ASMi-31
Short Range Modem
Installation and Operation Manual
Notice
This manual contains information that is proprietary to RAD Data Communications. No part of this
publication may be reproduced in any form whatsoever without prior written approval by RAD Data
Communications.
No representation or warranties for fitness for any purpose other than what is specifically mentioned in
this manual is made either by RAD Data Communications or its agents.
For further information contact RAD Data Communications at the address below or contact your local
distributor.
RAD Data Communications
Headquarters
RAD Data Communications
US East
RAD Data Communications
US West
12 Hanechoshet Street
Tel Aviv 69710 Israel
Tel: 972-3-6458181
Fax: 972-3-6498250
E-mail: [email protected]
900 Corporate Drive
Mahwah, NJ 07430 USA
Tel: (201) 529-1100
Fax: (201) 529-5777
E-mail: [email protected]
3631 South Harbor Boulevard
Suite 250
Santa Ana, CA 92704
Tel: (714) 850-0555
Fax: (714) 850-1555
© 2000 RAD Data Communications
Publication No. 646-200-03/00
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Warranty
This RAD product is warranted against defects in material and workmanship for a period of one year
from date of shipment. During the warranty period, RAD will, at its option, either repair or replace
products which prove to be defective. For warranty service or repair, this product must be returned to
a service facility designated by RAD. Buyer shall prepay shipping charges to RAD and RAD shall pay
shipping charges to return the product to Buyer. However, Buyer shall pay all shipping charges, duties
and taxes for products returned to RAD from another country.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance
by Buyer, Buyer-supplied firmware or interfacing, unauthorized modification or misuse, operation
outside of the environmental specifications for the product, or improper site preparation or
maintenance.
Exclusive Remedies
The remedies provided herein are the Buyer's sole and exclusive remedies. RAD shall not be liable for
any direct, indirect special, incidental, or consequential damages, whether based on contract, tort, or
any legal theory.
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Safety Warnings
The exclamation point within a triangle is intended to warn the operator or
service personnel of operation and maintenance factors relating to the
product and its operating environment which could pose a safety hazard.
Always observe standard safety precautions during installation, operation and maintenance of this
product. Only a qualified and authorized service personnel should carry out adjustment, maintenance
or repairs to this instrument. No adjustment, maintenance or repairs should be performed by either the
operator or the user.
Telecommunication Safety
The safety status of each of the ports on ASMi-31 is declared according to EN 41003 and is detailed in
the table below:
Ports
Safety Status
V.24, V.35, X.21, RS-530, V.36,
LAN, balanced G.703
SELV
Circuit operating with Safety Extra-Low Voltage
Line
TNV-1
Telecommunications Networks Voltage within the
limits of SELV and subject to overvoltages.
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Regulatory Information
FCC-15 User Information
This equipment has been tested and found to comply with the limits of the Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to the radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Warning per EN 55022
This is a Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Declaration of Conformity
Manufacturer's Name:
RAD Data Communications Ltd.
Manufacturer's Address:
12 Hanechoshet St.
Tel Aviv 69710
Israel
declares that the product:
Product Name:
ASMi-31/S
Conforms to the following standard(s) or other normative document(s):
EMC:
EN 55022 (1994)
Limits and methods of measurement of radio disturbance
characteristics of information technology equipment.
EN 50082-1 (1992)
Electromagnetic compatibility – Generic immunity standards
for residential, commercial and light industry.
Safety:
EN 60950 (1992/93) Safety of information technology equipment, including
electrical business equipment.
Supplementary Information:
The product herewith complies with the requirements of the EMC Directive 89/336/EEC and the Low
Voltage Directive 73/23/EEC. The product was tested in a typical configuration.
Tel Aviv, September 7th, 1997
Haim Karshen
VP Quality
European Contact: RAD Data Communications GmbH, Lyoner Strasse 14, 60528 Frankfurt am Main, Germany
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Quick Start Guide
If you are familiar with ASMi-31, use this quick start guide to prepare the
unit for operation.
Perform the following steps for both the local and the remote units.
1. Disconnect all cables from the units.
2. Open the case of the units.
3. Adjust the jumpers (see Chapter 2, Installation and Setup).
Make sure that there is only one clock source in the application. Select one
modem as INT or EXT, and the second modem as RCV.
Note
4. Close the case of the units.
5. Connect the units to the DTEs.
6. Power up the units.
7. Connect the units to the line.
The units should operate properly after a few seconds.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Quick Start Guide
ASMi-31 Installation and Operation Manual
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Contents
CHAPTER 1 INTRODUCTION
1.1 Overview....................................................................................................................... 1-1
General ................................................................................................................................1-1
Versions................................................................................................................................1-1
Application...........................................................................................................................1-2
Features................................................................................................................................1-2
1.2 Physical Description....................................................................................................... 1-3
1.3 Functional Description................................................................................................... 1-3
General ................................................................................................................................1-3
Remote Management............................................................................................................1-4
Data Transmission.................................................................................................................1-4
Master/Slave Clock Modes ....................................................................................................1-4
Special Management Configurations......................................................................................1-4
Diagnostic Capabilities..........................................................................................................1-4
Overload Protection..............................................................................................................1-5
1.4 Technical Specifications ................................................................................................. 1-5
Line Interface........................................................................................................................1-5
Digital Interface (DTE)...........................................................................................................1-5
Clock Source ........................................................................................................................1-6
Control Signals......................................................................................................................1-6
Diagnostics ...........................................................................................................................1-6
Indicators..............................................................................................................................1-6
Power...................................................................................................................................1-6
Physical ................................................................................................................................1-7
Environment.........................................................................................................................1-7
CHAPTER 2 INSTALLATION AND SETUP
2.1 Site Requirements and Prerequisites .............................................................................. 2-1
Power...................................................................................................................................2-1
Ambient Requirements .........................................................................................................2-1
2.2 Package Contents........................................................................................................... 2-2
2.3 Installation and Setup..................................................................................................... 2-2
Setting the Internal Jumpers ..................................................................................................2-2
Connecting the Interfaces......................................................................................................2-6
CHAPTER 3 OPERATION
3.1 Controls and Indicators .................................................................................................. 3-1
3.2 Operating Instructions.................................................................................................... 3-2
Turning ASMi-31 On ............................................................................................................3-2
Normal LEDs Indications.......................................................................................................3-2
Turning ASMi-31 Off ............................................................................................................3-3
CHAPTER 4 TROUBLESHOOTING AND DIAGNOSTICS
4.1 Diagnostic Tests ............................................................................................................. 4-1
Local Analog Loopback (LLB) ................................................................................................4-2
Remote Loopback (RLB)........................................................................................................4-3
ASMi-31 Installation and Operation Manual
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Table of Contents
CHAPTER 5 CARD CAGE VERSION
5.1 ASM-MN-214 Card Cage............................................................................................... 5-1
5.2 ASMi-31/R Card Version ................................................................................................ 5-3
5.3 Power Supply................................................................................................................. 5-4
AC Supply (100, 115 or 230 VAC).........................................................................................5-4
DC Supply (-48 VDC) ...........................................................................................................5-4
Power Supply with Redundancy............................................................................................5-4
5.4 Installing ASMi-31/R....................................................................................................... 5-5
APPENDIX A ETHERNET INTERFACE
APPENDIX B IR-G.703 CODIRECTIONAL INTERFACE (64 KBPS)
APPENDIX C X.21 INTERFACE MODULE
APPENDIX D DTE INTERFACE CONNECTORS
APPENDIX E CONNECTING RS-530 TO RS-422
APPENDIX F INSTALLATION IN 19" RACK
ii
ASMi-31 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Table of Contents
List of Figures
Figure 1-1 ASMi-31 Working Opposite HS-U Card in Megaplex-2100.......................................... 1-2
Figure 1-2 ASMi-31 Standalone Unit ............................................................................................ 1-3
Figure 2-1 ASMi-31 PCB Layout ................................................................................................... 2-4
Figure 2-2 ASMi-31 Rear Panel..................................................................................................... 2-6
Figure 2-3 Connecting the Line – Step 1....................................................................................... 2-7
Figure 2-4 Connecting the Line – Step 2....................................................................................... 2-7
Figure 2-5 Connecting the Line – Step 3....................................................................................... 2-7
Figure 3-1 ASMi-31 Front Panel.................................................................................................... 3-1
Figure 4-1 Local Analog Loopback................................................................................................ 4-2
Figure 4-2 Remote Digital Loopback............................................................................................. 4-3
Figure 5-1 ASM-MN-214 Rear Panel ............................................................................................ 5-2
Figure 5-2 ASMi-31/R Front Panel ................................................................................................ 5-3
Figure 5-3 ASM-MN-214 Front Panel ........................................................................................... 5-4
ASMi-31 Installation and Operation Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
List of Tables
List of Tables
Table 2-1 ASMi-31 Internal Jumpers and Switches........................................................................ 2-4
Table 2-2 DTE Interfaces and Matching Adapter Cables................................................................ 2-7
Table 3-1 Local Control Functions (via DTE) ................................................................................. 3-2
Table 3-2 ASMi-31 Controls and Indicators – Normal Operation .................................................. 3-2
iv
ASMi-31 Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 1
Introduction
This chapter describes basic physical and functional features of the
ASMi-31 standalone modem, as well as some typical applications. It
discusses the following topics:
• An overview of the modem
• Physical description
• Functional description
• Technical specifications.
