Q Logic Switch 59060 02 B User Guide

R
S i m p l i f y  
QLogic Fibre Channel Switch  
Event Message Guide  
Firmware Version 6  
59060-02 B  
Page i  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
59060-02 B  
Page iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
QLogic Fibre Channel Switch  
Event Message Guide  
S
Notes  
Page iv  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 1  
Introduction  
This manual describes the alarm messages for QLogic Fibre Channel switches  
using firmware version 6:  
This manual is organized as follows:  
Section 1 describes the intended audience, related materials, and technical  
support.  
Section 2 describes event logging concepts including definitions, how to  
configure the event log, how to display the event log, and how to download  
the event log from the switch.  
Section 3 describes the alarm message format and lists the alarm  
messages.  
1.1  
Intended Audience  
This manual is for Storage Area Network (SAN) administrators to provide a  
reference for switch alarm messages, their meanings, and follow up actions.  
1.2  
Related Materials  
The Fibre Channel Standards are available from:  
Global Engineering Documents, 15 Inverness Way East, Englewood, CO  
80112-5776 Phone: (800) 854-7179 or (303) 397-7956  
Fax: (303) 397-2740.  
59060-02 B  
1-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
1 – Introduction  
Technical Support  
S
1.3  
Technical Support  
Customers should contact their authorized maintenance provider for technical  
support of their QLogic switch products. QLogic-direct customers may contact  
QLogic Technical Support; others will be redirected to their authorized  
maintenance provider.  
Visit the QLogic support Web site listed in Contact Information for the latest  
firmware and software updates.  
1.3.1  
Availability  
QLogic Technical Support for products under warranty is available during local  
standard working hours excluding QLogic Observed Holidays.  
1.3.2  
Training  
QLogic offers certification training for the technical professional for both the  
SANblade™ HBAs and the QLogic switches. From the training link at  
www.qlogic.com, you may choose Electronic-Based Training or schedule an  
intensive "hands-on" Certification course.  
Technical Certification courses include installation, maintenance and  
troubleshooting QLogic SAN products. Upon demonstrating knowledge using live  
equipment, QLogic awards a certificate identifying the student as a Certified  
Professional. The training professionals at QLogic may be reached by email at  
1-2  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
1 – Introduction  
Technical Support  
A
1.3.3  
Contact Information  
Support Headquarters  
QLogic Corporation  
12984 Valley View Road  
Eden Prairie, MN 55344-3657  
USA  
QLogic Web Site  
Technical Support Web Site  
Technical Support Email  
Technical Training Email  
North American Region  
Email  
+1-952-932-4040  
+1 952-932-4018  
Phone  
Fax  
Europe, Middle East, and Africa Region  
Email  
Phone Numbers by Language  
+353 1 6924960 - English  
+353 1 6924961 - Français  
+353 1 6924962 - Deutsch  
+353 1 6924963 - Español  
+353 1 6924964 - Português  
+353 1 6924965 - Italiano  
Asia Pacific Region  
Email  
Phone Numbers by Language  
+63-2-885-6712 - English  
+63-2-885-6713 - (Mandarin)  
+63-2-885-6714 - (Japanese)  
+63-2-885-6715 - (Korean)  
Latin and South America Region  
Email  
Phone Numbers by Language  
+52 55 5278 7016 - English  
+52 55 5278 7017 - Español  
+52 55 5278 7015 - Português  
59060-02 B  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
1 – Introduction  
Technical Support  
S
Notes  
1-4  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section 2  
Events and Event Logging  
Messages originate from the switch or from the Enterprise Fabric Suite 2007  
application in response to events that occur in the fabric.  
2.1  
Understanding Severity Levels  
Events are classified by the following severity levels:  
Alarm – The alarm level describes events that are disruptive to the  
administration or operation of a fabric and require administrator intervention.  
Alarms are always logged and always displayed on the screen. Alarm  
thresholds can be defined for certain port errors to customize when to  
generate an alarm.  
Critical – The critical level describes events that are generally disruptive to  
the administration or operation of the fabric, but require no action.  
Warning – The warning level describes events that are generally not  
disruptive to the administration or operation of the fabric, but are more  
important than the informative level events.  
Informative – The informative level describes routine events associated with  
a normal fabric.  
2.2  
Displaying Events using the Event Browser  
Enterprise Fabric Suite 2007 provides an Event Browser, which displays events  
from the switch event log and events that are generated by Enterprise Fabric  
Suite 2007 itself. The Event Browser formats events by severity, timestamp,  
source, type, and description. Events read from the switch event log obtain the  
timestamp from the switch clock, while events generated by Enterprise Fabric  
Suite 2007 use the workstation clock.  
The Event Browser can maintain a maximum of 1500 events. Once the maximum  
is reached, the oldest events are discarded and replaced with new events. To  
display the Event Browser, open the Fabric menu and select Show Event  
Browser, or click the Events button on the tool bar. When you close Enterprise  
Fabric Suite 2007, all events in the Event Browser are lost. To save events to file  
before closing Enterprise Fabric Suite 2007, open the File menu from the Event  
Browser window and select Save As. For more information about the Event  
Browser, refer to the Switch Management User’s Guide for your switch.  
59060-02 B  
2-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
2 – Events and Event Logging  
Displaying the Events Using the Command Line Interface  
S
2.3  
Displaying the Events Using the Command Line Interface  
When you log into a switch through Telnet, the command line interface  
automatically displays the alarm history. You can use the Show Alarm or Show  
Log command to display the alarm history at any time. New alarm messages are  
displayed in the command stream as they occur. Refer to the Installation Guide for  
your switch for more information about the Show Log command.  
In the command line interface, each message has the following format:  
[ordinal][time_stamp][severity][source][message_ID][message_text]  
[ordinal]– A number assigned to each message in sequence since that last  
time the alarm history was cleared.  
[time_stamp]– The time the alarm was issued in the format  
day-month-hh:mm:ss:ms-yyyy. This time stamp comes from the switch for events  
that originate with the switch, and from the workstation for events that originate  
from Enterprise Fabric Suite 2007.  
[severity]– The event severity: A–Alarm, C–Critical, W–Warning,  
I–Informative.  
[source]– The program module or application that generated the event.  
Sources include Zoning, Switch, PortApp, EPort, Management Server. Alarms do  
not include the source.  
[message_ID]– A number that identifies the message using the following  
format: category.message_number  
[message_text]– The alarm message text  
Consider the following Informative level event example from the Switch source:  
[1][Wed May 26 12:30:29.965 UTC 2004][I][8400.0022][Switch][Successful login user  
(snmp@IB-session6) with admin privilege]  
2-2  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2 – Events and Event Logging  
Configuring the Event Log  
A
2.4  
Configuring the Event Log  
You can customize what events that are recorded in the switch event log using the  
Set Log command. With the Set Log command, you can filter the events to be  
recorded by component, specific ports, and severity level. You can choose from  
the following component events:  
E_Port events  
Management server events  
Name server events  
Port events  
Switch management events  
Simple Network Management Protocol (SNMP) events  
Zoning events  
Refer to the Command Line Interface Guide for your switch for more information  
about the Set Log command.  
2.5  
Archiving and Downloading the Event Log  
You can use the command line interface to create a file on the switch that contains  
the most recent 200 entries plus the previous 1000 entries. This file can then be  
downloaded to the workstation using FTP. To create and download a log file, do  
the following:  
1.  
2.  
Log into the switch through Telnet and create an archive of the event log.  
The Set Log Archive command creates a file on the switch named logfile.  
SANbox #> admin start  
SANbox (admin) #> set log archive  
Open an FTP session on the switch and login with the account name images  
and password images. Transfer the file logfile in binary mode with the Get  
command.  
>ftp ip_address  
user:images  
password: images  
ftp>bin  
ftp>get logfile  
xxxxx bytes sent in xx secs.  
ftp>quit  
59060-02 B  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2 – Events and Event Logging  
Configuring Port Alarm Thresholds  
S
2.6  
Configuring Port Alarm Thresholds  
You can configure the switch to generate alarms for selected events. Configuring  
an alarm involves choosing an event type, rising and falling triggers, a sample  
window, and finally enabling or disabling the alarm. You can configure port alarm  
thresholds for the following port events using the Enterprise Fabric Suite 2007 or  
the command line interface:  
CRC errors  
Decode errors  
ISL connections  
Device logins  
Device logouts  
Loss-of-signal errors  
To configure port threshold alarms using Enterprise Fabric Suite 2007, open the  
Switch menu in the faceplate display, and select Port Threshold Alarm  
Configuration. The Port Threshold Alarm Configuration dialog shown in  
prompts you to enable or disable all alarms, select an event, set triggers, set a  
sample window and enable or disable an individual alarm. Refer to the Switch  
Management User’s Guide for your switch for more information about port  
threshold alarms.  
To configure port threshold alarms using the command line interface, use the Set  
Config Threshold command. Refer to the Installation Guide for your switch for  
more information about the command line interface and the Set Config command.  
2-4  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section 3  
Event Messages  
This section lists event messages from the command line interface and Enterprise  
Fabric Suite 2007 in message ID sequence by the following severity levels:  
You can look up a message by its message ID or by searching for the message  
text. If the message you are looking for does not appear in this section, contact  
your authorized maintenance provider.  
3.1  
Alarm Events  
(A1000.000F) (The switch is canceling the hotreset - try again later)  
Meaning:  
You cannot move forward with the hot reset. All applications and  
switch resources are backing out of the procedure and returning to  
normal operation.  
Action:  
Ensure that the fabric is stable and that no changes are being  
made to switch configurations or connections and try again.  
(A1000.001D) (Hotreset failed and the switch must be reset normally)  
Meaning:  
The hot reset has failed and left the switch in an indeterminate  
state.  
Action:  
Reset the switch.  
(A1000.001E) (Hotreset failed and the switch is being reset)  
Meaning:  
There was a failure during the hotreset process, the switch is being  
reset normally.  
Action:  
None.  
59060-02 B  
3-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
3 – Event Messages  
Alarm Events  
S
(A1003.000B) (Failing release of fabric lock held by switch with domain domain_ID)  
Meaning:  
The local switch is locked as the result of zoning changes being  
made by a remote switch.  
Action:  
Wait for the lock to time out and try again.  
(A1003.000C) (Fabric Busy, failing lock request from domain domain_ID)  
Meaning:  
The command failed because the fabric is busy with another  
command in progress.  
Action:  
Retry the command in 10 seconds.  
(A1003.000D) (Fabric already locked by domain domain_ID)  
Meaning:  
Action:  
The switch given by the domain_ID has locked the fabric.  
Unlock the domain_ID lock on the switch given by domain_ID.  
(A1003.000E) (Couldn't acquire lock from domain domain_ID)  
Meaning:  
Action:  
Fabric may be changing, and therefor could not acquire the lock.  
Wait for the fabric to stabilize, then try again.  
(A1003.0010) (Segmenting, zoneset zone_set_name not defined)  
Meaning:  
In non-interop mode, there is a conflict in the zoning configuration,  
causing the Inter-Switch Link (ISL) to isolate. The zone set is not  
found within the local zoning data base while interop mode is  
disabled.  
Action:  
Contact your authorized maintenance provider.  
(A1003.0011) (Segmenting, zoneset zone_set_name already active)  
Meaning:  
In non-interop mode, there is a conflict in the zoning configuration,  
causing the Inter-Switch Link (ISL) to isolate. A switch tried to  
activate a zone set that is already active while interop mode is  
disabled.  
Action:  
Contact your authorized maintenance provider.  
(A1003.0012) (Segmenting, zoneset zone_set_name merge conflict)  
Meaning:  
In non-interop mode, there is a conflict in the zoning configuration,  
causing the Inter-Switch Link (ISL) to isolate. After a zone merge  
with interop mode disabled, two zone sets were discovered in the  
local zoning database with the same name, but different  
membership.  
Action:  
Contact your authorized maintenance provider.  
3-2  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1003.0013) (Segmenting, zone zone_name merge conflict)  
Meaning:  
In non-interop mode, there is a conflict in the zoning configuration,  
causing the Inter-Switch Link (ISL) to isolate. After a zone merge  
with interop mode disabled, two zone were discovered in the local  
zoning database with the same name, but different membership.  
