Planar Car Video System LX1250TI User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
LX1250TI User Manual  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
USAGE Notice  
Precautions  
To maximize the life and safe use of your unit, always be sure to follow the warnings, precautions and  
maintenance recommendations in this user’s guide.  
In a Vehicle:  
The monitor should be visible to the driver only if it is used for navigation, system control or vehicle  
information. If the monitor will be used for other purposes, it should be installed in a way that it will  
only operate while the vehicle is not moving (such as when the parking brake is in use), or so that its  
display is not visible to the driver. Review all applicable state and local laws and regulations to make  
sure the monitor is used properly and safely. Avoid using the monitor for extended times while the  
vehicle is not running, or the monitor could drain the vehicle’s battery.  
Cleaning the Monitor:  
Always turn of the unit before cleaning. Use a soft cloth moistened with mild detergent, isopropyl  
alcohol, or window cleaners to clean the display housing. Never use abrasive cleaners, waxes or  
solvents to clean the unit.  
Accessory Cables:  
The LX1250TI (PN# 997-6186-00LF) requires a special interface cable. This manual contains information  
to design the interface cable OR an accessory interface cable can be purchased.  
PN#. 997-5886-00LF GlenAir to VGA, Power, USB & Audio  
For remote control: Download USB to RS232 Driver from Planar website at  
LX1250TI User Manual  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Introduction  
About Planar’s LX1250TI Rugged Touch Monitor  
The LX1250TI is a high-performance, rugged touch monitor intended for demanding environments,  
such as those inside mining vehicles. The monitor features a 12.1-inch diagonal liquid crystal display  
with XGA resolution, bright enough to be read in full sunlight. The monitor also includes a buzzer for  
audio feedback and a sturdy cast aluminum enclosure that can withstand shock and vibration.  
Product  
This manual applies to product  
Planar Part Number  
997-6186-00LF  
Planar Model Name Description  
UPC  
IR touch 12.1” XGA LCD  
LX1250TI  
LX1251TI  
8 10689 06186 1  
General Market  
IR Touch 12.1” XGA LCD  
997-6192-00LF  
8 10689 06192 2  
General Market VGA IF  
LX1250TI User Manual  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Figure 1 Rendering of the display  
1
2
3
4
Reference Document # 076-0672-00 for detailed drawings.  
Front View (Descriptions):  
1. Backlight control +  
2. Backlight Control –  
3. LED:  
Green When video present;  
Amber when there is no video signal present and the monitor will go into standby mode.  
LED remains Amber in Standby Mode  
Off no power to display.  
4. Power Switch Pass through for remote PC shutdown. N.O. SPST switches (not Monitor Power)  
an external device.  
LX1250TI User Manual  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
All mounting & strain relief holes M4 x 8 mm  
LX1250TI User Manual  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product highlights  
Designed for demanding transportation environment  
Optimized for in cab sunlight viewability  
One button Display/CPU power on/off  
Control of backlight dimming and other OSD functions though USB interface  
Wide Voltage input with transient protection  
Low EMI  
Wide operating temperature range without fans or ventilation  
Vibration and Shock tested to rugged transportation specifications  
Waterproof enclosure design  
Rugged Aluminum enclosure  
12.1” XGA high bright display for viewability in all environments  
Infrared touchscreen with strengthened glass touch surface for the best optical clarity  
Wide dimming range controlled via USB or Bezel buttons  
Fanless die cast aluminum chassis with an IP65 design  
Single integrated Mil-Std connector for all connections  
Also available with separate VGA, Power, and USB connectors  
LED backlight for increased ruggedness, lower power, better EMI performance, better  
environmental impact (no mercury) and to minimize overall monitor depth and weight  
Hazardous materials compliant for international deployment  
Features:  
Brightness control allows you to easily adjust the display to match ambient light, from full  
sunlight to nigh. Even while wearing gloves. The convenient buttons enable quick  
adjustments.  
The monitor’s optically bonded display reduces the effects of reflected light on the display,  
increasing contrast ratio and read-ability in high ambient lighting conditions.  
The monitor’s autosync function eliminates the need for adjusting the monitor for best  
image. The monitor automatically adjusts to the input signal.  
HID Compliant IR Touch screen provides a durable touch environment that allows for  
operation in all conditions including with gloved hands. HID compliance means no touch  
drivers required.  