1.1 Overview
The ASMi-31 modem is a synchronous/asynchronous short-range modem
which is managed by a remote master modem. ASMi-31 operates
synchronously or asynchronously at full duplex over 2-wire twisted pair,
unconditioned lines. The ASMi-31 modem has a transmission range of 8 km
(5 miles) over 24 AWG wire and operates at user-selectable data rates from
1.2 kbps to 128 kbps.
General
Versions
ASMi-31 is available in several versions:
• ASMi-31 standalone – the standalone slave unit features a blank panel
• ASMi-31/R – a plug-in card which may be installed in the ASM-MN-214
hub.
• ASMi-31C – a plug-in card which may be installed in the LRS-12 or
LRS-24 hub (see ASMi-31C Installation and Operation Manual for details).
Power Supply Versions
The power supply options are:
• AC power source: 115 VAC or 230 VAC
• DC power source: -48 VDC.
16-03-00 15:51
Overview
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 1. Introduction
ASMi-31 Installation and Operation Manual
Figure 1-1 illustrates the ASMi-31 application.
Application
2-wire
Backbone
HS-U card
ASMi-31
MP-2100
Figure 1-1 ASMi-31 Working Opposite HS-U Card in Megaplex-2100
The ASMi-31 short range modem supports full duplex transmission over
2-wire twisted pair unconditioned lines.
Features
The ASMi-31 modem operates in pairs with either another standalone
modem, or as a card installed in the ASM-MN-214 hub.
A management channel transmitted in-band allows remote configuration for
the modem, real-time alerts on failures, and diagnostic testing. The line data
rate is selectable from 1.2 kbps up to 128 kbps and the line encoding is
2B1Q. ASMi-31 achieves an operating range up to 8 km (5 miles) over
24 AWG wire, independent of data rate.
The ASMi-31 modem is fully compatible with ASM-31 and SRM-31 and
works opposite MP-2100/HS-U module.
The ASMi-31 modem features automatic rate detection in external clock
mode for tail-end applications.
Control Signal Transfers
ASMi-31 supports end-to-end transfer of two control signals: DTR to DSR
and RTS to DCD, except for the V.35 interface or any other standard that
doesn't support this signal (such as X.21, G.703).
Interfaces
ASMi-31 supports the following interfaces: V.24/RS-232, V.35, X.21,
V.36/RS-449, RS-530, G.703 Codirectional, or built-in Ethernet bridge.
Diagnostics
ASMi-31 contains two diagnostic loops for complete diagnostics of both
local and remote modems:
• Local analog loopback
• Remote digital loopback
Both loopbacks are controlled via pins in the DTE interface and are
supported by their respective standards.
1-2
Overview
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 1. Introduction
1.2 Physical Description
ASMi-31 is available as a standalone desktop unit or as a card for the
ASM-MN-214 hub. Figure 1-2 shows the 3D view of the ASMi-31
standalone unit.
Figure 1-2 ASMi-31 Standalone Unit
The front panel includes eight LEDs, which display the status of power, data
flow, control signals and diagnostics. For detailed description of the front
panel, see Chapter 3, Operation.
The back panel includes an power connector with fuse, an interface
connector, and a terminal block with a ground connection for connecting
the telephone lines. The ASMi-31 rear panel is described in greater detail, in
Chapter 2, Installation and Setup.
The internal switches and jumpers can be configured to support a variety of
modes for operating the modem. Refer to Setting the Internal Jumpers in
Chapter 2 for details on jumper location and setting.
1.3 Functional Description
The ASMi-31 standalone modem is managed by a master ASMi-31C modem
card mounted on a LRS-12 or LRS-24 hub. The management channel, which
is transmitted in-band, allows remote configuration, real-time alerts on
system failure, diagnostic testing, and the production of statistical
information on system performance.
General
16-03-00 15:51
Functional Description
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 1. Introduction
ASMi-31 Installation and Operation Manual
The ASMi-31 standalone modem is very conveniently managed from the
master station by means of RADview, a RAD SNMP application. This
user-friendly graphical user interface manages the ASMi-31C modem cards
installed in the LRS-12 or LRS-24 hub and, through them, the ASMi-31
standalone units.
Remote
Management
Both data and management are transmitted inband over the same line,
simultaneously, without interference.
Full duplex operation over 2-wires is achieved using the adaptive
"echo-canceling" technique. The ASMi-31 modem uses 2B1Q line coding
to achieve the range of 8 km/5 miles, for all data rates. This coding
provides immunity to background noise, eliminates normal line distortion
and permits efficient transmission over 2-wire twisted cables.
Data
Transmission
An adaptive equalizer provides noise immunity and high performance over
low quality lines.
The ASMi-31 standalone modem unit has internal jumpers which allow for
special management configurations such as point-to-point applications
without ASMi-31C modem cards in the LRS-12 or LRS-24 hub, and also
on-site diagnostics testing.
Special
Management
Configurations
In addition to the remote diagnostic capability, the ASMi-31 standalone
modem provides diagnostic capabilities which can be executed locally.
These include the Digital Loopback (RLB) and Analog Loopback (LLB)
diagnostics; they are executed via the DTE interface after the appropriate
jumpers are set. The ASMi-31 unit has a blank panel to prevent
unauthorized operation at the customer premises.
Diagnostic
Capabilities
The local diagnostics are as follows:
• Remote Digital Loopback – REM, activated by pin in DTE interface and
supported by respective standard.
• Analog Loopback – Local (ANA defined by the standard as LLB),
activated by pin in DTE interface and supported by the respective
standard.
The ASMi-31 loopbacks do not operate with the X.21 and G.703
(Codirectional) because they are not supported by these standards.
Note
The ASMi-31 modem is coupled to the line through an isolation transformer
which protects against AC or DC overvoltages. The protection circuitry
permits operation even when DC is connected to the line.
Overload
Protection
1-4
Functional Description
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 1. Introduction
1.4 Technical Specifications
Type
2-wire, full duplex unconditioned telephone
line (twisted pair), using echo-cancellation
Line Interface
Line Coding
Range
2B1Q
Up to 8 km (5 miles), over a 24 AWG wire,
independent of data rate
Level
Up to 14 dBm (assuming a 135Ω load)
Connector Type
Standard
3-clip terminal block and RJ-45 connector
Complies with ANSI T1.601.1988
specifications
Types
ITU V.24/RS-232, V.35, RS-530 or X.21,
G.703 Codirectional (64 kbps),
Digital Interface
(DTE)
Ethernet (10BT), Ethernet 10B2 (BNC)
Data Rates
Connectors
1.2 kbps to 128 kbps
• V.24 – 25-pin, D-type female
• V.35 – 34-pin, female
• V.36 – 37-pin, D-type female, via supplied
cable adapter
• X.21 – 15-pin, D-type female
• RS-530 – 25-pin, D-type female
• G.703/TB – Terminal Block
• G.703/RJ – RJ-45, female
• Ethernet (10BaseT) – RJ-45, conforms to
IEEE 802.3
• Ethernet (10Base2) – BNC
16-03-00 15:51
Technical Specifications
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 1. Introduction
ASMi-31 Installation and Operation Manual
Internal clock – The master clock uses its own
internal crystal when transmitting or receiving
data from the DTE interface and from the line.
