SpectraLink 8002 Wireless Telephone
Administration Guide
Session Initiation Protocol (SIP)
April 2008 Edition
1725-36034-001
Version B
Download from Www.Somanuals.com. All Manuals Search And Download.
Essential Installation Pointers
You must update the software with the most recent code.
•
Additional information about updating handset code is in Chapter 3 Software License and
Protocol Management.
WMM QoS must be supported and enabled on the Wi-Fi access point(s).
•
When using the SpectraLink 8002 Wireless Telephones, WMM QoS is mandatory to ensure
voice packets are delivered in a timely fashion. The AP must have WMM enabled. If WMM is
not enabled or if the AP does not support it, the handset will stop and display an error (e.g.
No Net Found) after firmware update.
•
Be aware that not all APs enable WMM by default. In fact, many APs require updated
firmware to support WMM. Follow the AP’s manufacturer instructions to ensure WMM is
supported and enabled.
Data APs may not support VoWiFi.
•
The 8002 handset has been tested with many SMB access points. We have found that
VoWiFi performance varies between AP models and even firmware versions. An AP being
used for data does not guarantee satisfactory Voice over Wi-Fi performance.
•
We recommend that you update to the latest AP firmware version if possible. If you
experience unexpected behaviors, try a different AP type.
A TFTP server must be on the local network with the SIP configuration files present.
•
A TFTP server is a required component of the LAN. The SIP configuration files (and the
handset code) reside on the TFTP server and the handset retrieves the SIP files at every
power up. It is not recommended or supported to have the TFTP server or call-server across
a WAN.
•
•
The handset must be configured to point to a TFTP server for the SIP configuration files.
This is accomplished by setting the handset for DHCP or by using static IP addressing. See
Chapter 2 SpectraLink 8002 Wireless Telephone Configuration, section Network Config.
If the handset cannot find the files, it will stop and report an error.
A knowledge base to assist troubleshooting is available at:
PN: 1725-36034-001_B.doc
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
About this Guide
This document explains how to configure and maintain the
SpectraLink 8002 Wireless Telephones with Session Initiation Protocol
(SIP); a protocol for the control of voice over IP (VoIP) calls.
Polycom Model Numbers
This document covers the following registered model number:
SNP2400
Related Documents
SpectraLink 8002 Wireless Telephone and Accessories User Guide.
(1725-36027-001)
SpectraLink 8002 Wireless Telephone Quick Reference Guide
(1725-36026-001)
SpectraLink 8002 Wireless Telephone Deployment Guide
(1725-36166-001)
Available at
Open Application Interface (OAI) Specification
(72-0052-00)
Technical specifications available by request.
Please contact Customer Support.
PN: 1725-36034-001_B.doc
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Customer Support Hotline
Polycom wants you to have a successful installation. If you have
questions please contact our Customer Support Hotline at
(800) 775-5330. The hotline is open Monday through Friday,
6 a.m. to 6 p.m. Mountain time.
Icons and Conventions
This manual uses the following icons and conventions.
Caution! Follow these instructions carefully to avoid danger.
Note these instructions carefully.
This typeface indicates a key, label, or button on Polycom
hardware.
Label
6
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
PN: 1725-36034-001_B.doc
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Site Survey..........................................................................................73
8
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Syslog Mode.......................................................................................79
PN: 1725-36034-001_B.doc
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
SpectraLink Wireless Telephone
Overview
SpectraLink 8002 Wireless Telephones are mobile handsets for
workplace IP telephone systems. The handsets operate over an
802.11b wireless Ethernet LAN providing users a wireless voice over
IP (VoIP) extension. By seamlessly integrating into a SIP environment,
handset users are provided with high-quality mobile voice
communications throughout the workplace. The handset gives users
the freedom to roam throughout the workplace while providing all
the features and functionality of a SIP desk phone.
The handsets reside on the wireless LAN with other wireless devices
using direct sequence spread spectrum (DSSS) radio technology.
Access points that transmit these signals must use WMM for QoS. The
handset radio transmits and receives packets at up to 11 Mb/s.
In the SIP environment, the handsets support up to three proxy
servers. Each handset may have five line appearances and two calls
per line. If required, each handset may have multiple sets of
credentials to identify itself by current user.
The latest software versions are required to support the features
described in this document.
WMM-Compatible Access Points
SpectraLink 8002 Wireless Telephones support basic WMM™ as part
of the 802.11e protocol. The handset requires an AP that supports
WMM
The WMM specification for the SpectraLink 8002 Wireless Telephone
does not accommodate admission control. The AP may not use the
mechanism of admission control in the wireless environment where
SpectraLink 8002 Wireless Telephones are operating.
PN: 1725-36034-001_B.doc
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
WMM must be enabled when configuring access points for the
SpectraLink 8002 Wireless Telephones. The handset will not work
properly if WMM is not enabled.
Refer to the access point manufacturer’s directions for instructions
on enabling WMM.
support WMM.
Security Options
The SpectraLink 8002 Wireless Telephone supports Wired Equivalent
Privacy (WEP) as defined by the 802.11 specification. Polycom offers
the product with both 40-bit and 128-bit encryption.
SpectraLink 8002 Wireless Telephones also support the 802.11i
protocol including Wi-Fi Protected Access (WPA™ and WPA2™)—
PSK.
12
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Overview
Quick Start Guide
1. A wireless LAN must be properly configured and operational
through the use of 802.11 wireless APs. Ensure WMM is enabled
on the APs.
2. Configure a TFTP server on the LAN. The TFTP server is used to
load the handset software and SIP configuration files into the
handsets. See Chapter 2 SpectraLink 8002 Wireless Telephone
Configuration for DHCP information.
3. The supported SIP system components must be connected to your
network and completely operational.
fi/spectralink_8002_wireless.html to download the latest handset
software and example SIP configuration files.
5. Ensure the handset software is properly loaded on the TFTP
server that has been designated for the handset code. See Chapter
3 Software License and Protocol Management, section Configuration
Process.
6. Create/modify configuration files on the SIP TFTP server to
define parameters for the SIP application. See Chapter 4
Programming the SIP Handset Features, section SIP TFTP Server
Configuration Files. The TFTP server may be the same one
referenced in step 2 above.
7. Configure your handset per Chapter 2 SpectraLink 8002 Wireless
Telephone Configuration. Ensure these configuration options are
set:
— Regulatory Domain
— SIP Registration, Reg 1 and Login
— IP Addresses: DHCP or static for each listed component,
including SIP TFTP server and TFTP server.
— Security
— Preferred Channels
PN: 1725-36034-001_B.doc
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
System Diagram
The following diagram shows the SpectraLink components residing
on a network with APs and a wireless LAN Ethernet Switch.
SIP config files
Handset code
Access point
TFTP server
Ethernet switch
Access point
SIP Server(s)
SIP proxy or SIP B2BUA
internet
Optional SIP
Phones
Ethernet cable
Supplied by
Polycom
14
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Overview
System Components
SpectraLink 8002 Wireless Telephone
The SpectraLink 8002 Wireless Telephone is a lightweight, durable
handset specifically designed for mobile workplace use within a
facility using SIP and an 802.11 wireless LAN. The handsets are to be
used on-premises; they are not cellular or satellite phones.
SpectraLink 8002 Wireless Telephones use direct-sequence spread
spectrum radio technology (DSSS) to transmit audio packets over
wireless LAN APs that support WMM.
Access points
Supplied by third-party vendors, APs provide the connection
between the wired Ethernet LAN and the wireless (802.11) LAN.
Access points must be positioned in all areas where handsets will be
used. The number and placement of APs will affect the coverage area
and capacity of the wireless system.
Access points must support WMM, WMM must be enabled and
admission control must be disabled.
Ethernet switch
Interconnects multiple network devices, including the proxy server(s),
wired IP phones and the APs. Ethernet switches provide the highest
performance networks, which can handle combined voice and data
traffic, and are required when using the SpectraLink 8002 Wireless
Telephones.
Although a single Ethernet switch network is recommended, the
handsets can operate in larger, more complex networks, including
networks with multiple Ethernet switches, routers, VLANs and/or
multiple subnets. However, in such networks, it is possible that voice
quality may suffer. Any network that consists of more than a single
Ethernet switch should be thoroughly tested to ensure any quality
issues are detected.
Note that the SpectraLink 8002 Wireless Telephones cannot “roam”
from one subnet to another. If routers and multiple subnets are in use,
PN: 1725-36034-001_B.doc
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
the handsets must only use APs attached to a single subnet, or be
powered off and back on to switch to a different subnet.
SIP server
The SIP server is a component from a third-party vendor that
provides access to telephony services. The handsets can recognize up
to three distinct SIP servers in a single system.
The SIP proxy server connects to another device such as a PBX or
gateway and from there, other wired phones and the PSTN.
The SpectraLink 8002 Wireless Telephone has been tested and
certified with Digium® Asterisk® Business Edition server.
SIP phone
The optional wired-LAN desksets such as those provided by
Polycom.
TFTP server
A TFTP server is required in the system to distribute software to the
handsets. May be on a different subnet than the gateway and/or APs.
SIP TFTP server
A SIP TFTP server is required in the system to deliver SIP
configuration parameters to the SIP handset whenever a SIP handset
is powered-up. The location of the SIP TFTP server is separately
specified in SIP handset administration parameters (See Chapter 2
SpectraLink 8002 Wireless Telephone Configuration, section The Admin
Menu.) Normally, the SIP TFTP server is the same as the network
TFTP server, see above.
16
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Overview
Handset Specifications
SpectraLink 8002 Wireless Telephone
2.4000 – 2.4835 GHz
Radio frequency:
Transmission type:
Transmit data rate:
Radio QoS:
Direct-sequence spread spectrum (DSSS)
Up to 11 Mb/s
WMM
Wireless security:
Wired Equivalent Privacy (WEP), 40-bit and 128-bit, WPA-PSK,
WPA2-PSK
FCC certification:
Management:
Voice encoding:
VoIP Protocols:
Transmit power:
Display:
Part 15.247
DHCP, TFTP
G.711 (A- and mu-law),
SIP
100 mW peak, < 10 mW average
Pixel-based (up to 4-line x 18-character) alphanumeric, plus line and
status indicators.
Dimensions:
Weight:
5.5” x 2.0” x 0.9” (14.0 x 5.1 x 2.3 cm)
4.2 ounces (119.0 g)
Battery capacity:
Up to 3 hours talk time, up to 50 hours standby
PN: 1725-36034-001_B.doc
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Startup Sequence
The SpectraLink 8002 Wireless Telephone goes through an
initialization sequence at startup. The line icons 1-9 display and count
down as the handset steps through this sequence. This is usually very
rapid. If there is difficulty at any step that prevents initialization from
continuing, an error message will display and the related icon(s) will
stay on. Please see the error table at the back of this document for
instructions on how to handle error messages that occur during
initialization.
Icon
The icon(s) shown in bold turns off when:
123456789 The handset has located and authenticated and associated with at least one AP, and is
proceeding to bring up higher-layer networking functions.
12345678
The handset is either configured for Static IP, or if configured for DHCP, the DHCP
discovery process has started.
1234567
If DHCP is configured, a DHCP response was received which contains a good DNS
server configuration.
123456
Indicates Static IP configuration.
12345
All networking functions are complete (notably, DHCP) and the handset is establishing
its connection to the LAN.
1234
123
12
The LAN connection is complete.
The handset has located a generic SIP config file.
The handset has located a handset-specific SIP config file.
Handset is attempting to register each of the specified line contacts.
(no icons)
Registering
(no icons)
Handset has registered with at least one contact on one proxy server. Initialization is
complete. The handset is in standby mode ready to receive and place calls. The line one
contact is displayed.
EXT.
XXXXX
During the last three steps of this process, the handset contacts the SIP
TFTP server and downloads general information about the proxy
server(s), downloads specific information pertaining to the handset,
registers with the proxy server(s), and verifies handset credentials.
Once this process is complete, the handset is ready to use.
18
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Overview
If the username and password have not been defined in the Admin
menu, you will be prompted to enter both of these items before the
extension number can display. The user name must correspond to a
handset-specific configuration file. If the file is not found, an error
message will appear and the handset will restart. See Chapter 4
Programming the SIP Handset Features.
PN: 1725-36034-001_B.doc
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
SpectraLink 8002 Wireless
Telephone Configuration
Each SpectraLink 8002 handset may be configured for site-specific
requirements by opening the Admin menu and selecting options or
entering specific information. Any settings entered in the Admin
menu must conform to system settings. Only the handset being
configured is affected by the Admin menu settings.
The Wireless Telephone user may select several usability options from
the Standby menu, described below in the User-defined Preferences
section. This information is also provided in the end-user manual.
The SpectraLink Configuration Cradle is an accessory device
designed to automate configuration of SpectraLink 8002 Wireless
Telephones. The Configuration Cradle is connected to a PC via a
serial cable. A downloadable Configuration Cradle program runs on
the PC and enables the system administrator to establish and store
configuration options for system, group and user categories. A
configuration plan may be set up in the program and downloaded
into a handset or a configured handset may be placed in the cradle
and its configuration may be uploaded and edited or saved.
Please see your service representative or contact Polycom Customer
Service for more information about this time-saving device.
PN: 1725-36034-001_B.doc
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
The Admin (Administration) Menu
The Admin menu contains configuration options that are stored
locally (on each handset). Each handset is independent, and if the
default settings are not desired, the Admin menu options must be set
in each handset requiring different settings.
