Digital Projection Television
64PH9901
Instructions for use
A
T
S
C
C
E
R
T
I
F
I
E
D
TM
D I G I T A L T E L E V I S I O N
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS - Read before operating equipment
This product was designed and manufactured to meet strict quality and
safety standards. There are, however, some installation and operation
precautions which you should be particularly aware of.
11. Power-Cord Protection - Power supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords and
plugs, convenience receptacles, and the point where they exit from
the appliance.
1. Read Instructions - All the safety and operating instructions should
be read before the appliance is operated.
12. Cleaning - The appliance should be cleaned only as recommended
2. Retain Instructions - The safety and operating instructions should
by the manufacturer.
be retained for future reference.
13. Power Lines - An outdoor antenna should be located away from
3. Heed Warnings - All warnings on the appliance and in the operating
power lines.
instructions should be adhered to.
14. Outdoor Antenna Grounding - If an outside antenna is connected to
the receiver, be sure the antenna system is grounded so as to
provide some protection against voltage surges and built up static
charges.
4. Follow Instructions - All operating and use instructions should be
followed.
5. Water and Moisture - The appliance should not be used near water
- for example, near a bathtub, washbowl, kitchen sink, laundry tub,
in a wet basement or near a swimming pool, etc.
Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984,
provides information with respect to proper grounding of the mats
and supporting structure grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of
antenna-discharge unit, connection to grounding electrodes and
requirements for the grounding electrode. See Fig. below.
6. Carts and Stands - The appliance should be used only with a cart or
stand that is recommended by the manufacturer.
6A.
An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart combination
to overturn.
15. Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of
time.
16. Object and Liquid Entry - Care should be taken so that objects do
not fall and liquids are not spilled into the enclosure through
openings.
6B. Tilt/Stability - All televisions must comply with recommended
international global safety standards for tilt and stability properties
of its cabinet design.
•
Do not compromise these design standards by applying exces-
sive pull force to the front, or top, of the cabinet which could
ultimately overturn the product.
Also, do not endanger yourself, or children, by placing elec-
tronic equipment/toys on the top of the cabinet. Such items
could unsuspectingly fall from the top of the set and cause
product damage and/or personal injury.
17. Damage Requiring Service - The appliance should be serviced by
qualified service personnel when:
•
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the
appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits
a marked change in performance; or
7. Wall or Ceiling Mounting - The appliance should be mounted to a
wall or ceiling only as recommended by the manufacturer.
E. The appliance has been dropped, or the enclosure damaged.
8. Ventilation - The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example,
the appliance should not be situated on a bed, sofa, rug, or similar
surface that may block the ventilation openings; or, placed in a
built-in installation, such as a bookcase or cabinet that may impede
the flow of air through the ventilation openings.
18. Servicing - The user should not attempt to service the appliance
beyond that described in the operating instructions. All other
servicing should be referred to qualified service personnel.
9. Heat - The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
10. Power Sources - The appliance should be connected to a power
supply only of the type described in the operating instructions or as
marked on the appliance.
Note to the CATV system installer: This reminder is provided to call the
CATV system installer's attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Example of Antenna Grounding
as per NEC - National Electric Code
GROUND CLAMP
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
ELECTRIC SERVICE EQUIPMENT
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
12
S
S
F
o
p
e
u
e
a
r
s
s
1
5
Getting Started
11
7
t
r
e
DTV
S
e
t
u
p
ATSC Digital On-Screen Menu Features
2
10
E
xit
9
3
8
4
6
Welcome/Product Registration ...................2
DTV SETUP
Safety/Precautions .....................................................3
Table of Contents.......................................................4
Features, Model and Cabinet Information .................5
✧Automatic Programming of area Digital
(over-the-air) Broadcast Channels ...................29
PICTURE MENU
✧Adjusting Color, Brightness, Sharpness,
M
AIN
M
ENU
P
I
CTURE
S
OUN
D
Tint, and Picture Controls.................................30
FEATURES
1
S
T
TIM
E
S
ETUP
EXI
T
NTSC Analog On-Screen Menu Features
✧Adjusting DTV Convergence............................31
FIRST TIME SETUP
SOUND MENU
✧Automatic Programming of local NTSC
Channels and other Control Features .................6
✧Surround Sound Speaker Connections..............32
✧Selecting the DPTV Surround Mode Control...33
PICTURE MENU
✧Dolby Digital Internal and External Speaker
System Use and Connections ......................33-34
✧Adjusting Color, Brightness, Sharpness,
Tint, and Picture Controls...................................7
✧Adjusting Bass and Treble Sound Controls......35
✧Using the Clearview Control...............................8
✧Using the Auto Volume Control .......................35
✧Adjusting the DPTV's Convergence Control ......9
SPEAKERS MENU
FEATURES MENU
✧Adjusting Speaker Menu Controls for
Front/Center/Rear multi-speaker arrangements36
✧Setting the Smart Picture Controls ..............10-11
✧Setting the DPTV for Closed Captioning..........12
✧Setting the DPTV for Cable/Antenna Signals...13
✧Adding Channels in Memory (Automatically) .14
✧Adding Channels in Memory (Manually).........15
✧Setting the DPTV Clock....................................16
✧Adjusting the Channel Display Control............17
✧Using the Channel Label Control .....................18
✧Using the Test Tone Audio Signal Control.......37
FEATURES MENU
✧Using the DPTV for ATSC Closed Captioning 38
✧Adding Channels in Memory (Manually).........39
Pronto Remote ATSC Features
✧Digital ATSC DPTV Features ..........................40
SOUND MENU
✧Adjusting Bass, Treble, and Balance Sound
Controls.............................................................19
BRIGHTNES
S
P
S
S
I
CTURE
HARP
VM
N
ES
S
OFF
COLOR
TI
VOLUM
N
T
E
B
A
R
O
N
MONITOR On-Screen Features
✧Connection of VGA/SVGA/ and High Definition
(HD) Component Video auxiliary equipment .41
✧Setting the DPTV for Stereo/SAP Programs ...20
✧Using the Volume Display Control...................21
✧Using the Automatic Volume Limiter Control .22
✧Adjusting of DPTV Monitor Display controls
(for VGA/SVGA/EXT HD devices) ................42
Pronto Remote NTSC Features
General Information
✧Analog NTSC DPTV Features..........................23
Tips if Something Isn’t Working ...............43
Audio/Video NTSC Connections
✧Auxiliary 1/2/3 Audio/Video Inputs............24-25
✧S-Video Input....................................................26
✧Audio/Video Outputs........................................27
✧System Audio Output Connections ..................28
Cleaning and Care....................................................43
Index ........................................................................44
Regulatory Notices ..................................................44
Glossary of DPTV Terms ........................................45
Factory Service Locations ..................................46-47
Warranty ..................................................................48
Copyright © 1998 Philips Consumer Electronics. All rights reserved.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
ATSC Certified - for full compliance with analog
NTSC and all 18 digital ATSC formats as specified by
the Federal Communications Commission (FCC).
DPTV SET-UP AND QUICK USE GUIDE
Use the Set-Up Guide (supplied with your
DPTV information packet) for details on:
High Definition Digital - with full 1920 x 1080
interlaced image resolution capability to achieve
superior image performance.
• Antenna Hook-ups
DIGITAL PROJECTION TELEVISION
QUICK USE GUIDE
TM
A
G
T
I
S
C
C
E
R
T
I
F
V
I
E
D
TABLE OF CONTENTS
Getting Started
-
D
I
T
A
L
T
E
L
E
I
S
I
O
N
•
For details on product safety, registration,
warranty, and service refer to the other literature
included with your TV information packet.
Warning/Precautions
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.1
.1
DPTV Integrated Product Design and Features
Please retain all these materials and keep them
handy for future reference.
Basic DPTV and Remote Control Description of
Controls and Operations
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.2-3
NOTE: Not all features (and drawings) discussed in this
owner’s manual will necessarily match those found with
your television set. This is normal and does not require you
contacting your dealer or requesting service.
• First Time Use and
Control Descriptions
S
C
V
L
M
V
L
E
I
Digital (ATSC) Menu Control Operations
Analog (NTSC) Menu Control Operations
.
.
.
.
.
.
.4-5
D
W
N
.
.
.
.
.
.
.
.
.
.6
.7
Monitor Menu Control Operations
Digital TV Rollout
.
.
.
.
.
.
.
.
.
.
.
.
WARNING: TO PREVENT FIRE OR SHOCK
-
Time/Terms/& Technology .8
HAZARD DO NOT EXPOSE THIS UNIT TO
RAIN OR EXCESSIVE MOISTURE.
64PP9901 Digital Projection Television
TS1001 Pronto Remote Control
64" Widescreen Display - with a super-large 64"
Widescreen 16:9 display format which provides for a
true home theater or cinematic experience. If a 4:3
aspect ratio picture is the primary source, it will be
expanded to fill the screen.
INTEGRATED
PRODUCT DESIGN
DPTV/NTSC/MONITOR
he Philips
T64PP9901 Digital
Projection Television
(DPTV) represents an
advanced first step con-
cept in integrated digital
products. Designed for
discrete and cross-over
system functionality the
64PP9901 will support
traditional NTSC
digital 1nf0rmation
refer to the rear
Please
section of this Quick-
Use guide (page 8) for
additional information on:
¥scheduled Digital
¥the basics on how HDTV,
Digital, and Analog TV
systems differ and how
they can be received
¥other ATSC (or Advanced
Television System
• Basic DPTV and
Pronto Remote
Operation
Broadcast program roll-
out dates, and what will
be available from the
various networks and
program suppliers
Committee) news and
details on digital broad
casting product opera-
tions and services
Television standards,
receive all certified FCC
defined ATSC digital
transmission formats, as
well as perform PC
i
i
120-Watt Amplifier - to provide up to 20 watts
amplification for each of the Left/Right front, Center,
Left/Right rear Surround, and Subwoofer channel
speakers.
• DTV Program Rollout Information
First Time Set Up - for both NTSC and ATSC
channel programming to automatically preset the
DPTV for available area stations.
As you unpack your DPTV please note that the
TV Guide Plus+™ Programming - which downloads
NTSC channel program information including on-
screen program summaries and sorts by viewing
preference categories (sports, movies, etc.). Microchip
storage capacity and channel availability determine
volume of downloaded data.
following items have been included with your set:
•
Owner's Manual and DPTV Quick Use Guide
-
-
Safety Tip Information
Factory Service Center Locations
•
•
Warranty Registration Card
Pronto Remote Control Transmitter
Pronto Remote Control - universal, learn remote
which controls virtually all IR devices, learns new
commands as your system expands, and can be
customized according to your personal preferences.
Featuring a large LCD backlit touchscreen, the Pronto
gives you easy access to all key DPTV features.
Dolby® Digital Sound - for multichannel sound
reproduction at its best. Fully compatible DPTV audio
system will replay a received Dolby Digital 5.1 sound
source through internal system amplification, or
function within a home theater sound system.
-
Product Package contains dedicated Pronto
Owner’s Manual information
•
•
Batteries for Remote Control Use
Guide Plus+ program Setup and Use
information
Please take a few minutes to complete your
registration card. The serial number for the DPTV
is on the back of the product.
Refer to the back of this manual for instructions on
the cleaning and care of the DPTV.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished
Works. ©1992-1997 Dolby Laboratories, Inc.
All rights reserved.
Audio/Video Connections - for external sources and
home theater equipment to provide the ultimate in
flexibility. In addition to separate NTSC/ATSC antenna
inputs, connections include inputs formatted for S-
Video; composite video; Left/Right audio; six-channel
audio (directly to internal amplifiers); External Center
Channel Audio Amplifier Inputs; VGA; and High
Definition component video.
Product End-of-Use disposal
Your new digital projection television and its
packaging contain materials that can be recycled
and reused. Specialized companies can recycle
your product to increase the amount of reusable
materials and minimize the amounts which need
to be properly disposed.
Output possibilities include Left/Right audio; SPDIF;
rear speaker connections; front speaker connections;
variable and amplified subwoofer speaker connections.
Your product also uses batteries which should not
be thrown away when depleted, but should be
handed in and disposed of as small chemical
waste.
VGA/SVGA - 15-pin D-sub female connection for
impressive multimedia display of computer source
material through the DPTV’s Monitor operation mode.
Please find out about the local regulations on how
to dispose of your old products, batteries, and
packaging materials whenever you replace
existing equipment.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG ON-SCREEN MENU FEATURES
FIRST TIME SETUP
Press the Pronto remote’s
“analog TV” (or the “Source”
button on the DPTV’s local
keyboard) to select the NTSC
operating mode.
irst Time Setup automatically takes
Fcare of some basic control feature
settings for you. Follow the steps in this
section to quickly add area channel
numbers into the DPTV's scan system
memory, and set the DPTV for your
connected signal (Antenna or Cable.)
You can also set-up your TV Guide
Plus+ feature for the first time as well.
NTSC
ANALOG MAIN MENU
3
1
PICTURE SOND
TV
2
FEATURES
menu
1 ST TIME SETUP
EXIT
M
exit
UP
CH
VOL
–
M
+
SOURCE
EXIT
VOL
CH
DOWN
Analog
4/4
DTV
2
BEGIN
1
2
Press the MENU (M) button on
the Pronto remote or DPTV. An on-
screen list of NTSC features shows
on the "MAIN MENU".
The Firs t-Time Setup
Select "1ST TIME SETUP" on
the DPTV's Main Menu. (Selected
MENU item is highlighted in RED.)
provides a s imple method
of adjus ting the mos t
important controls for
this televis ion receiver.
Many of the current TV
control s ettings will be
modified by continuing
with Firs t-Time Setup.
This TV is equipped with
the TV Guide Plus+ feature.
Press the remote's Menu
This feature is designed
to operate only on the
analog TV antenna.
buttons to move UP/DOWN and
from SIDE-TO-SIDE within the list
of on-screen features.
Press "M" To Continue
Press STATUS to Quit
or
Press "M" to Continue
Press "M" to Continue
Press CH(annel)▲ ▼ and
VOLume (+) (-) on the DPTV’s
local keyboard to move UP/DOWN
and from SIDE-TO-SIDE within
the list of on-screen features.
OR
Pleas e check that your
analog TV antenna or cable is
connected to the plug
marked ANT on
*
Pleas e W ait *
*
Please W ait *
the TV rear input panel.
Sys tem is tes ting for
correct tuning mode
for the analog TV antenna.
Sys tem is s earching for
all active channels
for the analog TV antenna.
Press STATUS to Quit
or
Press "M" to Continue
3
Press MENU (M) button on the
remote or DPTV to begin SETUP.
1
Tes ting channel 2
in cable mode.
Follow the instructions shown on
the screen to guide you through the
First Time Setup and use of your
new DPTV.
The s earch for active
channels is complete
STOP
for the analog TV antenna.
1 7 channels were found
and s aved in memory
.
PRESS
TO ALIGN RED
Press "M" to Continue
SMART HELP
PRESS
TO ALIGN BLUE
PRESS MENU TO RETURN
PRESS MENU TO RETURN
Remember, SETUP is a
first-use, one-time operation
and will not have to be repeated.
SP
PLEASETRV GEUIDFE PELURS
+
Press the “exit” button on the
remote or DPTV to stop the
SETUP at any time.
Setup
- Note -
TO YOUR
After ALL connections
and First-Time Setup
for TV GUIDE PLUS +
are completed, the TV
will have to be turned
OFF overnight to receive
program information.
TV GUIDE PLUS +
This completes the
First-Time Setup.
W here do you live?
USER MANUAL
B
USA
FOR DETAILS ON
Note: Because of the variety of
connections possible with the
Guide Plus+ feature, refer to the
separate Guide Plus+ manual for
complete details on its setup and
use.
Y CANADA
1st TIME SETUP.
Press color key to select
Press "M" to Exit Setup
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG PICTURE MENU CONTROLS
COLOR, BRIGHTNESS,
SHARPNESS, TINT, PICTURE
o adjust your DPTV color and
Tpicture controls, select a TV
channel and follow the steps shown
NTSC
below:
BEGIN
ANALOG MAIN MENU
PICTURE
1
Select BRIGHTNESS,
PICTURE, COLOR, TINT, or
SHARPNESS picture control.
