Form No. 1-739 R
May, 2000
INSTALLATION and OPERATING
INSTRUCTION MANUAL
MDV SPREADER
PART NO.
62228
MODEL
M-940
LENGTH CAPACITY RATING
9 FT.
9 FT.
3.4 CU YD
4.2 CU YD
4.7 CU YD
17,000
19,000
20,000
62234
M-944
62246
M-1044
10 FT.
INCLUDED IN THIS MANUAL
SAFETY ALERT............................................................................... 2
SPREADER ASSEMBLY INSTRUCTIONS.....................................3-5
SPREADER OPERATION..............................................................6-8
SPREADER MAINTENANCE.......................................................... 9
HYDRAULICS..............................................................................10-11
SPREADER PARTS LISTS & EXPLODED VIEW..........................12-36
WARRANTY ................................................................................... 37
Meyer Products reserves the right, under its continuing product improvement program, to change construction or design details,
specifications and prices without notice or without incurring any obligation.
18513 Euclid Ave. • Cleveland, Ohio 44112-1084
Phone 486-1313 (Area Code 216)
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in U.S.A. ©2000
ASSEMBLY INSTRUCTIONS AND INSTALLATION
INSTALLATION INSTRUCTIONS:
The Meyer MDV Series Spreaders can mount and store as a single unit. The Meyer MDV Series
Spreader will mount on most 15,000-20,000 GVW trucks as well as larger trucks.
WARNING
DO NOT OVERLOAD THE VEHICLE. It is quite possible to overload the vehicle by
improperly mounting or over loading the spreader. This could result in dangerous stability
and braking problems. Always consult and follow the truck manufacturer’s instructions.
!
!
WARNING
BEFORE BEGINNING ANY INSTALLATION ON THIS UNIT, disconnect the spreader
battery negative cable if already installed.
1. Place the spreader in the rear of truck with the engine / hydraulic motor to the rear of the truck. Center
the spreader (side to side) in the truck. The spreader should extend past the rear of the outer most part
of the truck (i.e: truck bed, bumper) approximately 18 inches.
Caution: Insure that the spreader cannot tip when the spinner assembly is attached.
!
SPINNER ASSEMBLY
a. Raise engine shroud and prop it open with the support rod. (if engine driven model)
b. Slide the spinner frame assembly into the rear of the longitudinals with the spinner back plate
toward the rear.
c. Bolt the spinner to the longitudinals using the four (4) 3/8" x 1” bolts, 3/8” flange nuts and
flatwashers from hardware bag located on the spinner. Using one (1) 3/8" x 1" bolts, flatwashers
and flange nut from hardware bag, bolt the top portion of the spinner back plate to the engine
plate.
d. Install roller chain between the gear box sprocket and the spinner sprocket. Make sure sprockets
are in line with each other. The roller chain is tightened, first by loosening all four 3/8" bolts on
the back plate. Then, pull the entire bearing/shaft assembly in such a way to achieve the proper
amount of chain tension. Make sure the spinner shaft is straight up and down before retightening.
2. Reposition the spreader in the truck, just short of making contact with the rearmost part of the truck bed,
bumper, pintle hook etc. Bolt the unit to the truck using a minimum of six 1/2" - grade 5 bolts and
corresponding washers and locknuts. The Spreader is designed to sit flat on the bed of the truck,
supported by the longitudinal/sides. DO NOT SUPPORT THE SPREADER BY THE BODYJACKS
ALONE !! UNIT IS NOT DESIGNED FOR CHASSIS MOUNT APPLICATION !
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTION FOR
ELECTRIC THROTTLE CONTROL
WARNING
!
1.
Disconnect battery, NEGATIVE CABLE (if already installed).
2.
Spreaders with factory installed throttle controls do not require installer hook-up to the
engine. The actuator has been installed and tested at the factory.
3.
4.
5.
Raise the engine shroud and securely prop it in place with the prop rod. The installer will
have to remove the ties securing the coiled actuator cable to the top of the engine.
The throttle actuator cable plugs into the in-cab control panel after being routed from the
cab of the vehicle to the rear of the mounted spreader.
Select a suitable location in the cab of the vehicle to mount the throttle control box.
(Do not mount at this time.)
WARNING
!
Consult vehicle manufacturer for acceptable mounting locations. Improperly mounting the control
box could interfere with air bag(s) and the other functions of the occupant protection systems,
such as knee bolsters!
6.
After the location of the control panel is determined, the cable must be routed to the rear of the
spreader, so the hookup can be made with the actuator cable plug. Route the conductor cable,
attached to the control, to rear of truck, under truck, securing as needed. Allow enough cable
for the control panel to be mounted in the cab.
7.
The routed cable must be clear of all moving or hot parts on the spreader or vehicle. Secure
the cable with the ties provided. Excess cable must be coiled up and secured.
8.
9.
Locate and mount the control panel (with screws supplied).
For permanent cable mount at rear of the truck, a mounting bracket is supplied.
10. Slide boot over cable then, wire the control panel cable end into the socket (wire colors and
locations are identified on the socket). The rubber socket boot must be installed for weather
resistant seal.
11. Fill boot from cable side with a good grade of dielectric grease to help reduce corrosion on
terminals.
12. Install a 12 volt battery with 4- ampere hour rating, recommended for winter use (if not already
done). The battery hold-downs furnished will accept any 2 SM Series battery.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
!
Use safety glasses or other face protection against possible battery explosion. Do not smoke
and avoid other sources of ignition.
13. Attach the positive battery cable (each end must have a rubber boot) to the positive terminal of
the solenoid and to the positive terminal of the battery Make sure these protective boots are
covering the positive terminal post on the battery and on the solenoid.
14. Connect the negative battery terminal to the battery hold down post. When finished, make sure
all wires are away from moving parts and lower engine shroud.
15. Plug cable from the spreader into socket mounted on the truck, Step 9.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
!
WARNING
BEFORE OPERATING THE CONTROL PANEL - MAKE SURE THAT NO ONE IS INSIDE
THE HOPPER OR NEAR THE SPINNER.
1. Electric Throttle Control Panel Switch functions
(Sequence of Operations)
CHOKE
START
ON
HI
LO
MOUNTING
TABS
CONV.
OFF
RED LENS
A. ON/OFF System power activated (ready to start). Spreader engine is not running.
Spreader conveyor is not engaged.
B. START (Engine only)
1
2. Choke
. OnOn switch
depressed.
(cold engine ) Hold down for 5 seconds to move the throttle actuator to the
choke position.
Note: Choking a warm engine may not be necessary
Hold down until engine starts.
3. Start
4. LO / HI
Decreases / increases engine speed - adjust as engine warms up. Lo will
stop the choke function.
C. TO ENGAGE Spreader Conveyor
1. Push CONV switch only after you are sure no one is in the hopper or near the spinner! This lights up
the red indicator light, if light does not light, take care to verify that the light is not malfunctioning.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
D.
E.
F.
TO CONTROL Conveyor Speed.
1.
2.
Hold HI to increase speed. NOTE: Do not hold switch in HI position after the desired
RPM is achieved or you will choke and/or stall the engine.
Hold LO to decrease speed.
TO DISENGAGE Spreader Conveyor.
1.
Tap START switch momentarily so that red indicator light goes out. Do not fully
depress the START switch, only half way is needed. Only the conveyor stops, the
engine continues to run.
TO TURN ENGINE OFF (with or without conveyor running).
1.
2.
Depress LO on throttle control to reduce setting to idle (this prevents engine flooding
and hard starting).
Push OFF position on the ON/OFF switch.
NOTE: OFF can be pushed at anytime during spreader operation to cut power to the unit.
However, you should normally use steps under F above.
(Once the off switch is depressed - the starting procedure must be followed for engine re-start.)
G.
Do not attempt to start the engine with the conveyor engaged. (CONV switch light will be lit to
indicating its’ being on.)
WARNING
!
1 . As with all power equipment, safety is the number one concern.
2.
3.
Do not operate this equipment until you fully understand how it functions.
Before starting engine, be sure that no one is near the rear of the unit and that no
one is inside the unit!
