Audio Multi-channel Receiver SX-LX03
Speaker System
SSP-LX03
Blu-ray Disc Home Cinema System
Audio Multi-channel Receiver
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified
service personnel.
IMPORTANT: THE MOULDED PLUG
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the
fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark
or the BSI mark
on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug
must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.
If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of
safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Blue : Neutral Brown : Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows ;
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
D3-4-2-1-2-2_B_En
Information for users on collection and disposal of old equipment and used batteries
Symbol for
equipment
These symbols on the products, packaging, and/or accompanying documents mean that
used electrical and electronic products and batteries should not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points in accordance with your national legislation.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
Symbol examples
for batteries
For more information about collection and recycling of old products and batteries, please
contact your local municipality, your waste disposal service or the point of sale where you
purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
Pb
If you wish to discard these items, please contact your local authorities or dealer and ask
for the correct method of disposal.
K058_B_En
POWER-CORD CAUTION
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement. S002_En
requires repair will be charged for even during the
warranty period.
K041_En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section One
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model
properly. After you have finished reading the instructions, put them in a safe place for future reference
.
Contents
Section One
03 Connecting up
Basic connections . . . . . . . . . . . . . . . . . . 26
What’s in the box. . . . . . . . . . . . . . . . . . . . .6
04 Getting started
Using the Auto MCACC setup for optimal
01 Controls and displays
Remote control . . . . . . . . . . . . . . . . . . . . . .7
Putting the batteries in
surround sound . . . . . . . . . . . . . . . . . . . . 29
05 Listening to your system
the remote control. . . . . . . . . . . . . . . . . . .9
Using the remote control. . . . . . . . . . . . . .9
Receiver. . . . . . . . . . . . . . . . . . . . . . . . . . .10
Front panel . . . . . . . . . . . . . . . . . . . . . . .10
Display . . . . . . . . . . . . . . . . . . . . . . . . . .11
Rear panel. . . . . . . . . . . . . . . . . . . . . . . .13
Blu-ray disc player . . . . . . . . . . . . . . . . . . .14
Front Panel . . . . . . . . . . . . . . . . . . . . . . .14
Display . . . . . . . . . . . . . . . . . . . . . . . . . .14
Rear Panel . . . . . . . . . . . . . . . . . . . . . . .15
Auto listening mode . . . . . . . . . . . . . . . . . 31
Listening in surround sound . . . . . . . . . . . 31
Dolby Pro Logic II Music settings . . . . . . 32
Using Advanced Surround . . . . . . . . . . . . 32
Using Front Stage Surround Advance. . . . 33
Listening in stereo. . . . . . . . . . . . . . . . . . . 33
Listening with headphones . . . . . . . . . . . . 33
Using the Sound Retriever . . . . . . . . . . . . 33
Listening with Acoustic Calibration EQ . . . 34
Enhancing dialogue . . . . . . . . . . . . . . . . . 34
Using Midnight and Quiet listening modes . 34
Adjusting the bass and treble . . . . . . . . . . 35
Boosting the bass level . . . . . . . . . . . . . . . 35
Adjusting sound delay. . . . . . . . . . . . . . . . 35
02 Speaker Setup Guide (LX03BD)
Safety precautions when setting up. . . . . .16
Home theater sound setup . . . . . . . . . . . .16
Standard surround setup . . . . . . . . . . . .16
Front surround setup. . . . . . . . . . . . . . . .16
Preparing the speakers . . . . . . . . . . . . . . .17
Using the supplied speaker stands . . . . .18
Wall mounting the speakers . . . . . . . . . .19
Additional notes on speaker placement .19
Connect the speakers . . . . . . . . . . . . . . . .20
Using your own speaker cables. . . . . . . .22
06 Connecting an iPod
Connecting your iPod to this unit . . . . . . . 36
iPod playback . . . . . . . . . . . . . . . . . . . . . 36
07 Listening to the radio
Listening to the radio . . . . . . . . . . . . . . . . 39
Improving poor FM reception . . . . . . . . . 39
Improving poor AM sound . . . . . . . . . . . 39
Changing the noise cut mode. . . . . . . . . 40
Memorizing stations . . . . . . . . . . . . . . . . 40
Listening to station presets. . . . . . . . . . . 40
Using RDS . . . . . . . . . . . . . . . . . . . . . . . . 41
Displaying RDS information . . . . . . . . . . 41
Searching for RDS programs . . . . . . . . . 41
02 Speaker Setup Guide (SX-LX08)
Safety precautions when setting up. . . . . .24
Home theater sound setup . . . . . . . . . . . .24
Connect the speakers . . . . . . . . . . . . . . . .24
4
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section One
08 Surround sound settings
11 Additional information
Using the Sound Setup menu . . . . . . . . . 42
Effective Sound (for optimum sound) . . 42
Channel level setting . . . . . . . . . . . . . . . 43
Speaker distance setting . . . . . . . . . . . . 43
Dynamic Range Control. . . . . . . . . . . . . 44
Dual mono setting . . . . . . . . . . . . . . . . . 44
Virtual Surround Back . . . . . . . . . . . . . . 44
LFE Attenuate . . . . . . . . . . . . . . . . . . . . 45
DTS CD setting . . . . . . . . . . . . . . . . . . . 45
Optional system settings . . . . . . . . . . . . . .56
Setting the sleep timer . . . . . . . . . . . . . .56
Dimming the display. . . . . . . . . . . . . . . .56
Changing the display mode. . . . . . . . . . .57
Key lock setting. . . . . . . . . . . . . . . . . . . .57
Setting up the remote to control your TV . .57
TV Preset code list. . . . . . . . . . . . . . . . . .58
Surround sound formats . . . . . . . . . . . . . .58
Dolby. . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Dolby Digital . . . . . . . . . . . . . . . . . . . . . .58
Dolby Pro Logic II and Dolby Surround . .58
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
DTS Digital Surround . . . . . . . . . . . . . . .59
Installation and maintenance . . . . . . . . . .59
Hints on installation . . . . . . . . . . . . . . . .59
Troubleshooting. . . . . . . . . . . . . . . . . . . . .60
General . . . . . . . . . . . . . . . . . . . . . . . . . .60
Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . .62
HDMI connection . . . . . . . . . . . . . . . . . .62
Front panel display messages . . . . . . . . .62
Resetting the system . . . . . . . . . . . . . . . . .64
Specifications (LX03BD model) . . . . . . . . .65
Specifications (SX-LX08 model) . . . . . . . . .66
09 Other connections
Using this unit for TV audio . . . . . . . . . . . 46
Audio input settings from the TVs
(TV Input) . . . . . . . . . . . . . . . . . . . . . . . . 46
Listening to the sound of an external
device on this receiver . . . . . . . . . . . . . . . 47
Connecting for digital audio. . . . . . . . . . 47
Connecting an analog audio
component . . . . . . . . . . . . . . . . . . . . . . 47
Listening to an external audio source . . 47
Outputting the sound of this receiver to
an external device . . . . . . . . . . . . . . . . . . 48
Line Output setting . . . . . . . . . . . . . . . . 48
Connecting external antennas . . . . . . . . . 49
About control out connections. . . . . . . . . 49
Connecting using HDMI . . . . . . . . . . . . . 50
Switching the HDMI audio setting. . . . . 51
Setting the Auto Delay. . . . . . . . . . . . . . 51
Resetting the HDMI connection. . . . . . . 52
About HDMI . . . . . . . . . . . . . . . . . . . . . 52
Section Two
Operating instructions for Blu-ray
disc player (BDP-LX08). . . . . . . . . 68
10 HDMI Control
Making the HDMI Control connections . . 53
Setting the HDMI options. . . . . . . . . . . . . 55
Setting the HDMI Control mode. . . . . . . 55
Before using synchronization. . . . . . . . . . 55
Synchronized amp mode . . . . . . . . . . . . . 55
Synchronized amp mode operations . . . 55
Canceling synchronized amp mode. . . . 55
5
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section One
What’s in the box
Please confirm that the following items are all supplied.
LX03BD model
SX-LX08 model
• Remote control
Receiver box:
• Remote control
• AA/R6 dry cell batteries (to confirm system
operation) x2
• AA/R6 dry cell batteries (to confirm system
operation) x2
• AM loop antenna
• AM loop antenna
• FM antenna
• FM antenna
• Microphone (for Auto MCACC setup)
• Power cords x2
• Microphone (for Auto MCACC setup)
• Power cords x2
• HDMI cables x2
• HDMI cables x2
• Speaker cable adaptors x5
• Cleaning cloth*
• Speaker cable adaptors x5
• Cleaning cloth*
• Warranty card
• Warranty card
• Setup Guide
• Setup Guide
• These operating instructions
• These operating instructions
Speakers box:
• Speakers (front x2, center x2, surround x2)
• Subwoofer
• Speaker cables x7
• Brackets x2
• Screws (for brackets) x4
• Speaker stands x2
• Non-skid pads (for satellite speakers) x24
• Non-skid pads (for subwoofer) x4
• Non-skid pads (for speaker stands) x8
• Spiral wrap x2
*When cleaning the cabinet, use the provided cleaning cloth.
Do not allow alcohol, thinner, benzene, or insecticides to come into contact with the surface, since
finish discoloration may occur.
6
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
01
CChaoptnert1rols and displays
Remote control
• Remote control unit buttons indicated with
RECEIVER
BD
blue lettering (buttons indicated with
asterisk (*) in this section) are used to
operate an optional Pioneer Blu-ray disc
player. Set the remote control operation
selector switch to BD to perform such
operations.
1
3
4
2
5
1/2
HDMI
iPod
TV
LINE
FM/AM
TUNER
SOUND
SURROUND ADV SURR RETRIEVER
1
RECEIVER
1
4
2
5
8
0
3
Switches the receiver on or into standby.
6
6
8
2
BD
7
9
Switches the Blu-ray disc player on or into
standby.
FL DIMMER
CLEAR
7
9
TV CONTROL
VOLUME
3
Input select buttons
CH
VOL
Use to select an input source.
INPUT
TUNE
MUTE
See the section Audio input settings from the
TVs (TV Input) on page 46 for information
regarding the TV button.
10
12
TOP MENU
SETUP
11
13
TOOLS
ST
4
Sound controls
ST
ENTER
TUNE
SURROUND
Selects a Surround mode (page 31) or
switches to stereo playback (page 33).
HOME
MENU
RETURN
MCACC
15
18
19
14
CLASS
T.EDIT
SOUND
16
17
ADV SURR
Selects a Pioneer original surround mode
(page 32).
HOME MEDIA OUTPUT
VIDEO
POPUP
MENU
GALLERY RESOLUTION SELECT
/
/
20
5
SOUND RETRIEVER
Press to restore CD quality sound to
compressed audio sources (page 33).
21
22
24
iPod
CTRL
DISPLAY
23
6
Number buttons
AUDIO SUBTITLE ANGLE
Use to enter a track number or radio station.
RECEIVER
iPod
BD
7
FL DIMMER*
Press to switch the brightness of the Blu-ray
disc player’s display. The FL OFF indicator
lights when Off is selected.
7
En
Download from Www.Somanuals.com. All Manuals Search And Download.
01
Controls and displays
8
TV CONTROL buttons
18 SOUND
Accesses the sound menu to adjust the
These control Pioneer Flat Screen TVs.
tone, bass and treble, etc. (page 32, 34).
9
VOLUME +/–
Adjusts the volume.
VIDEO SELECT*
Press to switch the player’s terminal from
which the video signals are output. Use to
switch between digital output (HDMI OUT
terminal) and analog output
10 MUTE
Mutes the sound (press again to cancel).
11 TOP MENU
(COMPONENT VIDEO, S-VIDEO or VIDEO
output terminals) (the signals are only
output from the selected video output
terminal).
Press to return to the iPod Top menu when
using iPod functions.
After set the remote control operation switch to
BD, press to displays the player’s top menu of
a BD-ROM, or DVD-Video disc.
19 MCACC
Starts the Auto MCACC setup (page 29).
12 SETUP
Use to make various system and surround
sound settings (page 42, 51, 56).
POPUP MENU*
Press to display the BD-ROM or DVD-Video
menus.
TOOLS*
Press to display/hide the TOOLS menu.
20 Playback controls
See iPod playback on page 36 and Playing discs
or files on page 90 for an explanation of these
controls.
13 /// (TUNE +/–, ST +/–), ENTER
Use to select/switch system settings and
modes, and to confirm actions.
21 Color (red/green/yellow/blue) buttons
Use these to navigate BD-ROM menus.
Use TUNE +/– to find radio frequencies and
use ST +/– to find preset stations.
22 iPod controls:
14 HOME MENU*
Press to display/hide the Home Menu.
CTRL
Switches between the iPod controls and
the receiver controls.
15 RETURN
Press to return to the previous screen.
16 CLASS
Changes repeat play setting.
Changes shuffle play setting.
Switches between the three banks
(classes) of radio station presets (page 40).
HOME MEDIA GALLERY*
Press to display/hide the Home Media
Gallery screen.
BD/DVD controls:
AUDIO*
17 T.EDIT
Press to switch the audio streams/
channels.
Memorizes stations for recall (page 40).
OUTPUT RESOLUTION*
SUBTITLE*
Use to switch the output video resolution
from the player’s HDMI OUT or
COMPONENT VIDEO output terminals.
Press to switch the subtitles.
8
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
01
ANGLE*
• Remove batteries from equipment that
isn’t going to be used for a month or more.
Press to switch the BD-ROM or DVD-Video
camera angles.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country/area.
23 DISPLAY
Displays RDS information (page 41).
Displays song playback information when
using the iPod function.
• Do not use or store batteries in direct
sunlight or other excessively hot place,
such as inside a car or near a heater. This
can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the
life or performance of batteries.
After set the remote control operation switch to
BD, press to display the disc information.
24 Remote control operation selector switch
Set to RECEIVER iPod to operate this system or
iPod, BD to operate the Blu-ray disc player.
Using the remote control
Please keep in mind the following when using
the remote control:
Putting the batteries in the remote
control
• Make sure that there are no obstacles
between the remote and the remote sensor
on the unit.
• Remote operation may become unreliable
if strong sunlight or fluorescent light is
shining on the unit’s remote sensor.
1
Open the battery compartment cover
• Remote controllers for different devices
can interfere with each other. Avoid using
remotes for other equipment located close
to this unit.
on the back of the remote control.
2
Insert two AA/R6 batteries into the
battery compartment following the
indications (, ) inside the compartment.
• Replace the batteries when you notice a
fall off in the operating range of the remote.
3
Close the cover.
• Use within the operating range in front of
the remote control sensor on the display
unit, as shown.
Caution
Incorrect use of batteries can result in hazards
such as leakage and bursting. Please observe
the following:
PULL OPEN
E R
R
T
I E
E
V
R
D N
S O U
HD
MI
• Don’t mix new and old batteries together.
• Don’t use different kinds of battery
together — although they may look similar,
different batteries may have different
voltages.
30
30
7 m
• Make sure that the plus and minus ends of
each battery match the indications in the
battery compartment.
9
En
Download from Www.Somanuals.com. All Manuals Search And Download.
01
Controls and displays
Receiver
Front panel
INP
9
10
PULL OPEN
STANDB
Y/ON
HDMI
INPUT
SURROUND
ADVANCED
VOLUME
iPod DIRECT
PHONES
MCACC
STANDBY/ON
HDMI
1
2
3
4
5
6
7
8
• Open the front door flap when using the
front panel connectors.
6
IR remote sensor
7
Front panel display
1
STANDBY/ON
See Display below for details.
Switches the system on or into standby.
8
Motion sensor
2
HDMI indicator (Red)
When the front panel display is off, if Display
Mode is set to Auto Display, the display will
automatically turn on when movement is
detected by the motion sensor (page 57).
Lights when this system is connected to HDMI
(HDCP) compatible component.
Also lights during initialization, after you plug
this unit into an AC outlet.
9
Action indicator
Lights when a touch sensor operation is
performed.
3
iPod DIRECT terminal
Use to connect your Apple iPod as an audio
source for playback (page 36).
4
PHONES jack
Connect headphones.
5
MCACC jack
Use to connect the supplied microphone for
the Auto MCACC setup (page 29).
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
01
10 Touch sensor
Touch sensor is on top of the unit.
Using the motion sensor
This system features a motion sensor. Install it
in a location that will able to sense the
movement of people near by.
Lightly touch the displayed words or symbols to
operate controls.
The motion sensor detects movement in the
left/right and up/down directions within a
distance of 2.5 m and an angle of 40º (20º only
in the upper direction). Walking towards the
unit will reduce the sensing range to 0.7 m.
INPUT
Selects the source you want to listen to
(
Digital 1 to Digital 3, Analog, iPod,
HDMI 1 or HDMI 2).
SURROUND
PULL OPEN
Selects a Surround mode (page 31) or
switches to stereo playback (page 33).
R
E
I E
R
V
T
E
R
D
N
U
S
O
HD
MI
ADVANCED
Selects a Pioneer original surround mode
(page 32).
40
VOLUME +/–
20
Use to adjust the volume.
40
2.5 m
40
Display
1
2
3
4
5
DIRECT STEREO
ADVSURR F.S.SURR
2DAAC
2PL
PCM
DTS
BASS MODE TONE V.SB L.OUT
ALC S.RTRV DIALOG
MCACC
A
B
C
I
6
7
8
9
1
DIRECT
ADV SURR
Lights when Direct Sound is selected (i.e.
Effective Sound is off) (page 42).
Lights when one of the Advanced Surround
listening modes is selected (page 32).
2
Listening mode indicators
F.S.SURR
Lights when one of the Front Stage
Surround Advance listening modes is
selected (page 33).
STEREO
Lights when the Stereo mode is selected or
when a stereo source is being played back
in the Auto listening mode (page 31).
11
En
Download from Www.Somanuals.com. All Manuals Search And Download.
01
Controls and displays
3
Digital format indicators
6
iPod indicators
2 D
Lights during playback of a Dolby Digital
source (page 31).
Lights during playback, and flashes during
pause mode.
2 PLII
Lights during Dolby Pro Logic II decoding
(page 32).
Lights during shuffle play.
Lights during repeat play.
PCM
Lights during playback of PCM signals.
DTS
Lights during 1-track repeat play.
Character display
Lights during playback of a DTS source
(page 31).
7
8
4
Sound processing indicators
Tuner indicators
BASS MODE
Lights when Bass Mode is active (page 35).
Lights when a broadcast is being received.
TONE
Lights when any of the Midnight, Quiet or
tone controls feature is selected (page 35).
Lights when a stereo FM broadcast is being
received in auto stereo mode.
V.SB
Lights when Virtual Surround Back mode
is active (page 44).
Lights when FM mono reception is
selected.
L.OUT
Lights when Line Output is set to Lt/Rt
(page 48).
Lights when in one of the RDS display or
search modes.
ALC
A, B, C
Lights when listening mode is set to A.L.C.
Indicate the class of tuner function.
(page 31).
S.RTRV
9
Lights when Sound Retriever is active
(page 33).
Lights when sleep timer is active (page 56).
DIALOG
Lights when Dialogue Enhancement is
active (page 34).
5
MCACC
Lights when Acoustic Calibration EQ is active
(page 34).
Blinks during Auto MCACC Setup (page 29).
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
01
Rear panel
1
2
3
4
5
6
7
8
9
10 11
ANALOG
L
IN
OUT
CONTROL
OPTICAL
FRONT
4
CENTER
4
R
R
L
ANALOG
L
1
2
AM
R
LOOP
AUDIO IN
COAX
FM
AC IN
UNBAL
75
R
ANTENNA
DIGITAL IN
SURROUND
8
SUB WOOFER
4
L
3
AUDIO OUT
OUT
IN 2
IN 1
SPEAKERS
DIGITAL IN
HDMI
LX03BD
12
IN
OUT
CONTROL
FRONT
CENTER
R
R
L
ANALOG
L
PREOUT
AC IN
R
SURROUND
L
SUBWOOFER
AUDIO OUT
(
-
)
SPEAKERS
4
8
SX-LX08
1
2
AC IN – Power inlet
AUDIO OUT (ANALOG) jacks
7
HDMI OUT connector
Connect to a television that has an HDMI
terminal.
Connect to the other audio component.
8
HDMI IN1/2 connectors
3
CONTROL IN/OUT jacks
Use high-quality audio/video connection with
compatible HDMI devices. Connect the Blu-ray
disc player to HDMI IN 1.
Use to connect other Pioneer components so
that you can control all your equipment from a
single IR remote sensor.
To select this input, choose HDMI 1 or HDMI 2
.
4
SPEAKERS terminals
9
DIGITAL IN1/2 (OPTICAL) jacks
Match the colors of the speaker cables to their
respective connectors.
To listen to optical digital audio, change the
input to Digital 1 or Digital 2.
5
AUDIO IN (ANALOG) jacks
10 AM LOOP antenna terminal
11 FM antenna socket
Handle sound from an external component by
using stereo audio cable. To listen to analog
audio, change the input to Analog.
12 SUBWOOFER PREOUT jack (SX-LX08 model
only)
Use the RCA plug cable furnished with the
speaker system (or commercial alternative) to
connect a powered subwoofer.
6
DIGITAL IN3 (COAX) jack
To listen to coaxial digital audio, change the
input to Digital 3 COAX.
13
En
Download from Www.Somanuals.com. All Manuals Search And Download.
01
Controls and displays
Blu-ray disc player
Front Panel
(Controls hidden behind the front panel door)
2
3
4
5
6
1
9
8
7
1
STANDBY/ON
4
5
Disc tray
Press to turn the power on and off.
FL OFF indicator
2
Remote control sensor
This lights when Off is selected with FL
Point the remote control to this, then operate it
within approximately 7 m.
DIMMER.
6
Front panel display
The player may have trouble capturing remote
control signals if there is a fluorescent light
nearby. If this happens, move the player away
from the fluorescent light.
7
STOP
Press to stop playback.
8
PLAY
Press to start playback.
3
HDMI indicator
This lights when an HDMI-compatible device is
connected (page 76).
9
OPEN/CLOSE
Press to open and close the disc tray.
Display
1
2
3
PQLS
24HZ
CONTROL 50HZ
60HZ
6
5
4
1
3
PQLS
Lights during playback.
Lights when the PQLS function is activated
(page 78).
2
Caution: This system cannot use the PQLS
function.
Lights when playback is paused.
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and displays
01
4
Character display
6
CONTROL
Displays the title/chapter/track number,
elapsed time, etc.
Lights when the HDMI Control function is
activated (page 78).
5
24HZ/50HZ/60HZ
The frequency of the video frame or field being
output lights.
Rear Panel
1
2
3
4
FRONT
SURROUND SURROUND BACK CENTER
L
R
L
VIDEO OUT
VIDEO
AC IN
Y
R
SUB WOOFER
AUDIO OUT
(
2
ch
)
AUDIO OUT
(
7.1 ch
)
PB
HDMI OUT
PR
OPTICAL
CONTROL DIGITAL
IN OUT
COMPONENT
VIDEO
S-VIDEO
7
6
5
1
AUDIO OUT (2 ch) terminals
7
CONTROL IN terminal
Connect with the audio input terminals on a TV
or tape recorder, etc.
Use to control this player from the remote
sensor of another Pioneer component with a
CONTROL OUT terminal and bearing the
mark. Connect the CONTROL OUT of the other
component to the CONTROL IN of this player
using a mini-plug cord.
2
AUDIO OUT (7.1 ch) terminals
Connect with the 7.1 channel audio input
terminals on an AV receiver or amplifier, etc.
3
VIDEO OUT terminals
VIDEO – Connect with the video input
terminal on a TV.
Caution
• Be sure to connect cables for outputting the
audio and video signals (pages 76 and 80).
S-VIDEO – Connect with the S-Video input
terminal on a TV.
• When connected via System Control, point
the remote control toward the connected
component. The remote will not work
correctly when pointed at this player.
COMPONENT VIDEO – Connect with the
component video input terminals on a TV.
4
AC IN
Connect the power cord here.
• You cannot use System Control with
components that do not have a System
Control terminal or with components
manufactured by companies other than
Pioneer.
5
HDMI OUT terminal
Connect to the HDMI IN 1 jack of the receiver
with the supplied HDMI cable.
6
DIGITAL OUT (OPTICAL)
Connect with the digital audio input terminal
on the other audio component.
15
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Speaker Setup Guide (LX03BD)
CShpapetera2ker Setup Guide (LX03BD)
Front surround setup
Safety precautions when
This setup is ideal when rear surround speaker
placement isn’t possible or you want to avoid
running long speaker cables in your listening
area. The surround left and right speakers
should be about 1.5 m apart.
setting up
When assembling the speakers, lay them down
flat on their side to avoid accidents or injury.
Make sure to use a stable surface when
assembling, setting up, and placing the
speakers.
Front Surround
Front
left
Surround
left
right
right
Center
If the speakers are to be used in a stacked
configuration, always use the provided
brackets to secure them together (page 17).
Center
Subwoofer
Home theater sound setup
Depending on the size and characteristics of
your room, you can place your speakers in one
of two ways using this system.
Listening position
*When center speakers are placed in the center.
FL
FR
Standard surround setup
This is a standard multichannel surround sound
speaker setup for optimal 5.1 channel home
theater sound. The front left and right speakers
should be about 1.8 m to 2.7 m apart.
SR
SL
C
Front
left
Front
right
Center
Subwoofer
Surround
left
Surround
right
Listening position
*When center speakers are placed in the center.
FL FR
FR
C
16
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup Guide (LX03BD)
Preparing the speakers
02
As shown in the illustration, stack the
speakers. Align the brackets with the screw
holes on the back of the two speakers, and use
the two screws to fix in place.
1
Attach the non-skid pads to the base of
each speaker (as shown).
Use the adhesive side of the pads to attach
them to the base (flat surface) of each speaker.
Standard surround setup:
Left
Right
Red
Non-skid pads
(for satellite
speakers)
Front
speaker
White
Center
speaker
Green
Green
Front
speaker
Front
speaker
Center
speaker
Surround
speaker
Bracket
Center
speaker
Non-skid pads
(for subwoofer)
Screw
Subwoofer
(When mounting center speakers to right
2
and left) Stack the speakers and fix with the
bracket.
Each speaker is provided with a color-coded
indicator on the label on the rear side to assist
identification. Refer to the color indicators and
install the speakers correctly.
Color indicator
17
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Speaker Setup Guide (LX03BD)
Front surround setup:
Using the supplied speaker stands
When setting up the front surround, the
supplied accessory speaker stand can be used.
Apply the non-skid pads (for speaker stand) to
the four corners of the speaker stand and set
the speakers on the stand.
Left
Right
Grey
Surround
speaker
Blue
Center
speaker
Green
Green
Non-skid pads
(for speaker stands)
Speaker stand
Surround
speaker
Bracket
Center
speaker
Screw
Caution
• Do not attempt to carry the speakers when
they are connected with the bracket. Doing
so may cause damage to the bracket or
worsen damage to the bracket and
speakers in the event they are dropped.
3
Connect the speaker system.
Refer to Connecting up on page 26 to connect
the speakers properly. After connecting
everything, place the speakers as shown in the
diagram above for optimal surround sound.
After placing the speakers, run the Auto
MCACC setup (page 29) to complete your
surround sound setup.
18
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup Guide (LX03BD)
02
Wall mounting the speakers
The front, center and surround speakers have a
mounting hole which can be used to mount the
speaker on the wall.
Additional notes on speaker
placement
• Install the main front left and right
speakers at an equal distance from the TV.
• When using the Standard surround setup,
install the surround speakers slightly
above ear level for optimum effect.
Before mounting
• Remember that the speaker system is
heavy and that its weight could cause the
screws to work loose, or the wall material to
fail to support it, resulting in the speaker
falling. Make sure that the wall you intend
to mount the speakers on is strong enough
to support them. Do not mount on plywood
or soft surface walls.
Precautions:
• When installing the center speaker on top
of the TV, be sure to secure it with tape or
some other suitable means. Otherwise, the
speaker may fall from the TV due to
external shocks such as earthquakes,
endangering those nearby or damaging
the speaker.
• Mounting screws are not supplied. Use
screws suitable for the wall material and
support the weight of the speaker.
• The front, center and surround speakers
supplied with this system are magnetically
shielded. However, depending on the
installation location, color distortion may
occur if the speaker is installed extremely
close to the screen of a television set. If this
case happens, turn the power switch of the
television set OFF, and turn it ON after 15
min. to 30 min. If the problem persists,
place the speaker system away from the
television set.
Caution
• If you are unsure of the qualities and
strength of the wall, consult a professional
for advice.
• Pioneer is not responsible for any
accidents or damage that result from
improper installation.
• The subwoofer is not magnetically shielded
and so should not be placed near a TV or
monitor. Magnetic storage media (such as
floppy discs and tape or video cassettes)
should also not be kept close to the
subwoofer.
5
mm
10 mm
• Do not attach the subwoofer to the wall or
ceiling. They may fall off and cause injury.