The monitor supports standard VGA input signals native 1024 x 768 (XGA) as well as 800 x  
600 (SVGA) and 640x480 VGA.  
The aluminum enclosure has a waterproof front and is designed to withstand substantial  
shock and vibration.  
LX1250TI User Manual  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Package Overview  
The following items are shipped with the display:  
Monitor  
Quick Start Guide  
NOTE: No cables ship with the monitor. Cables are purchased separately.  
Installation  
Before Installing  
Keep the following in mind while installing the monitor.  
• The monitor should be visible to the driver only if it is used for navigation, system control or vehicle  
information. If the monitor will be used for other purposes, it should be installed in such a way that it  
will only operate while the vehicle is not moving (such as when the parking brake is in use). Review all  
applicable state and local laws and regulations to make sure the monitor is used properly and safely.  
• The installed monitor must not interfere with the driver’s vision.  
Installing the LX1250TI monitor consists of three steps:  
1. Testing Touch Screen functionality with application software - see page 26.  
2. Securely routing the interface cable  
3. Mounting the monitor using one of the mounting options available on the back of the display  
enclosure. - see page 31.  
4. Connecting the monitor to the computer and power source - see page 17  
Note: The touch sensor is factory tested & calibrated, however different computing environments may  
require the touch screen to be recalibrated. Windows & Linux tools can be downloaded at:  
No standard On Screen Display (OSD) buttons are available to the user: All ‘standard’ OSD  
functionality can be controlled via the remote interface.  
The user controls are limited to Backlight +/- & Remote Power buttons.  
The All-in-One power button: A power button located on the front of the display functions as a  
pass though to turn on and off a remote computer. It functions very similar to a laptop  
computer docking station power button. The button is a Normally Open, Single Pull Single  
Throw Switch. It is not designed for current carrying switching.  
When there is no video detected, the monitor will go into standby mode. The LED will remain in  
Amber state in Standby Mode.  
No Base, mounting brackets, or stand is shipped with this device. It is a monitor head only.  
LX1250TI User Manual  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
No cables or power supply are shipped with this monitor, they are available as accessories for order  
separately.  
Electrical & SW Installation:  
Prior to end unit installation verify display works with computing system.  
1. Power up display:  
a. Display requires 9-32V DC with a maximum of 1.88A  
2. Test touch functionality. Connect cable to display and apply power.  
3. Connect Display to a computer.  
4. Display should auto sync to source signal. Ensure source meets supported display resolutions  
(XGA, SVGA, VGA).  
5. Connect USB touch screen to display.  
a. If Windows PC, PC should auto detect and configure touch sensor as HID compliant  
device.  
6. Verify touch response and accuracy.  
a. If Touch alignment is reversed install Touch calibration tools  
NOTE: Touch screen is calibrated at factory. Some computer interfaces may require recalibration at  
installation. Regular Calibration is not required.  
7. Once monitor is verified working with PC proceed to mechanical installation.  
Mechanical Installation:  
Display may be mounted in several configurations.  
a) Panel mounting  
b) VESA 100 or 75mm  
c) RAM 34.5mm x 40mm Triangle mount.  
If Vibration is a concern, consider mounting display using vibration dampening mount.  
1
2
3
4
Choose mounting option & Location  
Refer to dimensions figure for mounting holes and locations.  
Attach display to mounting hardware.  
Rout cable.  
NOTE: GlenAir cable should be mounted with strain relief to avoid excessive loading or  
torquing of the cable connectors. Improper cable installation will void warranty.  
LX1250TI User Manual  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the display:  
1. Once installed and cabled. The display is ready to use.  
2. Apply system power.  
3. Display & Touch screen are active  
Using the Touchscreen  
1. The LX1200TI touchscreen allows you to operate the computer by touching the screen with a  
I nger or stylus, rather than using a mouse or keyboard.  
2. Navigating the Touchscreen  
To click an item, tap the item once.  
To double-click an item, tap the item twice rapidly.  
To drag an item, touch the item, and then drag it along the screen to the new location.  
3. To move the cursor, touch the screen and move the cursor as needed.  
Using Remote OSD features:  
This is an advanced feature and should only be attempted by qualified individuals.  
