ESPAÑOL: PÁGINA 17
FRANÇAISE : PAGE 33
Instruction
manual
Tile Saw
MODEL 1500
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Copyright © 2004 Porter-Cable Corporation
Part No. 895736 - 04-28-04
Download from Www.Somanuals.com. All Manuals Search And Download.
lug, and the like, extending from the adapter must be connected to a
permanent ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by
the Canadian Electric Code.
3. Grounded, cord-connected tools intended for use on a supply circuit
having a nominal rating between 150 - 250 volts, inclusive:
If the tool is intended for use on a circuit that has an outlet that looks
like the one illustrated in Fig. C, the tool will have a grounding plug that
looks like the plug illustrated in Fig. C. Make sure the tool is connected
to an outlet having the same configuration as the plug. No adapter is
available or should be used with this tool. If the tool must be re-
connected for use on a different type of electric circuit, the re-
connection should be made by qualified service personnel; and after
re-connection, the tool should comply with all local codes and
ordinances.
IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN
QUESTION IS PROPERLY GROUNDED. IF YOU ARE NOT SURE
HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.
NEVER REMOVE GROUNDING PRONG FROM POWER PLUG.
EXTENSION CORDS
Use proper extension cords. Make sure your extension
cord is in good condition and is a 3-wire extension cord which has a 3-
prong grounding type plug and matching receptacle which will accept
the tool’s plug. When using an extension cord, be sure to use one
heavy enough to carry the current of the tool. An undersized cord will
cause a drop in line voltage, resulting in loss of power and overheating.
Fig. D, shows the correct gauge to use depending on the cord length.
If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.
Length of Cord in Feet
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft. 150 Ft. 200 Ft.
250 Ft. 300 Ft.
500 Ft. 600 Ft.
400 Ft. 500 Ft.
800 Ft. 1000 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
Fig. D
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This information re-
lates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize
this information, we use the symbols below. Please read the manual and pay attention to these
sections.
indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
indicates a potentially hazardous situation which, if not avoided,may result in
minor or moderate injury.
used without the safety alert symbol indicates potentially hazardous situation
which, if not avoided, may result in property damage.
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known (to the State of California) to
cause cancer, birth defects or other reproductive harm. Some example of these chemicals are:
●
lead from lead-based paints
●
crystalline silica from bricks and cement and other masonry products
●
arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, always wear MSHA/NIOSH approved, properly fitting face mask or
respirator when using such tools.
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS.
1. For your own safety, read the instruction manual before operating
the tool. Learn the tool’s application and limitations as well as the specific
hazards peculiar to it.
2. Keep guards in place and in working order.
3. Always wear eye protection. Wear safety glasses. Everyday
eyeglasses only have impact resistant lenses; they are not safety
glasses. Also use face or dust mask if cutting operation is dusty. These
safety glasses must conform to ANSI Z87.1 requirements. NOTE:
Approved glasses have Z87 printed or stamped on them.
4. Remove adjusting keys and wrenches. Form habit of checking to see
that keys and adjusting wrenches are removed from tool before turning it
“on”.
5. Keep work area clean. Cluttered areas and benches invite accidents.
6. Don’t use in dangerous environment. Don’t use power tools in damp
or wet locations, or expose them to rain. Keep work area well-lighted.
7. Keep children and visitors away. All children and visitors should be
kept a safe distance from work area.
8. Make workshop childproof – with padlocks, master switches, or by
removing starter keys.
9. Don’t force tool. It will do the job better and be safer at the rate for
which it was designed.
10. Use the right tool. Don’t force tool or attachment to do a job for which
it was not designed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Wear proper apparel. No loose clothing, gloves, neckties, rings,
bracelets, or other jewelry to get caught in moving parts. Nonslip footwear
is recommended. Wear protective hair covering to contain long hair.
12. Secure work. Use clamps or a vise to hold work when practical. It’s
safer than using your hand and frees both hands to operate tool.
13. Don’t overreach. Keep proper footing and balance at all times.
14. Maintain tools in top condition. Keep tools sharp and clean for best
and safest performance. Follow instructions for lubricating and changing
accessories.
15. Disconnect tools before servicing and when changing accessories
such as blades, bits, cutters, etc.
16. Use recommended accessories. The use of accessories and
attachments not recommended by Delta may cause hazards or risk of injury
to persons.
17. Reduce the risk of unintentional starting. Make sure switch is in “OFF”
position before plugging in power cord. In the event of a power failure,
move switch to the “OFF” position.
18. Never stand on tool. Serious injury could occur if the tool is tipped or if
the cutting tool is accidentally contacted.
