QSD371614C4-250 User’s
Manual
Contact US:
Q-See Products
8015 E. Crystal Dr
Anaheim, CA 92807
Website:
Customer Service:
Phone:877-998-3440 X 538
Email:[email protected]
Tech Support:
Phone:877-998-3440 X 539
Email:[email protected]
Fax:
714-998-3509
Rev 042009
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. INTRODUCTION.................................................................................................................2
3.1 Front Panel............................................................................................................... 3
3.2 Rear Panel................................................................................................................ 3
3.3 Remote Control ....................................................................................................... 4
5.1 Hard Drive Installation............................................................................................ 6
5.2 Monitor Connection ................................................................................................ 6
5.3 Camera Connection................................................................................................ 7
5.4 Mouse Connection.................................................................................................. 7
5.5 DVR Power Connection.......................................................................................... 8
6.1 Camera ................................................................................................................... 10
6.2 Record.................................................................................................................... 11
6.3 Alarm ...................................................................................................................... 13
6.4 Screen .................................................................................................................... 15
6.5 System.................................................................................................................... 15
6.5.8 Firmware Upgrade........................................................................................ 20
6.6 Language ............................................................................................................... 20
6.7 Logout .................................................................................................................... 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
6.8 Exit.......................................................................................................................... 21
10.1 Installing File Player ........................................................................................... 23
10.2 Program Interface ............................................................................................... 24
10.3 Button Functions ................................................................................................ 24
11.2 Specifications...................................................................................................... 30
11.3 System Connection Diagram............................................................................. 31
11.4 DVR Accessories (included).............................................................................. 31
11.5 Q-SEE Product Warranty.................................................................................... 32
Customer Information Card...................................................................................................32
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
1. INTRODUCTION
The QSD371614C4-250 system provides a total 4-channel digital video security
surveillance system supporting duplex (simultaneous playback and record) functionality.
You can use front panel buttons, remote control unit or mouse to operate all DVR menu
settings.
The functionality of each access option is exactly the same.
2. DVR FEATURES
●
●
●
●
●
●
●
●
●
●
●
●
True Duplex Functionality: Simultaneous Play/Record.
PAL/NTSC Options.
High Quality Color Video at 50fps (PAL) or 60 fps (NTSC) Recording/Playback (shared by cameras).
Display Resolution: PAL 704*576; NTSC 704*480.
Recording Resolution: PAL 640*288; NTSC 640*240.
Recording Speed: PAL max. 50 fps (Quad); NTSC max. 60 fps (Quad) shared by cameras.
Recording Mode: Continuous, Motion Detection, Time Schedule.
Up to 8 days continuous recording at 30 fps setting with 250GB HDD.
USB port for file backup to USB Flash Drive Avg. 200KB/Sec.
Motion Detection and Video Loss Alarm Function.
OSD (On Screen Display): Supports multiple languages.
Power Recovery Auto-record Function.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
3. PHYSICAL UNIT
3.1 Front Panel
● IR Remote Receiver
● LED Light
(a) GREEN (PWR): The DVR unit is powered up and running.
(b) RED (HDD): System is in Recording Mode or in Playback Mode.
Some DVR is provided with touch-tone front panels. A series of buttons on the DVR front
panel operates the system’s basic functions, such as recording, playback, fast-forward,
3.2 Rear Panel
● VIDEO OUTPUT
Use this port to connect DVR to the monitor.
● VIDEO INPUT
Use these BNC ports to connect cameras to DVR system. You might need BNC adapter for
each (CH1-CH4) camera connection if the camera cables have RCA connectors.
● USB PORT
Use this port to attach USB cable to backup to PC hard drive or attach USB Flash Drive.
● AC-DC POWER ADAPTER JACK
Connect the power adapter into DVR and plug the power cable into the wall.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
[Input: AC 100-240V, 50/60Hz, 1.5A / Output: DC +12V == 3A]
● PS/2 MOUSE PORT
Use this port for PS/2 mouse connection. If you have USB port mouse, use USB - PS/2
adapter to connect with this port.
● Fan
3.3 Remote Control
The buttons on the DVR remote control unit operates the system’s basic functions, such as
recording, playback, fast-forward, reverse, etc. For more details about the DVR menu, refer
⑴ CH1↑
Use this button for full screen display for channel 1 on the monitor or move
the cursor up.
⑵ CH2↓
Use this button for full screen display for channel 2 on the monitor or move
the cursor down.
