P/N 4411-0019
CC-100
Coolant
Circulator
Operation
manual
Manual Version 1
Revision B
July 1, 1998
ꢀꢁꢁꢂꢂꢃꢄꢄꢂꢅꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 Introduction ........................................................................................ 5
Description..........................................................................................................................5
Specifications......................................................................................................................5
Chapter 2 Warnings............................................................................................. 7
Introduction.........................................................................................................................7
Chapter 3 Installation .......................................................................................... 9
Inspection............................................................................................................................9
Spare Parts Bag...................................................................................................................9
Connections and Checks.....................................................................................................9
Chapter 4 Maintenance ..................................................................................... 11
Air Filter............................................................................................................................11
Coolant..............................................................................................................................11
Coolant Pump....................................................................................................................11
Schematic Diagrams .........................................................................................................11
Warranty and Service........................................................................................ 15
Warranty............................................................................................................................15
Equipment Repairs............................................................................................................15
Contact Information..........................................................................................................16
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introduction
Description
The Model CC-100 Coolant Circulator is a universal water-to-air heat exchanger. It
transfers heat from any heat source into the air. It was designed primarily for removing
heat from thermoelectrically cooled CCD cameras. A magnetic drive coolant pump
circulates coolant to the CCD camera (or any other heat source). This coolant passes
through the hot side of the camera, which raises the temperature of the coolant. The
heated coolant is then returned to the radiator of the CC-100. An internal fan forces air
through the radiator reducing the temperature of the coolant by convection. The coolant
then returns to the pump and repeats the cycle. This efficient closed cycle process can
maintain the temperature of the coolant within a few degrees above ambient temperature.
Specifications
Note: All test data and specifications shown are based on pumping water and are
guidelines only. Specifications will vary depending on specific fluid, temperatures, and
other operating conditions.
Coolant: Water, water/ethylene glycol (50% solution), automotive antifreeze and other
inert liquids with viscosity approximately that of water.
Capacity: Approximately 0.9 quart ( 0.85 liter), exclusive of external coolant lines and
device to be cooled.
Pressure and Flow
Maximum head pressure 13 feet (4 meters), 6.38 PSI ( 44 kPa), with zero
flow.
Maximum flow is 5 gallons per minute (19 liters/min) with zero head pressure.
A flow rate of 1 gallon per minute (3.8 liters/min at 5 PSI (34.5 kPa).
In a typical application with 20 feet (6 meters) of 3/16 (4.76 mm) I.D. polyurethane
tube, and 8 Swagelock quick connect connectors. The flow rate will be 1 pint per
minute ( 0.5 liters/min).
In a typical application with 20 feet (6 meters) of 3/16 (4.78mm) I.D. polyurethane tube
with only tube connectors. The flow rate will be 1 quart per minute ( 0.95 l/min).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
CC-100 Coolant Circulator Manual
Cooling Capacity
Version 1.B
Temperature rises approximately 0.03°C per watt (3.4 btu/hr). Based on a typical
flow rate of between 0.5 (0.47 liter) to 1 quart (0.95 liter) per minute and a thermal
load of 100 watts (341 btu/hr).
When using a CC-100 to cool a PI detector, the coldest attainable temperature should
be reduced by no more than two degrees compared with using tap water at ambient
temperature.
Operating Environment
Temperature
Minimum: 0°F (-18°C). Avoid freezing coolant.
Maximum: 120°F (49°C).
Humidity: Avoid condensation
Clearance
Front: 6 inches (150 mm) minimum
Rear: 12 inches (300 mm) minimum
Side: 1 inch (20 mm) minimum
Power Requirements: 50/60 Hz
2 A @ 105V to 125V AC (standard)
2 A @ 90V to 110 V AC (factory installed option)
1 A @ 210 V to 250 V AC (factory installed option)
Mechanical
Dimensions
D, W, H: 12½ 318mm) × 15¾ (400mm) × 8¼ (210 mm)
Weight (without coolant)
16 lb (7.3 kg) without transformer, standard
19 lb (8.6 kg) with optional transformers for either 100V or 230V AC operation
Fluid Interface
Two ¼ female NPT tapped threads provided at the Inlet and Outlet on the rear
panel.
Two ¼ male NPT connectors to ¼ swage tube fittings with two 3 (76mm) by ¼
OD copper tubes provided standard.
Two ¼ plastic Swagelock tube plugs are provided standard.