Mounting screw
(not supplied)
6
mm to 8 mm
19
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Speaker Setup Guide (LX03BD)
Connect the speakers
ANALOG
IN
OUT
CONTROL
L
FRONT
4
CENTER
4
R
L
ANALOG
L
R
AUDIO IN
R
SURROUND
8
SUB WOOFER
4
R
L
COAX
3
AUDIO OUT
SPEAKERS
DIGITAL IN
Front right
Subwoofer
(Purple)
Front left
(White)
Center
(Green)
(Red)
Surround left
Surround right
(Blue)
(Grey)
Listening position
Important
WARNING
• When connecting this system or changing
connections, be sure to switch power off
and disconnect the power cord from the
wall socket.
After completing all connections, connect
the power cords to the wall socket.
• Pioneer bears no responsibility for
accidents resulting from faulty assembly or
installation, insufficient mounting strength
of walls, mounting fixtures (or other
building fixtures), misuse or natural
disasters.
20
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup Guide (LX03BD)
02
• You may purchase and use your own
speaker cables if desired. For details, see
Using your own speaker cables on page 22.
• When connecting the center speakers,
connect the Y-cable dual end to the two
center speakers in the same way.
• The front and surround speaker cables
have a color-coded connector at one end
and two bare wires at the other end.
• Two purple cables are provided for the
subwoofer, one 4 meters and the other 10
meters in length. Use the appropriate cord
depending on the length needed for the
installation location.
Y-cable
Color-coded wire
(Connect to speaker)
To receiver
• Connect the other end to the color-coded
speaker terminals on the rear of the
receiver. Make sure to insert completely.
Color-coded connector
(Connect to rear panel)
The small lug at the wire-end of the speaker
plug should face up or down depending on
whether it’s being plugged into one of the
upper or lower speaker terminals. Please
make sure to connect correctly.
• Since there is only one terminal to connect
the two center speakers, you will need to
use the supplied Y-cable for the connection.
• Twist and pull off the protective shields on
each wire.
Upper terminal
Lower terminal
• Connect the wires to the speaker. Each
speaker in the illustration can be identified
by means of the color-coded indicator
provided on the rear-surface label.
Match the color-coded wire with the color
indicator on the label, then insert the color-
coded wire into the red (+) side and the
other wire into the black (–) side.
• Fasten the cables together with the spiral
wrap.
Hold multiple cables together and place
the wrap over the cables from the end.
Wrap the spiral wrap with the cables in the
center.
The spiral wrap may be cut at a desired
length.
Black (–) Red (+)
Color-coded wire
21
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Speaker Setup Guide (LX03BD)
Using your own speaker cables
When connecting the speakers, you can
purchase and use your own speaker cables if
desired, in place of those furnished. In this
case, perform the following procedures to
attach the speaker cable adaptor to your own
Caution
• These speaker terminals carry
HAZARDOUS LIVE voltage. To prevent
the risk of electric shock when connecting
or disconnecting the speaker cables,
disconnect the power cord before touching
any uninsulated parts.
1
cables:
•
While holding down the two buttons on
• Do not connect any speakers other than
those supplied to this system.
the adaptor, insert the wire ends of your own
cable into the adaptor.
• Do not connect the supplied speakers to
any amplifier other than the one supplied
with this system. Connection to any other
amplifier may result in malfunction or fire.
Separately purchased
speaker cable
• After connecting the plugs, pull lightly on
the cables to make sure that the ends of
the cables are securely connected to the
terminals. Poor connections can create
noise and interruptions on the sound.
• White, Red, Blue, Grey and Purple speaker
cable adaptors are provided as
accessories. Use these to attach your own
cables for the front left/right speakers,
surround left/right speakers and
subwoofer.
• If the cable’s wires happen to be pushed
out of the terminals, allowing the wires to
come into contact with each other, it
places an excessive additional load on the
amp. This may cause the amp to stop
functioning, and may even damage the
amp.
• Use the supplied Y- cable for center
speakers connections.
• Confirm the +/– polarities of the two wires
and the corresponding markings on the
adaptor, and be sure to insert the proper
wire core into the proper side.
• After inserting the wire cores, pull gently
on the cable to confirm that the wires do
not slip out.
• Be careful to prevent the cores of the two
wires from touching each other, since a
short circuit will result.
Note
1
Speaker cables can be of sizes between 0.3 sq and 1.0 sq (equivalent to 22 gauge and 17 gauge, respectively).
22
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup Guide (SX-LX08)
02
CShpapetera2ker Setup Guide (SX-LX08)
Red
IN
ANALOG
OUT
CONTROL
L
CENTER
FRONT
R
L
ANALOG
L
R
PREOUT
AUDIO IN
Green
R
SURROUND
R
L
COAX
3
AUDIO OUT
SUBWOOFER
(
-
)
SPEAKERS
4
8
DIGITAL IN
Grey
White
Blue
To line level
input
Front
right
Front
left
Center
Powered
Subwoofer
Surround
left
Surround
right
Listening position
Important
WARNING
• When connecting this system or changing
connections, be sure to switch power off
and disconnect the power cord from the
wall socket.
After completing all connections, connect
the power cords to the wall socket.
• Pioneer bears no responsibility for
accidents resulting from faulty assembly or
installation, insufficient mounting strength
of walls, mounting fixtures (or other
building fixtures), misuse or natural
disasters.
23
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Speaker Setup Guide (SX-LX08)
While holding down the two buttons on the
adaptor, insert the wire ends of speaker cable
into the adaptor.
Safety precautions when
setting up
• White, Red, Blue, Grey and Green speaker
cable adaptors are provided as
accessories. Use these to attach your own
cables for the front left/right speakers,
surround left/right speakers and center
speaker.
When assembling the speakers, lay them down
flat on their side to avoid accidents or injury.
Make sure to use a stable surface when
assembling, setting up, and placing the
speakers.
• The speaker cable adaptors are color-
coded to their matching speakers. Insert
the proper cable into its adapter of
designated color. Confirm the polarity (+/–)
indicated on the adaptor and cable, and
match the polarities properly.
Home theater sound setup
This is a standard multichannel surround sound
speaker setup for optimal 5.1 channel home
theater sound. The front left and right speakers
should be about 1.8 m to 2.7 m apart.
Front
left
Front
right
Speaker cable
Center
Powered
Subwoofer
Surround
left
Surround
right
Connect the speaker cable adaptors to the
color-coded speaker terminals on the rear of
the receiver. Make sure to insert completely.
Listening position
• The small lug at the wire-end of the speaker
plug should face up or down depending on
whether it’s being plugged into one of the
upper or lower speaker terminals. Please
make sure to connect correctly.
Connect the speakers
Attach one end of the speaker cable provided
with the speaker system (or a commercial
alternative) to the speaker cable adaptor
furnished as an accessory with this unit.
• When connecting the speakers, consult
the operating instructions provided with
the speaker system.
• This system is not provided with speaker
cables. Please purchase speaker cables
separately.
Upper terminal
Lower terminal
Connect the other end to speaker terminals on
the speaker system. Make sure to insert
completely.
Twist exposed wire strands together.
• Consult the operating instructions
provided with the speaker and confirm the
connection procedures.
10 mm
24
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Speaker Setup Guide (SX-LX08)
02
Connect the subwoofer.
• Use the RCA plug cable furnished with the
speaker system (or commercial alternative)
to connect the SUBWOOFER PREOUT
connector to the line level input connector
of the powered subwoofer.
Caution
• These speaker terminals carry
HAZARDOUS LIVE voltage. To prevent
the risk of electric shock when connecting
or disconnecting the speaker cables,
disconnect the power cord before touching
any uninsulated parts.
• Do not connect any speakers other than
those designated for this system.
• After connecting the plugs, pull lightly on
the cables to make sure that the ends of
the cables are securely connected to the
terminals. Poor connections can create
noise and interruptions on the sound.
• If the cable’s wires happen to be pushed
out of the terminals, allowing the wires to
come into contact with each other, it
places an excessive additional load on the
amp. This may cause the amp to stop
functioning, and may even damage the
amp.
25
En
Download from Www.Somanuals.com. All Manuals Search And Download.
03
Connecting up
CChoaptnern3 ecting up
Basic connections
• The following describes connections to a TV equipped with HDMI and optical digital audio
inputs.
TV
AM loop antenna
To
From optical
digital output
HDMI input
4
5
1
OPTICAL
1
2
AM
2
LOOP
FM antenna
FM
UNBAL
75
ANTENNA
DIGITAL IN
OUT
IN 2
IN 1
HDMI
Receiver
3
Blu-ray disc player
SURROUND SURROUND BACK CENTER
VIDEO OUT
AC IN
Y
VIDEO
SUB WOOFER
AUDIO OUT
(
7.1 ch
)
PB
HDMI OUT
PR
CAL
TAL
UT
COMPONENT
VIDEO
S-VIDEO
Important
WARNING
• When connecting this system or changing
connections, be sure to switch power off
and disconnect the power cord from the
wall socket.
After completing all connections, connect
the power cords to the wall socket.
• Pioneer bears no responsibility for
accidents resulting from faulty assembly or
installation, insufficient mounting strength
of walls, mounting fixtures (or other
building fixtures), misuse or natural
disasters.
26
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting up
03
1
Assemble the AM loop antenna.
3
Connect the Blu-ray disc player to the
receiver.
fig. c
fig. a
fig. b
Plug the HDMI cable into the HDMI IN 1 jack
on the rear of the receiver.
Plug the other end of the cable into the HDMI
OUT jack on the rear of the Blu-ray disc player.
4
Connect the receiver to your TV.
a. Bend the stand in the direction indicated by
the arrow.
Connect the HDMI OUT jack on receiver to an
HDMI input on your TV.
b. Clip the loop onto the stand.
• You can have audio from the receiver, as
well as audio and video from the Blu-ray
disc player, output to your TV by
c. If you want to fix to a wall or other surface,
perform step b after first securing the
stand with screws.
connecting with a single HDMI cable.
It is recommended that you determine the
reception strength before securing the
stand with the screws.
To connect to a TV with no HDMI input, see
Connecting to a TV with no HDMI input on
page 79.
1
2
Connect the AM and FM antennas .
5
Connect an audio cable from your TV to
the receiver.
a. Connect one wire of the AM loop antenna
2
to each AM antenna terminal .
To listen to TV audio on this unit, connect the
TV’s audio output to DIGITAL IN1 (OPTICAL)
For each terminal, press down on the tab to
open; insert the wire, then release to
secure.
4
on the receiver.
Use a coaxial audio cable to connect to a TV
with no optical digital audio input, see Using
this unit for TV audio on page 46.
2
3
1
• To use the HDMI Control function when you
are connected to a supported Pioneer Flat
Screen TV, you must connect via HDMI.
3
You must first set ‘TV Input’ to switch the input
source of this unit to TV audio or to switch the
audio from a Flat Screen TV with the HDMI
Control function. For more information, see
Audio input settings from the TVs (TV Input) on
page 46.
b. Push the FM antenna plug onto the center
pin of the FM antenna socket.
Note
1 • Keep antenna cables away from the receiver and other cables.
• If reception with the supplied antenna is poor, see Improving poor FM reception and Improving poor AM sound on
page 39 or Connecting external antennas on page 49.
• Do not attach any antenna other than the provided loop antenna, or an external antenna as described on page 49.
2 • Don’t let it come into contact with metal objects and avoid placing near computers, television sets or other electrical
appliances.
• If radio reception is poor, you may be able improve it by re-inserting each antenna wire into the opposite terminal.
• For best reception, do not untwist the AM loop antenna wires or wrap them around the loop antenna.
3 To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of
the unit.
4 When digital connections are used, it may be necessary to adjust the digital audio output settings on the TV. For
details, consult the operating instructions for your TV.
27
En
Download from Www.Somanuals.com. All Manuals Search And Download.
03
Connecting up
6
Connect the power cords.1
AC IN
To AC outlet
• Connect each power cord to the AC inlet on
the Blu-ray disc player and the receiver.
Connect each power cord to a wall socket
in the following order:
1. Blu-ray disc player
2. Receiver
3. TV
• SX-LX08 model only: Connect the powered
subwoofer’s power cord in the same way.
Note
1 • Do not use any power cord other than the one supplied with this system.
• Do not use the supplied power cord for any purpose other than connecting to this system.
• After connecting this unit to an AC outlet, a 15-second initialization process begins. You cannot carry out any
operations during initialization. The HDMI indicator on the display unit blinks during initialization, and you can turn
this unit on once it has stopped blinking.
28
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
04
Chapter 4
Getting started
1
Connect the microphone to the MCACC
jack on the front panel.
• Open the front panel door to access the
MCACC jack.
Using the Auto MCACC setup for
optimal surround sound
The Multichannel Acoustic Calibration
(MCACC) system measures the acoustic
characteristics of your listening area, taking
into account ambient noise, and testing for
channel delay and channel level. After you
have set up the microphone provided, the
system uses the information from a series of
test tones to measure reverb, optimizing the
speaker settings and equalization (Acoustic
iPod DIRECT
PHONES
MCACC
DIRECT
MCACC
1
Calibration EQ) for your particular room.
Microphone
Place the microphone at your normal
listening position.
Place it about ear height, and make sure it is
level by using a table or chair.
Important
2
• The test tones used for Auto MCACC setup
are loud; however, do not turn the volume
down during setup as this may result in a
sub-optimal setup.
Make sure there are no obstacles between the
speakers and the microphone.
• Make sure the microphone and speakers
are not moved during the MCACC setup.
RECEIVER
3
If the system isn’t already on,
switch it on.
SX-LX08 model only: If using a subwoofer, be
sure it is switched on and set to a comfortable
listening level.
MCACC
POPUP
MENU
4
Press MCACC.
Try to be as quiet as possible after pressing
MCACC. The volume increases automatically
and the system outputs a series of test tones.
• To cancel Auto MCACC setup before it has
finished, press MCACC. The unit will
continue to use the previous settings.
Note
1 You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).
29
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Getting started
• If the ambient noise level is too high,
Noisy! blinks in the display for five
seconds. To exit and check the noise
1
levels , press MCACC, or to try again, press
ENTER when Retry shows in the display.
• If you see an Error MIC! or Error Speaker!
message in the display, there may be a
problem with the microphone or the
speaker connections. To try again, press
2
ENTER .
• SX-LX08 model only: If the display shows the
‘
Error SW!’ message, the unit was unable
to detect output from the subwoofer.
Check and confirm that the subwoofer's
power switch is turned on, and set the
volume to a comfortable listening level,
then press ENTER once again.
When the MCACC setup is complete, the
volume level returns to normal, Complete
3
shows in the display, and Acoustic Calibration
4
EQ is activated.
• Be sure to disconnect the microphone
from this unit upon completion of the Auto
MCACC setup.
Note
1 • If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles
blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air
conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.
• Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off the TV during
Auto MCACC setup.
2 If this doesn’t work, press MCACC, turn off the power, and check the problem indicated by the Error message, then try the
Auto MCACC setup again.
3 If Complete doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.
4 See Listening with Acoustic Calibration EQ on page 34 to switch on/off Acoustic Calibration EQ.
30
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
05
Chapter 5
Listening to your system
• LX03BD model only: If you set up the system
Important
for Front surround (page 16), the Front
Stage Surround modes will give the best
results (page 33).
• This unit’s audio function may be restricted
depending on the sound source, Line
Output setting (page 48), and HDMI audio
setting (page 51). In this event, the menus
may not appear, or a message may be
displayed instead (page 62).
SURROUND
•
Press repeatedly to select a
listening mode.1
The choices that appear in the display will vary
according to the type of source that’s playing.
With two channel sources, you can select from:
Auto listening mode
• Auto – See Auto listening mode above
The Auto listening mode is the simplest way to
listen to any source as it was mastered: the
output from the speakers mirrors the channels
in the source material.
2
• 2PL II Movie (Dolby Pro Logic II Movie) –
5.1 channel surround sound, especially
suited to movie sources
• LX03BD model only: If you set up the system
for Front surround (page 16), the Front
Stage Surround modes will give the best
results (page 33).
2
• 2PL II Music (Dolby Pro Logic II Music) –
5.1 channel surround sound, especially
suited to music sources; see Dolby Pro
Logic II Music settings below
SURROUND
2
• 2Pro Logic (Dolby Pro Logic) – 4.1
•
Press to select the Auto listening
channel surround sound for use with any
two-channel source
mode.1
• When playing stereo sources, the STEREO
indicator will light. The 2D indicator will
light when playing a Dolby Surround sound
source.
• Stereo – See Listening in stereo on page 33
• A.L.C. – See Listening in stereo on page 33
With multichannel sources, you can select
(according to format):
• Auto – See Auto listening mode above
• Stereo – See Listening in stereo on page 33
• A.L.C. – See Listening in stereo on page 33
Listening in surround sound
You can listen to stereo or multichannel
sources in surround sound. Surround sound is
generated from stereo sources using one of
the Dolby Pro Logic decoding modes.
Note
1 • If the source is Dolby Digital or DTS, the corresponding indicator lights in the front panel display.
• During 88.2 kHz/96 kHz source playback, the listening mode is fixed to Auto and cannot be changed.
2 The 2PL II indicator will light.
31
En
Download from Www.Somanuals.com. All Manuals Search And Download.
05
Listening to your system
Dolby Pro Logic II Music settings
When listening in Dolby Pro Logic II Music
mode (see above), there are three settings you
can adjust: Center Width, Dimension, and
Panorama.
Using Advanced Surround
The Advanced Surround effects can be used
with any multichannel or stereo source for a
variety of additional surround sound effects.
These modes are designed to provide optimum
listening effect when using the Standard
surround setup described on page 16, 23.
SOUND
VIDEO
SELECT
1
Press when Dolby Pro Logic II Music
mode is active.
ADV SURR
•
Press to select an Advanced
Surround mode.
ENTER
The ADV SURR indicator lights when one of
these modes is chosen. You cannot switch
between modes for some audio streams.
2
Select ‘Center Width’,
‘
Dimension’ or ‘Panorama’ then press
1
ENTER
.
• Center Width – Provides a better blend of
the front speakers by spreading the center
channel between the front right and left
speakers, making it sound wider (higher
settings) or narrower (lower settings).
Press repeatedly to select:
• Action – Designed for action movies with
dynamic soundtracks
• Unplugged – Suitable for acoustic music
sources
• Dimension – Adjusts the depth of the
surround sound balance from front to
back, making the sound more distant
(minus settings), or more forward (positive
settings).
• Expanded – Creates an extra wide stereo
field.
• TV Surround – Provides surround sound
for both mono and stereo TV sources.
• Sports – Suitable for sports programs
• Panorama – Extends the front stereo
image to include the surround speakers for
a ‘wraparound’ effect.
• Advanced Game – Suitable for video
games
• Virtual – The virtual surround effect is
heard only from the front speakers, and
from the subwoofer.
ENTER
3
Adjust the setting, then press
ENTER to confirm.
• Ext Stereo – Gives multichannel sound to
a stereo source, using all of your speakers.
Note
1 • During 88.2 kHz/96 kHz source playback, the listening mode is fixed to Auto and cannot be changed.
• When using a Pioneer Flat Screen TV with HDMI Control function support, these operating modes can be changed by
operating the TV.
32
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
Using Front Stage Surround
05
• Stereo – The STEREO indicator will light
and ordinary stereo sound will be
produced.
Advance
• A.L.C. – Listening in Auto level control
stereo mode. The STEREO and ALC
indicators will light.
(LX03BD model only)
The Front Stage Surround Advance modes are
effective when you are using the Front
surround setup as described on page 16.
Listening with headphones
ADV SURR
When headphones are connected, only the
Stereo, A.L.C. and PhonesSurround modes
are available.
•
Press to select a Front Stage
Surround Advance mode.
The F.S.SURR indicator lights. You cannot
switch between modes for some audio
•
With headphones connected, press
1
streams.
SURROUND to select Stereo or A.L.C., or
press ADV SURR to select PhonesSurround
• Stereo – See Listening in stereo above
.
Press repeatedly to select:
• F.S.S.Focus5.1 – Use to provide a rich
surround sound effect directed to the
center area where the left and right
speakers sound projection converges.
• A.L.C. – See Listening in stereo above
• PhonesSurround – Virtual surround
sound for headphones.
• F.S.S.Wide5.1 – Use to provide a surround
sound effect to a wider area than
F.S.S.Focus5.1 mode.
Using the Sound Retriever
When audio data is removed during the MP3 or
WMA compression process, sound quality
often suffers from an uneven sound image. The
Sound Retriever feature employs new DSP
technology that helps bring CD quality sound
back to compressed two channel audio by
restoring sound pressure and smoothing
jagged artifacts left over after compression.
• Extra Power – Outputs stereo sound (in
the case of multichannel sources, down-
mixed stereo sound) from the surround
speakers for powerful stereo effect.
Listening in stereo
You can listen to any source — stereo or
multichannel — in stereo. When playing a
multichannel source, all channels are
downmixed to the front left/right speakers and
the subwoofer.
SOUND
RETRIEVER
•
Press while listening to a stereo
source.1
Press repeatedly to switch between:
In the Auto level control stereo mode (A.L.C.),
this unit equalizes playback sound levels if
each sound level varies with the music source
recorded in a portable audio player.
• Retriever On — Switches the Sound
Retriever on. The S.RTRV indicator lights.
• Retriever Off — Switches the Sound
Retriever off.
SURROUND
•
Press repeatedly to select Stereo or
A.L.C. mode.
Note
1 This setting cannot be used with multichannel or 88.2 kHz/96 kHz sources.
33
En
Download from Www.Somanuals.com. All Manuals Search And Download.
05
Listening to your system
ENTER
Listening with Acoustic
Calibration EQ
3
Select the amount of Dialogue
Enhancement then press ENTER to confirm.
Select between Off, Mid, Max or Auto.
You can listen to sources using the Acoustic
Calibration Equalization set in Using the Auto
MCACC setup for optimal surround sound on
• When Dialogue is set to Auto, the amount
of Enhancement is selected automatically
to optimally match the audio signal.
1
page 29.
SOUND
• The DIALOG indicator lights when
Dialogue Enhancement is active.
VIDEO
SELECT
1
Press to open the sound menu.
Select ‘MCACC EQ’ then press
Using Midnight and Quiet
listening modes
ENTER
2
ENTER
.
The Midnight listening feature allows you to
hear effective surround sound of movies at low
volume levels.
ENTER
3
Switch ‘EQ On’ or ‘EQ Off’ then
The Quiet listening feature reduces excessive
bass or treble in a sound source.
press ENTER to confirm.
• The MCACC indicator lights when Acoustic
Calibration EQ is active.
SOUND
• On the EQ Off setting, equalization is set to
off and speaker settings (channel delay
and channel level) remains as it is set.
VIDEO
SELECT
1
2
3
Press to open the sound menu.
Select ‘Tone’ then press ENTER
ENTER
• EQ On is selected automatically after the
Auto MCACC setup is completed.
.
ENTER
Enhancing dialogue
S
elect ‘Midnight’ or ‘Quiet’ then
press ENTER to confirm.
• The TONE indicator lights.
The Dialogue Enhancement feature is
designed to make the dialogue stand out from
other background sounds in a TV or movie
soundtrack.
• To cancel the Midnight or Quiet listening
modes, select Bass/Treble.
SOUND
VIDEO
SELECT
1
Press to open the sound menu.
Select ‘Dialogue’ then press
ENTER
2
ENTER
.
Note
1 Acoustic Calibration EQ is not available when headphones are connected.
34
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to your system
05
ENTER
Adjusting the bass and treble
3
Select the desired Bass Mode
Use the bass and treble controls to adjust the
overall tone.
setting, then press ENTER to confirm.
Select between Off, Music, Cinema or Auto.
SOUND
• When Bass Mode is set to Auto, the
setting (Music or Cinema) is selected
automatically to optimally match the audio
signal.
VIDEO
SELECT
1
Press to open the sound menu.
Select ‘Tone’ then press ENTER
ENTER
• The BASS MODE indicator lights when
Bass Mode is active.
2
3
.
ENTER
S
elect ‘Bass/Treble’ then press
Adjusting sound delay
ENTER
.
Some monitors have a slight delay when
showing video, so the soundtrack will be
slightly out of sync with the picture. By adding
a bit of delay, you can adjust the sound to
match the presentation of the video.
• Selecting Bass/Treble cancels the
Midnight and Quiet listening modes. These
modes cannot be used at the same time.
ENTER
There are a total of 60 steps (levels) that you
can adjust, with a total range of 200 msec.
4
Use / to select ‘Bass’ or
‘Treble’; use / to adjust the sound then
SOUND
press ENTER to confirm.
• Bass and Treble can be adjusted from –6dB
VIDEO
SELECT
1
Press to open the sound menu.
Select ‘Sound Delay’ then press
to +6dB
.
• When the Bass or Treble is set to
something other than 0dB, the TONE
indicator lights.
ENTER
2
ENTER
.
Boosting the bass level
ENTER
There are two bass modes you can use to
3
Select the length of the delay in
1
enhance the bass in a source.
sound, then press ENTER to confirm.
• This option is deactivated and not
displayed if you have Auto Delay set to On
in HDMI Setup (see Setting the Auto Delay
on page 51).
SOUND
VIDEO
SELECT
1
Press to open the sound menu.
Select ‘Bass Mode’ then press
ENTER
2
ENTER
.
Note
1 The Bass Mode is not available when headphones are connected.
35
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Connecting an iPod
Chapter 6
Connecting an iPod
1
Set this unit to the standby mode, and
then use the USB cable (for iPod connection)2
to connect your iPod to the iPod DIRECT
terminal on the front panel of this unit.
For the cable connection, refer to also the
operating instructions for iPod.
Connecting your iPod to this
unit
This unit has a dedicated iPod terminal that
will allow you to control playback of audio
content from your iPod using the controls of
1
2
Switch the unit on and press the iPod
this unit.
input source button on the remote control to
switch the unit to the iPod.
iPod DIRECT
PHONES
MCACC
The front panel display shows Loading while
the unit verifies the connection and retrieves
data from the iPod.
TOP MENU
3
Press to display iPod Top menu.
iPod DIRECT
When the display shows Top Menu you’re
3
ready to play music from the iPod.
• If after pressing iPod the display shows
No Device, try switching off the unit and
reconnecting the iPod to the unit.
USB cable (for
iPod connection)
iPod playback
iPod
MENU
This unit’s front panel display can be used to
4
navigate tracks on your iPod.
Note
1 • This unit is compatible with the audio of iPod nano, iPod fifth generation, iPod classic, iPod touch (not supported iPod shuffle
and iPhone). However, that some of the functions may be restricted for some models. Note, however, compatibility may vary
depending on the software version of your iPod. Please be sure to use the latest available software version.
• iPod is licensed for reproduction of non-copyrighted materials or materials the user is legally permitted to reproduce.
• Features such as the equalizer cannot be controlled using this unit, and we recommend switching the equalizer off before
connecting.
• Pioneer cannot under any circumstances accept responsibility for any direct or indirect loss arising from any inconvenience
or loss of recorded material resulting from the iPod failure.
2 The USB cable (for iPod connection) is not included with this unit.
3 The controls of your iPod will be inoperable when connected to this unit. Features such as the equalizer cannot be controlled
using this unit, and we recommend switching the equalizer off before connecting.
4 • Note that non-roman characters in the title are displayed as #.
• This feature is not available for photos or video clips on your iPod.
36
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an iPod
06
Finding what you want to play
Basic playback controls
When your iPod is connected to this unit, you
can browse songs stored on your iPod by
playlist, artist, album name, song name, genre
or composer, similar to using your iPod directly.
The following table shows the basic playback
controls for your iPod. Press iPod to switch the
remote control to the iPod operation mode.
Button
What it does
Press to start playback.
ENTER
If you start playback when something
other than a song is selected, all the
songs that fall into that category will
play.
1
Select a category, then press
ENTER to browse that category.
• To return to the previous level any time,
press RETURN.
Pauses playback, or restarts playback
when paused.
ENTER
Press and hold during playback to start
scanning.
/
/
2
Browse the selected category
(e.g., albums).
Press to skip to previous/next track.
• Use / to move to previous/next levels.
3
Continue browsing until you arrive at
Press repeatedly to switch between
Repeat One, Repeat All and Repeat
Off.
what you want to play, then press
to start
SUBTITLE
playback.1
Navigation through categories on your iPod
looks like this:
Playlists Songs
Artists Albums Songs
Albums Songs
Press repeatedly to switch between
Shuffle Songs, Shuffle Albums and
Shuffle Off.
ANGLE
Press repeatedly to change the song
playback information displayed in the
front panel display.
DISPLAY
Songs
Podcasts
Genres Artists Albums Songs
Composers Albums Songs
Audiobooks
When browsing, press to move to
previous/next levels. During playback,
press to skip to previous/next track.
Shuffle Songs
During Audiobook playback, press to
switch the playback speed: Faster
Normal Slower
Tip
Press to return to the iPod Top menu
screen.
TOP MENU
RETURN
• You can play all of the songs in a particular
category by selecting the All item at the top
of each category list. For example, you can
play all the songs by a particular artist.
Press to return to the previous level.
Note
1 If you’re in the song category, you can also press ENTER to start playback.
37
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Connecting an iPod
1
Switching the iPod controls
Important
You can switch over the iPod controls between
If an error message lights in the front panel
display, try following the points below:
the iPod and the unit.