Opening the Admin menu
1. With the handset powered off, press and hold the Power Off key.
While holding the Power Off key, press and release the Power On
key.
2. The Admin menu displays.
If an Admin password has been set, the display will require its entry
before opening the Admin menu. The default password is 123456. If
no password is set, the display will proceed directly into the Admin
menu.
Entering and editing Admin menu options
An asterisk (*) next to an option on the display indicates that it is
selected. Use the Up, Down, and Select side buttons and the softkeys to
navigate and select:
Display previous/next menu item.
Selects the menu item or option.
Selects the menu item or option.
Saves the entry.
Up/Down button:
Select button:
OK softkey:
Save softkey:
Bksp softkey:
Cncl softkey:
Up softkey:
Backspaces to allow editing of entry.
Cancels edit and returns to previous menu level.
Returns to previous menu level.
Exits the menu (at the top level).
Exits to standby mode (from any level)
Exit softkey:
End Call key:
Alphanumeric string entry
1. Press the first digit/letter. The digit displays. Press the key again
to scroll through the letters associated with that key.
22
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
Example: if the 2 key is repeatedly pressed, the handset will
display 2, A, B, and C, then a, b, and c.
The following table shows which key will allow you to enter non-
numeric characters or other characters not represented on the keypad.
To Enter
Press
. - _ ! # $ % & ‘ ( ) * + , : ; / \ = @ ~
1
Space
Q,q
0
7
9
Z,z
2. When the correct entry displays, press the right arrow key (#) to
move on to the next character. Repeat for each digit/letter of the
entry. To erase, press the left arrow key (*) or Bksp softkey to erase
the previous character.
3. Press the Save softkey to save the entry.
Press the Up softkey to abort and return to the menu without
saving any changes.
The following table lists the Admin menu items. The default settings
are shown in the table below with an * prior to the option. Detailed
descriptions of each item appear below the table.
PN: 1725-36034-001_B.doc
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Admin menu
Admin Menu Items
2nd Level
3rd Level
4th Level
5th Level
Phone Config
Network Config
Open System
Shared Key
WEP Off
WEP On
Default
Key
Key
Length
Key 1-4
24
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
Admin Menu Items
2nd Level
3rd Level
4th Level
5th Level
Diagnostics
Restore Defaults
* default setting
†50 mW and 30 mW only appear if Regulatory Domain is set to None or 01.
‡ Available channel selections depend on domain setting.
PN: 1725-36034-001_B.doc
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Phone Config
License Option
The License Option indicates the VoIP protocol that your site is
licensed to download and run. The SIP protocol used for the
SpectraLink 8002 Wireless Telephones requires license option
selection 22.Any other protocol will cause the handset to malfunction.
SIP Registration
Individual handsets can be configured to correspond with a handset-
specific configuration file in the TFTP server. The handset is then
automatically identified at startup.
If the username and password information is not configured in the
Admin menu, then this information will be requested at startup. The
username and password entered must agree with a corresponding
handset-specific configuration file. See Chapter 4 Programming the SIP
Handset, section SIP TFTP Server Configuration Files.
Reg 1 and Login allows you to specify a username and password for
automatically acquiring SIP configuration information. If no
username is specified, the SIP handset will request username and
password at startup and any additional registrations specified here
are ignored.
The username should correspond to the primary (line 1) dial number
assigned to the user. The username and password should also
correspond to the authentication credentials as created by your
system administrator for your primary line registration. Usernames or
passwords can be erased by selecting the item, then pressing Bksp
softkey and then Save softkey.
Reg 2, Reg 3, and Reg 4 allow you to specify additional authentication
usernames and passwords that may be required by your handset for
any additional line appearances (registrations) that may appear in the
specific user’s configuration file. This information will be ignored if a
Reg 1 and Login username is not provided.
OAI On/Off
SpectraLink’s Open Application Interface (OAI) enables third-party
computer applications to display alphanumeric messages on the
26
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
handset display and take input from the handset keypad. Refer to the
OAI Specification documentation for information about administering
the OAI Gateway and the services it can provide.
If OAI is enabled, and an IP address (called the OAI Server IP) is
available to the handset (either via DHCP or Static IP configuration),
the handset will communicate with the OAI Gateway at power-on,
and periodically while it is powered-on. If you don’t have a
SpectraLink 8000 OAI Gateway installed at your site, you should
disable the OAI feature to preserve network bandwidth and battery
life.
To conserve handset battery life, do not enable OAI unless an OAI
gateway is present and an application is available.
Admin Password
The Admin Password controls access to the administration functions
in the Admin menu. The password must be set in each handset for
which controlled access is desired. Handsets are shipped without any
Admin menu password. Data entry for the password uses the
alphanumeric string entry technique. A password may be up to 32
characters. Type the password and press the Save softkey. A
confirmation prompt will appear. Type the password again and press
the Save softkey. If the passwords match, the Admin password has
been set.
If you Save with no entry, the password is erased and the display will
not require it before displaying the Admin menu.
Network Config
IP Address
There are two modes in which the handset can operate: DHCP-
enabled or Static IP. Select the mode for operation from the IP
Address menu:
* Use DHCP Will use Dynamic Host Configuration Protocol to assign
an IP Address each time the handset is turned on. If DHCP is enabled,
the handset also receives all other IP Address configurations from the
DHCP server.
PN: 1725-36034-001_B.doc
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Dynamic Host Configuration Protocol (DHCP) is a standardized
protocol that enables clients to be dynamically assigned with various
configuration parameters, such as an IP address, subnet mask,
default gateway, and other critical network configuration information.
DHCP servers centrally manage such configuration data, and are
configured by network administrators with settings that are
appropriate for a given network environment. The handset will use
the following DHCP options if DHCP use is enabled.
Option
Meaning
1
Subnet mask
3
Default gateway
6
DNS server
7
Syslog server
15
66
152
siaddr
Domain name
TFTP server
SpectraLink 8000 OAI Gateway
Boot server or next server
Static IP Allows you to manually set a fixed IP Address. If selected, the
handset will prompt for the IP addresses for each configurable
network component. When entering addresses, enter the digits only
including leading zeroes, e.g. 192.168.001.002. No periods are
required.
Regardless of the mode in which the handset is operating, the
following components are required and must be configured as part of
the SIP system:
Phone IP The IP address of the handset. This is automatically
assigned if DHCP is used. If using Static IP configuration, you
must obtain a unique IP Address for each handset from your
network administrator.
TFTP Server IP The IP address of a TFTP server on your network,
which holds software images for updating the handsets and
contains the handset files. If this feature is configured (not set to
0.0.0.0 or 255.255.255.255) with either Static IP configuration or
using DHCP option 66 (TFTP server), or the boot server/next
server (siaddr) field, the handset will check for newer software
each time it is powered on or comes back into range of your
network. This check takes only a second and ensures that all
handsets in your network are kept up-to-date with the same
version of software.
28
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
The TFTP server and the SIP TFTP server may be the same device
with the same IP address or may be different devices with
different IP addresses.
Default Gateway and Subnet Mask Used to identify subnets, when
using a complex network, which includes routers. Both of these
must be configured either with an IP address under Static IP (not
set to 000.000.000.000 or 255.255.255.255) or with DHCP for the
handset to contact any network components on a different subnet.
If configured on the DHCP server, use option 3 for the Default
Gateway and option 1 for the Subnet Mask. Contact the network
administrator for the proper settings for the network.
Note that the wireless telephones cannot “roam” across subnets,
since they cannot change IP addresses while operational. Ensure
that all APs are attached to the same subnet for proper operation.
The handset can change subnets if DHCP is enabled and the
handset is powered-off then back on when within range of only APs
on the new subnet.
Syslog Server IP The IP address of the syslog server. See Chapter 5
Diagnostic Tools for more information.
SIP TFTP Server IP The IP address of a TFTP server on your network,
which holds SIP configuration files. In static mode, this parameter
must be configured with an IP address. In DHCP mode, the SIP
TFTP server may be specified by defining the address on the DNS
server for the name “siptftp” If this is not defined, the address
specified in option 66 will be used.
The TFTP server and the SIP TFTP server may be the same device
with the same IP address or may be different devices with
different IP addresses.
OAI Server IP The IP address of the SpectraLink OAI Gateway. If
using Static IP configuration, this is simply the IP address of the
SpectraLink OAI Gateway. If DHCP is being used, the handset
will try the DHCP option 152.
PN: 1725-36034-001_B.doc
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Domain Name System (DNS), an industry-standard protocol, locates
computers on an IP-based network. IP networks rely on number-
based addresses to move information on the network. However, it is
easier to remember friendly names than number-based addresses,
so it is necessary to translate user-friendly names into addresses
that the network can recognize. The handset will use DNS to
automatically translate names into IP addresses for the TFTP server.
In DHCP mode, the SIP handset will use DNS to look up an address
for the logical name “siptftp” to locate the SIP TFTP file server. If this
logical name is undefined, then the address specified by option 66 is
used for the SIP TFTP server.
ESSID
Select the option that will enable the handset to acquire APs with the
correct ESSID (Extended Service Set ID, aka SSID) each time it is
turned on.
Note about Automatic Learn options: Broadcast ESSID must be
enabled in the APs for ESSID learning to function when multiple
ESSIDs can be seen by the handset from one location. Overlapping
wireless systems complicate the use of ESSID learning as the handset
in an overlapping area could receive conflicting signals. If this is the
situation at your site, use Static Entry or Learn Once in an area
without overlapping ESSIDs.
* Learn Once Allows the handset to scan all ESSIDs for a DHCP
server. Once either is found, the handset retains the ESSID from
whichever AP it associates with at that point. When overlapping
wireless systems exist, the Learn Once feature allows the handset
to use only the ESSID established at first learn at all subsequent
power ons. This ESSID is retained by the handset until the ESSID
option is reselected in the Admin menu, thus erasing the stored
ESSID..
Learn Always Allows the handset to automatically learn the ESSID
at each power on or loss of contact with the wireless LAN (out of
range). This may be useful if the handset will be used at more than
one site.
Static Entry If the APs do not broadcast their ESSID, or if there are
overlapping wireless systems in use at the site, enter the ESSID
manually.
30
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
Security
*NONE disables any 802.11 encryption or security authentication
mechanisms.
For WEP, WPA-PSK and WPA2-PSK set each of the following
options to match exactly the settings in the APs.
The encryption key or encryption passphrase displays as it is
entered. For security reasons codes will not display again once
entered, even if the entry screen is revisited.
WEP (Wired Equivalent Privacy) is a wireless encryption protocol that
encrypts data frames on the wireless medium allowing for greater
security in the wireless network. If WEP is required at this site, you
must configure each handset to correspond with the encryption
protocol set up in the APs. Select the entries from the options below to
enable the handset to acquire the system.
Authentication Select either Open System or Shared Key.
WEP On/Off Select either WEP Off or WEP On.
Key Information
Default Key Enter the key number specified for use by the
handsets. This will be 1 through 4.
Key Length Select either 40-bit or 128-bit depending on the key
length specified for use at this location.
Key 1 through 4 Scroll to the key option that corresponds to the
Default Key that was entered above. Enter the encryption key as
a sequence of hexadecimal characters. (Use the 2 and 3 keys to
access hexadecimal digits A-F, use the Right Arrow key to
advance to the next digit, and the Left Arrow key to
backspace.) For 40-bit keys, enter 10 hex characters. For 128-bit
keys, enter 26 hex characters. The display will scroll as needed.
Rotation Secret This is used for proprietary WEP key rotation. Refer
to your custom document if this feature is supported in your
system.
WPA-PSK The security features of WPA (Wi-Fi Protected Access)
using PSK (pre-shared key) are available and may be used if
supported by the APs in the facility. Select either Passphrase and enter
a passphrase between eight and 63 characters in length or Pre-shared
Key and enter the 256-bit key code.
PN: 1725-36034-001_B.doc
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
WPA2-PSK The security features of WPA2 (Wi-Fi Protected Access)
using PSK are available and may be used if supported by the APs in
the facility. Select either Passphrase and enter a passphrase between
eight and 63 characters in length or Pre-shared Key and enter the 256-
bit key code.
Regulatory Domain
The Regulatory Domain will default to None on the handset display.
FCC requirements dictate that the menu for changing the domain be
available by password, which in this case is the LINE key. To change
the domain, press LINE and then enter the digits that represent the
site’s domain. Note that both digits must be entered.
01 North America
02 Europe (except Spain and France); Japan (channels 1-13)
04 Spain
05 France
06 Korea
As of this writing, Spain and France are adopting the general
European regulatory rules. Check with your wireless LAN
administrator or supplier regarding which domain to enter in these
countries.
Transmit Power
Available Transmit Power is regulated by domain. The Regulatory
Domain setting above affects the options available for this setting. The
default setting is Maximum which in North America is 100 mW. The
Maximum in other domains is 30 mW. Transmit Power may be set to
a lower number if necessary by selecting one of the other levels. If
changed from the default, ensure the Transmit Power setting is the
same on all handsets and all APs.
Power is limited to 30mW in regulatory domains other than North
America.
See Appendix A for the full list of certified countries and the
corresponding domain for each.
