Owner’s Manual
ATTENTION:
Please read the content
of your owner’s manual
before operating your
power chair.
Exeter, PA
St. Catharines, ON
1-800-800-8586
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T E N T S
I.
INTRODUCTION......................................................................................................................... 4
II. SAFETY ......................................................................................................................................... 6
III. EMI/RFI ........................................................................................................................................ 14
IV. THE JAZZY 1122 ................................................................................................................... 16
V. ASSEMBLY................................................................................................................................. 22
VI. COMFORT ADJUSTMENTS................................................................................................ 24
VII. DISASSEMBLY ......................................................................................................................... 30
VIII. OPERATION............................................................................................................................... 31
IX. BATTERIES AND CHARGING ............................................................................................ 43
X. CARE AND MAINTENANCE ................................................................................................ 48
XI. OPTIONAL ACCESSORIES................................................................................................. 52
XII. WARRANTY................................................................................................................................ 54
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
3
Download from Www.Somanuals.com. All Manuals Search And Download.
I . I N T R O D U C T I O N
Welcome to Pride Mobility Products Corporation (Pride). Congratulations on the purchase of your new Pride
Power Chair. The Pride Power Chair design combines the most advanced state-of-the-art components with
modern, attractive styling. We are certain that the design features and trouble-free operation of your new power
chair will add convenience to your daily living.
At Pride, your safety is important to us. Please read and follow all of the instructions in this manual before you
attempt to operate your Jazzy for the first time. These instructions were produced for your benefit. Your under-
standing of these instructions is essential for the safe operation of your new power chair.
Pride is not liable for damage to property or personal injury arising out of unsafe use of a power chair. Pride is also
not liable for any property damage or personal injury arising out of the failure of any person and/or user to following
the instructions and recommendations set forth in this manual or any other instructions or recommendations con-
tained in other power chair related literature issued by Pride or contained on the power chair itself.
This owner’s manual is compiled from the latest specifications and product information available at the time of
publication. We reserve the right to make changes as they become necessary. Any changes to our products may
cause slight variations between the illustrations and explanations in this manual and the product you had purchased.
If you experience any problems with your power chair that your are unable tosolve, or if you do not feel capable of
safely following any of the instructions and/or recommendations as contained in this manual, please contact your
authorized Pride provider for assistance.
Once you understand how to operate and take care of your power chair, we are certain that it will give you years of
trouble-freeserviceandenjoyment.
Information Exchange
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the
safetyandreliabilityofyournewpower chair,and abouttheserviceyoureceivedfromyour authorizedPrideprovider.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your power chair.Please feel free to write us
at the address below:
Pride Mobility Products Corporation
Attn: Customer Care Department
182 SusquehannaAvenue
Exeter, PA18643-2694
1-800-424-8205
4
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I . I N T R O D U C T I O N
Pride Owners Club
As an owner of a Pride product, you are invited to register your product’s warranty and enroll in the Pride Owners
Club. You may do so by filling out and returning your enclosed registration card or by visiting Pride’s web site at
www.pridemobility.com. As a registered member, each time you visit our site, you will have access to the most
interactive and honest educational venue available today for people with mobility needs, their families and friends.
From our home page, click on the button that reads “Owners Club” to enter a page dedicated to current and
potential Pride product owners. You will gain access to interviews, stories, recreation ideas, daily living tips,
product and funding information, and interactive message boards. On these message boards you are invited to
speak with other Pride customers as well as Pride representatives who are available to assist you with any ques-
tions or concerns you may have.
My Authorized Pride Provider is:
Name:_______________________________________________________________________________
Address:_____________________________________________________________________________
Phone Number:________________________________________________________________________
Quick Reference Information:
Purchase Date:________________________________________________________________________
NOTE:If you ever lose or misplace your product registration card or your copy of this manual, call or write
to us and we will be glad to send you a new one immediately.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
5
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
SAFETY
WARNING! Do not operate your new power chair for the first time without completely
reading and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an
extensive variety of products to best fit the individual needs of the power chair user. Please be aware that the final
selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power
chair user, who is capable of making such a decision, and his/her healthcare professional (i.e., medical doctor,
physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power
chair to the user and has assisted the prescribing healthcare professional and/or the authorized Pride provider in the
instruction process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice
operating the power chair in the presence of a trained attendant.Atrained attendant can be defined as a family
member or care professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you will
need some practice. Simply take your time and you will soon be in full and confident control as you maneuver
through doorways, on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help the user become accustomed to
operating the power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and electronics.Awide range
of accessories is available from your authorized Pride provider to further customize your power chair to better suit
your needs and/or preferences. However, under no circumstances should you modify, add, remove, or disable any
feature, part, or function of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Unautho-
rized modifications may result in personal injury and/or damage to your power chair.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check
before each use to make sure your power chair operates smoothly and safely. See X. “Care and Maintenance.”
Perform the following inspections prior to using your power chair:
n Check for proper tire inflation. Maintain 30-35 psi in each tire (if equipped with pneumatic tires).
n Check all electrical connections. Make sure they are tight and not corroded.
n Check all controller connections to the electronics tray. Make sure they are secured properly.
6
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
n Check the brakes. See X. “Care and Maintenance.”
n Check battery charge. See IX. “Batteries and Charging.”
NOTE: If you discover a problem, contact your authorized Pride provider for assistance.
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
WARNING! Exceeding the weight capacity voids your warranty and may result in personal
injury and/or damage to your power chair. Pride will not be held responsible for injuries
and/or property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your
power chair may result in personal injury and/or property damage.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked at least
once a week. Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of
your power chair.
WARNING! It is important that 30-35 psi tire pressure be maintained in pneumatic tires at
all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of
control, and overinflated tires may burst. Failure to maintain 30-35 psi tire pressure in
pneumatic tires at all times may result in tire and/or wheel failure, causing serious per-
sonal injury and/or damage to your Jazzy.
WARNING! Inflate your power chair drive tires from a regulated air source with an avail-
able pressure gauge. Inflating your tires from an unregulated air source could overinflate
them, resulting in a burst tire and/or personal injury.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access.
Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on
your power chair.
n Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
n Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power
chair’s rear wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any
railing corners.
n When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to
ensure a safely controlled descent. See VIII. “Operation.”
n Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then
accelerate cautiously. When driving down an incline, set your power chair to the slowest setting and drive in the
forward direction only. If your power chair starts to move down the incline faster than you anticipated or desired,
allow it to come to a complete stop by releasing the joystick, then push the joystick forward slightly to ensure a
safely controlled descent.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
7
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the
incline. Drive your power chair straight up the incline. This greatly reduces the possibility
of a tip or a fall. Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas
covered with snow, ice, cut grass, or wet leaves).
WARNING! When on any sort of an incline or decline, never place the power chair in
freewheel mode while seated on it or standing next to it. Doing so may result in personal
injury and/or damage to your power chair.
WARNING! Never travel down an incline backwards. This may result in personal injury.
In compliance with theAmericans with DisabilitiesAct of 1990, all handicap public access ramps are required to
have a maximum slope of 5°. Therefore, Pride recommends that the maximum slope of an incline you attempt to
safely ascend or descend on your power chair does not exceed 5°. See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 5° may put your power
chair in an unstable position and cause it to tip, resulting in personal injury.
Figure 1. Maximum Safe Angle (Ascending and Descending)
Braking Information
Your power chair is equipped with two powerful brake systems:
1. Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
2. Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when
power is removed from the system for any reason.
Cornering Information
While your power chair is equipped with rear caster wheels in back and anti-tip wheels in front, excessively high
cornering speeds can still create the possibility of tipping. Factors which affect the possibility of tipping include, but
are not limited to: cornering speed, steering angle (how sharply you are turning), uneven road surfaces, inclined
road surfaces, riding from an area of low traction to an area of high traction (such as passing from a grassy area to
a paved area – especially at high speed while turning), and abrupt directional changes. High cornering speeds are
not recommended. If you feel that you may tip over in a corner, reduce your speed and steering angle (i.e., lessen
the sharpness of the turn) to prevent your power chair from tipping.
8
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
WARNING! When cornering sharply, reduce your speed. This greatly reduces the possibil-
ity of a tip or fall. To avoid personal injury and/or property damage, always exercise com-
mon sense when cornering.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces
composed of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will
encounter other surface types. For this reason, your power chair is designed to perform admirably on packed soil,
grass, and gravel. Feel free to use your power chair safely on lawns and in park areas.
n Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.
n Avoid tall grass that can entangle the running gear.
n Avoid loosely packed gravel and sand.
n If you feel unsure about a driving surface, avoid that surface.
Freewheel Mode
Your power chair is equipped with a manual freewheel lever to allow for manual maneuverability by a trained
attendant. For more information about how to place your power chair into and out of freewheel mode, see IV.
“The Jazzy 1122.”
WARNING! Do not use your power chair in freewheel mode without an attendant present.
Personal injury may result.
WARNING! Do not attempt to personally place your power chair in freewheel mode while
seated on it. Personal injury may result. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline. The
chair could roll uncontrollably on its own, causing personal injury.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs,
porches, stairs, etc.). The correct method for approaching a curb is illustrated in figure 1a.
Figure 1a. Correct Curb Approach (Correct and incorrect)
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
9
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is
higher than two inches unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed backward down any step,
curb, or other obstacle. This may cause the power chair to tip and cause personal injury.
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be
aware that it may be difficult for traffic to see you when you are seated on your power
chair. Obey all local pedestrian traffic rules. Wait until your path is clear of traffic, and
then proceed with extreme caution.
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators. You may cause
injury to yourself and to others and/or damage your power chair.
Doors
n Determine if the door opens toward or away from you.
n Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently
and slowly backward to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
n If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or
allow the rubber door edge to contact the power chair and the door will reopen.
n Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
EMI & RFI
Laboratory tests performed by the Food and DrugAdministration (FDA) have shown that radio waves can cause
unintended motion of electric mobility vehicles. Radio waves are a form of electromagnetic energy (EM). When
EM adversely affects the operation of an electronic device, it is called Electromagnetic Interference (EMI) or
Radio Frequency Interference (RFI). For more information, see III. “EMI/RFI.”
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in
transportation. Pride recommends that you closely review the instructions, specifications, and safety information
set forth by the manufacturer of the lift/elevation product before using that product.