CTRL
1
Press to switch the iPod controls.2
Symptom What it means
ThisAwUDiIlOl enable the controls and display on
your iPod; simultaneously, this unit’s remote
control unit will be disabled.
Error I1 There is a problem with the signal path
from the iPod to the unit. Switch off the
unit and reconnect the iPod to the unit.
If this doesn’t seem to work, try resetting
your iPod.
CTRL
AUDIO
2
Press again to switch back to the
receiver controls.
Error I2 The software version being used with
the iPod needs to be updated. Update
the software being used with the iPod
(please use the latest iPod software
versions later than the iPod updater
2004-10-20).
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
Error I3 The iPod that is not supported is
connected. Check whether the iPod was
supported by this unit (page 36).
When the iPod software version is too
old, update the iPod software to the
latest version.
Error I4 When there is no response from the
iPod, update the iPod software to the
latest version. If this doesn’t seem to
work, try resetting your iPod.
iPod Error The power requirements of the iPod are
too high for this unit.
NoMusic There are no playable songs currently
Track
stored in the iPod. Input some music
files compatible with iPod playback.
No Track When there are no tracks in the
category selected on the iPod. Select a
different category.
Note
1 You cannot use this function, when an iPod of fifth generation or iPod nano of first generation is connected.
2 When this function is set, iPod images cannot be played on this unit.
38
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the radio
07
Chapter 7
Listening to the radio
Improving poor FM reception
Listening to the radio
If you’re listening to an FM station in stereo but
the reception is weak, you can improve the
sound quality by switching to mono.
The tuner can receive both FM and AM
broadcasts, and lets you memorize your
favorite stations so you don’t have to manually
tune in every time you want to listen.
SETUP
1
Press after tuning to an FM radio
Select ‘Tuner Setup’ then press
Choose ‘FM Auto/Mono’ then
TOOLS
FM/AM
station.
TUNER
1
Switch to the tuner, then press
repeatedly to select the FM or AM band.
The display shows the band and frequency.
ENTER
2
TUNE
ENTER
.
2
Tune to a frequency.
TUNE
ENTER
There are three tuning modes — manual, auto,
and high-speed:
3
press ENTER
.
• Manual tuning – Press TUNE +/–
repeatedly to change the displayed
frequency.
ENTER
4
Select ‘FM Mono’ then press
• Auto tuning – Press and hold TUNE +/–
until the frequency display starts to move,
then release. The tuner will stop on the next
station it finds. Repeat to keep searching.
ENTER
.
The mono indicator ( ) lights when the tuner
is in mono reception mode.
Select FM Auto above to switch back to auto-
• High-speed tuning – Press and hold
TUNE +/– until the frequency display starts
to move rapidly. Keep the button held down
until you reach the frequency you want. If
necessary, fine tune the frequency using
the manual tuning method.
stereo mode (the stereo indicator (
when receiving a stereo broadcast).
) lights
Improving poor AM sound
The simplest way to improve the sound quality
of AM radio is to make sure that the TV in the
room is switched off. Also try changing the
position and direction of the AM loop antenna.
39
En
Download from Www.Somanuals.com. All Manuals Search And Download.
07
Listening to the radio
Changing the noise cut mode
Memorizing stations
If you find that the AM sound quality is bad
even after trying the above, you may be able to
improve it using a different noise cut mode.
Just choose the one that sounds best.
This system can memorize up to 30 stations,
stored in three banks, or classes (A, B and C) of
10 stations each.
1
Tune to an FM or AM radio station.
Select mono or auto-stereo reception (FM) or
the Noise Cut mode (AM) as necessary. These
settings are saved along with the preset.
SETUP
1
Press after tuning to an AM radio
Select ‘Tuner Setup’ then press
Choose ‘Noise Cut’ then press
TOOLS
station.
T.EDIT
OUTPUT
2
Press T.EDIT.
RESOLUTION
CLASS
ENTER
2
ENTER
.
HOME MEDIA
GALLERY
3
Press to select one of the three
classes, then press ST +/– to select the station
preset you want.
You can also use the number buttons to select
a preset.
ENTER
3
ENTER
.
ENTER
ENTER
4
Press ENTER.
4
Select a Noise cut mode (1, 2 or 3)
After pressing ENTER, the preset class and
number stop blinking and the system
memorize station.
then press ENTER
.
Listening to station presets
You will need to have some presets stored to do
this.
CLASS
HOME MEDIA
1
Press to select the class in which
GALLERY
the channel is stored.
Press repeatedly to cycle through classes A, B
and C.
ST
ST
2
Select the station preset you
want.
• You can also use the number buttons on
the remote control to recall the station
preset.
40
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening to the radio
Using RDS
07
Displaying RDS information
Use DISPLAY to display the different types of
2
Radio Data System (RDS) is a system used by
most FM radio stations to provide listeners with
various kinds of information — the name of the
station and the kind of show they’re
RDS information available.
DISPLAY
•
Press for RDS information.
Each press changes the display as follows:
broadcasting, for example.
• Radio Text (RT) – Messages sent by the
radio station. For example, a talk radio
station may provide a phone number as RT.
One feature of RDS is that you can search by
type of program. For example, you can search
for a station that’s broadcasting a show with
the program type, Jazz.
• Program Service Name (PS) – The name of
the radio station.
1
You can search the following program types:
• Program Type (PTY) – This indicates the
kind of program currently being broadcast.
News – News
Finance – Stock market
Affairs – Current Affairs
reports, commerce,
Info – General Information trading, etc.
• PTY SEARCH – PTY search (see below)
Sport – Sport
Children – Programs for
children
• Current tuner frequency
Educate – Educational
Drama – Radio plays, etc. Social – Social affairs
Culture – National or
regional culture, theater,
etc.
Science – Science and
technology
Varied – Usually talk-
based material, such as
quiz shows or interviews.
Pop M – Pop music
Rock M – Rock music
Easy M – Easy listening
Religion – Programs
concerning religion
Phone In – Public
expressing their views by
phone
Travel – Holiday-type travel
information as opposed to
traffic announcements.
Leisure – Leisure interests
and hobbies
Searching for RDS programs
You can search for a program type listed above.
FM/AM
TUNER
1
Press for the FM band.3
DISPLAY
2
Press repeatedly until ‘PTY
SEARCH’ appears in the display.
Jazz – Jazz
Light M – ‘Light’ classical Country – Country music
music
Classics – ‘Serious’
classical music
Nation M – Popular music
in a language other than
English
3
Select the program type you want
to hear.
Other M – Music not fitting Oldies – Popular music
above categories
from the ’50s and ’60s
Folk M – Folk music
Document – Documentary
ENTER
4
Start the search.
Weather – Weather
reports and forecasts,
meteorological information
The system searches the station presets for a
match. If it finds one, searching stops for five sec.
5
If you want to keep listening to the
station, press ENTER within the five seconds.
If you don’t press ENTER, searching resumes.
Note
1 In addition, there are three other program types, TEST, ALARM!, and None, ALARM! and TEST are used for emergency
announcements. None appears when a program type cannot be found.
2 • If any noise is picked up while displaying the RT scroll, some characters may be displayed incorrectly.
• If you see No Radio Text Data in the RT display, it means no RT data is sent from the broadcast station. The display will
automatically switch to the PS data display (if no PS data, the frequency is displayed).
• In the PTY display, NO DATA or None may be shown. In this case, the PS display is shown after a few seconds.
3 RDS is only possible in the FM band.
41
En
Download from Www.Somanuals.com. All Manuals Search And Download.
08
Surround sound settings
CShuaprterr o8 und sound settings
• Dynamic Range Compression
Important
Resuscitates detailed sound susceptible to
ambient noise to create an acoustic
environment where you feel as if you are
right in the action.
• This unit’s audio function may be restricted
depending on the Line Output setting
(page 48) and HDMI audio setting
(page 51). In this event, the menus may not
appear.
• Frequency Characteristic Correction
(LX03BD model only)
Realizes the playback characteristic
optimized for long hours of listening in
addition to the added features of the
supplied speaker units.
Using the Sound Setup menu
From the Sound Setup menu you can access
all the surround sound settings of the system.
The Effective Sound mode can be turned off
(activating Direct Sound mode) by doing the
following:
During setup, the speakers are represented by
the following letters:
• L – Front left speaker
• C – Center speaker
SETUP
1
Press SETUP.
TOOLS
• R – Front right speaker
• SR – Surround right speaker
• SL – Surround left speaker
• SW – Subwoofer
ENTER
2
Select ‘Sound Setup’, then press
ENTER
.
Effective Sound (for optimum
ENTER
sound)
3
Select ‘Sound Field’, then press
Select ‘Direct Sound’, then press
With the uniquely shaped high-quality
speakers supplied with this unit, the Effective
Sound mode enables the following Pioneer
exclusive audio technologies designed to
maximize the real experience of sound
originally inherent in movies and music.
ENTER
.
ENTER
4
ENTER to confirm.
To return to Effective Sound mode, perform the
same procedure noted above to select
‘EffectiveSound’.
Turn on the Effective Sound mode under
normal circumstances to maximize the
1
capabilities of this unit.
• When Direct Sound is selected, the
DIRECT indicator lights.
Note
1 The Sound Field setting is not available when headphones are connected.
42
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround sound settings
08
1
Speaker distance setting
Channel level setting
The Auto MCACC feature (see page 29) should
give you the best surround sound setup.
However you may find that by further
adjustment of the speaker distance settings
you can improve the surround sound in your
listening room.
The Auto MCACC feature (see page 29) should
give you the best surround sound setup.
However you may find that by further
adjustment of the channel levels you can
improve the surround sound in your listening
room.
Set the distance of each speaker from your
normal listening position.
This method of setting the channel levels
allows you to listen to a source and adjust the
levels of each playback channel.
SETUP
ENTER
The test tone method can also be used to
adjust channel levels.
1
Open the ‘Sound Setup’
TOOLS
2
menu.
SETUP
ENTER
ENTER
1
Open the ‘Sound Setup’
TOOLS
2
Select ‘Distance’, then press
menu.
ENTER
.
ENTER
2
Select ‘ChannelLevel’, then press
3
Use / to select a speaker or
ENTER
.
/ to adjust the distance.
Each speaker can be adjusted from 0.1m to
9.0m.
3
Use / to select a channel3 or
/ to adjust the level of that channel.
• You can adjust the level of each channel by
10 dB.
ENTER
4
Press ENTER when you’re finished.
• If you use the Auto MCACC feature again,
it will overwrite the settings you have made
here.
ENTER
4
Press once when you’re finished.
• If you use the Auto MCACC feature again,
it will overwrite the settings you have made
here.
Note
1 The Channel level setting is not available when headphones are connected.
2 No test tone is output when audio is muted.
3 When Test Tone is selected, the test tone moves automatically from speaker to speaker in the order
LCRSRSLSW. Adjust the / controls so that the test tone is heard at the same volume from each speaker when
sitting in the main listening position. However, the test tone from the subwoofer may sound lower than other tones, in which
case adjust the level while listening to a source. Press ENTER when you’re finished.
43
En
Download from Www.Somanuals.com. All Manuals Search And Download.
08
Surround sound settings
Dynamic Range Control
Dual mono setting
When watching Dolby Digital or DTS material
at low volume, low level sounds — including
some of the dialog — can be difficult to hear
properly. Using one of the Dynamic Range
Control (DRC) settings can help by bringing up
the low level sounds, while controlling high
level peaks.
Specifies how dual mono encoded Dolby
Digital soundtracks should be played. This
setting can also be used to change the audio
channels for DVD-RW discs recorded in
bilingual audio, and external inputs with
bilingual audio (HDMI and optical/coaxial
digital inputs).
Dynamic Range Control works only with Dolby
Digital soundtracks and some DTS
soundtracks.
SETUP
ENTER
1
Open the ‘Sound Setup’
TOOLS
menu.
SETUP
ENTER
1
Open the ‘Sound Setup’
TOOLS
ENTER
menu.
2
Select ‘Dual Mono’, then press
Select a setting.
ENTER
.
ENTER
2
Select ‘D.R.C.’, then press ENTER
.
3
Select one of the following:
3
Select a setting.
• CH1 Mono – Only channel 1 is played
• CH2 Mono – Only channel 2 is played
Select one of the following:
• D.R.C. High – Dynamic range is reduced
(loud sounds are reduced in volume while
quieter sounds are increased)
• CH1/CH2 – Both channels are played
through the front speakers
• D.R.C. Mid – Mid setting
Virtual Surround Back
This mode allows you to use your surround
speakers with standard surround setup to
listen to a virtual surround back channel. You
can choose to listen to sources with no
surround back channel information, or if the
material sounds better in the format (for
example, 5.1) for which it was originally
encoded, you can have the unit only apply this
effect to 6.1 encoded sources like Dolby Digital
• D.R.C. Off – No dynamic range adjustment
(use when listening at higher volume)
ENTER
4
Press to exit.
1
EX or DTS-ES.
SETUP
ENTER
1
Open the ‘Sound Setup’
TOOLS
menu.
Note
1 • Depending on the input signal and the listening mode, the Virtual Surround Back mode may not be effective.
• The Virtual Surround Back mode is not effective when the headphones are connected or when using the Front surround setup.
44
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Surround sound settings
08
DTS CD setting
ENTER
If you play a DTS-encoded CD, you will need to
change this setting to hear the decoded signal.
2
Select ‘Virtual SB’, then press
ENTER
.
SETUP
ENTER
1
Open the ‘Sound Setup’
TOOLS
3
Select a setting.
menu.
Select one of the following:
• Vir.SB On – Virtual Surround Back is
always used (for example, on 5.1 encoded
material).
ENTER
2
Select ‘CD Type’, then press ENTER.
Select a setting.
• Vir.SB Off – Virtual Surround Back mode
is switched off.
3
The V.SB indicator lights when Virtual
Surround Back is active.
Select one of the following:
• Normal CD – Use for playback of regular
audio CDs. Some DTS-encoded CDs will
output noise when played.
ENTER
4
Press to exit.
• DTS-CD – Use for playback of DTS-
encoded CDs, but note that the beginning
of regular CD tracks may be skipped.
LFE Attenuate
Some Dolby Digital and DTS audio sources
include ultra-low bass tones.
ENTER
Set the LFE attenuator as necessary to prevent
the ultra-low bass tones from distorting the
sound from the speakers.
4
Press to exit.
SETUP
ENTER
1
Open the ‘Sound Setup’ menu.
TOOLS
ENTER
2
3
Select ‘LFE ATT’, then press ENTER.
Select a setting.
Select one of the following:
• 0dB – The LFE is not limited, which is the
recommended value.
• -10dB – The LFE is limited by the respective
degree.
• LFE Off – No sound is output from the LFE
channel.
ENTER
4
Press to exit.
45
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Other connections
Chapter 9
Other connections
• When digital connections are used, it may
Important
be necessary to adjust the digital audio
output settings on the TV. For details,
consult the operating instructions for your
TV.
• When making or changing connections on
the rear panel of this unit, be sure to switch
power off and disconnect the power cord
from the wall socket.
After completing all connections, connect
the power cord to the wall socket.
Audio input settings from the TVs
(TV Input)
To listen to audio from a Flat Screen TV on this
device, you will need to connect an audio cable
other than an HDMI cable. From this menu, set
the audio input to that which you would like to
connect. Press TV on the remote control to
switch this unit to the input source selected
here. This setting is changed to the selected
input and the audio from the Flat Screen TV is
output from this device.
Using this unit for TV audio
To listen to audio from a TV, connect the TV’s
audio cable to one of the inputs on this unit.
TV
Select from inputs Digital 1 OPT, Digital 2
From analog output
OPT, Digital 3 COAX and Analog.
From digital output
SETUP
(coaxial)
(optical)
1
2
Press SETUP.
TOOLS
ENTER
Select ‘System Setup’ then press
Select ‘TV Input’, then press
Adjust the setting then press
ANALOG
L
OPTICAL
ENTER
.
1
2
AM
R
LOOP
AUDIO IN
FM
UNBAL
75
ANTENNA
DIGITAL IN
ENTER
COAX
3
OUT
IN
2
IN
1
DIGITAL IN
HDMI
3
ENTER
.
•
Connect the audio output jacks on your
TV to the audio input jacks on the receiver.
• You can connect by either a digital or
analog audio cable. Select only one
method to make connections.
ENTER
4
ENTER to confirm.
• To use the HDMI Control function when
you are connected to a supported Pioneer
Flat Screen TV, you must connect via
HDMI.
46
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
09
• When digital connections are used, it may
be necessary to adjust the digital audio
output settings on the connected
component. For details, consult the
operating instructions for the component
involved.
Listening to the sound of an
external device on this receiver
You can connect both analog and digital
external audio sources to this system.
• For a device with a video output, connect
directly to the TV using a separate video
cable, etc.
Connecting an analog audio
component
You can use the ANALOG AUDIO IN jacks to
connect an analog audio component, such as
a VCR or tape player.
We recommend using an HDMI cable to
connect sources that have HDMI terminals.
For more information see Connecting using
HDMI on page 50.
To video input
Connecting for digital audio
This system has several digital inputs for digital
playback components, such as your HDD/DVD
recorder, digital satellite receiver or TV game.
TV
VCR, Tape player, etc.
To video input
From
analog output
TV
ANALOG
L
HDD/DVD recorder, STB, etc.
R
AUDIO IN
From digital
From digital
or
output (optical)
output (coaxial)
COAX
DIGITAL IN
3
OUT
IN
2
IN
1
HDMI
Listening to an external audio source
To listen to audio from a connected external
component on this system, choose its input
function on the remote control. Some Pioneer
products can be controlled via this remote.
ANALOG
L
OPTICAL
1
AM
R
LOOP
AUDIO IN
FM
2
UNBAL
75
ANTENNA
DIGITAL IN
COAX
3
OUT
IN
2
IN
1
DIGITAL IN
HDMI
RECEIVER
•
Connect the digital output jack on HDD/
1
If the system isn’t already on, switch
DVD recorder, etc. to one of the DIGITAL
input jacks on this unit.
Use a commercially available optical cable or
coaxial cable to make this connection.
it on.
Also make sure that the external source (TV,
HDD/DVD recorder, etc.) is switched on.
47
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Other connections
Line Output setting
LINE
2
Select an audio input source.
Use to select the audio down-mix method
when outputting Dolby Digital multi-channel
sound sources from the ANALOG AUDIO
Input sources are cycled through as shown
below:
1
Digital 1 OPT
OUT jacks.
Analog
SETUP
Digital 2 OPT
Digital 3 COAX
1
2
TOOLS
Press SETUP.
3
If necessary, start playback of the
external source.
ENTER
Select ‘Sound Setup’, then press
Select ‘Line Output’, then press
Select a setting.
ENTER
.
Outputting the sound of this
receiver to an external device
ENTER
You can use the ANALOG AUDIO OUT jacks
to connect an analog audio component, such
as a tape player, and record the sound of the
receiver’s tuner, etc.
3
ENTER.
4
Select one of the following:
Tape player, etc.
• Lo/Ro(Stereo) – A simple stereo downmix
(left-only/right-only, or Lo/Ro) is output
(suitable for playback on a two-channel
stereo system or on headphones).
To
analog input
• Lt/Rt – A surround-compatible downmix
(left-total/right-total, or Lt/Rt) of Dolby
multichannel sources is output, (suitable
for Dolby Surround Pro Logic or other
matrix decoding).
IN
OUT
CONTROL
FRONT
4
CENTER
4
R
R
L
ANALOG
L
AC IN
R
SURROUND
8
SUBWOOFER
4
L
AUDIO OUT
SPEAKERS
The L.OUT indicator lights.
(LX03BD)
ENTER
5
Press to exit.
Note
1 • When the Line Output is switched to Lt/Rt, the sound function will be fixed at the current setting and cannot be changed.
The display will briefly flash Line Out Mode if an attempt is made to use a prohibited function.
• When the Line Output is to Lo/Ro(Stereo), the audio from the analog output jacks may be interrupted, depending on the
operation.
• When using DTS multi-channel sound sources, output is in Lo/Ro(Stereo).
48
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
09
Connecting external antennas
About control out connections
For an external AM antenna, use 5 to 6 meters
of vinyl-insulated wire and set up either indoors
or outdoors. Leave the loop antenna
connected.
Many Pioneer components support CONTROL
connections, by which you can use the remote
controls of any connected components by
aiming them at the sensor of just one
component.
For an external FM antenna, use a PAL
connector to hook up an external FM antenna.
When you use a remote control, the control
signal is passed along the chain to the
appropriate component.
External AM antenna
Outdoor antenna
If you choose to use this feature, you must
make sure that you also have at least one set of
HDMI or analog audio jacks connected to
another component for grounding purposes.
Indoor antenna
(vinyl-coated Wire)
(5 m to 6 m)
External
FM antenna
•
Using a cable with a mono mini-plug on
either end, connect the CONTROL IN jack on
another Pioneer component to the CONTROL
OUT jack on the rear panel.
AM Loop antenna
This will allow you to control the other
component by pointing its remote at the front
panel.
OPTICAL
1
2
AM
LOOP
FM
UNBAL
75
ANTENNA
DIGITAL IN
PAL connector
49
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Other connections
1
Use the supplied HDMI cable to connect
the HDMI IN 1/2 interconnect on this system
to an HDMI output on your HDMI component.
• With the arrow on the cable plug facing up,
connect the plug to the player’s connector.
Connecting using HDMI
If you have a HDMI or DVI (with HDCP)
equipped monitor or display, you can connect
it to this system using the supplied (or
commercially available) for high quality digital
1
video.
See About HDMI on page 52 for more about the
HDMI connection.
Once this system is properly connected to your
HDMI component, the HDMI indicator (red)
lights up on the front panel when you watch
HDMI contents.
TV
2
Use the supplied HDMI cable to connect
To HDMI input
the HDMI OUT interconnect on this system to
an HDMI interconnect on an HDMI-
compatible display.
1/2
ANALOG
1
L
HDMI
3
Press repeatedly to select the HDMI
OPTICAL
input you’ve connected to (for example,
HDMI 2).
1
2
AM
R
LOOP
AUDIO IN
FM
UNBAL
75
You can also use the front panel INPUT to carry
out this operation.
ANTENNA
DIGITAL IN
COAX
3
OUT
IN
2
IN
1
DIGITAL IN
HDMI
• Set the HDMI Audio setting to TV in
Switching the HDMI audio setting below if
you want to hear HDMI audio output from
your TV or Flat Screen TV (no sound will be
heard from this unit).
• If the video signal does not appear on your
TV or Flat Screen TV, try adjusting the
resolution settings on your component or
display.
From HDMI output
HDMI/DVI-equipped component
Note
1 • An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High Bandwidth
Digital Content Protection (HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVIHDMI)
to do so. A DVI connection, however, does not support audio signals. Consult your local audio dealer for more information.
• This system has been designed to be compliant with HDMI (High-Definition Multimedia Interface).
• When HDMI Audio is set to TV, sound is output from this unit to the TV connected to the HDMI connectors in for audio format
supported by that TV.
• Depending on the component you have connected, using a DVI connection may result in unreliable signal transfers.
50
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Other connections
09
Switching the HDMI audio setting
Specifies the routing of the HDMI audio signal
out of this system (amp) or through to a TV or
Flat Screen TV. You cannot use a number of
sound functions of this system when HDMI
audio is set to TV.
Setting the Auto Delay
This feature automatically corrects the audio-
to-video delay between components connected
with an HDMI cable. The audio delay time is set
depending on the operational status of the
display connected with an HDMI cable. The
audio delay time is automatically adjusted
according to the video delay time.
SETUP
1
Press SETUP.
TOOLS
SETUP
1
Press SETUP.
TOOLS
ENTER
2
Select ‘HDMI Setup’ then press
Select ‘HDMI Audio’, then press
Adjust the setting then press
ENTER
.
ENTER
2
Select ‘HDMI Setup’ then press
Select ‘Auto Delay’, then press
Select ‘A.Delay On’ or ‘A.Delay
ENTER
.
ENTER
3
ENTER
.
ENTER
3
ENTER
.
ENTER
4
ENTER to confirm.
ENTER
• AMP – Output an HDMI audio signal from
this system.
4
Off’ then press ENTER to confirm.
• TV – Output an HDMI audio signal from a
1
TV or Flat Screen TV.
Tip
• This feature is only available when the
connected display supports the automatic
audio/video synchronizing capability (‘lip-
sync’) for HDMI or HDMI Control. If you
find the automatically set delay time
unsuitable, set A.Delay to Off and adjust
the sound delay settings manually
(page 35).
Note
1 This makes it possible to use the TV’s built-in speakers to listen to the audio input from an HDMI 1/2 component. In this event,
no sound will be heard from this unit’s speakers (or headphones). All other audio sources (including TUNER) are output from
this unit normally.
51
En
Download from Www.Somanuals.com. All Manuals Search And Download.
09
Other connections
Resetting the HDMI connection
If the screen goes blank (for example, after
changing the resolution), check the
troubleshooting guide on (page 62). If this
doesn’t solve the problem, follow the steps
below to reset the HDMI connection.
SETUP
1
2
3
Press SETUP.
TOOLS
ENTER
Select ‘Initialize’ then press ENTER.
Select ‘HDMI Init’ then press
ENTER
ENTER
.
• Initialize OK? is displayed.
ENTER
4
Press ENTER to confirm initialization.
The system will restart and the HDMI settings
are automatically reset to the factory defaults.
About HDMI
HDMI (High-Definition Multimedia Interface)
supports both video and audio on a single
digital connection for use with DVD players,
DTV, set-top boxes, and other AV devices. HDMI
was developed to provide the technologies of
High-bandwidth Digital Content Protection
(HDCP) as well as Digital Visual Interface (DVI)
in one specification. HDCP is used to protect
digital content transmitted and received by DVI-
compliant displays.
HDMI has the capability to support standard,
enhanced, or high-definition video plus stan-
dard to multichannel surround-sound audio.
HDMI features include uncompressed digital
video, a bandwidth of up to 2.2 gigabytes per
second (with HDTV signals), one connector
(instead of several cables and connectors), and
communication between the AV source and
AV devices such as DTVs.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
52
En
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI Control
10
Chapter 10
HDMI Control
• HDMI Control may not operate properly if
you do not use a High Speed HDMI cable.
Important
• The KURO LINK function name used on
the web and in catalogues is referred to as
HDMI Control in the operating instructions
and on the product.
• Requires connection of audio cables and
additional settings. For details see Audio
input settings from the TVs (TV Input) on
page 46
By connecting this unit to an HDMI Control-
compatible Pioneer Flat Screen TV or the Blu-
ray disc player with an HDMI cable, you can
control this unit from the remote control of a
connected Flat Screen TV, as well as have the
connected Flat Screen TV automatically
change inputs in response to operations
carried out on this unit.
HDMI Control-compatible
Pioneer Flat Screen TV
From optical
digital output
To
HDMI input
Refer to the operating instructions for your Flat
Screen TV for more information about which
operations can be carried out by connecting
via HDMI cable.
• You cannot use this function with
components that do not support HDMI
Control.
ANALOG
L
OPTICAL
1
AM
LO
R
AUDIO IN
FM
UM
75
• We cannot guarantee this unit will work
with HDMI Control-compatible components
other than those made by Pioneer.
2
DIGITAL IN
COAX
3
OUT
IN 2
IN 1
DIGITAL IN
HDMI
Receiver
Making the HDMI Control
connections
You can use synchronized operation for a
connected Flat Screen TV and up to two other
components (including a recorder or player).
FRONT
SURROUND SURROUND BACK CENTER
L
VIDEO OUT
Y
R
VIDEO
SUB WOOFER
AUDIO OUT
(
7.1 ch
)
PB
Be sure to connect the Flat Screen TV’s audio
cable to the audio input of this unit.
HDMI OUT
PR
OPTICAL
CONTROL DIGITAL
IN OUT
COMPONENT
S-VIDEO
VIDEO
Blu-ray disc player
53
En
Download from Www.Somanuals.com. All Manuals Search And Download.
10
HDMI Control
• Connect the Flat Screen TV directly to this
unit. Interrupting a direct connection with
other amps or an AV converter (such as an
HDMI switch) can cause operational
errors.
• Only connect components you intend to use
as a source to the HDMI input of this unit.
Interrupting a direct connection with other
amps or an AV converter (such as an HDMI
switch) can cause operational errors.
HDMI Control-compatible
Pioneer Flat Screen TV
HDMI Control-compatible
Pioneer Flat Screen TV
HDMI input
HDMI cable
HDMI input
HDMI cable
HDMI output
HDMI OUT
P
U
L
L
O
P
E
N
STANDBY
/
ON
HDMI
HDMI input
Other amps
HDMI IN
This unit
or AV converter
HDMI cable
HDMI cable
HDMI OUT
P
U
L
L
O
P
E
N
HDMI output
STANDBY
/
ON
HDMI
This unit
Other amps
or AV converter
Important
• When connecting this system or changing
connections, be sure to switch the power
off and disconnect the power cord from the
wall socket.
After completing all connections, connect
the power cords to the wall socket.
•
After connecting this unit to an AC outlet, a
15-second initialization process begins.