32
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
Preferred Channel
The Preferred Channel option lists the channels that are permitted
within the regulatory domain previously set. To speed up handoff,
the handset will look for APs on the preferred channel list first. If no
AP is found, the handset will then will look for APs on the non-
preferred channels. Selected channels are marked with an asterisk.
You may select more than one channel.
Diagnostics
Run Site Survey
The Site Survey mode is activated by selecting this option. The site
survey starts running immediately upon selecting this option. See
Chapter 5 Diagnostic Tools for more information about site survey.
Diagnostics Mode
See Chapter 5 Diagnostic Tools for a detailed explanation of the
Diagnostics Mode options.
Syslog Mode
See Chapter 5 Diagnostic Tools for a detailed explanation of the Syslog
Mode options.
Restore Defaults
The Restore Defaults option will set all user and administrative
parameters except License Option to their factory defaults.
PN: 1725-36034-001_B.doc
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
User-defined Preferences (Standby Menu)
The following user-defined preferences are also covered in the
SpectraLink 8002 Wireless Telephone User Guide. The system
administrator can refer to this list for more information about
customizing handset settings.
To configure the following options, the handset must acquire the
system (no error message may display) and be at the extension
display. This is the standby mode. While in the standby mode, press
and hold FCN briefly to open the user options menu. Use the
following keys to display and select options:
Display previous/next menu item.
Selects the menu item or option.
Selects the menu item or option.
Saves the entry.
Up/Down buttons:
Select button:
OK softkey:
Save softkey:
Bksp softkey:
Cncl softkey:
Up softkey:
Backspaces to allow editing of entry.
Cancels edit and return to previous menu level.
Returns to previous menu level.
Exits the menu (at the top level).
Exits to standby state (from any level).
Exit softkey:
End Call key:
Standby mode, options menu
Lock Keys
Ring Options
Phone Options
System Info
OK
Exit
34
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
Standby menu
Standby Menu Items
2nd Level
3rd Level
4th Level
Lock Keys
Ring Options
Off
*PBX
Continuous
Short Pulse
Long Pulse
*Tone 1
Tone 2
Tone 3
Tone 4
Tone 5
*Off
PBX
Continuous
Short Pulse
Long Pulse
*No Delay
5 Second Delay
10 Second Delay
[same as Telephone
Ring]
Phone Options
System Info
PN: 1725-36034-001_B.doc
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Standby Menu Items
2nd Level
3rd Level
4th Level
Firmware Version
* Default setting.
**Option appears when Ring Cadence and Vibrate Cadence are both set to a value other than “Off”.
(Additional options may be present. Contact your service representative for information.)
36
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
Lock Keys
When enabled, the Keypad Lock option will lock the keypad
immediately. If the keypad is locked, it may be unlocked by the end
user pressing the Unlk softkey and then the # key.
Ring Options
The Ring Option allows the user to set the ring for three separate
functions. Telephone ring is used for usual telephony functions. The
Auxiliary Rings may be used to set different ringing patterns for OAI
applications.
Telephone Ring
Telephone Ring allows the user to set a distinctive ring style, volume
and sequence. Select from an audible ring or a vibrate-only ring or a
vibrate ring along with or followed by an audible ring.
Ring Cadence The Ring Cadence is the rhythm of the ring. It may be set
to a pre-programmed ring cadence, or it may be set to obtain its
cadence from the proxy server. The PBX option is designed to utilize
any distinctive rings sent by the proxy server while allowing the user
to set unique rings for auxiliary applications.
Off: Silent
PBX: Proxy server determines ring cadence (e.g. the proxy server
may send rings that differentiate between internal and external
calls)
Continuous: Rings continually until answered
Short Pulse: Rings in short bursts
Long Pulse: Rings in long bursts
Ring Tone Select from five available tones (scroll to Tone 5 option). The
Play softkey allows the user to preview the tone before selecting. If
Ring Cadence is turned off, the Ring Tone option will not appear on
the menu.
Vibrate Cadence Vibrate Cadence options are the same as for Ring
Cadence (see above).
PN: 1725-36034-001_B.doc
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Ring Delay Ring Delay determines how long the vibrate cadence will
play before the audible ring starts. If Ring Cadence and Vibrate
Cadence are turned off, the Ring Delay option will not appear on the
menu.
Auxiliary Ring 1 and Ring 2
Auxiliary rings are designed to be utilized by OAI applications,
enabling the user to set a distinctive ring for these applications.
Phone Options
Noise Mode
Provides options that describe the noise level in your environment.
Changing this mode to High or Severe adjusts the handset’s
microphone and in-ear speaker volume to account for background
noise. Select Normal for most office environments; High for moderate
background noise; or Severe for extremely noisy conditions. If you use
High or Severe modes in a quiet environment, the person on the other
end of the line may find it difficult to hear your voice.
Key Tones
Key Tones may be turned on or off and determine whether tones play
when keys are pressed. Key Tones are enabled by default.
Warning Tones
The handset plays various Warning Tones such as system up or
down, out of range, etc. These tones may be turned on or off and are
enabled by default.
Display Contrast
The display may need to be adjusted for different lighting situations.
Contrast may be set by pressing the Up and Down side buttons until
the desired contrast is displayed and then pressing the OK softkey.
Keypad Autolock
The handset may be set to lock the keypad automatically when in
standby mode. The automatic locking function of the keypad may be
38
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephone Configuration
disabled (the default) or adjusted for a 5, 10 or 20-second delay before
locking.
System Info
Phone IP Addr
Displays the IP address currently assigned to the handset.
Server IP Addr
Displays the IP address of the SpectraLink OAI Server (if installed).
Firmware Version
Displays the software version running the handset. The MAC address
is the hardware identification number and is set at the factory. Three
code numbers correspond to the three files that each version uses.
Downloader: pd11gl3.bin
Functional: pd11wsd3.bin
Phintl: pi11001.bin
PN: 1725-36034-001_B.doc
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Software License and Protocol
Management
All SpectraLink 8002 Wireless Telephones are shipped from Polycom
with SIP software already installed. You may need to download and
install updates per the following instructions. The handsets may not
function properly without downloading updated software.
The following details the process to properly configure SpectraLink
8002 Wireless Telephones and download software via over-the-air file
transfer.
Requirements
•
A wireless LAN must be properly configured and operational
through the use of 802.11b wireless APs.
•
•
A TFTP server must be available on the network in order to load
the appropriate software into the handsets.
Finally, ensure that the Battery Pack on the handset is fully
charged.
PN: 1725-36034-001_B.doc
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Configuration Process
1. Download the latest SpectraLink 8002 Wireless Telephone
software from
2. Download the latest version of the SIP code and place it on the
TFTP server and ensure the TFTP server is started. The five files
that are needed must be named:
slnk_cfg.cfg
pd11wsd.bin
pd11wsd3.bin
pd11gl3.bin
pi110001.bin
3. Configure the handsets using the Admin menu. See Chapter 2
SpectraLink 8002 Wireless Telephone Configuration for detailed
configuration instructions.
a
b
c
Ensure the License Option menu option is set to 22.
Configure the SIP Registration settings.
If statically assigning IP addresses, ensure that the Phone IP
address, TFTP server IP, Subnet Mask, Default Gateway, and SIP TFTP
server IP addresses are accurate. If using a DHCP server, ensure
that appropriate options are set for the TFTP server.
d
Ensure the handset has properly configured ESSID. If you are
accepting broadcast ESSIDs at your APs, the handset will
automatically learn the ESSID information when powering on.
e
f
Set the Reg Domain.
Configure the handset security settings.
g
Set the Preferred Channels.
4. Power cycle the handset.
5. If the handset code needs to be updated, the SIP code will now
download to the handset. The status bar will increment fully
across the display for each function that is being performed in the
download process. Upon completion of the update process, the
handset will re-boot with the new firmware.
42
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Software License and Protocol Management
6. During the second download evolution, the handset receives code
from the TFTP server for system configuration and for its own
settings. Once this second evolution is complete, the handset is
ready to use.
For future software upgrades, simply update the files that are stored
on the TFTP server. Each time the handset is powered up, it will
check with the TFTP server to ensure it has the proper software
version.
PN: 1725-36034-001_B.doc
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Programming the SIP Handset
Features
In order for the handset to function in the SIP environment, it
downloads two files from the root directory of the SIP TFTP server
during startup. The first file contains generic system information and
is downloaded by every handset during the power-up sequence. A
second file, unique for each handset, is then downloaded. It contains
specific information for each handset such as username, password,
and line appearances. Example files are available for download.
Both of these files must be created or the example files must be
customized according to the site’s configuration. This is usually done
by the system integrator or administrator.
SIP TFTP Server Configuration Files
The two file types, generic and specific, are identical in format. Any or
all of the configuration information can be contained in either file.
Any information in the specific file that conflicts with the information
in the generic file will take precedence over that in the generic file.
Authentication information will be accepted from both files. For ease
of administration, it is recommended both file types be utilized and
that common settings be placed in the generic file..
Guidelines
•
The files are in plain text, US-ASCII. The general form of the
configuration file data is “parameter = value.”
•
•
The generic filename must be SIP_allusers.cfg.
Each specific filename must have the form of SIP_[username].cfg
where [username] is as assigned to each individual user by the
system administrator (e.g. sip_3001.cfg). See SIP Registration in
Chapter 2 SpectraLink 8002 Wireless Telephone Configuration
,
section The Admin Menu.
PN: 1725-36034-001_B.doc
45
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
•
•
•
•
Username requirements are: alphanumeric, no spaces, no
punctuation, case is ignored, 1-16 characters.
The generic file should contain proxy server information and
other SIP system data.
The specific file should contain data specific to each user such as
authentication credentials and line appearance data.
Some parameter lines accept more than one value, separated by a
colon or semicolon character as defined in the following table.
•
•
Any line that begins with a pound sign (#) is ignored.
In general space characters are ignored. Space characters may be
included in string values by replacing the space with “%20.”
•
•
If necessary, other special characters may be included by using a
hexadecimal representation: (%hh) where hh is the representation
of the character.
The lines in the .cfg file may appear in any order although
maintenance may be simplified by preserving the order in the
supplied example file.
Create or modify each of the files according to the following
instructions.
The generic file (sip_allusers.cfg)
The generic configuration file provides system information common
to all handsets.
The handset-specific files (e.g. sip_3001.cfg)
The handset-specific configuration file provides specific information
for the handset to identify itself and communicate to other phones.
Each handset must have its own file with a unique filename. You may
use the same parameters as the generic file when programming the
handset files if you wish to override a common setting.
You must configure a unique handset file for each handset being
deployed. Typically each of these files is named with the extension
number or name of the person assigned the handset. For example
John Doe’s handset could have a handset filename of
sip_JohnDoe.cfg.
46
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the SIP Handset Features
Proxy server commands
Use the following parameters when programming the configuration
files. See the sample configuration files following this table for more
detailed information.
Parameter
Value
Description
Notes
PROXYn_ADDR
xxx.xxx.xxx.xxx:ppp Proxy address. One n = 1, 2, 3
p
proxy
address
is
xxx.xxx.xxx.xxx = IP address
required but additional
proxy addresses may
be used to register
pppp = port (optional, 5060 is
the default)
or
secondary
line
appearances.
proxyname:pppp
Domain name
proxyname = proxy server
name (DHCP only)
PROXYn_DOMAIN
Domain served by this n = 1, 2, 3
proxy server.
DOMAIN
=
[example:
spectralink.com]
Can be omitted if a specific
proxy domain name is not
defined at the proxy server. If
omitted, defaults to the IP
address of the proxy server
(see above)
PROXYn_TYPE
Asterisk
SER
Specify
the Used by the handset to
manufacturer of each perform proxy-specific actions
defined proxy server.
based on known behavior for
specific proxy types. Omit this
parameter if the value is not
Asterisk or SER.
PROXYn_KEYPRESS_2 *enable
Controls generation of n = 1, 2, 3
in-stream RFC2833
833
disable
formatted key press
events. Match what is
required by your PBX.
See RFC2833. See
config file example for
more information.
*default (in example
file)
Must be disabled for OAI.
PROXYn_KEYPRESS_I enable
NFO disable
Controls generation of n = 1, 2, 3
SIP INFO requests to
the SIP server for
Must be enabled for OAI.
keypress
events.
Normally enabled.
PROXYn_REREG_SEC 35
seconds
to The requested n = 1, 2, 3
expiration interval in
S
3600 seconds
If the server has a lower
maximum setting or a higher
REGISTER
request
PN: 1725-36034-001_B.doc
47
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Parameter
Value
Description
Notes
messages.
minimum setting than that
requested,
the
server
response takes precedence.
*default
seconds
3600
See example file
PROXYn_KEEPALIVE_S 0 or 10 to 3600 Specifies
that
handset should send
keepalives to the
PROXYn server.
the n = 1, 2, 3
ECS
seconds
The
keepalive
interval
defaults to ZERO which
disables the feature.
*default = 0
When specified, the interval
can be set to zero or to 10 to
3600 seconds.
If a keepalive fails to get a
response within the SIP 32
second
timeout,
then
keepalives are terminated
until the next successful
registration to the proxy.
See example file
PROXYn_HOLD_IP0
*enable
disable
Controls setting of the n = 1, 2, 3
media
stream
IP
Use for compatibility with
older SIP servers that may
not recognize newer stream
attribute
HOLD status.
destination address to 0
(zero) when a call is put
on hold. See config file
*default (in example
file)
parameters
for
example
for
more
information.
