QUANTUM 614
SERIES
Including Models: Quantum 614, Quantum 614 3S,
Quantum 614 3SP, and Quantum 614 3MP
1-800-800-8586 (US) 1-888-570-1113 (Canada)
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T E N T S
I.
INTRODUCTION .................................................................................................................................. 4
II. SAFETY ................................................................................................................................................... 5
III. YOUR POWER CHAIR ..................................................................................................................... 18
IV. ASSEMBLY .......................................................................................................................................... 22
V. COMFORT ADJUSTMENTS ......................................................................................................... 24
VI. BATTERIES AND CHARGING .....................................................................................................29
VII. CARE AND MAINTENANCE ......................................................................................................... 33
VIII. WARRANTY ....................................................................................................................................... 39
APPENDIX I - SPECIFICATIONS ........................................................................................................ 41
Quantum 614 Series
3
Download from Www.Somanuals.com. All Manuals Search And Download.
I . I N T R O D U C T I O N
SAFETY
WELCOME to Quantum Rehab, a division of Pride Mobility Products Corporation (Pride). The power chair you
have purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident
that these design features will provide you with the conveniences you expect during your daily activities. Once
you understand how to safely operate and care for your power chair, it should give you years of trouble-free
operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair
for the first time. You must also read all instructions, warnings, and notes contained in any supplemental instruc-
tional booklets for the controller, front riggings, and/or seating system that accompanied your power chair before
initial operation. Your safety depends upon you, as well as your provider, caretaker, or healthcare professional in
using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for
setup or operation, please contact your Quantum Rehab Provider. Failure to follow the instructions in this
manual and those located on your power chair can lead to personal injury and/or damage to the power
chair, including voiding the warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or
remove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or
neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this
product.
SHIPPING AND DELIVERY
Before using your power chair, make sure your delivery is complete as some components may be individually
packaged. If you do not receive a complete delivery, please contact your Quantum Rehab Provider immediately.
Where damage has occurred during transport, either to the packaging or content, please contact the delivery com-
pany responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about
the safety and reliability of your new power chair, and about the service you received from your Quantum Rehab
Provider.
Please notify us of any change of address, so we can keep you apprised of important information about safety,
new products, and new options that can increase your ability to use and enjoy your power chair. Please feel free
to contact us at the address below:
USA:
Canada:
Pride Mobility Products Corporation
Attn.: Customer Care Department
182 Susquehanna Avenue
Exeter, PA 18643-2694
1-800-424-8205
Pride Mobility Products Company
380 Vansickle Road Unit 350
St. Catharines, Ontario L2R 6P7
1-888-570-1113
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.
4
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
PRODUCT SAFETY SYMBOLS
The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions.
It is very important for you to read and understand them completely.
Read and follow the information in the owner’s manual.
Do not allow unsupervised children to play near the power chair while the batteries are
charging.
Maximum seating weight.
Keep your hands away from the tires when driving. Be aware that loose fitting clothing
can become caught in drive tires.
Use correct tie-down points for controller harness to prevent the harness from getting
caught in the drive tires, pinched in the seat frame, or damaged when passing through
doorways.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain
and store in a clean and dry condition.
Quantum 614 Series
5
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Do not use a cell phone, walkie/talkie, laptop, or other radio transmitter while operating.
Removal of grounding prong can create electrical hazard. If necessary, properly install
an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
Do not connect an extension cord to the AC/DC converter or the battery charger.
Do not place power chair in freewheel mode on a decline.
Do not place power chair in freewheel mode on an incline.
Wear safety goggles.
Corrosive chemicals contained in battery.
6
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
EMI-RFI - This product has been tested and passed at an immunity level of 20 V/m.
Explosive conditions exist!
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions.
Keep tools and other metal objects away from battery terminals. Contact with tools can
cause electrical shock.
Battery Set Configuration:
+ = Positive (Red) Terminal Post
- = Negative (Black) Terminal Post
Connect Red wires to Red Positive (+) Terminal Posts
Connect Black wires to Black Negative (–) Terminal Posts
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and new
batteries. Always replace both batteries at the same time.
Quantum 614 Series
7
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Battery charger for indoor use only.
Disposal and recycling - Contact your Quantum Rehab Provider for information on proper
disposal and recycling of your Pride product and its packaging.
Locked and in drive mode.
Place unit on level ground and stand to one side when changing from drive
mode to freewheel mode or freewheel mode to drive mode.
Unlocked and in freewheel mode.
Contains Lead.
Do not adjust suspension.
Do not remove anti-tip wheels.
8
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Power chair information label
Quantum 614 Series
9
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
GENERAL GUIDELINES
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an
extensive variety of products to best fit the individual needs of the power chair user. Please be aware that the final
selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power
chair user, who is capable of making such a decision, and his/her healthcare professional (i.e., medical doctor,
physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the
power chair to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Pro-
vider in the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice
operating the power chair in the presence of a trained attendant. A trained attendant can be defined as a family
member or care professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you
will need some practice. Simply take your time and you will soon be in full and confident control as you maneuver
through doorways, on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help you become accustomed to oper-
ating your power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility. However, under
no circumstances should you modify, add, remove, or disable any feature, part, or function of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check
before each use to make sure your power chair operates smoothly and safely.
Perform the following inspections prior to using your power chair:
ꢀ Check for proper tire inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on each
tire if equipped with pneumatic tires.
ꢀ Check all electrical connections. Make sure they are tight and not corroded.
ꢀ Check all controller connections to the power base. Make sure they are secured properly.
ꢀ Check the brakes. See VII. “Care and Maintenance.”
ꢀ Check battery charge. See VI. “Batteries and Charging.”
NOTE: If you discover a problem, contact your Quantum Rehab Provider for assistance.
10
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
Keep in mind that the maximum weight capacity includes the combined weight of the user and any accessories
mounted to the power chair.
MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the
weight capacity voids your warranty. Pride will not be held responsible for injuries and/or
property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may affect the center of gravity, resulting in a tip or a fall.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly.
Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.
WARNING! It is important that the psi/bar/kPa air pressure rating indicated on each tire be
maintained in pneumatic tires at all times. Do not underinflate or overinflate your tires. Low pressure
may result in loss of control, and overinflated tires may burst. Failure to maintain the psi/bar/kPa air
pressure rating indicated on the pneumatic tires at all times may result in tire and/or wheel failure.
WARNING! Inflate your power chair drive tires from a regulated air source with an available
pressure gauge. Inflating your tires from an unregulated air source could overinflate them,
resulting in a burst tire.
