Register your product and get support at
DS9800W
User manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
ꢀꢁ 8SGDWHꢁÀUPZDUHꢁ
24
ꢁꢂ
ꢁꢂ
1 Important
Safety
4
4
5
'RZQORDGꢀWKHꢀXSGDWHꢀÀOHꢀ
8SGDWHꢀIURPꢀWKHꢀFRQÀJXUDWLRQꢀSDJHꢀ
Notice
8 Product information
26
ꢁꢃ
2 Your Entertainment System
Introduction
7
7
7
7
6SHFLÀFDWLRQVꢀ
What's in the box
What else you need
Overview of the wireless
SoundSphere speakers
Overview of the remote control
Overview of the docking charger
9 Troubleshooting
27
8
8
9
3 Prepare
10
10
11
Connect
Prepare the remote control
4 Connect to your homeWi-Fi
network for AirPlay
12
12
Scenario 1: Connect to a WPS router
Scenario 2: Connect to a non-WPS
router
13
19
5 Play
Stream audio from your iTunes music
library to DS9800W
Control play
Use advanced sound settings
Play from an external device
19
21
21
21
6 Charge your iPod/iPhone/iPad
through the separate docking
charger
22
22
22
Compatible iPod/iPhone/iPad
Load the iPod/iPhone/iPad
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
1 Important
d Follow all instructions.
e Do not use this product near water.
f Clean only with dry cloth.
Safety
Mains fuse
g Do not block any ventilation openings.
Install in accordance with the
This information applies only to products with a
UK mains plug.
manufacturer's instructions.
7KLVꢀSURGXFWꢀLVꢀÀWWHGꢀZLWKꢀDQꢀDSSURYHGꢀPROGHGꢀ
plug. If you replace the fuse, use one with:
‡ꢀ the ratings shown on the plug,
‡ꢀ a BS 1362 approval, and
‡ꢀ the ASTA approval mark.
Contact your dealer if you are not sure about
what type of fuse to use.
Caution:To conform with the EMC directive
(2004/108/EC), do not detach the plug from
the power cord.
h Do not remove the casing of this product.
i Only use this product indoors. Do
not expose the product to dripping /
splashing water, rain or high humidity.
j Keep this product away from direct
VXQOLJKWꢂꢁQDNHGꢁÁDPHVꢁRUꢁKHDWꢃ
k Do not install near any heat sources
such as radiators, heat registers, stoves,
or other electrical equipment (including
DPSOLÀHUVꢄꢃꢁ
Information for Europe:
Know these safety symbols
l Do not place any other electrical
equipment on the product.
m Do not place any sources of danger
on the product (e.g. objects containing
OLTXLGVꢂꢁEXUQLQJꢁFDQGOHVꢄꢃꢁ
n This product may include batteries. Please
refer to safety and disposal instructions
for batteries in this user manual.
o Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
The 'exclamation mark' calls attention to
features for which you should carefully read the
supplied literature to prevent operating and
maintenance problems.
The 'lightening bolt' symbol indicates
uninsulated components within the product
that can cause an electric @shock.
7RꢀUHGXFHꢀWKHꢀULVNꢀRIꢀÀUHꢀRUꢀHOHFWULFꢀVKRFNꢄꢀGRꢀ
not expose the product to rain or moisture and
GRꢀQRWꢀSODFHꢀDQ\ꢀREMHFWVꢀÀOOHGꢀZLWKꢀOLTXLGVꢄꢀVXFKꢀ
as vases, on the product.
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning
‡ Never remove the casing of this apparatus.
‡ Never lubricate any part of this apparatus.
‡ Never place this apparatus on other electrical
HTXLSPHQWꢅ
‡ Keep this apparatus away from direct sunlight, naked
ÁDPHVꢀRUꢀKHDWꢅꢀ
The device can be operated in the EU without
restrictions indoor, but cannot be operated
outdoors in France in the whole of the band
until further notice.