PROXYn
_MAIL_SUBSCR
xxx
handset
subscribe
notification. See config
file example for more
information.
should
for mail
name = mail server contact
name.
or
xxx.xxx.xxx.xxx = IP address.
sip:name@domain
Domain where the mail
S
xxx
handset should invite to
access the mail center.
This is the main
voicemail dial number.
name = mail server contact
name.
xxx.xxx.xxx.xxx = IP address
or
1 For mail notifications, in general you will need to define only one contact parameter for each proxy. If the proxy server
automatically creates and renews subscriptions when the handset registers, then only the PROXYn _MAIL_NOTIFY contact need be
specified. If the handset must subscribe to a particular contact to get mail notification, then only the PROXYn_MAIL_SUBSCR
contact needs to be specified.
48
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the SIP Handset Features
Parameter
Value
Description
Notes
sip:name@domain
Domain where the mail
resides.
PROXYn
_MAIL_NOTIFY
xxx
mail
notification
name = mail server contact
name.
originates. See config
file example for more
information.
xxx.xxx.xxx.xxx = IP address.
or
sip:name@domain
Domain where the mail
resides.
AUTH
username;password Credentials.
username = The dial number
or string that identifies the line
appearance. Generally an
extension or phone number.
[see warning note below]
In general credentials
are needed for each
password
password created by
system administer
=
a
secure
the
which
enables a handset to register
and/or function.
CODECS
LINEn
codec1, codec2
username
Comma-separated list Defaults to “g711u, g711a”. if
of supported codecs in either is omitted it will be
order of preference.
added to the end of the list.
The dial # or name.
n = 1, 2, 3, 4, 5
The
registered
contact
becomes:
sip:username@domain
LINEn _PROXY
LINEn _CALLID
i
SIP proxy server for this n = 1, 2, 3, 4, 5
line.
i = the number of the proxy
server 1, 2, 3.
callerid
String that displays at n = 1, 2, 3, 4, 5
the far end.
callerid = the text that will
display as the caller ID on the
called handset.
2 WARNING: providing credentials by using the AUTH parameters in the configuration files is a security risk and should be
avoided by entering usernames and passwords in admin menu or by allowing the user to login at startup time. Credentials entered
here are in plain text and accessible by anyone who can access the TFTP server files. Credentials stored in the SIP server or in the
handsets are protected.
PN: 1725-36034-001_B.doc
49
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Parameter
Value
Description
Notes
FAVORITE
Dialstring;identifier Phonebook
numbers
list
of Up to 8 entries permitted
accessible which
may
be
divided
from
the
Favorites between generic and phone
menu. Favorites in the specific files.
allusers file will be
Dialstring = complete SIP URI
or local extension #
present in the Favorites
on all handsets. See
config file example for
more information.
Identifier = name. If omitted,
the dial string appears on
Favorites menu.
50
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the SIP Handset Features
Sample Configuration Files
Configuration files are illustrated below. These files are available as a
download from the software updates site and may be customized for
your application. Please note that these are merely samples and will
not work on your system as written here or as downloaded. Your
configuration files must be locally programmed according to your site
requirements.
SIP_allusers.cfg
# SIP ALL USERS Configuration file example
# Configuration file format example with explanatory text
# Codec preference order only. This does not enable/disable codecs
# (Optional)
# can be G.711-ulaw, g.711u, G.711U, g711u, G.711U, etc.
# if g711u is omitted it will be added to end of list.
# if g711a is omitted it will be added to end of list after u.
CODECS = g711u, g711a
# One PROXYn (PBX/Call Server) is required, additional ones are optional as
# you can register secondary line appearances with other PROXY servers
PROXY1_ADDR
#PROXY2_ADDR
= 10.0.0.138:5060
= 172.29.0.140:5060
#ProxyDomain can be omitted if a specific proxy domain name is not defined at
the
# proxy server. If omitted, the ProxyDomain defaults to the IP address of the
# proxy server.
# (below are examples of different ways to specify a domain)
#PROXY1_DOMAIN = plcmengr.com
#PROXY1_DOMAIN = 10.0.0.138
#PROXY1_DOMAIN = axlx.engr.local
# PROXY1_MAIL_SUBSCR is who we should subscribe to for mail center
# notifications
# This is needed only if the user is not subscribed automatically at
# registration.
# It is almost never required in current versions of Asterisk to specify
# this.
# If you are using Asterisk (non-business edition) before v1.2, this is
# necessary.
# This example is actually specific for a line number:3001
#PROXY1_MAIL_SUBSCR = sip:[email protected]
PN: 1725-36034-001_B.doc
51
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
# PROXYn_MAIL_NOTIFY is from whom we might get unsolicited mail center
# notifications
# This option is deprecated and no longer needed in versions beyond
# e/h340/i640 phones v108.011, Polycom 8002 phones v130.001, and Polycom
# 8020/8030 phones 131.001.
# Examples:
#PROXY1_MAIL_NOTIFY = [email protected]
#PROXY1_MAIL_NOTIFY = sip:[email protected]
# PROXY1_MAIL_ACCESS is the main voicemail dial number
# Examples:
# PROXY1_MAIL_ACCESS = 7999
# PROXY1_MAIL_ACCESS = sip:[email protected]
# PROXY1_MAIL_ACCESS = [email protected]
PROXY1_MAIL_ACCESS = 7999
#PROXY1_KEYPRESS_2833 controls generation of in-stream RFC2833 formatted key
# press events. Normally you want this to be disabled for Asterisk but it
# depends on your configuration and what you want to be able to do.
# If you are going to do OAI integration, this must be disabled.
# The default is disable
PROXY1_KEYPRESS_2833 = disable
#PROXY1_KEYPRESS_INFO controls generation of SIP INFO requests to the SIP
# server for keypress events. Normally you want this to be enabled.
# If you are going to do OAI integration, this must be enabled.
# The default is enable
PROXY1_KEYPRESS_INFO = enable
# PROXYn_HOLD_IP0 controls setting of media stream IP destination to 0.0.0.0
# when a call is put on hold.
# PROXYn_HOLD_IP0 is not required for current versions of Asterisk.
# For older PBXs that require this, set this to enable
#PROXYn_HOLD_IP0 = enable
# PROXY1_PRACK enables ACK'd provisional responses to INVITE requests. The
# PRACK mechanism will be used if this switch is enabled and the Proxy server
# specifies support for the PRACK mechanism. PRACK is NOT SUPPORTED in
# current versions of Asterisk, but is to be supported on subsequent
# versions. PRACK should not be required on local area networks.
PROXY1_PRACK = disable
# PROXYn_KEEPALIVE_SECS specifies that the phone should send Keep alives to
# the PROXYn server. It can be set to 0 or anywhere from 10 to 3600
# seconds. The default value (which is applied if no parameter is supplied
# in this file) is 0 which means the phone will not send keep_alives to
# PROXYn.
# If the phone fails to get a keepalive response within the SIP 32 second
# timeout, the keepalives are terminated for that PROXY until the next
# successful registration to the PROXY.
#
# This parameter is REQUIRED on Asterisk Business Edition with the Polycom
# 8002 phone but not with the Polycom 8020/8030 phones. This is because
52
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the SIP Handset Features
# Linux, the OS running Asterisk, has a ARP Cache flushing mechanism. This
# feature serves to refresh the ARP Cache for the 8002 phones. For 8020 and
# 8030 phones, the ARP Cache is refreshed by the SVP server. 8020/8030
# phones do not know how to parse this parameter.
#
# The value of this parameter for 8002 phones should be just less than the
# minimum ARP Cache flushing time on the Linux box running Asterisk. For
# Redhat this minimum flushing time is 15 seconds, so the parameter needs to
# be set for 14 seconds or less. For other Linux Distributions, you may
# have to determine what this minimum value is, however 14 seconds should
# work fine.
#
# The lower this setting, the more the impact on the 8002's standby battery
# life.(8002 phones running version 130.003 and earlier code ignore this
# parameter if present)
# (8020/8030 phones ignore this parameter if present no matter the SW
# version)
PROXY1_KEEPALIVE_SECS=14
# PROXYn_REREG_SECS specifies the re-registration interval for a PROXY.
# This is the requested expiration interval sent in the REGISTER request
# message. It can be set to anything between 35 and 3600 seconds.
# The default value (which is applied if no parameter is supplied in this
# file) is 3600 which means the phone will attempt to register every 3580
# seconds, if the server's response interval doesn't take precedence (see
# below).
#
# If the server has a lower maximum setting or a higher minimum setting that
# this value then the server's response will take precedence and this
# parameter will be ignored.
#
# The phone will always attempt to re-register with the PROXY 20 seconds
# prior to the expiration interval. Thus, if this parameter is set to 35
# seconds, and the server's response interval doesn't take precedence, then
# the phone will attempt to re-register every 15 seconds.
#
# The lower this setting, the more the impact on the 8002's standby battery
# life.
# (8002 phones running version 130.003 and earlier code ignore this
# parameter if present)
#(8020/8030 phones ignore this parameter if present no matter the SW version)
PROXY1_REREG_SECS=3600
# Favorites in the allusers file will be present in the favorites on all
# handsets
# The username can be blank and can include escaped chars
# Useful features can be included such as call forwarding or dialing
# voicemail
# FAVORITE = dial_string; username
FAVORITE = 1234; Site Security
FAVORITE = *98; Call Forwarding
PN: 1725-36034-001_B.doc
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Sample handset-specific file
# Configuration file format example
# Codec preference order only. This does not enable/disable codecs.
# (Optional) can be G.711-ulaw, g.711u, G.711U, g711u, G.711U, etc.
# if g711u is omitted it will be added to end of list.
# if g711a is omitted it will be added to end of list after u.
#CODECS = g711u, g711a
# One PROXYn (PBX/Call Server) is required, additional ones are optional as
# you can register secondary line appearances with other PROXY servers
#
#PROXY1_ADDR
#PROXY2_ADDR
= 10.0.0.138:5060
= 172.29.0.140:5060
# ProxyDomain can be omitted if a specific proxy domain name is not defined
# at the proxy server. If omitted, the ProxyDomain defaults to the IP address
# of the proxy server.
# (below are examples of different ways to specify a domain)
#PROXY1_DOMAIN = plcmengr.com
#PROXY1_DOMAIN = 10.0.0.138
#PROXY1_DOMAIN = axlx.engr.local
# PROXY1_MAIL_SUBSCR is who we should subscribe to for mail center
# notifications
# This is needed only if the user is not subscribed automatically at
# registration.
# It is almost never required in current versions of Asterisk to specify
# this.
# If you are using Asterisk (non-business edition) before v1.2, this is
# necessary.
# This example is actually specific for a line number:3001
#PROXY1_MAIL_SUBSCR = sip:[email protected]
# PROXYn_MAIL_NOTIFY is from whom we might get unsolicited mail center
# notifications
# This option is deprecated and no longer needed in versions beyond
# 8002/e340/h340/i640 handsets v108.011, Polycom 8002 phones v130.001, and
# Polycom 8020/8030 phones 131.001.
# Examples:
#PROXY1_MAIL_NOTIFY = [email protected]
#PROXY1_MAIL_NOTIFY = sip:[email protected]
# PROXY1_MAIL_ACCESS is the main voicemail dial number
# Examples:
# PROXY1_MAIL_ACCESS = 7999
# PROXY1_MAIL_ACCESS = sip:[email protected]
# PROXY1_MAIL_ACCESS = [email protected]
#PROXY1_KEYPRESS_2833 controls generation of in-stream RFC2833 formatted key
54
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Programming the SIP Handset Features
# press events. Normally you want this to be disabled for Asterisk but it
# depends on your configuration and what you want to be able to do.
# The default is disable
#PROXY1_KEYPRESS_2833 = disable
# PROXY1_KEYPRESS_INFO controls generation of SIP INFO requests to the SIP
# server for keypress events. Normally you want this to be enabled.
# The default is enable
#PROXY1_KEYPRESS_INFO = enable
# PROXYn_HOLD_IP0 controls setting of media stream IP destination to 0.0.0.0
# when a call is put on hold.
# PROXYn_HOLD_IP0 is not required for current versions of Asterisk.
# For older PBXs that require this, set this to enable
#PROXYn_HOLD_IP0 = enable
# PROXY1_PRACK enables ACK'd provisional responses to INVITE requests. The
# PRACK mechanism will be used if this switch is enabled and the Proxy server
# specifies support for the PRACK mechanism. PRACK is NOT SUPPORTED in
# current versions of Asterisk, but is to be supported on subsequent
# versions. PRACK should not be required on local area networks.
#PROXY1_PRACK = disable
# ////////////////////////
# ////// ABOVE this line should probably be in the sip_allusers.cfg file
# ////// with items uncommented in this file only for overriding a setting
# ////// for a particular user.
# ////////////////////////
# Authentication credentials
# (Normally not stored in this file for security reasons)
# AUTH = username; password
AUTH = 3001; 3001
# Line definitions
# Each definition should have LINEn, LINEn_PROXY and LINEn_CALLID
# LINEn is the dial number
# LINEn_PROXY is the PROXYn server this line should register with, typically
# defined in sip_allusers.cfg.
# LINEn_CALLID is shown on the standby display of 8020/8030 phones but not
# 8002 or e/h340/i640 phones. The Asterisk Server converts the callID
# information to alternative forms defined in the Asterisk configuration
# files for display at the far end of a phone call.
# Up to 5 line definitions can be made for each user
# Line definitions do not necessarily have to have different extensions
LINE1
= 3001
LINE1_PROXY = 1
LINE1_CALLID = Mouse, Mickey
# Two lines may map to the same extension to allow second incomming calls.
LINE2
= 3001
LINE2_PROXY = 1
PN: 1725-36034-001_B.doc
55
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
LINE2_CALLID = Brady, Marsha
LINE3
= 3002
LINE3_PROXY = 1
LINE3_CALLID = Drew, Nancy
#LINE4
= 804
#LINE4_PROXY = 3
#LINE4_CALLID = Sip User 4
#LINE5
= 1014
#LINE5_PROXY = 2
#LINE5_CALLID = Sip User 5
# Favorite Dialed Number list.
# You can define up to 8 total entries including any defined in
# sip_allusers.cfg.
# You can enclose a string in quotes to allow for spaces.
# Each favorite can be complete SIP URI
# Format is:
# FAVORITE = dial_string; username
#
# The username can be blank and can include escaped chars.
FAVORITE = 3001; Bob
FAVORITE = 3032; Jill in Accounting
FAVORITE = 3013; SoundPoint 3013
FAVORITE = 3020; Jane
FAVORITE = 93035551212; Richard's Cell
56
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Using the SIP Handset
The Handset Display
Overview
When active, the handset screen has six rows that display information
in this format:
Row # Information provided
1
2
3
4
5
6
Icons
Line number
Instructions
Call one info
Call two info or dial aids
Softkeys
Row 1 displays signal, battery, voicemail and line number icons. Row
2 displays the line number of the line for which information is being
displayed. Row 3 displays instructions where needed. Two calls are
permitted on each line. Row 4 displays information for call one and
row 5 displays information for call two. Row 5 is also used to provide
dialing aid for call one. Row 6 displays available softkeys.