NOTE: If the tire on your power chair lists the psi rating only, use the following conversion formulas to find
the bar or kPa rating: bar = psi x 0.06895; kPa = psi x 6.89476.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access.
Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on
your power chair.
ꢀ Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
ꢀ
Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s
rear wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
ꢀ When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure
a safely controlled descent.
ꢀ Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then
accelerate cautiously. When driving down an incline, set your power chair to the slowest speed setting and drive
in the forward direction only. If your power chair starts to move down the incline faster than you anticipated or
desired, allow it to come to a complete stop by releasing the joystick, then push the joystick forward slightly to
ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the power chair in
freewheel mode while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the
incline. Drive your power chair straight up the incline. This greatly reduces the possibility
of a tip or a fall. Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas
covered with snow, ice, cut grass, or wet leaves).
WARNING! Never travel down an incline backward. Doing so may cause the power chair
to tip. Always exercise extreme caution when negotiating an incline.
Quantum 614 Series
11
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
WARNING! If your power chair is equipped with a reclining seatback, do not attempt to
negotiate inclines with the seat in a reclined position. Do not attempt to negotiate obstacles
with the seat in a reclined position unless an attendant is present to help stabilize the chair.
Failure to heed may result in the power chair tipping over.
WARNING! Even though your power chair is capable of climbing slopes greater than those
illustrated in figure 1, do not, under any circumstances, exceed the incline guidelines or any other
specifications presented in this manual. Doing so could cause instability in your power chair.
Pride recommends that the maximum slope of an incline you attempt to safely ascend or descend on your power
chair does not exceed 6° (10.5%). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 6° (10.5%) may put your power
chair in an unstable position and cause it to tip.
6 (10.5%)
Figure 1. Maxim um Safe Slope (Ascending and Descending)
Freewheel Mode
Your power chair is equipped with two manual freewheel levers to allow for manual maneuverability by a trained
attendant. For more information about how to place your power chair into and out of freewheel mode, see III.
“Your Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present.
WARNING! Do not attempt to personally place your power chair in freewheel mode while
seated on it. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline or
decline. This could cause the chair to roll uncontrollably on its own.
Braking Information
Your power chair is equipped with two powerful brake systems:
ꢀ
Regenerative—uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
ꢀ Disc Park Brake—activates mechanically after regenerative braking slows the vehicle to near stop, or when
power is removed from the system for any reason.
Cornering Information
While your power chair is equipped with front and rear caster wheels, excessively high cornering speeds can still
create the possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to: cor-
nering speed, steering angle (how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from
an area of low traction to an area of high traction (such as passing from a grassy area to a paved area—especially at
high speed while turning), and abrupt directional changes. High cornering speeds are not recommended. If you feel
that you may tip over in a corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to
prevent your power chair from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable center of gravity.
This greatly reduces the possibility of a tip or fall.
12
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with
extreme caution.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces
composed of concrete, blacktop, or tarmac. However, Pride recognizes that there will be times when you will
encounter other surface types. For this reason, your power chair is designed to perform admirably on packed soil,
grass, and gravel. Feel free to use your power chair safely on lawns and in park areas.
ꢀ Avoid driving on uneven terrain and/or soft surfaces.
ꢀ Avoid tall grass that can entangle the running gear.
ꢀ Avoid loosely packed gravel and sand.
ꢀ Do not use your power chair in fresh or salt water.
ꢀ Do not use your power chair at the edge of a stream, lake, or ocean.
ꢀ If you feel unsure about a driving surface, avoid that surface.
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly
caught up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliest
opportunity. Thoroughly dry your power chair before storing, charging, or operating your power chair.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces
can have an adverse affect on the electrical system. Maintain and store your power chair in a
dry and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of
upholstered and non-upholstered items on the power chair, possibly resulting in skin irritation.
Exercise caution when using your power chair in extremely hot or cold conditions or when
exposing your power chair to direct sunlight for prolonged periods of time.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges, and/or drop-offs (curbs,
porches, stairs, etc.). Be sure your power chair is traveling perpendicular to any curb you are required to navigate.
See figure 2.
To navigate up over a curb or stationary obstacle:
1. Approach the curb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle.
See figure 2.
2. Increase the forward speed just before the front wheels come in contact with the obstacle.
3. Reduce the forward speed only after the rear wheels have cleared the obstacle.
To navigate down a curb or stationary obstacle:
1. Approach the curb or obstacle slowly, and make sure the power chair is traveling perpendicular to the obstacle.
See figure 2.
2. Reduce the forward speed just before the front wheels come in contact with the obstacle.
3. Increase the forward speed only after the rear wheels have cleared the obstacle and you are once again on a
level surface.
Quantum 614 Series
13
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Figure 2. Correct Curb Approach
Figure 3. Incorrect Curb Approach
WARNING! Even though your power chair may be capable of handling greater obstacles, Pride
recommends that you do not attempt to negotiate a curb that has a height greater than 2 in.
(5 cm). Doing so could cause instability in your power chair.
WARNING! Do not attempt to have your power chair proceed backward down any step, curb, or
other obstacle. This may cause the power chair to tip.
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators.
Doors
ꢀ Determine if the door opens toward or away from you.
ꢀ Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently
and slowly backward to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
ꢀ If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow
the rubber door edge to contact the power chair and the door will reopen.
ꢀ Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The
power chair should be stowed in the trunk of a car or in the back of a truck or van with the batteries removed and
properly secured. In addition, all removable power chair parts, including the armrests, seat, front riggings, con-
troller, and shrouds should be removed and/or properly secured during motor vehicle transport.
WARNING! Do not sit on your power chair while it is in a moving vehicle.
WARNING! Always be sure your power chair and its batteries are properly secured when it is
being transported. Batteries should be secured in an upright position and protective caps should
be installed on the battery terminals. Batteries should not be transported with any flammable or
combustible items.
14
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Positioning Belts
Your Quantum Rehab Provider, therapist(s), and other healthcare professionals are responsible for determining
your requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely in order to reduce the possibility of a fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should
be properly belted into seats approved by the vehicle manufacturer.
Lifts/Elevation Products
If you will be transporting your power chair during travel, you may find it necessary to use a vehicle-mounted lift
system or elevation product to aid in transportation. Pride recommends that you closely review the warnings,
instructions, specifications, and safety information set forth by the manufacturer of the lift/elevation product
before using that product.
WARNING! Not all lift systems/elevation products are rated for use with an occupied mobility
device. Pride recommends that you do not remain seated in your power chair when it is being
used in connection with any type of lift system/elevation product unless:
ꢀ
ꢀ
That product is rated for occupied use by the manufacturer.