⑶ CH3←
Use this button for full screen display for channel 3 on the monitor or move
the cursor left.
Also user can press this button to reduce value when adjusting
parameters.
⑷ CH4→
Use this button for full screen display for channel 4 on the monitor or move the cursor to the
right.
Also user can press this button to increase value when adjusting parameters.
⑸ Quad
Use this button for full screen quad display on the monitor screen. If you push this button,
DVR will display all 4 channels (cameras) at the same time in quad screen.
⑹ ● (REC)
Press “REC” button to start manual recording. Then you will see this mar●k’ o‘ n the
selected channel of the screen, which means that the channel is now recording.
To stop manual recording, press “REC” again during recording mode.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
⑺ ■ (STOP)
To stop playback, press the “STOP” button.
⑻ ► (PLAY)
After recording, press “PLAY” button to start video playback.
Playback will start with the oldest unread video data and then continue playing.
⑼ ►► (FWD)
This is the fast forward button. To play the recorded video faster, press the “FWD” button.
There are three levels of fast forward playback speed.
(a) FF 1 (►►) : Play two times faster (2x) than the normal play.
(b) FF 2 (►►►): Play three times faster (3x) than the normal play.
(c) FF 3 (►►►►): Play four times faster (4x) than the normal play.
To change the fast forward play back speed level, press the “FWD” button again.
⑽ ◄◄ (REW)
This is the rewind button. To play the recorded video backward, press the “REW” button.
[NOTE]: The fast forward and reverse playback speeds will vary depending on the frame
rate and record quality settings, as well as the number of channels recorded.
⑾ ▍▍(PAUSE)
To pause the video playback, press the “PAUSE” button. Then the video display will be
stopped.
To continue playback, push the “PLAY” button.
⑿ Menu / ESC
It displays menu options or will go the previous screen.
⒀ UP / DOWN
To change a menu field, use the “UP” or “DOWN” buttons.
⒁ Select /Enter
Use this button to change values on main menu or sub menu setting. Also use can use this
button to increase value when adjusting parameters.
4. GETTING STARTED
Connect DVR to a TV or monitor.
Connect cameras (up to 4) to DVR.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
If you are using a Mouse it must be connected to DVR before you startup system.
Connect the power adapter to the DVR this will turn on the DVR.
Make sure that a hard drive and camera(s) are properly installed.
Start TV Monitoring and Recording.
After installation of hard drive, the hard drive must be fixed tight enough with screws.
If the power is turned off while recording (i.e. a power failure), the DVR will enter “Power
Recovery” mode at start up, detect that it has been shut down, and then re-initiate the
recording process.
5. HARDWARE SETUP
5.1 Hard Drive Installation
This model uses an internal SATA hard drive, and comes with a 250GB hard drive
pre-installed.
If you want to install a larger hard drive you would need to remove the cover of the DVR,
remove the power and data cables from the existing drive and unscrew it from the base,
then screw in the new hard drive and attach the power and data cables to it.
Connect the cables as follows:
5.2 Monitor Connection
To display video image from cameras on the monitor, the DVR’s video output signal needs
to be transferred to your TV set or monitor.
Connect a monitor to the
“VIDEO OUT” port on the DVR
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
Connect “VIDEO IN” of the monitor to “VIDEO OUT” of the DVR system using the BNC to
RCA cable that comes with the DVR.
5.3 Camera Connection
Connect the included video cables to the “VIDEO IN” of your DVR and “VIDEO OUT” of the
camera with video cable and plug in the camera’s power adapter to the power feed of the
video cable near the DVR.
“VIDEO OUT” on CAMERA
“VIDEO IN” on DVR
5.4 Mouse Connection
If you use a PS/2 mouse connect it to the port below on the system. A PS/2 Mouse must be
connected to DVR before startup system. You can also use a USB mouse with a PS/2
Adapter, or attached to the USB port.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
5.5 DVR Power Connection
Connect the DVR power adapter to the adapter jack at the rear panel of the DVR unit.
It will boot up the system.
If users install a new hard drive, it will ask you to format the hard drive before the system
starts to run (Below Fig). Choose format option by pressing the “PLAY” button.
Below is the information of input/output voltage for the power adapter:
Input: AC 100-240V, 50/60Hz, 1.5A
Output: DC +12V == 3A
6. SETUP
After installing a new hard drive on the
system, user needs to format the hard drive
first. The system opens to the login window,
there are three password levels in the
system, including admin (highest), operator, and guest (lowest). If the user does not
login to the system, he can only view live video display. And when the user logs into
the system, if he doesn’t operate the system within one minute the system will
logout automatically.
