not
appear or may appear with strange characters or
misspelled words. In this case, adjust the antenna
for better reception or use an outdoor antenna.
This television has the capability to decode and
display Closed Captioned television programs. Closed
Captioning will display text on the screen for hearing
impaired viewers or it will translate and display text in
another language.
Captions: This Closed Caption Mode will display
text on the screen in English or another language.
Generally, Closed Captions in English are transmitted
on C1 and Closed Captions in other languages are
transmitted on C2.
Text: The Text Closed Caption Mode will usually fill
1/2 of the screen with a programming schedule or
other information.
CC advanced
When you have selected Custom as the display
method, you can adjust the various setting listed
below as follows:
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
This feature is designed to customize Digital Captions
only.
Press ϳ or ϴ to select “Setup”, then press ϶ or
ENTER.
2
Press SETUP/TV MENU in the digital channel.
The TV menu screen will appear.
1
Press ϳ or ϴ to select “Closed Caption”, then
press ϶ or ENTER.
The Closed Caption menu will appear.
3
Press ϳ or ϴ to select “Setup”, then press ϶ or
ENTER.
2
Press ϵ or ϶ to select “On”.
On: Captions will be displayed on the screen.
Off: Captions will not be displayed on the screen.
4
Press ϳ or ϴ to select “Closed Caption”, then
press ϶ or ENTER.
The Closed Caption menu will appear.
3
Press ϳ or ϴ to select “Digital CC Preset”, then
press ϵ or ϶ to select “Custom”.
Press ϳ or ϴ to select “Analog Caption” or “Digital
Caption”.
5
4
Press ϳ or ϴ to select “CC Advanced”, then
press ϶ or ENTER.
The CC Advanced menu will appear.
When you select “Analog Caption”, you can
choose C1, C2, C3, C4, T1, T2, T3 and T4.
5
When you select “Digital Caption”, you can
choose from CS1, CS2, CS3, CS4, CS5 and CS6.
Press ϳ or ϴ to select the desired item, then
press ϵ or ϶ to change the setting.
6
Press ϵ or ϶ to select the desired Closed
Caption mode for both Digital and Analog
Caption.
6
CC Advanced
Text Size
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Text Type
Text Edge
Text Color
Press ϳ or ϴ to select “CC Priority”, then press
ϵ or ϶ to select “Digital CC” or “Analog CC”.
7
Text Opacity
Background Color
Background Opacity
: Adjust
: Select
NOTE:
You can select from among the following items
and parameters.
• Depending on the broadcast signal, some
Analog Captions will function with a Digital
broadcast signal. This step prevent that two
kind of captions are overlapping.
Text Size:
Text Type:
Auto, Small, Standard, Large
Auto, Style1, Style2, Style3, Style4,
Style5, Style6, Style7
Press EXIT/CANCEL to return to the normal
screen.
8
Text Edge: Auto, None, Raised, Depressed,
Uniform, Left Shadow, Right
Shadow
NOTE:
• If the program or video you selected is not closed-
captioned, no captions will display on-screen.
• If text is not available in your viewing area, a black
rectangle may appear on-screen. If this happens,
set the CC Setting to “Off”.
Text Color: Auto, Black, White, Red, Green,
Blue, Yellow, Magenta, Cyan
Text Opacity: Auto, Solid, Transparent,
Translucent, Flashing
• When selecting Closed Captions, the captioning will
be delayed approx. 10 seconds.
Background Auto, Black, White, Red, Green,
Color:
Background Auto, Solid, Transparent,
Opacity: Translucent, Flashing
Blue, Yellow, Magenta, Cyan
•
If no caption signal is received, no captions will appear,
but the television will remain in the Caption Mode.
• Misspellings or unusual characters may
occasionally appear during Closed Captioning. This
is normal with Closed Captioning, especially with
20
51F0101A_eng.indd 20
3/5/08 5:05:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Press EXIT/CANCEL to return to the normal
screen.
Press ϳ or ϴ to select the item you want to
adjust.
Press ϵ or ϶ to adjust the setting.
7
4
5
NOTE:
• You cannot set both “Text Color” and “Background
Color” as a same color.
• You cannot set both “Text Opacity” and “Background
Opacity” to “Transparent”.
Picture Setting
Brightness
Contrast
Sharpness
Color
25
50
25
25
0
Tint
Color Temperature
Cool
: Select
: Adjust ENTER:Set
Adjusting the picture
preference
Brightness:25
You can select four picture modes—Sports,
Standard, Movie and Memory—as described in
the following table:
After adjusting, press ENTER to return to the
Picture Setting menu. Then continue to adjust the
other items.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
ϵ
϶
Brightness decrease
brightness
increase
brightness
Press ϳ or ϴ to select “Picture”, then press ϶ or
ENTER.
2
Contrast decrease
contrast
increase
contrast
Press ϳ or ϴ to select “Picture Preference”.
3
4
Sharpness makes picture
softer
makes picture
clearer
Press ϵ or ϶ to select a mode you want to adjust.
Color
Tint
be pale color
be brilliant color
Picture
be reddish color be greenish
color
Picture Setting
Picture Preference
Picture Size
Film Mode
>>
Sports
>>
On
PC Setting
>>
DNR
On
After your desired setting, press EXIT/CANCEL
to return to the normal screen.
6
: Select
: Adjust
Mode
Picture Quality
NOTE:
• The Contrast default setting is set to maximum at
the factory.
Sports
Bright and dynamic picture (factory-set)
Standard Standard picture quality (factory-set)
Movie Movie-like picture setting (factory-set)
Selecting the color
temperature
Memory Your personal preferences (set by
you; see “Picture control adjustment”
below).
After your desired setting, press EXIT/CANCEL
to return to the normal screen.
5
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Picture”, then press ϶ or
ENTER.
2
Picture control adjustment
Press ϳ or ϴ to select “Picture Setting”, then
press ϶ or ENTER.
The Picture Setting menu will appear.
3
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Color Temperature”, then
press ϵ or ϶ to change the setting.
4
Press ϳ or ϴ to select “Picture”, then press ϶ or
ENTER.
2
Picture Setting
Press ϳ or ϴ to select “Picture Setting”, then
press ϶ or ENTER.
The Picture Setting menu will appear.
3
Brightness
Contrast
Sharpness
Color
25
50
25
25
0
Tint
Color Temperature
Cool
: Select
: Adjust
Setting
Picture Quality
Bluish
Cool
Standard Neutral
Warm Reddish
21
51F0101A_eng.indd 21
3/5/08 5:05:56 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
The entire picture is uniformly enlarged—it is
stretched the same amount both wider and taller
(retains its original proportion).
Press EXIT/CANCEL to return to the normal
screen.
5
The top and bottom edges of the picture may be
hidden.
Setting the picture size
You can view 480i and 480p format programs in a
variety of picture sizes— Natural, Cinema Wide1,
Cinema Wide2, Cinema Wide3 and Full.
Selecting the picture size
ABCDEFG----------------
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Cinema Wide3 picture size (for letter box
programs with subtitles)
To fill the width of the screen, it is extended
horizontally. However; it is only slightly extended at the
top and the bottom.
Press ϳ or ϴ to select “Picture”, then press ϶ or
ENTER.
2
Press ϳ or ϴ to select “Picture Size”, then press
3
϶ or ENTER to display Picture Size menu. Press
ϳ/ϴ or corresponding Number buttons (0-4)
to select the desired picture size, as described
below.
The top and bottom edges of the picture may be
hidden.
Picture Size
0.Natural
1.Cinema Wide1
2.Cinema Wide2
3.Cinema Wide3
4.Full
ABCDEFG----------------
ABCDEFG--------------------------
[0-4]:Select
Full picture size (for 16:9 source programs)
Full will display the picture at the maximum size.
NOTE:
• Selectable picture sizes may vary depending on the
input source or broadcast signal.
• Picture Size menu also can be displayed by
pressing SCREEN SIZE on the remote control.
Press EXIT/CANCEL to return to the normal
screen.
4
Natural picture size
In some cases, this image will display the size of
standard 4:3 with a black side bar.
NOTE:
• Some High Definition and/or Digital broadcasts may
not allow you to change the picture size.
• In HDMI or COMPONENT mode with a scanning
rate of 720p or 1080i, only the Cinema Wide2 and
Full picture size features are available.
• In PC Mode, only the Natural and Full picture size
features are available. Additionally this feature will
not work when display mode is WXGA.
• In Cinema Wide2 picture size, some of the on
screen display items may be positioned off the
visible portion of the screen.
Cinema Wide1 picture size (for 4:3 format
programs)
To fill the screen, the right and left edges are
extended,
however; the center of the picture remains near its
former ratio.