4.
Do not start the engine or engage the conveyor (which is interconnected to the
spinner); until everyone is clear from moving parts and flying material from the
spinner.
SPREADER OPERATION
A. Start the engine and engage the clutch. The amount of material spread, depends on engine speed and
gate opening. Decreasing RPM and/or gate height will decrease amount spread; the inverse holds true
also. Notice that the electric clutch can be engaged or disengaged at any time and at any engine RPM.
However, since engagement time and torque is almost instantaneous, to prevent premature spinner chain
failure and chain tension loss, it is recommended that the electric clutch be engaged at the lowest possible
RPM without stalling the engine.
If the truck is to be driven for an extended period of time while the spreader is not operating, it is best to turn
off the gas at the carburator inlet to prevent the carburator from overfilling with fuel.
Before loading the spreader the first time, start and stop the conveyor several times to break in the clutch.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
!
ALWAYS STAND AT A SAFE DISTANCE AWAY FROM THE SPINNER WHILE OPERATING
ALWAYS WEAR EYE PROTECTION WHEN OUTSIDE OF THE TRUCK CAB WHILE
SPREADER IS RUNNING.
B. Spread pattern depends on baffle settings and spinner RPM. Maximum spread width is 30 ft.
1. Speeding up or slowing down the engine will increase or decrease spread pattern width.
2. Internal baffle adjustments will move the spread pattern to the right or left.
3. External baffle adjustments will block spreading to the right or left side.
DESIRED SPREAD PATTERN
BAFFLE SETTING
INTERNAL EXTERNAL
All Three UP
RH - Up
DownLH
Centered Behind Truck
All Material to the Right
Both Down
RH - Up
LH
-
-
-
-
D
U
All
Material
to
the
Left
RH
-
LH
DownLH
Behind Truck and Left
Behind Truck and Right
Windrow Behind Truck
RH - Down
LH - Up
RH - Up
LH
RH - Med.
LH - Up
RH - Up
-
DownLH
All - Down
-
M
RH - Down
LH - Down
4. External Baffles can be lowered to an intermediate position to baffle down the particles
that may otherwise leave the spinner at a high trajectory.
C. CALIBRATION
The average lbs. of salt per gearbox shaft revolution per inch of gate height is 6.7 Ibs.
GATE HEIGHT AVG. LBS/REV.
AVG. LBS/MIN.
AVG. LBS/MIN.
AT FULL ENGINE RPM
AT 7 GPM HYD OIL FLOW
1”
3”
5”
7"
6.7
20.1
33.5
46.9
260
780
200
580
1300
1800
970
1350
8
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WARNING
!
DO NOT ATTEMPT TO LIFT THE SPREADER BY THE CENTER LIFT OR
CORNER LIFT HOOKS WITH MATERIAL IN THE SPREADER.
1
Grease idler bearings on idler shaft take up assembly, outboard bearing on gearbox output shaft, and
lower spinner bearing every ten hours of operation.
2. Grease input shaft bearing on gearbox every fifty hours of operation. CAUTION! Over greasing may
cause seal damage. The gearbox must be filled to oil level plug with SAE 90 gear type lubricant. Keep
breather plug clean.
3. Drag chain slack on V-boxes should be checked periodically and taken up if distance between center
line of rear sprocket and point where chain contacts lower flange on longitudinal is less than eight (8)
inches.
4. If the spreader is equipped with a gasoline engine, it should be maintained per engine manufacturer’s
instruction. (Instructions and parts book is enclosed.)
5. V-belt tension must be maintained. The v-belt can be tightened by loosening engine hold-down bolts
and sliding engine as required. CAUTION! Over tightening may damage gearbox.
6. Roller chain tension must be maintained. It is adjusted by loosening the spinner mounting bearings and
sliding the bearings. Make sure the spinner shaft is straight up and down before retightening. Oil
chain often and at end of season.
7. When the box is not in use, it should be washed out. If the box is put in storage, all surfaces should be
oiled or painted after washing.
8. For HYDRAULIC SPREADERS, maintain oil level three fourths (3/4) full in reservoir with clean high
grade non-foaming hydraulic oil; recommended viscosity 100-200 SSU. Operating temperature should
be limited to 180 degress F. Replace filter cartridge #62382 at least twice a year.
9. If chain becomes stuck or “froze” to the floor to the point where the clutch cannot pull the load, never
attempt to free chain using a pipe wrench or any other tool on the output shaft. The gearbox is designed
to accept torque from input shaft only. Trying to turn output shaft will strip the gears, thus voiding the
warranty.
10. To minimize problems and extend the life of the Electric Clutch, the following is highly recommended
a. Before starting unit, make sure the drag chain is free (not stuck or “froze” to the floor). If the drag
chain is stuck, this can cause the clutch to burn up.
b. After the using season is over, remove clutch from unit, and clean thoroughly.
c. After cleaning, coat both mating surfaces of the clutch with oil or light weight grease.
NOTE: The Oil or Grease must be removed prior to the next using season.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HYDRAULICS
!
WARNING
Leaking high pressure fluids can inject themselves under the skin of persons near a leak, creating grave
medical risks. TAKE CARE TO AVOID EXPOSURE TO HIGH PRESSURE FLUIDS.
1 . Hydraulic components should be kept as clean as possible during assembly operations.
2. Galvanized pipe and pipe fittings must not be used because flaking or galvanizing material can cause
damage to major hydraulic components.
3. A pipe joint sealant, compatible with hydraulic oil, must be applied to all screwed fittings. (Teflon tape is
not recommended.)
4. Hose should be protected where severe wear may be caused by vibration or sliding movement.
5. Long runs of hose should be supported by tie wiring or clamping.
6. Pressure and return hoses, connected to hydraulic motors, may be reversed for proper motor rotation.
Spinner rotates in a clockwise direction when looking down from top.
7. Use hose manufacturer’s recommendations for fitting re-useable hose ends.
8. Hydraulic pumps must be mounted so shaft rotates in direction of arrow.
9. Locate reservoir as close to pump as possible. It may be installed on truck frame or truck box.
10. Hydraulic return line filter is screwed directly onto reservoir with cartridge down. Oil must flow through
filter in direction of arrow on filter.
11. Install the quick connect couplings so that when disconnected, there is a male and female on the truck
as well as on the spreader. This way, hoses will always be hooked up properly. and hose ends can be
coupled together when spreader is in storage to prevent system contamination.
12. See page 11 for valve assembly
13. Operate hydraulic system for several minutes to warm up. Check all connections for leaks.
14. After running, refill reservoir to three fourths full.
CONTROL AND HYDRAULIC SYSTEM SPECIFICATIONS
*Hydraulic Oil................................... Good Grade of MS10W Hydraulic Oil Which has
wear, oxidation and foam inhibitors.
*Oil Filter.......................................... 10 Micron Element Return Line Filter.
*Relief Valve Setting1500 PSI
*Oil Flow .......................................... 0 - 10 GPM - With single flow valve connect
conveyor and spinner with dual flow valve.
*Oil Flow .......................................... 0 - 15 GPM - With dual flow valve connect separate
pressure line to conveyor and spinner motor.
Download from Www.Soman1ua0ls.com. All Manuals Search And Download.
DUAL FLOW VALVE/STAND INSTALLATION INSTRUCTIONS
1. IMPORTANT: A pipe joint sealant
compatible with hydraulic oil must be
applied to all screw fittings. (Teflon Tape
Sealant Is Not Recommended)
2. Hose ends connected to flow valve must
be of the “swivel” type.
3. CAUTION: Over tightening of the fittings
in flow valve may cause damage to
valve body
4. Approximately 8" of hose slack must be
realized between the flow valve and
valve stand after the flow valve has been
completely plumbed. If this condition
does not exist after the plumbing has
been completed, removal of valve will
require hoses to be removed at opposite
end of valve.
5. Assembly of valve on stand:
a. Cut a 5" x 5" square opening in floor
board of truck where the valve stand is
to be located.
b. Bolt valve stand halves together forming
a “box” over the 5" x 5" square opening.