The system allows up to four user accounts. The administrator can set up the login name,
password and level for each user. The administrator can also add or delete users as he
wants to. (Please refer to Section 6.6.2 for Account Setup.)
The admin can operate everything. The operator can operate anything except examining
user accounts, formatting hard drives and modifying his password level. The guest can
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
operate live video display and image playback, or modify some parameter values that are
independent of recording. If user does not have the right to modify the parameter value,
there will be an identifier “
” on top right corner of the screen.
A: Mouse Control
After system boot-up, hold the right mouse button and the login window will open. Hold the
left mouse button to select the “Account”, and input correct account. Then left click the
“Password” option and input correct password. Then left click “Login” to enter system. There
is one factory-preset login “account/password” “admin/111111” at admin level. The user
can use it to login to the system for the first time.
After system boot-up, hold the right mouse button and there will be option menu on the
monitor (Fig (a)).
Fig (a)
Menu options in Fig (a):
Channel 1 view
Channel 3 view
Channel 2 view
Channel 4 view
All channel view
► Play record list
●
Manual recording or Stop manual recording
Menu option
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
Logout
Channel auto sequence. The iron “
” won’t display if the order of “auto sequence” is
“OFF”.
Move the mouse up or down to move the cursor. Click a left mouse button to change the
settings. Click a right mouse button to go back to the previous.
Hold the left mouse button to click the icon “
monitor (Fig (b)).
”. You will see the screen below on the
Fig (b)
B: The DVR Front Panel or Remote Control
After system boot-up, Press the “MENU” button on the DVR front panel or remote control
and there will be a login window. There is one factory-preset login “account/password”
“admin/111111” at admin level. The user can use it to login to the system for the first time.
After logging in to the system, press “MENU” button to make any changes to the DVR
settings and you will see screen on the Menu options on the monitor as Fig (b). Then press
the “UP” or “DOWN” key on the DVR front panel or remote control to move the cursor. Press
“SELECT” button on the front panel or remote control to change the settings. In the MAIN
MENU, the cursor “
” will be shown on the screen right next to each sub menu. To return
to the previous screen, press “MENU” button on the front panel or remote control.
6.1 Camera
Use this option to adjust the color for each channel (1,2,3,4). Go to DISPLAY for the option
to enable or disable each camera appearing on the screen display. Under the camera name
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
option you can change the name of each channel if you want to.
6.2 Record
Use this option to enable recording on the
channel (1,2,3,4). Only selected channels will be
recorded no matter how many camera channels
are displayed on the screen.
A: [RECORD FRAMERATE]
Set the recording frame rate for each channel.
The higher the recording frame rate, the more
natural movement you will see while playback.
You can set each channels frame rate
independently.
For PAL video output format, system default
value is 12 frames per second with each channel,
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
which means the system will record 48 frames per second with all channels. User can set
frame rate as 3~25 frames per second with each channel. The max value of total frames per
second with all channels is 50 frames.
For NTSC video output format, system default value is 15 frames per second with each
channel, which means the system will record 60 frames per second with all channels. User
can set frame rate as 3~30 frames per second with each channel. The max value of total
frames per second with all channels is 60 frames.
Press [SEL]/[CH4] button or hold the left mouse button to click icon “►” to increase the
recording frame rate for each channel. Press [CH3] button or use a left mouse button to click
“◄” icon to decrease the recording frame rate for each channel.
If you set the recording frame rate to off, the channel will not record.
B: [RECORD QUALITY]
Choose record quality setting among 1 / 2 / 3. The best record quality is 3, and the lowest
record quality is 1. The higher the record quality is, the higher the video image quality is
when you playback. Higher quality requires more hard drive space. Record frame rate,
record quality and available hard drive space will determine total recording time for the DVR
system.
C: [RECORD SCHEDULE]
Notice: To start motion record, make sure the period that you intend to record is labeled
“
” in the “record schedule” menu.
Press「Up」/「Down」button or move the mouse to move the prompt, then press「SEL」
or hold a left mouse button to adjust video record method during each time period. User can
also adjust the same record method during for entire time periods at the same time by
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
pressing the [QUAD] button on the DVR
front panel or remote control, or using
the left mouse button to click the time
period 24.
