ESPAÑOL: PÁGINA 13
FRANÇAISE : PAGE 25
14" Abrasive
Cut-Off Machine
Instruction
Manual
MODEL 1400
IMPORTANT
Please make certain that the person who is to use
this equipment carefully reads and understands
these instructions before starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. _____________________________________
Type __________________________________________
Serial No.______________________________________
Part No. 909516 - 02-26-03
Copyright © 2003 PORTER-CABLE Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure switch is in “OFF” position before plugging in
power cord. In the event of a power failure, move switch
to the “OFF” position.
21. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Don’t leave tool until it comes to a
complete stop.
18. NEVER STAND ON TOOL. Serious injury could occur
if the tool is tipped or if the cutting tool is accidentally
contacted.
22. STAY ALERT, WATCH WHAT YOU ARE DOING, AND
USE COMMON SENSE WHEN OPERATING A POWER
TOOL. DO NOT USE TOOL WHILE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION. A moment of inattention while operating
power tools may result in serious personal injury.
23. MAKE SURE TOOL IS DISCONNECTED FROM
POWER SUPPLY while motor is being mounted,
connected or reconnected.
24. THE DUST GENERATED by certain woods and wood
products can be injurious to your health. Always operate
machinery in well ventilated areas and provide for proper
dust removal. Use wood dust collection systems whenever
possible.
19. CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to ensure that it will operate properly and
perform its intended function – check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged should be
properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the blade or cutter
only.
ADDITIONAL SAFETY RULES FOR ABRASIVE CUT-OFF MACHINES
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
20. AFTER TURNING MACHINE ON, lower wheel
lightly until it comes into contact with the workpiece and
then draw wheel firmly through the cut. DO NOT allow
the wheel to chatter and jump as this may cause the
wheel to wear out of round, resulting in poor cutting and
possible broken wheels.
21. ANY MATERIAL CAN BE CUT more satisfactorily
when placed in position for the wheel to cut with the
least arc of contact.
22. THE NUMBER OF CUTS per wheel, as well as the
quality of cut, may vary considerably with the cutting time.
Fast cuts cause the wheel to wear more rapidly but also
help to reduce discoloration and burr. This is especially
noticeable when cutting light gage tubing. When coming
through the bottom wall, with the longer arc of contact, do
not slow up but give a vigorous pull. This keeps the metal
from overheating and dragging off in a heavy burr.
1. Do not operate your abrasive cut-off machine until it
is completely assembled and installed according to the
instructions.
2. IF YOU ARE NOT thoroughly familiar with the
operation of abrasive cut-off machines, obtain advice
from your supervisor, instructor or other qualified
person.
3. WEAR SAFETY GOGGLES, face shield, respirator,
body apron, head covering, safety shoes, long tight-
fitting sleeves and gloves.
4. USE ONLY RECOMMENDED reinforced abrasive
wheels with blotters.
5. TIGHTEN ARBOR SCREW and all clamps before
operating.
6. MAKE SURE spindle lock is disengaged before
operating.
7. ALWAYS KEEP GUARDS in place and working
23. USE THE WHEEL GUARD AT ALL TIMES.
24. NEVER OPERATE the machine in an area with
flammable liquids or gases.
properly.
8. KEEP HANDS CLEAR of cut-off wheel.
9. SECURE WORKPIECE PROPERLY. Work should
be straight and firmly clamped to avoid possible
movement and pinching as the cut nears completion.
10. NEVER CUT ANYTHING FREEHAND.
11. NEVER REACH behind or beneath the cut-off
wheel.
12. MAKE SURE the wheel has come to a complete
stop before removing or securing workpiece or changing
workpiece angle.
13. MAKE SURE the inside surfaces of the wheel
flanges as well as the sides of the wheel are free from
any foreign matter.
25. TO AVOID ELECTRIC SHOCK, do not use under
damp conditions or expose to rain.
26. THIS TOOL is designed for ferrous metals only. DO
NOT attempt to cut wood, masonry, aluminum or
magnesium with this tool.
27. AFTER INSTALLING a new wheel, never start the
tool with a person in line with the wheel. ALWAYS run the
tool for approximately one minute before cutting. If the
wheel has an undetected crack or flaw, it could burst in
less than one minute.
