Planar Film Camera A480 PL User Manual

AKPro system with ATH1

transport shown

Planar Model A480-PL

Professional Grade

Home Cinema Conversion Lens System

USER MANUAL AND INSTALLATION GUIDE

Including the UH480 Lens, ATH1 Transport

and AKPro Projector Attachment Kits

As of February, 2009

Introduction, Basic projection parameters

Using the AKPro Attachment Kit

Important ceiling mount location considerations

Package Contents

Attachment Plate Diagram

Connecting the AKPro Attachment Plate – PD8130/PD8150

Mounting the ATH1 transport

Connecting the AKPro Attachment Plate – Viper

Mounting the ATH1 transport

Final adjustments

Programming

Aspect Ratio Matrix, Cleaning and Contact information

Page 1

Download from Www.Somanuals.com. All Manuals Search And Download.

USING the AKPro ATTACHMENT KIT

The AKPro includes a high performance, rigid, solid steel plate specifically designed to attach to

a properly installed ceiling mount head made by Chief Manufacturing (for use with the

PD8130/8150) or Premier (for use with the PD8130/8150 and Viper), which may then be further

installed to the ceiling using a variety of standard Chief or Premier mounting components.

These components are not included in the kit but are available. The ceiling mounts and

associated hardware must be installed to ceiling structural members to support at least

250 pounds and must be extremely rigid. Any play in the ceiling mount will result in a

rocking of the AKPro assembly as the lens moves in and out of the projector beam and

represents a danger to equipment and personnel.

The AKPro Attachment kit may also be used with a projector mount, but you must ensure that

the mount is suited to support the total weight. If you wish to use a different projector mount the

lens system is stabilized by using two chains extending from the front area of the plate to ceiling

attachment points. You may skip ahead to Page 6 and the section titled: “Alternate

Attachment Plate Method”

IMPORTANT CEILING MOUNT LOCATION CONSIDERATIONS

For optimum imaging results consult the projector’s instructions for the ceiling mount location to

place the projector’s lens in the horizontal center (ie left to right) of your projection screen (even

if the projector has a horizontal lens/image shift capability). In addition, make sure you are not

at the limits of your projector’s zoom capability so that you have some range for image

adjustments.

The AKPro attachment plate is designed so that the projector and other attached components

form an average center of mass (gravity) approximately located at the center of the ceiling

mount pipe. Therefore, the ideal ceiling mount location will be shifted by the AKPro 2”

(50mm) toward the left side of the screen from the ceiling mount location indicated by your

projector’s instructions.

If your projector ceiling mount is already installed and you do not wish to move it (or similarly

move the screen in the opposite direction) due to a shift by the AKPro system, then you can

make fine horizontal shift adjustments to your projector (if available) combined with turning the

projector (only as necessary) during final setup to compensate for the shift. Some small amount

of image distortion (horizontal keystoning) may result but in most cases this will not be

noticeable since the image edges will typically be masked by the screen borders.

WARNING!

Use extreme caution and appropriate hardware when installing heavy objects to a

ceiling. Periodically check all fasteners and connection hardware to be sure they are

not coming loose. Improper installation may lead to an increased risk of your

equipment becoming unstable and possibly injuring someone.

Page 3

Download from Www.Somanuals.com. All Manuals Search And Download.

PACKAGE CONTENTS

AKPro attachment plate, AKPro attachment bag (hardware, spacers), plate hook bag (chain,

hooks, hardware)

Transport, transport mounting hardware, lens bracket mounting hardware, power supply,

Panamorph remote, batteries

Page 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Panamorph lens and mounting bracket

Chief RPA ceiling mount (PD81xx use only)

Page 5

Download from Www.Somanuals.com. All Manuals Search And Download.

Top View (this side towards ceiling)

Front

Ceiling side of

Attachment Plate

8130/8150

7170

8130/8150

7170

8130/8150

7170

Rear

Page 6

Download from Www.Somanuals.com. All Manuals Search And Download.

PD8130/PD8150 installation instructions

CONNECTING THE AKPro ATTACHMENT PLATE

(Chief RPA mount and Phillips screwdrivers required)

1. Position the projector bottom-up on a soft surface. Consult the Attachment Plate

Diagram for plate orientation, mounting hole locations and required screws and spacers

for the PD8130 or PD8150. Insert and tighten each M4x30 screw through an

appropriate silver washer and lock washer, the designated holes in the Attachment

Plate, then through the 5/8” nylon spacers and finally into the projector ceiling mount

holes.

2. Using the included gold hex key, install the six 7/8” socket head screws each through a

3/8” aluminum spacer and into the six threaded holes from the ceiling side of the

attachment plate. Thread only enough to extend the screw to the bottom of the plate.

Page 7

Download from Www.Somanuals.com. All Manuals Search And Download.

MOUNTING THE ATH1 TRANSPORT

DO NOT CONNECT POWER TO THE TRANSPORT AT THIS TIME.