The SpectraLink 8002 Wireless Telephones support a two to four line
display of up to 19 alphanumeric characters. Display information
provided by the proxy server when the handset is off-hook, such as
calling party identification, will be processed and put on the handset
display.
Line indicators
The line indicators on the handset will convert to a solid or flashing
number to indicate the line is in use or ringing. The number or text
PN: 1725-36034-001_B.doc
57
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
associated with the line is displayed on the handset by pressing the
LINE key.
Handset icons
Indicator
Function
The signal-strength icon indicates the strength of the signal from the AP and can
assist the user in determining if the handset is moving out-of-range of that AP.
The voicemail icon is activated when a new voicemail message is received if the
feature is supported by the proxy server.
The battery icon indicates the amount of charge remaining in the Battery Pack.
When only one bar remains, the Battery Pack should be charged.
Locked
Locked indicates that the keypad is locked to prevent accidental activation. Use
the Unlk softkey plus the # key to unlock it.
[No
message]
Service If warning tones are not disabled, a falling tone alarm will sound and a
descriptive message displays when the handset cannot receive or place calls.
You may be outside of the covered area. Walk back into the covered area. The
in-service rising tone indicates service is reestablished.
The download icon indicates that the handset is downloading code. This icon
only appears while the handset is running the over-the-air downloader. It
appears to the right of the signal strength icon in the same location as the
voicemail icon.
Signal strength
The signal-strength icon indicates the strength of the signal from the
AP and can assist the user in determining if the handset is moving out
of range. It is always present on the display in the upper left corner.
Battery charge
The battery icon indicates the amount of charge remaining in the
Battery Pack. There are three levels and when only one level remains,
the Battery Pack needs to be charged. It is always present on the
display in the upper right corner.
Voicemail
The voicemail icon is activated whenever any of the specified mail
subscribers/notifiers (see SIP configuration files) sends notification to
the handset that new messages are available. By activating the LINE
menu, and observing which lines are flagged with a plus (+) sign, the
user can determine which proxy has outstanding mail.
The system administrator defines access to voicemail.
58
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SIP Handset
Download
Indicates that the handset is checking for or downloading code. This
icon only appears while the handset is running the over-the-air
downloader. It appears to the right of the signal-strength icon in the
same location as the voicemail icon.
Ringing and tones
The ringing type (normal or vibrate) is selected by the handset user.
The audible and vibrating ringer on the handset will follow the
protocol command provided by the PBX via the proxy server if the
user selects PBX cadence described in the User-defined Preferences
section.
Handset modes
Standby mode (on-hook)
In standby mode, the handset is waiting for an incoming call or for
the user to place an outgoing call. The extension number is shown on
the display and there is no dial tone. In this mode, the handset is
conserving battery power and wireless LAN bandwidth.
By default, the username assigned to line 1 is displayed on the
standby screen.
Active mode (off-hook)
When an incoming call occurs, the handset will ring, and the handset
enters the active mode. The handset will ring according to user
preference as specified in the standby menus. The ringing can be
silenced by pressing the End Call key. If you do not wish to accept the
call, press the Rej softkey. The SIP server (if present) will redirect the
call as configured by the system administrator, often to voicemail.
(Treated like the handset is busy.)
The handset is in the active mode when an incoming call is answered
by pressing the Start key or when it is in communication with the SIP
server without being in an active call.
When an incoming call occurs during an active call, the handset will
play the second call ringing sound until the call is answered, the caller
hangs up, or the call transfers to voicemail. If End Call is pressed, the
first call is terminated and the handset reverts to a full ring.
PN: 1725-36034-001_B.doc
59
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
The active modes utilize the most bandwidth and battery power. To
conserve these resources, return the handset to the standby mode
when a call is completed by pressing the End Call key.
Messaging mode
If text messaging functions have been programmed, as in a nurse call
system, the handset is able to receive text messages. While these
messages are being accessed, the handset is in messaging mode.
Incoming calls will ring with the second call ringing sound.
Messaging mode uses more battery power than standby mode, but
less than Active mode.
Softkeys
Softkey functions change as the state of the handset changes. Softkeys
are displayed only when they are available to be activated. Softkeys
make common PBX functions available on the handset. For example, a
call may be placed on hold, the handset may be muted, and a second
line may be activated for an outgoing call or a second call on the same
line may be answered. Calls may also be transferred to another
number, either as a consulted transfer or without consult. Other
handset features (DND, Transfer) may be accessed by pressing the
FCN key.
Number dialing may be specified as alpha or numeric code by
pressing Start Call plus the MENU key. Select Alpha Dialing if letters and
symbols are to be entered in the dialing string.
Softkey Name
Displayed…
Press to…
Answ
Answer
When a call is incoming on Answer the call (equivalent to
the selected line.
START key).
Bksp
Backspace character
Entering a dial number.
Delete the character prior to the
cursor position.
Back
Del
Back one screen
Delete
Displaying a menu.
Editing dial number.
Exit the menu.
Delete the character to the left of
the cursor.
Dial
End
Favr
Dial Call
End Call
Favorites
A
dial number is being Initiate
a
phone call to the
entered on the selected line. entered dial number.
An active call on the selected Terminate the call without going
line. back to standby mode.
Prior to entering the first Activate the Favorites menu.
character of a dial number.
60
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SIP Handset
Softkey Name
Displayed…
Press to…
Fwd
Forward Definition
Prior to entering the first Delete
a
previously defined
character of a dial number.
In an active call.
forward destination.
Or initiate definition of a new
forward destination.
Hold
Msg
Hold
Place the call on hold. The line
status shows x when the call is
on hold or * when audio is
flowing.
Message
Initial dial screen when new Initiate a call to the specified
line is selected and a dial message center contact address
tone is active prior to for retrieval or administration of
entering first character of the voicemail.
number to be dialed3.
Mute
OK
Toggle muting
OK
When in an active call.
Toggle audio transmission to the
far end. The line status shows *
when not muted or x when
muted.
Power up registration if Send
the
username
and
username is not configured password to the SIP server for
in admin menu.
authorization to register the
handset.
Redl
Rej
Redial
Reject
Prior to entering the first Redial the last number that was
character of a dial number. dialed.
Incoming call on the selected Reject the incoming call. The SIP
line.
server will then redirect the call
elsewhere if configured to do so.
Rsme
Save
Resume
Save
In an active call and you Resume
have placed the call on hold previously placed on hold or that
or in standby mode if any call went on hold when another line
a
call that was
is on hold.
was activated.
Entering a dial number as a Save the dial number as the
forward destination.
forwarding destination for the
selected line.
3 Appears only if the PROXYn_MAIL_NOTIFY is configured. A message center contact address must be defined for the proxy used
by the selected line.
PN: 1725-36034-001_B.doc
61
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Menus
Line menu
The Line menu allows you to activate a call on a selected line or to
view the status of lines.
View the five line appearances by pressing the LINE key. The line
number and extension number of the first four lines are displayed.
Press the LINE key again to view the fifth line. Active lines are in bold
face. Defined but unregistered lines are faded. Lines that have been
forwarded are prefixed with the greater-than character (>) followed
by the forwarding destination.
Pressing the LINE key from the active mode displays a menu of line
appearances as programmed in the SIP TFTP configuration file. The
LINE key can be pressed while the handset is in the standby mode to
activate the handset and to activate a new call on the selected line.
The currently selected line is indicated by an asterisk (*). Lines for
which the corresponding proxy server has outstanding new mail are
flagged with plus (+) characters. Lines that should be registered to a
proxy but have failed registration for any reason are displayed in
faded text and are not selectable from the menu.
Exit the LINE display by pressing a line number key to start a new call
on the selected line and put any other call on hold, or by pressing the
End Call key to exit without starting a new call. Press the More softkey
to page through additional items on the Line menu.
Favorites menu
The Favorites menu provides access to a predefined list of dial
numbers. The list is programmed by the system administrator and
may include common or handset-specific entries. For handset-specific
entries, the user must provide a list of numbers to the system
administrator for programming. Numbers on the Favorites list cannot
be programmed in or through the handset by the end user.
The Favorites list can include either complete dial numbers for named
parties or partial numbers that need additional data entry. Here is a
partial entry example: If a PBX feature access code for call forwarding
is defined in the Favorites list but you need to add the forwarding
62
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SIP Handset
destination information before sending the call to the PBX to activate
the feature, you can create a Favorite with the access code only.
Access the Favorites list while in a dialing state by pressing the Favr
softkey to display a menu of pre-defined numbers or names that can
be dialed (as programmed in the SIP TFTP configuration file.) When
an item is selected from the list, the dial number is displayed. You
may edit or add digits to the displayed number if necessary before
pressing START to place the call. When using the Favorites menu to
perform a blind transfer to someone on the list, select an entry from
the Favorites menu and then press FCN and select Transfer.
FCN menu
Pressing the FCN key from the active mode displays a list of telephony
options available to the user. Included here are transfer and do-not-
disturb functions.
The FCN menu is accessible while in the active mode and provides
these features:
Transfer
Do Not Disturb
Set/Clear Forward
[defined option 1]
OAI functions are automatically added as items at the
end of this menu if defined on an OAI server.
[defined option 2]
[defined option 3]
Items on this menu are accessible through navigation and selection
keys or through short-cut keys as displayed with the menu items.
MENU display
Pressing the MENU key from the active mode allows you to set the
dialing mode to either numeric only or alphanumeric entry.
PN: 1725-36034-001_B.doc
63
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Handset Operation
Alphanumeric dialing
During dialing the carat (^) indicates the insertion point for the next
character. Up to 80 characters may be entered with automatic
scrolling. While in alphanumeric mode, alphabetic characters can be
entered by repeatedly pressing the 1 through 9 keys. Punctuation
characters are available by repeatedly pressing the asterisk (*), zero
(0) or pound (#) keys. Row 5 displays the available characters as the
key is pressed. Pausing will enter the highlighted character in the dial
string. A space character is available on the pound key or by pressing
the >> softkey when the insertion point is at the end of the dial string.
The << and >> softkeys may be used to position the insertion point for
editing the entry. Press the Dele softkey to delete the character prior to
the insertion point.
Feature activation
If you want to…
Then…
Turn the handset on
Press and hold the END key until two chirps sound.
Turn the handset off
Press and hold the END key. One chirp will sound. If you are in a call, hang
up first, then turn off the handset.
Unlock the keypad
Lock the keypad
Press the Unlk softkey, then #.
While in standby mode press FCN, then Select.
64
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SIP Handset
If you want to…
Then…
Place a call
1 Press the START key and wait for a dial tone.
2 Dial the numbers and press START. Listen for the ring to indicate the
alerting of the called party.
Note: Line 1 is the default line
Example:
1
Line 1 [your dial number]
*To: [dialed number]
Hold Rej
Mute
Place a second call on Only outgoing calls are permitted as the second call on a given line. If there
the same line
is an incoming call to the number assigned to the line, the caller will get a
busy tone and be routed to voicemail or to the second appearance of that
call number, if defined.
3 To access the second call dial tone, press LINE + [the line number].
4 Dial the number for the second call.
5 Press START to place the call.
6 When a second call is active on the same line appearance, the second
call appears below the first on the handset display.
7 Use LINE + [the line number] to toggle between calls. The selected call
is in bold type the other call is faded.
Example:
The following example shows an active incoming call as call one on line 1
(Fr or From) and an outgoing call on hold as call two on line 1 (To). The
bold text on row 4 indicates that call one is the currently selected call and
that any softkeys or menu functions will apply to call one. The asterisk (*) on
row 4 indicates that audio is currently flowing for call one.