Film Mode
A smoother motion may be obtained by setting
the Film Mode to “On” when you view a DVD.
The top and bottom edges of the picture may be
hidden.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Picture”, then press ϶ or
ENTER.
2
Press ϳ or ϴ to select “Film Mode”.
Press ϵ or ϶ to select “On” or “Off”.
3
Cinema Wide2 picture size (for letter box
programs)
22
51F0101A_eng.indd 22
3/5/08 5:05:57 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
DNR
Picture Setting
Picture Preference
Picture Size
Film Mode
>>
Sports
>>
DNR (Digital Noise Reduction) can reduce
the roughness of the picture. (This function is
available only for analog broadcast.)
On
PC Setting
>>
DNR
On
: Select
: Adjust
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press EXIT/CANCEL to return to the normal
screen.
4
Press ϳ or ϴ to select “Picture”, then press ϶ or
ENTER.
2
Press ϳ or ϴ to select “DNR”. Press ϵ or ϶ to
select “On” or “Off”.
3
Picture control
adjustment in the PC mode
Picture
Picture Setting
Picture Preference
Picture Size
Film Mode
>>
Sports
>>
You can adjust to optimize the performance of
the TV in the PC mode.
On
PC Setting
>>
DNR
On
: Select
: Adjust
Press INPUT SELECT, then press ϳ/ϴ or
Number button (6) to select the PC mode.
1
Press EXIT/CANCEL to return to the normal
screen.
4
Press SETUP/TV MENU. The TV menu screen
will appear.
2
Press ϳ or ϴ to select “Picture”, then press ϶ or
ENTER.
Sound control
adjustment
3
4
Press ϳ or ϴ to select “PC Setting”, then press ϶
or ENTER.
The PC Setting menu will appear.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
PC Setting
Hor Position
Ver Position
Clock
25
25
0
Press ϳ or ϴ to select “Audio” , then press ϶ or
ENTER.
2
Phase
25
Press ϳ or ϴ to select the item you want to
adjust.
3
: Select
: Adjust ENTER:Set
Audio
Bass
15
15
0
Press ϳ or ϴ to select the desired item you want
to adjust.
5
6
Treble
Balance
MTS
Stereo
No Info.
HDMI
On
Audio Language
HDMI1 Audio
Speakers
Press ϵ or ϶ to adjust the setting.
Hor
Position:
To adjust the horizontal position of
the image on the PC mode.
: Select
: Adjust
Bass:
Press ϵ or ϶ to adjust the bass sound.
Ver
Position:
To adjust the vertical position of the
image on the PC mode.
Treble: Press ϵ or ϶ to adjust the treble sound.
Clock:
To minimize any vertical bars
or stripes visible on the screen
background.
Balance: Press ϵ or ϶ to obtain an equal sound
level from both speakers.
• Press ϳ or ϴ to change the adjusting item.
Phase:
This must be adjusted after the
frequency of the PC mode has
been set to 60Hz to optimize
picture quality (page 38).
After you desired setting, press EXIT/CANCEL to
return to the normal screen.
4
After adjusting, press ENTER to return to the PC
Setting menu. Then continue to adjust the other
items.
Selecting Stereo/Second
Audio Program (SAP)
7
8
Press EXIT/CANCEL to return to the normal
screen.
The multi-channel TV sound (MTS) feature
provides high-fidelity stereo sound. MTS also
can transmit a second audio program (SAP)
containing a second language or other audio
information.
When the TV receives a stereo or SAP broadcast,
the word “Stereo” or “SAP” displays on-screen
every time you press DISPLAY.
NOTE:
• If no buttons are pressed for more than approx. 60
seconds, the Menu-screen will return to normal
Monitor-screen automatically.
• The PC settings are not effective for other input
modes.
23
51F0101A_eng.indd 23
3/5/08 5:05:57 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
or DVI device, you must select HDMI audio input
source from “HDMI” or “DVI”.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
2
3
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Audio”, then press ϶ or
ENTER.
Press ϳ or ϴ to select “Audio”, then press ϶ or
ENTER.
2
Press ϳ or ϴ to select “MTS”, then press ϵ or ϶
to select “Stereo”.
Press ϳ or ϴ to select “HDMI1 Audio”.
Press ϵ or ϶ to select “HDMI” or “DVI”.
3
Audio
Bass
15
15
0
Audio
Treble
Balance
Bass
15
15
0
MTS
Stereo
No Info.
HDMI
On
Treble
Balance
MTS
Audio Language
HDMI1 Audio
Speakers
Stereo
No Info.
HDMI
On
Audio Language
HDMI1 Audio
Speakers
: Select
: Adjust
: Select
: Adjust
Press EXIT/CANCEL to return to the normal
screen.
4
HDMI: When you connect the HDMI device to
the TV, select this setting.
DVI:
When you connect the DVI device to the
TV with analog audio cords, select this
setting.
NOTE:
• Generally you can leave your TV in stereo
mode because the TV automatically outputs
the type of sound being broadcast (stereo or
mono).
• If the stereo sound is noisy, select “Mono” to
reduce the noise.
Press EXIT/CANCEL to return to the normal
screen.
4
Turning off the built-in
speakers
To listen to a second audio program (SAP)
Press ϵ or ϶ to select “SAP” in step 3 above. The
TV speakers will output the second audio program
instead of normal audio.
Use this feature to turn the TV/DVD speakers off
when you connect an audio system (see pages 38).
Selecting the audio
language
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press ϳ or ϴ to select “Audio”, then press ϶ or
ENTER.
2
When two or more audio languages are included
in a digital signal, you can select one of the audio
language. (This function is available only for
digital broadcast.)
Press ϳ or ϴ to select “Speakers”.
Press ϵ or ϶ to select “Off”.
3
Audio
Bass
15
15
0
Press SETUP/TV MENU in the digital channel.
The TV menu screen will appear.
1
Treble
Balance
MTS
Stereo
No Info.
HDMI
On
Audio Language
HDMI1 Audio
Speakers
Press ϳ or ϴ to select “Audio” , then press ϶ or
ENTER.
2
: Select
: Adjust
Press ϳ or ϴ to select “Audio Language”, then
press ϶ or ENTER to display the Audio Language
menu.
Press EXIT/CANCEL to return to the normal
screen.
3
4
To turn on the built-in speakers:
Select “On” in step 3 above.
Press ϳ/ϴ or Number buttons (0-6) to select
your desired language.
4
Adjusting the back
lighting
Audio Language
0. English
1. Language 1
2. Language 2
3. French
4. Language 3
5. Spanish
The Backlight feature adjusts the screen
brightness for improved picture clarity.
6. No Info.
[0-6]: Select
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
1
Press EXIT/CANCEL to return to the normal
screen.
5
Press ϳ or ϴ to select “Setup”, then press ϶ or
ENTER.
2
Selecting the HDMI
audio input source
When you use PC/DVI AUDIO IN jack with HDMI
Press ϳ or ϴ to select “Backlight”.
3
24
51F0101A_eng.indd 24
3/5/08 5:05:58 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Preparation
Closed Caption
Language
Video Label
Backlight
>>
English
>>
16
The following pages describe the setup/
operation in DVD mode.
Auto Shut Off
Reset
Off
>>
: Select
: Adjust
Preparation
Before DVD/CD operation, please make the following
preparations.
Press ϵ or ϶ to adjust the setting.
4
5
Press EXIT/CANCEL to return to the normal
screen.
Insert the AC cord plug into a standard 120V
60Hz polarized AC outlet.
1
• If the AC cord plug is plugged in for the first
time, wait for about 5 seconds before pressing
POWER.
Setting the Auto Shut Off
If the Auto Shut Off feature is On, a station being
viewed stops broadcasting and the TV is not
operated, the TV will automatically shut itself off
after 15 minutes.
NOTE:
• When connecting to other equipment, unplug
the unit from the AC outlet.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
Press ϳ or ϴ to select “Setup”, then press ϶ or
ENTER.
Press ϳ or ϴ to select “Auto Shut Off”.
Press ϵ or ϶ to select “On” or “Off”.
Setup
1
2
3
Press POWER on the unit or on the remote
control to turn on the unit. The POWER indicator
will change to green.
• Each time you turn the unit ON, the TV/DVD
starts from the TV mode.
2
• When using an amplifier, switch on the
amplifier.
Closed Caption
Language
Video Label
Backlight
>>
English
>>
Press TV/DVD to select DVD mode.
The DVD startup screen will appear on the
screen.
3
16
Auto Shut Off
Reset
Off
>>
: Select
: Adjust
Press EXIT/CANCEL to return to the normal
screen.
4
Resetting your settings
The Reset function returns your settings to the
factory settings.