Options
Tube accessory kit with eight Swagelock quick disconnect connectors and 20 feet
(6 m) of polyurethane tubing ¼ OD by 3/16 ID.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Warnings
Introduction
This chapter contains cautions and notes concerning initial setup and operation of your
system. Of course, reading this section should not replace reading the entire manual. The
rest of the manual contains complete procedures for installing and operating your
system, as well as a more detailed explanation of the following warnings
WARNING
Verify that the line voltage and fuse ratings are compatible before turning
on the system. Voltage applied outside the range may damage the apparatus! The line
voltage is not selectable. The unit must be modified at the factory for the desired
operating voltage. The Model number on the rear panel indicates the line voltage with
which this unit is designed to operate. The Model CC100-115V may be used for line
voltages between 105 and 125 V AC, 50 or 60 Hz. The Model CC100-230 V may be
used for line voltages between 210 and 250 V AC, 50 or 60 Hz. The Model CC100-100V
may be used for line voltages between 90 and 100 V AC, 50 to 60 Hz. The fuse ratings
are labeled on the rear panel, except Model CC100-100V. For the CC100-100V the fuse
rating is 2 A at 120V AC.
WARNING
WARNING
Protective grounding must be maintained. Protective grounding could become
ineffective in apparatus possibly damaged during shipping. Until safety has been verified
by Princeton Instruments, Inc, such damaged apparatus should not be used. Tag the unit
appropriately to warn any potential user of such a danger.
A socket outlet provided with the necessary earth ground contact must be
used. Any extension cord or adapters used must also comply with these safety
requirements. If the supplied cord plug is not compatible with the power socket, a
substitute plug of a compatible design should replace it. Replacement power cords or
power plugs must have the same polarity as those of the original equipment to avoid
hazard due to electrical shock. Disconnecting the protective earth terminal inside or
outside the apparatus is prohibited.
Never run the CC-100 without coolant in the reservoir. Although the magnetic
pump can withstand short intervals of operation without coolant, doing so will shorten
the life of the pump.
CAUTION
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8
CC-100 Coolant Circulator Manual
Version 1.B
Never allow coolant to freeze. For storage, shipping and operating, a mixture of
water/antifreeze or equivalent should be used to prevent freezing and corrosion. Any
commercial brand antifreeze, recommended for automotive use, may be used in the CC-
100. It is especially important to prevent freezing during shipping, since the temperature
to which the CC-100 will be exposed will not be under control. Since it is very difficult
to drain the CC-100 completely, it is strongly advised to fill with an antifreeze solution
of sufficient concentration to prevent freezing. Circulate coolant solution for at least five
minutes prior to draining in preparation for shipment.
CAUTION
WARNING
Do not operate the unit with the top cover removed. The fan blades are exposed
inside the CC-100. Primarily, personal injury will result if the operator comes in contact
with the rotating fan blades. Secondarily, running the CC-100 with the covers removed
prohibits air flow through the radiator. The temperature of the coolant will rise, since
there will be no exchange of heat between the coolant and the air. The rise in
temperature may not damage the CC-100, but may overheat and cause damage to the
device that is being cooled.
WARNING
WARNING
Check all coolant hoses and connectors for leaks. Although the unit is tested
for leaks at the factory, a visual check for leaks should be made whenever the top cover
is removed. If you observe any coolant leakage, turn off the CC-100 at once. Any
leakage inside the CC-100 is an electrical hazard and should be repaired prior to use.
Do not pressurize the coolant system. The maximum pressure generated inside of
the CC-100 is 6 PSI ( 41.4 kPa). There should be zero pressure in the system when
the CC-100 is not in operation. Applying any external pressure to the system is not
recommended and will void the warranty.
WARNING
WARNING
WARNING
There is no coolant flow indication or protection. It is recommended that the
user sense coolant flow and provide protection to the device being cooled, if coolant
flow is interrupted.
Do not operate the system using 100% ethylene glycol. A high concentration
solution is not able to carry away the heat created by the detector. A 50% solution is
recommended.
During shipment spare parts are taped inside of the CC-100 to the top support bracket.
These parts must be removed prior to applying power to the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Installation
Inspection
When unpacking the CC-100, it should be inspected for any obvious shipping damage.
Any shipping damage noted should be reported without delay to both the carrier and to
Princeton Instruments, Inc., before operating the system. In case of shipping damage, all
shipping material should be saved. Princeton Instruments, Inc. and the shipping carrier
should be notified immediately. Otherwise Princeton Instruments, Inc. will consider the
damage due to abuse. If external damage is unnoticeable, but system specifications are
not met, internal damage has probably occurred.
Spare Parts Bag
Remove the top cover of the CC-100 by removing the four screws and washers from
each side of the top cover. Remove the package of spare parts containing the copper
tubes, nuts, etc. from the inside of the CC-100. Inspect inside the instrument for internal
damage. Again, in case of shipping damage, all shipping material should be saved.
Princeton Instruments, Inc. and the shipping carrier should be notified immediately.
Otherwise Princeton Instruments, Inc. will consider damage as due to abuse.
Connections and Checks
➧ Make all the coolant plumbing connections between the CC-100 and the device to be
cooled.
➧ Remove the lid from the reservoir and fill it with a water/antifreeze mixture of
sufficient concentration to prevent freezing. Be careful not to spill any coolant inside
of the instrument.