ATH1/M380 Attachment Bag Contents

Position the flat side of the

motorized transport against the bottom

side of the Attachment Plate so that the

transport logo is toward the screen and

the center “M” hole in the Attachment

Plate is aligned with the front recessed

transport hole. Insert the #10-32 pivot

screw up through the transport and

Attachment Plate and loosely complete

the assembly with the corresponding

washer, lock washer and nut. Now

loosely insert the four small 3/8” screws

Pivot screw as

assembled

#10-32x5/8” screw (1)

#10-32 nut (1)

Attachment

Plate

#10-32 lock washer (1)

#10-32 washer (1)

#6-32x3/8” screw (4)

ATH1 mount

through the four remaining “M” slots through the top of the Attachment Plate and down into the

transport.

M hole

M slots

Refer to the ATH1 user manual (included with ATH1) for additional instructions to install

the lens at this time, but do not forget to complete the “Final Adjustments” step below.

ATTACHING THE PROJECTOR TO THE CEILING MOUNT

Insure that the RPA mount head is secure (see instructions included with the RPA mount) and

oriented properly relative to the 7/8” socket head screw heads so that the mounted projector will

face the screen. Use two people to lift and position the projection assembly so that the heads of

each of the 7/8” socket head screws rest within the matching final location of the RPA mount

head. At this point the silver 3/8” spacers should be between the Attachment Plate and the RPA

mount head. The projection assembly may be lowered to allow the 7/8” screw heads to rest on

the RPA mount. However, a first person should continue to guide the projection assembly while

and a second person uses the gold assembly wrench to tighten the 7/8” screws. When

tightening these screws, do so in a pattern of incrementally driving each screw a little more into

the attachment plate so that at any time the projection assembly is resting on as many screw

heads as possible until all are tightened.

Page 8

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 9

Download from Www.Somanuals.com. All Manuals Search And Download.

If the lens must be removed for any length of time it is recommended that a similar weight be

suspended from the front of the attachment kit to balance the weight of the projector. This will

minimize unusual stresses on the ceiling mount system.

Proceed to “Final Adjustments” later on in this manual.

Page 10

Download from Www.Somanuals.com. All Manuals Search And Download.

Viper (PD7170) installation instructions

CONNECTING THE AKPro ATTACHMENT PLATE AND

CEILING MOUNT

(Planar/Premier PDS mount P/N 997-5351-00 and Phillips screwdrivers required)

1. Position the projector bottom-up on a soft surface. Consult the Attachment Plate

Diagram for plate orientation, mounting hole locations and required screws and spacers

for the Viper. Align the bottom part of the Planar/Premier PDS mount with the

attachment plate holes and insert and tighten each M4x30 screw through an appropriate

silver washer and lock washer, the designated holes in the Attachment Plate, then

through the 5/8” nylon spacers and finally into the projector ceiling mount holes.

Page 11

Download from Www.Somanuals.com. All Manuals Search And Download.

VIPER (PD7170) ATTACHMENT SECURITY HOOK

ATTACHMENT

(Phillips screwdrivers, pliers, scissors and appropriate ceiling hooks required)

Plate Hook Bag Contents (AK6 only)

#8-32 Wire Hook (2)

#8-32 Nut (4)

Ceiling

side

#8 Washer (4)

M4 Lock Washer (2)

Plate Hook

3/16” Chain (6 feet)

Chain End (4)

as assembled to

Attachment Plate

Ceiling Mount

adapter

Attachment

Screws

1. Install the Plate Hook Assemblies in the two “H”

holes of the Attachment Plate (see diagram) with the

hook ends on the ceiling side as shown above. Use

pliers to bend the closed hooks apart just enough to

install a Chain End at a later time.

Attachment

Plate

Spacers

2. Install ceiling hooks (not supplied) into the ceiling

directly above the Plate Hooks. The ceiling hooks

should be small enough to accept a Chain End

but strong enough when installed to each support 40 pounds or more.

5. Attach a Chain End to the Chain and then connect to one of the ceiling hooks. Cut the Chain

and assemble to another Chain End for a best fit to the corresponding Plate Hook and attach.

Repeat for the other set of hooks.

Page 12

Download from Www.Somanuals.com. All Manuals Search And Download.

MOUNTING THE ATH1 TRANSPORT

DO NOT CONNECT POWER TO THE TRANSPORT AT THIS TIME.

ATH1/M380 Attachment Bag Contents

Position the flat side of the

motorized transport against the bottom

side of the Attachment Plate so that the

transport logo is toward the screen and

the center “M” hole in the Attachment

Plate is aligned with the front recessed

transport hole. Insert the #10-32 pivot

screw up through the transport and

Attachment Plate and loosely complete

the assembly with the corresponding

washer, lock washer and nut. Now

loosely insert the four small 3/8” screws

Pivot screw as

assembled

#10-32x5/8” screw (1)

#10-32 nut (1)

Attachment

Plate

#10-32 lock washer (1)

#10-32 washer (1)

#6-32x3/8” screw (4)

ATH1 mount

through the four remaining “M” slots through the top of the Attachment Plate and down into the

transport.