19. Check damaged parts. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to ensure that it will
operate properly and perform its intended function – check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
20. Direction of feed. Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
21. Never leave tool running unattended. Turn power off. Don’t leave
tool until it comes to a complete stop.
22. Stay alert, watch what you are doing, and use common sense
when operating a power tool. Do not use tool while tired or under
the influence of drugs, alcohol, or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
23. Make sure tool is disconnected from power supply while motor is
being mounted, connected or reconnected.
24. The dust generated by certain woods and wood products can be
injurious to your health. Always operate machinery in well ventilated areas
and provide for proper dust removal. Use wood dust collection systems
whenever possible.
25. Wear ear protection to safeguard against possible hearing loss.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SPECIFIC SAFETY RULES
1. Disconnect saw before servicing, when changing cutting wheels,
and cleaning.
2. Use splash hood for every operation for which it can be used.
3. To avoid the possibility of the appliance plug or receptacle getting
wet, position tile saw to one side of a wall mounted receptacle to prevent
water from dripping onto the receptacle or plug. The user should arrange a
“drip loop” in the cord connecting the saw to a receptacle. The “drip loop”
is that part of the cord below the level of the receptacle, or the connector if
an extension cord is used, to prevent water traveling along the cord and
coming in contact with the receptacle.
4. If the plug or receptacle does get wet, DON’T unplug the cord.
Disconnect the fuse or circuit breaker that supplies power to the tool.
Then unplug and examine for presence of water in the receptacle.
5. When the tool is not in use, the switch should be locked in the
OFF position to prevent unauthorized use of the tool.
6. Make sure your fingers and hands are not in the cutting line of
the blade.
7. Use only continuous wet cut diamond blades rated at 6000
RPMs or greater. Use tool only with smooth edge cutting wheels free of
openings and grooves.
8. Check water level and operation of pump before each use.
9. Replace damaged cutting wheel before operating tile saw.
10. Do not fill water bath above water fill line.
11. Only plug water pump cord into motor receptacle.
12. Ground Fault Circuit Interrupter (GFCI) protection should be
provided on the circuit(s) or outlet(s) to be used for the tile saw.
Improper operation or maintenance of this product could result
in serious injury and property damage. Read and understand all warnings and
operating instructions before using this tool. When using power tools, basic
safety precautions should always be followed to reduce the risk of personal
injury. For additional information visit our website www.porter-cable.com.
Additional Information regarding the safe and proper operation of power tools
(i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner
Information is also available from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201, the American National Standards Institute ANSI
01.1Safety Requirements for Woodworking Machines, and the U.S. Department
of Labor regulations.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
There are certain applications for which this tool was
designed. Porter-Cable strongly recommends that this tool NOT be modified
and/or used for any application other than for which it was designed. If you
have any questions relative to its application DO NOT use the tool until you
have written Porter-Cable and we have advised you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305
SYMBOL
DEFINITION
........................ volts
V
A
........................ amperes
........................ hertz
........................ watts
........................ kilowatts
........................ microfarads
........................ liters
Hz
W
kW
µF
l
kg
........................ kilograms
N/cm2 ........................ newtons per square centimeter
Pa
h
min
s
........................ pascals
........................ hours
........................ minutes
........................ seconds
........................ alternating current
3
........................ three-phase alternating current
3N
........................ three-phase alternating current with neutral
........................ direct current
........................ no load speed
n0
........................ alternating or direct current
........................ Class II Construction
........................ splash-proof construction
........................ watertight construction
…/min ........................ revolutions or reciprocation per minute
SAVE THESE INSTRUCTIONS
REPLACEMENT PARTS
When servicing use only identical replacement parts.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown
on the specification plate on the tool. Several models, however, are designed
for A.C. current only. Refer to the specification plate on your tool for proper
voltage and current rating.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not operate your tool on a current on which the
voltage is not within correct limits. Do not operate tools rated A.C.
only on D.C. current. To do so may seriously damage the tool.
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable Model 1500 Tile Saw is designed to cut ceramic tile. The
Model 1500 is powered by a 7.4 amp motor. The tile saw has the capacity to
cut 14" in length, 10" x 10” tile cut diagonally, and 2" depth cut.
ASSEMBLY
UNPACKING
1. Carefully remove the machine from the carton. We recommend you
retain all packing materials until after you have inspected and
satisfactorily operated the machine.
Do not connect the machine to the power source until you
have read and understood this entire instruction manual.
2. Place the machine on a firm, level surface where there is plenty of room
for handling and properly supporting the workpiece.
3. Familiarize yourself with all features and controls as explained in this
manual.
4. Unassembled items are shown in Fig. 1, for identification and use in
assembling the saw.
