Tocom: 5643 519A
PLEASE READ AND SAVE THIS FOR FUTURE REFERENCE
For your records
In the event that service should be required,
you may need the model number and the
serial number. In the space below, record
the date and place of purchase and the
serial number:
Model No.:
Date of Purchase:
Place of Purchase:
Serial No.:
FCC information
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that may
cause undesired operation.
Getting started
Important information
IMPORTANT SAFETY INSTRUCTIONS
Some of the following information may not
apply to your particular product; however, as
with any electronic product, precautions should
be observed during handling and use.
Read these instructions.
Keep these instructions.
damaged, liquid has been
spilled or objects have fallen
into the apparatus, the
apparatus has been exposed
to rain or moisture, does not
operate normally, or has been
dropped.
Plugging in for power
Insert the connector of the AC/DC adpater
to the power jack at the bottom of the
unit.
External AC/DC adaptor input power
supply: 100-240V ~ 50/60Hz
Power failure indicator
Technical information
Product: Clock Radio
Brand: RCA
Safety precautions
user manual
manual de usuario
When external DC power is interrupted
(disconnected) for a short period of time,
both time and alarm settings will change
(unless batteries are installed). After
external DC power is restored (reconnected),
the Digital Display will blink to indicate that
power was interrupted and you should
readjust the time and alarm settings.
•
Make sure that you keep your set
away from water and high
temperatures.
Model: RP5500i, RP5502i
•
•
•
•
•
•
•
•
Do not use your system immediately
after transporting it from a cold place
to a warm place, as condensation may
cause the system to malfunction.
Keep your unit away from humid areas
and abnormally hot places.
In accordance with FCC requirements,
changes or modifications not expressly
approved by Thomson Inc. could void the
user’s authority to operate this product.
This device generates and uses radio
frequency (RF) energy, and if not installed
and used properly, this equipment may
cause interference to radio and television
reception.
If this equipment does cause interference to
radio or television reception (which you can
determine by unplugging the unit), try to
correct the interference by one or more of
the following measures:
Portable Cart
Warning
Heed all warnings.
Electrical consumption
RP5500i
RP5502i
Follow all instructions.
External AC adaptor: 10V
1.4A
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
Note:
Power consumption: 120VAC x 0.7A
•
•
•
•
•
•
ADDITIONAL SAFETY INFORMATION
Apparatus shall not be exposed to dripping
or splashing and no objects filled with
liquids, such as vases, shall be placed on
the apparatus.
Always leave sufficient space around the
product for ventilation. Do not place
product in or on a bed, rug, in a bookcase
or cabinet that may prevent air flow
through vent openings.
Do not place lighted candles, cigarettes,
cigars, etc. on the product.
Connect power cord only to AC power
source as marked on the product.
Care should be taken so that objects do
not fall into the product.
Do not attempt to disassemble the cabinet.
This product does not contain customer
serviceable components.
IF YOUR PRODUCT OPERATES ON
BATTERIES, adhere to the following
precautions:
A. Any battery may leak electrolyte if
mixed with a different battery type, if
inserted incorrectly, or if all batteries are
not replaced at the same time.
B. Any battery may leak electrolyte or
explode if disposed of in fire or an attempt
is made to charge a battery not intended
to be recharged.
Power is fed to the unit even when it is not
functioning. To cut the power supply off,
the power cable must be unplugged.
Service information
This product should be serviced only by
those specially trained in appropriate
servicing techniques. For instructions on
how to obtain service, refer to the warranty
included in this user manual.
To prevent personal injury, do not
reverse any batteries.
The use of apparatus in moderate
climates.
The apparatus should not be exposed
to dripping or splashing and no objects
filled with liquids, such as vases, should
be placed on the apparatus.
No naked flame sources, such as lighted
candles, should be placed on the
apparatus.
Attention should be drawn to the
environmental aspects of battery
disposal.
Minimum distances (2cm) should be
kept around the apparatus for
sufficient ventilations.
The ventilation should not be impeded
by covering the ventilation opening
with items, such as newspaper, table-
cloths, curtains, etc.
