This .pdf document is bookmarked
Operating Instructions and Parts Manual
Straight Line Rip Saw
Model SLR12
Powermatic
427 New Sanford Road
LaVergne, TN 37086
Ph.: 800-274-6848
Part No. M-0460276
Revision F2 04/2014
Copyright © 2014 Powermatic
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Warranty and Service ..............................................................................................................................2
Table of Contents....................................................................................................................................3
Warning...................................................................................................................................................4
Introduction .............................................................................................................................................6
Specifications..........................................................................................................................................6
Features..................................................................................................................................................7
Receiving ................................................................................................................................................8
Installation...............................................................................................................................................8
Control Box..........................................................................................................................................9
Grounding Instructions.........................................................................................................................9
Operating Controls...............................................................................................................................9
Installing/Changing Blade...................................................................................................................10
Mounting the Fence ...........................................................................................................................10
Adjustments ..........................................................................................................................................11
Main Belt Tension ..............................................................................................................................11
Gearbox Belt Tension ........................................................................................................................11
Feed Speed .......................................................................................................................................12
Fence Alignment................................................................................................................................12
Adjusting Blade and Roller Height......................................................................................................12
Oiler Adjustment ................................................................................................................................13
Operation ..............................................................................................................................................13
Feeding Curved Wood .......................................................................................................................13
Maintenance..........................................................................................................................................14
Optional Accessory................................................................................................................................14
Troubleshooting (Electrical) ...................................................................................................................14
Troubleshooting (Mechanical)................................................................................................................15
Replacement Parts................................................................................................................................15
Parts List: Infeed Body Assembly.......................................................................................................16
Infeed Body Assembly .......................................................................................................................17
Parts List: Arbor Spindle Assembly.....................................................................................................18
Arbor Spindle Assembly.....................................................................................................................19
Parts List: Motor and Drive Unit Assembly..........................................................................................20
Motor and Drive Unit Assembly ..........................................................................................................21
Parts List: Laser Assembly (Optional Accessory)................................................................................22
Parts List: Roller and Frame Assembly...............................................................................................23
Roller and Frame Assembly ...............................................................................................................25
Parts List: Table and Stand Assembly................................................................................................26
Table and Stand Assembly.................................................................................................................28
Parts List: Electrical Control Panel (SLR12-443).................................................................................29
Electrical Connections – 3 Phase, 230V, 60Hz.......................................................................................30
Electrical Connections – 3 Phase, 460V, 60Hz.......................................................................................31
Preventive Maintenance ........................................................................................................................32
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
1. Read and understand the entire owner’s manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This rip saw is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a rip saw, do not use until proper training
and knowledge have been obtained.
5. Do not use this rip saw for other than its intended use. If used for other purposes, Powermatic
disclaims any real or implied warranty and holds itself harmless from any injury that may result from
that use. Your rip saw is provided with a 15HP main motor; do not equip your rip saw with a motor of
higher horsepower.
6. Always wear approved safety glasses/face shields while using this rip saw. Everyday eyeglasses only
have impact resistant lenses; they are not safety glasses.
7. Before operating the rip saw, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Keep hands outside the machine. Never reach under the guards to try to clear stock that stops
feeding.
9. Wear ear protectors (plugs or muffs) during extended periods of operation.
10. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
•
•
•
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
11. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
12. Make certain the switch is in the OFF position before connecting the machine to the power supply.
13. Make certain the machine is properly grounded.
14. Make all machine adjustments or maintenance with the machine unplugged from the power source. A
machine under repair should be red tagged to show that it should not be used until maintenance is
complete.
15. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
16. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
18. Provide for adequate space surrounding work area and non-glare, overhead lighting.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Keep the floor around the machine clean and free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work area. Keep children away.
21. Make your workshop child proof with padlocks, master switches or by removing starter keys.
22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
23. Maintain a balanced stance at all times so that you do not fall or lean against moving parts. Do not
overreach or use excessive force to perform any machine operation.
24. Be sure the blade rotates under power in a counterclockwise direction when viewed from the front of
rip saw (see page 7 for orientation of machine sides).
25. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
26. Use recommended accessories; improper accessories may be hazardous.
27. Maintain tools with care. Keep blades sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
28. Turn off the machine and disconnect from power before cleaning. Use a brush or compressed air to
remove chips or debris — do not use your hands.
29. Do not stand on the machine. Serious injury could occur if the machine tips over.
30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
31. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
- - SAVE THESE INSTRUCTIONS - -
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This manual is provided by Powermatic covering the safe operation and maintenance procedures for a
Powermatic Model SLR12 Rip Saw. This manual contains instructions on installation, safety precautions,
general operating procedures, maintenance instructions and parts breakdown. This machine has been
designed and constructed to provide years of trouble free operation if used in accordance with
instructions set forth in this manual. If there are any questions or comments, please contact either your
Specifications
Stock number...............................................................................................................................1791285
Main motor ....................................................................................15HP, 3Ph, 230/460V (pre-wired 230V)
Feed motor......................................................................................2HP, 3Ph, 230/460V (pre-wired 230V)
Controls..............................................................................................................................220V Magnetic
Blade speed ..............................................................................................................................4500 RPM
Feed speeds ...............................................................................................................30-90 FPM variable
Arbor size.............................................................................................................................. 1" (25.4 mm)
Provided Blade size...............................................................................Dia. 12" (305 mm) x 4.0mm x 48T
Cutting depth......................................................................................................................3-7/8" (98 mm)
Maximum ripping width.........................................................................................................18" (460 mm)
Pressure rollers ....................................................................................................................................... 5
Anti-kickback devices .............................................................................................................................. 2
V-belts..................................................................................................................................................... 4
Table size................................................................................................. 35" x 55" (890 mm x 1397 mm)
Table height ......................................................................................................................... 32" (813 mm)
Dust Collection Port................................................................................................................4" (102 mm)
Minimum CFM required ....................................................................................................................... 600
Shipping weight...........................................................................................................................2530 lbs.