28. SHUT OFF POWER BEFORE SERVICING OR
ADJUSTING TOOL.
29. SHOULD ANY PART of your machine be missing,
damaged or fail in any way, or any electrical component
fail to perform properly, shut-off switch and remove plug
from power supply outlet. Replace missing, damaged or
failed parts before resuming operation.
14. WHEN MOUNTING the wheel, care should be taken
to tighten the arbor screw only enough to hold the wheel
firmly and to prevent wheel slippage. Excessive
tightening may result in damaging the wheel and
springing the wheel flanges.
30. ADDITIONAL INFORMATION regarding the safe
and proper operation of this product is available from
the National Safety Council, 444 N. Michigan Avenue,
Chicago, lL 60611, in the Accident Prevention Manual
for Industrial Operation and also in the Safety Data
Sheets provided by the NSC. Please also refer to the
American National Standard Institute ANSI B11.10
Safety Requirements for the Construction, Care and Use
of Metal Sawing Machines and the U.S. Department of
Labor OSHA 1910 Regulations.
15. USE ONLY abrasive wheels rated at 3900 RPM or
higher.
16. ALWAYS CHECK THE WHEEL for cracks or other
damage before operation. Replace cracked or damaged
wheel immediately.
17. USE ONLY wheel flanges specified for your
machine.
18. MAKE SURE abrasive wheel is not contacting
workpiece before switch is turned on.
19. ALLOW THE MOTOR to come up to full speed
before starting cut.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-
prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the
same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
MOTOR SPECIFICATIONS
Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
1. All grounded, cord-connected machines:
2. Grounded, cord-connected machines intended for use
on a supply circuit having a nominal rating less than 150
volts:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect
this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal
screw.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-
grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.
IN ALL CASES, MAKE CERTAIN
THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE HAVE A
QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. A.
Repair or replace damaged or worn cord immediately.
GROUNDED OUTLET BOX
GROUNDED OUTLET BOX
GROUNDING
MEANS
CURRENT
CARRYING
PRONGS
ADAPTER
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. A
Fig. B
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct
gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
Total Length
of Cord in Feet
Gauge of
Extension Cord
Volts
0-6
0-6
0-6
0-6
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
16 AWG
14 AWG
6-10
6-10
6-10
6-10
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
120
120
120
120
up to 25
25-50
50-100
100-150
16 AWG
16 AWG
14 AWG
12 AWG
12-16
12-16
12-16
120
120
120
up to 25
25-50
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
Fig. D
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable Model 1400 is a 14" Abrasive Cut-Off Machine designed to cut ferrous metals. Cutting capacities (at 90°)
are: 5-1/4" Dia. round stock, 4-1/4" x 4-1/4" square stock, and 2-3/4" x 7-3/16" rectangular stock. It is equipped with an
adjustable fence that can be set for angle cuts between 45° and 90°.
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT
PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE
ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR
ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE
MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION
MANUAL.
1. We recommend you retain all packing materials until after you have inspected and satisfactorily operated the
machine.
2. Place the machine on a sturdy work table.
3. Familiarize yourself with all features and controls as explained in this manual.
4. The machine is shipped with the cutting head (A) Fig. 4, held in the down position by the hold-down chain (B). Press
down on the tool handle to lower the cutting head. Unhook the hold-down chain from the side of the handle.
5. Slowly release pressure on tool handle allowing the cutting head to move to the up position as shown in
Fig. 5.
A
B
Fig. 4
Fig. 5
OPERATING CONTROLS AND ADJUSTMENTS
TO START AND STOP
MACHINE
Make sure power circuit voltage is
the same as shown on the specification plate of
the machine and that switch is OFF before
B
connecting to power circuit.
1. Squeeze trigger switch (A) Fig. 6, to start motor.
Release trigger switch to stop motor.
A
2. A lock button (B) Fig. 6, is provided to lock the
switch in the ON position. TO LOCK the switch ON,
squeeze the trigger as far as it will go, push in the lock
button and release trigger. TO UNLOCK the lock button,
squeeze trigger allowing lock button to spring out, and
release trigger.
Fig. 6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
F
B
C
A
C
D
E
Fig. 7
Fig. 8
SWITCH LOCKOUT
IMPORTANT: When the tool is not in use, the switch
should be locked in the “OFF” position to prevent
unauthorized use, using a padlock (C) Fig. 7 with a 3/16"
diameter shackle.