10
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Motor Vehicle Transport
Currently, there are no standards approved for tie-down systems in a moving vehicle of any type to transport a
person while seated in a power chair.
Transfers
Transferring onto and off of your power chair requires a good sense of balance.Always have an attendant or
healthcare professional present while learning to properly transfer yourself.
To eliminate the possibility of injury, Pride recommends that you or a trained attendant perform the following tasks
before attempting a transfer:
n Reduce the distance between your power chair and the object you are transferring onto.
n Turn the power off. See VIII. “Operation.”
n Ensure your power chair is not in freewheel mode. See IV. “The Jazzy 1122.”
n Turn both caster wheels toward the transfer destination to improve power chair stability during transfer.
n Make sure both armrests are flipped up or removed from your power chair.
n Flip the footrest up, or move the leg rests aside; this will help to keep your feet from getting caught on the
footrest or the leg rests during the transfer.
WARNING! Before transferring, position yourself as far back as possible in the power
chair seat to prevent the power chair from tipping forward during transfer and causing
injury.
WARNING! Avoid using your armrests for weight bearing purposes. Such use may cause
the power chair to tip and cause personal injury.
WARNING! Avoid putting all of your weight on the footrest. Such use may cause the power
chair to tip and cause personal injury.
Positioning Belts
Your authorized Pride provider, therapist(s), and other healthcare professionals are responsible for determining
your requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure
it is fastened securely. Serious personal injury may result if you fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle.
Nor is your Jazzy suitable for use as a seat in any vehicle. Anyone traveling in a vehicle
should be properly belted into seats approved by the vehicle manufacturer.
WARNING! Do not sit on your power chair while it is in a moving vehicle. Personal injury
and/or property damage may result.
WARNING! Always be sure your power chair and its batteries are properly secured when it
is being transported. Failure to do so may result in personal injury and/or damage to your
power chair.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
11
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Inclement Weather Precautions
WARNING! Pride recommends that you do not operate your power chair in icy or slippery
conditions or on salted surfaces (i.e., walks or roads). Such use may adversely affect the
performance and safety of your power chair, resulting in an accident and personal injury.
WARNING! Do not expose your power chair to any type of moisture at any time (rain, snow,
mist, or wash). Such exposure can damage your power chair. Never operate your power
chair if it has been exposed to moisture until it has dried thoroughly.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while
seated on your power chair, it is important to maintain a stable center of gravity and keep the power chair from
tipping. Pride recommends that the power chair user determine his/her personal limitations and practice bending
and reaching in the presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the floor by
reaching down between your knees. Movements such as these may change your center of gravity
and the weight distribution of the power chair. This may cause your power chair to tip, possibly
resulting in personal injury. Keep your hands away from the tires when driving.
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For
more information about your power chair’s batteries, see IX. “Batteries and Charging.”
WARNING!Powerchairbatteriescanweighapproximately60poundseach. Ifyouareunabletolift
that much weight, be sure to get help. Lifting beyond your capacity can result in personal injury.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
WARNING!Always protect the batteries from freezingandnever chargeafrozen battery. Charging
a frozen battery may result in personal injury and/or damage to the battery.
Preventing Unintended movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time,
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This
will also eliminate the possibility of unintended chair movement from electromagnetic (EM)
sources. Failure to do so may result in personal injury.
12
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I . S A F E T Y
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety
issues when taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or if
you have certain physical limitations. Some medications and limitations may impair your ability to
operate your power chair in a safe manner.
Alcohol
The power chair user must exercise care and common sense when operating his/her power chair. This includes
awareness of safety issues while under the influence of alcohol.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts. Personal
injury and/or damage to the power chair may result.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
13
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . E M I / R F I
Laboratory tests performed by the Food and DrugAdministration (FDA) have shown that radio waves can cause
unintended motion of powered wheelchairs. Radio waves are a form of electromagnetic energy (EM). When this
energy adversely affects the operation of an electronic device, it is called Electromagnetic Interference (EMI)
or Radio Frequency Interference (RFI).
WARNING! Radio waves may interfere with the control of powered wheelchairs.
EMI/RFI—FREQUENTLY ASKED QUESTIONS (FAQS)
The following FAQs summarize what you should know about EMI/RFI. Use this information to minimize the risk
that EMI/RFI will affect your power chair.
Where do radio waves come from?
Radio waves are emitted from the antennas of cellular phones, mobile two-way radios (such as walkie-talkies),
radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links, microwave sources, and
paging transmitters. Radio waves are a form of EM. Because electromagnetic energy is more intense closer to the
transmitting antenna (source of emission), the EM fields from two-way radios are of special concern to power
chair users.
If my power chair is affected by EMI/RFI, what kind of motion should I expect?
This is hard to predict. It would depend on a number of factors:
n Strength of the radio waves
n Construction of the power chair
n Position of the power chair (whether it is on level ground or on an incline)
n Whether or not the power chair is in motion
An affected wheelchair’s movement can be erratic. It may move by itself or come to a sudden stop. Furthermore,
it is possible for EMI/RFI to unexpectedly release the brakes on a power chair. Some intense sources of EMI/RFI
can even damage the control system of your Jazzy.
Is there any way to know for sure whether radio waves are responsible for the unintended motion
of my power chair?
Unfortunately, interference from radio wave sources may be difficult to recognize, since the signals from these
sources are invisible and may be intermittent. However, the FDArecommends that you report all incidents of
unintended motion or brake release to the power chair manufacturer and, if possible, note whether there was a
radio wave source nearby at the time of the incident.
Has anyone been hurt from erratic, unintended motion of powered wheelchairs?
The FDA has reports of injuries that resulted from the apparent uncontrolled motion of powered wheelchairs.
However, it is unclear how many of these incidents were actually caused by radio wave interference.
14
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I I I . E M I / R F I
Are all powered wheelchairs susceptible to EMI/RFI?
Each make and model of chair differs in its ability to resist electromagnetic interference. That is, each has a
particular level of “immunity” to interference, measured in volts per meter (V/m).Ahigher immunity level offers
greater protection. In other words, a power chair with a high immunity level is less likely to be affected by a strong
radio source than one with a low immunity level.
What is the FDA doing about the problem?
The FDA has written power chair manufacturers and requested that they test their new products to be sure that
they provide a reasonable degree of immunity against EMI/RFI. The letter states that powered wheelchairs should
have an immunity of at least 20 V/m. This provides a reasonable degree of protection against the common sources
of EMI/RFI.
The FDA has also requested that these manufacturers clearly label their products with the immunity level, or state
that the immunity level is not known. The labeling and informational material supplied with the power chair must
explain what the immunity level means, and the labeling or informational material must warn users about the possi-
bility of EMI/RFI and how to avoid it. In addition, the FDA has recommended that manufacturers establish an
educational program to inform power chair users and their caregivers about the problems associated with EMI/
RFI, and the actions they can take to minimize the risk.
What can I do to find out if my power chair is likely to be affected by EMI/RFI?
If you’ve had your power chair for a long time and haven’t experienced any unintended motion, it is not likely that
you will have problems in the future. But it is always possible that problems could arise if you are close to a source
of radio waves. Therefore, it is very important to be alert to this possibility. The Jazzy meets or exceeds an
immunity level of at least 20 V/m.
What can I do to reduce the risk that my power chair could be affected by EMI/RFI?
Here are some precautions you can take:
n Do not turn on or use hand-held personal communications devices, such as citizens band (CB) radios and
cellular phones, while the power chair is on.
n Be aware of nearby transmitters, such as radio or TV stations and hand-held or mobile two-way radios, and try
not to come close to them. For example, if you are in a power chair with an immunity level of 20 V/m, you should
remain at least three feet from a hand-held two-way radio and ten feet from a mobile two-way radio.
n Be aware that adding accessories and/or components, or modifying the power chair, may make it more sus-
ceptible to interference from radio wave sources. There is no easy way to evaluate their effect on the overall
immunity of the power chair.
What should I do if my power chair moves unexpectedly?
If unintended motion or brake release occurs, turn the power chair off as soon as it is safe to do so.
If my power chair moves unexpectedly, where should I report this?
Call Pride at 800-424-8295 to report the incident.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
15
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . T H E J A Z Z Y 1 1 2 2
Your Jazzy has two main assemblies: the seat and the power base. See figure 1b. There are a variety of seating
options that are designed to accommodate most users. Typically, the seating assembly includes the armrests,
seatback, and joystick controller. Your Jazzy may also have some optional accessories attached to it, such as a
basket, a cane/crutch holder, a cup holder, or a power seat switch. See XI. “OptionalAccessories.”
The power base assembly is the heart of your Jazzy. The power base assembly includes two drive wheels, two
anti-tip wheels, two rear caster wheels, a power seat connector (optional), harness connectors, and a body
shroud. See figures 1b through 5.
SEATBACK
ARMRESTS
SEAT ASSEMBLY
CONTROLLER
FREEWHEELLEVER
(REAR)
BODY SHROUD
POWER BASE ASSEMBLY
FOOTREST
REAR CASTER WHEEL
ANTI-TIP WHEELS
DRIVEWHEEL
Figure 1b. The Jazzy 1122
16
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . T H E J A Z Z Y 1 1 2 2
ARMREST WIDTH
ADJUSTMENT KNOBS
Figure 2. The Jazzy 1122 Rear View
Figure 3. Remote Plus Controller Harness Connector
Figure 5. Europa Remote Controller Harness
Connector
Figure 4. Pilot Controller Harness Connector
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
17
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . T H E J A Z Z Y 1 1 2 2
ELECTRONICS TRAY
The electronics tray is located on the rear of your Jazzy. The electronics tray is located underneath the rear sliding
door. The electronics tray consists of the ammeter, the battery charger plug, the main circuit breaker, accessory
connector (optional equipment), and the controller harness connectors.
n Ammeter: The ammeter displays the charger’s current output in amps. For more information, see IX. “Bat-
teries and Charging” in this manual.
n Battery Charger Plug: This plug is used whenever your battery needs recharging.
n Main Circuit Breaker:The main circuit breaker is a safety feature built into your Jazzy. When the batteries
and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent
damage to the motors and the electronics. If the circuit trips, allow your Jazzy to “rest” for approximately one
minute. Next, push in the circuit breaker button, turn on the joystick controller, and continue normal operation.
