Premier Mounts Projector Accessories PBM 070L User Manual

INSTALLATION INSTRUCTIONS  
PBM-070L  
AUSTRALIA, NEW ZEALAND, OCEANIA  
NORTH AMERICA  
3130 East Miraloma Avenue  
EUROPE  
Swallow House,  
(DISTRIBUTOR)  
P.O. Box 295  
Anaheim, CA 92806 USA  
USA and Canada –  
Phone: 800-368-9700  
Shilton Industrial Estate,  
Shilton, Coventry, England CV79JY  
Phone: +44 (0) 2476 614700  
Fax: +44 (0) 2476 614710  
Mordialloc Victoria 3195  
Australia  
Phone: 039586 6330  
Fax: 800-832-4888  
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044  
©Premier Mounts 2008  
9530-007-003-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PBM-070L  
Parts List  
This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are  
missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the  
installation and contact Premier Mounts 800-368-9700.  
Base Box (Qty 1)  
Projector Bracket(Qty 1)  
Jam Nut (Qty 1)  
M6 x 6mm Set Screw (Qty 1)  
Nylon Spacers (Qty 2)  
¼” Flat Washers (Qty 2)  
M6 x 12mm Phillips Head Screws (Qty 6)  
Projector Bracket Hardware  
M8 x 12mm Phillips Head Screws (Qty 8)  
Installation Tools  
Soft Material/Blanket  
Pencil  
Portable Drill  
Finder (Commercially Available)  
Phillips Head Screw Driver  
M3 Allen Wrench (Supplied)  
Level  
Ladder  
Tape Measure  
Installation Manual  
Page - 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PBM-070L  
Projector Bracket Installation  
M8 x12mm Phillips  
Head Screws  
Projector Bracket  
M8 x12mm Phillips  
Head Screws  
Screwdriver  
Projector  
Step 1. Invert the projector and place it on a soft and flat surface. Step 1. Using a screwdriver, secure the mounting bracket using  
Remove any foot levelers that might possibly prevent the  
correct installation of the bracket.  
Step 2. Locate the eight mounting points located on the bottom of  
the projector.  
Step 3. Line up the mounting points on the projector with the  
mounting holes on the mounting bracket.  
eight (8) M8 x 12mm Phillips Head screws.  
Do not over-tighten these screws. Over-tightening  
the screws may result in damaging the threaded  
inserts on the projector.  
Installation Manual  
Page - 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PBM-070L  
Ceiling Installation  
Step 1. Separate the top bridge from the base box by removing the six (6) M6 x 12 mm screws that are located on the base box, three  
on each side (A).  
Step 2. Secure the top bridge to the ceiling structure at this time (see warning label) using commercially available hardware (B).  
Step 3. Use the two (2) middle slot openings for single wood stud mounting. All other mounting points on the top bridge may be  
used depending on your installation application (B).  
Step 4. Replace the base box to the secured top bridge and secure with the six M6 x 12 mm screws (C).  
A
B
Ceiling Structure  
Wood Stud  
Top Bridge  
Lag Bolts  
(Commercially Available)  
C
Base Box  
Installation Manual  
Page - 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PBM-070L  
Step 5. Loosely install the hinge pin screws, flat washer and nylon spacer to each side of the base box.  
Step 6. Slide the nylon spacer and the flat washer to the back of the screws.  
Step 7. Raise the mounting bracket and attached projector to the base box and insert the hinge-pins through the hinge-pin openings.  
Step 8. Tighten the hinge pin screws.  
Step 9. Determine the viewing angle. Once the viewing angle has been determined, insert and tighten the four (4) tilt locking  
screws.  
Do not over-tighten the screws.  
Ceiling Structure  
Wood Stud  
Top Bridge  
Tilt Locking  
Screws  
Hinge Pin Bolt  
Flat Washer  
Page - 6 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PBM-070L  
If installing a PBM-070L from the ceiling structure, please refer to the installation instructions that are included with  
those mounts.  