SOUND
FEATURES
PICTURE MENU
COLOR
EXIT
1 ST TIME SETUP
TINT
With the PICTURE MENU on-
screen, move the RED highlight
BRIGHT
SHARP
EXIT
PICTURE
with the MENU (M)
buttons.
CLEARVIEW
MORE...
Then press the MENU button.
1
OF 2
Press the ᮤ or ᮣ arrow
buttons to adjust the selected
control.
2
3
Press the “exit” button to clear
mute
1
the screen.
channel
TV
+
STOP
menu
volume
COLOR
+
M
MIN
MAX
SMART HELP
exit
EXIT
NEXT...
Analog
4/4
DTV
Remember, control
settings are at normal mid-
range levels when the bar scale is
centered.
1
2
Select and then press MENU
(M) button to view additional
controls grouped under same
feature heading. For
Example: Tint, Brightness,
Picture, etc.
3
COLOR Press (-) or (+) to add or
eliminate color.
BRIGHTNESS Press (-) or (+) until
dark parts of the picture show good
detail.
SHARPNESS Press (-) or (+) to
improve detail in the picture.
TINT Press (-) or (+) to obtain
natural skin tones.
HOW TO SELECT MENU FEATURES
WITH BUTTONS ON THE PRONTO REMOTE (PAGE 4/4 ANALOG TV MODE)
PICTURE Press (-) or (+) until
whitest parts of the picture are as
bright as you prefer.
menu
Press Left/Right ᮤ ᮣ
Arrow buttons to move
from Side-to-Side within
M
the Menu.
Press MENU or (M)
to select RED
highlighted feature.
exit
Press Up/Down Arrow
buttons ▲ ▼ to move
Up and Down within
the Menu.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG PICTURE MENU CONTROLS
CLEARVIEW
learview is a sharpness feature
Cwhich smoothes out
background snow (or picture noise)
without losing picture image detail
or crispness.
NTSC
BEGIN
ANALOG MAIN MENU
PICTURE
SOUND
1
Select CLEARVIEW control.
FEATURES
PICTURE MENU
COLOR
With the PICTURE MENU on-
screen, move the RED highlight
1 ST TIME SETUP
EXIT
TINT
with the MENU (M)
Then press the MENU button.
buttons.
BRIGHT
SHARP
EXIT
PICTURE
CLEARVIEW
MORE...
1
OF 2
Press the MENU ▲▼ buttons
to move the RED highlight. Press
the MENU button to select (
ߜ ) the ENHANCED mode.
2
2
1
mute
Press the “exit” button to clear
the screen.
3
annel
TV
2
CLEARVIEW
NORMAL
ENHANCED
menu
volume
STOP
+
M
exit
EXIT
NEXT...
Analog
4/
DTV
1
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG PICTURE MENU CONTROLS
RED/BLUE CONVERGENCE
onvergence is the correct
Clining up of the red and blue
light paths on the DPTV screen.
NOTE: If no color fringing (see
Smart Help) shows, then no
Convergence adjustments are
necessary.
NTSC
ANALOG MAIN MENU
PICTURE
BEGIN
SOUND
Select CONVERGENCE
control.
1
PICTURE MENU
COLOR
FEATURES
TINT
1 ST TIME SETUP
EXIT
BRIGHT
SHARP
EXIT
PICTURE
With PICTURE MENU (2 of 2)
on-screen, move the RED highlight
CLEARVIEW
MORE...
with the MENU (M)
buttons.
Then press the MENU button.
1
OF 2
2
3
Press the MENU ▲▼ buttons
to select either the Red or Blue
Convergence control, press the
MENU button to continue.
PICTURE MENU
CONVERGENCE
2
mute
1
channel
Press the MENU
buttons
TV
+
2
1
to move the selected red (or blue)
convergence cross directly over the
white cross on the DPTV screen.
menu
volume
+
M
MORE...
OF 2
EXIT
3
2
The red (or blue) cross is properly
adjusted when it is completely
merged with the white cross. (No
color appears around the edge of
the white cross).
exit
Analog
/4
DTV
4
PICTURE MENU
RED
CONVERGENCE
Press the “exit” button to clear
the screen when convergence
adjustments are complete.
4
BLUE
CONVERGENCE
STOP
EXIT
SMART HELP
Remember, Convergence
has been set at the factory for
best viewing, but if one or more of
the (red or blue) colors appear
around the edges of objects (color
fringing) follow the steps given in
this section.
PRESS
TO ALIGN RED
PRESS MENU TO RETURN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NTSC ANALOG FEATURE MENU CONTROLS
SMART PICTURE
ith Smart Picture you can set a
Wnumber of video and audio
controls to your own personal
preference. Once the individual
controls have been adjusted to the
levels you desire, use the list of Smart
Picture feature category titles to
quickly reselect these “personalized”
settings contained within the memory
of the DPTV. (See the next page for
more details on the labeling options
and use of Smart Picture.)
NTSC
ANALOG MAIN MENU
PICTURE
SOUND
FEATURES
FEATURE MENU
SMART
1 ST TIME SETUP
EXIT
CABLE
TUNING
PICTURE
BEGIN
CLOSED
CAPTION
CHANNEL
MEMORY
1
2
Select the SMART PICTURE
control.
MORE...
OF 2
EXIT
1
With the FEATURES MENU on-
screen, move the RED highlight
3
2
with the MENU (M)
buttons.
SMART PICTURE
Then press the MENU button.
mute
1
LABEL 1
LABEL 2
LABEL 3
LABEL 4
LABEL 5
annel
TV
2
Press the MENU ▲▼ buttons to
highlight the category list for Smart
Picture. Press the MENU button to
select (
ߜ ) the desired title. menu
volume
+
FACTORY SETTINGS
M
M
to SELECT
exit
EXIT
Analog
4/
DTV
3
1
Press the MENU(M)
buttons
3
4
to choose any of the individual
controls you wish to adjust for the
Smart Picture selected title. Then
press the Menu (M) button to select
the highlighted control.
5
SMART PICTURE MENU
CHANGE LABEL
COLOR
TINT
SHARP
4
5
Press the Menu ᮤ or ᮣ arrow
BRIGHT
PICTURE
(or Menu (M)
) buttons to
adjust the selected control.
MORE...
OF 2
EXIT
1
Press the “exit” button on the
remote to clear the screen after you
have finished with all of your Smart
Picture feature control adjustments.
SMART PICTURE MENU
CLEARVIEW
SAP
TREBLE
STEREO
STOP
BASS
BALANCE
SMART HELP
MORE...
OF 2
EXIT
Note: Select the
2
“FACTORY SETTINGS”
category to automatically return the
DPTV to the video and audio control
levels preset at the factory prior to
product shipment.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
SMART PICTURE
ollowing your initial setup
Fadjustments (see previous page),
just select the desired Smart Picture
category in order to place the DPTV
to the personalized set of audio and
video control settings for that title.
FEATURE MENU
SMART
CABLE
TUNING
PICTURE
BEGIN
CLOSED
CAPTION
CHANNEL
MEMORY
1
Select the SMART PICTURE
SMART PICTURE
control.
MORE...
OF 2
EXIT
LABEL 1
LABEL 2
LABEL 3
LABEL 4
LABEL 5
1
With the FEATURES MENU on-
screen, move the RED highlight with
the MENU (M)
FACTORY SETTINGS
buttons. Then
M
to SELECT
press the MENU button.
EXIT
Press the MENU (M) ▲▼
buttons with the list of “SMART
PICTURE” categories on the DPTV
screen to highlight the desired
category. Then press the Menu (M)
button to select the audio and video
control settings for that particular
title.
2
2
1
mute
annel
TV
2
menu
volume
+
M
exit
3
Press the “exit” button on the
remote to clear the screen.
Analog
4/
DTV
1
STOP
3
CHANGE LABEL
SMART PICTURE MENU
he "CHANGE LABEL" control
Tcan be used to update the title of
a SMART PICTURE setting into a
name or label that may be easier for
you to remember.
COLOR
TINT
CHANGE LABEL
SHARP
BRIGHT
EXIT
PICTURE
SMART PICTURE LABEL
MORE...
OF 2
1
M Y O W
N
BEGIN
With the "SMART PICTURE
LABEL" control on-screen, press
the MENU ▲▼ buttons to spell out
a new label or title for the selected
SMART PICTURE category title.
1
or
or
to SELECT
to CHANGE
M
when FINISHED
2
3
Press the MENU ᮤ ᮣ buttons
to move the red highlight to each
letter space.
mute
annel
TV
1
menu
volume
+
Press the “exit” button to clear
M
the screen when the new label is
exit
finished.
4/
Analog
DTV
2
STOP
3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
CLOSED CAPTION
NOTE: Not all TV programs and product commercials are made for
broadcast with Closed Caption (CC) information included. Neither are all
Closed Caption modes (CAPTION 1-4; or TEXT 1-4) necessarily being used by a
broadcast station during the transmission of a closed caption program. Usually
"CAPTION 1" is the most used mode to view captioned material. Refer to your
area's TV program listings for the stations and times of Closed Caption shows.
losed Captioning (CC) allows
Cyou to read the voice content of
NTSC television programs on the
DPTV screen. Designed to help the
hearing impaired this feature uses
on-screen "text boxes" to show
dialogue and conversations while
the TV program is in progress.
CC
BEGIN
Select CLOSED CAPTIONING
control.
1
2
NTSC
FEATURE MENU
ANALOG MAIN MENU
With the FEATURES MENU on-
screen, move the RED highlight
SMART
CABLE
PICTURE
TUNING
PICTURE
SOUND
with the MENU (M)
buttons.
CLOSED
CAPTION
CHANNEL
MEMORY
FEATURES
Then press the MENU button.
1 ST TIME SETUP
EXIT
MORE...
OF 2
EXIT
Press the MENU ▲▼ buttons
to move the RED highlight. Press
the MENU button to select (
ߜ ) the desired Closed Caption mode - For
Example: "ALWAYS ON" and
"CAPTION 1".
1
NOTE: The ON DURING
MUTE ONLY control can
be used to set the DPTV to
turn the Closed Caption
mode "ON" whenever the
MUTE button on the
CLOSED CAPTION
ALW AYS ON
ALW AYS OFF
ON DURING MUTE ONLY
CAPTION 1, 2, 3, 4:
remote is pressed.
dialogue (and descriptions)
for the action on the captioned
TV program shows on-screen.
(See Important Note on this
page.)
CAPTION 1
CAPTION 2
CAPTION 3
CAPTION 4
TEXT 1
TEXT 2
TEXT 3
TEXT 4
2
1
mute
2
nnel
T
+
EXIT
menu
volume
+
TEXT 1, 2, 3, 4:
M
often used for channel guide,
schedules, or bulletin board
information for CC programs.
exit
Analog
4/4
DTV
1
After making your Caption mode
selection, press the “exit” button to
clear the screen. The selected
3
3
Closed Caption mode will be active.
JOHN: Why did they move the
meeting up to this week?
MARSHA: I don't know, but they
are pushing to close the deal.
To cancel, set the Closed Captioned
feature to OFF when finished.
CAPTION 1 mode
Example Screen Display
STOP
CLOSE CAPTION PROGRAMS ON WXYZ
SMART HELP
ALL ITEMS ARE EASTERN STANDARD TIME (EST)
CHECK LOCAL LISTINGS
FOR TIMES IN YOUR AREA
Remember, broadcast
stations will often use
6:00 TOP OF THE MORNING
10:00 THE BEST LITTLE CALL-IN SHOW EVER
12:00 NOONDAY NEWS
Closed Caption information will usually appear
in black and white (although some broadcasters
or networks may occasionally use color to
highlight or draw attention to certain areas.)
spelling abbreviations, symbols,
dropouts and other grammatical
shortcuts in order to keep pace
with the on-screen action. These
type factors vary upon the source
of the captioned text material and
do not indicate a need for service
on the part of the DPTV.
1:30 AS YOUR LIFE TURNS MY WORLD AROUND
6:00 WORLD NEWS FOR TODAY
9:00 PLAYHOUSE MOVIE OF THE WEEK
FULL SCREEN TEXT
will block DPTV screen from viewing
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
EATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
CABLE TUNING
ou need to make sure the
YDPTV is set to pick up either
Cable TV or Antenna signals. In
other words, the DPTV needs to
know if you connected a Cable TV
signal or a normal antenna to its
ANTENNA plug.
NTSC
ANALOG MAIN MENU
PICTURE
NOTE: If you went through First
Time Setup (see page 6), this task
has already been completed for
SOUND
FEATURES
you.
1 ST TIME SETUP
EXIT
FEATURE MENU
SMART
BEGIN
CABLE
TUNING
1
Select CABLE CHANNEL
PICTURE
TUNING control.
CLOSED
CAPTIONS
CHANNEL
MEMORY
With the FEATURES MENU on-
screen, move the RED highlight
MORE...
OF 2
EXIT
1
with the MENU (M)
buttons.
Then press the MENU button.
2
1
mute
Press the MENU ▲▼ buttons
to move the RED highlight. Press
the MENU button to select (
ߜ ) the desired mode - For Example:
CABLE.
2
annel
TV
2
CABLE TUNING
menu
volume
CABLE
+
M
NORMAL
exit
CABLE-
If you DO have
Cable TV connected
to the DPTV.
Channels 1-125
available.
EXIT
Analog
4/
DTV
1
3
NORMAL- If you have an
Antenna connected
to the DPTV.
Channels 2-69
available.
3
Press the “exit” button to clear
the screen.
STOP
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
CHANNEL MEMORY
AUTO-PROGRAMMING
our DPTV can automatically set
Yitself for local area (or Cable TV)
channels. This makes it easy for you
to select only the TV stations in your
area when the CHANNEL ▲▼
buttons are pressed.
NTSC
ANALOG MAIN MENU
PICTURE
SOUND
NOTE: If you went through First
Time Setup (see page 6), this task has
already been completed for you.
FEATURES
FEATURE MENU
SMART
CABLE
1 ST TIME SETUP
EXIT
PICTURE
TUNING
BEGIN
CLOSED
CAPTIONS
CHANNEL
MEMORY
Select CHANNEL MEMORY
(START AUTO-PROGRAMMING)
control.
1
2
MORE...
OF 2
EXIT
1
With the FEATURES MENU on-
screen, move the RED highlight with
the MENU (M)
buttons. Then
press the MENU button.
2
1
CHANNEL MEMORY
mute
ADD/ DELETE
CHANNELS
annel
Press the MENU ▲▼ buttons to
select the START AUTO-
TV
2
menu
START
volume
PROGRAMMING option, then press
the Menu button to begin.
+
AUTO-PROGRAMMING
M
EXIT
exit
The TV shows which channel
numbers are "SAVED" (
ߜ ) as they are added into memory.
Analog
4/
DTV
1
3
"Auto-programming CHANNEL
MEMORY is finished" shows when
the DPTV is through adding channels.
AUTO-PROGRAMMING
CHANNEL MEMORY
1
5
9
2
3
4
6
7
8
1 O
1 1
1 2
3
Press the “exit” (or Menu)
button to clear the screen.
1 3
1 7
2 1
1 4
1 8
2 2
1 5
1 9
2 3
1 6
2 0
2 4
ߜ Channel Numbers are Saved in Memory
STOP
Pres s "M" to
Stop Auto-Program
SMART HELP
Try it out. Press the
CHANNEL▲▼ buttons
and see which channels you can
select.
Remember, an Antenna or Cable
signal must first be connected to
your DPTV so that channels can
be saved.
If you want to delete any
unwanted channels from the
DPTV's memory, see
"ADD/DELETE CHANNELS" on
the next page.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
ADD/DELETE CHANNELS
uto-Programming (see
Aprevious page) adds all the
channels it can find (on your
Antenna or Cable TV system) into
the DPTV's memory. Add/Delete
Channels makes it easy for you to
add other channels, or drop
unwanted channels, from the list of
channels in the DPTV's memory.