You cannot carry out any operations during
initialization. The HDMI indicator on the
front panel blinks during initialization, and
you can turn this unit on once it has
stopped blinking.
• To get the most out of this function, we
recommend that you connect your HDMI
component not to a Flat Screen TV but
rather directly to the HDMI terminal on this
unit.
54
En
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI Control
10
Setting the HDMI options
Before using synchronization
You must adjust the settings of this unit as well
as HDMI Control-compatible connected
Once you have finished all connections and
settings, you must:
components in order to make use of the HDMI
Control function. For more information see the
operating instructions for each component.
1
Put all components into standby mode.
2
Turn the power ON for all components,
with the power for the Flat Screen TV being
turned on last.
Setting the HDMI Control mode
Choose whether to set this unit’s HDMI Control
function On or Off. You will need to set it to
Control On to use the HDMI Control function.
3
Choose the HDMI input to which the TV is
connected to this unit, and see if video
output from connected components displays
properly on the screen or not.
• When using a TV not manufactured by
Pioneer, put this setting to Control Off.
SETUP
Synchronized amp mode
Synchronized amp mode begins once you
carry out an operation for the Flat Screen TV.
For more information, see the operating
instructions of your Flat Screen TV.
1
2
Press SETUP.
TOOLS
ENTER
Select ‘HDMI Setup’ then press
Select ‘HDMI Ctrl’, then press
Adjust the setting then press
ENTER
.
Synchronized amp mode operations
The synchronized amp mode can be used to
perform the following operations when using
the iPod function, or when the HDMI cable is
used to connect an external component:
ENTER
3
ENTER
.
• Displays on the Flat Screen TV when you
mute or adjust the volume of this unit.
ENTER
4
• The input of this unit is automatically
changed when playback occurs on a
connected component.
ENTER to confirm.
• Control On – Enables the HDMI Control
function. When this unit’s power is turned
off and you have a supported source begin
playback while using the HDMI Control
function, the audio and video output from
the HDMI connection are output from the
Flat Screen TV.
• Even if you change this unit’s input to a
device that is not connected by HDMI, the
synchronized amp mode remains in effect.
Canceling synchronized amp mode
If you cancel synchronized amp mode while
connected via HDMI to a Flat Screen TV or
while you are watching a TV program, the
power for this unit is turned off.
• Control Off – The HDMI Control is
disabled. Synchronized operations cannot
be used. When this unit’s power is turned
off, audio and video of sources connected
via HDMI are not output.
However, the power remains ON when an input
other than HDMI is selected (including iPod
function).
55
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Additional information
Chapter 11
Additional information
ENTER
Optional system settings
2
Adjust the setting, then press
All the available settings in the System Setup
menu are listed below. See the notes in each
section for more information about the
settings. The first setting in each section is the
default.
ENTER to confirm the settings and exit.
• Sleep On – Switches off after about an
hour. The
indicator lights.
• Sleep Off – Cancels the sleep timer.
After selecting Sleep On, you can press SLEEP
again to check how much time is left. Each line
indicates approximately 12 minutes
(remaining):
SETUP
1
Press SETUP.
TOOLS
ENTER
S l e e p - - - - -
2
Select ‘System Setup’ then press
ENTER
.
Dimming the display
You can adjust the brightness of the text in the
front panel display.
ENTER
3
3
Choose the setting you want to
adjust, then press ENTER
.
The available settings are shown in the front
panel display.
ENTER
1
1
Select ‘Dimmer’ from the System
Setup menu, then press ENTER
.
ENTER
4
Adjust the setting, then press
ENTER
ENTER to confirm the settings and exit.
2
Adjust the setting, then press
ENTER to confirm the settings and exit.
• Dimmer Light – Brighter setting
Setting the sleep timer
The sleep timer switches off the system after
about an hour so you can fall asleep without
worrying about it.
• Dimmer Dark – Darker setting
2
ENTER
1
Select ‘Sleep Timer’ from the
System Setup menu, then press ENTER
.
Note
1 The setup menu is exited automatically after 5 minutes of inactivity.
2 The display dims when the sleep timer is set.
3 The display of the front panel dims when the sleep timer is set, regardless of this setting.
56
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
11
Changing the display mode
Setting up the remote to control
your TV
If no operation is performed for one minute, the
front panel display and button illumination
automatically turns off. The display will turn on
again automatically if a command is input or
movement is detected by the motion sensor.
You can use the supplied remote to control
your TV. To be able to use this feature you first
have to program the remote with a maker code
from the following table.
To make the display remain on constantly, set
the display mode to Display On.
1
4
2
5
8
0
3
6
9
7
ENTER
CLEAR
1
Press and hold CLEAR and Use
1
Select ‘Display Mode’ from the
the number buttons to input the maker code
for your TV, and press ENTER
System Setup menu, then press ENTER
.
.
See the following table for the list of maker
codes. If there is more than one code given for
your make, input the first one in the list.
ENTER
2
Adjust the setting, then press
ENTER to confirm the settings and exit.
• If the maker’s name of your TV doesn’t
appear in the table, you will not be able to
use this remote to control your TV.
• Auto Display – Turns off automatically if
no operation is performed for one minute.
• Display On – Displays constantly.
2
Point the remote towards your TV and
Even when set to not display, the display is
temporarily shown when you carry out a
control function.
press TV Control to check that the remote
works with your TV.
If the remote is set up correctly, the TV should
switch off. If it doesn’t and there is another
code given for your maker, repeat step 1 with a
new code.
• The motion sensor detects movement in
the left/right and up/down directions
within a distance of 2.5 m and an angle of
40º (20º only in the upper direction).
Walking towards the unit will reduce the
sensing range to 0.7 m.
Key lock setting
ENTER
1
Select ‘Key Lock’ from the System
Setup menu, then press ENTER
.
ENTER
2
Adjust the setting, then press
ENTER to confirm the settings and exit.
• Lock On – Makes the front panel buttons
and controls inoperative.
• Lock Off – Restores regular use of the front
panel buttons and controls.
57
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Additional information
TV Preset code list
Surround sound formats
Please note that there are cases where only
certain functions may be controllable after
assigning the proper preset code, or the codes
for the manufacturer in the list will not work for
the model that you are using.
Below is a brief description of the main
surround sound formats you’ll find on DVDs,
satellite, cable and terrestrial broadcasts, and
video cassettes.
Manufacturer Code(s)
Dolby
Aiwa 660
Alba 639
Bush 647
Fisher 635, 638
Fujitsu 648
Funai 640, 658
The Dolby technologies are explained below.
See www.dolby.com for more detailed
information.
GE 611, 628
General 629
Goldstar 610, 623, 650
Grandiente 630
Grundig 631, 653
Hitachi 606, 624, 625, 633, 634, 654
ITT 642
JVC 613
Dolby Digital
Dolby Digital is a multichannel digital audio
coding system widely used in cinemas, and in
the home for DVD and digital broadcast
soundtracks. It can deliver up to six discrete
audio channels, comprising five full range
channels and a special LFE (low frequency
effects) channel used mainly for deep,
rumbling sound effects; hence the term “5.1-
channel” Dolby Digital.
Magnabox 612
Mitsubishi 609
NEC 659
Nokia 632, 652
Panasonic 608, 622
Philips 607, 656, 668
RCA 601, 615, 616, 617, 618, 661, 662
Salora 643
Samsung 644, 646, 669, 670
Sanyo 614, 621, 645
SEI 649
In addition to the format features above, Dolby
Digital decoders offer downmixing for
Sharp 602, 619, 627, 667
Sony 604
compatibility with mono, stereo and Dolby Pro
Logic audio from a number of bit rates and
channels. Another feature, called Dialog
Normalization, attenuates programs based on the
average level of dialog in a program relative to its
peak level (also known as Dialnorm) in order to
achieve uniform playback level.
Tandy 641
Telefunken 637
Thomson 636, 663
Toshiba 605, 626
Uniden 671
Zenith 603, 620
Pioneer 600, 651
Dolby Pro Logic II and Dolby Surround
Using the innovative “steering logic” circuit,
this system extracts surround sound from
sources as follows:
• Dolby Pro Logic – 4.1 channel sound
(mono surround) from any stereo source
58
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
11
• Dolby Pro Logic II – 5.1 channel sound
(stereo surround) from any stereo source
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Surround
are registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-2007
DTS, Inc. All Rights Reserved.
With two channel sources, the “.1” subwoofer
channel is generated by bass management in
the receiver.
Dolby Surround is an encoding system which
embeds surround sound information within a
stereo soundtrack, which a Dolby Pro Logic
decoder can then use for enhanced surround
listening with greater sound detail.
Installation and maintenance
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic and the double-D
symbol are trademarks of Dolby Laboratories.
Hints on installation
We want you to enjoy using this system for
years to come, so please bear in mind the
following points when choosing a location:
DTS
Do...
The DTS technologies are explained below. See
www.dtstech.com for more detailed
information.
Use in a well-ventilated room.
Place on a solid, flat, level surface, such as a
table, shelf or stereo rack.
Don’t...
Use in a place exposed to high temperatures or
humidity, including near radiators and other
heat-generating appliances.
Place on a window sill or other place where the
system will be exposed to direct sunlight.
Use in an excessively dusty or damp
environment.
Place directly on top of an amplifier, or other
component in your stereo system that becomes
hot in use.
Use near a television or monitor as you may
experience interference — especially if the
television uses an indoor antenna.
DTS Digital Surround
DTS Digital Surround is a 5.1-channel audio
coding system from DTS Inc. now widely used
for DVD-Video, DVD-Audio, 5.1 music discs,
digital broadcasts, and video games. It can
deliver up to six discrete audio channels,
comprising five full range channels, including
an LFE channel. Higher sound quality is
achieved through the use of a low compression
rate, and high rates of transmittance during
playback.
Use in a kitchen or other room where the system
may be exposed to smoke or steam.
Use on a thick rug or carpet, or cover with cloth
— this may prevent proper cooling of the system
unit.
Place on an unstable surface, or one that is not
large enough to support all four of the system
unit’s feet.
59
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
• If the system does not operate normally due to external effects such as static electricity
disconnect the plug from the outlet and insert again to return to normal operating conditions.
• For audio-related problems, please also check the settings of the audio playback device. See
the operating instructions for the device for detailed information.
General
Problem
Remedy
The power does not turn • Leave the unit plugged in, wait for one minute, then switch back on.
on, or switches off
suddenly (an error
message may be
• Make sure there are no loose strands of wire touching the unit. This could cause
the system to shut off automatically.
• Check that the speakers are connected correctly.
displayed at startup). Or, • Make sure there is enough space for ventilation around the unit.
the display disappears • Make sure the voltage of the mains power source is correct for the model.
suddenly and no sound • Try reducing the volume level.
is output.
• If the problem persists, take it to your nearest Pioneer authorized service center
or your dealer for servicing.
• Do not block the air intake opening on the bottom as well as the air exhaust
opening on the back of this unit.
No sound is output
• If you’re using the line input, make sure the component is connected correctly
when an input function and the volume level of your external component (i.e. a portable player, etc.) is
is selected.
adjusted (see Listening to the sound of an external device on this receiver on
page 47).
• Turn up the volume.
• No audio is output from the speakers connected to this unit if HDMI Audio is set
to TV (page 51).
• No audio is output if a DVI component is connected via HDMI.
• Press MUTE on the remote control to turn muting off.
No sound from surround • Refer to Channel level setting on page 43 to check the speaker levels.
or center speakers.
• Check that you haven’t selected the Auto, Stereo, A.L.C. or Virtual mode (see
Listening in surround sound on page 31).
• Connect the speakers properly (see Basic connections on page 26).
• Confirm audio output and HDMI settings for the external component
connected by optical digital cable, coaxial digital cable, or HDMI cable.
• If the source is 88.2 kHz/96 kHz, it will be played in stereo.
60
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
11
Problem
Remedy
No audio signal is
output from AUDIO
OUT jacks.
• Audio input from ANALOG RCA jacks cannot be output from AUDIO OUT
jacks.
No sound from
subwoofer.
• Check the speaker level settings (see Channel level setting on page 43).
• SX-LX08 model only:
– Check subwoofer for correct connections (see Connect the speakers on
page 24).
– Be sure subwoofer's power is turned ON.
– Raise subwoofer's volume level.
Can’t operate using the • Replace the batteries (see Putting the batteries in the remote control on page 9).
remote control.
• Operate within 7 m, 30° of the remote sensor (see Using the remote control on
page 9).
• Remove any obstacles or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct light.
• Check that there’s nothing mistakenly plugged into the CONTROL IN jack.
• For operating the other Pioneer component connected to the CONTROL OUT
jack of this unit, make sure that the control cable and either an HDMI or analog
audio cable are connected (page 49).
• If an object is placed on top of the touch sensor, the sensor will be activated, thus
disabling the remote control unit operations. If the action indicator remains
continuously lighted, remove any object sitting on the touch sensor panel.
The front panel display
and indicators do not
appear.
• If the display mode is set to Auto Display, the display will automatically turn off
if no operation is performed for a period of one minute. Try performing an
operation.
Motion sensor not
working.
• The motion sensor is on the front of the unit. Make sure you are within 2.5 m and
40° of the sensor.
• Since the motion sensor uses infrared rays, it may not work correctly if placed in
direct sunlight or close to heat source.
• Minimum unit height must be 25 cm or above from ground level. The sensor will
not work properly when located at ground level.
• Motion sensor will not work if placed in a fully sealed cabinet (include glass /
clear cabinet).
61
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Additional information
Tuner
Problem
Remedy
Considerable noise in
radio broadcasts.
• Connect the AM antenna (see Basic connections on page 26) and adjust the
direction and position for best reception. You may also connect an additional
internal or external AM antenna (refer to Connecting external antennas on
page 49).
• Fully extend the FM wire antenna, position for best reception, and secure to a
wall. You may also connect an outdoor FM antenna (see Connecting external
antennas on page 49).
• Turn off other equipment that may be causing the noise or move it further away.
Auto tuning does not
pick up some stations.
• The radio signal is weak. Auto tuning will only detect radio stations with a good
signal. For more sensitive tuning, connect an outdoor antenna.
HDMI connection
Symptom
Remedy
No picture or sound.
• This unit is HDCP-compatible. Check that the components you are connecting
are also HDCP-compatible.
• Depending on the connected source component, it’s possible that it will not
work with this unit (even if it is HDCP-compatible).
• If the problem still persists when connecting your HDMI component directly to
your monitor, please consult the component or monitor manual or contact the
manufacturer for support.
No sound, or sound
suddenly ceases.
• Check that the HDMI Audio is set to AMP.
• If the component is a DVI device, use a separate connection for the audio.
• Check the audio output settings of the source component.
HDMI Control does not • Verify that the HDMI cable is firmly connected.
function. • Make sure that this unit’s HDMI Control mode is set to Control On (page 55).
• Check whether the connected component supports HDMI Control or not. For
more information refer to the operating manual of your Flat Screen TV, DVD player,
Blu-ray disc player, etc.
• This unit does not guarantee HDMI Control-compatible components other than
those made by Pioneer.
Front panel display messages
Message
Description
An operation is prohibited because the source is 176.4 kHz/192 kHz PCM.
192kHz PCM
2ch Only
An operation is prohibited because it is only applicable to 2 channel sources, while
the current source is a multichannel source.
An operation is prohibited because the source is 88.2 kHz/96 kHz PCM.
96kHz PCM
62
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
11
Message
Description
An error occurred during MCACC setup because the microphone is not connected
or is not connected properly.
Error MIC!
An error occurred during MCACC setup because the speakers are not connected or
are not connected properly.
Error Speaker!
When performing MCACC setup, no sound could be detected from subwoofer.
Confirm that the subwoofer's power switch is set to ON, and raise subwoofer sound
volume to comfortable level, then press ENTER once again.
Error SW!
(SX-LX08 model only)
Appears when a menu is automatically exited after a set period of inactivity.
Exit
Displays when you change the listening mode, the volume level, or some sound
settings when the HDMI Audio is set to TV.
HDMI Audio <TV>
Check if the HDMI cable is properly connected. If the cable is properly connected,
this unit may be damaged. In such an event, please contact a Pioneer-authorized
service center or your nearest dealer.
HDMI C.ERR 1**
HDCP ERROR
Check whether or not the connected component is compatible with HDCP. Some
components that are compatible with HDCP still cause this message to be
displayed, but so long as there is no problem with displaying video, this is not a
malfunction.
The key lock is enabled. See Key lock setting on page 57.
Operation is disabled since Line Output is set to Lt/Rt.
Key Lock
Line Out Mode
Muting
When audio is muted, display appears if Auto MCACC setup is performed.
Display appears when Auto MCACC setup is performed without a microphone
connected.
No MIC
Background noise is too high to complete MCACC setup successfully.
Try adjusting the resolution, DeepColor or other setting for your component.
Noisy!
Not support
Check whether the speaker cables are short-circuited. If the error message
continues to be displayed, contact your Pioneer authorized service center or your
dealer for servicing.
OC Error1
OC Error2
Try lowering the volume. If this problem is not fixed by removing and inserting the
power cable, this unit may be damaged. In such an event, please contact a Pioneer-
authorized service center or your nearest dealer.
Over Temp
An operation is prohibited because the headphones are connected.
Phones In
Contact your Pioneer authorized service center or your dealer for servicing.
*** BackUpERR
63
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Additional information
Resetting the system
Display Mode
Line Output
Display Mode
Line Output
TV Input
Use this procedure to reset all system settings
to the factory default.
TV Input
HDMI Audio
HDMI Control mode
Auto Delay
HDMI Audio
HDMI Ctrl
Auto Delay
-
SETUP
1
2
3
4
Press SETUP.
TOOLS
Storing stations
ENTER
Select ‘Initialize’ then press ENTER
.
ENTER
Select ‘All Init’ then press ENTER
.
• Initialize OK? is displayed.
ENTER
Press ENTER to confirm initialization.
The system will restart and all the system
settings should be reset.
• Note that following settings will be saved,
even if the receiver is unplugged.
Input function
Listening mode
Sound Retriever
‘HDMI 1’
,
‘Digital 1’, etc.
‘Auto’ ‘Action’, etc.
,
‘Retriever On’ or
‘Retriever Off’
Sound Field
Sound Field
Tone controls
Bass, Treble, Quiet,
Midnight
Bass Mode
Bass Mode
Dialogue
Dialogue Enhancement
Acoustic Calibration EQ MCACC EQ
Sound Delay
Sound Delay
Center Width
Dimension
Panorama
Channel Level
Distance
Center Width
Dimension
Panorama
Channel Level
Speaker Distance
Dynamic Range Control
Dual Mono
D.R.C.
Dual Mono
Virtual SB
LFE ATT
Virtual Surround Back
LFE Attenuator
CD Type
CD Type
64
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
11
Speaker system
(Front speakers x2, Center speakers x2, Surround
speakers x2, Subwoofer x1)
Specifications (LX03BD model)
Audio Multi-channel Receiver
•
Front speakers
Enclosure . . . . . . . . . Closed-box bookshelf type
•
Amplifier section
(magnetically shielded)
System. . . . . . . . . . . . . . . . . . . . . . . 2-way system
Speakers:
Woofer. . . . . . . . . . . . . . . .5.2 cm cone type x2
Tweeter . . . . . . . . . . . .2.6 cm semi-dome type
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω
Frequency range . . . . . . . . . . . 200 Hz to 20 kHz
Maximum input power. . . . . . . . . . . . . . . . 100 W
Dimensions
RMS Power Output:
Front, Center . . . . . . . . . . . 100 W per channel
(1 kHz, 10 % T.H.D., 4 Ω)
Surround . . . . . . . . . . . . . . . . 50 W per channel
(1 kHz, 10 % T.H.D., 8 Ω)
Subwoofer . . 100 W (100 Hz, 10 % T.H.D., 4 Ω)
•
FM tuner section
Frequency range . . . . . . . . 87.5 MHz to 108 MHz
Antenna . . . . . . . . . . . . . . . . . . 75 Ω, unbalanced
. . . . . . .80 mm (W) x 196.8 mm (H) x 82 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.02 kg
•
AM tuner section
Frequency range . . . . . . . . . 531 kHz to 1602 kHz
Antenna . . . . . . . . . . . . . . . . . . . . . Loop antenna
•
Center speakers
Enclosure . . . . . . . . . Closed-box bookshelf type
(magnetically shielded)
•
Input/Output section
System. . . . . . . . . . . . . . . . . 5.2 cm 1-way system
Speakers . . . . . . . . . . . . . . . . . . 5.2 cm cone type
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Frequency range . . . . . . . . . . . 200 Hz to 20 kHz
Maximum input power. . . . . . . . . . . . . . . . . 50 W
Dimensions
HDMI terminal:
Input . . . . . . . . . . . . . . . . . . . . . . . . . . 19-pin x2
Output. . . . . . . . . . . . . . . . . 19-pin (5 V, 55 mA)
Audio input. . . . . .Coaxial x1, Optical x2 (Digital)
RCA (2-pin) (Analog)
Audio output . . . . . . . . . . . RCA (2-pin) (Analog)
Control jack . . . . Input x1, Output x1 (Mini jack)
MCACC input . . . . . . . . . . . . . . . . . . . . . Mini jack
iPod connector. . . . . . . . . . . . . . . . . . 5 V, 500 mA
. . . . . . . . . 80 mm (W) x 80 mm (H) x 82 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.48 kg
•
Surround speakers
Enclosure . . . . . . . . . Closed-box bookshelf type
•
Miscellaneous
(magnetically shielded)
System. . . . . . . . . . . . . . . . . . . . . . . 2-way system
Speakers:
Woofer. . . . . . . . . . . . . . . . . . 5.2 cm cone type
Tweeter . . . . . . . . . . . .2.6 cm semi-dome type
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω
Frequency range . . . . . . . . . . . 200 Hz to 20 kHz
Maximum input power. . . . . . . . . . . . . . . . . 50 W
Dimensions
Power requirements
. . . . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . .55 W
Power consumption in standby
. . . . . . . . . . . . . . . . . . . 0.7 W (HDMI Control ON)
0.4 W (HDMI Control OFF)
Dimensions
. . . . . . . .420 mm (W) x 80 mm (H) x 364 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8 kg
. . . . . . .80 mm (W) x 115.8 mm (H) x 82 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.60 kg
65
En
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Additional information
•
Subwoofer
Enclosure. . . . . . . Bass-reflex floorstanding type
System . . . . . . . . . . . . . . . . . 18 cm 1-way system
Speaker . . . . . . . . . . . . . . . . . . . 18 cm cone type
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω
Frequency range . . . . . . . . . . . 25 Hz to 1500 Hz
Maximum Input Power. . . . . . . . . . . . . . . . 100 W
Dimensions
Specifications (SX-LX08 model)
•
Amplifier section
RMS Power Output:
Front, Center . . . . . . . . . . . . 100 W per channel
(1 kHz, 10 % T.H.D., 4 Ω)
Surround . . . . . . . . . . . . . . . . 50 W per channel
(1 kHz, 10 % T.H.D., 8 Ω)
. . . . . . 211 mm (W) x 320 mm (H) x 358 mm (D)
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.50 kg
•
FM tuner section
Frequency range . . . . . . . . 87.5 MHz to 108 MHz
Antenna . . . . . . . . . . . . . . . . . .75 Ω, unbalanced
Accessories
•
Receiver box:
•
AM tuner section
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6 dry cell batteries
Frequency range . . . . . . . . . 531 kHz to 1602 kHz
Antenna . . . . . . . . . . . . . . . . . . . . . Loop antenna
(to confirm system operation) . . . . . . . . . . . . . . 2
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . 1
FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Microphone (for Auto MCACC setup). . . . . . . . 1
Power cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
HDMI cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Speaker cable adaptors
(White, Red, Blue, Grey, Purple) . . . . . . . .1 each
Cleaning cloth. . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Setup Guide
•
Input/Output section
HDMI terminal:
Input . . . . . . . . . . . . . . . . . . . . . . . . . . 19-pin x2
Output. . . . . . . . . . . . . . . . . 19-pin (5 V, 55 mA)
Audio input. . . . . .Coaxial x1, Optical x2 (Digital)
RCA (2-pin) (Analog)
Audio output . . . . . . . . . . . RCA (2-pin) (Analog)
Subwoofer Pre Out . . . . . . . . . . . . . . . . . .RCA x1
Control jack . . . . Input x1, Output x1 (Mini jack)
MCACC input . . . . . . . . . . . . . . . . . . . . . Mini jack
iPod connector. . . . . . . . . . . . . . . . . . 5 V, 500 mA
These operating instructions
•
Miscellaneous
•
Speakers box:
Power requirements
Speaker cables . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Brackets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Screws (for brackets) . . . . . . . . . . . . . . . . . . . . . 4
Speaker stands . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Non-skid pads (for satellite speakers). . . . . . . 24
Non-skid pads (for subwoofer). . . . . . . . . . . . . . 4
Non-skid pads (for speaker stands). . . . . . . . . . 8
Spiral wrap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . AC 220 V to 240 V, 50 Hz/60 Hz
Power consumption . . . . . . . . . . . . . . . . . . .55 W
Power consumption in standby
. . . . . . . . . . . . . . . . . . . 0.7 W (HDMI Control ON)
0.4 W (HDMI Control OFF)
Dimensions
. . . . . . . .420 mm (W) x 80 mm (H) x 364 mm (D)
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8 kg
Note
Specifications and design subject to possible
modification without notice, due to
improvements.
66
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
11
Accessories
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AA/R6 dry cell batteries
(to confirm system operation) . . . . . . . . . . . . . . 2
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . 1
FM antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Microphone (for Auto MCACC setup) . . . . . . . . 1
Power cords . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
HDMI cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Speaker cable adaptors
(White, Red, Green, Blue, Grey) . . . . . . . . 1 each
Cleaning cloth . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Setup Guide
These operating instructions
Note
• Specifications and design subject to
possible modification without notice, due
to improvements.
67
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Two
BDP-LX08
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Two
Contents
Section Two
04 Playback
Playing discs or files . . . . . . . . . . . . . . . . .90
Forward and reverse scanning . . . . . . . .91
Playing specific titles, chapters or
01 Before you start
Types of discs/files that can be played . . . 71
Playable discs . . . . . . . . . . . . . . . . . . . . 71
Playable files . . . . . . . . . . . . . . . . . . . . . 74
tracks . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Skipping content. . . . . . . . . . . . . . . . . . .91
Playing in slow motion . . . . . . . . . . . . . .92
Step forward and step reverse. . . . . . . . .92
Switching the camera angles . . . . . . . . .92
Switching the subtitles . . . . . . . . . . . . . .93
Switching the audio streams/channels . . .93
Switching the secondary audio . . . . . . . .94
Switching the secondary video . . . . . . . .94
Displaying the disc information. . . . . . . .95
Using the Play Mode functions . . . . . . . . .95
Playing from a specific time
02 Player connections
Connecting a TV. . . . . . . . . . . . . . . . . . . . 76
Connecting using the HDMI cable
included with this receiver. . . . . . . . . . . 76
Connecting to a TV with no
HDMI input . . . . . . . . . . . . . . . . . . . . . . 79
Connecting the other audio component . . . 80
Connecting using audio cables . . . . . . . 80
Connecting the power cord . . . . . . . . . . . 82
(Time Search) . . . . . . . . . . . . . . . . . . . . .95
Playing a specific title, chapter or track
(Search) . . . . . . . . . . . . . . . . . . . . . . . . .96
Playing a specific section within a title or
track repeatedly (A-B Repeat) . . . . . . . . .96
Playing repeatedly (Repeat Play) . . . . . . .97
Playing in random order (Random Play). . .98
About Play Mode types . . . . . . . . . . . . . .99
Playing from the Home Media Gallery . . .100
Playing discs. . . . . . . . . . . . . . . . . . . . .100
Playing movie files . . . . . . . . . . . . . . . .100
Playing music files . . . . . . . . . . . . . . . .102
Playing in the desired order
03 Getting Started
Making settings using
the Setup Navigator menu . . . . . . . . . . . . 83
Using the TOOLS menu . . . . . . . . . . . . . . 86
Erasing the additional data from
BD-ROMs. . . . . . . . . . . . . . . . . . . . . . . . . 87
Switching the video output terminal. . . . . 87
Switching the output video resolution . . . 87
(HMG Playlist). . . . . . . . . . . . . . . . . . . .103
69
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Section Two
05 Adjusting audio and video
Adjusting the video . . . . . . . . . . . . . . . . .105
Adjusting the Audio DRC. . . . . . . . . . . . .107
06 Advanced settings
Changing the settings (Initial Setup) . . . .108
Operating the Initial Setup screen. . . . .108
Changing to other language at
language setting . . . . . . . . . . . . . . . . . .114
Changing the speaker setup . . . . . . . . .114
Adjusting the output level of the various
speakers (Channel Level). . . . . . . . . . . .115
Registering or Changing the password . .116
Changing the Age Restriction for
watching BD-ROMs. . . . . . . . . . . . . . . .117
Changing the Parental Lock level for
watching DVDs. . . . . . . . . . . . . . . . . . .117
Changing the Country/Area code . . . . .119
Changing the terminals for outputting
video and audio signals
(Output Terminal Priority) . . . . . . . . . . .119
Restoring all the settings to the factory
default settings . . . . . . . . . . . . . . . . . . .120
About the audio output settings . . . . . .121
07 Additional information
Troubleshooting. . . . . . . . . . . . . . . . . . . .123
Playback . . . . . . . . . . . . . . . . . . . . . . . .123
When connected using
an HDMI cable . . . . . . . . . . . . . . . . . . .127
Others . . . . . . . . . . . . . . . . . . . . . . . . . .128
Language Code Table and Country/
Area Code Table. . . . . . . . . . . . . . . . . . . .130
Language Code Table . . . . . . . . . . . . . .130
Country/Area Code Table. . . . . . . . . . . .131
70
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
01
Chapter 1
Before you start
Types of discs/files that can be played
Playable discs
Discs with the logo marks below indicated on the disc label, package or jacket can be played.