NOTE:
• If the unit does not operate properly:
Static electricity, etc., may affect the player’s
operation. Disconnect the AC power cord once,
then connect it again.
Press SETUP/TV MENU in the TV mode. The TV
menu screen will appear.
Press ϳ or ϴ to select “Setup” , then press ϶ or
ENTER.
1
2
3
Press ϳ or ϴ to select “Reset”.
Status display of disc
Setup
Press DISPLAY. The status display of the disc will
appear on the screen.
Closed Caption
Language
Video Label
Backlight
>>
English
>>
16
ELAPSED
TIME
TOTAL
TIME
Auto Shut Off
Reset
Off
DISC OPERATION
>>
: Select
ENTER:Set
TITLE NO.
DVD
00:15:25 01:41:39
Chapter 2/24
1/2 Eng
Press ϶ or ENTER to return your settings to the
factory settings.
“Reset” will appear on the screen approx. 3
seconds, then it returns to the normal screen.
CHAPTER
NO.
4
5
Title 1/3
1/1 Eng Dolby Digital
1/1
Audio
Picture
ANGLE NO.
AUDIO LANGUAGE A KIND OF AUDIO
SUBTITLE LANGUAGE
Bass
15
15
0
Picture Setting
Picture Preference
Picture Size
Film Mode
>>
Treble
Sports
>>
Balance
MTS
Stereo
No Info.
HDMI
On
On
To make the status display screen disappear, press
DISPLAY again.
Audio Language
HDMI1 Audio
Speakers
PC Setting
>>
DNR
On
: Select
ENTER:Set
: Select
: Adjust
NOTE:
• “Picture Size” in Picture menu cannot be reset by
this function.
• “MTS”, “Audio Language”, “HDMI1 Audio” and
“Speakers” in Audio menu cannot be reset by this
function.
25
51F0101A_eng.indd 25
3/7/08 4:29:20 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback procedure
Special playback
Fast Forward Playback
Press TV/DVD to select DVD mode.
1
2
Press SEARCH
Each press of SEARCH
during normal playback.
will increase the speed of
(x 4), (x 8), (x
Place the disc in the
the search
15).
(x 2),
(x 4),
disc slot with the label
side facing forward. (If
the disc has a label.)
Hold the disc without
touching either of its
surfaces, align it with
the guides, and place it
in position.
(CD:
(x 2),
(x 8),
(x 20))
• To resume normal playback, press PLAY.
Review Playback
Press SEARCH during normal playback.
Each press of SEARCH
will increase the speed
(x 4), (x 8),
of the search
(x 15).
(x 2),
(x 4),
On the screen, “ ” changes to “Reading” and
then playback will commence.
• A menu screen may appear on the TV screen,
if the disc has a menu feature. In this case,
press ϳ, ϴ, ϵ, ϶ or ENTER to operate a menu
feature.
3
(CD:
(x 2),
(x 8),
(x 20))
• To resume normal playback, press PLAY.
Still Playback
Press PAUSE/STILL during normal playback to pause
playback.
Reading
• To resume normal playback, press PLAY.
Press STOP to end playback.
4
• The unit memorizes the stopped point,
depending on the disc. “ ” appears on the
screen. Press PLAY to resume playback (from
the scene point).
Frame Advance
Press PAUSE/STILL during still playback.
One frame is advanced each time you press PAUSE/
STILL.
• If you press STOP again (“ ” appears on the
screen) or unload the disc, the unit will clear the
stopped point.
• To resume normal playback, press PLAY.
Slow-motion Playback
Press (EJECT).
Remove the disc and then press POWER.
The unit turns off.
When you eject the disc, you may hear
mechanism noise, but it is not malfunction.
5
Press SLOW Reverse or SLOW Forward
during normal playback or still playback.
Each press of SLOW will change the speed of the
slow x1/2, x1/4, x1/6, x1/7.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE/STILL.
NOTE:
• If a non-compatible disc is loaded, “Incorrect Disc”,
“Region Code Error” or “Parental Error” will appear
on the TV screen according to the type of loaded
disc. If these appear, check your disc again (see
pages 8 and 33~34).
Locating a chapter or track
Press SKIP
Forward or SKIP
Reverse during
playback to locate a chapter that you want to watch.
Each time you press the button, a chapter or track is
skipped.
• Some discs may take a minute or so to start
playback.
• If an 8 cm disc is placed into the disc slot and
picture playback or menu display does not begin
automatically, press PLAY.
NOTE:
• The unit is capable of holding a still video image or
On screen display image on your television screen
indefinitely. If you leave the still video image or On
screen display image displayed on your TV for
an extended period of time, you risk permanent
damage to your television screen.
• A “Prohibition” symbol “ ” may appear at the upper
right of the screen. This symbol means either the
feature you tried is not available on the disc, or the
unit cannot access the feature at this time. This
does not indicate a problem with the unit.
• If you place a single-faced disc label backwards (i.e.
the wrong way) “Reading” will appear in the display
and then “Incorrect Disc” will be displayed.
• Some playback operations of DVDs may be
intentionally fixed by software producers. Since
this unit plays DVDs according to the disc content
recorded, some playback features may not be
available. Also refer to the instructions supplied with
the DVDs.
• There may be a slight delay between when you
press the button and the function activating.
26
51F0101A_eng.indd 26
3/5/08 5:05:59 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
A file browser screen will appear on the TV
3
screen.
MP3/WMA/JPEG and
Audio CD playback
Operation status
File number Elapsed time Selected file name
1/15 00:00:00
This player can play back MP3/WMA/JPEG-data
which has been recorded on CD-R or CD-RW.
To produce MP3/WMA/JPEG-data, you need a
Windows-PC with CD-ROM drive and MP3/WMA/
JPEG-encoding software (not supplied).
/MP3-5.MP3
MP3-5
Select Files
Repeat :Off
MP3-6
Tool kit
window
Mode
:Off
WMA-11
WMA-12
Picture-1
Picture-2
Picture-3
Picture-4
File list
The Apple-HFS-System cannot be played.
Music Playing
MP3/WMA/JPEG CD information
Limitations on MP3/WMA/JPEG CD playback
• MP3/WMA/JPEG CD is the disc that is
standardized by ISO9660, its file name must
include 3-digit extension letters, “mp3”, “wma”, “jpg”.
• The directory and file names of MP3/WMA/JPEG
CD must correspond to ISO standardized files.
• This unit can read 2000 files per disc. If one
directory has more than 2000 files, it reads up to
2000 files, the remaining files will be omitted.
• MP3/WMA CDs cannot be used for playback for the
purpose of recording.
Cursor
Preview window
File type
: Indicates Music file (Audio CD/MP3/WMA)
: Indicates Picture file (JPEG)
• In case the current directory includes 9 files or
more, press ϳ or ϴ to scroll in the file list.
• To see contents in folder, select the folder and
then press ENTER. To return to the parent
directory, select “ Go Up ...” then press
ENTER.
• If the CD has both audio tracks and MP3/WMA/
JPEG files, only audio tracks are played.
• It may take more than one minute for this unit
to read MP3/WMA/JPEG files depending on its
structure.
• Music recorded by “Joliet Recording Specification”
can be played back.
• The music files recorded by “Hierarchical File
System” (HFS) cannot be played.
• The unit can play back baseline and progressive
JPEG files.
• MP3 or WMA files on the KODAK Picture CD are
not recognized on this unit.
• In case of a CD containing a mixture of MP3,
WMA and JPEG files, the files are played back
by selecting them from the file browser.
Press ϳ or ϴ to select the desired file.
4
When PLAY is pressed after displaying file
browser displayed, playback begins automatically
starting from the first file.
In this case, if the first file is an MP3/WMA file,
only MP3/WMA files are played back in order. If
the first file is a JPEG file, the first JPEG file is
played back. If there is no file at a root directory,
playback does not begin automatically.
Limitations on display
/MP3-2.MP3
• The maximum number for display is 15 characters.
Long file names will be condensed.
• Available letters for display are the following:
capital or lowercase letters A through Z, numbers 0
through 9, and _ (under score).
Select Files
Folder-1
Folder-2
MP3-1
Repeat :Off
Mode
:Off
MP3-2
MP3-3
WMA-1
WMA-2
WMA-3
JPEG Preview
• Other letters than those above are replaced by a
hyphen.
Press ENTER.
The selected file starts playing back.
5
6
Notes on MP3/WMA/JPEG files
To play back MP3/WMA/JPEG CD in the recorded
order,
1.Use MP3/WMA/JPEG software that records data
alphabetically or numerically.
2.Name each file including a two-digit or three-digit
number (e.g. “01” “02” or “001” “002”).
3.Refrain from making too many sub-folders.