‡ Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
7KLVꢀSURGXFWꢀFRPSOLHVꢀZLWKꢀWKHꢀUHTXLUHPHQWꢀRIꢀ
the 1999/5/EC directive.
Risk of overheating! Never install this apparatus
LQꢀDꢀFRQÀQHGꢀVSDFHꢅꢀ$OZD\VꢀOHDYHꢀDꢀVSDFHꢀRIꢀ
at least four inches around this apparatus for
ventilation. Ensure curtains or other objects
never cover the ventilation slots on this
apparatus.
0RGLÀFDWLRQV
0RGLÀFDWLRQVꢀQRWꢀDXWKRUL]HGꢀE\ꢀWKHꢀ
manufacturer may void user's authority to
operate this product.
Mains fuse
This information applies only to products with a
UK mains plug.
7KLVꢀSURGXFWꢀLVꢀÀWWHGꢀZLWKꢀDQꢀDSSURYHGꢀPROGHGꢀ
plug. If you replace the fuse, use one with:
‡ꢀ the ratings shown on the plug,
‡ꢀ a BS 1362 approval, and
Your product is designed and manufactured
ZLWKꢀKLJKꢀTXDOLW\ꢀPDWHULDOVꢀDQGꢀFRPSRQHQWVꢄꢀ
which can be recycled and reused.
‡ꢀ the ASTA approval mark.
Contact your dealer if you are not sure about
what type of fuse to use.
Caution:To conform with the EMC directive
(2004/108/EC), do not detach the plug from
the power cord.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
QHJDWLYHꢀFRQVHTXHQFHVꢀIRUꢀWKHꢀHQYLURQPHQWꢀDQGꢀ
human health.
Notice
This product complies with the radio
LQWHUIHUHQFHꢀUHTXLUHPHQWVꢀRIꢀWKHꢀ(XURSHDQꢀ
Community.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
“Made for iPod,”“Made for iPhone,” and “Made
for iPad” mean that an electronic accessory
KDVꢀEHHQꢀGHVLJQHGꢀWRꢀFRQQHFWꢀVSHFLÀFDOO\ꢀWRꢀ
iPod, iPhone, or iPad, respectively, and has
EHHQꢀFHUWLÀHGꢀE\ꢀWKHꢀGHYHORSHUꢀWRꢀPHHWꢀ
Apple performance standards.Apple is not
responsible for the operation of this device
or its compliance with safety and regulatory
standards. Please note that the use of this
accessory with iPod, iPhone, or iPad may affect
wireless performance.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
QHJDWLYHꢀFRQVHTXHQFHVꢀIRUꢀWKHꢀHQYLURQPHQWDOꢀ
and human health.
AirPlay, iPod, and iPhone are trademarks of
Apple Inc., registered in the U.S. and other
countries. iPad is a trademark of Apple Inc.
Information about the use of batteries:
Caution
Class II equipment symbol:
‡ 5LVNꢀRIꢀOHDNDJHꢆꢀ2QO\ꢀXVHꢀWKHꢀVSHFLÀHGꢀW\SHꢀRIꢀEDWWHULHVꢅꢀ
Do not mix new and used batteries. Do not mix
different brands of batteries. Observe correct polarity.
Remove batteries from products that are not in use for
a longer period of time. Store batteries in a dry place.
‡ Risk of injury:Wear gloves when handling leaking
batteries. Keep batteries out of reach of children and
pets.
‡ Risk of explosion: Do not short circuit batteries. Do
not expose batteries to excessive heat. Do not throw
EDWWHULHVꢀLQWRꢀWKHꢀÀUHꢅꢀ'RꢀQRWꢀGDPDJHꢀRUꢀGLVDVVHPEOHꢀ
batteries. Do not recharge non-rechargeable batteries.
CLASS II apparatus with double insulation, and
no protective earth provided.
Note
‡ The type plate is located on the bottom of the
apparatus.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
DꢀVSHFLDOL]HGꢀFRPSDQ\ꢅꢀ3OHDVHꢀREVHUYHꢀWKHꢀ
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
HTXLSPHQWꢅ
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
With DS9800W, you can also:
2 Your
‡ꢀ play music from other audio devices
through the MP3-LINK socket.
