Pioneer Flat Panel Television PRO 920HD User Manual
PLASMA DISPLAY SYSTEM  
PRO-1120HD  
PRO-920HD  
Register Your Product on  
www.pioneerelectronics.com  
Operating Instructions  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION:  
WARNING: THE APPARATUS IS NOT WATER-  
PROOFS, TO PREVENT FIRE OR SHOCK HAZARD, DO  
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE  
AND DO NOT PUT ANY WATER SOURCE NEAR THIS  
APPARATUS, SUCH AS VASE, FLOWER POT, COSMET-  
ICS CONTAINER AND MEDICINE BOTTLE ETC.  
This product satisfies FCC regulations when shielded  
cables and connectors are used to connect the unit to  
other equipment. To prevent electromagnetic interfer-  
ence with electric appliances such as radios and televi-  
sions, use shielded cables and connectors for connec-  
tions.  
WARNING: Handling the cord on this product or  
cords associated with accessories sold with the prod-  
uct will expose you to lead, a chemical known to the  
State of California and other governmental entities to  
cause cancer and birth defects or other reproductive  
harm. Wash hands after handling.  
FEDERAL COMMUNICATIONS COMMISSION  
DECLARATION OF CONFORMITY  
This device complies with part 15 of the FCC Rules. Op-  
eration is subject to the following two conditions: (1) This  
device may not cause harmful interference, and (2) this  
device must accept any interference received, including  
interference that may cause undesired operation.  
NOTE: This equipment has been tested and found to  
comply with the limits for a class B digital device, pur-  
suant to Part 15 of the FCC Rules. These limits are de-  
signed to provide reasonable protection against harmful  
interference in a residential installation. This equipment  
generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that  
interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio  
or television reception, which can be determined by turn-  
ing the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the fol-  
lowing measures:  
Product Name:  
Plasma Display System  
(Plasma Display)  
(Media Receiver)  
Model Number:  
PRO-1120HD  
(PRO-505PU)  
(PRO-R05U)  
PRO-920HD  
(PRO-435PU)  
(PRO-R05U)  
Product Category: Class B Personal Computers & Periph-  
erals  
Responsible Party Name: PIONEER ELECTRONICS  
(USA), INC., Customer Support Div.  
Address: P.O. BOX 1760, LONG BEACH, CA., 90801-1760  
U.S.A.  
Phone: (800) 421-1625  
— Reorient or relocate the receiving antenna.  
— Increase the separation between the equipment and  
receiver.  
— Connect the equipment into an outlet on a circuit  
different from that to which the receiver is connected.  
For Business Customer URL  
http://www.PioneerUSA.com  
— Consult the dealer or an experienced radio/TV tech-  
nician for help.  
IMPORTANT NOTICE: The serial number for this  
equipment is located on the rear panel. Please write this  
serial number on your enclosed warranty card and keep  
it in a secure area. This is for your security.  
Information to User  
Alteration or modifications carried out without appro-  
priate authorization may invalidate the user’s right to  
operate the equipment.  
WARNING: Be sure to plug this equipment into a  
grounding-type AC outlet.  
[For Canadian model]  
This Class B digital apparatus complies with Canadian  
ICES-003.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Thank you for buying this Pioneer product.  
Please read through these operating instructions so you will know how to operate your model properly. After you have finished  
reading the instructions, put them away in a safe place for future reference.  
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explana-  
tory drawings. However the method of connecting and operating the unit is the same.  
Using the multiscreen functions ....................................... 28  
Splitting the screen ...................................................... 28  
Freezing images ............................................................ 29  
01 Important User Guidance Information  
02 Safety Precautions  
03 Operational Precautions  
08 Menu Setup  
Menu configuration ............................................................ 30  
AV mode menus............................................................ 30  
PC mode menus ........................................................... 30  
Menu operations ................................................................. 30  
04 Supplied Accessories  
Plasma Display ................................................................... 11  
Media Receiver.................................................................... 11  
05 Part Names  
09 Tuner Setup  
Plasma Display ................................................................... 12  
Media Receiver.................................................................... 12  
Remote control unit ............................................................ 14  
Setting up TV channels ...................................................... 31  
Using Auto Channel Preset ......................................... 31  
Setting for skipping unwanted channels.................... 31  
Setting up TV channels manually ............................... 31  
Naming TV channels .................................................... 32  
Checking signal strength ............................................. 32  
Checking the Cable Card ID ........................................ 32  
Enabling data acquisition ............................................ 32  
Parental Control .................................................................. 33  
Changing the password ............................................... 33  
Clearing the password ................................................. 34  
Activating the Parental Control ................................... 34  
Setting the voluntary movie rating system  
06 Preparation  
Installing the Plasma Display ............................................ 15  
Installing the Media Receiver ............................................ 16  
Installing the Media Receiver vertically ...................... 16  
Connecting the system cable ............................................ 18  
Routing cables .................................................................... 19  
Preparing the remote control unit ..................................... 20  
Inserting batteries......................................................... 20  
Cautions regarding batteries ....................................... 20  
Allowed operation range of the remote  
(MPAA) .......................................................................... 34  
Setting the TV ratings ................................................... 35  
Setting the TV Parental Guidelines (TV Guidelines) ... 35  
Blocking Not Rated TV programs ................................ 35  
Canadian rating systems ............................................. 36  
Setting Canadian English ratings ............................... 36  
Setting Canadian French ratings ................................ 37  
Temporarily deactivating the Parental Control ........... 37  
Setting your favorite channels ........................................... 37  
Setting up closed captions ................................................ 37  
Activating the closed caption ...................................... 38  
Selecting the type of conventional closed captions .. 38  
Selecting digital closed captions ................................ 38  
Selecting digital closed caption parameters ............. 38  
Clock Setting ....................................................................... 39  
control unit .................................................................... 20  
Cautions regarding the remote control unit .............. 20  
Cable connections for watching digital and/or  
conventional TV channels .................................................. 21  
Connecting VHF/UHF antennas and a Cable  
Converter ....................................................................... 21  
Cable connections for watching digital  
TV channels over air (VHF/UHF) ........................................ 21  
Connecting VHF/UHF antennas .................................. 21  
Switching between antenna A and B ............................... 22  
Inserting the cable card ..................................................... 22  
Connecting the power cord ............................................... 23  
07 Basic Operations  
Turning on the power (Standby) ........................................ 24  
Turning off the power (Standby) ........................................ 24  
Watching TV channels........................................................ 25  
Selecting the antenna .................................................. 25  
Changing channels ...................................................... 25  
Changing the volume and sound ................................ 26  
Viewing a channel banner ........................................... 26  
Using the POD service ................................................. 27  
Changing the language................................................ 27  
Setting MTS/SAP mode ............................................... 27  
4
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Connecting other audio equipment .................................. 53  
Connecting an AV receiver .......................................... 53  
Watching a D-VHS image................................................... 54  
What is i.LINK?.............................................................. 54  
Which i.LINK devices are connectable? ..................... 54  
What can be recorded through i.LINK? ...................... 54  
Connecting D-VHS recorders ...................................... 54  
When connecting a single D-VHS recorder ............... 54  
When connecting two D-VHS recorders..................... 54  
Displaying a D-VHS image ................................................. 55  
Useful and important notification ............................... 55  
Setting up for controlling a D-VHS recorder .............. 56  
Editing the i.LINK list.................................................... 56  
Setting up for i.LINK standby....................................... 57  
Operating the control panel screen ............................ 57  
Watching an image from a personal computer ............... 58  
Connecting a personal computer ............................... 58  
Displaying an image from a personal computer ....... 58  
Computer compatibility chart ............................................ 58  
Connecting the VCR controller .......................................... 59  
The lists of controllable recording  
10 Adjustments and Settings  
Sleep Timer .......................................................................... 40  
AV Selection ........................................................................ 40  
Picture adjustments ........................................................... 41  
Pro Adjust ...................................................................... 41  
Color Management ....................................................... 42  
Sound adjustments ............................................................ 43  
FOCUS ........................................................................... 43  
Front Surround .............................................................. 43  
Power Control ...................................................................... 44  
Energy Save ................................................................... 44  
No Signal off (AV mode only) ....................................... 44  
No Operation off (AV mode only)................................. 44  
Power Management (PC mode only) .......................... 44  
Adjusting image positions (AV mode only) ...................... 45  
Adjusting image positions and clock automatically  
(PC mode only) .................................................................... 45  
Adjusting image positions and clock manually  
(PC mode only) .................................................................... 45  
Selecting a screen size ....................................................... 46  
Changing the brightness at both sides of the screen  
(Side Mask) .......................................................................... 47  
Language setting ................................................................ 47  
equipment manufactures ............................................ 60  
Connecting control cords .................................................. 61  
About SR+ .................................................................... 61  
11 Timer Presetting  
13 Useful Remote Control Features  
Presetting TV programs using the timer ........................... 48  
Priority rules for overlapped presettings ........................... 49  
Learning function of the remote control unit ................... 62  
Using the learning function ......................................... 62  
Presetting manufacture codes .................................... 62  
Manufacture codes ...................................................... 63  
Using the remote control unit to control other  
devices ................................................................................. 64  
Receiver control buttons .............................................. 64  
Cable control buttons ................................................... 65  
SAT control buttons ...................................................... 66  
VCR control buttons ..................................................... 67  
DVD/DVR control buttons ............................................ 68  
12 Enjoying through External Equipment  
Watching a DVD image ...................................................... 50  
Connecting a DVD player............................................. 50  
Displaying a DVD image .............................................. 50  
Watching a VCR image ...................................................... 50  
Connecting a VCR ........................................................ 50  
Displaying a VCR image............................................... 50  
Using HDMI Input ............................................................... 51  
Connecting HDMI equipment ..................................... 51  
Enjoying a game console or watching camcorder  
14 Appendix  
images ................................................................................. 52  
Connecting a game console or camcorder ................ 52  
Displaying an image of the game console or  
Troubleshooting .................................................................. 69  
Specifications ...................................................................... 79  
camcorder ..................................................................... 52  
Recording digital TV programs using a VCR or  
DVD recorder....................................................................... 52  
Avoiding unwanted feedback ...................................... 52  
Connecting a recorder ................................................. 53  
5
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01  
Important User Guidance Information  
In order to obtain maximum enjoyment from this Pioneer  
PureVision PRO-1120HD/PRO-920HD Plasma Display System,  
please first read this information carefully.  
With the Pioneer PureVision PRO-1120HD/PRO-920HD, you can  
be assured of a high quality Plasma Display System with long-  
life and high reliability. To achieve images of exceptional quality,  
this Pioneer Plasma Display System incorporates state-of-the-  
art design and construction, as well as very precise and highly  
advanced technology.  
The Pioneer PureVision PRO-1120HD/PRO-920HD incorporates  
the latest in color filter technology – 1st Surface Pure Color  
Filter. This improves the color / picture reproduction of these  
models as compared to previous models. It also eliminates the  
need for a physical glass panel to be placed in front of the  
plasma panel, which furthers Pioneer’s continued goal of  
reducing environmental waste in consumer electronics, now  
during the manufacturing process and in the future during the  
recycling process.  
Installation guidelines  
The Pioneer PureVision PRO-1120HD/PRO-920HD Plasma  
Display System incorporates a very thin design. To ensure  
safety, please take the proper measures to mount or install the  
Plasma Display, in order to prevent the unit from tipping over in  
the event of vibration or accidental movement.  
This product should be installed by using only parts and  
accessories designed by PIONEER. Use of accessories other  
than the PIONEER stand or installation bracket may result in  
instability, and could cause injury. For custom installation,  
please consult the dealer where the unit was purchased. To  
ensure correct installation, experienced and qualified experts  
must install the unit. PIONEER will not be held responsible for  
accident or damage caused by the use of parts and accessories  
manufactured by other companies.  
To avoid malfunction and overheating when installing, make  
sure that the vents on the main unit are not blocked. To ensure  
proper heat emission:  
Over the course of its lifetime, the luminosity of the Pioneer  
PRO-1120HD/PRO-920HD Plasma Display System will diminish  
very slowly, such as with all phosphor-based screens (for  
example, a traditional tube-type television). To enjoy beautiful  
and bright images on your Pioneer Plasma Display System for  
many years to come, please carefully read and follow the usage  
guidelines below.  
• Distance the unit slightly from other equipment, walls, etc.  
For the minimum space required around the unit, see pages  
15 to 16.  
• Do not fit the unit inside narrow spaces where ventilation is  
poor.  
• Do not cover with a cloth, etc.  
• Clean the vents on the sides and rear of the unit to remove  
dust build-up by using a vacuum cleaner set to its lowest  
suction setting.  
Usage guidelines  
All phosphor-based screens (including conventional tube-type  
televisions) can be affected by displaying static images for a  
prolonged period. Plasma Display Systems are no exception to  
this rule. After-image and permanent effects on the screen can  
be avoided by taking some basic precautions. By following the  
recommendations listed below, you can ensure longer and  
satisfactory results from your plasma:  
• Do not place the product on a carpet or blanket.  
• Do not leave the product tilted over except the case of vertical  
installation of the Media Receiver.  
• Do not reverse the product.  
Using the unit without proper ventilation may cause the  
internal temperature to rise, and could result in possible  
malfunction. When the surrounding or internal temperature  
exceeds a certain degree, the display will automatically power  
off in order to cool the internal electronics and prevent a  
hazardous occurrence.  
• Whenever possible, avoid frequently displaying the same  
image or virtually still moving pictures (e.g. closed-captioned  
images or video game images which have static portions).  
• Avoid viewing the On Screen Display for extended periods,  
from a DVD player, VCR, and all other components.  
Malfunction can be caused by many factors: inappropriate  
installation site, improper assembly/installation/mounting,  
improper operation of or modifications made to this product.  
However, PIONEER cannot be held responsible for accidents or  
malfunction caused by the above.  
• Do not leave the same picture freeze-framed or paused  
continuously over a long period of time, when using the still  
picture mode from a TV, VCR, DVD player or any other  
component.  
• Images which have both very bright areas and very dark  
areas side by side should not be displayed for a prolonged  
period of time.  
The following are typical effects and characteristics of a  
phosphor-based matrix display and as such, are not covered by  
the manufacturer’s limited warranties:  
• Permanent residual images upon the phosphors of the panel.  
• The existence of a minute number of inactive light cells.  
• Panel generated sounds, examples: Fan motor noise, and  
electrical circuit humming / glass panel buzzing  
• When playing a game, the “GAME” mode setting within “AV  
Selection” is strongly recommended. However, please limit its  
use to less than 2 hours at a time.  
• After playing a game, or displaying a PC image or any still  
image, it is best to view a normal moving picture in the  
“WIDE” or “FULL” screen setting for over 3 times longer than  
the previous still/moving image.  
• After using the Plasma Display System, always switch the  
display to “STANDBY” mode.  
6
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important User Guidance Information  
01  
Panel sticking and after-image lag  
• Displaying the same images such as still images for a long  
time may cause after-image lagging. This may occur in the  
following two cases.  
1. After-image lagging due to remaining electric  
load  
When image patterns with very high peak luminance are  
displayed more than 1 minute, after-image lagging may occur  
due to the remaining electric load. The after-images remaining  
on the screen will disappear when moving images are  
displayed. The time for the after-images to disappear depends  
on the luminance of the still images and the time they had  
been displayed.  
2. After-image (lag image) due to burning  
Avoid displaying the same image on the Plasma Display  
continuously over a long period of time. If the same image is  
displayed continuously for several hours, or for shorter periods  
of time over several days, a permanent after-image may remain  
on the screen due to burning of the fluorescent materials. Such  
images may become less noticeable if moving images are later  
displayed, but they will not disappear completely.  
• The Energy save function can be set to help prevent damage  
from screen burning (see page 44).  
About operations through i.LINK  
PIONEER shall not always assure normal video/audio recording  
or playback when a D-VHS is operated through i.LINK.  
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART,  
STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY  
FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS  
DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND,  
TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE  
MANUFACTURER, OR SOLD WITH THE PRODUCT. FOLLOW  
THE MANUFACTURE’S INSTRUCTIONS WHEN INSTALLING  
THE PRODUCT AND USE MOUNTING ACCESSORIES  
RECOMMENDED BY THE MANUFACTURER.  
A PRODUCT AND CART COMBINATION SHOULD BE MOVED  
WITH THE CARE. QUICK STOPS, EXCESSIVE FORCE, AND  
UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART  
COMBINATION TO OVERTURN.  
7
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
02 Safety Precautions  
Electricity is used to perform many useful functions, but it can  
also cause personal injuries and property damage if improperly  
handled. This product has been engineered and manufactured  
with the highest priority on safety. However, improper use can  
result in electric shock and/or fire. In order to prevent potential  
danger, please observe the following instructions when install-  
ing, operating and cleaning the product. To ensure your safety  
and prolong the service life of your product, please read the  
following precautions carefully before using the product.  
13. The plasma Display used in this product is made of glass.  
Therefore, it can break when the product is dropped or  
applied with impact. Be careful not to be injured by broken  
glass pieces in case the plasma Display breaks.  
14. Overloading—Do not overload AC outlets or extension  
cords. Overloading can cause fire or electric shock.  
15. Entering of objects and liquids—Never insert an object into  
the product through vents or openings. High voltage flows  
in the product, and inserting an object can cause electric  
shock and/or short internal parts. For the same reason, do  
not spill water or liquid on the product.  
1. Read instructions—All operating instructions must be read  
and understood before the product is operated.  
2. Keep this manual in a safe place—These safety and  
operating instructions must be kept in a safe place for  
future reference.  
3. Observe warnings—All warnings on the product and in the  
instructions must be observed closely.  
16. Servicing—Do not attempt to service the product yourself.  
Removing covers can expose you to high voltage and other  
dangerous conditions. Request a qualified service person to  
perform servicing.  
17. Repair—If any of the following conditions occurs, unplug  
the power cord from the AC outlet, and request a qualified  
service person to perform repairs.  
4. Follow instructions—All operating instructions must be  
followed.  
5. Cleaning—Unplug the power cord from the AC outlet before  
cleaning the product. Use a damp cloth to clean the  
product. Do not use liquid cleaners or aerosol cleaners.  
a. When the power cord or plug is damaged.  
b. When a liquid was spilled on the product or when  
objects have fallen into the product.  
6. Attachments—Do not use attachments not recommended  
by the manufacturer. Use of inadequate attachments can  
result in accidents.  
7. Water and moisture—Do not use the product near water,  
such as bathtub, washbasin, kitchen sink and laundry tub,  
swimming pool and in a wet basement.  
c. When the product has been exposed to rain or water.  
d. When the product does not operate properly as de-  
scribed in the operating instructions.  
Do not touch the controls other than those described in  
the operating instructions. Improper adjustment of  
controls not described in the instructions can cause  
damage, which often requires extensive adjustment work  
by a qualified technician.  
8. Stand—Do not place the product on an unstable cart,  
stand, tripod or table. Placing the product on an unstable  
base can cause the product to fall, resulting in serious  
personal injuries as well as damage to the product. Use  
only a cart, stand, tripod, bracket or table recommended by  
the manufacturer or sold with the product. When mounting  
the product on a wall, be sure to follow the manufacturer’s  
instructions. Use only the mounting hardware  
e. When the product has been dropped or damaged.  
f. When the product displays an abnormal condition. Any  
noticeable abnormality in the product indicates that the  
product needs servicing.  
18. Replacement parts—In case the product needs replace-  
ment parts, make sure that the service person uses  
replacement parts specified by the manufacturer, or those  
with the same characteristics and performance as the  
original parts. Use of unauthorized parts can result in fire,  
electric shock and/or other danger.  
19. Safety checks—Upon completion of service or repair work,  
request the service technician to perform safety checks to  
ensure that the product is in proper operating condition.  
recommended by the manufacturer.  
9. When relocating the product placed on a cart, it must be  
moved with utmost care. Sudden stops, excessive force and  
uneven floor surface can cause the product to fall from the  
cart.  
20. Wall or ceiling mounting—When mounting the product on  
a wall or ceiling, be sure to install the product according to  
the method recommended by the manufacturer.  
21. Heat sources—Keep the product away from heat sources  
such as radiators, heaters, stoves and other heat- generat-  
ing products (including amplifiers).  
22. Unplug the power cord from the AC outlet before installing  
the speakers.  
23. Never expose the screen of the Plasma Display to a strong  
impact, for example, by hitting it. The screen may be  
broken, resulting in fire or personal injury.  
24. Do not expose the Plasma Display to direct sunlight for a  
long period of time. The optical characteristics of the front  
protection panel changes, resulting in discoloration or  
warp.  
10. Ventilation—The vents and other openings in the cabinet  
are designed for ventilation. Do not cover or block these  
vents and openings since insufficient ventilation can cause  
overheating and/or shorten the life of the product. Do not  
place the product on a bed, sofa, rug or other similar  
surface, since they can block ventilation openings. This  
product is not designed for built-in installation; do not place  
the product in an enclosed place such as a bookcase or  
rack, unless proper ventilation is provided or the  
manufacturer’s instructions are followed.  
11. Power source—This product must operate on a power  
source specified on the specification label. If you are not  
sure of the type of power supply used in your home, consult  
your dealer or local power company.  
12. Power cord protection—The power cords must be routed  
properly to prevent people from stepping on them or objects  
from resting on them. Check the cords at the plugs and  
product.  
25. The Plasma Display weighs about 32.8 kg (72.3 lbs.) for the  
PRO-505PU and about 26.8 kg (59.1 lbs.) for the PRO-  
435PU. Because it has small depth and is unstable, unpack,  
carry, and install the product with one more person at least  
and use the handles.  
8
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Precautions  
02  
Installation Precautions  
Observe the following precautions when installing with any items such as the optional stand.  
When using the optional stand, brackets, or equivalent items  
• Ask your dealer to perform the installation.  
• Be sure to use the supplied bolts.  