Net weight ...................................................................................................................................2090 lbs.
Overall dimensions (L x W x H)...................................................62" x 56" x 41" (1575 x 1422 x 1041 mm)
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Powermatic reserves the right to change specifications at any time and without
prior notice, without incurring obligations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Figure 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving
Open shipping container and check for shipping
damage. Report any damage immediately to
your distributor and shipping agent. Do not
discard any shipping material until the Rip Saw
is installed and running properly.
Compare the contents of your container with the
following parts list to make sure all parts are
intact. Missing parts, if any, should be reported
to your distributor. Read the instruction manual
thoroughly for assembly, maintenance and
safety instructions.
Contents of crate:
1 Rip saw body
1 Rip fence
1 Blade
1 Toolbox containing (shown in Figure 2):
A – 1 grease gun
B – 1 set open-end wrenches
C – 1 set hex wrenches
D – 4 cast iron foot pads
E – 4 M16x80 leveling screws
E – 4 M16 hex nuts
F – 1 arbor wrench
Figure 2
G – 1 T-wrench
1 Instruction manual
1 Warranty card
Installation
Tools required for assembly:
forklift or hoist, with slings
open-end wrenches (provided)
hex wrenches (provided)
arbor wrench (provided)
T-wrench (provided)
NOTE: The terms “front”, “back”, “infeed side”
and “outfeed side” are explained on page 7.
1. Lift the machine with a hoist or forklift, using
slings through the lifting eyes on the
machine. Make sure the capacity of the
lifting unit is sufficient to lift this size
machine.
2. The rip saw should be located in an area
that is well-lit, with a sturdy, level floor and
enough space for loading and off-loading
stock and general servicing of the machine.
3. The rip saw can be bolted to the floor
through the holes at the four corners. If it will
not be bolted to the floor, the four cast iron
foot pads should be placed beneath the
corners, with the four M16 x 80 leveling
screws and four M16 nuts. See Figure 3.
Figure 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Place a level upon the machine table, and
adjust the screws over the foot pads as
necessary. When the machine is level,
tighten all four hex nuts against the
machine’s base.
Unpainted surfaces, such as the work table and
fence, have been given a protective coating at
the factory. This should be removed with a soft
rag moistened with a good commercial solvent.
Do not use acetone, lacquer thinner, gasoline or
any flammable solvents. Do not use an abrasive
pad.
Control Box
Swing out the control box (Figure 4). Use the set
screws to control the tightness of the mounting
arm.
Grounding Instructions
Figure 4
Electrical connections must
be made by
a
qualified electrician in
compliance with state and local codes. The
machine must be properly grounded to help
prevent electrical shock and possible death.
A power plug is not provided with the SLR12.
You may either connect one, or "hard-wire" the
saw directly to your electrical panel provided
there is a disconnect near the machine for the
operator. Consult electrical schematic on pages
30 and 31 for further clarification of wiring setup.
This machine must be grounded. Grounding
provides a path of least resistance to help divert
current away from the operator in case of
electrical malfunction.
Make sure the voltage of your power supply
matches the specifications on the motor plate of
the machine.
Figure 5
Operating Controls
The buttons on the control panel are explained
in Figure 5. After making electrical connections,
the machine should be turned on to verify the
direction of rotation. The blade arbor should
rotate counterclockwise when viewed from front
of machine (Figure 6). If rotation is wrong, turn
off the machine, disconnect power and switch
any two of the three electrical leads.
IMPORTANT: The emergency stop button
(Figure 5) shuts down all operations on the
machine simultaneously. To release the
emergency stop button, twist it clockwise.
Figure 6
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing/Changing Blade
1. Disconnect machine from power source.
2. Unscrew knurled knob on blade guard and
swing guard away, as shown in Figure 8.
3. Loosen the arbor lock lever (A, Figure 7)
and raise the arbor with the handwheel (B,
Figure 7) until the blade can slip on to the
arbor without interference from the
caterpillar.
4. Place the arbor wrench on the flat of the
arbor shaft. Place the T-wrench on the
screw head as shown (Figure 8). Hold the
shaft stationary with the arbor wrench while
loosening the screw.
Figure 7
5. Remove screw and flange and install new
blade, making sure to orient it properly - the
teeth at bottom of blade should face toward
infeed side of machine (as shown in Figure
6).
6. Replace flange and screw, and tighten
screw with the T-wrench while holding the
arbor wrench stationary.
7. Lower the blade down into the inserts on the
caterpillar track (blade teeth should be
0.5mm to 1.5mm lower than caterpillar
surface).
Figure 8
The blade teeth should not
contact the bottom of the inserts.
8. Close blade guard and tighten knurled knob.
Mounting the Fence
1. Slide the fence casting onto the end of the
guide bar while pulling back the main lock
handle (Figure 9).
2. The fence is moved along the guide bar by
rotating the handwheel. Use the main lock
handle to secure the fence casting in place.
3. Loosen the other lock handle and slide the
aluminum fence onto the casting. Tighten
the handle.
Figure 9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Main Belt Tension
1. Disconnect machine from power source.
2. Open back panels to expose the motor,
pulleys and belts, as shown in Figure 10.
Loosen hex nut (Fig. 11) and turn the
adjustment screw as needed to adjust the
tension. Proper tension is achieved when
there is a small amount of deflection by
using moderate finger pressure on the belt
midway between the pulleys.
3. Tighten hex nut (Fig. 11) and replace
panels.
Figure 10
Figure 11
Gearbox Belt Tension
1. Disconnect machine from power source.
2. Open lower back panel and loosen nuts on
the motor base (Fig. 12). Adjust motor base
up or down as needed, then tighten nuts.
Proper tension is achieved when there is a
small amount of deflection by using finger
pressure on the belt midway between the
pulleys.