Entertainment
With the supplied separate docking charger,
you can:
System
‡ꢀ charge your iPod/iPhone/iPad directly.
Congratulations on your purchase, and
ZHOFRPHꢀWRꢀ3KLOLSVꢇꢀ7RꢀIXOO\ꢀEHQHÀWꢀIURPꢀWKHꢀ
support that Philips offers, register your product
If you contact Philips, you will be asked for the
model and serial number of this apparatus.The
model number and serial number are on the
bottom of the apparatus.Write the numbers
here:
What's in the box
Check and identify the contents of your package:
‡ꢀ Main unit (2 x wireless SoundSphere
speakers, with a built-in Wi-Fi module)
‡ꢀ 1 x speaker connection cable
‡ꢀ 1 x AC power cord (for the main unit)
‡ꢀ 1 x remote control with battery (for
the main unit)
Model No. __________________________
Serial No. ___________________________
‡ꢀ 1 x MP3 link cable
‡ꢀ 1 x separate docking charger
‡ꢀ 1 x AC power adaptor (for the docking
charger)
‡ꢀ User manual (in CD-ROM)
‡ꢀ Quick start guide
Introduction
Apple AirPlay technology enables you to play
your iTunes music library, hosted on a Mac, PC,
iPhone, iPod touch, or iPad on any AirPlay-
enabled device (for example, your DS9800W)
connected to the Wi-Fi network.
With an AirPlay-enabled device (for example,
your DS9800W), you can:
What else you need
To stream audio wirelessly by AirPlay, you need:
‡ꢀ $ꢀ:Lꢈ)LꢀFHUWLÀHGꢀURXWHU
‡ꢀ stream audio from your iTunes music
library to any room in your house
‡ꢀ choose which AirPlay-enabled devices
you want to play music on (if you have
more than one such devices in your
house)
‡ꢀ stream audio to multiple AirPlay-
enabled devices at the same time
(from the iTunes music library on your
PC/Mac only)
‡ꢀ A host for your iTunes music library,
for example, an iPod touch/iPhone/
iPad installed with iOS 4.3 (or later) or
a Wi-Fi enabled PC/Mac installed with
iTunes 10 (or later)
Your DS9800W should be connected to the
same local network as your iTunes host device
through the Wi-Fi router.
Tip
about more Philips AirPlay-enabled devices.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
a
List of compatible iTunes host devices
for AirPlay
‡ꢀ Turn the unit on/off.
‡ꢀ (Press and hold) reset the unit.
In terms of AirPlay, DS9800W is compatible
with:
b MP3-LINK
‡ꢀ Connect an external audio player
through the supplied MP3 link cable.
‡ꢀ a Wi-Fi enabled PC/Mac installed with
iTunes 10 (or later); and
‡ꢀ the following iPod/iPhone/iPad models
installed with iOS 4.3 (or later):
‡ꢀ iPad 2
c ~ AC IN
‡ꢀ Connect the power cord.
d 6SHDNHUꢁFRQQHFWRUVꢁꢅꢆꢇꢈꢄ
‡ꢀ Connect the two speakers through the
supplied speaker cable.
‡ꢀ iPad
‡ꢀ iPhone 4
‡ꢀ iPhone 3GS
‡ꢀ iPod touch (2nd, 3rd, and 4th
generation)
e WiFi SETUP
‡ꢀ Connect the unit to a Wi-Fi network.
f LED indicator
‡ꢀ Show the current status of the unit.
Overview of the wireless
SoundSphere speakers
g IR sensor
‡ꢀ Detect signals from the remote
control. Point the remote control
directly at the sensor.
f
a
e
b
d
c
g
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview of the remote
control
Overview of the docking
charger
a
b
a
b
g
c
f
e
c
d
a ~ DC IN
‡ꢀ Connect the power adaptor.
b ON/OFF
‡ꢀ Switch on or off the LED light around
the docking charger.
a
‡ꢀ Turn the unit on/off.
c iPod/iPhone/iPad dock connector
b
‡ꢀ Select the AirPlay device audio source.
c +/-
‡ꢀ Adjust volume.
d
e
f
g
‡ꢀ Mute or restore volume.