- Grey bar: No recording will be made for
this time period unless user activates
manual recording.
- Red bar: The time period with a red bar will continuously record (Time record) unless you
manually stop recording during that time.
- Green bar: The system will record whenever motion is detected. (See the following
chapter “MOTION DETECTION”)
6.3 Alarm
A: [BUZZER DURATION]
It sets the buzzer duration time (in seconds)
after an alarm is activated.
Value options are: “05, 10, 15, 20, 25, 30,
CONT, OFF” (in seconds). Default is “OFF”.
When “buzzer duration” is “cont”, the buzzer
will sound continuously.
B: [EVENT REC DURATION]
This option sets the length of time (in seconds) recording continues after a motion recording
event ends.
Value options are: “05, 10, 15, 20, 25, 30” (in seconds).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
C: [MOTION DETECTION]
[CHANNEL]
Select the channel or channels (1,2,3,4) that
you want to record when motion is detected.
[SENSITIVITY]
You can adjust the sensitivity of the built-in
motion sensor on the DVR system. The higher
the number, the higher the sensitivity is.
Values are “1, 2, 3, 4, Off”. The maximum sensitivity level is 4.
[MOTION AREA]
Use this option to select the size of the area that you want to be sensitive to motion.
Use the keypad button, remote control button or mouse to assign the area.
The keypad and mouse control instructions are below.
[Using keypad or remote control button]
Press [SEL] once to pick the area, press [SEL] twice to cancel the area.
CH1 - Up / CH2 - Down / CH3 - Left / CH4 - Right
[Using Mouse button]
While holding a left mouse button, move the mouse to select, deselect or reselect the motion
detection area for recording.
The area only can be selected from up to down and from left to right. When the block is
covered by blue shadow, it’s active to record. When the block is transparent, it will not be
recorded.
After completing the motion area setting, press “MENU” button or use the right mouse click
button to exit.
Before starting Motion Recording, user must complete the “Motion area” setup.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
6.4 Screen
[BORDER]
User can make the white borderline around each channel appear or disappear by setting
this option to “on” or “off”.
[AUTO SEQUENCE]
This option is used to setup the channels to
appear one at a time on the screen in
automatic sequence, and select the time that
each channel appears on the screen before
switching to the next channel.
Values are “Off, 1 to 10 seconds”. Default is “Off”.
[VIDEO ADJUSTMENT]
You can move the entire video screen up, down, left and right using this option.
Keypad usage on the front panel or remote control is below.
Use CH1 for up, CH2 for down, CH3 for left, CH4 for right.
Mouse function is below:
Use the right mouse click button, this will display the following icons on the screen:
“
”. Use a left mouse button to click each icon to select.
－“▲”for up, “▼” for down, “◄” for left, “►” for right, “
” for ESC.
6.5 System
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
In this menu, you can see the information of the hard drive installed in the DVR, change the
system password, adjust keypad tone, access browser event list or adjust current time on
the system.
If user logs into the system at admin level, the menu bar will be displayed as Fig (c). The
user can enter into the “account” option to examine all user accounts, and add or delete
users (Please refer to section “6.6.2” for account setup).
If user logs into the system at operator or guest level, the menu bar will be displayed as Fig
(d). The user can only modify his own password. (Please refer to section “6.6.3” for
password setup)
6.5.1 Hard Drive Setup
[OVERWRITE ENABLED]
If you choose Yes, recording continues and
overwrites previous recording when hard drive
is full.
If you choose No, the recording stops when the
hard drive is full. It won’t record until reformat
or replace the hard drive.
[FORMAT HDD]
If you format the hard drive, all the video data stored on the hard drive will be deleted. The
system has no restore option once the hard drive is formatted.
When you choose this option, it will ask for a password before formatting. The default
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
password is “111111”. Type the password and press any key button.
When HDD is formatting, and has successfully formatted, you will see the message below
blinking.
If the password is incorrect, you will see the below message blinking. Then try to enter the
right password again.
6.5.2 Account Setup
Only Administrator can log into the Account Setup
Menu, the Account Setup allows the administrator
to add new users, delete existing ones and modify
the user’s name/password/and level. The system
allows up to 4 user accounts.
[Account]/[Password]
In setup Menu display, move the cursor to change
the highlighted option to Account, and then press
[SEL] button to display Account/Password as
shown. All numbers, letters and signs in the pane
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
can be used as user account or password. Press
「SEL」to input value, and move the prompt to the
“Enter” option press 「SEL」to confirm.