➧ Turn the power on and allow the coolant to circulate.
➧ Refill the reservoir as required until all the air is out of the system DO NOT
OVERFILL the reservoir.
➧ Tighten the lid onto the reservoir.
➧ Check for both internal and external leaks. Generally, four or five minutes of
operation should be sufficient to determine if any leaks are present.
➧ Turn the power off.
➧ Place the plastic tube plugs in a bag and secure inside the chassis (these parts will be
needed if you have to return the instrument for repair). Install the top cover and
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
CC-100 Coolant Circulator Manual
Version 1.B
secure it with the eight screws and washers removed above. Installation is now
complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Maintenance
Air Filter
The frequency of cleaning depends on the environment around the CC-100. Usually,
whenever the velocity of air coming out of the CC-100 decreases, it is time to clean the
filter. Another indication is the rise in the outlet temperature above ambient. Normally
this temperature will be within a few degrees of ambient. The air filter is located in front
of the radiator. The easiest way of cleaning the filter is to vacuum it from the outside
without any disassembly of the CC-100. If this is not possible, the filter can be cleaned
by removing the top cover, removing the brackets holding the radiator in place, tilting
the top of the radiator away from the rear panel and removing the air filter. Once the
filter is removed, wash out the filter with tap water and allow it to dry before reinstalling
it.
Coolant
The antifreeze coolant needs to be maintained annually. A complete flush and refill is
recommended per instructions on the particular brand of antifreeze selected.
Coolant Pump
The top cover needs to be removed every six months and the pump oiled. The name plate
on the pump indicates the type of oil and the location for lubrication. Apply two or three
drops of oil into each location, essentially any type of S.A.E. 20 electric-motor oil can be
used.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12
CC-100 Coolant Circulator Manual
Version 1.B
Schematic Diagrams
Figure 1. Flow
diagram.
Figure 2.
115 V Chassis
Wiring
diagram.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Tips and Tricks
13
Figure 3.
100 V Chassis
Wiring
diagram.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
CC-100 Coolant Circulator Manual
Version 1.B
Figure 4.
230 V chassis
wiring.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Service
Warranty
This equipment is warranted to be free from defects of material and workmanship. It is
sold subject to the mutual agreement that the liability of Princeton Instruments, Inc., is
limited to replacing defective parts and/or repairing malfunctioning equipment at its
factory, provided the equipment is returned, transportation prepaid, within twelve (12)
months of its factory ship date.
The purchaser agrees that Princeton Instruments, Inc. shall assume no liability for
consequential damages resulting from its use or from packaging of shipments returned to
the factory.
Components which are damaged by misuse are not warranted. Units which have been
modified by a customer are not warranted.
UV coatings are not covered by this warranty.
Equipment Repairs
It is recommended that units requiring service in the United States be returned to the
factory located in Trenton, New Jersey. Before instrumentation is returned for service,
please consult a service engineer at the factory. In many cases, the problem may be
cleared up over the telephone.
If the unit needs to be returned, the service engineer will ask for a detailed explanation of
the problems encountered and a purchase order to cover any charges. You will then
receive a Returned Materials Authorization (RMA) number. Place this number on the
package so the returned equipment can be easily identified when received at the factory.
You must also include with the equipment a completed RMA form explaining the
symptoms or problems encountered. Without this document, repair turnaround time will
be considerably longer.
It is especially important to prevent freezing during shipping, because the temperature to
which the CC-100 will be exposed will not be under control. Since it is very difficult to
drain the CC-100 completely, it is strongly advised to fill with an antifreeze solution of
sufficient concentration to prevent freezing and allowed to circulate for at least five
minutes prior to draining in preparation for shipment. Before shipping the unit, the
plastic tube plugs should be installed on both the inlet and outlet tube fittings to prevent
leakage and possible additional damage.
If the unit is under warranty, the customer is only responsible for the transportation and
insurance charges to Princeton Instruments. Princeton Instruments is responsible for the
return transportation charges. If the unit is out of warranty, the customer is responsible
for all transportation charges (including insurance and duty fees, when applicable) as
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
CC-100 Coolant Circulator Manual
Version 1.B
well as all charges incurred to perform the repairs. In this case, the customer can decide
the insurance value.
International customers should contact your local manufacturers representative or
distributor for repair information.
Contact Information
Princeton Instrument’s manufacturing facility is located at the following address:
Princeton Instruments, Inc.
3660 Quakerbridge Road
Trenton, NJ 08619 (USA)
Tel: 609-587-9797
Fax: 609-587-1970
Tech Support E-mail: [email protected]
For technical support and service outside the United States, see our web page at
addresses of Princeton Instrument’s overseas offices and representatives is maintained
on the web page.
Download from Www.Somanuals.com. All Manuals Search And Download.
|