Model No.:OV2-420/OV2-600/OV2-800/OV2-1250/OV2-1800
OV2-2200/OV2-2600/OV4-840/OV4-1200/OV4-1600
65-C0486-MA
ꢀꢁ：A2
INTRODUCTION
Amplifiers provide high-performance sound reinforcement for your mobile audio equipment.
It s versatility enables compatibility with optional Equalizers,Frequency Dividing Network
Crossovers,and other audio processors in a customized system.The Multi-Mode bridging
Capabilities allow flexibility in hosting several different speaker configurations.
To achieve optimum performance,it is highly recommended that you read this Owner s
Manual before beginning installation.
FEATURES
Full Mosfet Power Supply
PWM Circuitry
Full Selectable Crossover Hi/Full/Low
Three Way Protection Circuit
2 Ohm Stable Stereo
,
Owner s Manual
Tri-Mode Capable
Super Cool Blue Led
Chrome Top Plate Panel
Variable Low Pass 40Hz-250Hz/30Hz-500Hz
Variable Hi Pass 40Hz-250Hz/50-500Hz
Variable 24 dB Bass Boost @ 40Hz
Frequency Response: 10Hz to 30 KHz
S/N Ratio: 98dB
THD: 0.02%
System Distress Indicator
4 Gauge Power/Ground Connection
Platinum Plated RCA Connectors
Line Output
High/Low Level Inputs With Floating Ground
OV2-420/OV2-600/OV2-800/OV2-1250/OV2-1800
OV2-2200/OV2-2600/OV4-840/OV4-1200/OV4-1600
WARNING
High powered audio systems in a vehicle are capable of generating Live Concert high
levels of sound pressure,Continual exposure to excessively high volume sound levels may
cause hearing loss or damage.Also,operation of a motor vehicle while listening to audio
equipments at high volume levels may impair your ability to hear external sounds such as;
horns,warning signals,or emergency vehicles,thus constituting to a potential traffic hazard.
In the interest of safety,Consumer Electronics recommends listening at lower volume levels
While driving.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
B.VARIABLE LOW-PASS FILTER(40Hz-250Hz)
WIRING CONNECTIONS
For use as a dedicated subwoofer channel,set filter switch to LPF .Adjust variable
crossover frequency with control as desired.The amplifier input circuit filters out
everything above 40....250Hz(depends on the adjustment of the frequency control),
so only the deepest bass notes are amplified.
A.CONNECTING THE POWER
CAUTION:
AS A PRECAUTION,IT IS ADVISABLE TO DISCONNECT THE VEHICLE S BATTERY BEFORE MAKING CONNECTION
TO THE +12 VOLTS SUPPLY WIRING.
C.VARIABLE HIGH-PASS FILTER(40Hz-250Hz)
For use as a dedicated high ranged channel,set filter switch to HPF .The input
circuit filters out all frequencies below 40Hz....250Hz.
4/8 GAUGE(Or thicker if planning for additional Amplifiers)wire is recommended for both the
power and ground wires.12 Gauge,for the remote turn wire.Both types are
available at most Mobile Audio Dealers or Installation Shops.
D.BASS BOOST
By using the bass boost function the deepest bass notes at 50Hz are emphasized.
(1)GROUND:To Vehicle Chassis
To avoid unwanted ignition noise caused by ground loops,it is essential that the
Amplifier be grounded to a clean,bare,metal surface of the vehicles chassis.
BASS BOOST
NOTE:
GROUND WIRE SHOULD NOT BE EXTENDED MORE THAN 3 FT.(1 METER).
OV2-1250/OV2-1800/OV2-2200/OV2-2600
(2)+12Volt(Fused) Constant Power:To Battery(+)
Due to the power requirements of the Amplifier,this connection should be made
directly to the positive (+) terminal of battery.For safety measure,install an in-line Fuse
Holder (not included) as close to the battery positive (+) terminal as possible with an
ampere rating:not to exceed total value of fuses in Amp.
