2015 600 / 800 RUSH
2015 600 / 800 SWITCHBACK
Snowmobile Owner's Manual
for Maintenance and Safety
Download from Www.Somanuals.com. All Manuals Search And Download.
WELCOME
Thank you for purchasing a POLARIS vehicle, and welcome to our
world-wide family of POLARIS enthusiasts. Be sure to visit us online at
www.polaris.com for the latest news, new product introductions,
upcoming events, career opportunities and more.
Here at POLARIS we proudly produce an exciting line of utility and
recreational products.
• Snowmobiles
• All-terrain vehicles (ATVs)
• Low emission vehicles (LEVs)
• RANGER® utility vehicles
• RZR® sport vehicles
• VICTORY® motorcycles
• GEM® vehicles
We believe POLARIS sets a standard of excellence for all utility and
recreational vehicles manufactured in the world today. Many years of
experience have gone into the engineering, design, and development of
your POLARIS vehicle, making it the finest machine we've ever
produced.
For safe and enjoyable operation of your vehicle, be sure to follow the
instructions and recommendations in this owner's manual. Your manual
contains instructions for minor maintenance, but information about
major repairs is outlined in the POLARIS Service Manual and should be
performed only by a factory certified Master Service Dealer® (MSD)
technician.
Your POLARIS dealer knows your vehicle best and is interested in your
total satisfaction. Be sure to return to your dealership for all of your
service needs during, and after, the warranty period.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
The following are trademarks of POLARIS Industries Inc.:
POLARIS®
PERC®
AXYS™
RUSH®
SWITCHBACK®
SWITCHBACK ADVENTURE®
LOCK & RIDE®
Copyright 2014 POLARIS Industries Inc. All information contained within this
publication is based on the latest product information at the time of publication. Due to
constant improvements in the design and quality of production components, some minor
discrepancies may result between the actual vehicle and the information presented in
this publication. Depictions and/or procedures in this publication are intended for
reference use only. No liability can be accepted for omissions or inaccuracies. Any
reprinting or reuse of the depictions and/or procedures contained within, whether whole
or in part, is expressly prohibited.
The original instructions for this vehicle are in English. Other languages are provided as
translations of the original instructions.
Printed in U.S.A.
2015 600/800 AXYS Snowmobile Owner’s Manual
P/N 9925073
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
This section contains helpful information for owners and drivers and
illustrates the location of important identification numbers that should
be recorded in the owner's manual.
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
This section describes safe vehicle operation and identifies warning
labels and their locations.
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
This section identifies the locations of your snowmobile's controls and
features.
The Perfect Fit . . . . . . . . . . . . . . . . . . . . . . . . . 51
This section includes a Suspension Quick Set-Up Guide and explains
how to make additional suspension adjustments for the perfect riding
experience.
Pre-Ride Inspections . . . . . . . . . . . . . . . . . . . . 66
This section explains procedures that must be performed before riding.
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
This section explains proper engine break-in, operation of features and
general operating procedures.
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
This section defines your role, and your dealer's role, in your
snowmobile's regular maintenance.
POLARIS Products. . . . . . . . . . . . . . . . . . . . . 137
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . 138
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 158
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Maintenance Log . . . . . . . . . . . . . . . . . . . . . . 171
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Important Notes for Owners and Drivers
After reading this manual, store it in the snowmobile for convenient
reference. It should remain with the snowmobile when the snowmobile
is sold.
Some of the illustrations and photos used in this manual are general
representations. Your model may differ.
Follow the maintenance program outlined in this manual. Preventive
maintenance ensures that critical components of the snowmobile are
inspected by your dealer at specific mileage intervals.
You and your dealer must complete the registration form included with
your snowmobile and forward it to us. This completed form is necessary
to ensure warranty coverage.
Protect and preserve your right to ride by joining your local trail riding
clubs.
When teaching inexperienced operators to ride, set up a predetermined
course for practice. Make sure they know how to drive and control the
snowmobile before allowing them to make longer trips. Teach them
proper snowmobile courtesy, and enroll them in driver’s training and
safety courses sponsored by local or state organizations.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Preservation of the Environment
POLARIS is committed to supporting an environmental education
campaign. We encourage state and provincial governments across the
snowbelt to adopt rigorous safety training programs that encourage
protection of our environment, including wildlife and vegetation.
Snowmobile clubs and other organizations are working together to
protect our environment. Please support their efforts and operate your
snowmobile with consideration for the protection and preservation of
our environment.
Noise Level
One of the most publicized issues about snowmobiles is noise. The
Society of Automotive Engineers (SAE), the standard-setting body for
snowmobile development, recommends that snowmobiles conform to
prescribed sound levels.
POLARIS snowmobiles are engineered to conform to these SAE
standards. Our muffler systems are designed to reduce noise levels and
must not be altered or removed. The sound of your snowmobile may not
be welcome to non-snowmobilers, so you have a responsibility to
operate your snowmobile with concern for others. We do our part by
manufacturing quieter machines; we ask your help to further reduce the
impact of noise by operating your snowmobile safely and responsibly.
Air Pollution
POLARIS engineers continuously investigate ways to reduce emission
levels of two-stroke engines. We expect our efforts to lead to the
reduction of potential air pollution.
In addition to our technological research, we encourage government
agencies, manufacturers, distributors, dealers, ecologists, and other
interested parties to work together to develop data on environmental
topics.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Vehicle Identification Numbers
Record your snowmobile's identification numbers and key number in
the spaces provided.
NOTE: The Vehicle Identification Number (VIN) is stamped into the side of the
tunnel and printed on the tunnel VIN label.
Certification Label
Emissions Certification Label
Tunnel VIN
Vehicle Model Number: ___________________________________________________
Tunnel VIN (right side of tunnel): ____________________________________________
Engine Serial Number (on recoil housing): _____________________________________
Key Number: ____________________________________________________________
NOTICE: If installing an aftermarket tunnel wrap, do not cover the tunnel
certification, tunnel VIN or emissions certification labels with the wrap.
If the tunnel wrap doesn’t provide an opening for these labels, remove
the section of wrap where the labels are located.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Engine Serial Number
The engine serial number is located
on the identification label on the
engine recoil cover.
Key Identification
Engine Serial Number
The ignition keys are etched with an
identification number. Remove the
spare key and store it in a safe place.
Your key can be duplicated only by
mating a POLARIS key blank using
the same identification number with
one of your existing keys, so if both
keys are lost, the ignition switch
assembly must be replaced.
Key Identification
Number
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
The following signal words and symbols appear throughout this manual
and on your vehicle. Your safety is involved when these words and
symbols are used. Become familiar with their meanings before reading
the manual.
The safety alert symbol indicates a potential personal injury hazard.
DANGER
A DANGER indicates a hazardous situation that, if not avoided, will result in
death or serious injury.
WARNING
A WARNING indicates a hazardous situation that, if not avoided, could result in
death or serious injury.
CAUTION
A CAUTION indicates a hazardous situation that, if not avoided, could result in
minor or moderate injury.
NOTICE
A NOTICE indicates a situation that could result in property damage.
The Prohibition Safety Sign indicates an action NOT to take in order
to avoid a hazard.
The Mandatory Action Sign indicates an action that NEEDS to be
taken to avoid a hazard.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Follow the recommended maintenance program beginning on page 88
of this manual to ensure that all critical components on the snowmobile
are thoroughly inspected by your dealer at specific mileage intervals.
WARNING
Driving a snowmobile requires your full attention. DO NOT drink alcohol or use
drugs or medications before or while driving or riding as a passenger. They will
reduce your alertness and slow your reaction time.
Snowmobiles are capable of traveling at high speeds. Use extra caution to
ensure operator safety. Make sure your snowmobile is in excellent operating
condition at all times. Always check major and vital safety components before
every ride.
All POLARIS snowmobiles are designed and tested to provide safe operation
when used as directed. Failure of critical machine components may result from
operation with any modifications, especially those that increase speed or power.
DO NOT MODIFY YOUR MACHINE. The snowmobile may become aerody-
namically unstable at speeds higher than those for which it is designed. Loss of
control may occur at higher speeds. Modifications may also create a safety haz-
ard and lead to bodily injury.
The warranty on your entire machine is terminated if any equipment has been
added, or any modifications have been made, to increase the speed or power of
the snowmobile.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Stay Clear of Track
Your snowmobile is propelled by a revolving track that must be partially
exposed for proper operation. Do not stand on the plastic flap.
WARNING! Serious injuries may result if
NO
STEP
hands, feet, or clothing become entangled
in the track. Be alert when riding, and
remain properly seated to stay clear of the
track. Never hold the snowmobile up or
stand behind it while warming up the track.
A loose track or flying debris could cause
serious injury or death. We recommend
having your dealer perform all track service
and alignment procedures.
Stay Clear of Engine
Never attempt adjustments with the engine running. Stop the engine
before opening a side panel. Always ensure that the hood and side
panels are installed and securely latched before starting the engine.
WARNING! Serious injury can occur if fingers or clothing contact the moving
parts of an engine. Always stop the engine before attempting adjustments.
Riding Position
Operating a snowmobile requires skill and balance for proper control.
Rider positions may vary with experience and the features available on
some snowmobiles, but under many conditions, the proper position is to
be seated with both feet on the running boards and both hands on the
handlebar grips for proper throttle, brake and steering control.
WARNING! Improper riding position may reduce control and could result in
serious injury or death. Always ride in a position that allows for control of your
vehicle.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Riding Apparel
Helmet
Wearing a helmet can prevent a severe head injury. Whenever riding a
POLARIS vehicle, always wear a helmet that meets or exceeds
established safety standards.
Approved helmets in the USA and Canada bear a U.S. Department of
Transportation (DOT) label.
Approved helmets in Europe, Asia and Oceania
bear the ECE 22.05 label. The ECE mark consists
4
E
of a circle surrounding the letter E, followed by the
distinguishing number of the country which has
granted approval. The approval number and serial
number will also be displayed on the label.
051039
0006.31
Eye Protection
Do not depend on eyeglasses or sunglasses for eye protection.
Whenever riding a POLARIS vehicle, always wear shatterproof goggles
or use a shatterproof helmet face shield. POLARIS recommends
wearing approved Personal Protective Equipment (PPE) bearing
markings such as VESC 8, V-8, Z87.1, or CE. Make sure protective eye
wear is kept clean.
Clothing
Be prepared, be warm and be
comfortable when riding. Be aware of
the weather forecast, especially the
windchill, and dress accordingly. See
the chart on page 21.
WARNING! Avoid wearing loose clothing
or long scarves, which can become
entangled in moving parts and cause
serious injury. Always wear an approved
helmet and eye protection.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Disabled Operators
Safe operation of this rider-active vehicle requires good judgement and
physical skills. Operators with cognitive or physical disabilities have an
increased risk of loss of control, which could result in serious injury or
death.
Survival Preparation
For your safety, always ride in a group of other snowmobilers. Always
tell someone where you're going and how long you expect to be gone. If
it isn't possible to ride with others, and you must travel into remote
areas, always carry survival equipment that's appropriate to the
conditions you may encounter. Such equipment may include, but is not
limited to: extra clothing, a sleeping bag, a flashlight, food and water, a
signaling mirror, a means of building a fire and a two-way radio or
cellular telephone.
Always carry the owner’s manual on your snowmobile. For added
protection, purchase and carry the following items on your snowmobile
as well:
• Spare Drive Belt
• Extra Set of Spark Plugs
• Tow Rope
• Winter Survival Kit
• Trail Map
• First Aid Kit
• Tool Kit
• Extra Oil
• Fuel Deicer
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Rider Capacity
This snowmobile is designed for a single rider only. Never carry a
passenger on this snowmobile.
Excessive Speed
WARNING! High speed driving, especially at night, could result in serious injury
or death. Always reduce speed when driving at night or in inclement weather.
Always observe all state and local laws governing snowmobile
operation and speed limits. Always be alert and pay attention to the trail
ahead. If your speed is 40 MPH (64 km/h), your snowmobile is traveling
about 60 feet (18 m) per second. If you look back for only two seconds,
your snowmobile will travel about 120 feet (36 m). If your speed is 60
MPH (96 km/h), your snowmobile will travel about 180 feet (55 m) in
two seconds.
Traveling at night requires extra caution. Check headlight and taillight
to ensure proper operation, and don’t over-drive your headlight beam.
Always be able to bring your snowmobile to a stop in the distance
illuminated by the headlight.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Driver Awareness
Slow down when traveling near poles, posts, or other obstacles. Be
especially alert if you're snowmobiling after dark. Always be on the
alert for wire fences. Single strands are especially dangerous, since there
may be a great distance between posts. Guy wires on utility poles are
also difficult to distinguish.
Make sure the way is clear before crossing
railroads and other roads and highways. The
noise of your snowmobile will drown out the
sound of approaching vehicles. Look ahead,
behind, and to both sides before turning or
crossing railroad tracks or highways. Steep
embankments may also hide your view.
Always leave yourself a way out.
R R
Variances in snow depth and/or water currents may result in uneven ice
thickness. You may drown if you break through the ice. Never travel on
frozen bodies of water unless you have first verified that the ice is
sufficiently thick to support the weight and moving force of the
snowmobile, you and your cargo, together with any other vehicles in
your party. Always check with local authorities and residents to confirm
ice conditions and thickness over your entire route. Snowmobile
operators assume all risk associated with ice conditions on frozen bodies
of water.
When teaching inexperienced operators to ride, set up a predetermined
course for practice. Make sure they know how to drive and control the
snowmobile before allowing them to make longer trips. Teach them
proper snowmobile courtesy, and enroll them in driver's training and
safety courses.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Avalanches
Snowmobilers should always be properly
trained and equipped before traveling in
mountainous terrain:
• Take an avalanche class
• Travel with experienced people
• Travel on designated trails
• Make sure each person is equipped
with a shovel, probe and avalanche
beacon.
You don’t have to be snowmobiling on a slope for an avalanche to occur.
Be aware that all of the snow is connected. You may be riding on a flat
slope or snow covered road, but if the snowpack above is unstable
enough you can trigger an avalanche on a steeper slope above you.
Always be aware of snow conditions above you as you travel in
mountainous terrain.
Before riding in mountainous terrain, call or log on to your local
avalanche advisory to get current weather and snow stability
information.
For more information about avalanche training and avalanche
conditions, contact local law enforcement in your area, or visit the
American and Canadian online avalanche centers at
www.avalanche.org.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Ice and Snow Build-up
WARNING! Ice and snow build-up may interfere with the steering of your
snowmobile, resulting in serious injury or death. Keep the underhood area free
of snow and ice.
Before driving, manually turn the skis to the left and right to be sure ice
and snow are not interfering with full left and right steering. If difficulty
is encountered, remove ice and snow build-up that may be obstructing
the steering linkage.
Driving on Slippery Surfaces
WARNING! Never attempt an abrupt change of direction when operating on
slippery surfaces. Proceed slowly and use extra caution. Driving on ice or hard-
packed snow reduces steering and braking control, which may result in loss of
control and serious injury or death. Slow down and use extra caution when
operating on slippery surfaces.
Inadequate Snow Conditions
Since snow provides the only lubrication for the power slide suspension
and, on liquid cooled models, cooling for the engine, adequate snow
cover is a requirement for operation of your snowmobile.
NOTICE: Driving in too little snow will result in excessive wear and damage to
the slide rail, track and/or engine.
WARNING! Inadequate cooling and lubrication will lead to overheating of the
slide rail and track, causing premature wear, damage and failure, which can
result in serious injury. Reduce speeds and frequently drive into fresh snow to
allow adequate cooling and polishing of the slide rail and track surfaces. Avoid
operating for prolonged periods on ice, hard-packed surfaces or roads.
Operating in Deep Snow
If the snowmobile becomes stuck in snow, clear the running board area
of snow, then step down the snow in front of the snowmobile so that
when the throttle is opened, the snowmobile will be able to climb up and
over the snow.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Driving Downhill
When riding downhill, shift your weight to the rear of the snowmobile
and reduce your speed to a minimum. Apply just enough throttle to keep
the clutch engaged, allowing the engine's compression to help slow the
snowmobile and keep it from rolling freely downhill.
WARNING! When driving on long downhill stretches, pump the brakes. Riding
the brakes may cause the brake system to overheat, which may result in brake
failure. Excessive or repetitive use of the brakes for high speed stops will also
cause an overheated brake system. This condition may lead to a sudden loss of
brakes and/or fire and may result in serious injury or death.
Driving in Hilly Terrain
WARNING! Climbing a hill or crossing the face of a slope may result in loss of
balance and snowmobile rollover, causing serious injury or death. Use caution
and good judgement when driving in hilly terrain.
Use extra caution when operating in hilly terrain. If climbing a hill is
unavoidable, keep your weight low and forward. If you must cross the
face of a slope, keep your weight on the uphill side of the snowmobile to
maintain proper balance and avoid possible roll-over.
Slow down when reaching the crest of a hill. Be prepared to react to
obstacles, sharp drops or other people or vehicles that may be on the
other side of the hill.
If you’re unable to continue up a hill, turn the snowmobile downhill
before it loses momentum. If this isn't possible, spin the track just
enough to dig in to prevent it from rolling back down the hill. Stop the
engine and set the parking brake (if equipped). Keeping away from the
downhill side of the snowmobile, pull the rear of the snowmobile
around and point the front end and skis downhill. Remount the
snowmobile, restart the engine, release the parking brake, and descend
the hill carefully.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Drive Belt
Do not operate the engine with the drive belt removed.
Any servicing that requires operation without a belt must be performed
by your dealer.
NOTICE: Operation of the engine with the belt removed may result in injury or
damage to the engine.
Intake Silencer
Do not operate the engine with the intake silencer or filter removed.
NOTICE: Damage to the engine may occur if the intake silencer or filter are
removed.
Clutches
Do not attempt to service the clutches.
All clutch service must be performed by your dealer. The clutch is a
complex mechanism that rotates at high speeds. Each clutch is
dynamically balanced before installation. Any tampering may disrupt
this precision balancing and create an unstable condition.
Cold Weather Drive-Away
Whenever your snowmobile has been parked for a length of time,
especially overnight, always make sure the skis and track are loosened
from ice and snow before attempting to drive. Apply the throttle with
enough authority to put the snowmobile into motion, but always operate
within safety limits.
Maneuverability
While much control and maneuverability is achieved through the
steering system and skis, maximum control is achieved by the shifting
of your body weight. Maneuverability will change for lighter operators
or snowmobiles designed to carry a load.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Driving Responsibly
Every snowmobile handles differently, and even the most docile
conditions may become dangerous if operators drive improperly. If
you're new to snowmobiling, acquaint yourself with the snowmobile
and with what it will and won't do under various conditions. Even
seasoned drivers should spend some time getting the feel for a
snowmobile before attempting ambitious maneuvers.
• A snowmobile depends on the rider’s body position for proper
balance in executing turns, traversing hills, etc. Always start on a
smooth, level area to begin building your operating experience.
• Before allowing someone else to use your snowmobile, know the
extent of their operating skills. Check to see if they've taken a
snowmobile safety course and have an operator's certificate. For their
protection, as well as yours, make sure they take a snowmobile safety
course. Everyone can benefit from the course.
• Don't “jump” your snowmobile over large drifts or similar terrain.
Jumping may injure your back because of spinal compression that
could occur when the snowmobile impacts the ground. The seat and
suspension of your snowmobile have been designed to provide
protection under normal riding conditions. Your snowmobile is not
intended for this kind of use.
• Be courteous to oncoming traffic by dimming your headlights and
reducing your speed.
• When traveling in a group of snowmobiles, don't tailgate (follow too
closely). Leave enough distance between snowmobiles to provide
ample stopping room and to provide protection from flying snow and
debris. Allow even more distance when driving on slippery surfaces
or when driving in darkness or other low visibility conditions. Be
aware of any snowmobile traffic around your vehicle. Drive
defensively to avoid accidents.
• Remove the key from the ignition when you leave the snowmobile
unattended.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Operator Safety
Windchill/Temperature Charts
The following information is provided to help you determine when
temperatures become dangerous for riding.
WINDCHILL CHART (°F)
Wind
Speed
in
Actual Thermometer Reading (°F)
-5 -10 -15 -20 -25 -30 -35 -40 -45
Equivalent Temperature (°F)
-5 -10 -15 -20 -25 -30 -35 -40 -45
-5 -11 -16 -22 -28 -34 -40 -46 -52 -57 -63
40 35 30 25 20 15 10
5
0
MPH
Calm 40 35 30 25 20 15 10
5
0
5
36 31 25 19 13
7
3
0
1
10
15
20
25
30
35
40
45
50
55
60
34 27 21 15
32 25 19 13
30 24 17 11
9
6
4
3
1
0
-4 -10 -16 -22 -28 -35 -41 -47 -53 -59 -66 -72
-7 -13 -19 -26 -32 -39 -45 -51 -58 -64 -71 -77
-2 -9 -15 -22 -29 -35 -42 -48 -55 -61 -68 -74 -81
-4 -11 -17 -24 -31 -37 -44 -51 -58 -64 -71 -78 -84
-5 -12 -19 -26 -33 -39 -46 -53 -60 -67 -73 -80 -87
-7 -14 -21 -27 -34 -41 -48 -55 -62 -69 -76 -82 -89
29 23 16
28 22 15
28 21 14
27 20 13
26 19 12
26 19 12
25 18 11
25 17 10
9
8
7
6
5
4
4
3
-1 -8 -15 -22 -29 -36 -43 -50 -57 -64 -71 -78 -84 -91
-2 -9 -16 -23 -30 -37 -44 -51 -58 -65 -72 -79 -86 -93
-3 -10 -17 -24 -31 -38 -45 -52 -60 -67 -74 -81 -88 -95
-3 -11 -18 -25 -32 -39 -46 -54 -61 -68 -75 -82 -89 -97
-4 -11 -19 -26 -33 -40 -48 -55 -62 -69 -76 -84 -91 -98
Frostbite in >> 30 min. 10 min. 5 min.