Action:  
Contact your authorized maintenance provider.  
(A1003.0014) (Segmenting, alias alias_name merge conflict)  
Meaning:  
There is a conflict in the zoning configuration causing the  
Inter-Switch Link (ISL) to isolate. Two aliases were discovered in  
the local zoning database with the same name, but different  
membership.  
Action:  
Reconcile the active zone sets so that the two aliases have  
identical membership.  
(A1003.0015) (Zoneset Activation received from switch with domain domain_ID failed,  
unknown zoneset zone_set_name)  
Meaning:  
Action:  
A zone set activation received from the named switch failed  
because the zone set was not in the zoning database.  
Examine the named switch to verify that the zoning database is  
correct.  
(A1003.0016) (Releasing Lock held too long by domain_ID)  
Meaning:  
Action:  
Zone merge could not complete in the acceptable time.  
Check the status of the switch given by domain_ID.  
(A1003.0017) (Activation of zoneset by management server failed due to port port_number  
out of range.)  
Meaning:  
A zone member defined by domain ID and port was received within  
a management server AZSD command with a port number out of  
range.  
Action:  
Check management server application zoning configuration to  
assure zone members are properly configured.  
(A1003.001B) (Failing remote zoning configuration, total zoneset limit would be exceeded)  
Meaning:  
The maximum number of zone sets has been exceeded on the  
switch as a result of a zone merge.  
Action:  
Reduce the number of zone sets on the remote switch.  
(A1003.001C) (Failing remote zoning configuration, total member limit would be exceeded)  
Meaning:  
The maximum number of zone members has been exceeded on  
the switch due to a zone merge.  
Action:  
Reduce the number of zone members on the remote switch.  
59060-02 B  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1003.001D) (Failing remote zoning configuration, total zones in zonesets limit would be  
exceeded)  
Meaning:  
The maximum number of zones in zone sets has been exceeded  
on the switch as a result of a zone merge.  
Action:  
Reduce the number zones on the remote switch.  
(A1003.001F) (Failing remote zoning configuration, member limit for zone zone_name  
exceeded, (size= number_of_zones, limit= maximum_number_of_zones))  
Meaning:  
Action:  
The maximum number of members for the given zone has been  
exceeded as a result of a zone merge.  
Reduce the number of members in the given zone on the remote  
switch.  
(A1003.0020) (Failing remote zoning configuration, total zone limit would be exceeded)  
Meaning:  
The maximum number of zones has been exceeded on the switch  
as a result of a zone merge.  
Action:  
Reduce the number of zones on the remote switch.  
(A1003.0021) (Failing remote zoning configuration, Zoneset is empty)  
Meaning:  
An empty zone set was included as part of a zone merge and was  
rejected.  
Action:  
Modify the zoning database on the remote switch to remove or  
correct the empty zone set.  
(A1003.0022) (Unable to update database with newly activated information, a 'save'  
operation is in progress)  
Meaning:  
Modifications were being made to the security or zoning database  
while a security set or zone set was being activated or deactivated  
from a remote switch.  
Action:  
Avoid activating or deactivating a security set or a zone set while  
changes are being made anywhere in the fabric.  
(A1003.0023) (Fabric Busy Zoneset operation failed)  
Meaning:  
The activation or deactivation of a zone set failed because the  
fabric is currently busy.  
Action:  
Try the activation or deactivation again later.  
(A1003.0024) (Request already in progress (internal lock held))  
Meaning:  
Action:  
A fabric operation is currently in progress.  
Wait and try again.  
3-4  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1003.0025) (Error reading security set.)  
Meaning:  
There was a problem handling the activate direct management  
server command. The format of the command was not standard.  
Action:  
Check the security configuration.  
(A1003.0028) (SFC failure received from remote switch with domain domain_ID)  
Meaning:  
The remote switch given by domain_ID rejected the Staged Fabric  
Configuration (SFC) message, so the SFC request has failed.  
Action:  
Check the status of the remote switch at the given domain ID.  
There could be an issue with the security configuration or the  
zoning configuration.  
(A1003.0029) (No response received from switch with domain ID domain_ID)  
Meaning:  
The remote switch given by domain_ID did not reply to a Acquire  
Change Authorization (ACA) message, so the ACA request has  
failed.  
Action:  
Check the status of the remote switch at the given domain ID.  
There could be an issue with the security configuration or the  
zoning configuration.  
(A1003.002A) (No response received from switch with domain ID domain_ID)  
Meaning:  
A Staged Fabric Configuration (SFC) frame was sent to the switch  
given by domain_ID, but a response was not received.  
Action:  
Check the status of the remote switch at the given domain ID.  
There could be an issue with the security configuration or the  
zoning configuration.  
(A1003.002B) (No response received from switch with domain ID domain_ID)  
Meaning:  
A Update Fabric Configuration (UFC) frame was sent to the switch  
given by domain_ID, but a response was not received.  
Action:  
Check the status of the switch.  
(A1003.002C) (Zone Merge response indicates failure due to zoning limits, Isolating link)  
Meaning:  
Response from other switch indicates that the active zone sets  
could not be merged.  
Action:  
Edit or delete the conflicting zone objects or deactivate the zone  
set on the remote switch.  
59060-02 B  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1003.002D) (Zone Merge response indicates failure to merge, Isolating link)  
Meaning:  
The attempt to merge two fabrics failed because each active zone  
set contained a zone with the same name, but different  
membership.  
Action:  
Edit the affected zone to remove the conflict or deactivate one of  
the zone sets.  
(A1003.002F) (SW2 Zoning Not Supported by other switch, Isolating link)  
Meaning:  
The inter-switch link isolated because the local switch is configured  
for FC-SW-2 compliant zoning (interoperability mode set to  
Standard), but the remote switch is not.  
Action:  
Set the interoperability mode on the remote switch to Standard.  
(A1003.002E) (Zoning merge has been rejected.)  
Meaning:  
The attempt to merge two fabrics failed because each active zone  
set contained a zone with the same name, but different  
membership.  
Action:  
Edit the affected zone to remove the conflict or deactivate one of  
the zone sets.  
(A1003.0030) (Zone Merge rejected by remote switch.)  
Meaning:  
Action:  
The zone merge failed.  
See the switch log for more details on why the merge failed.  
(A1003.0031) (Error reading zoneset from activate direct.)  
Meaning:  
Action:  
A device supporting management server has sent an Activate  
Zoneset Direct $(AZSD) command that did not follow the expected  
standard layout.  
Contact your authorized maintenance provider.  
(A1003.0032) (Zoneset zone_set_name failed validity checks (empty or contains empty  
zone/alias))  
Meaning:  
Action:  
The zone set either has no zones or contains a zone or alias  
without members.  
Add zones and members, or remove the empty zones and aliases  
from the zone set.  
(A1003.0033) (No memory for command completion)  
Meaning:  
Action:  
Insufficient switch memory.  
Contact your authorized maintenance provider.  
3-6  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1003.0034) (Merge failed, total zoneset limit would be exceeded.)  
Meaning:  
A fabric merge failed because the combined number of zone sets  
exceeds the zoning database limit.  
Action:  
Remove zone sets from the local switch zoning database to allow  
fabric merge to complete.  
(A1003.0035) (Merge failed, invalid zone data received, ISOLATING)  
Meaning:  
Action:  
A remote switch sent a zone merge that was invalid.  
Reconcile interoperability modes on the local and remote switches  
so that they are the same.  
(A1003.0036) (Merge failed, member limit for zone zone_name exceeded, (size=  
member_number, limit= member_limit))  
Meaning:  
A fabric merge failed because the combined number of members  
in two zones having the same name exceeds the limit for the  
number of members in a zone.  
Action:  
Remove members from the zone on the local switch or the remote  
switch so that the combined sum is less than member limit.  
(A1003.0037) (Merge failed, Total zone member limit would be exceeded)  
Meaning:  
A fabric merge failed because the total number of zone members  
exceeds the zoning database limit.  
Action:  
Remove zone members from the local switch or the remote switch  
so that the combined sum is less than member limit.  
(A1003.0038) (Merge failed, Total zones in zonesets limit would be exceeded.)  
Meaning:  
A fabric merge failed because the total number of zones in zone  
sets exceeds the zoning database limit.  
Action:  
Remove zones from the local switch or the remote switch so that  
the combined sum is less than zones in zone sets limit.  
(A1003.0039) (Merge failed, total zone limit would be exceeded.)  
Meaning:  
A fabric merge failed because the total number of zones exceeds  
the zoning database limit.  
Action:  
Remove zones from the local switch or the remote switch so that  
the combined sum is less than maximum zone limit.  
(A1003.003A) (Zone Merge conflict for ZoneSet zone_set_name (Zone mismatch for zone=  
zone_name, check type or members), ISOLATING)  
Meaning:  
Action:  
A fabric merge failed because two zones of the same name in two  
zone sets of the same name have different membership.  
Reconcile the membership in the two zones so that they are the  
same.  
59060-02 B  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1003.003B) (Incomplete merge request sequence received, unable to process request.)  
Meaning:  
Action:  
A remote switch sent a merge request that was not understood.  
Check the remote switch for configuration errors or equipment  
malfunction.  
(A1003.003C) (Incompatible Zoning mode, Isolating link)  
Meaning:  
The fabric contains switches with a mix of interoperability mode  
settings.  
Action:  
Configure all switches in the fabric to have the same value for  
interoperability mode.  
(A1003.003E) (Security: Ports downed for INVALID_ATTACH require administrative action  
to be brought online.)  
Meaning:  
When deactivating a security set, ports that were previously  
downed due to security violations remain down.  
Action:  
Reset the ports or place the ports online.  
(A1003.003F) (ISL group empty and links up. Set ports offline to activate.)  
Meaning:  
Attempt at activating fabric binding with an ISL group that has no  
members is not allowed due because there are inter-switch links  
(ISL) logged in to the switch.  
Action:  
Configure all ISLs offline or add each ISL member with fabric  
binding information to the ISL group before activating.  
(A1003.0040) (Zone Member type member_type unsupported.)  
Meaning:  
An invalid zone member type was discovered in a zone. ACL hard  
zone membership must be defined by domain_ID and port number.  
Action:  
Correct the member type.  
(A1003.0041) (Zoning objects which contain Fibre Channel (FC) Address Members not  
being sent to remote switch on save, not supported in this mode)  
Meaning:  
An attempt was made to assign a zone member by FC address  
while Interop mode was disabled. When Interop mode is disabled,  
zone membership must be defined by world wide name or  
domain_ID and port number.  
Action:  
Enable Interop mode or change the zone membership type.  
3-8  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1003.0048) (Active Zone Set zone_name no longer in database, please deactivate zone  
set if not already in progress (the save will be deferred until zone set no  
longer active!)  
Meaning:  
The switch will not allow you to delete a zone set from the zoning  
database that has the same name as the active zone set.  
Action:  
Deactivate the active zone set before deleting the zone set from  
the zoning database that has the same name as the active zone  
set.  
(A1003.004C) (Active ZoneSet containing Fibre Channel Address may cause fabric to  
segment due to switches that do not support this zone member type)  
Meaning:  
Some switches in the fabric may not support Fibre Channel  
address zone members in the active zone set.  
Action:  
Edit the necessary zone sets to use WWN zone membership.  
(A1003.004D) (Port group does not contain entry for this switch)  
Meaning:  
The security set cannot be activated because the port group does  
not have an entry for the local switch world wide name.  
Action:  
Edit the port group to include the local switch world wide name.  
(A1003.004E) (Group entry for local switch does not support authentication)  
Meaning:  
The local switch world wide name group entry is not configured for  
authentication, but other members within the group are. This  
configuration is not allowed.  
Action:  
Change the local switch world wide name entry run CHAP  
authentication or remove CHAP authentication from other  
members of the group.  
(A1003.004F) (No Zone Merge Response)  
Meaning:  
A merge request was sent out to all switches in the fabric but a  
response was not received from at least one switch.  