Master Clock
Clock Source
External clock – The master clock uses the
clock derived from the digital interface to
receive data from the DTE and for transmitting
data to the line.
If the digital interface is X.21, the same clock is
used to transmit and receive data.
Loopback timing – The clock is recovered
from the line signal and used to transmit and
receive data from the DTE interface to the
line.
Slave Clock
Jumper-selectable:
• RTS to DCD
• DTR to DSR
Remote Digital Loopback – REM activated by
pin in DTE interface supported by the
appropriate standard
Control Signals
Diagnostics
Loopback Tests
Analog Loopback – Local (ANA defined by
the standard as LLB) activated by pin in DTE
interface supported by the appropriate
standard
PWR (green)
RTS (yellow)
TD (yellow)
RD (yellow)
DCD (yellow)
LOS (red)
Power
Indicators
Request To Send (Circuit 105)
Transmit Data (Circuit 103)
Receive Data (Circuit 104)
Data Carrier Detect (Circuit 109)
Loss of signal
ERR (red)
Error is detected in received configuration
information
TEST (red)
A test is active
AC Voltage
Frequency
DC Voltage
Power Fuses
115 VAC or 230 VAC (10%), 5W
50 or 60 Hz (47 to 63 Hz)
-48 VDC (-36 to -72 VDC)
0.1A, slow-blow for 230V
Power
1-6
Technical Specifications
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 1. Introduction
0.2A, slow-blow for 115V
4.4 cm / 1.7 in
Height
Width
Depth
Weight
Physical
19.3 cm / 7.6 in
24.3 cm / 9.6 in
1.5 kg / 3.3 lb
Temperature
Humidity
0°-50° C / 32°-122° F
Environment
Up to 90%, non-condensing
16-03-00 15:51
Technical Specifications
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 1. Introduction
ASMi-31 Installation and Operation Manual
1-8
Technical Specifications
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 2
Installation and Setup
This chapter provides the following information for the ASMi-31 standalone
model:
• Site requirements and prerequisites
• Package contents
• Instructions for mechanical installation
• Instructions for electrical installation.
After installing the unit, refer to Chapter 3 to assure normal operation.
In case a problem encountered, refer to Chapter 4 for test and diagnostic
instructions.
Refer to Chapter 5 for additional information on the ASMi-31/R card
version.
2.1 Site Requirements and Prerequisites
AC-powered ASMi-31 units should be installed within 1.5m (5 ft) of an
easily accessible grounded AC outlet. The outlet should furnish 115 VAC or
230 VAC.
Power
DC-powered ASMi-31 units require -48 VDC power source, which must be
adequately isolated from the mains supply.
• Allow at least 90 cm (36 in) of clearance at the front for operating and
maintenance accessibility.
• Allow at least 10 cm (4 in) clearance at the rear of the unit for signal lines
and interface cables.
The ambient operating temperature of ASMi-31 is 0 to 50°C (32 to 122°F)
at relative humidity of 90%, non-condensing.
Ambient
Requirements
16-05-01 13:37
Site Requirements and Prerequisites
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 2. Installation and Setup
ASMi-31 Installation and Operation Manual
2.2 Package Contents
• One ASMi-31 unit (protected by adequate cushioning)
• AC power cord or DC power supply connector kit
• ASMi-31 Installation and Operation Manual
• Interface adapter cable(s) (see Table 2-2) - Optional.
2.3 Installation and Setup
ASMi-31 is a standalone device intended for tabletop or bench installation.
It is delivered completely assembled. No provisions are made for bolting
ASMi-31 to the tabletop. For installation of the unit in a 19" rack, refer to
Appendix F.
➤ To complete the installation of ASMi 31:
1. Determine the required configuration of the modem according to your
application, and set the internal jumpers and switches accordingly (see
and .
2. Connect the line (see Connecting the Line below).
3. Connect the DTE interface (see Connecting the DTE below).
4. Connect power to the unit (see Connecting the Power below).
This section provides information on the functions of the internal jumpers
and switches, to help you in the selection of the correct settings for
particular application, and gives you step-by-step instructions for
performing the internal settings. The default settings are also listed.
Setting the
Internal Jumpers
1. Open the ASMi-31 case.
2. Set the ASMi-31 internal jumpers and switches, referring to Figure 2-1
and Table 2-1.
3. Reinstall the ASMi-31 cover.
2-2
Installation and Setup
16-05-01 13:37
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 2. Installation and Setup
Access to the inside of the equipment is permitted only to the
authorized and qualified personnel.
Warning
To avoid accidental electric shock, always disconnect the interface
cables and the power cord before removing the unit from its casing.
Line voltages are present inside ASMi-31 when it is connected to power
and/or the lines. Moreover, under certain fault conditions, dangerous
voltages may appear on the lines connected to the unit.
Any adjustment, maintenance and repair of the opened instrument
under voltage must be avoided as much as possible and, when
inevitable, should be carried out only by a skilled technician who is
aware of the hazard involved. Capacitors inside the unit may still be
charged even after the unit has been disconnected from its source of
power.
ASMi-31 contains components sensitive to electrostatic discharge (ESD). To
prevent ESD damage, avoid touching the internal components, and before
moving jumpers, touch the ASMi-31 frame.
Caution
Opening the ASMi-31 Case
To reach the internal jumpers and switches of ASMi-31, it is necessary to
open its case.
➤ To open the ASMi-31 case:
1. Disconnect all the cables connected to ASMi-31.
2. Turn the unit over (bottom facing up).
3. Unscrew the four cover screws.
4. Turn the unit over (bottom facing down).
5. After the four screws released, remove the ASMi-31 top cover by
pulling it straight up.
Setting the Internal Jumpers and Switches
The internal jumpers and switches located on the ASMi-31 printed circuit
board (PCB) are identified in * Baud rates not applicable.
Figure 2-1. Their numbers under heading "Item" in Table 2-1 correspond to
the identification numbers shown in Table 2-1.
16-05-01 13:37
Installation and Setup
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 2. Installation and Setup
ASMi-31 Installation and Operation Manual
CHASS-GND
CON
2
1
DIS
3
JP15
CLOCK
LBT
4
INT
EXT
B
POS BAUD
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0.6K
5
1.2K
2.4K
4.8K
9.6K
19.2K
38.4K
48K
*56K
64K
SLAV
DSR
DCD
1STB
EVEN
P.EN
8BIT
MAST
DTR
CNT
2STB
ODD
DIS
128K
*144K
*57.6K
*115.2K
16K
7BIT
SYNC
ASY
32K
6
* Baud rates not applicable.
Figure 2-1 ASMi-31 PCB Layout
Table 2-1 ASMi-31 Internal Jumpers and Switches
Item Jumper
Description
Values
Default Setting
DIS – The RLB activation from
the DTE is disabled
EN – The RLB activation from
the DTE is enabled
1
RLB, JP14
Controls the remote loopback
activation from the DTE
DIS
CON – Signal ground is
connected to the frame ground
DIS – Signal ground is
disconnected from the frame
ground
2
CHASS-GND, Controls the connection
CON
JP18
between the ASMi-31 signal
ground and the frame (chassis)
ground
Note: Disconnecting the signal ground from the frame ground may render the unit unsafe for connection to
unprotected telecommunication networks in some locations.
2-4
Installation and Setup
16-05-01 13:37
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
ASMi-31 Installation and Operation Manual
Chapter 2. Installation and Setup
Table 2-1 ASMi-31 Internal Jumpers and Switches (Cont.)