• For details, see the instruction manual that comes with the optional stand (or equivalent items).  
When using other items  
• Consult your dealer.  
• The following six mounting holes can be used for the installation:  
Side view  
Mounting surface  
Rear view  
Mounting  
Plasma  
Display  
bracket (or  
equivalent item)  
Mounting hole  
Mounting hole  
Median line  
M8 screw  
12 to 18 mm  
(0.5 to 0.7 inches)  
Median line  
• Be sure to use four or more mounting holes symmetrical to the vertical and horizontal median lines.  
• Use M8 screws, which go 12 to 18 mm (0.5 to 0.7 inches) in depth from the mounting surface of the Plasma Display. See the side  
view above.  
• Be careful not to block the ventilation opening at the rear of the Plasma Display.  
• Be sure to install the Plasma Display on a flat surface because it contains glass.  
• The screw holes other than the above are to be used only for the specified products. Never use them for mounting non-specified  
products.  
• Do not mount or remove the Plasma Display to or from the stand, with speakers attached.  
• It is strongly recommended to use the optional PIONEER mounting products.  
• PIONEER shall not be liable for any personal injury or product damage that results from the use of mounting items other than the  
optional PIONEER products.  
9
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03 Operational Precautions  
Condensation  
• Condensation may take place on the surface or inside of the  
product when the product is rapidly moved from a cold place  
to a warm place or just after a heater is switched on in winter  
morning, for example. When condensation takes place, do  
not switch on the product and wait until condensation  
disappears. Using the product with condensation may result  
in malfunction.  
PIONEER bears no responsibility for any damages arising from  
incorrect use of the product by you or other people,  
malfunctions when in use, other product related problems, and  
use of the product except in cases where the company must be  
liable.  
Plasma Display protection function  
When still images (such as photos and computer images) stay  
on the screen for an extended period of time, the screen will be  
slightly dimmed. This is because the protection function of the  
Plasma Display automatically adjusts the brightness to protect  
the screen when detecting still images; so this does not  
designate malfunction. The screen is dimmed when a still  
image is detected for about three minutes.  
Cleaning the screen  
• When cleaning the screen of this product, gently wipe it with  
a soft dry cloth; the supplied cleaning cloth or other similar  
cloths (e.g., cotton and flannel). If you use a hard cloth or rub  
the screen hard, the surface of the screen will be scratched.  
• If you clean the surface of the screen with a wet cloth, water  
droplets on the surface may enter into the product, resulting  
in malfunction.  
Infrared rays  
The Plasma Display releases infrared rays because of its  
characteristics. Depending on how the Plasma Display is in  
use, the remote controls of nearby equipment may be adversely  
affected or wireless headphones using infrared rays are  
interfered by noise. If this is the case, place that equipment at a  
location where its remote control sensor is not affected.  
Cleaning the cabinet  
• When cleaning the cabinet of this product, gently wipe it with  
a soft dry cloth; the supplied cleaning cloth or other similar  
cloths (e.g., cotton and flannel). If you use a hard cloth or rub  
the cabinet hard, the surface of the cabinet will be scratched.  
• The cabinet of this product is mostly composed of plastic. Do  
not use chemicals such as benzine or thinner to clean the  
cabinet. Using these chemicals may result in quality deterio-  
ration or coating removal.  
Radio interference  
While this product meets the required specifications, it emits a  
small amount of noise. If you place such equipment as an AM  
radio, personal computer, and VCR close to this product, that  
equipment may be interfered. If this happens, place that  
equipment far enough from this product.  
• Do not expose the product to volatile gas or fluid such as  
pesticide. Do not make the product contact with rubber or  
vinyl products for a long period of time. The effect of  
plasticizer in the plastic may result in quality deterioration or  
coating removal.  
Fan motor noise  
When ambient temperature of the Media Receiver becomes  
high, the rotation speed of the cooling fan motor increases.  
This may make you feel that the fan motor is noisy at such an  
occasion.  
• If you clean the surface of the cabinet with a wet cloth, water  
droplets on the surface may enter into the product, resulting  
in malfunction.  
The fan motor keeps running until the power cord of the Media  
Receiver is removed from a wall outlet.  
Handles at the rear of the Plasma Display  
• Do not remove the handles from the rear of the Plasma  
Display.  
Do not attach such items as labels and tape to the  
product.  
• This may result in the discoloration or scratch of the cabinet.  
• When moving the Plasma Display, ask another person for  
help and use the handles attached to the rear of the Plasma  
Display. Do not move the Plasma Display by holding only a  
single handle. Use the handles as shown.  
When not using the product for a long period of time  
• If you do not use the product for a long period of time, the  
functions of the product may be adversely affected. Switch on  
and run the product occasionally.  
• Do not use the handles to hang the product when installing  
or carrying the product, for example. Do not use the handles  
for the purpose of preventing the product from tilting over.  
10  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Supplied Accessories  
04  
Plasma Display  
Cleaning cloth  
Speed clamp × 3  
Power cord (2 m/6.6 feet)  
Bead band × 3  
Warranty card  
Media Receiver  
Power cord (2 m/6.6 feet)  
Remote control unit  
System cable (3 m/9.8 feet)  
Screw × 4  
(for stand)  
AA size battery × 2  
(Alkaline battery)  
Stand  
VCR controller  
(1.8 m/5.9 feet)  
Screw hole cap × 4  
Operating Instructions  
Instruction guide  
• Always use the power cord supplied with the Plasma Display and the  
one supplied with the Media Receiver for each respective unit.  
11  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
05  
Part Names  
Plasma Display  
Front view  
(right view)  
1
2
button  
STANDBY indicator  
Lights red when the unit is standby mode.  
(page 24)  
5
6
3
POWER ON indicator  
Lights green when the Plasma Display is  
operating. (page 24)  
7
8
4
5
6
7
8
Remote control sensor  
STANDBY/ON button  
INPUT button  
4
VOLUME +/– buttons  
CHANNEL +/– buttons  
Rear view  
9
SYSTEM CABLE terminal (BLACK)  
10 SYSTEM CABLE terminal (WHITE)  
11 SPEAKER (right/left) terminals  
12 AC INLET terminal  
9
11  
12  
10  
The terminals have faced downward.  
Media Receiver  
Front view  
1
2
3
4
5
6
POWER button  
POWER  
REC  
TIMER  
DATA  
ACQUISITION  
POWER ON indicator  
STANDBY indicator  
REC TIMER indicator  
DATA ACQUISITION indicator  
ON  
STANDBY  
Pull this section to open the door.  
1
2 3 4 5  
INPUT 4 terminals  
(COMPONENT VIDEO: Y, CB/PB, CR/PR)  
7
8
9
INPUT 4 terminal (S-VIDEO)  
INPUT 4 terminal (VIDEO)  
INPUT 4 terminals (AUDIO)  
INPUT  
4
PC  
AUDIO  
(STEREO)  
COMPONENT VIDEO  
S-  
VIDEO  
VIDEO  
AUDIO  
ANALOG RGB  
Y
C
B
/
P
B
C
R
/
P
R
L
R
10 PC INPUT terminal (AUDIO)  
11 PC INPUT terminal (ANALOG RGB)  
6
7
8 9 10 11  
12  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names  
05  
Rear view  
1
2
3 4  
5
6
7 8  
9
10  
11  
12  
13  
DIGITAL OUT  
OPTICAL  
I N  
CONTROL  
OUT  
VCR CONTROL  
ANTENNA/  
CABLE A IN  
Cable  
CARD  
IN  
ANTENNA B  
S400  
(TS)  
AC IN  
INPUT 2  
R-AUDIO-L  
INPUT 1  
S-VIDEO INPUT  
2
INPUT  
1
COMPONENT VIDEO  
Y
VIDEO  
VIDEO  
R-AUDIO-L  
C
B
/P  
B
C
R
/P  
R
BLACK  
SERVICE ONLY  
OUT  
INPUT 1  
INPUT 3  
WHITE  
SYSTEM CABLE  
HDMI  
MONITOR OUT  
VIDEO  
R-AUDIO-L  
R-AUDIO-L  
INPUT 3  
INPUT  
Y
C
B
/P  
B
C
R
/P  
R
S-VIDEO  
S-VIDEO  
3
24  
25  
26  
14  
1516 17 18 19 20 21  
22  
23  
1
2
3
4
5
6
7
8
9
CONTROL IN terminal  
CONTROL OUT terminal  
VCR CONTROL terminal  
ANTENNA B IN terminal  
ANTENNA/CABLE A IN terminal  
INPUT 2 terminal (VIDEO)  
INPUT 2 terminals (AUDIO)  
i.LINK terminals  
14 RS-232C terminal (used for factory setup)  
15 ANTENNA B OUT terminal  
16 INPUT 2 terminal (S-VIDEO)  
17 MONITOR OUT terminal (S-VIDEO)  
18 MONITOR OUT terminal (VIDEO)  
19 MONITOR OUT terminals (AUDIO)  
20 INPUT 1 terminal (VIDEO)  
21 INPUT 1 terminal (S-VIDEO)  
Cable CARD slot  
22 INPUT 3 terminals (AUDIO)  
10 INPUT 1 terminals (AUDIO)  
11 DIGITAL OUT terminal (OPTICAL)  
12 INPUT 1 terminals  
23 INPUT 3 terminals  
(COMPONENT VIDEO: Y, CB/PB, CR/PR)  
24 HDMI terminals (INPUT1/INPUT3)  
25 SYSTEM CABLE terminal (WHITE)  
26 SYSTEM CABLE terminal (BLACK)  
(COMPONENT VIDEO: Y, CB/PB, CR/PR)  
13 AC IN terminal  
13  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
05  
Part Names  
6 CH +/–: Selects the channel.  
7 RETURN: Returns to the previous menu  
Remote control unit  
Mode switch (with  
“TV” selected)  
screen.  
1
2
8
/ / / : Selects a desired item on the menu  
screen.  
9 DTV INFO: Shows more information on DTV  
programs.  
14  
10 SPLIT: Switches the screen mode among 2-  
screen, picture-in-picture, and single-screen.  
3
15  
16  
11 FREEZE: Freezes a frame from a moving  
image. Press again to cancel the function.  
12 SWAP: Switches between the two screens  
when in the 2-screen or picture-in-picture  
mode.  
17  
4
5
18  
19  
13 SHIFT: Moves the location of the small screen  
when in the picture-in-picture mode.  
6
14 :When pressed, all buttons on the remote  
control unit will light. The lighting will turn  
off if no operations are performed within  
about 5 seconds. This button is used for  
performing operations in dark places.  
20  
21  
7
8
9
22  
15 ANT: Selects the antenna (A, B). See pages 21  
and 22 for details.  
23  
16 MTS: Selects the MTS/SAP.  
17 0 – 9: Selects the channel.  
10  
11  
12  
13  
24  
25  
26  
18 CH ENTER: Executes a channel number.  
19 VOL +/–: Sets the volume.  
27  
20  
MUTING: Mutes the sound.  
21 HOME MENU: Displays the menu screen.  
22 ENTER: Executes a command.  
23 FAVORITE CH (A, B, C, D):  
Selects any of the four preset channels. See  
page 37 for details to set the FAVORITE CH.  
While watching, you can toggle the set chan-  
nels by pressing A, B, C and D.  
24 SCREEN SIZE: Selects the screen size.  
With the mode switch set to TV  
25 DISPLAY: Displays the channel information.  
1 TV : Turns on the power to the Plasma  
26 AV SELECTION: Selects audio and video  
settings. (AV mode: STANDARD, DYNAMIC,  
MOVIE, GAME, USER. PC mode: STANDARD,  
USER.)  
Display or places it into standby mode.  
2 Transmission confirmation LED  
3 INPUT: Selects an input source of the Plasma  
Display. (INPUT 1, INPUT 2, INPUT 3, INPUT 4,  
PC, i.LINK)  
27 SLEEP: Sets the sleep timer.  
4 •(dot): Enters a dot.  
• When using the remote control unit, point it at the Plasma Display.  
• See pages 62 to 68 for operating buttons not listed on this page.  
5 CH RETURN: Returns to the previous chan-  
nel.  
14  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparation  
06  
Using the optional PIONEER stand  
For details on installation, refer to the instruction manual  
supplied with the stand.  
Installing the Plasma Display  
• This product may be used only with model PDK-1012 stand.  
Use with other stands may result in instability causing  
possible injury.  
Over 50 cm (19 11  
/16 inches)  
Using the optional PIONEER speakers  
For details on installation, refer to the instruction manual  
supplied with the speaker.  
Operating Environment  
Over 10  
Operating environment temperature and humidity: +0°C to  
+40°C (+32°F to +104°F); less than 85% RH (cooling vents not  
blocked)  
cm (3 15  
/
inches )16  
Avoid installing at the following locations:  
• Under direct exposure to sunlight  
• Under strong artificial light  
• In high humidity  
• Poorly ventilated  
Locating  
• Avoid direct sunlight. Maintain adequate ventilation.  
• The length of the system cable used to connect the Plasma  
Display and the Media Receiver is about 3 m (9.8 feet).  
• Because the Plasma Display is heavy, be sure to have  
someone help you when moving it.  
• If you place anything on the top of the Media Receiver it will  
not receive enough ventilation and will not operate properly.  
• Allow enough space around the upper and back parts when  
installing to ensure ventilation around the backside.  
15  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
06  
Preparation  
Installing the Media Receiver vertically  
You can use the supplied stand to install the Media Receiver  
vertically.  
Installing the Media Receiver  
Plasma Display  
1. Insert the stand into the side of the Media  
Receiver.  
Media Receiver  
(vertical installation)  
(horizontal installation)  
Right side  
POWER  
REC  
DATA  
ON  
STANDBY  
TIMER  
ACQUISITION  
System cable (approx. 3 m/9.8 feet)  
• Do not place a VCR or any other device on the top of the  
Media Receiver.  
• When installing, allow enough space on the sides and  
above the Media Receiver.  
• Do not block the side cooling vents or the rear ventila-  
tion fan opening of the Media Receiver.  
2. Secure the stand with the supplied screws.  
Screws  
Over 5 cm  
(2 inches)  
POWER  
REC  
DATA  
ON  
STANDBY  
TIMER  
ACQUISITION  
Over 5 cm  
(2 inches)  
Over 5 cm  
(2 inches)  
Over 10 cm  
(3 15/16 inches)  
Over 10 cm  
(3 15/16 inches)  
Over 5 cm  
(2 inches)  
Over 5 cm Over 5 cm  
(2 inches) (2 inches)  
16  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparation  
06  
3. Remove the shock absorbing pads.  
Shock absorbing pad  
Keep the shock absorbing pads and screws. They are required  
when you place the Media Receiver in the horizontal position.  
4. Plug the screw holes using the supplied caps.  
Remove the separation sheet.  
Align with the  
hole and attach.  
Screw hole cap  
• When you have installed the Media Receiver vertically,  
be sure to use the supplied stand. If you place the unit  
directly on the floor, the cooling vents will be blocked,  
resulting in mechanical failure.  
17  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
06  
Preparation  
Connecting the system cable  
Connecting the system cable to the Plasma Display  
Plasma Display (rear view)  
For details on optional PIONEER speaker  
installation, refer to the instruction manual  
that came with the speaker.  
(WHITE)  
(BLACK)  
System cable  
Connecting the system cable to the Media Receiver  
Media Receiver (rear view)  
DIGITAL OUT  
OPTICAL  
I
N
OUT  
CONTROL  
ANTENNA  
VCR CONTROL  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
IN  
B
(BLACK)  
S400  
(TS)  
AC IN  
S-VIDEO INPUT  
2
INPUT  
1
COMPONENT VIDEO  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
BLACK  
SERVICE ONLY  
OUT  
INPUT  
1
INPUT  
3
WHITE  
SYSTEM CABLE  
MONITOR OUT  
VIDEO  
R-AUDIO-L  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
HDMI  
S-VIDEO  
S-VIDEO  
INPUT  
INPUT  
3
3
(WHITE)  
• THESE SPEAKER TERMINALS CAN BE APPLIED WITH HAZARDOUS VOLTAGE WHEN YOU CONNECT OR DIS-  
CONNECT THE SPEAKER CABLES. TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT TOUCH  
UNINSULATED PARTS BEFORE DISCONNECTING THE POWER CORD.  
18  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparation  
06  
Routing cables  
Speed clamps and bead bands are supplied for bunching cables. Once properly bunched, follow the steps below to route the  
cables.  
(rear view)  
When the speakers are installed on the sides  
Speaker cable  
Cable binders (supplied  
with the stand)*  
Speed clamps  
Speaker cable  
*Cable binder  
Using the cable binders supplied with the stand, put the  
speaker and system cables together so that the cables are  
invisible from the front. At that time be careful not to apply  
any force to the connection sections of the cables.  
Attaching and removing speed clamps  
Attaching speed clamps to the main unit  
Attach the speed clamps using the 4 holes marked with  
below, depending on your routing system.  
Insert [1] into an appropriate hole on the rear of the Plasma  
Display and snap [2] into the back of [1] to lock the clamp.  
Speed clamps are designed to be difficult to undo once in  
place. Please attach them carefully.  
Use pliers to twist the clamp 90°, pulling outward. The clamp  
may deteriorate over time and become damaged if removed.  
2
1
19  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
06  
Preparation  
Allowed operation range of the remote control  
unit  
Preparing the remote control unit  
Operate the remote control unit while pointing it toward the  
remote control sensor located at the bottom right of the front  
panel of the Plasma Display. The distance from the remote  
control sensor must be within 7 m (23 feet) and the angle  
relative to the sensor must be within 30 degrees in the right or  
left direction.  
Inserting batteries  
Open the battery cover.  
1
Insert the supplied two AA size batteries.  
2
30°  
• The battery polarities must correspond with the (+) and  
(–) indicators in the battery compartment.  
Remote control  
sensor  
30°  
Close the battery cover.  
3
Cautions regarding the remote control unit  
• Do not expose the remote control unit to shock, liquid, or  
high humidity.  
Cautions regarding batteries  
• The remote control unit cannot operate the system if the  
batteries in the unit are empty. When this happens, replace  
the batteries with new ones.  
• Do not place the remote control unit under direct sunlight;  
the unit may deform.  
• Do not use manganese batteries. When you replace the  
batteries, use alkaline ones.  
• The remote control unit may not work properly if the remote  
sensor window of the Plasma Display is under direct sunlight  
or strong lighting. In such case, change the angle of the  
lighting or Plasma Display, or operate the remote control unit  
closer to the remote sensor window.  
• Do not mix batteries of different types. Different types of  
batteries have different characteristics.  
• Do not mix old and new batteries. Mixing old and new  
batteries can shorten the life of new batteries or cause  
chemical leakage in old batteries.  
• When any obstacle exists between the remote control unit  
and the remote control sensor, the remote control unit may  
not function.  
• Do not leave dead batteries in the remote control unit;  
chemical leakage will occur. If you find any chemical leakage,  
wipe thoroughly with a cloth.  
• As the batteries become empty, the remote control unit can  
function within a shorter distance from the remote control  
sensor. Replace the batteries with new ones if necessary.  
• The batteries supplied with this product may have a shorter  
life expectancy due to storage conditions.  
• The Plasma Display emits very weak infrared rays from its  
screen. If you place such equipment operated through  
infrared remote control as a VCR nearby, that equipment may  
not receive commands from its remote control unit properly  
or entirely. If this is the case, place that equipment at a  
location far enough from the Plasma Display.  
• If you will not use the remote control unit for an extended  
period of time, remove the batteries from it.  
• WHEN DISPOSING OF USED BATTERIES, BE SURE  
TO COMPLY WITH GOVERNMENT REGULATIONS  
AND ENVIRONMENTAL PROTECTION GUIDELINES  
THAT APPLY IN YOUR COUNTRY OR AREA.  
• Depending on the installation environment, infrared rays  
from the Plasma Display may not allow this system to  
properly receive commands from the remote control unit or  
may shorten allowable distances between the remote control  
unit and the remote control sensor. The strength of infrared  
rays emitted from the screen differs, depending on images  
displayed on the screen.  
20  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparation  
06  
Cable connections for watching digital  
and/or conventional TV channels  
Cable connections for watching digital  
TV channels over air (VHF/UHF)  
This system is equipped with two terminals for inputting TV  
broadcasting signals: ANTENNA/CABLE A IN and ANTENNA B.  
The ANTENNA/CABLE A IN terminal accepts both digital and  
conventional TV broadcasting signals while the ANTENNA B  
terminal accepts only conventional TV broadcasting signals.  
When using a cable TV to watch digital and/or conventional TV  
channels, connect to the ANTENNA/CABLE A IN terminal as  
shown. In addition, you may connect an antenna to the  
ANTENNA B terminal as shown; use an outdoor antenna to  
enjoy clearer pictures. If your outdoor uses a 75-ohm coaxial  
cable with an F-type connector, plug it into the antenna  
terminal at the rear of the Media Receiver.  
If using VHF and UHF antennas to watch digital TV channels,  
connect the coaxial cables as shown.  
Connecting VHF/UHF antennas  
VHF antenna  
UHF antenna  
U/V mixer  
Connecting VHF/UHF antennas and a Cable  
Converter  
Media Receiver (rear)  
ANTENNA/  
CABLE A IN  
Splitter  
Splitter  
Cable TV  
Cable Converter  
ANTENNA B  
IN  
ANTENNA/  
CABLE A IN  
Media Receiver  
(rear)  
IN  
ANTENNA B  
OUT  
Media Receiver (rear)  
• Be sure to connect coaxial cables as shown above. Signal reception  
may fail if not properly connected.  
OUT  
• Be sure to connect coaxial cables as shown above. Signal reception  
may fail if not properly connected.  
21  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
06  
Preparation  
Insert the specified cable card into the Cable CARD slot  
as far as it goes.  
3
Switching between antenna A and B  
To watch broadcasts via the two antennas, you can select it by  
pressing ANT on the remote control unit.  