If the main circuit breaker continues to trip repeatedly, contact your authorized Pride provider.
n Accessory Connector (Optional): This is where the optional harness connects to the controller (power seat,
lighting).
n ControllerHarness Connectors: This is where the joystick connects to the motors, batteries, and charger.
If your Jazzy is equipped with a Remote Plus or Europa controller, there is only one connector on the tray. If
your Jazzy is equipped with a Pilot controller, there are two connectors on the tray. See figures 3 through 5 to
view the controller harness connectors.
n Power Seat Connector (Optional): This is for the optional power seat switch. See figure 6.
REMOTE PLUS CONTROLLER HARNESS CONNECTOR
MAIN
CIRCUIT
BREAKER
OPTIONAL POWER SEAT
CONNECTOR LOCATION
AMMETER
BATTERY CHARGER PLUG
Figure 6. Electronics Tray
18
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . T H E J A Z Z Y 1 1 2 2
FREEWHEEL LEVER
For your convenience, your Jazzy is equipped with a freewheel lever. See figures 7 and 8. This lever allows you to
disengage the drive motors and maneuver the chair manually.
WARNING! Do not use your Jazzy while the drive motors are disengaged unless you are in
the presence of an attendant! Do not disengage the drive motors when your Jazzy is on an
incline. The chair could roll down on its own, causing injury!
To operate the manual freewheel lever:
1. Pull the manual freewheel lever out and rotate clockwise for freewheel mode (drive disengaged.) See figure 7.
2. Rotate the manual freewheel lever counterclockwise for drive mode (drive motors engaged.) See figure 8.
CAUTION! It is important to remember that when your Jazzy is in freewheel mode, the
braking system is disengaged.
NOTE: If a lever is difficult to move in either direction, rock your Jazzy back and forth slightly. The lever
should then move to the desired position.
Figure 7. Freewheel Mode
Figure 8. Drive Mode
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
19
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . T H E J A Z Z Y 1 1 2 2
ACTIVE-TRAC SUSPENSION
Your Jazzy is equipped with Active-Trac Suspension (ATS). ATS is a suspension system designed to make your
Jazzy traverse different types of terrain and obstacles while maintaining smooth operation. WithATS, your front
anti-tip wheels work in conjunction with your motor suspension to help you maneuver over obstacles.
As your front anti-tip wheels come in contact with an obstacle, the front anti-tip wheel assembly is drawn upward.
At the same time, your motors are forced downward. This allows the motors to push the Jazzy over an obstacle
and limits the possibility of your power chair getting caught on the obstacle.
ATS also helps in day-to-day operating conditions. For instance, when you release the joystick your Jazzy begins
to slow down. As the chair slows down, the front anti-tip wheels will automatically drop toward the ground. This
will reduce the forward tip that is typically encountered with center-wheel drive chairs.
REAR SUSPENSION
Your Jazzy 1122 is equipped with Rear Suspension. See figure 9. This suspension system works in conjunction
with theATS and is designed to maintain a smooth ride when driving over rough terrain and up and down curbs.
This system works by allowing the caster forks to respond to weight transfers and uneven terrain. The rear caster
wheelswillpivotasyoudriveoverobstacles. Thissystemalsoenhances performance when the front anti-tip wheels
are set lower to the surface.
REAR
CASTER
FORK
REAR
CASTER
WHEEL
Figure 9. Rear Suspension System
20
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I V . T H E J A Z Z Y 1 1 2 2
Specifications
Suspension:
Active-Trac system and caster suspension
14 in., pneumatic, center-mounted (solid tires are optional)
8 in., solid, rear articulating
6 in., solid, front mounted
Drive Wheels:
Caster Wheels:
Anti-tip Wheels:
Maximum Speed:
Brakes:
Up to 6 mph (up to 4.5 mph w/ high torque motors)
“Intelligent Braking,” electronic regenerative, disc park brake
3.25 in.
Ground Clearance:
Turning Radius:
Overall Size:
21 in.
Length: 40.5 in.
Width: 25.4 in.
Seating Options:
Medium-back (standard)
High-back with headrest (standard)
Reclining Seat (optional)
Synergy Seat (optional)
Versa Tilt Seat (optional)
Power-elevating Seat (optional)
Two motor, mid wheel
Drivetrain:
Batteries:
Two 12-volt, Group 24 batteries
(NF-22 batteries for the power seat option)
Up to 25 miles
Range:
Battery Charger:
5-amp, onboard
5-amp, off-board (optional)
70-amp P & G Pilot Controller
70-amp P & G Remote Plus Controller
70-amp Dynamic Europa Remote Controller
300 lbs.
Electronics:
Weight Capacity:
Jazzy Weights:
Base: 129 lbs.
Seat: 40 lbs. (standard seat)
Batteries: 53.5 lbs. each
Warranty:
Lifetime limited warranty on frame
Two-year warranty on electronics
Eighteen-month warranty on drive motors
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
21
Download from Www.Somanuals.com. All Manuals Search And Download.
V . A S S E M B L Y
FRONT
SEAT
TOWERS
SEAT INSTALLATION (SEAT WITH H-FRAME)
Thestandardseatinstallationmethodincorporatestheseatframe(H-
frame) and four (4) adjustable seat posts located on the power base.
REAR SEAT TOWERS
WARNING! Do not pick up the seat frame by the
armrests. They are free to pivot, and you may
lose control of the seat if they do so, resulting in
personal injury and/or damage to the chair.
To install the seat:
1. Set the seat on the rear seat towers. See figure 10.
2. Push the seat back and down until the latches engage on the
front seat towers. See figure 10.
3. Plug the controller cable into the connector on the electronics
tray. See figure 11.
4. Plug the power seat switch cable (if so equipped) into the
connector on the electronics tray.
5. Secure the controller cable to the armrest receiver with one
or more wire ties.
Figure 10. Seat Towers
6. Route the cable to ensure that the cable cannot be pinched in
the seat hinge.
CONTROLLER CABLE
JOYSTICK INSTALLATION
Depending on the various configurations and options you have
chosen for your Jazzy, it may have been shipped without the joy-
stick module installed in the armrest.
To install the joystick:
1. Use a 3/16-in. hex key to loosen the setscrew. See figure 12.
2. Slide the joystick mounting bracket into or out of the armrest
to the desired position.
3. Retighten the setscrew.
Figure 11. Controller Cable Connection
CAUTION! Do not place the controller cable so
that it can be pinched in the seat frame or power
base frame.
22
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V . A S S E M B L Y
POWER SEAT OPTION INSTALLATION
Your Jazzy may be equipped with the power seat option. While the
seat itself may be any one of the styles offered for this model, the way
the seat base attaches to the Jazzy power base is different.
SLIDE JOYSTICK
INTO BRACKET
To install the power seat:
l. Align the seat shaft to the hole in the actuator. See figure 13.
2. Insert seat into actuator and push the seat lever forward.
3. Lock seat into place.
SETSCREW
SYNERGY SEAT OR VERSA TILT OPTION
IfyourJazzyisequippedwithaSynergySeatorVersaTilt, pleaserefer
totheinstructionmanualsuppliedwiththeSynergy Seat/VersaTilt.
Figure 12. Joystick
POWER SEAT ACTUATOR
Figure 13. Power Seat Actuator
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
23
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . C O M F O R T A D J U S T M E N T S
SEAT
TOWER
Once you are familiar with your Jazzy’s operation, you may find the need
BALL DETENT
to adjust your seating position. There are some adjustments you can make
to increase your comfort, such as seat height and angle, armrest width,
armrest angle and height, joystick position, and footrest height, depth and
angle.
CAUTION! If your Jazzy was configured at your au-
thorized Pride provider or service center, please con-
sult your health care professional before changing
the seat position or making any other adjustment.
Some adjustments may degrade your Jazzy’s perfor-
mance and safety by changing its center of gravity.
Figure 14. Seat Height
SEAT HEIGHT AND SEAT ANGLE ADJUSTMENT
You can change the seat height to one of five positions in 1-in. increments.
SEAT
HINGE
BOLT
To change the seat height or seat angle:
1. Unplug the electrical connector(s).
2. Remove the seat. See “Seat Removal.”
3. Remove the power base front cover.
4. Use a slotted screwdriver to rotate the power base middle cover fas-
teners one-quarter turn and remove the power base middle cover.
5. Removetheballdetentpinfromeachofthefourseatposts. Seefigure14.
6. Raise or lower each seat post to the desired position. To change the
angle (dump), set either the front or rear seat posts higher or lower
than the other.
Figure 15. Seatback Angle
ADJUSTMENT KNOBS
7.Reinstall the ball detent pin into each seat post.
8.Reinstall the power base middle cover and front cover.
9.Reinstall the seat.
10.Plug the connectors into the electronics tray.
SEATBACK ANGLE ADJUSTMENT
If your power chair is equipped with an adjustable seatback, you can
adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.
Figure 16. Armrest Width
To adjust the seatback angle:
1. Use a hex key and a wrench to remove the adjusting screws on both
JAM NUT
seat hinges. See figure 15.
2. Set the seatback at desired angle.
3. Reinstall the screws on both seat hinges and tighten.
ADJUSTING
SCREW
Figure 17. Armrest Angle
24
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . C O M F O R T A D J U S T M E N T S
ARMREST WIDTH
To change the armrest width:
1. Locate the two adjustment knobs on the armrest receiver bracket.
See figure 16.
2. Loosen the knobs.
JOYSTICK
MOUNTING
BRACKET
3. Slide the armrests in or out, to the desired width.
4. Tighten the knobs.
SETSCREW
ARMREST ANGLE
You can adjust the armrest angle to fit your specific needs.
To change the armrest angle:
Figure 18. Joystick Extension
1. Lift the armrest straight up so that it is perpendicular to the floor.
2. Use a 7/16-in. wrench to loosen the jam nut. See figure 17.
3. Use a 5/32-in. hex key to loosen the adjusting screw.
4. Turn the screw clockwise to lower the front of the armrest, or turn
the screw counterclockwise to raise the front of the armrest.
5. Locktheadjustingscrewintoplacebytighteningthejamnut.
ARMREST HEIGHT (OPTIONAL)
Your Jazzy may be equipped with height-adjustable armrests.