Item Jumper
Description
Values
Default Setting
3
LLB, JP15
Controls the local loopback
activation from the DTE
DIS – The LLB activation from DIS
the DTE is disabled
EN – The LLB activation from
the DTE is enabled
4
CLOCK
Controls the ASMi-31 timing
reference
LBT – Loopback timing, clock is LBT
recovered from the data at the
line side
INT – Internal clock
EXT – External clock
1 – 1.2 kbps, sync/async
2 – 2.4 kbps, sync/async
3 – 4.8 kbps, sync/async
4 – 9.6 kbps, sync/async
5 – 19.2 kbps, sync/async
6 – 38.4 kbps, sync/async
7 – 48 kbps, sync
5
SW7
Selects the data rate
9 – 64 kbps, sync
A – 128 kbps, sync
E – 16 kbps, sync
F – 32 kbps, sync
9 – 64 kbps
5
SW6
DIP switch, which consists of eight section
Section 1
Controls the ASMi-31 operation ON – Async operation
mode – synchronous or
OFF – Sync operation
Sync
asynchronous
Section 2
Section 3
Section 4
Section 5
Section 6
Defines the number of data bits ON – 8 bits
8 bits
to be used
OFF – 7 bits
Controls the use of parity
Defines the parity type
ON – Parity enabled
P.EN
Even
1STB
DCD
OFF – Parity disabled
ON – Even parity
OFF – Odd parity
Defines the number of stop bits ON – One stop bit
OFF – Two stop bits
Controls the RTS to DCD
transfer
ON – DCD, the DCD signal
turns on when the two units
reach synchronization
OFF – CNT, the DCD signal of
the local unit follows the RTS
signal of the remote unit
Note: The DCD signal is OFF when a digital loopback is active (receiving RLB command) or when there is no
synchronization between the units).
16-05-01 13:37
Installation and Setup
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 2. Installation and Setup
ASMi-31 Installation and Operation Manual
Table 2-1 ASMi-31 Internal Jumpers and Switches (Cont.)
Item Jumper
Description
Values
Default Setting
Section 7
Controls the DTR to DSR
transfer
ON – Indicates only that the
local unit is powered up. It
does not indicate the status of
the communication channel or
operational status of the remote
site
DSR
OFF – Indicates that the DSR of
the local unit follows the DTR
signal of the remote unit
Section 8
Controls the ASMi-31
operational status – slave or
master
ON – Slave
Slave
OFF – Master
Closing the ASMi-31 Case
After completing the internal settings, close the unit case.
➤ To close the ASMi-31 case:
1. Replace the upper half of the unit and press firmly until the plastic tabs
fit into the tab housing.
2. Insert the original cover screws in their positions and tighten carefully.
Do not use excessive torque.
Figure 2-2 illustrates the rear panel of the ASMi-31 modem.
Connecting the
Interfaces
DTE
LINE
GND
2
45
~230V
0.1A T 250V
Figure 2-2 ASMi-31 Rear Panel
Connecting the Line
The ASMi-31 line connector is a terminal block/RJ-45 connector. Connect
the transmission line (twisted pair) to the two clips marked LINE and the
cable shield to the clip marked GND (optional). High rate data
communication twisted pair cable is highly recommended in order to
prevent crosstalk.
Before connecting the cables, make sure that the equipment is earthed by
its power cable.
Insert the GND lead first.
Caution
2-6
Installation and Setup
16-05-01 13:37
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 2. Installation and Setup
➤ To connect the line:
1. Insert the screwdriver into a square hole (see Figure 2-3).
Figure 2-3 Connecting the Line – Step 1
2. Raise the inserted screwdriver, putting pressure on the ramp within the
square hole (see Figure 2-4).
Figure 2-4 Connecting the Line – Step 2
3. Insert the stripped end of the wire and remove the screwdriver (see
Figure 2-5).
Figure 2-5 Connecting the Line – Step 3
Connecting the DTE
The rear-panel DTE connector provides interface for data input/output,
clock reference and control signal exchange between ASMi-31 and the DTE.
The DTE interface is changeable module with the interface connector. The
DTE is connected to ASMi-31 via adapter cables depending on the interface
type, see Table 2-2 to select the correct cable for your DTE interface.
Table 2-2 DTE Interfaces and Matching Adapter Cables
DTE Interface
V.24/RS-232
V.35
Connector Description
25-pin, D-type, female
34-pin, female
RAD Cable
CBL-HBT/V24
CBL-HBT/V35
CBL-HBT/X21
X.21
15-pin, female
16-05-01 13:37
Installation and Setup
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 2. Installation and Setup
ASMi-31 Installation and Operation Manual
Table 2-2 DTE Interfaces and Matching Adapter Cables (Cont.)
DTE Interface
Connector Description
RAD Cable
RS-530/RS-449
25-pin, D-type connector. For a description of the
cabling connection between the RS-530 interface and
the RS-449/RS-442 (V.36) 37-pin, D-type connector,
see Appendix E. The cable is provided with the
product.
CBL-HBT/RS-530
G.703
Codirectional 64 kbps interface. For a description of
the G.703, see Appendix B.
Ethernet Interface
RJ-45 or BNC connector. For a description of the
Ethernet interface, see Appendix A.
Connecting the Power
The AC power is supplied to the ASMi-31 unit through the 1.5m (5 ft)
standard power cable terminated in a standard 3-prong plug (see Figure 2-
2). The cable is provided with the unit.
The rated fuse for the unit is 250V / 0.1A slow-blow for 230V, or
250V / 0.2A slow-blow for 115V.
The unit has no power switch. Operation starts when the power is
applied to the rear-panel POWER connector.
Warning
Before switching on this instrument, the protective earth terminals of
this instrument must be connected to the protective ground conductor
of the power cord. The power plug shall only be inserted in a power
outlet provided with a protective earth contact. The protective action
must not be negated by use of an extension cord (power cable) without
a protective conductor (grounding).
Make sure that only fuses with the required rated current, as marked on
the ASMi-31 rear panel, are used for replacement. The use of repaired
fuses and the short-circuiting of the fuse holders is forbidden.
Whenever it is likely that the protection offered by fuses has been
impaired, the instrument must be made inoperative and be secured
against any unintended operation.
➤ To connect AC power to ASMi-31:
1. Connect the power cable to the connector on the ASMi-31 rear panel.
2. Connect the power cable to the mains outlet.
The unit will be turned on automatically upon connection to the
mains.
➤ To connect DC power to ASMi-31:
• Refer to DC Power Connection Supplement.
2-8
Installation and Setup
16-05-01 13:37
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 3
Operation
This chapter provides the following information for the ASMi-31 standalone
modem:
• ASMi-31 front-panel indicators and controls
• Operating procedures (turn-on, front-panel indications, performance
monitoring and turn-off).
Installation procedures given in Chapter 2 must be completed and checked
before attempting to operate ASMi-31.
3.1 Controls and Indicators
Figure 3-1 illustrates the ASMi-31 standalone modem front panel. Table 3-1
lists the functions of the controls and indicators.
PWR RTS TD
RD DCD LOS ERR TEST
RESET
Figure 3-1 ASMi-31 Front Panel
In ASMi-31 modem/X.21 RTS LED is equivalent to Control signal (C), and
DCD LED is equivalent to Indication signal (I).
Note
Table 3-1 Front Panel Controls and Indicators
Name
Type
ITU Circuit
Function
RESET
Button
This switch resets the unit; it is used in place of a power switch.
It is not needed for normal operation.
PWR
RTS
Green LED
Yellow LED
On when ASMi-31 is powered up.
105
103
On when the DTE has emitted an active Request to Send signal
(or Control in X.21).
TD
RD
Yellow LED
Yellow LED
On when a steady space is being transmitted.
Blinks when data is transmitted.
104
On when a steady space is being received.
Blinks when data is received.
16-03-00 15:51
Controls and Indicators
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 3. Operation
ASMi-31 Installation and Operation Manual
Table 3-1 Front Panel Controls and Indicators (Cont.)
Name
Type
ITU Circuit
Function
DCD
Yellow LED
109
On when the local and remote modems are in sync, and the
section 6 of the internal SW6 switch is set to ON.
On when the local and remote modems are in sync, and the
section 6 of the internal SW6 switch is set to OFF, and the RTS at
the remote modem is ON.
LOS
ERR
Red LED
Red LED
Red LED
On when loss of synchronization occurs between the local and
remote modem.
On when an error occurs in the configuration received from the
master unit.
TEST
On when a test is active.
3.2 Operating Instructions
ASMi-31 turns on as soon as power is connected. When power is
connected, the PWR indicator lights up and remains lit as long as ASMi-31
receives power.
Turning ASMi-31
On
Check that the other front panel LEDs appear as listed in Table 3-2. This
indicates that the local and remote ASMi-31 units are operational and
passing data.
Normal LEDs
Indications
Table 3-2 ASMi-31 Controls and Indicators – Normal Operation
Name
State
Function
PWR
TD
RD
RTS
DCD
On
On or blinking
Off or blinking
Flashing depends upon the data being transmitted.