BEGIN
NTSC
ANALOG MAIN MENU
PICTURE
SOUND
FEATURES
FEATURE MENU
SMART
1
Select CHANNEL MEMORY
(ADD/DELETE CHANNELS)
control.
CABLE
TUNING
1 ST TIME SETUP
EXIT
PICTURE
CLOSED
CAPTIONS
CHANNEL
MEMORY
With the FEATURES MENU on-
screen, move the RED highlight
MORE...
OF 2
EXIT
1
with the MENU (M)
buttons.
Then press the MENU button.
2
Press the CHANNEL (+)/(-)
(or number buttons on the Pronto’s
2/4 touchscreen display) to select
the channel you want to add or
delete.
CHANNEL MEMORY
mute
2
1
ADD/ DELETE
CHANNELS
channel
TV
+
menu
START
volume
+
AUTO-PROGRAMMING
3
Press the MENU ᮣ button to
ADD the channel into the DPTV's
memory.
M
EXIT
exit
Analog
4/
DTV
1
3
Press the MENU ᮤ button to
DELETE the channel from
memory.
4
Repeat steps 2 and 3 for each
channel you wish to add or delete.
ADD/ DELETE CHANNEL
Channel 1 9 Added
4
Press the “exit” (or Menu)
button to clear the screen when
through.
SELECT CHANNEL
to DELETE CHANNEL
when FINISHED
M
STOP
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
SET CLOCK
our DPTV comes with an on-
Yscreen clock. During normal
operation the clock appears on the
screen with every channel change
(and when the STATUS button is
pressed).
NTSC
FEATURE MENU
SMART
ANALOG MAIN MENU
PICTURE
BEGIN
CABLE
TUNING
PICTURE
SOUND
1
Select SET CLOCK control.
CLOSED
CAPTIONS
CHANNEL
MEMORY
FEATURES
With FEATURES MENU (2 of 2)
on screen, move the RED highlight
1 ST TIME SETUP
EXIT
MORE...
OF 2
EXIT
1
with the MENU (M)
buttons.
Then press the MENU button.
2
Press the remote's number
buttons (on the Pronto’s 2/4
touchscreen display) to set the time
clock.
FEATURE MENU
SET
CLOCK
CHANNEL
LABELS
CHANNEL
DISPLAY
mute
3
Press the “exit” button to set
the clock in operation and clear the
screen.
1
3
channel
+
TV
MORE...
OF 2
EXIT
1
menu
2
volume
+
STOP
M
exit
TV
2
Analog
4/4
DTV
SMART HELP
SET CLOCK
: 1 9 AM
Remember, be sure to
press "0" first and then the
hour number for single digit
entries.
9
A/CH
Analog
2/4
DTV
PLEASE ENTER THE
CURRENT HOUR
The remote's MENU (M)
buttons can also be used to set the
hours, minutes and AM/PM
portions of the clock.
DPTV Clock settings may be lost
when the unit is unplugged (or AC
power to the set is interrupted.)
SET CLOCK
9
: 1 9 AM
PLEASE USE or
TO SET AM/ PM
16
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
CHANNEL DISPLAY
ith the Channel Display
Wcontrol you can change the
size and location of the on-screen
channel and clock information.
BEGIN
NTSC
1
FEATURE MENU
SMART
Select CHANNEL DISPLAY
control.
ANALOG MAIN MENU
PICTURE
CABLE
TUNING
PICTURE
SOUND
With FEATURES MENU (2 of 2)
on-screen, move the RED
highlight with the MENU (M)
buttons. Then press the MENU
button.
CLOSED
CAPTION
CHANNEL
MEMORY
FEATURES
EXIT
1 ST TIME SETUP
MORE...
OF 2
EXIT
1
2
Press the MENU ▲▼ and
MENU (M) buttons to highlight
and select (
ߜ ) the LARGE or SMALL display control.
FEATURE MENU
SET
CLOCK
CHANNEL
LABELS
3
Press the “exit” button to clear
the screen.
CHANNEL
DISPLAY
2
1
mute
annel
TV
MORE...
OF 2
EXIT
2
STOP
2
menu
volume
+
M
exit
SMART HELP
Analog
4/
DTV
1
Try it out. Press the
CHANNEL ▲▼ buttons
and you should see the Display
Size you selected.
CHANNEL DISPLAY
LARGE
3
SMALL - CHANNEL/ LABEL
Remember, the SMALL SIZE
display shows only the channel
number, not the time (or clock).
EXIT
2
PBS
2
PBS
1 0 :0 6
CHANNEL DISPLAY OPTIONS
17
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG FEATURE MENU CONTROLS
CHANNEL LABELS
o you ever have trouble
Dremembering on which
channel a particular station or
network is located? The Channel
Labels Control is a quick way to
view and select channels from a
list of Labeled channels.
NTSC
FEATURE MENU
SET
CLOCK
CHANNEL
LABELS
CHANNEL
DISPLAY
A Label is a four letter callout you
can set to appear with the on-
screen channel number. Example
Label: WXYZ - for a TV station's
call letters.
MORE...
OF 2
EXIT
2
CHANNEL LABELS
Create Your Own
MANUAL
To create station labels using the
Channel Labels Control:
Choos e From Lis t
PRESETS
EXIT
2
1
BEGIN
mute
annel
Select CHANNEL LABELS
control.
1
TV
2
menu
volume
+
With the FEATURE MENU (2 of
2) on-screen, move the RED
highlight using the MENU (M)
buttons. Then press the MENU
(M) button.
M
exit
Analog
4/
DTV
1
3
BRV
CBN
2
Press the MENU ▲▼ and
MENU (M) buttons to highlight
and select either:
CHANNEL GUIDE LABEL
Channel
1
0
CBS
C H
1
0
C
B S
CNBC
CMT
"MANUAL" to create your own
label for a channel.
or
or
to SELECT
CHOOSE CHANNEL
to SELECT LABEL
to CHANGE
"PRESETS" to choose from a list
of prewritten channel labels.
when FINISHED
M
to EXIT
M
MANUAL- To create your
own Channel Label:
PRESETS -To pick a Label
from the "LABEL" list:
(See instruction details on this
page.)
Press the Channel ▲▼ or
Number buttons to select
desired station.
Press the Channel ▲▼ or
Number buttons to select
desired station.
3
Press the “exit” button to
clear the screen.
STOP
A red highlight shows the
active letter space for the
channel label.
Press the MENU ▲▼
buttons to move up and
down the Channel Label
list.
Press the MENU ▲ ▼
buttons to pick any of the
letters or symbols that are
given for your use.
Just stop on any label you
might want to use.
The selected label
Press the MENU ᮤ ᮣ
buttons to move the red
highlight to the other letter
spaces and repeat.
automatically appears with
channel changes and when
the STATUS button is
pressed.
Press the STATUS button
to clear the screen when
finished.
Press the STATUS button
to clear the screen when
finished.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG SOUND MENU CONTROLS
BASS, TREBLE, BALANCE
our DPTV also has individual
Ysound adjustment controls. The
BASS (low frequency), TREBLE
(high frequency) , and Speaker
BALANCE may all be used to
adjust the sound playback of NTSC
TV programs.
NTSC
ANALOG MAIN MENU
PICTURE
SOUND
BEGIN
FEATURES
SOUND MENU
BASS
1
Select BASS, or TREBLE, or
BALANCE sound control.
TREBLE
STEREO
EXIT
1 ST TIME SETUP
BALANCE
DISPLAY VOLUME
EXIT
With the SOUND MENU on-
screen, move the RED highlight
AVL
MORE...
with the MENU (M)
Then press the MENU button.
buttons.
1
OF 2
2
3
Press the MENU ᮤ ᮣ arrow
buttons to adjust the sound control
to levels you prefer.
mute
Press the “exit” button to clear
the screen.
1
channel
TV
+
menu
BASS
STOP
volume
+
MIN
MAX
M
EXIT
NEXT...
exit
Analog
4/4
DTV
1
2
Select and then press MENU
(M) button to view additional
controls grouped under same
feature heading. For
3
Example: Treble, Balance,
Stereo, etc.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG SOUND MENU CONTROLS
SMART
HELP
STEREO
our DPTV is able to receive
Ybroadcast stereo TV programs.
The DPTV is equipped with an
internal amplifier and speaker
system through which the stereo
sound can be heard.
Remember.
If a stereo signal is
not available and
the DPTV is placed
in STEREO, the
sound coming from
the unit will remain
monaural (mono).
NTSC
BEGIN
ANALOG MAIN MENU
PICTURE
SOUND
Select STEREO sound control.
1
FEATURES
SOUND MENU
BASS
With the SOUND MENU on-
screen, move the RED highlight
TREBLE
STEREO
EXIT
1 ST TIME SETUP
BALANCE
DISPLAY VOLUME
EXIT
with the MENU (M)
buttons.
AVL
Then press the MENU button.
MORE...
2
3
Press the MENU ▲▼ and
MENU (M) buttons to highlight
and turn ON (
ߜ ) the STEREO mode.
1
OF 2
Press the “exit” button to clear
mute
the screen.
1
hannel
TV
STEREO
1
STOP
menu
MONO AT ALL TIMES
STEREO IF AVAILABLE
volume
+
M
exit
EXIT
NEXT...
Analog
4/4
DTV
2
3
SECOND AUDIO PROGRAM
Second Audio Program (SAP)
is part of the stereo broadcast
system. Sent as a additional
audio channel SAP can be heard
apart from the current TV
NTSC
SOUND MENU
SECOND AUDIO PROGRAM
program sound. TV stations are
free to use SAP for any number
of purposes, but many experts
believe it will be used for foreign
language translations of TV
shows (or for weather and news
bulletins.)
SECOND PROGRAM SOUND CAN ONLY BE
SELECTED (
ߜ ) WHEN SAP INFORMATION IS PRESENT ON THE CURRENT CHANNEL.
MORE...
EXIT
2
OF 2
SECOND AUDIO PROGRAM
NORMAL SOUND
n
e
n
w
a
s
NOTE: If a SAP signal is not
present with a selected program,
the SAP option can not be
SECOND PROGRAM SOUND
s
a
n
w
e
EXIT
n
selected. "This program does not
contain SAP information" will
show on the DPTV screen.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG SOUND MENU CONTROLS
DISPLAY VOLUME
se the DISPLAY VOLUME
Ucontrol to see program
volume level settings on the DPTV
screen. Once set, the Volume
Display will be seen each time the
VOLUME buttons (on the DPTV
local keyboard or Pronto remote)
NTSC
ANALOG MAIN MENU
PICTURE
are pressed.
BEGIN
SOUND MENU
BASS
SOUND
TREBLE
STEREO
1
Select DISPLAY VOLUME
control.
FEATURES
BALANCE
DISPLAY VOLUME
EXIT
1 ST TIME SETUP
EXIT
AVL
With SOUND MENU on-screen,
move the RED highlight with the
MORE...
MENU (M)
buttons. Then
1
OF 2
press the MENU button.
Press the MENU ▲▼ and
MENU (M) buttons to highlight
and turn ON (
ߜ ) the DISPLAY VOLUME control.
2
DISPLAY VOLUME
NEVER
mute
1
3
Press the “exit” button to clear
the screen.
annel
TV
1
DURING ADJ USTMENT
menu
volume
+
STOP
EXIT
NEXT...
M
exit
Analog
4/4
DTV
2
3
21
Download from Www.Somanuals.com. All Manuals Search And Download.
M
AIN
M
ENU
P
ICTURE
S
OUND
FEATURES
1
S
T
TIM
E
S
ETUP
EXIT
NTSC ANALOG SOUND MENU CONTROLS
AUTOMATIC VOLUME
LIMITER
re you tired of the sound of
Acommercials following you
into the next room or all through
the house? The Automatic Volume
Limiter (AVL) control allows you
to preset a desired volume level
that the DPTV sound will not go
above. This makes for an even,
more consistent sound by reducing
the “peaks” and “valleys” that can
occur during program changes or
commercial breaks.
NTSC
ANALOG MAIN MENU
PICTURE
SOUND
SOUND MENU
BASS
TREBLE
STEREO
FEATURES
BALANCE
DISPLAY VOLUME
EXIT
1 ST TIME SETUP
EXIT
AVL
MORE...
BEGIN
Select AVL (Automatic Volume
Limiter) control.
1
OF 2
1
With SOUND MENU on-screen,
move the RED highlight with the
MENU (M)
buttons. Then
press the MENU button.
AVL
ON
2
mute
1
2
Press the MENU ▲ or ▼ and
then the MENU (M) button to turn
the AVL control ON (or OFF).
annel
TV
1
OFF
menu
volume
+
EXIT
NEXT...
M
3
Press the “exit” button to clear
the screen when completed.
exit
Analog
4/4
DTV
2
STOP
3
SMART HELP
Remember, AVL works
for sound levels coming
from either the Antenna/Cable
input on the rear of the DPTV (RF
audio) or the Auxiliary
(VCR/AUX IN) audio inputs.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PRONTO REMOTE NTSC ANALOG FEATURES
PRONTO - ANALOG TV MODE
alternate audio
Primarily used for “alt audio” ATSC mode
feature, this button can also be used to
quickly select the NTSC Second Audio
he Pronto remote contains four
Tdisplay screens of “analog TV”
related controls. Use the
Program (SAP) feature (when available).
touchscreen controls to access and
adjust NTSC features for Input
selection; Menu feature
status button
Press to see the current channel number on the DPTV screen.
Also press to clear the DPTV screen after control adjustments.
power button
Press to turn the DPTV ON and OFF.
adjustments; and Guide Plus+
program functions.
mute button
Press to turn the sound OFF on the DPTV. Press again to return
the sound to its previous level.
Note: For battery installation and
other details on the initial use of
the Pronto remote control also
refer to the 64PP9901 Quick Use
guide included with your DPTV.
mute
channel scan buttons
Press to scan up (+) or down (-) through any NTSC programmed
channel numbers.
channel
TV
+
power
alt audio
sleep
status
dtv freeze
ext input
volume
volume buttons
Press to adjust the DPTV sound level up (+) and down (-).
+
BEGIN
analog TV
1
DTV
Gently tap the Pronto
ext input button
touchscreen with your finger to
display its control panel for use.
Press to quickly select NTSC auxiliary input modes
(AUX1/2/3), as well as cycle through the DPTV’s other
input option modes (Monitor VGA, EXT HD, etc.).
Analog
1/4
DTV
TV
Be sure “TV” is selected for the
current device tab item category.
number buttons
Press the number buttons to select DPTV channels. Press
two number buttons to select single digit “major” channel
numbers. For example: press "0" then "6" for channel 6.
Press the “analog TV” button
on the Pronto to ensure NTSC
mode commands are sent from the
remote.
2
sleep button
Press to set the DPTV to
automatically turn itself OFF.
(15 minutes to 2 hours ahead.)
A/CH
Analog
2/4
DTV
TV
TV Guide Plus + buttons
STOP
red
Press to operate the on-screen TV
Guide Plus+ program system. Refer
to your separate TV Guide Plus+
Setup and Users manual for
operating details on the color coded
button functions and system setup
options.
A/CH button
Press Alternate Channel (A/CH) to select previously
viewed channels. Enter the desired two channel numbers
(from the Pronto remote’s number buttons), and then
press A/CH to toggle back and forth between the two
channel selections.
yellow
green
blue
on/off
SMART HELP
setup
info
Due to the amount of
optional component and
record
Analog
3/4
DTV
feature uses available with the
Pronto’s Device Reference and
Learn Code lists, please also refer
to the separate full-use Pronto
Owner’s Manual for complete
details on its function and
operations.
TV
menu
buttons
menu
Press the Menu (or M) button to show on-screen
controls. Press M ▲ or ▼ buttons to move up (or
down), the M ᮤ or ᮣ to move left (or right) through
the list of controls.
M
exit
exit button
Press to clear the DPTV screen after control
adjustments. Also press to see the current channel
number on the DPTV screen.
Analog
4/4
DTV
scroll arrows
Press to move to the next (or previous) page of Pronto
controls. The touchscreen will display the current
control screen’s page number, and the total number of
pages available for the selected device (1/4; 2/4; etc.)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO/VIDEO NTSC ANALOG CONNECTIONS
AUX1/2 INPUTS
he Analog Audio/Video Input
Tjacks are for direct NTSC
picture and sound connections
between the DPTV and auxiliary
equipment (VCR, DVD Player,
etc.) that has Audio/Video Output
jacks.