• While watching a broadcast, press ANT to view the image  
received from the other antenna.  
AL OUT  
DIGIT  
• Pressing ANT while watching in the 2-screen mode (TV  
image and video image) with TV selected will display the TV  
image of the other antenna.  
OPTICAL  
le  
Cab  
CARD  
VIDEO  
R
• Pressing ANT while watching in the 2-screen mode with two  
TV images displayed will not have any effect.  
/P  
R
C
T  
(TS)  
ANTENNA/  
CABLE A IN  
• Pressing ANT while watching in the 2-screen mode with two  
video images displayed will switch the selected screen to a  
TV image.  
VIDEO  
INPUT 1  
H
R-AUDIO-
R
PUT  
2
N
/P  
R
C
VIDEO  
B
/P  
B
C
Y
INPUT 3  
R-AUDIO-L  
S-VIDEO  
R-AUDIO-L  
DEO  
VI  
Inserting the cable card  
The Media Receiver is equipped with a slot for inserting a cable  
card. When you are watching digital and/or High Definition TV  
channels over cable, the card allows you to use the POD  
service provided by the cable TV company; the POD stands for  
Point of Deployment. This service presents various types of  
useful information, using HTML text.  
• Be sure to insert only the specified cable card.  
• Do not insert a PCMCIA card.  
Confirm that the ANTENNA/CABLE A IN terminal has  
been connected with the coaxial cable from the Cable  
Converter. See page 21.  
1
Hold the tab of the slot cover on the rear of the Media  
Receiver, and remove the cover while releasing the tab’s  
latch.  
2
Tab  
AL OUT  
DIGIT  
OPTICAL  
le  
Cab  
CARD  
VIDEO  
R
/P  
R
S400  
C
B
COMPONENT  
/P  
B
C
(TS)  
INPUT 1  
Y
R-AUDIO
INPUT 1  
VIDEO  
UDIO-L  
A
R
P
/
R
C
22  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparation  
06  
Connecting the power cord  
Connect the power cord after all component connections have been completed.  
Plasma Display (rear view)  
Power cord  
Noise filter  
Partially eliminates noise  
caused by the power source.  
Media Receiver (rear view)  
DIGITAL OUT  
OPTICAL  
I
N
OUT  
CONTROL  
ANTENNA  
VCR CONTROL  
ANTENNA/  
Cable  
CARD  
CABLE  
A
IN  
IN  
B
S400  
(TS)  
ACIN
INPUT  
2
S-VIDEO INPUT  
2
INPUT  
1
COMPONENT VIDEO  
Y CB/PB CR/PR  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
AC IN  
BLACK  
SERVICE ONLY  
OUT  
INPUT  
1
INPUT  
3
WHITE  
SYSTEM CABLE  
MONITOR OUT S-VIDEO  
VIDEO  
R-AUDIO-L  
R-AUDIO-L INPUT  
INPUT  
3
Y
CB/PB  
CR/PR  
HDMI  
S-VIDEO  
3
INPUT  
3
Power cord  
Noise filter  
Partially eliminates noise  
caused by the power source.  
• Always turn off the power of the Plasma Display and Media Receiver  
when connecting the power cords.  
• Disconnect the power cord from the power outlet when the Plasma  
Display System is not going to be used for a long period of time.  
• Use only the supplied power cord.  
• Be sure to use the specified power supply voltage;  
neglecting this can result in fire or electric shock.  
• For the Plasma Display System, a three-core power cord  
with a ground terminal is used for efficiency protection.  
Always connect the power cord to a three-pronged  
outlet and make sure that the cord is properly grounded.  
23  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
07  
Basic Operations  
Plasma Display  
Turning on the power (Standby)  
1
Press on the Plasma Display if the STANDBY indicator  
is off.  
• The STANDBY indicator on the Plasma Display lights  
up red.  
Confirm that the STANDBY indicators light up red, and  
then press TV on the remote control unit or  
STANDBY/ON on the Plasma Display or POWER on the  
Media Receiver to turn the system on.  
2
STANDBY indicator  
POWER ON indicator  
• The POWER ON indicators on the Plasma Display and  
Media Receiver light up green.  
button  
(right view)  
• In this manual, “system” means the Plasma Display Panel and Media  
Receiver.  
STANDBY/  
ON button  
Turning off the power (Standby)  
1
Press TV on the remote control unit or STANDBY/ON  
on the Plasma Display or POWER on the Media Receiver.  
• The system enters the standby mode and the image on  
the screen disappears.  
• Both STANDBY indicators light up red.  
• It is recommended to place the system into the standby  
mode by pressing TV on the remote control unit.  
This allows the system to automatically receive digital  
TV program information in the standby mode.  
Media Receiver  
POWER  
• If you are not going to use this system for a long period of time, press  
on the Plasma Display and remove the power cord from the power  
outlet.  
REC  
TIMER  
DATA  
ACQUISITION  
ON  
STANDBY  
STANDBY indicator  
POWER ON indicator  
POWER button  
Plasma Display/Media Receiver status indicators  
Indicator Status  
System Status  
Plasma Display  
Media Receiver  
POWER ON  
STANDBY  
POWER ON  
STANDBY  
Power to the Plasma Display and Media Receiver is off. Or the power cords  
have been disconnected.  
Power to the system is on.  
The system is in the standby mode.  
The power cord has been disconnected from the Media Receiver.  
Flashing  
Power to the Plasma Display is off. Or the power cord has been disconnected  
from the Plasma Display.  
Flashing  
For other than the above, see “Troubleshooting” on page 69.  
24  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
07  
Plasma Display  
(right view)  
Watching TV channels  
Unless you set up TV channels that you can watch under the  
current conditions, you cannot tune in those channels. For the  
procedure, see “Setting up TV channels” on page 31.  
CHANNEL +/–  
• When watching a digital TV program, you may see emergency alert  
messages scrolling at the top of the screen. Those messages are  
broadcasted by TV stations as necessary when in emergency  
situations.  
Selecting the antenna  
After confirming that the Mode switch on the remote control  
unit has been set to “TV”, press ANT on the remote control unit  
to select antenna A or B.  
• Make this selection depending on the connections to the  
antenna input terminals on the Media Receiver (page 21).  
Changing channels  
To increase the channel number, press CH + on the remote  
control unit. To decrease the channel number, press CH –.  
• CHANNEL +/– on the Plasma Display operates the same as  
CH +/– on the remote control unit.  
• Press CH RETURN to switch the currently tuned channel to  
the previously tuned channel.  
Press CH RETURN again to restore the currently tuned  
channel.  
Using 0 – 9 and • (dot) on the remote control unit  
Select channels directly by pressing buttons 0 to 9. To select  
subchannels, also use the • (dot) button.  
EXAMPLE  
• To select channel 5 (1-digit channel), press 5.  
• To select channel 25 (2-digit channel), press 2 then 5.  
• To select channel 125 (3-digit channel), press 1, 2, then 5.  
• To select subchannel 10.01, press 1, 0, • (dot), 0, then 1.  
Channel banner  
12:33pm  
• To select subchannel 10.001 (for the cable TV), press 1, 0,  
• (dot), 0, 0, then 1.  
DTV 2 • 1002.102 A  
XXXXXXXXXX  
12:30pm — 2:00pm  
• After entering a channel or subchannel number, you may press  
CH ENTER to tune in the channel more quickly.  
• Each time you change a channel, such a channel banner appears  
that shows information about the currently selected channel. To clear  
the channel banner, press DTV INFO. For more information about  
the channel banner, see “Viewing a channel banner” on page 26.  
25  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
07  
Basic Operations  
Changing the volume and sound  
Viewing a channel banner  
While watching a digital TV program, pressing DTV INFO  
causes the following banner to appear. Pressing DTV INFO  
again causes the banner to disappear.  
To increase the volume, press VOL + on the remote control  
unit. To decrease the volume, press VOL –.  
• VOLUME +/– on the Plasma Display operates the same as  
VOL +/– on the remote control unit.  
• To mute the sound output, press MUTING. “ ” appears on  
the screen. To quit muting, press MUTING again. Pressing  
VOL + also quits muting.  
Plasma Display  
(right view)  
1
2
3
4
VOLUME +/–  
12:33pm  
WXCD • 1000 Ant. A  
XXXXXXXXXX  
********************************************************  
*********************************************  
******************************************  
12:30pm – 2:00pm  
5
6
7
1
2
3
4
5
6
7
Station name  
Current time  
Channel number  
Input (Ant. A or Ant. B)  
Program time schedule  
Program title  
TV rating and program description (This may be unavailable  
for some programs.)  
Volume adjustment  
Muting  
• The above information is not displayed if not included in broadcast  
signals.  
• If “ ” is shown at the bottom right of the channel banner containing  
program description, press  
/
to scroll the program description.  
26  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
07  
Using the POD service  
Setting MTS/SAP mode  
If you have watched digital and/or High Definition TV channels  
over cable, you can use the POD service provided by the cable  
TV company. This service presents various types of useful  
information, using HTML text.  
When watching conventional TV programs, you may enjoy  
stereo sound and/or Secondary Audio Programs (SAP), using  
the Multi-channel Television Sound (MTS) function.  
• Stereo broadcasts  
You can enjoy, for example, sports, shows, and concerts in  
dynamic stereo sound.  
• SAP broadcasts  
MAIN sound: The normal program soundtrack (either in  
mono or stereo).  
SAP sound: Listen to second language, supplementary  
commentary and other information. (SAP is mono sound.)  
• Conventional TV channels in this manual designate TV channels that  
are received through the conventional VHF/UHF frequencies or  
conventional cable TV channels.  
Press HOME MENU, 9, 9, then 9 to view the POD display.  
• When stereo sound is difficult to hear, you may manually switch to  
the MONO mode to obtain clearer sound.  
• Once the MONO mode is selected, the Plasma Display System  
sound remains mono even if the system receives a stereo broadcast.  
You must reselect the STEREO mode if you want to hear stereo  
sound again.  
• If you have enabled data acquisition using the menu, POD  
information is automatically acquired even when the system is in the  
standby mode. See page 32.  
• Selecting MTS while the input source is INPUT 1 to 4 or PC does not  
change the type of sound. In this case, sound is determined by the  
video source.  
Changing the language  
If you have selected a digital TV program that provides multi-  
language services, you can switch among the languages by  
pressing MTS on the remote control unit.  
Each time you press MTS, MTS toggles as shown below.  
Each time you press MTS, the language switches.  
STEREO mode  
SAP mode  
MONO mode  
• Switchable languages differ depending on the current broadcast.  
• If the language selected through language setting is available when  
the channel or program is changed, you will hear that language.  
STEREO  
SAP  
MONO  
• In each of the MTS/SAP modes selected using the MTS button, the  
display changes depending on broadcasting signals being received.  
27  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
07  
Basic Operations  
When receiving STEREO sound signals  
Using the multiscreen functions  
A
125  
STEREO  
In STEREO mode  
In SAP mode  
Splitting the screen  
Use the following procedure to select the 2-screen or picture-in-  
picture mode.  
A
125  
2-screen  
STEREO  
A
125  
MONO  
In MONO mode  
When receiving MAIN + SAP sound signals  
A
125  
Picture-in-picture  
MAIN (SAP)  
In STEREO mode  
A
125  
SAP (MAIN)  
In SAP mode  
A
125  
MONO (SAP)  
In MONO mode  
When receiving STEREO + SAP sound signals  
A
125  
STEREO (SAP)  
In STEREO mode  
A
125  
SAP (STEREO)  
In SAP mode  
A
125  
MONO (SAP)  
In MONO mode  
Press SPLIT to select the display mode.  
• Each time you press SPLIT, the display mode is  
switched among 2-screen, picture-in-picture, and  
single-screen.  
1
When receiving MONO sound signals  
A
125  
MONO  
In STEREO mode  
A
125  
MONO  
In SAP mode  
A
125  
MONO  
In MONO mode  
28  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
07  
• In 2-screen or picture-in-picture mode, press SWAP to  
switch the position of the 2 screens shown.  
Left screen is the active screen which will be indicated  
by “ ”. The user is allowed to operate picture and  
sound.  
Freezing images  
Use the following procedure to capture and freeze one frame  
from a moving image that you are watching.  
Normal image  
Still image  
• In 2-screen mode, press SCREEN SIZE to change the  
size of the left screen.  
• In picture-in-picture mode, press SHIFT to move the  
position of the small screen in anti-clockwise.  
Press FREEZE.  
• A still image appears on the right screen while a  
moving image is shown on the left screen.  
1
2
Press FREEZE again to cancel the function.  
• With the screen split, any image cannot be frozen.  
• When this function is not available, a warning message appears.  
To select the desired input source, press the appropriate  
input source button.  
2
• If watching TV programs, press CH +/– to change the  
channel.  
• The multiscreen function cannot display images from the same input  
source at the same time. If you make such an attempt, a warning  
message appears.  
• When you press HOME MENU or DTV INFO, the single-screen  
mode is restored and the corresponding menu is displayed.  
• When the two screens show the same analog broadcasting coming  
through antenna A and B, the picture quality may differ between the  
two screens.  
29  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
08  
Menu Setup  
PC mode menus  
Menu configuration  
Home Menu  
Item  
Page  
Picture  
AV Selection  
Contrast  
40  
41  
AV mode menus  
Home Menu  
Item  
Page  
Brightness  
Red  
41  
41  
41  
41  
41  
Picture  
AV Selection  
Contrast  
40  
41  
41  
Green  
Blue  
Brightness  
Reset  
Color  
41  
Tint  
41  
41  
41  
41  
Sharpness  
Pro Adjust  
Reset  
Sound  
Treble  
43  
43  
Bass  
Balance  
43  
Reset  
43  
43  
43  
FOCUS  
Sound  
Treble  
43  
Front Surround  
Bass  
43  
Balance  
43  
43  
43  
43  
Reset  
Power Control  
Energy Save  
44  
44  
FOCUS  
Power Management  
Front Surround  
Sleep Timer  
—
40  
Power Control  
Energy Save  
44  
44  
44  
No Signal off  
No Operation off  
Option  
Auto Setup  
45  
45  
Manual Setup  
Sleep Timer  
—
40  
Option  
Position  
45  
Menu operations  
Side Mask  
HDMI Input  
Monitor Out  
47  
The following describes the typical procedure for setting up the  
menus. For the actual procedures, see the appropriate pages  
that describe individual functions.  
51, 52  
52, 53  
Digital Audio Out  
54  
Language  
47  
Tuner Setup  
Timers  
Channel Setup  
31, 32  
Parental Control  
33–37  
Favorites  
37  
Closed Captions  
Recorder Setup  
Clock  
37–39  
56–57  
39  
Press HOME MENU.  
1
2
3
Press  
/
to select a menu item, and then press ENTER.  
—
48, 49  
Repeat step 2 until you access the desired submenu item.  
• The number of menu layers differs depending on menu  
items.  
• If you select “Tuner Setup” or “Timers” , a menu bar  
appears at the bottom of the screen. To select a  
submenu item on the bar, press  
/
instead of  
/
.
4
5
Press to select an option (or parameter), and then  
press ENTER.  
/
• For some menu items, press  
/
instead of / .  
Press HOME MENU to exit the menu.  
• You can return to the upper menu levels by pressing RETURN.  
30  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuner Setup  
09  
Setting for skipping unwanted channels  
From among TV channels searched and set up using Auto  
Channel Preset, you can select channels to be skipped when  
CH +/– are operated.  
Setting up TV channels  
This section describes how to search and set up TV channels  
that you can watch under the current conditions. Unless you set  
up TV channels using Auto Channel Preset, you may not be able  
to tune in those channels.  
Press HOME MENU.  
1
2
3
4
5
6
Select “Tuner Setup”. (  
/
then ENTER)  
Using Auto Channel Preset  
Auto Channel Preset automatically searches and sets up TV  
channels.  
Select “Channel Setup”. (  
/
then ENTER)  
Select “Ant. A” or “Ant. B”. (  
/
then ENTER)  
Select “Channel Keep/Skip”. (  
/
then ENTER)  
Press HOME MENU.  
1
2
3
4
5
6
Select a channel to be skipped. (  
/
then ENTER)  
Select “Tuner Setup”. (  
/
then ENTER)  
Channel Setup Ant. A  
Channel Keep/Skip  
Select “Channel Setup”. (  
/
then ENTER)  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Select “Ant. A” or “Ant. B”. (  
/
then ENTER)  
Ant. A  
Channel Keep/Skip  
2.0  
4.0  
6.0  
Select “Auto Channel Preset”. (  
/
then ENTER)  
Home Menu Exit  
Select “Air” or “Cable”. ( then ENTER)  
/
• For the skipped channel, a check mark disappears.  
Channel Setup  
Ant. A  
Ant. A  
Auto Ch. Preset Cable  
Press HOME MENU to exit the menu.  
7
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Air  
Cable  
Auto Channel Preset  
2.0  
4.0  
6.0  
D
Enter  
Home Menu  
Exit  
Begin Preset  
Cancel  
• To restore skipped channels, use the above procedure except that you  
select a skipped channel in step 6.  
• When using the Cable Converter, you may need to manually add  
Cable Converter output channels.  
• Channel search automatically starts.  
Channel Setup  
Ant. A  
Auto Ch. Preset Cable  
xxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxx  
One Moment Please …  
Ant. A  
Auto Channel Preset • Cable  
Setting up TV channels manually  
This section describes how to manually set up TV channels that  
have not been set up by Auto Channel Preset.  
D
Home Menu  
Cancel  
Exit  
Press HOME MENU.  
1
2
3
4
5
6
• To quit Auto Channel Preset halfway, press D.  
Select “Tuner Setup”. (  
/
then ENTER)  
After Auto Channel Preset has been finished, press  
HOME MENU to exit the menu.  
7
Select “Channel Setup”. (  
/
then ENTER)  
Select “Ant. A” or “Ant. B”. (  
/
then ENTER)  
Select “Add Channel”. (  
/
then ENTER)  
• When using the Cable Converter, you may need to manually add  
Cable Converter output channels.  
Select a channel number to be added. (  
• You can also use buttons 0 – 9 to enter a channel  
/
then ENTER)  
number.  
Channel Setup Ant. A  
Add Channel  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Ant. A  
Add Channel  
0000.000  
1
Home Menu Exit  
• After ENTER has been pressed, a confirmation screen  
appears.  
Press A to complete the setup processing.  
7
8
Press HOME MENU to exit the menu.  
31  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
09  
Tuner Setup  
Naming TV channels  
Checking the Cable Card ID  
You can name TV channels that you have set up for antenna B.  
This may help you easily identify the channels during selections.  
The Media Receiver has a slot for a cable card that is used for  
managing your information by the cable TV company. The  
following procedure allows you to check your Cable Card ID and  
the Host ID.  
Press HOME MENU.  
1
2
3
4
5
6
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “Name Channel”. ( then ENTER)  
Select a channel. ( then ENTER)  
Press HOME MENU.  
1
2
3
4
Select “Channel Setup”. (  
Select “Ant. B”. (  
/
Select “Tuner Setup”. (  
/
then ENTER)  
/ then ENTER)  
/
Select “Channel Setup”. (  
/
Select “POD ID”. (  
/
)
/
• The Host ID and Cable Card ID appear.  
• You can also use buttons 0 – 9 to enter a channel  
Press HOME MENU to exit the menu.  
5
number.  
Channel Setup Ant. B  
Name Channel  
Enabling data acquisition  
Use this function to enable the system to automatically acquire  
information about digital TV programs even when in the standby  
mode.  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Ant. B  
Name Channel  
Home Menu Exit  
Press HOME MENU.  
1
2
3
4
5
6
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
then ENTER)  
Press HOME MENU to exit the menu.  
7
Enter up to 7 alphanumeric characters using  
, and ENTER.  
• To clear the last character, press B.  
/
,
/
Select “Channel Setup”. (  
Select “Data Acqu”. (  
Select “Enabled”. (  
/
/
Channel Setup Ant. B  
Name Channel  
Name: DTV2  
/
A
K
U
5
)
B
L
V
6
,
C
M
W
7
D
N
X
8
E
O
Y
9
:
F
P
Z
0
'
G
Q
1
.
H
R
2
I
S
3
/
J
T
4
(
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Ant. B  
Name Channel  
@
–
_
&
S P A C E  
A
B
D
Home Menu  
Exit  
Accept  
Clear  
Cancel  
• The DATA ACQUISITION indicator on the front of the Media  
Receiver lights while data is being acquired.  
Press A.  
8
9
Press HOME MENU to exit the menu.  
Checking signal strength  
When you have selected antenna A, you can check the current  
channel’s signal strength. You may use this function when  
receiving a channel through a VHF/UHF antenna.  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “Channel Setup”. (  
Select “Ant. A”. (  
Select “Signal Strength”. (  
/
/
/
then ENTER)  
Channel Setup  
Ant. A  
Signal Strength  
Maximum: 100  
Current: 100  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Ant. A  
Signal Strength  
Home Menu  
Exit  
• Adjust the direction of the antenna so that the current  
signal strength reaches as close to the maximum signal  
strength as possible.  
Press HOME MENU to exit the menu.  
6
32  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuner Setup  
09  
TV Parental Guidelines  
Parental Control  
Content  
With the Parental Control, parents can prevent their children  
from watching inappropriate TV programs, VCR or DVD  
contents. When an attempt is made to watch a program (or  
content) blocked by parents, the Plasma Display shows nothing  
but a message. The Parental Control functions for both  
conventional and digital TV channels.  
FV  
V
S
L
D
Rating  
(Fantasy  
(Violence) (Sexual  
(Adult  
(Sexually  
suggestive  
dialog)  
violence)  
situations) language)  
TV-Y  
(All children)  
In the U.S. three rating systems have been provided: the TV  
ratings, TV Parental Guidelines, and movie ratings. Movie  
ratings are provided by the Motion Picture Association of  
America (MPAA) and are used for original movies not edited for  
television.  