Action:  
Check other switches in fabric to determine why a response was  
not sent.  
(A1003.0050) (ISL group does not contain entry for this switch)  
Meaning:  
The Inter-Switch Link (ISL) group does not contain an entry for the  
local switch world wide name. This a required entry.  
Action:  
Add the switch world wide name to the ISL group, then activate the  
security set.  
59060-02 B  
3-9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1003.0051) (Domain ID for local switch does not match fabric binding)  
Meaning:  
The configured fabric binding value for the local switch world wide  
name does not match the current domain ID for the switch.  
Action:  
Change the fabric binding value for local switch world wide name  
within the ISL group to the current value of the domain ID.  
(A1003.0052) (ISL group does not contain entry for switch domain_ID)  
Meaning:  
The ISL group does not contain an entry for each switch in the  
fabric. Fabric binding requires an entry for each switch.  
Action:  
Make sure there is an entry in the ISL group for each switch in the  
fabric and retry activating the security set.  
(A1003.0053) (Fabric binding must be unique, domains are assigned to multiple security  
group members  
Meaning:  
The configured fabric binding for the members of the ISL group are  
not unique.  
Action:  
Make the fabric binding settings unique for each member of the ISL  
group or set them to 0 so that they are not enforced.  
(A1003.0054) (Failure at remote switch)  
Meaning:  
A frame was sent to a remote switch, but the expected response  
was not received.  
Action:  
Check the status of the remote switch.  
(A1003.0055) (Problem on zoning save of following switches: domain_ID_list)  
Meaning:  
A zoning save was not able to be performed on some remote  
switches.  
Action:  
Examine the named switches for obvious problems, otherwise  
contact your authorized maintenance provider.  
(A1003.0058) (Active ZoneSet zone_set no longer in database, please deactivate zoneset if  
not already in progress or fabric will be inconsistent)  
Meaning:  
Zone set with the same name as the current active zone set no  
longer resides within the zoning database. The active zone set will  
not be added to the full zone set sequence or else the fabric will  
end up with an inconsistent zoning database.  
Action:  
Deactivate the active zone set to keep the fabric consistent.  
(A1003.0059) (Failing remote zoning configuration, zone member type not supported)  
Meaning:  
Remote switch's zoning configuration contains zone member type  
which is not supported.  
Action:  
Edit the zone to remove the unsupported member type.  
3-10  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1003.0060) (Zone Merge conflict (Alias mismatch for alias= alias, check members)  
Meaning:  
Action:  
The zone merge failed due to an alias mismatch.  
Examine the zoning configuration for conflicts.  
(A1003.0062) (Failing delete orphans zoning request, fabric locked by switch with domain  
ID domain_ID. Retry command later.)  
Meaning:  
Action:  
An attempt was made to delete the orphan zones while the fabric  
was locked.  
Retry the command later.  
(A1003.0063) (Failing delete orphans zoning request, fabric busy. Retry command later.)  
Meaning:  
An attempt was made to delete the orphan zones while the fabric  
was busy.  
Action:  
Retry the command later.  
(A1003.0064) (UFC failure received from domain domain_ID)  
Meaning:  
Update Fabric Configuration (UFC) message was received with a  
failed status from the switch given by domain_ID.  
Action:  
Check the status of the switch at the given domain ID.  
(A1004.0001) (Port in active hard zone, but not installed or present on this switch.)  
Meaning:  
A zone member in an ACL zone on this switch is defined with an  
invalid port number.  
Action:  
Examine the fabric and correct the zone membership.  
(A1004.0005) (No communication from neighbor switch on port port_number with domain  
ID domain_ID, lost route)  
Meaning:  
Action:  
This switch has not received a hello from the remote switch for 80  
seconds. Routes learned through this link are discarded.  
None.  
(A1004.0008) (Eport Isolating due to ELP Incompatibility)  
Meaning:  
An E_Port isolated due to an ELP (Exchange Link Parameter)  
incompatibility.  
Action:  
Review accompanying alarms for specific cause.  
(A1004.0009) (Eport Isolating due to ESC Incompatibility)  
Meaning:  
An E_Port isolated because the connecting switch failed to support  
the standard routing protocol FSPF.  
Action:  
Connect a compatible switch.  
59060-02 B  
3-11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1004.000A) (Eport Isolating due to EFP Domain Overlap)  
Meaning:  
An E_Port isolated because each fabric has a switch with the same  
domain ID.  
Action:  
Change the domain ID on one of the conflicting switches.  
(A1004.000B) (Eport Isolating due to Switch Administratively Offline)  
Meaning:  
An E_Port isolated because the local switch has been placed  
offline.  
Action:  
Configure the administrative state to Online to establish the link.  
(A1004.000C) (Eport Isolating due to Domain ID Locked, Domain ID unavailable)  
Meaning:  
An E_Port isolated because the requested domain ID matches  
another in the fabric and assigning an alternative is prohibited by  
the domain ID Lock parameter.  
Action:  
Disable the domain ID lock parameter or reconfigure the domain  
IDs.  
(A1004.000D) (Eport Isolating due to RDI SW Reject)  
Meaning:  
An E_Port isolated because the principal switch rejected the local  
switch domain ID.  
Action:  
Change the domain ID so that it is unique in the fabric.  
(A1004.000E) (Eport Isolating due to RDI Domain out of Range)  
Meaning:  
An E_Port isolated because the principal switch rejected the local  
switch domain ID as being out of range (1-239).  
Action:  
Change the domain ID to a valid number.  
(A1004.000F) (Eport Isolating due to Merge Zone Failure)  
Meaning:  
An ISL failed because the two active zone sets each have a zone  
with the same name, but different members.  
Action:  
Modify one or both of the zones so that their membership is the  
same, or deactivate one of the active zone sets. To connect the two  
fabrics, reset the affected E_Ports.  
(A1004.0010) (Eport Isolating due to Remote switch using same domain ID)  
Meaning:  
An E_Port isolated because the remote switch has the same  
domain ID.  
Action:  
Change the domain ID on one of the switches.  
3-12  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1004.0011) (Eport Isolating due to Remote switch isolated)  
Meaning:  
An E_Port isolated because the remote switch has the same  
domain ID.  
Action:  
Change the domain ID on one of the switches.  
(A1004.0012) (Eport Isolating due to ISL Security)  
Meaning:  
A remote switch attempted to log in but was rejected because it  
failed to satisfy the ISL group membership requirements.  
Action:  
Review the ISL group configuration and make the necessary  
corrections to include the remote switch as a member.  
(A1004.0013) (Eport Isolating due to all switches incapable of becoming Principal Switch)  
Meaning:  
An E_Port isolated because the principal priority on all switches is  
set to 254.  
Action:  
Configure one of the switches to be the principal switch by  
changing the principal priority.  
(A1004.0014) (Eport Isolating due to TOV mismatch indicated on ELP)  
Meaning:  
An E_Port isolated because the R_A_TOV or E_D_TOV time out  
values are different on the two switches.  
Action:  
Modify the switch configurations so that R_A_TOV or E_D_TOV  
values are the same.  
(A1004.0015) (Eport Isolating due to Invalid Attach)  
Meaning:  
Action:  
An E_Port isolated because of invalid attachment.  
Check for invalid attachment due to security or authentication  
incompatibility.  
(A1004.0020) (R_A_TOV mismatch indicated. Reconfigure to connect to remote switch.)  
Meaning:  
An E_Port isolated because the R_A_TOV timeout values on the  
two switches do not match.  
Action:  
Modify R_A_TOV so that it is the same on both switches. The  
recommended value is 10 seconds.  
(A1004.0021) (E_D_TOV mismatch indicated. Reconfigure to connect to remote switch.)  
Meaning:  
An E_Port isolated because the E_D_TOV timeout values on the  
two switches do not match.  
Action:  
Modify E_D_TOV so that it is the same on both switches. The  
recommended value is 2 seconds.  
59060-02 B  
3-13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1004.0023) (Attempting to connect to switch with incompatible time out value  
configured (R_A_TOV/E_D_TOV).)  
Meaning:  
An E_Port isolated because the values for R_A_TOV or E_D_TOV  
are not the same on both switches.  
Action:  
Modify the switches so that the time out values are the same.  
(A1004.0024) (Attempting to connect to switch that is in non-interop mode)  
Meaning:  
An attempt was made to connect to a switch with a different value  
for Interop Mode.  
Action:  
Modify the Interop Mode values so that they are the same on both  
switches.  
(A1004.0026) (Configured Domain ID domain_ID not available and Domain ID is locked on  
this switch)  
Meaning:  
Action:  
An attempt was made to connect a switch to a fabric with a  
conflicting domain ID and the domain ID could not be reassigned.  
Change the domain ID so that it is unique in the fabric or disable  
the domain ID lock so that the domain ID can be automatically  
reassigned.  
(A1004.0029) (No Switch capable of being Principal Switch. Reconfigure Principal Switch  
Priority.)  
Meaning:  
An E_Port isolated because the principal priority on all switches is  
set to 254.  
Action:  
Configure one of the switches to be the principal switch by  
changing the principal priority.  
(A1004.002B) (Port port_number not configured for E-Port capability, reconfigure to G/GL  
to connect to remote switch)  
Meaning:  
Action:  
An attempt was made by a remote switch to connect through a port  
that could not configure itself as an E_Port.  
Change the port type on the remote switch to G_Port or GL_Port.  
(A1004.002D) (Non-interop Legacy switch setting prevents domain/port zoning)  
Meaning:  
Action:  
Zone members involving switches of other vendors cannot be  
defined by domain ID and port number when Interop Mode is  
disabled and Legacy Address Formatting is enabled.  
Disable (False) the Legacy Address Formatting, enable Interop  
Mode, or reassign the zone members using a method other than  
domain ID and port number.  
3-14  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1004.002F) (Request for Domain ID rejected, WorldWide Name (WWN) device_WWN not  
allowed to join fabric.)  
Meaning:  
Action:  
The switch with the specified worldwide name is not allowed to join  
the fabric.  
Add the switch to a group in the active security set.  
(A1004.0030) (Topology change, lost route to switch with domain ID domain_ID)  
Meaning:  
Action:  
Connection was lost to a switch in the fabric.  
Inspect switch connections and device hardware for proper  
operation. Review accompanying alarms for other causes.  
(A1004.0032) (E_Port not supported on remote port. Reconfigure remote switch to  
connect.)  
Meaning:  
An E_Port isolated because the port on the remote switch could  
not configure itself as an E_Port.  
Action:  
Change the port type on the remote switch to G_Port or GL_Port.  
(A1004.0033) (Remote switch is in Interop mode or using Legacy Address Format)  
Meaning:  
A remote switch is attempting to connect with conflicting settings  
for Interop mode or legacy address format.  
Action:  
Configure the switches so that Interop mode and Legacy Address  
Format settings are the same throughout the fabric.  
(A1004.0034) (Failed to connect to a switch due to incompatibility - contact technical  
support.)  
Meaning:  
The two switches are incompatible. Possible causes include  
incompatible interoperability mode configurations, incompatible  
firmware versions, and incompatible licensing.  
Action:  
Check interoperability mode settings, firmware versions, and  
licensing on the remote switch. Otherwise, contact your authorized  
maintenance provider.  
(A1004.0035) (Failed to connect to a switch due to incompatibility - check interop  
settings.)  
Meaning:  
The remote switch failed to connect possibly because the  
interoperability mode setting is different than that of the local  
switch.  
Action:  
Reconcile the interoperability mode settings on the local and  
remote switch so that they are the same. Otherwise, contact your  
authorized maintenance provider.  
59060-02 B  
3-15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1004.0036) (Domain ID domain_ID assigned to different switches. Cannot join fabrics.)  
Meaning:  
An attempt was made to join two fabrics that possessed switches  
with the same domain_ID.  
Action:  
Change the domain_ID on one of the switches so that it is unique,  
and join the fabrics again.  
(A1004.0037) (Fabric Binding Error - please reconfigure: Local switch assigned domain  
domain_ID which is locked, fabric binding indicates domain domain_ID  
should be used.)  