PICTURE AND SOUND FROM
PLAYBACK OF VCR TAPE
REAR OF DPTV
AUX 1
NTSC
2
1
ANALOG
AUDIO INP
AUX
AUDIO OUT
1
ANALOG
To view the playback of a VCR
tape by using the Analog AUX1
Audio/Video Input jacks:
BEGIN
L
L
TV ANT/CABLE
R
R
TV
IR BLASTER
S-VIDEO
VIDEO INPUT
VIDEO OUT
AUX
1
AUX
2
1
Connect the VIDEO OUT jack
from the VCR to the AUX 1
VIDEO IN jack on the DPTV.
VIDEO IN
(YELLOW)
AUDIO IN
(RED/WHITE)
2
Connect the AUDIO OUT
jacks R(ight) and L(eft) from the
VCR to the AUX 1 AUDIO IN
jacks on the DPTV.
OUT
ANTENNA
IN
OUT
OUT
AUDIO/VIDEO
OUTPUT JACKS
ON VCR
VIDEO
IN
L
R
AUDIO
IN
3
mute
Press the “ext input” button
on the Pronto (or the Source button
on the DPTV’s local keyboard) to
select the AUX 1 Audio/Video
Inputs on the rear of the DPTV.
4
channel
TV
+
power
alt audio
sleep
status
dtv freeze
ext input
volume
+
analog TV
DTV
4
Turn the VCR ON and press
PLAY to view the tape playback
on the DPTV.
VCR
3
Analog
1/4
DTV
If you have a single (monaural)
Audio Output VCR, "Y" connectors
are available to complete your
connection. Contact your dealer, or
our Parts Information Center (1-
800-292-6066) to order any optional
accessories.
STOP
SMART HELP
Remember, connections
and use of the DPTV's
AUX 2 Audio/Video Input jacks
are the same as for the AUX 1
jacks (except "AUX 2" is selected
as the Input Source in step 3).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO/VIDEO NTSC ANALOG CONNECTIONS
AUX 3 INPUTS
or more convenient Direct
Fplayback connections the
DPTV's Front Audio/Video Input
panel can be used. Located on the
DPTV's right front side panel
these Input jacks allow for quick
and easy connections, particularly
for the playback of Camcorder
tape recordings.
PICTURE AND SOUND FROM PLAYBACK
OF CAMCORDER TAPE
AUX 3
NTSC
FRONT AUDIO/VIDEO JACKS
AUX3 Inputs located on right
front side panel of DPTV.
To view the playback of a
Camcorder recording using the
AUX3 Analog Audio/Video Input
jacks:
AUX3
UP
CH
VIDEO IN
VOL
–
+
SOURCE
M
EXIT
VOL
CH
BEGIN
DOWN
L
AUDIO IN
1
2
Connect the VIDEO OUT jack
from the Camcorder to the AUX3
VIDEO IN jack on the DPTV.
R
1
2
Connect the AUDIO OUT
jacks R(ight) and L(eft) from the
Camcorder to the AUX3 AUDIO
IN jacks on the DPTV.
mute
AUDIO IN
4
channel
(RED/WHITE)
TV
status
+
VIDEO IN
power
volume
(YELLOW)
alt audio
sleep
dtv freeze
ext input
+
3
4
Press the “ext input” button
on the Pronto (or the Source button
on the DPTV’s local keyboard) to
select the AUX3 Audio/Video
Inputs on the right side of the
DPTV.
analog TV
DTV
3
Analog
1/4
DTV
AUDIO/VIDEO
OUTPUT JACKS
ON CAMCORDER
CAMCORDER
Turn the Camcorder ON and
press PLAY to view the tape on
the DPTV.
If you have a single (monaural)
Audio Output Camcorder, "Y"
connectors are available to complete
your connection. Contact your
dealer, or our Parts Information
Center (1-800-292-6066) to order
any optional accessories.
STOP
25
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO/VIDEO NTSC ANALOG CONNECTIONS
AUX1 - S-VIDEO INPUTS
he S(uper)-Video connections
Ton the rear of the DPTV offer
improved picture detail and clarity
for the playback of S-VHS VCR
tapes or DVDs over a standard
composite video input connection.
PICTURE AND SOUND FROM PLAYBACK OF S-
VHS VCR TAPE PLAYBACK
REAR OF DPTV
S VIDEO
NTSC
2
ANALOG
Note: The VCR (or DVD Player)
must have a S-VIDEO OUT(put)
jack in order for you to complete the
connections shown on this page.
AUDIO INPUT
AUX AUX
AUDIO OUT
1
2
1
ANALOG
L
L
TV
R
R
TV
IR BLASTER
S-VIDEO
VIDEO INPUT
VIDEO OUT
AUX
1
AUX
2
BEGIN
Connect the S-VIDEO (S-
VHS) OUT jack from the VCR to
the AUX1 S-VIDEO input plug on
the DPTV.
1
S-VIDEO
CABLE
AUDIO OUT
(RED/WHITE)
S-VIDEO OUT
OUT
OUT
OUT
VIDEO
IN
OUT
The S-VIDEO connecting cable
will be supplied with the S-VHS
VCR (or DVD Player).
S-VIDEO
ANTENNA
L
R
AUDIO
IN
IN
mute
Connect the AUDIO OUT
jacks R(ight) and L(eft) from the
S-VIDEO VCR to the AUX1
AUDIO input jacks on the DPTV.
2
3
channel
4
TV
+
power
status
dtv freeze
ext input
volume
alt audio
sleep
+
analog TV
DTV
Press the “ext input” button
on the Pronto (or the Source button
on the DPTV’s local keyboard) to
select the S VIDEO input on the
DPTV.
3
S-VHS VCR
Analog
1/4
DTV
NOTE: A CD-i (Compact Disc Interactive)
player, Video Game, or other S-VIDEO
accessory can be hooked up to the DPTV
using this type of connection. Please be aware
that such video sources, which show a
constant non-moving pattern on the DPTV
screen, can cause picture tube damage. When
not in use turn your video accessories OFF.
Also, regularly alternate the use of video
sources with normal TV program viewing.
Note: The "S VIDEO" picture
source option appears only when a
S-VIDEO cable has been connected
to the DPTV.
Turn the VCR ON and place it
in the S-VIDEO (or S-VHS)
playback mode. Insert S-VHS
cassette tape and playback in a
normal manner.
4
STOP
SMART HELP
Remember, connections
and use of the DPTV's S-
VIDEO AUX2 Input plug is the
same as for the S-VIDEO AUX1
input (except "S-VIDEO 2" is
selected as the Picture Source in
step 3).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO/VIDEO NTSC ANALOG CONNECTIONS
AUDIO/VIDEO OUTPUTS
he Audio/Video Output jacks
Ton the DPTV can be used to
record TV programs on VCRs
which have Audio/Video Input
jacks.
PICTURE AND SOUND BEING RECORDED ON
VCR.
REAR OF DPTV
NTSC
2
1
ANALOG
To record TV programs by using
the Audio/Video Output jacks on
the DPTV:
AT
X
AUDIO OUT
2
ANALOG
L
L
TV ANT/CABLE
R
R
TV
IR BLASTER
BEGIN
S-VIDEO
VIDEO INPUT
VIDEO OUT
AUX
1
AUX
2
1
2
Connect the VIDEO OUT jack
from the DPTV to the VIDEO IN
jack on the VCR.
AUDIO
OUT
(RED/
VIDEO OUT
(YELLOW)
Connect the AUDIO OUT
jacks R(ight) and L(eft) from the
DPTV to the AUDIO IN jacks on
the VCR.
WHITE)
OUT
ANTENNA
IN
OUT
OUT
AUDIO/VIDEO INPUT
JACKS ON VCR
VIDEO
IN
L
R
AUDIO
IN
3
Press the “ext input” button
on the Pronto (or the Source button
on the DPTV’s local keyboard) to
place the DPTV in the NTSC
mode.
mute
4
channel
TV
+
power
alt audio
sleep
status
dtv freeze
ext input
volume
+
Select the channel on the DPTV
that you want to record.
analog TV
DTV
3
Analog
1/4
DTV
VCR
Turn the VCR ON. Put a
cassette tape in the unit and place
the VCR in the RECORD mode.
4
STOP
SMART HELP
Remember, if the VCR
has an INPUT SELECTOR
switch, place it in the LINE or
CAMERA position.
Unattended Timer Recordings
with a VCR are possible, but not
recommended with this
connection since the DPTV must
be left ON for the VCR to record.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO/VIDEO NTSC ANALOG CONNECTIONS
SYSTEM AUDIO OUTPUTS
The System Audio Out(put) jacks send the DPTV’s current audio
(ATSC, NTSC, or Monitor) to an external amplifier for output. The
advantage of such an additional System Audio Out connection (as
shown in this diagram) is that it could continue to route the supplied
audio signals from the DPTV to an external amplifier or Pro Logic
Receiver (even when the selected program source switches between a
digital ATSC program, NTSC, or Monitor supplied source). In the case
of digital multichannel audio the DPTV downmixes the audio output to a
straight 2-channel stereo signal.
he DPTV's System Audio
TOutput jacks can be used for
sound playback through an
external audio amplifier or Dolby
Pro Logic receiver.
BEGIN
Note: For best audio reproduction and playback of Dolby Digital
surround sound through a Pro Logic Receiver (when using the
System Audio Out jacks):
• place the REAR SPEAKER DELAY control (located in the DPTV’s
ATSC Speakers Menu) to the maximum 13 feet/4 meters setting
• place the Center Channel Delay control (located in the DPTV’s
ATSC Speakers Menu) to the “Center Back” position.
Connect the R(ight) and L(eft)
SYSTEM AUDIO OUT jacks on
the DPTV to the R and L Audio
Input jacks on your amplifier or
sound system.
1
REAR OF DPTV
2
Turn DPTV ON and place the
external amplifier system to the
AUX INPUT mode (if applicable).
L
R
SYSTEM AUDIO OUT
STEREO IN
Note: Dependent upon the audio
information received the DPTV
outputs a straight two channel
Left/Right stereo audio signal for
output.
C
6 CHANNEL
AUDIO IN
RS
LS
SW
R
L
SYSTEM AUDIO OUT
STEREO IN
C
6
CHANNEL
AUDIO IN
RS
LS
SW
DTV ANTENNA
V
G
A
I
N
INTERNAL TV SPEAKERS
USED AS CENTER
CHANNEL
FRONT
SPEAKERS
EXT
INT
DTV DIGITAL
AUDIO OUT
SUBWOOFER
PREAMP OUT
N
O
Y
E
S
7
5
o
h
m
SYNC
HIGH
CENTER
CHANNEL INPUT
SUBWOFER
SPEAKER OUT
H/H
V
+
V
–
–
+
+
50
W
M
A
X
I
N
FRONT EXTERNAL SPEAKERS OUT
STOP
R/Pr
G/Y
R
–
–
+
L
+
SURROUXTERNAL SPEAKOUT
ANALOG
AUDIO OUT
AUDIO INPUT
AUX AUX
1
2
ANALOG
R
–
–
+
L
+
L
L
B/Pb
All External Speakers
8
ohms Min.
TV ANT/CABLE
R
R
TV
IR BLASTER
HD COMPONENT
VIDEO IN
S-VIDEO
AU
VIDEO T
VIDEO INPUT
AUDIO INPUT JACKS
SMART HELP
R
L
Note: To eliminate sound
playback through the DPTV
cabinet speakers when using an
external amplifier audio connection
you can either:
AUDIO INPUT
PHONO INPUT
-Press the MUTE button on the
Pronto remote to eliminate sound
through the DPTV speakers
OR
-Place the FRONT SPEAKERS
switch on the rear of the DPTV
to the EXT(ernal) position
(which will also eliminate the
use of the Front External
AUDIO SYSTEM (or Dolby Pro Logic Receiver )
SPEAKERS USED FOR PLAYBACK SOUND
Speaker Out connection
terminals on the DPTV.)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL ON-SCREEN MENU FEATURES
E
xit
DTV SETUP (AUTOPROGRAM)
nce connected to receive
Odigital ATSC broadcast
signals, available area channels
can be added into the DPTV’s
channel scan memory by the use of
the DTV Setup Menu.
Press the Pronto remote’s “DTV” (or the “Source”
button on the DPTV’s local keyboard) to select the
ATSC operating mode.
ATSC
Note: Refer to the 64PP9901
Quick Use guide for additional
information on digital channel
programming and direct ATSC
channel selections or access.
BEGIN
DTV Main Menu
Picture
Sound
Speakers
Features
DTV Setup
Exit
DTV Setup
W ould you like to program DTV channels ?
This proces s m ay take s everal m inutes .
Select DTV Setup control.
1
With the DTV Main Menu on-
screen, move the highlight with the
MENU (M) ▲▼ buttons. Then
press the MENU button.
Yes , add new channels
Yes , full ins tallation
No
2
3
Press the MENU ▲▼ buttons
to select the Full Installation
option, then press the Menu button.
2
1
mute
channel
TV
+
Press the MENU ▲▼ buttons
to select the “With” (or “Without”)
Program and System Information
option for autoprogramming, and
then press the Menu button.
Note: See the Program and System
Information box to the right for
further explanation and details on
PSIP and how it is to be used.
Full Ins tallation
Ins tall with Program and Sys tem Info
Ins tall without Program and Sys tem Info
menu
volume
+
M
Cancel
exit
Analog
4/
DTV
1
2
3
The DPTV shows an Installing
indicator bar on-screen as the
digital channels are added into
scan memory.
Program and System Information (PSIP)
• Standards were devised as part of the ATSC system
to allow TV stations to transmit Program Service
Information Protocol (or PSIP) for DTV channels.
This information system would allow stations to
broadcast various electronic on-screen program
guides in order to inform digital TV viewers of
station channel locations and availability of
programs.
Not all initial digital broadcast programs contain, or
will be available with, the PSIP program guides. The
64PP9901 DPTV provides two separate Full
Installation digital channel autoprogramming options,
based on whether PSIP information is present or not.
You may want to initially use the “Install Without
Program and System Info” option in order to display
and program the DTV channels, and avoid any
difficulties in first time setup or autoprogramming of
the DPTV.
Auto Program
Autoprogram m ing in progres s .
This m ay take s everal m inutes .
"DTV Setup Complete" shows
when the DPTV is through adding
digital channels into memory.
Cancel
Ins talling
4
Press the “exit” (or Menu)
button to clear the screen.
SMART HELP
Note: With the “full
installation” Auto Program
DTV Setup Com plete
option the DPTV rewrites its entire
digital channel scan “map”
currently held in memory.
The “add new channels” Auto
Program option allows you to retain
the current DPTV channel scan
memory map, and include only the
new digital channel stations as they
become available for selection.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL PICTURE MENU CONTROLS
E
xit
COLOR, BRIGHTNESS,
SHARPNESS, TINT, PICTURE
o adjust your ATSC color and
Tpicture controls, select a digital
channel and follow the steps shown
below:
ATSC
BEGIN
1
Select the ATSC Picture
Menu.
DTV Main Menu
Picture
Sound
Speakers
Features
DTV Setup
With the DTV Main Menu on-
screen, move the highlight with
the MENU (M) ▲▼ buttons. Then
press the MENU button.
Picture Menu
Exit
Color
Brightnes s
Sharpnes s
Picture
Tint
Convergence
Press the Menu ᮤ or ᮣ arrow
buttons to adjust the selected
picture or color control.
2
3
Back
Control settings are at normal mid-range levels when
the bar scale is centered.
Press the Menu (M) ▲▼ buttons
to move up and down the list of on-
screen Picture controls.
mute
1
channel
Press the “exit” button to clear
the screen.
TV
+
menu
volume
+
STOP
M
exit
Analog
4/4
DTV
SMART HELP
1
2
3
Color Press (M) ᮤ or
ᮣ to add or eliminate
color.
Brightness Press (M) ᮤ or ᮣ
until dark parts of the picture show
good detail.