Flashing depends upon the data being received.
Lights when RTS status is On
Lights when RTS is received from the remote
modem and the modems are synchronized
(DCD - OFF - switch SW6)
LOS
On or blinking
Blinks until synchronization between the modems
is achieved.
Constantly On when there is no synchronization.
Blinks until synchronization between the modems
is achieved.
Blinks until synchronization between the modems
is achieved.
ERR
Off or blinking
On or blinking
TEST
Constantly On while test is activated from either
local or remote unit.
3-2
Operating Instructions
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 3. Operation
If the above LED indicators are not obtained following initial power-up,
make sure that:
• One modem is set to internal or external clock, and the other to LBT
clock.
• None of the modems are in test mode.
To turn off ASMi-31, simply remove the power cord from the power source.
Turning ASMi-31
Off
16-03-00 15:51
Operating Instructions
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 3. Operation
ASMi-31 Installation and Operation Manual
3-4
Operating Instructions
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 4
Troubleshooting and
Diagnostics
This chapter describes how to perform diagnostics tests on ASMi-31.
The function of diagnostic tests on ASMi-31 is to:
• Check that the system is operating normally
• Isolate faulty equipment or cables
• Identify other sources of system malfunction.
Tests are activated via the corresponding DTE pins and monitored via the
ASMi-31 front-panel LED indicators.
4.1 Diagnostic Tests
The diagnostic capabilities of the ASMi-31 modem allow rapid checkout of
the DTEs, the ASMi-31 modem, and connecting lines. The test will
immediately verify the operational performance of each unit in the system
or provide an indication of equipment failure.
Before testing the operation of the data system equipment and 2-wire line
circuits, first ensure that all units are powered on and configured normally,
then perform the test steps described below, in order.
ASMi-31 supports two types of loopback tests for evaluating the operation of
the data system equipment and line circuits. Using these loopbacks, you can
test the communication between the attached equipment, internal circuitry
of the local ASMi-31 and the remote ASMi-31.
24-01-00 19:17
Diagnostic Tests
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 4. Tests and Diagnostics
ASMi-31 Installation and Operation Manual
The Local Analog Loopback (LLB) test checks the performance of the local
ASMi-31, the local DTE, and the connections between them (see
Figure 4-1). Perform the test separately at the local and the remote site.
Local Analog
Loopback (LLB)
Data
Clock
Transmit
Receive
Line
Interface
DTE
Clock
Data
ASMi-31
Figure 4-1 Local Analog Loopback
➤ To perform the Local Analog Loopback test:
• Activate the test via the DTE interface analog loopback.
The TEST LED lights up.
The ASMi-31 modem transmit output is connected to the receiver circuits
internally at the line side. If a fault is indicated, call a technician or replace
the unit.
Set the DTE equipment in half duplex (which produces an "echo" through
the system). It is recommended that you repeat the LLB test using an
external Bit Error Rate Tester (BERT).
Perform the test at both ends. If the BERT equipment test indicates no faults,
but the data terminal indicates a fault, follow the DTE manufacturer's test
procedures . Also check the interconnecting cable interfacing between the
terminal and the ASMi-31 modem.
After completing the test (or when the fault has been corrected), deactivate
the LLB via the DTE interface and proceed to the Remote Loopback
(Communication Link) Test.
4-2
Diagnostic Tests
24-01-00 19:17
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 4. Tests and Diagnostics
This test determines the performance of both the local and the remote
ASMi-31 modems, as well their connecting 2-wire line between them. The
test activates a diagnostic loopback at the remote ASMi-31 modem (see
Figure 4-2).
Remote Loopback
(RLB)
Data
Transmit
Receive
Clock
Link
Interface
Link
Interface
Remote
DTE
Local
DTE
Clock
Data
Receive
Local ASMi-31
Transmit
Remote ASMi-31
Figure 4-2 Remote Digital Loopback
➤ To activate the Remote Digital Loopback:
• Activate the Remote Loopback via the DTE interface.
The TEST LED lights on both units.
Set the DTE equipment in half duplex (which produces an "echo" through
the system), or run a Bit Error Rate test.
Perform the test at both ends. If the BER test indicates a fault and if the LLB
test was successful for both local and remote modems, then the 2-wire line
circuits inside the modem are not operating properly, or the line connection
between the modems is faulty.
24-01-00 19:17
Diagnostic Tests
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 4. Tests and Diagnostics
ASMi-31 Installation and Operation Manual
4-4
Diagnostic Tests
24-01-00 19:17
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 5
Card Cage Version
This chapter describes the ASMi-31/R card version, designed for installation
in the ASM-MN-214 card cage. The chapter contains the following sections:
• Section 5.1 describes the ASM-MN-214 card cage
• Section 5.2 describes the ASMi-31/R card version
• Section 5.3 describes the power supply to ASMi-31/R
• Section 5.4 describes how to install ASMi-31/R.
5.1 ASM-MN-214 Card Cage
The ASM-MN-214 card cage contains one or two power supplies and up to
14 plug-in cards. The card types can be ASMi-31/R or other RAD rack
version modems/converters - any combination of up to 14 plug-in cards.
For each of the 14 cards, the rear panel (see Figure 5-1) contains a male
connector for the terminal block and a DB-25 connector. A protection cover
protects the terminal block connectors.
The terminal block (see Figure 5-1) is to be attached to the rear panel
terminal block connectors. It contains screws for connecting the transmit
and receive pairs and ground, if present.
The 25-pin D-type female interface connector provides all interface signals
for the digital interfaces. Modems with X.21 or V.35 interface require an
external mechanical adapter.
Two optional interface attachments, CIA/V.35/1 and CIA/X.21, can be
ordered separately from RAD. CIA/X.21 converts two adjacent DB-25
connectors to two X.21 15-pin connectors. CIA/V.35/1 converts one DB-25
connector to a V.35 34-pin connector.
V.36 modem cards are supplied with a RAD adapter cable CBL 530/449F,
which converts the DB-25 connector to a V.36 37-pin connector. The
adapter cable and two interface attachments are also shown in Figure 5-1.
16-03-00 15:51
ASM-MN-214 Card Cage
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Chapter 5. Card Cage Version
ASMi-31 Installation and Operation Manual
Terminal
Block
Terminal
Block
CIA/V.35/1
Protection
Cover
CIA/X.21
CBL-530/449
Figure 5-1 ASM-MN-214 Rear Panel
5-2
ASMi-31/R Card Version
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 5. Card Cage Version
5.2 ASMi-31/R Card Version
Figure 5-2 shows the ASMi-31/R card front panel. The LEDs and switches of
the card version are identical in their functionality to those of the standalone
device. For this information, refer to Section 3.1, Controls and Indicators, in
Chapter 3.
The jumper settings are the same as with ASMi-31 standalone version (refer
to Table 2-1).
PWR
RTS
TD
RD
DCD
LOS
ERR
TEST
RESET
ASMi-31
Figure 5-2 ASMi-31/R Front Panel
16-03-00 15:51
Power Supply
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 5. Card Cage Version
ASMi-31 Installation and Operation Manual
5.3 Power Supply
Power is supplied to the ASMi-31/R card from the ASM-MN-214 power
supply via the chassis. Each ASMi-31/R card has two fuses, which protect the
entire system against power failure resulting from a short circuit in one card.
The ASM-MN-214 card cage can accept both AC or DC power supplies.
LED indicators located on the ASM-MN-214 front panel (see Figure 5-3)
show activity when the power supply is connected to the mains plug. The
power supply supports the full card cage with any combination of cards.
The AC power supply of the ASM-MN-214 is 100, 115 or 230 VAC, 10%,
47 to 63 Hz.
AC Supply (100,
115 or 230 VAC)
The DC power supply is - 48 VDC (-36 to -72 VDC). It uses a DC/DC
converter module to provide the power required for the cards.
DC Supply
(-48 VDC)
Power Supply
with Redundancy
This special ordering option is equipped with two separate power supplies,
operating together and sharing the load of the whole card cage. If either of
the power supplies fails, the other one will continue to supply power to the
full card cage.
Two LED indicators show activity of each power supply. They should both
light when mains power is provided.
Note
It is possible to combine AC and DC power supplies in the same cage.