WINDCHILL CHART (°C)
Wind
Speed
in
Actual Thermometer Reading (°C)
5
2
-1 -4 -7 -10 -13 -16 -19 -22 -25 -28 -31 -34 -37 -40 -43 -46
Equivalent Temperature (°C)
Km/h
Calm
8
5
3
2
1
0
2
0
-1 -4 -7 -10 -13 -16 -19 -22 -25 -28 -31 -34 -37 -40 -43 -46
-4 -7 -11 -14 -18 -22 -25 -29 -32 -36 -39 -43 -46 -50 -53 -57
16
24
32
40
48
56
64
72
80
88
96
-2 -6 -10 -13 -17 -21 -24 -28 -32 -36 -39 -43 -47 -50 -54 -58 -62
-3 -7 -11 -15 -19 -22 -26 -30 -34 -38 -42 -45 -49 -53 -57 -61 -65
-4 -8 -12 -16 -20 -24 -28 -32 -36 -39 -43 -47 -51 -55 -59 -63 -67
-1 -5 -9 -13 -17 -21 -25 -29 -33 -37 -41 -45 -49 -53 -57 -61 -65 -69
-1 -5 -9 -13 -18 -22 -26 -30 -34 -38 -42 -46 -50 -54 -58 -62 -66 -70
-2 -6 -10 -14 -18 -22 -26 -31 -35 -39 -43 -47 -51 -55 -59 -64 -68 -72
-2 -6 -10 -15 -19 -23 -27 -31 -35 -40 -44 -48 -52 -56 -61 -65 -69 -73
-2 -7 -11 -15 -19 -23 -28 -32 -36 -40 -45 -49 -53 -57 -61 -66 -70 -74
-3 -7 -11 -15 -20 -24 -28 -33 -37 -41 -45 -50 -54 -58 -62 -67 -71 -75
-3 -7 -12 -16 -20 -24 -29 -33 -37 -42 -46 -50 -55 -59 -63 -67 -72 -76
-3 -8 -12 -16 -21 -25 -29 -34 -38 -42 -47 -51 -55 -60 -64 -68 -73 -77
Frostbite in >> 30 min. 10 min. 5 min.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Safety Labels and Locations
Warning labels have been placed on the snowmobile for your protection.
Read and follow the instructions of the labels and other warnings on the
snowmobile carefully. If any of the labels depicted in this manual differ
from the labels on your snowmobile, always read and follow the
instructions of the labels on the snowmobile.
If any label becomes illegible or comes off, contact your POLARIS
dealer to purchase a replacement. Replacement safety labels are
provided by POLARIS at no charge. The part number is printed on the
label.
Pressure Cap Warning
Pressure Cap
Warning
This warning label is found on the
pressure cap of applicable liquid
cooled models:
WARNING
Do not open hot. Test or replace
when changing coolant. Press
down and turn to release cap.
13 PSI
7170063
Track Warning
Track Warning
WARNING
Stay clear of track. Do not sit on
seat back. Entanglement with
the track or a fall from seat back
may result in severe injury or
death.
7175974
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Safety Labels and Locations
No Passenger Warning
Fuel Recommendation Label
WARNING
No Passenger
Warning
This vehicle is designed for
operator only. NO
PASSENGER.
7181012
Fuel Recommendation
Label
91+ Octane without Ethanol.
For maximum performance see
decal on left hand side panel
for setting.
7181061
Reverse Warning
Reverse Warning
WARNING
Reverse operation, even at low speeds, can cause loss of control
resulting in serious injury or death. To avoid loss of control,
always:
• Look behind before and while backing up.
• Avoid sharp turns.
• Shift to or from reverse only when stopped.
• Apply throttle slowly.
NOTE: For more information, see Owner’s Manual.
If electric reverse:
• Machine stopped and engine at idle, push yellow button on LH
control to reverse. Flashing light on dash indicates reverse
operation.
• Push button again to return to forward.
7176779
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Safety Labels and Locations
Operation Warning
WARNING
• To avoid serious injury or death,
read and understand all warnings
and the Owner's Manual before
operation. If manual is missing,
contact a POLARIS dealer for a
replacement.
• This vehicle is capable of high
speeds. Buried objects or uneven
terrain can cause loss of control.
Reduce speed and use extreme
caution when operating in
Operation Warning
unfamiliar terrain.
• Excessive speed, especially at night or with limited visibility, can result
in insufficient time for you to react to terrain changes, to avoid
unexpected obstacles, or to stop safely.
• Never consume alcohol or drugs before or while operating this vehicle.
• In an emergency, push down the Auxiliary Shut-Off Switch, located on
the top of the throttle control assembly, to stop the engine. Then pull the
brake lever to stop.
• Always wear an approved helmet, eye protection, and adequate clothing
while operating this vehicle.
• This vehicle is designed for adult use only. Check local laws for age
requirements.
• When operating with a passenger (on approved models only) reduce
speed and allow extra space for steering and stopping. A passenger
reduces your ability to control the vehicle.
• When operating on hard-packed snow, ice, or when crossing roads,
steering and braking ability are greatly reduced. Reduce speed and
allow extra space to turn or stop.
• To maintain vehicle control on ice or hard-packed surfaces, you should
have a proper balance of ski carbides to track studs. See Owner's
Manual for proper use of traction products.
• Repeated stops from high speed may cause fading or sudden loss of
braking ability.
• Parking brake may relax when used for long periods. Do not leave brake
engaged for more than five minutes.
• Before starting engine, check throttle, brake, and steering for proper
operation. Make sure hood and side panels are latched. Be seated and
in position to control the vehicle.
Oil injection system: Use unmixed fuel only. Check oil level when
refueling.
7176779
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Safety Labels and Locations
Clutch Warning/Belt Removal
WARNING
Do not operate engine with hood or side panels open. Do not attempt
adjustment with engine running. Do not operate engine with the clutch
guard removed. Never run engine with drive belt removed. Never service
clutches yourself - See your dealer.
Belt Removal - All Units
Clutch Warning/Belt Removal
1. For electric reverse models,
engine must be stopped in
forward to allow clutch
opening
2. Install L-wrench from fender
into the open threaded hole in
the driven clutch.
3. Turn the L-wrench clockwise
to open the sheaves and
replace the belt.
4. Return the L-wrench to the
fender.
Note: See owners manual for
sheave width adjustment
procedure.
7181093
25
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
7
6
8
5
4
3
9
10
2
11
1
15
14
12
13
17
16
1. Nosepan
2. Skis
3. Front Bumper
4. Hood
10. Rear Bumper
11. Snow Flap
12. Suspension
13. Track
5. Headlight
14. Side Panel
6. Windshield (accessory)
7. Handlebar
8. Operator Seat
9. Taillight
15. Side Panel Fasteners
16. Tool Kit (Inside engine
compartment)
17. L-Wrench
26
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
2
3
4
1
5
6
1. Brake Lever
7
2. Instrument Cluster
(Interactive Digital Display
shown)
1
3. Ignition Switch
4. Engine Stop Switch
5. Throttle Control
6. Recoil Starter Handle
7. Parking Brake Lock
8. Handlebar Grip Warmer
Switch
9. Thumbwarmer Switch
9
8
10
10. POLARIS Electronic Reverse
(PERC) Button
11. Mode/Set Switch
12. Headlight Dimmer Switch
12
11
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Adjustable Headlight
The headlight can be adjusted for vertical aim using the following
procedure.
25 ft. (7.6 m)
Lamp Center Height
X
2 in. (5 cm)
1. In a well-ventilated area, position the snowmobile on a level surface
with the headlight approximately 25 feet (7.6 m) from a wall.
2. Place the rider or the approximate weight of the rider on the seat or
tunnel floorboards.
3. Measure the distance from the floor to the center of the headlight
and make a mark on the wall at the same height.
4. Start the engine. Move the headlight switch to high beam.
5. Observe the headlight aim on
Raise
the wall. The most intense part
of the headlight beam should be
two inches (5 cm) below the
mark on the wall.
6. If adjustment is necessary,
access the headlight adjuster
knob through the left side
panel. Turn the adjuster knob
clockwise to lower the beam.
Turn the adjuster counter-
clockwise to raise the beam.
Lower
28
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Heated Storage Compartment
The storage compartment on
the top of the console is
heated by engine
Heated Storage
(if equipped)
compartment heat. This
compartment can be used to
warm gloves or defog
goggles.
12-Volt Receptacle
If equipped, the 12-volt DC
receptacle is located on the
console next to the
instrument cluster. If not
equipped, the receptacle can
be installed as an accessory.
The 12-volt receptacle is
protected by a 2 AMP fuse.
12-Volt Receptacle
(if equipped)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Saddlebags
Some snowmobiles are equipped
with saddlebags. LOCK & RIDE
saddlebags can be added as an
accessory on other models. Please
see your POLARIS dealer for
more information.
Three (3) locking plungers secure
each saddlebag to the rear cargo
rack. To remove a saddlebag,
open each plunger latch, then pull
the bag away from the rack.
When reinstalling the saddlebags,
always make sure the locking
plungers are secured before
operating.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Fuel Type Selection
Whenever using ethanol, MTBE or other forms of oxygenated gasoline,
the fuel type designation setting must be changed to “Eth” in the gauge.
When using the recommended 91 non-ethanol gasoline, always select
the “91-non” setting. Whenever in doubt of your fuel purchase, use the
“Eth” setting as a safeguard.
Interactive Digital Display (IDD)
If your model is
equipped with the
interactive digital display
Fuel
(IDD), please see your
Selection
IDD Owner’s Manual for
fuel type selection
procedures.
Standard Instrument Cluster
Use the following procedure to change the fuel type designation in the
standard instrument cluster. Refer to the fuel type selection label located
inside the left side panel.
Fuel Type Selection Label
1. Start the engine. Lock the parking brake.
2. Press and release the
SELECT button or SET
switch until “FUEL” is
displayed in the lower
section of the gauge.
3. Press and hold the
SELECT button or SET
Step 2
Step 3
switch until the desired
fuel type is displayed in
the center of the screen.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Detonation Elimination Technology (DET)
The DET system prevents damage to the engine from detonation by
entering an engine protection mode whenever the DET system is active.
When excessive detonation is detected, the check engine light will
illuminate. You may notice decreased engine performance and RPM
when the DET system is activated. In most cases this is temporary and
no action is required. The engine will return to its normal performance
automatically.
Standard Instrument Cluster
Interactive Digital Display (IDD)
If severe detonation occurs, the check engine light will begin to flash
steadily.
• The standard gauge will display “dET”.
• The IDD will display “Detonation Detected - MAG (or PTO)”.
The engine will enter a limp home mode and engine speed will be
limited to 6500 RPM. The engine will remain in this mode until it is
shut down and restarted.
Check Engine Light
Indicates
Solid or Flickering
Steady Flashing
Excessive detonation detected
Severe detonation detected, RPM will be limited
32
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Detonation Elimination Technology (DET)
The most likely causes of severe detonation are outlined in the
troubleshooting table below.
DET Troubleshooting
Cause of DET Activation
Poor quality fuel
Solution
Replace with higher quality fuel
Incorrect ethanol/non-ethanol fuel
type setting
Verify correct fuel type setting on
gauge
Low fuel/no fuel in tank
Water in fuel
Refuel with recommended fuel
Replace with recommended fuel
Plugged fuel filter or tank pick-up sock See your POLARIS dealer for service
Alcohol-based fuel additive used with Do not add deicers or additives that
Ethanol fuel
contain any form of alcohol while
using up to 10% ethanol fuel
Improper engine modifications
Do not modify the engine
33
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Engine Overheat Indicators
Over-Temperature Indicator (Standard Cluster)
The over-temperature
indicator on the standard
instrument cluster will
illuminate when the engine is
overheating. Take action to
cool the engine. See page 35.
The indicator will flash when
engine temperature reaches
critical levels. Stop the
engine immediately.
Overheat Warning (IDD)
The engine temperature scale
at the right side of the IDD
screen changes to RED and
the check engine temperature
indicator at the top left of the
screen illuminates when the
engine is overheating. Take
action to cool the engine. See
page 35.
The indicator will flash when engine temperature reaches critical levels.
Stop the engine immediately.
Please see your IDD Owner’s Manual for more information.
Flashing Indicator
Flashing indicators indicate continued operation could result in serious
engine damage. The engine management system will automatically
reduce engine power and create a misfire condition. Stop the engine
immediately. Allow the engine to cool down.
NOTE: If engine overheating seems to be caused by something other than
poor cooling conditions, see your dealer for service.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Engine Overheat Indicators
Engine-Cooling Actions
If the engine is overheating, promptly take action to cool the engine.
• Drive in loose snow.
• View the coolant level. Do not open the pressure cap while the engine
is hot. Add coolant if the level is low.
• Stop the engine and allow it to cool down.
NOTICE: If you must continue to operate while the indicator light is illuminated,
drive slowly and stop the engine frequently to allow it to cool down.
Security System (Ignition Lock System)
Your snowmobile has an optional security function that can be activated
by an authorized POLARIS dealer. If you have this feature activated,
you can lock the ignition to prevent unauthorized use when leaving the
snowmobile unattended. A locked system will limit engine speed to
3000 RPM, which prevents clutch engagement, and the snowmobile
will not move when throttle is applied.
If you wish to use this system, see page 43 for security system activation
and operating instructions (standard instrument cluster). If your model is
equipped with the Interactive Digital Display (IDD), please see the IDD
Owner’s Manual provided with your snowmobile.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information
Center
Check Engine
High Beam
Indicator
Indicator
Over-Tem-
perature Indi-
cator
Parking Brake
Indicator
Reverse
Indicator
Low Oil
Indicator
SELECT
Button
MODE
Button
The instrument cluster contains
indicator lights and the rider
information center. The information
center can be controlled by either the
MODE and SELECT buttons on the
instrument cluster or by the MODE/
SET switch on the left handlebar.
NOTICE: Certain products will damage
the lens and other plastic
surfaces. Do not use alcohol to
clean the instrument cluster.
Immediately clean off any
gasoline that splashes on the
instrument cluster.
MODE
SET
CAUTION! The speedometer may give wrong values at the existence of
electromagnetic radiation >= 10 V/m.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Indicators
Check Engine Indicator
This indicator appears if an EFI-related fault occurs. Do not operate the
snowmobile if this warning appears. Serious engine damage could
result. See your dealer. See page 92 for diagnostic code definitions.
Over-Temperature Indicator
This indicator illuminates to alert the operator that the engine is
overheating. The operator should take action to cool the engine. If the
indicator flashes, continued operation could result in serious engine
damage. Stop the engine immediately.
Low Oil Indicator
The low oil indicator light may flicker at times due to oil movement in
the bottle, but when the light comes on and remains on, add the
recommended oil before further operation. See page 80.
High Beam Indicator
The high beam indicator illuminates when the lights are set to high
beam.
Parking Brake Indicator
This indicator illuminates when the parking brake is engaged. It will
also illuminate when the service brake is in use. See page 70.
Reverse Indicator
This indicator flashes when the snowmobile is in reverse. See page 85.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
The rider information center is located in the instrument cluster. The
center displays vehicle speed, engine speed, odometer, resettable trip
meters (2), total engine hours of operation, fuel level, engine
temperature and diagnostic display mode.
Setting changes must be made with the engine running or with the
vehicle powered by an external DC power supply connector.
The information center is set to display standard units of measurement
for distance and temperature. To change to metric units, see page 42.
3
1
2
6
4
5
38
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
1. Information Display Area - This area displays either engine speed
or vehicle speed (whichever is not displayed in the speed display),
engine temperature and maximum vehicle speed. To change the dis-
play, see page 40.
2. Speed Display - The speed display area displays either vehicle
speed or engine speed. To change the display, see page 40.
3. Fuel Gauge - The segments of the fuel gauge show the level of fuel
in the fuel tank. When the last segment clears, a low fuel warning is
activated. All segments including the fuel icon will flash. Refuel
immediately.
Tip: If the fuel icon fails to display, an open or short circuit has occurred in the
fuel sensor circuit. See your dealer.
4. Odometer/Engine Hour Display - This area displays the odometer,
Trip A, Trip B and engine hours. To change the display, see page 41.
5. Battery Power - This indicator illuminates when battery power is
low.
6. Playback Icon - The playback function allows the rider to record
and play back engine speed, vehicle speed and throttle position sen-
sor information for up to three minutes. The playback icon flashes
while recording. See page 41.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Speed Display Area
The speed display area displays either vehicle speed or engine speed.
Vehicle speed is displayed in either miles per hour (MPH) or kilometers
per hour (km/h). Engine speed is displayed in revolutions per minute
(RPM).
1. To change which item displays, first make sure the information
display area is set to display either engine speed or vehicle speed.
2. Press and hold the MODE button (on the instrument cluster) or the
MODE switch (on the left handlebar) for three seconds.
Information Display Area
This area displays either engine speed or vehicle speed (whichever is
not displayed in the speed display), engine temperature and maximum
vehicle speed. To change the display, press and release the MODE
button or the MODE switch until the desired item is displayed.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Odometer/Engine Hour Display Area
This area displays the odometer, Trip A meter, Trip B meter and engine
hours meter.
The odometer displays the total distance traveled by the vehicle since
manufacture. Each trip meter records the distance traveled by the
vehicle on a trip if the meter is reset before each trip. The engine hour
meter displays the total hours the engine has been in operation since
manufacture.
To change the display, press and release the SELECT button or the SET
switch until the desired item is displayed.
To reset a trip meter, press and hold the SELECT button or the SET
switch until the meter resets to zero.
Playback Function
The playback function allows the rider to record and play back engine
speed, vehicle speed and throttle position sensor information for up to
three minutes.
1. To begin recording, simultaneously press and hold the MODE and
SELECT buttons on the instrument cluster for three seconds. The
playback indicator will flash while the instrument cluster is
recording.
2. To play back the recorded data, stop the vehicle and wait for engine
speed to drop below clutch engagement.
3. Simultaneously press and release the MODE and SELECT buttons
on the instrument cluster.
4. Applying the throttle will clear the display and return the instrument
cluster to normal operation.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Standard/Metric Display
The odometer and temperature displays can be viewed in either standard
or metric units of measurement. Both displays change if units are
changed. The new settings will remain until changed by the operator.
Change Method 1
1. Press and release the MODE button or MODE switch until engine
temperature displays.
2. Press and hold the MODE button or MODE switch until the units
change.
Change Method 2
1. Press and release the SELECT button or SET switch until the
odometer displays.
2. Press and hold the SELECT button or SET switch until the units
change.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Security System (Ignition Lock System)
This system is an optional feature and will not function until it has been
activated by your authorized POLARIS dealer. If you have this feature
activated, you can lock the ignition to prevent unauthorized use when
leaving the snowmobile unattended. A locked system will limit engine
speed to 3000 RPM, which prevents clutch engagement, and the
snowmobile will not move when throttle is applied.
If you wish to use this feature, you must complete all four tasks on the
following pages to have your system activated and to change the
security code to one of your own choosing.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Security System (Ignition Lock System)
First Time Use of Your Security System
Perform all tasks in the order shown if you wish to activate and use the
optional security system.
TASK 1: Activate the security system
See your authorized POLARIS dealer to have the optional security system
feature activated in the electronic control unit (ECU).
TASK 2: Lock the System the First Time
1. Start the engine and lock the parking brake.
2. Press and hold the MODE and SEL buttons for 3
seconds, then release. SECURE OFF should be
displayed. If not, repeat this step.
3. Wait until ENTER CODE displays, then press
and release SEL to advance the digit. When “0”
is displayed, press and release MODE to accept
the digit. TIP: If the ENTER CODE screen exits
due to inactivity, repeat step 2.
4. Press and release SEL to advance the second
digit. When “0” is displayed, press and release
MODE to accept the digit.
5. Press and release SEL to advance the third digit.
When “0” is displayed, press and release MODE
to accept the digit.
6. After accepting the third digit, view the display
screen. SECURE ON displays if the system locks.
NOTE: The system is now locked.
7. You must now unlock the system. Proceed
immediately to TASK 3.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Security System (Ignition Lock System)
First Time Use of Your Security System
TASK 3: Unlock the System
1. When the engine is running, the display will
alternate between SECURE ON and
ENTER CODE. Wait until ENTER CODE
displays, then press and release SEL to
advance the digit. When “0” is displayed,
press and release MODE to accept the
digit.
2. Press and release SEL to advance the second
digit. When “0” is displayed, press and release
MODE to accept the digit.
3. Press and release SEL to advance the third digit.
When “0” is displayed, press and release MODE
to accept the digit.
4. After accepting the third digit, view the display
screen. SECURE OFF displays if the system
unlocks.
NOTE: The system is now unlocked.
5. You must now enter a new security code. Proceed immediately to TASK 4.
TASK 4: Enter Your New Security Code
1. Immediately after locking and unlocking the system, and while SECURE
OFF is displayed, press and release the MODE button to bring up the
ENTER CODE screen.
2. When ENTER CODE displays, use the SEL and MODE buttons to select
and accept each digit of a new personal security code.
3. After accepting the third digit, view the display
screen. The new code and CODE SET will
888
display if the system accepted your new code.
You will not see this display again.
NOTE: Your new code is now set. The system is
NOT locked.
4. Record your new security code in a safe place for future reference.
Record your new personal security code here: __________________
TIP:If you lose your personal security code, see your dealer to have the code
reset to “000”. Then perform TASK 2 through TASK 4 to change the code
to one of your own choosing.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Security System (Ignition Lock System)
Locking the System With Your Personal Security Code
1. Start the engine and lock the parking brake.
2. Press and hold the MODE and SEL buttons
for 3 seconds, then release. SECURE OFF
should be displayed. If not, repeat this step.
3. Wait until ENTER CODE displays, then
press and release SEL to advance the digit.
When the first digit of your security code is
displayed, press and release MODE to
accept the digit.
TIP:If the ENTER CODE screen exits due to inactivity,
repeat step 2.
4. Continue to use SEL and MODE to select
and accept the remaining two digits of the
code.
5. After accepting the third digit, view the dis-
play screen. SECURE ON displays if the
system locks. Engine speed is now limited
and the snowmobile cannot be driven.
TIP:When the engine is running, the display will
alternate between SECURE ON and ENTER CODE.
6. If BAD CODE displays, the screen will then
return to the ENTER CODE screen. Repeat
steps 3-5 to re-enter the security code.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Security System (Ignition Lock System)
Unlocking the System With Your Personal Security Code
1. When the engine is running, the display
will alternate between SECURE ON and
ENTER CODE. Wait until ENTER
CODE displays, then press and release
SEL to advance the digit. When the first
digit of your security code is displayed,
press and release MODE to accept the digit.
TIP:When the system is locked and engine temperature is above 120° F (49°
C), the correct password must be entered within 60 seconds or the engine
will shut down.
2. Continue to use SEL and MODE to select
and accept the remaining two digits of the
code.
3. After accepting the third digit, view the
display screen. SECURE OFF displays if
the system unlocks.
4. Re-enter your code if BAD CODE
displays.
NOTE: The system is now unlocked.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Security System (Ignition Lock System)
Changing to a New Security Code
Any time you wish to change your current security code to a new code,
perform TASK 2 through TASK 4 of the First Time Use of Your
Security System procedure beginning on page 44. Instead of using the
factory default code “000” in TASK 2 and TASK 3, use your current
security code.
Security System Access Quick Reference
Now that you have become familiar with the procedure for locking and
unlocking the system, use the chart below as a quick reference.