3. Replace panels.
Figure 12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Feed Speed
The feed speed adjuster is found below the
gearbox (Figure 13). Feed speed should be
adjusted while the machine is running and the
caterpillar is in motion.
Turn adjuster clockwise to decrease feed speed,
counterclockwise to increase.
Fence Alignment
For accurate cutting, the fence must be parallel
to the line of cut:
Figure 13
1. Place a straight edge against the fence with
its other side flush to the blade, and check
that the fence is in line with the blade.
2. If adjustment is needed, loosen the socket
head cap screws on one end of the bar
(Figure 14). Move the bar in or out as
needed until fence is in line with blade.
3. Retighten screws.
Adjusting Blade and Roller Height
Figure 14
The small handwheel (A, Figure 15) raises or
lowers the blade. This blade setting is then
locked by tightening the lever (B, Figure 15).
The large handwheel (C, Figure 15) raises and
lowers the entire head including the pressure
rollers. The roller setting is then locked by
tightening the lever (D, Figure 15). A scale near
the lever displays the height.
The maximum travel of the blade can be
adjusted; for example, if a blade smaller than
12” is installed. To adjust:
1. Remove the back panels.
Figure 15
2. Loosen the socket head cap screw on the
stop mechanism (Figure 16).
3. Rotate the stop mechanism as needed to
allow more blade drop.
4. When finished adjusting, re-tighten socket
head cap screw, and install back panels.
Figure 16
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Oiler Adjustment
1. Remove plastic cover.
2. Loosen set screw (Figure 17) and rotate
knurled dial clockwise to increase oil output;
counter-clockwise to decrease oil output.
The scale is in cubic centimeters.
3. Retighten set screw, and install plastic
cover.
Operation
1. Check the oil tank at the infeed side of the
machine (Figure 18). If it is not full, remove
the cap and add light 20-weight oil through
the fill hole. Replace cap when finished.
Figure 17
IMPORTANT: The lubricator has a safety device
to ensure a longer service life. If the oil is below
minimum level, the device will automatically shut
off machine operations. The operator must fill
the oil tank in order to re-start the machine. Use
light 20-weight oil.
2. Set the head (rollers) at the proper height
for the stock being used, and make sure the
blade is approximately 0.5 to 1.5mm below
the caterpillar surface.
3. Start the saw blade. Let it run for about 10
seconds and then start the caterpillar. Verify
that the lubricating system feeding the
caterpillar is operating properly.
Figure 18
If the lubricating system is
not operating properly, shut down machine
operations immediately in order to prevent
damage to the caterpillar.
4. Adjust the fence to the proper measurement
on the scale, and feed the stock through the
blade.
Anti-kickback pawls are
provided to reduce the chance of kickback.
However, to increase safety, never stand in
path of workpiece while feeding stock and/or
operating machine.
Feeding Curved Wood
Excessively curved or warped stock should be
not fed through the rip saw. If the stock has
moderate curvature, it should be fed through the
rip saw with the concave surface down (Figure
19).
Figure 19
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Oil should be checked weekly, and more added
if necessary. Use light 20-weight oil. Change the
oil after 2000 hours of operation. Insufficient oil
may cause fast wear of gears; excessive oil into
the gear reducer may cause oil leakage. Never
overfill the oil tank, and never use recycled oil.
Maintenance
Before doing maintenance on
the machine, disconnect it from the electrical
supply by pulling out the plug or switching
off the main switch! Failure to comply may
cause serious injury.
Refill the oil in the gear reducer until the level
reaches over half its full capacity.
Properly clean chips and sawdust from your
machine after work operations are complete.
Never use your hands, use a brush or
compressed air.
Interior of oil tank must be kept clean at all
times.
The track of caterpillar chain must be kept
lubricated at all times by the machine's
lubrication system.
Optional Accessory
Part No.
Description
SLR12-700
Laser Assembly
Troubleshooting (Electrical)
Trouble
Probable Cause
Remedy
Power source not functioning.
Motor overload relay tripped.
Fuse burned out.
Check three phase power source.
Reset overload relay.
Replace fuse.
Power light won’t
come on (no power).
Power source is insufficient.
YL-60P wire is broken.
Check three phase power source.
Replace YL-60.
Power light won’t
come on (lack of
phase).
Poor connection on magnetic switch.
Poor connection on terminals.
Screw loosened.
Replace magnetic switch.
Replace TB1, TB2.
Tighten screw.
Motor jammed.
Clean motor.
Motor runs
abnormally.
Magnetic switch damaged.
Motor damaged.
Replace magnetic switch.
Replace motor.
Magnetic switch damaged.
Motor burned out.
Replace magnetic switch.
Replace motor.
Motor won’t run.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Mechanical)
Trouble
Probable Cause
Remedy
Saw arbor guard or rear guard not
closed.
Saw arbor won’t run.
Check and close guards.
Caterpillar won’t
move.
Variable speed belt too loose, or
dropped.
Adjust variable speed belt tension or
replace belt. See page 11.
Workpiece slips.
Pressure roller too high.
Saw blade too dull.
Fence is bumped.
Lower the pressure roller.
Replace blade (page 10).
Adjust fence (page 12).
Replace blade (page 10).
Adjust fence (page 12).
Replace blade (page 10).
Adjust fence (page 12).
Fill tank with oil (page 13).
Blow off dust with air gun.
Adjust belt tension (page 11).
Convex cut causes
jointing failure.
Saw blade too dull.
Fence is bumped.
Concave cut causes
jointing failure.
Uneven product
thickness at front and
rear end.
Saw blade too dull.
Fence is bumped.
No oil in lubricator.
Abnormal speed of
link chain conveyor
Oil distributor jammed.
Variable speed belt loosened.
Lower saw blade 0.5 to 1.5mm below
surface of caterpillar (page 12).
Wood is not cut off.
Saw blade position is too high to cut.
Using same saw blade for trimming
and cutting off.
Use correct saw blade.