OV2-420:20A/OV2-600:30A/OV2-800:20AX2/OV2-1250:25AX2/OV2-1800:30AX2
OV2-2200:25AX3/OV2-2600:30AX3/OV4-840:20AX2/OV4-1200:25AX2/OV4-1600:40AX2
E.CONNECTING HIGH LEVEL INPUTS
(3)Remote Turn-On Input:To Power Antenna output of Car Stereo
NOTE:
DO NOT CONNECT THESE HIGH LEVEL INPUT WIRES IF YOU ARE USING THE LOW LEVEL INPUT RCA JACKS.
CAUTION
NOTE THAT ONLY POSITIVE(+)WIRES ARE USED.DO NOT CONNECT SPEAKER NEGATIVES.
This Amplifier is turned ON remotely when the vehicle s stereo is turned ON .
NOTE:
IF YOUR SOURCE UNIT DOES NOT HAVE AN ACTIVE +12 VOLT LEAD WHEN IT IS TURNED-ON,YOU CAN
EITHER INSTALL AN AUXILIARY SWITCH,OR YOU CAN TAP-INTO AN IGNITION LEAD;NOTE HOWEVER,THAT
YOUR AMPLIFIER WOULD TURN-ON,EVERY TIME YOU START YOUR CAR IF YOU CHOSE THE IGNITION OPTION.
OV2-420/OV2-600
CHASSIS GROUND-Black
CH1(-)
CH2(-)
OV2-420/OV2-600/OV2-800/OV2-1250/OV2-1800
OV2-2200/OV2-2600/OV4-840/OV4-1200/OV4-1600
12V
REM
GND
POWER INPUT
Fuse
CH1(+)
CH2(+)
Near Battery
BATTERY
Remote Turn-ON is
connected to Radio s power
antenna lead or a switchable +12V
Vehicle chassis ground
6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OV4-840/OV4-1200/OV4-1600
INPUT SENSITIVITY(LEVEL) CONTROL
CHASSIS GROUND-Black
In order to achieve maximum signal-to-noise performance,this control adjusts the signal
level from your Car Stereo/Source,to match the Amplifier sensitivity.It is NOT a volume
control.
3 CH(-)
3 CH(+)
1 CH(-)
1 CH(+)
To adjust,proceed as follows:
a.Set INPUT LEVEL Control at mid-point.
b.Listen for audible distortion as you increase the Car Stereo VOLUME control.If none
is heard,turn the adjustment level control toward to MAX in stages,until the onset of
audible distortion is heard,then decrease to MIN level prior to the immediate
point of audible distortion.
C.If distortion is immediately heard,turn control to MIN until the sound is clear.
NOTE:
NOT PERFORMING ABOVE ADJUSTMENT PROCEDURE AND/OR SIMPLY SETTING THIS CONTROL AT OR NEAR
MAX POSITION,MAY INDUCE ELECTRICAL AUDIO NOISE INTO THE SYSTEM.
4 CH(+)
4 CH(-)
2 CH(+)
2 CH(-)
OV2-420/OV2-600
F.CONNECTING LOW LEVEL INPUTS (RCA Jacks)
NOTE:
DO NOT USE IN CONJUNCTION WITH HIGH LEVEL INPUT WIRES.
Wire routing is CRITICAL for NOISE FREE PERFORMANCE,Observe the following:
1.Always use high quality RCA type shielded cables.
2.Always use the shortest lenght possible.If the cable is too long,make an S type
loop(not a coiled loop)in the center of the cable to take up any excess.
3.Never cut the shielded cable and re-splice it.
Input Sensitivity Control
4.Never route any Amplifier input cables near nor parallel to speaker outputs,high
energy ignition wires,nor near computer controlled ignition circuit units (Computer
units may be found behind or under the dash panel in late model cars).
OV4-840/OV4-1200/OV4-1600
POWER INDICATOR LED
This METER LAMP will illuminate when the amplifier is turned ON .If it fails to illuminate,
check the power connections to the Amplifier and fuses.
