INSTALLATION INSTRUCTIONS
Rotary Flat Mount
Model: RFM
AUSTRALIA, NEW ZEALAND, OCEANIA
EUROPE
Swallow House,
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
(DISTRIBUTOR)
P.O. Box 295
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Mordialloc Victoria 3195
Australia
Phone: 039586 6330
Phone: 800-368-9700
Fax: 800-832-4888
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2008
9531-009-041-03
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
Parts List
This mount is shipped with all installation hardware and components. Make sure that none of these parts are
missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop and
contact Premier Mounts (800) 368-9700.
Universal Mounting Brackets (Qty 2)
Rotating Universal Bracket Bar (Qty 1)
5/16” x 3” Lag Bolts - wooden studs
only (Qty 6)
5/16” Flat Washers
(Qty 6)
M6 Knurl Knob
(Qty 1)
Griplate™ (Qty 8)
Installation Tools
Phillips Head Screw Driver
Pencil
Soft Material/Blanket
Tape Measure
1/2” Socket and Wrench
Drill Gun
Level (Supplied)
M5 Allen Wrench (Supplied)
5/32” Allen Wrench (Supplied)
1/4” Drill Bit (Pilot Holes)
Thread Depth Indicator (Supplied)
Masonry Drill Bit (Concrete Applications - Commercially Available)
Installation Instructions
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
(Qty 8)
(Qty 8)
M4 x 16
M4 x 25
M6 x 20
(Qty 8)
(Qty 8)
M6 x 30
M6 x 45
(Qty 8)
M5 x 12
M5 x 16
(Qty 8)
(Qty 8)
M8 x 20
M8 x 25
(Qty 8)
(Qty 8)
M5 x 20
M5 x 25
M5 x 50
(Qty 8)
(Qty 8)
(Qty 8)
M8 x 30
(Qty 8)
(Qty 8)
M6 x 16
(Qty 8)
M8 x 35
M8 x 45
(Qty 8)
M8 x 70
(Qty 4)
Page 4
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
The nylon spacers may be stacked to achieve proper spacing.
9/16" Nylon spacers
(Qty 8)
1/4" Nylon spacers
(large)
(Qty 8)
1/2" Nylon spacers
(large)
Nylon sleeves
(Qty 8)
(Qty 12)
5/16" Flat washers
(metal)
(Qty 8)
1" Nylon Spacers
(Qty 8)
1/4" Nylon spacers
(small)
(Qty 8)
Installation Instructions
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
Thread Depth Indicator
1. Insert the thread depth indicator (supplied) through the thread inserts found on the back of the flat panel to make sure the inserts
measure the same full depth and mark it (Figure 1).
2. Locate the correct diameter screw for the thread insert. Compare your marking to the screws (supplied).
3. If your selected screw is longer than the marking on the thread depth indicator, DO NOT USE this screw.
4. The screw length must not bypass the marking. Select another screw size (Figure 2 and 3), until you find one that comes closest to
your mark without going past.
Inverted Flat
Panel Display
Marking the
Depth
Thread Insert
Thread Depth
Indicator
Screw
Screw
Marking
Marking
Thread Depth
Indicator
Thread Depth
Indicator
Page 6
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
Mount Installation
Step 1
Step 2
Step 3
Determine where the mount lo-
cation will be. Use a stud finder
to locate the nearest wall stud.
Once the stud has been located, use a pencil
to mark the spot.
Using a 1/4” drill bit, drill the upper mount-
ing hole where the mark was made.
For ease of installation, it is recommended that two people perform the installation. One person should hold the
mount while the other person installs the lag bolt and washer. Making sure that the mount is level, the person not
holding the mount must mark and drill the second mounting hole and secure the second lag bolt and washer.
Step 6
Step 5
Step 4
Insert two (2) 5/16” x 3” lag bolts
and washers into the mounting holes
and tighten (see WARNING: below
Place a level (supplied) on the top
rail and make sure that the mount is
level. Once the mount is level, Drill
pilot holes in the lower mounting
slots and install two (2) 5/16” x 3”
lag bolts and washers into the mount-
ing holes and tighten.