Insufficient power
causes blade to stop.
Saw arbor belt is loosened.
Fence not square.
Adjust arbor belt tension.
Square fence (page 12).
Finished cut not
square.
Damage caused by poor lubrication
on chain rail and chain block.
Replace chain rail and chain block,
and maintain proper oil level.
Emergency stop button not released.
Safety door cover not closed.
Overload relay tripped.
Check pushbutton (page 9).
Close door.
Power light on, but
machine won’t start.
Replace R1.
Start switch not functioning.
Replace MS1, MS2.
Machine starts briefly
then quits.
Check PB2, PB3. Replace pushbutton
or replace magnetic switch.
Stop pushbutton malfunctioning.
Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call
1-800-274-6848, Monday through Friday (see our website for business hours, www.powermatic.com).
Having the Model Number and Serial Number of your machine available when you call will allow us to
serve you quickly and accurately.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Infeed Body Assembly
Index No. Part No.
Description
Size
Qty
.................SLR12-300 ..............Cover Assembly (Items 1 thru 7)............................................................ 1
.................SLR12-100 ..............Gear Box Assembly (Items 1 thru 10, 33, 36 and 43) ............................. 1
1...............TS-1502041.............Socket Head Cap Screw.....................................M5x16........................ 4
2...............SLR12-101 ..............Gear Box Cover..................................................................................... 1
3...............SLR12-102 ..............Bearing Lock Nut................................................# AN04....................... 1
4...............SLR12-103 ..............Bearing Lock Washer .........................................# AW04.................... 15
5...............BB-51104.................Thrust Bearing....................................................# 51104...................... 1
6...............TS-1503071.............Socket Head Cap Screw.....................................M6x30........................ 7
7...............TS-2361061.............Lock Washer ......................................................M6.............................. 4
8...............SLR12-104 ..............Gear Box Housing................................................................................. 1
9...............SLR12-105 ..............Key.....................................................................7x7x18mm.................. 1
10.............SLR12-106 ..............Lead Screw (Blade Raising)................................TM25-5x160............... 1
11.............SLR12-107 ..............Infeed Body Housing ............................................................................. 1
12.............TS-1524021.............Socket Set Screw...............................................M8x10........................ 6
13.............SLR12-108 ..............Locking Handle...................................................................................... 1
14.............SLR12-109 ..............Bracket.................................................................................................. 1
15.............TS-1504061.............Socket Head Cap Screw.....................................M8x30........................ 6
16.............TS-1551051.............Lock Washer ......................................................M8.............................. 4
18.............SLR12-110 ..............Shaft ..................................................................................................... 1
19.............SLR12-111 ..............Knob ..................................................................................................... 1
20.............SLR12-112 ..............Handle Block......................................................................................... 1
21.............TS-1523031.............Socket Set Screw...............................................M6x10........................ 4
22.............SLR12-113 ..............Shaft ..................................................................................................... 1
23.............SLR12-114 ..............Anti-Kickback Finger............................................................................ 37
24.............TS-1503061.............Socket Head Cap Screw.....................................M6x25........................ 4
25.............SLR12-115 ..............Guide Plate ........................................................................................... 1
26.............SLR12-116 ..............Bracket.................................................................................................. 1
27.............SLR12-117 ..............Shaft Block.......................................................................................... 13
28.............TS-2360121.............Flat Washer........................................................M12............................ 4
29.............TS-2361121.............Lock Washer ......................................................M12.......................... 44
30.............TS-1506091.............Socket Head Cap Screw.....................................M12x60...................... 4
31.............SLR12-118 ..............Taper Pin ...........................................................# 7.............................. 3
32.............SLR12-119 ..............Stop Block............................................................................................. 1
33.............SLR12-120 ..............Small Bevel Gear................................................................................... 1
34.............SLR12-121 ..............Spacer................................................................................................... 1
36.............SLR12-122 ..............Shaft ..................................................................................................... 1
38.............SLR12-123 ..............Handwheel .........................................................# 250.......................... 1
39.............TS-1533032.............Pan Head Machine Screw ..................................M5x10........................ 4
40.............SLR12-124 ..............Cover .................................................................................................... 1
41.............SLR12-125 ..............Lifting Eye Bolt ...................................................M12............................ 1
42.............SLR12-126 ..............Lead Screw (Tracking)........................................................................... 1
43.............SLR12-127 ..............Pin......................................................................Φ4x25mm ................ 14
44.............SLR12-128 ..............Bevel Gear ............................................................................................ 1
45.............SLR12-129 ..............Spacer................................................................................................. 29
46.............SLR12-130 ..............Bushing Pin........................................................................................... 2
47.............SLR12-131 ..............Cover .................................................................................................... 1
50.............SLR12-132 ..............Handwheel .........................................................# 200.......................... 1
51.............TS-0271031.............Socket Set Screw...............................................3/8-16x3/8”................. 1
52.............SLR12-133 ..............Collar .................................................................................................... 2
53.............SLR12-134 ..............Bushing................................................................................................. 1
54.............SLR12-135 ..............Rivet...................................................................#3x5........................... 8
55.............SLR12-136 ..............Scale..................................................................................................... 1
56.............SLR12-137 ..............Lock Handle Label (Saw Spindle) ......................................................... 1
57.............SLR12-138 ..............Handwheel Label (Saw Spindle)............................................................ 1
58.............SLR12-139 ..............Handwheel Label (Press Roller)............................................................. 1
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Infeed Body Assembly
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Arbor Spindle Assembly
Index No. Part No.