Application format
CD-DA
DTS-CD
DATA-
Disc type
Logo
DVD-
Video
1
BDAV
DVD VR
BDMV
2
DISC
BD-ROM
BD-R
BD-RE
DVD-ROM
DVD-R
DVD-R DL
(Dual Layer)
DVD-RW
DVD+R
DVD+RW
CD-DA
(Music CD)
CD-R
CD-RW
CD-ROM
1. Including the AVCHD format.
2. Discs on which movie files or music files are recorded.
71
En
Download from Www.Somanuals.com. All Manuals Search And Download.
01
Before you start
To enjoy the surround sound of Dolby TrueHD,
Dolby Digital Plus, DTS-HD Master Audio and
DTS-HD High Resolution Audio, it is
recommended to connect the player to an AV
receiver or amplifier compatible with these audio
formats using an HDMI cable. After loading a BD
containing sound in one of these audio formats,
select the audio format on the menu screen.
Discs that cannot be played
• HD DVDs
• DVD Audio discs
• DVD-RAM discs
• Non-finalized DVD-R/DVD-RW/DVD+R/
DVD+RW discs in the DVD-Video format
and AVCHD format
• Non-finalized Dual Layer DVD-R discs in
the DVD VR format
When connected to this receiver, these audio
signals are converted to PCM and output from
the HDMI jack.
• SACDs
See About the audio output settings on
page 121 for the output conditions of the
different formats.
• Video CDs
• SVCDs
“Blu-ray Disc” and
are trademarks.
is a trademark of DVD Format/Logo
Licensing Corporation.
Note
• Some discs cannot be played, even if one of
the above logo marks is indicated.
• To play 8 cm discs, set the disc in the 8 cm
disc depression in the center of the disc
tray. No adapter is necessary. 8 cm BD-
ROMs cannot be played.
About audio formats
The following audio formats are supported on
this player:
• Dolby TrueHD
• Dolby Digital Plus
• Dolby Digital
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
• DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
• MPEG
• MPEG-2 AAC
• Linear PCM
72
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
01
– Blu-ray Disc Rewritable (RE) Format
Version 2
• Dual Layer BDs can be played.
• Movie and music files recorded on BDs
cannot be played.
Manufactured under license under U.S. Patent
#: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS is a registered trademark
and the DTS logos, Symbol, DTS-HD and DTS-
HD Advanced Digital Out are trademarks of DTS,
Inc. © 1996-2007 DTS, Inc. All Rights Reserved.
• 8 cm BD-ROMs cannot be played.
Playing DVDs
• DVD-Video can be played.
• DVD-R/-RW/+R/+RW discs recorded in the
DVD-Video format can be played (finalize
them before playing them on this player).
• DVD-R/-RW discs recorded in the VR format
(Video Recording format) can be played.
Playing BDs
• BDs (BDMV) compatible with the formats
• This label indicates playback compatibility
with DVD-RW discs recorded in VR format
(Video Recording format). However, for
discs recorded with a record-only-once
encrypted program, playback can only be
achieved using a CPRM compatible device.
below can be played.
– Blu-ray Disc Read-Only (ROM) Format
Version 2
– Blu-ray Disc Recordable (R) Format
Version 2
– Blu-ray Disc Rewritable (RE) Format
Version 3
This player supports BD-ROM Profile 1
Version 1.1. BONUSVIEW Functions such
as playback of secondary video (Picture-in-
Picture) and secondary audio can be used.
For details on secondary video and
secondary audio playback, refer to the
disc’s instructions.
• DVDs recorded in the AVCHD format can
be played (finalize them before playing
them on this player).
“AVCHD” and the “AVCHD” logo are
trademarks of Matsushita Electric Industrial
Co., Ltd. and Sony Corporation.
“BONUSVIEW” is trademark of Blu-ray Disc
Association.
• Movie and music files recorded on DVD-R/
-RW/+R/+RW discs can be played. See
Playable files on page 74.
When a BD-ROM is played, additional data
may be stored in the player’s memory area
(local storage). If the message indicating
low memory (local storage) appears, erase
the BDMV data (page 87).
• Dual Layer DVDs can be played. However,
non-finalized Dual Layer DVD-R discs
recorded in the VR format cannot be played
(finalize them before playing them on this
player).
• BDs (BDAV) compatible with the formats
below can be played.
• HD DVD, DVD Audio and DVD-RAM discs
cannot be played.
– Blu-ray Disc Recordable (R) Format
Version 1
73
En
Download from Www.Somanuals.com. All Manuals Search And Download.
01
Before you start
The non-DVD, audio side of the disc is not
compatible with this player.
About region numbers
Blu-ray Disc Player and BD-ROM or DVD-Video
discs are assigned region numbers according
to the region in which they are sold.
It is possible that when loading or ejecting a
DualDisc, the opposite side to that being
played will be scratched. Scratched discs may
not be playable.
This player’s region numbers are:
• BD-ROM: B
For more detailed information on the DualDisc
specification, please refer to the disc
manufacturer or disc retailer.
• DVD-Video: 2
Discs not including these numbers cannot be
played. Discs playable on this player are as
shown below.
Playing discs created on computers
• It may not be possible to play DVD-R/-RW
or CD-R/-RW discs recorded using a
personal recorder or computer. (This can
be due to various reasons, including disc
properties, scratches, dirt on the disc, dirt
on the player’s lens, condensation and so
on.)
• BDs: B (including B) and ALL
• It may not be possible to play discs
recorded using a computer due to the
application settings or environment.
Record discs in the proper format. For
details, contact the dealer.
• DVDs: 2 (including 2) and ALL
Playing CDs
• Music CDs (CD-DAs and DTS-CDs) can be
played.
Playable files
Movie and music files recorded on DVDs and
CDs can be played.
• Movie and music files recorded on CDs can
be played. See Playable files below.
Caution
• SACD, Video CD and Super VCD discs
cannot be played.
• In DVD, only the one recorded by the ISO
9660 file system can be played.
• Regarding copy protected CDs: This player
is designed to conform to the
• Some files may not be playable.
specifications of the Audio CD format. This
player does not support the playback or
function of discs that do not conform to
these specifications.
• For some files, it may not be possible to use
certain functions during playback.
• It may not be possible to play some files,
even if they have the extension of a file
playable on this player.
DualDisc playback
• Files protected by DRM (Digital Rights
Management) cannot be played (not
including DivX VOD files).
A DualDisc is a new two-sided disc, one side of
which contains DVD content — video, audio,
etc. — while the other side contains non-DVD
content such as digital audio material.
The DVD side of a DualDisc will be played on
this player (excluding any DVD-Audio content).
74
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you start
01
– DivX VOD files for which the player’s
DivX VOD registration code is not
authorized cannot be played
Supported movie file formats
• DivX
DivX is a media technology created by
DivX., Inc. DivX media files contain not only
video but also advanced media features
like subtitles and alternate audiotracks,
etc.
(Authorization Error is displayed).
– The number of views is restricted for
some DivX VOD files. When such files
are played on this player, the remaining
number of views is displayed. Files for
which the remaining number of views
has reached 0 cannot be played (Rental
Expired is displayed). Files for which the
number of views is not restricted can be
played as many times as you like (the
remaining number of views is not
displayed).
Conform to the size under 720 x 576 pixels/
720 x 480 pixels.
DivX files encoded with GMC/Qpel option
cannot be played.
Only audio signals with MP3 or Dolby
Digital (AC3) format are output.
Note that files other than the ones
containing DivX video cannot be played,
even if they have the extension “.avi”.
Supported music file formats
• Windows Media™ Audio 9 (WMA9)
Bit rate: Up to 192 kbps
Sampling frequencies: 22.05 kHz, 32 kHz,
44.1 kHz and 48 kHz
Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or
other countries.
®
Official DivX Certified product.
®
Plays all versions of DivX video (including
DivX 6) with standard playback of DivX
®
®
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
media files.
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under
license.
• MPEG-1 Audio Layer 3 (MP3)
Bit rate: Up to 320 kbps
Note
Sampling frequencies: 8 kHz, 11.025 kHz,
12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz,
44.1 kHz and 48 kHz
• DivX VOD files are protected by DRM. They
can only be played on registered devices.
– You may be requested by the file
distributor to input the DivX VOD
registration code for authorization of the
player in order to play DivX VOD files.
This player’s DivX VOD registration code
can be checked at Initial Setup
Options DivX VOD Registration
Code (page 113).
Playable file extensions
• Movie files
.divx and .avi
• Music files
.wma and .mp3
75
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Player connections
CPhlaapteyr e2 r connections
Connecting a TV
Be sure to turn off the power and unplug the
power cord from the power outlet whenever
making or changing connections.
TV
To HDMI input terminal
Note
• Make the settings in the Setup Navigator
menu according to the type of cable
connected (page 83).
HDMI cable
(included)
ANALOG
L
Connecting using the HDMI cable
included with this receiver
OPTICAL
1
2
AM
LO
R
AUDIO IN
COAX
FM
UM
75
The audio and video signals can be transferred
to HDMI-compatible devices as digital signals
with no loss of sound or video quality. After
connecting, make the settings at the Setup
Navigator menu according to the connected
HDMI-compatible device (page 83).
DIGITAL IN
3
OUT
IN 2
IN 1
DIGITAL IN
HDMI
Receiver’s rear panel
HDMI cable
(included)
Also refer to the operating instructions of the
device being connected.
FRONT
SURROUND SURROUND BACK CENTER
L
VIDEO OUT
Y
R
VIDEO
Note
SUB WOOFER
AUDIO OUT
(
7.1 ch
)
PB
HDMI OUT
• The HDMI indicator on the player’s front
panel lights when an HDMI-compatible
device is connected. (Depending on the
connected device, in some cases it may
only light when the player is selected as the
device’s input.)
PR
OPTICAL
CONTROL DIGITAL
IN OUT
COMPONENT
S-VIDEO
VIDEO
Player’s rear panel
Direction of
signal flow
• 1080p video signals may not be output,
depending on the HDMI cable being used.
Caution
• Hold the plug when connecting and
disconnecting the cable.
• Placing a load on the plug could result in
faulty contact and no video signals being
output.
76
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Player connections
02
For details, see About the audio output settings
on page 121.
About HDMI
This player incorporates High-Definition
Multimedia Interface (HDMI™) technology.
About the HDMI high speed transmission
This player outputs 1080/50p, 1080/60p and
Deep Color video signals. If your TV supports
1080/50p, 1080/60p or Deep Color signals, use
a High Speed HDMI™ cable or the supplied
HDMI cable in order to take advantage of the
maximum performance the player and TV can
offer. Also set HDMI High-Speed
The player supports Deep Color. The
conventional players can transmit a video
signal with 8 bit color depth in the YCbCr 4:4:4
or RGB formats, the players supporting Deep
Color can transmit a video signal with a color
bit depth of greater than 8 bits per color
component. Subtle color gradations can be
reproduced when connected to a TV that
supports Deep Color.
Transmission to On (page 110).
High Speed HDMI™ cables are tested to carry
signals up to 1080p. 1080/50i, 1080/50p, 720/
50p, 1080/24p, 1080/60i, 1080/60p and 720/60p
video signals that are capable of Deep Color
can also be carried.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
Note
• Set HDMI High-Speed Transmission to
Off when using an HDMI cable other than
a High Speed HDMI™ cable (a Standard
HDMI™ cable).
Audio signals that can be transferred
with the player’s HDMI OUT terminal
• Dolby TrueHD
• The following restrictions apply when
HDMI High-Speed Transmission is set to
Off:
• Dolby Digital Plus
• Dolby Digital
– Deep Color signals are not output.
• DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
• MPEG-2 AAC
– If output video resolution is set to Auto
,
the signals are output with a resolution of
1080/50i or 1080/60i when TV’s preferred
resolution is 1080/50p or 1080/60p.
– When the output video resolution is set
to 576i/480i or 576p/480p, Dolby
TrueHD and DTS-HD Master Audio
signals are not output as such. They are
either output as Dolby Digital or DTS
Digital Surround signals or converted
into linear PCM. Also, 96 kHz and 192
kHz multi-channel linear PCM audio
signals cannot be output. They are
output as 2-channel signals (page 121).
• Linear PCM
Linear PCM audio signals meeting the
following conditions can be output:
– Sampling frequency: 32 kHz to 192 kHz
– Number of channels: Up to 8 (up to 6 for
a 192 kHz sampling frequency)
When outputting the bitstream of Dolby
TrueHD, Dolby Digital Plus, Dolby Digital, DTS-
HD Master Audio, DTS-HD High Resolution
Audio, DTS Digital Surround, MPEG or MPEG-
2 AAC, these audio signals output in linear
PCM from the HDMI terminal to this receiver.
• When an HDMI cable with a built-in
equalizer is connected, it may not operate
properly.
77
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Player connections
About HDCP
To use the HDMI Control function
• The HDMI Control function operates when
HDMI Control is set to On for all devices
connected with HDMI cables. Once
connections and the settings of all the
devices are finished, be sure to check that
the player’s picture is output to the Flat
Screen TV. (Also check after changing the
connected devices and reconnecting
HDMI cables.) The HDMI Control function
may not operate properly if the player’s
picture is not properly output to the Flat
Screen TV.
HDCP (High-bandwidth Digital Content
Protection) is a copyright protection system by
which digital video signals are encrypted.
When connected to a DVI device
• It is not possible to connect DVI devices
(computer displays, for example) that
are not compatible with HDCP.
• No audio signals are output. Connect
using an audio cable (included), etc.
• This player is designed for connection with
HDMI-compatible devices. When
connected to a DVI device, it may not
operate properly depending on the DVI
device.
• Use High Speed HDMI™ cables when
using the HDMI Control function. The
HDMI Control function may not operate
properly if other HDMI cables are used.
• The function name of KURO LINK used on
the web and in catalogs is referred to as
HDMI Control in the operating instructions
and on the player.
About HDMI Control function
• When the player is connected to a Pioneer
Flat Screen TV or this receiver, supporting
the HDMI Control function, it can be
operated from the Flat Screen TV or this
receiver.
About PQLS function
The PQLS (Precision Quartz Lock System) is a
transfer control technology using the HDMI
Control function. The player’s output signals
are controlled from the AV receiver or amplifier
to achieve high quality sound playback using
the quartz oscillator of AV receiver or amplifier.
This eliminates the influence of the jitter
generated upon transfer which can adversely
affect the sound quality.
• The Flat Screen TV’s input is switched
automatically when playback is started on
the player or the Home Menu or the Home
Media Gallery is displayed. When the input
is switched, the playback picture, the
Home Menu or the Home Media Gallery
appears on the Flat Screen TV (Auto-select
function). If the Flat Screen TV’s power is
being turned off at this time, it may turn on
automatically (Simultaneous power
function). When the language information
from a connected Flat Screen TV is
received, you can have the player’s on-
screen display language change
• The PQLS function is only activated when
the player is connected to a Pioneer AV
receiver or amplifier compatible with the
PQLS function via HDMI connection.
• The PQLS function is only activated when
playing a music CD (CD-DA).
automatically to that of the Flat Screen TV
(Unified language function). This function
is available only when playback is stopped
and the menu screen is not displayed.
• The PQLS function is activated when the
player is set as follows (page 111):
HDMI Control: On
• Also refer to the operating instructions of
the Flat Screen TV, etc.
PQLS: Auto
• Also refer to the operating instructions of
AV receiver or amplifier.
78
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Player connections
02
• If the output video resolution is switched
when playing a music CD (CD-DA), the
PQLS function does not work. This function
will work again after playback stops and
restarts.
Caution
• This receiver cannot use the PQLS
function.
Connecting to a TV with no HDMI input
TV
To video input
terminal
To S-Video input
terminal
To component video input
To audio input
terminals
terminals
FRONT
SURROUND SURROUND BACK CENTER
L
R
L
VIDEO OUT
VIDEO
AC IN
Y
R
SUB WOOFER
AUDIO OUT
(
2
ch
)
AUDIO OUT
(
7.1 ch
)
PB
HDMI OUT
PR
COMPONENT
OPTICAL
CONTROL DIGITAL
IN OUT
S-VIDEO
VIDEO
Player’s rear panel
HDMI cable
(included)
OPTICAL
1
2
AM
LOOP
FM
UMBAL
Direction of
signal flow
75
ANTENNA
DIGITAL IN
OUT
IN 2
IN 1
HDMI
Receiver’s rear panel
79
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Player connections
The video signal can also be connected using a
separately sold S-Video or component video
cable.
Note
• Make the settings in the Setup Navigator
menu according to the type of cable
connected (page 83).
Caution
• To output video signals from this player,
connect using one of the following (not
including when connected using an HDMI
cable): a component video cable
(commercially available), an S-Video cable
(commercially available) or a video cable
(included).
• When connected to the TV using a
component video cable (commercially
available), video signals are not output with
a resolution of 1080/50i, 1080/50p, 720/50p,
1080/24p or 1080/60p.
• Depending on the output video resolution
setting, the picture may not be output
(page 87).
Connecting using audio cables
• Video signals are output with a resolution
of 576/50i or 480/60i when connected using
a video cable (included) or an S-Video
cable (commercially available).
Caution
• For DTS-HD Master Audio and DTS-HD
High Resolution Audio signals, the DTS
Digital Surround signals are converted to
linear PCM for output (page 121).
• Connect the player’s video output
directly to your TV.
This player supports analog copy
protection technology. Therefore the
picture may not be displayed properly if
connected to a TV via a DVD recorder/video
deck or when playing the player’s output
material that is recorded by a DVD
recorder/video deck. Furthermore, the
picture may not be displayed properly due
to the copy protection when the player is
connected to a TV with a built-in video
deck. For details, contact the manufacturer
of your TV.
When connecting to a 7.1-channel
compatible audio component – Connect
using the included audio cable and 3
commercially available audio cables (diagram
below).
When connecting to a 5.1-channel
compatible audio component – Connect
using the included audio cable and 2
commercially available audio cables (do not
connect to the surround back left and right
terminals).
• After connecting, set Audio Output
Mode to Multi-channel (page 110).
Connecting the other audio
component
Connect to the other audio component in order
to enjoy the surround sound of Dolby TrueHD,
Dolby Digital Plus, Dolby Digital, DTS-HD
Master Audio, DTS-HD High Resolution Audio
or DTS Digital Surround. For instructions on
connecting the TV and speakers to the audio
component, refer to the operating instructions
of audio component.
80
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Player connections
02
Player’s rear panel
FRONT
SURROUND SURROUND BACK CENTER
L
R
L
VIDEO OUT
VIDEO
Y
AC IN
R
AUDIO OUT
(
2
ch
)
AUDIO OUT
(
7.1 ch
)
SUB WOOFER
P
P
B
HDMI OUT
R
OPTICAL
CONTROL DIGITAL
IN OUT
COMPONENT
VIDEO
S-VIDEO
FRONT
SURROUND SURROUND BACK CENTER
VIDEO OUT
VIDEO
L
Y
R
PB
MI OUT
SUB WOOFER
AUDIO OUT ( 7.1 ch )
PR
COMPONENT
VIDEO
S-VIDEO
OPTICAL
CONTROL DIGITAL
IN OUT
To multi-channel
audio input
To component video input
terminals
terminals
AV receiver or amplifier
Direction of
signal flow
81
En
Download from Www.Somanuals.com. All Manuals Search And Download.
02
Player connections
Connecting the power cord
Connect the power cord after all the connections between devices have been completed.
Player’s rear panel
FRONT
SURROUND SURROUND BACK CENTER
L
R
L
VIDEO OUT
VIDEO
Y
AC IN
R
AUDIO OUT
(
2
ch
)
AUDIO OUT
(
7.1 ch
)
SUB WOOFER
PB
HDMI OUT
PR
OPTICAL
CONTROL DIGITAL
IN OUT
COMPONENT
VIDEO
S-VIDEO
VIDEO OUT
VIDEO
AACC IINN
Y
PB
PR
COMPONENT
VIDEO
S-VIDEO
Power cable (included)
To wall outlet
82
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
03
Chapter 3
Getting Started
If the Setup Navigator menu is not
displayed
Important
• Set the remote control operation selector
switch to BD to operate the Blu-ray disc
player.
•
Press HOME MENU to display the Home
Menu, select Initial Setup Setup
Navigator Start, then press ENTER
.
ENTER
RECEIVER
BD
iPod
3
Select the OSD language.
Use / to select, then press ENTER.
Setup Navigator
BD PLAYER
Please select the on-screen display language.
Making settings using the
Setup Navigator menu
Be sure to perform these settings when using
the player for the first time.
Caution
Audio, subtitle and BDMV/DVD-Video menu
language will also be set.
• Before turning on the power, check that
the connections between the player and
other devices are correct.
When you have this player connected to a
Pioneer Flat Screen TV that is compatible with
HDMI Control, language settings are imported
from the Pioneer Flat Screen TV’s language
settings before Setup Navigator begins.
BD
1
2
Turn on the power.
Turn on the TV’s power and switch the
input.
ENTER
See the TV’s operating instructions for
instructions on operating the TV.
4
Select and set the video and audio
output terminals.
Select the actually connected video and audio
output terminals.
Check that the Setup Navigator menu is
displayed.
Use /// to select, then press ENTER.
If TV Control is set, the TV can be operated with
the receiver’s remote control (page 86).
Setup Navigator
BD PLAYER
Select the output terminals to be used for
the video and audio signals of this player.
Video
HDMI
Audio
HDMI
Use [
press [
][
][
] to select video or audio, then
] to select the output terminal.
83
En
Download from Www.Somanuals.com. All Manuals Search And Download.
03
Getting Started
• When HDMI is selected for Video or
Audio, proceed to step 5.
ENTER
5
Select and set the HDMI High-
• When Component Video is selected for
Video, proceed to step 6.
Speed Transmission setting.
Use / to select, then press ENTER.
• When S-Video/Video is selected for
Video, proceed to step 7.
Setup Navigator
BD PLAYER
Setting item
Output terminal name
Select the HDMI Hi-speed transmission setting.
HDMI
HDMI Output
Off
On
Component
Video
Video Output Component
Video
Normally select [On] (Recommended).
Select [Off] if the video or audio of HDMI-connected
was not output in the test output.
S-Video/Video
S-Video
Video
HDMI
HDMI Output
• When HDMI High-Speed Transmission is
set to On, use the supplied HDMI cable or
a High Speed HDMI™ cable. The picture
and sound may not be output properly if
any other HDMI cable (standard HDMI™
cable) is used.
Digital Audio Digital Audio Optical
Output
Analog Audio Audio Output (2 ch)
Audio Output (7.1 ch)
• When HDMI is selected for Video, proceed
to step 8.
Caution
• When Component Video is selected for
Video, proceed to step 6.
• When HDMI is selected for Video, no video
signals are output from the COMPONENT
VIDEO, S-VIDEO or VIDEO output
terminals.
• When S-Video/Video is selected for
Video, proceed to step 7.
• When Component Video or S-Video/
Video is selected for Video, no video
signals are output from the HDMI OUT
terminal.
ENTER
6
Select the output video resolution
from the COMPONENT VIDEO output
terminals.
Use / to select, then press ENTER.
• The video and audio signals output from
the set output terminals are output
synchronously (lip synchronization).
Setup Navigator
BD PLAYER
• Linear PCM audio signals (2 channels) are
output from all terminals other than the
ones selected for Audio, regardless of the
audio format or the player’s settings.
Select the output video resolution at the
Component video terminal.
If you select [Source Direct], the output
resolution is determined according to the
video format of the playing source.
For details on the resolution settings, see
Switching the output video resolution on
page 87.
84
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
03
ENTER
ENTER
7
Select the aspect ratio of your TV.
10
Finish the Setup Navigator menu.
Use / to select, then press ENTER.
Use / to select Finish, then press ENTER.
Setup Navigator
BD PLAYER
Setup Navigator
BD PLAYER
Select the screen aspect ratio to match
your TV.
Setup is complete!
Finish
Go Back
The setup menu comes back in 30 seconds.
To redo the settings from the start, select Go
Back.
ENTER
8
Check the settings.
Select Proceed, then press ENTER.
Depending on the output terminal setting of
step 4 or the HDMI cable being used, it may
happen that no picture and/or sound is output.
If this happens, the setup returns to step 4 if
there is no operation for over 30 seconds. Once
the setup returns to step 4, redo the settings
according to the connected devices and the
HDMI cable being used.
Setup Navigator
BD PLAYER
Select [Proceed] if you want to start testing
your audio and video settings.
Proceed
About the screen saver
The screen saver is automatically activated if
there is no operation for over 1 minute after
playback is stopped or paused. The screen
saver turns off when an operation is performed
on the player or remote control.
ENTER
9
Output test tones.
Use / to select Yes, then press ENTER.
Setup Navigator
BD PLAYER
The screen saver is automatically activated if
there is no operation for over 1 minute after the
Home Menu or Home Media Gallery is
displayed while playing a BD or DVD.
The test tone will be output.
Reduce the volume to an appropriate level.
Yes
No
With CDs and music files, the screen saver is
automatically activated if no button is operated
for over 1 minute, even while the CD or music
file is playing.
The video and/or audio may not be output under certain setup.
The setup menu comes back in 30 seconds.
Caution
• The screen in step 10 and test tones are
output simultaneously according to the
settings in steps 4 to 7. Lower the volume of
the devices connected with the player.
85
En
Download from Www.Somanuals.com. All Manuals Search And Download.
03
Getting Started
TOOLS menu item list
Item Description
Output Video Switch the output video resolution
Using the TOOLS menu
Various functions can be called out according
to the player’s operating status.
Resolution
from the various output terminals
(page 87).
SETUP
Play from
Beginning
Play the selected title, track or file
from the start.
1
TOOLS
Display the TOOLS menu.
Play Mode
Display the Play Mode screen
(page 95).
Angle
Switch the BD-ROM/DVD-Video
disc’s camera angles (page 92).
Subtitle
Audio
Switch the subtitles (page 93).
BD PLAYER
TOOLS
Video Adjust
Audio DRC
Add to HMG Playlist
Audio
Switch the audio streams/channels
(page 93).
Subtitle
Secondary
Audio
Switch the BD-ROM’s secondary
audio streams/channels (page 93).
ENTER
Secondary
Video
Switch the BD-ROM’s secondary
video (Picture-in-Picture) (page 94).
2
Select and set the item.
Use / to select, then press ENTER.
Original/Play Switch the DVD-R/-RW’s (VR format)
List
list screen between the original list
and the playlist.
Note
Add to HMG Add the selected track or file to the
Playlist HMG Playlist (page 103).
• Items that cannot be changed are
displayed in gray. The items that can be
selected depend on the player’s status.
Delete from Delete the selected track or file from
HMG Playlist the HMG Playlist (page 104).
Now Playing Display the playback screen of the
currently playing track or file.
To close the TOOLS menu
•
Press TOOLS or RETURN.
Video Adjust Display the picture quality
adjustment screen (page 105).
Audio DRC
BDMV Data Erase the additional data from BD-
Erase ROMs.
Adjust the Audio DRC (page 107).
86
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
03
Caution
Erasing the additional data
from BD-ROMs
• It takes time to erase the BDMV data for a
while. Do not unplug the power cord for
about 10 seconds after performing the
above procedure.
When a BD-ROM is played, additional data
may be stored in the player’s memory (local
storage).
If the message indicating low memory (local
storage) appears, erase the BDMV data.
Switching the video output
terminal
Caution
Use the procedure below to switch the video
output terminal. Switch between the digital
output (HDMI OUT terminal) and the analog
output (COMPONENT VIDEO, S-VIDEO or
VIDEO output terminals).
• When the BDMV data is erased, all the data
of secondary video (Picture-in-Picture),
secondary audio, bookmark, etc. that has
been stored is erased.
SOUND
SETUP
VIDEO
SELECT
•
Switch the terminal from which the
1
Display the Tools menu.
TOOLS
video signals are output.
The video output terminal switches each time
the button is pressed.
With no disc loaded, press the TOOLS button.
BD PLAYER
TOOLS
Output Video Resolution
BDMV Data Erase
Caution
• The picture may not be displayed for a
while when the video output terminal is
switched.
ENTER
2
Select and set the item.
Use / to select BDMV Data Erase, then
press ENTER.
• When the HDMI OUT terminal is selected,
no video signals are output from the other
video output terminals.