Press STOP to end playback.
• The unit records the stopped point. “
appears on the screen. Press PLAY to resume
playback (from the scene point).
• If you press STOP again or unload the disc, the
unit will clear the stopped point.
”
CAUTION:
NOTE:
• Some MP3/WMA/JPEG CDs cannot be played
back depending on the recording conditions.
• The CD-R/RW that has no music data or non-MP3/
WMA/JPEG files can not be played back.
• During MP3/WMA/JPEG-Playback, you cannot
use JUMP and A-B Repeat functions.
• You can use Program playback, Repeat (Track
or All) and Random functions for MP3/WMA/
JPEG and Audio CD Playback (see pages 28
and 29).
MP3/WMA CD and Audio CD playback:
Load a MP3/WMA/JPEG CD or an Audio CD in
the disc slot.
1
“Reading” will appear on the TV screen. Reading
time will depend on the number of files on the
disc.
2
27
51F0101A_eng.indd 27
3/5/08 5:06:00 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
JPEG playback:
TV Screen
Display
: 16:9
: On
In the file browser, pressϳ/ϴ to select the desired
JPEG file.
1
Picture Mode : Auto
Off
JPEG Interval
To display a thumbnail list, press DVD MENU.
Press ϳ/ϴ/ϵ/϶ to select the desired file.
(To return to the file browser, press TOP MENU.)
5 Seconds
10 Seconds
15 Seconds
/Picture-01.JPG
Off:
Plays back one file at a time.
Select Files
Picture-01
Picture-02
Picture-03
Picture-04
Picture-05
Picture-06
Picture-07
Picture-08
Repeat :Off
Mode
:Off
5 Seconds:
Plays back images in the form of a slide show at 5
second intervals.
W: 2048 H: 1536
10 Seconds:
Plays back images in the form of a slide show at
10 second intervals.
Press ENTER or PLAY.
The selected picture appears on the TV screen.
2
3
15 Seconds:
Plays back images in the form of a slide show in
15 second intervals.
Rotating an image
You can rotate an image by 90 degrees.
Press ANGLE during playback of the image.
“
Zooming an image
”, “ ”, “
” or “ ” appears on the screen.
Press SETUP/TV MENU to remove the menu
screen.
4
Zoom function also can be used in viewing JPEG
files.
Press ZOOM (See “Zooming” on page 29).
Program playback (CD)
Press STOP to end playback.
The file browser appears on the TV screen.
If you want to watch the other file, repeat steps
1-2.
You can arrange the order of tracks on the disc.
In the file browser, press ϳ/ϴ/ϵ/϶ to select “Edit
Mode”, then press ENTER.
1
Select Files
The file type to make it display in the file browser can
be chosen.
When “Edit Mode” is black color, you can mark
the files which you want to add into Program list.
Press ϵ/϶ to select “Select Files” at right column
in the file browser.
1
Folder-1
Repeat :Off
Folder-2
Mode
:Off
• Press ENTER, then press ϳ/ϴ to select file
type from the list (Music or Picture).
MP3-1
MP3-2
MP3-3
WMA-1
WMA-2
WMA-3
Edit Mode
JPEG Preview
Press ENTER to add/remove check mark.
Checked file type will be displayed in the file
browser.
2
Press ϳ/ϴ/ϵ/϶ to select the file you want to add
into the program list.
2
3
Press RETURN to save the setting.
3
Press ENTER. Selected file was marked.
Repeat this procedure to select the other files.
Setting the JPEG
interval
/MP3-1.MP3
Folder-1
Repeat :Off
Folder-2
Mode
:Off
You can continuously play back all JPEG files
automatically.
MP3-1
MP3-2
MP3-3
WMA-1
WMA-2
WMA-3
Edit Mode
JPEG Preview
Press SETUP/TV MENU in the stop mode.
option, then press
1
Press ϳ or ϴ to select
ϵ/϶ or ENTER.
Press ϳ/ϴ/ϵ/϶ to select “Add To Program”.
Then press ENTER. All marked files are added
into the program list.
Press ϳ or ϴ to select “JPEG Interval”, then press
϶ or ENTER.
2
3
Press ϳ or ϴ to select your desired time, then
press ENTER.
When you finish storing the files you want into the
Program list, select “Edit Mode” again and press
ENTER to release edit mode.
28
51F0101A_eng.indd 28
3/5/08 5:06:01 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Random playback (CD)
Folder-1
Folder-2
MP3-1
Edit Mode
Program View
Add To Program
In the file browser, press ϳ/ϴ/ϵ/϶ to select
“Mode”.
1
MP3-2
MP3-3
WMA-1
WMA-2
WMA-3
JPEG Preview
Press ENTER to select “Random”.
2
Folder-1
Folder-2
MP3-1
Select Files
Press ϳ/ϴ to select “Program View”, then
press ENTER. Program View shows only the
programmed files that you have added in Step 2.
4
5
Repeat :Off
Mode
:Random
MP3-2
MP3-3
WMA-1
WMA-2
WMA-3
JPEG Preview
Folder-1
Folder-2
MP3-1
MP3-1
MP3-2
MP3-3
WMA-3
Edit Mode
Program View
Add To Program
Edit Mode
Browser View
Clear Program
MP3-2
MP3-3
Press PLAY.
The Random playback will start.
3
WMA-1
WMA-2
WMA-3
JPEG Preview
JPEG Preview
To resume normal playback, select Mode : “Off”
in step 2.
Browser View
Program View
In the Program View, press PLAY. The files start
to playback in programmed order that were
added by you.
Zooming
This unit will allow you to zoom in on the
frame image.You can then make selections by
switching the position of the frame.
To remove file from program list in stop mode
In the Edit Mode, switch to Program View. Select the
files you want to remove, then press ENTER. Select
“Clear Program” and press ENTER. Marked file is
removed from program list.
Press ZOOM during playback.
The center part of the image will be zoomed in.
Each press of ZOOM will change the ZOOM
1
NOTE:
• The program is cancelled when you eject the disc
or turn the power off.
magnification
(x 2.0).
1 (x 1.3),
2 (x 1.5) and
3
Press ϳ/ϴ/ϵ/϶ to view a different part of the
frame.
You may move the frame from the center position
UP, DOWN, LEFT or RIGHT.
2
3
Repeat playback (CD)
In the file browser, press ϳ/ϴ/ϵ/϶ to select
“Repeat”.
1
In the zoom mode press ZOOM repeatedly to
Press ENTER repeatedly to select “Track” or “All”.
return to a 1:1 view (
Off).
2
NOTE:
• You can select the Pause, Slow or Search playback
in the zoom mode.
• Some discs may not respond to zoom feature.
Folder-1
Folder-2
MP3-1
Select Files
Repeat :Track
Mode
:Off
MP3-2
MP3-3
WMA-1
WMA-2
WMA-3
JPEG Preview
Locating desired scene
Press PLAY.
The unit automatically starts repeat playback
after finishing the current track.
Use the title, chapter and time recorded on the
disc to locate the desired point to play back.
3
Press JUMP during playback or stop mode.
1
To resume normal playback, select Repeat : “Off”
in step 2.
Jump
Title
NOTE:
Chapter
Time
• The repeat or random function is canceled when
you eject the disc or turn the power off.
• The track repeat function is canceled when SKIP
Press ϳ or ϴ to select the “Title”, “Chapter” or
“Time”.
2
or
is pressed.
• In case of Audio CD, the function of A-B Repeat
also can be used (See “A-B Repeat playback” on
page 30).
Press Number buttons (0–9) to input the
number.
• If you input a wrong number, press EXIT/
CANCEL.
• Refer to the package supplied with the disc to
3
check the numbers.
29
51F0101A_eng.indd 29
3/7/08 4:29:23 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
• During the A-B Repeat Playback the ANGLE
feature will not operate.
• You may not be able to set A-B Repeat, depending
on the scenes of the DVD.
• A-B Repeat does not work with an interactive DVD,
MP3/WMA/JPEG-CD.
Press ENTER.
• Playback starts.
• When you change the title, playback starts from
Chapter 1 of the selected title.
• Some discs may not work in the above
operation.
4
Marking desired scenes
Repeat playback
The TV/DVD stores the points that you want to
watch again.You can resume playback from that
scene.
Title, Chapter Playback:
Press PLAY MODE during playback or stop
mode.
1
Marking the scenes:
Press MARKER during playback.
Press ENTER repeatedly to select “Chapter” or
“Title”.
1
2
Select the blank Marker using ϳ or ϴ, then press
ENTER at the desired scene.
2
The unit automatically starts repeat playback
after finishing the current title or chapter.
• If you set the repeat mode during stop mode,
press PLAY to start Repeat playback.