TV-Y7  
(Directed to older children)  
X
TV-G  
Age-Base (General audience)  
For the rating system in Canada, see pages 36 and 37.  
TV-PG  
(Parental guidance suggested)  
X
X
X
X
X
X
X
X
X
X
X
Voluntary movie rating system (MPAA)  
TV-14  
Rating  
Description  
(Parents strongly cautioned)  
G
General audiences. All ages admitted.  
TV-MA  
PG  
Parental guidance suggested. Some material  
may not be suitable for children.  
(Mature audience only)  
X: Content rating can be set.  
PG-13  
Parents strongly cautioned. Some material  
may be inappropriate for children under 13.  
Age-Base R  
Restricted. Under 17 requires accompanying  
parent or adult guardian (age varies in some  
jurisdictions).  
Changing the password  
Using a password prevents other persons from changing  
Parental Control settings. A default password (1234) has been  
set before shipment. Use the following procedure to change the  
password.  
NC-17  
No one 17 and under admitted.  
Adult  
A rating that has now been superseded by  
NC-17.  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “Change Password”. ( then ENTER)  
NR  
Not rated.  
Select “Parental Control”. (  
Select “Password”. (  
/
/
/
• The voluntary movie rating system only uses an age-based rating.  
Parental Control  
Password  
xxxxxxxxxxxxxxxxxxxxx  
TV ratings  
Password  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Change Password  
Clear Password  
Rating  
Description  
Home Menu  
Exit  
TV-Y  
TV-PG  
TV-14  
TV-MA  
All children  
TV-Y7  
TV-G  
Children 7 and above  
General audiences  
Enter the current 4-digit password, using buttons 0 – 9.  
6
7
Age-Base  
Enter a 4-digit password to be newly set, using buttons  
Parental guidance suggested  
Parents strongly cautioned  
Mature audiences only  
0 – 9.  
Enter the same password that you have entered in step 7.  
• A confirmation screen appears.  
8
Press A.  
9
10  
Press HOME MENU to exit the menu.  
• Take a note of the newly set password and keep it handy.  
33  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
09  
Tuner Setup  
Clearing the password  
Use the following procedure to clear the password.  
Setting the voluntary movie rating system  
(MPAA)  
Press HOME MENU.  
1
2
3
4
5
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “Clear Password”. ( then ENTER)  
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “Parental Control”. (  
Select “Password”. (  
/
Select “Parental Control”. (  
Select “MPAA Ratings”. (  
/
/
/
/
Select the desired rating and change the setting. (  
then ENTER)  
/
Parental Control  
Password  
Parental Control  
MPAA Ratings  
MPAA Ratings  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Change Password  
Clear Password  
Password  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Blocked MPAA Ratings  
G, PG, PG-13, R, NC-17, Adult, NR  
G
PG  
Home Menu  
Exit  
PG-13  
Home Menu  
Exit  
Enter the current 4-digit password, using buttons 0 – 9.  
• A confirmation screen appears.  
6
• The password entry screen appears. Enter your 4-digit  
password using buttons 0 – 9.  
• Each time you press ENTER, the setting is switched.  
• A lock icon appears beside the blocked rating.  
• All the ratings have been unblocked before shipment.  
Press A.  
7
8
Press HOME MENU to exit the menu.  
Press HOME MENU to exit the menu.  
6
• The above procedure will reset the password to the factory default  
(1234).  
• Blocking a rating causes more severe ratings to be automatically  
blocked as well. Likewise, unblocking a rating causes less severe  
ratings to be automatically unblocked.  
Activating the Parental Control  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
then ENTER)  
Select “Parental Control”. (  
Select “Status”. (  
Select “On”. (  
/
/
/
• The password entry screen appears. Enter your 4-digit  
password using buttons 0 – 9.  
Press HOME MENU to exit the menu.  
6
• If you select “Off” in step 5, then select “Reset on Startup” or “Don’t  
Reset”. With “Reset on Startup” selected, the Parental Control is  
automatically activated when the power to the system is turned off  
and on. With “Don’t Reset” selected, the Parental Control remains off  
when the power to the system is off and on.  
We suggest you write down your password so you don’t forget it.  
If you forget the password  
PRO-1120HD/PRO-920HD  
Your password No.:  
When the message “Enter your Password” is displayed in  
step 6 under “Clearing the password”, press the ENTER  
button on the remote control unit and hold it down for 3  
seconds or longer.  
The password reverts to “1234”.  
34  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuner Setup  
09  
Setting the TV ratings  
Blocking Not Rated TV programs  
Use the following procedure to block TV programs whose rating  
information is unavailable.  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
Press HOME MENU.  
1
2
3
4
5
Select “Parental Control”. (  
Select “TV Ratings”. (  
/
then ENTER)  
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
/
then ENTER)  
Select “Parental Control”. (  
Select “Unavailable Ratings”. (  
Select “Block” or “Don’t Block”. (  
/
Select the desired rating and change the setting. (  
then ENTER)  
/
/
then ENTER)  
/
then ENTER)  
Parental Control  
TV Ratings  
Parental Control  
Unavailable Ratings  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
TV-Y  
Blocked TV Ratings  
TV Ratings  
TV-Y7  
TV-G  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Unavailable Ratings  
TV-PG  
Block  
Don’t Block  
Home Menu  
Exit  
Home Menu  
Exit  
• The password entry screen appears. Enter your 4-digit  
password using buttons 0 – 9.  
• Each time you press ENTER, the setting is switched.  
• A lock icon appears beside the blocked rating.  
• All the ratings have been unblocked before shipment.  
• The password entry screen appears. Enter your 4-digit  
password using buttons 0 – 9.  
• The factory default is “Don’t Block”.  
Press HOME MENU to exit the menu.  
6
Press HOME MENU to exit the menu.  
6
• Blocking a rating causes more severe ratings to be automatically  
blocked as well. Likewise, unblocking a rating causes less severe  
ratings to be automatically unblocked.  
Setting the TV Parental Guidelines (TV  
Guidelines)  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
Select “TV Parental Guidelines”. ( then ENTER)  
Select “Parental Control”. (  
/
/
Select the desired rating and change the setting. (  
then ENTER)  
/
Parental Control  
TV Parental Guidelines  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Blocked TV Parental Guidelines  
TV Parental Guidelines  
Fantasy Violence  
Violence  
Sexual Situations  
Home Menu  
Exit  
• The password entry screen appears. Enter your 4-digit  
password using buttons 0 – 9.  
• Each time you press ENTER, the setting is switched.  
• A lock icon appears beside the blocked rating.  
• All the ratings have been unblocked before shipment.  
Press HOME MENU to exit the menu.  
6
• Blocking a rating causes more severe ratings to be automatically  
blocked as well. Likewise, unblocking a rating causes less severe  
ratings to be automatically unblocked.  
35  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
09  
Tuner Setup  
Canadian French ratings  
Canadian rating systems  
Rating  
Description  
In Canada you can choose the Canadian English ratings or the  
Canadian French ratings. These ratings are based on the  
Canadian Radio-Television and Telecommunications  
Commission (CRTC) policy.  
E
Exempt programming.  
G
General: All ages and children, contains  
minimal direct violence, but may be  
integrated into the plot in a humorous or  
unrealistic manner.  
Canadian English ratings  
Rating  
Description  
8ans+  
General but inadvisable for young children:  
May be viewed by a wide public audience,  
but could contain scenes disturbing to  
children under eight who cannot distinguish  
between imaginary and real situations.  
Recommended for viewing with parent.  
E
Exempt: Includes news, sports, documenta-  
ries and other information programming; talk  
shows, music videos, and variety  
programming.  
Age-Base  
C
Children: Intended for younger children  
under the age of 8 years. Pays careful  
attention to themes that could threaten their  
sense of security and well-being.  
13ans+  
Over 13 years: Could contain scenes of  
frequent violent scenes and therefore  
recommended for viewing with parent.  
16ans+  
Over 16 years: Could contain frequent  
violent scenes and intense violence.  
C8+  
Children over 8 years old: Contains no  
portrayal of violence as the preferred,  
acceptable, or only way to resolve conflict;  
nor encourage children to imitate dangerous  
acts which they may see on the screen.  
18ans+  
Over 18 years: Only for adult viewing. Could  
contain frequent violent scenes and extreme  
violence.  
G
General: Considered acceptable for all age  
groups. Appropriate viewing for the entire  
family, contains very little violence, physical,  
verbal or emotional.  
Setting Canadian English ratings  
Age-Base  
PG  
Parental Guidance: Intended for a general  
Press HOME MENU.  
1
2
3
4
5
audience, but may not be suitable for  
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
Select “Canadian English Ratings”. ( then ENTER)  
younger children (under the age of 8)  
because it could contain controversial  
themes or issues.  
Select “Parental Control”. (  
/
/
14 +  
18 +  
Over 14 Years: Could contain themes where  
violence is one of the dominant elements of  
Select the desired rating and change the setting. (  
then ENTER)  
/
the storyline, but it must be integral to the  
development of plot or character. Language  
usage could be profane and nudity present  
within the context of the theme.  
Parental Control  
Canadian English Ratings  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Blocked Canadian English Ratings  
Canadian English Ratings  
E
C
Adults: Intended for viewers 18 years and  
older and might contain depictions of  
C8+  
Home Menu  
Exit  
violence, which while related to the develop-  
ment of plot, character or themes, are  
intended for adult viewing. Could contain  
graphic language and portrayals of sex and  
nudity.  
• The password entry screen appears. Enter your 4-digit  
password using buttons 0 – 9.  
• Each time you press ENTER, the setting is switched.  
• A lock icon appears beside the blocked rating.  
• All the ratings have been unblocked before shipment.  
Press HOME MENU to exit the menu.  
6
36  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuner Setup  
09  
Setting Canadian French ratings  
Setting your favorite channels  
Press HOME MENU.  
1
2
3
4
5
Set up to 10 TV channels to each of the four color buttons on  
the remote control unit (40 channels in total). You can then  
quickly select from only your favorite channels.  
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
Select “Canadian French Ratings”. ( then ENTER)  
Select “Parental Control”. (  
/
Press HOME MENU.  
1
2
3
4
5
/
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
Select a color button (A, B, C, D). (  
Select the desired rating and change the setting. (  
then ENTER)  
/
Select “Favorites”. (  
/
/
then ENTER)  
then ENTER)  
Parental Control  
Canadian French Ratings  
Select a TV channel to be registered. (  
/
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Blocked Canadian French Ratings  
E, G, 8 ans+, 13 ans+, 16 ans+, 18  
ans+  
Canadian French Ratings  
E
A
Favorites  
Favorites  
G
8 ans+  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Current Favorites A Line Up  
A4.0 A6.0  
Home Menu  
Exit  
A
Favorites  
A
A
A
2.0  
4.0  
6.0  
• The password entry screen appears. Enter your 4-digit  
password using buttons 0 – 9.  
Home Menu  
Exit  
• Each time you press ENTER, the setting is switched.  
• A lock icon appears beside the blocked rating.  
• All the ratings have been unblocked before shipment.  
• A star appears beside the favorite channels currently  
selected.  
• To register another TV channel under the same color  
button, repeat step 5. To register another TV channel  
under a different color button, repeat steps 4 and 5.  
Press HOME MENU to exit the menu.  
6
Press HOME MENU to exit the menu.  
6
Temporarily deactivating the Parental Control  
When the Parental Control is working and censors a blocked TV  
program (or content), the Plasma Display shows nothing but a  
message.  
The method for temporarily deactivating the Parental Control  
differs, depending on the currently selected input source.  
Setting up closed captions  
Your Plasma Display System is equipped with an internal closed  
caption decoder. Closed caption allows you to view  
conversations, narration, and sound effects in TV programs and  
home videos as subtitles on your Plasma Display screen.  
You may enjoy digital closed captions when watching digital TV  
programs. Digital closed captions allow you to change  
parameters such as fonts and colors.  
Antenna A, antenna B, or i.LINK:  
Press ENTER and then enter your 4-digit password.  
Parental Control  
WWWWWWW  
1000.0000  
(Ant. B)  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
• Not all programs and videos offer closed caption. Please look  
for the “  
” symbol to ensure that captions will be shown.  
Enter Disable Parental Control  
• The password entry screen stays only for one minute. After  
the screen disappears, pressing ENTER causes it to appear  
again.  
Input 1 – 4:  
Enter your 4-digit password. You need not press ENTER first,  
pressing ENTER causes the password entry screen to  
disappear.  
Please Input Your Password.  
• The above password entry screen will also be shown during  
2-screen mode, picture-in-picture, and while freezing an  
image.  
• The password entry screen stays only for one minute. After  
the screen disappears, pressing ENTER causes it to appear  
again.  
37  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
09  
Tuner Setup  
Activating the closed caption  
Selecting digital closed captions  
Use the following procedure to select digital closed captions.  
Press HOME MENU.  
1
2
3
4
5
Press HOME MENU.  
1
2
3
4
5
6
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “On” or “On If Mute”. ( then ENTER)  
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
Select “Closed Captions”. (  
Select “Status”. (  
/
Select “Closed Captions”. (  
Select “Digital Settings”. (  
Select “Digital Service”. (  
/
/
/
then ENTER)  
/
/
then ENTER)  
Closed Captions  
Status  
Select the desired closed caption. (  
/
then ENTER)  
Off  
On  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Status  
On If Mute  
Closed Captions  
Digital Settings  
Digital Service  
Service 1  
Service 2  
Service 3  
Service 4  
Service 5  
Home Menu  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Exit  
Digital Settings  
Digital Service  
Item  
Description  
Home Menu  
Exit  
Off  
Does not show closed captions.  
Always shows closed captions.  
(factory default)  
On  
• The factory default is “Service 1”.  
Press HOME MENU to exit the menu.  
7
On If Mute  
Shows closed captions only while sound is  
being muted.  
• The Primary Caption Service is usually offered for Service 1,  
and the Secondary Language Service is usually offered for  
Service 2 if these services are available.  
Press HOME MENU to exit the menu.  
6
Selecting digital closed caption parameters  
Use the following procedure to change such parameters of  
digital closed captions as font size, font type, foreground and  
background colors.  
• For MONITOR OUT, only conventional closed caption signals are  
output; digital closed caption signals are not output.  
Selecting the type of conventional closed  
captions  
Select the type of conventional closed captions that you will  
watch after tuning to a conventional TV channel. This selection  
also becomes effective when a selected digital TV program  
provides only conventional closed captions.  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “Closed Captions”. (  
Select “Digital Settings”. (  
/
/
Select “Font Size”, “Font”, or any other item. (  
ENTER)  
/
then  
• “CC1”, “CC2”, “CC3”, or “CC4” displays subtitles of TV dramas  
and news programs while allowing a full view of the picture.  
6
Select the desired parameter. (  
/
then ENTER)  
• “Text1”, “Text2”, “Text3”, or “Text4” superimposes on the  
picture other information (e.g. TV guide, weather) that is  
independent of the TV in progress.  
Closed Captions  
Digital Settings  
Font Size  
Large  
Standard  
Small  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Digital Settings  
Font Size  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Home Menu  
Exit  
Select “Closed Captions”. (  
Select “Analog Settings”. (  
/
/
7
8
Repeat steps 5 and 6 as necessary. (  
,
/
)
Select the desired closed caption. (  
/
then ENTER)  
Press HOME MENU to exit the menu.  
Closed Captions  
Analog Settings  
CC1  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
CC2  
Analog Settings  
CC3  
CC4  
Text 1  
Home Menu  
Exit  
• The factory default is “CC1”.  
Press HOME MENU to exit the menu.  
6
38  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Tuner Setup  
09  
The following table shows the parameters selectable for each  
item.  
7
Select “Applies” or “Does Not Apply”. (  
• Make this selection, depending on whether summer  
time is employed in your area.  
/
then ENTER)  
Item  
Selection  
Font Size  
Auto/ Large/ Standard/ Small  
Clock  
Daylight Savings Time  
1
Font  
Auto/ Font 1/ Font 2/ Font 3/ Font 4/  
Current Time:  
9:56 pm EDT  
Monday  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
D.S.T.  
Font 5/ Font 6/ Font 7  
Applies  
Does Not Apply  
05/17/04  
Font Color  
Auto/ Black/ White/ Red/ Green/ Blue/  
Home Menu  
Exit  
Yellow/ Magenta/ Cyan  
Font Opacity  
Background Color  
Auto/ Solid/ Transparent/ Translucent/  
8
9
10  
Select “Auto/Manual Set”. (  
,
/
, then ENTER)  
Select “Auto Set” or “Manual Set”. ( then ENTER)  
If you select “Auto Set”, select an antenna (A or B) and a  
Flashing  
/
Auto/ Black/ White/ Red/ Green/ Blue/  
Yellow/ Magenta/ Cyan  
channel number using  
/
and ENTER.  
Background Opacity Auto/ Solid/ Transparent/ Translucent  
Clock  
Auto/Manual Set  
Clock Set Channel  
1
Font 1 (monospaced with serifs)/ Font 2 (proportionally spaced with  
serifs)/ Font 3 (monospaced without serifs)/ Font 4 (proportionally  
spaced without serifs)/ Font 5 (casual font)/ Font 6 (cursive font)/  
Font 7 (small capitals font)  
Current Time:  
11:58 pm PDT  
Monday  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Auto/Manual Set •Auto Set  
Ant. A  
2.0  
05/17/04  
Home Menu  
Exit  
With “Auto” selected, parameters specified by the provider are  
used; if not specified by the provider, the bolded default  
parameters are used. If you select parameters other than  
“Auto”, the selected parameters are used regardless of  
provider’s specifications.  
• The date and time will be automatically corrected using  
data from the selected channel.  
If you select “Manual Set”, manually set the date and  
time using  
/
,
/
and ENTER.  
Clock  
Auto/Manual Set  
Date and Time  
3
Current Time:  
4
3
5
6
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Clock Setting  
11:58 pm PDT  
Monday  
Auto/Manual Set •Manual Set  
/17/04 11:58pm  
With “Auto Set” selected for Clock Setting, the system acquires  
and sets time information automatically. You can also manually  
set the correct time. If you disconnect the power cord from the  
power outlet or power blackout occurs, the set time is cleared.  
05/17/04  
Home Menu  
Exit  
Press HOME MENU to exit the menu.  
11  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
• When the time has not been set, the REC TIMER indicator on the  
front of the Media Receiver blinks.  
• When the time has not yet been set, you cannot view channel banner  
information, use auto channel select, and preset TV programs for  
recording.  
Select “Clock”. (  
Select “Time Zone”. (  
Select a time zone for your area. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
/
/
Clock  
Time Zone  
Current Time:  
9:55 pm EDT  
Monday  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
Atlantic  
Eastern  
Central  
Time Zone  
05/17/04  
Mountain  
Home Menu  
Exit  
6
Select “D.S.T.” (  
,
/
, then ENTER)  
39  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Adjustments and Settings  
Sleep Timer  
You can also use the menu to change the options.  
Press HOME MENU.  
1
2
3
4
When the selected time elapses, the Sleep Timer automatically  
places the system into the standby mode.  
Select “Picture”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
Select “AV Selection”. (  
/
Press SLEEP to select the desired time.  
• The timer starts counting.  
Select the desired option. (  
/
• Each time you press SLEEP, the selection is switched as  
below:  
AV Selection  
STANDARD  
DYNAMIC  
MOVIE  
30  
60  
90  
Off  
120  
(cancel)  
(minutes)  
GAME  
USER  
• The factory default is “Off”.  
• To cancel the Sleep Timer, select “Off” by pressing SLEEP.  
• Five minutes before the selected time elapses, the remaining time  
appears every minute.  
For AV source  
Item  
Description  
STANDARD  
For a highly defined image in a normally  
bright room  
You can also use the menu to set the Sleep Timer.  
DYNAMIC  
For a very sharp image with the maximum  
Press HOME MENU.  
1
2
3
4
contrast  
This mode does not allow manual image  
Select “Sleep Timer”. (  
/
then ENTER)  
quality adjustment.  
Select the desired time. (  
/
then ENTER)  
MOVIE  
GAME  
USER  
For a movie  
Press HOME MENU to exit the menu.  
Lowers image brightness for easier viewing.  
Allows the user to customize settings as  
desired. You can set the mode for each input  
source.  
AV Selection  
Select from the five viewing options, depending on the current  
environment (e.g., room brightness), the type of the current TV  
program, or the type of images input from external equipment.  
For PC source  
Item  
Press AV SELECTION.  
• The current AV Selection mode appears.  
1
2
Description  
STANDARD  
For a highly defined image in a normally  
Press AV SELECTION again before the displayed mode  
disappears.  
(factory default) bright room  
USER  
Allows the user to customize settings as  
• For AV source, the mode is switched in the order;  
STANDARD, DYNAMIC, MOVIE, GAME, then USER.  
• For PC source, the mode is switched between  
STANDARD and USER.  
desired. You can set the mode for each input  
source.  
Press HOME MENU to exit the menu.  
5
40  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments and Settings  
Picture adjustments  
10  
For PC source  
Item  
button  
button  
Adjust the picture to your preference for the chosen AV  
Selection option (except DYNAMIC).  
Contrast  
Brightness  
Red  
For less contrast  
For less brightness  
For weaker red  
For more contrast  
For more brightness  
For stronger red  
Press HOME MENU.  
1
2
3
Select “Picture”. (  
/
then ENTER)  
Green  
For weaker green  
For weaker blue  
For stronger green  
Select an item to be adjusted. (  
/
then ENTER)  
Blue  
For stronger blue  
Picture  
AV Selection  
Contrast  
Brightness  
Color  
STANDARD  
40  
0
• To make settings for “PureCinema”, “Color Temp”, “MPEG NR”,  
“DNR”, “CTI”, and “DRE”, select “Pro Adjust” in step 3, and then press  
ENTER. For the subsequent procedures, see “Pro Adjust”.  