After the holes have been pre-drilled,
line up the mounting slot openings
with the pre-drilled holes.
Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal
injury or damage to property.
If the studs are 12” (304.8mm) apart, use three (3) 3” (76.2mm) lag bolts for the top rail and three (3) 3” (76.2mm)
lag bolts for the lower rail. If the studs are 16”(406.4mm), 18” (457.2mm) or 24” (609.6mm) apart, use two (2) 3”
lag bolts for the top rail and two (2) 3” lag bolts for the lower rail.
Installation Instructions
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
Concrete Mounting
Concrete anchors must be used for concrete installation. They can be purchased at your local hardware store. The
mounting surface must be a minimum 6” thick.
1.
2.
3.
4.
5.
6.
7.
8.
Begin by placing the mount into position against the wall, keeping it level.
Mark off four holes to be used for securing the mount.
Next, drill holes using a masonry bit for your anchors (recommended masonry bit).
Insert a commercially available concrete anchor into each hole (recommended 3/8” wedge anchors).
If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the wall.
Once all of the anchors are in place, move the wall bracket into position.
Attach the nut onto the threaded shaft that is protruding from the wall.
Do not tighten until all nuts are in place.
Universal Mounting Bracket Assembly
1.
2.
Place the universal bracket bar and the universal brackets on a flat surface.
Slide the universal brackets onto the universal bracket bar (as shown below) with the set screws facing up. At this
time, do not tighten the set screws that are located on the universal bracket.
3.
4.
Place the display on a soft, flat surface, face-down. Next, place the universal bracket assembly on the back of the
display, with the universal brackets resting directly over the display mounting points.
Once the desired position has been determined, place the Griplate™ washers over each mounting point and secure
them using the appropriate hardware (see Page 5).
For the two upper mounting points, the Griplate™ flat side must be facing up. For the two lower mounting points, the
Griplate™ flat side must be facing down.
5.
At this time, center the universal bracket bar and tighten the set screws that are located on the universal brackets.
M8
M5
Universal Mounting Brackets
M6
M4
Set Screw
Universal Bracket Bar
Griplate™
Griplate™
IT WILL TAKE TWO PEOPLE TO COMPLETE THE NEXT INSTALLATION STEP.
Page 8
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
6.
Lower the universal bracket bar with attached
display into the cradle (as shown to the left).
Nylon
Sleeve
After loosening the tension bolts, be sure that the
nose piece is held together tightly before rotating.
Knurl Knob Mounting Point/M6 x 12mm Security Head and
M6 Lock Washer Mounting Point.
7.
Insert an M6 Knurl Knob/M6 x 12mm Security
Head and M6 Lock Washer into the knurl knob/
security screw mounting point and tighten.
To access the knurl knob/security screw
location while the display is attached, the
RFM must be rotated to the “portrait”
position (vertical position
8.
Tighten the two (2) Phillips head screws (located
on the side of the mounting block) once the final
position is attained.
Installation Instructions
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
Display Orientation
The RFM will allow the user to adjust the display a full 360°.
BEFORE ROTATING THE RFM, MAKE SURE THAT THE M6 KNURL KNOB IS SECURELY FASTENED
TO THE RFM. ALSO, PLEASE MAKE SURE YOU ALLOW ENOUGH CABLE AND WIRE CLEARANCE
FOR FULL ROTATION.
M6 Knurl Knob
1.
To adjust the RFM, rotate the display either
clockwise or counter-clockwise.
2.
Tighten
the
two
Phillips
head locking screws (see Step 8,
Page 10).
Technical Specifications
All measurements are in inches (mm).
Page 10
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
RFM
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS,
DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN
WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE
OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, IN-
CLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE. PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LA-
BOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-
sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the
problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier
Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 E. Miraloma Avenue
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
Installation Instructions
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
|