The display allows for remote PC management. The display is controlled via the USB interface. The  
controlling PC requires a virtual COM port to operate the display. Drivers for the Display Virtual  
comport can be found here:  
Commands for control are as follows:  
2.1  
Display Control Serial Commands/Queries  
The display must support the following commands and queries using a protocol compatible with the  
Pixel works PW Host protocol.  
Support required for Phase II and beyond.  
LX1250TI User Manual  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
LX1250TI User Manual  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The following table defines the factory set values for the adjustable  
parameters.  
Parameter  
Default Setting  
Power  
On  
Image Scale  
Contrast  
Fill All  
150 ( Range 0 -255)  
150 ( Range 0 -255)  
7300C  
Brightness  
Color Temperature  
Gamma  
Linear  
Backlight brightness*  
255  
*Backlight retains previous brightness settings.  
Auto Power On  
The display automatically turns on when power is restored after a power  
failure and maintains all operational settings. Note: “on/off” refers to the  
LCD panel and the backlight inverter.  
Standby Mode  
If no video is present, after 10 seconds, the display powers off  
(will power back on once video is detected.)  
No Burn-in during Signal Loss  
The AMLCD will not maintain any static self-generated images  
(such as a “no video” text box when video is not present), thus avoiding  
image burn in.  
2.1.2  
Details of Command Implementation  
All serial commands must be compatible with the Pixel works PW Host  
protocol defined in the Pixel works application note AN#77. Refer to AN  
#77 for protocol details.  
The physical layer used for data exchange is RS232. No handshaking is  
used. Pin 3 of the DB-9 connector on the display is data transmitted from  
the host (Tx); pin 2 is data transmitted from the display and received by  
the host (Rx).  
LX1250TI User Manual  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
LX1250TI User Manual  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LX1250TI User Manual  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting the Monitor  
LX1250TI User Manual  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you are experiencing trouble with the LX1200TI monitor, refer to the  
following. If the problem persists, please contact your local dealer or our  
service center.  
Problem: No image appears on screen  
• Make sure the brightness is not turned all the way down.  
• Make sure all data and power cables are properly connected to the  
monitor and to the computer and power supply - see page17 for details.  
• Make sure the pins on the cables and connectors are not crooked or  
broken.  
• Make sure the computer is functioning properly, and has not entered  
power-saving mode. (You may also want to disable the computers  
power-saving feature.)  
Problem: Partial image or incorrectly displayed image  
• Make sure the computer’s image resolution is set to one of these  
resolutions: 1024 x 768 (XGA), 800 x 600 (SVGA) or 640 x 480 (VGA).  
Problem: Image is scrolling  
• Check and make sure the VGA signal cable (or adapter) is securely  
connected at both ends.  
Problem: No sound  
• Make sure the volume is not turned completely down.  
• Make sure the audio cable is securely connected at both ends.  
• Make sure the computer’s audio is not muted.  
Problem: The monitor does not appear to respond to the touchscreen  
• Make sure the USB cable to the computer is securely connected at both  
ends.  
LX1250TI User Manual  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Performance Conditions  
Performance characteristics are guaranteed over the environmental specification range.  
This product will be in used in the following conditions:  
Dusty environments  
High ambient lighting, outdoors and in a vehicles  
Scratched and banged with other equipment in the vehicle  
Very high vibration and shock environment  
Vandalism and tamper proofing: This product may be in environments that are unattended  
and used by people that are hard on their equipment  
This product will be driven by remote computers that can be far away. Product testing and  
verification was done with cables of at least 15ft. USB cables require a hub or booster for  
testing at lengths over 15 ft.  
Cleaning guidelines  
The LX1250TI will continue to operate normally while being cleaned in a fashion normal for a  
transportation environment. This includes cleaning with a damp (wrung out), mild soapy cloth.  
The LX1250TI will withstand cleaning solutions used in transportation. Possible chemicals include:  
70% isopropyl alcohol  
1.6% aqueous ammonia  
Formula 409®  
Fantastic®  
Cooling  
Cooling will be provided solely by convection cooling (no fan).  
Functional Specifications  
All specifications apply to both LX1250TI & LX1251TI Unless specifically noted.  
Manual Dimming Control  
Dimming control shall be two buttons that are easy to access and use with gloved hands. Dimming  
range shall be from max bright to minimum brightness.  