/
‡ꢀ Skip to the previous/next track.
‡ꢀ Start or pause play.
‡ꢀ Select the MP3 link audio source.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Screw the left black (-) connector to
3 Prepare
secure the cable.
6 Repeat steps 2-5 to insert the other
speaker cable into the right connectors.
Always follow the instructions in this chapter in
VHTXHQFHꢅ
Connect power
Caution
Connect
‡ Risk of product damage! Make sure that the power
supply voltage matches the voltage printed on the
bottom of the unit.
‡ Risk of electric shock! When you unplug the AC cord,
always pull the plug from the socket. Never pull the
cord.
‡ Before you connect the AC cord, make sure that you
have completed all the other connections.
Connect speaker cables
Note
‡ Insert the stripped portion of each speaker wire into
the socket completely.
‡ For optimal sound, use the supplied speakers only.
1
2
3
‡ꢀ Connect the AC power cord to
‡ꢀ the ~ AC IN socket on the back of the
main speaker.
1 Unscrew the speaker connectors.
2 Insert fully the end of a speaker cable with
‡ꢀ the wall power socket.
red mark into the left red (+) connector.
3 Screw the left red (+) connector to secure
the cable.
4 Insert fully the end of a speaker cable
without red mark into the left black (-)
connector.
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
To replace the remote control battery:
Turn DS9800W on
After proper power connection, the unit
switches on automatically.
‡ꢀ Wait for successful boot-up of the unit.
» The boot-up takes about 35 seconds.
» During boot-up, the LED indicator
on the back of the unit blinks green
TXLFNO\ꢅꢀ
» After boot-up, if no Wi-Fi connection
has been set up for DS9800W, the
LED indicator starts to blink green
slowly.
‡ꢀ To switch the unit to standby mode,
1 Open the battery compartment.
press
.
‡ꢀ To switch the unit on from standby mode,
2 Insert one CR2032 battery with correct
press again.
polarity (+/-) as indicated.
3 Close the battery compartment.
Prepare the remote control
Note
Caution
‡ Before you press any function button on the remote
FRQWUROꢄꢀÀUVWꢀVHOHFWꢀWKHꢀFRUUHFWꢀVRXUFHꢀZLWKꢀWKHꢀUHPRWHꢀ
control instead of the main unit.
‡ If you are not going to use the remote control for a
long time, remove the battery.
‡ Risk of explosion! Keep batteries away from heat,
VXQVKLQHꢀRUꢀÀUHꢅꢀ1HYHUꢀGLVFDUGꢀEDWWHULHVꢀLQꢀÀUHꢅ
‡ Point the remote control directly at the IR sensor on
the front of the main speaker for better reception.
)RUꢁÀUVWꢈWLPHꢁXVHꢉꢁ
1 Remove the protective tab to activate the
remote control battery.
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Make sure that your Wi-Fi router is
4 Connect to
your homeWi-
Fi network for
AirPlay
powered on and working properly.
2 Make sure that DS9800W has been
powered on and booted up successfully
(see 'Turn DS9800W on' on page 11).
3 Identify the type of your Wi-Fi router (see
the user manual of your Wi-Fi router for
details).
Scenario 1: Connect to a
WPS router
Note
‡ Before you press any button on DS9800W, make sure
that DS9800W has been booted up successfully (see
'Turn DS9800W on' on page 11).
1 Press the WPS button on your home Wi-Fi
router.
WPS
To connect DS9800W to your existing home
Wi-Fi network, you need to apply your home
Wi-Fi setting to DS9800W.