Meaning:  
The local switch has a conflicting domain ID and the domain ID is  
locked.  
Action:  
Change the domain ID of the local switch.  
(A1004.0038) (WorldWide Name (WWN) device_WWN assigned domain domain_ID, fabric  
binding indicates this domain is reserved for device_WWN.)  
Meaning:  
Action:  
User activated fabric binding that conflicts with the current domain  
ID assignment.  
Change the domain ID of the device.  
(A1004.0039) (WorldWide Name (WWN) device_WWN currently in fabric, no fabric binding  
in active security set for this WWN.)  
Meaning:  
Action:  
Fabric binding failed due to security incompatibility.  
Check the security settings of the named device.  
(A1004.003F) (Request for Domain ID rejected, WorldWide Name (WWN) device_WWN not  
allowed to join fabric.)  
Meaning:  
Action:  
The switch with the specified WWN is not allowed to join the fabric.  
Add the switch to a group in the active security set.  
(A1004.0040) (World Wide Name (WWN) device_WWN assigned domain domain_ID, fabric  
binding indicates it should use domain_ID.)  
Meaning:  
Action:  
User activated fabric binding conflicts with the current domain ID  
assignment.  
Change the domain ID of the named device and then reconfigure  
the fabric.  
(A1004.0041) (Eport isolating due to E_Port License Exceeded.)  
Meaning:  
Action:  
An E_Port isolated because all licensed E_Ports are in use.  
Obtain a license key to license additional E_Ports.  
3-16  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1004.0043) (Forcing Domain ID change due to Interoperability setting from  
old_domain_ID to new_domain_ID.)  
Meaning:  
The Domain ID of the switch is changed due to an interoperability  
configuration change. The old Domain ID does not conform to the  
range of allowed Domain IDs for the new interoperability setting.  
Action:  
None.  
(A1004.0048) (Eport Isolating due to Port Binding failure)  
Meaning:  
A switch device attempted to login as an ISL, but that device was  
not configured in the port binding list.  
Action:  
Add the device to the port binding list.  
(A1004.0049) (Eport Isolating due to Remote inactive)  
Meaning:  
The remote switch is unresponsive and the link has not been  
brought up. The port will be isolated because the remote switch  
failed to respond.  
Action:  
Investigate the remote switch.  
(A1004.0050) (Maximum hard zoning member limit exceeded, Reverting to soft zoning.  
Requires port reset.)  
Meaning:  
The maximum number of zone members associated with a port is  
limited to 64. If this number is exceeded, the switch cannot enforce  
hard zoning and will revert to soft zoning.  
Action:  
Reduce the number of zone members associated with the port and  
reset the port.  
(A1004.0051) (Blade IO blade_number isolated due to startup problem)  
Meaning:  
There is an internal communication issue with an IO blade. It will  
be set down until it clears.  
Action:  
If this problem persists, contact your authorized maintenance  
provider.  
(A1004.0052) (Eport Isolating due to Switch Binding failure)  
Meaning:  
A device attempted to login as an ISL, but that device was not  
configured in the switch binding list.  
Action:  
Add the device to the switch binding list.  
(A1004.0053) (Adding Denial of Service entry for source FC Address 0xaddress)  
Meaning:  
A number of frames from the indicated address have been  
received. These frames are from a source that is not zoned with  
the destination. A denial of service entry will be set up to discard  
these frames.  
Action:  
Investigate the source at the specified FC address.  
59060-02 B  
3-17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1005.0006) (Request from WWN device_WWN address FC_address, failed authentication,  
verify MS security configuration)  
Meaning:  
Action:  
Management server authentication is enabled, and the received  
frame failed authentication.  
None  
(A1005.000A) (Cannot enforce zoning for member domain_ID, port_number, this zone  
member will be ignored)  
Meaning:  
Action:  
A zone member given by domain ID and port number could not be  
found in the fabric.  
Examine the fabric connections and zoning definitions.  
(A1005.000C) (Configuration error, insufficient credit in pool. Extended credit not granted  
for port port_number)  
Meaning:  
Action:  
Insufficient credits were available in the credit pool to grant the  
credit request.  
Decrease the number of requested credits or add more donor  
ports.  
(A1005.000D) (Configuration error, insufficient credit in pool. Extended credit not granted  
for port port_number)  
Meaning:  
Action:  
Insufficient credits were available in the credit pool to grant the  
credit request.  
Decrease the number of requested credits or add more donor  
ports.  
(A1005.000E) (Configuration error, can't extend credit on loop capable ports. Extended  
credit not granted for port: port_number)  
Meaning:  
Action:  
Loop ports cannot borrow credits from the credit pool.  
Change the port type to G_Port or F_Port.  
(A1005.0013) (Hotswap procedure failed - must hardreset switch)  
Meaning:  
The blade hot-swap procedure failed or the procedure was not  
followed correctly.  
Action:  
Perform a hard reset.  
(A1005.0020) (Warning - development logging is enabled)  
Meaning:  
Action:  
Development logging is enabled.  
Contact your authorized maintenance provider.  
3-18  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1005.0022) (Blade in slot slot_number must be reset after leaving Diagnostics  
AdminState)  
Meaning:  
After changing the switch administrative state from Diagnostics to  
any other state, the blade must be reset to complete the state  
change.  
Action:  
Reset the blade.  
(A1005.0024) (Switch must be reset after leaving the Diagnostics Admin State)  
Meaning:  
After changing the switch administrative state from Diagnostics to  
any other state, the switch must be reset to complete the state  
change.  
Action:  
Reset the switch.  
(A1005.0034) (System resource error - contact technical support)  
Meaning:  
Action:  
There is a system resources problem on the switch.  
Contact technical support.  
(A1005.0035) (System resource error - contact technical support)  
Meaning:  
Action:  
There is an internal problem on the switch.  
Contact technical support.  
(A1005.0036) (Hotswap procedure failed before last reset - must hardreset switch)  
Meaning:  
The blade hotswap procedure failed and the switch was reset  
without a power-on self test.  
Meaning:  
Reset the switch with a hard reset.  
(A1005.0037) (Hotswap procedure never completed - the blade will not be functional until  
the switch is hardreset)  
Meaning:  
Action:  
The blade hot-swap procedure was not completed.  
Reset the switch with a hard reset.  
(A1005.0038) (Switch incompatibility error - contact technical support)  
Meaning:  
Action:  
Switch incompatibility error.  
Contact technical support.  
(A1005.0039) (Fabric Login (FLOGI) from address FC_address failed)  
Meaning:  
Action:  
The payload of the FLOGI was not valid.  
Check device connection or replace the device. If the problem  
persists, contact your authorized maintenance provider.  
59060-02 B  
3-19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1005.003A) (Fabric Login (FLOGI) from address FC_address failed  
authorization/authentication)  
Meaning:  
Action:  
Security authentication failed.  
Check security configuration on both the device and the switch to  
ensure they are configured properly.  
(A1005.003B) (Warning - Debug logging filter level is set)  
Meaning:  
Action:  
Debug logging has been set using the Set Log Level command.  
Confirm that you intended to do this. If not, use the Set Log Level  
command to change the severity level to Info, Warn, or Critical.  
(A1005.003C) (User Port(s) port_numbers, isolated, lost steering path, administering them  
to state DOWNED.)  
Meaning:  
Action:  
The ports required for steering the user ports have failed.  
Contact your authorized maintenance provider.  
(A1005.003E) (Warning, port(s) port_numbers configured ONLINE, but remain DOWN after  
NDCLA.)  
Meaning:  
Ports that were down before a non-disruptive code load and  
activation remain down. This message serves as a reminder  
because the alarm log is cleared during the non-disruptive code  
load and activation.  
Action:  
None.  
(A1005.003F) (Badly formatted SML Notification Ack session session_ID string - string)  
Meaning:  
The switch sent a notification which was not formatted correctly,  
there may be a resource problem on the switch.  
Action:  
If this is a recurring message, contact your authorized maintenance  
provider.  
(A1005.0040) (Unsupported SFP within port.)  
Meaning:  
Action:  
An unsupported SFP transceiver was installed in the port.  
Replace the SFP.  
(A1005.0041) (Setting port admin state DOWN due to POST failure)  
Meaning:  
Action:  
The port failed the power-on self test and has been disabled.  
Contact your authorized maintenance provider.  
(A1005.0042) (Target device port_address attached to port port_number with  
IOStreamGuard Enabled)  
Meaning:  
Action:  
Target device attached to port with IO StreamGuard enabled.  
Disable I/O StreamGuard on the port.  
3-20  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1005.0045) (Configured port data conflicting within hardware capabilities)  
Meaning:  
Configured port settings conflict with the hardware capabilities of  
the port. The ports is downed.  
Action:  
Reconfigure the port to be compatible with the port hardware.  
(A1006.0004) (Zoning conflict, device_WWN is in an ACL hard zone, but device_WWN  
share a soft zone)  
Meaning:  
Action:  
The named zone members cannot communicate because they are  
members of different ACL hard zones.  
Place both zone members in the same ACL hard zone or exclude  
both from ACL hard zones.  
(A1006.0005) (Zoning enforcement error in Nameserver)  
Meaning:  
Action:  
An error occurred while checking ACL zoning.  
Contact your authorized maintenance provider.  
(A1006.0006) (Zoning conflict, device_WWN and device_WWN do not share an ACL hard  
zone, but device_WWN share a soft zone)  
Meaning:  
Action:  
The named zone members cannot communicate because they are  
members of different ACL hard zones.  
Place both zone members in the same ACL hard zone or exclude  
both from ACL hard zones.  
(A1007.0001) (NS: Unspecified zoning enforcement error)  
Meaning:  
A device was not authorized or it failed security checks and will not  
be allowed to join the fabric.  
Action:  
None.  
(A1007.0002) (Security: WWN device_WWN not authorized to join))  
Meaning:  
The device WWN is either not configured in the security data base,  
or it is not configured for Challenge Handshake Authentication  
Protocol (CHAP).  
Action:  
Add the device WWN to the active security set if it missing, or  
modify the group to allow for CHAP authentication with the other  
devices.  
(A1007.0005) (Security: Authentication request was rejected by port.)  
Meaning:  
Indicates that a remove switch rejected a security authentication  
attempt. The port will isolate.  
Action:  
Checks the security configuration on the remote switch to  
determine the problem.  
59060-02 B  
3-21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1007.0006) (Security: Could not validate Authentication Response from port_number,  
payload seems to be incorrect.)  
Meaning:  
Action:  
The format of the payload of the response frame does not match  
what was expected.  
Check for errors on the remote side of the link. Check the  
transceiver and cable. Update firmware on remote switch.  
(A1007.0007) (Security: Fabric Binding (ESA) not supported on remote switch and Fabric  
Binding is enabled, failing security checks)  
Meaning:  
Either fabric binding is not enabled on the remote switch or the  
remote switch does not support security at all.  
Action:  
Check the security configuration on the remote switch.  
(A1007.0008) (Security: ESA Response failure, failing security checks)  
Meaning:  
A failure was received during processing of the ESA received  
frame. Either the payload did not match the standard layout or the  
payload status indicated a reject.  
Action:  
Check for errors on the remote side of the link. Check the  
transceiver and cable. Update firmware on remote switch.  
(A1007.0009) (Security checks EFMD response failure, failing security check.)  
Meaning:  
Action:  
A remote switch rejected a EFMD frame. The port will be isolated.  
Check remote switch for the reason that the EFMD frame was  
rejected. It is possible that the FabricBindingEnabled parameter is  
different on the two switches.  
(A1007.000A) (Security: Dropping lock held by domain domain_id for number seconds)  
Meaning:  
A remote switch has held the fabric lock for too long. Local switch  
is dropping the lock in order to send out a Exchange Fabric  
Membership Data (EFMD) frame.  
Action:  
None.  
(A1007.000B) (Security: EFMD Rejected, bad revision)  
Meaning:  
The remote switch is running at a different Exchange Fabric  
Membership Data (EFMD) version level than the local switch. Ports  
will isolate.  