1
Line 1 [your dial number]
*Fr: [caller ID of caller]
=To: [number you dialed]
Hold
Mute End
Place
different line
a
call on
a
8 Press START and listen for dial tone and then press LINE.
or to predial the number just press the LINE key.
9 Navigate to desired line and press Select.
10 Dial the number.
11 Press the Dial softkey or START to initiate the call.
PN: 1725-36034-001_B.doc
65
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
If you want to…
Place call
Then…
a
from
12 Press START.
Favorites menu
13 Listen for dial tone.
14 Press Favr softkey.
15 Use the side buttons to find and select desired entry.
16 Edit entry if needed.
17 Press START to place the call.
Answer/Reject a call
When the handset rings, the line’s icon will flash and row 2 will display the
line number and your dial number. Row 4 will display Fr (From) and the
caller ID of the incoming call.
18 Press START or the Answ softkey to answer the call.
or
19 Press Rej to reject the call and allow the SIP server to redirect the call
elsewhere, usually to voicemail.
Example:
1
Line 1 [your dial number]
Fr: [caller ID]
Answ Rej
When the call is answered an asterisk (*) displays at the start of row 4 which
indicates that this line is in an active call with established audio connection.
The softkeys for Hold, End and Mute appear.
Example:
1
Line 1 [your dial number]
*Fr: [caller ID]
Hold
Mute End
66
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SIP Handset
If you want to…
Then…
Place a call on hold
Press the Hold softkey.
When a call is placed on hold, an equal character (=) replaces the asterisk
(*) and the Rsme softkey replaces the Hold softkey. Press Rsme to return to
the call.
Example:
1
Line 1 [your dial number]
=Fr: [caller ID]
Rsme
Mute End
Press the Mute softkey. When the handset is muted, an x character replaces
the asterisk (*). Press the Mute softkey again to restore audio pickup.
Mute/Unmute a call
Silence the ring
Press the END key to silence the loud ring and convert it to in-ear ringing.
Loud ringing will resume when the next incoming call is received while the
handset is in standby mode.
Answer
second line
a
call on a If another call comes in on a different line, the called line icon flashes and a
tone sounds in the audio stream. In this example, a call is coming in on line
2 and the line 2 icon is flashing.
Example:
1 2
Line 1 [your dial number]
*Fr: [caller ID]
Hold
Mute End
20 To view the caller ID of the incoming call without interrupting the active
call, press LINE + [the line number]. The display now shows information
about the incoming call and you will continue hearing audio on the first
call.
Example:
1 2
Line 2 [your dial number]
Fr: [caller ID]
Answ Rej
21 Press Answ or START to answer the incoming call and place the active
call on the other line on hold. Pressing the Rej softkey will redirect the
incoming call to voicemail or as otherwise programmed.
PN: 1725-36034-001_B.doc
67
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
If you want to…
Then…
Transfer a call (blind)
22 While in a call, press FCN and then select Transfer (or press the
shortcut key 1). (The current call will be placed on hold]. A new call will
be started and you will hear a dial tone.)
23 Press the digits for the number to which you wish to transfer the call or
press the Favr softkey and select an entry from the Favorites menu..
24 Press FCN 1 again. The call will be transferred to the number that you
have entered and your call will be disconnected.
Transfer
(consulted)
a
call
25 While in a call, press FCN and then select Transfer (or press the
shortcut key 1). (The current call will be placed on hold]. A new call will
be started and you will hear a dial tone.)
26 Press the digits for the number to which you wish to transfer the call or
press the Favr softkey and select an entry from the Favorites menu..
27 Press Dial to establish a second call.
28 When the party answers, have your conversation and then press FCN 1
to transfer the held call and disconnect the first call and return to
standby mode.
Transfer a call to another
call already on Hold
29 While in a call, press FCN and then select Transfer (or press the
shortcut key 1). The current call will be placed on hold and you can
converse with the party on the second line.
30 Have your conversation and then press FCN 1 to transfer the held call
and disconnect the first call and return to standby mode.
Forward all calls
Calls may be forwarded on a per-line basis. The LINE display will indicate if
a line is forwarded by a > character followed by the destination address. If
any line is forwarded, the standby screen will display forwarding status. If
the do-not-disturb feature is enabled, the forwarding status will be pre-
empted by the Do Not Disturb display.
31 Press LINE + [the line number].
32 Press the Fwd softkey and enter the forwarding destination.
33 Press the Save softkey to save the forwarding destination.
If a given contact number has multiple appearances on the handset, forward
the lowest line appearance. All calls to that number on any line appearance
will then be forwarded.
Clear forwarding on a
line
34 Press LINE + [the line number],
35 Press the Fwd softkey and enter the forwarding destination.
36 Press the Fwd softkey again.
68
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the SIP Handset
If you want to…
Then…
Listen to voicemail
When any proxy has outstanding messages, the voicemail icon will display.
The LINE menu will display a plus (+) indication when there is a new
voicemail for that line. Indications are cleared when the handset receives
notification that all new voicemail messages have been read.
37 Press START and dial the number assigned to message retrieval and
press START again.
38 Follow system instructions to retrieve messages.
Alternately, if a PROXYn_MAIL_ACCESS value has been configured for the
corresponding proxy, the voicemail system can also be accessed by
pressing the Msg softkey, which will appear after selecting a line and before
beginning to dial.
Do Not Disturb
Press FCN 2. The handset will not ring for new incoming calls.
(reject all incoming calls)
When the do-not-disturb feature is enabled, the standby screen will display
Do Not Disturb.
Press FCN 2 again to resume ringing for new incoming calls.
Clear Do Not Disturb
Redial the last number
you dialed
39 Press START.
40 Press Redl.
41 Verify that the displayed number is the one you want and the line # is
valid.
42 Press START.
Activate a registered OAI
function on an OAI
server
43 Press START.
44 Press FCN.
45 Navigate to desired OAI function using Up and Down buttons.
46 Select the OAI function using the Select button or shortcut key.
Silence while ringing
Press the END key to silence the ring.
Adjust
headset volume
the While the headset is plugged in, press the up/down volume buttons on the
side of the handset during the call.
End the call
Press the END key to return to the standby mode.
Turn on the backlight
The backlight comes on when any key is pressed or when there is an
incoming call, and stays on for 10 seconds. It turns off if another key is not
pressed for 10 seconds.
PN: 1725-36034-001_B.doc
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Testing a Handset
Verify proper registration and operation of each handset by
performing the following tests on each handset in an active wireless
area.
1. Power on the handset by pressing the END key. A series of
messages will be displayed as the handset acquires the system.
The handset should display the user extension.
2. Place a call and listen to the audio quality. End the call by pressing
the END key.
3. Place a call to the handset and verify ring, answer, clear transmit,
and clear receive audio.
4. Use the softkeys to verify all softkey programmed features on the
handset.
5. Press the END key. Any line indicators should turn off and the
extension number display will return.
If any of these steps fails to operate as described, refer to Chapter 10
Troubleshooting for corrective action.
PN: 1725-36034-001_B.doc
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Diagnostic Tools
Run Site Survey, Diagnostics Mode and Syslog Mode are three diagnostic
tools provided to assist the WLAN administrator in evaluating the
functioning of the handset and the system surrounding it. Diagnostic
tools are enabled in the Admin menu.
Site Survey
Site survey can be used to evaluate the facility coverage before
certifying that an installation is complete. It can also be used at any
time to evaluate coverage by testing signal strength, to gain
information about an AP, and to scan an area to look for all APs
regardless of ESSID. The information available through the site
survey includes:
•
•
•
ESSID
Beacon Interval
Information regarding support of 802.11d, 802.11g, 802.11h, and
other 802.11 amendment standards as required.
•
Current security configuration
Start the site survey by selecting Run Site Survey from the Admin menu.
The mode starts immediately.
When the site survey is started, it is by default in “single ESSID”
mode. When the Any softkey is pressed (softkey A), all APs regardless
of ESSID are displayed, and the softkey changes to say MyID. Pressing
the MyID softkey will revert to the “single ESSID” mode and change
the softkey back to Any.
The display has the following layout for “single ESSID” mode.
1 1 1 1 1 1
1 1 1 1 1 1
1 1 1 1 1 1
1 1 1 1 1 1
- 2 2
- 2 2
- 2 2
- 2 2
3 3
3 3
3 3
3 3
4 4 4
4 4 4
4 4 4
4 4 4
PN: 1725-36034-001_B.doc
73
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
A n y
D e t l
Where:
•
111111 = The last three octets of the on-air MAC address for a
discovered AP.
•
•
•
•
22 = The signal strength for the specified AP.
33 = The channel number of the specified AP.
444 = The beacon interval configured on the specified AP.
Any/MyID = Softkey to toggle between “single SSID” and “any
SSID” mode.
•
Detl/Smry = Softkey to toggle between the multiple AP
(summary) display, and the single (detail) displays for each AP.
The following screen shows how the display would look when there
are three APs configured with an ESSID that matches that of the
handset. The first has a signal strength of –28 dBm, is configured on
channel 2, with a beacon interval of 100 ms. The second has a signal
strength of –48 dBm, is configured on channel 6, with a beacon
interval of 200 ms. The third has a signal strength of –56 dBm, is
configured on channel 11 with a beacon interval of 100 ms.
a b 7 b c 8
2 a e 5 7 8
2 a e 5 9 6
- 2 8
- 4 8
- 5 6
0 2
0 6
1 1
1 0 0
2 0 0
1 0 0
A n y
D e t l
When the “any ESSID” mode is selected, the summary display
contains the first six characters of the AP’s ESSID instead of the
beacon interval as in the example below. Also, the number of octets of
the APs BSSID is reduced to 2 octets.
a b 7 b
2 a e 5
2 a e 5
- 2 8
- 4 8
- 5 6
0 2
0 6
1 1
A L P H A
W S M T E S
v
o i c e
M y I D
D e t l
In detail mode the display would appear as follows. The left/right
arrow keys (* and #) will move between AP indices.
74
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Tools
i
:
b b b b b b
e e e e e e e e e e e
r r r r r r r r r r + x x x x
s n
c h
b c n
D G H I
r
r
r
m m m
A n y
G : g g g g
P : p p p p
S m r y
Where:
•
•
•
•
•
•
•
•
i = index of selected AP (value will be from 0 to 3 )
bbbbbb = the last three octets of the BSSID for a discovered AP
sn = signal strength in –dBm
ch = channel
bcn = beacon interval
eeeeeeeeeee = SSID (up to first 11 characters)
DGHI = 802.11 standards supported
rrrrrrrr = rates supported. Basic rates will have a “b” following the
rate
•
•
•
•
•
•
+ = more rates are supported than those displayed
xxxx = WMM or UPSD if those QoS methods are supported
mmm = security mode
G:gggg = group key security
P:pppp = pairwise key security
Any/MyID = softkey to toggle between “single SSID” and “any
SSID” modes
•
Detl/Smry = softkey to toggle between the multiple AP display
(summary), and the single AP display (detail)
Numbers scrolling across the handset display indicate AP information
is being obtained. A Waiting message indicates the system is not
configured properly and the handset cannot find any APs.
PN: 1725-36034-001_B.doc
75
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Solving coverage issues
Coverage issues are best resolved by adding and/or relocating APs.
Overlap issues may be resolved by reassigning channels to the APs or
by relocating the APs. See Chapter 10 Troubleshooting under Access
Point Problems for more information.
Diagnostics Mode
The Diagnostics Mode is used to evaluate the overall quality of the link
between the handset, AP, and infrastructure side equipment, such as
proxy server. Unlike site survey, the Diagnostics Mode is used while
the functional code is running, and during a call.
When Diagnostics Mode is turned on in the Admin menu, the handset
can display diagnostic screens any time it is active (in a call).
Start the display of diagnostic information by pressing the MENU key.
Pressing the MENU key multiple times will cycle through the various
screens and the normal off-hook (proxy server) display. The numeric
icon at the top of the display indicates what screen number is being
displayed. For example, the first time the MENU key is pressed, the 1
icon is shown, and the first set of counters is displayed. The next time
it is pressed, the 2 icon is shown, and the next set of counters is
displayed. The screens will be cycled through in this fashion until
there are no more screens to be displayed, after which the screen
returns to the normal off-hook proxy server screen.
Note that the normal use of the MENU key is not available if Diagnostics
Mode is enabled.
76
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Tools
The screens provided by the Diagnostics Mode include:
Screen 1
M i s s e d R c v C n t
M i s s e d X m t C n t
R x R e t r y C o u n t
T x R e t r y C o u n t
n n n n n
n n n n n
n n n n n
n n n n n
•
•
•
•
Missed receive packet count since power up (MissedRcvCnt)
Missed transmit packet count since power up (MissedXmtCnt)
Receive retry count since power up (RxRetryCount)
Transmit retry count since power up (TxRetryCount)
Screen 2
J i t t e r
n n n n n
n n n n n
m n e m o
L a s t R a t e
G a t e w y T y p e
•
Jitter is the average error or “wobble” in received packet timing,
in microseconds (jitter)
•
•
Last successful transmit data rate (LastRate)
Gateway type (not used)
Screen 3
C : m m m m
1 : m m m m
2 : m m m m
3 : m m m m
c h
c h
c h
c h
- s s
- s s
- s s
- s s
a i d
m n e m
m n e m
m n e m
PN: 1725-36034-001_B.doc
77
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Screen 3 contains a list of the APs that are heard and the following
parameters from each AP:
•
Indicator as to whether this is the current AP, or an index into the
list of other APs heard (C indicates current).