You are able to occupy your mobility device in strict conformity with the warnings,
instructions, specifications, and safety guidelines set forth by the manufacturer.
WARNING! Always turn off the power to the controller when you are being transferred via an
elevation product. Failure to do so may result in accidental joystick contact, resulting in
unintended movement and personal injury or product damage.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts, including
the armrests, seat, front riggings, controller, and shrouds.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time,
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This
will also eliminate the possibility of unintended chair movement from electromagnetic (EM)
sources.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend
while seated on your power chair, it is important to maintain a stable center of gravity and keep the power chair
from tipping. Pride recommends that the power chair user determine his/her personal limitations and practice
bending and reaching in the presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the
floor by reaching down between your knees or if you have to reach over the back of the
seat. Movements such as these may change your center of gravity and the weight
distribution of the power chair. This may cause your power chair to tip.
WARNING! Keep your hands away from the tires when driving. Be aware that loose
fitting clothing can become caught in drive tires.
Quantum 614 Series
15
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Transfers
Transferring onto and off of your power chair
requires a good sense of balance. Always have an
attendant or healthcare professional present while
learning to properly transfer yourself.
To eliminate the possibility of injury, Pride recom-
mends that you or a trained attendant perform the fol-
lowing tasks before attempting a transfer:
ꢀ Turn off the power to the controller.
ꢀ Ensure your power chair is not in freewheel
mode. See III. “Your Power Chair.”
ꢀ
Turn the caster wheels toward the transfer destina-
tion to improve power chair stability during transfer.
ꢀ Make sure both armrests are flipped up or
removed from your power chair.
ꢀ Flip up the foot platform or move the leg rests
aside; this will help to keep your feet from getting
caught on the front rigging during the transfer.
ꢀ Reduce the distance between your power chair
and the object you are transferring onto.
Figure 4. Ideal Transfer Position
WARNING! Before transferring, position yourself as far back as possible in the power chair seat
to prevent the power chair from tipping forward during transfer.
WARNING! Avoid putting all of your weight on the power chair armrests and do not use the
armrests for weight bearing purposes, such as transfers. Such use may cause the power chair
to tip, resulting in a fall from the power chair.
WARNING! The controller and controller bracket are non-load bearing items in your power chair.
Do not use the controller or controller bracket for weight bearing purposes, such as transfers.
Such use may cause damage to these components, resulting in a fall from the power chair and
personal injury.
WARNING! Avoid putting all of your weight on the front riggings. Such use may cause the power
chair to tip.
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For
more information about your power chair’s batteries, see VI. “Batteries and Charging.”
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling and wash hands after handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable
to lift that much weight, be sure to get help. Use proper lifting techniques and avoid
lifting beyond your capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen
battery. Charging a frozen battery may result in damage to the battery.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables must be
connected to positive (+) battery terminals/posts. BLACK (-) cables must be connected
to negative (-) battery terminals/posts. Protective caps should be installed over all
battery terminals. REPLACE cables immediately if damaged.
16
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety
issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication
or if you have certain physical limitations. Some medications and limitations may impair your
ability to operate your power chair in a safe manner.
Alcohol/Smoking
The power chair user must exercise care and common sense when operating his/her power chair. This includes
awareness of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your
power chair, although the power chair has passed the necessary testing requirements for
cigarette smoking. You must adhere to the following safety guidelines if you decide to smoke
cigarettes while seated in your power chair.
ꢀ Do not leave lit cigarettes unattended.
ꢀ Keep ashtrays a safe distance from the seat cushions.
ꢀ Always make sure cigarettes are completely extinguished before disposal.
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-
way radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless com-
puter links, microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency
vehicles. In some cases, these waves can cause unintended movement or damage to the control system. Every
electrically-powered mobility vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the
greater the protection against EMI. This product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio
transmitters may cause unintended movement of your electrically-powered mobility vehicle
due to EMI. Exercise caution when using any of these items while operating your mobility
vehicle and avoid coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility
vehicle can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in
any way not authorized by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
tended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Contact your
Quantum Rehab Provider to report the incident.
Quantum 614 Series
17
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . Y O U R P O W E R C H A I R
THE QUANTUM 614 SERIES
Your power chair has two main assemblies: the seat assembly and the power base assembly. See figure 5. Typically,
the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/
brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses. See figures 5, 6, and 7.
SEATBACK
ARMREST
SEAT ASSEMBLY
JOYSTICK
CONTROLLER
SEAT BASE
SEATBACK RELEASE
LEVER
REAR
SHROUD
POWER BASE
ASSEMBLY
CASTER WHEEL
DRIVE WHEEL
FRONT RIGGING
CASTER WHEEL
(FOOT PLATFORM SHOWN)
Figure 5. The Quantum 614 Series Power Chair
18
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . Y O U R P O W E R C H A I R
TRAPEZE BARS
FRONT
COVER
Figure 6. The Quantum 614 Series Power Base
Electrical components
The electrical components are located on or inside the power base. The main circuit breaker is located on the front
of the power base. The power module is located inside the power base. See figure 7.
Motor Connectors: This is where the controller connects to the motors.
Battery Connector: This is where the controller connects to the batteries.
Controller Connector: This is where the controller connects to the power module or power base. Each controller
uses a different type of harness. Regardless of which type of controller is used, the harness must be secured to the
seat assembly and not allowed to drag on the floor.
Quantum 614 Series
19
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . Y O U R P O W E R C H A I R
Main Circuit Breaker: The main circuit breaker is a safety feature built into your power chair. When the batteries
and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage
to the motors and the electronics. If the circuit breaker trips, allow your power chair to “rest” for approximately
one minute. Next, push in the circuit breaker button, turn on the controller, and continue normal operation. If the
main circuit breaker continues to trip repeatedly, contact your Quantum Rehab Provider.
REAR SHROUD REMOVAL
FRONT SHROUD
CONTROLLER
CONNECTOR
POWER MODULE
BATTERY CONNECTOR
MAIN CIRCUIT
BREAKER
MOTOR CONNECTORS
Figure 7. Quantum 614 Series Electrical Com ponents
20
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . Y O U R P O W E R C H A I R
Manual Freewheel Levers
For your convenience, your power chair is equipped with two manual freewheel levers mounted on the motors.
These levers allow you to disengage the drive motors and maneuver the chair manually. You can manually push
the power chair by the seatback.