The descriptions and characteristics in this
owner’s manual are for the purpose of
general reference only and not as a
guarantee. In order to provide you with the
highest quality product, we may make
changes or modifications without prior
notice. The English version serves as the
final reference on all product and
manufacturer’s instructions.
•
•
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.
Battery back-up operation
This clock radio is equipped with a memory
holding system that can be powered with 2
“AA” batteries (included). The power
•
The AC/DC Adaptor supplied with this
product is intended to be correctly
orientated in a vertical or floor mount
position.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third grounding
prong. The wide blade or the third prong is
provided for your safety. If the provided
plug does not fit into your outlet, consult
an electrician for replacement of the
obsolete outlet.
Protect the power cord from being walked
on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
Only use attachments/accessories specified
by the manufacturer.
failure protection circuit will not operate
unless battery is installed. When normal
household power is interrupted, or AC line
cord is unplugged, the batteries will power
the clock radio to keep track of time and
alarm settings programmed into memory.
When the battery backup functions, the
digital display will not light, however, the
function of alarm still occurs during the
power interruption if remaining battery
power is adequate. Normal operation will
resume after AC power is restored so you
will not have to reset the time or the alarm.
•
•
•
•
•
•
•
•
•
•
•
Re-orient the receiving antenna (that is,
the antenna for the radio or television
that is “receiving” the interference).
Move the unit away from the
equipment that is receiving
operational details should any discrepancies
arise in other languages.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
iPod is a trademark of Apple Computer,
Inc., registered in the U.S. and other
countries.
interference.
T H E L I G H T N I N G CAUTION: TO REDUCE THE
THE EXCLAMATION
IMPORTADOR
Comercializadora Thomson de México, S.A.
de C.V.
FLASH AND ARROW-
HEAD WITHIN THE
RISK OF ELECTRIC SHOCK, POINT WITHIN THE
Plug the unit into a different wall
outlet so that the unit and the
equipment receiving interference are
on different branch circuits.
DO NOT REMOVE COVER T R I A N G L E I S
A
•
TRIANGLE IS
WA R N I N G
ALERTING YOU OF
A
WARNING
SIGN
( O R B A C K ) . N O U S E R -
SERVICEABLE PARTS IN-
SIDE. REFER SERVICING
TO Q U A L I F I E D S E RV I C E
PERSONNEL.
S I G N
ALERTING YOU OF
•
I
I
M
P
T
O
R
T
T
A
I
N
T
S
"
D
A
N
G
E
R
O
U
S
N
S
R
U
C
O
N
Álvaro Obregón No. 151. Piso 13.
Col. Roma. Delegación Cuauhtémoc
C.P. 06700. México, D.F.
VOLTAGE" INSIDE
THE PRODUCT.
A C C O M PA N Y I N G
H
T
E
P
R
O
D
U
C
T.
If these measures do not eliminate the
interference, please consult your dealer or
an experienced radio/television technician
for additional suggestions. Also, the Federal
Communications Commission has prepared
a helpful booklet, “How To Identify and
Resolve Radio TV Interference Problems.”
This booklet is available from the U.S.
Government Printing Office, Washington,
DC 20402. Please specify stock number 004-
000-00345-4 when ordering copies.
•
•
SEE MARKING ON BOTTOM / BACK OF PRODUCT
•
The rating plate is located at the
bottom cabinet of apparatus.
Telefono: 52-55-11-020360
WARNING:TO PREVENT FIRE OR ELECTRICAL
Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Install battery as follow:
RFC: CTM-980723-KS5
DO NOT EXPOSETHIS PRODUCT
SHOCK HAZARD,
TO RAIN OR MOISTURE.
1. Remove battery compartment door
(located at the bottom of the radio)
by applying thumb pressure to the
tab on battery door and then lift the
door out and off the cabinet.
2. Insert 2 AA batteries (included).
3. Replace the compartment door.
Maintenance
EXPORTER
Thomson Inc.
P.O. Box 1976
Clean the unit with a soft cloth, or a damp
chamois leather. Never use solvents.
This Class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la class B est
conforme à la norme de NMB-003 du
Canada.