PROTECTION CIRCUIT
Should the Amplifier be SHORT CIRCUITED overloaded or overheated,the protection
circuit will SHUT-DOWN the Amplifier.
Input Sensitivity Control
CAUTION
THIS AMPLIFIER WAS DESIGNED TO BE USED WITH EITHER 2 OHM STEREO/CHANNEL OR 4 OHM EACH
MONO BRIDGED CHANNEL.IN THE CASE OF TRI-MODE OPERATION,USE EITHER 8 OHM STEREO CHANNEL
SPEAKERS AND 4 OHM SUB OR VICE VERSA.SEE THE SECTION TRI-MODE FOR FURTHER INFORMATION
ON PROPER USE.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OV2-800/OV2-1250/OV2-1800/OV2-2200/OV2-2600
(C)TRI MODE
TRI MODE OPEATIONAL OUTPUT allows a Crossover(Subwoofer) to be operated in MONO
mode while the main speaker is playing in stereo.
Leave the Crossover(Subwoofer)Switch on"FULL" position.
Use a 100Volt,non-polar capacitor for a high pass crossover and a wire coil (inductor)to
block high frequencies from the Crossover (Subwoofer)as shown in the figure below.
Capacitor and inductor values as written in the below determine the crossover
frequencies.
The front and rear channels of this amplifier get this capability.
Only the rear left and right channels are shown below.
Input Sensitivity Control
INDUCTOR
LOW PASS FILTER
CONNECTING THE SPEAKERS
OV2-420/OV2-600/OV2-800/OV2-1250/OV2-1800/OV2-2200/OV2-2600
(A)STEREO MODE
LEFT CHANNEL
2-4Ohm
CAPACITOR
HIGH PASS FILTER
(B)MONO MODE
COMPONENT VALUES FOR 6dB PASSIVE CROSSOVER
FREQUENCY
INDUCTOR
CAPACITOR
470uF
80Hz
7.5mH
6.5mH
5.5mH
4mH
100Hz
120Hz
150Hz
330uF
330uF
220uF
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
(D)6 CHANNEL MODE
Model:OV4-840/OV4-1200/OV4-1600
(A)4 CHANNEL MODE
4CH
3CH
2-4Ohm
2-4Ohm
RIGHT
WOOFER
8 Ohm
INDUCTOR
LOW PASS FILTER
3CH
4-8Ohm
CAPACITOR
HIGH PASS FILTER
4CH
4-8Ohm
1CH
2CH
2-4Ohm
2-4Ohm
(B)3 CHANNEL MODE
4CH
3CH
2-4Ohm
2-4Ohm
1CH
4-8Ohm
CAPACITOR
HIGH PASS FILTER
2CH
4-8Ohm
INDUCTOR
LOW PASS FILTER
LEFT
WOOFER
8 Ohm
1CH/2CH BRIDGE
4Ohm
4Ohm
3CH/4CH BRIDGE
(C)2 CHANNEL MODE
COMPONENT VALUES FOR 6dB PASSIVE CROSSOVER
FREQUENCY
INDUCTOR
CAPACITOR
470uF
80Hz
7.5mH
6.5mH
5.5mH
4mH
100Hz
120Hz
150Hz
330uF
330uF
220uF
4Om
1CH/2CH BRIDGE
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING GUIDE
WARNING
SYMPTOMS
CHECK POINTS
CURE
system
Check fuses in amplifier.
Be sure Turn-on lead is connected
Check signal leads.Check gain
control.
In the power
LED illuminated?
Check Tuner/Deck volume level.
Clean contacts on fuse holders.
NO SOUND
Check for speaker short or
amplifier overheating.
Is the Diagnosis
LED illuminated?
No power to power wire
Repair power wire or connections.
No power to remote
wire with receiver on
AMP NOT
SWITCHING
ON
Check connections to radio.
Check fuse
Fuse broken
Inspect for short circuit or an
open connection.