WARNING! Do not use the power chair while the drive motors are disengaged! Do not
disengage the drive motors when the power chair is on an incline, as the unit could roll
on its own! Only engage the freewheel mode when on a level surface.
WARNING! It is important to remember that when your power chair is in freewheel mode,
the braking system is disengaged.
To engage or disengage the drive motors:
1. Locate the lever on the front of each motor.
2. Push the two levers downward to disengage the drive motors (freewheel mode). See figure 8.
3. Pull the two levers upward to engage the drive motors (drive mode). See figure 9.
NOTE: If a lever is difficult to move in either direction, slightly rock the power chair back and forth. The lever
should then move to the desired position.
WARNING! Do not use the freewheel lever handles as tie-down points to secure this product.
Figure 8. Freewheel Mode (Drive Disengaged)
Figure 9. Drive Mode (Drive Engaged)
Quantum 614 Series
21
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . A S S E M B L Y
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation. It may also require
disassembly to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed
to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making
comfort adjustments.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert,
resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or
through your Quantum Rehab Provider.
ARMREST WIDTH ADJUSTMENT
SEAT INSTALLATION
ARMREST ANGLE
ADJUSTMENT
SEAT HEIGHT/ANGLE ADJUSTMENT
CONTROLLER POSITION
FOOT PLATFORM
ANGLE ADJUSTMENT
FOOT PLATFORM
HEIGHT/DEPTH
ADJUSTMENT
Figure 10. Quantum 614 Series Assem bly View (Standard Seating System Shown)
22
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . A S S E M B L Y
Seat Installation
It may be necessary to install the seat either prior to ini-
tial operation or after transporting your power chair.
Most seats are attached to the power base with the Uni-
versal Mounting System (UMS). The UMS consists of
universal parts that may be attached to any medium-
back or high-back seat, regardless of seat width or seat
depth. The two main components are aluminum extru-
sions mounted to the seat base. These extrusions attach
to a pair of trapeze bars that are mounted to the power
base. See figure 11.
REAR EXTRUSION
WARNING! Do not pick up the seat
frame by the armrests. They are free to
pivot, and you may lose control of the
seat if they do so.
To install the seat:
1. Tilt the seat back and slide the rear extrusion onto
the rear trapeze bar. See figure 11.
SETSCREW
2. Lower the front extrusion onto the front trapeze bar
until the seat locks into place.
3. Flip the seat latch safety down.
SEAT
LATCH
SAFETY
WARNING! Make sure the seat latch
safety is flipped down before using
your power chair.
4. Install the controller into one of the armrests.
Tighten the setscrew. See figure 11.
TRAPEZE BARS
5. Lift the armrest straight up, then route the controller
harness so that it cannot be pinched in the seat hinge
as shown in figure 11.
Figure 11. Universal Mounting System
NOTE: It is important that the armrest be lifted straight
up prior to securing the controller harness with wire
ties.
6. Plug the controller connector into the power base.
See figure 7.
7. Secure the controller harness to the armrest receiver
with one or more wire ties. See figure 12.
MANDATORY!
Prevent
controller
harness damage! Avoid routing the
controller harness on the outside of the
armrest pad. Route the harness under
the armrest or toward the inside of the
armrest pad. Use correct tie-down
points for the controller harness to
prevent the harness from getting
caught in the drive tires, pinched in the
seat frame, or damaged when passing
through doorways.
WIRE TIES
Figure 12. Controller Harness Routing
Quantum 614 Series
23
Download from Www.Somanuals.com. All Manuals Search And Download.
V . C O M F O R T A D J U S T M E N T S
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase
your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position.
NOTE: If your power chair is equipped with a Synergy Seat or TRU-Balance Power Positioning System, refer
to the seat adjustment information contained in separate manuals. If your power chair is equipped with a
contoured seating system, refer to the following information.
WARNING! The center of gravity of your power chair was factory set to a position that meets the
needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated your
power chair and made any necessary adjustments to suit your specific requirements. Do not
change your seating configuration without first contacting Pride Mobility Products or your
Quantum Rehab Provider.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to “Appendix I - Specifications” for specific component weights before you
disassemble the power chair.
WARNING! Remove the occupant from the power chair before making any adjustments.
You may need the following to make comfort
adjustments:
ꢀ metric/standard socket set and ratchet
ꢀ adjustable spanner
ꢀ thread lock
Seat Height and Seat Angle Adjustment
You can change the seat height to one of four positions
by raising the front and rear trapeze bars. If you raise
or lower only one trapeze bar (front or rear), you can
also change the seat base angle (dump).
Figure 13. Seat Height Adjustm ent - Seat Latch Safety
To change the seat height:
1. Turn off the power to the controller.
2. Disconnect the controller connector(s) from the
TRAPEZE BARS
SCREWS
power base. See figure 7.
3. Flip up the seat latch safety. See figure 13.
4. Squeeze the seat latch and release the seat from the
front trapeze bar.
RETAINING
CLIPS
SEAT POSTS
5. Slide the seat forward and remove it from the
power base.
6. Loosen the setscrews on the seat towers. See figure 14.
7. Loosen the screws that attach the trapeze bars to the
seat posts. See figure 14.
SEAT TOWERS
8. Remove the retaining clips that secure the seat
posts to the power base. See figure 14.
9. Move the trapeze bars up or down to the desired
height.
NOTE: Change the seat dump by raising or lowering
only one set of towers (front or back).
Figure 14. Seat Adjustm ent - Trapeze Bars
24
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V . C O M F O R T A D J U S T M E N T S
10. Reinstall the retaining clips from step 8.
11. Remove each screw from the trapeze bars and
apply thread lock.
12. Reinstall each screw into the trapeze bars and
tighten.
13. Tighten the setscrew in each seat tower. See figure 14.
14. Reinstall the seat.
15. Lift the armrest straight up, then route the control-
ler harness so that it cannot be pinched in the seat
hinge. See figure 11.
16. Reconnect the controller to the power base.
17. Secure the controller harness with one or more wire
ties. See figure 12.
Seat Position Adjustment
You can move the seat forward or rearward by chang-
ing the extrusion mounting position.
To change the seat position:
1. Unplug the controller connector(s) from the power
base.
2. Remove the seat from the power base.
3. Remove both extrusions from the bottom of the
seat.
Figure 15. Seat Position Adjustm ent
4. Reposition the extrusions on a different set of
mounting holes. You must move both extrusions
the same number of holes either forward or back-
wards. See figure 15.
5. Fasten the extrusions back onto the bottom of the
seat.