To change the armrest height:
1. Loosen the setscrew located underneath the armrest using a 3/16-
in. hex key.
2. Remove the ball detent pin from the armrest.
3. Move the armrest up or down to the desired height.
4. Align the holes and reinsert the ball detent pin.
5. Retighten the setscrew.
Figure 19. Swing-Away Joystick
(Forward Position)
JOYSTICK EXTENSION
The joystick can easily slide out away from the armrest or in toward
the armrest.
To extend the joystick :
1. Use a 3/16-in. hex key to loosen the setscrew. See figure 18.
2. Slide the joystick mounting bracket into or out of the armrest to the
desired position.
3. Retighten the setscrew.
Figure 20. Swing-Away Joystick
(Retracted Position)
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
25
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . C O M F O R T A D J U S T M E N T S
NUTS AND BOLTS
SWING-AWAY JOYSTICK
Your Jazzy may be equipped with a swing-away joystick. This
option enables you to move the joystick from the front of the arm-
rest to the side of the armrest, without disconnecting it. See figures
19 and 20.
The joystick can be mounted to the left or right side of your Jazzy.
Contact your authorized Pride provider.
FOOTREST HEIGHT
The footrest height is easily adjusted to one of six different heights
in 1-in. increments.
Figure 21. Footrest Height
To raise or lower the footrest:
1. Remove the nuts and bolts from bracket. See figure 21.
2. Raise or lower the footrest to the desired height.
3. Reinstall the bolts and nuts into the footrest bracket and tighten.
SETSCREW
FOOTREST DEPTH
To adjust the footrest depth:
1. Remove the nuts and bolts from the bracket. See figure 21.
2. Move the footrest in or out to the desired depth.
3. Reinstall the nuts and bolts into the bracket and tighten.
FOOTREST ANGLE
You can adjust the angle of the footrest with a 3/16-in. hex key.
Figure 22. Footrest Angle
See figure 22.
To adjust the footrest angle:
1. Turn the setscrew clockwise to raise the front of the footrest.
2. Turnthesetscrewcounterclockwisetolowerthefrontofthefootrest.
SFR
RELEASE
LEVER
SWING-AWAY FOOTRESTS OPTION
Swing-away footrests (SFRs) are an option. They enable you to
swing the footrest to the side before transferring from your Jazzy.
To swing the footrests:
1. Push in the SFR release lever. See figure 23.
2. Swing the footrest off to the side.
Figure 23. Swing-Away Footrests
26
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . C O M F O R T A D J U S T M E N T S
ELEVATING LEG RESTS OPTION
Elevating Leg Rests (ELRs) offer an infinite range of adjustment
between 0º – 70º for the leg angle and a leg rest adjustment range of
ELR
RELEASE
15 – 20 in.
LEVER
To adjust the ELR angle:
1. Press the ELR release lever. See figure 24.
2. Move the leg rest to the desired angle.
To adjust the ELR length:
1. Remove the two screws from the side of each leg rest exten-
sion. See figure 25.
2. Slide the leg rest in or out to the desired length.
3. Reinstall the two screws on each leg rest extension.
Figure 24. Elevating Leg Rests
RECLINING SEAT OPTION
If your Jazzy is equipped with a reclining seat (see figure 26), you
can adjust the seatback angle and the armrest angle.
LEG REST
ADJUSTMENT SCREWS
To adjust the seatback angle:
1. Press down on the seatback release lever. See figure 27.
2. Move the seatback down or up to the desired position.
3. Release the seatback release lever.
To adjust the armrest angle:
Refer to “Armrest Angle” earlier in this section.
POWER ELEVATING SEAT OPTION
Figure 25. Elevating Leg Rests
If your Jazzy is equipped with a power elevating seat, you can change
the seat height automatically. The seat height switch is located either
on the armrest (Pilot or Europa controllers), or on the joystick (Re-
mote Plus or Dolphin controllers).
To change the seat height:
1. Press forward on the power seat switch to raise the seat. See
figure 28.
2. Pull back on the power seat switch to lower the seat.
CAUTION! Do not allow the motor to run more
than a few seconds after the mechanism
reaches the top or bottom limit.
Figure 26. Reclining Seat
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
27
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . C O M F O R T A D J U S T M E N T S
Power Seat Warnings and Cautions
WARNING! The power elevating seat option is
intended for use on a level surface only. Never
raise the seat from its lowest position on an in-
clined surface. Failure to heed this warning can
result in the Jazzy tipping over and causing in-
jury.
WARNING! Never raise the seat from its lowest
position when operating your Jazzy on bumpy or
uneven surfaces. Failure to heed this warning can
result in the Jazzy tipping over and causing in-
jury.
Figure 27. Seatback Angle
WARNING! Never raise the power elevating seat
while your Jazzy is in the freewheel mode.
CAUTION! Always fasten the positioning belt when
operating the power elevating seat. The power
elevating seat option is equipped with a system that
reducesyourJazzy’sspeedbyonehalfwhentheseat
is elevated more than 1 – 2 inches. Always check to
besurethissystemisoperatingproperlybeforeusing
your Jazzy.
POWER SEAT
SWITCH
HIGH-BACK WITH HEADREST (OPTIONAL)
If your Jazzy is equipped with the deluxe high-back seat, you can
adjust the headrest height.
Figure 28. Power Seat Switch
To adjust the headrest height:
1. Push in the headrest release button.
2. Move the headrest up or down to the desired position.
28
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I . C O M F O R T A D J U S T M E N T S
ANTI-TIP WHEEL ADJUSTMENT
The anti-tip wheels are designed to give your Jazzy increased stability
on rough surfaces. The anti-tip wheels are preset at the factory to a
height of 1/2-in. off the ground. This setting is for smooth surfaces or
indoor use only. If you plan on using your Jazzy on rough surfaces, it
may be necessary to adjust the anti-tip wheels to better suit your needs.
Theanti-tipwheelsmayneedadjustmentifeitherofthefollowingoccur:
n When coming to a stop, your Jazzy tips forward excessively.
n The anti-tip wheels constantly rub the ground.
Figure 29. Anti-Tip Wheel Adjustment
:
NOTE Each drive tire must have at least 30 - 35 lbs. of air pres-
sure in order for the anti-tip wheels to be properly adjusted.
To adjust the anti-tip wheels:
1. Place a 1/2-in. wrench on the inner locknut of the anti-tip bracket
located right after your shock strut. See figure 29.
2. Turn the locknut counterclockwise to loosen.
3. Place your 1/2-in. wrench on the adjustable cam located on the
other side of the locknut. See figure 30.
4. To adjust the anti-tip upward, turn the cam counterclockwise. To
adjust the anti-tip downward, turn the cam clockwise.
WARNING! Consult your authorized Pride provider
before attempting to change the anti-tip height!
Changing the anti-tip wheel height affects handling
underdeceleration!
Figure 30. Anti-Tip Wheel Adjustment
WARNING! The higher you raise the anti-tip wheels,
themoretendencyyourJazzyhastotiltforwardwhen
coming to a stop. You can compensate for this by
making a small adjustment to the pre-programmed
deceleration setting in the controller or by moving the
seat assembly further to the rear of your Jazzy.
Failure to do so may result in personal injury.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
29
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I . D I S A S S E M B L Y
SEAT REMOVAL
You may wish to remove the seat for transportation. If you have
a Versa Seat, please refer to the Versa Seat Installation andAd-
justment guide.
To remove the seat:
1. Turn the power off.
2. Make sure your Jazzy is not in freewheel mode.
3. Unplug the main wire harness behind the seat.
4. Simultaneously depress the two plungers on the front of the
seat frame while lifting the front of the seat. See figure 31.
5. Lifttheseatupandgentlyloweritbackontothefrontseattowers.
6. Pull the seat forward and lift it off of the rear seat towers.
Figure 31. Removing the Seat
To remove a power seat:
1. Release the seat by moving the seat release lever rearward.
2. Lift up the power seat plate.
3. Lift the seat off of the actuator.
FOOT FRAME REMOVAL
The foot frame helps protect the Jazzy components from the envi-
ronment. See figure 32.Youmust remove the foot frame in order
to change the batteries and check the cable connections.
To remove the foot frame:
1. Turn the power off.
2. Make sure your Jazzy is not in freewheel mode. See IV.
“The Jazzy 1122.”
Figure 32. Removing the Foot Frame
3. Locate the 5/16-in. pin at the base of the footplate bracket
and remove.
4. Lift the foot frame straight up approximately 2 inches and
pull toward you.
30
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
PILOT CONTROLLER
The electronic controller is what you use to operate your power chair. It takes the battery voltage and sends it to
the appropriate system. The electronic controller also enables you to monitor battery charge, electronic controller
functions, and the condition of your electrical system.Also, it may be used to control some optional systems such
as power elevating seats and lights.
The Pilot electronic controller is an integral
electronic controller.All of the electronics nec-
1
essary to operate the power chair are con-
tained in one module. See figure 33.
2
4
3
The Pilot consists of:
1. joystick
2. on/off button
3. battery condition meter
4. speed control knob
5. off-board charger/programming socket
6. controller connector
7. 3-pin charger inhibit connector
6
7
5
Typically, the Pilot is mounted to one of the
armrests and is connected to the motors, bat-
teries, and the onboard charger at the elec-
tronics tray.
Figure 33. Pilot Controller
Joystick
The joystick controls the direction and speed of your power chair. When you move the joystick from the neutral
(center) position, the electromagnetic brakes release and allow your power chair to move. The further you push the
joystick from its neutral position, the faster your power chair moves. When you release the joystick and allow it to
return to the netural position, you engage the electromagnetic brakes. This causes your power chair to decelerate
and come to a complete stop.
WARNING! If your power chair begins to move in an unexpected manner, immediately
release the joystick. Unless the joystick is damaged, this action should stop your power
chair.
On/Off Button
This is a green button located in front of the joystick. It turns the Pilot on and off.
WARNING! Unless faced with an emergency situation, do not use the on/off push button to
stop the chair. This will cause the power chair to stop abruptly.