You can do this in two ways (depending on
which type of Wi-Fi router you use):
‡ꢀ Automatically - if your Wi-Fi router is
WPS (Wi-Fi Protected Setup)-enabled
and supports PBC (Push Button
Connection) (see 'Scenario 1: Connect
to a WPS router' on page 12)
‡ꢀ Manually - if your Wi-Fi router does
not support WPS (see 'Scenario 2:
Connect to a non-WPS router' on
page 13)
2 Shortly after step 1, press Wi-Fi SETUP on
the back of the main speaker.
» The LED indicator blinks red, yellow
and green alternately.
Once connected successfully, DS9800W will
remember your home Wi-Fi settings.Then
you can enjoy AirPlay whenever DS9800W is
powered on and connected to your home Wi-
Fi network automatically.
» Within 2 minutes, the LED indicator
stops blinking and stays green, and the
unit beeps.
» DS9800W is connected to your home
Before connection of DS9800W to you home
Wi-Fi network, check the points below.
Wi-Fi network successfully.
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
The Wi-Fi enabled device can be an iPod touch/
iPhone/iPad or a Wi-Fi enabled PC/Mac.
)ROORZꢀWKHꢀVHTXHQFHꢀEHORZꢀIRUꢀFRQQHFWLRQꢀRIꢀ
DS9800W to a non-WPS Wi-Fi router.
1 Collect settings of your home Wi-Fi router
and write down on paper for use during
DS9800W Wi-Fi setup (see 'Collect
settings of your home Wi-Fi router' on
page 14).
WIFI
SETUP
2 Switch DS9800W to Assisted Wi-Fi Setup
mode (see 'Switch DS9800W to Assisted
Wi-Fi Setup mode' on page 14).
» A new Wi-Fi network created by
DS9800W will appear, with the
network name (SSID) of Philips Fidelio
AirPlay.
3 Connect your Wi-Fi enabled device to the
created new Wi-Fi network temporarily
(see 'Connect your Wi-Fi enabled device
to the newly created Wi-Fi network' on
page 14).
Tip
‡ For some Wi-Fi routers, you may need to hold the
WPS button for Wi-Fi connection or enable the WPS
3%&ꢀIXQFWLRQꢀIURPꢀWKHꢀURXWHUꢀFRQÀJXUDWLRQꢀSDJHVꢅꢀ6HHꢀ
WKHꢀXVHUꢀPDQXDOVꢀRIꢀWKHꢀVSHFLÀFꢀURXWHUVꢀIRUꢀGHWDLOVꢅ
‡ If the LED indicator on DS9800W blinks yellow, it
means that the Wi-Fi connection has failed. Please wait
for 2 minutes and try again. If the problem remains, try
to set up the Wi-Fi connection manually (see 'Scenario
2: Connect to a non-WPS router' on page 13).
4 Open the built-in web page of DS9800W
with the Internet Browser of your Wi-Fi
enabled device (see 'Open the built-in web
page of DS9800W' on page 16).
‡ If the Wi-Fi connection fails again, press and hold
the main speaker to reset it, and then try again.
on
5 Change the internal Wi-Fi settings of
DS9800W based on the settings you
wrote on paper at step 1 (see 'Change the
internal Wi-Fi settings of DS9800W' on
page 17).
Scenario 2: Connect to a
non-WPS router
6 Restore your Wi-Fi enabled device back
to your existing home Wi-Fi settings (see
'Restore your Wi-Fi enabled device back
to your existing home Wi-Fi setting' on
page 18).
Note
‡ You can also follow the procedures below to connect
DS9800W to a WPS router manually.
To connect DS9800W to a Wi-Fi router
manually, you need access to DS9800W's
EXLOWꢈLQꢀFRQÀJXUDWLRQꢀZHEꢀSDJHꢀIRUꢀFKDQJHꢀRIꢀ
its internal Wi-Fi settings.To do so, you need a
Wi-Fi enabled device with an Internet browser
for temporary Wi-Fi connection to DS9800W.