6. Reinstall the seat.
7. Lift the armrest straight up, then route the control-
ler harness so that it can not be pinched in the seat
hinge. See figure 11.
8. Reconnect the controller.
9. Secure the controller harness with one or more wire
ties. See figure 12.
Manual Recline Seatback Adjustment
If your power chair is equipped with a reclining seat,
you can adjust the seatback angle with the seatback
release lever. The lever is located on the right side of
the seat base. See figure 5.
To adjust the recline angle:
1. Pull up on the seatback release lever.
2. Lean forward or backwards to the desired position.
3. Release the lever.
Quantum 614 Series
25
Download from Www.Somanuals.com. All Manuals Search And Download.
V . C O M F O R T A D J U S T M E N T S
Seatback Angle Adjustment
If your power chair is equipped with an adjustable seat-
back, you can adjust it to four (4) different angles: 90°,
102°, 105°, or 107°.
JAM NUT
ARMREST ANGLE
ADJUSTING SCREW
To adjust the seatback angle:
1. Remove the adjusting screws from each seat hinge.
See figure 16.
2. Set the seatback at the desired angle.
3. Reinstall the adjusting screws to each seat hinge
and tighten.
ARMREST
HEIGHT
ADJUSTING
SETSCREWS
Armrest Width Adjustment
You can change each armrest’s width independently of
the other.
SEATBACK ANGLE
ADJUSTING SCREW
NOTE: Changing the armrest width may increase the
overall width of your power chair.
ARMREST
KNOB
To change the armrest width:
1. Locate the two armrest knobs on each side of the
armrest receiver bracket. See figure 16.
2. Loosen the knobs.
Figure 16. Seatback/Arm rest Adjustm ent
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicu-
lar to the floor. See figure 16.
2. Loosen the jam nut.
3. Turn the adjusting screw to raise or lower the front
of the armrest.
4. Tighten the jam nut to lock the adjusting screw into
place.
Armrest Height Adjustment
To change the armrest height:
1. Loosen the two setscrews located on the armrest
receiver. See figure 16.
2. Raise or lower the armrest to the desired height.
3. Tighten the setscrews to secure the armrest.
26
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V . C O M F O R T A D J U S T M E N T S
Controller Position
You can move the controller in toward or out away from
the armrest, or change the position of the controller for
either left-hand or right-hand use.
WARNING! Do not place the controller
harness so that it can be pinched in the
seat frame or the power base frame.
CONTROLLER
BRACKET
To extend the controller:
SETSCREW
1. Flip up the armrest so it is perpendicular to the floor.
2. Loosen the setscrew on the controller bracket. See
figure 17.
3. Slide the controller into or out of the armrest to the
desired position.
4. Tighten the setscrew to secure the controller.
To change the controller position:
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the power
base.
3. Cut the wire tie(s) securing the controller harness to
the armrest.
4. Flip up the armrest and loosen the setscrew. See fig-
ure 17.
Figure 17. Underside of Arm rest
5. Slide the controller out of the armrest.
6. Loosen the setscrew in the other armrest.
7. Place the controller in the other armrest.
8. Tighten the setscrew in each armrest.
9. Use a wire tie to secure the controller harness to the
armrest.
SECUREMENT NUT
10. Plug the controller connector(s) into the power base.
NOTE: If your power chair is equipped with a Synergy
Seat or TRU-Balance Power Positioning System, refer
to the controller adjustment information contained in
separate manuals.
FOOT
PLATFORM
BRACKET
Foot Platform Height Adjustment
The foot platform height is easily adjusted to several dif-
ferent heights.
To raise or lower the foot platform:
1. Remove the hardware from the foot platform bracket.
See figure 18.
Figure 18. Foot Platform Adjustm ent
2. Loosen the foot platform securement nut one-half
turn.
3. Raise or lower the foot platform to the desired height.
4. Reinstall the hardware into the foot platform bracket
and tighten.
5. Tighten the securement nut.
Quantum 614 Series
27
Download from Www.Somanuals.com. All Manuals Search And Download.
V . C O M F O R T A D J U S T M E N T S
Foot Platform Depth Adjustment
To adjust the foot platform depth:
1. Remove the hardware from the foot platform
bracket. See figure 18.
2. Move the foot platform in or out to the desired
depth.
3. Reinstall the hardware into the foot platform
bracket and tighten.
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform with a
hex key. See figure 19.
ADJUSTMENT SCREW
To adjust the foot platform angle:
1. Flip up the foot platform and locate the adjustment
screw.
2. Turn the adjustment screw to raise or lower the
front of the foot platform.
Figure 19. Underside of Foot Platform
28
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . B A T T E R I E S A N D C H A R G I N G
BATTERIES AND CHARGING
Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance
free. Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed
to handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are
not interchangeable. Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe
for use in power chairs.
MANDATORY! Battery posts, terminals, and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash hands
after handling.
PROHIBITED! Always use two batteries of the exact same type, chemistry, and amp-
hour (Ah) capacity. Refer to the specifications table in this manual and in the manual
supplied with the battery charger for recommended type and capacities.
WARNING! Contact your Quantum Rehab Provider if you have any questions regarding
the batteries in your power chair.
Charging the Batteries
The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize
your power chair’s performance by charging the batteries safely, quickly, and easily. The battery charger is only
functional when the charger power cord is plugged into an electrical outlet.
PROHIBITED! Removal of grounding prong can create electrical hazard. If
necessary, properly install an approved 3-pronged adapter to an electrical outlet
having 2-pronged plug access.
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the
charger directly into a properly wired standard electrical outlet.
PROHIBITED! Do not allow unsupervised children to play near the power chair while
the batteries are charging. Pride recommends that you do not charge the batteries
while the power chair is occupied.
MANDATORY! Read the battery charging instructions in this manual and in the
manual supplied with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries. Keep the
power chair and battery charger away from sources of ignition such as flames or
sparks and provide adequate ventilation when charging the batteries.
WARNING! You must recharge your power chair’s batteries with the supplied off-
board battery charger. Do not use an automotive-type battery charger.
WARNING! Inspect the battery charger, wiring, and connectors for damage before
each use. Contact your Quantum Rehab Provider if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger
does not appear to be working correctly, contact your Quantum Rehab Provider.
WARNING! If the battery charger is equipped with cooling slots, then do not attempt
to insert objects through these slots.
WARNING! If your battery charger has not been tested and approved for outdoor use,
then do not expose it to adverse or extreme weather conditions. If the battery
charger is exposed to adverse or extreme weather conditions, then it must be
allowed to adjust to the difference in environmental conditions before use indoors.