Security System Access Quick Reference Chart
Action
Result
Start engine + Lock
parking brake + Press
and hold both MODE +
SELECT (SEL)
Displays ENTER CODE (to lock the system)
Press SELECT (SEL)
Press MODE
Advances a digit on the ENTER CODE screen
Accepts a digit and displays the next digit position (if
any remain) on the ENTER CODE screen
or
Opens ENTER CODE screen if MODE is pressed
immediately after locking and unlocking the system
(to change your security code)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Standard Instrument Cluster
Rider Information Center
Diagnostic Display Mode
The diagnostic display mode is for informational purposes only. Please
see your POLARIS dealer for all major repairs.
The diagnostic mode is accessible only when the check engine warning
indicator is illuminated and a diagnostic code is active.
Do not stop the engine if you want to view the active code (failure
code). Active codes cannot be retrieved if power is interrupted to the
instrument cluster. The codes will become inactive codes if power is
interrupted. Inactive codes are stored in the history of the unit. Please
see your POLARIS dealer to retrieve inactive codes.
Use the following procedure to view active codes.
1. Do not stop the engine.
2. With the brake engaged, press and release the SELECT button or
SET switch to toggle to the diagnostic display mode. When a code
is active, the diagnostic display mode will appear immediately
following the engine hour display.
TIP:When the diagnostic mode is displayed, the check engine warning indicator
will begin to flash.
3. A set of two numbers will appear in the display.
• The 2-6 digit suspect parameter number (SPN) in the information display
area indicates which component is generating the fault code.
• The 1-2 digit failure mode indicator (FMI) number in the odometer area
indicates the fault mode, such as open or short circuit.
4. More than one fault may be active. Press and hold the MODE
button or MODE switch for two seconds to toggle to the next active
code. Repeat until all codes are retrieved.
5. See page 92 for code definitions and failure descriptions.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Interactive Digital Display (IDD)
5-Button
Keypad
Display
Screen
The Interactive Digital Display (IDD) provides the rider with:
• Speedometer
• Tachometer
• Odometer
• 2 Trip Meters
• Fuel Level Indicator
• Coolant Temperature
• Battery Voltage
• Fuel Type Selection
• Vehicle Security
The IDD also offers GPS mapping and
Bluetooth® connectivity for
compatible smartphones/devices. This
feature will display text messages and
missed phone calls on the display
screen.
The IDD sub-menus and most display
features are controlled by either the
five button keypad on the IDD or by
the MODE/SET switch on the left
handlebar.
SET
MODE
Please see your IDD Owner’s Manual for more information.
NOTICE: Use a microfiber hand towel to clean the LCD screen. Certain
products will damage the screen and other plastic surfaces. Do not
use alcohol to clean the display screen. Immediately clean off any
gasoline that splashes on the instrument cluster.
CAUTION! The speedometer may give wrong values at the existence of
electromagnetic radiation >= 10 V/m.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Set-Up Guide
Introduction
The front suspension and PRO-XC rear suspension on your AXYS
snowmobile is incredibly easy to adjust. Just remember three simple
steps:
1. Ride your snowmobile!
2. Adjust the rear track shock spring to tune vehicle balance (ski
pressure and weight transfer).
3. Adjust shock clickers to tune ride quality (stiffer or softer ride).
Step 1: Ride your snowmobile!
Ride the snowmobile in various terrain to fully experience the existing
suspension settings before making any adjustments.
Step 2: Adjust the rear spring to tune vehicle balance.
After riding the snowmobile, you should be able to determine if the
snowmobile needs more “bite” or needs to be more “lite”. If the steering
needs more “bite”, increase the rear track spring preload or decrease the
front track spring preload.
If you prefer your snowmobile has lighter steering, decrease the rear
track spring preload or increase the front track shock spring preload.
At the front of the snowmobile, if you prefer a taller ride height,
increase the front suspension shock spring preload settings. Likewise, if
you prefer your snowmobile has a lower ride height, you can decrease
the front suspension shock spring preload settings.
Step 3: Adjust shock clickers for ride quality.
You can adjust the shock clickers to control bottoming and adjust ride
comfort. Turning a clicker counter-clockwise decreases damping for a
softer ride. Turning a clicker clockwise increases damping for a stiffer
ride and less bottoming.
NOTICE: Always adjust the clicker at least one click below full stiff (full
clockwise) or shock damage will occur.
Test ride the snowmobile and continue making spring and clicker
adjustments until you achieve the perfect ride.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Set-Up Guide
Ride Experience Table
Ride Experience
Adjustment
Too “LITE”
•Ski pressure is too light
•Skis push
Increase rear track shock
spring preload
OR
Decrease front track shock
spring preload
Too much “BITE”
•Ski pressure is too heavy
•Steering is heavy
Decrease rear track shock
spring preload
OR
Increase front track shock
spring preload
Front Suspension (IFS Shocks):
Too Stiff
Too Soft
(IFS Shocks)
Turn clickers 2 clicks SOFT
Turn clickers 2 clicks HARD
Ride Comfort Under Feet (Front Track Shock):
Too Stiff
Too Soft
(Front Track Shock)
Turn clicker 2 clicks SOFT
Turn clicker 2 clicks HARD
Rear Suspension (Rear Track Shock):
Too Stiff
Too Soft
(Rear Track Shock)
Turn clicker 2 clicks SOFT
Turn clicker 2 clicks HARD
Shock Locations
REAR TRACK SHOCK
FRONT (IFS) SHOCKS
FRONT TRACK SHOCK
MORE LITE
52
MORE BITE
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Set-Up Guide
Front Suspension (IFS) Factory Spring Settings
Spring Setting
Model
Spring Rate
Preload
(Factory
Setting)
Preload
(Minimum (Maximum
Setting) Setting)
Preload
Spring
Part
Number
lb/in N/mm
in
cm
in cm in cm
2-1/2 6.4 2-1/2 6.4 3-1/2 8.9 7043732
100 17.5 4-1/2 11.4 4-1/2 11.4 4 3/4 12 7041576
80 14 2-1/2 6.4 2-1/2 6.4 3-1/2 8.9 7043732
RUSH PRO-S
RUSH PRO-X
80
14
SWITCHBACK
PRO-S
SWITCHBACK
PRO-X
100 17.5 4-1/2 11.4 4-1/2 11.4 4 3/4 12 7041576
80 14 2-1/2 6.4 2-1/2 6.4 3-1/2 8.9 7043732
100 17.5 4-1/2 11.4 4-1/2 11.4 4 3/4 12 7041576
SWITCHBACK
ADVENTURE
SWITCHBACK
ADVENTURE
(International)
CAUTION! Never exceed the minimum/maximum spring preload settings.
Always remove the vehicle weight from the spring prior to making adjustments.
Front Suspension (IFS) Factory Clicker Settings
Model
Clicker Setting
(from full soft)
All PRO-S Models
3
6
3
6
All PRO-X Models
SWITCHBACK ADVENTURE
SWITCHBACK ADVENTURE
(International)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Set-Up Guide
Front (IFS) Shock Adjustments
SOFTER
STIFFER
LOWER
TALLER
54
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Set-Up Guide
Front Track Shock Factory Spring Settings
Spring Setting
Model
Spring Rate
Preload
(Factory
Setting)
Preload
(Minimum (Maximum
Setting) Setting)
Preload
Spring
Part
Number
lb/in N/mm
in
cm
in cm in cm
RUSH PRO-S
RUSH PRO-X
95-280 16.6-49 1-1/2 3.8 1-1/2 3.8 1.85 4.7 7043957
150 26 2.54 2.54 1-1/4 3.17 7043678
95-280 16.6-49 1-1/2 3.8 1-1/2 3.8 1.85 4.7 7043957
1
1
SWITCHBACK
PRO-S
SWITCHBACK
PRO-X
150
95-280 16.6-49 1-1/2 3.8 1-1/2 3.8 1.85 4.7 7043957
150 26 2.54 2.54 1-1/4 3.17 7043678
26
1
2.54
1
2.54 1-1/4 3.17 7043678
SWITCHBACK
ADVENTURE
SWITCHBACK
ADVENTURE
(International)
1
1
CAUTION! Never exceed the minimum/maximum spring preload settings.
Always remove the vehicle weight from the spring prior to making adjustments.
Front Track Shock Factory Clicker Settings
Model
Clicker Setting
(from full soft)
All PRO-S Models
3
6
3
6
All PRO-X Models
SWITCHBACK ADVENTURE
SWITCHBACK ADVENTURE
(International)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Set-Up Guide
Front Track Shock Adjustments
SOFTER
MORE LITE
MEASURE HERE
STIFFER
MORE BITE
56
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Set-Up Guide
Rear Track Shock Factory Spring Settings
Spring Setting
Model
Spring Rate
Preload
(Factory
Setting)
Preload
(Minimum (Maximum
Setting) Setting)
Preload
Spring
Part
Number
lb/in N/mm
in
cm
in
2
cm
in cm
3-1/2 8.9 7041575
1.2 2-1/2 6.4 7043160
3-1/2 8.9 7041575
RUSH PRO-S
RUSH PRO-X
120
150
120
21
26
21
2-3/4
7
5
1-1/2 3.8
2-3/4
1/2
2
SWITCHBACK
PRO-S
7
5
SWITCHBACK
PRO-X
150
120
150
26
21
26
1-1/2 3.8
2-3/4
1-1/2 3.8
1/2
2
1.2 2-1/2 6.4 7043160
3-1/2 8.9 7041575
SWITCHBACK
ADVENTURE
7
5
SWITCHBACK
ADVENTURE
(International)
1/2
1.2 2-1/2 6.4 7043160
Optional HD Spring - RUSH / SWITCHBACK PRO-S ONLY
(Rider Weight Range = 200-350 lbs (90-160 kg)
PRO-S (Heavy)
150
26
1-1/2 3.8
1/2
1.2 2-1/2 6.4 7043160
CAUTION! Never exceed the minimum/maximum spring preload settings.
Always remove the vehicle weight from the spring prior to making adjustments.
Rear Track Shock Factory Clicker Settings
Model
Clicker Setting
(from full soft)
All PRO-S Models
3
6
3
6
All PRO-X Models
SWITCHBACK ADVENTURE
SWITCHBACK ADVENTURE
(International)
57
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Setup Guide
Rear Track Shock Adjustments
SOFTER
MORE BITE
STIFFER
MORE LITE
58
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Suspension Quick Setup Guide
Limiter Strap Adjustment
The front torque arm limiter strap is set at position #1.
MORE BITE
MORE LITE
POLARIS recommends leaving the limiter strap length at position #1 to
maintain the optimum ride characteristics of the snowmobile. Riders
who desire less ski pressure and more weight transfer toward the rear of
the snowmobile can lengthen the limiter strap by changing to position
#2.
1. Loosen the lock nut.
2. Adjust the limiter strap.
3. Tighten the lock nut.
Torque: 17 ft-lbs (23 Nm).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Handlebar Adjustments
Riser Angle
Riser angle can be adjusted to suit rider preference. Factory settings are
shown below.
PRO-S Models - 0°
PRO-X Models - 11° Forward
1. Loosen the four bolts on the bottom of the adjuster block. If
necessary, pry the blocks apart with a screwdriver.
2. Adjust the riser forward or rearward to the desired position.
3. Tighten the bolts to 14.8 ft-lbs (20 Nm).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Handlebar Adjustments
Handlebar Angle
Handlebar angle can be adjusted to suit rider preference. Factory
settings are shown below.
PRO-S Models - 30°
PRO-X Models - 30°
1. Loosen the four bolts on the top riser block.
2. Adjust the handlebar upward or downward to the desired angle. Be
sure the handlebar, brake lever and throttle lever operate smoothly
and do not hit the gas tank, windshield or any other part of the
machine when turned fully to the left or right. If necessary, loosen
the set screws for the left and right controls, rotate the controls
slightly, then tighten the set screws to the proper torque. See page
62.
NOTICE: Do not stretch wires while adjusting the controls. Stretching the wires
could damage the handwarmers.
3. Tighten the bolts.
Torque: 14.8 ft-lbs (20 Nm)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Handlebar Component Fastener Torques
Shown with riser cover removed for clarity
4
5
8
1
2
3
6/7
4
Component
Torque
Do not over-tighten
20 in-lbs (2.3 Nm)
70 in-lbs (7.9 Nm)
Hand-Tight
1. Left Handlebar Control Block
2. Brake Lever / Master Cylinder
3. Hand Guard Mounts (if applicable)
4. Upper / Lower Riser Clamps
5. Auxiliary Engine Stop Switch Set Screw
6. Throttle Lever Block Set Screw
7. Throttle Lever Block Cover Screws
8. Riser
14.8 ft-lbs (20 Nm)
12 in-lbs (1.4 Nm)
27 in-lbs (3.1 Nm)
6 in-lbs (0.7 Nm)
-
62
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Handlebar Component Locations
Refer to the following illustration and measurements to position
handlebar components at factory-specified locations.
Handlebar Component Alignment Measurements
1. .011 in. (3 mm)
2. 6.65 in. (169 mm)
3. 6.7 in. (170 mm)
4. 10 in. (254 mm)
5. .47 in. (12 mm)
6. .08 in. (2 mm)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Traction Products
Studs
The track is not warranted by POLARIS if studs have been installed.
Track warranties are also void if track damage or failure results from the
use of any non-POLARIS traction products. Use only POLARIS-
approved traction products on your snowmobile.
If you choose to install studs, stud length must not exceed 1.325 inches
(3.7 cm) for a factory-installed track.
See your dealer about installing studs and/or carbides.
NOTICE: Use of studs longer than the recommended length on snowmobiles
equipped with center coolers will result in center cooler damage or
damage to the tunnel.
Track studding will enhance braking control on hard-packed snow or
ice, but extreme caution is still required on such surfaces. Steering
ability may be reduced on hard-packed snow or ice.
When studded tracks are used, increased wear to the brake pads will
result from increased braking and requires increased brake inspection
intervals.
Installing studs can also cause the track to stretch more than a non-
studded track. For this reason, POLARIS recommends inspecting track
tension more often and setting the tension at the preferred measurement.
Always adhere to the manufacturer’s stud maintenance procedures and
stud nut torque specifications.
NOTICE: Aggressive studding patterns may require grinding protruding stud
bolts flush to prevent idler wheel damage. Maintain track tension on
studded tracks on the tight side of the specification to prevent heat
exchanger damage. The center of the stud must be at least 1 1/8 inch
(2.9 cm) from the outside edge of the track.
Before equipping your snowmobile with traction products, be aware of
regulations pertaining to the use of traction products in your area of
operation.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
THE PERFECT FIT
Traction Products
Carbide Skags
A skag is a replaceable bar attached to the underside of the ski to assist
in turning the snowmobile and to prevent ski wear caused by contact
with roads and other bare terrain. Use carbide skags with studded tracks
to help maintain proper steering and control. See page 125.
Maintain a proper balance between the number of studs and the length
of carbide on the skags (the more studs you use, the longer the carbide
on the skags should be). See your dealer's track studding chart.
Wear Strips
Your snowmobile is equipped with integrated stud protection that will
protect the cooling system and tunnel when using a maximum stud
length of 1.325 inches (3.7 cm) for all tracks.
See your dealer’s studding chart for recommended traction accessories.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-RIDE INSPECTIONS
Pre-Ride Checklist
Inspect all items on the checklist for proper operation or condition
before each use of the snowmobile. Procedures are outlined on the
referenced pages.
Item
See Page
Drive Belt Condition
Steering System
Recoil Rope
115
71
71
Coolant Level
105
98
Chaincase Oil Level
Injection Oil Level
80
Parking Brake Lock/Brake Lever/Brake System
Auxiliary Shut-Off Switch (Engine Stop Switch)
Ignition Switch
69, 70, 110
72
72
Headlight/Taillight/Brake Light
Suspension Mounting Bolts
Skags (Wear Bars)
72
67
125
67
Ski Saddle and Spindle Bolts
Hood and Side Panel Fasteners
Throttle Lever / Throttle Release Switch
Rear Wheel Idler Bolts
94-95
81, 82
121
72
Tether Switch/Strap (if equipped)
Track Alignment/Condition
71, 122
128
Rail Slide Condition
66
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-RIDE INSPECTIONS
Pre-Ride Suspension Inspection
Loose nuts and bolts can reduce your snowmobile’s reliability and cause
needless repairs and down time. Before beginning any snowmobile trip,
a visual inspection will uncover potential problems. Check the
following items on a weekly basis or before any long trip.
Item
See Page
Check suspension mounting bolts for tightness.
Check rear idler wheel bolts for tightness.
Check rear idler adjusting bolt locknuts for tightness.
Check front torque arm limiter strap condition.
Check rail slide condition.
See Dealer
121
--
--
128
120
125
123
--
Check track tension.
Check ski runner/skag condition.
Check ski spindle bolts for tightness.
Check tie rod end nuts for tightness.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-RIDE INSPECTIONS
Before Starting the Engine
Before starting the engine, always refer to all safety warnings pertaining
to snowmobile operation. Never start the engine without checking all
vehicle components to be sure of proper operation.
WARNING! Operating the vehicle with worn, damaged, or malfunctioning
components could result in serious injury or death. Never start the engine
without checking all vehicle components to be sure of proper operation.
Read and Understand Your Owner's Manual
Read the Owner’s Manual completely and refer to it often. The manual
is your guide to safe and enjoyable snowmobiling experience.
Throttle Lever
The throttle and brake are the primary controls of your snowmobile.
Always make sure both are functioning properly.
Squeeze the throttle lever to
make sure it compresses evenly
and smoothly. When released,
the lever should immediately
return to the idle position
without binding or hesitation. If
the throttle does not function
smoothly, or if you discover
excessive lever freeplay, DO
NOT start the engine. Have the
throttle serviced immediately.
Throttle Release Switch
Test the throttle release switch system before operating the snowmobile.
See page 81.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-RIDE INSPECTIONS
Before Starting the Engine
Brakes
Always check the following items for proper operation before starting
the engine.
Brake Lever Travel
NOTICE: Do not pump the brake
lever when performing
this procedure.
Squeeze the brake lever. It
should move no closer to the
handgrip than 1/2 inch (1.3
cm). A smaller distance
1/2” (1.3 cm)
indicates low brake fluid level
or air in the hydraulic system.
Refer to the brake bleeding
information on page 112 or see
your dealer for service.
Lever Feel
If the brake lever feels “spongy” when squeezed, check the brake fluid
level and condition. Add fluid as needed. See page 111.
WARNING! Continued use of “spongy” brakes may cause a complete loss of
brakes, which could result in serious injury or death. Always have the brakes
serviced at the first sign of sponginess.
Brake Fluid Level
Position the handlebars so
the brake fluid reservoir is as
close to level as possible.
View the fluid level through
the reservoir (shaded in
8 mm MAX
10 mm MIN
illustration). If the level is
below the MIN (minimum)
level specification, add
POLARIS DOT 4 brake
fluid. See page 111.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-RIDE INSPECTIONS
Before Starting the Engine
Parking Brake Lever Lock
Use the parking brake lever lock only when you want the snowmobile to
remain stationary; for example, when parked on an incline for a period
of five minutes or less.
1. Brake Lever
2
3
4
1
2. Fluid Level Indicator
3. Master Cylinder
Reservoir/Cover
4. Parking Brake Lever
Lock
Lock Engagement
To engage the lock, squeeze the brake lever tightly and push forward on
the lock. Hold the lock forward while releasing the brake lever.
TIP:If the brake lever is squeezed tightly enough, the lock will move freely into
place. Do not force the lock or it may break.
The parking brake light will illuminate if the parking brake lever lock is
set while the engine is running. It will also illuminate when the service
brake is in use. If the parking brake light does not come on when the
parking brake or service brake is in use, have it serviced by your dealer.
Lock Release
To release the lock, squeeze the brake lever tightly. The lock will return
to the unlocked position.
WARNING! If the parking brake lever lock is partially or entirely engaged while
riding, the brakes may overheat, resulting in brake damage. In extreme cases it
could cause a fire, which could result in serious injury or death. Always ensure
that the lever lock is completely disengaged before operating the snowmobile.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-RIDE INSPECTIONS
Before Starting the Engine
Steering System
WARNING! Ice and snow build-up may interfere with the steering of your
snowmobile, resulting in serious injury or death. Keep the underhood area free
of snow and ice.
Before driving, manually turn the skis to the left and right to be sure ice
and snow are not interfering with full left and right steering. If difficulty
is encountered, remove ice and snow build-up that may be obstructing
the steering linkage.
Track
Track damage or failure caused by operation on ice or poor lubrication
conditions voids the track warranty.
WARNING! Operating the snowmobile with a damaged track increases the
possibility of track failure, which could cause loss of control resulting in serious
injury or death. Always inspect the track for damage before using the vehicle.
WARNING! Use of traction products such as studs increases the possibility of
track damage and/or failure. Driving at high speeds for extended periods of time
in marginal lubrication could severely damage track rods, break track edges,
and cause other track damage. Examples of marginal lubrication would include
frozen bodies of water without snow cover, icy trails and no-snow conditions.
Side Panel Fasteners
The side panels of the snowmobile protect the operator from moving
parts. Never operate the engine with the side panels open or removed.
Recoil Rope
Inspect the recoil rope and handle
for excessive wear, and make sure
the knot securing the rope inside
the handle is secure. If excessive
wear is found, see your POLARIS
dealer for replacement.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-RIDE INSPECTIONS
Start the Engine and Check
Before starting the engine, always refer to all safety warnings pertaining
to snowmobile operation. Never engage the starter when the engine is
running. Never start the engine without checking all vehicle components
to be sure of proper operation. See Before Starting the Engine beginning
on page 68.
Auxiliary Engine Stop Switch
Check the auxiliary shut-off switch for proper operation. Push the
switch down to stop the engine. Pull it up to allow restarting.
Ignition Key Switch
Make sure the engine stops when the ignition key switch is turned to
OFF.
Tether Switch (if equipped)
If your snowmobile has a tether switch, remove the tether from the
switch to make sure the engine stops immediately.
Lighting
Check the headlight (high and low beam), taillight and brake light.
Make sure all lights work properly before operating.
Mirrors (if equipped)
Adjust the mirrors so they can be used to their full advantage.
Operating Area
Before driving away, check your surroundings. Be aware of obstacles
and make sure bystanders are a safe distance from the snowmobile.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Ignition Switch
The ignition switch has three positions.
OFF
Vehicle / IDD power off
RUN
Vehicle / IDD power on
START
Activates starter motor (if equipped)
If equipped with electric start, turn the key to
START to crank the engine. When the key is
released, it automatically returns to the RUN position.
