|
Fast / Gigabit Ethernet Switch Module
MII series
User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances in
electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
Revision
User’s manual for Fast / Gigabit Ethernet Switch Module
For model: MII-VSC / MII-VST / MII-VS15 / MII-VSA20 / MII-VSB20 /
MII-GT/ MII-SX / MII-LX / MII-L40 / MII-L70 / MII-SFP /
MII-LA15 / MII-LB15
Rev: 7.0 (JULY, 2008)
Part No: 2010-000021-007
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 OVERVIEW...................................................................... 5
Chapter 2 MODEL LIST ................................................................... 6
Chapter 3 CHECKLIST..................................................................... 7
Chapter 4 INTRODUCTION ............................................................. 8
4-1 1-Port 100Base-FX Fast Ethernet Modules-MII-VSC /
MII-VST / MII-VS15 / MII-VSA20 / MII-VSB20.................... 8
4-2 1-Port 1000Base-T Gigabit Ethernet Module-MII-GT............11
4-3 1-Port 1000Base-SX/LX Gigabit Ethernet
Modules-MII-SX / MII-LX / MII-L40 / MII-L70 /
MII-LA15 / MII-LB15........................................................12
4-4 1-Port 1000Base-T/Mini GBIC interface Module-MII-SFP ......14
Chapter 5 Installing Optional Modules..............................................16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 OVERVIEW
Thank you for purchasing PLANET MII family Fast / Gigabit Ethernet
module. The MII family Fast / Gigabit Ethernet module can install into
PLANET FNSW / FGSW family Switch. The distance can be extended
from 100 meters (TP), 2 kilometers (Multi-mode, SC or ST), up to 120
kilometers (Single-mode, SC/LC).
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 MODEL LIST
Your MII family Fast / Gigabit Ethernet module comes with one of the
following models.
Fiber connector
and distance
Model
Interface
Fast Ethernet
MII-VSC
100Base-FX Module
(SC, MM, 2km)
(ST, MM, 2km)
(SC, SM, 15km)
(SC, SM, 20km)
(SC, SM, 20km)
MII-VST
100Base-FX Module
100Base-FX Module
100Base-FX Module
100Base-FX Module
MII-VS15
MII-VSA20
MII-VSB20
Gigabit Ethernet
MII-GT
10/100/1000Base-T Module
1000Base-SX Module
1000Base-LX Module
1000Base-LX Module
1000Base-LX Module
1000Base-T/Mini-GBIC Module
1000Base-LX Module
1000Base-LX Module
(RJ-45, 100m)
(SC, MM, 550m)
(SC, SM, 10km)
(SC, SM, 40km)
(SC, SM, 70km)
(RJ-45, 100m)
(SC, SM, 15km)
(SC, SM, 15km)
MII-SX
MII-LX
MII-L40
MII-L70
MII-SFP
MII-LA15
MII-LB15
Models with LX or last two numbered characters indicate the fiber-port
is with “Single-Mode” optic fiber connector and the number indicates
the maximum distance in km. The rest will be “Multi-Mode” optic
fiber models.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 CHECKLIST
Your MII carton should contain the following items:
The MII family Fast / Gigabit Ethernet module
This user’s manual
If any item is missing or damaged, please consult the dealer from
whom you purchased your MII family Fast / Gigabit Ethernet module.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 INTRODUCTION
4-1 1-Port 100Base-FX Fast Ethernet Modules - MII-VSC /
MII-VST / MII-VS15 / MII-VSA20 / MII-VSB20
Figure 1. 1-Port 100Base-FX (SC, Multi-mode) Module Front View
Features:
● Comply with IEEE 802.3u, 100Base-FX Fast Ethernet standard
● 1 x 100Base-FX fiber ports (SC/ST/single SC fiber connectors)
● Store-and-Forward technology for abnormal packet filtering
● For establishing fiber link with cable length up to 2km (Multi-mode
module) and 15/20km (Single-mode module) or 412m (half-duplex
mode)
● Slide switch for Half /Full-Duplex selection (default in full-duplex)
● Plug and Play Installation
1. The fiber connector and distance support will be
different by various models.