Figure 5-3 ASM-MN-214 Front Panel
5-4
Installing ASMi-31/R
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Chapter 5. Card Cage Version
5.4 Installing ASMi-31/R
➤ To install the ASMi-31/R card in the ASM-MN-214 card cage:
1. Install the ASM-MN-214 card cage in the 19" rack.
2. Adjust the jumpers and switches on the card as required (see Figure 2-
1 and Table 2-1 in Chapter 2).
3. Insert the ASMi-31/R card into one of the ASM-MN-214 slots. Push the
bottom of the card into the cage to until it is fully inserted into the edge
connector inside the rack. Tighten the screws on the top and on the
bottom of each card.
4. Remove the protection cover from the terminal block connectors.
5. Connect the terminal block to the ASM-MN-214 terminal block
connector.
6. Connect the line to the terminal block as follows: connect transmit pair
to the terminals marked XMT, the receive pair to the terminals marked
RCV, and the fifth screw to ground (optional).
7. If required, attach the appropriate CIA (CIA/X.21 or CIA/V.35/1) or V.36
adapter cable to the DB-25 connector on the card cage rear panel.
8. Connect the DTE cable to the DB-25 connector, other side of CIA or
adapter cable (depending on your version of the card interface).
9. Connect power to the ASM-MN-214 card cage:
• To connect AC power, connect the power cable to the mains supply.
• To connect DC power, refer to DC Power Supply Connection
Supplement of the ASM-MN-214 manual.
The ASM-MN-214 card cage has no power switch. Operation starts
when the power is applied to the rear panel POWER connector. When
applying power, first connect the plug of the power cord to the
ASM-MN-214 POWER connector and then to the mains power source
(outlet).
Warning
16-03-00 15:51
Installing ASMi-31/R
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Chapter 5. Card Cage Version
ASMi-31 Installation and Operation Manual
5-6
Installing ASMi-31/R
16-03-00 15:51
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Appendix A
Ethernet Interface
A.1 General
This appendix:
• Describes the IR-ETH for RAD modems
• Describes the different IR-ETH connector options
• Lists the Ethernet bridge specifications
• Explains how to install and operate an Ethernet bridge.
A.2 Description
The IR-ETH is an interface module for RAD modems, used for converting
the Ethernet (10BaseT or 10Base2) electrical levels to the modem TTL levels.
It also converts the Ethernet protocol to HDLC to enable long distance
transmission and avoid the Ethernet collision limitation.
The IR-ETH includes an internal, self-learning Ethernet bridge, which
enables a high performance link between two Ethernet segments at a low
transmission rate. The low-speed HDLC transmission is sent over the link
using the modem modulation technique. It is converted back to an Ethernet
signal at the remote modem.
Figure A-1 shows a typical application using an Ethernet interface bridge.
Each modem is connected to an Ethernet network via the Ethernet Interface
bridge.
LINK
MODEM
MODEM
Figure A-1 Ethernet Interface Typical Application
Description
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix A. Ethernet Interface
ASMi-31 Installation and Operation Manual
A.3 IR-ETH Connector Options
Figure A-2 and Figure A-3 show the rear panel of ASMi-31 with the IR-ETH
connector options. The IR-ETH connector for the ASMi-31/R card
(rack mount version) is shown in Figure A-4.
Line Connector
Figure A-2 ASMi-31 Rear Panel with IR-ETH/UTP Connector Option
Line Connector
Figure A-3 ASMi-31 Rear Panel with IR-ETH/BNC Connector Option
13
12
11
(13) RCV(+)
(12) RCV(-)
(11) XMT(+)
(9) XMT(-)
(7) GND
9
7
DB-25
Figure A-4 IR-ETH Connector for the ASMi-31/R Modem Card
A-2
IR-ETH Connector Options
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Appendix A. Ethernet Interface
When using the RJ-45 connector, the customer must prepare a mechanical
cable for adapting the DB-25 pinout to that of RJ-45. The pinouts of the
DB-25 and RJ-45 connectors are given in Table A-1.
Table A-1 DB-25 and RJ-45 Pin Assignment for IR-ETH Connection
Signal
Pin
DB-25
13
RJ-45
RCV (+)
3
6
1
2
-
RCV (-)
XMT (+)
XMT (-)
GND
12
11
9
7
A.4 Ethernet Bridge Specifications
LAN Table
10,000 addresses
15,000 pps
General
Filtering and
Forwarding
Buffer
256 frames
1 frame
Delay
Standard
Data Rate
Connectors
Conforms to IEEE 802.3/Ethernet
10 Mbps (20 Mbps 10BaseT FDX)
LAN
10BaseT (UTP): Shielded RJ-45
10Base2: BNC connector
Protocol
HDLC
WAN
Data Rate
According to the modem transmission rate
Installation and Operation
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix A. Ethernet Interface
ASMi-31 Installation and Operation Manual
A.5 Installation and Operation
Figure A-5 and Figure A-6 show the Ethernet bridge layout, the locations of
the DIP switches, and the rear panel components for the UTP and the BNC
versions, respectively.
4
3
2
1
Figure A-5 Ethernet Bridge Layout (UTP Option)
4
3
2
1
Figure A-6 Ethernet Bridge Layout (BNC Option)
A-4
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Appendix A. Ethernet Interface
For 10BaseT installation, either a straight cable or a cross-cable may be
required. Use a cross-cable when connecting to a port that does not
implement the crossover function internally. Otherwise, use a straight cable.
LAN Installation
Hubs usually implement the crossover function internally while NICs and other
devices do not.
Note
Set switches according to Table A-2.
Switch Settings
Table A-2 DIP Switches Settings
Switch
Number
Name
SQ/FD
CMP
FIL
Description
Default
Setting
1
2
3
4
ON: Ethernet full-duplex mode
OFF: Ethernet half-duplex mode
OFF
ON
ON
OFF
ON: Strips padding bits inserted in 64-byte frame
OFF: Transmits frames over WAN as is
ON: Passes only frames destined for another LAN
OFF: Disables LAN filter; passes all frames transparently
(nc)
The SQ/FD switch is not used in the Ethernet bridge with the BNC connector
option.
Note
Table A-3 lists the IR-ETH LED indicators and describes their functions.
LED Indicators
Table A-3 IR-ETH Bridge LED Indicators
LED Name
Description
Location
Color
LINK
ON indicates good link integrity (available only in
the 10BaseT version)
Panel
Green
COLL
RX
ON indicates collision on the attached Ethernet
segment
Panel
Yellow
Yellow
Yellow
Red
ON when data is received from the Ethernet
attached segment
Panel
TX
ON when data is transmitted from the modem to
the Ethernet segment
Panel
ERR D4
Bridge buffer overrun
On board
Installation and Operation
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix A. Ethernet Interface
ASMi-31 Installation and Operation Manual
A-6
Installation and Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Appendix B
IR-G.703 Codirectional
Interface (64 kbps)
B.1 Introduction
This appendix:
• Provides a general description of the IR-G.703 Codirectional interface
(64 kbps)
• Describes the EXT mode for the IR-G.703 Codirectional interface
(64 kbps)
• Describes the INT/RCV mode for the IR-G.703 Codirectional interface
(64 kbps).
B.2 General Description
The IR-G.703 is an interface module for RAD modems, converting G.703
Codirectional signals to TTL levels. The converted data is sent over the
modem link using the modem modulation technique and converted back at
the other end into G.703 64 kbps Codirectional signals, or into any other
digital interface signal possible. The module is available in the following two
versions:
• The Standalone version fits into a standalone modem and is available
with two types of physical connections: a terminal block or an RJ-45.
• The Rack version is mounted on the rack version modem card and uses
the modem edge connector for communication. The edge connector is
wired, on the motherboard of the card cage, to the DB-25 connector on
the back plane of the ASM-MN-214 card cage. Figure B-1 illustrates the
pinout of the different connectors.
16-03-00 17:21
General Description
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix B. IR-G.703 Codirectional Interface (64 kbps)
ASMi-31 Installation and Operation Manual
(9,11) RCV
2
(2,16) XMT
RCV (3, 6)
GND (2)
XMT
(4, 5)
(7) GND
7
1
8
G.703
LINE FUSE
LINE
9
11
GND
2
4 5
16
GND XMT RCV
230 V/0.1A T 250V
Terminal Block
(Standalone)
RJ-45
(Standalone)
DB-25
(Rack Version)
Figure B-1 IR-G.703 Connector Options
In Figure B-1, RCV refers to the input signals to the interface module;
XMT refers to the output signals from the module.