NOTE: When bolting valve stand halves
in place, make sure holes in flanges
align with holes in flange plate.*
c. Bolt flange plate to VALVE (Use (2)
1/4" x 3" bolts, lockwashers, etc.)
d. Insert hoses through floor opening and
valve stand and connect appropriate
hoses (see instructions #1 thru #4) to
flow valve.
e. Bolt flange plate to valve
stand flanges.
Download from Www.Somanuals.com. All1M1anuals Search And Download.
DUAL FLOW CONTROL VALVE
62213
Download from Www.Soman1ua2ls.com. All Manuals Search And Download.
PARTS LIST FOR DUAL HYDRAULIC FLOW CONTROL VALVE
(62213)
Item
Part Number
62383
Qty.
2
Description
1
2
3
4
5
6
7
8
-
Screw
62098
2
Handknob
62384
2
Dowel Pin
62385
2
Roll Pin
62386
2
Spring
04105-285-06
04105-285-07
04105-285-08
62099
2
O-Ring, Viton ®
Back-up, Teflon
2
2
O-Ring, Viton ®
Kit, Seal - Consists of Items 6, 7 & 8
Auger Adj. Assy. - 7 GPM
Auger Adj. Assy. -10 GPM
Auger Adj. Assy. - 15 GPM
Auger Adj. Assy. - 20 GPM
Auger Adj. Assy. -25 GPM
Auger Adj. Assy. - 30 GPM
Spinner Adj. Assy. - 5 GPM
Spinner Adj. Assy. - 7 GPM
Spinner Adj. Assy. - 10GPM
Relief Cartridge
9
04105-285-10
04105-285-11
62387
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
2
04105-285-13
04105-285-14
04105-285-15
04105-285-16
62388
10
04105-285-18
62389
11
12
13
14
15
16
17
18
19
20
21
22
23
24
04105-285-20
62100
Gasket
O-Ring, Viton ®
Back-up, Teflon ®
O-Ring, Viton ®
Roll Pin
04105-032-30
62102
04105-285-24
62103
O-Ring (Dump Stem)
Stem (Not Available - Can no longer service)
Plug
04105-032-21
04105-285-26
62390
Setscrew
62391
Handknob
62392
Lever
62393
Bypass Assy.
62104
O-Ring, Viton ®
NOT SHOWN
04105-285-40
62394
Kit, Seal (For Item 11)
Consists of Items: 12, 13, 14 & 15
Kit, Seal
Consists of Items: 6, 7, 8, 12, 13, 14, 15, 17, 23 & 24
Download from Www.Somanuals.com. All1M3anuals Search And Download.
Download from Www.Soman1ua4ls.com. All Manuals Search And Download.
PARTS LIST FOR MDV ENGINE DRIVEN HOPPER ASSEMBLIES
(Carbon Steel)
Item
Part Number
00115-146-01
00115-146-02
00115-146-09
00115-146-10
00115-146-17
00115-146-18
62343
Qty.
1
Description
1
Weld, Hopper 840
1
Weld, Hopper 844
1
Weld, Hopper 940
1
Weld, Hopper 944
1
Weld, Hopper 1040
1
Weld, Hopper 1044
6
1
Weld, Drag Chain, 8' MDV
Weld, Drag Chain, 9' MDV
Weld, Drag Chain, 10' MDV
Bolt, 1/2-13 x 3/4 HH GR5 ZP
Lockwasher, 1/2" Med Split ZP
Bolt, 3/8-16 x 1-1/2 HH GR5 ZP
Nut, 3/8-16 Serrated Flange ZP
Bearing, 1-1/4"
62344
1
62345
1
7
20091
4
8
20329
6
10
12
13
16
17
18
19
20
21
22
23
29
31
33
35
20051
2
04003-806-02
62355
10
2
20525
25
2
Nut, 5/16-18 Serrated Flange ZP
Plate, Front Brg.
62302
20226
8
Bolt, 1/2-13 x 1-3/4 Carriage GR5 ZP
Locknut, 1/2-13 Nyl Ins ZP
Weld, Idler Shaft
20307
8
62370
1
61171
1
Sprocket, Drag Chain
Knob, Hand
61169
1
62300
1
Feedgate, Forming
20353
7
Flatwasher, 3/8" U.S.S. ZP
Weld, Take-up
62304
2
62408
10
2
Nut, 1/2-13 Hex Jam ZP
Shield, Rep. Chain 8’
Shield, Rep. Chain 9’
Shield, Rep. Chain 10'
Instruction Manual MDV (1-739)
Handle
62310
62308
2
62306
2
38
39
40
41
42
43
44
45
46
47
48
49
52
00115-147-00M
62280
1
1
20354
1
Flatwasher, 7/16" U.S.S. ZP
Pin, 1/8" x 1" Cotter
04010-003-02
04003-033-12
20305
1
7
Bolt, 3/8-16 x 3/4 Carriage SS
Locknut, 3/8-16 Nyl Ins ZP
Bar, Pivot
8
62270
1
61204
2
Pin, Master for Chn W/O Cotter
Pin, Cotter Only
04045-025-00
21971
2
2
Decal, Meyer
21932
1
Decal, Serial (w/Pat. Nos.)
Decal, Danger (Conveyor)
Floor, Forming, 8'
62009
2
62292
1
62290
1
Floor, Forming, 9'
62288
1
Floor, Forming, 10'
53
54
55
62335
1
Screw, 3/8-16 x 1-3/16" SLT FL HD
Bolt, 5/16-18 x 3/4 Carriage SS
Weld, Inverted “V” 8'
Weld, Inverted “V” 9'
Weld, Inverted “V”, 10'
V-Belt
04003-032-06
62298
1
1
62296
1
62294
1
56
57
58
59
61
62
63
64
61162
1
61168
1
Cover, Clutch
61176
1
Retainer, Clutch
04003-001-16
62187
4
Bolt, 1/4-20 x 1 HH ZP
Nut, 1/4-20 Serrated Flange
Engine, 10-1/2 HP I/C
Key, 1/4" Sq x 1
4
62133
1
61196
1
61177
1
Pulley, Driver
Download from Www.Somanuals.com. All1M5anuals Search And Download.
PARTS LIST FOR MDV ENGINE DRIVEN HOPPER ASSEMBLIES
(Carbon Steel)Continued
Item
65
Part Number
04003-002-06
61205
Qty.