C
D
Q
R
B
E
F
J
O
G
P
A
I
K
N
M
Fig. 1
A
Water tray (1)
G ¼ - 20 x 1/2" Flat head screws (5)
N Arbor wrench (1)
B
Cutting tray (1)
I
J
Inner and outer blade flange
Blade (1)
O Arbor nut (1)
C Saw arm (1)
P
Rip guide (1)
D Motor (1)
K Hex wrench (1)
Q Cable tie (3)
E
F
Water pump (1)
Water plug (1)
M Flange wrench (1)
R Hose adapter (1)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
1. Locate and identify all parts.
2. Insert the plug (F) Fig. 1, into the
water tray (A) Fig. 1. The plug
should be inserted into the top of
the water tray as shown in Fig. 2.
ATTACHING THE MOTOR
TO THE SAW ARM
1. Place the motor on a flat surface.
Fig. 2
2. Line up the 3 holes (A) Fig. 3, in
the motor, with the 3 holes (A)
Fig. 4 in the saw arm.
3. Thread each screw (G) Fig. 1,
through the holes in the saw arm
to the holes in the motor.
A
B
Make sure that the
motor grounding tab (B) Fig. 3, stays
in place when attaching the motor to
the saw arm, for this provides a
means of grounding the motor.
Fig. 3
4. Once the screws are threaded
into the saw arm and motor, Fig.
5, tighten securely.
A
Fig. 4
Fig. 5
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING SAW ARM TO
THE CUTTING TRAY
1. Insert the water pump hose into
the largest hole in the side of the
cutting tray (from the outside)
Fig. 6, pull the hose through the
hole.
2. Position the saw arm (C) Fig. 1,
onto the cutting tray as shown in
Fig. 7.
Fig. 6
3. Insert 2 screws (G) Fig. 1,
through the 2 holes on the inside
of the cutting tray Fig. 8, and
tighten securely.
4. Place the water pump (E) Fig. 1,
into the bottom of the water tray
Fig. 9.
5. Attach the water pump hose,
from the saw, to the water pump
with the hose adapter (R) Fig. 1,
as shown in Fig. 9.
Fig. 7
Fig. 8
Fig. 9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 10
Fig. 11A
6. Plug the water pump cord into
the motor plug receptacle (Fig.
10). NOTE: Place cord through
the cord slot (Fig.11A), in the
water tray.
Only plug water pump
cord into motor receptacle.
A
7. Loosen the water hose clamp (A)
Fig. 11B, and insert cable tie (Q)
Fig. 1, through the water hose
clamp. Secure water pump cord
and motor cord to saw arm with
cable tie as shown in Fig. 11C.
Tighten the water hose clamp (A)
Fig. 11B.
Fig. 11B
8. Secure water pump hose and
cord to the cutting tray frame with
cable tie (Q) Fig. 1, as shown in
Fig. 11D.
ATTACHING THE SAW BLADE
Fig. 11C
NOTE: Use only continuous wet
cut diamond blades rated at 6000
RPMs or greater.
1. Loosen knob (A) Fig. 12, and
open the blade cover.
A
Fig. 11D
Fig. 12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Place the inner flange (I) Fig. 1,
onto the motor arbor as shown in
Fig. 13
3. Place the blade (J) Fig. 1, onto
the motor arbor. NOTE: Make
sure the blade is placed on the
arbor with the arrow on the blade
facing counter-clockwise, as
shown in Fig. 14.
4. Place the outer flange (I) Fig. 1,
onto the motor as shown in Fig.
15.
Fig. 13
Fig. 14
Fig. 15
5. Tighten the arbor nut (O) Fig. 1,
onto the arbor Fig. 16 using the 2
wrenches provided (M,N) Fig. 1.
NOTE: Wrench (M) Fig. 1, is used
to hold the arbor in place while
wrench (N) Fig. 1, is used to
tighten the arbor nut onto the
arbor.
6. Close blade cover and tighten
blade cover knob (A) Fig. 12.
7. Attach the rip guide (P) Fig. 1 to
the cutting tray by loosening the
locking knob and placing the rip
guide onto the front of the
cutting tray and tighten the
locking knob Fig 17.
Fig. 17
Fig. 16
OPERATION
STARTING AND STOPPING MACHINE
Make sure switch is OFF and power circuit voltage is the
same as that shown on the specification plate.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect machine to power circuit.
NOTE: To avoid the possibility of the
appliance plug or receptacle getting
wet, position tile saw to one side of a
wall mounted receptacle to prevent
water from dripping onto the receptacle
or plug. The user should arrange a “drip
loop” Fig. 18, in the cord connecting the
saw to a receptacle. The “drip loop” is
that part of the cord below the level of
the receptacle, or the connector if an
extension cord is used, to prevent
water traveling along the cord and
coming in contact with the receptacle.