EN 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Collect settings of your homeWi-Fi
router
Note
‡ $IWHUꢀ\RXꢀÀQLVKꢀPDQXDOꢀ:Lꢈ)LꢀVHWWLQJꢀIRUꢀ'6ꢉꢊꢋꢋ:ꢄꢀWKLVꢀ
new Wi-Fi network disappears.
‡ If you fail to enter Assisted Wi-Fi Setup mode, power
off DS9800W and power on it, then try again after
successful boot-up.
‡ Make sure that there are no other Philips AirPlay-
enabled devices in Assisted Wi-Fi Setup mode at the
same time. Multiple new Wi-Fi networks created this
way may interfere with each other.
Note
‡ Always consult the user manual of your home Wi-Fi
router for detailed instructions.
1 Connect your Wi-Fi enabled device to
your existing home Wi-Fi network.
2 Launch the Internet browser (for example,
Apple Safari or Microsoft Internet
Connect yourWi-Fi enabled device to
the newly createdWi-Fi network
Explorer) on your Wi-Fi enabled device.
3
2SHQꢀWKHꢀFRQÀJXUDWLRQꢀSDJHꢀRIꢀ\RXUꢀ
home Wi-Fi router.
The newWi-Fi network created by DS9800W
only allows access of oneWi-Fi enabled device.To
avoid interference from any otherWi-Fi devices,
you are recommended to temporarily disable the
Wi-Fi function on your otherWi-Fi devices.
4 Find the Wi-Fi settings tab and write down
the following information on paper:
A Network name (SSID)
B Wi-Fi security mode (usually WEP,
WPA or WPA2 if enabled)
Option 1: Use your iPod touch/iPhone/iPad
C Wi-Fi password (if Wi-Fi security is
1 Select Settings -> Wi-Fi on your iPod
enabled)
touch/iPhone/iPad.
D DHCP mode (enabled or disabled)
E Static IP address settings (if DHCP
mode is disabled)
Switch DS9800W to AssistedWi-Fi
Setup mode
‡ꢀ After successful boot-up (see 'Turn
DS9800W on' on page 11), press and hold
Wi-Fi SETUP on the back of the main
speaker for more than 5 seconds.
» The LED indicator blinks green and
yellow alternately.
» A new Wi-Fi network of DS9800W
itself is created, with the network name
(SSID) of Philips Fidelio AirPlay.
» It takes about 45 seconds for successful
creation of this new Wi-Fi network.
14 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Select Philips Fidelio AirPlay from the list
2 Scan the available Wi-Fi networks.
of available networks.
Philips Fidelio AirPlay
3 Select Philips Fidelio AirPlay from the list
of available networks.
3 Wait until successful Wi-Fi connection on
your iPod touch/iPhone/iPad.
»
is displayed at the upper left
corner of your iPod touch/iPhone/iPad.
Tip
4 Wait until successful Wi-Fi connection on
‡ If Philips Fidelio AirPlay is not in the list, try to scan the
available Wi-Fi networks again.
your PC/Mac.
Option 2: Use yourWi-Fi enabled PC/Mac
Note
‡ See the user manual of your PC/Mac for how to
connect your PC/Mac to a Wi-Fi network.
‡ During Wi-Fi network connection, do not connect any
network cable to your PC/Mac.
1 Open the Wi-Fi setup tool or control
panel on your PC/Mac.
EN 15
Download from Www.Somanuals.com. All Manuals Search And Download.
If you use Safari on yourWi-Fi enabled PC/
Mac, you can also select 'Philips_Fidelio XXX'
from the Bonjour pull-down list to enter the
'6ꢊꢋꢌꢌ:ꢁFRQÀJXUDWLRQꢁZHEꢁSDJHꢁGLUHFWO\ꢃ
Tip
‡ If Philips Fidelio AirPlay is not in the list, try to scan the
available Wi-Fi networks again.
1 Click -> Preferences.
» The Bookmarks menu is displayed.
Open the built-in web page of
DS9800W
1 Launch Apple Safari browser or any other
Internet browser on your Wi-Fi enabled
device.