Snowmobiles equipped with electric start and/or IDD are equipped with
a battery. If the key remains in the RUN position after using the engine
stop switch to stop the engine, the IDD remains active. The IDD screen
will turn off after several minutes of inactivity, but the IDD will
continue to draw a small amount of current from the battery until the
key is turned off. This feature is useful for accessing the IDD without
starting the engine, but turn the key off when the IDD is not in use.
The IDD is not dependent on the battery while the engine is running, but
the battery supplies a constant power source when the engine is turned
off or when the engine is transitioning between forward and reverse
operation. If the battery is not installed, the IDD reboots when the
engine is started and when electronic reverse (PERC) is used.
Emergency Stopping
The following chart lists methods for stopping the snowmobile in the
event of an emergency. See page 81 for more information about the
engine stop switch and throttle release switch.
SYSTEM
Ignition Switch
WHAT IT DOES
Interrupts ignition circuit
Brake
Slows jackshaft
Auxiliary Engine Stop Switch
Throttle Release Switch
Interrupts ignition circuit
Enables Engine Control Unit (ECU)
software RPM limit
Tether Switch (Option)
Interrupts ignition circuit
73
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Starting the Engine
NOTICE: Engaging the starter when the engine is running WILL result in serious
engine damage, especially if the snowmobile is in reverse. Never
engage the starter when the engine is running.
1. Turn the key to the RUN position.
2. Pull the auxiliary engine stop switch up to the RUN position.
3. If equipped with electric start, turn the key to START to crank the
engine. Release the key to the RUN position when the engine starts.
4. If not equipped with electric start, grasp the starter handle and pull
slowly until the recoil engages; then pull abruptly to crank the
engine.
TIP:Don't pull the starter rope to the fully extended position and don't allow it to
snap back into the housing. Damage may result.
5. If the engine does not start after several attempts, slightly depress
the throttle (no more than 1/4 inch (6 mm) open) while cranking the
engine. When the engine starts, immediately release the throttle.
CAUTION! To avoid injury and/or engine damage, do not operate the electric
starter or pull-rope starter while the engine is running.
NOTICE: Operating the vehicle immediately after cold starting could cause
engine damage. Allow the engine to warm up for several minutes
before operating the vehicle. If cold drive-away is attempted, the
engine RPM may stumble slightly to protect the engine.
Restarting an Engine
If the rider stops the engine by pushing the engine stop switch down,
restart the engine using the normal starting procedure. If the engine fails
to start using the normal procedure:
1. Push the engine stop switch down to the OFF position.
2. Turn the key to the OFF position.
3. With both switches OFF, squeeze and hold the throttle in the wide
open position.
4. Crank the engine several times to draw fresh air through the engine.
5. Release the throttle.
6. Restart the engine using the normal starting procedure.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Break-In Period
Engine Break-In
Always follow these recommended break-in procedures for new or
rebuilt engines. The first tank of fuel is considered the break-in period
for the engine.
Premix the first tank of fuel and fill the oil reservoir as outlined below.
Oil added to the fuel and oil injection systems will provide the necessary
engine lubrication.
Oil Recommendations
First Tank of Fuel:
After Break-in:
POLARIS VES 2-Cycle Oil
POLARIS VES 2-Cycle Oil
See page 137 for the part numbers of POLARIS products.
Never mix brands of oil. Serious chemical reactions can cause injection
system blockage, resulting in serious engine damage. Oils may also be
incompatible and the result could be sludge formation, filter blockage,
and reduced cold weather flow rates. All POLARIS oils are compatible
with each other.
Initial Fuel Premix
Always premix fuel in 5-gallon (19-liter) increments in a separate fuel
container. Never add oil directly to the fuel tank.
Fuel
VES 2-Cycle Oil
Ratio
Each 5 gal. (19 l)
16 oz. (473 ml)
40:1
75
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Break-In Period
Engine Break-In
Excessive heat build-up during the first three hours of operation will
damage close-fitted engine parts. Do not operate at full throttle or high
speeds for extended periods during the first three hours of use. Vary the
throttle openings and vehicle speeds to reduce friction on all close-
fitting machined parts, allowing them to break in slowly without
damage.
NOTICE: Use of any lubricants other than those recommended by POLARIS
may cause serious engine damage. We recommend the use of
POLARIS lubricants for your vehicle.
Drive with extra caution during the break-in period. Perform regular
checks on fluid levels, lines, and all other important areas of the
snowmobile.
Oil Injection System
Always check and fill the oil bottle when refueling. See page 80.
NOTICE: Serious engine damage can occur without the proper lubrication.
Check the oil bottle level often during the first tank of fuel. If the oil
level doesn't go down, contact your dealer immediately.
Drive Belt Break-In
The break-in period for a new drive belt is 30 miles (48 km). During this
time, vary the throttle position under 50% and limit full throttle use.
Always take time to warm up the belt and driveline prior to operating
the snowmobile. Free the track and skis from the ground before
engaging throttle.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Track Warm-Up
WARNING! A loose track or flying debris could cause serious injury or death.
Stand clear of the front of the snowmobile and the moving track. Never hold the
snowmobile up or stand behind it while warming up the track. Do not use
excessive throttle during warm-up or when the track is free-hanging. Use a
stable rear support.
WARNING! Use of traction products such as studs will increase the possibility
of track damage and/or failure. This could cause loss of control, resulting in
serious injury or death. Always inspect for track damage before operating the
snowmobile.
Follow these steps to ensure proper warm-up of the engine, drive train
and track.
1. Never rotate a dry track. For best track performance, always
lubricate the track with water or snow before rotating the track.
2. Use an appropriate stand to securely support the rear of the
snowmobile at the rear bumper. The track should be about 4 inches
(10 cm) off the ground.
3. Start the engine and allow it to warm up two to three minutes.
4. Depress the throttle abruptly and allow the track to rotate several
revolutions.
TIP:It will take longer to warm up the track sufficiently during colder outdoor
temperatures.
5. Release the throttle, apply the brakes, shut off the engine and lower
the snowmobile to the ground.
6. Grasp the skis by their front loops and move them from side to side
to loosen snow and ice.
Slide Rail and Track Cooling
NOTICE: Inadequate cooling and lubrication will lead to overheating of the slide
rail and track, resulting in premature wear and failure. Reduce speeds
and frequently drive into fresh snow to allow adequate cooling and
polishing of the slide rail and track surfaces. Avoid operating on ice,
hard-packed surfaces or roads.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Fuel
WARNING
Gasoline is highly flammable and explosive under certain conditions.
• Always exercise extreme caution whenever handling gasoline.
• Always refuel outdoors or in a well-ventilated area.
• Always turn off the engine before refueling.
• Do not overfill the tank. Do not fill the tank neck.
• Do not smoke or allow open flames or sparks in or near the area where
refueling is performed or where gasoline is stored.
• If gasoline spills on your skin or clothing, immediately wash it off with soap
and water and change clothing.
• Never start the engine or let it run in an enclosed area. Engine exhaust fumes
are poisonous and can cause loss of consciousness or death in a short time.
WARNING
The engine exhaust from this product contains chemicals known to cause can-
cer, birth defects or other reproductive harm. Operate this vehicle only outdoors
or in well-ventilated areas.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Fuel Recommendation
For peak performance, POLARIS recommends the use of 91 octane fuel
or higher. Although 87 octane fuel is usable, some engine performance
will be lost and fuel economy will decrease. Do not use lower than 87
octane fuel. Do not use fuel containing more than 10% ethanol. Never
use E85 fuel in your snowmobile.
NOTICE: Operating with obstructed fuel systems will result in serious engine
damage. Perform maintenance as recommended.
Prolonged exposure to petroleum based products may damage paint.
Always protect painted surfaces when handling fuel.
Fuel System Deicers
If you use non-ethanol fuel (sometimes labeled “non-oxygenated”),
POLARIS recommends the regular use of isopropyl-based fuel system
deicer. Add one to two ounces per gallon (8-16 ml per liter) of gasoline
to prevent damage resulting from fuel system icing. Never use deicers
or additives containing methanol. POLARIS recommends the use of
Carbon Clean. See page 137 for the part numbers of POLARIS
products.
If you use fuel with up to 10% ethanol (sometimes labeled
“oxygenated”) do not add deicers or additives that contain any form of
alcohol.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Oil
Low Oil Level
Always maintain the oil level between the “ADD” mark and the bottle
neck. Do not fill the bottle neck. See page 75 for oil recommendations.
1. Immediately stop the
engine if the low oil
indicator light comes on.
2. Open the left side panel.
See page 94.
Safe
Range
3. View the oil level in the
oil bottle.
4. Add oil as needed before
operating.
NOTICE: Operating the
snowmobile without
adequate engine
lubrication can result
in serious engine
ADD Mark
damage. Always
check the oil level
when refueling. Add oil as needed.
The oil bottle cap is vented to allow proper oil flow. See your POLARIS
dealer for recommended replacement parts.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Auxiliary Engine Stop Switch
Push the auxiliary engine
stop switch down to ground
out the ignition and stop the
engine quickly. Pull the
Stop Switch
switch up to the RUN
position to allow restarting.
Throttle Release Switch
The throttle release switch is designed to stop the engine if all pressure
is removed from the throttle lever and the throttle cable or throttle plates
do not return to the normal closed position.
WARNING! Operating the snowmobile with a faulty throttle release switch can
result in serious injury or death in the event of an accident. If the throttle release
switch does not shut off the engine during a throttle system malfunction,
immediately push down the auxiliary engine stop switch. Do not start the engine
again until the malfunction has been corrected by your dealer.
Test the throttle release switch system daily before operation.
1. Sit on the seat.
Step 3
2. Start the engine and allow
it to idle.
3. Press and hold the lever
pivot as shown.
4. While preventing the lever
from pivoting, slightly
push the throttle lever as
shown. A properly
functioning switch must
shut down the engine.
Step 4
81
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Throttle Lever
WARNING! An improperly functioning throttle lever may cause erratic
snowmobile behavior and loss of control, which could result in serious injury or
death. If the throttle lever does not work properly, DO NOT start the engine.
If the engine stops abruptly when the throttle lever is released:
1. Turn the ignition switch to OFF.
2. Visually inspect the throttle cable and throttle body to determine
what caused the throttle release switch to activate.
3. Test the throttle lever by compressing and releasing it several times.
The lever and cable must return to the idle position quickly and
completely.
4. If the throttle lever operates properly, turn the ignition switch on and
go through normal starting procedures.
5. If the engine doesn’t start, take the snowmobile to an authorized
POLARIS dealer for service.
Throttle Lever Freeplay Inspection
Throttle lever freeplay is the gap created between the throttle lever and
throttle block, as you push the throttle lever, prior to the throttle cable
opening the throttle body plates. Excessive freeplay in the throttle cable
may cause the throttle release switch to activate, potentially stalling the
engine or preventing the engine from starting.
To inspect throttle lever freeplay,
follow these steps:
1. Stop the engine.
2. Slightly push the throttle lever
until you feel the cable tension
increase (throttle plates
opening).
3. Insert the blade of a feeler
gauge between the throttle
lever and throttle block. The
gap must be .009-.029 in.
(0.25-0.76 mm).
Gap
.009-.029 in.
(0.25-0.76 mm)
4. Adjust freeplay if the gap does not meet specification. See page 83.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Throttle Lever
Throttle Lever Freeplay Adjustment
Adjust throttle lever freeplay using the in-line throttle cable adjuster.
Lock
Nut
In-Line
Adjuster
1. Locate the in-line adjuster on the throttle cable.
2. Loosen the lock nut.
3. Rotate the adjuster clockwise to DECREASE freeplay. Rotate the
adjuster counter-clockwise to INCREASE freeplay.
4. When freeplay is adjusted to .009-.029 in. (0.25-0.76 mm), tighten
the lock nut against the adjuster.
5. Start the engine and allow it to idle.
6. Turn the handlebar to the full left and full right positions. Verify that
engine RPM does not increase as the handlebar is turned. If engine
RPM increases, the throttle lever freeplay is too tight and must be
readjusted.
WARNING! Do not operate the snowmobile if throttle cable freeplay is too tight.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
POLARIS Electronic Reverse Control (PERC)
WARNING
Improper reverse operation, even at low speeds, may cause loss of control,
resulting in serious injury or death. Damage will occur to the chaincase if shifting
is attempted when the engine is operating above idle speed.
• Shift to or from reverse only when the snowmobile is stopped and when
engine speed is at idle.
• Look behind the vehicle before and while backing.
• Avoid sharp turns.
• Apply throttle slowly.
Electronic reverse will activate only if the engine RPM is below 4000.
NOTICE: Engaging the starter when the engine is running WILL result in serious
engine damage, especially if the snowmobile is in reverse. Never
engage the starter when the engine is running.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
POLARIS Electronic Reverse (PERC)
Engaging Reverse
1. Stop the snowmobile and leave the engine idling.
2. Make sure the area behind your vehicle is clear.
3. Push the yellow reverse button on the left-hand control for one
second, then release. The engine will automatically reduce RPM
and start a reverse rotation. A flashing reverse light on the
instrument panel will indicate that the snowmobile is in reverse.
4. Apply the throttle slowly to make sure the snowmobile is in
reverse.The maximum engine RPM will be 6000 when in reverse.
TIP:If the engine stops running, the snowmobile will be in forward gear when it's
restarted.
Disengaging Reverse
1. Stop the snowmobile and leave the engine idling.
NOTICE: Engaging the starter when the engine is running WILL result in serious
engine damage, especially if the snowmobile is in reverse. Never
engage the starter when the engine is running.
2. Push the yellow reverse button for one second and release. The
engine will slow and begin to rotate forward. The light on the
instrument panel will shut off.
3. Apply the throttle slowly to make sure the snowmobile is in
forward.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Daily Storage
At the end of each ride, park the snowmobile on a level surface and
support it at the rear with an appropriate track stand. The track should be
suspended approximately 4 inches (10 cm) off the ground.
Remove the key and cover the snowmobile.
Towing
For your safety, do not attempt to use a tow hitch until you've read the
following warnings and understand the proper hitch functions.
WARNING! Objects towed with a rope have no braking power and can easily
collide with the rear of the snowmobile or other objects, resulting in serious
injury or death. DO NOT tow toboggans, sleds, saucers, or any type of vehicle
with a rope. Only a stiff metal pole connecting the towed object and the tow hitch
on the snowmobile should be used. If passengers are to be towed on a
toboggan or sled, make sure the pole is at least four feet (1.2 meters) long to
prevent any possibility of contact between the snowmobile's track and a person
riding in the towed object.
WARNING! Braking distances increase when towing loads. Slow down to
maintain control of the snowmobile.
If the snowmobile becomes inoperable and must be towed, and if it isn't
possible to use a rigid tow bar, attach the tow rope to the ski spindles
(not to the ski loops) to prevent damage to the steering components.
Remove the drive belt before towing, and have someone ride on the
towed snowmobile to operate the brake and steering when necessary.
NOTICE: Towing a disabled snowmobile with the drive belt in place can result in
serious damage to the engine and drive system. Always remove the
drive belt from a disabled snowmobile before towing.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Emission Control Information
Any qualified repair shop or qualified person may maintain, replace, or
repair the emission control devices or systems on your snowmobile.
Emission Control Label
Your snowmobile is equipped at the time of sale with an emission
control information (ECI) label and a factory-installed emissions
information hangtag. These items are required by U.S. Environmental
Protection Agency regulations. The ECI label is permanently affixed to
either the right side of the tunnel or the engine recoil cover. The ECI
label should not be removed, even after you purchase the snowmobile.
You may remove the factory-installed emissions information hangtag,
which is intended solely for your use in making a purchasing decision.
Emission Control Maintenance Requirements
Your snowmobile is certified to operate on gasoline with a minimum
octane level of 87 (R+M)/2. If your snowmobile is equipped with a
check engine light and it comes on, you must take your snowmobile to a
qualified dealer for diagnostic service. Specifications and adjustments
for engine tune-ups are located in the Service Manual, which is
available to your qualified service technician. Reverse (if equipped)
must not be engaged during engine tune-ups.
Owner's Responsibilities
Please read the Snowmobile Engine Emissions Limited Warranty, and
read the maintenance section of your owner's manual. You are
responsible for ensuring that the specified maintenance is performed.
POLARIS recommends that you contact an authorized POLARIS dealer
to perform any service that may be necessary.
Non-ionizing Radiation
This vehicle emits some electromagnetic energy. People with active or
non-active implantable medical devices (such as heart monitoring or
controlling devices) should review the limitations of their device and the
applicable electromagnetic standards and directives that apply to this
vehicle.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
POLARIS Recommended Maintenance Program
To ensure many trouble-free miles of snowmobiling enjoyment, follow
recommended regular maintenance and perform service checks as
outlined in this manual. Record maintenance and service in the
Maintenance Log beginning on page 171.
The recommended maintenance schedule on your snowmobile calls for
service and maintenance inspections at 150 miles (240 km), 500 miles
(800 km) and 1000 miles (1600 km). These inspections should be
performed by a qualified service technician. For continued optimum
performance and component life, continue maintenance checks at 1000
mile (1600 km) intervals.
All necessary replacement parts and labor incurred, with the exception
of authorized warranty repairs, become the responsibility of the
registered owner. If, during the course of the warranty period, part
failures occur as a result of owner neglect in performing recommended
regular maintenance, the cost of repairs are the responsibility of the
owner.
Personal safety is critical when attempting to service or make
adjustments to your snowmobile. If you're not familiar with safe service
or adjustment procedures and the use of tools, or if you don't feel
comfortable performing these tasks yourself, contact an authorized
POLARIS dealer for service.
NOTICE: Hot components can cause damage to plastic. Always make sure the
exhaust system and engine have cooled before tipping the snowmo-
bile on its side for service or inspection.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Periodic Maintenance Interval Table
The following chart is a guide based on average riding conditions. You
may need to increase frequency based on riding conditions. When
inspection reveals the need for replacement parts, always use genuine
POLARIS parts, available from your POLARIS dealer.
Item
See
Page
Frequency
150 mi.
500 mi.
1000 mi.
2000 mi.
Pre-
(240 km) (800 km) (1600 km) (3200 km)
Season
CLUTCH
Clutch Alignment Offset
(without belt)
114
I
I
I
Drive Belt Condition
Clutches
115
114
--
I
I
C
I
I
C
I
I
C
Belt Tension
I
I
I
Clutch Sheaves
114
I
I
I
ENGINE/COOLING
Engine Mounts
Recoil Rope
--
--
--
I
I
I
I
I
I
I
I
VES System
(600 Engine Only)
C
Coolant Level
Coolant Hose
Coolant Circulation
Coolant Leaks
Spark Plugs
105
--
I
I
I
I
I
I
I
I
I
I
R
I
I
I
--
I
--
I
I
I
I
I
104
108
108
R
I
Exhaust Pipe
Exhaust Retaining
Springs
I
I
I
I - Inspect (clean, adjust, tighten, lubricate, replace if necessary)
C - Clean R - Replace L - Lubricate
89
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Periodic Maintenance Interval Table
Item
See
Page
Frequency
150 mi.
500 mi.
1000 mi.
2000 mi.
Pre-
(240 km) (800 km) (1600 km) (3200 km)
Season
BRAKES
Hose Routing
Hose Condition
Fluid Leaks
--
--
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
--
Brake Pads
110
--
Brake Disc
Parking Brakes
Brake System
70
69
110
Brake Fluid
111
I
FUEL MANAGEMENT
Throttle Lever
Fuel Lines
Oil Lines
82
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
101
Air Box
--
I
I
ELECTRICAL
Auxiliary Shut-Off
Switch
72
I
I
I
I
I
Throttle Release Switch
Ignition Switch
Taillight
81
--
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
72
72
72
Brake Light
Headlight
I - Inspect (clean, adjust, tighten, lubricate, replace if necessary)
C - Clean
R - Replace
L - Lubricate
90
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Periodic Maintenance Interval Table
Item
See
Page
Frequency
1000 mi.
150 mi.
500 mi.
2000 mi.
Pre-
(240 km) (800 km) (1600 km) (3200 km)
Season
CHASSIS
Ski Toe Alignment
--
--
I
I
I
I
I
I
Suspension Mounting
Bolts
I
I
Bolt Torques
I
I
I
I
I
I
I
C
I
Steering Fasteners
--
--
I
I
I
I
Rear Suspension
Fasteners
Suspension Shock Oil
Rear Shock Threads
Skags (Wear Bars)
--
98
R
L
I
125
--
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Ski Saddle/Spindle Bolts
Drive Chain Tension
I
109
94
I
Hood and Side Panel
Fasteners
I
Rear Wheel Idler Bolts
Idler Bolt Jam Nut
Handlebar Centering
Tether Switch and Strap
Track Tension
121
121
--
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
72
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
120
122
--
Track Alignment
Front Limiter Strap
Rail Slide Condition
Chaincase Oil
128
98
I
R
I
R
I - Inspect (clean, adjust, tighten, lubricate, replace if necessary)
C - Clean R - Replace L - Lubricate
91
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Diagnostic Display Code Definitions
Open Load: There is a break in the wires that lead to the item listed in
the chart (injector, fuel pump, etc.), or the item has failed.
Short-to-Ground: The wire is shorted to ground between the electronic
control unit and the item listed in the chart.
Shorted Load: The wires leading to the item listed in the chart are
shorted together, or the item has shorted internally.
Short-to-Battery: The wire leading from the item listed in the chart to
the electronic control unit is shorted to a wire at battery voltage.