Description
Size
Qty
.................SLR12-200 ..............Arbor Spindle Assembly (Items 1 thru 13).............................................. 1
1...............TS-1492041.............Hex Cap Screw ..................................................M12x40...................... 1
2...............TS-2361121.............Lock Washer ......................................................M12.......................... 14
3...............SLR12-201 ..............Arbor Washer ........................................................................................ 1
4...............SLR12-202 ..............Outer Collar........................................................................................... 1
5...............SLR12-203 ..............Arbor Spindle......................................................................................... 1
6...............TS-1503071.............Socket Head Cap Screw.....................................M6x30........................ 7
7...............SLR12-204 ..............Front Cover ........................................................................................... 1
8...............SLR12-BB7208........Ball Bearing........................................................# 7208........................ 2
9...............SLR12-205 ..............Spacer (Inner) ....................................................................................... 1
10.............SLR12-206 ..............Spacer (Outer)....................................................................................... 1
11.............SLR12-207 ..............Spacer, Front......................................................................................... 1
12.............SLR12-208 ..............Bearing Washer..................................................# AW08...................... 1
13.............SLR12-209 ..............Bearing Nut ........................................................# AN08....................... 1
14.............SLR12-210 ..............Adjustment Nut...................................................................................... 1
15.............SLR12-211 ..............Arbor Spindle Housing........................................................................... 1
16.............TS-1540061.............Hex Nut..............................................................M8.............................. 1
17.............TS-1490061.............Hex Cap Screw ..................................................M8x35........................ 1
18.............SLR12-212 ..............Collar Retainer ...................................................................................... 1
19.............TS-1524021.............Socket Set Screw...............................................M8x10........................ 2
20.............SLR12-213 ..............Pivot Shaft............................................................................................. 1
21.............SLR12-214 ..............Adjustment Nut...................................................................................... 1
22.............BB-6207...................Ball Bearing........................................................# 6207........................ 1
23.............SLR12-215 ..............Rear Spacer.......................................................................................... 1
24.............SLR12-216 ..............Spindle Cover........................................................................................ 1
26.............SLR12-217 ..............Spacer................................................................................................... 1
27.............SLR12-218 ..............Spindle Sheave..................................................................................... 1
28.............SLR12-219 ..............Key.....................................................................10x8x40mm................ 1
29.............TS-1550071.............Flat Washer........................................................M10............................ 1
30.............TS-2361101.............Lock Washer ......................................................M10............................ 1
31.............TS-1505031.............Socket Head Cap Screw.....................................M10x25...................... 1
32.............SLR12-220 ..............Saw Blade..........................................................Φ12”x48Tx4W ............ 1
.................SLR12-221 ..............Arbor Wrench (not shown) ..................................................................... 1
.................SLR12-222 ..............T-Wrench (not shown) ........................................................................... 1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Arbor Spindle Assembly
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Motor and Drive Unit Assembly
Index No. Part No.
Description
Size
Qty
1...............SLR12-501 ..............Eye-Bolt ................................................................................................ 1
2...............TS-2311161.............Hex Nut..............................................................M16............................ 2
3...............SLR12-502 ..............Adjustment Nut...................................................M16............................ 1
4...............SLR12-503 ..............Adjustment Bolt ..................................................M16............................ 1
5...............SLR12-504 ..............Key.....................................................................10x8x65 ..................... 1
6...............SLR12-505 ..............V-Belt.................................................................A-56 ........................... 4
7...............SLR12-506 ..............Sheave.................................................................................................. 1
8...............TS-1525011.............Socket Set Screw...............................................M10x10...................... 2
9...............SLR12-507 ..............Adjusting Ring....................................................................................... 1
10.............SLR12-508 ..............Motor........................................................15HP,230V/460V,3PH ............ 1
11.............TS-149105...............Hex Cap Screw ..................................................M10x35...................... 4
12.............TS-2361101.............Lock Washer ......................................................M10............................ 6
13.............SLR12-509 ..............Motor Base............................................................................................ 1
14.............SLR12-510 ..............Shaft ..................................................................................................... 1
15.............SLR12-511 ..............Spacer................................................................................................... 2
16.............TS-1524021.............Socket Set Screw...............................................M8x10........................ 4
17.............SLR12-512 ..............Motor..........................................................2HP,230V/460V,3PH ............ 1
18.............TS-1524041.............Socket Set Screw...............................................M8x16........................ 2
19.............SLR12-513 ..............Reducer Sheave.................................................................................... 1
20.............SLR12-514 ..............Key.....................................................................6x6x60mm.................. 1
21.............TS-1490041.............Hex Cap Screw ..................................................M8x25........................ 4
22.............TS-2361081.............Lock Washer ......................................................M8.............................. 4
23.............TS-1550061.............Flat Washer........................................................M8.............................. 4
24.............SLR12-515 ..............Motor Base............................................................................................ 1
25.............TS-2360121.............Flat Washer........................................................M12............................ 2
26.............SLR12-516 ..............Stud Bolt ............................................................M12x100 .................... 1
27.............TS-1540081.............Hex Nut..............................................................M12............................ 3
28.............SLR12-517 ..............Shaft ..................................................................................................... 1
29.............SLR12-518 ..............Key.....................................................................7x7x40mm.................. 1
30.............SLR12-519 ..............V-Belt.................................................................1220VB30-22 ............. 1
31.............TS-1523031.............Socket Set Screw...............................................M6x10........................ 2
32.............SLR12-520 ..............Reducer Sheave.................................................................................... 1
33.............SLR12-521 ..............Worm Gear Reducer.............................................................................. 1
34.............TS-2361121.............Lock Washer ......................................................M12............................ 4
35.............TS-1492041.............Hex Cap Screw ..................................................M12x40...................... 4
37.............SLR12-522 ..............Oil Nozzle...........................................................PT1/8”........................ 5
39.............SLR12-523 ..............Idle Wheel ............................................................................................. 2
41.............SLR12-524 ..............Sprocket.............................................................10T............................. 1
42.............SLR12-525 ..............Key.....................................................................10x8x60mm................ 1
44.............TS-2311101.............Hex Nut..............................................................M10............................ 2
45.............TS-1491041.............Hex Cap Screw ..................................................M10x30...................... 2
47.............TS-0803052.............Slotted Round Head Machine Screw...................#5-40x5/8”.................. 8
48.............SLR12-526 ..............Brush .................................................................................................... 2
49.............SLR12-527 ..............Rail Bracket........................................................................................... 2
51.............SLR12-528 ..............Rail Body............................................................................................... 1
52.............SLR12-529 ..............Caterpillar Block ................................................................................. .38
53.............SLR12-530 ..............Shaft ................................................................................................... 38
54.............SLR12-531 ..............Retaining Ring....................................................C12 .......................... 76
55.............SLR12-532 ..............Ball Bearing Assembly........................................# UCP205................... 2
56.............SLR12-533 ..............Shaft ..................................................................................................... 1
57.............TS-1504051.............Socket Head Cap Screw.....................................M8x25........................ 8
58.............SLR12-534 ..............Caterpillar Chain Insert........................................................................ 38
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor and Drive Unit Assembly
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Laser Assembly (Optional Accessory)
Index No. Part No.