USB dimming control  
It is possible to access OSD functions via USB interface. To control display remotely, install Virtual COM  
Port drivers.  
Auto Sync  
The display will Autosync to video if both ‘+’ and ‘-‘ are pushed at the same time  
LX1250TI User Manual  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Volume Control  
None: through OS control only. Only available on LX1250TI, LX1251, does not have Audio.  
Function Buttons on Front of display  
The LX1250TI will have buttons and LEDs on the front of the display for user interaction. All buttons  
are silicon with positive feedback and backlight with white LEDs  
Power interrupt button (All-in-one power button)  
This button is not connected to the monitor power. The power interrupt button passes through to the  
rear IF connector. It shall be a SPST,N.O. momentary push button.  
(+) Button  
This button increases brightness of the backlight  
(-) Button  
This button decreases the brightness of the backlight  
LED status light  
The Monitor shall have a single LED for video status.  
LED green  
The LED Shall be green with there is video present  
LED amber  
The LED shall be amber when there is no video signal present and the monitor will go into standby  
mode.  
Module Specifications  
This section describes the internal components of this monitor.  
(Refer to Block Diagram in the Product Description Section 1.4)  
AMLCD  
Industrial grade with high bright LED backlight  
Touchscreen  
Infrared type: sensors and controller located in bezel  
Touch surface  
3mm solid glass, chemically strengthened, Anti glare coating AG level 110.  
The touchscreen will function even if the surface is scratched or broken.  
Touchscreen interface  
USB - HID  
Touchscreen resolution  
4096 X 4096  
Touchscreen driver  
Windows XP, Linux kernel ( Fedore Code 4 ) support  
LX1250TI User Manual  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Touchscreen controller  
Built into touch screen frame  
Externally accessible for firmware updates  
Video Controller board  
Requires standard VGA  
Auto sync on power up and any video mode change. Video Modes supported:  
Resolution Vertical refresh  
rate  
1024*768 60 Hz  
800*600 60 Hz  
640*480 60Hz  
More available  
When there is no VGA signal present, it will show “No Signal message" within 1 second and the  
LED over the power button (B1) will go amber.  
Pezio function LX1250TI only  
Function: provides audio warning signals  
Location: Rear of display.  
To use Buzzer:  
Apply a 500hz-1khz, 500mv-1V sign wave to the Audio Input signals. Duration of the signal controls  
perceived volume (1ms minimum @1khz,2ms minimum @500hz).  
Mechanical enclosure  
Function: provides support for internal components and EMI cage  
Rugged.  
Material: Aluminum  
Designed for IP67  
Powder coated enclosure  
Front Bezel  
Material Aluminum  
Color: Black  
Connectors and I/O  
Connector Location: To be located on the back of the monitor facing the rear unless otherwise noted.  
I/O connector LX1250TI  
Manufacture: Glenair; Mighty Mouse  
Part number: 801-011-07M13-37PA  
Description 37 pin, round  
Recommended Mating connector: 801-007-16M13-37SA  
LX1250TI User Manual  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Pin Description  
Pin  
23  
16  
25  
24  
11  
10  
12  
13  
Description  
RX2-  
Pin Description  
4
3
2
1
Audio in  
17  
20  
19  
34  
35  
36  
29  
33  
32  
22  
37  
Gnd Logic 4  
H plug detect  
+5 V DVI  
Audio out  
H- sync VGA  
V- sync VGA  
RX2+  
DVI VGA SCL  
DVI VGA SDA  
RX1-  
12 V power Backlight  
12 V power Logic  
GND Logic  
30 All-in-one  
31 All-in-one  
RX1 +  
26 USB - downstream  
27 USB + downstream  
RX0+  
GND Backlight  
USB -  
RX0-  
28 USB power downstream 9  
RXC-  
USB +  
21 USB gnd downstream  
18 VGA blue  
15  
RXC+  
USB power  