0
Tint  
0
• To restore the factory defaults for all the items, press  
“Reset” in step 3, and then press ENTER. A confirmation screen  
appears. Press  
/
to select  
Sharpness  
Pro Adjust  
Reset  
0
/
to select “Yes”, and then press ENTER.  
Pro Adjust  
This system provides various advanced functions for optimizing  
the picture quality.  
For PC source, the following screen appears:  
Picture  
Press HOME MENU.  
1
2
3
4
AV Selection  
Contrast  
Brightness  
Red  
STANDARD  
Select “Picture”. (  
Select “Pro Adjust”. (  
Select an item to be adjusted. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
40  
0
/
/
• You can select “PureCinema”, “Color Temp”,  
“MPEG NR”, “DNR”, “CTI”, or “DRE”.  
0
Green  
0
5
Select the desired parameter. (  
• For the selectable parameters, see the table.  
/
then ENTER)  
Blue  
0
Reset  
PureCinema  
Automatically detects a film-based source (originally encoded at  
24 frames/second), analyzes it, then recreates each still film  
frame for high-definition picture quality.  
4
5
Select the desired level. (  
/
then ENTER)  
Contrast  
40  
Selections  
Remark  
Off  
Deactivates the PureCinema.  
Standard  
Produces smooth and vivid moving  
images (film specific) by  
automatically detecting recorded  
• When an adjustment screen is in display, you can also  
change an item to be adjusted, by pressing  
image information when displaying  
/
.
DVD or 1080i HDTV images (e.g.,  
movies) having 24 frames per  
second.  
Press HOME MENU to exit the menu.  
For AV source  
ADV  
Produces smooth and quality moving  
images (as shown on theater  
Item  
button  
button  
screens) by converting to 72 Hz  
when displaying DVD images (e.g.,  
Contrast  
Brightness  
Color  
For less contrast  
For more contrast  
For less brightness  
For more brightness  
movies) having 24 frames per  
second.  
For less color intensity For more color intensity  
You cannot select “Standard” when 480p or 720p  
signals are being input.  
Tint  
Skin tones become  
Skin tones become  
purplish  
greenish  
Sharpness  
For less sharpness  
For more sharpness  
41  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Adjustments and Settings  
Color Temp  
Selections  
DNR  
Selections  
Adjusts the color temperature, resulting in a better white  
balance.  
Eliminates video noise for clean crisp images. The DNR stands  
for Digital Noise Reduction.  
High  
White with bluish tone  
Off  
Deactivates the DNR.  
Enhanced DNR  
Standard DNR  
Mid-High  
Intermediate tone between High and  
Mid  
High  
Mid  
Low  
Mid  
Natural tone  
Moderate DNR  
Mid-Low  
Intermediate tone between High and  
Low  
CTI  
Low  
White with reddish toneMid-Low  
Provides images with clearer color contours. The CTI stands for  
Color Transient Improvement.  
Manual  
Allows you to manually adjust the  
color temperature. Use the following  
procedure.  
Selections  
Off  
Deactivates the CTI.  
On  
Activates the CTI.  
1 Select “Manual”, and then press and hold ENTER for more  
than three seconds to display the manual adjustment  
screen.  
DRE  
Adjusts dark and bright portions on images so that the contrast  
between brightness and darkness becomes clearer.  
2 Select an item to be adjusted. (  
/
then ENTER)  
3 Select the desired level. ( / then ENTER)  
Selections  
Off  
Deactivates the DRE.  
Enhanced DRE  
Standard DRE  
Item  
button  
button  
High  
Mid  
Low  
R High  
For weaker red  
For stronger red  
G High  
B High  
R Low  
G Low  
B Low  
For weaker green  
For weaker blue  
For weaker red  
For weaker green  
For weaker blue  
For stronger green  
For stronger blue  
For stronger red  
For stronger green  
For stronger blue  
Moderate DRE  
Color Management  
Adjusts the hue for each basic color. Use the following  
procedure.  
1 Select an item to be adjusted. (  
2 Select the desired level. (  
/
then ENTER)  
• To perform adjustment for another item, press RETURN,  
and then repeat steps 2and 3.  
/
)
• You may press  
adjusted.  
/
to immediately change an item to be  
Item  
button  
Closer to yellow  
Closer to green  
Closer to cyan  
Closer to blue  
button  
Red  
Closer to magenta  
Closer to red  
Closer to yellow  
4 Press HOME MENU to exit the menu.  
Yellow  
Green  
Cyan  
Closer to green  
Closer to cyan  
Closer to blue  
Closer to magenta  
Closer to red  
MPEG NR  
Eliminates mosquito noise from video images when a digital TV  
channel is watched or a DVD is played, resulting in noise-free  
images.  
Blue  
Magenta  
Selections  
Off  
Deactivates the MPEG NR.  
Enhanced MPEG NR  
Standard MPEG NR  
• To perform adjustment for another item, press  
High  
Mid  
Low  
RETURN, and then repeat steps 1 and 2.  
• You may press  
be adjusted.  
/
to immediately change an item to  
Moderate MPEG NR  
3 Press HOME MENU to exit the menu.  
42  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments and Settings  
Sound adjustments  
10  
FOCUS  
This shifts the sound coming direction (sound images) upward  
and produces clear sound contours.  
Adjust the sound to your preference for the chosen AV  
Selection option. See page 40.  
Press HOME MENU.  
1
2
3
4
Press HOME MENU.  
1
2
3
4
Select “Sound”. (  
Select “FOCUS”. (  
/
then ENTER)  
Select “Sound”. (  
/
then ENTER)  
/
)
Select an item to be adjusted. (  
/
)
Select the desired parameter. (  
/
)
Select the desired level. (  
/
)
Item  
Description  
Sound STANDARD  
Off  
Deactivates the FOCUS.  
Activates the FOCUS.  
(factory default)  
Treble  
2
0
0
Bass  
On  
Balance  
Reset  
Press HOME MENU to exit the menu.  
5
FOCUS  
Front Surround  
Off  
Off  
Front Surround  
This provides three-dimensional sound effects and/or deep, rich  
bass.  
Press HOME MENU.  
1
2
3
4
Item  
Balance  
button  
button  
Select “Sound”. (  
Select “Front Surround”. (  
Select the desired parameter. (  
/
then ENTER)  
Treble  
For weaker treble  
For weaker bass  
For stronger treble  
For stronger bass  
/
)
Bass  
/
)
Decreases audio from Decreases audio from  
Item  
Description  
the right speaker  
the left speaker  
Off  
Deactivates both the SRS and TruBass.  
SRS  
Reproduces highly effective three-  
dimensional sound.  
Press HOME MENU to exit the menu.  
5
TruBass  
Provides deep, rich bass using a new  
(factory default)  
technology.  
• To restore the factory defaults for all the items, press  
“Reset” in step 3, and then press ENTER. A confirmation screen  
appears. Press to select “Yes”, and then press ENTER.  
/
to select  
TruBass + SRS  
Provides both TruBass and SRS effects.  
/
Press HOME MENU to exit the menu.  
5
•
•
(WOW) designates a status where the FOCUS is on and  
TruBass + SRS has been selected for Front Surround.  
is a trademark of SRS Labs, Inc.  
• WOW technology is incorporated under license from SRS Labs, Inc.  
43  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Adjustments and Settings  
No Operation off (AV mode only)  
The system will be automatically placed into the standby mode  
when no operation is performed for three hours.  
Power Control  
Power Control provides convenient functions for power saving.  
Press HOME MENU.  
1
2
3
4
Energy Save  
You can save power consumption by decreasing the picture  
brightness. When you need not watch the screen and want to  
enjoy only audio, you can also deactivate the screen.  
Select “Power Control”. (  
/
then ENTER)  
Select “No Operation off”. (  
/
then ENTER)  
Select “Enable”. (  
/
then ENTER)  
Press HOME MENU.  
Select “Power Control”. (  
Select “Energy Save”. (  
1
2
3
4
Item  
Description  
/
then ENTER)  
Disable  
Does not place the system into the  
(factory default) standby mode.  
/
then ENTER)  
Enable  
Places the system into the standby mode if  
Select “Save” or “Picture Off”. (  
/
then ENTER)  
no operation is performed for three hours.  
Item  
Description  
Standard  
Does not decrease picture brightness.  
Press HOME MENU to exit the menu.  
(factory default)  
5
Save  
Decreases picture brightness to save power.  
Picture Off  
Deactivates the screen to save power. To  
restore the screen display, press any button  
• Five minutes before the system is placed into the standby mode, a  
message appears every minute.  
other than VOL +/– and MUTING.  
This setting is not memorized by the system.  
Power Management (PC mode only)  
The system will be automatically placed into the standby mode  
when no signal is received from the personal computer.  
Press HOME MENU to exit the menu.  
5
Press HOME MENU.  
1
2
3
4
Select “Power Control”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
• You can also select this function using the Home menu when the  
input source is a PC.  
Select “Power Management”. (  
Select “Mode1” or “Mode2”. (  
/
/
No Signal off (AV mode only)  
Item  
Description  
The system will be automatically placed into the standby mode  
if no signal is received for 15 minutes.  
Off  
No power management  
(factory default)  
Press HOME MENU.  
1
2
3
4
Mode1  
• Places the system into the standby mode  
Select “Power Control”. (  
Select “No Signal off”. (  
/
then ENTER)  
when no signal is received from the  
personal computer for eight minutes.  
• Even when you start using the computer  
/
then ENTER)  
Select “Enable”. (  
/
then ENTER)  
and a signal is received again, the system  
stays off.  
Item  
Description  
• The system is switched on again by  
pressing STANDBY/ON on the Plasma  
Disable  
Does not place the system into the  
(factory default) standby mode.  
Display or TV on the remote control  
unit.  
Enable  
Places the system into the standby mode if  
no signal is received for 15 minutes.  
Mode2  
• Places the system into the standby mode  
when no signal is received for eight  
seconds.  
Press HOME MENU to exit the menu.  
5
• When you start using the computer and a  
signal is received again, the system is  
switched on.  
• Five minutes before the system is placed into the standby mode, a  
message appears every minute.  
• The system may not be placed into the standby mode when noise  
signals are present at the Media Receiver after a TV program finishes.  
• The system is switched on again by  
pressing STANDBY/ON on the Plasma  
Display or TV on the remote control  
unit.  
Press HOME MENU to exit the menu.  
5
44  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments and Settings  
10  
Adjusting image positions  
(AV mode only)  
• When Auto Setup is finished, “Auto Setup completed.” appears.  
• Even when “Auto Setup completed.” appears, Auto Setup may have  
failed, depending on conditions.  
• Auto Setup may fail with a PC image composed of similar patterns or  
monochrome. If not successful, change the PC image and try again.  
• Be sure to connect the computer to the Media Receiver and switch it  
on before starting Auto Setup.  
Adjust the horizontal and vertical positions of images on the  
Plasma Display.  
Press HOME MENU.  
1
2
3
4
Select “Option”. (  
Select “Position”. (  
/
then ENTER)  
/
then ENTER)  
Select “H/V Position Adjust”. (  
/
then ENTER)  
Adjusting image positions and clock  
manually (PC mode only)  
Position  
H/V Position Adjust  
Reset  
Usually you can easily adjust the positions and clock of images  
using Auto Setup. Use Manual Setup to optimize the positions  
and clock of images when necessary.  
Press HOME MENU.  
1
2
3
4
Select “Option”. (  
/
then ENTER)  
then ENTER)  
5
6
Adjust the vertical position (  
).  
Press HOME MENU to exit the menu.  
/
) or horizontal position  
Select “Manual Setup”. (  
/
(
/
Select an item to be adjusted. (  
/
then ENTER)  
Manual Setup  
• To restore the factory defaults for all the items, press  
“Reset” in step 4, and then press ENTER. A confirmation screen  
appears. Press to select “Yes”, and then press ENTER.  
/
to select  
H/V Position Adjust  
Clock  
0
0
/
• Adjustments are stored separately according to input source.  
Phase  
Reset  
Adjusting image positions and clock  
automatically (PC mode only)  
5
6
Perform adjustment. (  
• Use  
after selecting “H/V Position Adjust”.  
/
and  
/
)
Use Auto Setup to automatically adjust positions and clock of  
images coming from a personal computer.  
/
only when you adjust the vertical position  
Press HOME MENU.  
1
2
3
Press HOME MENU to exit the menu.  
Select “Option”. (  
/
then ENTER)  
then ENTER)  
Select “Auto Setup”. (  
/
• To restore the factory defaults for all the items, press  
“Reset” in step 4, and then press ENTER. A confirmation screen  
appears. Press to select “Yes”, and then press ENTER.  
/
to select  
Option  
/
Auto Setup  
Manual Setup  
• Auto Setup starts.  
Press HOME MENU to exit the menu.  
4
45  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Adjustments and Settings  
AV mode  
Selecting a screen size  
In single-screen mode, press SCREEN SIZE to change the size  
of the screen from among the selectable options for the type of  
video signals currently received.  
4:3  
• The selectable screen sizes differ depending on the types of  
input signals.  
AV mode  
WIDE  
FULL  
Item  
Description  
4:3  
For 4:3 “standard” pictures. A side bar appears on  
each side.  
FULL  
For 16:9 squeeze pictures.  
CINEMA  
ZOOM  
ZOOM  
For 16:9 letterbox pictures. Bars may appear on the  
top and bottom with some programs.  
CINEMA  
For 14:9 letterbox pictures. Bars may appear on the  
top and bottom on some programs.  
WIDE  
In this mode pictures are progressively stretched  
toward each side of the screen.  
PC mode except for XGA signals  
4:3  
PC mode except for XGA signals  
Item  
Description  
4:3  
Fills the screen without altering the input signal  
aspect ratio.  
FULL  
Full 16:9 screen display  
Dot by  
Dot  
Dot by Dot Matches input signal with same number of screen  
FULL  
pixels.  
PC mode for XGA signals  
(Ex. 1024 × 768 input at PRO-1120HD)  
PC mode for XGA signals  
Item  
4:3  
Description  
Matches input signal with the same number of  
screen pixels.  
Optimized for 1024 × 768 display  
4:3  
FULL1  
Full 16:9 screen display  
Optimized for 1024 × 768 display  
FULL2  
For wide signal display  
Use when displaying 1280 × 768 signal resolution.  
FULL2  
FULL1  
• In 2-screen mode, press SCREEN SIZE to change the size of left  
screen.  
• The PC mode above is for the PRO-1120HD. For the PRO-920HD the  
number of panel pixels is different, so signal processing and actual  
viewing conditions will vary slightly.  
• While watching High Definition TV broadcasting, pressing SCREEN  
SIZE switches between FULL and WIDE.  
• If you watch High Definition TV broadcasting with WIDE  
selected, part of the screen (e.g., images, graphic interface)  
can be missed. If this is the case, select FULL.  
46  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjustments and Settings  
10  
Changing the brightness at both sides of  
the screen (Side Mask)  
With the 4:3 screen size selected for the AV mode, you can  
change the brightness of the gray side masks that appear at  
both sides of the screen.  
Press HOME MENU.  
1
2
3
4
Select “Option”. (  
Select “Side Mask”. (  
Select the desired parameter. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
/
/
Item  
Description  
Fixed  
Always sets the same brightness for the  
(factory default) gray side masks.  
Auto  
Adjusts the brightness of the gray side masks  
according to the brightness of images.  
Press HOME MENU to exit the menu.  
5
Language setting  
You can select a language to be used for on-screen display such  
as menus from among three languages: English, French, and  
Spanish.  
Press HOME MENU.  
1
2
3
4
Select “Option”. (  
/
then ENTER)  
/ then ENTER)  
Select “Language”. (  
Select a language. (  
/
)
Language  
Menu  
English  
Press HOME MENU to exit the menu.  
5
47  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Timer Presetting  
7
8
9
Specify a channel number. (  
digit)  
/
then ENTER for each  
Presetting TV programs using the timer  
Using the menu, you can easily preset TV programs for  
watching later (auto channel select), recording with a D-VHS  
recorder, or recording via the supplied VCR controller.  
Timers  
Day(s)  
Start/End Times Channel  
Recording Device  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
None  
With the power to the system left on, the Auto Channel Preset  
automatically selects the preset TV program when its on-air  
time comes. Then you will not miss an important TV program  
when you are enjoying another TV program.  
For the connections with a D-VHS recorder, see pages 54 and  
55. For the connections with the supplied VCR controller, see  
page 59.  
•1  
Wed 5/19 3:58p - 10:58p  
A
2.0  
xxxxxxxxxxxxxxxxxxxxx  
A
B
D
Home Menu  
New Timer  
Suspend Timer  
Clear Timer  
Exit  
Select a recording device. (  
• To preset for auto channel select, select “None”.  
/
then ENTER)  
Timers  
Day(s)  
Start/End Times Channel  
Recording Device  
Name  
Advantz  
D-VHS  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
• You can make up to 32 presettings in total.  
•1  
Tue. 5/18 12:03a - 1:03a  
A
2.0  
• In steps 4 to 8, you can also press  
/
to move the cursor.  
A
B
D
Home Menu  
Exit  
New Timer  
Suspend Timer  
Clear Timer  
Press HOME MENU.  
1
2
3
Select “Timers”. (  
/
then ENTER)  
then ENTER)  
Press HOME MENU to exit the menu.  
Select a list number. (  
/
An alarm screen appears slightly before the preset timer is  
activated. If watching a TV channel through antenna A or B in a  
single-screen mode, the screen allows you to cancel the  
presetting by pressing D.  
TimerTsiers Day(s)  
Start/End Times Channel  
Recording Device  
None  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
•1  
Mon 5/17 9:58p - 10:58p  
A
2.0  
A
B
D
Home Menu  
Exit  
New Timer  
Suspend Timer  
Clear Timer  
Timer Alert  
The Following timer is about to begin:  
Sun. 1/0 12:00 am – 12:00 am  
Ant. A 0.0  
4
Specify a date. (  
/
then ENTER)  
• The selections include the days of the week (e.g.,  
Mondays), “Weekdays”, “Weekends”, and “Everyday”.  
Selecting one of these will cause the timer to activate  
periodically.  
A
D
Accept  
Cancel Timer  
The icons beside the list numbers have the following meanings.  
Icon  
Meaning  
Timers  
Day(s)  
Mon. 5/17  
Tue. 5/18  
Wed. 5/19 9:58p - 10:58p  
Thu. 5/20  
Start/End Times Channel  
Recording Device  
None  
Preset for recording; no conflicts with other timers  
exist.  
REC  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
•1  
A
2.0  
Fri.  
New Timer  
5/21  
Preset for auto channel select; no conflicts with  
A
B
D
Home Menu  
Exit  
Suspend Timer  
Clear Timer  
other timers exist.  
Preset for recording; conflicts with other timers exist.  
REC  
REC  
5
6
Specify the start and end times. (  
each field)  
/
then ENTER for  
Preset for auto channel select; conflicts with other  
timers exist.  
Timers  
Day(s)  
Start/End Times Channel  
1
Recording Device  
None  
Preset for recording; the timer start has been  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
2
delayed.  
•1  
Wed 5/13:58p - 10:58p  
A
2.0  
4
5
B
Preset for auto channel select; the timer start has  
A
D
Home Menu  
Exit  
New Timer  
Suspend Timer  
Clear Timer  
been delayed.  
Select antenna A or B. (  
/
then ENTER)  
Timers  
Day(s)  
Start/End Times Channel  
Recording Device  
None  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
•1  
Wed 5/19 3:58p - 10:58p  
A
2.0  
A
B
D
Home Menu  
Exit  
New Timer  
Suspend Timer  
Clear Timer  
48  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Timer Presetting  
11  
• If you set a timer to record a future digital program on a VCR, you  
must first turn off Parental Control. Otherwise, you will record only a  
black screen. See “Temporarily deactivating the Parental Control” on  
page 37.  
• To change the TV program presetting, repeat the above procedure. To  
cancel the presetting, press D after selecting a list number in step 4.  
• Switch on the recording equipment at least 30 seconds before the  
start of the preset program; otherwise recording will not be executed.  
• When presetting for recording, finish the operations two minutes  
(one minute for auto channel select) before the start of the program;  
otherwise presetting may fail.  
• Auto channel select is not executed when the system is in the  
standby mode.  
• Recording is not executed if recordable D-VHS tape is not present in  
the D-VHS recorder when the preset program starts. This is also true  
when a specified D-VHS recorder is not in connection.  
• For recording with a VCR, confirm that the video output terminals on  
the Media Receiver have been connected to the signal input  
terminals on the VCR.  
• Presettings become ineffective if the start time and the end time are  
identical.  
Priority rules for overlapped presettings  
When preset TV programs are overlapped, the following three  
rules are used to determine a higher priority. If more than one of  
the three rules are met, the rules are applied in the order; 1, 2,  
then 3.  
Rule 1: Presetting for recording is given a higher priority over  
presetting for auto channel select.  
Presetting for recording  
Presetting for auto  
channel select  
The shaded area is not executed.  
Rule 2: If two presettings are overlapped, presetting with  
earlier start time is given a higher priority. If two  
presettings are sequential, the last portion of the first  
program may not be recorded for 60 seconds (or  
less) because recording of the second program is  
started at the exact start time.  
Program A  
Program B  
The shaded area is not executed.  
Rule 3: If presettings at the same start time are overlapped,  
presetting with a higher list number is given a higher  
priority.  
49  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Enjoying through External Equipment  
You can connect many types of external equipment to your  
Plasma Display System, like a DVD player, VCR, personal  
computer, game console, and camcorder.  
To view images coming from external equipment, select the  
input source using the INPUT buttons on the remote control  
(page 14) or the INPUT button on the Plasma Display.  
Displaying a DVD image  
To watch a DVD image, press INPUT 1 on the remote control  
unit or press INPUT on the Plasma Display to select INPUT1.  