WARNING! Always turn the power off when you are stationary to prevent unexpected
movement.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
31
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
Battery Condition Meter
The battery condition meter is located in front of the joystick. This is a 10-segment illuminated display that indicates
that the Pilot is turned on and also gives the battery status, the Pilot status, and the electrical system status.
n Red, yellow, and green lights lit: Battery charged; Pilot and electrical system OK.
n Red and yellow lights lit: Charge battery if possible; Pilot and electrical system OK.
n Red lights only lit or slow flash: Charge battery as soon as possible; Pilot and electrical system OK.
n Rapid flash of lights: Indicates a fault in the Pilot or the electrical system. Refer to “Pilot Error Codes.”
n Ripple up and down of lights: The joystick was not in the neutral position when the controller was turned on.
If you get “ripple up and down of lights”, turn off the controller, allow the joystick to return to the neutral
position, then turn on the controller.
NOTE: If you still get “ripple up and down of lights”, contact your authorized Pride Provider.
NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash,
reminding you the batteries need to be charged immediately!
Speed Control Knob
Sets the maximum speed of the power chair: clockwise to increase, counterclockwise to decrease.
NOTE: We recommend that the first few times you operate your power chair, you turn the speed control
to the slowest setting until you become familiar with your new power chair.
Off-board Charger/Programming Socket
You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front
of the Pilot. If you use an off-board charger, the charger current should not exceed 12 amps. Contact your
authorized Pride provider for more information.
CAUTION! Only chargers with Neutrik NC3MX plugs should be connected to the offboard
charger/programming socket. See your authorized Pride provider for more information.
NOTE: The offboard charger/programming socket may also be used for reprogramming the Pilot.
Contact your authorized Pride provider for more information.
Controller Connector
This connects the Pilot to the power chair’s batteries, motors, and motor brakes.
3-pin Charger Inhibit Connector
This connects the Pilot to the onboard battery charger. This connection provides an inhibit that disables the Pilot
when the battery charger is on. The charger inhibit connector is coded with colored dots. The dots are positioned
so that you align the flat side of the male connector with the flat side of the female connector before making the
connection.
32
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
CAUTION! Failure to properly align the connectors can result in damage to the Pilot, the
charger harness, and the connectors.
Thermal Rollback
The Pilot is equipped with a thermal rollback circuit. This circuit monitors the temperature of the motors and the
Pilot. In the event that either one of the motors or the Pilot becomes excessively hot (above 122° F), the Pilot
reduces the motor voltage. For every degree above 122° F, the controller reduces the voltage by 5 volts. This
reduces your power chair’s speed and allows the electrical components to cool down. When the temperature
returns to a safe level, your power chair resumes its normal speed.
WARNING! Under strenuous driving conditions, it is possible for the bottom and side case
temperature of the Pilot to exceed 105° F. DO NOT touch the side or bottom of the Pilot
case under these circumstances.
Trouble Codes
In addition to indicating the current state of battery charge, the battery condition meter can also indicate possible
problems with your power chair. The battery condition meter has ten lights. The lights provide information by the
number of lights that are flashing. If any of the meter lights are flashing rapidly, the controller may be indicating a
fault. For instance, if the first light is flashing rapidly, the battery voltage is nearly depleted. The following is a list of
the possible errors signified by the rapidly flashing meter. When you get a trouble code, contact your authorized
Pride provider.
FLASHING
LIGHTS
10
DIAGNOSIS
SOLUTION
High Battery Voltage
Solenoid Brake Fault
Controller
Check batteries.
9
Check motor/brake wiring.
8Possible
Fault
See
authorized
7
6
5
4
3
2
1
Possible Joystick Fault
InhibitActive
See authorized Pride provider.
Unplug charger. Check connections.
Check right motor wiring.
Right Motor Wiring Fault
Right Motor Disconnected
Left Motor Wiring Fault
Left Motor Disconnected
Low Battery Voltage
Check right motor wiring.
Check left motor wiring.
Check left motor wiring.
Check batteries/battery wiring.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
33
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
REMOTE PLUS CONTROLLER
The electronic controller is what you use to operate your power chair. It takes the battery voltage and sends it to
the appropriate system. The electronic controller also enables you to monitor battery charge, electronic controller
functions, and the condition of your electrical system.Also, it may be used to control some optional systems such
as power elevating seats and lights.
The Remote Plus is a modular electronic control system. The electronics necessary to operate the power chair are
contained in several modules located on different parts of your power chair.
The Remote Plus system consists of the following components:
n master remote
n communications cable(s)
n power module
n motor wiring harnesses
n battery wiring harnesses
n actuator lighting module (for optional equipment)
1
The master remote is located typically on the end
of an armrest. The other components are located
inside the power base.
2
Remote Plus Master Remote
The Remote Plus master remote consists of the fol-
lowing (see figure 34):
3
1. joystick
2. keypad
3. controller communications cable
4
4. off-board charger/programming socket
Figure 34. Remote Plus Master Remote
Joystick
The joystick controls the direction and speed of your power chair. When you move the joystick from the neutral
(center) position, the electromagnetic brakes release and allow your power chair to move. The further you push the
joystick from its neutral position, the faster your power chair moves. When you release the joystick and allow it to
return to the neutral position, you engage the electromagnetic brakes. This causes your power chair to decelerate
and come to a complete stop.
WARNING! If your power chair begins to move in an unexpected manner, immediately
release the joystick. Unless the joystick is damaged, this action should stop your power
chair.
Keypad
The keypad is located directly in front of the joystick. See figure 35. It contains keys that you will use to control
your power chair.
34
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
On/Off Key
The on/off keys toggles the system power on and off.
WARNING! Unless faced with an emer-
gency situation, do not use the on/off
key to stop the chair. This will cause
the power chair to stop abruptly.
WARNING! Always turn the power off
when you are stationary to prevent un-
expected movement.
Mode Key
Press the key to change speed setting or to activate the
power accessories. See “Speed Settings” or “Power
Accessories.”
Speed Setting Indicator
Indicates the selected speed setting.
Power Accessory Indicator
Indicates the selected power accessory. This is for op-
tional accessories only.
Horn Key
The horn key activates the horn.
Figure 35. Remote Plus Keypad
Right/Left Turn Indicator Keys
The right/left Indictor keys toggle either the left or right turn indicators. Press once to turn on and press again to turn
off.You can also turn off the selected indicator by pressing the opposite indicator key or the hazard key.
Light Key
The light key turns headlights/taillights on and off independent of other indicators.
Hazard Key
The hazard key toggles both right and left indicators at the same time. You can only cancel this by pressing the
hazard key again.
Battery Condition Meter
The battery condition meter is located in front of the joystick. This is a 10-segment illuminated display that indicates
that the Remote Plus is turned on and also gives the status of the battery, the controller, and the power chair
electrical system.
n Red, yellow, and green lights lit: Battery charged; controller and electrical system OK.
n Red and yellow lights lit: Charge battery if possible; controller and electrical system OK.
n Red lights only lit or slow flash: Charge battery as soon as possible; controller and electrical system OK.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
35
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
n Rapid flash of lights: Indicates a fault in the controller or the electrical system.
n Ripple up and down of lights: The joystick was not in the center position when the controller was turned on. If
you get “ripple up and down of lights”, turn off the controller, allow the joystick to return to the neutral position,
then turn on the controller.
NOTE: If you still get “ripple up and down of lights”, contact your authorized Pride Provider.
NOTE: When the batteries approach a discharged state, the first red light will begin to slowly flash,
reminding you the batteries need to be charged immediately!
Speed Settings
The Remote Plus speed settings range from 1 to 5. Typically, the slowest speed setting is 1 and the fastest speed
setting is 5. The settings are indicated by the number of lights that are lit.
NOTE: The speed settings are preset at the factory. If your authorized Pride provider changes the order
of these settings, please make note of these changes. Contact your authorized Pride provider for more
information.
To select a speed setting:
1. Press the on/off key to power on the remote.
2. Press the mode key once.
3. To increase chair speed, push the joystick to the right. Each time you push the joystick, you will increase the
speed setting.
4. To decrease chair speed, push the joystick to the left. Each time you push the joystick, you decrease the speed
setting.
5. Once you select the desired speed setting, press the mode key once to keep the setting or push the joystick in
the forward or reverse direction. The chair will resume operation at the selected speed.
NOTE: We recommend that the first few times you operate your power chair, you have your speed on the
slowest setting until you become familiar with your new power chair.
Power Accessories
If your power chair is equipped with power accessories such as a power seat or power elevating leg rests, you can
operate them through the remote keypad. Contact your authorized Pride provider for information on how to
operate these accessories.
Off-board Charger/Programming Socket
You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front
of the controller. See figure 34. The socket may also be used for reprogramming the controller by using a Penny &
Giles Programmer, should this be necessary. If you use an off-board charger, the charger current should not exceed
12 amps. Contact your authorized Pride provider for more information.
36
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
CAUTION! Only chargers with Neutrik NC3MX plugs should be connected to the off-board
charger/programming socket.
Controller Communications Cable
The controller communications cable provides the joystick module with a connection to the power module at the
back of the power base. See figure 34.
Power Module
Typically, the power module is mounted to the power base. The power module provides a power interface for the
joystick module. It routes the battery power to the motors and other powered accessories such as lights and
power seats.
Actuator Lighting Module (Not Shown)
The actuator lighting module is also located on the power base. The actuator lighting module provides a control and
power interface between the power module, the lights, and/or the power seat actuator.
Sleep Mode
Your Remote Plus controller has a sleep mode feature. Sleep mode is a built-in circuit that automatically shuts off
the main power if the joystick is not moved in any direction for approximately five minutes. The battery condition
meter lights on the keypad indicate sleep mode by blinking once every five seconds. To restore power and con-
tinue, push the on/off key twice.
Thermal Rollback
The Remote Plus is equipped with a thermal rollback circuit. This circuit monitors the temperature of the motors,
power module, and remote. In the event that any of them become excessively hot (above 122° F), motor voltage
is reduced. For every degree above 122° F, the voltage is reduced by 5 volts. This reduces your power chair’s
speed and allows the electrical components to cool down. When the temperature returns to a safe level, your
power chair resumes its normal speed.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
37
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
Trouble Codes
In addition to indicating the current state of battery charge, the battery condition meter can also indicate possible
problems with your power chair. The battery condition meter has ten lights. The lights provide information by the
number of lights that are flashing. If any of the meter lights are flashing rapidly, the controller may be indicating a
fault. For instance, if the first light is flashing rapidly, the battery voltage is nearly depleted. The following is a list of
the possible errors signified by the rapidly flashing meter. When you get a trouble code, contact your authorized
Pride provider.