1
1
5
2
1
2
2
1
1
2
2
2
1
2
1
2
1
1
2
2
1
4
4
2
1
1
4
1
1
1
1
1
3
3
2
1
1
1
2
1
4
1
1
1
2
2
1
1
2
1
1
1
1
1
3
3
1
1
Description
Bolt, 5/16-18 x 1-1/2 HH GR5 ZP
Bolt, “L”
66
67
20352
Flatwasher, 5/16" U.S.S. ZP
Grommet, CA Plug Type (1 1/4")
Solenoid, Grounded
Terminal, Insulated Ring
Connector, 16-14 Insulated Butt
Cable, Battery
68
04093-022-00
61179
69
70
62046
71
62188
73
62040
74
61213
Cable, Starter
75
62395
Spring, Linkage
76
04607-004-00
62191
Clamp, 3/8" Nylon Cable
Screw, #10-24 3/4 HWH TEKS/3
Tie, Nylon 6"
77
78
04607-001-00
61206
79
Rod, Battery
80
04604-017-00
20355
Down Hold
81
Flatwasher, 1/2" U.S.S. ZP
Weld, Shroud
82
00115-140-01
61215
83
Rod, Prop
84
20353
Flatwasher, 3/8" U.S.S. ZP
Pin, 3/32" x 1" Cotter
Decal, Gasoline Only
Bolt, 1/2-13 x 4 Car GR5 PLN
Flatwasher, 7/16" U.S.S. ZP
Pin, 1/8" x 1" Cotter
Bolt, 3/8-16 x 1 Car GR5 ZP
Locknut, 3/8-16 Nyl Ins ZP
Bolt, 3/8-16 x 7/8" HH GR5 ZP
Hose, 3/8" x 13" (1) Wire
Ell. 3/8" 90 Deg. Street
Bolt, 3/8-16 x 1-1/4" Car GR5 ZP
Boot, Batt. Cable, Straight
Boot, Alt. Cable
85
61231
88
04049-199-00
20235
91
94
20354
95
04010-003-02
20202
96
97
20305
98
20048
99
04120-078-01
04110-006-03
20203
100
101
104
105
106
107
109
111
112
113
115
116
117
118
119
120
121
124
125
126
127
128
129
130
131
132
133
134
135
136
62105
62106
04003-081-04
20327
Screw, 5/16-18 x 3/4 Soc Cap
Lockwasher, 3/8" Med Split ZP
Tie, Nylon 6"
04607-001-00
62174
Assy, Plate Actuator
Assy, Control Cable
Dia. Wiring/Instructions
Trim, Vinyl
62169
00113-668-00
04093-021-00
20203
Bolt, 3/8-16 x 1-1/4" Car GR5 ZP
Bolt, 5/16-18 x 1 Car SS
Decal, Caution
20600
62007
62354
Wiper, Chain
61163
Bearing, 1-1/4"
62284
Sprocket, Drive w/Set Screws
Key, 1/4" SQ x 2"
62000
61178
Assy, Gearbox
61202
Snap Ring, External
Key, 1/4" x 7/8" Woodruff
Washer
61201
00107-679-00
61161
Pulley, Driven
61167
Clutch, Electric
00108-771-00
04003-002-09
20326
Washer, Flat
Bolt, 5/16-18 x 2 HH GR5 ZP
Lockwasher, 5/16" Med Split ZP
Screw, 5/16-18 x 3/4 Soc Cap
Collar, Set 1" Per Print
Sprocket, 41B13
04003-081-04
04001-001-01
61156
Download from Www.Soman1ua6ls.com. All Manuals Search And Download.
PARTS LIST FOR MDV ENGINE DRIVEN HOPPER ASSEMBLIES
(Stainless Steel)
Item
Part Number
00115-146-05
00115-146-06
00115-146-13
00115-146-14
00115-146-21
00115-146-22
62343
Qty.
1
1
1
1
1
1
1
1
1
4
6
2
10
2
25
2
8
8
1
1
1
2
7
2
10
2
2
2
1
1
1
1
7
8
1
2
2
2
1
2
1
1
1
1
4
8
1
1
1
1
1
1
4
4
1
1
1
3
1
5
2
Description
Weld, Hopper 840, S3
Weld, Hopper 844, S3
Weld, Hopper 940, S3
Weld, Hopper 944, S3
Weld, Hopper 1040, S3
Weld, Hopper 1044, S3
Weld, Drag Chain, 8' MDV
Weld, Drag Chain, 9' MDV
Weld, Drag Chain, 10' MDV
Bolt, 1/2-13 x 3/4 HH SS
Lockwasher, 1/2" Med Split SS
Bolt, 3/8-16 x 1 1/2 HH SS
Nut, 3/8-16 Serrated Flange SS
Bearing, 1-1/4"
1
6
62344
62345
7
04003-005-56
04004-001-16
04003-003-28
04003-806-12
62355
8
10
12
13
16
17
18
19
20
21
22
23
29
31
33
35
04003-806-13
62302
Nut, 5/16-18 Ser Flange SS
Plate, Front Brg., S3
04003-034-19
04003-804-07
62370
Bolt, 1/2-13 x 1-3/4 Car NK SS
Locknut, 1/2-13 Nyl Ins SS
Weld, Idler Shaft
61171
Sprocket, Drag Chain
Knob, Hand
61169
62301
Feedgate, Forming, S3
Flatwasher, 3/8" U.S.S. SS
Weld, Take-up
04004-002-20
62304
62336
Nut, 1/2-13 Hex Jam SS
Shield, Rep. Chain 8 Ft, S3
Shield, Rep. Chain 9 Ft, S3
Shield, Rep. Chain 1OFt, S3
Instruction Manual MDV
Handle
62311
62309
62307
38
39
40
41
42
43
44
45
46
47
48
49
50
52
00115-147-00
62280
04004-002-32
04010-003-02
04003-033-12
04003-804-08
62270
Flatwasher, 7/16" U.S.S. SS
Pin, 1/8" x 1" Cotter
Bolt, 3/8-16 x 3/4 Car SS
Locknut, 3/8-16 Nyl Ins SS
Bar, Pivot
62346
Pin, Master for Chn W/O Cotter
Pin, Cotter Only
04045-025-00
21971
Decal, Meyer
21932
Decal, Serial (w/Pat.Nos.)
Decal, Danger (Conveyor)
Decal, Stainless Steel
Floor, Forming, 8', S3
Floor, Forming, 9', S3
Floor, Forming, 10', S3
Screw, 3/8-16 x 1- 3/16" Slt FI SS
Bolt, 5/16-18 x 3/4 Car SS
Weld, Inverted “V” 8', S3
Weld, Inverted “V” 9', S3
Weld, Inverted “V” 10', S3
V-Belt
04049-182-00
04049-229-00
62293
62291
62289
53
54
55
04003-025-02
04003-032-06
62299
62297
62295
56
57
58
59
61
62
63
64
65
66
67
68
61162
61168
Cover, Clutch
61176
Retainer, Clutch
04003-001-16
04003-806-15
62133
Bolt, 1/4-20 x 1” H H SS
Nut, 1/4-20 Ser Flange SS
Engine, 10 1/2 HP I/C
Key, 1/4" SQ x 1
62397
61177
Pulley, Driver
04003-002-21
61205
Bolt, 5/16-18 x 1-1/2 HH SS
Bolt, “L”
04004-002-25
04093-022-00
Flatwasher, 5/16" U.S.S. SS
Grommet, CA Plug Type (1-1/4")
Download from Www.Somanuals.com. All1M7anuals Search And Download.
PARTS LIST FOR MDV ENGINE DRIVEN HOPPER ASSEMBLIES
(Stainless Steel)
Item Part Number Qty.
Description
69
70
61179
62046
1
2
2
1
1
2
2
2
1
2
1
2
1
1
2
2
1
4
4
2
1
1
4
1
1
1
1
1
3
3
2
1
1
1
1
4
1
1
1
2
2
1
1
2
1
1
1
1
1
3
3
1
1
Solenoid, Grounded
Terminal, Insulated Ring
Connector, 16-14 Insulated Butt
Cable, Battery
71
62188
73
62040
74
61213
Cable, Starter
75
62395
Spring, Linkage
76
04607-004-00
04002-069-02
04607-001-00
61206
Clamp, 3/8" Nylon Cable
Screw, #10-24 x 3/4 HWH TEKS/3 SS
Tie, Nylon 6"
77
78
79
Rod, Battery
80
04604-017-00
04004-002-22
00115-140-02
61215
Down, Hold
81
Flatwasher, 1/2" U.S.S. SS
Weld, Shroud, S3
82
83
Rod, Prop
84
04004-002-20
61231
Flatwasher, 3/8" U.S.S.SS
Pin, 3/32" x 1" Cotter
Decal, Gasoline Only
Bolt, 1/2-13 x 4 Car GR5 Pin
Flatwasher, 7/16" SS
Pin, 1/8" x 1" Cotter
Bolt, 3/8-16 x 1" Car SS
Locknut, 3/8-16 Nyl Ins SS
Bolt, 3/8-16 x 3/4 HH SS
Hose, 3/8" x 13" (1) Wire
Ell., 3/8" 90 Deg Street
Bolt, 3/8-16 x 1-1/4" Car SS
Boot, Batt. Cable, Straight
Boot, Alt. Cable
85
88
04049-199-00
20235
91
94
04004-002-32
04010-003-02
04003-033-03
04003-804-08
04003-003-24
04120-078-01
04110-006-03
04003-033-05
62105
95
96
97
98
99
100
101
104
105
106
107
109
111
112
113
116
117
118
119
120
121
124
125
126
127
128
129
130
131
132
133
134
135
136
62106
04003-081-04
04004-001-14
04607-001-00
62174
Screw, 5/16-18 x 3/4" Soc Cap
Lockwasher, 3/8" Med Split SS
Tie, Nylon 6"
Assy, Plate Actuator
Assy, Control Cable
Dia. Wiring/Instructions
Bolt, 3/8-16 x 1-1/4 Car SS
Bolt, 5/16-18 x 1 Car SS
Decal, Caution
62169
00113-668-00
04003-033-05
04003-032-04
62007
62354
Wiper, Chain
61163
Bearing, 1-1/4"
62284
Sprocket, Drive w/Set Screws
Key, 1/4" Sq. x 2"
62000
61178
Assy, Gearbox
61202
Snap Ring, External
Key, 1/4" x 7/8" Woodruff
Washer
61201
00107-679-00
61161
Pulley, Driven
61167
Clutch, Electric
00108-771-00
04003-002-09
20326
Washer, Flat
Bolt, 5/16-18 x 2 HH GR5 ZP
Lockwasher, 5/16" Med Split ZP
Screw, 5/16-18 x 3/4 Soc Cap
Collar, Set 1" Per Print
Sprocket, 41B13
04003-081-04
04001-001-01
61156
Download from Www.Soman1ua8ls.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All1M9anuals Search And Download.