Description
Size
Qty
.................SLR12-700 ..............Laser Assembly (Items 1 thru 18) ............................................................
1...............TS-1503081.............Socket Head Cap Screw.....................................M6 x 35...................... 2
2...............SLR12-701 ..............Clamp Seat ........................................................................................... 2
3...............SLR12-702 ..............Laser..................................................................................................... 1
4...............SLR12-703 ..............Adjustment Bracket ............................................................................... 1
5...............TS-1502041.............Socket Head Cap Screw.....................................M5 x 16...................... 4
6...............SLR12-704 ..............Bracket.................................................................................................. 1
7...............TS-1501021.............Socket Head Cap Screw.....................................M4 x 8........................ 4
8...............TS-1550021.............Flat Washer........................................................M4.............................. 2
9...............SLR12-705 ..............Mounting Bracket................................................................................... 1
10.............SLR12-706 ..............Cord Holder........................................................................................... 6
11.............SLR12-707 ..............DC Power Connector (Male).................................................................. 1
.................SLR12-714 ..............Transformer Assembly (Items 12 thru 18) .............................................. 2
12.............SLR12-708 ..............DC Power Connector (Female).............................................................. 1
13.............SLR12-709 ..............Fuse...................................................................1A .............................. 1
14.............SLR12-710 ..............Power Switch......................................................................................... 1
15.............SLR12-711 ..............Control Box ........................................................................................... 1
16.............SLR12-712 ..............Transformer with Base Plate.................................................................. 1
17.............TS-1531012.............Philips Pan Head Machine Screw .......................M3 x 6........................ 4
18.............SLR12-713 ..............Power Cord ........................................................................................... 1
19.............TS-1504041.............Socket Head Cap Screw.....................................M8 x 20...................... 4
20.............TS-1550061.............Flat Washer........................................................M8.............................. 4
21.............TS-2361081.............Lock Washer ......................................................M8.............................. 4
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Roller and Frame Assembly
Index No. Part No.
Description
Size
Qty
.................SLR12-300 ..............Cover Assembly (Items 1 thru 7)............................................................ 1
1...............SLR12-301 ..............Cover w/ Dust Port ................................................................................ 1
2...............SLR12-302 ..............Rotation Shaft........................................................................................ 2
3...............SLR12-303 ..............Special Screw........................................................................................ 5
4...............TS-1540071.............Hex Nut,.............................................................M10............................ 7
5...............SLR12-304 ..............Lock Screw............................................................................................ 1
6...............TS-1523011.............Socket Set Screw...............................................M6x6.......................... 1
7...............SLR12-305 ..............Knob ..................................................................................................... 1
8...............TS-2210801.............Hex Cap Screw ..................................................M10x80...................... 3
10.............TS-1503051.............Socket Head Cap Screw.....................................M6x20........................ 2
11.............TS-2361061.............Lock Washer ......................................................M6.............................. 2
12.............SLR12-306 ..............Shaft ..................................................................................................... 3
13.............SLR12-307 ..............Right Bearing Cover .............................................................................. 3
14.............BB-6204...................Ball Bearing........................................................# 6204........................ 6
15.............SLR12-308 ..............Roller .................................................................................................... 3
16.............SLR12-309 ..............Left Bearing Cover................................................................................. 3
17.............SLR12-310 ..............Spring Seat ........................................................................................... 3
18.............SLR12-311 ..............Spring.................................................................................................... 3
19.............SLR12-312 ..............Arm ....................................................................................................... 2
20.............SLR12-313 ..............Spring.................................................................................................... 4
21.............SLR12-314 ..............Arm ....................................................................................................... 2
22.............SLR12-315 ..............Shaft ..................................................................................................... 4
23.............SLR12-316 ..............Grease Fitting.....................................................# 6.............................. 4
24.............SLR12-317 ..............Shaft ..................................................................................................... 4
25.............TS-1523031.............Socket Set Screw...............................................M6x10...................... 18
26.............SLR12-318 ..............Left Bearing Cover................................................................................. 2
27.............BB-6302...................Ball Bearing........................................................# 6302........................ 8
28.............TS-1550041.............Flat Washer........................................................M6.............................. 4
29.............SLR12-319 ..............Left Roller.............................................................................................. 2
30.............SLR12-320 ..............Right Roller ........................................................................................... 2
31.............TS-2286202.............Pan Head Machine Screw ..................................M6x20........................ 4
32.............SLR12-321 ..............Right Bearing Cover .............................................................................. 2
33.............SLR12-322 ..............Left Arm ................................................................................................ 2
35.............SLR12-323 ..............Arm ....................................................................................................... 1
36.............SLR12-324 ..............Shaft ..................................................................................................... 1
37.............TS-1502041.............Socket Head Cap Screw.....................................M5x16........................ 4
38.............SLR12-325 ..............Block..................................................................................................... 2
39.............SLR12-326 ..............Roller Housing....................................................................................... 1
40.............SLR12-327 ..............Locking Handle...................................................M12............................ 1
41.............TS-1524061.............Socket Set Screw...............................................M8x25........................ 3
42.............TS-1540061.............Hex Nut..............................................................M8.............................. 3
44.............SLR12-328 ..............Block..................................................................................................... 2
45.............SLR12-329 ..............Shaft ..................................................................................................... 1
46.............SLR12-330 ..............Anti-Kickback Fingers.......................................................................... 25
47.............SLR12-331 ..............Bracket.................................................................................................. 1
48.............SLR12-332 ..............Shaft ..................................................................................................... 1
49.............SLR12-333 ..............Slide Plate............................................................................................. 1
50.............SLR12-334 ..............Lock Bar................................................................................................ 1
51.............SLR12-335 ..............Needle................................................................................................... 1
52.............TS-1533032.............Pan Head Machine Screw ..................................M5x10........................ 1
53.............TS-1492041.............Hex Cap Screw ..................................................M12x40...................... 2
54.............TS-2361121.............Lock Washer ......................................................M12............................ 2
55.............SLR12-336 ..............Bracket.................................................................................................. 1
56.............TS-2361101.............Lock Washer ......................................................M10............................ 6
57.............TS-1491041.............Hex Cap Screw ..................................................M10x30...................... 6
58.............SLR12-337 ..............Lock Bar................................................................................................ 1
59.............SLR12-338 ..............Cover .................................................................................................... 1
23
Download from Www.Somanuals.com. All Manuals Search And Download.