Note
The IR-G.703 interface module is shown in Figure B-2. It has two operation
modes which are selectable on the PCB board. The selection is made by
means of the JP1 jumper located within the module as shown in Figure B-2.
The EXT mode is described in EXT Mode below and illustrated by Figure B-3.
The INT/RCV mode is described in INT/RCV Mode below and illustrated by
Figure B-4.
The IR-G.703 interface should be in accordance with the modem clock
mode. For example, if the modem is in the EXT mode, then JP1 should be set
to the EXT position.
Note
INT/RCV
JP1
Terminal Block
or RJ-45
(Standalone Version)
EXT
Figure B-2 Location of JP1 on the IR-G.703 Interface Module
B.3 EXT Mode
This mode is used in applications, where the system timing is provided by
the G.703 network. The IR-G.703 module has an internal buffer to
compensate for the phase delay introduced to the system by the line delay
between the two modems. The buffer is an 8-bit FIFO connected as shown
in Figure B-3.
This mode corresponds to the modem clock working in the EXT mode.
B-2
EXT Mode
16-03-00 17:21
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Appendix B. IR-G.703 Codirectional Interface (64 kbps)
Modem A
Modem B
IR-G.703 Module
TX Data
TX
RX
RX
TX
Data
CLK
Clock
Recovery
G.703
Codirectional
Clock
Out
FIFO
Data
64 kbps network
Clock
Recovery
Clock
Recovery
RX Data
Timing Source
Clock In
FIFO
EXT Clock Mode
RCV Clock Mode
Figure B-3 IR-G.703 EXT Mode Timing Block
B.4 INT/RCV Mode
This mode is used in applications where the G.703 Codirectional 64 kbps
equipment connected to the modem recovers the clock signal from the
modem link. This mode is used mainly when the attached equipment has a
G.703 Codirectional interface, but is not able to produce clock signals. The
module has a 8-bit FIFO buffer to compensate for the phase delay
introduced by the G.703 device. Figure B-4 illustrates the buffer connection
and the required application setup.
This mode corresponds to the modem clock working in the INT or RCV
mode.
Modem A
Modem B
DTE
side
LINK
side
G.703
side
IR-G.703 Module
RX Data
TX
RX
Data
CLK
Clock
Recovery
EXT, INT or RCV
Clock Mode
(Depending on the
attached network)
INT or RCV
Clock Mode
Equipment
with G.703
interface
Clock
Out
FIFO
TX Data
Data
RX TX
Clock
Recovery
Clock In
FIFO
INT/RCV Clock Mode
Figure B-4 IR-G.703 INT/RCV Mode Timing Block
16-03-00 17:21
INT/RCV Mode
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix B. IR-G.703 Codirectional Interface (64 kbps)
ASMi-31 Installation and Operation Manual
B-4
INT/RCV Mode
16-03-00 17:21
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Appendix C
X.21 Interface Module
C.1 General
IR-X.21 is an interface module for RAD modems, converting X.21 signals to
TTL levels. The converted data is sent over the modem link, using the
modem modulation technique, and is converted back at the other end into
X.21 signals, or into any other digital interface signal.
ASMi-31 is generally supplied with IR-X.21. This is due to an internal FIFO
that assumes the phase mismatch when the clock is supplied by an external
source. ASMi-31 also has the option to order IR-X.21 for extra buffers.
Figure C-1 shows a typical application of the ASMi-31 standalone modem
with the IR-X.21 interface module.
Figure C-1 Typical ASMi-31 X.21 Application
C.2 X.21 Connectors
Figure C-2 shows the rear panel of a standalone ASMi-31 with the
IR-X.21 interface module.
Line Connector
Figure C-2 ASMi-31 Rear Panel with X.21 Connector
The ASMi-31 modem rack version requires an additional adaptor to connect
between the DB-15 connector of the X.21 equipment to the DB-25
connector of the ASM-MN-214 modem rack. For this purpose, an optional
DB-15 attachment CIA/X.21 can be ordered separately from RAD. The
attachment connects to the ASM-MN-214 rear panel as shown for the
CIA/V.35 attachment in Chapter 5.
X.21 Connectors
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix C. X.21 Interface Module
ASMi-31 Installation and Operation Manual
Table C-1 shows the X.21 DB-15 pin assignment.
Table C-1 IR-X.21 DB-15 (RS-422) Connector Pin Assignment
Pin Assignment
Pin
1
ID
Function
Shield
Chassis connection
Transmit signal A
Control A
2
A
3
A
4
A
Receive A
5
A
Indication A
Signal timing A
External Timing
Common
6
A
7
A
8
GND
B
9
Transmit B
10
11
12
13
14
15
B
Control B
B
Receive B
B
Indication B
Signal Timing B
External Timing
Not connected
B
B
C-2
X.21 Connectors
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Appendix C. X.21 Interface Module
INT/RCV
clock setting
JP 2
EXT
clock setting
Connector DB-15
Figure C-3 Location of Jumper JP2 in the IR-X.21 Interface Module
C.3 EXT Mode
This mode is used in applications of X.21 networks where the system timing
is provided by the X.21 network. The IR-X.21 module has an internal buffer
to compensate for the phase delay introduced to the system by the line
delay between the two modems. The buffer is a 16-bit FIFO connected as
shown in Figure C-4. When the modem's clock mode is EXT, the JP2 jumper
must be set to EXT (see Figure C-3).
EXT Mode
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix C. X.21 Interface Module
ASMi-31 Installation and Operation Manual
IR-X.21B
TXD
ETC
TXD
(2, 9)
Signal Timing
(6, 13)
DTE
ETC
MODEM
RXC
(7, 14)
FIFO
Buffer
Rx
RXD
RXD
(4, 11)
Figure C-4 EXT Mode Timing Block
C.4 INT/RCV Mode
This mode is used in applications where the IR-X.21 side uses the clock
signal from the modem link. This mode is used mainly when the attached
equipment has an IR-X.21 interface, but no ability to produce clock signals.
The module has a 16-bit FIFO buffer to compensate for the phase delay
introduced by the X.21 device. Figure C-5 illustrates the buffer connection
and the required application setup. When the modem's clock mode is INT
or RCV, the JP2 jumper must be set to INT/RCV (see Figure C-3).
IR-X.21B
TXD
TXC
TXD
(2, 9)
Signal Timing
(6, 13)
MODEM
DTE
RXC
RXD
FIFO
Buffer
Rx
RXD
(4, 11)
Figure C-5 INT/RCV Mode Timing Block
C-4
INT/RCV Mode
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix D
DTE Interface Connectors
D.1 General
Table D-1 provides detailed information about each DTE interface
connector.
Table D-1 DTE Interface Signal Assignments
RS-232
V.35
34-pin
EIA-530
X.21
DB-15
Signal
DB-25
Stand-
alone
and
DB-25
Frame
DB-25
Standalone
and Frame
DB-25
Frame
Description
Function
Standalone
Standalone
Pin
Circuit/
Frame
Pin
Circuit Pin
Circuit
(Function)
Protective
Ground
1
1
A Frame 101
1
1
1
8
-
Chassis ground.
May be
isolated from
Signal Ground.
See Table 2-1.
[SHIELD]
Signal Ground
7
2
7
B Signal 102
Ground
7
2
AB
7
-
Common
[GND]
Signal and DC
power supply
ground.
Transmitted
Data
11
9
S
TD(B) 103
BA(A)
BA(B)
2
14
2
9
T(A)
T(B)
[TRANSMIT]
Serial digital
data from DTE.
The data
P
TD(A) 103 14
transitions must
occur on the
rising edge of
the transmit
clock.
Received
Data
3
12
13
R RD(A) 104
3
BB(A)
BB(B)
3
16
4
R(A)
Serial digital
data at the
output of the
modem
T
RD(B) 104 16
11 R(B)
[RECEIVE]
receiver. The
data transitions
occur on the
rising edge of
the receive
clock.
General
D-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix D. DTE Interface Connectors
ASMi-31 Installation and Operation Manual
Table D-1 DTE Interface Signal Assignments (Cont.)