49
47
!
DANGER
R
25
26
19
18
62
21
27
28
29
11
20
13
68
34
10
29
12
29
42
22
16
60
53
43
29
55
52
57
54
16
42
12
18
31
33
17
58
19
40
41
59
43
39
48
44
!
DANGER
R
Oo44112
T
H
I
S
M
A
C
H
I
N
E
M
A
Y
B
E
C
O
V
E
R
E
D
B
Y
O
N
E
R
M
O
E
O
F
T
H
E
S
PATNTS
3
,
1
8
9
,
3
5
5
3
,
3
3
2
,
6
9
1
3,510,066
4,342,1634,353,177 4,549,697
SERIAL
3,851,804
38 ITEMS NOT SHOWN:
INSTRUCTION MANUAL
!
CAUTION
50
1
(PACKED INSIDE BAG & SHIPING CARTON)
49
61
51
2812
30
56
67
66
42
43
23
7
35
63
6
45 12
46
64
65
8
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST FOR MDV HYDRAULIC HOPPER ASSEMBLIES
(Carbon Steel)
Item Part Number
00115-146-01
00115-146-02
00115-146-09
00115-146-10
00115-146-17
00115-146-18
Qty. Description
1
1
1
1
1
1
1
1
1
1
4
4
2
4
Weld, Hopper 840
Weld, Hopper 844
Weld, Hopper 940
Weld, Hopper 944
Weld, Hopper 1040
Weld, Hopper 1044
5
6
61201
62343
62344
Key, 1/4" x 7/8" Woodruff
Weld, Drag Chain, 8' MDV
Weld, Drag Chain, 9' MDV
Weld, Drag Chain, 10' MDV
Bolt, 1/2-13 x 3/4 HH GR5 ZP
Lockwasher, 1/2" Med Split ZP
Bolt, 3/8-16 x 1-1/2 HH GR5 ZP
Lockwasher, 3/8" Med Split ZP
62345
20091
7
8
20329
20051
10
11
12
13
16
17
18
19
20
21
22
23
25
26
27
28
29
30
31
33
34
35
20327
04003-806-02
62355
10 Nut, 3/8-16 Serrated Flange ZP
Bearing, 1-1/4"
29 Nut, 5/16-18 Ser Flange ZP
Plate, Front Brg.
2
04003-806-13
62302
20226
2
10 Bolt, 1/2-13 x 1-3/4 Car GR5 ZP
10 Locknut, 1/2-13 Nyl Ins ZP
20307
62370
1
1
1
2
1
1
4
4
Weld, Idler Shaft
Sprocket, Drag Chain
Knob, Hand
61171
61169
62300
62398
Feedgate, Forming
Motor, Hydraulic (AA)
Plate, Motor Mtg.
62399
62202
Bushing, 3/8" I.D. x 5/8" O.D.
Bolt, 3/8-16 x 1 HH GR5 ZP
20049
20353
10 Flatwasher, 3/8" U.S.S. ZP
62073
62304
62408
1
2
Coupling, Shaft
Weld, Take-up
10 Nut, 1/2-13 Hex Jam ZP
04007-005-04
62310
62308
2
2
2
2
1
1
1
1
8
6
1
2
2
2
1
2
1
1
1
4
8
Setscrew. 1/4-20 x 3/8" AL HD
Shield, Rep. Chain 8’
Shield, Rep. Chain 9’
Shield, Rep. Chain 10'
Instruction Manual MDV
Handle
62309
38
39
40
41
42
43
44
45
46
47
48
49
52
-----------------
00110-817-00
20354
Flatwasher, 7/16" U.S.S. ZP
Pin, 1/8" x 1" Cotter
04010-003-02
04003-033-12
20314
Bolt, 3/8-16 x 3/4 Car SS
Locknut, 3/8-16 Nyl Ins ZP
Bar, Pivot
62270
61204
Pin, Master for Chn W/O Cotter
Pin, Cotter Only
Decal, Meyer
04045-025-00
21971
21932
Decal, Serial (w/Pat.Nos.)
Decal, Danger (Conveyor)
Floor, Forming, 8'
62009
62292
62290
62288
Floor, Forming, 9'
Floor, Forming, 10'
53
54
62335
00400-032-06
Screw, 3/8-16 x 1-3/16" SILT FIL HD
Bolt, 5/16-18 x 3/4 Car SS
Download from Www.Somanuals.com. All2M1anuals Search And Download.
PARTS LIST FOR MDV HYDRAULIC HOPPER ASSEMBLIES
(Carbon Steel)
Item
55
Part Number
62298
62296
Qty. Description
1
1
1
1
1
4
1
2
1
2
2
1
1
1
Weld, Inverted “V” 8'
Weld, Inverted “V” 9'
Weld, Inverted “V” 10'
Guard, Shaft
62294
56
59
60
61
62
63
64
65
66
67
68
62314
20203
Bolt, 3/8-16 x 1-1/4 Car GR5 ZP
Bolt, 5/16-18 x 1 Car SS
Decal, Caution
04003-032-04
62007
04004-002-22
62400
Flatwasher, 1/2" U.S.S. SS
Bearing, 1-1/4"
62284
Sprocket Drive 2/Set Screws
Key, 1/4" SQ. x 2"
62401
62402
Assy, Gearbox
61156
Sprocket, 41B13
04009-001-00
Key, 1/4" x 7/8" Woodruff
Download from Www.Soman2ua2ls.com. All Manuals Search And Download.