• Refer to your DVD player instruction manual for the signal type.  
• The INPUT 1 terminals are checked for cable connections in the  
order where; 1) Component Video, 2) S-Video, 3) Video.  
• Connect external equipment to only terminals that are to be actually  
used.  
• You can also use the INPUT 3 terminals when connecting only with  
the Component Video output terminals on a DVD player.  
• To protect all equipment, always turn off the system before  
connecting to a DVD player, VCR, personal computer, game  
console, camcorder, or other external equipment.  
• Refer to the relevant instruction manual (DVD player, personal  
computer, etc.) carefully before making connections.  
Watching a VCR image  
Watching a DVD image  
Connecting a VCR  
Use the INPUT 2 terminals when connecting a VCR and other  
audiovisual equipment.  
Connecting a DVD player  
Use the INPUT 1 terminals when connecting a DVD player and  
other audiovisual equipment.  
Media Receiver (rear view)  
DIGITAL OUT  
OPTICAL  
I N  
CONTROL  
ANTENNA  
OUT  
VCR CONTROL  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
IN  
B
AV cable (commercially available)  
S400  
(TS)  
S-VIDEO INPUT  
2
INPUT  
1
COMPONENT VIDEO  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
Media  
SERVICE ONLY  
Component Video cable  
(commercially available)  
Receiver  
OUT  
INPUT  
1
INPUT  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
HDMI  
MONITOR OUT  
VIO  
AUDIO
S-O  
S-VIDEO  
INPUT  
INPUT  
3
3
(rear view)  
DIGITAL OUT  
OPTICAL  
AV cable  
(commercially available)  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
S40
(TS)  
NPUT  
2
INPUT  
1
COMPOENT VIDO  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-
C
B
P  
B
C
R
P  
R
S-Video cable  
(commercially available)  
INPUT  
1
VIDEO  
R-AUDIO-L  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
HDMI  
S-VIDEO  
INPUT  
3
S-Video cable  
(commercially available)  
VCR  
Displaying a VCR image  
To watch a VCR image, press INPUT 2 on the remote control  
unit or press INPUT on the Plasma Display to select INPUT2.  
DVD player  
• The INPUT 2 terminals are checked for cable connections in the  
order where; 1) S-Video, 2) Video.  
• Connect external equipment to only terminals that are to be actually  
used.  
50  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying through External Equipment  
Using HDMI Input  
12  
To activate the HDMI terminal:  
Press HOME MENU.  
1
2
3
4
5
The INPUT 1 and INPUT 3 terminals include HDMI terminals to  
which digital video and audio signals can be input. To use the  
HDMI terminal, activate the terminal and specify the types of  
video and audio signals to be received from the connected  
equipment. For the types of these signals, see the operation  
manual that came with the connected equipment.  
Select “Option”. (  
/
then ENTER)  
Select “HDMI Input”. (  
/
then ENTER)  
Select “Setting”. (  
Select “Enable”. (  
Item  
/
then ENTER)  
then ENTER)  
/
Before starting the menu, press INPUT 1 (or INPUT 3) on the  
remote control unit or press INPUT on the Plasma Display to  
select INPUT 1 (or INPUT 3).  
Description  
Disable  
Deactivates the HDMI terminal.  
(factory default)  
Input signal correlation table  
Enable  
Activates the HDMI terminal.  
1920 10[email protected]/60Hz  
∗
720 [email protected]/60Hz  
∗
Press HOME MENU to exit the menu.  
6
1280 [email protected]/60Hz  
∗
To specify the type of digital video signals:  
720(1440) [email protected]/60Hz  
∗
Press HOME MENU.  
1
2
3
4
5
Select “Option”. (  
Select “HDMI Input”. (  
Select “Video”. ( then ENTER)  
/
then ENTER)  
/
then ENTER)  
• PC signals are not supported.  
/
Select the type of digital video signals. (  
ENTER)  
/
then  
Connecting HDMI equipment  
• If you select “Auto”, an attempt will be made to identify  
the type of digital video signals when digital video  
signals are received.  
Media Receiver (rear view)  
DIGITAL OUT  
OPTICAL  
S400  
Item  
Description  
(TS)  
INPUT  
1
COMPONENT VIDEO  
VIDEO  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
Auto  
Automatically identifies input digital video  
(factory default) signals.  
INPUT  
1
INPUT  
3
RUDIO-
Y
C
B
/P  
B
C
R
/P  
R
HDMI  
S-VIDEO  
INPUT  
NPUT  
3
3
Color-1  
Color-2  
Color-3  
Digital Component Video signals (4:2:2)  
locked  
HDMI cable  
(commercially available)  
Digital Component Video signals (4:4:4)  
locked  
Audio cable  
Digital RGB signals locked  
(commercially available)  
Make this connection  
when inputting analog  
audio signals.  
Press HOME MENU to exit the menu.  
6
• If you select a parameter other than “Auto”, make such a setting that  
results in natural color.  
• If no image appears, specify another digital video signal type.  
• For the digital video signal types to be specified, check the operation  
manual that came with the connected equipment.  
HDMI equipment  
To specify the type of audio signals:  
Press HOME MENU.  
1
2
3
4
5
Select “Option”. (  
Select “HDMI Input”. (  
Select “Audio”. ( then ENTER)  
Select the type of audio signals. (  
/
then ENTER)  
/
then ENTER)  
/
/
then ENTER)  
• If you select “Auto”, an attempt will be made to identify  
the type of audio signals when audio signals are  
received.  
51  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Enjoying through External Equipment  
Item  
Auto  
Description  
Automatically identifies input audio  
• The INPUT 4 terminals are checked for cable connections in the  
order where; 1) Component Video, 2) S-Video, 3) Video.  
• Connect external equipment to only terminals that are to be actually  
used.  
(factory default) signals.  
Digital  
Analog  
Accepts digital audio signals.  
Accepts analog audio signals.  
Displaying an image of the game console or  
Press HOME MENU to exit the menu.  
6
camcorder  
To watch an image coming from the game console or  
camcorder, press INPUT 4 on the remote control unit or press  
INPUT on the Plasma Display to select INPUT4.  
• If no sound is output, specify another audio signal type.  
• For the audio signal types to be specified, check the operation  
manual that came with the connected equipment.  
• Depending on the equipment to be connected, you also need to  
connect analog audio cables.  
Recording digital TV programs using a  
VCR or DVD recorder  
If you connect recording equipment such as a VCR or DVD  
recorder to the MONITOR OUT terminals on the rear of the  
Media Receiver, you can record, for example, digital TV  
programs using the recording equipment.  
Enjoying a game console or watching  
camcorder images  
You can also record digital TV programs more easily by using  
the supplied VCR controller. Connect the VCR controller to the  
VCR control terminal on the rear of the Media Receiver and  
then position the controller so that its light emitting section  
faces the remote control sensor on the recording equipment.  
For more information, see page 59.  
Connecting a game console or camcorder  
Use the INPUT 4 terminals to connect a game console,  
camcorder and other audiovisual equipment.  
Media Receiver (front view)  
Avoiding unwanted feedback  
You can prevent unwanted feedback from adversely affecting  
the quality of images. Specify the output terminal whose output  
is to be inhibited.  
INPUT  
4
PC  
AUDIO  
STEREO  
COMPONENT VIDEO  
CB / PB CR / PR  
S
-VIDEO  
VIDEO  
AUDIO  
ANALOG RGB  
(
)
Y
L
R
Press HOME MENU.  
1
2
3
4
Select “Option”. (  
Select “Monitor Out”. (  
Select “INPUT1 Prohibit”, “INPUT2 Prohibit”, “INPUT3  
Prohibit”, or “INPUT4 Prohibit”. ( then ENTER)  
Press HOME MENU to exit the menu.  
/
then ENTER)  
/
then ENTER)  
AV cable  
(commercially available)  
/
5
S-Video cable  
(commercially available)  
Component Video cable  
(commercially available)  
Game console/Camcorder  
52  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying through External Equipment  
12  
Connecting a recorder  
Connecting other audio equipment  
The digital audio output terminal (optical) on this system can  
output Dolby Digital signals. Using an optical digital cable,  
connect an AV receiver to the digital audio output terminal  
(optical) on the rear of the Media Receiver. This allows audio  
such as digital TV broadcasting to be played in high quality.  
Media Receiver (rear view)  
DIGITAL OUT  
OPTICAL  
If your AV receiver does not have a digital audio input terminal  
(optical), connect the MONITOR OUT terminals (AUDIO) on the  
rear of the Media Receiver to the audio input terminals on the  
AV receiver.  
I N  
CONTROL  
ANTENNA  
OUT  
VCR CONTROL  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
IN  
B
S400  
(TS)  
S-VIDEO INPUT  
2
INPUT  
1
COMPONENT VIDEO  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
SERVICE ONLY  
OUT  
INPUT  
1
VIDEO  
R-AUDIO-L  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
HDM  
MONITOR OUT S-VIDEO  
S-VIDEO  
INPUT  
INPUT  
3
3
• When using the digital audio output terminal (optical), you need to  
make settings depending on your AV receiver. For more information,  
see the instruction manual that came with the AV receiver.  
AV cable  
(commercially available)  
Connecting an AV receiver  
S-Video cable  
(commercially available)  
Media Receiver (rear view)  
VCR controller (for  
DIGITOUT  
OPAL  
presetting digital TV  
I N  
CONTROL  
ANTENNA  
OUT  
VCR CONTROL  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
IN  
programs for recording)  
B
S400  
(TS)  
S-VIDEO INPUT  
2
INPUT 1 COMPONENT VIDEO  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
SERVICE ONLY  
OUT  
INPUT  
1
H
MONITOR OUT  
VIDEO  
R-AUDIOL  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
S-VIDEO  
S-VIDEO  
INPUT  
3
Audio cable  
(commercially available)  
VCR or DVD recorder  
Optical digital cable  
(commercially available)  
• About the MONITOR OUT terminals  
The MONITOR OUT terminals cannot output the following signals:  
1 Video signals input from the COMPONENT VIDEO terminal  
2 Video signals from a personal computer  
3 S-Video signals when a conventional TV channel is being received  
4 S-Video signals when Video signals (INPUT 1, 2, and 4) are being  
input  
AV receiver  
5 Digital video and audio signals from the HDMI terminals  
• When watching images played back on a VCR or DVD recorder  
connected to the MONITOR OUT terminals, select an input source  
(e.g., TV channel reception) on the recording equipment other than  
external input sources. Selecting an external input source may result  
in distorted images or noise.  
• Analog broadcasting signals are not sent to the MONITOR OUT  
(S-VIDEO) terminal. This is also true of composite signals coming  
from INPUT 1, 2, or 4.  
53  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Enjoying through External Equipment  
Switching the optical audio signal type  
Set up for the DIGITAL AUDIO output terminal (OPTICAL),  
depending on your AV receiver.  
When connecting a single D-VHS recorder  
Media Receiver (rear view)  
Press HOME MENU.  
1
2
3
4
DIGITAL OUT  
OPTICAL  
Select “Option”. (  
Select “Digital Audio Out”. (  
Select “Dolby Digital” or “PCM”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
CR CONTROL  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
IN  
S400  
/
(TS)  
S-VIDEO INPUT  
2
INPUT  
1
COMPONENT VIDEO  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
/
Item  
Description  
OUT  
INPUT  
1
IN  
HDMI  
ITOR OUT  
VIDEO  
R-AUDIO-L  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
S-VIDEO  
S-VIDEO  
INPUT  
3
PCM  
Always outputs in the PCM format  
(factory default) regardless of the types of signals.  
(The function and performance  
are the same for both terminals.)  
Dolby Digital  
For Dolby Digital encoded signals, outputs in  
the Dolby Digital format. For PCM encoded  
signals, outputs in the PCM format.  
i.LINK cable  
(commercially available)  
Press HOME MENU to exit the menu.  
5
To use i.LINK, you need to  
connect only an i.LINK cable;  
you need not connect cables to  
the video and audio terminals.  
Watching a D-VHS image  
What is i.LINK?  
i.LINK is a digital serial interface for handling digital video,  
digital audio, and other data in two directions. i.LINK is Sony’s  
term for the IEEE 1394 data transport bus. Digital AV equipment  
compatible with i.LINK can be connected using a single i.LINK  
cable. The i.LINK interface allows this PDP system to control  
one of up to two i.LINK compatible devices (in connection) that  
can be identified.  
D-VHS recorder  
Which i.LINK devices are connectable?  
For i.LINK devices, this system supports only D-VHS recorders.  
The i.LINK terminals on this system cannot be connected with  
other equipment such as DVD recorders, digital video cameras,  
personal computers, and PC peripheral devices because of  
differences in the specifications.  
When connecting two D-VHS recorders  
You can connect two D-VHS recorders directly to the i.LINK  
terminals on the rear of the Media Receiver.  
i.LINK cables  
Media Receiver  
D-VHS recorder  
D-VHS recorder  
What can be recorded through i.LINK?  
With D-VHS recorders connected to this system through i.LINK,  
you can record only digital TV programs. You cannot record  
conventional TV channels nor contents coming from external  
input sources and personal computers.  
POWER  
REC  
DATA  
ON  
STANDBY  
TIMER  
ACQUISITION  
Connecting D-VHS recorders  
Use the i.LINK terminals when connecting D-VHS recorders.  
54  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying through External Equipment  
12  
Using i.LINK cables you can also connect up to two  
D-VHS recorders in a daisy chain.  
Displaying a D-VHS image  
To watch a D-VHS image, press i.LINK on the remote control  
unit or press INPUT on the Plasma Display to select i.LINK.  
i.LINK cable  
Media Receiver  
D-VHS recorder  
Useful and important notification  
POWER  
REC  
DATA  
ON  
STANDBY  
TIMER  
ACQUISITION  
Useful information  
• D-VHS recorders connected through i.LINK can play back  
digital TV programs recorded using this system.  
• D-VHS recorders connected through i.LINK can record only  
digital TV programs. Using i.LINK, those recorders cannot  
record conventional TV channels nor contents coming from  
external input sources.  
D-VHS recorder  
• This system can be simultaneously connected with up to two  
D-VHS recorders that support i.LINK. You can control one of  
these D-VHS recorders (basic functions only).  
Precautions about i.LINK connections  
• Use S400 i.LINK cables that have 4-pin plugs and are shorter  
than 3.5 m (11.48 feet).  
• Some D-VHS recorders connected through i.LINK may not  
allow this system to control through the control panel screen  
or to display images and output sound.  
• Some i.LINK devices cannot relay data when their power is  
off.  
• To record digital TV programs using connected D-VHS  
recorders, use D-VHS tape. You cannot use VHS tape nor  
S-VHS tape.  
• Do not make the following loop connections:  
• Some D-VHS recorders connected though i.LINK may not  
allow this system to play back images and sound recorded on  
VHS tape, S-VHS tape, or (if with analog signals) D-VHS tape.  
If this is the case, connect the analog output terminals on the  
D-VHS recorder to INPUT 1, 2, 3, or 4 terminals on this  
system. See page 50.  
Media Receiver  
D-VHS recorder  
POWER  
REC  
DATA  
ON  
STANDBY  
TIMER  
ACQUISITION  
• This system supports the Digital Transmission Content  
Protection (DTCP) technology. The DTCP is a copy protection  
technology that presents data coding and device  
authentication.  
D-VHS recorder  
D-VHS recorder  
• i.LINK may not allow copy-restricted video, audio, and other  
data to be copied from one i.LINK device to another. It also  
may not allow video, audio, and other data to be transferred  
with equipment that does not support the DTCP.  
Media Receiver  
POWER  
REC  
DATA  
ON  
STANDBY  
TIMER  
ACQUISITION  
Precautions  
• While one D-VHS recorder connected through i.LINK is  
recording or playing back, do not switch on or off the other  
connected D-VHS recorder (not in use) or do not connect or  
disconnect the i.LINK cable from that D-VHS recorder. Doing  
so can result in image and sound interruption.  
• Some D-VHS recorders that support i.LINK cannot relay data  
when their power is off. Check the instruction manual that  
came with your D-VHS recorder. This system allows you to  
change the setting for data relay in the standby mode. See  
“Setting up for i.LINK standby” on page 57.  
55  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Enjoying through External Equipment  
Setting up for controlling a D-VHS recorder  
You can operate the connected D-VHS recorder from the  
Plasma Display that shows the control panel screen. After  
making the connections, use the menu to specify the model of  
the D-VHS recorder to be operated. You can operate only a  
single D-VHS recorder from the Plasma Display.  
Editing the i.LINK list  
The i.LINK list shows all devices connected through i.LINK  
interfaces. In this list, you can change the name or order of  
devices or delete device information.  
Press HOME MENU.  
1
2
3
4
5
6
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
then ENTER)  
Select the desired device. (  
Press HOME MENU.  
1
2
3
4
5
6
Select “Recorder Setup”. (  
Select “i.LINK Setup”. (  
Select “i.LINK List”. (  
/
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
then ENTER)  
Select the D-VHS recorder model to be operated.  
/
Select “Recorder Setup”. (  
Select “i.LINK Setup”. (  
Select “i.LINK List”. (  
/
/
/
/
)
/
Recorder Setup i.LINK Setup  
i.LINK Setup i.LINK List  
i.LINK List  
(
/
then ENTER)  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
D-VHS XXXX XXXX Control  
---  
---  
Recorder Setup i.LINK Setup  
i.LINK Setup i.LINK List  
i.LINK List  
A
B
C
D
Connect  
Rename  
Move  
Delete  
Home Menu  
Exit  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
D-VHS XXXX XXXX Control  
---  
---  
Delete  
The following procedure differs depending on what you want to  
perform.  
A
B
C
D
Connect  
Rename  
Move  
Home Menu  
Exit  
Press A to select “Connect”.  
7
8
To change the name of a device:  
Press HOME MENU to exit the menu.  
Press B to select “Rename”.  
7
8
Enter up to 7 characters using  
/
,
/
, and ENTER.  
• The following information appears at the right end of the i.LINK list to  
indicate the connection status of the D-VHS recorders:  
Recorder Setup i.LINK Setup  
i.LINK Setup i.LINK List  
i.LINK List  
New Name: D-VHS  
Control:  
Data connection with the D-VHS recorder has been  
established and the recorder is ready for control.  
A
K
U
5
)
B
L
V
6
,
C
M
W
7
D
N
X
8
E
O
Y
9
:
F
P
Z
0
'
G
Q
1
.
H
R
2
I
J
T
4
(
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
S
3
/
@
–
_
&
S P A C E  
Link:  
The D-VHS recorder has been physically con-  
nected, and can be controlled if it is selected for  
control.  
A
B
D
Home Menu  
Exit  
Accept  
Clear  
Cancel  
—:  
Currently not physically connected  
Press A.  
9
10  
• When connected to any device other than a D-VHS, the device is not  
listed in the i.LINK List.  
Press HOME MENU to exit the menu.  
To change the order of devices:  
Press C to select “Move”.  
7
8
Select the new desired position. (  
• The selected device is moved to the selected position.  
/
then ENTER)  
Press HOME MENU to exit the menu.  
9
To delete information about a device:  
Press D to select “Delete”.  
• A confirmation message appears.  
7
• A warning message appears if the selected device has  
been preset for recording with the timer or if its power  
is on. If this is the case, you cannot delete the device  
that you have selected.  
Press A to execute the deletion.  
8
9
Press HOME MENU to exit the menu.  
56  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying through External Equipment  
12  
Setting up for i.LINK standby  
Use the following procedure to enable data transfer between  
multiple i.LINK devices even when the system is in the standby  
mode.  
Operating the control panel screen  
The control panel screen appears when you press i.LINK. It  
disappears when you press i.LINK again. To select a button on  
the control panel screen, press  
ENTER on the remote control.  
/
6 7  
D
or  
/
, and then press  
Press HOME MENU.  
1
2
3
4
5
6
7
Select “Tuner Setup”. (  
/
then ENTER)  
then ENTER)  
then ENTER)  
then ENTER)  
then ENTER)  
Press HOME MENU to exit the menu.  
1
2
3
4
5
8
9
20  
Select “Recorder Setup”. (  
Select “i.LINK Setup”. (  
Select “i.LINK Standby”. (  
Select “Enable”. (  
/
/
D-VHS4  
XXXXXXX XXX  
Device List  
• D-VHS4  
/
No1394 00:00:00  
ON/OFF  
REC  
/
A
i.LINK Setup  
• With “Enable” selected, the system relays data between multiple  
i.LINK devices even when in the standby mode; the i.LINK circuits  
are energized in that mode.  
10  
11 12 13  
14 15 16 17 18  
19  
1
2
3
4
Shows the current status of the D-VHS recorder.  
Shows the name of the currently selected device.  
Shows counter time output by the D-VHS recorder.  
Shows the manufacture name of the D-VHS recorder to be  
operated.  
In standby mode  
i.LINK device  
Media Receiver i.LINK device  
POWER  
REC  
DATA  
ON  
STANDBY  
TIMER  
ACQUISITION  
5
6
Shows the model name of the D-VHS recorder to be  
operated.  
Shows the type of inserted video tape; D for D-VHS, S for  
S-VHS, and no display for VHS.  
No data relay  
7
8
Appears when any tape has been inserted.  
Appears when the inserted tape has been write protected.  
The inserted tape cannot be used for recording when this  
indicator appears.  
9
Appears when the D-VHS recorder has been preset for  
recording and is in the standby mode.  
10 Switches on and off the D-VHS recorder.  
11 Starts recording.  
12 Rewinds to the start of the current program.  
13 Rewinds the tape.  
14 Pauses the tape.  
15 Stops the current tape motion.  
16 Starts playing back.  
17 Forwards to the start of the next program.  
18 Forwards the tape.  
19 Exits the control panel screen and displays the i.LINK Setup  
menu.  