Sharpness Press (M) ᮤ or ᮣ to
improve detail in the picture.
Picture Press (M) ᮤ or ᮣ until
whitest parts of the picture are as
bright as you prefer.
Tint Press (M) ᮤ or ᮣ to obtain
natural skin tones.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL PICTURE MENU CONTROLS
E
xit
RED/BLUE CONVERGENCE
onvergence is the correct
Clining up of the red and blue
light paths on the DPTV screen.
NOTE: If no color fringing (see
Smart Help) shows, then no
Convergence adjustments are
necessary.
ATSC
DTV Main Menu
Picture
BEGIN
Sound
Speakers
Features
DTV Setup
Select the ATSC Convergence
control.
1
Picture Menu
Exit
Color
With Picture Menu on-screen,
move the highlight with the
MENU (M) ▲▼ buttons. Then
press the MENU button.
Brightnes s
Sharpnes s
Picture
Tint
Convergence
Back
2
3
Press the MENU ▲▼ buttons
to select either the Align Red or
Align Blue Convergence control,
press the MENU button to
continue.
2
1
mute
channel
TV
+
Press the MENU
buttons
menu
Convergence
volume
to move the selected red (or blue)
convergence cross directly over the
white cross on the DPTV screen.
+
Align Red
Align Blue
M
Back
exit
The red (or blue) cross is properly
adjusted when it is completely
merged with the white cross. (No
color appears around the edge of
the white cross).
4/4
Analog
DTV
1
2
3
4
Press the “exit” button to clear
the screen when convergence
adjustments are complete.
4
Press
to align RED
Press MENU to Return
STOP
SMART HELP
Remember, Convergence
has been set at the factory for
best viewing, but if one or more of
the (red or blue) colors appear
around the edges of objects (color
fringing) follow the steps given in
this section.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ATSC DIGITAL SOUND MENU CONTROLS
SURROUND SOUND
REAR OF DPTV
y adding optional external
Bspeakers to the DPTV's sound
system, you can create the feeling
of reflected sound that surrounds
you at a movie theater or concert
REAR SURROUND SOUND
SPEAKER TERMINALS
(Operational only in ATSC or
Monitor Diplay modes)
hall.
1
BEGIN
SURROUND EXTERNAL SPEAKERS OUT
1
2
Connect both external
speakers to the speaker wire
terminals on the DPTV.
–
–
+
+
R
L
R
L
Recommended speakers: 25W, 8
ohm minimum. Be sure the (+) and
(-) speaker wires are connected to
the correct R(ight) and L(eft)
SYSTEM AUDIO OUT
STEREO IN
C
6
CHANNEL
AUDIO IN
All External Speakers
25W, 8 ohms Min.
RS
LS
SW
DTV ANTENNA
V
G
A
I
N
INTERNAL TV SPEAKERS
USED AS CENTER
CHANNEL
FRONT
SPEAKERS
EXT
T
DTV DIGITAL
AUDIO OUT
SUBWOOFER
PREAMP OUT
N
O
Y
E
S
7
5
o
h
m
SYNC
HIGH
CENTER
CHANNEL INPUT
SU
SPEAKER OUT
H/H
V
+
V
–
–
+
+
50
W
M
A
X
I
N
FRONT EXTERNAL SPEAKERS OUT
R
–
–
+
L
+
R/Pr
G/Y
SURROUND EXTERNAL SPEAKERS OUT
ANALOG
AUDIO OUT
AUDIO INPUT
AUX AUX
1
2
ANALOG
R
–
–
+
L
+
L
L
B/Pb
All External Speakers
8
ohms Min.
TV ANT/CABLE
R
R
TV
IR BLASTER
HD COMPONENT
VIDEO IN
S-VIDEO
AUX
AU
2
VIDEO OUT
VIDEO INPUT
speaker terminals on the DPTV.
Place the speakers so the
viewing area is between the DPTV
and the rear surround speakers.
(See overhead view drawing on
this page.)
3
+
-
Turn DPTV ON. After setup
whenever a stereo signal is
received the audio will be heard in
Surround Sound.
+
-
STOP
REAR SURROUND SOUND SPEAKERS
• Note: Surround Sound will not work with only
one speaker connected; or with monaural audio
playback source
SMART HELP
Note: The rear Surround
Sound speakers will not be
heard at the same volume level as
the front DPTV speakers. It is
intended for the rear speakers to
give a background noise effect
which requires a lower volume
level than the DPTV's front
speakers.
DPTV
2
REAR SPEAKER
REAR SPEAKER
PRIMARY VIEWING AREA
32
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL SOUND MENU CONTROLS
E
xit
SURROUND SOUND
he Surround Sound control
Toption allows you to select the
type of sound mode sent to the
DPTV’s speaker system.
ATSC
DTV Main Menu
Picture
Sound
Speakers
Features
BEGIN
Select the ATSC Sound Menu.
1
Sound Menu
Surround Mode Surround
Treble
Bas s
DTV Setup
With DTV Main Menu on-screen,
move the highlight with the MENU
(M) ▲▼ buttons. Then press the
MENU button.
Stereo
Exit
Auto Volum e
ON-compressed
Back
Press the MENU ▲▼ buttons
to select the Surround Mode
control.
2
3
Surround Mode -
• Dolby Digital 5.1 sound is processed normally
directing discrete channel audio sound to 6 speakers
(DPTV Front Right/Center/Left speakers; two rear
Surround speakers; and one Subwoofer low
frequency speaker.)
• For any two channel plain stereo audio (arriving
within the ATSC Dolby Digital carrier signal) the
DPTV processes the audio to play standard stereo in
the Left/Right Front DPTV speakers only.
2
1
mute
channel
TV
+
Press the Menu ᮤ or ᮣ
buttons to select the Surround (or
Stereo) mode for DPTV sound
playback.
3
ume
+
menu
M
(See the Surround Sound
information box to the right for
further details on the feature and its
use.)
Stereo Mode -
• Left/Right audio input signals are directed to the
DPTV’s two front L/R speakers.
• ATSC Dolby Digital multichannel sound signals are
downmixed to two channels and sent to the Front
Left/Right DPTV speakers. This is to avoid audio
distortion on any non-Dolby pseudo-surround
programming that may be received.
exit
Analog
4/4
DTV
1
2
4
4
Press the “exit” button to clear
the screen.
STOP
REAR OF DPTV
Subwoofer
Speaker
- (powered) -
Suggested or
equivalent
optional
subwoofer
speakers for
use:
• Velodyne -
VAIC120
(12”, 120W)
• Infinity -
INI BU120
(12”, 120W)
• JBL -
INTERNAL TV SPEAKERS
USED AS CENTER
FRONT
CHANNEL
SPEAKERS
EXT
INT
DOLBY DIGITAL SURROUND
SUBWOOFER
PREAMP OUT
NO YES
CENTER
CHANNEL INPUT
SUBWOOFER
SPEAKER OUT
Sound Menu
n order to receive the full
Surround Mode
Treble
Surround
–
+
–
+
50
W
MAX IN
FRONT EXTERNAL SPEAKERS OUT
Bas s
Auto Volum e
Ireproduction capability of true
Dolby Digital Surround Sound
you require the proper use and
arrangement of a Subwoofer and
surround speakers. The DPTV’s
extra speaker connections make it
possible to create a multichannel
soundfield effect previously
ON-compressed
–
–+
+
R
L
SURROUND EXTERNAL SPEAKERS OUT
Back
–
–+
+
R
L
All External Speakers
8
ohms Min.
UP
CH
SOURCE
VOL
–
M
+
EXIT
VOL
CH
DOWN
PSWD110
(10”, 100W)
available only within a movie
theater or concert hall. With the
new 5.1 discrete digital channel
surround sound system the listener
can now attain a true soundstage
realism for audio signal
separation, imaging, and pinpoint
sound placement.
Note: If the Front External
Speaker Out terminals are used for
Left/Right audio channel playback
of Dolby Digital material, the
FRONT SPEAKER slide switch on
the rear of the DPTV must also be
placed to the EXT(ernal) position
in order for the connection and
signal routing to operate properly.
Front External
Speaker
(25W, 8Ω Min.)
Front External
Speaker
(25W, 8Ω Min.)
• Left/Right Front External speakers can be used in substitution
for the DPTV internal cabinet speakers if desired. (See the “Front
Speakers Switch” note in the section to the left for an explanation.)
• Subwoofer speaker connections are available on the rear of the
DPTV for either powered, or non-powered, types of optional
Subwoofer speakers. Contact your Philips dealer for further details
on Dolby Digital Surround Sound system speakers and their use.
Subwoofer
Speaker
- (nonpowered) -
25W, 8Ω Min.
• Ask your dealer
about subwoofer
and surround
sound speakers
suggested for use
with your your
TV.
Rear Surround
Speaker
Rear Surround
Speaker
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL SOUND MENU CONTROLS
E
xit
DOLBY DIGITAL SURROUND
ADDITIONAL CONNECTIONS
REAR OF DPTV
Center Channel Input terminal
Ais also located on the rear of
the DPTV for additional Dolby
Digital Surround sound connection
options. This input can be used to
connect an external Dolby Digital,
or Home Theater Surround Sound,
capable Amplifier (with Center
Channel output) in order to play
Center Channel sound through the
DPTV’s internal cabinet speakers.
INTERNAL TV SPEAKERS
USED AS CENTER
CHANNEL
FRONT
SPEAKERS
EXT
INT
SUBWOOFER
PREAMP OUT
NO YES
CENTER
CHANNEL INPUT
(50W Max. Input)
SUBWOOFER
SPEAKER OUT
–
+
MAX IN
–
+
50
W
FRONT EXTERNAL SPEAKERS OUT
–
–+
+
R
L
SURROUND EXTERNAL SPEAKERS OUT
R
L
SYSTEM AUDIO OUT
STEREO IN
C
6
CHANNEL
AUDIO IN
RS
SW
–
–+
+
R
L
DTV ANTENNA
V
G
A
I
N
INTERNAL TV SPEAKERS
USED AS CENTER
CHANNEL
FRONT
SPEAKERS
EXT
INT
DTV DIGITAL
AUDIO OUT
SUBWOOFER
PREAMP OUT
N
O
Y
E
S
75 ohm
HIGH
SYNC
SUBWOOFER
SPEAKER OUT
NER
CHANNEL INPUT
H/H
V
+
V
–
–
+
+
MAX IN
50
W
All External Speakers 8 ohms Min.
FRONT EXTERNAL SPEAKERS OUT
R/Pr
G/Y
R
–
–
+
L
+
ANALOG
SURROUND EXTERNAL SPEAKERS OUT
A
U
D
I
O
O
U
T
AUDIO INPUT
AUX AUX
1
2
–
–
+
+
ANALOG
R
L
L
L
B/Pb
All External Speakers
8
o
h
m
s
M
i
n
.
TV ANT/CABLE
R
R
TV
IR BAE
HD COMPONENT
VIDEO IN
S-VIDEO
AU
V
I
D
E
O
O
V
I
E
O
I
N
T
For example: With the use of an
external Amplifier capable of
Dolby Digital 5.1 (or Home
Theater Surround Sound) the Front
(Left/Right), Center, and Rear
(Left/Right) Surround system
speakers have their signals
supplied by the connections located
on the rear of the Amplifier.
Note: When an external
SURROUND
SPEAKERS
CENTR CH
OUT
+ R -
- L +
_
+
_
Amplifier is used as the audio
playback source for the DPTV’s
Center Channel Input terminals:
• Place the DPTV’s “INTERNAL
TV SPEAKERS USED AS
CENTER CHANNEL” switch
and the “CENTER CHANNEL
INPUT” switch to the YES
position in order for the
Right Front
External
Speaker
Left Front
External
Speaker
External Amplifier
(capable of Dolby Digital
5.1 or Home Theater
Surround Sound
Reproduction)
+
-
+
-
connection and Center Channel
speaker playback to function
properly.
These two slide switches are
used in tandem and should both
be kept in either the YES
Rear Surround
Speakers
position (when the DPTV is used
for Center Channel Input
playback), or the NO position
(when the DPTV uses its own
internal speaker system for
Surround sound purposes).
REAR OF DPTV
SYSTEM AUDIO OUTPUT JACKS
R
L
Note: The Left/Right Audio Out jacks
send the current available system audio
(whether NTSC, ATSC, or Monitor) for
output to an external amplifier. In the
case of digital multichannel audio the
DPTV downmixes the audio output to a
straight 2-channel stereo signal.
SYSTEM AUDIO OUT
STEREO IN
C
6
CHANNEL
AUDIO IN
RS
LS
SW
R
L
SYSTEM AUDIO OUT
STEREO IN
C
6
CHANNEL
AUDIO IN
RS
LS
SW
SONY-PHILIPS DIGITAL INTERFACE FORMAT
DTV ANTENNA
V
G
A
I
N
INTERNAL TV SPEAKERS
USED AS CENTER
CHANNEL
FRONT
SPEAKERS
EX
N
DTV DIGITAL
AUDIO OUT
SUBW
PREAMP OUT
N
S
7ohm SYNC
IGH
SUBWOOFER
SPEAKER OUT
CENTER
CHANNEL INPUT
H/H
V
+
V
–
–
+
+
MAX IN
50
W
F
R
O
N
T
E
X
T
E
R
N
A
L
S
P
E
A
K
E
R
S
O
U
T
R/Pr
G/Y
R
–
–
+
L
+
ANALOG
S
U
R
R
O
U
N
D
E
X
T
E
R
N
A
L
S
P
E
A
K
E
R
S
O
U
T
A
U
D
I
O
O
U
T
AUDIO INPUT
AUX AUX
1
2
–
–
+
+
ANALOG
R
L
L
L
B/Pb
A
l
l
E
x
t
e
r
n
a
l
S
p
e
a
k
e
r
s
8
o
h
m
s
M
i
n
.
T
V
A
N
T
/
C
A
B
L
E
R
R
TV
IR L
HD COMPONENT
VIDEO IN
VIDEO
AUX
1
AUX
2
V
I
D
E
O
O
U
T
V
I
D
E
O
I
N
P
U
T
SPDIF is the term used for ATSC
module digital audio that can be
routed to an auxiliary amplifier that
accepts such an input signal. The
DTV Digital Audio Out(put) jack
on the rear of the DPTV is for the
connection of SPDIF audio
DIGITAL AUDIO
SPDIF INPUT
R
L
DTV DIGITAL
AUDIO OUT
AUDIO INPUT
PHONO INPUT
DTV DIGTIAL
AUDIO OUTPUT (SPDIF)
RCA PHONO PLUG CONNECTOR
(SPDIF is active only when the DPTV is
in the ATSC mode)
compatible external amplifiers or
home theater equipment.
AMPLIFIER/RECEIVER
(SPDIF INPUT CAPABLE)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL SOUND MENU CONTROLS
E
xit
BASS, TREBLE
he DPTV also has individual
Tsound adjustment controls for
the ATSC system audio. The BASS
(low frequency) and TREBLE
(high frequency) controls may be
used to adjust the sound of ATSC
TV programs, or other external
playback source material.
BEGIN
ATSC
DTV Main Menu
Picture
Sound
Speakers
Features
Sound Menu
DTV Setup
Surround Mode
Surround
Treble
Bas s
Exit
Auto Volum e
ON-compressed
Select Bass or Treble sound
control.
1
Back
With the Sound Menu on-screen,
move the highlight with the
MENU (M) ▲▼ buttons. Then
press the MENU button.
Treble and Bass are set to factory midpoint or default
levels when the barscale adjustments are placed to the
center detent position.
mute
1
channel
TV
+
2
+
Press the MENU ᮤ ᮣ arrow
buttons to adjust the sound control
to levels you prefer.
menu
2
3
M
exit
Press the “exit” button to clear
the screen.
Analog
4/4
DTV
1
STOP
3
AUTO VOLUME
erforming a function similar to
Pthe AVL sound control (in the
NTSC operating mode) the Auto
Volume control applies certain
value levels to variables within the
Dolby standard in order to achieve
dynamic audio range compression.