PARTS LIST FOR MDV HYDRAULIC HOPPER ASSEMBLIES
(Stainless Steel)
Item Part Number Qty .Description
1
00115-146-05
00115-146-06
00115-146-13
00115-146-14
00115-146-21
00115-146-22
61201
1
1
1
1
1
1
1
1
1
1
4
4
2
4
10
2
29
2
10
10
1
1
1
2
1
1
4
4
10
1
2
10
2
2
2
2
1
1
1
Weld, Hopper 840, S3
Weld, Hopper 844, S3
Weld, Hopper 940, S3
Weld, Hopper 944, S3
Weld, Hopper 1040, S3
Weld, Hopper 1044, S3
Key, 1/4" x 7/8" Woodruff
Weld, Drag Chain, 8' MDV
Weld, Drag Chain, 9' MDV
Weld, Drag Chain, 10' MDV
Bolt, 1/2-13 x 3/4 HH SS
Lockwasher, 1/2" Med Split SS
Bolt, 3/8-16 x 1-1/2 HH SS
Lockwasher, 3/8" Med Split SS
Nut, 3/8-16 Serrated Flange SS
Bearing, 1-1/4"
Nut, 5/16-18 Ser Flange SS
Plate, Front Brg., S3
Bolt, 1/2-13 x 1-3/4 Car NK SS
Locknut, 1/2-13 Nyl Ins SS
Weld, Idler Shaft
Sprocket, Drag Chain
Knob, Hand
Feedgate, Forming,
5
6
62343
62344
62345
7
8
04003-005-56
04004-001-16
04003-003-28
04004-001-14
04003-806-12
62355
04003-806-13
62303
04003-034-19
04003-804-07
62370
10
11
12
13
16
17
18
19
20
21
22
23
25
26
27
28
29
30
31
33
34
35
61171
61169
62301
62398
62368
62339
Motor, Hydraulic (AA)
Plate, Motor Mtg., S3
Bushing, Spacer, S3
Bolt, 3/8-16 x 1 HH SS
Flatwasher, 3/8" U.S.S. SS
Coupling, Shaft
04003-003-20
04004-002-20
62073
62304
62336
04007-005-04
62311
62309
62307
00115-147-00
62280
04004-002-32
04010-003-02
04003-033-12
04003-804-08
62270
Weld, Take-up
Nut, 1/2-13 Hex Jam
Setscrew. 1/4-20 x 3/8" AL HD
Shield, Rep. Chain 8’
Shield, Rep. Chain 9’
Shield, Rep. Chain 10'
Instruction Manual MDV
Handle
Flatwasher, 7/16" U.S.S. SS
Pin, 1/8" x 1" Cotter
Bolt, 3/8-16 x 3/4 Car
Locknut, 3/8-16 Nyl Ins SS
Bar, Pivot
38
39
40
41
42
43
44
45
46
47
48
49
50
52
1
8
6
1
61204
2 Pin,MasterforChnW/OCotter
04045-025-00
21971
21932
04049-182-00
04049-229-00
62293
62291
62289
04003-025-02
04003-032-06
62299
2
2
1
2
1
1
1
1
1
1
1
1
1
Pin, Cotter Only
Decal, Meyer
Decal, Serial (w/Pat. Nos.)
Decal, Danger (Conveyor)
Decal, Stainless Steel
Floor, Forming, 8 Ft., S3
Floor, Forming, 9 Ft. S3
Floor, Forming, 10 Ft. , S3
Screw, 3/8-16 x 1-3/16" SLT FL SS
Bolt, 5/16-18 x 3/4 Car SS
Weld, Inverted “V” 8 FT. S3
Weld, Inverted “V” 9 FT. S3
Weld, Inverted “V” 10 FT. S3
53
54
55
62297
62295
Download from Www.Somanuals.com. All2M3anuals Search And Download.
PARTS LIST FOR MDV HYDRAULIC HOPPER ASSEMBLIES
(Stainless Steel)
Item
56
57
58
59
60
61
62
63
64
65
66
67
68
Part Number
62315
62354
Qty. Description
Guard, Shaft, S3
1
1
Wiper, Chain
62395
2
Spring, Linkage
04003-033-05
04003-032-04
62007
1
Bolt, 3/8-16 x 1-1/4 Car SS
Bolt, 5/16-18 x 1 Car SS
Decal, Caution
4
1
2
1
2
2
1
1
1
04004-002-22
61163
Flatwasher, 1/2" U.S.S. SS
Bearing, 1-1/4"
62284
Sprocket, Drive W/Set Screws
Key, 1/4" SQ. x 2"
62000
61178
Assy, Gearbox
61156
Sprocket, 41B13
61201
Key, 1/4" x 7/8" Woodruff
Download from Www.Soman2ua4ls.com. All Manuals Search And Download.
Notes
Download from Www.Somanuals.com. All2M5anuals Search And Download.
28
27
25
26
4
7
21
18
9
19 24
17
5
22
24
9
7
DETAIL-A
8
2
16
DANGER
1
15
23
CAUTION
24
DETAIL-A
30
25
29
14 13
12
14
5
6
10
3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST FOR HYDRAULIC SPINNER ASSEMBLY
(Carbon Steel)
Item Part Number
1
2
Qty. Description
62312
62057
62146
1
1
1
1
2
2
8
2
8
1
1
1
3
Weld, Spinner Frame
Shaft, Spinner (Long)
Disc, Poly Spinner 13"
Motor, Hydraulic (AA)
Bolt, 3/8-16 x 2” HH GR5 ZP
Locknut, 3/8-16 Cen Lock ZP
Bolt, 3/8-16 x 3/4 HH GR5 ZP
Bearing, 1" Tapped Base
Lockwasher, 3/8" Med Split ZP
Weld, Baffle, L.H.
3
4
60324
5
6
7
8
04003-003-06
04003-807-09
04003-003-01
62356
9
20327
61181
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
27
28
29
30
61182
61183
62313
61232
62007
62006
62073
62201
62202
Weld, Baffle, R.H.
Weld, Baffle, Rear
Bar, Link, S3
12 Keeper, Hairpin Small
1
1
1
1
4
1
1
2
Decal, Caution
Decal, Danger (Spinner)
Coupling, Shaft
Plate, Motor Mtg.
Bushing, 3/8" I.D. x 5/8" O.D.
Bag, Hardware
00115-152-00
04031-017-00
62358
Key, 1/4" SQ x 3" Straight
Spring, Compression
20353
62331
62305
10 Flatwasher, 3/8" U.S.S. ZP
1
2
6
6
2
1
Weld, Handle
Plate, Baffle
Nut, 1/4-20 Ser. Flange SS
Bolt, 1/4-20 x 1/2" Car SS
Pin, 1/8" x 1" Cotter SS
Weld, Handle
04003-806-15
04003-031-06
04010-016-01
62333
PARTS LIST FOR HYDRAULIC SPINNER ASSEMBLY
(Stainless Steel)
Item Part Number
1
2
Qty. Description
00115-148-02
62057
62146
1
1
1
1
2
2
8
2
8
1
1
1
3
Weld, Spinner Frame, S3
Shaft, Spinner (Long)
Disc, Poly Spinner 13"
Motor, Hydraulic (AA)
Bolt, 3/8-16 x 2” HH SS
Locknut, 3/8-16 Cen Lock SS
Bolt, 3/8-16 x 3/4 HH SS
Bearing, 1" Tapped Base
Lockwasher, 3/8" Med Split SS
Weld, Baffle, L.H., S3
Weld, Baffle, R.H., S3
Weld, Baffle, Rear, S3
Bar, Link, S3
3
4
60324
5
6
7
8
04003-003-29
04003-807-18
04003-003-24
62356
9
04004-001-14
00104-811-01
62272
62275
62313
04011-001-05
62007
62006
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
27
28
29
30
12 Keeper, Hairpin #7 SS
1
1
1
1
4
1
1
2
Decal, Caution
Decal, Danger (Spinner)
Coupling, Shaft
Plate, Motor Mtg., S3
Bushing, Spacer, S3
Bag, Hardware
62073
62201
62239
00115-152-00
04031-017-00
62358
04004-002-20
00115-545-02
00115-127-02
04003-806-15
04003-031-06
04010-016-01
00115-580-02
Key, 1/4" SQ x 3" Straight
Spring, Compression
10 Flatwasher, 3/8" U.S.S. SS
1
2
6
6
2
1
Weld, Handle
Plate, Baffle, S3
Nut, 1/4-20 Ser. Flange SS
Bolt, 1/4-20 x 1/2" Car SS
Pin, 1/8" x 1 “ Cotter SS
Weld, Handle L.H., S3
Download from Www.Somanuals.com. All2M7anuals Search And Download.
26
25
23
24
17
18
8
22
9
7
DETAIL-A
16
2
DANGER
1
15
19
CAUTION
22
DETAIL-A
20
27
23
4
14 13
12
14
5
6
10
3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST FOR ENGINE DRIVEN SPINNER ASSEMBLY
(Carbon Steel)
Item Part Number
62312
Qty. Description
1
1
1
2
1
1
4
2
4
1
1
1
3
Weld, Spinner Frame
2
3
62057
62146
Shaft, Spinner (Long)
Disc, Poly Spinner 13"
Pin, 1/8" x 1" Cotter SS
Bolt, 3/8-16 x 2 HH GR5 ZP
Locknut, 3/8-16 Cen Lock ZP
Bolt, 3/8-16 x 3/4 HH GR5 ZP
Bearing, 1" Tapped Base
Lockwasher, 3/8" Med Split ZP
Weld, Baffle, L.H.