Check Speaker Leads
NO SOUND
IN ONE
CHANNEL
Reverse Left and Right RCA inputs
to determine if it is occurring
before the amp.
Check Audio Leads
Be sure proper speaker load
impedance recommendations
are observed.
AMP
TURNING OFF
MEDIUM/HIGH
VOLUME
Check Speaker load
impedance
(If you use an ohmmeter to check
speaker resistance,please
remember that DC resistance and
AC impedance may not be the
same.)
Temperature shutdown
Turn radio down
PROTECTION
LED ON (RED)
Speaker wires short circuit
Separate speaker wires and insulate
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
MODEL NO
OV2-420
420W
OV2-600
600W
OV2-800
800W
OV2-1250
1250W
OV2-1800
1800W
MAX Power@2 Ohm
RMS
RMS
@4 Ohm
@2 Ohm
80WX2CH
95WX2CH
120WX2CH
150WX2CH
180WX2CH
220WX2CH
280WX2CH
300WX2CH
380WX2CH
95WX2CH
190W
240W
360W
<0.02%
560W
<0.02%
760W
Bridged Power
THD
<0.02%
<0.02%
<0.02%
Signal/Nosie Ratio
Frequency Response 1.0dB
>98dB
>98dB
>98dB
>98dB
>98dB
10Hz-30KHz
40Hz-250Hz
40Hz-250Hz
10Hz-30KHz
40Hz-250Hz
40Hz-250Hz
10Hz-30KHz
30Hz-500Hz
50Hz-500Hz
10Hz-30KHz
30Hz-500Hz
50Hz-500Hz
10Hz-30KHz
30Hz-500Hz
50Hz-500Hz
HPF
LPF
Input
Low Level
High Level
10K Ohms
10K Ohms
10K Ohms
10K Ohms
10K Ohms
Impedance
Fuse
100 Ohms
20A
100 Ohms
30A
100 Ohms
20AX2
100 Ohms
25AX2
100 Ohms
30AX2
11.1X2.3X7.2
NO
11.1X2.3X9
NO
11.1X2.3X10.6
NO
11.1X2.3X12.8
YES
11.1X2.3X18.5
YES
Dimension(WxHxL):inch
BASS KNOB
FEATURES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
SPECIFICATIONS
MODEL NO
OV2-2200
2200W
OV2-2600
2600W
OV4-840
840W
OV4-1200
1200W
OV4-1600
1600W
MAX Power@2 Ohm
RMS
RMS
@4 Ohm
@2 Ohm
370WX2CH
450WX2CH
450WX2CH
540X2CH
80WX4CH
95WX4CH
100WX4CH
125WX4CH
150WX4CH
180WX4CH
900W
1080W
<0.02%
190WX2
<0.02%
250WX2
<0.02%
360WX2
<0.02%
Bridged Power
THD
<0.02%
Signal/Nosie Ratio
Frequency Response 1.0dB
>98dB
>98dB
>98dB
>98dB
>98dB
10Hz-30KHz
30Hz-500Hz
50Hz-500Hz
10Hz-30KHz
30Hz-500Hz
50Hz-500Hz
10Hz-30KHz
40Hz-250Hz
40Hz-250Hz
10Hz-30KHz
40Hz-250Hz
40Hz-250Hz
10Hz-30KHz
40Hz-250Hz
40Hz-250Hz
HPF
LPF
Input
Low Level
High Level
10K Ohms
10K Ohms
10K Ohms
10K Ohms
10K Ohms
Impedance
Fuse
100 Ohms
25AX3
100 Ohms
30AX3
100 Ohms
20AX2
100 Ohms
25AX2
100 Ohms
40AX2
11.1X2.3X20.5 11.1X2.3X10.6
YES YES
11.1X2.3X12.8
NO
11.1X2.3X12.8
NO
11.1X2.3X18.5
NO
Dimension(WxHxL):inch
BASS KNOB
FEATURES AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Download from Www.Somanuals.com. All Manuals Search And Download.
|