FLASHING
LIGHTS
DIAGNOSIS
SOLUTION
10
9
High Battery Voltage
Solenoid Brake Fault
Controller
Check batteries.
Check motor/brake wiring.
8Possible
Fault
See
See authorized Pride provider.
Check connections.
authorized
7
6
5
4
3
2
1
Possible Joystick Fault
InhibitActive Unplug charger.
Right Motor Wiring Fault
Right Motor Disconnected
Left Motor Wiring Fault
Left Motor Disconnected
Low Battery Voltage
Check right motor wiring.
Check right motor wiring.
Check left motor wiring.
Check left motor wiring.
Check batteries/battery wiring.
38
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
DXCONTROLLER
The Dynamic DX electronic control system is a modular system. The electronics necessary to operate the power
chair are contained in several modules located on different parts of your power chair.
The Dynamic DX system consists of the following components:
n master remote (Europa)
n communications cable(s)
n power module
n motor wiring harnesses
n battery wiring harnesses
n actuator lighting module (for optional systems)
The master remote is located typically on the end of an armrest. The other components are located inside the
power base.
1
Europa Master Remote
The Europa master remote consists of the following
(see figure 36):
1. joystick
2. keypad
2
3. controller communications connector
4. off-board charger/programming socket
3
1 / 0
Joystick
The joystick controls the direction and speed of the
power chair. When you move the joystick from the
neutral (center) position, the electromagnetic brake will
release and allow the power chair to move. The fur-
4
Figure 36. Europa Master Remote
ther you push the joystick from its neutral position, the faster your power chair will move. When you release the
joystick and allow it to return to the neutral position, you engage the electromagnetic brake. This helps the power
chair decelerate and come to a complete stop. You can also use the joystick control power actuators.
WARNING! If your power chair begins to move in an unexpected manner, immediately release the
joystick. Unless the joystick is damaged, this action should stop your power chair.
Out Of Neutral At Power Up
Your power chair joystick is equipped with Out Of Neutral At Power Up (OONAPU). If you power up the
system and the joystick is not in the neutral position, the system status ligjt flashes rapidly for either as long as the
joystick is out of the neutral position or five seconds. If this has happened and the all the segments on the battery
condition meter are flashing, you may have set a fault code. See “Trouble Codes.”
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
39
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
Keypad
The keypad is located directly in front of the joystick. It con-
tains keys that you will use to control your power chair. See
figure 37.
On/Off Key
The on/off key toggles the system power on and off.
WARNING! Unless faced with an emergency
situation, do not use the on/off key to stop the
chair. This will cause the power chair to stop
abruptly.
WARNING! Always turn the power off when you
are stationary to prevent unexpected
movement.
NOTE: If the joystick is not in the neutral (center) position
when you turn on the power, you may cause a fault in the
system. See “Out Of NeutralAt Power Up.”
Figure 37. Europa Master Remote Keypad
System Status Light
The system status light is normally on when the system is powered up, and off when the system is powered down.
It will also flash trouble codes when the system detects a fault. See “Trouble Codes.”
Magnetic Locking Area
Your power chair is equipped with a feature that enables you to “lockout” unauthorized users. For this function,
you will need the magnetic key supplied with your power chair. If you lose this key, contact your authorized Pride
provider.
To enable the lockout system:
1. Hold the magnetic key on or near the key symbol. The system will beep and automatically turn off.
NOTE: None of the remote lights should be lit.
2. Press the on/off key to turn on the power chair. The key symbol will flash, but you will not be able to drive your
power chair. This means that it is still locked.
3. Hold the magnetic key on or near the key symbol again to unlock the system. When the key symbol stops
flashing, you may turn on the power chair.
NOTE: If you turn on the power chair while it is locked and don’t unlock it after one minute, the power
chair will automatically turn off itself.
40
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
Battery Condition Meter
The battery condition meter consists of six lights arranged in an arc over the battery icon. From left to right, the first
two are red, the second two are orange and the last two are green. These lights give you an accurate indication of
your usable battery capacity. If the battery has at least 85% of its rated capacity, all of the lights will be on.As the
battery voltage drops, the number of lights reduces from right to left. When the battery capacity drops to 10% or
below, all of the lights will flash once every second.
Drive Program Select Key
The drive program select key enables you to select a drive program and an actuator mode. Your Dynamic DX
controller was preprogrammed at the factory for five drive programs— 1(slowest) to 5(fastest). The drive mode is
indicated by a number in the center of the keypad.
NOTE: The drive mode settings are preset at the factory. If your authorized Pride provider changes these
settings, please make note of these changes.
To change the drive mode program:
1. Press the drive mode select key.
2. Move the joystick right to increase the drive mode program.
3. Move the joystick left to decrease the drive mode program.
4. Press the drive mode select key.
Drive Mode and Actuator Display (also Remote Status Display)
This is a seven-segment light that displays the drive program. It also displays a drive inhibit and actuator mode (if
applicable), when they occur.
Actuator Select Keys with Lights
If your power chair is equipped with power accessories such as a power seat or power elevating leg rests, you can
operate them through the remote keypad. Contact your authorized Pride provider for information on how to
operate these accessories.
Remote Status Light
This light will flash if there is an internal Dynamic DX Remote fault, or if an OONAPU fault has occurred. See “Out
Of NeutralAt Power Up.”
Horn Key
The horn key activates the horn.
Battery Saver Feature
When the battery capacity drops to below 21V (typically two lights), the controller will reduce power chair
performance to conserve battery power.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
41
Download from Www.Somanuals.com. All Manuals Search And Download.
V I I I . O P E R A T I O N
Off-board Charger/Programming Socket
You may use an off-board charger to charge the power chair batteries through the 3-pin socket located on the front
of the Europa. See figure 36. If you use and off-board charger, the charger current should not exceed 8 amps.
Contact your authorized Pride provider for more information.
NOTE: The socket may also be used for reprogramming the Europa. Contact your authorized Pride
provider for more information.
Sleep Mode (If Enabled)
The power chair controller features a sleep mode. Sleep mode is a built-in circuit that will automatically shut off the
main power if the joystick is not moved in any direction for a period of time. This time factor is programmed into the
controller. To restore power and continue, push and key on the keypad.
Trouble Codes
The system status light is displayed within the on/off key. This light is lit if the system is turned on. It also flashes in
groups called trouble codes, to indicate system faults. The table below identifies the individual trouble codes. If
your keypad displays one of these codes, contact your authorized Pride provider.
TROUBLE CODE
SEQUENCE
DIAGNOSIS
DX module fault
SOLUTION
•—•—•—
See your authorized Pride provider.
See your authorized Pride provider.
Check left motor wiring.
••—••—••—
DX accessory fault
Left motor (or connection) fault
Right motor (or connection) fault
Left park brake fault
Right park brake fault
Low battery fault
•••—•••—
••••—••••—
Check right motor wiring.
•••••—•••••—
••••••—••••••—
•••••••—•••••••—
•••••••—•••••••—
•••••••—•••••••—
•••••••—•••••••—
•••••••—•••••••—
•••••••—•••••••—
Check motor/brake wiring.
Check motor/brake wiring.
Check that the battery wiring is secure.
Check that the battery wiring is secure.
See your authorized Pride provider.
See your authorized Pride provider.
Turn unit on, then off.
Over voltage fault
CANL fault
CANA fault
Stall timeout
Module mismatch
See your authorized Pride provider.
NOTE: You must turn the controller off and then on again to reset the controller, even if the source of the
fault is removed/corrected.
In the event of a fault, the system status light displays diagnostic indications. Faults are encoded as follows: one (for
a low battery voltage fault) to twelve (module mismatch) and are displayed by the light flashing the number of times
prescribed by the fault code. The flash sequence (one to twelve) is followed by a long off period (2 seconds). If
more than one fault exists, then the fault having the highest priority is indicated. The controller must be turned off
and then on again even if the source of the fault is removed. If you cannot resolve the problem, contact your
authorized Pride provider.
42
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I X . B A T T E R I E S A N D C H A R G I N G
BATTERIES
Your Jazzy uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free.
Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to
handle a longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not
interchangeable.Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for
use in powered wheelchairs.
WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wash hands after handling.
CHARGING THE BATTERIES
The battery charger is essential in providing long life for your Jazzy batteries. The battery charger is designed to
optimize your Jazzy’s performance by charging the batteries safely, quickly, and easily. The charging system con-
sists of the battery charger, the charger fuse, and the ammeter. The onboard charger is located underneath the
electronics tray. The ammeter and charger fuse are located on the electronics tray for easy viewing. See figures 38
and 39. The ammeter indicates the rate of charge being administered to fully recharge the batteries. It is also a good
indication of whether or not the charger is working. The ammeter and the charger are only functional when the
charger power cord is plugged into a wall outlet.
WARNING! You must recharge your Jazzy’s batteries with the supplied onboard or off-board
charging system. Do not use an automotive-type battery charger.
WARNING!Neveruseanextensioncordtopluginyourbattercharger. Plugthechargerdirectlyinto
a properly wired standard wall outlet.
CHARGER
FUSE
AMMETER
Figure 38. Ammeter
Figure 39. Charger Fuse
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
43
Download from Www.Somanuals.com. All Manuals Search And Download.
I X . B A T T E R I E S A N D C H A R G I N G
To charge the batteries using the onboard charger:
1. Position the rear of your Jazzy close to a standard wall outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See IV. “The
Jazzy 1122.”
3. Slide the rear cover forward.
4. Extend the charger power cord and plug it into the wall outlet. The Jazzy incorporates an inhibit function that
disables the power chair when the charger is plugged into a wall outlet.
5. The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute for the
charger to warm up. The ammeter may move as high as 5.5 amps, then gradually move back down to 0 amps
as the batteries charge.
6. We recommend you charge the batteries for 8 to 14 hours.As the batteries charge, the ammeter needle slowly
drops to zero. When the batteries are fully charged, the needle vibrates on or near the zero mark on the
ammeter scale.
7. When your Jazzy’s batteries are fully charged, you can unplug the power cord from the wall outlet, wind it up
using the hook and loop strap, and place the cord back into the rear tray.