M hole

M slots

3. Refer to the ATH1 user manual (included with ATH1) for additional instructions to install the

lens at this time, but do not forget to complete the “Final Adjustments” step below.

Page 13

Download from Www.Somanuals.com. All Manuals Search And Download.

ATTACHING THE PROJECTOR TO THE CEILING MOUNT

Follow the instructions included in the PDS mount to securely attach it to the ceiling

Attach the projector to the ceiling mounted portion of the PDS mount

Page 14

Download from Www.Somanuals.com. All Manuals Search And Download.

Page 15

Download from Www.Somanuals.com. All Manuals Search And Download.

FINAL ADJUSTMENTS (ALL INSTALLATIONS)

Turn the projector on with the UH480 Lens out of the projector beam. Set the horizontal

lens shift to neutral (if a feature of your projector) and then adjust the ceiling mount so that the

16:9 image is in the exact center of and square to the screen, with a similar amount of image

slightly over the top and bottom screen borders. If the projector lens is not in the exact

horizontal center of the screen you may need to use a little horizontal lens shift for this purpose.

Bring the UH480 Lens into the beam. Adjust the vertical position and tilt of the Lens so

that the projector beam is passing through the center of the Lens and so any residual

pincushion distortion is about the same at the top and bottom of the image. This will typically

result in the UH480 Lens being below the center of the projector lens and tilted slightly

downward. Tighten the knobs.

Adjust the rotation of the ATH1 transport so that the left and right sides of the image are

an equal distance from their respective screen borders. Now tighten the Pivot Screw (M380)

and also the four remaining screws holding the transport to the Attachment Plate.

For optimum multiple aspect ratio performance, adjust the projector’s zoom so that a

1.85:1 aspect ratio movie (Lens “out”) is just masked by the top and bottom of the screen

border. This way 1.85:1, 16:9 and 2.35-2.4:1 aspect ratio movies should all be presented to fill

the screen at a constant height.

Remove the protective film from the front of the Panamorph lens

Page 16

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming

Connect the included power adapter to the power input and connect a 3.5mm mini jack to

3.5mm mini jack cord that is long enough to reach from the Panamorph transport motor to the

rear of the Planar projector (not included) to the “+12V Trigger In” on the Panamorph transport

motor

Plug the other end of the 3.5mm mini jack into one of the two 12V triggers located on the rear

panel of the projector.

With the lens in the “out” position, bring up the projector menu. Navigate to the “Control” tab and

select “Letterbox” for the trigger that you attached 3.5mm cable from the Panamorph transport.

Page 17

Download from Www.Somanuals.com. All Manuals Search And Download.

Now when the aspect on the projectors aspect ratio is changed to “Letterbox”, the 12V trigger

will activate and the Panamorph lens transport will position the Panamorph lens in front of the

projectors primary lens.

Page 18

Download from Www.Somanuals.com. All Manuals Search And Download.

Aspect Ratio Matrix

Native Source

Aspect

Projector Aspect and

12V trigger Setting with

Panamorph Lens

Resulting Aspect

on Screen

16:9

16:9 letterbox

4:3

Letterbox

4:3 Narrow

16:9

2.35:1

4:3

You can program the projector control the lens and screen mask for one resize mode, such as

16:9 letterbox to 2.35:1, or leave the Panmorph lens in front of the lens all the time and adjust

the aspect raito per source type.

CLEANING

In most applications lenses do not need very much cleaning – a bit of dust will not impact image

clarity. However, in today’s high performance home cinemas with very dark rooms a small

build-up of dust or other foreign matter on your projector lens or your Panamorph lens can

produce a measurable reduction in contrast. The most effective cleaning approach is to simply

blow off any dust. If there is any residue or build-up then it is recommended that you clean the

optics with professional lens cleaning supplies such as from a camera store while the lens is in

front of the lit beam of the projector. This will allow you to quickly see both the results of

cleaning and also if you are causing any damage.

Planar Systems

1195 NW Compton Drive

Beaverton, OR, 97006

http://www.planar.com

Page 19

Download from Www.Somanuals.com. All Manuals Search And Download.

Pelco Pet Fence MM22 User Manual
Pelco Security Camera C2941M User Manual
Philips DVD Player DVD619 User Manual
Philips Indoor Furnishings 22AV3100 User Manual
Philips Network Card SLA5520NS User Manual
Philips Stereo Amplifier BGD885 User Manual
Philips Universal Remote RC4370 User Manual
Philips Vacuum Cleaner FC9166 9160 User Manual
Poulan Snow Blower 428861 User Manual
Premier Mounts TV Mount INW 42 User Manual