F
C
B
A
D
VISE
Clamping the workpiece can be accomplished quickly
and easily, as follows:
E
1. Depress lever (A) Fig. 8, to lift half-nut (B) off screw
(C).
Fig. 9
2. Pull out screw handle (D) Fig. 8, far enough to allow
workpiece (E) to be placed in vise opening against rear
vise clamp, as shown. NOTE: It is not necessary to
thread the screw (C) when the half-nut (B) is in the up
position. The screw handle (D) can be pulled out or
pushed in.
F
H
G
3. Push in on screw handle (D) Fig. 9, until front vise
clamp (F) contacts workpiece (E).
4. Rotate lever (A) Fig. 9, to engage half-nut (B) with
screw (C) and tighten screw handle (D) to securely clamp
workpiece in vise.
Fig. 10
ANGLE CUTTING
1. Loosen two screws (G) Fig.10, and rotate rear vise
clamp (H) to the desired angle. Then tighten the two
screws (G). The front vise clamp (F) pivots on its post
and will automatically align itself with the workpiece.
2. Fig. 11 illustrates a workpiece clamped in the vise
for a typical angle cutting operation.
Fig. 11
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING DOWNWARD
TRAVEL OF ABRASIVE
WHEEL
A
B
A stop screw (A) Fig. 12, is provided to limit the
downward travel of the abrasive wheel. This adjustment
is made by loosening lock nut (B) and turning stop screw
(A) in or out as desired. Then tighten lock nut (B).
Fig. 12
Fig. 13 illustrates edge of the arm casting (C) contacting
stop screw (A) limiting the downward travel of the
abrasive wheel. NOTE: As the abrasive wheel becomes
smaller in diameter, because of wear, the downward
travel of the wheel can be increased. When the blade is
changed, the stop screw (A) Fig. 12 will need to be re-
adusted to limit the downward travel of the wheel.
C
A
Fig. 13
WRENCH STORAGE
A slot (A) Fig.14, is provided on the back of the machine
base for convenient storage of the adjusting wrench (B),
which is supplied with your machine. Fig. 14 illustrates
the wrench (B) stored in position in the slot.
A
B
Fig. 14
CARRYING HANDLE
When transporting the machine, the cutting head should
always be locked in the down position by means of the
hold down chain (A) Fig. 15. A carrying handle (B) is
provided for ease of transportation.
B
A
Fig. 15
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
MAKING THE CUT
After clamping the workpiece securely in the vise, turn
the machine on and allow the motor to come up to full
speed. Lower the wheel (A) lightly until it comes into
contact with the workpiece (B), as shown in Fig. 17.
Do not allow the wheel to chatter and
jump as this may cause the wheel to wear out of round,
resulting in poor quality cutting and possible broken
wheels.
A
B
Fig. 17
Continue to push firmly down on the handle while the
cut is being made, as shown in Fig. 18.
Fig. 18
When coming through the bottom of the cut, as shown
in Fig. 19, do not slow up. This keeps the metal from
overheating and dragging off in a heavy burr.
Fig. 19
Fig. 20 illustrates the cut-off piece after the cut is
completed. NOTE: The number of cuts per wheel, as
well as the quality of cut, may vary considerably with the
cutting time. Fast cuts cause the wheel to wear more
rapidly but also help to reduce discoloration and burr.
Fig. 20
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHANGING THE WHEEL
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Rotate the front wheel guard (A) Fig. 21, to the up
position, as shown.
A
Fig. 21
2. Press in on arbor lock (B) Fig. 22, and at the same
time rotate wheel (F) by hand until the arbor lock
engages.
B
Fig. 22
3. Using the wrench provided, loosen arbor screw (C)
Fig. 23, by turning it counterclockwise and remove arbor
screw (C), washer (D), outside wheel flange (E) and
wheel (F). DO NOT REMOVE INSIDE WHEEL FLANGE.
4. Make sure the inside surfaces of both the inside and
outside wheel flanges are clean and free from any
foreign substance.
E
F
D
5. Install new wheel, outside wheel flange (E) Fig. 23,
washer (D), and arbor screw (C). Turn arbor screw (C)
clockwise to tighten.