Marker 1
Marker 2
Marker 3
00 27 54
Play Mode
Repeat
: Off
• Up to 3 scenes can be selected.
• Repeat this procedure to set the other 2
scenes.
Press PLAY MODE again to make the screen
disappear.
3
• In stop mode, press PLAY to start Repeat
playback.
Press MARKER to remove this display.
3
• To resume normal playback, select Repeat
“Off” in step 2.
Returning to the scenes:
Press MARKER during playback or stop mode.
1
2
A-B Repeat Playback:
A-B repeat playback allows you to repeat material
between two selected points.
Press ϳ or ϴ to select the Marker 1-3.
Marker 1
Marker 2
Marker 3
00 27 54
01 16 25
02 08 31
Press REPEAT A-B during playback.
The start point is selected.
1
A
Press ENTER.
Playback starts from the marked scene.
3
To cancel the mark:
Press MARKER during playback or stop mode.
1
2
3
Press REPEAT A-B again.
2
The end point is selected. Playback starts at the
point that you selected. Playback stops at the end
point, returns to Point A automatically, then starts
again.
Press ϳ or ϴ to select the Marker 1-3.
Press EXIT/CANCEL.
Press MARKER to remove this display.
A
B
NOTE:
• The marking is canceled when you eject the disc or
turn the power off.
• Some subtitles recorded around the marker may fail
to appear. [DVD]
Changing soundtrack
language
To resume normal playback press REPEAT A-B
again.
3
“
” appears on the screen.
Off
You can select the language when you play a
multilingual disc.
NOTE:
• Some discs may not work with the repeat operation.
• In A-B repeat mode, subtitles near point A or B may
not appear.
30
51F0101A_eng.indd 30
3/7/08 4:29:24 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Press AUDIO during playback.
1
2
Changing angles
The current soundtrack language will appear.
When playing back a disc recorded with multi-
angle facility, you can change the view angle.
1/2 Eng Dolby Digital
Press ANGLE during playback.
1
The current angle will appear.
1/2
Press AUDIO repeatedly until the desired
language is selected.
The on-screen display will disappear after a few
seconds.
NOTE:
• If the desired language is not heard after pressing
AUDIO several times, the language is not recorded
on the disc.
Press ANGLE repeatedly until the desired angle
is selected.
2
• Changing soundtrack language is cancelled when
you eject the disc.
The initial default language or available language
will be heard if the disc is played back again.
NOTE:
• Depending on the DVD, you may not be able to
change the angles even if multi-angles are recorded
on the DVD.
Subtitles
Title selection
Turning the subtitles on and off
When playing back a disc recorded with subtitles, you
can turn the subtitles on or off.
Two or more titles are recorded on some discs.
If the title menu is recorded on the disc, you can
select the desired title.
Press SUBTITLE during playback until “Off” appears.
Press TOP MENU during playback.
Title menu appears on the screen.
1
Off
Press ϳ/ϴ or ϵ/϶ to select the desired title.
2
Press ENTER or PLAY.
The playback of the selected title will start.
3
Changing the subtitle language
You can select the language when playing back a disc
recorded with multilingual subtitles.
NOTE:
• Depending on the DVD, you may not be able to
select the title. Depending on the DVD, a “title
menu” may simply be called a “menu” or “title” in the
instructions supplied with the disc.
Press SUBTITLE repeatedly during playback
until your desired language appears.
1
1/5 Eng
DVD menu
Some DVDs allow you to select the disc contents
using the menu.
When you playback these DVDs, you can select
the subtitle language and soundtrack language,
etc. using the DVD menu.
The on-screen display will disappear after a few
seconds.
2
Press DVD MENU during playback.
The DVD menu appears on the screen.
• Press DVD MENU again to resume playback at
the scene when you pressed DVD MENU.
1
NOTE:
• Changing subtitle language is cancelled when you
eject the disc.
• Some functions may not work on some DVDs.You
may not be able to turn subtitles on or off or change
subtitles. While playing the DVD, the subtitle may
change when:
Press ϳ/ϴ or ϵ/϶ to select the desired item.
2
3
Press ENTER.
The menu continues to another screen. Repeat
steps 2 and 3 to set additional items if any.
- you eject the disc.
- you change the title.
• In some cases, the subtitle language is not changed
to the selected one immediately.
31
51F0101A_eng.indd 31
3/5/08 5:06:05 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
You have the following screen sizes to choose
from:
Setting the language
4:3
Letterbox
You can select the language of “Menu”, “Subtitle”
and “Audio” if more than one languages are
recorded onto the disc.
When playing back a wide screen DVD disc, it
displays the wide picture with black bands at the
top and bottom of screen.
4:3
Panscan
Press SETUP/TV MENU in the stop mode.
Press ϳ or ϴ to select
or ENTER.
1
It displays the wide picture on the whole screen
with left and right edges automatically cut off.
option, then press ϵ/϶
16:9 Wide
A wide screen picture is displayed full size.
Press ϳ or ϴ to select desired option, then press
϶ or ENTER.
2
3
Press SETUP/TV MENU to remove the menu
screen.
4
Press ϳ or ϴ to select your desired language
(e.g. English), then press ENTER.
NOTE:
Menu
English
Francais
Espanol
Other
• It is not always possible for the DVD disc to display
the picture as per your preferred picture setting - for
example, if you select “4:3 Panscan”, the disc may
not offer this option. In this case the picture would
display the format the disc is capable of playing
back.
Subtitle
Audio
English, Francais, Espanol :
The selected language will be heard or seen.
Setting on screen
display
Other:
Other language can be selected (see the
“Language code list” on page 35).
On screen display can be switched on or off
when you press the any button.
Original (Audio):
The unit will select the first priority language of
each disc.
Press SETUP/TV MENU in the stop mode or No
Disc.
1
Press ϳ or ϴ to select
ϵ/϶ or ENTER.
option, then press
Off (Subtitle):
Subtitles do not appear.
Press ϳ or ϴ to select “Display”, then press ϶ or
ENTER.
2
3
Press SETUP/TV MENU to remove the menu
screen.
4
Press ϳ or ϴ to select “On” or “Off”, then press
ENTER.
NOTE:
• If the selected language is not recorded on the disc,
the first priority language is selected.
TV Screen
Display
: 16:9
Off
On
Picture Mode
Setting the aspect ratio
of TV screen
JPEG Interval : Off
You can select the aspect ratio of the picture.
On: On screen displays appear when you press
the buttons (factory setting).
Off: On screen displays do not appear when you
press any buttons except SUBTITLE, PLAY
MODE, MARKER, DISPLAY, AUDIO and
JUMP.
Press SETUP/TV MENU in the stop mode or No
Disc.
1
Press ϳ or ϴ to select
ϵ/϶ or ENTER.
option, then press
Press ϳ or ϴ to select “TV Screen”, then press ϶
or ENTER.
2
3
Press SETUP/TV MENU to remove the menu
screen.
4
Press ϳ or ϴ to select your desired screen type,
then press ENTER.
TV Screen
Display
4:3
Setting the picture mode
4:3
16:9
Picture Mode
There are two types of source content in pictures
recorded in DVD video discs: film content
(pictures recorded from films at 24 frames
per second) and video content (video signals
recorded at 30 frames per second). Make this
selection according to the type of content being
viewed.
JPEG Interval : Off
32
51F0101A_eng.indd 32
3/5/08 5:06:05 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Press SETUP/TV MENU in the stop mode or No
Disc.
1
Digital Out
Press ϳ or ϴ to select
or ENTER.
option, then press ϵ/϶
You can select the digital output sound format
corresponding to your system connection.
Press ϳ or ϴ to select “Picture Mode”, then press
϶ or ENTER.
2
3
Press SETUP/TV MENU in the stop mode or No
Disc.
1
Press ϳ or ϴ to select your desired picture mode,
then press ENTER.
Press ϳ or ϴ to select
ϵ/϶ or ENTER.
option, then press
Press ϳ or ϴ to select “Digital Out”, then press ϶
or ENTER.
2
3
TV Screen
Display
: 16:9
: On
Auto
Picture Mode
JPEG Interval
Press ϳ or ϴ to select “Off”, “PCM” or “Bitstream”,
then press ENTER.
Film
Video
Night Mode
Digital Out
: Off
Off
PCM
Bitstream
Auto:
Select this position normally.
The DVD player automatically detects source
content, film or video, of playback source.
Film:
Suitable for playback of film content pictures.
Off:
There is no sound output from
DIGITAL AUDIO OUT jack.
Change Dolby Digital to PCM for the
output. Select when connected to a 2
channel digital stereo amplifier.
Video:
Suitable for playback of video content pictures.
PCM:
Press SETUP/TV MENU to remove the menu
screen.