•
•
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
C. Discard leaky batteries immediately.
Leaking batteries can cause skin burns or
other personal injury. When discarding
batteries, be sure to dispose of them in the
proper manner, according to your state/
provincial and local regulations.
Indianapolis, IN 46206 - 1976
©2007 Thomson Inc.
Trademark(s) ® Registered
Marque(s) ® Deposée(s)
Marca(s) ® Registrada(s)
Printed in China / Impreso en China
Note: we recommend that you replace the
batteries every 2-3 years.
EN/E
It is important to read this instruction book prior to using your new product for the first time.
Es importante leer este manual antes de usar por vez primera su euipo.
General controls
General controls
Clock
Clock
Radio & USB
Front view
Auto clock set
US time zones
Listening to the radio
Side views
4. Press
next file. Press and hold
search backward or forward.
5. Press SHUFFLE to play the files in the
flash player in random order. The icon
shows on the display when shuffle
mode is active. Press again to cancel
the function.
6. Press REPEAT to select a repeat
playback mode. Corresponding icon
shows on the display:
– repeat the current file
– repeat all files
Press REPEAT until no repeat icon
shows on the display to cancel the
repeat playback.
/
to skip to the previous or
Setting clock
/
to
1. Press RADIO on the front of the unit
to turn on the radio.
You do not have to set the clock time as a
built-in automatic time set system is
equipped in this clock powered by 3V (2 AA
batteries, included and installed). All you
have to do is to plug this clock for power
and current time will be shown
In case the memory holding batteries are
accidentally removed, set the clock
manually as below:
2. Slide BAND to select the radio band.
The selected radio band shows on the
display.
Display
1. Press SET on the top of the unit until
the clock setting icon flashes on the
display.
3. Rotate TUNING to select frequency. The
selected frequency shows on the
display.
Turns off the unit
(standby mode)
Adjusts the volume
Selects the radio
frequency
2. Rotate the knob on the top of the unit
to set the clock time. The time
decrements or increments follows by a
faster rate when you rotate and hold
the knob. The clock setting icon
flashes when you are setting the time.
AM or PM icon also shows beside the
time.
3. To save and exit the clock setting, wait
for about 5 seconds or press SET until
the clock setting , WAKE 1 or WAKE
2 icon is off. The clock time is now set.
automatically after setting the time zone
and daylight saving time (read below).
However, the batteries can also be
exhausted and we recommend that you
replace the batteries every 2-3 years.
4. Press OFF to turn off the radio.
Selects random
playback mode
Selects the display
brightness
Selects the radio
band
Built-in AFC
The Built-in Automatic Frequency Control
(AFC) works only on FM. It helps reducing
drift on FM reception and keeping the
radio locked in on the FM station to which
it is tuned.
When tuning in FM stations, you may notice
that the station you are tuning can
be well-tuned on two or three nearby
points on the dial. Always tune carefully
at the loudest and clearest point.
Selects repeat
playback mode
Universal dock for iPod®
(push to open or close)
Setting time zone
Slide the time zone selector at the bottom
of the unit to Eastern, Central, Mountain or
Pacific time zone (refer to the maps on the
right).
Skips to the previous or
next file,
searches backward or
forward
Note:
Selects radio, USB
or iPod mode
•
You may charge the battery of your
USB flash player through the USB jack
(5V 500mA) while the unit is in the USB
mode. Charging control should be
operated on the USB flash player.
The unit supports Microsoft FAT12, 16
& 32 and ISO9660 file systems only.
Other file systems from Linux, MAC or
NTFS are not supported.
Daylight saving time
Bottom view
Press and hold the Daylight Saving Time
button at the bottom of the unit to turn
on/ off in areas observing/ not observing
Canadian time zones
Top view
Press SET at the center to select adjusting the clock
time, wake time 1 or wake time 2. Rotate the knob to
adjust the clock time, wake time 1 or wake time 2.