2. The MII-VSA20/VSB20 should runs in pair. It means
you must connect MII-VSA20 in one end and another
MII-VSB20, for example, in the other end.
Note
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
LED DEFINITION
LED
Color
Function
Lit: indicate the link through that port is
successfully established.
Blink: indicate that the switch is actively sending
or receiving data over that port.
LNK/
ACT
Green
Lit: indicate that port is operating in full-duplex
mode.
Off: indicate that port is operating in half-duplex
mode.
FDX
Orange
Blink: if a collision is detected when the port is
in half-Duplex mode.
Table 1. LED definition of 100Base- FX module
Slide switch settings:
Figure 2 shows the 100Base-FX module slide switch overview and the
screen in Figure 3 appears shows the web settings for working under
100Mbps full-duplex mode and half-duplex mode.
Please make sure you have correctly configured the 100Base-FX
module in the same duplex mode between the module’s slide switch
and web interface speed duplex mode settings of module slots before
physically installing the modules.
FULL
HAL F
Figure 2. Slide switch overview of 100Base- FX module
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3. 100Base- FX module duplex mode setting of web interface
Table 2 below shows the settings for working under 100Mbps full-
duplex mode and half-duplex mode. Both module (slide-switch) and the
switch (web interface) should be fixed on the same mode.
Speed/duplex
100Full-duplex mode
Full-duplex mode
100 Full
100Half-duplex mode
Half-duplex mode
100 Half
Hardware (module)
Software (firmware)
Table 2. Settings of 100Base-FX module
Table 3 below shows the slide switch operation for full duplex and half
duplex mode.
Slide Switch Description
The module works on full duplex mode. The other side must
be also configured on full duplex mode. This provides up
to 2km distance by multi-mode module and 15/20km by
FDX
single-mode module.
The module works on half duplex mode. The other side must
HDX
be also configured on half duplex mode. This provides up to
412m distances.
Table 3. Slide switch settings of 100Base-FX module
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4-2 1-Port 1000Base-T Gigabit Ethernet Module-MII-GT
Figure 4. 1-Port 1000Base-T Module Front View
Features:
● Comply with IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet, IEEE
802.3ab Gigabit Ethernet standard
● 1 x 10/ 100/1000Mbps N-Way auto-negotiation switch port
● Automatic MDI/MDI-X crossover function
● Store-and-Forward technology for abnormal packet filtering
● Non-blocking and full wire speed forwarding rate
● LED indicators for Speed status
● Up to 100m over 4-pair UTP Cat.5e cable
● Plug & Play Installation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LED DEFINITION
LED
Color
Function
Lit: indicate that the port is operating at
1000Mbps.
LNK/ACT
1000
Off: indicate that the port is operating at 10
Mbps or 100Mbps.
Blink: indicate the traffic sending or receiving
over that port.
Green
Green
Green
Lit: indicate that the port is operating at
100Mbps.
Off: indicate that the port is operating at 10
Mbps or 1000Mbps.
Blink: indicate the traffic sending or receiving
over that port.
LNK/ACT
100
Lit: indicate that the port is operating at
10Mbps.
Off: indicate that the port is operating at 100
Mbps or 1000Mbps.
LNK/ACT
10
Blink: indicate the traffic sending or receiving
over that port.
Table 4. LED definition of 1000Base-T Module
4-3 1-Port 1000Base-SX/LX Gigabit Ethernet Modules-
MII-SX / MII-LX / MII-L40 / MII-L70 / MII-LA15 /
MII-LB15
Figure 5. 1-Port 1000Base-SX Module Front View
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Features:
● Comply with the IEEE 802.3z Gigabit Ethernet standard
● 1 X 1000Mbps fiber port (SX/LX/single SC fiber connectors)
● Store-and-Forward technology for abnormal packet filtering
● Full-duplex mode supported
● Plug and Play Installation
● LED indicators for LNK/ACT, FDX status
● MII-SX provide distance up to 220m over 62.5/125μm fiber cable
and 500m over 50/125μm fiber cable
● MII-LX provide distance up to 550m over multimode fiber cable and
10km over 9/125μm single mode fiber cable
● MII-L40 provide distance up to 550m over multimode fiber cable and
40km over 9/125μm single mode fiber cable
● MII-L70 provide distance up to 550m over multimode fiber cable and
70km over 9/125μm single mode fiber cable
● MII-LA15 / LB15 provide distance up to 550m over multimode fiber
cable and 15km over 9/125μm single mode fiber cable
1. The fiber connector and distance support will be
different by various models.