4
Bitstream: Disc audio bitstream data will be
output.
NOTE:
• Depending on the disc, pictures may be cut off or
doubled. In this case, select “Video”.
Press SETUP/TV MENU to remove the menu
screen.
4
NOTE:
• This function works only during playback of Dolby
Digital recorded discs.
Night Mode
• The level of Dynamic Range Reduction may differ
depending on DVD video disc.
• Even if you select “Bitstream”, MPEG audio will be
output in PCM format.
Night Mode enables you to control the dynamic
range so as to achieve a suitable sound for your
equipment.
Press SETUP/TV MENU in the stop mode or No
Disc.
1
Parental control
Press ϳ or ϴ to select
ϵ/϶ or ENTER.
option, then press
Some discs are specified not suitable for
children. Such discs can be limited not to play
back with the unit.
Press ϳ or ϴ to select “Night Mode”, then press
϶ or ENTER.
2
3
Press ϳ or ϴ to select “On” or “Off”, then press
ENTER.
Password and setting:
On : Loud sounds such as explosions are toned
down slightly when played.
Off : The unit will play the disc as recorded.
Press SETUP/TV MENU in the stop mode or No
Disc.
1
Press ϳ or ϴ to select
ϵ/϶ or ENTER.
option, then press
Night Mode
Digital Out
Off
On
Press ϳ or ϴ to select “Parental”, then press ϶ or
ENTER.
“Enter Password” screen will appear.
2
3
Press “0000” using Number buttons (0-9). (This
is pre-setting password of this unit). Then press
ENTER.
• If you input a wrong number, press EXIT/
CANCEL.
Press SETUP/TV MENU to remove the menu
screen.
4
33
51F0101A_eng.indd 33
3/5/08 5:06:06 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Parental
: Off
Parental
: Off
PasswEnter e
Password
Password
: Change
Enter New Password
The parental level list will appear. Press ϳ or ϴ to
select the level 1 to level 8. The limitation will be
more severe as the level number is lowered. Then
press ENTER.
Press ENTER.
Now your new password has been set.
Be sure to remember this number!
4
5
NOTE:
1
Parental
• If you forget your password it can be reset. With no
disc in the player and in DVD mode, press STOP on
the unit. Continue holding the button and press 7
on the remote control at the same time. “Password
Clear” appears on the screen. Now the password
has been return to the initial value (0000).
2
Password
3
4
5
6
7
8
Off
Temporary disabling of
rating level by DVD disc
• Level Off : The parental control setting does
not function.
• Level 8
• Level 1
:
:
Virtually all DVD software can be
played back.
DVD software for adults cannot be
played back.
Some pre-recorded DVD discs may attempt to
temporarily cancel the rating level that you have
set.You will be given the option to allow or not
allow the override.
• Select from level 1 to level 8. The limitation will
be more severe as the level number decreases.
Load a DVD disc (see page 26).
1
2
Press SETUP/TV MENU to remove the menu
screen.
5
If the DVD disc has been designed to temporarily
cancel the Rating level, the screen which follows
the “Reading” screen will change, depending
on which disc is played. If you select “YES” with
ENTER key, password input screen will then
appear.
NOTE:
• If each setup (P.32~34) has been completed,
the unit will use these settings during DVD
playback.
Each setup will be retained in memory.
• Depending on the discs, the unit may not be able to
limit playback.
• Some discs may not be encoded with specific rating
level information though its disc jacket says “adult”.
For those discs, the age restriction will not work.
• After the rating is locked, the setting cannot be
changed unless you enter the correct password.
Enter the password with Number buttons (0-9).
Then press ENTER.
• If you interrupt the entering, press RETURN.
3
Enter Password
Setting the new password:
Press SETUP/TV MENU in the stop mode or No
Disc.
1
Playback will commence if the entered password
was correct.
4
Press ϳ or ϴ to select
ϵ/϶ or ENTER.
option, then press
NOTE:
Press ϳ or ϴ to select “Password”, then press ϶
or ENTER.
“Enter Current Password” screen will appear.
2
3
• This temporary cancellation of the rating level will
be kept until the disc is ejected.
When the disc is ejected, the original rating level will
be set again automatically.
Press Number buttons (0-9) to enter the
password you have stored.
• If you input a wrong number, press EXIT/
CANCEL.
Then press ENTER. “Enter New Password”
screen will appear. Press Number buttons (0–9)
to input the new password.
4
34
51F0101A_eng.indd 34
3/7/08 4:29:25 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Language code list
Enter the appropriate code number for the initial settings “Menu”, “Subtitle” and/or “Audio” (see page 32).
Language Name
Abkhazian
Afar
Code Language Name
1112 Fiji
Code Language Name
1620 Lingala
Code Language Name
2224 Singhalese
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2322 Sundanese
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
Code
2919
2921
2922
2925
1529
2931
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
3219
3225
1335
3325
3418
2019
3525
3631
1111 Finnish
1116 French
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
Afrikaans
Albanian
Amharic
Arabic
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
2111 Malayalam
1415 Maltese
1522 Maori
Armenian
Assamese
Aymara
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
2122 Marathi
Azerbaijani
Bashkir
1724 Moldavian
1731 Mongolian
1811 Nauru
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla
Bhutani
1224 Hebrew
1436 Hindi
1933 Nepali
2415 Telugu
2425 Thai
1819 Norwegian
1831 Oriya
Bihari
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
2629 Tonga
Breton
1929 Panjabi
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
1924 Pashto, Pushto
1911 Persian
1611 Turkish
2622 Turkmen
2630 Twi
1711 Polish
2123 Italian
1930 Portuguese
2011 Quechua
2033 Rhaeto-Romance
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
1311 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2731 Ukrainian
2823 Urdu
Chinese
Corsican
Croatian
Czech
2825 Uzbek
2831 Vietnamese
2923 Volapük
2911 Welsh
1714 Wolof
Danish
Dutch
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
English
2928 Xhosa
2918 Yiddish
2924 Yoruba
2914 Zulu
Esperanto
Estonian
Faroese
2225 Serbo-Croatian
2211 Shona
1625 Latvian, Lettish
2232 Sindhi
35
51F0101A_eng.indd 35
3/5/08 5:06:08 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections to other equipment
The exact arrangement you use to interconnect various video and audio components to this unit is dependent
on the model and features of each component. Check the Owner’s Manual provided with each component for
the location of video and audio inputs and outputs.
To connect the LCD TV/DVD to a VCR
Rear of the unit
To LINE 2 VIDEO/AUDIO IN
VCR
To Audio/Video OUT
or
Audio/Video cord
(not supplied)
To LINE 1 VIDEO/AUDIO IN
To connect the LCD TV/DVD to a VCR with an S-Video cord
If you connect a VCR with a S-Video cable to the S-VIDEO IN jack on the rear side of the unit, you must also
connect the audio cables to the LINE 1 AUDIO IN jacks on the rear side of the unit.
The S-Video cable only carries the video signal. The audio signal is separate.
NOTE:
• When the S-Video cable and the standard video cable are connected at the same time, the S-Video cable
takes precedence.
Rear of the unit
VCR
To LINE 1 AUDIO IN
To Audio OUT
Audio cord (not supplied)
S-Video cord (not supplied)
To S-VIDEO IN
To S-Video OUT
To connect to a DVD player with Component Video Input
You can enjoy a high quality picture by connecting the unit’s COMPONENT VIDEO OUT jacks of your DVD
player with the COMPONENT video cables (not supplied).
To Component OUT
Y
Rear of the unit
To COMPONENT IN
P
B
DVD
P
R
Component video cord
(not supplied)
Audio cord (not supplied)
To LINE 2 AUDIO IN
To Audio OUT
NOTE:
• Component Video input of the unit are for use with a device which output 480i/1080i interlaced signals and
480p/720p progressive signals.
36
51F0101A_eng.indd 36
3/10/08 10:56:11 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections to other equipment
(continued)
To connect a HDMI or a DVI device to the unit
The HDMI input receives digital audio and uncompressed video from a HDMI device or uncompressed digital
video from a DVI device.
When you connect to a DVI device with a HDMI-to-DVI adapter cable, it transfers only video signal. Separate
analog audio cords required.
Rear of the unit
To HDMI 1/DVI IN
HDMI - to - DVI adapter cable
(HDMI type A connector)
(not supplied)
DVI device
To DVI output
To PC/DVI AUDIO IN
Audio cord (not supplied)
or
HDMI cable (type A connector)
HDMI device
(not supplied)
To HDMI 2 (or HDMI 1/DVI) IN
To HDMI out
NOTE:
• When you connect a DVI device, you must connect only with HDMI 1/DVI.