Diagnostic Codes
Component
Throttle Position Sensor
Condition
Voltage Too High
SPN
51
FMI
3
Voltage Too Low
4
Abnormal Rate of Change
Data Erratic, Intermittent or Missing
Voltage Too High
10
2
3
Vehicle Speed Sensor
Intake Air Temperature Sensor
84
105
Voltage Too Low
4
Barometric Pressure Sensor
Engine Temperature Sensor
Voltage Too High
Voltage Too Low
Voltage Too High
108
110
3
4
3
Voltage Too Low
4
Temperature Too High
Engine Overheat Shutdown
Temperature Above Normal Range
Voltage Too High
Voltage Too Low
Voltage Too High
16
0
15
3
4
3
Alternator Power Supply
167
173
Potential (DC Chassis Voltage)
Exhaust Temperature Sensor
Voltage Too Low
4
ECU Memory
Injector 1 (MAG
Checksum/CRC Error
Driver Circuit Open/Grounded
Driver Circuit Short to B+
Driver Circuit Open/Grounded
Driver Circuit Short to B+
Voltage Too Low
628
651
13
5
3
5
3
Injector 2 (PTO)
652
Knock Sensor 1
731
4
Ignition Coil Primary Driver 1
(MAG)
Driver Circuit Open/Grounded
1268
5
Fuel Pump Driver Circuit
Driver Circuit Open/Grounded
1347
5
92
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Diagnostic Display Code Definitions
Diagnostic Codes
Component
Knock Level Cylinder 1 (MAG)
Condition
Maximum Detonation Correction
Limit Reached
SPN
1352
FMI
0
Knock Above Critical Level
Maximum Detonation Correction
Limit Reached
16
0
Knock Level Cylinder 2 (PTO)
1353
Knock Above Critical Level
Voltage Too Low
16
4
Sensor Supply Voltage 1
3509
3510
3598
(TPS/TMAP Sensor Power)
Sensor Supply Voltage 2
(Ground Speed Sensor)
ECU Output Supply Voltage 2
(Injection Supply PWR)
Voltage Too Low
4
Voltage Too High
Voltage Too Low
3
4
Throttle Release Signal
Chassis Relay
Voltage Too High
Voltage Too Low
Throttle Stuck
Driver Circuit Open/Grounded
Driver Circuit Short to B+
Driver Circuit Grounded
Driver Circuit Short to B+
Voltage Too High
520194
3
4
7
5
3
5
3
3
520208
520215
520324
Exhaust Valve Solenoid
(600 Only)
EV Actuator Driver (Controller)
(800 H.O. Only)
Voltage Too Low
4
Learn Failure
Hardware Failure
Commanded Pos. Not Achieved
PWM Set Missing
13
12
7
2
MAX Temperature Exceeded
Signal Out of Range - Valve Open
Signal Out of Range - Valve Mid
520334 31
520325 31
520326 31
Signal Out of Range - Valve Closed 520327 31
Short to Battery Voltage
Short to Ground
520335
3
4
Abnormal Transition
Driver Circuit Open / Grounded
Driver Circuit Grounded
Out of Calibration
10
4
5
Electronic Oil Pump
3589
Oil Pump or Fuel Injector
Settings not Programmed
520241 13
93
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Hood and Side Panels
The hood and side panels protect the operator from moving parts. Never
operate a snowmobile with the side panels open or removed. Always
ensure that the hood and side panels are installed and securely latched
before starting the engine.
Side Panels (Opening/Removing)
To open a side panel, rotate the
two 1/4-turn fasteners at the
upper edges of the side panel.
Release the strap at the lower
edge of the side panel.
Opening
1/4-Turn
Fasteners
Strap
To remove a side panel, open the
side panel, then pull the panel
outward to release the tabs at the
lower edge of the panel. Lift the
side panel away from the
snowmobile.
Removing
94
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Hood Removal and Installation
1. Remove the side panels.
1/4-Turn
Fastener
2. Rotate the 1/4-turn fasteners
at the upper corners of the
hood.
3. Disconnect the wire harness
leading to the console
electronics.
4. Remove the hood assembly.
5. To reinstall the hood, slide
the nose clips into the
nosepan.
Wire Harness
6. Position the hood and align
the 1/4-turn fasteners at the
back of the hood. Secure the
fasteners.
7. Reconnect the wire harness.
8. Reinstall the side panels.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Tools
An L-wrench and a tool kit (containing a spare belt, spark plug wrench
and provisions for two spare spark plugs) are provided with the
snowmobile. Open the left side panel to access the tools.
The L-wrench is used to open
and close the driven clutch
when working with the drive
belt. The L-wrench, when
L-Wrench
properly engaged in the bracket,
secures the fender to the
console. To retrieve the L-
wrench, rotate it counter-
clockwise and slide it upward
from the bracket. When it’s not
in use, return the L-wrench to
the bracket and rotate it clockwise.
The tool kit is stored in a
container attached to the left
tube of the front bumper. Use
the following procedure to
remove the spare belt container
from the snowmobile.
1. Rotate the spark plug
wrench counter-clockwise
to release it from the
bracket.
2. Pull the wrench upward to
remove it.
Spark Plug Wrench
NOTE: The wrench secures the
container to the bumper.
3. Tilt the tool kit container
until the bracket detaches
from the bumper tube.
Step 3
96
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Tools
4. Pull the container out of the compartment.
5. When reinstalling the drive belt into the container, fold the belt as
shown. Verify that the belt loop at the rear of the container is
positioned slightly higher than the front loop.
Front
Rear
Step 4
Step 5
6. Slide the container into the
engine compartment at an
angle.
7. Position the container
bracket onto the bumper
tube and rotate it downward.
8. Reinstall the spark plug
wrench into the bracket and
through the hole in the
bumper tube.
Step 6
9. Rotate the spark plug
wrench clockwise until it
locks into place.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Rear Shock Body
Lubricate rear shock body threads
seasonally with a low-temperature
synthetic grease.
Driveshaft Bearing
This model has sealed bearings that
require no additional lubrication.
Threads
Chaincase Oil
Check and change the chaincase oil at the intervals outlined in the
Periodic Maintenance Table beginning on page 88. Maintain the oil
level at the top of the fill plug hole. POLARIS recommends the use of
Synthetic Chaincase Lubricant. See page 137 for the part numbers of
POLARIS products.
Oil Level Check
1. Position the snowmobile on
a level surface.
2. Remove the fill plug.
3. Using a funnel, slowly add
the recommended oil until
the fluid begins to overflow.
4. Clean the area with a clean,
dry shop towel.
5. Reinstall the fill plug.
Torque: 6-10 ft-lbs (8-13 Nm)
Fill Plug
98
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Chaincase Oil
Oil Change (Pump Method)
NOTE: This procedure requires the use of a commercially available hand
pump oil extractor.
1. Elevate the front of the snowmobile using a floor jack or appropriate
lift.
2. Remove the fill plug. Clean all
metal shavings off the plug.
3. Insert the tube of a hand pump
oil extractor into the fill hole.
Direct the hose toward the
bottom front area of the cover,
away from the chain/sprocket.
4. Extract the oil from the
chaincase.
5. Lower the snowmobile.
6. Using a funnel, slowly add the recommended oil until the fluid
begins to overflow. Maximum fluid capacity is 10.5 oz. (310 ml).
7. Clean the area with a clean, dry shop towel.
8. Reinstall the fill plug.
Torque: 6-10 ft-lbs (8-13 Nm).
99
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Chaincase Oil
Oil Change (Cover Drain Method)
1. Position the snowmobile on a
level surface.
Fender Screws
2. Remove the two screws
securing the fender to the
chaincase.
3. Remove the right side panel.
If equipped with a battery,
remove the battery and
bracket.
Step 2
NOTICE: When removing the battery,
disconnect the BLACK (-)
cable first, and then
disconnect the RED (+)
cable last.
4. Place a drain pan under the
chaincase.
5. Loosen (do not remove) the
chaincase cover screws.
6. Carefully pry the cover open.
Step 5
Chaincase Cover
Screws
NOTICE: DO NOT insert a
screwdriver or pry bar
between the cover and
chaincase. Seal damage
may occur.
7. Allow the oil to drain
completely.
8. Tighten the cover screws.
Torque: 6-10 ft-lbs (8-13 Nm)
Step 6
Fill Plug
9. Remove the fill plug. Clean all
metal shavings off the plug.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Chaincase Oil
Oil Change (Cover Drain Method)
10. Using a funnel, slowly add the recommended oil until the fluid
begins to overflow. Maximum fluid capacity is 10.5 oz. (310 ml).
11. Clean the area with a clean, dry shop towel.
12. Reinstall the fill plug.
Torque: 6-10 ft-lbs (8-13 Nm)
13. Reinstall the screws securing the fender to the chaincase.
Fuel Filter / Fuel Lines
This snowmobile is not equipped with an in-line fuel filter. The fuel
pump uses a sock-type pickup filter located within the fuel tank. This
filter should only require maintenance if debris or foreign material
enters the fuel tank. See your POLARIS dealer for service.
Contaminated or poor quality fuel may shorten the life of fuel system
components and result in poor engine performance. Always store fuel in
clean fuel containers. If low fuel pressure or reduced engine
performance occurs between the recommended fuel filter service
intervals, the filter may need replacement. Please see your dealer.
Inspect the fuel lines regularly for signs of deterioration or damage.
Always check fuel line condition after periods of storage. Normal
deterioration from weather and fuel compounds may occur. Replace
worn or damaged fuel lines promptly.
NOTICE: Kinking the fuel lines or using a pliers or similar tools to remove fuel
lines may cause damage to the lines. If a fuel line has been damaged
or kinked, replace it promptly.
Fuel Pump
All fuel pump service must be performed by an authorized POLARIS
dealer. Do not attempt to service the fuel pump.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Intake Filters
The intake foam filters
limit snow ingestion into
the intake system. When
operating in loose
powder snow, check the
foam filters periodically
to remove any
accumulation of snow.
Foam Filters
102
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Spark Plugs
Spark Plug Recommendations
A new engine can cause
temporary spark plug
fouling due to the
Spark Plugs
preservative added during
the assembly process. Avoid
prolonged idle speeds,
which cause plug fouling
and carbonization.
Change the spark plugs at
the intervals outlined in the
Periodic Maintenance Table
beginning on page 88.
• Use the recommended spark plugs with the proper gap. Refer to the
specifications section beginning on page 142.
• Use only resistor-type spark plugs.
• Torque spark plugs to 18-22 ft-lbs (24-30 Nm).
• Always carry spare spark plugs.
NOTICE: Using non-recommended spark plugs can result in serious engine
damage. A spark plug with a heat range too high will always cause
engine damage if the engine is operated in conditions more severe
than intended for that plug.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Spark Plugs
Spark Plug Inspection
Spark plug condition is indicative of engine operation. The spark plug
firing end condition should be read after the engine has been warmed up
and the vehicle has been driven at higher speeds. Immediately check the
spark plug for correct color.
CAUTION! A hot exhaust system and engine can cause burns. Wear
protective gloves when removing a spark plug for inspection.
1. Remove the side panels and the hood.
2. Remove the spark plug cap.
3. Using the spark plug wrench provided in the tool kit, rotate the
spark plug counter-clockwise to remove it.
4. Reverse the procedure for spark plug installation. Torque to
specification.
5. Reinstall the spark plug cap. Verify and “audible” click is heard
when installing the plug cap.
Spark Plug Condition
Normal Plug
The normal insulator tip is gray, tan or light brown. There will be few
combustion deposits. The electrodes are not burned or eroded. This
indicates the proper type and heat range for the engine and the service.
Wet Fouled Plug
The wet fouled insulator tip is black. A damp oil film covers the firing
end. There may be a carbon layer over the entire nose. Generally, the
electrodes are not worn. General causes of fouling are excessive oil or
use of non-recommended injection oil.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cooling System
Coolant
The coolant supplied in the system at the factory is a 50/50 mixture of
ethylene-glycol and distilled water, which will provide adequate freeze
protection under most conditions. If the vehicle will be stored or
operated at extremely low temperatures, greater protection may be
required. Please see your POLARIS dealer.
POLARIS recommends the use of POLARIS Antifreeze 50/50 Premix.
This antifreeze is already premixed and ready to use. Do not dilute with
water. See page 137 for the part numbers of POLARIS products.
Never add tap water to the cooling system. Minerals cause deposits and
may react adversely with the metals in the engine and cooling system.
Coolant Level
The engine coolant level is
controlled by the recovery system.
The recovery system components
are:
• Coolant bottle/overflow tank
• Pressure cap
• Connecting hoses
Always maintain the coolant level
at or slightly above the FULL
COLD mark on the coolant bottle
FULL
(when the engine is cold).
COLD
Mark
1. Stop the engine.
2. Open the right side panel.
3. View the coolant level in the
coolant bottle.
4. Add coolant as needed.
NOTICE: Operating the snowmobile with insufficient coolant will result in
overheating and serious engine damage. Always maintain the coolant
level as recommended.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cooling System
Flushing the Cooling System
To ensure that the coolant maintains its ability to protect the engine,
drain the system completely every five (5) years and add a fresh mixture
of antifreeze and distilled water. This service must be performed when
the engine is cold. Ask your POLARIS dealer to check the coolant when
he performs the fall tune-up on your snowmobile.
Bleeding the Cooling System
CAUTION! Steam and hot liquids will cause burns to your skin. Never bleed the
cooling system or remove the pressure cap when the engine is warm or hot.
Use of a non-standard pressure cap will not allow the recovery system to
function properly. If the pressure cap needs replacement, contact your
dealer for the correct part.
NOTICE: Severe engine damage may occur if the cooling system becomes
restricted or plugged or contains trapped air pockets.
Perform this procedure in a well-ventilated area. Use the recommended
coolant. See page 105.
1. Open the side panels and remove the hood.
2. Close the side panels.
WARNING! Never operate a snowmobile with the side panels open or removed.
3. Position the snowmobile with the right ski and control arms
elevated at a 45-degree angle.
4. Fill the coolant bottle to the
COLD FILL mark.
5. Using an 8 mm wrench,
loosen the air bleed screw
located on the top of the
coolant outlet elbow. Use a
shop towel to catch any
coolant that leaks from the
bleeder. Tighten the screw
after a steady stream of
Bleed Screw
coolant flows from the
bleeder.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cooling System
Bleeding the Cooling System
6. Fill the coolant bottle to the COLD FILL mark.
7. Install the coolant bottle cap to the first lock. Do not tighten to the
fully seated position.
8. Lock the parking brake.
9. Start the engine and allow it to run at a fast idle for several minutes,
until the heaters are warm to the touch. Loosen the bleed screw
occasionally to purge any trapped air.
10. When all heater extrusions are warm to the touch, stop the engine.
11. Allow the engine and cooling system to cool. Secure the bleed
screw.
12. Fill the coolant bottle to the COLD FILL mark. Reinstall the bottle
cap securely.
13. Carefully lower the front end of the snowmobile.
14. Open the side panels and reinstall the hood. Close the side panels.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Exhaust System
Check the exhaust system for wear or damage at approximately 2,000
miles (3200 km). Always allow the engine and exhaust system to cool
completely before inspecting.
CAUTION! Hot exhaust system parts can cause burns. Allow adequate time for
the exhaust system to cool. Never perform this procedure with the engine
running.
1. Open the side panels and
remove the hood.
2. Inspect the muffler and
pipes for cracks or damage.
3. Check for weak or missing
retaining springs or damper/
support grommets.
4. Check for loose clamps on
the pipe covers.
5. Reinstall the hood and side
panels.
Springs
108
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Drive Chain Tension
Check drive chain tension at the intervals outlined in the Periodic
Maintenance Table beginning on page 88. Check again before each long
trip.
CAUTION! Hot exhaust system parts can cause burns. Allow adequate time for
the exhaust system to cool. Never perform this procedure with the engine
running.
1. Remove the side panels.
2. Rotate the driven clutch
counter-clockwise to move all
chain slack to the tensioner
side.
3. Lock the parking brake.
4. Loosen the adjuster bolt jam
nut.
5. Finger-tighten the adjuster
bolt until it can no longer be
adjusted by hand, then back
off 1/4 turn.
Jam Nut
Adjuster Bolt
6. Tighten the jam nut while holding the adjuster bolt.
Torque: 21 ft-lbs (28 Nm)
7. Reinstall the side panels.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Brakes
Hydraulic Brake Inspection
Inspect brake lever travel before each use of the snowmobile. See page
69.
Brake pads must be replaced when the brake pad material becomes
thinner than the backing plate (approximately 1/16 inch or 1.5 mm). A
kit is available for replacing brake pads. Please see your dealer.
WARNING! Brake failure during operation can result in serious injury or death.
Properly functioning brakes are vital to your safety. Be sure the brake pads do
not drag on the disc and that brake lever travel is not excessive. Always replace
brake pads when the brake pad material becomes thinner than the backing plate
(approximately 1/16 inch or 1.5 mm).
CAUTION! Hot exhaust system parts can cause burns. Allow adequate time for
the exhaust system to cool. Never perform this procedure with the engine
running.
Excessive Lever Travel
Hydraulic brakes are self-adjusting, but if excessive brake pad clearance
develops, bring the snowmobile to an authorized POLARIS dealer for
inspection and adjustment.
Brake Components
1. Brake Caliper
2. Brake Disc
3. Brake Pad Material -
Replace when thickness
is less than 1/16 inch
(1.5 mm).
110
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Brakes
Brake Fluid
Replace brake fluid at least every two years with POLARIS DOT 4 high
temperature brake fluid. See page 137 for the part numbers of POLARIS
products.
WARNING! After opening a bottle of brake fluid, always discard any unused
portion. Never store or use a partial bottle. Brake fluid is hygroscopic, meaning it
rapidly absorbs moisture from the air. The moisture causes the boiling
temperature of the brake fluid to drop, which can lead to early brake fade and
the possibility of accident or serious injury.
WARNING! Keep the master cylinder cover free of dirt and debris. The vent slits
allow for diaphragm movement, and if they become plugged, movement of
brake fluid below the diaphragm may be restricted, altering brake function.
NOTICE: Brake fluid will damage labels, paint and some plastics. Always wipe
up spills immediately.
Brake Fluid Level
Position the handlebars so
the brake fluid reservoir is as
close to level as possible.
View the fluid level through
8 mm MAX
10 mm MIN
the reservoir (shaded in
illustration). If the level is
below the MIN (minimum)
level specification, add
POLARIS DOT 4 brake
fluid.
Adding Brake Fluid
MAX
CAUTION! Do not allow dirt or water
to enter the brake reservoir.
MIN
1. Remove the reservoir cover and
diaphragm.
2. Add the recommended brake
fluid to the MAX level.
3. Reinstall the diaphragm.
4. Reinstall the cover and screws.
Torque: 11-13 in-lbs (1.2-1.4 Nm)
111
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Brakes
Bleeding the Hydraulic Brake System
Air in the hydraulic brake system will cause spongy brake lever action.
Bleed the system before operating the snowmobile.
WARNING! Operating the vehicle with a spongy brake lever can result in loss of
brakes, which could cause an accident and lead to serious injury or death.
Never operate the vehicle with a spongy-feeling brake lever.
CAUTION! Hot exhaust system parts can cause burns. Allow adequate time for
the exhaust system to cool. Never perform this procedure with the engine
running.
During the bleeding procedure, keep the brake handle as level as
possible. The reservoir must be in this position to minimize the
possibility of air entering the system through the reservoir vent.
1. Remove the brake master cylinder reservoir cover and gasket.
2. Fill the master cylinder reservoir to between the MIN and MAX
marks or 1/4-5/16 inch (.6-.8 cm) below the lip of the reservoir
opening. Reinstall the gasket and cover.
3. Slip a rubber tube over the ball of the bleeder valve and direct the
flow of fluid into an approved container.
4. Squeeze the brake lever a full stroke. Then unscrew the bleeder
valve 3/4-turn to release air.
5. Close the bleeder valve and release the brake lever.
6. Repeat steps 4 and 5 until fluid flows from the bleeder valve in a
solid stream free of air bubbles.
WARNING! Overfilling the master cylinder leaves no room for fluid expansion
and may cause the brakes to lock, resulting in serious injury or death. Always
add brake fluid to the fill line as recommended.
7. After bleeding is complete, refill the reservoir to the proper level.
See page 111.
8. Reinstall the gasket and cover.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Lights
The headlight and taillight assemblies feature LED elements and are not
serviceable. If an LED fails to illuminate in either the headlight or
taillight, the entire assembly must be replaced. Please see your
POLARIS dealer.
Headlight
Taillight
113
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Clutch System
Periodically inspect clutch
sheaves for damage, wear or belt
residue. To maintain optimum
performance, clean with non-oil
based cleaners such as isopropyl
alcohol.
WARNING! If you become aware of
higher than normal clutch
engagement or an unusual vibration
or shift pattern, see your dealer
immediately. Do not operate the
snowmobile until repairs have been
made.
All clutch maintenance and repairs must be performed by an authorized
POLARIS dealer. Any unauthorized modifications to clutches, such as
adding or removing weights, will void the warranty.
NOTICE: The bushings in the weights and rollers of POLARIS clutches are
made of a material that may be damaged if lubricated. Do not lubri-
cate clutch bushings.
Clutch Alignment Offset
Clutch alignment offset is important for maintaining optimum
performance. See your dealer for service and adjustments. A special tool
is required to check for proper alignment.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Clutch System
Drive Belt Condition
Periodically check the condition and tension of
the drive belt. Inspect the belt for signs of
excessive wear: frayed edges, missing cogs,
cracks and excessive looseness. Replace the
belt if any of these conditions exist. See Drive
Belt Troubleshooting on page 162.
Always carry a spare drive belt. Store the spare
belt in the belt holder as shown. When placing
the belt in the holder, orientate the belt to match
the profile of the hood.
For improved drive-away during extremely
cold temperatures, remove the belt and warm it
to room temperature. Reinstall it before starting
the snowmobile.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Clutch System
Drive Belt Deflection
1
2
Measure belt deflection
with both clutches at rest
and in their full neutral
position.
Place a straight edge (1) on
the belt and apply
downward pressure while
measuring at point 2. This
measurement should be 1
1/4 inches (3.2 cm).
Drive Belt Deflection Adjustment
1. Loosen the 11 mm jam nut
Increase
Decrease
on the belt width adjuster.
2. Using a 3 mm Allen
wrench, turn the set screw
inward (clockwise) to
increase the distance
between the sheaves or
outward (counter-
clockwise) to decrease the
distance.
3. Tighten the jam nut.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Clutch System
Drive Belt Removal
NOTICE: Do not attempt to remove the drive belt after operating in reverse. The
snowmobile must be stopped after forward motion to prevent damage
to components during belt removal. Rotate the driven clutch counter-
clockwise 1/4 turn by hand to ensure forward engagement before
attempting to remove the belt.
1. Stop the engine after
operating in a forward
motion.
2. Turn the ignition key off.
Wait for the engine to
come to a complete stop.
3. Lock the parking brake.
4. Remove the left side
panel.
5. Rotate the driven clutch
counter-clockwise 1/4
Step 7
turn by hand to ensure
forward engagement.
6. Retrieve the L-wrench.
See page 96. Install the
wrench into the open
threaded hole in the outer
sheave of the clutch.
7. Turn the wrench
clockwise until the
sheaves open far enough
to remove the belt.
8. Firmly grasp the belt
midway between the
Step 8
clutches and pull upward
and rearward to remove
it.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Clutch System
Drive Belt Installation
1. Verify the driven clutch sheaves are open. If they are not, install the
L-wrench and open the sheaves.
NOTE: When installing the belt, verify POLARIS or the part number can be
read from the outside of the snowmobile.
2. Drop the drive belt over the drive clutch and pull back the slack.
The belt cord line should be flush with, or slightly above, the outer
circumference of the driven clutch sheaves.
3. Hold the belt down between
the sheaves and roll the
bottom portion over the
outer clutch sheave. Work
the belt to the outer edge of
the sheave.
4. Turn the L-wrench counter-
clockwise to tighten the
sheaves. Work the belt
around the clutches as you
Step 4
remove the L-wrench.