2. The MII-LA15/LB15 should runs in pair. It means you
must connect MII-LA15 in one end and another MII-
LB15, for example, in the other end.
Note
LED DEFINITION
LED
Color
Function
Lit: indicate the link through that port is
successfully established.
Blink: indicate that the switch is actively
sending or receiving data over that port.
LNK/ACT
Green
Lit: indicate that port is operating in full-
duplex mode.
FDX
Orange
Table 5. LED definition of 1000Base-SX/LX Module
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4 1-Port 1000Base-T/Mini GBIC interface Module-
MII-SFP
Figure 6. 1-Port 1000Base-T/Mini GBIC Module Front View
Features:
● Comply with the IEEE 802.3ab, IEEE 802.3z Gigabit Ethernet stan-
dard
● 1-Port 1000Base-T/Mini GBIC interface module
● High performance Store-and-Forward architecture
● Auto-MDI/MDI-X on 1000Base-T port
● Mini-GBIC interface for optional Mini GBIC module
● Plug and Play Installation
● LED indicators for LNK/ACT status on 1000Base-T port
● LED indicators for LNK/ACT, FDX status on Mini GBIC interface
The MII-SFP module does not supports the 1000Base-T
port and Mini-GBIC interface operate at the same time.
Note
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LED DEFINITION
Mini GBIC interface
LED
Color
Function
Lit: indicate the link through that port is
successfully established.
Blink: indicate that the switch is actively
sending or receiving data over that port.
LNK/ACT
Green
Lit: indicate that port is operating in full-
duplex mode.
FDX
Orange
Table 6. LED definition of Mini GBIC interface from MII-SFP Module
1000Base-T port
LED
Color
Function
Lit: indicate the link through that port is
successfully established.
Blink: indicate that the switch is actively
sending or receiving data over that port.
1000
LNK/ACT
Green
Lit: indicate the link through that port is
successfully established.
Blink: indicate that the switch is actively
sending or receiving data over that port.
100
LNK/ACT
Orange
Table 7. LED definition of 1000Base-T port from MII-SFP module
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Installing Optional Modules
You can purchase optional modules separately to meet the needs of
your network. The process of installing optional modules is the same.
Follow these steps to install the optional module:
1.Power the Switch off before installing the optional module.
2.Place the Switch on a flat surface. Grasp the thumbscrew on the
sides of the optional module or blank bracket and turn counter-
clockwise to unscrew them. You can also use a screwdriver. Remove
the old module or the blank bracket and set aside. Do not discard
the module or blank bracket. Put the module or blank bracket back
in if you remove the new module.
3.Install the new module by inserting it into the guides and sliding it in
until it stops (See Figure 7). Press it firmly until you feel the module
snap into place. Never force, twist or bend the optional module. The
optional module slides in smoothly.
4.Gently push the thumbscrews in and turn clockwise to tighten. Do
not over tighten the thumbscrews.
5.Power the Switch on after you have installed the new module. The
Switch will automatically detect the new module.
1
2
3
4
9
10
11
12
WGSW-2402A
Intelligent 10/100/1000Mbps Ethernet Switch
100Mbps
ACT
100Base
-
FX
1
9
2
3
4
5
6
7
8
LNK/ACT
100/10
LNK/ACT
100/10
PWR
Mbps
1000
TX
RX
WGSW-C1ST
10 11 12 13 14 15 16
100Base - FX
5
6
7
8
13
14
15
Slot
2
100
10
WGSW-C1GT
10/100/1000Base-T
Figure 7. Insert the modules
6.Take off the dust cover from the transceiver and plug the cable in, if
you are installing a fiber optic module.
7.Check the LEDs to verify that if there is a link and a proper connec-
tion at the port.
Please refer to the Switch’s user’s manual for more about Switch or
module’s management.
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
|