•
•
•
•
Last 2 octets of the MAC address of the AP (mmmm)
Channel number (ch)
Signal strength (ss)
Either the 802.11 Association ID (aid) from the current AP or a
mnemonic (mnem) for the reason code indicating why the handset
did not hand off to this other AP.
Where:
AP mnem: a mnemonic indicating the reason code:
•
•
•
•
•
•
•
•
•
•
•
Unkn: reason unknown
Weak: signal strength too weak
Rate: one or more basic rates not supported
Full: AP can not handle bandwidth requirements
AthT: authentication timeout
AscT: association timeout
AthF: authentication failure
AscF: association failure
SecT: security handshake timeout
SecF: security handshake failure
Cnfg: AP not configured correctly for security, QoS mode or
infrastructure network
Screen 4
A s s o c C o u n t
n n n n n
n n n n n
n n n n n
n n n n n
R e A s s o c C o u n t
A s s o c F a i l u r e
R e A s s o c F a i l
•
•
Association count since power up (AssocCount)
Re-association count since power up (ReAssocCount)
78
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Tools
•
•
Association failures since power up (AssocFailure)
Re-association failures since power up (ReAssocFail)
Screen 5
S e c - E r r C o u n t
L s t S e c E r r S e q
n n n n n
n n n n n
•
•
Security error count since power up (Sec-ErrCount)
MAC sequence number of frame with last security error
(LstSecErrSeq)
Syslog Mode
A syslog server must be present on the network in order for the
handset to send the log messages and have them saved. The syslog
server will be found with DHCP option 7 if the handset is using
DHCP. If static addresses are configured, the syslog server’s IP
address can be configured statically in the Admin menu.
If the syslog server address is blank (000.000.000.000 or
255.255.255.255), or the handset is using DHCP and no option 7 is
received from the DHCP server, the handset will not send any syslog
messages.
Admin menu options:
•
•
*Disabled turns syslog off. (default)
Errors causes the handset to log only events that are considered to
be an error (see below).
•
•
Events logs all errors plus also some other interesting events (see
below).
Full logs all the above plus a running stream of other quality
information (see below).
PN: 1725-36034-001_B.doc
79
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
The table below lists the syslog messages and which level of logging
will produce them:
Message type
Errors Events Full
Failed Handoff
Yes
No
Yes
Yes
Yes
Yes
No
Yes
Successful Handoff
Security Error
Call Start/End
Audio stats
Yes
Yes
No
Yes
Yes
No
Yes (every 5 secs)
Audio error threshold exceeded Yes
Radio stats No
Yes
No
Yes
Yes (every 5 secs)
Yes
Radio error threshold exceeded Yes
Yes
All syslog messages will include:
•
Date and time (to 1/100th of second) since handset power on
(currently set to Jan-1 00:00.00)
•
•
•
Handset’s MAC address
Handset’s IP address
Syslog sequence number
The table below lists the additional items in each message type:
Failed Handoff
Failed AP MAC
(Sent whenever the handset attempted to Failed AP signal strength
handoff, but failed trying.)
Current AP MAC
Current AP signal strength
Failure reason
Successful Handoff
New AP MAC
New AP signal strength
Old AP MAC
Old AP signal strength
Reason for handoff
Other candidate APs:
MAC
Signal strength
Reason not used
AP MAC
Security Error
AP signal strength
Security mode
Error details (mode dependent)
80
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Diagnostic Tools
Call Start
Call type (telephony, OAI, PTT)
AP MAC
AP signal strength
AP MAC
Call End
AP signal strength
AP MAC
Audio stats
AP signal strength
Payload size (in msec)
Payloads sent
Payloads received
Payloads missed (not received)
Payloads missed rate (over last 5 seconds)
Payloads late
Payloads late rate (over last 5 seconds)
Average jitter
Audio error threshold exceeded
Same as audio stats
(Sent if payloads missed rate or payloads late
rate exceeds 2%, or if the average jitter is
over 2 msec)
Radio stats
AP MAC
AP signal strength
Directed packets sent
Directed packets received
Multicast packets sent
Multicast packets received
Broadcast packets sent
Broadcast packets received
TX dropped count
TX drop rate (over last 5 seconds)
TX retry count
TX retry rate (over last 5 seconds)
RX retry count
RX retry rate (over last 5 seconds)
Same as radio stats
Radio error threshold exceeded
(Sent if TX drop rate exceeds 2% or TX or RX
retry rate exceeds 5%)
PN: 1725-36034-001_B.doc
81
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Messages are formatted like the following example:
Jan 1 00:01:26.72 0090.7a02.2a1b (172.16.0.46) [001a]
RStat: AP 00:40:96:48:1D:0C (-56 dBm), Sent 783523,
Recvd 791342, MSnt 245, MRcd 5674, BSnt 43, BRcd 10783,
TX drop 43 (0.0%), TX retry 578 (1.2%), RX retry 1217
(1.6%)
82
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Certifying the Installation
Prior to determining that an installation is complete, test the handsets
following the sequence given in Chapter 6 Testing a Handset and
conduct a Site Survey mode test according to the directions given in
Chapter 7 Diagnostic Tools.
The installation may need some adjustments. Note any areas where
coverage is conflicting or inadequate. Note any system difficulties and
work with your wireless LAN and/or LAN system administrator to
determine the cause and possible remedy. See Chapter 10
Troubleshooting for clues to possible sources of difficulties. If any
adjustments are made to the system, re-test the device in the same
vicinity to determine if the difficulty is resolved.
The installer should not leave the site before performing installation
verification.
These tests must be performed in typical operating conditions,
especially if heavy loads occur. Testing sequence and procedure is
different for every installation. Generally, you should organize the
test according to area and volume, placing numerous calls to others
who can listen while you perform coverage tests. Note any areas with
excessive static or clarity problems and report it to a Polycom service
engineer.
The coverage test will also require you to put the handset in Site Survey
mode and walk the entire coverage area to verify all APs.
Conducting a site survey
Conduct a site survey of the installation, by walking the site looking
for interfering 802.11 systems, adequate coverage and channel
assignment, and correct AP configuration.
1. Referring to Run Site Survey, put a handset into Site Survey in the
Any/Smry ESSID mode. Walk throughout the site checking for any
expected APs or other ESSIDs.
2. Then, walk the site again, in MyID/Smry ESSID mode, this time
checking that every location has adequate coverage (there should
PN: 1725-36034-001_B.doc
83
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
be at least one AP stronger than -60 dBm in all areas for 11mb/s
operation) and has good channel allocation. (At any point, the
strongest AP shown should be on a different channel than the next
best choice.)
3. Finally, use the single AP (MyID/Detl) display to check each AP, to
ensure it is configured for the proper data rates, beacon interval,
802.11 options enabled, QoS method, and security method.
Make any necessary adjustments to AP locations and configurations
and repeat steps 1 through 3 until the site survey shows adequate
coverage and correct configuration at every location.
The installation is not complete until these certification steps have
been performed. Do not hand out handsets at a site that has not been
certified.
84
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Software Maintenance
SpectraLink 8002 Wireless Telephones use proprietary software
programs written and maintained by Polycom Corporation. The
software versions that are running on the handsets can be displayed
during power on by holding down the END key.
Polycom Customer Service or an authorized dealer will provide
information about software updates and how to obtain the software
(for example, downloading from a website).
Upgrading handsets
After software updates are obtained from Polycom, they must be
transferred to the appropriate location in the LAN to update the code
used by the handsets.
SpectraLink 8002 Wireless Telephones allow over-the-air transfer of
software updates from the designated TFTP server to the handsets.
The downloader function in the handset checks its software version
every time the handset is turned on. If there is any discrepancy the
handset immediately begins to download the update.
Normal download messages
When the handset is powered on, it displays a series of messages
indicating that it is searching for new software, checking the versions,
and downloading. The normal message progression is:
Message
Description
Checking Code
Handset is contacting the TFTP server to determine if it has a newer version of
software that should be downloaded.
Erasing Memory Handset has determined that a download should occur and is erasing the current
software from memory. This message also displays a progress bar. When the
progress bar fills the display line the erase operation is complete.
PN: 1725-36034-001_B.doc
85
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Message
Description
Updating Code
Handset is downloading new software into memory. The number icons at the
bottom of the display indicate which file number is currently being downloaded. This
message also displays a progress bar. When the progress bar fills the display line
the update operation is complete on that file.
When the update is complete, the handset displays the extension
number, and is ready for use.
Download failure or recovery messages
The following display messages indicate a failure or recovery
situation during the download process.
Message
Description
Server Busy
Handset is attempting to download from a TFTP server that is busy downloading
other phones and refusing additional downloads. The handset will automatically
retry the download every few seconds.
TFTP
ERROR(x):yy
A failure has occurred during the TFTP download of one of the files. (x) = The file
number which was being downloaded; yy is an error code describing the particular
failure. Possible error codes are:
01 = TFTP server did not find the requested file.
02 = Access violation (reported from TFTP server).
07 = TFTP server reported "No such user" error. Check the TFTP server
configuration.
16 = No TFTP server address. Check the TFTP server IP configuration in the
handset or in the DHCP server.
81 = File put into memory did not pass CRC. The handset will attempt to
download the file again.
FF = Timeout error. TFTP server did not respond within a specified period of time.
Erase Failed
Waiting
Download process failed to erase the memory in the handset. This operation will
retry.
Handset has attempted some operation several times and failed, and is now waiting
for a period of time before attempting that operation again. This waiting period
preserves Battery Pack life.
86
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Troubleshooting
On occasion, you may run into transmission problems due to any
number of factors originating from the wireless LAN. SpectraLink
8002 Wireless Telephones can exhibit transmission problems in
several ways. They can cease functioning properly, display error
messages, or display incorrect data. When using and troubleshooting
handsets, consider the following problem sources to determine the
best method of approaching any specific situation. In additional to the
information in this document, you may refer to the knowledge base at
The most up-to-date support information can be found in the
Access point problems
Most, but not all, handset audio problems have to do with AP range,
positioning, and capacity. Performing a site survey as described in
this document can isolate the AP causing these types of problems. If
the handset itself is suspected, conduct a parallel site survey with a
handset that is known to be properly functioning.
In range/out-of-range
Service will be disrupted if a user moves outside the area covered by
the wireless LAN APs. Service is restored if the user moves back
within range. If a call drops because a user moves out-of-range, the
handset may be able to recover the call if the user moves back into
range within a few seconds.
Capacity
Basic WMM does not provide the capability of regulating capacity on
an AP. If capacity issues are a concern, please consult your service
representative.
PN: 1725-36034-001_B.doc
87
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Transmission obstructions
Prior to system installation, the best location for APs for optimum
transmission coverage should have been determined. However, small
pockets of obstruction may still be present, or obstructions may be
introduced into the facility after system installation. This loss of
service can be restored by moving out of the obstructed area or by
adding/rearranging APs.
Configuration problems
Certain problems are associated with improper configuration of either
the SIP system or the handset.
Configuration problems are generally corrected by changing the
configuration on the SIP system or on the handset. There may also be
incorrect programming of the AP. See the manufacturer’s instructions
for the AP in use at the site.
88
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Handset Status Messages
SpectraLink Wireless Telephone status messages provide information
about the SpectraLink 8002 Wireless Telephone’s communication with
the AP and host telephone system. The following table summarizes,
in alphabetical order, the status messages.
Message
Description
Action
Address Mismatch
Handset software download files Download new software from the
are incorrect or corrupted.
SpectraLink
website
per
Software
Maintenance.
ASSERT xxx
Line yyy
c
The handset has detected a fault Record the error code so it can be
from which it cannot recover.
reported.
Turn the handset off then on again.
If error persists, try registering a different
handset to this telephone port.
If error still persists, contact Polycom
Technical Support and report the error.
Assoc
Failed x…x
=
AP MAC address. Check handset and AP security settings.
xxxxxxxxxxxx
Handset association was refused Ensure AP is configured per Configuration
by AP; displays MAC of failing AP.
Note.
Try another AP.
Assoc
Timeout x…x AP MAC address. Check handset and AP security settings.
=
xxxxxxxxxxxx
Handset did not receive association Ensure AP is configured per Configuration
response from AP; displays MAC of Note.
failing AP.
Try another AP.
Auth
Failed x…x
=
AP MAC address. Check handset and AP security settings.
xxxxxxxxxxxx
Handset authentication was refused Ensure AP is configured per Configuration
by AP; displays MAC of failing AP.
Note.
Try another AP.
Auth
xxxxxxxxxxxx
Timeout x…x
=
AP MAC address. Check handset and AP security settings.
did not receive Ensure AP is configured per Configuration
authentication response from AP; Note.
displays MAC of failing AP. Try another AP.
Handset
Bad Code Type xx xx, yy = software license types. Check current handset license selection,
Expected
Type yy
Code Handset software does not match slnk.cfg.cfg file contents. If necessary
current handset license selection.
obtain new software per Software
Maintenance.
Bad Config
Bad ESSID
Some
needed
configuration Check all required handset configuration
parameters for valid settings.
parameter has not been set.