This single value setting by the
Auto Volume control allows for a
more consistent, even sound
reproduction in the playback of
ATSC audio.
ATSC
DTV Main Menu
Picture
Sound
Speakers
Features
Sound Menu
DTV Setup
Surround Mode
Treble
Surround
Exit
Bas s
Auto Volum e
ON-compressed
Back
BEGIN
Select Auto Volume sound
control.
1
mute
1
With the Sound Menu on-screen,
move the highlight with the
MENU (M) ▲▼ buttons. Then
press the MENU button.
channel
TV
+
2
um
+
menu
M
exit
Press the MENU ᮤ ᮣ arrow
buttons to turn the Auto Volume
control to ON-compressed (or
select Full Range to receive a non-
compressed ATSC audio signal).
2
3
Analog
4/4
DTV
1
3
Press the “exit” button to clear
the screen.
STOP
35
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL SPEAKERS MENU CONTROLS
E
xit
SPEAKERS
he Speakers Menu involves
Tvarious setup and function
aspects of multichannel speaker
configurations possible within
Dolby Digital Surround Sound
system playback. Basically, the
Speakers Menu controls deal with
distinct “one-time” settings for
such items as speaker volume
levels and sound delay (as related
to speaker distance and listening
room size dimensions).
ATSC
DTV Main Menu
Picture
Speaker Menu
Normal - Front in Line
Center Delay
Sound
Speakers
Features
Front
Left
Right
On/ Off
Left
On
Rear
DTV Setup
Right
Delay
Exit
3 feet/ 1 meter
Off
Test Tone
Subwoofer Level
Back
BEGIN
Center
Select the ATSC Speakers
Menu.
• Delay - control allows the user to adjust center
channel speaker sound for situations where external
Left/Right speakers are in use and their relative
distance/position from the DPTV’s internal cabinet
speakers may vary. (See pages 33 and 34 for further
details on front external speakers, amplifier surround
systems, and the use of the DPTV as a source for
center channel speaker sound.)
1
mute
With the DTV Main Menu on-
screen, move the highlight with the
MENU (M) ▲▼ buttons. Then
press the MENU button.
1
channel
TV
+
2
um
+
menu
-
Normal - Front in Line is for the speaker
arrangement where the center, left, and right
speakers are evenly lined up and roughly
equidistant from the user.
M
Press the Menu ᮤ or ᮣ arrow
buttons to adjust the selected
Speaker adjustment control.
2
exit
Analog
4/4
DTV
-
-
Center Forward setting compensates for a
center speaker being placed a few feet in front of
the external left and right speakers.
Center Back setting compensates for a center
speaker being placed a few feet behind the
position of the external left and right speakers.
1
2
3
Press the Menu (M) ▲▼ buttons
to move up and down the list of
individual Speaker Menu controls.
(See the Speaker Menu
information box to the right for
detailed descriptions on the select
controls.)
Front
• Left - control adjusts the volume level of the DPTV’s
left front internal cabinet speaker (or the Left Front
External Speakers Output terminal source on the rear
of the DPTV).
• Right - control adjusts the volume level of the
DPTV’s right front internal cabinet speaker (or the
Right Front External Speakers Output terminal
source on the rear of the DPTV).
3
Press the “exit” button to clear
the screen.
Rear
• On/Off - control allows the user to turn the rear
surround sound signals On or Off to the Surround
External Speaker Output terminals on the rear of the
DPTV.
STOP
• Left - control adjusts the volume level of the DPTV’s
left rear surround sound speaker (as connected
through the Left Surround External Speaker Output
terminal on the rear of the DPTV).
SMART HELP
• Right - control adjusts the volume level of the
DPTV’s right rear surround sound speaker
(as connected through the Right Surround External
Speaker Output terminal on the rear of the DPTV).
• Delay - control adjusts rear surround sound to
compensate for room size and how far the rear
surround speakers are located behind the system user
(3feet/1 meter; 6 feet/2 meters, etc.).
Note: Other speaker
configuration slide switch
controls are also located on the
rear of the DPTV. The FRONT
SPEAKERS and CENTER
CHANNEL INPUT switches
direct the use and audio signal
routing for the DPTV’s internal
cabinet speakers and external
output speaker terminals. (See
pages 33 and 34 for further details
on the location and use of these
additional audio speaker controls.)
Test Tone
• On/Off - allows the use of a test tone signal in order
to help set the volume levels for the individual
channel DPTV audio system speakers. (See the
following page for details on the use of the test tone
speaker adjustment process.)
Subwoofer Level
• Adjusts the volume level of a subwoofer speaker (as
connected through the Subwoofer Speaker Output
terminal on the rear of the DPTV).
Note: The DPTV’s additional Subwoofer Preamp
Output plug provides a variable line level signal
intended for an external “powered” subwoofer
capable of its own volume level adjustments.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL SPEAKERS MENU CONTROLS
E
xit
TEST TONE
he Test Tone Speaker Menu
Tcontrol generates a sound test
signal that can be used to adjust
individual DPTV speakers to
desired volume levels. The Test
Tone signal will be directed to each
audio speaker channel separately
(both internal DPTV cabinet
Speaker Menu
Normal - Front in Line
Center Delay
Front
Left
Right
On/ Off
Left
Speaker Menu
speakers and external Speaker
Output terminal connections) when
the control is turned On.
Rear
On
Normal - Front in Line
Center Delay
Front
Left
Right
Delay
Right
On/ Off
Left
3 feet/ 1 meter
On
On
Rear
Test Tone
Subwoofer Level
Right
Delay
BEGIN
Select Test Tone sound control.
3 feet/ 1 meter
On
Back
Test Tone
1
Subwoofer Level
Back
With the Speakers Menu on-screen,
move the highlight with the MENU
(M) ▲▼ buttons.
Speaker Menu
Center Delay
Normal - Front in Line
Front
Left
Right
On/ Off On
Left
Right
Delay
Press the MENU ᮤ ᮣ arrow
buttons to turn the Test Tone
control ON.
Rear
2
3
3
On
feet/
1
meter
mute
Test Tone
Subwoofer Level
Back
channel
UP
CH
TV
+
SOURCE
VOL
–
M
VO
+
L
EXIT
CH
DOWN
4
2
men
volume
With the Test Tone speaker
signal active, press the
+
M
MENU▲▼ arrow buttons to
select the desired DPTV system
speaker for individual volume level
adjustment (for example:
exit
Analog
4/4
DTV
1
3
5
Test Tone signal circulates through the speaker system
Front/Left, Rear/Right, etc.).
in a clockwise direction, and is meant to be used with the
adjustable Speaker Menu “barscale” controls (such as
Front Speaker Left/Right and Rear Speaker Left/Right).
Once turned On, the Test Tone will continue to circulate
through the Front and Rear speakers (even when other
sound controls are selected, such as Subwoofer, which
are not adjustable within the Test Tone mode.)
Press the MENU ᮤ ᮣ arrow
buttons on the Pronto remote, or
the Volume (+, -) buttons on the
DPTV’s local keyboard, to adjust
the selected speaker volume levels.
4
Continue and select the other
DPTV system speakers for
adjustment as desired.
Press the MENU▲▼ arrow
buttons to return to the Test Tone
Menu control when speaker
adjustments are complete and turn
the control Off.
5
STOP
37
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL FEATURES MENU CONTROLS
E
xit
CAPTIONS FORMAT
he Captions Format control is
Tused to set the DPTV to receive
the ATSC mode Closed Caption
(CC) feature. ATSC Closed
Caption presents the viewer with
program dialogue and
ATSC
conversations as written on-screen
“text box” windows.
DTV Main Menu
Picture
Sound
Speakers
Features
BEGIN
Select the ATSC Features
Menu.
1
Features Menu
DTV Setup
Captions Format
Captions On/ Off
Caption 1
Always On
Exit
With the DTV Main Menu on-
screen, move the highlight with the
MENU (M) ▲▼ buttons. Then
press the MENU button.
Add/ Delete Channel
Back
Note: The added resolution of active scan lines for
DTV (720p or 1080i) broadcasts, as opposed to analog
NTSC TV (525), can also provide for more defined
Closed Caption system character fonts and objects.
The ATSC display window for CC may be more on
the level of a computer with text windows containing a
variety of colors, size, and other object attributes.
2
3
Press the Menu ▲▼ arrow
buttons to select the Captions
Format control.
mute
1
channel
TV
+
3
m
+
menu
Press the Menu (M) ᮤ ᮣ
arrow buttons buttons to select
the desired Closed Caption format
mode. (Captions 1,2,3,4 and Text
1,2,3,4 modes are available for
selection.)
Note: As in the NTSC system not
all CC modes will currently be
active or available for all program
selections. Check your local
listings for CC program details.
M
exit
Analog
4/4
DTV
1
2
Features Menu
4
Captions Format
Captions On/ Off
Add/ Delete Channel
Caption 1
On during Mute
Back
Note: The “On during Mute” setting under the
Captions On/Off control can be used to set the DPTV
to turn the current selected Closed Caption mode
(example: Caption 1) "ON" whenever the MUTE
button on the remote is pressed.
4
Press the “exit” button to clear
the screen. The selected Closed
Caption mode will be active (with
the Captions On/Off control also
set to the “Always On” position.
To cancel, set the Captions On/Off
control to “Always Off.”
STOP
SMART HELP
Due to the increased data
capacity within the DTV
broadcast system (10 times the
capacity of the analog NTSC
system) the ATSC version of
Closed Caption will allow for
simultaneous transmission of
multiple languages and offer
various reading level options for
the captioned material (if
available).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV
M
a
in
M
e
n
u
P
ic
t
u
n
a
u
r
d
k
e
e
S
S
F
o
p
e
u
e
a
r
s
s
t
r
e
DTV
S
e
t
u
p
ATSC DIGITAL FEATURES MENU CONTROLS
E
xit
ADD/DELETE CHANNEL
he DTV Setup Menu control
T(see page 30) autoprograms all
available signal ATSC digital
channels into the DPTV’s scan
memory. Use the Add/Delete
Channel control to eliminate or
add to the specific list of “major”
channels contained within the
DPTV’s scan memory.
ATSC
DTV Main Menu
Picture
Sound
Speakers
Features
Note: Refer to page 5 in the
Features Menu
DTV Setup
64PP9901 Quick Use guide for
additional information on “major
and sub-channel” digital channel
selections and how they are used
within the ATSC broadcast system.
Captions Format
Captions On/ Off
Caption 1
Always On
Exit
Add/ Delete Channel
Back
BEGIN
Select the ATSC Features
Menu.
4
1
2
2
mute
3
1
With the DTV Main Menu on-
screen, move the highlight with the
MENU (M) ▲▼ buttons. Then
press the MENU button.
channel
TV
+
Add/ Delete Channel
menu
Add This Major Channel
Delete This Major Channel
volume
+
M
Back
exit
Press the Menu (M) ▲▼
buttons to select the Add/Delete
Channel control. Then press the
MENU button.
Analog
4/4
DTV
1
2
4
5
Press the CHANNEL (+)/(-)
(or number buttons on the Pronto’s
2/4 touchscreen display ) to select
the channel you want to add or
delete.
3
4
Press the MENU(M)
▲▼ buttons to select “Add this
Major Channel” control option,
and then press the Menu button to
add the specific digital channel
into the DPTV's scan memory.
OR
Press the MENU (M) ▲▼ buttons
to select “Delete this Major
Channel” and press the Menu
button to drop the digital channel
from the DPTV’s scan memory.
Repeat steps 2, 3 and 4 for each
channel you wish to add or delete.
5
Press the “exit” button to clear
the screen when complete.
STOP
39
Download from Www.Somanuals.com. All Manuals Search And Download.
PRONTO REMOTE ATSC DIGITAL FEATURES
PRONTO - DIGITAL TV MODE
status button
Press to see the current channel number on the DPTV screen.
Also press to clear the DPTV screen after control adjustments.
alternate audio*
Press to cycle through the available audio
he Pronto remote contains
Ttouchscreen displays for
“DTV” related controls. Use the
Pronto’s touchscreen buttons to
access and adjust the DPTV for
dedicated ATSC mode features, as
well as perform on-screen Menu
adjustments and select other
program functions.
language tracks for the current DTV program.
(See the additional alternate audio section
information shown below.)
dtv freeze
Press to freeze or stop the current picture on the DPTV screen.
Program sound will continue to play. Repress the freeze button, or
wait for a 60-second time out, to return to live program action.
power button
Press to turn the DPTV ON and OFF.
mute button
Press to turn the sound OFF on the DPTV. Press again to return
the sound to its previous level.
mute
Note: For battery installation and
other details on the initial use of
the Pronto remote control also
refer to the 64PP9901 Quick Use
guide included with your DPTV.
channel scan buttons
Press to scan up (+) or down (-) through any ATSC programmed
channel numbers.
channel
TV
+
power
alt audio
sleep
status
dtv freeze
ext input
volume
volume buttons
Press to adjust the DPTV sound level up (+) and down (-).
+
BEGIN
ext input button
analog TV
DTV
Press to select the auxiliary input connections available on
the rear of the DPTV (analog NTSC - AUX1/2/3; Monitor
-VGA; and External High Definition - EXT HD).
TV
1
Gently tap the Pronto
touchscreen with your finger to
display its control panel for use.
Analog
1/4
DTV
number buttons
Press two number buttons to select single digit “major”
DTV channels. Use a four-digit channel entry to select
ATSC system “sub-channel” programs, for example: press
“0, 6, 0, 1” for sub-channel 6.01. (See page 5 in the
64PP9901 Quick Use guide for details on the use and
Be sure “TV” is selected for the
current device tab item category.
Press the “DTV” button on
the Pronto to ensure ATSC mode
commands are sent from the
2
sleep button
Press to set the DPTV to
automatically turn itself OFF.
(15 minutes to 2 hours ahead.)
selection of sub-channels.)
A/CH
Analog
2/4
DTV
TV Guide Plus + buttons
TV
red
remote.
TV Guide Plus+ is not available for
use within the DPTV’s ATSC or
digital TV operating mode. (See the
separate TV Guide Plus+ program
instruction guide for details on how
it is used within the analog NTSC
operating system.)
STOP
A/CH button
Press Alternate Channel (A/CH) to select previously
viewed channels. Enter the desired two channel numbers
(from the Pronto remote’s number buttons), and then
press A/CH to toggle back and forth between the two
channel selections.
yellow
green
blue
on/off
info
setup
SMART HELP
record
Due to the amount of
optional component and
Analog
3/4
DTV
TV
menu
buttons
feature uses available with the
Pronto’s Device Reference and
Learn Code lists, please also refer
to the separate full-use Pronto
Owner’s Manual for complete
details on its function and
operations.
Press the Menu (or M) button to show on-screen
controls. Press M ▲ or ▼ buttons to move up (or
down) the list of DTV controls. Press the (M) ᮤ or
ᮣ buttons to make adjustments to the selected
controls.
menu
M
exit
exit button
Press to clear the DPTV screen after control
adjustments. Also press to see the current channel
number on the DPTV screen.
Analog
4/4
DTV
Alternate Audio preference: Englis h
* The “alt(ernate) audio” button on the Pronto
remote allows the user to select a language
preference for multilingual or alternate language
audio track programs that may be received for DTV
viewing. (English is the default language setting.)
scroll arrows
Press to move to the next (or previous) page of Pronto
controls. The touchscreen will display the current
control screen’s page number, and the total number of
pages available for the selected device (1/4; 2/4; etc.)
When digital broadcast material is received which
contains multiple language soundtracks the DPTV
will identify, find, and then select the preferred
alternate audio language for sound playback. If the
selected language preference is not available within
the received program material, the default audio
language is then selected.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
BRIGHTNES
S
P
S
S
I
CTURE
HARP
VM
N
ES
S
OFF
COLOR
TI
VOLUM
N
T
MONITOR FEATURES MENU CONTROLS
E
B
A
R
O
N
VGA/SVGA/HDCOMPONENT
nother function of the DPTV is
Afor the connection and use of
Personal Computers (PCs), and
other High Definition (HD) digital
source equipment, through the
DPTV’s Monitor inputs and
display mode. Dedicated Audio
Input jacks (located on the rear of
the DPTV) are also paired to the
external source Monitor Video
Inputs (VGA and HD Component
Video In) for audio playback
connections as well.