•
AM Antenna
Time zone selector (refer to “Clock”)
A built-in ferrite rod antenna eliminates the
need for an outside antenna for AM
reception. Rotating the unit slightly may
improve reception of distant AM stations.
such time change. The icon
the display when daylight saving time is
active.
shows on
USB connector
•
•
•
•
•
Only mpeg 1/2 layer 3 format is
supported for mp3 files.
Digital Right Management (DRM) type
music files will not be played.
Only the first 999 mp3 files can be
read.
The unit reads all files in folders and
displays them as tracks only.
Only USB flash player is supported.
Other USB devices such as MTP USB
flash player, USB hub or USB card
reader are not supported.
WARNING: Avoid playing with these
buttons when setting clock or wake time.
Listening to the external USB
flash player
Daylight saving time button
(refer to “Clock”)
1. Connect an external USB flash player
(with mp3 music) to the USB connector
at the top of the unit.
Display brightness
Press BRIGHTNESS to dim the display and
press again to restore to the original
brightness level. When the display is
dimmed, the blue indicator on the universal
dock for iPod will also be turned off.
Battery compartment lock
2. Press USB on the front of the unit to
select the USB mode.
3. Playback from the USB flash player
starts automatically. Press USB to pause
the playback (the TRACK icon flashes
during pause) and press again to
resume.
•
Never connect the unit to a computer.
Doing so may cause damage to the
unit and the computer.
Battery compartment
(refer to “Battery back-up operation”)
Activates wake time 2
Activates wake time 1
Refer to “Sleep function”
Refer to “NAP function”
Power jack for AC/DC adapter (10V
1.4A)
Turns off the wake function momentarily,
turns off the sleep funtion
•
Acts of nature, such as but not limited to
lightning damage.
U.S. Limited Warranty
What your warranty covers:
Product Registration:
•
iPod
Wake function
Wake function
Sleep function
•
Defects in materials or workmanship.
Please complete and mail the Product
registration Card packed with your unit. It
will make it easier to contact you should it
ever be necessary. The return of the card is
not required for warranty coverage.
For how long after your purchase:
•
90 days from date of purchase - unit
exchange, which includes parts and labor.
91 days to 1 year from date of purchase -
unit exchange, which includes parts only;
you pay the labor.
Waking to Alarm (
)
Waking to USB (
)
In the sleep mode, the radio, iPod or USB
flash player (if connected) turns off
automatically. To set the sleep time, simply:
Listening to iPod
Set the wake time
•
If the iPod or USB mode is selected in
your last sleep function setting, the
iPod or USB flash player will start to
play, instead of the radio. The radio
will be played whenever the iPod or
USB mode is selected but without the
corresponding device connected.
Turn off the wake function
Adapters
Note:
3. Adjust the volume to your desired
level. The first file on the USB flash
player will be played when the wake
function activates.
1. Push the universal dock for iPod on the
front of the unit to open it.
This unit allows 2 wake times to be set.
1. Press SET on the top of the unit until
the icon WAKE1 or WAKE2 flashes on
the display.
•
Silence the wake function momentarily:
Press SNOOZE. The alarm will sound
again when the snooze period is over.
(refer to “SmartSnoozeTM”).
•
The unit equips with GRAD-U-WAKE
Limitation of Warranty:
•
feature, the alarm tone volume will
increase gradually to its maximum in
about 30 to 45 seconds.
2. Eight adapters are supplied. Check the
table on the right and use the
appropriate adapter for your iPod.
3. Place the adapter and then your iPod
on the universal dock for iPod.
4. Press iPod on the front of the unit to
select the iPod mode.
THE WARRANTY STATED ABOVE IS THE
ONLY WARRANTY APPLICABLE TO THIS
PRODUCT. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED (INCLUDING ALL
IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE) ARE HEREBY
DISCLAIMED. NO VERBAL OR WRITTEN
INFORMATION GIVEN BY THOMSON INC.,
ITS AGENTS OR EMPLOYEES SHALL CREATE
A GUARANTY OR IN ANY WAY INCREASE
THE SCOPE OF THIS WARRANTY.
REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. THOMSON
INC. SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR
ARISING OUT OF ANY BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT. THIS DISCLAIMER OF
WARRANTIES AND LIMITED WARRANTY
ARE GOVERNED BY THE LAWS OF THE
STATE OF INDIANA. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW,
ANY IMPLIED WARRANTY OF
What we will do:
•
1. Press SLEEP repeatedly to cycle among
the sleep time available (90min, 60min,
30min, 15min and OFF. 90min is the
default setting).
Provide you with a new, or at our option, a
refurbished unit. The exchange unit is
under warranty for the remainder of the
original product’s warranty period.
Proof of purchase in the form of a bill of
sale or receipted invoice which is evidence
that the product is within the warranty
period must be presented to obtain
warranty service. For rental firms, proof of
first rental is also required.
4. Press OFF to turn off the unit.
2. Rotate the knob on the top of the unit
to set the wake time. The time
decrements or increments follows by a
faster rate when you rotate and hold
the knob.
3. To save and exit the wake time setting,
wait for about 5 seconds or press SET
until all clock setting , WAKE 1 and
WAKE 2 icons are off. The wake 1 or
wake 2 time is now set.
•
If you set the wake function with low
volume level before going to bed, we
advise using Waking to Alarm mode to
wake you up since the volume will
automatically increase.
When the AC power is disconnected, all
wake mode will be reverted to alarm
tone.
OR
3. Select a radio station as usual, OR
Note: If there is no USB flash player
connected, the alarm tone will sound
instead even if Waking to USB mode is
selected.
Press iPod or USB and then press
/
•
•
Stop the wake function:
Press OFF. The alarm will be on again
the following day at the same time.
•
If necessary, press
/
to further set
•
to select a file on the iPod or USB flash
player. Playback will be in repeat all
files mode automatically.
the sleep time. Each press of the
button will decrease or increase one
minute. For example, to set 35 min,
press SLEEP to select 30min and then
5. Playback from the iPod starts
automatically. Press iPod to pause the
playback and press again to resume.
•
•
•
•
Press SLEEP once to check the
OR
remaining sleep time. Press SLEEP
repeatedly to select another sleep time.
If you decide to turn off the unit
sooner, press SNOOZE, OFF or press
SLEEP repeatedly to select “OFF”.
When the sleep mode is activated
again, the sleep time will be the same
as the one you have set before.
6. Press
next file. Press and hold
search backward or forward.
/
to skip to the previous or
Note: When the wake function activates,
the corresponding wake icon will flash
until the wake function is turned off. The
icon will then stop flashing and keep
lighting up.
press
The icon
5 times.
flashes while selecting.
How to make a warranty claim:
•
/
to
Disable the wake function permanently:
Press WAKE 1 or WAKE 2 repeatedly
until no corresponding wake indicator
•
•
Properly pack your unit. Include any cables,
etc., which were originally provided with
the product. We recommend using the
original carton and packing materials.
Include evidence of purchase date such as
the bill of sale. Also print your name and
address and a description of the defect.
Send via standard UPS or its equivalent to:
Thomson Inc.,Product Exchange
Center, 11721 B Alameda Avenue,
Socorro, Texas 79927
Waking to RADIO (
)
•
To check the wake time after setting,
press SET until the icon WAKE1 or
WAKE2 flashes and the respective
assigned wake time shows on the
display.
2. When the desired sleep time is
selected, release SLEEP and wait for
about 5 seconds, the sleep time is now
set. The radio (default) turns on and
3. Select a desired wake up radio channel
(refer to “Listening to the radio”). If no
wake up channel is set, your last
listening radio station will be selected.
4. Adjust the volume to your desired
level.
7. Press SHUFFLE to play the files in
random order in the iPod. Random
playback indication shows on the iPod
when the function is activated. Press
again to cancel the function.
8. Press REPEAT to select a repeat
playback mode (repeat 1 or repeat all).
Repeat playback indication shows on
the iPod when the function is
(e.g.
display.
) shows on the
•
the icon
lights on the display.
SmartSnoozeTM
Select the wake source
5. Press OFF to turn off the unit.
This operation allows extra sleep time after
the wake function is on. The alarm will be
off by pressing SNOOZE, SLEEP or NAP
until the snooze period is over. Snooze
function can be used repeatedly up to 2
hours. After this, the wake function will
turn off until the next day.