• When a video output terminal other than
the HDMI OUT terminal is selected, no
video signals are output from the HDMI
OUT terminal. However, audio signals are
output.
ENTER
3
Erase the data.
Use / to select Yes, then press ENTER.
Erases all of the data
added from BDMV.
Please wait a while.
Switching the output video
resolution
OK to erase data?
Yes
No
Use the procedure below to switch the output
video resolution from the various video output
terminals.
87
En
Download from Www.Somanuals.com. All Manuals Search And Download.
03
Getting Started
T.EDIT
The output video resolution can also be
switched using /.
OUTPUT
RESOLUTION
•
Press OUTPUT RESOLUTION.
The output video resolution can be switched by
selecting Output Video Resolution from the
TOOLS menu.
The current output video resolution is
displayed on the TV screen and on the player’s
front panel display.
The output video resolution depends on the
video output terminal. See the table below.
When pressed again, the output video
resolution switches.
The table below shows the output video
resolution for the different terminals when the
frame/field frequency of the playback source is
50 Hz on the upper line, the resolutions when
the source's frame/field frequency is 60 Hz on
the lower line.
Video resolution of the
currently playing disc
Example:
Auto
Output Video Resolution
Source : 1080/50i
Current Output : 1080/50i
Output video resolution
from the player
Output video
resolution setting terminal
HDMI OUT
COMPONENTVIDEO S-VIDEO/VIDEO
TV system
1
output terminals1
output terminal
2
Resolution preferred
—
—
PAL
5
Auto
3,4
by TV
576i or 480i
576/50i
480/60i
576/50i
480/60i
576/50i
480/60i
PAL
5
576p or 480p
1080i
576/50p
480/60p
576/50p
480/60p
576/50i
480/60i
PAL
5
1080/50i
1080/60i
576/50p
576/50i
480/60i
PAL
6
5
1080/60i
2
7
7
—
—
PAL
1080p
1080/50p
1080/60p
5
Source Direct
Resolution recorded Resolution recorded 576/50i
PAL
3,8,9
8,9,10
on disc
on disc
5
480/60i
1. Depending on the BD, the pictures may not be output.
2. Cannot be selected when the video signals are being output from the COMPONENT VIDEO output terminals,
S-VIDEO output terminal or the VIDEO output terminal.
3. For details on the output of film material (1080/24p or 720/24p video signals), see To output film material
.
4. Sources with a resolution of 720/50p, 720/60p and 720/24p are output at 1080/50i or 1080/60i, even if the TV’s pre-
ferred resolution is 1080/50p or 1080/60p.
5. Depends on the NTSC on PAL TV setting (page 109).
6. DVD-Video or DVD VR format is output at 480/60p. BDs format may be output at 480/60p.
7. Depending on the connected HDMI cable, the video signals may not be output. Also, sources with a resolution
of 720/50p is output at 1080/50i, and 720/60p and 720/24p are output at 1080/60i.
8. Depending on the connected TV, the video signals may not be output.
9. 720/24p film material is output at 720/60p.
10.1080/24p film material is output at 1080/60i.
88
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
03
Eject the disc, then press the OPEN/CLOSE
button on the front panel while pressing the
PLAY button to switch to a different frame/
field frequency. The frame/field frequency
switches between 50 Hz and 60 Hz each time
this operation is performed. The indicator for
the frame frequency’s current setting lights on
the front panel display (page 14).
Caution
• On some TVs, the picture may not be
displayed properly when the resolution is
switched. If this happens, use OUTPUT
RESOLUTION to set to a resolution at
which the picture is properly displayed.
• When video signals are being output with a
resolution of 1080/50i, 1080/50p, 720/50p,
1080/24p, 1080/60i, 1080/60p or 720/60p
from the HDMI OUT terminal or
COMPONENT VIDEO output terminals,
the picture may be output with an aspect
ratio of 16:9, even if the TV Aspect Ratio is
set to 4:3 (Standard).
About Film material
The film material is a video signal with a frame
rate of 24 frames/second. For example, these
materials include 1080/24p, 720/24p, etc.
Video resolution of the
currently playing disc
Example:
• The picture may not be displayed for a
while when the resolution is switched.
ꢀ
Auto
ꢁ
Output Video Resolution
Source : 1080/24p
Current Output : 1080/24p
Output video resolution
from the player
About the frame/field frequency and
NTSC/PAL TV systems
By factory default setting, the frame/field
frequency is set for an output of 50 Hz, and the
video signal output from the S-VIDEO and
VIDEO output terminals is set to be output in
the PAL TV system format. When sources with
a frame/field frequency of 60 Hz or 24 Hz are
played, the output frame/field frequency
automatically switches to 60 Hz (or 24 Hz for
HDMI, depending on the setting), and the TV
system format for the video signal output from
the S-VIDEO and VIDEO output terminals is
set to NTSC on PAL TV. When playback is
stopped, the frame/field frequency and TV
system settings remain at the settings last
used. The frame/field frequency and TV system
settings do not change even when the power is
turned off. They only switch when a video
material with a different frame/field frequency
is played.
To output film material
To output 1080/24p film material from the
HDMI OUT terminal, set the output video
resolution to either Auto or Source Direct.
Caution
• 1080/24p signals can only be output from
the HDMI OUT terminal. They cannot be
output from other video terminals.
• When Auto is selected, the picture is
output at 60 frames/second if your TV is not
compatible with 1080/24p signals.
• When Source Direct is selected, the
signals are output as such, even if your TV
is not compatible with 1080/24p signals. If
the picture is not displayed properly, use
OUTPUT RESOLUTION to set to the output
video resolution at which the picture is
properly displayed.
If the picture is not displayed on the TV when a
source with a different frame/field frequency is
played, use the procedure below to switch the
frame/field frequency and TV system settings
for the signal output from the player.
• 720/24p video signals are output at 60
frames/second, even if the resolution is set
to Auto or Source Direct.
89
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
CPhlaapteyr b4 ack
3
Press
(play) to play the disc.
Important
To pause, press (pause) during playback.
• Set the remote control operation selector
switch to BD to operate the Blu-ray disc
player.
To stop, press (stop) during playback.
Note
• Some discs start playing automatically
when the disc tray is closed.
RECEIVER
BD
iPod
• DVD-Video discs have parental lock
features. Input the password registered in
the player’s settings to unlock the parental
lock. For details, see page 117.
Playing discs or files
This section describes the player’s main
operations.
• For some BD-R/-RE, playback protection is
set for the disc or titles. Input the code
number set for the disc to unlock the
protection.
For the types of discs that can be played, see
Playable discs on page 71. For the types of files
that can be played, see Playable files on
page 74. Movie and music files recorded on
discs are played with Home Media Gallery
(page 100).
If the disc menu is displayed
For some discs, the disc menu is displayed
automatically when playback starts. The
contents of the disc menu and the way to
operate differ from disc to disc.
BD
1
Press BD to turn on the power.
Turn the TV’s power on and switch its input
beforehand.
Resuming playback from where it was
stopped (resume playback function)
• When (stop) is pressed during playback,
the point at which the disc stopped is
2
Press OPEN/CLOSE on the
front panel to open the disc tray and load the
disc.
stored in the memory. When (play) is
pressed, playback resumes from that point.
• For CDs and music files, playback starts
from the beginning of the track/file that
was playing.
Note
• Load the disc with the printed
side facing up.
• To cancel the resume playback function,
press (stop) while playback is stopped.
• Several dozen seconds are
required to read the disc. Once
reading is completed, the type of
disc is displayed on the player’s
front panel display.
90
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
04
Playing specific titles, chapters or
tracks
Note
• The resume playback function is canceled
automatically in the following cases:
BD
Movie files
Music files
DVD
AVCHD
CD
– When the disc tray is opened.
– When the file list window is switched.
– When the power is turned off. (For BDs
and DVDs this does not cancel the
resume playback function.)
1
4
2
3
6
9
5
8
0
7
ENTER
CLEAR
•
Input the number of the
• The resume playback function cannot be
used for some discs.
title, chapter or track you want to play.
• Use the number buttons (0 to 9) to input
the number, then press ENTER.
Forward and reverse scanning
BD
Movie files
Music files
Note
DVD
AVCHD
CD
• For some discs, it is not possible to specify
and play titles, chapters or tracks.
• Press CLEAR to clear the values you have
input.
/
/
1
During playback, press
or
.
Skipping content
• The scanning speed switches each time
the button is pressed. The speed steps
depend on the disc or file (the speed is
displayed on the TV screen).
BD
Movie files
Music files
DVD
AVCHD
CD
• Forward or reverse scanning is also
possible by holding the button down.
Normal playback resumes when the button
is released.
•
Press
or
.
• When is pressed, the disc skips ahead
to the beginning of the next title/chapter/
track/file.
Note
• When is pressed, the disc skips back
to the beginning of the currently playing
title/chapter/track/file. Press twice to skip
back to the beginning of the previous title/
chapter/track/file.
• No sound is output when scanning BDs,
DVDs and movie files.
• Sound is output when scanning CDs and
music files.
• For some discs, normal playback resumes
automatically when the chapter switches.
Note
• There are some discs for which skipping is
not possible.
To resume normal playback
•
Press
(play).
91
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
Playing in slow motion
Note
BD
Movie files
• For some discs, normal playback resumes
automatically when the chapter switches.
DVD
AVCHD
CD
Music files
• Reverse step playback is not possible with
movie files.
/
/
• There are some discs for which step
forward/reverse playback is not possible.
•
While playback is paused,
or
press and hold
/
/.
• The speed switches each time the button is
pressed (the speed is displayed on the TV
screen). The speed steps depend on the
disc or file.
To resume normal playback
•
Press
(play).
Switching the camera angles
For BD-ROM and DVD-Video discs on which
multiple angles are recorded, the angles can
be switched during playback.
Note
• It is not possible to switch the speed during
reverse slow motion playback.
• No sound is output during slow motion
playback.
BD
Movie files
Music files
DVD
AVCHD
CD
• For some discs, normal playback resumes
automatically when the chapter switches.
• Reverse slow motion playback is not
possible with movie files.
•
ANGLE
During playback, press ANGLE.
• The current angle and total number of
recorded angles are displayed on the TV
screen and on the player’s front panel
display. When pressed again, the angle
switches.
• There are some discs for which slow
motion playback is not possible.
To resume normal playback
•
Press
(play).
Current angle/Total number of
recorded angles
Example:
Step forward and step reverse
ꢀ
1/4
ꢁ
Angle
BD
Movie files
DVD
AVCHD
CD
Music files
• The angles can also be switched using /
.
• The angles can also be switched by
selecting Angle from the TOOLS menu.
/
/
•
While playback is paused,
press
/
or
/.
• Angle mark
is displayed for scenes at
• The disc moves a step forward or reverse
each time the button is pressed.
which multiple angles are recorded.
92
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
04
• If the subtitles are not switched when
SUBTITLE is pressed, switch them from the
menu screen.
Note
• For some discs, the angle can also be
switched on the menu screen.
• This player does not support the display of
external subtitle files for DivX.
• Angle mark
is not displayed if Angle/
Secondary Indicator is set to Off
(page 113).
Turning the subtitles off
•
Press SUBTITLE, then press CLEAR.
Switching the subtitles
For discs or files on which multiple subtitles
are recorded, the subtitles can be switched
during playback.
Switching the audio streams/
channels
For discs or files on which multiple audio
streams/channels are recorded, audio
streams/channels can be switched during
playback.
BD
Movie files
DVD
AVCHD
CD
Music files
BD
Movie files
DVD
AVCHD
CD
Music files
•
During playback, press SUBTITLE.
• The current subtitle and total number of
SUBTITLE
recorded subtitles are displayed on the TV
screen and on the player’s front panel
display. When pressed again, the subtitle
switches.
CTRL
AUDIO
•
During playback, press AUDIO.
• The current audio stream/channel and
total number of recorded audio streams/
channels are displayed on the TV screen
and on the player’s front panel display.
When pressed again, the audio stream/
channel switches.
Current subtitle/Total number of
recorded subtitles
Example:
1/2 English
Subtitle
Current audio stream/Total number
of recorded audio streams
Example:
• The subtitles can also be switched using
/.
• The subtitles can also be switched by
selecting Subtitle from the TOOLS menu.
Audio
Dolby True HD
2/2 English
96kHz 7.1ch L C R Ls Rs Lb Rb LFE
Number of
channels
Channels recorded
on disc
Audio type
Note
• The audio streams/channels can also be
switched using /.
• The audio streams/channels can also be
switched by selecting Audio from the
TOOLS menu.
• In some cases the subtitle may switch or
the switching screen provided on the disc
may be displayed immediately, without the
current subtitle or the total number of
subtitles recorded on the disc being
displayed.
• The types of recorded subtitles depend on
the disc and file.
93
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
Note
3
Use
/
to select secondary
is displayed for
• The types of recorded audio streams/
channels depend on the disc and file.
audio.
• Secondary audio mark
scenes at which secondary audio is
recorded.
• If the audio stream/channel is not switched
when AUDIO is pressed, switch it from the
menu screen.
Example:
Currentsecondaryaudiostream/Total
number of recorded secondary audio
streams
Switching the secondary audio
Use the procedure below switch the secondary
audio recorded on the BD-ROM.
Secondary Audio
2/2 English
y
g
Dolb Di ital Plus 48kHz 5.1ch L C R Ls Rs LFE
BD
Movie files
Music files
DVD
AVCHD
CD
Audio type
Number of
channels
Channels recorded
on disc
SETUP
Note
• In some cases the secondary audio may
switch or the switching screen provided on
the disc may be displayed immediately,
without the current secondary audio or the
total number of secondary audio streams
recorded on the disc being displayed.
1
Display the TOOLS menu.
TOOLS
During playback, press TOOLS.
ENTER
2
Select and set the item.
Use / to select Secondary Audio, then
press ENTER.
• The types of recorded audio streams/
channels depend on the disc and file.
• The current secondary audio stream/
channel and total number of recorded
secondary audio streams/channels are
displayed on the TV screen and on the
player’s front panel display.
• Some BD-ROMs do not include secondary
audio.
• Secondary audio mark
is not
displayed if Angle/Secondary Indicator is
set to Off (page 113).
Switching the secondary video
Use the procedure below to switch the
secondary video (Picture-in-Picture) recorded
on the BD-ROM.
BD
Movie files
Music files
DVD
AVCHD
CD
SETUP
1
Display the TOOLS menu.
TOOLS
During playback, press TOOLS.
94
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
04
DISPLAY
ENTER
•
Press DISPLAY.
2
Select and set the item.
The disc information appears on the TV screen.
The information switches each time the button
is pressed.
Use / to select Secondary Video, then
press ENTER.
• The current secondary video stream and
total number of recorded secondary video
streams are displayed on the TV screen and
on the player’s front panel display.
The information display differs during playback
and when playback is stopped.
Using the Play Mode functions
Playing from a specific time (Time
Search)
3
Use
/
to select secondary
video.
Current secondary video stream/Total
number of recorded secondary video
streams
Example:
SETUP
1
Display the TOOLS menu.
TOOLS
During playback, press TOOLS.
ꢀ
1/4
ꢁ
Secondary Video
ENTER
• Secondary video mark
scenes at which secondary video is
recorded.
is displayed for
2
Select and set the item.
Use / to select Play Mode, then press
ENTER.
Note
ENTER
3
Select Time Search.
• In some cases the secondary video may
switch or the switching screen provided on
the disc may be displayed immediately,
without the current secondary video or the
total number of secondary video streams
recorded on the disc being displayed.
Use / to select, then press ENTER.
Play Mode
Time Search
Title Search
Chapter Search
A-B Repeat
Repeat/Random
• Some BD-ROMs do not include secondary
video.
• Secondary video mark
displayed if Angle/Secondary Indicator is
set to Off (page 113).
is not
1
4
2
5
8
0
3
6
9
ENTER
7
CLEAR
4
Input the time.
Use the number buttons (0 to 9) or / to
Displaying the disc information
input the time.
BD
Movie files
Use / to move the cursor.
DVD
AVCHD
CD
Music files
Time Search
1
2
:
4
5
:
0
0
Search
95
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
1
4
2
5
8
0
3
6
9
Note
ENTER
7
• To play from 45 minutes, input 0, 0, 4, 5, 0
and 0, then press ENTER.
CLEAR
4
Input the number.
Use the number buttons (0 to 9) or / to
input the number.
• To play from 1 hour 20 minutes, input 0, 1,
2, 0, 0 and 0, then press ENTER.
Use / to move the cursor.
• Press CLEAR to clear the values you have
input.
Title
Title Search
0
3
2
Search
ENTER
5
Starting playback from the
specified time.
Use / to select Search, then press ENTER.
ENTER
5
Starting playback from the
specified title, chapter or track.
Use / to select Search, then press ENTER.
To cancel Time Search
•
Press RETURN.
To cancel the search
Note
•
Press RETURN.
• There are some discs for which Time
Search is not available.
Note
Playing a specific title, chapter or
track (Search)
• To search for title 32, input 0, 3 and 2, then
press ENTER.
• There are some discs for which searching
is not available.
SETUP
• Press CLEAR to clear the values you have
1
Display the TOOLS menu.
TOOLS
input.
ENTER
Playing a specific section within a
2
Select and set the item.
title or track repeatedly (A-B Repeat)
Use this procedure to play a specific section
within a title or track repeatedly.
Use
ENTER
/
.
to select Play Mode, then press
ENTER
SETUP
3
Select the type of search.
1
Display the TOOLS menu.
TOOLS
Use / to select, then press ENTER.
See the table on page 99 for the search types.
During playback, press TOOLS.
Play Mode
ENTER
2
Select and set the item.
Time Search
Title Search
Chapter Search
A-B Repeat
Use / to select Play Mode, then press
ENTER.
Repeat/Random
96
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
04
Playing repeatedly (Repeat Play)
Use this procedure to play the currently playing
disc, title, chapter, track or file repeatedly.
ENTER
3
Select A-B Repeat.
Use / to select, then press ENTER.
SETUP
Play Mode
1
Display the TOOLS menu.
TOOLS
Time Search
Title Search
Chapter Search
A-B Repeat
During playback, press TOOLS.
Repeat/Random
ENTER
2
Select and set the item.
Use / to select Play Mode, then press
ENTER.
ENTER
4
Select the starting point for A-B
Repeat.
ENTER
Use / to select A (Start), then press
ENTER.
3
Select Repeat/Random.
Use / to select, then press ENTER.
Play Mode
A-B Repeat
A (Start)
B (End)
Off
Time Search
Title Search
Chapter Search
A-B Repeat
Repeat/Random
ENTER
5
Select the end point for A-B
Repeat.
ENTER
Use / to select B (End), then press ENTER.
4
Select the type of Repeat Play.
Use / to select, then press ENTER.
A-B Repeat playback starts.
See the table on page 99 for the types of repeat
playback.
To cancel A-B Repeat play
• Select Off from the Repeat/Random
screen, then press ENTER.
Repeat/Random
Off
• During playback, press (stop) or CLEAR.
Repeat All
Repeat Track
Random Track
Note
• A-B Repeat play is canceled in the
following cases:
To cancel Repeat Play
• Select Off from the Repeat/Random
screen, then press ENTER.
– When the angle is switched (for BD-
ROM and DVD-Video discs only).
– When you search outside the repeat
range.
• During playback, press (stop) or CLEAR.
– When you start other repeat or random
play.
97
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
Note
ENTER
4
Select the Random Play.
• There are some discs and files for which
Repeat Play is not available.
Use / to select, then press ENTER.
• The type of repeat modes depends on the
disc and file being played. See the table on
page 99.
Repeat/Random
Off
Repeat All
Repeat Track
Random Track
• Repeat Play is canceled in the following
cases:
– When the angle is switched (for BD-
ROM and DVD-Video discs only).
To cancel Random Play
• Select Off from the Repeat/Random
screen, then press ENTER.
– When you search outside the repeat
range.
– When you start other repeat or random
play.
• During playback, press (stop) or CLEAR.
Note
Playing in random order (Random
Play)
• There are some discs and files for which
Random Play is not available.
Use this procedure to play the tracks or files in
random order.
• Random Play is canceled in the following
cases:
SETUP
– When you use the search function.
– When you start repeat play.
1
Display the TOOLS menu.
TOOLS
During playback, press TOOLS.
ENTER
2
Select and set the item.
Use / to select Play Mode, then press
ENTER.
ENTER
3
Select Repeat/Random.
Use / to select, then press ENTER.
Play Mode
Time Search
Title Search
Chapter Search
A-B Repeat
Repeat/Random
98
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
04
About Play Mode types
The functions that can be used differ according to the type of disc and file. In some cases, some
of the functions cannot be used. Check the usable functions on the table below.
Disc/file type
Play Mode type
Playing a specific section within a
title or track repeatedly (A-B
Repeat)
Playing a title repeatedly (Title
Repeat)
Playing a chapter repeatedly
(Chapter Repeat)
Playing a track or file repeatedly
(Track Repeat)
Playing all the titles, tracks or files
on the disc repeatedly (All Repeat)
3
4
5
6
Playing the tracks or files in
random order (Random Track)
Playing from a specific time (Time
Search)
—
—
—
—
Playing a specific title (Title
Search)
Playing a specific chapter
(Chapter Search)
Playing a specific track (Track
Search)
1.During playback in a Play Mode, the type of Play Mode is indicated by the mark.
2.For BD-ROM and DVD-Video discs, some of the functions cannot be used with some titles.
3.The original titles are played repeatedly. However, the playlist titles cannot be played repeatedly.
4.The files in the folder are played repeatedly.
5.The files in the folder or HMG Playlist are played repeatedly.
6.The tracks in the disc or HMG Playlist are played repeatedly.
99
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
ENTER
Playing from the Home Media
Gallery
3
Select the title or track to be
played.
The Home Media Gallery lets you display a list
of the titles, tracks or files recorded on the disc.
The discs that can be played from the Home
Media Gallery are as shown below (see also
page 71).
Use / to select, then press ENTER.
BD-R BDAV
My Favorite TV Program
1
Morning serial drama
News at noon
2
3
Evening movie
4
Midnight variety show
Playback protection
World heritage
Drama: Blank time
Music and us
• BD-R/-RE discs
5
6
• DVDs recorded in VR format
• Music CDs (CD-DAs and DTS-CDs)
7
8
10 items
Title Total : 0 h 54 m 30 s
11/11/2008
Recording Date :
Original
• DVDs/CDs on which only data files of
movie or music files, etc. are recorded
Playback starts.
Playing discs
Closing the Home Media Gallery
Press HOME MEDIA GALLERY (or HOME
CLASS
•
HOME MEDIA
1
GALLERY
Press HOME MEDIA GALLERY to
MENU).
display the Home Media Gallery
.
The Home Media Gallery can also be displayed
by selecting Home Media Gallery from Home
Menu then pressing ENTER.
Note
• When playing a music CD (CD-DA or DTS-
CD), the Now Playing screen is displayed.
• Some BD-R/-RE discs have playback
protection. To cancel the protection, input
the password set for the disc.
ENTER
2
Select the disc.
Use / to select, then press ENTER.
• To play DVD-R/-RW (VR format) playlists,
switch to the playlist using the Original/
Play List command on the TOOLS menu
(page 86).
Home Media Gallery
BD PLAYER
BD-R BDAV
HMG Playlist
Playing movie files
CLASS
Search for the part you want to play from a list of the disc's content.
HOME MEDIA
1
GALLERY
Press HOME MEDIA GALLERY to
display the Home Media Gallery.
The Home Media Gallery can also be displayed
by selecting Home Media Gallery from Home
Menu then pressing ENTER.
100
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
04
If you have selected All Movies, proceed to
step 6.
ENTER
2
Select the disc.
Use / to select, then press ENTER.
ENTER
5
Select the folder containing the
Home Media Gallery
BD PLAYER
file you want to play.
DVD-RW
HMG Playlist
Use / to select, then press ENTER.
Folders
DVD-RW/Movies
Movie Folder001
Movie Folder002
Movie Folder003
Movie Folder004
Movie005.divx
Movie006.divx
Movie007.divx
Movie008.divx
Search for the part you want to play from a list of the disc's content.
ENTER
15 items
3
Select Movies.
Use / to select Movies, then press ENTER.
A list of the files and/or the sub-folders in the
selected folder is displayed.
DVD-RW
Movies
Music
ENTER
6
Select and set the file you want to
play.
Use / to select, then press ENTER.
View available movies.
Movie Folder001
DVD-RW/Movies/Folders
Movie001.divx
Movie002.divx
Movie003.divx
Movie004.divx
Movie005.divx
Movie006.divx
Movie007.divx
Movie008.divx
ENTER
4
Select Folders or All Movies
.
Use / to select, then press ENTER.
• Folders– The files in the selected folder are
20 items
displayed.
Playback starts.
• All Movies – All the recorded files are
displayed.
Note
Movies
DVD-RW
• It may take a few seconds before playback
starts. This is normal.
Folders
All Movies
• It may not be possible to play some files
properly.
• The number of views may be restricted
(page 75).
101
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
• All Songs – All the recorded files are
displayed.
Playing music files
CLASS
Music
CD-ROM
HOME MEDIA
1
GALLERY
Press HOME MEDIA GALLERY to
Folders
All Songs
display the Home Media Gallery.
The Home Media Gallery can also be displayed
by selecting Home Media Gallery from Home
Menu then pressing ENTER.
ENTER
2
Select the disc.
Use / to select, then press ENTER.
If you have selected All Songs, proceed to step
6.
Home Media Gallery
BD PLAYER
CD-ROM
HMG Playlist
ENTER
5
Select the folder containing the
file you want to play.
Use / to select, then press ENTER.
Search for the part you want to play from a list of the disc's content.
Folders
CD-ROM/Music
Music Folder001
Music Folder002
Music Folder003
Music Folder004
Music005.mp3
Music006.mp3
Music007.mp3
Music008.mp3
ENTER
3
Select Music.
Use / to select Music, then press ENTER.
CD-ROM
15 items
Movies
Music
A list of the files and/or the sub-folders in the
selected folder is displayed.
ENTER
View available music.
6
Select and set the file you want to
play.
Use / to select, then press ENTER.
ENTER
Music Folder001
CD-ROM/Music/Folders
4
Select Folders or All Songs
.
Use / to select, then press ENTER.
• Folders – The files in the selected folder are
Music001.mp3
Music002.mp3
Music003.mp3
Music004.mp3
Music005.mp3
Music006.mp3
Music007.mp3
Music008.mp3
displayed.
20 items
102
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
04
Playback starts. The Now Playing screen
(shown below) is displayed.
Use / to select, then press ENTER.
Home Media Gallery
BD PLAYER
Currently playing
file
Elapsed time
CD-ROM
HMG Playlist
Music 001.mp3
Play 0.02.33
0.05.34
DATA DISC
Total file playing
time
Search for the part you want to play from a list of the disc's content.
3
Select the track/file to be added.
Use / to select.
Playing in the desired order (HMG
Playlist)
Folders
CD-ROM/Music
The discs that can add tracks and files to the
HMG (Home Media Gallery) Playlist are as
shown below.
Music001.mp3
Music002.mp3
Music003.mp3
Music004.mp3
Music005.mp3
Music006.mp3
Music007.mp3
Music008.mp3
• Music CDs (CD-DAs and DTS-CDs)
• DVDs/CDs on which music files are
recorded
15 items
Adding tracks/files
SETUP
Use this procedure to add tracks and files, and
create the HMG Playlist.
4
Press TOOLS to display the TOOLS
TOOLS
menu.
CLASS
HOME MEDIA
1
GALLERY
Press HOME MEDIA GALLERY to
ENTER
display the Home Media Gallery.
5
Select Add to HMG Playlist.
The Home Media Gallery can also be displayed
by selecting Home Media Gallery from Home
Menu pressing ENTER.
Use / to select, then press ENTER.
Folders
CD-ROM/Music
Music001.mp3
Music002.mp3
Music003.mp3
ENTER
Music004.mp3
Music005.mp3
BD PLAYEMRusic006.mp3
TOOLS Music007.mp3
Music008.mp3
2
Select the disc.
Load the disc beforehand.
Play from Beginning
Add to HMG Playlist
Now Playing
15Items
The track or file selected in step 3 is added to
the HMG Playlist.
To add more tracks or files, repeat steps 3 to 5.
103
En
Download from Www.Somanuals.com. All Manuals Search And Download.
04
Playback
To add the currently playing track/file to
the HMG Playlist
ENTER
3
Select the track/file to be played.
SETUP
Use / to select, then press ENTER.
•
While the track/file is playing, press
HMG Playlist
CD-ROM
TOOLS
TOOLS to display the TOOLS menu.
1
2
3
4
5
6
7
8
Track15.mp3
Track07.mp3
Track03.mp3
Track16.mp3
Track08.mp3
Track05.mp3
Track10.mp3
Track03.mp3
ENTER
•
Use
/
to select Add to HMG
Playlist, then press ENTER
.
21 items
Note
Playback starts. The Now Playing screen
(shown below) is displayed.
• A maximum of 24 tracks/files can be added
to the HMG Playlist.