Doing so will set the belt in
“low gear”.
5. Reinstall the wrench to the
wrench bracket to secure the
fender to the console.
6. Reinstall the side panel.
7. Break in the new belt. See
page 76.
Step 5
118
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Track Maintenance
Track Inspection
WARNING! Broken track rods can cause a rotating track to come off the
snowmobile, which could cause serious injury or death. Never operate with a
damaged track. Never rotate a damaged track under power.
1. Using a hoist, safely lift
and support the rear of
the snowmobile off the
ground.
2. Rotate the track by hand
to check for damage.
3. Carefully examine the
track along the entire
length of each rod. Bend
the track to check for
breakage.
Inspect
4. Replace the track if any
rod damage is found.
Track Lubrication
The slide rail needs snow
for lubrication. Excessive
wear indicates insufficient
lubrication. A new rail
slide can cause faster heat
build-up in limited
lubrication, resulting in
excessive wear.
Slide Rail
WARNING! Operating with insufficient lubrication between the rail slide and
track guide clips can cause track failure, loss of vehicle control and loss of
braking ability, which can result in serious injury or death. Avoid operating for
extended periods on ice and other surfaces that have little or no snow for
lubrication.
If excessive rail slide wear occurs due to poor snow conditions,
additional wheel kits may be available. See your dealer for more
information.
Track damage or failure caused by operation on ice or under other poor
lubrication conditions will void the track warranty.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Track Maintenance
WARNING! Moving parts can cut and crush body parts. When performing the
checks and adjustments recommended on the following pages, stay clear of all
moving parts. Never perform track measurement or adjustments with the engine
running.
Track Tension
Track adjustment is critical for proper handling. Always maintain
correct tension and alignment.
TRACK TENSION DATA CHART
Slack Measurement
Measurement
Suspension
(Preferred -
Maximum)
Weight
Location
RUSH 120
16 inches (40 cm)
ahead of rear
idler shaft
1 - 1-1/4 in.
(2.54 - 3.175 cm)
10 lbs.
(4.54 kg)
SWITCHBACK
137
NOTE: If the track is studded, POLARIS recommends maintaining one (1)
inch (2.54 cm) track tension setting at all times.
1. Verify the track is warmed up and limber. Stop the engine.
NOTICE: Do not use the rear bumper to lift the rear of the snowmobile for track
adjustments.
2. Lift the rear of the snowmobile by the chassis (seat support, x-brace
or running boards) until the track is slightly above the ground.
Safely support the rear of the snowmobile in this position.
3. Place the recommended weight or downward pressure on the track
at the specified distance (see chart) ahead of the center of the rear
idler wheel.
4. Measure at the point where the weight is hanging.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Track Maintenance
Track Tension
5. Check for specified slack between the wear surface of the track clip
and the plastic slider. Refer to the Track Tension Data Chart on page
120.
If the track needs adjustment:
6. Loosen the rear idler shaft bolt.
7. Loosen the locknuts.
Track Adjusting
Slack Measurement
Screw
Lock Nut
Idler
Shaft
Bolt
Track
10 lbs. (4.54 kg)
16 inches
(40 cm)
8. Tighten or loosen the track adjusting screws to provide equal
adjustment on both sides of the track.
9. Repeat the measurement on the other side of the track.
TIP:Check more frequently when the snowmobile is new or if studs are
installed.
10. Remove the weight. Start the engine and slowly rotate the track at
least five revolutions. Let the track come to a stop (do not apply
brakes).
11. Check track alignment (see page 122) and adjust as necessary.
12. Tighten the locknuts.
13. Tighten idler shaft bolts to 35 ft-lbs (47.5 Nm).
121
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Track Maintenance
Track Alignment
Periodically check that the track is centered and running evenly on the
slide rails. Misalignment will cause excessive wear to the track and slide
rail.
1. Safely support the rear of the snowmobile with the track off the
ground.
2. Start the engine and apply a small amount of throttle until the track
turns slowly at least five complete revolutions. Stop the engine and
let the track come to a stop (do not apply brakes).
3. Inspect track alignment by
looking through the track
window to make sure the
rails are evenly spaced on
each side. If the track runs
to the left, loosen the idler
shaft bolts, then loosen the
left locknut and tighten the
left adjusting bolt. If the
track runs to the right,
loosen the idler shaft bolts,
then loosen the right
Rails
locknut and tighten the
right adjusting bolt.
4. After adjustments are complete, tighten the locknuts.
5. Tighten the idler shaft bolts.
Torque: 35 ft-lbs (47.5 Nm)
6. Repeat steps 2 and 3 to verify proper alignment.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Steering System
Front Suspension Inspection
WARNING! Improper fastener torque or front suspension component damage
may cause loss of steering control, resulting in serious injury or death. See your
POLARIS dealer.
Each week, or before a long ride, check the following items. If
component damage or loose fasteners are found, see your POLARIS
dealer for service.
• Upper / Lower control arms
• Spindles
• Fasteners (X in illustration)
• Skis, ski loops, ski stops, skags/carbides
• Tie rods, rod ends, tie rod boots
• Sway bar / sway bar linkage
X
X
X
123
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Steering System
Ski Alignment
WARNING! Improper ski alignment or adjustment may cause loss of steering
control, resulting in serious injury or death. Do not attempt to change the ski
alignment or toe adjustment. See your POLARIS dealer.
If the steering feels heavy, or if the snowmobile seems to pull or dart to
the side, ski alignment may need adjustment. Refer to the service
manual or see your dealer for this service.
Ski Toe Settings
WARNING! Improper ski toe adjustment may cause loss of steering control,
resulting in serious injury or death. Do not attempt to change toe adjustment.
See your POLARIS dealer.
The skis on your snowmobile are set with a small amount of toe-out at
the factory. You can inspect the toe setting by following the procedure
below. If adjustments are required, refer to the service manual or see
your dealer for this service.
1. Place the handlebars in a straight-ahead position.
2. With only vehicle weight compressing the suspension, measure
10 inches (25.4 cm) forward from the center of the ski mounting
bolt. See illustration. At this point, measure between the skis. This is
measurement X.
3. Perform the same measurement rearward from the center of the ski
mounting bolt. This is measurement Y.
4. The X measurement should be 1/8-1/4 inch (3-6 mm) greater than
the Y measurement.
X
10 in.
(25.4 cm)
10 in.
(25.4 cm)
Y
124
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Steering System
Ski Skags
WARNING! Worn skis and/or skags will adversely affect handling. Loss of
vehicle control may result, causing serious injury or death. See your dealer's
studding chart for recommended skags. If you install longer or more aggressive
carbide skags than the original equipment, it may also be necessary to add track
studs to maintain proper vehicle control while turning on hard-packed snow or
ice.
Check skags before each use of
Inspect carbide for
the snowmobile to ensure
damage or wear
positive steering characteristics.
Skags must be replaced when
worn to half their original
diameter.
TIP:Carbide skags must be
replaced if any abnormal wear
or chipping is found.
Ski Skag Replacement
1. Raise and support the front of
the snowmobile so the skis are
approximately 6 inches (15.2
cm) from the ground.
2. Remove the attaching nuts and
pry the skag downward.
3. Remove the front end of the
skag.
Ski Skag
4. Remove the rear end of the
skag.
5. Reverse the steps to install a
skag. Tighten the nuts.
Torque: 7 ft-lbs (10 Nm)
125
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Front Suspension Control Arms
Control Arm Pivot Adjustment
The upper and lower control arms feature slotted pivots to allow for
adjustment to compensate for bushing wear.
NOTE: Upper control arm shown. Procedure is the same for lower control arm
adjustment.
1. Loosen the four lock nuts.
Loosen Nuts
2. From the bushing side of
each pivot, push the pivot
toward the control arm.
3. While holding the
pivot(s) in place, tighten
the lock nuts.
Torque: 30 ft-lbs (41 Nm)
126
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Rear Suspension
Rear Suspension Inspection
WARNING! Improper fastener torque or rear suspension component damage
may cause loss of vehicle control, resulting in serious injury or death. See your
POLARIS dealer.
Each week, or before a long ride, check the following items. If
component damage or loose fasteners are found, see your POLARIS
dealer for service.
• Rear crank / rear pivots
• Rear idler wheels / shaft
• Bogie / carrier wheels / shafts / fasteners
• Front torque arm
• Fasteners (X in illustration)
• Shocks
• Rail sliders
• Track
X
X
127
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Rear Suspension
Rail Slide Wear
Measure slide thickness at
several points along the rail.
Have your dealer replace the
slide when it's worn down to
the top of the wear limit
7/16 inch
(1.1 cm)
X
indicator groove. Do not
operate the snowmobile if
slide thickness measures less
than 7/16 inch (1.1 cm).
128
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Battery (if equipped)
WARNING! Improperly connecting or disconnecting battery cables can result in
an explosion and cause serious injury or death. When removing the battery,
always disconnect the negative (black) cable first. When reinstalling the battery,
always connect the negative (black) cable last.
Battery Removal
CAUTION! Hot exhaust system parts can cause burns. Allow adequate time for
the exhaust system to cool. Never perform this procedure with the engine
running.
1. Remove the right side panel.
2. Remove the two plastic
rivets (1) securing the
console panel to the chassis.
3. Remove the plastic rivet (2)
securing the fender to the
chassis.
4. Remove the rubber hold-
down strap (3).
5. Disconnect the black
(negative) battery cable first.
6. Disconnect the red (positive)
battery cable last.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Battery (if equipped)
Battery Removal
7. Remove the screw (4) securing
the battery shield to the
chassis.
8. Remove the battery shield (5).
9. Pull the fender away from the
battery compartment and
remove the battery.
10. With the battery removed
from the snowmobile, the
battery bracket can be
removed to access the
chaincase. Remove the two
nuts (6) and the screw (7)
that secure the bracket to the
chassis. Remove the bracket.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Battery (if equipped)
Battery Installation
When installing a new battery, make sure it’s fully charged prior to its
initial use. Using a new battery that has not been fully charged can
damage the battery and result in a shorter life. It can also hinder vehicle
performance. Follow the battery charging instructions on page 132
before installing the battery.
1. Ensure that the battery is fully charged.
2. If the battery bracket was removed, reinstall the bracket.
3. Tighten the nuts.
Torque: 7 ft-lbs (10 Nm)
4. Tighten the screw.
Torque: 22 ft-lbs (30 Nm)
5. Place the battery in the battery holder.
6. Connect and tighten the red (positive) cable first.
7. Connect and tighten the black (negative) cable last.
8. Verify that cables are properly routed.
9. Install the battery shield. Tighten the shield screw.
Torque: 7 ft-lbs (10 Nm)
10. Install the right fender using the plastic rivet.
11. Reinstall the console using the two plastic rivets.
12. Reinstall the side panel.
Battery Storage
Whenever the vehicle is not used for a period of three months or more,
remove the battery from the vehicle, ensure that it's fully charged, and
store it out of the sun in a cool, dry place. Check battery voltage each
month during storage and recharge as needed to maintain a full charge.
TIP:Battery charge can be maintained by using a POLARIS Battery TenderTM
charger or by charging about once a month to make up for normal self-
discharge. Battery TenderTM can be left connected during the storage
period, and will automatically charge the battery if the voltage drops below a
pre-determined point.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Battery (if equipped)
Battery Charging
The following battery charging instructions apply only to the
installation of a sealed battery. Read all instructions before proceeding
with the installation of this battery.
The sealed battery is already filled with electrolyte and has been sealed
and fully charged at the factory. Do not ever pry the sealing strip off or
add any other fluid to this battery.
The single most important thing about maintaining a sealed battery is to
keep it fully charged. Since the battery is sealed and the sealing strip
cannot be removed, you must use a voltmeter or multimeter to measure
DC voltage.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Battery (if equipped)
Battery Charging
For a refresh charge, follow all instructions carefully.
1. Check the battery voltage with a voltmeter or multimeter. A fully
charged battery will register 12.8 V or higher.
2. If the voltage is less than 12.8 volts, recharge the battery at 1.2 amps
or less until the battery voltage is 12.8 or greater.
Tip: When using an automatic charger, refer to the charger manufacturer's
instructions for recharging. When using a constant current charger, use the
following guidelines for recharging.
WARNING! An overheated battery may explode, causing severe injury or
death. Always watch charging times carefully. Stop charging if the battery
becomes very warm to the touch. Allow it to cool before resuming charging.
Tip: Always verify battery condition before and 1-2 hours after the end of
charging.
Charge Time
State of
Charge
(Using constant current
Voltage
Action
charger @ standard amps
specified on top of battery)
100%
12.8-13.0 volts
None, check at 3
mos. from date of
manufacture
None required
75%-100%
12.5-12.8 volts
May need slight
charge, if no
3-6 hours
charge given,
check in 3 months
50%-75%
25%-50%
12.0-12.5 volts
11.5-12.0 volts
Needs charge
Needs charge
5-11 hours
At least 13 hours,
verify state of charge
0%-25%
11.5 volts or less Needs charge with
desulfating charger
At least 20 hours
133
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Fall Tune-Up
For maximum performance, arrange for a fall service tune-up with your
POLARIS dealer. His experienced and trained service technician will
keep your snowmobile in peak operating condition.
Matte Clear Coat Cleaning (if equipped)
Matte finish products are prone to trapping dirt, oils and other
contaminants. POLARIS Industries recommends cleaning with warm
water and a mild dish detergent. Use a soft sponge to gently rub the
surface and rinse with clean warm water. For stubborn stains such as
grease or oil use a citrus based cleaner (3M Citrus Base Cleaner
recommended). Spray onto the area to be cleaned and rub with a soft
sponge. Allow to sit for a couple of minutes and wash away with clean
warm water. Repeat as necessary to clean the surface.
NOTICE: Never use a polishing/buffing wax or any sponge that has an abrasive
surface. These products will buff the matte surface of the finish result-
ing in a glossy finish. It is not recommended that you clean matte fin-
ishes with a pressure washer as this will further imbed contaminants
into the clear coat and possibly damage the labels.
Extended Storage
Off-season or extended storage of your snowmobile requires preventive
measures to aid against deterioration and to prolong the useful life of
many components. See page 137 for the part numbers of POLARIS
products.
134
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cleaning and Preservation
Proper storage starts with cleaning, washing, and waxing the hood, side
panels, chassis, and plastic parts. Wipe down remaining surfaces with a
damp cloth. Clean and touch up with paint any rusted or previously
painted surfaces. Be sure that corrosive salt and acids are removed from
surfaces before beginning preservation with waxes and rust inhibitors
(grease, oil or paint).
The snowmobile should be stored in a dry garage or shed, out of direct
sunlight, and covered with a fabric snowmobile cover. Plastic tarp may
cause condensation to form and damage snowmobile components.
Battery Storage
Whenever the vehicle is not used for a period of three months or more,
remove the battery from the vehicle, ensure that it's fully charged, and
store it out of the sun in a cool, dry place. Check battery voltage each
month during storage and recharge as needed to maintain a full charge.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Extended Storage
Clutch and Drive System
Remove the drive belt and store in a cool dry location. Do not lubricate
clutch components, except the driven clutch shaft bushing as outlined in
the Master Repair Manual. See your dealer.
Engine Protection
Proper preparation of the engine and fuel system is vital to the
prevention of rust and corrosion on precision engine parts during
storage. Whenever the snowmobile is stored for a period of more than
60 days, the engine must be fogged with fogging oil. Follow the engine
fogging instructions provided on the container.
Always add Carbon Clean or a fuel conditioner/stabilizer to the fuel
tank. Follow the instructions on the container, running the engine for
five minutes to get additives through the entire fuel system. Top off with
fresh fuel. Do not allow the snowmobile to run out of fuel.
Electrical Connections
Replace worn or frayed electrical wire and connectors. Be sure wiring
harness is properly secured away from sharp edges, steering linkage,
moving parts, and hot exhaust parts.
Track and Suspension
Moderate track tension should be maintained during summer storage.
The snowmobile should be supported off the ground to allow the track
to hang freely.
Transporting the Snowmobile
Whenever the snowmobile is transported:
1. Be sure the fuel cap and oil cap are installed correctly.
2. Tie the snowmobile to the transporting unit securely using suitable
straps.
3. Remove the ignition key to prevent loss.
136
Download from Www.Somanuals.com. All Manuals Search And Download.
POLARIS PRODUCTS
Part No.
Description
Engine Lubricants
Fogging Oil (12 oz. Aerosol)
2870791
2877882
2877953
2877883
2877884
VES 2-Cycle Oil (qt./.95 l)
VES 2-Cycle Engine Oil (2 qt./1.9 l)
VES 2-Cycle Engine Oil (gal./3.8 l)
VES 2-Cycle Engine Oil (2.5 gal./9.5 l)
Chaincase Lubricants
2873105
2873106
SCL - Synthetic Chaincase Lubricant (qt./.95 l)
SCL - Synthetic Chaincase Lubricant (gal./3.8 l)
Grease/Specialized Lubricants
Grease Gun Kit, All Season (3 oz./89 ml)
All Season Grease (3 oz./89 ml cartridge)
All Season Grease (14 oz./414 ml cartridge)
Dielectric Grease (Nyogel™)
2871312
2871322
2871423
2871329
Coolant
2880514
2880513
POLARIS Extended Life Antifreeze 50/50 Premix (qt./.95 l)
POLARIS Extended Life Antifreeze 50/50 Premix (gal./3.8 l)
Additives/Miscellaneous
2871326
2870652
2872189
2872893
2870505
Carbon Clean
Fuel Stabilizer
DOT4 Brake Fluid
Engine Degreaser
Isopropyl Fuel De-Icer
137
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 RUSH PRO-S
Capacities and Dimensions
Body Style
AXYS
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
46 inches (117 cm)
114 inches (289.6 cm)
432 lbs. (196 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.3 in. (23.6 cm) / 13.6 in. (34.5 cm)
Engine and Cooling
Engine
Displacement
Cylinders
S4868-6044-OI6P
599cc
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
Oil Injection
Throttle Body Bore Size
Idle RPM
77.25 x 64
400 watt
Mikuni
Electronic Oil Pump
46 mm
1700 +/- 200
8250 +/- 200
Operating RPM
Cooling
Thermostat Opening Temp.
Liquid
120°F (49°C)
Ignition Type
Multi-Dimensional CDI
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
138
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 RUSH PRO-S
Clutching Chart
ALTITUDE
Drive Clutch
Meters
Drive
Chaincase
Gearing/
Pitch
Driven Clutch
Driven
Helix
Clutch
Spring
Spring
Shift Weight
(Feet)
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-64
1321585
600-1200
(2000-4000)
10-62
1321586
22:41-70
1200-1800
(4000-6000
10-60
1321587
140/330
7043829
Black/Purple
7043363
48/42-.36
5139626
1800-2400
(6000-8000)
10-58
1321588
2400-3000
(8000-10000)
10-56
1321684
21:42-70
3000-3600
(10000-12000)
10A-L
1321531
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
600 RUSH PRO-S Traction / Control
Traction / Control
Track / Pitch
15 x 120 x 1.25 Ripsaw II / 2.86
Maximum Stud Length
Tunnel Protection
1.325 in. (3.36 cm)
Integrated
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
139
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 RUSH PRO-X (International)
Capacities and Dimensions
AXYS
Body Style
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
46 inches (117 cm)
114 inches (289.6 cm)
432 lbs. (196 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.9 in. (25.2 cm) / 13.6 in. (34.5 cm)
Engine and Cooling
Engine
Displacement
Cylinders
S4868-6044-OI6P
599cc
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
Oil Injection
Throttle Body Bore Size
Idle RPM
77.25 x 64
400 watt
Mikuni
Electronic Oil Pump
46 mm
1700 +/- 200
8250 +/- 200
Operating RPM
Cooling
Thermostat Opening Temp.