Use CH1 for up, CH2 for down, CH3 for left, CH4
for right, Press “Shift” for change characters.
[Level]
Move the cursor to change the highlighted option to Level, and then press [SEL] to adjust
user level (operator/guest).
6.5.3 Password Setup
The default password is 111111. All numbers,
letters and signs in the pane can be used in
passwords. Press 「SEL」to input value, and move
the prompt to the option of “Enter”, press 「SEL」
to input current password.
Button function on the front panel or remote control:
Use CH1 for up, CH2 for down, CH3 for left, CH4 for right.
Use the same operation procedure to input new password and confirm password.
When password is changed successfully, user will see the below message:
When password change has failed, user will see the below message:
6.5.4 Clear Account Info
If you choose ON, the account information will be cleared when you logout of the system. If
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
you choose OFF, the account information will be kept when you logout of the system.
6.5.5 Keypad Tone
Set the keypad tone to “ON” or “OFF” to enable or disable keypad tone during operation.
6.5.6 Time Set
You can adjust the current time, date and year at any time by region. Set your region first
and set the current time so that the video back-up data can be played with the correct time
displayed.
Date and Time format are below.
*** 2008/08/08 － year/month/day
*** 01:01:00 － hour: minute: second
To move the cursor on the screen, use
“UP” and “DOWN” key on the DVR front
panel or remote control and then press “SELECT” button to change the numeric value. Once
you finish setting the time, press “MENU” button. Then press “DOWN” key and “SELECT”
button to apply the new time set. Or move the mouse to move the cursor up and down, use
the left mouse click button to change the numeric value. Once you finish time setting, use
the right mouse button to return. Then move the mouse to “Apply” and left click to apply the
new time set.
6.5.7 Event List
The Event list function enables playback
by event. On the Event list menu, it shows
all past recorded video, start time and end
time of each recorded video, showing
recording year/date/time in list. The HDD
can store 300 events in it at most. If the
events are over 300 items, user can play
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
previous event according to input time period if the data hasn’t been over-written.
To playback by Event list, using [UP]/[DOWN] or channel number (CH3 for Page Up or CH4
for Page Down) key on the front panel or remote control, select the event that you want to
playback and press “PLAY” button. Another way is to move the mouse up and down or click
the left mouse button (“◄” for Page Up or “►” for Page Down), select the event that you
want to playback and double click the left mouse button. Then it will playback the recorded
video data.
6.5.8 Firmware Upgrade
This menu is for upgrading the firmware of the DVR system through the USB port using a
USB flash drive; you can upgrade the system once you connect the USB flash drive that
contains a firmware file.
[CAUTION]: 1. Do not turn off the system while the system is upgrading. Otherwise, it will
cause the breakdown of the system that will require a special recovery
process.
2. If there is no hard drive installed in the DVR, the system can’t be upgrade.
3. In order to upgrade the system you must stop recording.
6.6 Language
Our system supports multiple language OSD (On Screen Display). It includes two types of
language systems (western and eastern). The language used is based on user’s
requirements.
On the “Language” menu, you can move the cursor to change it by pushing the “SELECT”
button on the front panel or remote control, and you can also use the mouse by single
left-clicking to select the language.
6.7 Logout
User can use this option to log out of the system.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
6.8 Exit
After you change settings on DVR menu, you need to confirm the changes under the EXIT
menu.
[EXIT & SAVE CHANGE]
Save change and go back to main screen.
[EXIT & DISCARD CHANGES]
No change and go back to main screen.
[LOAD SETUP DEFAULT]
Load default settings.
7. PLAYBACK WITH TIME SEARCH FUNCTION
This is an enhanced playback option,
which enables the user to manually
select a specific starting time for
playback.
[Keypad Control]:
In order to playback using time search
function, press the "PLAY” button on
front panel or remote control. Then press “SELECT” key to change the value of the
playback date and start time and press “PLAY” button again. The playback will start from the
date & time indicated by the user.
[Mouse Control]:
Use the right mouse button and left click the icon “►”, And then press the left mouse button
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
to change the value of the playback date and start time, then press the right mouse button.
Then use the left mouse button to click “Search”, the playback will start from the date & time
selected by the user.
8. BACKUP via USB Flash Drive
Our 4-channel DVR system has an enhanced back-up feature so that it’s possible to transfer
the video files recorded on the hard drive to USB flash drive.