USB GND  
7
Gnd Logic 1  
Gnd Logic 2  
Gnd Logic 3  
6
8
VGA Green  
VGA red  
5
14  
5.7.1 I/O Connectors LX1251TI  
Power  
Manufacture: LTW  
Part number: LTWCD-07MMS-LC7001 and mating LTWCD-07BFFA-LL7001  
Description: 7 pin IP-68 rated, locking  
Reference Planar mating cable PN#:  
Or LTW Mating cable PN#  
VGA  
Manufacture: LTW  
Part number: LTWHDB-15PFFP-SA8001 and mating LTWHDB-15MMA-SL7001  
Description: HD-SUB 15 pin, IT-68 rated  
LX1250TI User Manual  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pin  
Description  
Pin  
5
Description  
GND  
Pin Description  
Power  
USB  
1
2
3
4
5
Blue-8-30VDC To Inverter  
Orange-Ground To Inverter  
Yellow-8-30VDC To Inverter  
Red-Bezel Switch Connector  
6
Red GND  
Green GND  
Blue GND  
+5 VDC  
5
4
3
2
1
Shield  
Black  
Green  
White  
Red  
7
8
9
Brown-Bezel Switch Connection  
No 2  
10  
S GND  
6
7
Green-8-30VDC To Video Board  
11  
12  
IDO  
White-Ground to Video Board  
VGA  
SDA DDC  
VGA  
13  
14  
15  
H Sync  
V Sync  
1
Red Video  
Green Video  
Blue Video  
RES  
2
SCL DDC  
3
4
USB  
Manufacture: LTW  
Part number: LTWUB-20PMFP-SC8002  
Description: USB, B TYPE, Female, IP-68 rated  
Physical Specifications  
Optical requirements  
Maximum luminance through touchscreen:  
650 cd/m2 (nits) typical  
Maximum luminance at full dimming  
Less than 5 nits.  
Uniformity  
Per LCD spec at full brightness. Maximum/Minimum 1.25 T typical  
Measured: Non-uniformity for white screen is 26% defined as = (1 min / max)  
Contrast  
Per LCD Spec and standard indoor brightness  
Measured: 600 typical, min = 300  
High ambient contrast  
Per Mil-Std-85762A Greater than 7:1 at 8000 fc  
Measured: CR = or > 11:1 with daylight (diffused) at 8,000 fC. CR = or> 3.5 for glare source of 2000 fL.  
(measured at 30° to normal)  
Voltage Range  
8 to 32 V, 12 V nominal.  
LX1250TI User Manual  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Voltage Transients  
Protected against voltage transients above +/-30V for 100ms  
Reverse polarity protection  
The display shall have reverse polarity protection as long as there is a slow blow fuse for power  
12 V use fuse 2A  
24 V use fuse 1A  
Maximum Power Consumption  
Maximum: <10 W @ 12 or 24V  
Typical power consumption: 7.7W @ 12 or 24V  
Power consumption in standby Power (LED amber)  
2.5 W @ 12 or 24V typical.  
Mechanical Outline  
Preliminary dimensions  
Figure 2: Outline Drawing  
LX1250TI User Manual  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
VESA Mount  
A VESA mount feature must be included on the LX1250TI, located on the back cover.  
Standard 100 and 75 mm VESA mount M4 x .7 threaded hole pattern. The holes shall be blind.  
Additional M4 threaded mounting or cable management locations on rear of display also included to  
support vertical cable routing.  
See Figure 2: Outline Drawing.  
Weight  
Weight <5.5lbs.  
Shipping Box  
Conforms to ISTA-2A (32 inch drop)  
Maintenance Requirements/Service Support  
Service Requirements  
The LX1250TI requires no routine maintenance.  
Service BOM  
Service BOM provided on request.  
Environmental Specifications  
Temperature  
Operating Temperature  
Storage Temperature  
Operating Survival Temp Range  
-20° C to + 60° C (-4° to 140° F)  
-20° C to + 85° C (-4° to 185° F)  
-40° C to + 70° C  
Humidity  
Operating:  
MIL-STD-810F (95% RH with 20° to 60° C temperature cycle for 11 days)  
Altitude  
Operating:  
Non-operating:  
15K ft (IEC 60068 PT2-13, 4hr)  
30K ft (IEC 60068 PT2-13, 4 hr)  
Vibration  
Note: Tests performed with assemblies mounted in a rigid retaining fixture.  
Operating ( Random):  
per axis  
10-500 Hz, 3.0G rms acceleration, 3 hours  
Vibration, Endurance Sine Sweep  
100-1100 Hz, 4 Gs rms, 1hr/axis  
Shock  
Note: Tests performed with monitor mounded in a rigid retaining assembly.  