RS-232
V.35
34-pin
EIA-530
X.21
DB-15
Signal
DB-25
Stand-
alone
and
DB-25
Frame
DB-25
Standalone
and Frame
DB-25
Frame
Description
Function
Standalone
Standalone
Pin Circuit/
(Function)
Frame
Pin Circuit
Pin Circuit
Request to
Send
4
4
C
RTS
105
4
CA(A)
4
19
3
10
C(A)
C(B)
[CONTROL]
A positive level
to ASMi-31
when data
19 CA(B)
transmission is
desired.
Clear to Send
5
5
D
CTS 106
5
CB(A)
A positive level
from ASMi-31
with delay,
13 CB(B)
after receipt of
Request to
Send, and
when ASMi-31
is ready to
transmit.
Data Set
Ready
6
6
E
DSR 107
6
CC(A)
A positive level
from ASMi-31
when the
22 CC(B)
power is on,
and ASMi-31 is
(a)not in the
DIGITAL
LOOP mode,
or (b) has not
received a
REMOTE
LOOPBACK
signal from the
remote unit.
Data Terminal 20
Ready
20
8
H
F
DTR 108 20 CD(A)
23 CD(B)
Not used.
Carrier Detect
8
DCD 109
8
CF(A)
8
10
5
12
I(A)
I(B)
A positive level
from ASMi-31,
10 CF(B)
[INDICATION] except when a
loss of the
received signal
is detected, or
when Data Set
Ready is
negative.
D-2
General
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Appendix D. DTE Interface Connectors
Table D-1 DTE Interface Signal Assignments (Cont.)
RS-232
V.35
EIA-530
X.21
Signal
Function
DB-25
Stand-
alone
and
DB-25
Frame
34-pin
Standalone
DB-25
Standalone
and Frame
DB-25
Frame
DB-15
Standalone
Description
Pin Circuit/
(Function)
Frame
Pin Circuit
Pin Circuit
External
Transmit
Clock
24
19
16
U SCTE(A) 113 24
W SCTE(B) 113 11
DA(A)
DA(B)
24
11
7
14
(A)*
(B)*
A serial data
rate clock input
from the data
source. Positive
clock
transitions must
correspond to
data transitions.
Transmit
Clock
15
14
10
Y SCT(A) 114
A SCT(B) 114
15
12
DB(A)
DB(B)
15
12
6
13
S(A)
S(B)
[SIGNAL
TIMING]
A transmit data
rate clock for
use by an
external data
source. Positive
clock
transitions
correspond to
data
transitions.
Receive Clock 17
22
23
X SCR(B) 115
V SCR(A) 115
17
9
DD(A)
DD(B)
A receive data
clock output
for use by
external data
sink. Positive
clock
transitions
correspond to
data
transitions.
Local Analog
Loop
18
18
L and j
141
18
LL
A control signal
input; when
on, commands
ASMi-31 into
Local Analog
Loopback
(V.54 Loop 3).
See Table 2-1.
* Unassigned pins according to X.21 standard.
Note
General
D-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix D. DTE Interface Connectors
ASMi-31 Installation and Operation Manual
Table D-1 DTE Interface Signal Assignments (Cont.)
RS-232
V.35
EIA-530
X.21
Signal
Function
DB-25
Stand-
alone
and
DB-25
Frame
34-pin
Standalone
DB-25
Standalone
and Frame
DB-25
Frame
DB-15
Standalone
Description
Pin Circuit/
(Function)
Frame
Pin Circuit
Pin Circuit
Remote
Loopback
21
21
N and h 140
21
RL
A control signal
input; when
on, commands
ASMi-31 to
send a remote
Loopback
command
(V.54 Loop 2)
to the remote
ASMi-31. See
Table 2-1.
Test Indicator 25
25
n and k
142
25
TM
A control signal
output from
ASMi-31;
positive during
any test mode.
D-4
General
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix E
Connecting RS-530 to
RS-422
Table E-1 Connecting RS-530 to RS-422
Signal Function
RS-449 (RS-422/423)
37-pin
Pin
RS-530
DB-25 Female
Standalone & Card
Cage Pin
Circuit
Circuit
Protective Ground
Signal Ground
1
Shield
SG
1
7
19
37
20
AB
DTE Common Return
DCE Common Return
Transmitted Data
SC
RC
4
SD (A)
SD (B)
2
BA (A)
BA (B)
22
14
Received Data
Request to Send
Clear to Send
Data Set Ready
Carrier Detect
6
RD (A)
RD(B)
3
BB (A)
BB (B)
24
16
7
RS (A)
RS (B)
4
CA (A)
CA (B)
25
19
9
CS (A)
CS (B)
5
CB (A)
CB (B)
27
13
11
29
DM (A)
DM (B)
6
CC (A)
CC (B)
22
13
31
RR (A)
RR (B)
8
CF (A)
CF (B)
10
External Transmit
Clock
17
35
TT (A)
TT (B)
24
11
DA (A)
DA (B)
E-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix E Connecting RS-530 to RS-422
ASMi-31 Installation and Operation Manual
Table E-1 Connecting RS-530 to RS-422 (Cont.)
Signal Function
RS-449 (RS-422/423)
37-pin
Pin
RS-530
DB-25 Female
Standalone & Card
Circuit
Cage
Pin
Circuit
Transmit Clock
(From DCE)
5
ST (A)
15
12
DB (A)
DB (B)
23
ST (B)
Receive Clock
(From DCE)
8
RT (A)
RT (B)
17
9
DD (A)
DD (B)
26
Local Analog Loopback 10
LL
18
21
25
LL
Remote Loopback
Test Indicator
14
18
RL
TM
RL
TM
E-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
Appendix F
Installation in 19" Rack
F.1 Installation of the ASMi-31 Unit in 19" Rack
The height of the unit is 1U (1.75"); the width of the unit is slightly less than
half the available mounting width. A rack adapter kit, RM-9, is available for
installing either a single unit or two units side by side in the 19" rack.
General
Disconnect the power before performing the procedures below.
Installation, operation, and maintenance of this unit should only be
performed by an experienced technician.
Warning
Rack adapter components for installing a single unit include one short
bracket and one long bracket.
Installation of a
Single Unit
➤ To install a single unit:
1. Fasten each bracket to the side walls of the unit by two screws
which are inserted into the two front holes on the side wall. (The
unit is supplied with nuts already in place on the inner side wall).
Note that the short bracket fastens to the left side of the unit, and
the long bracket to the right side of the unit (see Figure F-1).
Once the brackets are fastened to the side walls, the unit is ready
for installation in the 19" rack.
2. Place the unit in the rack and fasten the brackets to the side rails of
the rack using two screws on each side (not included in the kit).
Installation of the ASMi-31 Unit in 19" Rack
F-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Appendix F. Installation in 19" Rack
ASMi-31 Installation and Operation Manual
Figure F-1 Installation of a Single Unit
Rack adapter components for installing two units include two long side rails
(one for each unit) which slide one into the other, fastening the two units
together and two short side brackets which hold the two units in the 19"
rack (see Figure F-2).
Installation of Two
Units
F-2
Installation of the ASMi-31 Unit in 19" Rack
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
ASMi-31 Installation and Operation Manual
Appendix F. Installation in 19" Rack
Figure F-2 Installation of Two Units
➤ To install two units:
1. Fasten one long side rail to each unit (right side to one unit, left side to
the other unit) using the four screws supplied. The side rails must be
attached in opposing fashion, the narrow flange of the first rail opposite
the wide flange of the second rail.
2. Attach one short bracket opposite the side rail on each unit using the
four screws supplied.
3. Slide the side rail of one unit into the side rail of the other unit,
fastening the two units together (see Figure F-3).
4. Secure the supplied plastic caps to the ends of the rails, to prevent the
units moving and to protect the rail ends.
The assembled units can now be fastened to the side rails of the 19" rack by
means of four screws to each side(not included in the kit).
Installation of the ASMi-31 Unit in 19" Rack
F-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ph:727-398-5252/Fax:727-397-9610
Order from: Cutter Networks
Appendix F. Installation in 19" Rack
ASMi-31 Installation and Operation Manual
Figure F-3 Fastening Two Units Together
F-4
Installation of the ASMi-31 Unit in 19" Rack
Download from Www.Somanuals.com. All Manuals Search And Download.
Order from: Cutter Networks
Ph:727-398-5252/Fax:727-397-9610
|