REAR OF DPTV
2
R
L
DIO OUT
STEREO IN
C
VGA
SVGA
EXT HD
6
CHANNEL
AUDIO IN
RS
LS
SW
1
Note: The DPTV will
display any Television
compatible VGA or
SVGA (60Hz only)
signal input.
VGA IN
INTERNAL TV SPEAKERS
USED AS CENTER
CHANNEL
FRONT
SPEAKERS
EX
INT
NO YES
75 ohm
HIGH
SYNC
PUT
H/H + V
V
–
+
MAX IN
–
+
50
W
FRONT EXTERNAL SPEAKERS OUT
–
–
+
+
R
L
R/Pr
G/Y
UP
CH
VOL
–
+
SOURCE
M
EXIT
VOL
SURROUND EXTERNAL SPEAKERS OUT
CH
DOWN
15 PIN VGA
Connection Cable
–
–+
+
For example: To connect a Philips
DVX8000 Multimedia Home
Theater (MMHT) for monitor
mode display use on the DPTV:
R
L
B/Pb
All External Speakers
8
ohms Min.
HD COMPONENT
VIDEO IN
Left/Right
Audio IN
BEGIN
mute
VIDEO
MULTI REMOTE
IN
AUDIO OUTPUT
SUB
WO
Connect a 15 pin VGA signal
cable (optional) from the VGA
(or SVGA) jack on the select
auxiliary equipment (example:
DVX8000 MMHT) to the VGA
Input jack on the DPTV.
1
L
FM
GND
AM
O
FE
R
TV
MONT
DSS
LD
VCR 2 IN-VCR-OUT
OUT
channel
ANTENNA
R
C
E
NTE
R
AC-3 RF
FRONT SURROUND
C
E
NTE
R
TV
status
+
AC-3/
PCM
COAX
L
AC-3/PCM
R
power
OPT
CD
IN-TAPE-OUT DSS
LD
VCR 2 IN-VCR-OUT MULTI
IN
IN
volume
TV
PHONE
T
V/C LE
A
B
alt audio
sleep
dtv freeze
ext input
+
A
N
T
RGB
SVGA
(RGB)
R DA
TA
LINE
ON
analog TV
DTV
MIC
IR
LINE IN
USB
OFF
1
2
3
Analog
1/4
DTV
REAR OF DVX8000 MMHT
Connect the Left/Right
STEREO IN jacks on the DPTV
to the (L/R) Audio Output jacks
(labeled Front) on the DVX8000
MMHT.
2
3
HD COMPONENT VIDEO IN
• 6 CHANNEL AUDIO IN(put) jacks paired to
HD Component Monitor Video Inputs (shown
below). For use with external accessory
equipment capable of Dolby Digital 5.1 level
audio output playback connections.
R
L
Press the “ext input” button
on the Pronto remote (or the
Source button on the DPTV’s local
keyboard) to select the required
Monitor mode. (VGA, SVGA, and
EXT HD Monitor modes are
SYSTEM AUDIO OUT
STEREO IN
C
6
CHANNEL
AUDIO IN
RS
LS
SW
• SYNC(hronization) slide switch used to set
the DPTV for digital HD Component signal
input source impedance (low-75 ohm or High).
VGA IN
INTERNAL TV SPEAKERS
USED AS CENTER
CHANNEL
FRONT
SPEAKERS
available for selection with the
“ext input” or Source buttons.)
EXT
INT
SUBWOOFER
PREAMP OUT
NO YES
75 ohm
HIGH
SYNC
• H/H + V (for combined Horizontal/Vertical
sync signals) or V(ertical) sync inputs control
the display of a RBG sourced picture in the left-
to-right dimension and from top-to-bottom.
CENTER
CHANNEL INPUT
SUBWOOFER
SPEAKER OUT
H/H + V
V
–
+
MAX IN
–
+
50
W
Use the DVX8000 MMHT as
the video (and/or audio) playback
source for material to be displayed
on the DPTV.
4
FRONT EXTERNAL SPEAKERS OUT
–
–+
+
R
L
R/Pr
G/Y
SURROUND EXTERNAL SPEAKERS OUT
• Separate Red/Green/Blue (Luminance-Y and
Color Difference-Pr/Pb) Component Video
Inputs provided for improved color bandwidth
information and highest possible picture
resolution for digital source connections. (See
BNC Connector information below.)
–
–+
+
R
L
B/Pb
All External Speakers
8
ohms Min.
HD COMPONENT
VIDEO IN
STOP
SMART HELP
• BNC (Bayonet Connectors) are available to
attach a computer to the DPTV for use as a
monitor display. The optional BNC cables
twist and secure to the individual
Red/Green/Blue and Horizontal/Vertical
Sync(hronization) component Video Inputs
on the rear of the DPTV. This type
connection ensures optimum video and color
reproduction performance from a computer,
or other external High Definition playback
source.
Note: The DPTV’s video
display may temporarily appear
misconverged during the initialization
of certain VGA input connected PC
programs (i.e., DOS). Once the PC
program has completed its “bootup”
phase, normal signal level processing
will reoccur and the DPTV display will
return to normal.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
BRIGHTNES
S
P
S
S
I
CTURE
HARP
VM
N
ES
S
OFF
COLOR
TI
VOLUM
N
T
E
B
A
R
O
N
MONITOR FEATURES MENU CONTROLS
MONITOR MENU CONTROLS
he Monitor Menu feature
Tcontrols are to aid you in
setting up the DPTV for the best in
display image quality. Generally,
the Monitor feature controls cover
the basics in color and video
image screen adjustments. A
variety of Monitor Audio Input
controls are also available for
various speaker trim adjustments
(dependent upon whether the
externally supplied Monitor input
source is capable of 2-channel
stereo or 6-channel digital sound
VGA
SVGA
EXT HD
BRIGHTNESS
PICTURE
SHARPNESS
COLOR
TINT
VOLUME BAR ON
(OR OFF)
- CHANNEL
(OR STEREO BACK)
BASS
AUDIO INPUT
6
TREBLE
BALANCE
TRIM LEFT
TRIM RIGHT
TRIM CENTER
TRIM SUBW FR
TRIM SURR L
TRIM SURR R
INTERNAL AMP
DISPLAY MODE
(OR OFF)
ON
VGA
(OR SVGA/ AUTO/ HD)
(OR 1 6 :9 FILL/ NORMAL)
(OR YUV/ RGB DIRECT)
(OR MODE 1 -8 )
replay).
DISPLAY FORMAT PC
BEGIN
INPUT TYPE
SYNC TYPE
HOR PHASE
BP W IDTH
ALIGN RED
ALIGN BLUE
RGB
AUTO
1
Press the “ext input” button
on the Pronto’s TV touchscreen, or
SOURCE on the local keyboard, to
place the DPTV in the desired
monitor display mode (VGA,
SVGA, EXTHD).
mute
channel
TV
+
1
power
alt audio
sleep
status
dtv freeze
ext input
v
• Use the Brightness and other
Monitor picture features (such as
Picture, Sharpness, etc.) to adjust
overall DPTV screen intensity for
optimum light/dark screen areas
and shading details.
• Turn the Volume Bar control
ON to display the volume level
settings for external audio sourced
material on the DPTV screen.
• Select the Bass/Treble/Balance
controls to adjust low/high fre-
quency sound and speaker
analog TV2
DTV
2
3
Press the MENU button to
display the Monitor Feature
Control Menu.
Analog
1/4
V
TV
4
menu
M
Press the (M) Up/Down ▲▼
Arrows on the Pronto’s
touchscreen display to highlight
items within the Monitor control
screen list.
exit
Analog
4/4
3
5
balance for external input audio
source material played through
the DPTV’s audio system.
• Use the Trim (Left, Right,
Center, Subwoofer, Surround
Left, Surround Right) controls
when adjusting sound for a 6-
channel audio input received
externally for playback through
the DPTV’s Monitor display
operating mode.
• Note: The list of Monitor Menu features (and
their individual control settings) will change
or readjust according to the capabilities of
the selected Display Mode (VGA, SVGA, etc.)
4
Press the Left/Right ᮤ ᮣ
Arrows on the Pronto to adjust the
selected on-screen feature control.
• Also, due to on-going DPTV product design
improvements such Monitor feature controls
as BP (Back Porch) Clamp are soon to be
automated for the sake of customer ease of use
and operation. These features will operationally
still be in place, but their functioning will be
transparent to the end user and will no longer
require any manual adjustments.
5
Press the “exit” button to clear
the screen when complete.
STOP
• Use the Display Mode, Format,
and Input controls to set the
DPTV for the type of external
monitor input source (VGA,
SVGA, EXT HD); the DPTV’s
display screen format used (PC,
Auto, 16:9); and RGB type signal
received.
SMART HELP
Certain barscale Monitor
Feature Menu adjustments
(such as Brightness, Picture, etc.)
will display separate control panel
screens for individual settings.
Repress the Menu button (on the
Pronto remote or local keyboard)
to return the DPTV to the Monitor
Menu when control adjustments
are complete.
• Additional Sync Type,
Horizontal Phase, Back Porch
(Clamp & Width), and
Alignment (Red & Blue)
controls can be used to adjust for
color shifts, black level, and
various other display screen
imagery.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
TIPS IF SOMETHING ISN'T WORKING
lease make these simple
Pchecks before calling for
service. These tips can save you
time and money since charges for
DPTV installation and
adjustment of customer controls
are not covered under your
warranty.
CAUTION: A video source (such as a video game, Compact Disc Interactive - CDI, or
TV information channel) which shows a constant non-moving pattern on the DPTV
screen, can cause picture tube damage. When your DPTV is continuously used with
such a source the pattern of the non-moving portion of the game (CDI, etc.) could leave
an image permanently on the picture tube. When not in use, turn the video source OFF.
Regularly alternate the use of such video sources with normal DPTV viewing.
• Check the DPTV power cord. Unplug the DPTV, wait 1 minute for the unit to reset,
then reinsert plug into outlet and push POWER button again.
• Check to be sure power outlet is not on a wall switch.
No Power
• Check for proper ATSC or NTSC antenna connections on the rear of the DPTV. Are
they properly secured to the appropriate antenna plug on the DPTV?
• For ATSC Autoprogram check DTV Setup for proper Full Installation option. Use
“Without Program and System Info” selection for initial digital station programming.
• Check the SOURCE, or “ext input” control on the remote, for the correct operating
mode for the DPTV (ATSC, NTSC, Auxiliary Inputs, Monitor, etc.).
No Picture or
Autoprogrammin
g Difficulties
• Check the CLOSED CAPTIONS control. Some TEXT modes could block the screen.
• Check the VOLUME and MUTE buttons on the DPTV and Pronto remote.
• Check the INTERNAL SPEAKERS CENTER CHANNEL INPUT switches (on rear of
DPTV) for proper position. Use the “NO” switch position for internal DPTV cabinet
speaker routing; and “YES” position when the DPTV speakers are intended as Center
Channel speakers within an external amplifier supplied Surround Sound system.
• If attempting auxiliary equipment hook-ups, check audio jack connections and ensure
auxiliary equipment is on and in the proper operating modes.
No Sound
• Check FRONT SPEAKERS switch (on rear of DPTV). Place in INT(ernal) position for
sound playback through the DPTV’s internal speaker system. EXT(ernal) for optional
external speaker playback connections using the Front and Surround Speakers Out(put)
terminals on the DPTV.
• Check for correct battery placement and position in Pronto remote battery compartment.
Replace with AA Heavy Duty (Zinc Chloride) or Alkaline batteries if necessary.
• Check the Device Tab button on the Pronto remote for correct selected device (“TV” to
operate the DPTV). Refer to the separate Pronto Remote Owner’s Manual for complete
details on its operation and use.
Remote Does
Not Work
• Press the Pronto’s “analog TV” or “DTV” touchscreen button to properly select and
send remote commands to the desired NTSC or ATSC DPTV mode of operation.
DPTV Displays
Wrong Channel or
incorrect program
• Check and be sure DPTV is in the proper operating mode (ATSC, NTSC, or Monitor).
• Repeat channel selection. In ATSC mode allow time for DTV channel acquistion and
display process to take place. For ATSC sub-channel selections be sure to enter the
desired four-digit channel number using the Pronto remote.
Note: The DPTV is equipped with protective circuitry that shuts the unit off in case of moderate power surges. Should this occur turn the DPTV
back on by pressing the POWER button once or twice, or unplug and then replug the power cord at the AC outlet. This feature is NOT designed to
prevent damage due to high power surges such as those caused by lightning, which is not covered by your warranty.
Cleaning and Care
• To avoid possible shock hazard be sure the DPTV is unplugged
from the electrical outlet before cleaning.
• Gently wipe the cabinet surfaces with a clean cloth or sponge
dampened in a solution of cool clear water and a mild soap or
detergent. Use a clean dry cloth to dry the wiped surfaces.
• Occasionally vacuum the ventilation holes or slots in the cabinet
back.
• Never use thinners, insecticide sprays, or other chemicals on or near
the cabinet, as they might cause permanent marring of the cabinet
finish.
• When cleaning the DPTV screen take care not to scratch or
damage the screen surface (avoid wearing jewelry or using
anything abrasive, do not use household cleaners). Wipe the front
screen with a clean cloth dampened with water. Use even, easy,
vertical strokes when cleaning.
• Specially designed screen cleaning kits are also available which
contain anti-static cleaners and cloths designed to get into the
ridges of the DPTV screen. If interested, ask your dealer or call
our toll-free Accessory Parts ordering number 1-800-292-6066.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Add/Delete Channels ..................6, 14-15, 29, 39, *Q/U-2, 5, 6
Audio Controls.........................19-22, 35-37, *Q/U-2, 4, 5, 6, 7
Audio/Video Inputs.........................24-26, 33-34, 41 *Q/U-2, 7
Automatic Programming ..................................6, 29, *Q/U-5, 6
Auxiliarty Inputs.............................24-26, 33-34, 41 *Q/U-2, 7
AVL (Automatic Volume Limiter).........................................22
Balance .......................................................................19, 35, 42
Bass.............................................................................19, 35, 42
Battery Installation .........................................................*Q/U-3
Cable TV Connections/Settings ...........................13, *Q/U-5, 6
Channel/Time Display..............................................17, *Q/U-6
Channel Memory.................................................13-14, *Q/U-2
Channel Label.........................................................................18
Cleaning and Care ....................................................43, *Q/U-3
Clearview..................................................................................8
Clock Setting ......................................................................6, 16
Closed Captioning ..........................................12, 38, *Q/U-5, 6
Color Controls ..............................................7, 30, *Q/U-5, 6, 7
Convergence.........................................................9, 31, *Q/U-5
Controls DPTV.......................................................*Q/U-2, 4, 6
Controls Remote.....................................23, 40, *Q/U-3, 4, 6, 7
Dolby Digital.....................................5, 33-34, 36, *Q/U-1, 2, 8
Exit .........................................................................*Q/U-2, 4, 6
Features.......................................................................5, *Q/U-1
First Time Set Up .............................................6, 29, *Q/U-5, 6
Glossary DPTV Terms ...........................................................45
Guide Plus+ IR Blaster...................................................*Q/U-2
High Definition Component Inputs.................41-42, *Q/U-2, 7
Inputs (Audio and Video) ................................24-26, 33-34, 41
Menu...................................................................*Q/U-2, 4, 6, 7
Menu Arrow Buttons.............................................*Q/U-4, 6, 7
Monitor Controls ..................................................42, *Q/U-2, 7
Programming Channels ........................................6, 29, *Q/U-2
Pronto Remote Control...........................23, 40, *Q/U-3, 4, 6, 7
Requesting Service............................................... 43, 46-47, 48
Safety/Precautions............................................2, 3, 44, *Q/U-1
Second Audio Program (SAP)................................................20
Sensor Remote................................................................*Q/U-2
Sleep Timer.......................................................................23, 40
Smart Picture.....................................................................10-11
SPDIF .......................................................................34, *Q/U-2
Speaker Switches ..........................................33-34, 36, *Q/U-2
Status Button.....................................................................23, 40
Surround Sound................................................32, 33-34, 36-37
SVGA..............................................................41-42, *Q/U-2, 7
System Audio Out ..............................................28, 34, *Q/U-2
Time/Channel Display..............................................17, *Q/U-2
VCR/DPTV Connections ..................................................24-27
Tips for Service ...........................................................43, 46-47
Treble..........................................................................19, 35, 42
VGA....................................................................41-42, *Q/U-7
Volume Display......................................................................21
Volume Limiter ................................................................22, 35
Warranty .................................................................................48
* Information contained in DPTV Quick-Use (Q/U) Guide - page listed
Regulatory Notices - Federal Communications Commission Notice
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. this
equipment generates, uses, and can radiate radio frequency energy
and , if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Modifications -
The FCC requires the user to be notified that nay changes or
modifications made to this device that are not expressly approved
by Philips Consumer Electronics may void the user’s authority to
operate the equipment.