2 Type in 192.168.1.1 at the browser
DGGUHVVꢀEDUꢀDQGꢀFRQÀUPꢅ
» 7KHꢀ'6ꢉꢊꢋꢋ:ꢀFRQÀJXUDWLRQꢀZHEꢀ
page is displayed.
2 Tick Include Bonjour for Bookmarks bar.
192.168.1.1
3 Select 'Philips_Fidelio XXX' from the
Bonjour pull-down list shown at the
bookmarks bar.
» 7KHꢀ'6ꢉꢊꢋꢋ:ꢀFRQÀJXUDWLRQꢀZHEꢀ
page is displayed.
16 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Change the internalWi-Fi settings of
DS9800W
Note
‡ If the LED indicator on DS9800W does not stay
green steadily, it means that the Wi-Fi connection has
failed. Please power off both your Wi-Fi router and
DS9800W and then power on them again to see
whether DS9800W can be connected to your home
Wi-Fi network. If the problem remains, try the above
procedures again.
2QꢀWKHꢀ'6ꢉꢊꢋꢋ:ꢀFRQÀJXUDWLRQꢀZHEꢀSDJHꢄꢀ
you can change the internal Wi-Fi settings of
DS9800W for connection of DS9800W to
your existing home Wi-Fi network.
‡ $IWHUꢀ\RXꢀÀQLVKꢀWKHꢀDERYHꢀFKDQJHVꢀRUꢀSRZHUꢈRIIꢀDQGꢀ
power-on of DS9800W, the new Wi-Fi network
created by DS9800W will disappear.
Note
‡ 0DNHꢀVXUHꢀWKDWꢀWKHꢀVHWWLQJVꢀRQꢀWKHꢀFRQÀJXUDWLRQꢀZHEꢀ
page match your home Wi-Fi network settings that you
wrote on paper.
Tip
‡ If you like, you can change the name of your DS9800W
in Advanced settings -> AirPlay Device Name on the
'6ꢉꢊꢋꢋ:ꢀFRQÀJXUDWLRQꢀZHEꢀSDJHꢅꢀ7KLVꢀLVꢀKHOSIXOꢀZKHQꢀ
you have multiple Philips AirPlay-enabled devices in
your house and you need to distinguish between them.
‡ If you want to enter the network name (SSID) manually
(for example, if you want to hide your SSID), go to
Advanced settings -> CONFIGURE MANUALLY on
WKHꢀ'6ꢉꢊꢋꢋ:ꢀFRQÀJXUDWLRQꢀZHEꢀSDJHꢅ
‡ꢀ Follow the on-screen instructions to
FKDQJHꢀDQGꢀFRQÀUPꢀWKHꢀLQWHUQDOꢀ:Lꢈ)Lꢀ
settings of DS9800W.
» After a while, the indicator on the back
of DS9800W stops blinking and stays
green, and the unit beeps.
» DS9800W is connected to your
existing home Wi-Fi network
successfully.
EN 17
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Select your network name (SSID) from the
Restore yourWi-Fi enabled device
back to your existing homeWi-Fi
setting
list of available wireless networks.
Note
‡ Make sure that the settings at steps 2 to 3 below match
your home Wi-Fi network settings you wrote on paper.
1 Select Settings ->Wi-Fi on your iPod
touch/iPhone/iPad.
‡ꢀ Or open the list of available Wi-Fi
networks on your PC/Mac.
3
(QWHUꢀWKHꢀQHWZRUNꢀNH\ꢀLIꢀUHTXLUHGꢅ
4 Wait until successful Wi-Fi connection to
your home Wi-Fi network.
18 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Select Philips_Fidelio XXXX (or user
5 Play
FXVWRPL]HGꢀQDPHꢌꢀIURPꢀWKHꢀ$LU3OD\ꢀOLVWꢅ
Stream audio from your
iTunes music library to
DS9800W
Note
‡ Make sure that your iTunes host device is connected
to the same Wi-Fi network as DS9800W.Your iTunes
device can be an iPod touch/iPhone/iPad installed with
iOS 4.3 (or later) or a Wi-Fi enabled PC/Mac installed
with iTunes 10 (or later).