Liquid
120°F (49°C)
Ignition Type
Multi-Dimensional CDI
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
140
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 RUSH PRO-X (International)
Clutching Chart
ALTITUDE
Meters
(Feet)
Drive
Clutch
Spring
Chaincase
Gearing/
Pitch
Drive Clutch
Shift Weight
Driven Clutch
Driven
Helix
Spring
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-64
1321585
600-1200
(2000-4000)
10-62
1321586
22:41-70
1200-1800
(4000-6000
10-60
1321587
140/330
7043829
Black/Purple
7043363
48/42-.36
5139626
1800-2400
(6000-8000)
10-58
1321588
2400-3000
(8000-10000)
10-56
1321684
21:42-70
3000-3600
(10000-12000)
10A-L
1321531
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
600 RUSH PRO-X (International) Traction / Control
Traction / Control
Track / Pitch
Maximum Stud Length
Tunnel Protection
15 x 120 x 1.75 Backcountry X / 2.86
Not Recommended
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
141
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK PRO-S
Capacities and Dimensions
AXYS
Body Style
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
46 inches (116.8 cm)
121 inches (307.4 cm)
447 lbs. (202.8 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.3 in. (23.6 cm) / 13.4 in. (34 cm)
Engine and Cooling
Engine
S4868-6044-OI6P
Displacement
599cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
77.25 x 64
400 watt
Mikuni
Oil Injection
Throttle Body Bore Size
Idle RPM
Electronic Oil Pump
46 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 +/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
142
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK PRO-S
Clutching Chart
ALTITUDE
Meters
(Feet)
Drive
Clutch
Spring
Chaincase
Gearing/
Pitch
Drive Clutch
Shift Weight
Driven Clutch
Driven
Helix
Spring
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-64
1321585
600-1200
(2000-4000)
10-62
1321586
22:41-70
1200-1800
(4000-6000
10-60
1321587
140/330
7043829
Black/Purple
7043363
48/42-.36
5139626
1800-2400
(6000-8000)
10-58
1321588
2400-3000
(8000-10000)
10-56
1321684
21:42-70
3000-3600
(10000-12000)
10A-L
1321531
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
600 SWITCHBACK PRO-S
Traction / Control
Track / Pitch
15 x 137 x 1.25 Ripsaw II / 2.86
Maximum Stud Length
Tunnel Protection
1.325 in. (3.36 cm)
Integrated
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
143
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK PRO-X (International)
Capacities and Dimensions
Body Style
AXYS
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
46 inches (116.8 cm)
121 inches (307.4 cm)
447 lbs. (202.8 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.9in. (25.2 cm) / 13.4 in. (34 cm)
Engine and Cooling
Engine
S4868-6044-OI6P
Displacement
599cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
77.25 x 64
400 watt
Mikuni
Oil Injection
Throttle Body Bore Size
Idle RPM
Electronic Oil Pump
46 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 +/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
144
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK PRO-X (International)
Clutching Chart
ALTITUDE
Meters
(Feet)
Drive
Clutch
Spring
Chaincase
Gearing/
Pitch
Drive Clutch
Shift Weight
Driven Clutch
Driven
Helix
Spring
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-64
1321585
600-1200
(2000-4000)
10-62
1321586
22:41-70
1200-1800
(4000-6000
10-60
1321587
140/330
7043829
Black/Purple
7043363
48/42-.36
5139626
1800-2400
(6000-8000)
10-58
1321588
2400-3000
(8000-10000)
10-56
1321684
21:42-70
3000-3600
(10000-12000)
10A-L
1321531
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
600 SWITCHBACK PRO-X (International)
Traction / Control
Track / Pitch
Maximum Stud Length
Tunnel Protection
15 x 137 x 1.75 Backcountry X / 2.86
Not Recommended
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
RMK Wide / 3 in. (7.62 cm)
145
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK ADVENTURE
Capacities and Dimensions
AXYS
Body Style
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
49 inches (124.5 cm)
121 inches (307.4 cm)
492 lbs (223.2 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.3 in. (23.6 cm) / 13.4 in. (34 cm)
Engine and Cooling
Engine
S4868-6044-OI6P
Displacement
599cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
77.25 x 64
400 watt
Mikuni
Oil Injection
Throttle Body Bore Size
Idle RPM
Electronic Oil Pump
46 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 +/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
146
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK ADVENTURE
Clutching Chart
ALTITUDE
Meters
(Feet)
Drive
Clutch
Spring
Chaincase
Gearing/
Pitch
Drive Clutch
Shift Weight
Driven Clutch
Driven
Helix
Spring
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-64
1321585
600-1200
(2000-4000)
10-62
1321586
22:41-70
1200-1800
(4000-6000
10-60
1321587
140/330
7043829
Black/Purple
7043363
48/42-.36
5139626
1800-2400
(6000-8000)
10-58
1321588
2400-3000
(8000-10000)
10-56
1321684
21:42-70
3000-3600
(10000-12000)
10A-L
1321531
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
600 SWITCHBACK ADVENTURE
Traction / Control
Track / Pitch
15 x 137 x 1.352 Cobra / 2.86
Maximum Stud Length
Tunnel Protection
1.325 in. (3.36 cm)
Integrated
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
147
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK ADVENTURE (International)
Capacities and Dimensions
Body Style
AXYS
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
49 inches (124.5 cm)
121 inches (307.4 cm)
492 lbs (223.2 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.9 in. (25.2 cm) / 13.4 in. (34 cm)
Engine and Cooling
Engine
S4868-6044-OI6P
Displacement
599cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
77.25 x 64
400 watt
Mikuni
Oil Injection
Throttle Body Bore Size
Idle RPM
Electronic Oil Pump
46 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 +/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
148
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
600 SWITCHBACK ADVENTURE (International)
Clutching Chart
ALTITUDE
Meters
(Feet)
Drive
Clutch
Spring
Chaincase
Gearing/
Pitch
Drive Clutch
Shift Weight
Driven Clutch
Driven
Helix
Spring
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-64
1321585
600-1200
(2000-4000)
10-62
1321586
22:41-70
1200-1800
(4000-6000
10-60
1321587
140/330
7043829
Black/Purple
7043363
48/42-.36
5139626
1800-2400
(6000-8000)
10-58
1321588
2400-3000
(8000-10000)
10-56
1321684
21:42-70
3000-3600
(10000-12000)
10A-L
1321531
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
600 SWITCHBACK ADVENTURE (International)
Traction / Control
Track / Pitch
Maximum Stud Length
Tunnel Protection
15 x 137 x 1.75 Backcountry X / 2.86
Not Recommended
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
International: RMK Wide / 3 in. (7.62 cm)
149
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 RUSH PRO-S
Capacities and Dimensions
Body Style
AXYS
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
46 inches (117 cm)
114 inches (289.6 cm)
431 lbs. (195.5 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
High Modulus PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.3 in. (23.6 cm) / 13.6 (34.5 cm)
Engine and Cooling
Engine
S4834-8044-0I8P
Displacement
795cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
85 x 70
400 watt
Mikuni
Oil Injection
Throttle Body Bore Size
Idle RPM
Electronic Oil Pump
48 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 +0/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
150
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 RUSH PRO-S
Clutching Chart
ALTITUDE
Drive Clutch
Meters
Drive
Chaincase
Gearing/
Pitch
Driven Clutch
Driven
Helix
Clutch
Spring
Spring
Shift Weight
(Feet)
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-66
1321584
600-1200
10-64
Blue / Black
7043064
(2000-4000)
1321585
Gold
7041148
23-37-68
1200-1800
(4000-6000
10-62
1321586
58/44-.36
1800-2400
(6000-8000)
10-60
1321587
2400-3000
(8000-10000)
Black
7043063
140/330
7043829
20-39-68
3000-3600
(10000-12000)
10-58
1321588
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
800 RUSH PRO-S
Traction / Control
Track / Pitch
15 x 120 x 1.25 Ripsaw II / 2.86
Maximum Stud Length
Tunnel Protection
1.325 in. (3.36 cm)
Integrated
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
151
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 RUSH PRO-X
Capacities and Dimensions
Body Style
AXYS
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
48 inches (121.9 cm)
114 inches (289.6 cm)
435 lbs. (197.3 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
High Modulus PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.9 in. (25.2 cm) / 13.6 in. (34.5 cm)
Engine and Cooling
Engine
S4834-8044-0I8P
Displacement
795cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
85 x 70
400 watt
Mikuni
Oil Injection
Electronic Oil Pump
Throttle Body Bore Size
Idle RPM
48 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 + 0/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
152
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 RUSH PRO-X
Clutching Chart
ALTITUDE
Drive Clutch
Meters
Drive
Chaincase
Gearing/
Pitch
Driven Clutch
Driven
Helix
Clutch
Spring
Spring
Shift Weight
(Feet)
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-66
1321584
600-1200
10-64
Blue / Black
7043064
(2000-4000)
1321585
Gold
7041148
22-41-70
1200-1800
(4000-6000
10-62
1321586
58/44-.36
1800-2400
(6000-8000)
10-60
1321587
2400-3000
(8000-10000)
Black
7043063
140/330
7043829
21-42-70
3000-3600
(10000-12000)
10-58
1321588
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
800 RUSH PRO-X
Traction / Control
Track / Pitch
15 x 120 x 1.75 Backcountry X / 2.86
Maximum Stud Length
Tunnel Protection
N/A
N/A
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
153
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 SWITCHBACK PRO-S
Capacities and Dimensions
AXYS
Body Style
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
46 inches (117 cm)
121 inches (307.4 cm)
446 lbs. (202.3 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
High Modulus PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.3 in. (23.6 cm) / 13.4 in. (34 cm)
Engine and Cooling
Engine
S4834-8044-0I8P
Displacement
795 cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
85 x 70
400 watt
Mikuni
Oil Injection
Throttle Body Bore Size
Idle RPM
Electronic Oil Pump
48 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 +0/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
154
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 SWITCHBACK PRO-S
Clutching Chart
ALTITUDE
Meters
(Feet)
Drive
Clutch
Spring
Chaincase
Gearing/
Pitch
Drive Clutch
Shift Weight
Driven Clutch
Driven
Helix
Spring
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-66
1321584
600-1200
10-64
Blue / Black
7043064
(2000-4000)
1321585
Gold
7041148
23-37-68
1200-1800
(4000-6000
10-62
1321586
58/44-.36
1800-2400
(6000-8000)
10-60
1321587
2400-3000
(8000-10000)
Black
7043063
140/330
7043829
20-39-68
3000-3600
(10000-12000)
10-58
1321588
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
800 SWITCHBACK PRO-S
Traction / Control
Track / Pitch
15 x 137 x 1.25 Ripsaw II / 2.86
Maximum Stud Length
Tunnel Protection
1.325 in. (3.36 cm)
Integrated
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
155
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 SWITCHBACK PRO-X
Capacities and Dimensions
AXYS
Body Style
Rider Capacity
1
Coolant Capacity
Chaincase Oil Capacity
4 qts. (3.8 l)
Fill to Spill / 8 - 10 oz. (237 - 296 ml)
Dependent on sprocket / chain size
Fuel Tank Capacity
Height
Length
Estimated Dry Weight
Oil Capacity (qts./l)
12 gal. (45.4 l)
48 inches (121.9 cm)
121 inches (307.4 cm)
450 lbs. (204.1 kg)
3.8 qts. (112.4 l)
Designed Width (in./cm)
Ski Center Distance
47 inches (119.4 cm)
42.5 inches (108 cm)
Brake Type
Fluid
Hayes Phantom Floating Piston
DOT 4
Drive Clutch Center Distance
10.625 inches (26.97cm)
Drive Belt Type
Projected Width
High Modulus PBO- Double Cog, Cut Finish
1.46 inches (3.7 cm)
Drive / Driven Clutches
Reverse
Front / Rear Travel
P-85 / Team LWT
POLARIS Electronic Reverse Control (PERC)
9.9 in. (25.2 cm) / 13.4 (34 cm)
Engine and Cooling
Engine
S4834-8044-0I8P
Displacement
795 cc
Cylinders
2
Bore x Stroke (mm)
Alternator Output
Throttle Body
85 x 70
400 watt
Mikuni
Oil Injection
Throttle Body Bore Size
Idle RPM
Electronic Oil Pump
48 mm
1700 +/- 200
Operating RPM
Thermostat Opening Temp.
Ignition Type
Ignition Timing
Spark Plug / Gap
Recommended Fuel Octane
8250 +0/- 200
120°F (49°C)
Multi-Dimensional CDI
18° @ idle 1700 RPM w/120°F (49°C) water temp
NGK BPR9ES /.027 inches (0.7 mm)
91 non-oxygenated recommended
(87 oxygenated minimum)
156
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
800 SWITCHBACK PRO-X
Clutching Chart
ALTITUDE
Meters
(Feet)
Drive
Clutch
Spring
Chaincase
Gearing/
Pitch
Drive Clutch
Shift Weight
Driven Clutch
Driven
Helix
Spring
*Shaded cells indicate factory settings.
0-600
(0-2000)
10-66
1321584
600-1200
10-64
Blue / Black
7043064
(2000-4000)
1321585
Gold
7041148
22-41-70
1200-1800
(4000-6000
10-62
1321586
58/44-.36
1800-2400
(6000-8000)
10-60
1321587
2400-3000
(8000-10000)
Black
7043063
140/330
7043829
21-42-70
3000-3600
(10000-12000)
10-58
1321588
NOTE: Use 2 gram lighter shift weights when operating in temperatures above 40°F (5°C).
800 SWITCHBACK PRO-X
Traction / Control
Track / Pitch
15 x 137 x 1.75 Backcountry X / 2.86
Maximum Stud Length
Tunnel Protection
N/A
N/A
IFS Shocks
FTS Shock
RTS Shock
Ski / Carbide
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
Walker Evans Piggyback / Compression Adj.
PRO-STEER / 4 in. (10.16 cm)
International: RMK Wide / 3 in. (7.62)
157
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Engine Troubleshooting
Unless you have experience and training in two-cycle engine repair, see
your dealer if technical problems arise.
Problem
Probable Cause Solution
Erratic engine
Drive clutch binding • SEE YOUR DEALER.
operating RPM
during acceleration
or load variations
Driven clutch
malfunction
• SEE YOUR DEALER.
• Replace the drive belt.
• SEE YOUR DEALER.
• Replace the drive belt.
Harsh drive clutch
engagement
Drive belt worn or
too narrow
Excessive belt/
sheave clearance
Drive belt turns over Wrong belt for
application
Clutch alignment out • SEE YOUR DEALER.
of spec
Engine mount
broken or loose
• Inspect and replace. SEE YOUR
DEALER.
Machine fails to
move
Clutch jammed
Track jammed
• Check for twisted belt or broken
spring. SEE YOUR DEALER.
• Foreign object may be caught or the
rail slide melted to the track clips
due to lack of lubrication.
• Track may be iced up or frozen to
the ground.
Chaincase sprocket
or chain jammed or
broken
• Chain is loose or broken or chain
tightener is loose. SEE YOUR
DEALER.
158
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Engine Troubleshooting
Problem
Probable Cause Solution
Noise in drive
system
Broken drive clutch • SEE YOUR DEALER.
components
Bearing failure/
chaincase, jackshaft,
or front drive shaft
• SEE YOUR DEALER.
Drive belt surface
flat spots
• Inspect and replace as needed.
Drive chain loose
• Inspect and adjust (or replace).
• SEE YOUR DEALER.
Drive chain worn,
sprocket teeth
broken
Poor low RPM
performance
Worn drive belt
• Inspect and replace as needed.
• SEE YOUR DEALER.
Excessive belt/
sheave clearance
Sticky clutch
• SEE YOUR DEALER.
Poor fuel quality
Seized engine
• Use 87-91 octane fuel (or higher).
Engine doesn't turn
• SEE YOUR DEALER. Seizure is a
result of poor lubrication,
inadequate fuel supply, broken parts
or improper cooling.
Hydrostatic lock
• Fuel may have entered the crankcase
while the vehicle was standing or
being transported. SEE YOUR
DEALER to correct the cause. Drain
plug(s) are located on the lower
crankcase for emergency draining.
159
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Engine Troubleshooting
Problem
Probable Cause Solution
Engine turns but fails Faulty ignition
to start
• Install new spark plug(s). If engine
still fails to start, check for spark. If
there's no spark, SEE YOUR
DEALER.
No fuel to engine
• Make sure the fuel tank contains
fuel.
• Ice may be in the fuel line, filter or
pump. Add isopropyl alcohol to the
fuel system.
Poor engine
compression
• This indicates a major engine
problem that must be repaired before
operating. SEE YOUR DEALER.
Engine lacks power
Fouled or defective
spark plug(s)
• Replace the plug(s).
Fuel filter (loss of
high RPM power)
• SEE YOUR DEALER.
Plugged fuel filter or • SEE YOUR DEALER.
tank pick-up sock
Incorrect clutching
Faulty plug(s)
• SEE YOUR DEALER.
Engine continually
backfires
• Change plug(s), ensure caps are
seated.
Fuel System
• Dirt or ice may be in the fuel system
(deicer should be added to non-
ethanol fuel at all times for
assurance against fuel line icing).
Incorrect throttle
freeplay or faulty
switch
• SEE YOUR DEALER.
Engine requires
more than normal
pulls to start
Poor fuel
• Replace with fresh winter fuel.
• SEE YOUR DEALER.
Not enough fuel
getting to engine
Plugged fuel filter or • SEE YOUR DEALER.
tank pick-up sock
160
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Suspension Troubleshooting
Problem
Solution
Rear suspension
bottoms too easily
• Adjust rear track shock clicker stiffer (see pages 57 and
58).
• Verify rear spring is not broken / dislodged.
• Rebuild rear track shock (see your dealer).
Rides too stiff in rear • Adjust rear track shock clicker softer (
• Check for binding suspension shafts and grease all pivot
points.
• Adjust rear track shock clicker to softer setting.
• Check track tension (see page 120).
Too much weight
transfer when
climbing
• Adjust rear shock spring (see pages 57 and 56).
Too little weight
transfer when
climbing
• Adjust rear shock spring (see pages 57 and 58).
Machine darts from
side to side
• Check ski alignment (see page 124).
• Make sure spindles and all steering components turn freely.
• Check for excessive play in steering assembly (see your
dealer).
• Ensure skags are straight on skis.
• Adjust rear shock spring (see pages 57 and 58).
• Check rail slide/replace if worn (see page 128).
Front end pushes
• Decrease front track shock spring preload in 1/8in.
increments.
• Increase front suspension shock spring preload in 1/8in.
increments
• Check for worn skags.
• Adjust rear shock spring (see pages 57 and 58).
• Check for binding front suspension shafts and steering
components.
Steering is heavy
• Make sure spindles and all steering components turn freely.
• Check ski alignment (see page 124).
• Check skags and skis for damage.
• Adjust rear shock spring (see pages 57 and 58).
• Increase front track shock spring preload in 1/8in.
increments
Track skips / ratchets • Track tension too loose (see page)
• Studs (if installed) are loose. Follow manufacture’s
installation instructions and re-torque studs.
161
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Drive Belt Troubleshooting
Belt Wear/Burn Diagnosis
Causes
Solutions
Driving at low RPM
• Drive at higher RPMs. Gear the machine down. Check
belt deflection.
Parking brake engaged
Insufficient warm-up
• Verify parking brake is not engaged.
• Warm the engine at least five minutes. Take the drive
belt off the snowmobile in extremely cold weather and
warm it up. Break snowmobile loose from the snow.
Towing at low RPM
• Do not tow in deep snow. Use fast, aggressive throttle
to engage clutch.
Riding with high RPM
and slow speed (8000
RPM/10 MPH/16 km/h)
• Lower the gear ratio. Reduce RPM. Avoid riding in
high ambient temperatures. Check for snow ingestion.
Ice and snow build-up
between track and tunnel
• Warm the engine at least five minutes. Take the drive
belt off the snowmobile in extremely cold weather and
warm it up. Break snowmobile loose from the snow.
Poor engine performance • Check for fouled plugs and water, ice or dirt in the fuel
tank or fuel line.
Loading snowmobiles
onto trailers
• Skis may gouge into trailers and prevent the drivetrain
from spinning properly. Use enough speed to drive the
snowmobile completely onto the trailer. Push and pull
it to finish loading if necessary.
Clutch malfunction
• Inspect clutch components. See your dealer.
• Use fast, aggressive throttle to engage clutch.
Slow, easy clutch
engagement
162
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Service and Warranty Information
Obtaining Service and Warranty Assistance
Read and understand the service data and the POLARIS warranty information
contained in this manual. Contact your POLARIS dealer for replacement parts,
service or warranty. Your dealer receives frequent updates on changes,
modifications and tips on snowmobile maintenance, which may supersede
information contained in this manual. Your dealer is also familiar with
POLARIS policies and procedures and will be happy to assist you.
When contacting us about parts, service, or warranty, always provide the
following information:
1. Serial number
2. Model number
3. Dealer name
4. Date of purchase
5. Details of trouble experienced
6. Length of time and conditions of operation
7. Previous correspondence
Use the page provided near the front of your owner’s manual to record the
identification numbers of your snowmobile and its engine.
POLARIS Customer Service
United States & Canada: 1-800-POLARIS (1-800-765-2747)
French: 1-800-268-6334
163
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Limited Warranty
POLARIS Industries Inc., 2100 Highway 55, Medina, MN 55340 (POLARIS) gives a
12 MONTH LIMITED WARRANTY on all components of your POLARIS vehicle
against defects in material or workmanship. This warranty covers parts and labor
charges for repair or replacement of defective parts and begins on the date of purchase
by the original retail purchaser. This warranty is transferable to another owner during the
warranty period through a POLARIS dealer, but any such transfer will not extend the
original term of the warranty. The duration of this warranty may vary by international
region based upon local laws and regulations.
THIS WARRANTY MAY BE VOIDED BY ANY UNAPPROVED MODIFICATIONS
TO THIS VEHICLE THAT AFFECT POWERTRAIN, EXHAUST, CHASSIS OR
SUSPENSION.
Promotional warranties are sometimes offered by POLARIS, including but not limited
to:
• Two-year extended engine coverage
• Two-year powertrain coverage
• Extended service contract
See your dealer for details and separate terms and conditions for any promotional
warranties.
Registration
At the time of sale, the Warranty Registration Form must be completed by your dealer
and submitted to POLARIS within ten days of purchase. Upon receipt of this
registration, POLARIS will record the registration for warranty. No verification of
registration will be sent to the purchaser as the copy of the Warranty Registration Form
will be your proof of warranty coverage. If you have not signed the original registration
and received the customer copy, please contact your dealer immediately. NO
WARRANTY COVERAGE WILL BE ALLOWED UNLESS YOUR VEHICLE IS
REGISTERED WITH POLARIS. Initial dealer preparation and set-up of your vehicle is
very important in ensuring trouble-free operation. Purchasing a machine in the crate or
without proper dealer set-up will void your warranty coverage.
164
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Warranty Coverage and Exclusions
Limitations of Warranties and Remedies
This POLARIS Limited Warranty excludes any failures that are not caused by a defect
in material or workmanship. THIS WARRANTY DOES NOT COVER CLAIMS OF
DEFECTIVE DESIGN. This warranty also does not cover acts of God, accidental
damage, normal wear and tear, abuse or improper handling. This warranty also does not
cover any vehicle, component or part that has been altered structurally, modified,
neglected, improperly maintained or used for racing, competition or purposes other than
for which it was designed.
This warranty also excludes failures resulting from improper lubrication; improper
engine timing; improper fuel; surface imperfections caused by external stress, heat, cold
or contamination; operator error or abuse; improper component alignment, tension,
adjustment or altitude compensation; failure due to snow, water, dirt or other foreign
substance ingestion/contamination; improper maintenance; modified components; use
of aftermarket components; unauthorized repairs; repairs made after the warranty period
expires or by an unauthorized repair center; use of the product in competition or for
commercial purposes. Warranty will not apply to any product which has been damaged
by abuse, accident, fire or any other casualty not determined a defect of materials or
workmanship.
This warranty excludes damages or failures caused by abuse, accident, fire or any other
cause other than a defect in materials or workmanship and provides no coverage for
consumable components, general wear items or any parts exposed to friction surfaces,
stresses, environmental conditions and/or contamination for which they were not
designed or not intended, including but not limited to the following items:
Skis
Ski wear rods
Tracks
Slide rails
Suspension components
Brake components
Seat components
Clutches and components
Steering components
Batteries
Finished and unfinished surfaces
Carburetor/Throttle body components
Engine components
Drive belts
Hydraulic components
Circuit breakers/Fuses
Electronic components
Spark Plugs
Light bulbs/Sealed beam lamps
Idler wheels
Sealants
Lubricants
Coolant
Filters
Fuel
165
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Warranty Coverage and Exclusions
Limitations of Warranties and Remedies
Lubricants and Fluids
1. Mixing oil brands or using non-recommended oil may cause engine damage. We
recommend the use of POLARIS engine oil.
2. Damage or failure resulting from the use of non-recommended lubricants or fluids is
not covered by this warranty.
This warranty provides no coverage for personal loss or expense, including mileage,
transportation costs, hotels, meals, shipping or handling fees, product pick-up or
delivery, replacement rentals, loss of product use, loss of profits, or loss of vacation or
personal time.