Refer to the manual supplied with the battery charger for more information.
Quantum 614 Series
29
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . B A T T E R I E S A N D C H A R G I N G
To charge the batteries using the off-board charger:
1. Position the front of your power chair next to a
standard electrical outlet.
2. Be certain the controller power is turned off.
3. Plug the off-board charger into the off-board char-
ger/programming socket on the controller. See
figure 20.
4. Plug the off-board charger into the electrical outlet.
NOTE: The LED lights on the charger indicate dif-
ferent charger conditions at various times: charger
power on, charging in progress, and charging com-
plete. Refer to the manual supplied with the charger
for a complete explanation of these indicators.
5. When the batteries are fully charged, unplug the
off-board charger from the electrical outlet and
then from the controller.
Figure 20. Battery Charging
Battery Break-in
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak
performance level.
2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until
you become accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will
now perform at over 90% of their potential.
4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it
to 24 VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery
voltage is low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the
charger does not work as hard to complete the charging cycle. When the battery is fully charged, the amperage
from the charger is nearly at zero. This is how the charger maintains a charge but does not overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries.
We do not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero
voltage. If this happens, call your Quantum Rehab Provider for assistance.
30
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . B A T T E R I E S A N D C H A R G I N G
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries. You may use your power chair all
day on a daily basis or you may not use it for weeks at a time.
ꢀ Daily Use
If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power
chair. Your power chair will be ready each morning to give you a full day’s service. It is recommended that
you charge the batteries 8 to 14 hours after daily use.
ꢀ Infrequent Use
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once
per week for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the
batteries for more than 24 hours at a charging cycle.
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves.
More often you are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind.
All of these factors will affect the distance or running time per battery charge. Below are a few suggestions for
obtaining the maximum range per charge:
ꢀ Always charge the batteries fully prior to your trip.
ꢀ Plan your trip in advance to avoid inclines if possible.
ꢀ Limit baggage weight to essential items.
ꢀ Try to maintain an even speed and avoid stop-and-go driving.
What type of batteries should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-
cycle batteries that are similar in performance.
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell
batteries to reduce the risk of leakage or explosive conditions.
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cad-
mium (nicads), or in other common battery types. Deep-cycle batteries are specifically designed to provide
power, drain down their charge, and then accept a relatively quick recharge. AGM and Gel-Cell batteries should
be charged as often as possible. They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific
demands. Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping,
the batteries encounter temperature extremes that may influence initial performance. Heat robs the charge from
the battery, and cold slows the power available and extends the time needed to recharge the battery (just as with
a car battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature.
More importantly, it will take a few “charging cycles” (a partial drain—then a full recharge) to establish the
critical chemical balance that is essential to the battery’s peak performance and long life. It will be well worth it
to take the time to break in your battery properly.
NOTE: The useful life of a battery is quite often a reflection of the care it receives.
Quantum 614 Series
31
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . B A T T E R I E S A N D C H A R G I N G
How can I ensure maximum battery life?
A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power
chair’s batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently
charged, or stored without a full charge may be permanently damaged, causing unreliable power chair operation
and limited battery life.
How should I store my power chair and its batteries?
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries
at least once per week.
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage.
Disconnect the battery harnesses and store the power chair in a warm, dry environment. Avoid temperature
extremes, such as freezing and excessively hot conditions, and never attempt to charge a frozen battery. A cold or
frozen battery should be warmed for several days prior to recharging.
What about public transportation?
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These
batteries are Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, and
trains, as there is no danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance
to determine that carrier’s specific requirements.
What about shipping?
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair
in the original shipping container and ship the batteries in separate boxes.
32
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . C A R E A N D M A I N T E N A N C E
CARE AND MAINTENANCE
Your Quantum 614 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance
checks. You can perform some of these checks, but others require assistance from your Quantum Rehab Provider.
Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you
can help ensure that your power chair gives you years of trouble-free operation. If you have any doubt as to your
power chair’s care or operation, contact your Quantum Rehab Provider.
WARNING! Do not service the power chair when the seat is occupied.
Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areas
of any kind.
WARNING! Direct or prolonged exposure to water or dampness could cause the power
chair to malfunction electronically and mechanically. Water can cause electrical
components to corrode and the chair's frame to rust. Power chairs should be examined
periodically for signs of corrosion caused by water exposure, bodily fluid exposure, or
incontinence. Damaged components should be replaced or treated immediately.
Should your power chair come in contact with water:
1. Dry your power chair as thoroughly as possible with a towel.
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your power chair again.
4. If any inconsistencies are found, take your power chair to a Quantum Rehab Provider. Power chairs that are
frequently exposed to sources of water, such as incontinence, should be inspected often for corrosion and
electronic components may need to be replaced frequently.
Temperature
ꢀ Some of the parts of your power chair are susceptible to extreme changes in temperature. Always keep your
power chair between the temperatures of 18°F (-8°C) and 122°F (50°C).
ꢀ In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze
depends on a number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM
or Gel-Cell).
ꢀ Temperatures above 122°F (50°C) may cause your power chair to operate at a reduced speed. This reduced
speed is a safety feature built into the controller that helps prevent damage to the motor and other electrical
components.
General Guidelines
ꢀ Avoid knocking or bumping the controller, especially the joystick.
ꢀ Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.
ꢀ Keep the controller clean.
ꢀ Check all connectors to ensure that they are all tight and secured properly.
ꢀ Make sure pneumatic drive tires are inflated to the psi/bar/kPa air pressure rating indicated on each tire.
WARNING! Make sure pneumatic tires are inflated to the psi/bar/kPa air pressure rating
indicated on each tire. Do not underinflate or overinflate your tires. Low pressure may result in
loss of control, and overinflated tires may burst. Overinflating tires can cause them to explode.
WARNING! Do not use a high pressure hose to inflate your tires.
ꢀ Use a rubber conditioner on the tire sidewalls to help preserve them.
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the
tires slippery and cause your power chair to skid.
Quantum 614 Series
33
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . C A R E A N D M A I N T E N A N C E
ꢀ All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
ꢀ The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help
it retain its high-gloss appearance.
ꢀ Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within
the battery tray, with the battery terminals facing inward, toward each other. Refer to the battery wiring label
for the correct wiring layout.
WARNING! Even though the power chair has passed the necessary testing
requirements for ingress of liquids, you should keep electrical connections away from
sources of dampness, including direct exposure to water or bodily fluids and
incontinence. Check electrical components frequently for signs of corrosion and
replace as necessary.