4
5
6
7
04010-016-01
04003-003-06
04003-807-09
04003-003-01
62356
8
9
20327
61181
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
61182
61183
62313
61232
62007
62006
61196
61156
62358
Weld, Baffle, R.H.
Weld, Baffle, Rear
Bar, Link, S3
12 Keeper, Hairpin Small
1
1
1
1
2
1
6
1
2
6
1
1
Decal, Caution
Decal, Danger (Spinner)
Key, 1/4" SQ x 1
Sprocket, 41 B1 3
Spring, Compression
Bag, Hardware
Flatwasher, 3/8" U.S.S. ZP
Weld, Handle
Plate, Baffle
Nut, 1/4-20 Ser Flange SS
Bolt, 1/4-20 x 1/2" Car SS
Weld, Handle
00115-165-00
20353
62331
62305
04003-806-15
04003-031-06
62333
PARTS LIST FOR ENGINE DRIVEN SPINNER ASSEMBLY
(Stainless Steel)
Item Part Number
1
2
Qty. Description
00115-148-02
62057
62146
1
1
1
2
1
1
4
2
4
1
1
1
3
Weld, Spinner Frame, S3
Shaft, Spinner (Long)
Disc, Poly Spinner 13"
Pin, 1/8" x 1" Cotter SS
Bolt, 3/8-16 x 2 HH SS
Locknut, 3/8-16 Cen Lock SS
Bolt, 3/8-16 x 3/4 HH SS
Bearing, 1" Tapped Base
Lockwasher, 3/8" Med Split SS
Weld, Baffle, L.H., S3
Weld, Baffle, R.H., S3
Weld, Baffle, Rear, S3
Bar, Link, S3
3
4
5
6
7
04010-016-01
04003-003-29
04003-807-18
04003-003-24
62356
8
9
04004-001-14
00104-811-01
62272
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
62275
62313
61232
62007
62006
61196
61156
62358
12 Keeper, Hairpin Small
1
1
1
1
2
1
6
1
2
6
6
1
Decal, Caution
Decal, Danger (Spinner)
Key, 1/4" SQ x 1
Sprocket, 41 B1 3
Spring, Compression
Bag, Hardware
Flatwasher, 3/8" U.S.S. SS
Weld, Handle, S3
Plate, Baffle, S3
Nut, 1/4-20 Ser. Flange SS
Bolt, 1/4-20 x 1/2" Car SS
Weld, Handle L.H., S3 .
00115-165-00
04004-002-20
00115-545-02
00115-127-02
04003-806-15
04003-031-06
00115-580-02
Download from Www.Somanuals.com. All2M9anuals Search And Download.
ELECTRIC CONTROLS
PARTS & SCHEMATIC
(Honda)
GREY WIRE
THESE CONNECTIONS TO BE SECURED BEHIND PLATE
BROWN
CONNECT TO KILL WIRE FROM ENGINE
BROWN
GREEN
WHITE WIRE
BLACK
LINKAGE ROD 5
6
4 ACTUATOR
GRD
GREEN
MOUNTING SCREW HERE
AT ASSEMBLY
WHT
BLACK
RED
WHT
RED
**WHITE IS SECURED UNDER MOUNTING
SCREW USED IN STEP 1B
FUSE HOLDER / W FUSE
POSITIVE FROM BATTERY
3
ON ENGINE
RED
SOLENOID
YELLOW
BLUE
TO CENTER TAB ON SOLENOID
YELLOW
1
BLUE
TO CLUTCH POWER WIRE
CLUTCH
(7) CONDUCTOR CABLE
& PLUG
2
GROUND
AFTER INSTALLATION
COIL CABLE AND SECURE TO TOP OF ENGINE NEATLY
WIRING AT THE ENGINE
NOTE: The plug is wired to the cable as indicated on the connector.
(That is; red to red, black to black, etc.)
Item
Part No.
00115-189-00
62119
Qty.
Description
1
2
3
4
5
6
Assy, Control Cable
Plug, 7 Conductor
Conductor-7, 14 ga. 103"
Actuator, Linear
Rod, Linkage
Plate, Throttle
1
1
1
1
1
1
62170
62081
62324
62322
62323
Assy, Throttle Plate
(Includes Items 4, 5, & 6)
Download from Www.Soman3ua0ls.com. All Manuals Search And Download.
ELECTRIC CONTROLS
PARTS & SCHEMATIC
(Briggs & Stratton)
GREY WIRE
INSTALL KILL CONNECTION FROM ENGINE HERE
THESE CONNECTIONS TO BE SECURED BEHIND PLATE
BROWN
CONNECT TO KILL SWITCH TAB
BROWN
6
GREEN
WHITE WIRE
BLACK
LINKAGE ROD 5
RED WIRE FROM ENGINE
ACTUATOR
4
GRD
MOUNTING SCREW HERE
AT ASSEMBLY
GREEN
WHT
BLACK
RED
WHT
RED
WHITE IS SECURED UNDER MOUNTING
SCREW USED IN STEP 2B
**
FUSE HOLDER / W FUSE
3
POSITIVE FROM BATTERY
RED
SOLENOID
YELLOW
TO CENTER STUD ON SOLENOID
YELLOW
BLUE
1
FROM STARTER
BLUE
TO CLUTCH POWER WIRE
7) CONDUCTOR CABLE
& PLUG
CLUTCH
2
GROUND
AFTER INSTALLATION
COIL CABLE AND SECURE TO TOP OF ENGINE NEATLY
WIRING AT THE ENGINE
NOTE: The plug is wired to the cable as indicated on the connector.
(That is; red to red, black to black, etc.)
Item
Part No.
62169
62119
62170
62081
62181
62172
Qty.
1
Description
1
2
3
4
5
6
Assy, Control Cable
Plug, 7 Conductor
Conductor-7, 14 ga. 103"
Actuator, Linear
Rod,Linkage
1
1
1
1
1
Plate, Throttle
Download from Www.Somanuals.com. All3M1anuals Search And Download.
CONTROL BOX
3
MOUNTING
TABS
1
CHOKE
START
HI
ON
2
2
LO
CONV.
OFF
4
RED LENSE
5
6
14
DOUBLE CONNECTORS
YELLOW
YELLOW
YELLOW
YELLOW
YELLOW
BLUE
11
STRAIN RELIEF BUSHING
11
12
10
7
BLUE
BLUE
BLUE
BLUE
7
INSERT THIS END THROUGH
ENCLOSURE
16
8
18
YELLOW
GREEN
RED
GREEN
20
BLUE
GREEN
RED
BROWN
GREEN
BLACK
BROWN
BLACK
BROWN
BROWN
RED
RED
15
BROWN
RED
RED
WHITE
BLACK
BLACK
WHITE
WHITE
WHITE
WHITE
BROWN
BROWN
17
Download from Www.Soman3ua2ls.com. All Manuals Search And Download.
PARTS LIST FOR CONTROL PANEL ASSEMBLY
(62267)
Item
1
Part Number
62150
Qty.
1
Description
Enclosure
2
62151
2
Panel, End
3
62152
1
Panel, Middle
4
62153
1
Switch, START/CONV
Switch, Choke HI/LO
Switch, ON/OFF
5
62154
1
6
62155
1
7
62156
3
Conn., double M/FM
Assembly, Cable
8
62157
1
10
11
12
14
15
16
17
18
N/S
N/S
N/S
62158
1
Enclosure, Back Panel
#8 x 1/2 SM SLT HWH SCR
Strain Relief
04002-059-04
62160
4
1
62161
1
Jump Wire, 14 Ga., BLUE 3"
Jump Wire, 14 Ga., BROWN 5.5"
Jump Wire, 14 Ga., RED 4"
Jump Wire, 14 Ga., BROWN 3"
Jump Wire, 14 Ga., RED 3"
Socket, 7 Conductor
Bracket Mounting (included in Kit: use optional)
Boot, Cable
62162
1
62163
1
62164
1
62165
1
62122
1
62166
1
62149
1
NOTE: The conductor socket (not shown ) is wired to the cable as indicated on the socket.