20 Allows you to change the D-VHS recorder to be operated.  
After pressing this button, press  
/
to select the desired  
model from the list, and then press ENTER.  
• If no i.LINK device has been connected, “No i.LINK devices are  
connected.” appears. If this is the case, connect i.LINK devices.  
• If none of the connected equipment has been supported for control,  
you cannot execute control.  
57  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Enjoying through External Equipment  
Signal names for 15-pin mini D-sub connecter  
Watching an image from a personal  
computer  
5
4
3
2
1
10  
9
8
7
6
15  
14  
13  
12  
11  
Connecting a personal computer  
Use the PC terminals to connect a personal computer.  
(front view)  
Pin No.  
Signal name  
• The PC input terminals are DDC2B-compatible.  
• Plug & Play may not correctly function, depending on personal  
computers in use.  
1
2
3
4
R
G
B
Not connected  
Media Receiver (front view)  
5
Not connected  
6
7
8
GND (ground)  
GND (ground)  
GND (ground)  
INPUT  
4
PC  
AUDIO  
STEREO  
EC  
ER  
DATA  
ACQUISITION  
COMPONENT VIDEO  
CB / PB CR / PR  
S
-VIDEO  
VIDEO  
AUDIO  
ANALOG RGB  
(
)
Y
L
R
9
+5V  
10  
11  
12  
13  
14  
15  
GND (ground)  
Not connected  
SDA  
HD  
VD  
ø 3.5 mm stereo mini-  
plug cable  
(commercially available)  
SCL  
RGB cable  
(commercially available)  
• A Macintosh adaptor may be required for use with some Macintosh  
computers.  
Computer compatibility chart  
Resolution  
Frequency  
Remarks  
Macintosh 13" (67 Hz)  
Personal computer  
720 × 400  
70 Hz  
640 × 480  
60 Hz  
65 Hz  
72 Hz  
75 Hz  
56 Hz  
60 Hz  
72 Hz  
75 Hz  
74.5 Hz  
60 Hz  
70 Hz  
75 Hz  
56 Hz  
60 Hz  
70 Hz  
Displaying an image from a personal computer  
When connecting to a personal computer, the input signal type  
is automatically identified. If the personal computer image does  
not come in clearly, you may need to use Auto Setup in the  
menu. See page 45.  
To watch an image coming from the personal computer, press  
PC on the remote control unit or press INPUT on the Plasma  
Display to select “PC”.  
800 × 600  
832 × 624  
Macintosh 16"  
Macintosh 19"  
• The PC terminals cannot be used for audiovisual equipment.  
1024 × 768  
1280 × 768  
58  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying through External Equipment  
Connecting the VCR controller  
12  
Use the following procedure to set the manufacture of the  
recording equipment:  
Connect the supplied VCR controller to the Media Receiver. This  
allows you to preset digital TV programs for recording; see page  
48. When the specified time comes, the system in the standby  
mode is automatically switched on and the specified TV  
Press HOME MENU.  
1
2
3
4
5
Select “Tuner Setup”. (  
/
then ENTER)  
Select “Recorder Setup”. (  
Select “VCR Setup”. (  
/
then ENTER)  
program is recorded using the connected VCR or DVD recorder.  
/
then ENTER)  
Select the manufacture of the recording equipment.  
then ENTER)  
(
/
• Make sure to leave the VCR power on when presetting TV programs  
for recording with the VCR controller.  
• Be sure to firmly connect the VCR controller to the VCR control  
terminal on the rear of the Media Receiver. If you have mistakenly  
connected it to the CONTROL IN or CONTROL OUT terminal, remote  
control or other operations may be disabled.  
Recorder Setup  
VCR Setup  
VCR Setup  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
xxxxxxxxxxxxxxxxxxxxx  
• XXXXX  
XXXXX  
XXXXX  
Home Menu  
Exit  
Media Receiver (rear view)  
• The screen for recording test appears.  
DIGITAL  
OPTICA  
O
Check that the power to the recording equipment is on,  
and insert tape into the slot.  
• Insert tape you think it all right to erase its contents.  
The contents will be erased because Rec and Stop  
codes are output in the test.  
• Check that the light emitting section on the VCR  
controller cable faces the recording equipment.  
6
7
I N  
CONTROL  
ANTENNA  
OUT  
VCR CONTROL  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
IN  
B
S400  
(TS)  
S-VIDEO INPUT  
2
INPUT  
1
COMPON  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
Y
C
B
SERVICE ONLY  
OUT  
VIDEO  
R-AUDIO-L  
R-AUDIO-L  
Y
C
B
MONITOR OUT  
S-VIDEO  
S-VIDEO  
INPUT  
INPUT  
3
3
(Once you have positioned the  
VCR controller, secure with the  
supplied tape.)  
Press A to execute recording test.  
• If the recording equipment fails to start and stop  
recording, check and change the specified recording  
equipment manufacture.  
VCR CONTROL  
Press A to select “Yes, Store Setting”.  
8
9
.
Press HOME MENU to exit the menu.  
VCR or DVD  
recorder  
Position the light  
emitting section  
on the VCR  
controller cable  
so that it faces  
the VCR.  
• Even if you correctly specify the manufacture of the recording  
equipment, control of some models may be disabled.  
• Perform the recording test when the recording equipment is not in  
recording standby or is not recording.  
• The recording test takes approximately 10 seconds.  
• The PIONEER has been set as the factory default.  
Remote control sensor  
59  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Enjoying through External Equipment  
The lists of controllable recording  
equipment manufactures  
Manufacture  
Manufacture  
Manufacture  
Manufacture  
Admiral  
Harley Davidson  
Philco  
Toshiba  
Advantz  
Adventura  
Aiko  
Harman/Kardon  
Harwood  
Headquarter  
Hitachi  
Philips  
Pilot  
Totevision  
Unitech  
Pioneer  
Portland  
Profitronic  
Proscan  
Protec  
Pulsar  
Vector  
Aiwa  
Vector Research  
Video Concepts  
Videosonic  
Wards  
Akai  
JVC  
American High  
Asha  
Jensen  
KEC  
Audiovox  
Beaumark  
Bell & Howell  
Broksonic  
CCE  
KLH  
White Westinghouse  
XR-1000  
Kenwood  
Quarter  
Quartz  
Quasar  
RCA  
Kodak  
Yamaha  
LXI  
Zenith  
Lloyd's  
Some modes of the listed  
manufactures may not allow  
control through the VCR  
controller.  
Calix  
Logik  
Radio Shack  
Radix  
Canon  
MEI  
Capehart  
MGA  
Randex  
Realistic  
Ricoh  
Carver  
MGN Technology  
MTC  
Cineral  
Citizen  
Magnasonic  
Magnavox  
Magnin  
Marantz  
Marta  
Runco  
STS  
Colt  
Craig  
Salora  
Curtis Mathes  
Cybernex  
Daewoo  
Daytron  
Denon  
Samsung  
Sanky  
Matsushita  
Memorex  
Minolta  
Mitsubishi  
Motorola  
Multitech  
NAD  
Sansui  
Sanyo  
Scott  
Dynatech  
Electrohome  
Electrophonic  
Emerex  
Sears  
Semp  
Sharp  
Shintom  
Shogun  
Singer  
Sony  
Emerson  
Fisher  
NEC  
Nikko  
Fuji  
Nikon  
Funai  
Noblex  
Olympus  
Optimus  
Optonica  
Orion  
Sylvania  
Symphonic  
TMK  
GE  
Garrard  
Go Video  
GoldStar  
Gradiente  
Grundig  
HI-Q  
Tatung  
Teac  
Panasonic  
Penney  
Pentax  
Technics  
Teknika  
Thomas  
60  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Enjoying through External Equipment  
12  
Media Receiver (rear view)  
Connecting control cords  
DIGITAL OUT  
OPTICAL  
Connect control cords between the Media Receiver and other  
I
N
OUT  
CONTROL  
ANTENNA  
VCR CONTROL  
ANTENNA/  
CABLE IN  
Cable  
CARD  
A
PIONEER equipment having the  
logo. You can then operate  
IN  
B
S400  
(TS)  
the connected equipment by sending commands from its  
remote control unit to the remote control sensor on the Media  
Receiver.  
S-VIDEO INPUT  
2
INPUT  
1
COMPONENT VIDEO  
VIDEO  
R-AUDIO-L  
VIDEO  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
SERVICE ONLY  
OUT  
INPUT  
1
INPUT  
3
R-AUDIO-L  
R-AUDIO-L  
Y
C
B
/P  
B
C
R
/P  
R
HDMI  
MONITOR OUT  
VIDEO  
S-VIDEO  
S-VIDEO  
INPUT  
INPUT  
3
3
After the CONTROL IN terminals have been connected, the  
remote control sensors on the connected equipment do not  
accept commands from the remote control units. Face the  
remote control units to the remote control sensor on the  
Plasma Display when operating the connected equipment.  
I N  
CONTROL  
OUT  
• Make sure that the power is turned off when making connections.  
• Complete all component connections before making control cord  
connections.  
CONTROL  
IN  
OUT  
About SR+  
The CONTROL OUT terminal on the rear of the Media Receiver  
supports SR+ that allows linked operations with a PIONEER  
AV receiver. SR+ presents functions such as the input switch  
linkage operation function and the DSP surround mode display  
function. For more information, see the instruction manual that  
came with the PIONEER AV receiver supporting SR+.  
CONTROL  
IN  
OUT  
• While in connection through SR+, the volume on this system is  
temporarily minimized.  
CONTROL  
IN  
OUT  
The control cables (commercially available) are mono sound  
cables with mini plugs (no resistance).  
61  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Useful Remote Control Features  
Presetting manufacture codes  
Learning function of the remote control  
unit  
Slide the Mode switch to match the device to which you  
1
2
3
want to preset the remote control signal.  
You can operate the connected AV products (AV Receiver, Cable  
Box, SAT tuner, VCR, DVD, DVD recorder, LD) using the learning  
function of your remote control unit. This remote control unit  
has a function that can memorize each remote control code.  
Press EDIT/LEARN and 1 at the same time.  
• The LED flashes.  
Press 0 – 9 to enter the manufacture code. See page 63.  
• Preset mode is finished once the LED no longer lights  
up.  
2 to 5 cm (0.8 to 2.0 inches)  
• To exit the Edit mode halfway, press EDIT/LEARN again.  
• If the Mode switch selection is changed when in the Edit mode, the  
Edit mode is cancelled.  
• If no operation is performed for more than one minute, the Edit mode  
is cancelled.  
• When you enter a code not listed, the LED flashes quickly.  
• If the table on page 63 does not include your desired manufacturer or  
the remote control does not work, you can make the memory learn  
its signal by the Learn mode.  
Remote control  
(Supplied accessory)  
Remote control of  
AV product  
• The initial mode is “000” (PIONEER).  
Using the learning function  
Slide the Mode switch to match the device whose remote  
control signal you want to be learned.  
1
2
3
Press EDIT/LEARN and 2 at the same time.  
•The LED flashes.  
Press a button to be learned.  
• The LED lights up.  
• For the functions that can be learned, see pages 64 to  
68.  
• When learning is finished, the LED starts flashing  
again.  
Press EDIT/LEARN again to exit the Learn mode.  
4
• To exit the Learn mode halfway, press EDIT/LEARN again.  
• If the Mode switch selection is changed when in the Learn mode,  
the Learn mode is cancelled.  
• If no operation is performed for more than one minute, the Learn  
mode is cancelled.  
• It takes about 2 seconds to finish code transmission. Do not interrupt  
it halfway. Wait until the LED flashes again.  
• You can reset all learned codes to the factory defaults. When not in  
the Learn mode, press and hold TV , and then press  
and  
VOL + (RECEIVER section) at the same time.  
62  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Useful Remote Control Features  
13  
Manufacture codes  
CABLE/SAT  
VCR  
DVD/DVR  
CABLE/SAT  
VCR  
DVD/DVR  
000  
001  
002  
003  
004  
005  
006  
007  
008  
009  
010  
011  
PIONEER1(CABLE)  
PIONEER2(CABLE)  
JERROLD1(CABLE)  
JERROLD2(CABLE)  
JERROLD3(CABLE)  
JERROLD4(CABLE)  
JERROLD5(CABLE)  
JERROLD6(CABLE)  
JERROLD7(CABLE)  
JERROLD8(CABLE)  
JERROLD9(CABLE)  
JERROLD10(CABLE)  
S.A.1(CABLE)  
PIONEER  
FISHER  
PIONEER(DVD)  
053  
054  
055  
056  
057  
058  
059  
060  
061  
062  
063  
064  
065  
066  
067  
068  
069  
070  
071  
072  
073  
074  
075  
076  
077  
078  
079  
080  
081  
082  
083  
084  
085  
086  
087  
088  
089  
090  
091  
092  
093  
094  
095  
096  
097  
098  
099  
10 0  
101  
102  
103  
104  
Grundig1  
Grundig2  
Grundig3  
SONY2  
PANASONIC(DVD)  
FISHER2  
SAMSUNG(DVD)  
FISHER3  
SONY(DVD)  
GOLDSTAR  
HITACHI  
TOSHIBA(DVD)  
SONY3  
JVC(DVD)  
SONY4  
HITACHI2  
HITACHI3  
MAGNAVOX2  
MITSUBISHI  
MITSUBISHI2  
MITSUBISHI3  
MITSUBISHI4  
MITSUBISHI5  
MITSUBISHI6  
PANASONIC  
PANASONIC2  
PANASONIC3  
RCA  
PIONEER(DVD-RECORDER)  
PIONEER2(DVD-RECORDER)  
PIONEER3(DVD-RECORDER)  
PANASONIC(DVD-RECORDER)  
PANASONIC2(DVD-RECORDER)  
PANASONIC3(DVD-RECORDER)  
PHILIPS(DVD-RECORDER)  
SHARP(DVD-RECORDER)  
SHARP2(DVD-RECORDER)  
TOSHIBA(DVD-RECORDER)  
TOSHIBA2(DVD-RECORDER)  
RCA4  
PHILIPS  
PHILIPS2  
PHILIPS3  
PHILIPS4  
PHILIPS5  
PHILIPS6  
SAMSUNG  
SAMSUNG2  
SAMSUNG3  
SAMSUNG4  
SAMSUNG5  
SAMSUNG6  
MARANTZ  
MARANTZ2  
GE  
012  
013  
S.A.2(CABLE)  
014  
015  
S.A.3(CABLE)  
S.A.4(CABLE)  
016  
ZENITH1(CABLE)  
ZENITH2(CABLE)  
ZENITH3(CABLE)  
017  
018  
019  
020  
021  
022  
023  
024  
025  
026  
027  
028  
029  
030  
031  
032  
033  
034  
035  
036  
037  
038  
039  
040  
041  
042  
043  
044  
045  
046  
047  
048  
049  
050  
051  
052  
RCA2  
PIONEER(SAT)  
RCA1(SAT)  
RCA2(SAT)  
SONY(SAT)  
RCA3  
PIONEER(LD)  
KENWOOD(LD)  
PANASONIC1(LD)  
PANASONIC2(LD)  
PHILIPS(LD)  
SANYO  
SANYO2  
SANYO3  
SHARP  
GE2  
GE3  
YAMAHA  
SHARP2  
RCA(LD)  
YAMAHA2  
YAMAHA3  
YAMAHA4  
CURTIS_MATHIS  
CURTIS_MATHIS2  
CURTIS_MATHIS3  
FUNAI  
SHARP3  
SONY(MDP)  
SONY(LD)  
SONY(BETA)  
SONY(VHS)  
SONY(8mm)  
TOSHIBA  
JVC  
JVC2  
ADMIRAL  
KENWOOD  
KENWOOD2  
KENWOOD3  
NEC  
JVC3  
JVC4  
JVC5  
ZENITH  
MITSUBISHI(J-3)  
SHARP(J-2)  
PANASONIC(J-3)  
TOSHIBA(J-3)  
GRANDIENTE  
AKAI  
NEC2  
NEC3  
NEC4  
WARDS  
WARDS2  
WARDS3  
WARDS4  
MEMOREX  
MEMOREX2  
JC_PENNY  
JC_PENNY2  
JC_PENNY3  
JC_PENNY4  
JC_PENNY5  
JC_PENNY6  
PIONEER2  
SANYO4  
MATSUI  
AIWA  
ALBA81  
BUSH  
THOMSON  
BAIRD  
TELEFUNKEN  
ALBA  
63  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Useful Remote Control Features  
Receiver control buttons  
When a Pioneer receiver is connected to the display, the  
receiver can be operated using buttons 1 to 3.  
Using the remote control unit to control  
other devices  
When a non-Pioneer receiver is connected to the display, the  
signals for 1 to 3 must first be learned before operating. See  
page 62.  
1
2
3
RECEIVER  
(STANDBY/ON)  
Mode switch  
(with “TV”  
selected)  
Turns the receiver power on and off.  
RECEIVER INPUT  
Selects the input source connected to the receiver.  
RECEIVER VOL +/–  
Adjusts the receiver volume level. Press VOL + to  
increase the volume and VOL – to decrease it.  
• (RECEIVER)  
MUTING  
Allows the remote control unit to learn receiver’s mute signal. Use  
this button when the mode switch is set to a position other than TV.  
• The color-highlighted buttons on the remote control can learn the  
control signal from another device’s remote control.  
1
2
3
64  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Useful Remote Control Features  
13  
Cable control buttons  
When the Mode switch is set to CBL/SAT, the cable converter  
connected to the display can be operated using 1 to 5.  
Cable converters made by other manufacturers and not preset  
can also be operated using the remote control unit if 1 to 5  
have learned the functions. See page 62.  
Mode switch  
(with “CBL/SAT”  
selected)  
1
0 – 9  
Press a button (or buttons) that corresponds to the  
channel that you want to watch.  
1
2
2
CH +/–  
Press CH + or CH – to tune in a higher or lower channel.  
4
5
3
4
SOURCE  
Turns the cable converter power on and off.  
CH ENTER *  
Fix the selected channel with the direct channel selection  
buttons.  
5
CH RETURN *  
Press to switch between the current channel and the  
channel you were watching immediately before.  
* Some manufacturers do not preset CH ENTER and  
CH RETURN. Use these buttons to learn if necessary.  
• CABLE and SAT cannot be selected at the same time.  
• The color-highlighted buttons on the remote control can learn the  
control signal from another device’s remote control.  
3
65  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Useful Remote Control Features  
SAT control buttons  
When the SAT is preset by the learning function of the remote  
control, the remote control unit buttons will function as shown  
below.  
Mode switch  
(with “CBL/SAT”  
selected)  
• When the Mode switch is set to CBL/SAT, satellite broadcast  
tuners made by other manufacturers and not preset can also  
be operated with the remote control unit if 1 to 8 have  
learned the functions. See page 62.  
1
0 – 9  
1
Press a button (or buttons) that corresponds to the  
channel that you wish to watch.  
2
3
CH +/–  
6
Press CH + or CH – to tune in a higher or lower channel.  
ENTER, / / /  
ENTER:  
Press to activate the selected function.  
Press the button to select items on the SAT  
GUIDE screen or SAT MENU screen.  
2
/
/
/
:
7
4
SAT INFO  
When this button is pressed, information on satellite  
broadcasting will appear.  
• Use this button to learn if necessary.  
3
8
4
5
6
SOURCE  
Turns the Satellite broadcast tuner power on and off.  
CH ENTER  
Fix the selected channel with the direct channel selection  
buttons.  
• Use this button to learn if necessary.  
7
8
SAT MENU  
5
When this button is pressed, the satellite broadcasting  
menu screen will appear.  
SAT GUIDE  
When this button is pressed, the satellite broadcasting  
guide screen will appear.  
• CABLE and SAT cannot be selected at the same time.  
• The color-highlighted buttons on the remote control can learn the  
control signal from another device’s remote control.  
66  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Useful Remote Control Features  
13  
VCR control buttons  
When the VCR is preset by the learning function of the remote  
control, the remote control unit buttons will function as follows  
when the Mode switch of the remote control unit is set to  
VCR.  
Mode switch  
(with “VCR”  
selected)  
• When the input selector button having the same number as  
the input terminal connecting the VCR is pressed, the VCR  
can be operated using 1 to 8.  
• VCR made by other manufacturers and not preset can also  
be operated using the remote control unit if 1 to 8 have  
learned the functions. See page 62.  
1 CH +/–  
Press to select the channel of the TV tuner on the VCR.  
2 ꢀ (PLAY)  
Selects playback.  
1
3 ꢁ (REW)  
Rewinds the tape and allows picture search.  
4 SOURCE  
Turns the power of the VCR on and off.  
5 ꢂ (PAUSE/STILL)  
Sets pauses and still pictures.  
6 ꢃ (FF)  
Rapidly advances the tape and allows picture search.  
7 ì (REC)  
2
3
4
5
Starts recording.  
6
7
8
8 ꢄ (STOP)  
Stop tape transport.  
• The color-highlighted buttons on the remote control can learn the  
control signal from another device’s remote control.  
67  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Useful Remote Control Features  
1
2
CH +/– (DVD recorder only)  
Press to change the channel of the tuner built in the DVD  
recorder.  
RETURN  
Mode switch  
(with “DVD/  
DVR” selected)  
When the DVD menu is in display, press to restore the  
immediately previous screen.  
3 ꢀ (PLAY)  
Selects playback.  
4 ꢁ (SCAN)/ꢅ (CHAPTER SEARCH)  
Continue pressing to go backward.  
Pressing quickly once takes you to the start of the chapter  
currently playing. Each time you press it, you move back  
to the start of the previous chapter.  
5
SOURCE  
Turns the power of the DVD player or DVD recorder on  
and off.  
1
6 ꢂ (PAUSE/STILL)  
7
8
2
Sets pauses and still pictures.  
7
8
SAT/DVD MENU (DVD, DVD recorder)  
When this button is pressed, the DVD menu will appear.  