Action:  
None  
3-22  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1007.000C) (Security policy restrict mode, security db differs)  
Meaning:  
The current security policy calls for restrict mode which means that  
all switches in the fabric must have the same security databases or  
the ISLs will not login. In this case, the security databases differ.  
Action:  
Reconfigure the active security set so that the ISL group members  
are the same.  
(A1007.000D) (Security policy in mode mode, other switch in mode mode, sec db conflict)  
Meaning:  
The security policy on the local switch differs from that of the  
remote switch.  
Action:  
Configure the security policy on the remote switch to match that of  
the local switch.  
(A1007.000E) (Security: Auth challenge received from WWN port_WWN, not Authorized to  
join)  
Meaning:  
A challenge authentication frame was received from a remote  
switch, but the local switch does not have an entry for itself within  
the active security set ISL group.  
Action:  
Edit the ISL group to include the local switch.  
(A1007.000F) (Security: Chap session Gen Response indicates error, chap unable to  
authenticate)  
Meaning:  
An Authentication Response frame cannot be built because the  
CHAP session is not in the right state. The port will isolate.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
(A1007.0010) (Security: Chap session Receive Challenge indicates bad state, chap unable  
to authenticate)  
Meaning:  
The CHAP session state is not in the correct state for a Challenge  
message. Port will isolate.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
(A1007.0011) (Chap failure, isolating with Invalid Attach)  
Meaning:  
Frame does not match format for a CHAP status frame. Ports will  
isolate.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
59060-02 B  
3-23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1007.0012) (Port with World Wide Name (WWN) port_WWN address FC_address not  
authorized to login, verify MS security configuration)  
Meaning:  
Action:  
The port cannot login with the current security configuration.  
Add the named port to the Management Server group in the active  
security set.  
(A1007.0013) (Response from address FC_address, lacks authentication, discarding)  
Meaning:  
A response received on the indicated port lacked Common  
Transport (CT) authentication.  
Action:  
Verify that the CT security configuration of the management  
application using the remote port is compatible with the  
configuration of the Management Server security group on the  
switch.  
(A1007.0014) (Response from WorldWide Name (WWN) device_WWN address FC_address,  
failed authentication, discarding)  
Meaning:  
Action:  
A request received on the indicated port failed Common Transport  
(CT) authentication.  
Verify that the CT security configuration of the management  
application using the remote port is compatible with the  
configuration of the Management Server security group on the  
switch.  
(A1007.001C) (Security: Bad Authentication Flags)  
Meaning:  
The received AUTH frame did not meet the standard format for the  
frame payload. Within the header portion of the payload, there are  
some flags that are supposed to be set to zero. This frame has the  
flags set to something other than zero.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
(A1007.001D) (Ignoring RADIUS Server Radius_Server, invalid IP address configured)  
Meaning:  
Action:  
A Radius Server could not be found at the configured IP address.  
Check the Radius Server, or change the configuration to use an IP  
address for a valid Radius Server.  
(A1007.001F) (Access reject from RADIUS server IP_address:port for device on this port)  
Meaning:  
Security authentication retries has reached maximum retry count.  
The port will now isolate.  
Action:  
Check the security configuration.  
3-24  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1007.0020) (MAX Retry count reached on CHAP Authentication Protocol Reset, failing  
Authentication)  
Meaning:  
Action:  
A RADIUS server has rejected a RADIUS authentication request.  
Check the configuration on both the switch and on the RADIUS  
Server for incompatibilities.  
(A1007.0021) (No response to RADIUS access request for device on port port)  
Meaning:  
A configured RADIUS server did not respond to an authentication  
request within the timeout period.  
Action:  
Check RADIUS server configuration and the RADIUS server.  
(A1007.0022) (Invalid response authenticator from RADIUS server IP_address:port, check  
shared secret)  
Meaning:  
Action:  
RADIUS server configuration issue.  
Check the shared secret. The shared secret must be configured on  
both the RADIUS server and the switch.  
(A1007.0023) (Invalid response authenticator from RADIUS server IP_address:port, check  
shared secret  
Meaning:  
Action:  
There is a RADIUS configuration problem.  
Confirm that the shared secret configured on the switch is identical  
to the shared secret configured on the RADIUS server.  
(A1007.0024) (Invalid access accept from RADIUS server IP_address:port, bad or missing  
Service-Type)  
Meaning:  
Action:  
A service-type RADIUS attribute was not found within a RADIUS  
packet.  
This is a RADIUS Server configuration issue. Consult your  
RADIUS server documentation.  
(A1007.0025) (Security feature not supported.)  
Meaning:  
The switch is coming out of Non-Disruptive Code Load and  
Activation (NDCLA) and had an active security prior to the NDCLA,  
but the security feature is no longer supported.  
Action:  
A license key may be required for the security feature.  
(A1007.0026) (Unable to validate Chap Response from device_WWN, possible Chap secret  
misconfiguration or security breach attempt.)  
Meaning:  
Action:  
A CHAP authentication attempt failed due to failure while  
comparing secrets.  
Check security configuration.  
59060-02 B  
3-25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1007.0027) (Radius server could not validate authentication response from port_number)  
Meaning:  
Action:  
RADIUS authentication failed.  
Confirm that the secret is the same on the switch as it is on the  
RADIUS server.  
(A1007.0028) (Security: 2-Way Authentication, No security entry found for port)  
Meaning:  
Unable to locate a security member entry to complete a two way  
authentication.  
Action:  
Edit the group to include the port.  
(A1007.0029) (Security protocol not using chap, unable to authenticate.)  
Meaning:  
A CHAP negotiate frame was received that specifies an  
unsupported authentication protocol.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
(A1007.002A) (Inconsistent Fabric Binding configuration. Enabled on remote switch(s),  
disabled on local switch.  
Meaning:  
Inconsistent fabric binding configuration settings between local and  
remote switch. All switches in fabric must have the same  
configured fabric binding setting.  
Action:  
Enable or disable fabric binding on all switches.  
(A1007.002B) (Security: Chap session Negotiate Authentication failed)  
Meaning:  
Local switch received an authentication negotiate frame which  
failed processing. Either the payload of the frame did not match the  
standard layout of the frame or the CHAP session between the  
devices being authenticated was not in the state where the  
negotiate frame was expected.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
(A1007.002C) (Security: Authentication protocol msg (AUTH_DONE) inconsistent with  
Authentication protocol in progress)  
Meaning:  
The local switch received a AUTH_DONE command authentication  
frame while the chap session was not in the correct state to expect  
this type of frame. Remote device is not following standard  
authentication protocol.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
3-26  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A1007.002D) (Ignoring RADIUS Server RADIUS_server, invalid UDP port configured)  
Meaning:  
A RADIUS server was configured with invalid data for the UDP  
port. This is a required configuration field for the RADIUS server to  
be used.  
Action:  
Set the UDP port value in the switch RADIUS server configuration  
using the Set Setup Radius command.  
(A1007.002E) (Ignoring RADIUS Server RADIUS_server, zero timeout configured)  
Meaning:  
A RADIUS server was configured with invalid data for the timeout  
value. This is a required configuration field for the RADIUS server  
to be used.  
Action:  
Set the timeout value in the switch RADIUS server configuration.  
using the Set Setup Radius command.  
(A1007.002F) (Ignoring RADIUS Server RADIUS_server, no shared secret is configured)  
Meaning:  
A RADIUS server was configured with invalid data for the shared  
secret. This is a required configuration field for the RADIUS server  
to be used.  
Action:  
Set the shared secret in the switch RADIUS server configuration.  
using the Set Setup Radius command.  
(A1007.0030) (Security protocol not using chap, unable to authenticate.)  
Meaning:  
A CHAP Negotiate frame was received that specifies an  
unsupported Dilfie Helmann (DH) Group type.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
(A1007.0031) (Security protocol not using chap, unable to authenticate.)  
Meaning:  
A CHAP Negotiate frame was received that specified an  
unsupported hashing algorithm or an algorithm that is not allowed  
for this security member's configuration.  
Action:  
Check the remote device for a possible error condition. Reset the  
port to retry again. If errors continue, disable CHAP for this device  
if it belongs in the fabric.  
59060-02 B  
3-27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A1007.0032) (Fabric conditions or configurations do not currently allow for changing  
fabric binding.)  
Meaning:  
An attempt to change the fabric binding setting was rejected due to  
current fabric binding configuration settings within the active  
security set.  
Action:  
Check fabric binding settings and the domain IDs of the switches  
within the fabric. Add missing switches to the ISL group of the  
active security set.  
(A1007.0033) (Device device_WWN failed port binding.)  
Meaning:  
A device attempted FLOGI, but that device was not configured in  
the port binding list for the specified port.  
Action:  
Add the device to the port binding list.  
(A1007.0034) (Device device_wwn failed switch binding.)  
Meaning:  
A device attempted FLOGI, but that device was not configured in  
the switch binding list for the specified switch.  
Action:  
Add the device to the switch binding list.  
(A1007.0035) (Port taken offline due to switch binding failure following configuration  
change.)  
Meaning:  
A configuration change was made to the switch binding list such  
that the device(s) on the port were no longer allowed to be logged  
in.  
Action:  
Add the devices to the switch binding list.  
(A1007.0036) (Port taken offline due to port binding failure following configuration  
change.)  
Meaning:  
A configuration change was made to the port binding list such that  
the device(s) on the port were no longer allowed to be logged in.  
Action:  
Add the devices to the port binding list.  
(A1007.0037) (Device device_wwn failed port binding)  
Meaning:  
A switch device attempted to login as ISL but that device was not  
configured in the Port Binding list for the specified port.  
Action:  
Add the device to the port binding list.  
(A1007.0038) (Device device_wwn failed switch binding)  
Meaning:  
A switch device attempted to login as ISL but that device was not  
configured in the Switch Binding list.  
Action:  
Add the device to the switch binding list.  
3-28  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A2000.0001) (Pwr1 removed - ALARM SET)  
Meaning:  
Action:  
Power supply #1 was has failed or was removed from the switch.  
Contact your authorized maintenance provider.  
(A2000.0002) (Pwr2 failure - ALARM SET)  
Meaning:  
Action:  
Power supply #2 was has failed or was removed from the switch.  
Contact your authorized maintenance provider.  
(A2001.0001) (Pwr2 was installed - ALARM CLEARED)  
Meaning:  
Action:  
Power supply #2 was installed.  
None.  
(A2001.0002) (Pwr1 OK - ALARM CLEARED)  
Meaning:  
Action:  
Power supply OK.  
None.  
(A2002.0001) (fan_number was removed)  
Meaning:  
Action:  
A field replaceable fan was removed from the switch.  
Reinstall the fan.  
(A2002.0002) (Fan fan_number failure - ALARM SET)  
Meaning:  
Action:  
A cooling fan has failed.  
Replace the fan if it is a field replaceable unit. Otherwise, contact  
your authorized maintenance provider.  
(A2002.0003) (Fan flow mismatch - ALARM SET)  
Meaning:  
Action:  
The switch has two cooling fans with opposite air flow directions.  
Replace one of the fans with another fan with the correct air flow  
direction.  
(A2003.0003) (Fan flow match - ALARM CLEARED)  
Meaning:  
Action:  
The opposing fan air flow condition has been corrected.  
None.  
(A3000.0001) (Temp overheat, sensor_name sensor reads value C - ALARM SET)  
Meaning:  
Action:  
The chassis temperature has reached a failure threshold.  
Check air flow, fan operation, and ambient temperature. If the  
problem cannot be corrected, power down the switch.  
59060-02 B  
3-29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A3000.0002) (Temp sensor sensor_name on blade slot_number reads value C - ALARM  
SET)  
Meaning:  
Action:  
The chassis temperature has reached a failure threshold.  
Check air flow, fan operation, and ambient temperature. If the  
problem cannot be corrected, power down the switch.  
(A3001.0001) (Temp overwarm, sensor_name sensor reads value C - ALARM SET)  
Meaning:  
Action:  
The chassis temperature has reached a warning threshold.  
Check air flow, fan operation, and ambient temperature.  
(A3002.0001) (sensor name sensor has returned to normal range - ALARM CLEARED)  
Meaning:  
The chassis temperature has returned to the normal range and the  
alarm condition has been cleared.  