THE EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY SHALL BE, AT
POLARIS’ OPTION, REPAIR OR REPLACEMENT OF ANY DEFECTIVE
MATERIALS, COMPONENTS, OR PRODUCTS. THE REMEDIES SET FORTH IN
THIS WARRANTY ARE THE ONLY REMEDIES AVAILABLE TO ANY PERSON
FOR BREACH OF THIS WARRANTY. POLARIS SHALL HAVE NO LIABILITY
TO ANY PERSON FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES OF ANY DESCRIPTION, WHETHER ARISING OUT OF EXPRESS OR
IMPLIED WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE, OR
OTHER TORT OR OTHERWISE. THIS EXCLUSION OF CONSEQUENTAL,
INCIDENTAL AND SPECIAL DAMAGES IS INDEPENDENT FROM AND SHALL
SURVIVE ANY FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITS
ESSENTIAL PURPOSE.
THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE IS
EXCLUDED FROM THIS LIMITED WARRANTY. ALL OTHER IMPLIED
WARRANTIES (INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTY OF MERCHANTABILITY) ARE LIMITED IN DURATION TO THE
ABOVE 12 MONTH WARRANTY PERIOD. POLARIS DISCLAIMS ALL EXPRESS
WARRANTIES NOT STATED IN THIS WARRANTY. SOME STATES DO NOT
PERMIT THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR ALLOW LIMITATIONS ON THE DURATION
OF IMPLIED WARRANTIES, SO THE ABOVE LIMITATIONS MAY NOT APPLY
TO YOU IF INCONSISTENT WITH CONTROLLING STATE LAW.
166
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
How to Obtain Warranty Service
If your vehicle requires warranty service, you must take it to a POLARIS Servicing
Dealer. When requesting warranty service you must present your copy of the Warranty
Registration Form to the dealer. (THE COST OF TRANSPORTATION TO AND
FROM THE DEALER IS YOUR RESPONSIBILITY.) POLARIS suggests that you use
your original selling dealer; however, you may use any POLARIS Servicing Dealer to
perform warranty service.
In the country where your product was purchased:
Warranty or service bulletin repairs must be done by an authorized POLARIS dealer. If
you move or are traveling within the country where your product was purchased,
warranty and service bulletin repairs may be requested from any authorized POLARIS
dealer that sells the same line as your product.
Outside the country where your product was purchased:
If you are traveling temporarily outside the country where your product was purchased,
you should take your product to an authorized POLARIS dealer. You must show the
dealer photo identification from the country of the selling dealer’s authorized location as
proof of residence. Upon residence verification, the servicing dealer will be authorized
to perform the warranty repair.
If you move:
If you move to another country, be sure to contact POLARIS Customer Assistance and
the customs department of the destination country before you move. Product
importation rules vary considerably from country to country. You may be required to
present documentation of your move to POLARIS in order to continue your warranty
coverage. You may also be required to obtain documentation from POLARIS in order to
register your product in your new country. You should warranty register your product at
a local POLARIS dealer in your new country immediately after you move to continue
your warranty coverage and to ensure that you receive information and notices regarding
your vehicle.
If you purchase from a private party:
If you purchase a POLARIS product from a private party, to be kept and used outside of
the country in which the product was originally purchased, all warranty coverage will be
denied. You must nonetheless register your product under your name and address with a
local POLARIS dealer in your country to ensure that you receive safety information and
notices regarding your product.
167
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Exported Products
EXCEPT WHERE SPECIFICALLY REQUIRED BY LAW, THERE IS NO
WARRANTY OR SERVICE BULLETIN COVERAGE ON THIS PRODUCT IF IT IS
SOLD OUTSIDE THE COUNTRY OF THE SELLING DEALER’S AUTHORIZED
LOCATION. This policy does not apply to products that have received authorization for
export from POLARIS. Dealers may not give authorization for export. You should
consult an authorized dealer to determine this product’s warranty or service coverage if
you have any questions. This policy does not apply to products registered to government
officials or military personnel on assignment outside the country of the selling dealer’s
authorized location. This policy does not apply to safety bulletins.
Notice
If your product is registered outside of the country where it was purchased and you have
not followed the procedure set above, your product will no longer be eligible for
warranty or service bulletin coverage of any kind, other than safety bulletins. Products
registered to Government officials or military personnel on assignment outside of the
country where the product was purchased will continue to be covered by the Limited
Warranty.
Please work with your dealer to resolve any warranty issues. Should your dealer require
any additional assistance, they will contact the appropriate person at POLARIS.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state or in different countries. If any of the above terms are void
because of federal, state, local law, all other warranty terms will remain in effect.
For questions call POLARIS Customer Assistance:
United States & Canada: 1-800-POLARIS (1-800-765-2747)
French: 1-800-268-6334
168
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
U.S.A. EPA Emissions Limited Warranty
This Emissions Limited Warranty is in addition to the POLARIS standard Limited
Warranty for your vehicle. POLARIS Industries Inc. warrants that at the time it is first
purchased, this emissions-certified vehicle is designed, built and equipped so it
conforms with applicable U.S. Environmental Protection Agency emission regulations.
POLARIS warrants that the vehicle is free from defects in materials and workmanship
that would cause it to fail to meet these regulations.
The warranty period for this emissions-certified vehicle starts on the date the vehicle is
first purchased and continues for a period of 200 hours of engine operation; 4,000
kilometers (2,485 miles) of vehicle travel; or 30 calendar months from the date of
purchase, whichever comes first.
This Emissions Limited Warranty covers components if their failure increases the
vehicle’s regulated emissions, and it covers components of systems if their only purpose
is to control emissions. Repairing or replacing other components not covered by this
warranty is the responsibility of the vehicle owner. This Emissions Limited Warranty
does not cover components if their failure does not increase the vehicle’s regulated
emissions.
For exhaust emissions, emission-related components include any engine parts related to
the following systems:
•
•
Air-induction system
Fuel system
•
•
Ignition system
Exhaust gas recirculation systems
The following parts are also considered emission-related components for exhaust
emissions:
•
•
Aftertreatment devices
Crankcase ventilation valves
•
•
Sensors
Electronic control units
The following parts are considered emission-related components for evaporative
emissions:
•
•
•
•
•
•
•
•
•
Fuel Tank
Fuel Cap
Fuel Line
Fuel Line Fittings
Clamps*
Pressure Relief Valves*
Control Valves*
Control Solenoids*
Electronic Controls*
•
•
•
•
•
•
•
•
•
Vacuum Control Diaphragms*
Control Cables*
Control Linkages*
Purge Valves
Vapor Hoses
Liquid/Vapor Separator
Carbon Canister
Canister Mounting Brackets
Carburetor Purge Port Connector
*As related to the evaporative emission control system.
169
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
U.S.A. EPA Emissions Limited Warranty
The exclusive remedy for breach of this Limited Warranty shall be, at the exclusive
option of POLARIS, repair or replacement of any defective materials, components or
products. THE REMEDIES SET FORTH IN THIS LIMITED WARRANTY ARE THE
ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS
WARRANTY. POLARIS SHALL HAVE NO LIABILITY TO ANY PERSON FOR
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY
DESCRIPTION,WHETHER ARISING OUT OF EXPRESS OR IMPLIED
WARRANTY OR ANY OTHER CONTRACT, NEGLIGENCE OR OTHER TORT OR
OTHERWISE. THIS EXCLUSION OF CONSEQUENTIAL, INCIDENTAL, AND
SPECIAL DAMAGES IS INDEPENDENT FROM AND SHALL SURVIVE ANY
FINDING THAT THE EXCLUSIVE REMEDY FAILED OF ITS ESSENTIAL
PURPOSE.
ALL IMPLIED WARRANTIES (INCLUDING BUT NOT LIMITED TO ANY
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD DESCRIBED HEREIN. POLARIS DISCLAIMS ALL EXPRESS
WARRANTIES NOT STATED IN THIS WARRANTY. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply
if it is inconsistent with the controlling state law.
This Limited Warranty excludes failures not caused by a defect in material or
workmanship. This Limited Warranty does not cover damage due to accidents, abuse or
improper handling, maintenance or use. This Limited Warranty also does not cover any
engine that has been structurally altered, or when the vehicle has been used in racing
competition. This Limited Warranty also does not cover physical damage, corrosion or
defects caused by fire, explosions or other similar causes beyond the control of
POLARIS.
Owners are responsible for performing the scheduled maintenance identified in the
owner’s manual. POLARIS may deny warranty claims for failures that have been
caused by the owner’s or operator’s improper maintenance or use, by accidents for
which POLARIS has no responsibility, or by acts of God.
Any qualified repair shop or person may maintain, replace, or repair the emission
control devices or systems on your vehicle. POLARIS recommends that you contact an
authorized POLARIS dealer to perform any service that may be necessary for your
vehicle. POLARIS also recommends that you use only POLARIS parts. It is a potential
violation of the Clean Air Act if a part supplied by an aftermarket parts manufacturer
reduces the effectiveness of the vehicle’s emission controls. Tampering with emission
controls is prohibited by federal law.
If you have any questions regarding your warranty rights and responsibilities, please
contact POLARIS Customer Assistance:
United States & Canada: 1-800-POLARIS (1-800-765-2747)
French: 1-800-268-6334
170
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE LOG
Present this section of your manual to your dealer each time your
snowmobile is serviced. This will provide you and future owners with
an accurate log of maintenance and services performed on the
snowmobile.
DATE
MILES
(KM)
TECHNICIAN
SERVICE PERFORMED / COMMENTS
150 mi.
(240 km)
500 mi.
(800 km)
1000 mi.
(1600 km)
2000 mi.
(3200 km)
171
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE LOG
DATE
MILES
(KM)
TECHNICIAN
SERVICE PERFORMED / COMMENTS
172
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE LOG
DATE
MILES
(KM)
TECHNICIAN
SERVICE PERFORMED / COMMENTS
173
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
0-9
D
12-Volt Receptacle . . . . . . . . . . . . . 29
Drive Belt
Adjustment . . . . . . . . . . . . . . . . . 116
Break-In . . . . . . . . . . . . . . . . . . . . 76
Condition . . . . . . . . . . . . . . . . . . 115
Deflection . . . . . . . . . . . . . . . . . . 116
Installation . . . . . . . . . . . . . . . . . 118
Removal . . . . . . . . . . . . . . . . . . . 117
Safety . . . . . . . . . . . . . . . . . . . . . . 19
Drive Chain Tension . . . . . . . . . . . . 109
Driver Awareness . . . . . . . . . . . . . . . 15
Driveshaft Bearing Lubrication. . . . . 98
Driving Downhill. . . . . . . . . . . . . . . . 18
Driving in Hilly Terrain. . . . . . . . . . . 18
Driving on Slippery Surfaces . . . . . . 17
Driving Responsibly . . . . . . . . . . . . . 20
A
Adjustable Headlights . . . . . . . . . . . 28
Avalanches. . . . . . . . . . . . . . . . . . . . 16
B
Battery . . . . . . . . . . . . . . . . . . 129-133
Charging . . . . . . . . . . . . . . . 132-133
Installation . . . . . . . . . . . . . . . . 131
Removal . . . . . . . . . . . . . . . 129-130
Storage . . . . . . . . . . . . . . . 131, 135
Belt Break-In . . . . . . . . . . . . . . . . . . 76
Brake Fluid Level . . . . . . . . . . . . . . 69
Brake Lever Travel Inspection . . . . 69
Brakes . . . . . . . . . . . . . . . . 69, 110-112
Brake Fluid . . . . . . . . . . . . . . . . 111
Components . . . . . . . . . . . . . . . 110
Inspection . . . . . . . . . . . . . . . . . 110
Lever Travel . . . . . . . . . . . . . . . 110
System Bleeding . . . . . . . . . . . . 112
Break-In Period . . . . . . . . . . . . . . 75-76
E
Electrical Connections, Storage. . . . 136
Emission Control Information. . . . . . 87
Engine Break-In. . . . . . . . . . . . . . 75-76
Engine Overheating. . . . . . . . . . . 34-35
Engine Protection, Storage . . . . . . . 136
Engine Restarting . . . . . . . . . . . . . . . 74
Engine Safety. . . . . . . . . . . . . . . . . . . 11
Engine Serial Number . . . . . . . . . . . . . 8
Engine Starting . . . . . . . . . . . . . . . . . 74
Engine Stop Switch . . . . . . . . . . . . . . 81
Environment Preservation . . . . . . . . . . 6
Exhaust System . . . . . . . . . . . . . . . . 108
C
Carbide Skags . . . . . . . . . . . . . . . . . 65
Chaincase Oil. . . . . . . . . . . . . . . 98-101
Cleaning for Matte Finishes. . . . . . 134
Cleaning/Preservation, Storage . . . 135
Clutch Alignment Offset . . . . . . . . 114
Clutch Safety . . . . . . . . . . . . . . . . . . 19
Clutch System . . . . . . . . . . . . . 114-118
Clutch/Drive System Care, Storage 136
Cold Weather Drive-Away . . . . . . . 19
Control Arm Pivot Adjustment . . . 126
Coolant. . . . . . . . . . . . . . . . . . . . . . 105
Coolant Level. . . . . . . . . . . . . . . . . 105
Cooling System . . . . . . . . . . . . 105-107
Cooling System, Bleeding . . . . 106-107
Cooling System, Flushing . . . . . . . 106
Customer Service. . . . . . . . . . . . . . 163
F
Fasteners, Side Panel. . . . . . . . . . . . . 71
Fluid Change
Chaincase . . . . . . . . . . . . . . . 99-101
Coolant . . . . . . . . . . . . . . . . . . . . 106
Fluid Level
Brake Fluid . . . . . . . . . . . . . . . . . 111
Chaincase . . . . . . . . . . . . . . . . . . . 98
Coolant . . . . . . . . . . . . . . . . . . . . 105
Front (IFS) Shock Adjustments. . . . . 54
Front Suspension (IFS)
Factory Clicker Settings . . . . . . . . 53
Factory Spring Settings. . . . . . . . . 53
Inspection . . . . . . . . . . . . . . . . . . 123
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Fuel Filter . . . . . . . . . . . . . . . . . . . . 101
D
DET . . . . . . . . . . . . . . . . . . . . . . . 32-33
Diagnostic Display Codes . . . . . . 92-93
Diagnostic Display Mode . . . . . . . . 49
Disabled Operators . . . . . . . . . . . . . 13
174
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
F
O
Fuel Lines . . . . . . . . . . . . . . . . . . . . 101
Fuel Premix (Initial Fill). . . . . . . . . . 75
Fuel Pump. . . . . . . . . . . . . . . . . . . . 101
Fuel Recommendation . . . . . . . . . . . 79
Fuel System Deicers . . . . . . . . . . . . . 79
Fuel Type Selection . . . . . . . . . . . . . 31
Fuel Warnings. . . . . . . . . . . . . . . . . . 78
Odometer/Engine Hour Display . . . . 41
Oil Change, Chaincase . . . . . . . 99-101
Oil Injection System . . . . . . . . . . . . . 76
Oil Level, Chaincase. . . . . . . . . . . . . 98
Oil Level, Injection. . . . . . . . . . . . . . 80
Oil Recommendations . . . . . . . . . . . 75
Operating in Deep Snow. . . . . . . . . . 17
Operator Safety. . . . . . . . . . . . . . . 9-21
Overheating, Engine . . . . . . . . . . 34-35
G
Guide, Suspension Set-Up . . . . . 51-59
P
H
Parking Brake Lever Lock . . . . . . . . 70
Playback Function . . . . . . . . . . . . . . 41
Polaris Products / Part Numbers. . . 137
Pre-Ride Checklist . . . . . . . . . . . . . . 66
Pre-Ride Suspension Inspection . . . . 67
Handlebar Adjustments. . . . . . . . 60-61
Handlebar Angle. . . . . . . . . . . . . . . . 61
Handlebar Components
Fastener Torques . . . . . . . . . . . . . 62
Component Locations . . . . . . . . . 63
Headlight Replacement. . . . . . . . . . 113
Hood . . . . . . . . . . . . . . . . . . . . . . . . . 94
Hood Removal / Installation. . . . . . . 95
R
Rail Slide Wear. . . . . . . . . . . . . . . . 128
Recoil Rope Inspection. . . . . . . . . . . 71
Registration, Warranty . . . . . . . . . . 164
Reverse Operation . . . . . . . . . . . 84-85
Rider Capacity . . . . . . . . . . . . . . . . . 14
Rider Information Center . . . . . . 38-49
Riding Apparel . . . . . . . . . . . . . . . . . 12
Riding Position . . . . . . . . . . . . . . . . . 11
Riser Angle . . . . . . . . . . . . . . . . . . . . 60
I
Ice and Snow Build-up . . . . . . . . . . . 17
Ignition Lock System . . . . . . 35, 43-48
Ignition Switch . . . . . . . . . . . . . . . . . 73
Inadequate Snow Conditions . . . . . . 17
Indicator Lights. . . . . . . . . . . . . . . . . 37
Information Display Area . . . . . . . . . 40
Inspection, Pre-Ride . . . . . . . . . . . . . 66
Instrument Cluster. . . . . . . 36-45, 47-50
Intake Filters . . . . . . . . . . . . . . . . . . 102
Intake Silencer . . . . . . . . . . . . . . . . . 19
S
Saddlebags . . . . . . . . . . . . . . . . . . . . 30
Safety Labels . . . . . . . . . . . . . . . 22-25
Safety Symbols . . . . . . . . . . . . . . . . . . 9
Security System . . . . . . . . . . 35, 43-48
Set-Up Guide, Suspension . . . . . 51-59
Shock Lubrication, Rear Shock . . . . 98
Side Panel Fasteners . . . . . . . . . . . . . 71
Side Panels (Opening/Removing). . . 94
Signal Words . . . . . . . . . . . . . . . . . . . 9
Skags, Carbide . . . . . . . . . . . . . . . . . 65
Ski Alignment. . . . . . . . . . . . . . . . . 124
Ski Skags . . . . . . . . . . . . . . . . . . . . 125
Ski Toe Settings . . . . . . . . . . . . . . . 124
Slide Rail and Track Cooling . . . . . . 77
Snow Conditions. . . . . . . . . . . . . . . . 17
Spark Plug Condition . . . . . . . . . . . 104
Spark Plug Inspection. . . . . . . . . . . 104
Spark Plug Recommendations . . . . 103
Spark Plugs . . . . . . . . . . . . . . . 103-104
K
Key Identification . . . . . . . . . . . . . . . . 8
L
Lights/Replacement . . . . . . . . . . . . 113
M
Maintenance Interval Table . . . . 89-91
Maintenance Program. . . . . . . . . . . . 88
Maintenance Recommendations. . . . 10
Maneuverability . . . . . . . . . . . . . . . . 19
Matte Finish Cleaning. . . . . . . . . . . 134
Metric/Standard Display. . . . . . . . . . 42
175
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
S
T
Specifications/Clutching
Taillight/Brakelight Replacement . . 113
Throttle Lever . . . . . . . . . . . . 68, 82-83
Throttle Lever Freeplay. . . . . . . . 82-83
Throttle Release Switch. . . . . . . . . . . 81
Throttle Release Switch Inspection. . 68
Tools . . . . . . . . . . . . . . . . . . . . . . 96-97
Towing. . . . . . . . . . . . . . . . . . . . . . . . 86
Track
Alignment . . . . . . . . . . . . . . . . . . 122
Inspection . . . . . . . . . . . . . . . . . . 119
Lubrication . . . . . . . . . . . . . . . . . 119
Tension . . . . . . . . . . . . . . . . 120-121
Track Care, Storage . . . . . . . . . . . . . 136
Track Inspection . . . . . . . . . . . . . . . . 71
Track Maintenance . . . . . . . . . 119-122
Track Safety. . . . . . . . . . . . . . . . . . . . 11
Track Warm-Up. . . . . . . . . . . . . . . . . 77
Traction Products. . . . . . . . . . . . . 64-65
Transporting the Snowmobile . . . . . 136
Troubleshooting, Drive Belt . . . . . . 162
Troubleshooting, Engine . . . . . 158-160
Troubleshooting, Suspension. . . . . . 161
Tune-Up. . . . . . . . . . . . . . . . . . . . . . 134
600 RUSH PRO-S . . . . . . . . . . . . . . 138
600 RUSH PRO-X (Int’l) . . . . . . . . . 140
600 SWITCHBACK ADV . . . . . . . . 146
600 SWITCHBACK ADV (Int’l). . . 148
600 SWITCHBACK PRO-S. . . . . . . 142
600 SWITCHBACK PRO-X (Int’l) . 144
800 RUSH PRO-S . . . . . . . . . . . . . . 150
800 RUSH PRO-X . . . . . . . . . . . . . . 152
800 SWITCHBACK PRO-S. . . . . . . 154
800 SWITCHBACK PRO-X . . . . . . 156
Speed . . . . . . . . . . . . . . . . . . . . . . . . 14
Speed Display . . . . . . . . . . . . . . . . . 40
Standard/Metric Display . . . . . . . . . 42
Starting the Engine . . . . . . . . . . . . . 74
Starting the Engine, Restarting . . . . 74
Steering System . . . . . . . . . . . . 123-125
Steering System Inspection . . . . . . . 71
Stopping, Emergency. . . . . . . . . . . . 73
Storage Compartment, Heated. . . . . 29
Storage, Seasonal/Extended. . 134, 136
Storage, Daily . . . . . . . . . . . . . . . . . 86
Studs . . . . . . . . . . . . . . . . . . . . . . . . 64
Survival Preparation . . . . . . . . . . . . 13
Suspension Control Arms, Front . . 126
Suspension Inspection, Pre-Ride . . . 67
Suspension Inspection, Rear . . . . . 127
Suspension Quick Set-Up Guide . 51-59
Suspension, Rear . . . . . . . . . . . 127-128
Switches
V
Vehicle Identification Numbers. . . . . . 7
W
Wear Strips . . . . . . . . . . . . . . . . . . . . 65
Windchill . . . . . . . . . . . . . . . . . . . . . . 21
Engine Stop Switch. . . . . . . . . . . 81
Ignition Switch . . . . . . . . . . . . . . 73
Mode/Select Buttons. . . . . . . 36, 50
Mode/Set Switch. . . . . . . . . . 36, 50
176
Download from Www.Somanuals.com. All Manuals Search And Download.
For your nearest Polaris dealer,
call 1-800-POLARIS (765-2747)
or visit www.polaris.com
Polaris Industries Inc.,
2100 Hwy. 55, Medina, MN 55340
Part No. 9925073 Rev 01 Printed in USA
* 9 9 2 5 0 7 3
*
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Peerless Industries Telephone ACC 050 User Manual
Pelco Security Camera 9770 User Manual
Philips Baby Accessories SC280 User Manual
Philips Portable CD Player AX2401 55 User Manual
Philips Portable Speaker SPA5200 00 User Manual
Philips Speaker SBC BC735 User Manual
Philips Stereo System MX965 User Manual
Poulan Snow Blower PR8527ESA User Manual
ProForm Treadmill PFTL79022 User Manual
PVI Industries Water Heater PV500 44U User Manual