8. Replace the rear cover.
To charge the batteries using the off-board charger:
1. Position your Jazzy next to a standard wall outlet.
2. Be certain the controller power is turned off.
3. Remove the run plug located on the electronics tray.
4. Plug the 3-pin extension cable into the charger, then into the electronics tray connector.
5. Plug the charger into the wall outlet.
6. The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute for the
charger to warm up. The ammeter should move all the way up to 5 amps, then gradually move back down to
0 amps.
7. We recommend you charge the batteries for 8 to 14 hours.As the batteries charge, the ammeter needle slowly
drops to zero. When the batteries are fully charged, the needle vibrates on or near zero on the ammeter scale.
8. When your Jazzy’s batteries are fully charged, disconnect the charger cord from the wall outlet.
9. Disconnect the charger from the rear electronics tray.
10. Reconnect the run plug into its connector.
:
NOTE If the run plug is not reconnected, your Jazzy will not run.
11. Replace the rear cover.
44
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I X . B A T T E R I E S A N D C H A R G I N G
BATTERYBREAK-IN
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak
performance level.
2. Operate your Jazzy about the house and yard. Move slowly at first, and don’t stray too far until you become
accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your Jazzy again. The batteries should now
perform at over 90% of their potential.
4. After four or five charging cycles, the batteries top off at 100% charge and last for an extended period.
BATTERIES AND CHARGING—FREQUENTLY ASKED QUESTIONS (FAQs)
How does the charger work?
The battery charger takes the standard wall outlet voltage of 120VAC (alternating current) and converts it to 24
VDC (direct current). The Jazzy batteries use direct current to run your power chair. When the battery voltage is
low, the charger works harder to charge the battery. This is why the ammeter initially reads 5 or more amps.As the
battery voltage approaches full charge, the charger doesn’t work as hard to complete the charging cycle. This
explains why the ammeter drops as it approaches a full charge. When the battery is fully charged, the amperage
from the charger is nearly at zero. This is how the charger maintains a charge but does not overcharge the battery.
Your Jazzy’s charger will not operate after the batteries have been discharged to nearly zero voltage. If this hap-
pens, call your authorized Pride provider for assistance.
Can I use a different battery charger?
Use only the charger supplied with the Jazzy. It is the safest, most efficient tool to charge the batteries. We do not
recommend using other types of chargers.
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries.You may use your Jazzy all day on
a daily basis or you may not use it for weeks at a time.
n Daily Use
If you use your Jazzy on a daily basis, charge the batteries as soon as you are finished.Your Jazzy will be ready
each morning to give you a full day’s service. It is recommended that you charge the batteries 8 to 14 hours
after daily use. Do not charge the batteries for more than 24 hours at a charging cycle.
n Infrequent Use
If you use your Jazzy infrequently (once a week or less), you should charge the batteries at least once per
week for 12 to 14 hours.
:
NOTE Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the
batteries for more than 24 hours at a charging cycle.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
45
Download from Www.Somanuals.com. All Manuals Search And Download.
I X . B A T T E R I E S A N D C H A R G I N G
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. More
often you are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind.All of
these factors affect the distance or running time per battery charge. The following are a few suggestions for obtain-
ing the maximum range per charge.
n Always fully charge the batteries prior to your trip.
n Maintain 30–35 psi in pneumatic drive wheels.
n Plan your trip in advance to avoid inclines if possible.
n Limit baggage weight to essential items.
n Try to maintain an even speed and avoid stop-and-go driving.
What type of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. BothAGM and Gel-cell are deep-
cycle batteries that are similar in performance.
Use these specifications to reorder deep-cycle batteries:
Battery Specifications
Type:
Size:
Deep-cycleAGM or Gel-Cell
Group 24
Voltage:
Amperage:
12 volts each
70 or 80 amp hours
Size:
Voltage:
Amperage:
NF-22 (power seat option only)
12 volts each
45 - 55 amp hours
WARNING! Corrosive chemicals are contained in batteries. Use only AGM or gel-cell batteries to
reduce the risk of leakage or explosive conditions.
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium
batteries (nicads), or in other common battery types. Deep-cycle batteries are specifically designed to provide
power, drain down their charge, and then accept a relatively quick recharge. Sealed lead-acid batteries should be
charged as often as possible. They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your Jazzy’s specific demands.
Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries
encounter temperature extremes that may influence initial performance. Heat robs the charge from the battery, and
cold slows the power available and extends the time needed to recharge the battery (just as with a car battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature.
More importantly, it takes a few “charging cycles” (a partial drain—then a full recharge) to establish the critical
chemical balance that is essential to the battery’s peak performance and long life. It is well worth it to take the time
to break in your battery properly.
46
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
I X . B A T T E R I E S A N D C H A R G I N G
:
NOTE The useful life of a battery is quite often a reflection of the care it receives.
How can I ensure maximum battery life?
Afully charged, deep-cycle battery provides reliable performance and extended battery life. Keep your Jazzy’s
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged,
orstoredwithoutafullchargemaybepermanentlydamaged, causingunreliableJazzyoperationandlimitedbatterylife.
How should I store my Jazzy and its batteries?
If you do not use your Jazzy regularly, we recommend maintaining battery vitality by charging the batteries at least
once a week.
If you do not plan on using your Jazzy for an extended period, fully charge the batteries prior to storage. Discon-
nect the battery harnesses and store the Jazzy in a warm, dry environment.Avoid temperature extremes, such as
freezing and excessively hot conditions, and never attempt to charge a frozen battery.Acold or frozen battery
should be warmed for several days prior to recharging.
NOTE: If you are storing a Jazzy for an extended period of time, you may wish to block the unit up with
several boards under the frame. This keeps the tires off the ground and prevents the possibility of flat spots
developing in the tires.
What about public transportation?
If you intend to use public transportation while using your Jazzy, you must contact in advance the transportation
provider to determine their specific requirements. See II. “Safety” for more details.
Sealed lead-acid and gel cell batteries are designed for application in wheelchairs and in other mobility vehicles.
Generally, sealed lead-acid batteries are safe for all forms of transportation such as aircraft, buses, and trains. We
suggest that you contact your transportation provider to determine specific requirements of transportation and
packaging.
What about shipping?
If you wish to use a freight company to ship your Jazzy to your final destination, repack your Jazzy in the original
shipping container and ship the batteries in separate boxes.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
47
Download from Www.Somanuals.com. All Manuals Search And Download.
X . C A R E A N D M A I N T E N A N C E
ROUTINE MAINTENANCE
Your Jazzy is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks.You
can perform some of these checks, but others require assistance from an authorized Pride provider. Preventive
maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help
ensure that your Jazzy gives you years of trouble-free operation. If you have any doubt as to your Jazzy’s care or
operation, contact your authorized Pride provider.
Your Jazzy, like most electrical equipment, is susceptible to damage from the elements.Avoid damp areas of any kind.
CAUTION! Direct exposure to water or dampness could cause the power chair to malfunction
electronicallyandmechanically. Watercancauseelectricalcomponentstocorrodeandthechair’s
frame to rust.
Should your Jazzy come in contact with water:
1. Dry your Jazzy as thoroughly as possible with a dry towel.
2. Allow your Jazzy to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your Jazzy again.
4. If any inconsistencies are found, take your Jazzy to an authorized Pride provider.
TEMPERATURE
Some of the parts of your Jazzy are susceptible to extreme changes in temperature. Always keep your Jazzy
between the temperatures of 18° F/-8° C/ and 122° F/50° C.
n In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze de-
pends on a number of factors, such as battery charge, usage, and composition of the batteries (e.g., sealed
lead-acid or gel cell).
n Temperatures above 122° F/50° C may cause your Jazzy to operate at a reduced speed. This reduced speed
is a safety feature built into the controller that helps prevent damage to the motor and other electrical compo-
nents. See VIII. “Operation.”
GENERAL GUIDELINES
n Avoid knocking or bumping the controller, especially the joystick.
n Avoid prolonged exposure of your Jazzy to extreme conditions, such
as heat, cold, or moisture.
n Keep the controller clean.
n Check all controller connectors on the electronics tray to ensure that they
arealltightandsecuredproperly.Alsocheckthechargerharnessconnec-
tor.
n When the battery condition meter is completely lit, the batteries are
fully charged, and the controller and the electrical system are OK.
n If one red bar on the battery condition meter is blinking slowly, the
batteries are low and need to be charged, but the controller and the
electrical system are OK.
Figure 40. Check Tire Pressure
n If the battery condition meter is blinking rapidly, the controller has de-
tected a fault in either its own circuits or in your Jazzy’s circuits. See
VIII. “Operation.”
n Make sure the drive tires are inflated to 30 – 35 psi. See figure 40.
48
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
X . C A R E A N D M A I N T E N A N C E
WARNING! Overinflating tires can cause them to explode and can result in personal injury.
WARNING! Do not use high pressure hose to inflate your tires.
n Use a rubber conditioner on the tire sidewalls to help preserve them.
Never use a rubber conditioner on the tread area of the tires; doing so may make the tires slippery
and cause your Jazzy to skid.
n The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help
it retain its high-gloss appearance.
n Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within
the battery well, with the battery terminals facing inward, toward each other. Refer to the frame decal for the
correct wiring layout.
n All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
DAILY CHECKS
n With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the
center when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect
the boot. Do not handle or try to repair it. See your authorized Pride provider if there is a problem.
n Visually inspect the controller harnesses. Make sure that they are not frayed or cut or have any wires exposed.
See your authorized Pride provider if there is a problem with any of these harnesses.
WEEKLY CHECKS
n Disconnect and inspect the controller and the charger harnesses from the electronics tray. Look for corrosion.
Contact your authorized Pride provider if necessary.
n Ensure that all parts of the controller system are securely fastened to your Jazzy. Do not overtighten any screws.
n Check for proper tire inflation. There should be 30 – 35 psi in each tire. If a tire does not hold air, see an
authorized Pride provider for replacement of the tube.
n Calibrate the joystick if a noticeable difference in performance is detected or if the joystick does not operate
properly.You can do this for the Remote Plus, Pilot, and Europa controllers.
n Check the brakes. This test should be carried out on a level surface with at least three feet of clearance around
your Jazzy.