Action:  
None  
(A3002.0002) (Temp sensor sensor_name on blade slot_number reads value C - ALARM  
CLEARED)  
Meaning:  
Action:  
The named blade has returned to the normal operating  
temperature range.  
None.  
(A3003.0001) (Fatal hardware error detected. The switch is not operational. Use 'show  
post log' for more info)  
Meaning:  
A fatal hardware error was discovered during the  
Power-On-Self-Test (POST) phase of startup. This switch is not  
currently operational.  
Action:  
Enter the Show Post Log command to investigate.  
(A3003.0002) (POST detected a fatal error the last time it ran. The switch is not  
operational. Use 'show post log' for more info)  
Meaning:  
A fatal hardware error was discovered from the previous  
Power-On-Self-Test (POST). This switch is not currently  
operational.  
Action:  
Enter the Show Post Log command to investigate.  
(A3003.0003) (Diagnostics have detected a fatal error on the I/O blade in slot slot_number.  
The blade is not operational.)  
Meaning:  
Diagnostic testing has determined that there is a failure on  
specified I/O blade. The blade did not pass the Power-On-Self-Test  
(POST).  
Action:  
Enter the Show Post Log command to investigate.  
3-30  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
A
(A3004.0001) (Non-fatal hardware error detected. Use 'show post log' for more info)  
Meaning:  
A non-fatal hardware error was discovered during the  
Power-On-Self-Test (POST) phase of startup.  
Action:  
Enter the Show Post Log command to investigate.  
(A3004.0002) (Diagnostics have detected a partial failure on the I/O blade in slot  
slot_number)  
Meaning:  
Diagnostic testing has determined that there is a partial failure on  
specified I/O blade. Most likely, at least one of the ports did not  
pass the Power-On-Self-Test (POST).  
Action:  
Enter the Show Post Log command to investigate.  
(A3008.0000) (The configuration area was damaged or a Remake Filesystem was  
performed from PROM mode. You must perform a 'config restore' to clear  
this error.)  
Meaning:  
The configuration area was damaged or a Remake Filesystem was  
performed from Maintenance mode.  
Action:  
Enter the Config Restore command to clear the error. If this does  
not correct the problem, contact your authorized maintenance  
provider.  
(A3014.0001) (Blade in slot slot_number set Down due to failure of all AuxPorts)  
Meaning:  
The blade in the named slot has isolated because all auxiliary ports  
to the cross-connect blades have failed.  
Action:  
Contact your authorized maintenance provider.  
(A3014.0002) (Blade in slot slot_number set Online due to internal failure recovery)  
Meaning:  
The blade in the named slot has recovered at least one auxiliary  
port to a cross-connect blade and is no longer isolated.  
Action:  
None  
(A3014.0003) (Blade blade_ID set Down due to blade type mismatch)  
Meaning:  
The I/O blade given by blade_ID has isolated because the  
operational blade type does not match the configured blade type.  
Action:  
Change the configured blade type to match the I/O blade that is  
present, or insert an I/O blade of the configured blade type.  
(A4000.0001) (threshold of value hit rising trigger trigger_number in value second window on  
port port_number - ALARM SET  
Meaning:  
Action:  
The switch exceeded the specified threshold rising trigger in the  
specified sample window.  
Investigate the specified port for problems or adjust the rising  
trigger or sample window.  
59060-02 B  
3-31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Alarm Events  
S
(A6000.0002) (Configured port speed for port port_number not compatible with media.)  
Meaning:  
The transceiver in the named port is not capable of transmitting at  
the configured port speed.  
Action:  
Reconfigure the port speed or replace the transceiver.  
(A6001.0001) (cmon: insufficient memory)  
Meaning:  
The Hotreset command has failed due to insufficient memory on  
the switch. The switch has been returned to its state before the  
Hotreset command was entered.  
Action:  
If acceptable, enter the Reset Switch command to reboot the  
switch. Contact technical support if a non-disruptive code load and  
activation is required.  
(A6001.0002) (cmon: blade failed NDCLA)  
Meaning:  
The Non-Disruptive Code Load and Activation (NDCLA) has failed  
on this I/O blade.  
Action:  
None.  
(A6001.0003) (cmon: switch failed NDCLA)  
Meaning:  
The Non-Disruptive Code Load and Activation (NDCLA) has failed.  
The switch has performed a hard reset.  
Action:  
None.  
(A6001.0004) (cmon: Blade was removed during NDCLA)  
Meaning:  
An I/O blade was removed during the Non-Disruptive Code Load  
and Activation (NDCLA).  
Action:  
None.  
3-32  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
A
3.2  
Critical Events  
(C) (8100.0001) (LOG_MASK_NAME_SERVER) (Port: port_number) (Protocol violation from  
address FC_address)  
Meaning:  
There has been a name server protocol violation. Contact your  
authorized maintenance provider.  
(C) (8300.0006) (Zoning) (Dropping lock held by domain domain_ID, Merge requests  
outstanding)  
Meaning:  
Another switch has held the fabric zoning lock too long. It is being  
released to accommodate another fabric zoning request.  
(C) (8300.000A) (Zoning) (Fabric Busy, failing lock request from domain domain_ID)  
Meaning:  
Another switch in the fabric has requested the fabric zoning lock  
from this switch while this switch is processing zoning commands.  
(C) (8300.000B) (Zoning) (Failed to lock fabric, lock already held by switch with domain  
domain_ID)  
Meaning:  
Unable to complete the requested zoning command because fabric  
zoning lock is already held by another switch in the fabric.  
(C) (8300.000C) (Zoning) (Couldn't acquire lock from domain domain_ID)  
Meaning: Fabric may be changing, couldn't acquire lock. Wait for fabric to  
stabilize, try again.  
(C) (8300.000E) (Zoning) (Failing release of fabric lock held by switch with domain=  
domain_ID)  
Meaning:  
Unable to release fabric zoning lock which is held by another  
switch in the fabric.  
(C) (8300.000F) (Zoning) (Failed to lock fabric, lock already held with lock id lock_id)  
Meaning: The fabric is already locked.  
(C) (8400.0002) (Switch) (The switch is being reset - this may take several seconds)  
Meaning: The switch is being reset.  
(C) (8400.0003) (Switch) (The switch is being shutdown - this may take several seconds)  
Meaning: The switch is being gracefully shutdown.  
(C) (8400.0004) (Switch) (The switch is proceeding with a hotreset)  
Meaning: Hotreset is in progress.  
59060-02 B  
3-33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3 – Event Messages  
Critical Events  
S
(C) (8400.0005) (Switch) (The switch is now performing a hotreset)  
Meaning:  
Hot reset is in progress.  
(C) (8400.0006) (Switch) (Admin mode for user user_name was canceled by user  
user_name)  
Meaning:  
Admin authority mode was canceled by another user interface  
session that had the authority to do so.  
(C) (8400.0008) (Switch) (The switch will be reset in several seconds  
Meaning: The switch is being reset as a result of a command from a user  
interface.  
(C) (8400.0009) (Switch) (The switch will hardreset in several seconds)  
Meaning: A hard reset of the switch is pending.  
(C) (8400.000A) (Switch) (The switch will hotreset in several seconds)  
Meaning: A hot reset is pending.  
(C) (8400.000B) (Switch) (The switch will be shutdown several seconds)  
Meaning: The switch will be shutdown several seconds.  
(C) (8400.000C) (Switch) (Configuration is being restored - this could take several minutes)  
Meaning:  
When a complete configuration restore is done on a switch, a  
switch reset follows immediately to place the new configuration in  
effect.  
(C) (8400.000D) (Switch) (Attempted feature upgrade of features already installed)  
Meaning: The feature is already installed.  
(C) (8400.000E) (Switch) (Upgrading Licensed Ports to number_of_ports)  
Meaning:  
The number of licensed ports on the switch has been upgraded.  
(C) (8400.000F) (Switch) (Attempted Licensed Port upgrade of ports that are already  
licensed)  
Meaning:  
The switch has already been upgraded to the number of licensed  
ports.  
(C) (8400.0011) (Switch) (The switch will be reset in several seconds due to a config  
restore)  
Meaning:  
Switch management is processing a config restore command.  
(C) (8400.0012) (Switch) (I/O blade in slot slot_number has been inserted into chassis)  
Meaning: An I/O blade has been inserted into the chassis.  
3-34  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
A
(C) (8400.0014) (Switch) (I/O blade in slot slot_number has been removed from chassis)  
Meaning: An I/O blade has been removed from the chassis.  
(C) (8400.0015) (Switch) (The switch will be reset in several seconds)  
Meaning: The switch is being reset as a result of a command from a user  
interface.  
(C) (8400.0016) (Switch) (Group members are being saved - this may take several  
seconds)  
Meaning:  
Group members are being saved in the security database.  
(C) (8400.0017) (Switch) (Security edit session has been preempted by a security merge)  
Meaning:  
A security merge has occurred and the security edit session has  
been cancelled.  
(C) (8400.001C) (Switch) (The switch is being reset - this may take several seconds)  
Meaning: The switch is being reset.  
(C) (8400.001D) (Switch) (The switch is being shutdown - this may take several seconds)  
Meaning: The switch is being shutdown.  
(C) (8400.0027) (Switch) (Invalid user account_name attempted to log into switch)  
Meaning: Invalid user login attempt.  
(C) (8400.0028) (Switch) (Invalid user account_name attempted to log into switch)  
Meaning: Invalid user login attempt.  
(C) (8400.0029) (Switch) (User account_name attempted to log into switch with an incorrect  
password)  
Meaning:  
Invalid user login attempt.  
(C) (8400.002A) (Switch) (User account_name attempted to log into switch with an incorrect  
password)  
Meaning:  
Invalid user login attempt.  
(C) (8400.002E) (Switch) (number_of_zone_members zone members are being saved - this  
may take several seconds)  
Meaning:  
Saving a large zoning database takes some time.  
59060-02 B  
3-35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
S
(C) (8400.002F) (Switch) (Zoning database of over 3000 zone members may damage some  
vendors’ switches, if you have other vendor’s switches in your fabric,  
please refer to their switch manual/documentation to see what zone member  
limits the switch supports)  
Meaning:  
You have a large database on the switch consisting of over 3000  
zone members. Not all vendors support a large configuration such  
as this, and so this could cause a problem in mixed fabrics.  
(C) (8400.0030) (Switch) (Zoning edit session has been preempted by a zoning merge)  
Meaning:  
A zoning edit session has been preempted by a zone merge. The  
zoning edit session has been canceled.  
(C) (8400.003B) (Switch) (Creating the support file - this will take several seconds)  
Meaning:  
The switch is creating a support file. This takes a few seconds to  
complete.  
(C) (8400.003C) (Switch) (Network setup is changing - may lose connection - admin being  
released automatically)  
Meaning:  
Changes have been made to the network configuration which may  
interrupt your connection to the switch.  
(C) (8400.0042) (Switch) (Warning - deleting the active zoneset may cause fabric isolation)  
Meaning:  
Deleting the active zone set from the zoning database could isolate  
all switches in the fabric.  
(C) (8400.0043) (Switch) (Warning - clearing the active zoneset may cause fabric isolation)  
Meaning:  
Clearing all zoning definitions from the active zone set could isolate  
all switches in the fabric.  
(C) (8400.0044) (Switch) (A reset is required since a Power On Self Test (POST) has never  
run on these ports)  
Meaning:  
After upgrading ports, it may be necessary to reset the switch so  
that the POST can run on the newly licensed ports.  
(C) (8400.0045) (Switch) (Upgrading License for 4G capability)  
Meaning: Installation of the license key that grants 4-Gbps transmission  
speed capability to the Fibre Channel ports is in progress.  
(C) (8400.0046) (Switch) (Upgrading License for multiple ISL capability)  
Meaning: The switch has been upgraded to allow for multiple inter-switch  
links.  
(C) (8400.0047) (Switch) (New licenses are being installed  
Meaning: New licenses are being installed.  