C
USE ONLY RECOMMENDED REINFORCED
ABRASIVE WHEELS WITH BLOTTERS AND TIGHTEN THE
ARBOR SCREW (C) ONLY ENOUGH TO HOLD THE
WHEEL FIRMLY AND PREVENT WHEEL SLIPPAGE.
EXCESSIVE TIGHTENING MAY RESULT IN DAMAGE TO
THE WHEEL AND SPRINGING THE WHEEL FLANGES.
Fig. 23
6. Rotate front wheel guard to the down position and
make sure spindle lock is disengaged before turning the
machine on.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH INSPECTION
AND REPLACEMENT
DISCONNECT MACHINE FROM POWER
SOURCE.
A
Brush life varies. It depends on the load on the motor.
Check the brushes after the first 50 hours of use for a new
machine or after a new set of brushes have been installed.
After the first check, examine the brushes after about 10
hours of use until such time that replacement is necessary.
Fig. 24
The brush holders (A) Fig. 24, are located on the motor
housing opposite each other. Fig. 25 illustrates one of the
brushes removed for inspection. When the carbon on either
brush is worn to 3/16" in length or if either spring or shunt
wire is burned or damaged in any way, replace both
brushes. If the brushes are found servicable after removing,
reinstall them in the same position as removed.
Fig. 25
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth. NEVER use
solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.
WEAR SAFETY GLASSES WHILE USING COMPRESSED AIR.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact with the outlet.
Also, check for blown fuses or open circuit breakers in the line.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations,
including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER-CABLE
SERVICE STATION or a PORTER-CABLE·DELTA FACTORY SERVICE CENTER. All repairs made by these agencies are
fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by
anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all
information shown on the nameplate of your tool (model number, type, serial number, etc.).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
A complete line of accessories is available from your Porter-Cable·Delta Supplier, Porter-Cable·Delta Factory Service
Centers, and Porter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog
or for the name of your nearest supplier.
Since accessories other than those offered by Porter-Cable·Delta have not been tested
with this product, use of such accessories could be hazardous. For safest operation,
only Porter-Cable·Delta recommended accessories should be used with this product.
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from
state to state.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Delta Machinery are Available at These Locations
Parts and Repair Service for Porter-Cable
•
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta)
ARIZONA
ILLINOIS
MINNESOTA
Cleveland 44125
Minneapolis 55429
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
8001 Sweet Valley Drive
Unit #19
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
Phone: (216) 447-9030
Fax: (216) 447-3097
Phone: (602) 437-1200
Fax: (602) 437-2200
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MISSOURI
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
MARYLAND
St. Louis 63119
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
COLORADO
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
Houston 77055
Phone: (954) 321-6635
Fax: (954) 321-6638
West 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
MICHIGAN
OHIO
WASHINGTON
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Fax: (248) 597-5004
Phone: (404) 608-0006
Fax: (404) 608-1123
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service Center, or
Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to the nearest Porter-
Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades. Llame al 800-487-8665 ó
al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-Cable Delta deben obtenerse
poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable
Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable Delta más
cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au 800-487-8665 ou au 731-541-6042 pour obtenir de
l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-Cable Delta, s’adresser à tout distributeur Porter-Cable
Delta, centre de service agréé ou centre de service d’usine Porter-Cable Delta. Si vous n’avez accès à aucun de ces centres, appeler le 888-848-
5175 et on vous dirigera vers le centre de service d’usine Porter-Cable Delta le plus proche.
•
•
•
•
•
•
•
•
•
•
•
•
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
QUÉBEC
MANITOBA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1515 ave.
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste,
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
1447, Begin
505 Southgate Drive
Guelph, Ontario
N1H 6M7
St-Laurent, (Montréal),
Québec
V5A 4T8
H4R 1V8
Phone: (519) 836-2840
Fax: (519) 767-4131
Phone: (604) 420-0102
Phone: (514) 336-8772
Fax: (604) 420-3522
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE·
DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®, BAMMER®,
B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™,
Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®,
MICRO-SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®, Q-3®&(design), QUICKSAND®&(design), QUICKSET™,
QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®,
Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®, The American Woodshop®&(design), The Lumber
Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®,
TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®,
Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las
Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden estar
registradas en otros países.
Printed in U.S.A.
PC-0203-150
Download from Www.Somanuals.com. All Manuals Search And Download.
|