To check the brakes:
1. Turn on the controller and turn down the speed level of your Jazzy.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick.You
must be able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this
test three times, pushing the joystick backwards, then left, and then right.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
49
Download from Www.Somanuals.com. All Manuals Search And Download.
X . C A R E A N D M A I N T E N A N C E
To calibrate the joystick (Remote Plus only):
1. Position the joystick in the full reverse position and hold it there. Turn on the controller.
2. The battery condition meter lights up from one bar to ten bars, and then back to one bar. It does this twice, then
blinks rapidly.
3. Turn off the controller.
4. Position the joystick in the full forward position and hold it there; then turn the controller on.
5. The battery condition meter lights up from one bar to ten bars, and then back to one bar. It does this twice, then
blinks once, and then it blinks continuously.
6. Turn off the controller. Now the joystick and controller are set up to function properly together.
MONTHLY CHECKS
n Check that the anti-tip wheels do not rub the ground when you are operate the Jazzy.Adjust them as neces-
sary. See VI. “ComfortAdjustments.”
n Check for extreme wear on the anti-tip wheels. Replace them as necessary.
n Check for drive tire wear. See an authorized Pride provider for repair.
n Check the rear casters for wear. Replace them as necessary.
n Check the rear forks for damage or fluttering which indicates that they may need to be adjusted or have the
bearings replaced. See an authorized Pride provider for repair.
n Keep your Jazzy clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
YEARLY CHECKS
Take your Jazzy to an authorized Pride provider for yearly maintenance. This helps ensure that your Jazzy is
functioning properly and helps prevent future complications.
STORAGE
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the
batteries from the Jazzy. See IX. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
CLEANING INSTRUCTIONS
CAUTION! Never hose off your Jazzy or place it in direct contact with water. Your Jazzy has a
painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp cloth.
CAUTION! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
TIRES AND TUBES
If your Jazzy is equipped with pneumatic tires, you should check the air pressure at least once a week. This
prolongs the life of your tires and helps ensure the perfect operation of your chair. If you have a flat tire, replace the
tube. Replacement tires and tubes are readily available through the provider where you purchased your Jazzy.
50
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
X . C A R E A N D M A I N T E N A N C E
WARNING! To avoid possible injury, be sure that the
controller’s power is turned off and the power chair is not
in freewheel mode before performing this procedure.
WARNING! Completely deflate the tire before attempting
repair.
Follow these easy steps for a quick and safe repair:
1. Completely deflate the tire if pneumatic.
2. Use a 3/4-in. socket wrench to remove the drive wheel nut from
the center hub of the wheel. See figure 41.
3. Pull the wheel off of the axle.
DRIVE
WHEELNUT
4. Remove the bolts that hold the wheel halves together.
5. Remove the old tube and/or tire and replace it with a new tube
and/or tire.
Figure 41. Drive Wheel
6. Reassemble the wheel.
7. Slide the wheel back onto the shaft.
8. Install the drive wheel bolt into the center hub and tighten.
9. Inflate the tire to 30 – 35 psi.
BATTERY REPLACEMENT
To replace the battery:
Adiagram is printed on a decal on the Jazzy 1122 frame near the
battery tray. See figure 42.
1. Remove 1/4-in.detent pin from the bottom of the foot frame.
2. Lift the foot frame straight up to remove it from the mounting
bracket.
3. Locate the two wiring harnesses that will be attached to your
batteries.
4. Disconnect these two harnesses from their respective quick
disconnects by pulling the quick disconnects toward you.
5. Remove batteries from the power base assembly.
Figure 42. Battery Connections
6. Disconnectthebatteryharnessesfromthepositiveandnegativeterminals.
7. Replace old batteries with new ones.
8. Connect the wire labeled BAT (+) to a battery’s positive (red) terminal. Connect the wire labeled BAT(-) to the
negative (black) terminal. Install the battery in the rear of your Jazzy’s battery tray with the battery’s terminals
facing inward, toward the center of the Jazzy. Plug the wiring harness into a quick disconnect.
9. Connect the wire labeled BAT(+) to the other battery’s positive (red) terminal. Connect the wire labeled BAT
(-) to the negative (black) terminal. Install the battery in the front of your Jazzy’s battery tray with the battery’s
terminals facing inward, toward the center of the Jazzy. Plug the wiring harness into a quick disconnect.
WARNING! Make sure you tighten the fasteners so that the connections are secure.
10. Replace the foot frame using the 5/16-in. detent pin to secure.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
51
Download from Www.Somanuals.com. All Manuals Search And Download.
X . C A R E A N D M A I N T E N A N C E
MOTOR BRUSHES
The electric motors that power your Jazzy use carbon brushes. These
brushes may become susceptible to wear over a long period of
time. The motor brushes are the two contacts located inside the
motor assembly that supply power to the motor. They are designed
to provide several thousand hours of operation. However, if the
brushes become dirty with carbon deposits or wear out, the motor
will run poorly or not at all. We recommend that your authorized
Pride provider inspect the brushes every six months or sooner if
your Jazzy runs poorly.
MOTOR BRUSH CAP
Figure 43. Motor
WARNING! If inspection determines excessive wear on the brushes, they must be replaced or
motor damage will result. Failure to maintain the brushes could void your warranty.
To inspect or replace the motor brushes:
1. Remove the seat, body shroud, and batteries. See VII. “Disassembly.”
2. Unscrew the motor brush caps. See figure 43.
3. Remove the brushes.
4. Inspect for wear.
5. Replace brushes, if necessary. Contact your authorized Pride provider for replacement brushes.
CORRECTIVE MAINTENANCE
If the battery condition meter does not light up when you turn on the power:
n Check the harness connections. Make sure they are tight.
n Check the circuit breaker. Reset it if necessary.
n Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are
\
available at automotive parts stores. Disconnect both batteries before load testing and follow the directions that
come with the load tester. If either one of the batteries fails the load test, replace both of them. If your Jazzy still
does not power up, contact your authorized Pride provider.
WHEN TO SEE YOUR AUTHORIZED PRIDE PROVIDER FOR SERVICE
The following symptoms could indicate a serious problem with your Jazzy. If necessary, contact your authorized Pride
provider.When calling, have the model number, serialnumber, nature of the problem, and the trouble code if available.
n Motor noise
n Frayed harnesses
n Cracked or broken connectors
n Uneven wear on any of the tires
n Jerky motion
n Pulling to one side
n Bent or broken wheel assemblies
n Does not power up
n Powers up, but does not move
52
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
X I . O P T I O N A L A C C E S S O R I E S
The following accessories are available from your authorized Pride provider.
POSITIONING BELT
The positioning belt is designed to support the operator so that he or she does not slide down or forward in the
seat. The positioning belt is not designed for use as a restraining device. Make sure the belt is secure but does not
cause discomfort.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle.
Nor is your Jazzy suitable for use as a seat in any vehicle. Anyone traveling in a vehicle
should be properly belted into seats approved by the vehicle manufacturer.
OXYGEN TANK HOLDER
The removable oxygen tank holder is mounted to the back of the seat by means of the accessory bracket.
CANE AND CRUTCH HOLDER
The removable cane and crutch holder is mounted to the back of the seat by means of the accessory bracket.
WALKER HOLDER
The removable walker holder is mounted to the back of the seat by means of the accessory bracket. It can hold
a standard size walker.
REAR BASKET
The rear basket is mounted to the accessory bracket. It has a handle that you can use when you remove the basket
from your Jazzy.
CUP HOLDER
The cup holder is mounted to the armrest.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
53
Download from Www.Somanuals.com. All Manuals Search And Download.
X I I . W A R R A N T Y
LIFETIME LIMITED WARRANTY
For the lifetime of your Jazzy, from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by anauthorized representative of
Pride to be defective in material and/or workmanship:
n Structural frame components
TWO-YEAR WARRANTY
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
n Electronics
EIGHTEEN-MONTH WARRANTY
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of
Pride to be defective in material and/or workmanship:
n Motor/gearbox assembly
WARRANTY EXCEPTIONS
Motor: If damage occurs to the commutator of a motor as a result of not replacing the motor brushes after heavy
wear to brushes. Motor brushes are wear items and are not warranted.
Brake: One-year warranty for electrical function of the brake. Brake pads are a wear item and are not warranted.
SIX-MONTH LIMITED WARRANTY
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser,
free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
n Plastic components, except body
n Rubber components (except tires and tubes)
n Bearings and bushings
n Casters and anti-tip wheels
Battery warranty is covered by the battery manufacturer. Battery warranty is not covered by Pride.
54
WWW.PRIDEMOBILITY.COM
JAZZY 1122/REV D/FEB 03
Download from Www.Somanuals.com. All Manuals Search And Download.
X I I . W A R R A N T Y
Warranty service can be performed by an authorized Pride provider or by Pride. Do not return faulty parts to Pride
without prior consent.All transportation costs and shipping damage incurred while submitting parts for repair or
replacement are the responsibility of the original purchaser.
WARRANTY EXCLUSIONS
n ABS plastic body shrouds and footrest covers are wear items and are not warranted
n Batteries (battery manufacturer provides a six-month limited warranty)
n Tires and tubes
n Upholstery and seating
n Repairs and/or modifications made to any part without specific prior written consent from Pride
n Circumstances beyond the control of Pride
n Labor, service calls, shipping, and other charges incurred for repair of the product unless specifically autho-
rized by Pride
Damage caused by:
n Battery fluid spillage or leakage
n Abuse, misuse, accident, or negligence
n Improper operation, maintenance, or storage
n Commercial use, or use other than normal
There is no other express warranty.
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1)
year from the date of purchase and to the extent permitted by law.Any and all implied warranties are excluded.
This is the exclusive remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of
limitation of incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please fill out and return the product registration card to Pride. This aids Pride in providing the best possible
technical and customer service.
JAZZY 1122/REV D/FEB 03
WWW.PRIDEMOBILITY.COM
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Quality Control - Model 1122
Thank you for making the Pride Jazzy your choice in power chairs.
We have thoroughly inspected your Jazzy. The following checkmarks indicate that it has been test
driven and inspected.
Controller
Model #______________
Controller Serial #
Serial #______________
Joystick Serial #
Inclusion of all Parts
Fit and Finish
Performance
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
Download from Www.Somanuals.com. All Manuals Search And Download.
|