Before you back up a stream of video data, have the USB flash drive formatted and ready
before attaching it to the DVR system.
In order to save the video data to these back-up devices, you should first start with playback.
Then press “MENU” button. Use “UP” key or “DOWN” key to move the prompt, then press
“SELECT” button to set the start time and the end time of the recorded video data that you
want to save to the flash drive. If you want to setup the end time faster, you can press the
button [►►FWD] to change the play speed that you want, and then press [DOWN] to select
end time again.
Move the prompt to “USB copy”, and press “SELECT” button or click the left mouse button
to back up a stream of video data to the USB flash drive.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
It will take a few minutes to copy the video data onto a USB flash drive. The file size number
is going up until it’s done while displaying the
messages below:
WRITING…
Then it will show the following message on the
screen:
FIXATING…
Take out the USB flash drive and attach it to your PC when it’s done.
Press “PLAY” button to continue on the system.
To view the video files saved on back-up devices on the computer, you need to use the
software provided with this package.
9. RECORDING LENGTH
Using Video System “NTSC”. Estimated record time basing on 250GB HDD:
The best record quality is 3, and the lowest record quality is 1.
DATA RATE
Record Time
Record Speed
REC Quality
(GB/Hour)
4.1
(Hour)
61
3
2
1
3
2
1
60F/Sec
3.2
78
2.3
108
125
156
208
2.0
30F/Sec
1.6
1.2
10. PLAYING BACKED UP VIDEO FILES ON PC
10.1 Installing File Player
Put the software installation CD in your CD-ROM.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
1) Click “ ” to play the video recorder in “*.VVF” format.
2) Still Capture
Click “ ” to capture single frame. Click the right mouse button to select “Options…” to
1. Open File
3. Rewind
2. Fast Reverse
4. Previous Frame
6. Next Frame
5. Pause
7. Play
8. Fast forward
9. Still Capture
11. Split 4
10. Split 1
12. Volume Scroll Bar
14. Playing Scroll Bar
16. Close the window
13. Mute On/Off
15. Minimize the window
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
setup path to save image. Click the left mouse button to select folder that you want to save
to, for example select the folder as “E:\VOC 4CH\backup”.
3) In “Options” window, you can setup other menu selections such as “General & On screen
display date/time format”.
√
□ Always on top (A): The client window will always display on top of all the windows.
√
□ Use DirectDraw: Show the run dialog to your graphic card.
√
□ Show playback time (T): The playback time will display on screen during play back.
On the menu selection “On screen display date/time format”, you can adjust the date/time
format displayed on screen.
4) Press the keyboard “F1” or click the right mouse button to select option “About Viewer F1”,
you can see the current version of the program.
5) Translate “VVF File Format (*.VVF)” into “AVI File Format (*.AVI)”.
As shown in the below illustrations, first click the right mouse button to select the option
“Export”, and then click the left mouse button which will display the window “Export To AVI”.
Next select the channels you want to export; Since this model does not have audio ports the
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
audio option is not available. Next click “
” to select input file and output file, and click
“
” to select video compression mode. Finally click “
” to start, and
progress will be showed as a percentage.
Notes: 1. When selecting video compression mode, user should test the compression
that he selects to see if it is matching his computer. If it doesn’t match the computer
may not be able to play the file.
2. Since this model does not have audio in ports the audio option is not available.
6) Capture
If you want to save a file in VVF file format (*.VVF) on your computer, you must make sure
the playback view is in pause state. Drag playing scroll bar to select start time, click the right
mouse button to select the option “Capture”, then left click “Mark In”. Drag playing scroll bar
ahead to select end time, click the right mouse button to select the option “Capture”, then left
click “Mark Out”. Last left click “Export” and there will be a window “Capture” on screen.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
The “Output Size” is the size of output file. Left click “
click “ ”.
” to setup save path. Then left
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
11. APPENDIX
11.1 QSD371614 4CH DVR series - compatible USB Flash Drives.
In case noise occurs on USB line due to a variety of reasons such as power noise, it might
cause an error during the data transferring process. In this case, it requires re-transferring
the date to the flash drive. If the device can process things normally in these exceptional
cases, things are okay. However, in some cases, it doesn’t operate normally.
For example, in case of a PC, it might not cause any problem under this kind of situation
because it is immune to these types of problems. However, in case of our products, they
often work better with some drives compared to others. These are the flash drives we
recommend based on our testing.