When using HDMI 1 to connect your HDMI or DVI devices, you must select the corresponding audio
input source (HDMI or DVI) on the menu screen (see ”Selecting the HDMI audio input source” on
page 24). Otherwise you will only see the image with no sound.
• If you connect an external component (cable box, satellite receiver, etc.) to this LCD TV using an HDMI cable
or a DVI to HDMI cable, the image will not display if the output resolution of the component is set to 480i. To
receive the picture you must change the output resolution on the external component.
Should you require further instruction, please contact the manufacturer of the external component.
Using an AV Amplifier with built-in digital surround
If you are using an Amplifier with built-in digital surround sound, you can enjoy various audio systems including
Dolby Digital Surround audio that sounds just like the movie.
Connect an AV amplifier with built-in Dolby Digital decoder, DTS decoder, or MPEG decoder etc. as
shown below.
Rear of the unit
Front
Speaker
(Right)
Subwoofer
TV/DVD
Front
Speaker
(Left)
Coaxial Digital
Audio Output
Coaxial digital cable
(not supplied)
To Coaxial
Digital Audio Input
Center Speaker
Surround
Speaker (Left)
Surround
Speaker
(Right)
AV Amplifier with built-in digital surround
decoder as listed above
NOTE:
• When you are viewing digital broadcast, this unit will not work in conjunction with DTS audio or MPEG audio.
There will be no sound output if connected to an AV amplifier with a built-in DTS decoder or MPEG decoder.
• Coaxial digital audio output is active only when receiving digital broadcasting, not when receiving analog
broadcasting.
37
51F0101A_eng.indd 37
3/10/08 10:56:11 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections to other equipment
(continued)
To connect an audio system
This connection allows you to use an audio amplifier and external speakers, and adjust the audio level using the
TV’s remote control.
To control the audio, turn on the unit and the stereo amplifier, and turn off the unit’s built-in speakers (see
“Turning off the built-in speakers” on page 24).
NOTE:
Rear of the unit
• To hear sound when using an
external audio amplifier, the
volume of both the unit and the
Amplifier
amplifier must be set above 0
(zero).
For example, if the volume of the
unit is set to 0, you will not be
able to hear any sound, even if
the volume of the amplifier is at its
highest level.
To Audio (L) Input
To Audio (R) Input
Audio cord (not supplied)
To connect the TV/DVD to a camcorder, or a TV Game
To playback from a camcorder, connect the camcorder to the unit as shown.
This unit can also be used as a display device for many video games. However, due to the wide variety of
signals generated by these devices and subsequent hook-up variations required, they have not all been
included in the suggested connection diagrams.You’ll need to consult each component’s Owner’s Manual for
additional information.
Rear of the unit
To LINE 1 or LINE 2 VIDEO/AUDIO IN
To Audio/Video OUT
or
Audio/Video cord
(not supplied)
To connect the TV/DVD to a PC (Personal Computer)
Before you connect this TV/DVD to your PC, change the adjustment of your PC’s Resolution and Refresh rate
(60 Hz).
Connect one end of a (male to male) VGA cable to the video card of the computer and the other end to the VGA
connector PC MONITOR on the rear of the TV/DVD. Attach the connectors firmly with the screws on the plug. In
case of a Multimedia computer, connect the audio cord to the audio output of your Multimedia computer and to
the AUDIO connector of the PC/DVI AUDIO IN jack of the TV/DVD.
Press INPUT SELECT on the remote control to select PC mode.
Switch on the computer. The TV/DVD can operate as the computer monitor.
Rear of the unit
Monitor Display modes
To PC IN
MODE
Resolution
Refresh rate
VGA
640x480
720x400
800x600
1024x768
1280x768
1280x720
1360x768
60Hz
70Hz
60Hz
60Hz
60Hz
60Hz
60Hz
VGA
SVGA
XGA
PC/DVI
AUDIO IN
jack
WXGA
WXGA
WXGA
VGA cable (not supplied)
Audio cord (not supplied)
To return to normal mode
Press INPUT SELECT again.
NOTE:
• The on-screen displays will have a different appearance in PC mode than in TV mode.
• If there is no video signal from the PC when the unit is in PC mode, “No signal” will appear on the TV-screen.
38
51F0101A_eng.indd 38
3/10/08 10:56:12 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
Reception disturbances
Most types of television interference can be remedied by adjusting the height and position of the VHF/
UHF antenna. Outdoor antennas are recommended for best results. The most common types of television
interference are shown below. If one of these symptoms appear when the TV is connected to a Cable TV
system, the disturbance may be caused by the local Cable TV company broadcast.
IGNITION
Black spots or horizontal streaks may appear, the picture may flutter or
drift. Usually caused by interference from automobile ignition systems,
neon lamps or AC powered tools and appliances such as drills or hair
dryers.
GHOSTS
Ghosts are caused by the television signal following two paths. One is the
direct path and the other is reflected by tall buildings, hills or other large
objects. Changing the direction or position of the antenna may improve
the reception.
SNOW
If the TV is located far from the TV station, in a fringe reception area where
the signal is weak, small dots may appear in the picture.
If the signal is extremely weak, the installation of a larger external antenna
may be necessary.
RADIO FREQUENCY INTERFERENCE (RFI)
Caused by two-way radios, this type of interference produces moving
ripples or diagonal streaks in the picture. Some cases may cause a loss of
contrast in the picture. Changing the direction and position of the antenna
or installing an RFI filter may improve the picture.
PICTURE SIZE VARIATION
A slight picture size variation is normal when you adjust the CONTRAST or
BRIGHTNESS settings.
CARE AND MAINTENANCE
To prevent fire or shock hazard, disconnect the TV from the power source before cleaning.
The finish on the cabinet may be cleaned with mild soap and a soft, damp cloth and cared for as other furniture.
Use caution when cleaning or wiping the plastic parts.
39
51F0101A_eng.indd 39
3/5/08 5:06:09 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting
Use the following check list for troubleshooting when you have problems with your TV/DVD. Consult your local
dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
SYMPTOMS
POWER
POSSIBLE SOLUTIONS
PAGE
• Make sure the power cord is plugged in.
TV/DVD does not operate. • Power is off, check fuse or circuit breaker.
• Unplug unit, then plug it back in.
12
TV BROADCAST RECEPTION
• Station or Cable TV experiencing problems, tune to another station.
16, 17
16, 17
39
• Check Volume adjustments or muting.
• Check for sources of possible interference.
• Check “Speakers” setting in the menu.
Poor sound or no sound.
Poor picture or no picture.
24
•
Station or Cable TV experiencing problems, tune to another station.
16, 17
13, 14
39
• Check antenna or Cable TV connections, reorient antenna.
• Check for sources of possible interference.
• Check picture control adjustments.
21
• Station or Cable TV experiencing problems, tune to another station.
• Station signal is weak, reorient antenna to receive stronger station.
• Check for sources of possible interference.
16, 17
13
39
Poor reception on some
channels.
•
Station or Cable TV experiencing problems, tune to another station.
16, 17
15
21
• Make sure channels are set into memory.
• Check picture control adjustments.
Poor color or no color.
• Check antenna or Cable TV connections, reorient antenna.
• Check for sources of possible interference.
13, 14
39
•
Station or Cable TV experiencing problems, tune to another station.
16, 17
15
–
13
• Make sure channels are set into memory.
• Cable TV company is scrambling signal.
• Check antenna orientation.
Picture wobbles or drifts.
No Cable TV reception.
• Check all Cable TV connections.
• Set Signal Type option to the “Cable” mode.
• Station or Cable TV system problems, try another station.
14
15
16, 17
Horizontal or diagonal
bars on screen.
• Check antenna connections, reorient antenna.
• Check for sources of possible interference.
13
39
No reception above
channel 13.
• Make sure Signal Type option is in the appropriate mode.
• If using antenna, check UHF antenna connections.
15
13
• No broadcast on station tuned.
• Sleep Timer is set.
• Power interrupted.
16, 17
17
–
TV shuts off.
• TV station experiencing problems or program tuned is not closed
captioned. Try another channel.
• Check Cable TV connection or VHF/UHF antenna, reposition or
rotate antenna.
• Set Closed caption in the menu.
16, 17
13, 14
20
Closed - Caption is not
activated.
Display is not shown in
your language.
• Select proper language in the menu options.
15
• The LCD panel is a very high technology product, giving you fine picture details. Occasionally, a few non-
active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not
affect the performance of your product.
40
51F0101A_eng.indd 40
3/5/08 5:06:10 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and troubleshooting
(continued)
SYMPTOMS
POSSIBLE SOLUTIONS
PAGE
DVD
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play CD-ROMs, etc.