Currently playing
track/file
Elapsed time
• The HMG Playlist is cleared in the following
cases:
Music 001.mp3
Play 0.02.33
0.05.34
HMG
– When the power is turned off.
– When the disc tray is opened.
DATA DISC
Total track/file
playing time
Playing the HMG Playlist
CLASS
HOME MEDIA
1
GALLERY
Press HOME MEDIA GALLERY to
display the Home Media Gallery.
Press (stop) to stop playback. When
playback of a music CD is stopped, the Now
Playing screen turns off. When playback of a
music file is stopped, the HMG Playlist screen
reappears.
The Home Media Gallery can also be displayed
by selecting Home Media Gallery from Home
Menu pressing ENTER.
ENTER
2
Select HMG Playlist.
Deleting tracks/files from the HMG
Playlist
Use / to select, then press ENTER.
Home Media Gallery
BD PLAYER
SETUP
CD-ROM
HMG Playlist
•
Select the track/file to be deleted,
TOOLS
then press TOOLS to display the TOOLS
menu.
ENTER
Display the HMG Playlist.
•
Use
/
to select Delete from
HMG Playlist, then press ENTER
.
104
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting audio and video
05
Chapter 5
Adjusting audio and video
• Projector – Select this when connected to
a front projector.
Important
• Set the remote control operation selector
switch to BD to operate the Blu-ray disc
player.
• Professional – With this setting, video
signal processing is restrained. Select this
when connected to a professional monitor.
• Memory1 to 3 – Picture quality settings
with adjusted parameters can be stored in
the memory. For a description of the
parameters, see When Memory1, 2 or 3 is
selected below.
RECEIVER
BD
iPod
Adjusting the video
When Memory1, 2 or 3 is selected
The quality of the playback picture can be
adjusted according to the TV you are using.
ENTER
SETUP
1
Select Adjustments.
Use to select Adjustments, then press
ENTER.
1
Display the TOOLS menu.
TOOLS
During playback, press TOOLS.
A detailed settings screen appears.
ENTER
2
Select and set the item.
Use / to select Video Adjust, then press
ENTER.
2
Select the item to be adjusted.
Use / to select.
Video Adjust [ Memory1 ]
ENTER
Prog. Motion
Pure Cinema
YNR
Motion
Still
3
Select a preset.
Auto1
Off
Off
Off
Off
Max
Max
Max
Max
Select using / according to the TV being
CNR
used.
BNR
MNR
Video Adjust
1/2 Page
PDP
Adjustments
Use [
][
] to adjust the picture to progressive scan.
• LCD – Select this when connected to a
liquid crystal display TV.
• PDP – Select this when connected to a
plasma TV of another brand.
• Pioneer PDP – Select this when connected
to a Pioneer plasma TV.
105
En
Download from Www.Somanuals.com. All Manuals Search And Download.
05
Adjusting audio and video
• Gamma Correction – Adjusts how the
dark portions of the picture look.
ENTER
3
Adjust the picture quality.
• Hue – Adjusts the balance between green
and red.
When / are pressed, the adjustments can
be made watching the picture. The detailed
settings screen reappears when ENTER is
pressed.
• Chroma Level – Adjusts the density of the
colors.
Prog. Motion
Motion
Still
Note
• Prog.Motion and Pure Cinema have the
effect only for pictures recorded in the
interlaced scan format (576i/480i or 1080i
signals).
• Prog.Motion – Adjust according to the
type of image (movie or still image). This is
effective when outputting video materials
as progressive images.
• Prog.Motion is disabled when Pure
Cinema is set to On.
• Pure Cinema – This setting optimizes the
operation of the progressive scanning
circuit for playing film materials. Normally
set it to Auto1. If the picture seems
unnatural, switch this to Auto 2, On or Off
(page 106).
• Black Setup have the effect only for
pictures output from the VIDEO and S-
VIDEO output terminals, and for NTSC
signals output.
• YNR – Reduces noise in the luminance (Y)
signal.
• YNR, CNR, BNR and MNR are disabled
when 1080/24p signals are output from the
HDMI OUT terminal.
• CNR – Reduces noise in the chroma (C)
signal.
Closing the Video Adjust screen
• BNR – Reduces the block noise (block-
shaped distortion generated upon MPEG
compression).
•
Press HOME MENU
.
• MNR – Reduces the mosquito noise
(distortion along the contours of the
picture generated upon MPEG
compression).
About Pure Cinema
There are two types of video signals:
• Video material – Video signals recorded
at 25 or 30 frames/second
• Detail – Emphasizes the picture’s
contours.
• Film material – Video signals recorded at
24 frames/second
• White Level – Adjusts the level of the
“Pure Cinema” uses signal processing suited
for “film material” when converting 576i/480i or
1080i interlaced video signals into progressive
video signals, resulting in clear picture
reproduction without losing the quality of the
material.
white portions.
• Black Level – Adjusts the level of the black
portions.
• Black Setup – Select the black level as the
setup level. Normally select 0 IRE. If the
black is too dense and all the dark colors
are displayed in a uniform black due to the
combination with the connected monitor,
select 7.5 IRE.
is displayed on the disc information
screen when playing the “film material”
pictures of DVD-Video discs (page 95).
106
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting audio and video
Adjusting the Audio DRC
05
• Audio DRC affects the audio signals output
from the following audio output terminals:
Audio DRC (Dynamic Range Control) has the
effect of playing loud sounds softly and soft
sounds loudly. Adjust the setting for example
when watching movies late at night and the
dialogs are difficult to hear.
– Analog audio signals output from the
AUDIO OUT (2 ch) or AUDIO OUT (7.1
ch) terminals.
– Linear PCM audio signals output from
the DIGITAL OUT terminals or HDMI
OUT terminal.
SETUP
• The effect may be weak for some discs.
1
During playback, display the TOOLS
TOOLS
menu.
ENTER
2
Select and set Audio DRC
.
Use / to select, then press ENTER.
BD PLAYER
TOOLS
Audio
Subtitle
Audio DRC
Video Adjust
Output Video Resolution
3
Adjust the setting.
Use / to switch between Off, Low,
Medium, High and Auto.
Audio DRC
Off
Adjust the audio dynamic range. This setting is
ineffective depending on the playing audio.
Closing the Audio DRC screen
•
Press ENTER or HOME MENU.
Note
• This only affects the Dolby TrueHD, Dolby
Digital Plus and Dolby Digital audio signals
of BDs, DVDs and movie files.
• When Auto is selected, the setting has the
same effect as High or Off for Dolby
TrueHD signals, depending on the content.
For Dolby Digital Plus and Dolby Digital,
the setting has the same effect as Off.
107
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
Chapter 6
Advanced settings
Important
ENTER
2
Select and set Initial Setup.
• Set the remote control operation selector
switch to BD to operate the Blu-ray disc
Use / to select, then press ENTER.
player.
HOME MENU
BD PLAYER
Home Media Gallery
Initial Setup
RECEIVER
BD
iPod
Changing the settings (Initial
Setup)
Set up the player for use.
ENTER
Operating the Initial Setup screen
3
Select the item and change the
HOME
MENU
setting.
Use /// to select, then press ENTER.
1
When playback is stopped, display
the Home Menu screen.
Press HOME MENU.
Closing the Initial Setup screen
•
Press HOME MENU.
Note
• Items that cannot be changed are indicated in gray. The items that can be selected depend on
the player’s status.
• The factory default settings are indicated in bold.
Setting
Options
Explanation
Video Out
TV Aspect Ratio
16:9 (Widescreen) Select this when connected to a wide (16:9) TV.
4:3 (Standard)
Full
Select this when connected to a conventional TV.
4:3 pictures are displayed over the entire screen.
4:3 Video Out
Normal
4:3 pictures are displayed with black bands along the sides.
Select this when you cannot switch the aspect ratio to 4:3 on
the TV.
108
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
06
Setting
Options
Explanation
DVD 16:9 Video Out
NTSC on PAL TV
Letter Box
16:9 pictures are displayed with black bands at the top and
bottom when watching on a 4:3 screen.
Pan & Scan
The picture is displayed over the entire screen, with the left
and right sides of the 16:9 picture cut off. Select this to watch
4:3 pictures over the entire screen.
On
Select this when connected to the PAL-only TV. When playing
the materials with the frame/field rate other than 50 Hz, the
PAL-only TV can display correctly.
Off
Select this when multi-system (NTSC-compatible) TV.
Many recent PAL TVs support the input of NTSC signals. Therefore, this can be set to Off. Check also the
operating instructions of your TV.
Still Picture
Field
This eliminates instability of the picture when playback is
paused.
Frame
Auto
This makes pictures clear when playback is paused, but
instability may be observed.
Field or Frame is selected automatically according to the
disc or file being played.
Audio Out
Dolby Digital Out
Dolby Digital 1
Dolby Digital audio signals are output. With BD-ROMs, the
secondary audio and interactive audio are mixed for output.
* Only valid for digital
audio outputs.
Dolby Digital 2
Dolby Digital audio signals are output. With BD-ROMs, the
signals are output without mixing the secondary audio and
interactive audio signals.
Dolby Digital
PCM
Select this when the connected AV receiver or amplifier, etc.,
is not compatible with Dolby Digital audio signals. The Dolby
Digital audio signals are converted into linear PCM audio
signals for output.
DTS Out
DTS 1
DTS Digital Surround audio signals are output. With BD-
ROMs, the secondary audio and interactive audio are mixed
for output.
* Only valid for digital
audio outputs.
DTS 2
DTS Digital Surround audio signals are output. With BD-
ROMs, the signals are output without mixing the secondary
audio and interactive audio signals.
DTS PCM
Select this when the connected AV receiver or amplifier, etc.,
is not compatible with DTS Digital Surround audio signals.
The DTS Digital Surround audio signals are converted into
linear PCM audio signals for output.
109
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
Setting
Options
Explanation
AAC Out
AAC
Select this when the connected AV receiver or amplifier, etc.,
is compatible with AAC audio signals. The AAC audio signals
are output.
* Only valid for digital
audio outputs.
AAC PCM
Stereo
Select this when the connected AV receiver or amplifier, etc.,
is not compatible with AAC audio signals. The AAC audio
signals are converted into linear PCM audio signals for
output.
DTS Downmix
DTS-HD Master Audio signals, DTS-HD High Resolution
Audio signals or DTS Digital Surround audio signals
converted to linear PCM audio signals are converted into 2-
channel (stereo) signals for output.
Lt/Rt
DTS-HD Master Audio signals, DTS-HD High Resolution
Audio signals or DTS Digital Surround audio signals
converted to linear PCM audio signals are converted into 2-
channel signals compatible with Dolby Surround for output
(when the connected AV receiver or amplifier, etc., is
compatible with Dolby Pro Logic, the AV receiver or amplifier
outputs the linear PCM audio signals as surround audio
signals).
Speakers
Audio Output Mode
2 Channel
Select this when the TV’s analog 2-channel (stereo) audio
input terminals are connected to the player’s AUDIO OUT (2
ch) terminals.
* Only valid for analog
audio outputs.
Multi-channel
Select this when the multi-channel audio input terminals of
an AV receiver or amplifier, etc., are connected to the player’s
AUDIO OUT (7.1 ch) terminals.
Speaker Setup
When an AV receiver or amplifier, etc., is connected to the player’s AUDIO OUT
(7.1 ch) terminals, this sets whether or not to use the speakers which are connected
to the AV receiver or amplifier, as well as the size of the speakers. For details, see
Changing the speaker setup on page 114.
* Only valid for analog
audio outputs.
Channel Level
Fix
The output for the various speakers is set to the maximum.
* Only valid for analog
audio outputs.
Variable
The output level of the various speakers is set within the range
of –6.0 dB to +6.0 dB (in 0.5 dB steps) (page 115).
HDMI
HDMI High-Speed
Transmission
On
Select this when connected with a High Speed HDMI™ cable
(page 77).
Off
Select this when connected with a Standard HDMI™ cable
(page 77).
The player’s setting screen is closed if the output video resolution is switched by changing the HDMI High-
Speed Transmission setting.
When HDMI High-Speed Transmission is set to On, use the supplied HDMI cable.
110
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
06
Setting
HDMI Color Space
Options
Auto
Explanation
The video signal that is output (YCbCr or RGB) is switched
automatically.
YCbCr 4:4:4
Select this to output the video signals as YCbCr 4:4:4 signals.
Select this to output the video signals as YCbCr 4:2:2 signals.
YCbCr 4:2:2
RGB (16 to 235)
Select this to output the video signals as RGB signals.
Choose this if the colors seem too dense and all the dark
colors are displayed in a uniform black when RGB (0 to 255)
is selected.
RGB (0 to 255)
Select this to output the video signals as RGB signals.
Choose this if the colors seem too faint and the black seems
too bright when RGB (16 to 235) is selected.
Normally it is recommended to set this to Auto. When set to Auto, the optimum video signals for your TV are
output.
HDMI Audio Out
Auto
The signals are output with as many audio channels as
possible. In cases when the number of channels does not
decrease when the signals are output as such without
converting them to linear PCM, they are output as such
(page 121).
PCM
Select this when you want the secondary audio and
interactive audio signals to be mixed for output or when you
want to output prioritizing sampling frequency over the
number of channels (page 121).
PQLS
Auto
Off
Enables PQLS function (page 78).
Disables PQLS function (page 78).
HDMI Control
On
Select this to control the player with the remote control of the
AV device connected using an HDMI cable. Also refer to
About HDMI Control function on page 78.
Off
Select this when you do not want to control the player with the
remote control of the AV device connected using an HDMI
cable.
Language
OSD Language
English
Select this to set the language of the on-screen displays to
English.
available languages Choose a language for the on-screen displays from the listed
languages.
111
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
Setting
Options
English
Explanation
Audio Language
Select this to set both the BD-ROM and DVD-Video default
audio language to English.
* For some discs, it may
not be possible to
change to the selected
language.
available languages Choose a language from the listed languages to set the
default audio language for BD-ROM and DVD-Video
playback.
Other
Continue to the next screen to set the default audio language
for BD-ROM and DVD-Video playback. You can select the
language name or enter the code number (see on page 130
for the code table). If a language not recorded on the BD/DVD
is set, one of the recorded languages is automatically
selected and played.
Subtitle Language
English
Select this to set the default subtitle language for BD-ROM
and DVD-Video playback to English.
* For some discs, it may
not be possible to
change to the selected
language.
available languages Choose a language from the listed languages to set the
default subtitle language for BD-ROM and DVD-Video
playback.
Other
Continue to the next screen to set the default subtitle
language for BD-ROM and DVD-Video playback. You can
select the language name or enter the code number (see on
page 130 for the code table). If a language not recorded on
the BD/DVD is set, one of the recorded languages is
automatically selected and played.
BDMV/DVD-Video Menu w/Subtitle
Sets the language of BD-ROM and DVD-VIdeo menus to the
same as that set for the subtitle language.
Lang.
Language
* For some discs, it may
not be possible to
change to the selected
language.
available languages Choose a language from the listed languages to set the
default language for BD-ROM and DVD-Video menus.
Other
Continue to the next screen to set the default menu language
for BD-ROM and DVD-Video menus. You can select the
language name or enter the code number (see on page 130
for the code table). If a language not recorded on the BD/DVD
is set, one of the recorded languages is automatically
selected and played.
Subtitle Display
On
Select this to display the subtitles.
Off
Select this if you do not want to display the subtitles. Note
that on some discs the subtitles are displayed by force.
Parental Lock
Set Password (Change Register (change) the password for parental lock settings or for unlocking to play
Password)
DVD-Video with parental lock feature. For details, see Registering or Changing the
password on page 116.
DVD-Video Parental Lock Change the player’s parental lock level. For details, see Changing the Parental Lock
level for watching DVDs on page 117.
BDMV Parental Lock
Change the restricted age. For details, see Changing the Age Restriction for watching
BD-ROMs on page 117.
112
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
06
Setting
Options
Explanation
Country Code
Change the Country/Area code. Refer to the Changing the Country/Area code on
page 119.
Options
Output Terminal Priority Select the terminals for outputting video and audio signals with priority. For details,
see Changing the terminals for outputting video and audio signals (Output Terminal
Priority) on page 119.
On Screen Display
On
Off
On
Select this to display the operation indicators (Play, Stop,
etc.) on the TV screen.
Select this if you do not want to display the operation
indicators (Play, Stop, etc.) on the TV screen.
Angle/Secondary
Indicator
Select this to display the angle mark, secondary video mark
and secondary audio mark on the TV screen (pages 92 and
94).
Off
Select this if you do not want to display the angle mark,
secondary video mark and secondary audio mark on the TV
screen.
Hybrid Disc Playback
BD
The BD layer of hybrid discs with two or more layers (BD and
DVD or CD) is played.
DVD
CD
The DVD layer of hybrid discs with two or more layers (BD and
DVD) is played. If there is no DVD layer, the BD layer is played.
The CD layer of hybrid discs with two or more layers (BD and
CD) is played. If there is no CD layer, the BD layer is played.
BDMV/BDAV Playback BDMV
Priority
Select this to play the BDMV format on BD-R/-RE discs
containing both BDMV and BDAV formats.
BDAV
Select this to play the BDAV format on BD-R/-RE discs
containing both BDMV and BDAV formats.
DivX VOD
Registration Code
Displays the player’s registration code required to play DivX
VOD files (page 75).
Auto Power Off
On
Select this to turn the power off automatically (the power
turns off automatically if no operation is performed for over 30
minutes).
Off
Select this if you do not want the power to turn off
automatically.
Setup Navigator
Start making the settings using the Setup Navigator menu. For details, see
Important on page 83.
113
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
Changing to other language at
language setting
ENTER
1
Select and set Speakers.
Use / to select, then press ENTER.
Note
• Refer to Language Code Table on page 130.
Initial Setup
BD PLAYER
• If a language not recorded on the BD/DVD
is set, one of the recorded languages is
automatically selected and played.
Video Out
Audio Out
Speakers
HDMI
Audio Output Mode
Speaker Setup
Channel Level
ꢀMulti-channel
ꢀFix
Language
Parental Lock
Options
ENTER
1
Select and set Other.
Setup Navigator
Use / to select, then press ENTER.
ENTER
ENTER
2
Select and set Speaker Setup
2
Change the language.
Next Screen
Use / to select, then press ENTER.
.
Use / to change, then press ENTER.
To change the language using numbers
Caution
• This cannot be selected when Audio
Output Mode is set to 2 Channel. Change
the setting to Multi-channel (page 110).
1
Use
/
to select Number.
1
4
2
5
8
0
3
6
9
7
ENTER
ENTER
CLEAR
2
Use the number buttons
3
Select the speaker and change the
(0 to 9) to input the number, then press
ENTER
setting.
.
Use / to select, then use / to change
the setting.
Changing the speaker setup
Speaker Setup
BD PLAYER
Set whether or not to use the speakers which
are connected to the AV receiver or amplifier,
as well as the size of the speakers. This setting
is only valid for analog audio outputs.
L/R
Large
Yes
C
SL/SR
SBL/SBR
Yes
Yes
Note
Use [
][
] to select a speaker, then press [
to select speaker option.
][
]
• Select Initial Setup from the HOME
MENU, then press ENTER.
• L/R (front left and right speakers): Small/
Large (this setting also applies to the C, SL/
SR and SBL/SBR speakers)
• C (center speaker): Yes/No
114
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
06
• SL/SR (left and right surround speakers):
Yes/No
Caution
• This cannot be selected when Audio
Output Mode is set to 2 Channel. Change
the setting to Multi-channel (page 110).
• SBL/SBR (left and right surround back
speakers): Yes/No
Closing the speaker settings screen
ENTER
•
Press ENTER.
3
Select and set the method for
switching the speaker to be adjusted.
Use / to select, then press ENTER.
Adjusting the output level of the
various speakers (Channel Level)
Adjust each output level of the different
speakers by using test tones. This setting is
only valid for analog audio outputs.
Speaker Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
Test Tone Switching
Select whether test tone output is
switched automatically or manually.
Language
Parental Lock
Options
ENTER
1
Select and set Speakers.
Auto
Manual
Setup Navigator
Use / to select, then press ENTER.
Initial Setup
BD PLAYER
• Auto – Switch the speaker to be adjusted
automatically.
Video Out
Audio Out
Speakers
HDMI
Language
Parental Lock
Options
Audio Output Mode
Speaker Setup
Channel Level
ꢀMulti-channel
• Manual – Switch the speaker to be
adjusted manually.
ꢀFix
Caution
Setup Navigator
• Test tones are output. Lower the volume of
the device connected to the player.
ENTER
2
Select and set Channel Level, then
ENTER
Fix or Variable
Use / to select, then press ENTER.
.
4
Adjust the output level.
Use / to select, / to adjust.
• Fix – The output level of all the speakers is
set to the maximum.
Channel Level
BD PLAYER
L
0.0 dB
• Variable – The output level of all the
speakers is set 6.0 dB lower than when Fix
is selected. From this point, the output
levels of the L, C, R, SL, SR, SBL, SBR and
SW speakers can be adjusted within the
range of –6.0 dB to +6.0 dB.
C
R
0.0 dB
0.0 dB
0.0 dB
0.0 dB
0.0 dB
0.0 dB
0.0 dB
SR
SBR
SBL
SL
SW
Use [
][
] to select a speaker, then press [
to adjust the channel level and then press ENTER.
][
]
• If you have selected Variable, proceed to
step 3.
115
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
Initial Setup
BD PLAYER
Note
Video Out
Audio Out
Speakers
HDMI
Set Password
• When Auto is selected, the speaker
cannot be selected with /.
Enter new password
Language
Parental Lock
Options
Closing the Channel Level screen
Setup Navigator
•
Press ENTER.
Registering or Changing the
password
Use this procedure to register or change the
code number required for the Parental Lock
settings.
1
4
7
2
5
8
0
3
6
9
ENTER
4
Re-input the password.
Use the number buttons (0 to 9) or / to
input the number, then press ENTER to set.
BD
Movie files
Music files
Use / to move the cursor.
DVD
AVCHD
CD
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
Set Password
Enter new password
ENTER
1
Select and set Parental Lock
.
Language
Parental Lock
Options
Re-enter
Use / to select, then press ENTER.
Setup Navigator
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
Language
Parental Lock
Options
Set Password
DVD-Video Parental Lock
BDMV Parental Lock
Country Code
ꢀOff
ꢀ255
ꢀus
To change the code number
Input the previously registered password, then
input the new password.
Setup Navigator
Note
• We recommend making a note of the
password.
ENTER
• If you forget the password, reset the player
to the factory default setting, then register
the password again (page 120).
2
Select and set Set Password
Next Screen
Use / to select, then press ENTER.
.
1
4
7
2
5
8
0
3
6
9
ENTER
3
Input the password.
Use the number buttons (0 to 9) or / to
input the number, then press ENTER to set.
Use / to move the cursor.
116
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
06
1
4
7
2
5
8
0
3
6
9
Changing the Age Restriction for
watching BD-ROMs
For BD-ROMs containing scenes of violence,
for example, watching can be restricted by
setting an age restriction for the BD-ROMs.
ENTER
4
Change the age.
Use the number buttons (0 to 9) or / to
input the number, then press ENTER to set.
Use / to move the cursor.
BD
Movie files
Music files
DVD
AVCHD
CD
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
BDMV Parental Lock
Age Restriction
ENTER
Language
Parental Lock
Options
1
Select and set Parental Lock.
Use / to select, then press ENTER.
Setup Navigator
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
Language
Parental Lock
Options
Set Password
DVD-Video Parental Lock
BDMV Parental Lock
Country Code
ꢀOff
ꢀ255
ꢀus
Note
• When Age Restriction is set to 255,
watching is not restricted.
Setup Navigator
Changing the Parental Lock level for
watching DVDs
Some DVD-Video discs containing scenes of
violence, for example, have Parental Lock
levels (check the indications on the disc’s
jacket or elsewhere). To restrict watching these
discs, set the player’s level to the level lower
than the discs.
ENTER
2
Select and set BDMV Parental
Lock Next Screen
Use / to select, then press ENTER.
.
1
4
7
2
5
8
0
3
6
9
BD
Movie files
Music files
ENTER
DVD
AVCHD
CD
3
Input the password.
Use the number buttons (0 to 9) or / to
input the number, then press ENTER to set.
Use / to move the cursor.
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
BDMV Parental Lock
Enter the password
Language
Parental Lock
Options
Setup Navigator
117
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
ENTER
ENTER
4
Change the level.
1
Select and set Parental Lock
.
Use / to change, then press ENTER to set.
Use / to select, then press ENTER.
Initial Setup
BD PLAYER
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
DVD-Video Parental Lock
Level
Video Out
Audio Out
Speakers
HDMI
Set Password
DVD-Video Parental Lock
BDMV Parental Lock
Country Code
ꢀOff
ꢀ255
ꢀus
Off
Language
Parental Lock
Options
Language
Parental Lock
Options
Setup Navigator
Setup Navigator
ENTER
Note
2
Select and set DVD-Video
Parental Lock Next Screen
Use / to select, then press ENTER.
• The level can be set to Off or between
Level1 and Level8. When set to Off,
watching is not restricted.
.
1
4
7
2
5
8
0
3
6
9
ENTER
3
Input the password.
Use the number buttons (0 to 9) or / to
input the number, then press ENTER to set.
Use / to move the cursor.
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
DVD-Video Parental Lock
Enter the password
Language
Parental Lock
Options
Setup Navigator
118
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
06
Changing the Country/Area code
ENTER
BD
Movie files
Music files
4
Change the country/area code.
DVD
AVCHD
CD
Use / to change, then press ENTER to set.
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
Language
Parental Lock
Options
Country Code
Code
Note
• Refer to Country/Area Code Table on
page 131.
Number
Setup Navigator
ENTER
1
Select and set Parental Lock.
Use / to select, then press ENTER.
To change the country/area code using
numbers
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
Set Password
DVD-Video Parental Lock
BDMV Parental Lock
Country Code
ꢀOff
ꢀ255
ꢀus
1
Use
/
to select Number.
Language
Parental Lock
Options
1
4
7
2
5
8
0
3
6
9
Setup Navigator
ENTER
2
Use the number buttons
(0 to 9) to input the number, then press
ENTER
.
ENTER
2
Select and set Country/Area
Changing the terminals for
Code
.
outputting video and audio signals
(Output Terminal Priority)
Use / to select, then press ENTER.
1
4
7
2
5
8
0
3
6
9
Set the video and audio terminals to be used.
ENTER
3
Input the password.
ENTER
Use the number buttons (0 to 9) or / to
1
Select and set Options.
input the number, then press ENTER to set.
Use / to select, then press ENTER.
Use / to move the cursor.
Initial Setup
BD PLAYER
Initial Setup
BD PLAYER
Video Out
Audio Out
Speakers
HDMI
Output Terminal Priority
On Screen Display
Video Out
Audio Out
Speakers
HDMI
Country Code
ꢀOn
Angle/Secondary Indicator ꢀOn
Hybrid Disc Playback ꢀBD
Enter the password
Language
Parental Lock
Options
BDMV/BDAV Playback Priority ꢀBDAV
DivX VOD
Language
Parental Lock
Options
Auto Power Off
ꢀOn
Setup Navigator
Setup Navigator
119
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
ENTER
ENTER
2
Select and set Output Terminal
Priority Next Screen
Use / to select, then press ENTER.
4
Select the terminal for outputting
.
audio signals.
Use / to select, then press ENTER.
• HDMI – HDMI OUT terminal
• Digital Audio – DIGITAL OUT (OPTICAL)
terminal
3
Select the terminal for outputting
video signals.
Use / to select, then press .
• Analog Audio – AUDIO OUT (2 ch)
terminals or AUDIO OUT (7.1 ch)
terminals
When a digital output is selected for the video
output terminal, Video is fixed at HDMI and
cannot be changed.
The optimum audio signals for the audio
format and the player’s settings are output
from the output terminal(s) set here.
When an analog output is selected for the
video output terminal, Component Video or
S-Video/Video can be selected for Video.
Caution
Initial Setup
BD PLAYER
• Linear PCM (2-channel) audio signals are
output from the audio terminals other than
the one set at Audio, regardless of the
audio format and the player’s settings.
Video Out
Audio Out
Speakers
HDMI
Output Terminal Priority
Video
Audio
S-Video/Video
Analog Audio
Language
Parental Lock
Options
Restoring all the settings to the
factory default settings
Setup Navigator
1
on.
Check that the player’s power is turned
• HDMI – HDMI OUT terminal
• Component Video – COMPONENT
VIDEO output terminals
2
When a disc is playing, press STOP to
stop playback.
Eject the disc from the player.
• S-Video/Video – S-VIDEO output terminal
or VIDEO output terminal
3
While pressing STOP, press
The video and audio signals output from the set
output terminals are output synchronously (lip
synchronization).
STANDBY/ON
Operate using the buttons on the player’s front
panel.
.
Caution
Note
• If the output terminal you want to select at
Video is not displayed, use the VIDEO
SELECT button to switch between digital
and analog output (page 87).
• After restoring all the settings to the factory
default settings, use Setup Navigator to
reset the player (page 83).
120
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced settings
06
About the audio output settings
The audio signals that are output differ according to the audio format recorded on the disc and the
player’s settings. Check on the table below.