ENTER, / / / (DVD, DVD recorder)  
9
ENTER:  
Press to activate the selected function.  
Press the button to select items on the DVD  
MENU screen.  
/
/
/
:
3
9
DVD TOP MENU (DVD, DVD recorder)  
When this button is pressed, the DVD top menu will  
appear.  
10  
11  
12  
4
5
6
10 ꢃ (SCAN)/ꢆ (CHAPTER SEARCH)  
Continue pressing for fast forward.  
Pressing quickly once takes you to the start of the next  
chapter. Each time you press it, you move ahead to the  
start of the next chapter.  
11 ì (REC)  
Starts recording.  
12 ꢄ (STOP)  
Playback stops when pressing once.  
With some DVD players or DVD recorders, pressing the  
button twice may open the disc tray.  
11, 12 REC STOP  
Press and hold ì, and then press this button to stop  
recording. This operation is true of only Pioneer DVD  
recorders.  
DVD/DVR control buttons  
When the DVD/DVR is preset by the learning function of the  
remote control, the remote control unit buttons will function as  
follows when the Mode switch of the remote control unit is set  
to DVD/DVR.  
• The DVD player or DVD recorder cannot be selected at the same  
time.  
• The color-highlighted buttons on the remote control can learn the  
control signal from another device’s remote control.  
• When the input selector button having the same number as  
the input terminal connecting a DVD player or DVD recorder  
is pressed, these players can be operated using 1 to 12.  
• DVD players or DVD recorders made by other manufacturers  
and not preset can also be operated using the remote control  
unit if 1 to 12 have learned the functions. See page 62.  
68  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
14  
Troubleshooting  
Problem  
Possible Solution  
• Make sure the Plasma Display and the Media Receiver are connected correctly. (See page 18.)  
• No power.  
• Is the power cord disconnected? (See page 23.)  
• Has the main power been turned on? (See page 24.)  
• Check if you pressed TV on the remote control unit. (See page 24.)  
If the indicator on the system lights up red, press TV  
.
• Check if the system cable has been disconnected or almost disconnected? (See page 18.)  
• Green and red rectangles appear on  
the screen alternately.  
• External influences such as lightning, static electricity, etc., may cause improper operation.  
• The system cannot be operated.  
In this case, operate the system after first turning the power of the Plasma Display and the Media  
Receiver, or unplugging the power cord and re-plugging it in after 1or 2 minutes.  
• Is the Mode switch set correctly? Slide it to the TV setting position. (See page 14.)  
• Are batteries inserted with polarity (+, –) aligned? (See page 20.)  
• Remote control unit does not  
operate.  
• Are batteries worn out? (Replace with new batteries.) (See page 20.)  
• Operate the remote control unit while pointing it toward the remote control sensor on the Plasma  
Display. (See page 20.)  
• Are you using it under strong or fluorescent lighting?  
• Is a fluorescent light illuminated near the remote control sensor?  
• Check if the input source for video or PC has been unintentionally selected although you want to  
• No image and audio is presented.  
• No picture.  
watch a TV channel. (See page 25.)  
• Check if you have activated the Parental Control function. (See page 33.)  
Enter a password to temporarily cancel the Parental Control function. (See page 37.)  
• Is connection to other components correct? (See pages 50 to 58.)  
• Is a non-compatible PC signal being input? (See page 58.)  
• Is picture adjustment correct? (See page 41.)  
• Check if you have selected “Picture Off” for Energy Save. With this option selected, the screen is  
deactivated; only audio is output. To restore the screen display, press any button other than  
VOL +/– and MUTING. (See page 44.)  
• Audio is output but no image is  
presented.  
• Check if you have selected the minimum volume. (See page 26.)  
• Check if you have muted sound. (See page 26.)  
• Images are presented but no audio  
is output.  
• When using a video or PC input source, check that the audio terminal is also in connection.  
(See pages 50 to 54 and 58.)  
• Check if the speaker cable connections have been reversed between the right and left or if the  
speaker cable from either speaker has been disconnected. (See pages 12 and 18.)  
• Has the balance been correctly adjusted? (See page 43.)  
• Sound is reversed between the right  
and left.  
• Sound is output from only a single  
speaker.  
• Is the image position correct? (See page 45.)  
• Picture is cut off.  
• Has the correct screen size been selected? (See page 46.)  
• Adjust the picture tone. (See page 41.)  
• Strange color, light color, dark or  
color misalignment.  
• Is the room too bright? The picture may look dark in a room that is too bright.  
• Is the sleep timer set? (See page 40.)  
• Power is suddenly turned off.  
• Panel sounds / noises  
• Check the power control setting. (See page 44.)  
• The system’s internal temperature has increased. Remove any objects blocking vent or clean.  
(See pages 15 and 16.)  
• Panel generated sounds, examples: Fan motor noise, Electrical Circuit Humming / Glass Panel buzzing  
are normal operation of a phosphor-based matrix display.  
Code  
Message  
Check  
SD04  
Powering off. Internal temperature too high.  
Check temperature around PDP.  
Check if the ambient temperature of the Plasma Display is high.  
SD05  
SD11  
Powering off. Internal protection circuits activated,  
Check the speaker cable connections between the Plasma Display  
Is there a short in speaker cable?  
and the speakers.  
Powering off. Internal temperature too high.  
Check if the ambient temperature of the Media Receiver is high.  
Check temperature around media receiver.  
69  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Appendix  
The video program that you watch may be high definition (HD) or standard definition (SD). This Plasma Display is designed to scale  
to each type of definition properly. If the video program’s definition type changes while a menu window is displayed on the screen  
(for example: HD→SD or SD→HD), the menu size may temporarily shrink or enlarge until the scaling is completed. This may  
happen, for example, when you switch between television and an external digital video recorder (D-VHS), or when your recorded  
program switches between different definition types, while the on-screen menu is being shown.  
If this happens, the menu will return to its normal size after two to three seconds. This action is normal, and does not indicate a  
problem with your Plasma Display system.  
70  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
14  
This product in part uses “OpenSSL” software.  
To the extent the OpenSSL software is being used, the following notification applies:  
Copyright (c) 1998-2004 The OpenSSL Project. All rights reserved.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions  
are met:  
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product  
includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”  
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software  
without prior written permission. For written permission, please contact [email protected].  
5. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written  
permission of the OpenSSL Project.  
6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by  
the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”  
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE  
DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,  
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF  
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND  
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)  
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by  
Tim Hudson ([email protected]).  
Original SSLeay License  
Copyright (C) 1995-1998 Eric Young ([email protected])  
All rights reserved.  
This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform  
with Netscapes SSL.  
This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions  
apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation  
included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).  
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a  
product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual  
message at program startup or in documentation (online or textual) provided with the package.  
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions  
are met:  
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.  
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the  
documentation and/or other materials provided with the distribution.  
3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product  
includes cryptographic software written by Eric Young ([email protected])” The word ‘cryptographic’ can be left out if the rouines  
from the library being used are not cryptographic related :-).  
4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an  
acknowledgement: “This product includes software written by Tim Hudson ([email protected])”  
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT  
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN  
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,  
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS  
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN  
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS  
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.  
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code  
cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]  
71  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Appendix  
Linux Source Notice  
The Pioneer Plasma Television integrated with the Media Receiver in part is powered by utilizes the Linux operation system. The  
machine readable copy of the corresponding source code is available for the cost of distribution. To obtain a copy, please visit  
http://www.pioneerelectronics.com/ for more information.  
GNU General Public License  
Version 2, June 1991  
Copyright (C) 1989, 1991 Free Software Foundation, Inc.  
59 Temple Place - Suite 330, Boston, MA 02111-1307, USA  
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.  
Preamble  
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public  
License is intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users.  
This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors  
commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You  
can apply it to your programs, too.  
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that  
you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can  
get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these  
things.  
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights.  
These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.  
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you  
have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their  
rights.  
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy,  
distribute and/or modify the software.  
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free  
software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the  
original, so that any problems introduced by others will not reflect on the original authors’ reputations.  
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program  
will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent  
must be licensed for everyone’s free use or not licensed at all.  
The precise terms and conditions for copying, distribution and modification follow.  
GNU General Public License  
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION  
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed  
under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on  
the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program  
or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included  
without limitation in the term “modification”.) Each licensee is addressed as “you”.  
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of  
running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on  
the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.  
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you  
conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all  
the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this  
License along with the Program.  
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange  
for a fee.  
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and  
distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:  
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.  
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any  
part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.  
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such  
interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a  
notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under  
these conditions, and telling the user how to view a copy of this License.  
72  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
14  
(Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program  
is not required to print an announcement.)  
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program,  
and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to  
those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is  
a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other  
licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.  
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to  
exercise the right to control the distribution of derivative or collective works based on the Program.  
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program)  
on a volume of a storage or distribution medium does not bring the other work under the scope of this License.  
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms  
of Sections 1 and 2 above provided that you also do one of the following:  
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of  
Sections 1 and 2 above on a medium customarily used for software interchange; or,  
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of  
physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed  
under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,  
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is  
allowed only for noncommercial distribution and only if you received the program in object code or executable form with such  
an offer, in accord with Subsection b above.)  
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete  
source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts  
used to control compilation and installation of the executable. However, as a special exception, the source code distributed need  
not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and  
so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.  
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent  
access to copy the source code from the same place counts as distribution of the source code, even though third parties are not  
compelled to copy the source along with the object code.  
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt  
otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this  
License.  
However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as  
such parties remain in full compliance.  
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or  
distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by  
modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so,  
and all its terms and conditions for copying, distributing or modifying the Program or works based on it.  
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the  
original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further  
restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third  
parties to this License.  
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues),  
conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they  
do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations  
under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For  
example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or  
indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of  
the Program.  
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is  
intended to apply and the section as a whole is intended to apply in other circumstances.  
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any  
such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented  
by public license practices. Many people have made generous contributions to the wide range of software distributed through that  
system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute  
software through any other system and a licensee cannot impose that choice.  
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.  
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the  
original copyright holder who places the Program under this License may add an explicit geographical distribution limitation  
excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this  
License incorporates the limitation as if written in the body of this License.  
73  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Appendix  
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new  
versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.  
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to  
it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version  
published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any  
version ever published by the Free Software Foundation.  
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the  
author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation;  
we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives  
of our free software and of promoting the sharing and reuse of software generally.  
NO WARRANTY  
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT  
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER  
PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,  
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE  
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE  
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.  
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR  
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR  
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE  
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER  
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your New Programs  
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make  
it free software which everyone can redistribute and change under these terms.  
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey  
the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.  
<one line to give the program’s name and an idea of what it does.>  
Copyright (C) yyyy name of author  
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published  
by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.  
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.  
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation,  
Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.  
Also add information on how to contact you by electronic and paper mail.  
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:  
Gnomovision version 69, Copyright (C) year name of author  
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to  
redistribute it under certain conditions; type ‘show c’ for details.  
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the  
commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu items—  
whatever suits your program.  
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the  
program, if necessary. Here is a sample; alter the names:  
Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by  
James Hacker.  
signature of Ty Coon, 1 April 1989  
Ty Coon, President of Vice  
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine  
library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the  
GNU Lesser General Public License instead of this License.  
74  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
14  
GNU Lesser General Public License  
Version 2.1, February 1999  
Copyright (C) 1991, 1999 Free Software Foundation, Inc.  
59 Temple Place, Suite 330, Boston, MA 02111-1307, USA  
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.  
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence  
the version number 2.1.]  
Preamble  
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public  
Licenses are intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users.  
This license, the Lesser General Public License, applies to some specially designated software packages—typically libraries—of the  
Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about  
whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations  
below.  
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure  
that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or  
can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you  
can do these things.  
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these  
rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.  
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave  
you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide  
complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling  
it. And you must show them these terms so they know their rights.  
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal  
permission to copy, distribute and/or modify the library.  
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by  
someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s  
reputation will not be affected by problems that might be introduced by others.  
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot  
effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.  
Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use  
specified in this license.  
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser  
General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use  
this license for certain libraries in order to permit linking those libraries into non-free programs.  
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a  
combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire  
combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the  
library.  
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General  
Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These  
disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides  
advantages in certain special circumstances.  
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it  
becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library.  
A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by  
limiting the free library to free software only, so we use the Lesser General Public License.  
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of  
free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole  
GNU operating system, as well as its variant, the GNU/Linux operating system.  
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is  
linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.  
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a  
“work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter  
must be combined with the library in order to run.  
75  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Appendix  
GNU Lesser General Public License  
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION  
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or  
other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”).  
Each licensee is addressed as “you”.  
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs  
(which use some of those functions and data) to form executables.  
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on  
the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a  
portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation  
is included without limitation in the term “modification”.)  
“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code  
means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control  
compilation and installation of the library.  
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of  
running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a  
work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the  
Library does and what the program that uses the Library does.  
1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that  
you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact  
all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the  
Library.  
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange  
for a fee.  
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and  
distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions:  
a) The modified work must itself be a software library.  
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.  
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.  
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the  
facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in  
the event an application does not supply such function or table, the facility still operates, and performs whatever part of its  
purpose remains meaningful.  
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application.  
Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the  
application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified  
work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent  
and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as  
separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution  
of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to  
each and every part regardless of who wrote it.  
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to  
exercise the right to control the distribution of derivative or collective works based on the Library.  
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a  
volume of a storage or distribution medium does not bring the other work under the scope of this License.  
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To  
do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License,  
version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared,  
then you can specify that version instead if you wish.) Do not make any other change in these notices.  
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all  
subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the  
Library into a program that is not a library.  
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the  
terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code,  
which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.  
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy  
the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not  
compelled to copy the source along with the object code.  
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or  
linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore  
falls outside the scope of this License. However, linking a “work that uses the Library” with the Library creates an executable that is  
a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is  
therefore covered by this License. Section 6 states terms for distribution of such executables.  
76  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
14  
When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be  
a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be  
linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.  
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline  
functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative  
work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)  
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any  
executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.  
6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a  
work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit  
modification of the work for the customer’s own use and reverse engineering for debugging such modifications.  
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered  
by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include  
the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License.  
Also, you must do one of these things:  
a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes  
were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with  
the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the  
user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood  
that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application  
to use the modified definitions.)  
b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a  
copy of the library already present on the user’s computer system, rather than copying library functions into the executable,  
and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is  
interface-compatible with the version that the work was made with.  
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection  
6a, above, for a charge no more than the cost of performing this distribution.  
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above  
specified materials from the same place.  
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.  
For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for  
reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that  
is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating  
system on which the executable runs, unless that component itself accompanies the executable.  
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany  
the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you  
distribute.  
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library  
facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work  
based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things:  
a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library  
facilities. This must be distributed under the terms of the Sections above.  
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where  
to find the accompanying uncombined form of the same work.  
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any  
attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your  
rights under this License. However, parties who have received copies, or rights, from you under this License will not have their  
licenses terminated so long as such parties remain in full compliance.  
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or  
distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by  
modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and  
all its terms and conditions for copying, distributing or modifying the Library or works based on it.  
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the  
original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any  
further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by  
third parties with this License.  
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues),  
conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they  
do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations  
under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all.  
For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or  
indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of  
the Library.  
77  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Appendix  
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is  
intended to apply, and the section as a whole is intended to apply in other circumstances.  
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any  
such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented  
by public license practices. Many people have made generous contributions to the wide range of software distributed through that  
system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute  
software through any other system and a licensee cannot impose that choice.  
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.  
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the  
original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding  
those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates  
the limitation as if written in the body of this License.  
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time.  
Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.  
Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it  
and “any later version”, you have the option of following the terms and conditions either of that version or of any later version  
published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version  
ever published by the Free Software Foundation.  
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these,  
write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free  
Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free  
status of all derivatives of our free software and of promoting the sharing and reuse of software generally.  
NO WARRANTY  
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED  
BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES  
PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT  
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE  
RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU  
ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.  
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY  
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR  
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR  
INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE  
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),  
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
END OF TERMS AND CONDITIONS  
How to Apply These Terms to Your New Libraries  
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that  
everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms  
of the ordinary General Public License).  
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most  
effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice  
is found.  
<one line to give the library’s name and an idea of what it does.>  
Copyright (C) year name of author  
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as  
published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.  
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of  
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.  
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software  
Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA  
Also add information on how to contact you by electronic and paper mail.  
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library,  
if necessary. Here is a sample; alter the names:  
Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random  
Hacker.  
signature of Ty Coon, 1 April 1990  
Ty Coon, President of Vice  
That’s all there is to it!  
78  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
14  
Specifications  
Item  
50"Plasma Display, Model: PRO-505PU  
43" Plasma Display, Model: PRO-435PU  
Number of Pixels  
1280 × 768 pixels  
1024 × 768 pixels  
Audio Amplifier  
Surround System  
Power Requirement  
Dimensions  
13 W + 13 W (1 kHz, 10 %, 8 Ω)  
SRS/FOCUS/TruBass  
13 W + 13 W (1 kHz, 10 %, 8 Ω)  
SRS/FOCUS/TruBass  
120 V AC, 60 Hz, 363 W (0.2 W Standby)  
120 V AC, 60 Hz, 298 W (0.2 W Standby)  
1270 (W) × 737 (H) × 93 (D) mm  
1120 (W) × 652 (H) × 93 (D) mm  
11  
1
11  
11  
(50 (W) × 29 (H) × 3 /16 (D) inches)  
(44 /8 (W) × 25 /16 (H) × 3 /16 (D) inches)  
Weight  
32.8 kg (72.3 lbs.)  
26.8 kg (59.1 lbs.)  
Item  
Media Receiver, Model: PRO-R05U  
Reception System (Digital)  
ATSC Digital TV system  
Circuit type  
8VSB/64QAM/256QAM/QPSK demodulation  
VHF 2–13ch, UHF 14–69ch  
2–135ch  
Tuner  
VHF/UHF  
CATV  
Audio format  
Dolby Digital  
Reception System (Analog)  
American TV standard NTSC system  
Circuit type  
Video signal detection PLL full synchronous detection, PLL digital synthesizer  
system  
Tuner  
Rear  
VHF/UHF  
CATV  
VHF 2–13ch, UHF 14–69ch  
ANTENNA/CABLE A IN: 1–135ch  
BTSC system  
Cable: 1–125ch  
Audio multiplex  
Terminals  
ANTENNA/CABLE A IN 75 Ω UNBAL, F Type for DTV/VHF/UHF/CATV in  
ANTENNA B  
75 Ω UNBAL, F Type for VHF/UHF/CATV in  
Loop out  
i.LINK (TS)  
S400 (2)  
INPUT 1  
COMPONENT VIDEO in, S-VIDEO in, VIDEO in, AUDIO in, HDMI in  
INPUT 2  
S-VIDEO in, VIDEO in, AUDIO in  
INPUT 3  
COMPONENT VIDEO in, AUDIO in, HDMI in  
Monitor Out  
Digital Audio Output  
VCR Control Output  
CONTROL IN  
CONTROL OUT  
Cable CARD  
INPUT 4  
S-VIDEO out, VIDEO out, AUDIO out  
Optical (1)  
1
1
1
Point of Deployment  
Front  
COMPONENT VIDEO in, S-VIDEO in, VIDEO in, AUDIO in  
Analog RGB in, AUDIO in  
PC  
OSD  
English/French/Spanish  
Power Requirement  
120 V AC, 60 Hz, 43.3 W (31 W Standby)  
Dimensions  
420 (W) × 90 (H) × 295 (D) mm  
9
9
10  
(16 /16 (W) × 3 /16 (H) × 11 /16 (D) inches)  
Weight  
5.8 kg (12.8 lbs.)  
• Design and specifications are subject to change without notice.  
79  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Appendix  
Trademarks  
• FOCUS, WOW, SRS and  
symbol are trademarks of SRS Labs, Inc.  
FOCUS and WOW technologies are incorporated under license from SRS Labs, Inc.  
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.  
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.  
• This product includes FontAvenue® fonts licensed by NEC Corporation. FontAvenue is a registered trademark of NEC Corporation.  
• “i.LINK” and the “i.LINK” logo are trademarks.  
• DDC is a registered trademark of Video Electronics Standards Association.  
• CableCARD is a trademark of Cable Television Laboratories, Inc.  
• The names of the companies or institutions are trademarks or registered trademarks of the respective companies or institutions.  
Copyright protection  
• This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.  
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other  
limited consumer uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.  
Published by Pioneer Corporation.  
Copyright © 2004 Pioneer Corporation.  
All rights reserved.  
80  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed on recycled paper  
Imprimé sur papier recyclé  
Published by Pioneer Corporation.  
Copyright © 2004 Pioneer Corporation.  
All rights reserved.  
PIONEER CORPORATION  
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan  
PIONEER ELECTRONICS (USA) INC.  
P.O. BOX 1540, Long Beach, California 90810-1540, U.S.A. TEL: (800) 421-1404  
PIONEER ELECTRONICS OF CANADA, INC.  
300 Allstate Parkway, Markham, Ontario L3R OP2, Canada TEL: 1-877-283-5901  
PIONEER EUROPE NV  
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11  
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.  
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555  
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.  
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300  
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.  
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270  
<04H00001>  
Printed in Japan / Imprimé au Japon <ARB1566-A>  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peerless Industries Network Router HDS200 User Manual
Pelco Marine Instruments PSKIT8100 User Manual
Phantom Tech Door QC03 0903R User Manual
Philips CD Player AZ1816 User Manual
Philips Stereo Receiver TC8275 User Manual
Philips Telephone XL390 User Manual
Pinnacle Products International Air Cleaner BCB 36 BDF User Manual
Polk Audio Home Theater System 255C LS User Manual
Presto Kitchen Utensil electric slicer shredder User Manual
ProForm Treadmill 831295032 User Manual