Daily Checks
ꢀ With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the
neutral position when you release it. Check the rubber boot around the base of the joystick for damage. Visually
inspect the boot. Do not handle or try to repair it. See your Quantum Rehab Provider if there is a problem.
ꢀ Visually inspect the controller harness. Make sure that it is not frayed, cut, or has any wires exposed. See your
Quantum Rehab Provider if there is a problem.
ꢀ Check for flat spots on solid tires. Flat spots could adversely affect stability.
ꢀ Inspect the armrests for loose hardware, stress points, or damage. See your Quantum Rehab Provider if there
is a problem.
Weekly Checks
ꢀ Disconnect and inspect the controller from the power base. Look for corrosion. Contact your Quantum Rehab
Provider if necessary.
ꢀ
Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.
ꢀ Check for proper tire inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on each
tire. If a tire does not hold air, see a Quantum Rehab Provider for replacement of the tube.
ꢀ Check the brakes. This test should be carried out on a level surface with at least 3 feet (1 meter) of clearance
around your power chair.
To check the brakes:
1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick. You
must be able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this
test three times, pushing the joystick backwards, then left, and then right.
Monthly Checks
ꢀ Check for drive tire wear. See your Quantum Rehab Provider for repair.
ꢀ Check the caster wheels for wear. Replace them as necessary.
ꢀ Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the
bearings replaced. See your Quantum Rehab Provider for repair.
ꢀ Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
Yearly Checks
Take your power chair to your Quantum Rehab Provider for yearly maintenance, especially if you use your power
chair on a daily basis. This helps ensure that your power chair is functioning properly and helps prevent future
complications.
34
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . C A R E A N D M A I N T E N A N C E
Storage
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the
batteries from the power chair. See VI. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored
without a full charge may be permanently damaged, causing unreliable performance and limited service life. It is
recommended that you charge the batteries periodically throughout periods of prolonged storage to ensure proper
performance.
You may wish to place several boards under the frame of your power chair to raise it off of the ground during
periods of prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing
on the areas of the tires contacting the ground.
Disposal of Your Power Chair
Your power chair must be disposed of according to applicable local and national statutory regulations. Contact
your local waste disposal agency or Quantum Rehab Provider for information on proper disposal of power chair
packaging, metal frame components, plastic components, electronics, batteries, neoprene, silicone, and polyure-
thane materials.
Cleaning and Disinfection
ꢀ Use a damp cloth and mild, non abrasive cleanser to clean the plastic and metal parts of your power chair.
Avoid using products that may scratch the surface of your power chair.
ꢀ If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on
your product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning
agent before applying it to your product. Failure to comply may result in skin irritation or
premature deterioration of upholstery and/or power chair finishes.
WARNING! Never hose off your power chair or place it in direct contact with water. Your power
chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp
cloth.
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
Wheel Replacement
If you have pneumatic tires and you have a flat tire, you can replace the tube. If your chair is equipped with a solid
tire insert, then you must replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are
readily available through your Quantum Rehab Provider.
WARNING! The wheels on your power chair should only be serviced or replaced by a Quantum
Rehab Provider or a qualified technician.
WARNING! Be sure that the controller’s power is turned off and the power chair is not in
freewheel mode before performing this procedure.
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the
wheel. If any further disassembly is required, deflate the tire completely or it may explode.
Quantum 614 Series
35
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . C A R E A N D M A I N T E N A N C E
AXLE KEY
TIRE
TUBE
AXLE SLOT
SCREWS
REAR RIM HALF
FRONT RIM HALF
DRIVE WHEEL WASHER
DRIVE WHEEL NUT
Figure 21. Quantum 614 Series Drive W heel
Figure 22. Quantum 614 Series Drive W heel Disassem bled
Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:
1. Turn off the power to the controller.
2. Set the power chair up on blocks.
3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the axle. See figure 21.
5. Pull the wheel off the axle.
6. Remove the screws from the rim assembly and separate the front and rear rim. See figure 22.
7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if
it is a solid tire.
8. Reassemble the rims and reinstall the screws.
9. Slide the wheel back onto the axle. Make sure that the key is in the axle slot.
WARNING! Failure to ensure that the axle key is properly installed into the axle slot when
mounting the wheel can result in electronic brake failure, personal injury, and/or product damage.
10. Reinstall the drive wheel nut and washer onto the axle and tighten.
WARNING! Make sure both the nut and washer are reinstalled and tightened properly.
11. Inflate pneumatic tires to the psi/bar/kPa air pressure rating indicated on each tire.
12. Remove the power chair from the blocks.
Battery Replacement
A battery wiring diagram is printed on a decal located on the front battery tray. See figure 23. See VI. “Batteries
and Charging” for correct battery specifications.
MANDATORY! Battery posts, terminals, and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash hands
after handling.
WARNING! The batteries in your power chair should only be serviced or replaced by
a Quantum Rehab Provider or a qualified technician.
WARNING! Do not replace battery when seat is occupied.
WARNING! Power chair batteries are heavy. See specifications table. If you are
unable to lift that much weight, be sure to get help. Use proper lifting techniques and
avoid lifting beyond your capacity.
WARNING! Do not mix old and new batteries. Always replace both batteries at the
same time.
36
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . C A R E A N D M A I N T E N A N C E
REAR SHROUD
BATTERY WIRING DIAGRAM
BATTERY
STRAP
PULL POINTS FOR
REAR SHROUD
REMOVAL
DISCONNECT
RELEASE BUTTON
REAR BATTERY
FRONT BATTERY
Figure 23. Battery Rem oval/Installation
Quantum 614 Series
37
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . C A R E A N D M A I N T E N A N C E
To replace the batteries:
1. Turn off the power to the controller.
2. Make sure that the power chair is in drive mode. See III. “Your Power Chair.”
3. Pull to remove the rear shroud. See figure 23.
4. Push down on the disconnect release button and disconnect the rear battery harness from the power base. See
figure 23.
5. Unfasten the battery strap from around the rear battery.
6. Slide the rear battery out.
7. Push down on the disconnect release button and disconnect the front battery harness from the power base. See
figure 23.
8. Remove the front battery.
9. Remove the battery harness from each battery.
10. Install a battery harness onto each new battery according to the battery wiring diagram. See figure 23. Make
sure that you connect the red wire to the positive (+) battery terminal and the black wire to the negative (-)
battery terminal for each battery.
WARNING! Make sure you tighten the fasteners so that the connections are secure.