1
AUDIO OUT terminal
DIGITAL OUT terminal
HDMI OUT terminal
Not
Converted to
Audio format
Multi-
converted to
2
6
6,7,8
linear PCM
2ch
PCM
Auto
2
linear PCM
channel
3
audio
4,5
audio
Dolby Digital
5.1-channel
audio
5.1-channel
audio
Dolby Digital
Dolby Digital
Plus
Dolby Digital
Dolby Digital
Plus
7.1-channel
7.1-channel
9
9,10
audio
audio
11
Dolby TrueHD
Dolby TrueHD
DTS Digital
Surround
5.1-channel
audio
5.1-channel
audio
DTS Digital
Surround
Converted to 2-
channel audio
Converted to 2-
channel audio
DTS-HD High
Resolution Audio
DTS Digital
Surround
DTS-HD High
Resolution Audio
5.1-channel
5.1-channel
12
12
audio
audio
DTS-HD Master
Audio
DTS-HD Master
13
Audio
Linear PCM
7.1-channel
Converted to 2- 7.1-channel
7.1-channel
9
9,10
9,10
audio
channel audio audio
audio
Dolby Digital
MPEG-2 AAC
MPEG
Dolby Digital
MPEG-2 AAC
Dolby Digital
MPEG-2 AAC
Converted to 2- 5.1-channel Converted to 2-
channel audio audio channel audio
5.1-channel
audio
2-channel audio
Linear PCM
Dolby Digital
Dolby Digital
Dolby Digital
Converted to 2- 5.1-channel Converted to 2-
channel audio audio channel audio
5.1-channel
audio
DTS Digital
Surround
DTS Digital
Surround
DTS Digital
Surround
MPEG
2-channel audio
Linear PCM
Dolby Digital
Converted to 2- 5.1channel Converted to 2-
channel audio audio channel audio
5.1-channel
audio
Dolby Digital
Dolby Digital
MPEG
2-channel audio
Linear PCM
1. When outputting linear PCM audio signals, if the number of compatible channels of the connected HDMI device is
lower, the signals are output with the number of channels for which the device is compatible.
2. When Audio Output Mode is set to 2 Channel or Multi-channel (page 110).
3. When Dolby Digital Out is set to Dolby Digital PCM, DTS Out is set to DTS PCM, or AAC Out is set to AAC
PCM (page 109).
4. When Dolby Digital Out is set to Dolby Digital 1/Dolby Digital 2, DTS Out is set to DTS 1/DTS 2 or AAC Out is
set to AAC (page 109).
5. When outputting Dolby Digital or DTS Digital Surround bitstream with settings of Dolby Digital 2 at Dolby Digital
Out, DTS 2 at DTS Out, the secondary audio and interactive audio signals are not mixed for output.
6. When HDMI Audio Out is set to PCM or Auto (page 111).
7. When outputting the bitstream of Dolby TrueHD, Dolby Digital Plus, Dolby Digital, DTS-HD Master Audio, DTS-HD
High Resolution Audio or DTS Digital Surround, the secondary audio and interactive audio signals are not mixed.
121
En
Download from Www.Somanuals.com. All Manuals Search And Download.
06
Advanced settings
8. If the connected HDMI device is not compatible with Dolby TrueHD or Dolby Digital Plus bitstream, the signals are
output in Dolby Digital bitstream.
If the connected HDMI device is not compatible with DTS-HD Master Audio or DTS-HD High Resolution Audio, the
signals are output in DTS Digital Surround bitstream.
If the connected HDMI device is not compatible with Dolby Digital or DTS Digital Surround bitstream, the signals
are output in linear PCM.
9. Only compatible with 7.1-channel surround back. 6.1-channel surround back is output in 7.1 channels. In other cas-
es, output as audio signals of 5.1-channels or less.
10. When the output video resolution is set to 576i/480i or 576p/480p, the signals may be output in 2 channel, depending
on HDMI High-Speed Transmission setting and/or the connected HDMI device (page 77).
11. When the output video resolution is set to 576i/480i or 576p/480p, the signals may be output in Dolby Digital bit-
stream, depending on HDMI High-Speed Transmission setting and/or the connected HDMI device (page 77).
12. DTS Digital Surround signals converted to linear PCM audio signals are output.
13. When the output video resolution is set to 576i/480i or 576p/480p, the signals may be output in DTS Digital Surround
bitstream, depending on HDMI High-Speed Transmission setting and/or the connected HDMI device (page 77).
Caution
• Linear PCM audio signals (2 channels) are output from all terminals other than the ones
selected at Audio under Output Terminal Priority, regardless of the audio format or the
player’s settings (pages 83 and 119).
• The audio signals output from the DIGITAL OUT terminals have a sampling frequency of 48
kHz (44.1 kHz for CDs).
• MPEG audio is output in linear PCM.
• When connected to this receiver using the HDMI jacks, the audio signals are converted as
below for output from this player.
– Dolby TrueHD signals are decoded by this player and output as 5.1-channel (or fewer) linear
PCM signals.
– Dolby Digital Plus signals are output as a Dolby Digital bitstream.
– DTS-HD Master Audio or DTS-HD High Resolution Audio signals are output as a DTS Digital
Surround bitstream.
– MPEG-2 AAC signals are decoded by this player and output as 2-channel linear PCM
signals.
– 7.1-channel linear PCM signals are downmixed to 5.1 channels for output.
122
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
07
Chapter 7
Additional information
Troubleshooting
Incorrect operation is often mistaken for trouble or malfunction. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Inspect the other components and electrical appliances being used. If the
trouble cannot be rectified even after checking the points below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
Playback
Problem
Check
Remedy
Disc does not play.
Disc tray opens
automatically.
Is the disc scratched?
Is the disc dirty?
It may not be possible to play scratched discs.
Clean the disc (see the Blu-ray disc player’s operating
instructions).
Is the disc properly set in the
disc tray?
• Set the disc with the printed side facing up.
• Set the disc properly in the depression in the disc tray.
Is the region number correct?
The region numbers of discs that can be played on this set
are as shown below (page 74).
• BDs: “B” (or including “B”) and “ALL”
• DVDs: “2” (or including “2”) and “ALL”
Is the player set in a humid
place?
There could be condensation inside. Wait for the
condensation to dissipate. Do not set the player near an air-
conditioner, etc. (see the Blu-ray disc player’s operating
instructions).
Picture freezes and
the front panel and
remote control
• Press (stop) to stop playback, then restart playback.
• If the playback cannot be stopped, press STANDBY/ON
on the player’s front panel to turn off the power, then turn
the power back on.
buttons stop working.
• If the power cannot be turned off, press and hold
STANDBY/ON on the player’s front panel for over 5
seconds. The power will turn off.
123
En
Download from Www.Somanuals.com. All Manuals Search And Download.
07
Additional information
Problem
Check
Remedy
No picture is
displayed or the
picture is not
Is the video cable properly
connected?
Insert the cable firmly and all the way in.
Is the video cable damaged?
Is the input setting on the
If the cable is damaged, replace it with a new one.
Read the operating instructions of the connected
displayed properly.
connected TV or AV receiver or components and switch to the proper input.
amplifier right?
Are the terminals for outputting Press VIDEO SELECT to switch the terminal from which the
video signals properly set?
video signals are output.
Is the output video resolution
properly set?
Depending on the player’s output video resolution, the
picture may not be displayed at all or displayed properly. Use
OUTPUT RESOLUTION to switch to a resolution at which
the picture is displayed properly (page 87).
Is the player connected with an Press STOP while pressing PLAY on the player’s front
HDMI cable other than a High panel to restore the video outputs to the factory default
Speed HDMI™ cable (with a
Standard HDMI™ cable)?
settings. After this, use the Setup Navigator to reset the
player.
There are some BDs for which the picture will only be output
when connected by HDMI cable.
Does the connected TV support If the picture is not displayed when playing a disc with a
the frame rate of the video signal frame rate that is not supported, the picture will not be
being output by the player?
displayed even when playback is stopped. In this case, use
the procedure below to switch the frame rate of the video
signals output from the player. Eject the disc and close the
disc tray. Then, press OPEN/CLOSE while pressing
PLAY on the player’s front panel to switch to a frame rate
supported by the connected TV.
Is NTSC on PAL TV properly set? Set NTSC on PAL TV properly (page 109).
Picture is stretched. Is the TV’s aspect ratio properly Read the TV’s operating instructions and set the TV’s aspect
set?
Is 4:3 Video Out properly set? • Set 4:3 Video Out properly (page 108).
• When video signals with a resolution of 1080/50i, 1080/
ratio properly.
Aspect ratio cannot
be switched.
50p, 720/50p, 1080/24p, 1080/60i, 1080/60p or 720/60p are
being output from the HDMI OUT terminal or the
COMPONENT VIDEO output terminals, they may be output
with an aspect ratio of 16:9 even if TV Aspect Ratio is set to
4:3 (Standard) (page 87).
Sound and picture are Is Output Terminal Priority
Set Output Terminal Priority properly (pages 83 and 119).
not synchronized.
properly set?
Picture is disturbed
during playback.
Picture is dark.
• This player supports Macrovision analog copy protection
technology. With some TVs (such as with built-in video
deck), the picture will not be displayed properly when the
copy protected DVD title is played. This is not a malfunction.
• If the player and TV are connected via a DVD recorder/
video deck, etc., the picture will not be displayed properly
due to analog copy protection. Connect the player and TV
directly.
124
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
07
Problem
Check
Remedy
No picture is
With some content protected discs, it may not be possible to
output the video signals from the VIDEO output terminals,
the S-VIDEO output terminal or the COMPONENT VIDEO
output terminals. In this case, connect using an HDMI cable
(page 76).
displayed or picture is
not output in high
definition when
playing BDs.
No sound is output.
Sound is disturbed.
Is the disc played back in slow No sound is output during slow motion play and forward and
motion?
reverse scanning.
Is the disc played back in fast
forward or fast reverse?
Is the disc scratched?
Is the disc dirty?
The sound may not be output if the disc is scratched.
Clean the disc (see the Blu-ray disc player’s operating
instructions).
Is the player properly connected • Check that you connect the player to the audio output
to the other components (AV
receiver or amplifier, etc.)?
terminals of a different component, etc.
• Check that you connect the player to the PHONO input
terminals of the AV receiver or amplifier, etc.
Are the audio cables properly
connected?
Insert the cables firmly and all the way in.
Is the audio cable damaged?
If the cable is damaged, replace it with a new one.
Is AudioOutput Modeproperly If Audio Output Mode is set to Multi-channel, the audio
set?
signals may not be output properly from the AUDIO OUT (2
ch) terminals (page 109). Set Audio Output Mode to 2
Channel.
Are the speakers properly set?
Set Speaker Setup properly (page 110).
For some BDs, audio signals are only output from the
DIGITAL OUT (OPTICAL) terminal or the HDMI OUT
terminal.
125
En
Download from Www.Somanuals.com. All Manuals Search And Download.
07
Additional information
Problem
Check
Remedy
Multi-channel sound Is the AV receiver or amplifier,
Read the operating instructions of the connected AV
receiver or amplifier and check the audio output settings of
is not output.
etc. connected to the HDMI
OUT terminal, the AUDIO OUT AV receiver or amplifier.
(7.1 ch) terminals or DIGITAL
OUT (OPTICAL) terminal?
Is Output Terminal Priority
properly set?
Linear PCM (2-channel) audio signals are output from
output terminals other than the one set at Audio under
Output Terminal Priority. Set Output Terminal Priority
properly (page 119).
Is the audio output of the
connected AV receiver or
amplifier, etc., properly set?
Read the operating instructions of the connected AV
receiver or amplifier and check the audio output settings of
AV receiver or amplifier.
Is multi-channel sound
selected?
Use the menu screen or AUDIO to switch the disc’s sound
to multi-channel.
Is Audio Out set to audio
formats supported by the
connected AV receiver or
amplifier?
• Read the operating instructions of the connected AV
receiver or amplifier and check the supported audio formats.
• Set Audio Out properly (page 109).
Are Audio Output Mode and • When the AV receiver or amplifier, etc., is connected to the
Speaker Setup properly set?
AUDIO OUT (7.1 ch) terminals, set Audio Output Mode to
Multi-channel (page 110).
• Set Speaker Setup properly (page 110).
Digital audio signals Is Audio Out set to audio
• Read the operating instructions of the connected AV
receiver or amplifier and check the supported audio
formats.
are not output from
formats supported by the
connected AV receiver or
the DIGITAL OUT
(OPTICAL) terminals amplifier?
(analog audio signals
are output).
• Set Audio Out properly (page 109).
Noise can be heard
Is the connected AV receiver or If an AV receiver or amplifier that is not compatible with DTS
when outputting DTS amplifier compatible with DTS Digital Surround is connected to the DIGITAL OUT
Digital Surround
signals.
Digital Surround?
terminal, set DTS Out to DTS PCM. Noise will be heard
if DTS Out is set to DTS (page 109).
192 kHz or 96 kHz
digital audio signals
cannot be output
from the DIGITAL
OUT (OPTICAL)
terminals.
It is not possible to output 192 kHz or 96 kHz digital audio
signals from this player’s DIGITAL OUT (OPTICAL)
terminals. The signals are automatically converted to under
96 kHz for output.
Secondary audio or
interactive audio is
not output.
Is HDMI Audio Out properly
set?
Set HDMI Audio Out to PCM (page 111).
Are Dolby Digital Out and DTS Set Dolby Digital Out to Dolby Digital 1, DTS Out to DTS
Out properly set?
1 (page 109).
Sound is fast or slow. When an HDMI cable is
connected, are audio signals
being output from devices
When this player is connected by HDMI cable to a Pioneer
AV receiver or amplifier compatible with the PQLS function
via HDMI connection, the PQLS function is activated when
playing a music CD (CD-DA). Because of this, the sound
output from components other than the ones connected by
HDMI cable may be fast or slow. If this happens, set PQLS to
Off (page 111).
connected with cables other
than HDMI cables?
126
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
07
Problem
Check
Is the disc one that is playable Check whether the disc is one that can be played on this
on this player? player (page 71).
Is the file one that is playable on • Check whether the file is one that can be played on this
Remedy
Files recorded on
discs cannot be
played.
this player?
player (page 74).
• Check whether or not the file is damaged.
Is the file protected by DRM?
Files protected by DRM cannot be played (not including
DivX VOD files).
A message indicating
low memory (local
storage) appears
while playing a BD-
ROM disc.
Erase the BDMV data (page 87).
When connected using an HDMI cable
Problem
Check
Remedy
HDMI indicator does Is the input of the connected
Read the HDMI device’s operating instructions and set the
input properly.
not light.
HDMI device properly set?
Is a DVI device connected?
Read the DVI device’s operating instructions and check
whether it is compatible with HDCP.
No picture is
displayed.
Is the HDMI indicator lit?
• If the HDMI indicator is not lit, read the HDMI device’s
operating instructions and switch to the proper input.
• If the HDMI indicator is lit, use OUTPUT RESOLUTION to
switch the output video resolution (page 87).
Are the terminals for outputting Press VIDEO SELECT to switch the HDMI OUT terminal.
video signals properly set?
Is the resolution properly set?
Depending on the output video resolution setting, the
picture may not be output. Use OUTPUT RESOLUTION to
switch the output video resolution (page 87).
Is the HDMI cable properly
connected?
• Insert the cable firmly and all the way in.
• With some cables, 1080p video signals cannot be properly
output.
Is a DVI device connected?
Is the HDMI cable damaged?
The picture may not be displayed properly if a DVI device is
connected.
If the cable is damaged, replace it with a new one.
Pictures do not
display properly on
the TV.
Change the HDMI Color Space setting (page 111).
No sound is
produced.
Is a DVI device connected?
The sound will not be output from the HDMI OUT terminal
if a DVI device is connected. Connect the device to a
DIGITAL OUT (OPTICAL) terminal or the AUDIO OUT (2 ch)
terminals.
127
En
Download from Www.Somanuals.com. All Manuals Search And Download.
07
Additional information
Problem
Check
Remedy
HDMI Control
function does not
work.
Is the HDMI cable properly
connected?
Connect the HDMI cable properly.
Is the HDMI cable you are using Use a High Speed HDMI™ cable. The HDMI Control function
a High Speed HDMI™ cable?
may not work properly if HDMI cable other than a High
Speed HDMI™ cable is used.
Is HDMI Control set to On on
Set HDMI Control to On on the player (page 111).
the player?
Does the connected device
support the HDMI Control
function?
• The HDMI Control function will not work with devices
manufactured by companies other than Pioneer, even when
connected using an HDMI cable.
• The HDMI Control function will not work if devices that do
not support the HDMI Control function or devices
manufactured by companies other than Pioneer are
connected between the HDMI Control-compatible device
and the player.
• The HDMI Control function may not work with certain Flat
Screen TVs.
Also refer to the operating instructions of the connected
device.
Is HDMI Control set to On on the Set HDMI Control to On on the connected device. The HDMI
connected device?
Control function works when HDMI Control is set to On for
all the devices connected by HDMI cable.
Once connections and settings of all the devices are
finished, be sure to check that the player’s picture is output
to the Flat Screen TV. (Also check after changing the
connected devices and connecting and/or disconnecting
HDMI cables.) If the player’s picture is not being output to
the Flat Screen TV, the HDMI Control function may not work
properly.
For details, refer to the operating instructions of the
connected device.
Are multiple players connected? The HDMI Control function may not work if three or more
players, including this player, are connected by HDMI cable.
Others
Problem
Check
Remedy
The power turns off
automatically.
Is Auto Power Off set to On? If Auto Power Off is set to On, the power turns off
automatically if no operation is performed for over 30
minutes (page 113).
Is HDMI Control set to On?
The player’s power may turn off together with the power of
the connected TV. If you do not want the player’s power to
turn off when the TV’s power is turned off, set HDMI Control
to Off (page 111).
The power turns on
automatically.
Is HDMI Control set to On?
The player’s power may turn on together with the power of
the connected TV. If you do not want the player’s power to
turn on when the TV’s power is turned on, set HDMI Control
to Off (page 111).
128
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
07
Problem
Check
Remedy
Inputs of connected Is HDMI Control set to On?
TV and this receiver,
switches
The inputs of the connected TV or this receiver may
automatically switch to the player when playback starts on
the player or the menu screen (Home Media Gallery, etc.) is
displayed. If you do not want the inputs of the connected TV
and/or this receiver to switch automatically, set HDMI
Control to Off (page 111).
automatically.
Player cannot be
Is an AV receiver or amplifier
Operate with the remote control of the device connected to
operated with remote connected to the CONTROL IN the CONTROL IN terminal.
control.
terminal on the player’s rear
panel?
Are you operating the remote
control from a point too far away
from the player?
Operate from within 7 m of the remote control sensor.
Are the batteries dead?
Replace the batteries (page 9).
Settings you have
made have been
cleared.
• Have you disconnected the
power cord while the player’s
power was on?
• Has there been a power
failure?
If the power cord is disconnected or there is a power failure
while the player’s power is on, the settings you have made
may be cleared. Always press STANDBY/ON on the
player’s front panel or BD on the remote control and
check that POWER OFF has turned off from the player’s
front panel display before disconnecting the power cord. Be
particularly careful when the power cord is connected to the
AC outlet on another device because the player turns off in
conjunction with the device. We recommend plugging the
power cord into a wall outlet whenever possible.
After a disc is
inserted, Loading
stays displayed and
playback does not
start.
Are there too many files
recorded on the disc?
When a disc on which files are recorded is inserted,
depending on the number of files recorded on the disc,
loading may take several dozen minutes.
is displayed in file
names, etc.
The characters that cannot be displayed on this player are
displayed in .
The DVD layer of BD Is Hybrid Disc Playback
and DVD hybrid discs properly set?
cannot be played.
Set Hybrid Disc Playback to DVD (page 113).
The CD layer of BD
Is Hybrid Disc Playback
Set Hybrid Disc Playback to CD (page 113).
and CD hybrid discs properly set?
cannot be played.
The Hybrid Disc
Playback setting
cannot be changed
(displayed in gray).
Is a disc set in the disc tray?
The Hybrid Disc Playback setting cannot be changed when
a disc is set. Remove the disc, then change the setting.
BDMV/BDAV
Is a disc set in the disc tray?
The BDMV/BDAV Playback Priority setting cannot be
changed when a disc is set. Remove the disc, then change
the setting.
Playback Priority
setting cannot be
changed (displayed in
gray).
129
En
Download from Www.Somanuals.com. All Manuals Search And Download.
07
Additional information
Language Code Table and Country/Area Code Table
Language Code Table
Language name (language code), input code
Japanese (ja/jpn), 1001
English (en/eng), 0514
French (fr/fra), 0618
German (de/deu), 0405
Italian (it/ita), 0920
Spanish (es/spa), 0519
Chinese (zh/zho), 2608
Dutch (nl/nld), 1412
Portuguese (pt/por), 1620
Swedish (sv/swe), 1922
Russian (ru/rus), 1821
Korean (ko/kor), 1115
Greek (el/ell), 0512
Esperanto (eo/epo), 0515
Estonian (et/est), 0520
Basque (eu/eus), 0521
Persian (fa/fas), 0601
Finnish (fi/fin), 0609
Fijian (fj/fij), 0610
Faroese (fo/fao), 0615
Frisian (fy/fry), 0625
Lingala (ln/lin), 1214
Lao (lo/lao), 1215
Lithuanian (lt/lit), 1220
Latvian (lv/lav), 1222
Malagasy (mg/mlg), 1307
Maori (mi/mri), 1309
Samoan (sm/smo), 1913
Shona (sn/sna), 1914
Somali (so/som), 1915
Albanian (sq/sqi), 1917
Serbian (sr/srp), 1918
Swati (ss/ssw), 1919
Macedonian (mk/mkd), 1311 Sotho, Southern (st/sot), 1920
Malayalam (ml/mal), 1312
Mongolian (mn/mon), 1314
Moldavian (mo/mol), 1315
Marathi (mr/mar), 1318
Malay (ms/msa), 1319
Maltese (mt/mlt), 1320
Burmese (my/mya), 1325
Nauru (na/nau), 1401
Nepali (ne/nep), 1405
Norwegian (no/nor), 1415
Occitan (oc/oci), 1503
Oromo (om/orm), 1513
Oriya (or/ori), 1518
Panjabi (pa/pan), 1601
Polish (pl/pol), 1612
Pushto (ps/pus), 1619
Quechua (qu/que), 1721
Rhaeto-Romance (rm/roh), 1813 Urdu (ur/urd), 2118
Rundi (rn/run), 1814
Romanian (ro/ron), 1815
Kinyarwanda (rw/kin), 1823
Sanskrit (sa/san), 1901
Sindhi (sd/snd), 1904
Sango (sg/sag), 1907
Serbo-Croatian (sh/scr), 1908 Zulu (zu/zul), 2621
Sinhalese (si/sin), 1909
Slovak (sk/slk), 1911
Slovenian (sl/slv), 1912
Sundanese (su/sun), 1921
Swahili (sw/swa), 1923
Tamil (ta/tam), 2001
Telugu (te/tel), 2005
Tajik (tg/tgk), 2007
Irish (ga/gle), 0701
Scots-Gaelic (gd/gla), 0704
Galician (gl/glg), 0712
Guarani (gn/grn), 0714
Gujarati (gu/guj), 0721
Hausa (ha/hau), 0801
Hindi (hi/hin), 0809
Croatian (hr/hrv), 0818
Hungarian (hu/hun), 0821
Armenian (hy/hye), 0825
Interlingua (ia/ina), 0901
Interlingue (ie/ile), 0905
Inupiaq (ik/ipk), 0911
Indonesian (in/ind), 0914
Icelandic (is/isl), 0919
Hebrew (iw/heb), 0923
Yiddish (ji/yid), 1009
Javanese (jw/jav), 1023
Georgian (ka/kat), 1101
Kazakh (kk/kaz), 1111
Kalaallisut (kl/kal), 1112
Khmer (km/khm), 1113
Kannada (kn/kan), 1114
Kashmiri (ks/kas), 1119
Kurdish (ku/kur), 1121
Kirghiz (ky/kir), 1125
Latin (la/lat), 1201
Thai (th/tha), 2008
Afar (aa/aar), 0101
Tigrinya (ti/tir), 2009
Turkmen (tk/tuk), 2011
Tagalog (tl/tgl), 2012
Tswana (tn/tsn), 2014
Tonga (Tonga Islands) (to/
ton), 2015
Turkish (tr/tur), 2018
Tsonga (ts/tso), 2019
Tatar (tt/tat), 2020
Abkhazian (ab/abk), 0102
Afrikaans (af/afr), 0106
Amharic (am/amh), 0113
Arabic (ar/ara), 0118
Assamese (as/asm), 0119
Aymara (ay/aym), 0125
Azerbaijani (az/aze), 0126
Bashkir (ba/bak), 0201
Belarusian (be/bel), 0205
Bulgarian (bg/bul), 0207
Bihari (bh/bih), 0208
Bislama (bi/bis), 0209
Bengali (bn/ben), 0214
Tibetan (bo/bod), 0215
Breton (br/bre), 0218
Catalan (ca/cat), 0301
Corsican (co/cos), 0315
Czech (cs/ces), 0319
Welsh (cy/cym), 0325
Danish (da/dan), 0401
Dzongkha (dz/dzo), 0426
Twi (tw/twi), 2023
Ukrainian (uk/ukr), 2111
Uzbek (uz/uzb), 2126
Vietnamese (vi/vie), 2209
Volapük (vo/vol), 2215
Wolof (wo/wol), 2315
Xhosa (xh/xho), 2408
Yoruba (yo/yor), 2515
130
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
07
Country/Area Code Table
Country/Area name, input code, Country/Area code
Anguilla, 0109, ai
Antigua and Barbuda,
0107, ag
Estonia, 0505, ee
Finland, 0609, fi
France, 0618, fr
Georgia, 0705, ge
Germany, 0405, de
Greece, 0718, gr
Greenland, 0712, gl
Grenada, 0704, gd
Guyana, 0725, gy
Haiti, 0820, ht
Hong Kong, 0811, hk
Hungary, 0821, hu
Iceland, 0919, is
India, 0914, in
Indonesia, 0904, id
Ireland, 0905, ie
Israel, 0912, il
Macedonia, the Former Yu- Singapore, 1907, sg
goslav Republic of, 1311, Slovakia, 1911, sk
mk
Slovenia, 1909, si
Spain, 0519, es
Suriname, 1918, sr
Sweden, 1905, se
Switzerland, 0308, ch
Taiwan, Province of China,
2023, tw
Tajikistan, 2010, tj
Thailand, 2008, th
Trinidad and Tobago,
2020, tt
Tunisia, 2014, tn
Turkey, 2018, tr
Argentina, 0118, ar
Armenia, 0113, am
Australia, 0121, au
Austria, 0120, at
Azerbaijan, 0126, az
Bahamas, 0219, bs
Barbados, 0202, bb
Belarus, 0225, by
Belgium, 0205, be
Belize, 0226, bz
Bermuda, 0213, bm
Brazil, 0218, br
Bulgaria, 0207, bg
Canada, 0301, ca
Cayman Islands, 1125, ky
Chile, 0312, cl
Malaysia, 1325, my
Malta, 1320, mt
Mexico, 1324, mx
Moldova, Republic of,
1304, md
Monaco, 1303, mc
Montserrat, 1319, ms
Netherlands, 1412, nl
New Zealand, 1426, nz
Norway, 1415, no
Pakistan, 1611, pk
Peru, 1605, pe
Philippines, 1608, ph
Poland, 1612, pl
Portugal, 1620, pt
Puerto Rico, 1618, pr
Romania, 1815, ro
Turkmenistan, 2013, tm
Turks and Caicos Islands,
2003, tc
Ukraine, 2101, ua
United Kingdom, 0702, gb
Italy, 0920, it
Jamaica, 1013, jm
Japan, 1016, jp
China, 0314, cn
Colombia, 0315, co
Croatia, 0818, hr
Cyprus, 0325, cy
Czech Republic, 0326, cz
Denmark, 0411, dk
Dominica, 0413, dm
Dominican Republic,
0415, do
Kazakhstan, 1126, kz
Korea, Republic of, 1118,
kr
Kyrgyzstan, 1107, kg
Latvia, 1222, lv
Liechtenstein, 1209, li
Lithuania, 1220, lt
Luxembourg, 1221, lu
Russian Federation, 1821, United States, 2119, us
ru
Uruguay, 2125, uy
Uzbekistan, 2126, uz
Venezuela, 2205, ve
Virgin Islands, British,
2207, vg
Saint Kitts and Nevis,
1114, kn
Saint Lucia, 1203, lc
Saint Vincent and the Grena-
dines, 2203, vc
San Marino, 1913, sm
131
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Discover the benefits of registering your product online at
http://www.pioneer.co.uk (or http://www.pioneer.eu)
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270
K002_B_En
Published by Pioneer Corporation.
Copyright © 2008 Pioneer Corporation.
All rights reserved.
<XRB3100-A>
Printed in
Download from Www.Somanuals.com. All Manuals Search And Download.
|