You may be woken up by the alarm, radio,
music from iPod or USB flash player.
1. Set a wake time (refer to the above
instructions).
NAP function
Waking to iPod (
)
•
•
•
Insure your shipment for of loss or damage.
Thomson accepts no liability in case of
damage or loss en route to Thomson.
Pay any charges billed to you by the
Exchange Center for service not covered by
the warranty.
activated. Press REPEAT until no repeat
playback indication shows on the iPod
to cancel the repeat playback.
3. Adjust the volume to your desired
level. The last played file on the iPod
will be played when the wake function
activates.
2. Press WAKE 1 or WAKE 2 to select a
wake mode. Corresponding icon lights
on the front of the unit.
For catnaps up to 2 hours without
disturbing the regular alarm settings, the
NAP function wakes you up after a short
period of time. Simply:
2. When the desired NAP time is selected,
release NAP and wait for about 5
seconds, the NAP time is now set. The
current time shows and the icon
lights on the display.
3. Press NAP once to show briefly the
NAP time left.
•
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
*
For the latest iPod models, please use the
adapter provided with your iPod.
4. Press OFF to turn off the unit.
Note:
1
1
1
1
2
2
2
2
– Wake time 1 by alarm
– Wake time 1 by radio
•
You may charge the battery of your
iPod through the universal dock for
iPod while the unit is turned off
(standby mode) or in the iPod mode.
Charging control should be operated
on the iPod.
If no iPod is connected in the iPod
mode, the unit will exit the iPod mode
and turn off automatically.
A new or refurbished unit will be shipped
to you freight prepaid.
How state law relates to this warranty:
•
Set the “quiet” period as follow:
While pressing SNOOZE, rotate the knob
on the top of the unit to set the “quiet”
period from 1 to 30 minutes (default: 9
minutes). Release SNOOZE, then the
“quiet” period is set.
Made for:
Note: If there is no iPod connected, the
alarm tone will sound instead even if
Waking to iPod mode is selected.
– Wake time 1 by iPod
Some states do not allow the exclusion nor
limitation of incidental or consequential
damages, or limitations on how long an
implied warranty lasts, so the above
limitations or exclusions may not apply to
you.
This warranty gives you specific legal rights,
and you also may have other rights that
vary from state to state.
What your warranty does not cover:
•
1. Press NAP repeatedly to cycle among
the NAP time available (10min, 20min,
30min, 60min, 90min, 120min and OFF.
20min is the default setting).
iPod with video (30GB, 60GB, 80GB) 5th
generation
iPod photo (20GB U2 Special Edition, 30GB
U2 Special Edition, 40GB, 60GB) 4th
generation
– Wake time 1 by USB flash player
– Wake time 2 by alarm
– Wake time 2 by radio
– Wake time 2 by iPod
– Wake time 2 by USB flash player
Customer instruction. (Your Owner’s Manual
provides information regarding operating
Instructions and user controls. For
additional information, ask your dealer.)
Installation and set-up service
adjustments.
Only alarm tone can be selected in the
NAP mode.
Press OFF to stop the NAP alarm, OR
press and hold NAP until “OFF” is
selected to cancel the NAP function.
•
•
•
If necessary, press
/
to further set
•
•
the NAP time. Each press of the button
will decrease or increase one minute.
For example, to set 35min, press NAP
iPod (20GB, 20GB U2 Special Edition, 40GB)
•
•
•
Batteries.
Damage from misuse or neglect.
Products which have been modified or
incorporated into other products.
Products purchased or serviced outside the
USA.
4th generation
If you purchased your product outside the
USA:
•
to select 30 min and then press
times.
5
iPod nano (2GB, 4GB) 1st generation
iPod mini (4GB, 6GB) 1st & 2nd
generations
This warranty does not apply. Contact your
dealer for warranty information.
•
•
The icon
flashes while selecting.
Download from Www.Somanuals.com. All Manuals Search And Download.
|