60.............TS-1534042.............Pan Head Machine Screw ..................................M6x12........................ 2
61.............TS-1504051.............Socket Head Cap Screw.....................................M8x25........................ 1
62.............SLR12-339 ..............Side Guard............................................................................................ 1
63.............SLR12-340 ..............Arm ....................................................................................................... 2
64.............SLR12-341 ..............Special Screw........................................................................................ 2
65.............TS-1550061.............Flat Washer........................................................M8.............................. 2
66.............TS-1490041.............Hex Cap Screw ..................................................M8x25........................ 2
67.............SLR12-342 ..............Safety Guard......................................................................................... 1
68.............TS-1550041.............Flat Washer........................................................M6.............................. 2
69.............TS-1533032.............Pan Head Machine Screw ..................................M5x10........................ 4
70.............SLR12-343 ..............Cover .................................................................................................... 1
71.............SLR12-344 ..............Limit Switch........................................................................................... 1
72.............SLR12-345 ..............Bracket.................................................................................................. 1
73.............SLR12-373 ..............Lock Handle Label (Press Roller)........................................................... 1
74.............SLR12-135 ..............Rivet...................................................................#3x5mm ..................... 2
75.............3312341...................Powermatic Logo................................................................................... 1
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Roller and Frame Assembly
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Table and Stand Assembly
Index No. Part No.
Description
Size
Qty
............SLR12-400FAN........Fence Complete Assembly (Index 15, 20-24, 26-31, 52-58, 77, 81-84) .. 1
1...............SLR12-401 ..............Bracket.................................................................................................. 1
2...............TS-1506051.............Socket Head Cap Screw.....................................M12x40...................... 4
3...............TS-2361121.............Lock Washer ......................................................M12............................ 4
4...............TS-2360121.............Flat Washer........................................................M12............................ 4
5...............SLR12-402 ..............Cover .................................................................................................... 1
6...............TS-1533032.............Pan Head Machine Screw ..................................M5x10...................... 11
7...............TS-2248122.............Pan Head Machine Screw ..................................M8x12........................ 6
8...............SLR12-403 ..............Cover .................................................................................................... 1
9...............SLR12-404 ..............Cover .................................................................................................... 1
10.............SLR12-405 ..............Stand .................................................................................................... 1
11.............TS-1502041.............Socket Head Cap Screw.....................................M5x16........................ 8
12.............SLR12-406 ..............Cover Plate ........................................................................................... 1
13.............SLR12-407 ..............Cover .................................................................................................... 1
14.............TS-1534042.............Pan Head Machine Screw ..................................M6x12........................ 6
15.............SLR12-408N............Gear...................................................................................................... 1
16.............TS-1505031.............Socket Head Cap Screw.....................................M10x25...................... 4
17.............SLR12-409 ..............Bracket.................................................................................................. 2
18.............TS-1550071.............Flat Washer........................................................M10............................ 4
19.............TS-1505061.............Socket Head Cap Screw.....................................M10x40...................... 4
20.............SLR12-410 ..............Fence.................................................................................................... 1
21.............SLR12-411 ..............Special Screw........................................................................................ 1
22.............SLR12-412 ..............Taper Pin ...........................................................# 7.............................. 2
23.............TS-1505051.............Socket Head Cap Screw.....................................M10x35...................... 2
24.............TS-2361101.............Lock Washer ......................................................M10............................ 4
25.............SLR12-413 ..............Retaining Ring....................................................C12 ............................ 2
26.............SLR12-414N............Gear Box............................................................................................... 1
27.............SLR12-415 ..............Handwheel .........................................................# 150.......................... 1
28.............TS-0271031.............Socket Set Screw...............................................3/8”-16x3/8”................ 2
29.............SLR12-416N............Knob Handle ......................................................................................... 1
30.............SLR12-417N............Setting Block ......................................................................................... 1
31.............SLR12-418N............Shaft ..................................................................................................... 1
32.............SLR12-419 ..............Scale..................................................................................................... 1
33.............SLR12-420 ..............Gear Column......................................................................................... 1
34.............TS-1503051.............Socket Head Cap Screw.....................................M6x20........................ 4
35.............SLR12-421 ..............Oil Reservoir ......................................................................................... 1
36.............SLR12-422 ..............Cover .................................................................................................... 1
40.............SLR12-423 ..............Oil Reservoir Contactor ......................................................................... 1
41.............SLR12-424 ..............Oil Tube .............................................................O.D. 4x2.5 mm ........... 5
42.............SLR12-425 ..............Control Panel Bracket............................................................................ 1
43.............TS-1504051.............Socket Head Cap Screw.....................................M8x25........................ 3
44.............TS-1550061.............Flat Washer........................................................M8.............................. 2
45.............SLR12-426 ..............Rotation Seat......................................................................................... 1
47.............TS-1540061.............Hex Nut..............................................................M8.............................. 1
48.............SLR12-427 ..............Control Panel Arm ................................................................................. 1
49.............TS-2361061.............Lock Washer ......................................................M6.............................. 3
50.............TS-1503061.............Socket Head Cap Screw.....................................M6x25........................ 3
51.............SLR12-428 ..............Control Panel......................................................................................... 1
52.............SLR12-429 ..............Side Plate.............................................................................................. 1
53.............SLR12-430 ..............Retaining Ring....................................................C25 ............................ 1
54.............TS-2286201.............Phillips Flat Head Machine Screw.......................M6x20........................ 4
55.............SLR12-431 ..............Clamping Strip....................................................................................... 1
56.............SLR12-432 ..............Lock Lever............................................................................................. 1
57.............SLR12-433 ..............Clamp.................................................................................................... 1
58.............SLR12-434 ..............Cover .................................................................................................... 1
60.............SLR12-436 ..............Panel..................................................................................................... 1
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Index No. Part No.