Step 10. Install the jam screw all the way up to the end of the threads of the threaded PBM-070L.  
Step 11. Screw in the 1½" bridge opening to the PBM-070L all the way up to the jam screw.  
Step 12. Tighten the jam screw and the base box together.  
Step 13. Loosely install the hinge pin screws, flat washer and conical spacer to each side of the base box.  
Step 14. Slide the conical spacer and the flat washer to the back of the screws.  
Step 15. Raise the projector mount, attached to the projector’s chassis, and insert the hinge-pins through the hinge-pin openings.  
Step 16. Raise the rear of the projector and install the four (4) M6 x 12 mm tilt locking screws to the rear of the base box; adjust the  
tilt and lock it.  
Step 17. Tighten the two (2) M6 x 12 mm hinge pin screws.  
Step 18. At this time, use the M3 Allen wrench to tighten the M6 x 6mm set screw.  
Projector Adjustment  
Step 1. You can adjust the roll of the projector by loosening the three (3) front and rear M6 x 12mm screws.  
Do not over-tighten the screws.  
Step 2. Set the desired roll and then tighten the screws. First tighten the center screws and work your way to the outside screws,  
making any final adjustments prior to tightening the last two screws.  
Step 3. You can adjust the tilt of the projector by loosening the four (4) M6 x 12mm screws (two on each side of the base box).  
Step 4. Set the desired tilt and then tighten the screws, making any final adjustments prior to tightening the last two screws.  
Step 5. Once all adjustments have been made, tighten all hardware.  
AST-2446,  
AST-1321 or  
1
2" Pipe  
M6 Set Screw  
Tilt  
Locking Screws  
Roll Adjustment  
Screws  
Hinge Pin Screw  
Flat Washer  
Nylon Spacer  
Page - 7 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PBM-070L  
Technical Specifications  
All measurements are inches (mm).  
All base boxes feature the following adjustments to facilitate ease of installation:  
A.  
B.  
C.  
D.  
Tilt of ±6° from center  
Roll of ±3° from center  
Yaw of ±360° when used with 1 ½" or 1" mount threaded pipe  
Direct mating with standard 1 ½" and 1" mount threaded pipe  
Page - 8 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PBM-070L  
Warranty  
PREMIER MOUNTS  
LIMITED LIFETIME WARRANTY  
What and Who is Covered by this Limited Warranty and for How Long  
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of  
the original installation of this product. The limited warranty is valid only for the original purchaser of the  
product.  
What Premier Mounts Will Do  
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is  
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will  
be shipped to you at no charge, but you must pay any labor costs.  
What is Not Covered; Limitations  
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS,  
DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN  
WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE  
OF ITS PRODUCTS.  
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,  
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE. PREMIER MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR  
CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS  
PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS  
OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF  
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR  
EXCLUSION MAY NOT APPLY TO YOU.  
What Customers Must Do for Limited Warranty Service  
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to  
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original  
consumer purchaser must accompany all warranty claims. Warranty claims must also include a description of  
the problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to  
Premier Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or  
by fax.  
Premier Mounts  
Attn: Warranty Claim  
3130 E. Miraloma Avenue  
Anaheim, CA 92806  
How State Law Applies  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE  
OTHER RIGHTS WHICH VARY FROM STATE TO STATE.  
Installation Manual  
Page - 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Car Stereo System FC 931 User Manual
Philips Car Video System 190TW9FB User Manual
Philips Cassette Player AW 7590 User Manual
Philips Electric Shaver T870 User Manual
Philips Headphones SHE2634 User Manual
Philips Indoor Furnishings SBC VS010 User Manual
Philips Work Light Solution Series User Manual
Pioneer Indoor Furnishings PDK TS01 L User Manual
Pioneer Portable Speaker EX Series User Manual
Pioneer Universal Remote BR 95 User Manual