3-36  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
A
(C) (8400.0049) (Switch) (The Configuration Wizard from ip_address is exiting - switch  
configuration may have changed)  
Meaning:  
Changes have been made to switch that may result in loss of  
communication with the switch.  
(C) (8400.004B) (Switch) (Attempted to license modes on an unsupport switch type)  
Meaning:  
An attempt was made to install a license key for a feature that is  
not supported on the switch.  
(C) (8400.004C) (Switch) (Services setup is changing - may lose connection - admin being  
released automatically)  
Meaning:  
The Services configuration is changing and this may result in the  
loss of a connection.  
(C) (8400.004D) (Switch) (ntpdate: no server suitable for synchronization found)  
Meaning: The NTP server was not found.  
(C) (8400.004E) (Switch) (ntpdate: : synchronization lost)  
Meaning:  
The NTP Server synchronization was lost.  
(C) (8400.004F) (Switch) (Upgrading License for Interop_2 mode capability  
Meaning:  
The license upgrade was successful.  
(C) (8400.0050) (Switch) (Upgrading License allowing manufacturing setup mode  
capability)  
Meaning:  
The license upgrade was successful.  
(C) (8400.0052) (Switch) (Upgrading License for EFCM capability)  
Meaning: The license upgrade was successful.  
(C) (8400.0053) (Switch) (The switch WWN is being upgraded)  
Meaning: The license upgrade was successful.  
(C) (8400.0054) (Switch) (radius: All RADIUS servers failed to respond)  
Meaning:  
None of the RADIUS servers configured responded. Check  
RADIUS server configuration.  
(C) (8400.0057) (Switch) (User login (user_name) is being closed - Telnet connections have  
been disabled  
Meaning:  
A Telnet session has closed.  
59060-02 B  
3-37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
S
(C) (8400.0058) (Switch) (User (user_name) is using their initial/default password)  
Meaning:  
The specified user has not changed their password from its initial  
value.  
(C) (8400.005D) (Switch) (Upgrading License for SANdoctor)  
Meaning:  
The SANdoctor bundle license was applied successfully.  
(C) (8400.0062) (Switch) (New firmware has been installed.)  
Meaning:  
New firmware was successfully installed.  
(C) (8400.0065) (Switch) (Warning-When leaving the Diagnostics AdminState of the switch  
an automatic reset of the switch will occur. The switch will come back up in  
the configured AdminState.)  
Meaning:  
The switch automatically undergoes a hard reset after leaving the  
Diagnostics administrative state.  
(C) (8400.0066) (Switch) (Warning-When leaving the Diagnostics AdminState of a blade, an  
automatic reset of the blade will occur. The blade will come back up in the  
configured AdminState.)  
Meaning:  
I/O blade is undergoes a hard reset after leaving the Diagnostics  
administrative state.  
(C) (8400.0067) (Switch) (Warning-When leaving the Diagnostics AdminState of the switch  
an automatic reset of the switch will occur. The switch will come back up in  
the configured AdminState.)  
Meaning:  
The switch is entering Diagnostics state and will automatically  
undergo a hard reset. The switch will return to the configured  
administrative state after leaving the Diagnostics administrative  
state.  
(C) (8400.0068) (Switch) (Warning-When leaving the Diagnostics AdminState of a blade, an  
automatic reset of the blade will occur. The blade will come back up in the  
configured AdminState.)  
Meaning:  
The I/O blade is entering Diagnostics state and will automatically  
undergo a hard reset. The I/O blade will return to the configured  
administrative state after leaving the Diagnostics administrative  
state.  
3-38  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
A
(C) (8400.0069) (Switch) (Warning-When leaving the Diagnostics AdminState of the  
primary CPU blade, an automatic reset of the blade will occur. The blade and  
the switch will come back up in the configured AdminState.)  
Meaning:  
The primary CPU blade is entering Diagnostics state and will  
automatically undergo a hard reset. The I/O blade will return to the  
configured administrative state after leaving the Diagnostics  
administrative state.  
(C) (8400.006A) (Switch) (Upgrading License for Fabric Security)  
Meaning:  
The Fabric Security Bundle license was applied successfully.  
(C) (8400.006B) (Switch) (Upgrading License for CLI Extended Credits capability)  
Meaning:  
The CLI Extended Credits license was applied successfully.  
(C) (8600.0009) (PortApp) (Port: port_number) (Link reset (LR) to be performed on port  
port_number.)  
Meaning:  
The port will perform a link reset (LR) due to loss of credit issue.  
(C) (8600.000A) (PortApp) (Port: port_number) (Link reset (LR) to be performed on port  
port_number.)  
Meaning:  
The port will perform a link reset (LR) due to loss of credit issue.  
(C) (8600.000B) (PortApp) (Port: port_number) (Link reset (LR) to be performed on port  
port_number.)  
Meaning:  
The port will perform a link reset (LR) due to loss of credit issue.  
(C) (8600.0013) (PortApp) (Invalid vendor data from media device for port port_number)  
Meaning:  
The switch could not read and verify the media module ID. This  
may indicate a discovery error or a bad checksum in the serial ID.  
Other possibilities include an improperly installed media module or  
an internal media I/O hardware fault.  
(C) (8600.0014) (PortApp) (Invalid vendor data from media device for port port_number)  
Meaning:  
Switch could not read and verify the media module ID. This could  
be caused by a media discovery error, a bad checksum in the  
media serial ID, an improperly installed media, or an internal media  
I/O hardware fault.  
(C) (8600.0015) (PortApp) (Unresponsive device alpa on port port_number removed from  
the fabric.)  
Meaning:  
A device on the loop port did not take a OPN off the loop destined  
for it. This suggests either the device has been physically removed  
or is faulty. It has been removed from the fabric nameserver.  
59060-02 B  
3-39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
S
(C) (8600.0016) (PortApp) (Online port(s) port_numbers were reset due to disruption during  
hot reset.)  
Meaning:  
Some ports were disrupted during hot reset operation due to  
events causing disruption.  
(C) (8600.0017) (PortApp) (External port license count exceeded, downing external port  
port_number)  
Meaning:  
The named external port is down because the number of licensed  
external ports has been exceeded.  
(C) (8600.0018) (PortApp) (External port license became available, re-starting downed  
external ports)  
Meaning:  
An external port that was previously down because of insufficient  
port licenses is now online.  
(C) (8600.0019) (PortApp) (Internal port license count exceeded, downing internal port  
port_number)  
Meaning:  
A device attempted to login to an internal port, but a license was  
not available. A license upgrade may be required, or a license may  
be release by downing ports.  
(C) (8600.001A) (PortApp) (Internal port license became available, re-starting downed  
internal ports)  
Meaning:  
A license has become available and ports that had been previously  
downed to due to unavailable licenses will be restarted.  
(C) (8700.0007) (EPort) (Port: port_number) (Received frame from address not in Access  
Control List (ACL) hard zone (src address = FC_address, dest address =  
FC_address))  
Meaning:  
The destination for the receive frame is in an ACL zone and the  
source is not. The frame will not be forwarded.  
(C) (8700.000D) (EPort) (Port: port_number) (Resetting Inter-Switch Link (ISL), a time out  
value has been reconfigured.)  
Meaning:  
The Resource Allocation (R_A_TOV) or Error Detect (E_D_TOV)  
timeout value has been reconfigured. E_Ports will be automatically  
reset to inform the neighbor switch of the change.  
(C) (8700.000E) (EPort) (Port: port_number) (InteropCredit value was reconfigured,  
resetting port.)  
Meaning:  
The InteropCredit parameter has changed. The affected port will  
be automatically reset.  
3-40  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Critical Events  
A
(C) (8700.000F) (EPort) (Port: port_number) (Broadcast frame received & broadcast  
disabled, discarding broadcast frames.)  
Meaning:  
Broadcast is disabled and the switch has received a broadcast  
frame. Enable broadcast to receive broadcast frames.  
(C) (8700.0010) (EPort) (Port: port_number) (Inter-Switch Link (ISL) unstable. ISL init will be  
held back until ISL up time is 5 seconds)  
Meaning:  
The ISL is unstable indicating that the media module or the cable is  
bad.  
(C) (8700.0011) (Eport) (Port: port_number) (Connection failure, remote switch not  
compatible)  
Meaning:  
The remote switch is not compatible with the local switch. The  
E_Port cannot exchange switch capabilities with the remote switch.  
(C) (8700.0012) (Eport) (Port: port_number) (Connection failure, fabric limited to two  
switches)  
Meaning:  
The switch cannot be connected to the fabric due to a license  
restriction.  
(C) (8700.0013) (Connection failure, fabric limited to two switches)  
Meaning: The switch cannot be connected to the fabric due to license  
restriction.  
(C) (8F00.000C) Fabric Status status  
Meaning: The severity of the fabric status has changed. The description field  
will show the reason for fabric status.  
(C) (8F00.000D) Switch Status status  
Meaning: The severity of the switch status has changed. The description field  
will show the reason for the switch status.  
(C) (8F00:000E) Link Status status  
Meaning: The severity of the link status has changed. The description field  
will show the reason for link status.  
59060-02 B  
3-41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Warning Events  
S
3.3  
Warning Events  
(W) (8400.0007) (Switch) (Attempted unauthenticated login username account_name)  
Meaning:  
A login was attempted with an account name that was not in the list  
of allowable users of Switch Management.  
(W) (8400.0018) (Switch) (User (user_name>) login rejected - maximum logins already in  
use)  
Meaning:  
The attempted login was rejected because of too many sessions  
currently in use. There may be multiple GUI or API sessions open  
on the switch which are no longer being used.  
(W) (8300.0011) (User) Releasing Lock held too long by domain_ID.  
Meaning: A lock was held by another switch for too long. The lock will be  
automatically released.  
(W) (8300.0012) (User) SFC received with unknown operation operation_code.  
Meaning:  
Received a frame from another switch with an unknown Staged  
Fabric Configuration (SFC) operation code. Ignoring operation.  
(W) (8300.0013) (User) Unlock failed, resource unavailable, will retry.  
Meaning:  
A fabric unlock performed through a Release Change  
Authorization failed because the switch ran out of buffer memory.  
The unlock mechanism will retry when memory is freed up.  
(W) (8300.0014) (User) Bad release change authorization response received from switch  
with domain ID domain_ID  
Meaning:  
The switch is attempting to do a fabric unlock through a Release  
Change Authorization request, but a remote switch indicated a  
failure. This switch will proceed with the unlock.  
(W) (8300.0015) (User) No RCA response received from domain_ID, proceeding with unlock  
Meaning:  
The switch never got a reply from a message sent to release the  
change authorization. The release of change authorization will  
occur regardless.  
(W) (8300.0016) (User) Zoning activation failed, resource limitation  
Meaning: This switch is attempting to activate a zone set but cannot do so  
due to a resource problem.  
3-42  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3 – Event Messages  
Warning Events  
A
(W) (8400.0018) (Switch) (User account_name login rejected - maximum logins already in  
use)  
Meaning:  
The attempted login was rejected because there are too many  
sessions. There may be switch management sessions open on the  
switch that are no longer in use.  
(W) (8400.001F) (Switch) (User account_name login rejected - maximum logins already in  
use)  
Meaning:  
The attempted login was rejected because there are too many  
sessions. There may be switch management sessions open on the  
switch that are no longer in use.  
(W) (8400.0020) (Switch) (User account_name login rejected - maximum logins already in  
use)  
Meaning:  
The attempted login was rejected because there are too many  
sessions. There may be switch management sessions open on the  
switch that are no longer in use.  
(W) (8400.0021) (Switch) (User account_name login rejected - maximum logins already in  
use)  
Meaning:  
The attempted login was rejected because there are too many  
sessions. There may be switch management sessions open on the  
switch that are no longer in use.  
(W) (8400.0034) (Switch) (Port port_number was Downed before hotreset due to excessive  
errors - still DOWNED)  
Meaning:  
A port was disabled by the threshold monitoring application before  
the hot reset, and is still disabled after the hot reset.  
(W) (8400.0035) (Switch) (Retrying port port_number that was Downed due to excessive  
errors)  
Meaning:  
A port that was disabled by the threshold monitoring application is  
periodically retried to see if the error conditions have been cleared.  