Operating/Non-operating: 50 g, 11 ms duration, ½ sine, 3 shocks per axis (IEC 60068 PT2-27)  
LX1250TI User Manual  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
Regulatory Compliance  
Electromagnetic Compatibility (EMC)  
Must be verified to comply with the following:  
Emissions  
47 CFR. Part 15, Subpart B, Class A  
CE EMC Directive 2004/108/EC  
EN55022:2006, A1:2000, Class A  
EN61000-3-2:2006 Harmonic Current Emissions  
EN610003-3-3: 1995+ A1:2001 Voltage Flicker  
EN61000-3-3:1995+A1:2001+A2:2005  
Immunity Characteristics  
EN55024: 1998 + A1:2001 + A2:2003  
IEC 61000-4-2: 2008 ESD , 6kV contact and 8 kV air discharge  
IEC 61000-4-3: 2006+A1:2007 Radiated Field Immunity  
IEC 61000-4-4: 2004 - Electrical Fast Transient/Burst Immunity Test  
IEC 61000-4-5: 2005 - Surge immunity test  
IEC 61000-4-6:2008 - Immunity to conducted disturbances, induced by radio-frequency fields  
IEC 61000-4-8:2001 - Power frequency magnetic field immunity test  
IEC 61000-4-11:2004 Voltage Dips, Short Interruptions and Voltage Variations Immunity Tests  
Safety  
Must be certified to comply with the following:  
IEC/EN 60950-1:2005 Second Edition with country deviations for the US (UL60950-1) and  
Canada (CAN/CSA-C22.2 No. 60950-1)  
Designed to but not certified for Class 1 Div 2  
Designed and tested to IP67  
RoHS Compliance  
Planar guarantees RoHS compliance with on all part numbers ending in LF.  
WEEE compliance  
Will comply  
LX1250TI User Manual  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Reliability  
The MTBF of the LX1250TI shall be 30,000 hours at 25°C demonstrated by test or calculation, excluding  
brightness degradation.  
Included in the Shipping Box  
LX01250TI touch monitor  
Shipping Configuration (State of monitor when shipped)  
The unit will be shipped in the ‘ON’ state  
Brightness Control: Set to Maximum  
Product accessories  
Upon customer request  
LX1250TI User Manual  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Product Specifications Overview  
5
LCD Active Matrix Flat Panel Display  
(TFT)  
Display Type  
Viewable Size  
12.1 inch  
Display Viewing Area  
Display Color  
246 (W) x 184 (H) mm  
262 K (6 bit/color)  
Touchscreen Type  
Touchscreen Interface  
Touchscreen surface  
Contrast Ratio (Typical)  
IR touch  
USB  
strengthened glass with AntiGlare  
600:1  
Viewing Angle (Typical) @contrast ratio  
>10:1  
70° -70 ° H /60 ° -60° V  
Response Time (Typical)  
Brightness (Typical)  
Display Resolution  
Refresh Rate  
25 ms  
650 cd/m² Min  
XGA  
60 to 68 Hz  
12.5” W x 10” H x 2.3” D (no  
connectors)  
Preliminary Dimensions  
Preliminary Display Weight  
Audio input  
<5.5lbs, 2.5kg  
Mono 0-1VPP (LX1250TI only)  
37 pin Military connector  
None provided  
External Connections  
Power Supply  
Power Requirements  
Power Consumption  
8-32 V DC  
<8W typ @ 12V  
Built-in 75 and 100 mm VESA on  
monitor back  
VESA Compatible/Location  
Protective cover glass  
Meets 80-50 (scratch dig) per MIL-  
PRF-13830B.  
LX1250TI User Manual  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
020-1121-00 A  
LX1250TI User Manual  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Stereo Equalizer PV 215 EQ User Manual
Philips Flat Panel Television PT8508 User Manual
Philips Headphones SHB9150 User Manual
Philips MP3 Player SA9345 00 User Manual
Philips Satellite TV System MNT410F User Manual
Pinnacle Design TV Video Accessories TR4676FL User Manual
Pioneer DVD Recorder DVR 433H S User Manual
Polk Audio Speaker AB755c User Manual
Premier Mounts Indoor Furnishings INW AM200 User Manual
ProForm Home Gym PFSY74490 User Manual