11. Place the batteries back into the power base.
12. Fasten the battery strap around the rear battery.
13. Connect each battery harness to its mating plug on the power base.
14. Reinstall the rear shroud.
15. Charge the batteries. See VI. “Batteries and Charging.”
When to See Your Quantum Rehab Provider for Service
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your
Quantum Rehab Provider. When calling, have the model number, serial number, nature of the problem, and the
error code if available.
ꢀ Motor noise
ꢀ Frayed harnesses
ꢀ Cracked or broken connectors
ꢀ Uneven wear on any of the tires
ꢀ Jerky motion
ꢀ Pulling to one side
ꢀ Bent or broken wheel assemblies
ꢀ Does not power up
ꢀ Powers up, but does not move
Corrective Maintenance
If the battery condition meter does not light up when you turn on the power:
ꢀ Check the harness connections. Make sure they are tight.
ꢀ Check the circuit breaker. Reset it if necessary.
ꢀ Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are
available at automotive parts stores. Disconnect both batteries before load testing and follow the directions that
come with the load tester. If either one of the batteries fails the load test, replace both of them. If your power chair
still does not power up, contact your Quantum Rehab Provider.
38
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . W A R R A N T Y
LIFETIME LIMITED WARRANTY
For the lifetime of your power chair from the date of purchase, Pride will repair or replace at our option to the
original purchaser, free of charge, any of the following parts found upon examination by an authorized represen-
tative of Pride to be defective in material and/or workmanship:
Structural frame components, including:
ꢀ Main frame
ꢀ Fixed-position seat post
TWO-YEAR LIMITED WARRANTY
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser,
free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
Electronic components, including:
ꢀ Charger assembly ꢀ Controller ꢀ Joystick
Main frame assemblies, including:
ꢀ Anti-tip forks ꢀ Caster beam ꢀ Metal seat framing ꢀ Caster forks
Other components, including:
ꢀ Front riggings ꢀ Electrical harness ꢀ Front rigging mounting brackets
18-MONTH LIMITED WARRANTY
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of
Pride to be defective in material and/or workmanship:
ꢀ Motor/gearbox assembly
ꢀ Power seat actuator
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
ꢀ Accessories
ꢀ Brakes (electronic function ONLY)
SIX-MONTH LIMITED WARRANTY
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser,
free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
ꢀ Bearings and bushings
ꢀ Plastic components, except body
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are
not warranted by Pride.
Quantum 614 Series
39
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . W A R R A N T Y
RECONDITIONED UNITS WARRANTY
All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase.
WARRANTY EXCLUSIONS
This warranty does not extend to those items which may require replacement due to normal wear and tear.
ꢀ ABS Plastic shrouds ꢀ Motor brushes
ꢀ Upholstery and seating
ꢀ Brake Pads
ꢀ Tires and tubes ꢀ Fuses/Bulbs
ꢀ Circumstances beyond the control of Pride
ꢀ Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically autho-
rized by Pride Mobility Products Corporation
ꢀ Repairs and/or modifications made to any part without specific consent from Pride
Exclusions also include components with damage caused by:
ꢀ Contamination
ꢀ Abuse, misuse, accident, or negligence
ꢀ Battery fluid spillage or leakage
ꢀ Commercial use, or use other than normal
ꢀ Improper operation, maintenance, or storage
NOTE: Gradual deterioration in performance because the battery has been left in a discharged state, left in
cold conditions for an extended period of time, or worn out through heavy use is not covered.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service must be performed by a Quantum Rehab Provider. Do not return faulty parts to Pride without
prior written authorization. All transportation costs and shipping damage incurred while submitting parts for
repair or replacement are the responsibility of the purchaser.
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride
product can result in personal injury or product damage and will void Pride’s product warranty.
There is no other express warranty.
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1)
year from the date of purchase and to the extent permitted by law. Any and all implied warranties are excluded.
This is the exclusive remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some counties do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of
limitation incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from county to county.
Please fill out and return the product registration card to Pride. This will aid Pride in providing the best possible
technical and customer service.
40
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P E N D I X I - S P E C I F I C A T I O N S
SPECIFICATIONS
Suspension
ATX Suspension (Active-Trac with extra stability)
14 in. (35.56 cm), pneumatic or solid available
Drive Wheels
Caster Wheels
6 in. (15.24 cm), solid (front and rear)
Up to 5 mph (8 km/h)
1
Maximum Speed
Brakes
“Intelligent Braking” electronic regenerative, disc park brake
2
See figure 24.
See figure 24.
Ground Clearance
2
Turning Radius
Length: See figure 24.
Width: See figure 24.
2
Overall Size
Drivetrain
Two motor, mid-wheel drive
3
Two 12-volt, deep-cycle NF-22 batteries
Batteries
1,4
Range
Variable up to 13 miles (20.92 km)
5-amp, off-board (standard)
8-amp, off-board (optional)
Battery Charger
Weight Capacity
300 lbs. (136 kg)
Base: 121.5 lbs. (55.11 kg)
Batteries: 38 lbs. (17.23 kg) each
2
Component Weights
1
2
Varies with base model, user weight, terrain type, battery amp hour rating (Ah), battery charge, battery condition, motors, controller
type, tire type, and tire condition. This specification can be subject to a variance of (+ or -) 10%.
Due to manufacturing tolerances and continued product improvement, this specification can be subject to a variance of (+ or – ) 3%.
AGM or Gel-Cell type required. See VI. “Batteries and Charging.”
Tested in accordance with ASNI/RESNA, WC Vol 2, Section 4 and ISO 7176-4 standards. Results derived from theoretical calcu-
3
4
lation based on battery specifications and drive system performance. Test conducted at maximum weight capacity.
NOTE: The product conforms to all applicable ANSI-RESNA testing requirements and ISO 7176 series EN12184
standards. All specifications subject to change without notice.
Quantum 614 Series
41
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P E N D I X I - S P E C I F I C A T I O N S
LENGTH
40.0” (101.6 cm)
35.5” (90.17 cm)
WIDTH
25.125” (63.82 cm)
20.0” (50.8 cm)
2.25” (5.72 cm)
1.625” (4.12 cm)
AT FOOT PLATFORM
GROUND CLEARANCE
TURNING RADIUS
Figure 24. Quantum 614 Series Dim ensions and Ground Clearance
42
Quantum 614 Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quality Control - Quantum 614 Series
Inclusion of all Parts
Joystick Serial Number
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
Fit and Finish
Performance
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
*I NFMANU3735*
Product Serial #
Download from Www.Somanuals.com. All Manuals Search And Download.
|