26
8
8
Playback doesn’t start.
No picture.
• TV/DVD selector is not set correctly.
25
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
• Select the correct Audio Output position on AV amplifier.
–
26
37
No sound.
Picture is distorted during
CUE or REVIEW.
• The picture will be distorted occasionally.
• Some discs may not allow some functions.
–
Stopping playback,
search, slow-motion play,
repeat play, or program
play, etc. cannot be
performed.
–
No on-screen display.
No surround sound.
• Select Display On.
32
37
• The setup does not match your stereo system.
The unit or remote
operation key is not
functioning.
• Turn off the unit and unplug the AC power cord for several minutes,
then replug it.
12
33
Playback does not start
when the title is selected.
• Check the Parental setup.
Audio soundtrack and/or
subtitle language is not
changed when you play
back a DVD.
• Multilingual language is not recorded on the DVD disc.
31
• Some discs have no subtitles.
• Subtitles are cleared. Press SUBTITLE.
No subtitle.
31
31
Angle cannot be changed. • Multi-angles are not recorded on the DVD disc.
“ ” appears on the
screen.
• The function is prohibited with the unit or the disc.
26
REMOTE CONTROL
• Aim at the remote control at the remote sensor.
• Operate within Approx. 15 feet or reduce the light in the room.
• Clear the path of the beam.
The remote control does
not function.
12
• The batteries are weak. Replace the batteries.
•
Check the batteries are inserted correctly.
41
51F0101A_eng.indd 41
3/5/08 5:06:10 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
MODEL
L26HD32D
L32HD32D
GENERAL
Power supply
Power consumption
AC 120V 60Hz
Operation: 120W
Stand by: 1W
Operation: 160W
Stand by: 1W
Weight
8.8 kg (19.4 lbs)
12.0 kg (26.5 lbs)
Dimensions
Width: 663 mm (26-1/8 inches)
Height: 495 mm (19-1/2 inches)
Depth: 211 mm (8-5/16 inches)
Width: 796.5 mm (31-3/8 inches)
Height: 581 mm (22-7/8 inches)
Depth: 214 mm (8-7/16 inches)
Operating temperature
Operating humidity
TELEVISION
Type
5˚C - 40˚C
Less than 80%
26.01 inches (660.5 mm diagonal)
Transmission TFT color LCD panel
1366 (H) x 768 (V)
31.5 inches (800.4 mm diagonal)
Display method
Number of Pixels
Tuner type
NTSC standard
ATSC standard (8VSB), QAM
Receiving channels
VHF
UHF
2-13
14-69
CATV 14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
Inputs
S-Video: Y-Input:1.0 V (p-p), 75 ohms
C-Input:0.3 V (p-p), 75 ohms
Video: (RCA) 1 V p-p/75 ohms
Audio:
Component video:
(RCA) –8 dBm/50K ohms
(Y) 1 V (p-p), 75 ohms
(PB)/(PR) 0.7 V (p-p), 75 ohms
HDMI: HDMI compliant (type A connector)
HDCP compliant
E-EDID compliant
Suggested scan rates: 1080i, 480p, 480i, 720p
HDMI Audio: 2-channel PCM
32/44.1/48 kHz sampling frequency
16/20/24 bits per sample
PC Monitor: Mini-Dsub 15pin x 1
Antenna:
VHF/UHF In 75 ohms coaxial
Outputs
Digital audio out:
0.5 Vp-p 75 ohms terminated
Variable audio out: 0-600mV/1k ohms
41 mm x 122 mm (1-5/8 inches x 4-13/16 inches), 8 ohms x 2
5.0W + 5.0W
Speaker
Audio output power
DVD/CD player
Signal system
Applicable disc
NTSC
1.DVD (12 cm, 8 cm)
2.CD (12 cm, 8 cm)
Pickup
CD: Wavelength: 790 nm
Maximum output power: 7 mW
DVD: Wavelength: 655 nm
Maximum output power: 5 mW
ACCESSORIES
Remote control
Batteries (UM-4) x 2
AC Cord
Designs and specifications are subject to change without notice.
42
51F0101B_eng.indd 42
4/4/08 10:04:04 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
TTE Technology, Inc. (“TTE”) Limited Warranty
All LCD Models
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER,
AND AS DESCRIBED BELOW TTE EXPRESSLY DISCLAIMS, ALL ACTUAL AND IMPLIED WARRANTIES
WITH RESPECT TO ANY PRODUCT USED FOR INSTITUTIONAL OR OTHER COMMERCIAL PURPOSES
(INCLUDING BUT NOT LIMITED TO RENTAL PURPOSES).
What your warranty covers: Defects in materials or workmanship to the original owner
New LCD Televisions - Screen Sizes 32” and smaller:
• For how long after your purchase:
• Ninety (90) days from date of purchase for labor charges. After ninety (90) days, labor charges will be at
owner expense.
• One (1) year from date of purchase for parts.
• What we will do:
• At TTE’s discretion, pay an Authorized RCA Service Center for both labor charges and parts to repair
your television, or replace your television with a new or refurbished/remanufactured unit.
• See “How to get service”
New LCD Televisions - screen sizes 33” through 47”:
• For how long after your purchase:
• One (1) year from the date of purchase for labor charges.
• One (1) year from the date of purchase for parts.
• What we will do:
• At TTE’s discretion, pay an Authorized RCA Service Center for labor charges and parts to repair your
television, or replace your television with a new or refurbished/remanufactured unit.
• See “How to get service”
All Remanufactured/Refurbished LCD Televisions:
• For how long after your purchase:
• Ninety (90) days from date of purchase for labor charges.
• Ninety (90) days from date of purchase for parts.
• What we will do:
• At TTE’s discretion, pay an Authorized RCA Service Center for both labor charges and parts to repair
your television, or replace your television with a refurbished/remanufactured unit.
• See “How to get service”
How to get service:
• Call 1-800-951-9582. Please have your unit’s date of purchase and model/serial number ready. The model/
serial number information can be found on the back of your unit.
• A representative will troubleshoot your problem over the phone.
• If it is determined that your unit requires service, the service location will be at the sole discretion of TTE
based upon the TTE Limited Warranty statement.
• At the sole discretion of TTE, television screen sizes 32” and smaller is either consumer carry-in to an
Authorized RCA Service Center or directly exchanged for a new or refurbished/remanufactured unit.
• At the sole discretion of TTE, television screen sizes 33” through 47” is either consumer carry-in to an
Authorized RCA Service Center or directly exchanged for a new or refurbished/remanufacture unit.
• Proof of purchase in the form of a bill of sale or receipted invoice from an Authorized Dealer which is evidence
that the product is within the warranty period must be presented to obtain warranty service.
What your warranty does not cover:
• Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your unit. Any
additional information should be obtained from your dealer.)
• Installation and related adjustments.
• Damage resulting from non-approved installation methods.
43
51F0101A_eng.indd 43
3/5/08 5:06:11 PM
Download from Www.Somanuals.com. All Manuals Search And Download.
• Signal reception problems not caused by your unit.
• Damage from misuse or neglect.
• Batteries.
• A television that has been modified or incorporated into other products or is used for institutional or other
commercial purposes (including but not limited to rental purposes).
• A unit purchased or serviced outside the U.S.A.
• Acts of nature, such as but not limited to lightning damage.
• Special, incidental or consequential damages.
Product Registration:
com/television. It will make it easier to contact you should it ever be necessary. The return of the card is not
required for warranty coverage.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT.
NO VERBAL OR WRITTEN INFORMATION GIVEN BY TTE TECHNOLOGY, INC., ITS AGENTS OR
EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE OR MODIFY THE SCOPE OF
THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER. TTE TECHNOLOGY, INC. SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER
OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED BY THE LAWS OF THE STATE OF
INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE APPLICABLE WARRANTY AND WARRANTY PERIOD SET FORTH ABOVE.
How State Law relates to this warranty:
• Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on
how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.
• This warranty gives you specific legal rights, and you also may have other rights that vary from state to state.
If you purchased your unit outside the United States or seek warranty coverage outside the United
States:
• This warranty does not apply. Contact your dealer for warranty information.
Service calls which do not involve defective materials or workmanship are not covered by this warranty.
Costs of such service calls are the sole responsibility of the purchaser.
Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only
add delays in service for your product.
TTE Technology, Inc.
101 West 103rd Street
Indianapolis, IN 46290
©2008 TTE Technology Inc.
RCA and associated marks are trademarks of THOMSON S.A.
used under license to TTE Corporation.
Printed in Thailand
N
J51F0101B SH 08/05
51F0101B_eng.indd 44
4/4/08 10:04:05 AM
Download from Www.Somanuals.com. All Manuals Search And Download.
|