Fig. 18
A
1. To start the machine, slide the
switch button (A) Fig. 19, down
until the switch locks into the ON
position.
2. To stop the machine, press on the
upper end of the switch button (A)
Fig. 20.
Fig. 19
A
LOCKING SWITCH
N THE “OFF” POSITION
IMPORTANT: When the tool is not in use,
the switch should be locked in the OFF
position using a padlock (A) Fig. 21, to
prevent unauthorized use of the tool.
OPERATING TILE SAW
Fig. 20
Before operating the tool, make sure
the tile saw is assembled properly.
Fill water tray to fill line and be sure
pump is totally submerged. Check
water level and operation of pump
before each use.
To cut tile, place the tile on the cutting
tray and turn the machine on. Hold the
tile firmly against the cutting tray with
both hands.
A
Fig. 21
Make sure your fingers
and hands are not in the cutting line of
the blade (A) Fig. 22A.
A
Push the cutting tray forward towards
the blade, feed the tile slowly and
evenly into the cutting blade until the
tile has been cut through completely.
Pull the tray backwards until the cutting
tray is in the rear most position and
remove the cut tile.
Fig. 22A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
WATER PUMP
The flow rate dial (A) Fig. 22B, should
be set on the maximum setting.
A
RIP GUIDE
The rip guide (A) Fig. 22A is used to
make precision cuts. Loosen knob (B),
position the rip guide on the cutting
tray scale to the amount of tile to be
cut off and then tighten knob. Hold
the tile against the rip guide and the
cutting tray and proceed to cut the tile
as discussed in the section
“OPERATING TILE SAW.”
Fig. 22B
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air
A
passages with dry compressed air.
All plastic parts should be cleaned
with a soft damp cloth. NEVER use
solvents to clean plastic parts. They
could possibly dissolve or otherwise
damage the material.
Wear ANSI Z87.1
safety glasses while using
compressed air.
Fig. 23
FAILURE TO START
The cutting tray can be detached
for cleaning purposes by pulling the
locking pin (A) Fig. 23 out, so that
the tray can slide off the rail.
Change water in water tray daily.
Do not leave water in water tray
overnight.
Should your tool fail to start, check
to make sure the prongs on the
cord plug are making good contact
in the outlet. Also, check for blown
fuses or open circuit breakers in the
line.
Do not cut tile
without using the tile cutting tray.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord
plug are making good contact in the outlet. Also, check for blown fuses or
open circuit breakers in the line.
LUBRICATION
This tool has been lubricated with a sufficient amount of high-grade
lubricant for the life of the unit under normal operating conditions. No further
lubrication is necessary.
BRUSH INSPECTION AND LUBRICATION
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE SERVICE
CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
Authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected; worn parts replaced, when necessary, relubricated with fresh
lubricant, if required; reassembled with new brushes; and performance
tested.
Any loss of power before the above maintenance check may indicate the
need for immediate servicing of your tool. DO NOT CONTINUE TO
OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is
present, return your tool to the service station for immediate service.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due
to wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE SERVICE
CENTER. All repairs made by these agencies are fully guaranteed against
defective material and workmanship. We cannot guarantee repairs made or
attempted by anyone other than these agencies. Should you have any
questions about your tool, feel free to write us at any time. In any
communications, please give all information shown on the nameplate of
your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable •
Delta Supplier, Porter-Cable • Delta Factory Service Centers, and
Porter-Cable Authorized Service Stations. Please visit our Web Site
www.porter-cable.com for a catalog or for the name of your nearest
supplier.
Since accessories other than those offered by Porter-Cable
• Delta have not been tested with this product, use of such accessories
could be hazardous. For safest operation, only Porter-Cable • Delta
recommended accessories should be used with this product.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
ARIZONA
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
GEORGIA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
OREGON
MISSOURI
Portland 97230
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
ILLINOIS
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
PENNSYLVANIA
St. Louis 63119
Willow Grove 19090 (Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
San Diego 92111
7638 Clairemnot Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
NEW YORK
TEXAS
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
MARYLAND
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
COLORADO
Houston 77043
4321 Sam Houston Parkway, West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
OHIO
FLORIDA
WASHINGTON
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-
•
•
•
•
•
•
•
•
Cable
•
Delta, s’adresser à tout distributeur Porter-Cable
•
Delta, centre de service agréé ou centre de service d’usine Porter-Cable
•
Delta. Si
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable
•
Delta le
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, P.Q.
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Mtl), P.Q.
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,
WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
Printed in U.S.A. PC-0104-150
Download from Www.Somanuals.com. All Manuals Search And Download.
|