(That is; red to red, black to black, etc.)
Download from Www.Somanuals.com. All3M3anuals Search And Download.
PARTS LIST FOR HYDRAULIC MOTOR
(60324)
Item
1
Part Number
Qty.
4
Description
20644
Screw, 5/16" - 24 x 7/8" Cap
Seal
2
1
3
62404
1
Flange, Mounting (4 Bolt)
Seal, O-Ring
4
5
04101 035 05
1
Race, Bearing
6
Seal, O-Ring
7
04101 035 07
04009 002 02
04101 035 09
04101 035 10
1
1
1
1
Bearing, Thrust Needle
Key, 1/4" x 1 “ Woodruff
Shaft, Output
8
9
10
11
12
Housing
Seal, O-Ring n
04101 035 12
04101 037 12
04101 035 13
20647
1
1
1
4
4
1
1
1
7
Drive (For 04101 035 00)
Drive (For 04101 037 00)
Plate, Spacer
13
14
Screw, 5/16" - 24 x 1-1/2" Cap
Screw, 5/16" - 24 x 1-3/4" Cap
Gerotor Set (For 04101 035 00)
Gerotor Set (For 04101 037 00)
Cap, End
20648
15
04101 035 15
04101 037 15
62405
17
18
20
21
04101 035 18
Washer, Seal
04101 035 21
62406
1
1
1
Repaired Motor (for 04101 035 00)
Seal Kit (Char-Lynn)
62359
Seal Kit (White)
Download from Www.Soman3ua4ls.com. All Manuals Search And Download.
PARTS LIST FOR DURST GEAR BOX ASSEMBLY (61178)
Item
Part No.
Qty.
Description
1
2
62033
62034
62035
62036
62025
62022
62019
62026
62027
62020
62028
62037
62032
62029
62024
61166
62030
62016
62017
62236
62031
62023
62018
62021
1
1
Housing
Cover
3
1
Worm Gear - Bronze
Worm
Bearing Cone
4
1
5
2
6
2
Bearing Cone
7
4
Bearing Cup
8
1
Snap Ring Input
Snap Ring Output
Snap Ring
9
1
10
11
12
*13
14
15
16
17
18
19
20
21
22
23
24
4
4
Capscrew, 3/8" x 3/4" H.H.
Shaft-Input
1
1
Shaft-Output
1
Woodruff Key - Hard
Woodruff Key - Hard
Seal Input
1
1
1
Seal Output
1
Plug, 1/8" - 27 NPTF
Plug, Level, 3/8" - 18 NPTF
Zerk, 1/4" - 28 NF
Gasket, Cover (Not Shown)
Plug, Vent, 1/8" - 27 NPTF
Cap
1
1
1
1
2
A/R
Shim (Not Shown)
Download from Www.Somanuals.com. All3M5anuals Search And Download.
Optional Hopper Top Screens
STANDARD HOPPER TOP SCREENS
Item
Part Number
62258
Qty.
Description
1
4
2
4
Weldment, Screen (57.125" X 34") (10 ft Unit)
Weldment, Screen (9 ft. Unit)
62558 & 62556
62256
Weldment, Screen (45.125" x 34") (8 ft. Unit)
OPTIONAL HOLD DOWN KIT
(62259)
Item
Part Number
04068-001-00
00100-234-00
20095
Qty.
2
Description
1
2
3
4
5
6
Binder, Chain
2
Hook, Hold Down
2
Bolt, 1/2-13 x 1 1/2 HH GR5 ZP
Nut, 1/2-13 Hex ZP
04003-801-11
20329
2
2
Lockwasher, 1/2" Med Split ZP
Flatwasher, 1/2" U.S.S. ZP
20355
2
PARTS LIST FOR SHIPPING CARTON
(62555)
Item
Part Number
62350
Qty.
1
Description
1
2
3
4
5
6
7
Chain, Roller #41 (53 LINKS)
Bag, Hardware
00115-667-00
00107-662-00
62334
1
1
Instruction Package (Briggs & Stratton)
Panel, Control
1
62166
1
Bracket, Mounting
62519
1
Cable, 7 Pin (Front Half)
Grease, Dielectric
04540-013-01
1
Download from Www.Soman3ua6ls.com. All Manuals Search And Download.
ONE YEAR WARRANTY
ING SNOW IS ONE EXAMPLE OF AN ABUSE
AND MISUSE OF THE PRODUCT.
WARRANTY SERVICE
Meyer Products promises to the consumer to
repair or, at Meyer Products' option, to replace
any part of this Meyer Spreader except
expendable parts such as pins, spreader fins,
and other normal wear items, which proves to
be defective in workmanship or material under
normal use for a period of one year from the
date of delivery to the original purchaser.
During this one year, Meyer Products will
provide, to the consumer, through its Distribu-
tor / Sub-Distributor network, all parts
necessary to correct such defects free of
charge. Labor costs incurred for any repairs
on this piece of equipment will be the responsi-
bility of the consumer. Faulty parts will be
repaired or replaced by the Distributor / Sub-
Distributor where that particular piece of
equipment was purchased. Any cost incurred
in returning the product to the Distributor / Sub-
Distributor is the responsibility of the con-
sumer.
In order to obtain service under this warranty,
the consumer must return this Meyer product
to the Distributor / Sub-Distributor from whom
the product was purchased or to any other
Meyer Products Distributor / Sub-Distributor,
transportation and freight charges prepaid.
Only Meyer Products Distributor / Sub-
Distributors are authorized to perform the
obligations under these warranties. For the
address and telephone number of the
Distributor / Sub-Distributor nearest you,
check the telephone directory or you may write
to the warrantor at the address below.
GENERAL
It is the responsibility of the consumer to
establish the warranty period by verifying the
original delivery date. A bill of sale, cancelled
check or some other appropriate payment
record may be kept for that purpose. It is
recommended, but not required, that the
consumer verify the original delivery date by
immediately returning the attached Warranty
Registration Card. No person is authorized to
change this warranty or to create any warranty
other than that set forth herein. This warranty
gives you specific legal rights and you may
also have other rights which vary from state to
state.
The gasoline engine used in this product is
covered by its own warranty as provided by
the engine manufacturer. A copy of this
warranty is included with the engine.
EXCLUSIONS
IN NO EVENT SHALL MEYER PRODUCTS
BE LIABLE FOR SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR FOR
DAMAGES RESULTING FROM LACK OF
NECESSARY MAINTENANCE, FROM
MISUSE, ABUSE, ACTS OF GOD, ALTER-
ATION OF THE MEYER PRODUCT, OR
FROM USE OF PARTS OR HYDRAULIC
FLUID NOT SUPPLIED BY MEYER PROD-
UCTS. USE OF THE MEYER SNOWPLOW
FOR ANY PURPOSE OTHER THAN PLOW-
Meyer Products
18513 Euclid Avenue
Cleveland, Ohio 44112
Phone (216) 486-1313
Fax (216) 486-3073
E-Mail [email protected]
In order to validate this warranty, please complete this card and mail it.
Name: ______________________________________________________
Address: ______________________________________________________
______________________________________________________
Spreader Model: ________________ Serial No.: ____________________
Installation Date:__________ Purchased From: ____________________
Download from Www.Somanuals.com. All3M7anuals Search And Download.
NAME PLATE INFORMATION
• When ordering parts or requesting information or assistance, always include the information listed
below.
• The Model Number and Serial Number for the Spreader are shown on the Name Plate.
• The space below is provided as a convenient place to record these numbers; just fill in the blanks.
Model No. ___________________________________________________________
Serial No. ___________________________________________________________
Date Purchased______________________________________________________
Purchased From _____________________________________________________
Phone No. For Service _______________________________________________
Postage
Required
Meyer Products
18513 Euclid Avenue
Cleveland, Ohio 44112-1084
Download from Www.Soman3ua8ls.com. All Manuals Search And Download.
|