Cables -
Connections to this device must be made with shielded cables with
metallic RFI/EMI connector hoods to maintain compliance with
FCC Rules and Regulations.
Canadian Notice -
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Avis Canadien -
Reorient or relocate the receiving antenna.
Cet appareil numérique de la classe B respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio or television technician
for help.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY TO TELEVISION TERMS
Audio/Video Inputs * Located on the rear of the DPTV these
Programming * The procedure of adding or deleting channel
numbers into the DPTV’s memory circuits. In this way the DPTV
“remembers’’ only the locally available or desired channel numbers and
skips over any unwanted channel numbers.
connectors (RCA phono type plug) are used for the input of audio and
video signals. Designed for use with VCRs (or other accessories) in
order to receive higher picture resolution and offer sound connection
options.
PSIP * Program and System Information Protocol.
Aspect Ratio * The proportions of a rectangular display screen. NTSC
television has a 4:3 ratio; HDTV is 16:9.
PTV * Projection Television (Rear and/or Front projection design
systems are available.)
ATSC * Advanced Television Systems Committee established by the
Federal Communications Commission to set standards for digital
television.
Remote Sensor Window * A window or opening found on the
DPTV control panel through which infrared remote control command
signals are received.
Coaxial Cable * A single solid antenna wire normally matched with a
metal plug (F-type) end connector that screws (or pushes) directly onto a
75 Ohm input found on the Television or VCR.
RF * Radio Frequency or modulated signal design used as the carrier
for television broadcasts.
Display * An on screen message or graphics that help the user operate
and adjust DPTV feature controls. See On Screen Displays (OSD).
RGB * Red, Green, Blue color component inputs used for connection
purposes with personal computers (PCs) and other high definition video
devices.
Dolby Digital * A digital 6-channel compression and surround sound
audio standard developed by Dolby Labs Inc. (also known as 5.1.)
Second Audio Program (SAP) * Another or additional audio
channel provided for in the Multichannel Television Sound (MTS)
broadcast standard. A monaural soundtrack included within the
recorded or video signal (usually containing a second language
translation for the displayed programming.)
DPTV * Digital Projection Television comprised of ATSC, NTSC, and
Monitor modules.
DTV * The broadly defined term used to describe the new digital
television system adopted by the Federal Communications Commission
(FCC) in December 1996.
SDTV * Standard Definition Television is a digital television
transmission, but with approximately the picture quality and aspect ratio
equivalent to NTSC video.
HDTV * High Definition Television which offers approximately twice
the vertical/horizontal resolution of NTSC video, and sound quality
approaching that of compact disc. (Usually taken to mean a picture of
1920 x 1080 pixels in a 16:9 aspect ratio.)
Status * Allows the user to quickly confirm what channel number is
currently being viewed. Status can also be used to clear the DPTV of on-
screen displays or information (rather than waiting for the displays to
“time out” or automatically disappear from the screen).
LED * Light Emitting Diode or indicator.
Subchannel * A complete digital channel number is composed of both
a major and minor (sub-) channel number. Located within the “major”
channel’s transmitted signal the “minor” channel can be used and
selected for additional programming.
Major Channel * The RF transmitted channel on which an ATSC
digital station is broadcast. (Also referred to as virtual channel.)
Menu * An on-screen listing of feature controls shown on the DPTV
screen that are made available for user adjustments.
Subwoofer * A speaker designed for audio playback of only the
lowest-frequency notes (under 100 Hz.)
MPEG * Motion Picture Experts Group and the video compression
formats devised for transmission of digital broadcasts.
SVGA * Super Video Graphics Array
Multichannel Television Sound (MTS) * The broadcast standard
that allows for stereo sound to be transmitted with the TV picture.
S-Video Input * Allows direct connection of high-resolution video
sources, such as a Super VHS videocassette recorder, Laser Disc player,
etc. Provides improved picture resolution, sharpness, and clarity.
NTSC * National Television Standards Committee format devised for
TV broadcasting signals in the 1940s (525 lines; 30Hz.)
Twin Lead Wire * The more commonly used name for the two strand
300 Ohm antenna wire used with many indoor and outdoor antenna
systems. In many cases this type of antenna wire requires an additional
adapter (or balun) in order to connect to the 75 Ohm Input terminals
designed into the more recent Televisions and VCRs.
On Screen Displays (OSD) * Refers to the wording or messages
generated by the DPTV to help the user with specific feature controls
(color adjustment, programming, etc.).
Variable Audio Output * An adjustable audio output which allows
for volume variations at the source.
Pre-Amplifier * The control center of a hi-fi system. Not only
amplifies source inputs, but also allows for source selection, volume,
tone, balance and all other controls that affect the sound.
VGA * Video Graphics Array
YUV * Component video signals consisting of Y luminance and
normalized color differences U and V.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Philips Consumer Electronics Company
Factory Service Center Locations
See Reverse Side for More Details.
Detroit/Toledo
•
Cleveland/
•
•
N Ohio •
•
Chicago
★ Columbus
•
San Francisco/Metro Area
★ Los Angeles
Charlotte
•
•
★ Pittsburgh/WV Area
Knoxville/E Tennessee
•
•
•
Philadelphia/S New Jersey
Atlanta/N Georgia
• Dallas
★ Wash/Balt
★ Orlando
•
Houston/Galveston
Beaumont/Austin
San Antonio
Tampa/W Florida
★ Ft. Myers/SW Florida
•
★ Indicates In-Home Service Only
1-800-242-9225
★ Miami/SE Florida
• Indicates In-Home/Carry-In Service
NOTE: If you reside in one of our Philips Factory Service Branch areas (see directory on back), you can contact the nearest Service Branch to
obtain efficient and expedient repair for your product. If your product is In-Warranty, you should have proof-of-purchase to ensure No Charge
Service. For Out-of-Warranty service, call the location nearest you.
NOTA: Si vous résidez dans une des régions desservies par une succursale de service après vente du fabricant Philips (voir liste ci-dessous), vous
pourrez contacter la branche de service après vente la plus près de chez vous pour obtenir un service après vente rapide et efficace. Si le produit
est sous garantie, il suffira de présenter une preuve d`achat pour bénéficier d'un service sans frais. Pour les produits non couverts par la garantie,
contactez le centre le plus près de chez vous.
NOTA: Si Ud. reside en una de nuestras zonas para sucursales Philips de servicio al de fábrica (ver directorio más abajo), Ud. puede comunicarse
con la sucursal de servicio más cercana para obtener una reparación oportuna y eficaz de su producto. Si su producto está todavía bajo garantía,
Ud. debe presentar comprobante de compra para no ocasionar ningunos cargos por servicio. Para servicio después del vencimiento de la
garantía, llame al lugar más cercano de los abajo indicados.
In Canada
How you can obtain efficient and expedient carry-in, mail-in, or in-home service for your product
Please contact Philips at
1-800-661-6162 (French speaking)
1-800-363-7278 (English speaking)
Au Canada
Comment obtenir le service après-vente pour les produits apportés ou envoyés par la poste à notre centre de service ou le service à domicile
Veuillez contacter philips á:
1-800-661-6162 (Francophone)
1-800-363-7278
En el Canadá
Cómo recibir servicio efficiente para su producto, en persona, por correo o a domicillo
Favor de comunicarse con Philips al:
1-800-661-6162 (francófono)
1-800-363-7278 (anglófono)
EL4482-3 Rev. Z
3135 015 07541
MAC2929 12/98
46
Download from Www.Somanuals.com. All Manuals Search And Download.
QUALITY SERVICE IS AS CLOSE AS YOUR TELEPHONE! SIMPLY LOOK OVER THE LIST BELOW FOR THE NUMBER OF A FACTORY SERVICE CENTER
NEAR YOU. YOUR PRODUCT WILL RECEIVE EFFICIENT AND EXPEDIENT CARRY-IN, MAIL-IN, OR IN-HOME SERVICE, AND YOU WILL RECEIVE PEACE OF MIND,
KNOWING YOUR PRODUCT IS BEING GIVEN THE EXPERT ATTENTION OF PHILIPS’ FACTORY SERVICE. AND, IF THE PHONE NUMBER LISTED FOR YOUR AREA
IS LONG DISTANCE, CALL 1-800-242-9225 FOR FACTORY SERVICE.
COMMENT OBTENIR NOTRE SERVICE APRÈS VENTE RAPIDE ET EFFICACE SOIT PAR COURRIER, À DOMICILE, OU EN SE PRÉSENTANT À UN CENTRE DE SERVICE PHILIPS. PLUS DE 600 CENTRES DE
RÉCEPTION DE PRODUITS À RÉPARER À TRAVERS LE PAYS: CONTACTER LE CENTRE DE SERVICE AUX CONSOMMATEURS LE PLUS PROCHE POUR SAVOIR L’EMPLACEMENT DE CES DÉPOTS DANS
UN RAYON DE 50 À 75 MILES (80 KM À 120 KM) DU CENTRE DE SERVICE LOCAL.
CÓMO OBTENER UN SERVICIO OPORTUNO Y EFICIENTE POR CORREO, EN CASA O EN PERSONA PARA SU PRODUCTO A TRAVÉS DE UN CENTRO PHILIPS DE SERVICIO. MAS DE 600 SITIOS POR
TODO EL PAIS PARA LA RECEPCION DE PRODUCTOS NECESITADOS DE REPARACIONES: COMUNICARSE CON EL CENTRO DE SERVICIO DE FABRICA MAS CERCANO PARA ESTOS LUGARES DENTRO
DE UN RADIO DE 80 A 120 KM (50 A 75 MILLAS) DEL CENTRO DE SERVICIO LOCAL.
GEORGIA
TEXAS
ILLINOIS
Philips Factory Service of Georgia
200 N. Cobb Pkwy., Suite 120
Marietta, GA 30062
Philips Factory Service of Texas
1110 N. Post Oak Rd., Suite 100
Houston, TX 77055
(713) 682-3990
Philips Factory Service of Illinois
1279 W. Hamilton Pkwy.
Itasca, IL 60143
(770) 795-0085
(630) 775-0990
FLORIDA
CENTRAL U.S.A.
TENNESSEE
Philips Factory Service of Florida
1911 US Highway 301 North
Tampa, FL 33619
Philips Factory Service Central US
950 Keynote Circle
Brooklyn Heights, OH 44131
(216) 741-3334
Philips Factory Service of East Tennessee
6700 D Papermill Rd.
Knoxville, TN 37919
(813) 621-8181
(423) 584-6614
WESTERN U.S.A.
MICHIGAN
MID-ATLANTIC
Philips Factory Service Western Region
681 East Brokaw Rd.
San Jose, CA 95112
Philips Factory Service of Michigan
25173 Dequindre
Madison Heights, MI 48071
(248) 544-2110
Philips Factory Service Mid-Atlantic
352 Dunks Ferry Rd.
Bensalem, PA 19020
(215) 638-7500
(408) 436-8566
DALLAS AREA
NORTH CAROLINA
Philips Factory Service of N. Carolina
520 G Clanton Rd.
Charlotte, NC 28217
(704) 529-6330
Philips Factory Service of Dallas
415 N. Main Street, #107
Euless, TX 76040
(713) 682-3990
MAC2929 12/98
47
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED W ARRANTY
DIGITAL PRO JECTIO N TELEVISIO N
One Year Free Labor
One Year Free Service on Parts
Two Years Free Service on Cathode Ray Tube Parts / 30 days Free Service on Projection TV Screen
This product can be repaired in-home.
W HO IS CO VERED?
MAKE SURE YO U KEEP...
You must have proof of purchase to receive warranty service. A sales
receipt or other document showing that you purchased the product is
considered proof of purchase.
Please keep your sales receipt or other document showing proof of
purchase. Attach it to this owner’s manual and keep both nearby. Also
keep the original box and packing material in case you need to return
your product.
W HAT IS CO VERED?
Warranty coverage begins the day you buy your product. for one year
thereafter (30 days for the digital projection TV screen), all parts will be
repaired or replaced, and labor and transportation are free. From one to
two years from the day of purchase, you pay for the replacement or
repair of all parts except the cathode ray tube and the “Clear-Vu” lens,
and for all labor and transportation charges. After two years from the day
of purchase, you pay for the replacement or repair of all parts except the
“Clear-Vu” lens (which is guaranteed against manufacturer’s defects for
the life of the product), and for all labor and transportation charges.
BEFO RE REQ UESTING SERVICE...
Please check your owner’s manual before requesting service.
Adjustments of the controls discussed there may save you a service
call.
TO GET W ARRANTY SERVICE...
Repair must be performed by an authorized service center or a factory
service center. If you do not live near a factory service center, contact your
dealer. If your dealer is an authorized service center, he will arrange
repair. If your dealer is not an authorized service center, he will direct
you to the authorized service center engaged by him to service the
products he sells.
All parts, including repaired and replaced parts, are covered only for
the original warranty period. When the warranty on the product
expires, the warranty on all replaced and repaired parts also expires.
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all implied warranties,
including implied warranties of merchantability and fitness for a
particular purpose, are limited in duration to the duration of this
express warranty. But, because some states do not allow limitations on
how long an implied warranty may last, this limitation may not apply to
you.)
W HAT IS EXCLUDED?
Your warranty does not cover:
•
labor charges for installation or setup of the product, adjustment of
customer controls on the product, and installation or repair of
antenna systems outside of the product.
(In Canada, this warranty is given in lieu of all other warranties. No
other warranties are expressed or implied, including any implied
warranties of merchantability or fitness for a particular purpose. Philips
is not liable under any circumstances for any direct, indirect, special,
incidental or consequential damages, howsoever incurred, even if
notified of the possibility of such damages.)
•
product repair and/or part replacement because of misuse,
accident, unauthorized repair or other cause not within the control
of Philips Consumer Electronics Company.
•
•
reception problems caused by signal conditions or cable or antenna
systems outside the unit.
a product that requires modification or adaptation to enable it to
operate in any country other than the country for which it was
designed, manufactured, approved and/or authorized, or repair of
products damaged by these modifications.
IF YO U HAVE Q UESTIO NS...
Please contact Philips at:
•
incidental or consequential damages resulting from the product.
(Some states do not allow the exclusion of incidental or
consequential damages, so the above exclusion may not apply to
you. This includes, but is not limited to, prerecorded material,
whether copyrighted or not copyrighted.)
1-800-661-6162 (French Speaking)
1-800-363-7278 (English Speaking)
REMEMBER...
Please record the model and serial numbers found on the product
below. Also, please fill out and mail your warranty registration card
promptly. It will be easier for us to notify you if necessary.
•
a product used for commercial or institutional purposes.
W HERE IS SERVICE AVAILABLE?
Warranty service is available in all countries where the product is
officially distributed by Philips Consumer Electronics Company. In
countries where Philips Consumer Electronics Company does not
distribute the product, the local Philips service organization will attempt
to provide service (although there may be a delay if the appropriate
spare parts and technical manual(s) are not readily available).
MODEL # ________________________________________________
SERIAL # ________________________________________________
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.
Philips Service Company, P.O. Box 2976, Longview, Texas 75606, (903) 242-4800
48
3135 015 12101
Download from Www.Somanuals.com. All Manuals Search And Download.
|