Description
Size
Qty
62.............SLR12-437 ..............Emergency Stop Button......................................................................... 1
64.............SLR12-438 ..............Start Button........................................................................................... 2
65.............SLR12-440 ..............Stop Button ........................................................................................... 2
67.............SLR12-442 ..............Start Button, Power On.......................................................................... 1
68.............SLR12-443 ..............Electrical Control Assembly ................................................................... 1
69.............SLR12-444 ..............Handle................................................................................................... 2
70.............SLR12-445 ..............Bracket.................................................................................................. 1
71.............SLR12-446 ..............Shaft ..................................................................................................... 1
72.............SLR12-447 ..............Bracket.................................................................................................. 1
73.............TS-1491061.............Hex Cap Screw ..................................................M10x40...................... 2
74.............SLR12-448 ..............Spring.................................................................................................... 1
75.............TS-1490061.............Hex Cap Screw ..................................................M8x35........................ 2
76.............TS-1540061.............Hex Nut..............................................................M8.............................. 2
77.............SLR12-449 ..............Knob Handle ......................................................................................... 1
78.............SLR12-450 ..............Leveling Screw...................................................M16x80...................... 4
79.............TS-2311161.............Hex Nut..............................................................M16............................ 4
80.............SLR12-451 ..............Foot Pad ............................................................................................... 4
81.............TS-1524021.............Socket Set Screw...............................................M8 x10....................... 4
82.............TS-1523031.............Socket Head Cap Screw.....................................M6 x10....................... 1
83.............SLR12-483 ..............Clamping Shaft...................................................................................... 2
84.............TS-1525031.............Socket Set Screw...............................................M10 x16 ..................... 1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Table and Stand Assembly
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List: Electrical Control Panel (SLR12-443)
Index No. Part No.
Description
Size
Qty
1...............SLR12-601 ..............Control Relay................... R1 .............................MY2NJ-200/220VAC .. 1
2...............SLR12-602 ..............Timer............................... T1................................................................. 1
3...............SLR12-603 ..............Transformer..................... PT .............................0V~440V .................... 1
4...............SLR12-604 ..............Terminal Plate ................ TB ................................................................ 1
5...............SLR12-605 ..............Fuse................................ PTF1 .........................10x38-4A.................... 1
6...............SLR12-606 ..............Fuse ............................... PTF2 .........................10x38-4A.................... 1
7...............SLR12-607 ..............Fuse ............................... F................................10x38-4A.................... 1
8...............SLR12-608 ..............Switch ............................. M2.............................LC1D096.................... 1
9...............SLR12-609 ..............Overload ........................ OL2 ...........................LR3D126 5.5~8A........ 1
10.............SLR12-610 ..............Switch ............................. M1.............................LC1D256.................... 1
11.............SLR12-611 ..............Overload ........................ OL1 ...........................LR3D326, 23~32A...... 1
12.............SLR12-612 ..............Switch ............................. D1 .............................LC1D256.................... 1
13.............SLR12-613 ..............Switch ............................ S1..............................LC1D186.................... 1
14.............SLR12-614 ..............Terminal ......................... TM............................................................... .1
15.............SLR12-615 ..............Grounding Block.............. G .................................................................. 1
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections – 3 Phase, 230V, 60Hz
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections – 3 Phase, 460V, 60Hz
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Preventive Maintenance
Checklist for Model SLR12 Straight Line Rip Saw
[
[
[
[
]
]
]
]
Work area around machine marked off clearly.
Non-skid floor strips in area where operator normally stands.
Inspect entire machine for loose bolts, nuts, screws. Tighten and replace as necessary.
Clean table area, removing sawdust and chips with a soft bristle brush. Remove gum and pitch
with oven cleaner.
[
[
]
]
Lubricate appropriate places with a good grade non-hardening grease.
Clean table and fence surface. If rusted, use paste mixture of household ammonia, a good
commercial detergent and 000 steel wool. Wash surface down with hot, soapy water, rinse and
dry thoroughly. Coat surface with talcum powder, rubbing briskly into surface with a clean
blackboard eraser.
[
[
[
[
[
]
]
]
]
]
Check blade condition; should be sharp and free of nicks or grooves.
Check belt condition. Replace as needed. Dress with parafin. Check belt tension.
Check motor for loose wiring and sawdust congestion, pulleys tight and in line.
Check bearings. Replace any bad or suspect bearings immediately.
Fence properly aligned with blade.
427 New Sanford Road
LaVergne, TN 37086
Phone: 800-274-6848
Download from Www.Somanuals.com. All Manuals Search And Download.
|