WORKING DEVICE LIST
MAKER
SONY
MODEL
MICROVAULT (SOK-USM1GJ)
SUM-LCB1
SIZE
1GB
1GB
2GB
2GB
4GB
1GB
2GB
1GB
1GB
SAMSUNG
TRANSCEND
APACER
SANDISK
FLEX
JF V30
Weblink (SYE5003358)
CRUZER micro
FD-02
KINGSTON
KINGSTON
LEMON
Data Traveler
Data Traveler
LEMON USB Drive
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
11.2 Specifications
ITEM
4CH DVR
Video Format
NTSC / PAL
Operation System
Video Input
Linux
4 channel Composite BNC
Video Output
1 channel Composite BNC
PAL: 100fps (4*25fps);
NTSC: 120fps (4*30fps);
Display Speed
PAL: Max. 50 frame per second;3fps~Max 25fps(each channel adjustable);
NTSC: Max. 60 frame per second;: 3fps~Max.30fps (each channel
adjustable)
Recording Speed
Compression Method
Enhanced M-JPEG
High@26kBytes.
Recording Mode
Recording Time
Hard Drive Capacity
USB port
Manual, Motion detection, Time Schedule
Up to 8 days continuous recording at 30fps with 250GB HDD
Up to 1.0 TB SATA interface HDD×1
File backup (Flash Drive) and software upgrade
PS/2 mouse and USB mouse with adapter
Yes
PS/2 Mouse
38KHZ IR Remote Control
Power Input
100-240VAC/DC 12V, 3A
Dimension (LxHxW)
10 x 8.5 x 4.75 in (250 x 218 x 42 mm)
ITEM
Cameras (QSC7614 – 6mm / QSC7614W – 3.6mm)
Image Sensor
¼ “ Color OV CMOS
400TVL
Horizontal Resolution
Minimum Luminance
Lens / Field of View
Power Supply
0 Lux (with LEDs)
6mm / 40° (QSC7614) & 3.6mm / 70° (QSC7614W)
DC12V
Power Consumption
Dimensions (WxDxH)
Weight
130mA (w/o LEDs), 300mA (LEDs on)
57x121x70mm (2.25x4.75x2.75in)
300g (10.4 oz)
Operating Temperature
Auto Gain Control
Auto Iris
-10°C to 50°C (14°F to 122°F)
On / Off
1/50 1/6000
S/N Ratio
>48dB
Night Vision
Up to 30ft
Effective Pixels
NTSC: 652x492
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
11.3 System Connection Diagram
Note: We STRONGLY recommend that you plug the DVR and cameras into a Transient Voltage
Surge Protector (UL-1449 rating). Look for a clamping voltage of 330 or lower, Joule rating of at
least 400, and a response time of 10 nanoseconds or less.
11.4 DVR Accessories (included)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
11.5 Q-SEE Product Warranty
Thank you for choosing our products.
All of our products users have a conditional free warranty repair service for hardware
within 12 months starting from purchase date, and a free exchange service within one
month (valid for manufacturing defects). Permanent upgrading service is provided for the
software.
Liability Exclusions:
Any product malfunction, abnormalities in operation or damage caused by following
reasons are not within the free service scope of our company. Please select payable
service.
(1) Equipment damage caused by improper operation
(2) Improper environment and conditions in/on which the equipment operates, e.g., improper
power, environment temperature, humidity and lightening strike etc. that cause equipment
damage.
(3) Damage caused by acts of nature: earthquake and fire etc.
(4) Equipment damage caused by the maintenance of personnel not authorized by our
company.
(5) Product sold over 12 months ago.
In order to provide various services to you, please complete registration procedure after
you purchase the product. Cut off or copy User’s Information Card and fax or mail it to us
website and clicking on the Register link.
Customer Information Card
User’s Name
Company Name
Postal Address
Postal code
Mr./Mrs.
Phone Number
E-mail
Model Number
of Product
Serial Number
of Product
Purchase Date
Distributor
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Manual-4CH Duplex DVR
If you have questions:
Contact Us:
Mailing Address:
DPS Inc.
Customer Service:
Phone: 877-998-3440 x 538
Email: [email protected]
8015 E. Crystal Dr
Anaheim, CA 92807
Website:
Tech Support:
Fax:
Phone: 877-998-3440 x 539
Email: [email protected]
714-998-3509
33
Download from Www.Somanuals.com. All Manuals Search And Download.
|