The handset is configured for “static Enter an ESSID in the configuration
ESSID” (as opposed to “Learn settings or change to one of the “Learn”
once” or “Learn always”), and no modes.
ESS ID has been entered.
PN: 1725-36034-001_B.doc
89
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Message
Description
Action
Bad Network IP
The value of the Network IP Enter a valid network IP address
address entered in the WT through
the menus or the configuration is
missing or invalid
Bad Network Mask The value of the Network network Enter a valid network mask
mask entered in the WT through the
menus or the configuration is
missing or invalid
Bad Phintl File
Handset software download files Download new software from the
are incorrect or corrupted.
SpectraLink
website
per
Software
Maintenance.
Bad Program File
Handset software download files Download new software from the
are incorrect or corrupted.
SpectraLink
website
per
Software
Maintenance.
(battery
Battery
beep (audio)
icon), Low battery.
Low,
In call: the battery icon displays and a soft
beep will be heard when the user is on the
handset and the battery charge is low.
User has 15–30 minutes of battery life left.
The Battery Pack can be changed while
the call is still in progress. Do not press
End Call. Place call on Hold or Park.
Quickly remove the discharged battery and
replace with a charged battery, power on
the handset, and press Start Call to
resume the call in progress.
Not in call: The battery icon displays
whenever the battery charge is low The
message Battery Low and a beep indicate
a critically low battery charge when user is
not on the handset. The handset will not
work until the Battery Pack is charged.
Battery Failure
Battery Failed
The Battery Pack is not functioning. Replace the Battery Pack with a new or
confirmed SpectraLink Battery Pack. Only
SpectraLink Battery Packs will work.
Battery Pack is damaged or Replace the Battery Pack with a new or
incompatible with handset.
confirmed SpectraLink Battery Pack. Only
SpectraLink Battery Packs will work.
Can’t Renew DHCP y…y = DHCP server IP address. Configuration problem. Check the IP
yyy.yyy.yyy.yyy
DHCP server is not responding to address configuration in the DHCP server.
initial renewal attempt.
Charging …
The handset is charging in the No action needed.
desktop charger.
Charge Complete
Checking Code
The handset is now fully charged.
No action needed.
Handset is contacting the TFTP None, this message should only last for
server to determine if it has a newer approximately one second. If message
version of software that should be remains displayed, power off and contact
downloaded.
customer support for a replacement phone.
90
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Message
Description
Action
Checking DHCP IP The handset is retrieving DHCP None. This is informational only.
information from the DHCP server.
CRC Code Error
Code Mismatch!
DCA Timeout
The software which has been TFTP Try the download again; it is possible the
downloaded has a bad redundancy software was corrupted during download. If
code check.
the error repeats, check that the download
image on the TFTP server is not corrupted.
The software loaded into the Verify the License option value is correct.
handset is incorrect for this model Replace the software image on the TFTP
handset.
server with software that is correct for the
handset model.
The handset has detected a fault Turn the handset off, then on again. If error
for which it cannot recover, possibly persists, contact Polycom Technical
due to a failure to acquire any Support and report the error.
network.
DHCP Error (1-5)
DHCP Error 1.
The handset cannot locate a DHCP server.
It will try every four seconds until a server
is located.
DHCP Error 2.
The handset has not received a response
from the server for a request to an IP
address. It will retry until a server is found.
DHCP Error 3.
DHCP Error 4.
The server refuses to lease the handset an
IP address. It will keep trying.
The server offered the handset a lease that
is too short. The minimum lease time is 10
minutes but Polycom recommends at least
one-hour minimum lease time. The
handset will stop trying. Reconfigure the
server and power cycle the handset.
DHCP Error 5.
Failure during WEP Key rotation process
(proprietary feature).
DHCP Lease Exp y…y = DHCP server IP address.
The handset failed to renew its DHCP
lease, either because the DHCP server is
not running, or because the configuration
has been changed by the administrator.
The handset will attempt to negotiate a
new lease, which will either work, or it will
change to one of the above DHCP errors
(1 through 4).
yyy.yyy.yyy.yyy
DHCP is not responding to renewal
attempts .
DHCP NACK error y…y = DHCP server IP address. The DHCP lease currently in use by the
yyy.yyy.yyy.yyy
DHCP server explicitly refused handset is no longer valid, which forces the
renewal.
handset to restart. This problem should
resolve itself on the restart. If it does not,
the problem is in the DHCP server.
DL Not On Sector
Handset software download files Obtain new software per Software
are incorrect or corrupted.
Maintenance.
PN: 1725-36034-001_B.doc
91
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Message
Description
Action
DO NOT POWER The handset is in a critical section None. Do not remove the Battery Pack or
OFF
of the software update.
attempt to power off the phone while this is
displayed. Doing so may render the
handset inoperable.
Duplicate IP
The handset has detected another If using DHCP, check that the DHCP
device with its same IP address.
server is properly configured to avoid
duplicate addresses.
If using Static IP, check that the handset
was assigned a unique address.
Erase Failed
Download process failed to erase Operation will retry but may eventually
the memory in the handset.
report the error "int. error: 0F" Power cycle
the handset.
Erasing Memory
Handset has determined that a None. When the progress bar fills the
download should occur and is display line the erase operation is
erasing the current software from complete.
memory.
Do not remove the Battery Pack or attempt
to turn the handset off during this
operation.
Files Too Big
Handset software download files Download new software per Software
are incorrect or corrupted.
Maintenance.
Flash Config Error
Handset internal configuration is Perform "Restore Defaults" operation via
corrupt.
administrator menus (or re-program with
Configuration Cradle).
Initializing …
The handset is performing power- None. This is informational only.
on initialization.
Internal Err. # #
The handset has detected a fault Record the error code so it can be
from which it cannot recover.
reported.
Turn the handset off then on again.
If error persists, try registering a different
handset
to
this
telephone
port.
If error still persists, contact Polycom
Technical Support and report the error.
Must Upgrade SW!
No DHCP Server
Handset software is incompatible Download new software from the
with hardware.
SpectraLink
website
per
Software
Maintenance.
Handset is unable to contact the Check that your DHCP server is
DHCP server.
operational and connected to WLAN or use
Static IP configuration in the handset.
No ESSID
Attempted to run Site Survey Statically configure an ESSID in the Admin
application without an ESSID set. menu.
No Func Code
Handset software is incorrect or Reconfigure the handset to gain access to
corrupted.
the WLAN and download new handset
software.
92
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Message
Description
Action
No Host IP (Addr)
The handset is configured for “static Enter
a
valid IP address in the
IP” (as opposed to “use DHCP”) configuration settings or change to “use
and no valid host IP address (the DHCP.”
handset’s IP address) has been
entered.
No IP Address
No Net Access
Invalid handset IP address.
Check the IP address of the handset and
reconfigure if required, or change to “use
DHCP”.
Cannot communicate with LAN Verify the AP connectivity to the LAN.
devices through the WLAN (such
as PBX).
Verify that all the WEP settings in the
handset match those in the APs.
No Net
No APs
Found Handset cannot find any APs
This indicates any of the following:
No radio link.
Verify that the AP is turned on. Verify
WMM is enabled on AP. WMM is
mandatory.
No
ESSID:
Auto-learn
not Verify the ESSID of the wireless LAN and
enter or Auto learn it again if required.
supported (or) incorrect ESSID.
AP does not support appropriate Check the AP configuration.
data rates.
Out of range.
Try getting closer to an AP. Check to see
if other handsets are working within the
same range of an AP. If so, check the
ESSID of this handset.
Incorrect Security settings.
Verify that all the Security settings in the
handset match those in the APs.
No
Net
Found x…x
yy
Handset cannot find a suitable AP; Tx
displays MAC and signal strength Ensure APs are configured correctly.
of “best” non-suitable AP found. Try Site Survey mode to determine a more
=
AP MAC address. Check AP and handset network settings
AP signal strength. such as ESSID, Security, Reg domain and
power.
xxxxxxxxxxxx yy
=
specific
cause.
Enable WMM in the APs.
No PBX Response
The handset has exceeded its Verify that proxy server IP address and
retransmission limit with no ACK port are properly configured.
response from proxy server.
No Reg Domain
No SIP DHCP
No SW Found
Regulatory Domain not set.
Configure the Regulatory Domain in the
handset.
DHCP is configured but no valid Check DHCP server configuration for
SIP option 43 was found. option 43 and reconfigure if required.
A required software component has Check that the handset license type
not been identified.
(number) has a corresponding entry in the
slnk_cfg.cfg file.
Check that the pd11wsd.bin and
pi110001.bin entries exist in under this
license type in the slnk_cfg.cfg file.
PN: 1725-36034-001_B.doc
93
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
Message
Description
Action
Not Installed!
A required software component is Check that all required software files are
missing.
on the TFTP server, if over-the-air
downloading is being used. If the error
repeats, contact Polycom Technical
Support.
Press End Call
Select License
The far end of a call has hung up.
Hang up the near end by pressing the END
key.
A protocol has not been selected Using the Admin menu, select one license
from the license option setting.
option to allow the phone to download the
appropriate software.
Server Busy
Handset is attempting to download None, the handset will automatically retry
from a TFTP server that is busy the download every few seconds.
downloading other devices and
refusing additional downloads.
Storing Config
Handset is storing changes to None. Informational only. The handset may
handset configuration.
display this briefly following a configuration
change or software download.
TFTP ERROR(x):yy A failure has occurred during a Error code 01, 02, 07, or 16 - check the
TFTP software download. (x) = The TFTP server configuration.
file number which was being
downloaded; yy is an error code
Error code 81, the handset will attempt to
download the file again.
describing the particular failure.
For other messages, power off the
Possible error codes are:
handset, then turn it on again to retry the
download. If the error repeats, note it and
contact Polycom Customer Support.
01 = TFTP server did not find the
requested file.
02 = Access violation (reported
from TFTP server).
07 = TFTP server reported "No
such user" error.
16 = No TFTP server address.
81 = File put into memory did not
CRC.
FF = Timeout error. TFTP server
did not respond within a specified
period of time.
Too Many Errors
The handset continues to reset and Fatal error. Return handset to Polycom.
cannot be recovered.
Unknown
xx:yy:zz
A phrase is missing from the Obtain new software per Software
language file.
Maintenance.
Unsupported Codec The proxy server has requested Check proxy server configuration for
using a codec not supported by the supported codecs and reconfigure if
handset.
necessary.
Updating …
The handset is updating its None. The handset may do this briefly after
software .
a download. This is informational only.
94
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Message
Description
Action
Updating Code…
Handset is downloading new None. When the progress bar fills the
software into memory. The number display line the update operation is
icons at the bottom of the display complete on that file.
indicate which file number is
currently being downloaded. This
message also displays a progress
bar. When the progress bar fills the
display line the update operation is
complete on that file.
Do not remove the Battery Pack or attempt
to turn the handset off during this
operation.
Waiting…
Handset has attempted some None. The handset is waiting for a
operation several times and failed.
specified period of time before attempting
that operation again.
Wrong Code Type
The software loaded into the Replace the software image on the TFTP
handset is incorrect for this model server with software that is correct for the
phone.
handset model and restart the handset.
PN: 1725-36034-001_B.doc
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Regulatory Domains
This table details the specifications for regulatory domain settings.
Polycom recommends that you check with local authorities for the
latest status of their national regulations for 2.4 GHz wireless LANs.
Domain
Identifier
Max. Power Limit
(peak power)
Band
Channels
Countries
01
2.4000 – 2.4745 MHz
1-11
100mW (+20dBm)
Argentina
Canada
Mexico
Taiwan
US
02
2.4000 – 2.4845 MHz
1-13
100mW (+20dBm)
Australia
Europe
Hong Kong
Japan
New Zealand
Singapore
03
04
(reserved)
Spain
2.4445 – 2.4745 MHz
2.4145 – 2.4845 MHz
2.4000 – 2.4845 MHz
10-11
10-13
1-13
30mW (+15dBm)
30mW (+15dBm)
30mW (+15dBm)
05
06
France
Korea
PN: 1725-36034-001_B.doc
97
Download from Www.Somanuals.com. All Manuals Search And Download.
SpectraLink 8002 Wireless Telephones Configuration and Administration (SIP)
98
PN: 1725-36034-001_B.doc
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
OAI Server IP ...............................................27, 29
Obstructions ..........................................................88
Out of range...........................................................87
A
Access point
Coverage.............................................................76
Coverage test ......................................................83
Access point, description.....................................15
Automatic Learn...................................................30
P
Preferences, user-defined ....................................34
R
C
Regulatory Domain ..............................................32
Restore Defaults....................................................33
Capacity .................................................................87
Checking code.......................................................85
Customer Support Hotline....................................6
S
Site Certification....................................................83
Status messages.....................................................89
D
Download messages
Failure or Recover ..............................................86
Normal................................................................85
T
Transmission obstructions...................................88
E
U
Erasing memory....................................................85
Ethernet Switch, description ...............................16
Updating code.......................................................85
User Preferences....................................................34
H
W
Hotline......................................................................6
Wireless Telephone
Configuration problems ......................................88
Description..........................................................15
Display IP address of..........................................39
Problems with .....................................................87
Status messages ..................................................89
O
OAI
OAI Gateway......................................................27
OAI On/Off.........................................................27
PN: 1725-36034-001_B.doc
99
Download from Www.Somanuals.com. All Manuals Search And Download.
|