(W) (8400.003D) (Switch) (Invalid user (user_name) attempted to log into switch)  
Meaning: Invalid user login attempt.  
(W) (8700.0009) (EPort) (Port: port_number) (Inter-Switch Link (ISL) communication error)  
Meaning: The remote switch has lost the local switch’s identity.  
59060-02 B  
3-43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Informative Events  
S
(W) (8700.000A) (EPort) (Port: port_number) (No response from remote switch, resetting  
Inter-Switch Link (ISL))  
Meaning:  
No communication has been received from the remote switch for  
some time indicating that it may not be functioning properly. The  
E_Port will be reset in an attempt to reestablish the ISL.  
(W) (8F00.000C) (Fabric Status status)  
Meaning: The severity of the fabric status has changed. The description field  
will show the reason for fabric status.  
(W) (8F00.000D) (Switch Status status)  
Meaning: The severity of the switch status has changed. The description field  
will show the reason for the switch status.  
(W) (8F00:000E) (Link Status status)  
Meaning: The severity of the link status has changed. The description field  
will show the reason for link status.  
3.4  
Informative Events  
(I) (8200.0001) (mserver) (Hotreset is not permitted at this time, try again later)  
Meaning:  
The switch was busy at the time of the attempted hot reset. Try the  
hot reset again later.  
(I) (8200.0002) (mserver) (Port: port_number) (Rejecting request from address FC_address,  
inband management is disabled on port port_number)  
Meaning:  
A Management Server command was received on a port that is  
configured to be disabled for inband management requests.  
(I) (8200.0100) (mserver) (Cannot map number_of_characters characters to Switch  
Symbolic Name (max number_of_characters))  
Meaning:  
The RIELN management server command was processed, and the  
Interconnect Element Logical Name was registered. However, the  
registered name is of greater length than the maximum length  
allowed for the Switch Symbolic Name, so therefore the Switch  
Symbolic Name was not changed to match the registered name.  
(I) (8200.0101) (mserver) (Cannot map non-printable characters to Switch Symbolic Name)  
Meaning:  
The RIELN management server command was processed, and the  
Interconnect Element Logical Name was registered. However, the  
registered name contains unprintable characters. These characters  
are not allowed for the switch symbolic name, therefore the switch  
symbolic name was not changed to match the registered name.  
3-44  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
3 – Event Messages  
Informative Events  
A
(I) (8200.0200) (mserver) (Rejecting request (GZM) for zone zone_name containing  
unsupported alias member(s)  
Meaning:  
The fabric zone server command GZM (Get Zone Member) was  
rejected because the requested zone member was an alias which  
is not defined in GS-3.  
(I) (8200.0201) (mserver) (Rejecting request command:command)  
Meaning: A fabric zone server command was rejected for the reason detailed  
in the message. This can be caused by two users attempting to  
configure the switch or zoning database at the same time. Contact  
your authorized maintenance provider if the reason for the failure is  
not clear.  
(I) (8200.0202) (mserver) (Rejecting request (GZS) for zone set zone_set_name containing  
unsupported alias member(s))  
Meaning:  
The fabric zone server command GZS (Get Zone Set) was rejected  
because the requested zone set contains one or more members  
that are aliases. Since aliases are not defined in GS-3, the request  
could not be completed.  
(I) (8200.0300) (mserver) (Cannot register HBA World Wide Name (WWN) device_WWN,  
FDMI database has reached its configured limit.)  
Meaning:  
The switch contains a database that is configured to allow a certain  
number of HBAs to register Fabric Device Management Interface  
(FDMI) information with this switch. An HBA has attempted to  
register its FDMI information with the switch, but allowing it to do so  
would cause the FDMI database to exceed the configured limit.  
(I) (8200.0301) (mserver) (Port: port_number) (Rejecting FDMI request from address  
FC_address on port port_number; FDMI is configured as disabled.)  
Meaning:  
The Fabric Device Management Interface (FDMI) server on this  
switch has been configured disabled so any FDMI requests  
received by the switch will be rejected.  
(I) (8300.0004) (zoning) (New Active ZoneSet zone_set_name)  
Meaning: A new zone set has been activated.  
(I) (8300.0007) (zoning) (Fabric lock held by domain domain_ID, hotreset not permitted)  
Meaning:  
Another switch has acquired our fabric zoning lock. Zoning request  
is about to occur. Retry hotreset after fabric zoning lock is released.  
(I) (8300.0008) (zoning) (Processing zoning requests, Checkpoint not permitted)  
Meaning:  
Another switch has acquired our fabric zoning lock. Zoning request  
is about to occur. Retry hotreset after fabric zoning lock is released.  
59060-02 B  
3-45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Informative Events  
S
(I) (8300.0009) (Zoning) (Reading zoning database, Checkpoint not permitted)  
Meaning:  
A change to the fabric zoning data base forced a read of the data  
base to occur. Retry hotreset after read is complete  
(I) (8300.0010) (Zoning) (Removing all inactive zoning objects)  
Meaning: All zones that were members of the previously active zone set are  
being removed from the zoning database.  
(I) (8400.0001) (Switch) (Modifying configured DomainID domain_ID to negotiated value  
domain_ID)  
Meaning:  
The configuration is changing. The configured domain ID is  
changed to the negotiated value.  
(I) (8400.0006) (Switch) (Admin mode for user account_name was canceled by user  
account_name)  
Meaning:  
An Admin session was canceled by another user interface session  
that had the authority to do so.  
(I) (8400.001A) (Switch) (Admin access has timed out for user account_name)  
Meaning:  
The Admin session opened by the named user has timed out due  
to inactivity.  
(I) (8400.0022) (Switch) (Successful login user account_name with admin privilege)  
Meaning:  
A user with admin authority has successfully logged into the  
switch. The IP address of the user is unknown.  
(I) (8400.0023) (Switch) (Successful login user account_name with admin privilege)  
Meaning:  
A user with admin authority has successfully logged into the  
switch. The IP address of the user is unknown.  
(I) (8400.0024) (Switch) (Successful login user account_name without admin privilege)  
Meaning:  
A user without admin authority has successfully logged into the  
switch. The IP address of the user is unknown.  
(I) (8400.0025) (Switch) (Successful login user account_name without admin privilege)  
Meaning:  
A user without admin authority has successfully logged into the  
switch. The IP address of the user is unknown.  
(I) (8400.0026) (Switch) (A zoning configuration edit session has been canceled)  
Meaning:  
The zoning configuration edit session has been canceled as a  
result of the Zoning Cancel command.  
3-46  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Informative Events  
A
(I) (8400.002B) (Switch) (User login account_name is being closed - In-Band connections  
have been disabled)  
Meaning:  
The session has been closed as a result of a configuration change.  
(I) (8400.002C) (Switch) (User login session session_ID user account_name has timed out)  
Meaning: A user login session has ended because of inactivity.  
(I) (8400.0036) (Switch) (Hotreset not permitted at this time, try again later)  
Meaning: Conditions exist that will not allow a hotreset. Try again later.  
(I) (8400.0037) (Switch) (VIEnable automatically set to False since MFSEnable has been set  
to True)  
Meaning:  
Setting the Set Config Port parameter MFSEnable to True  
automatically sets the Set Config Port parameters VIEnable and  
LCFEnable to False.  
(I) (8400.0038) (Switch) (LCFEnable automatically set to False since MFSEnable has been  
set to True)  
Meaning:  
Setting the Set Config Port parameter MFSEnable to True  
automatically sets the Set Config Port parameters VIEnable and  
LCFEnable to False.  
(I) (8400.0039) (Switch) (MFSEnable automatically set to False since VIEnable has been set  
to True)  
Meaning:  
Setting the Set Config Port parameter VIEnable to True  
automatically sets the Set Config Port parameter MFSEnable to  
False.  
(I) (8400.003A) (Switch) (MFSEnable automatically set to False since LCFEnable has been  
set to True)  
Meaning:  
Setting the Set Config Port parameter LCFEnable to True  
automatically sets the Set Config Port parameter MFSEnable to  
False.  
(I) (8400.003E) (Switch) (Readjusting TempMonitoringWarning from value C to value C)  
Meaning:  
The temperature threshold at which the switch issues a warning  
alarm is being changed.  
(I) (8400.0040) (Switch) (Readjusting TempMonitoringFailure from value C to value C)  
Meaning:  
The temperature threshold at which the switch issues a failure  
alarm is being changed.  
59060-02 B  
3-47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Informative Events  
S
(I) (8400.0048) (Switch) (A CIM edit session has been canceled)  
Meaning:  
A Common Information Model (CIM) edit session has been  
cancelled.  
(I) (8600.0007) (PortApp) (Port: port_number) (Cancelling Online Test)  
Meaning: The online test was canceled.  
(I) (8700.0002) (EPort) (In Fabric Reconfiguration)  
Meaning: Changes to the switch configuration are in progress.  
(I) (8700.0003) (EPort) (Topology change, switch with domain ID domain_ID joined the  
fabric)  
Meaning:  
A switch with the given domain ID has joined the fabric.  
(I) (8700.0004) (EPort) (Port: port_number) (Remote Switch World Wide Name (WWN) is  
switch_WWN)  
Meaning:  
A switch with the given domain ID has been discovered on the  
given port.  
(I) (8700.0005) (EPort) (Port: port_number) (Inter-Switch Link (ISL) Offline)  
Meaning:  
The given E_Port is offline possibly due to a loss of  
synchronization.  
(I) (8700.0006) (EPort) (Port: port_number) (Reinitializing port previously isolated for  
reason reason)  
Meaning:  
The E_Port that previously isolated for the stated reason is now  
reinitializing.  
(I) (8700.0008) (EPort) (Link State Record (LSR) aged out for domain ID =domain_ID)  
Meaning:  
A record in the Link State Database (LSDB) is being aged out. It  
will no longer be in the LSDB.  
(I) (8700.000B) (EPort) (Hotreset prohibited, fabric is busy.)  
Meaning: A hot reset is not possible when configuration changes are being  
made anywhere in the fabric.  
(I) (8700.000C) (EPort) (Hotreset prohibited, fabric is busy.)  
Meaning: A hot reset is not possible when configuration changes are being  
made anywhere in the fabric.  
(I) (8F00.0006) Fabric Removed  
Meaning: The user has removed a fabric from the application.  
3-48  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Informative Events  
A
(I) (8F00.0007) Switch Added  
Meaning:  
The application fabric discovery process has discovered a new  
switch in the fabric.  
(I) (8F00.0008) Switch Removed  
Meaning:  
The user has removed a switch from the display.  
(I) (8F00.0009) Link Added  
Meaning:  
The application fabric discovery process has discovered a new  
inter-switch link (ISL) in the fabric  
(I) (8F00.000A) Link Removed  
Meaning: A link has been removed from the display. This is either because  
the fabric discovery process has discovered that the link is no  
longer in the fabric, or because the user has deleted the link  
manually.  
(I) (8F00.000B) Login Changed  
Meaning: The login to the fabric has changed. The description field will show  
the reason for the change in the login.  
(I) (8F00.000C) Fabric Status status  
Meaning: The severity of the fabric status has changed. The description field  
will show the reason for fabric status.  
(I) (8F00.000D) Switch Status status  
Meaning: The severity of the switch status has changed. The description field  
will show the reason for the switch status.  
(I) (8F00:000E) Link Status status  
Meaning: The severity of the link status has changed. The description field  
will show the reason for link status.  
59060-02 B  
3-49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3 – Event Messages  
Informative Events  
S
Notes  
3-50  
59060-02 B  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q See Home Security System QT428 803 User Guide
Radio Shack Two Way Radio TRC 236 User Guide
RCA CRT Television 27F520T User Guide
RCA DVD Player DRC310N User Guide
Ricoh Dehumidifier AP3800C User Guide
Roberts Radio MP3 Player MP 30 User Guide
RocketFish Computer Hardware RF 71SDCD User Guide
Samsung Cell Phone DM S105 User Guide
Sanyo Heat Pump APR RZP680BAB User Guide
Scotsman Ice Ice Maker HD30 User Guide