Stream from your iPod touch/iPhone/
iPad
1 Launch the iPod/Music application on your
iPod touch/iPhone/iPad.
2 Tap on the AirPlay icon.
EN 19
Download from Www.Somanuals.com. All Manuals Search And Download.
4
6HOHFWꢀDꢀPHGLDꢀÀOHꢀDQGꢀVWDUWꢀSOD\ꢅ
» After a while, you will hear music from
DS9800W.
Stream from your PC/Mac
1 Launch iTunes 10 (or a later version) on
your PC/Mac.
2 Click the AirPlay icon on the window.
3 Select Philips_Fidelio_AirPlay XXXX (or
XVHUꢀFXVWRPL]HGꢀQDPHꢌꢀIURPꢀWKHꢀ$LU3OD\ꢀ
list.
Note
‡ If you fail to hear music after successful setup, do one of
the following on your iPod touch/iPhone/iPad:
‡ (1) Disconnect and then re-connect to the same Wi-Fi
router again;
‡ (2) Close all applications running at the background;
‡ (3) Power off and then power on your iPod touch/
iPhone/iPad again.
4
6HOHFWꢀDꢀPHGLDꢀÀOHꢀDQGꢀVWDUWꢀSOD\ꢅ
» After a while, you will hear music from
DS9800W.
20 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
If your iTunes host device is aWi-Fi enabled
PC/Mac:
For advanced sound settings, you can use the
HTXDOL]HUꢀDYDLODEOHꢀRQꢀL7XQHVꢀGLUHFWO\ꢀꢍView ->
Show Equalizer).
Tip
‡ When you stream audio from your iTunes music library
on a PC/Mac, you can select more than one AirPlay-
enabled devices (if available) at step 3 to stream music
to all of them at the same time.
‡ If you are using an earlier version of iTunes, the AirPlay
icon may be instead of
.
Tip
‡ See the iTunes help documentation for more details.
Control play
You can select different play options from either
your iTunes host device or DS9800W.
Play from an external device
You can also listen to an external audio player
through DS9800W.
Note
‡ The operations below are based on the supplied
remote control of DS9800W.
‡ Make sure that you have successfully streamed audio
from your iTunes music library to DS9800W.
‡ꢀ To start or pause play, press
.
‡ꢀ To skip to the previous or next track, press
/
.
‡ꢀ To adjust volume, press +/- repeatedly.
‡ꢀ To mute or restore volume, press
‡ꢀ To switch to the MP3 link audio source (if
connected), press
‡ꢀ To switch back to the AirPlay audio source,
.
.
MP3-LINK
press
.
Tip
‡ If you are streaming music from a PC/Mac, to control
music play from AD7000W, launch iTunes and tick
Allow iTunes audio control from remote speakers
in Edit (for Windows) or iTunes (for Mac) ->
Preferences... -> Devices.
1 Connect the supplied MP3 link cable to:
‡ꢀ the MP3-LINK socket on the back of
DS9800W.
‡ꢀ the headphone socket on an external
audio player.
2 Press
to select the MP3 link source.
Use advanced sound settings
If your iTunes host device is an iPod touch/
iPhone/iPad:
For advanced sound settings and additional
features, you can use your iPod touch/iPhone/
iPad to download the Philips Fidelio application
from Apple App Store. It is a free application
from Philips.
EN 21
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Charge your
iPod/iPhone/
Load the iPod/iPhone/iPad
1 Connect the AC power cord to
‡ꢀ the ~ DC IN socket on the docking
charger.
iPad through
the separate
‡ꢀ the wall power socket.
docking charger
UK
You can charge your iPod/iPhone/iPad through
the supplied separate docking charger.
EUR
Compatible iPod/iPhone/iPad
The separate docking charger supports charge
of the following iPod, iPhone, and iPad models.
‡ꢀ iPad 2
‡ꢀ iPad
‡ꢀ iPhone 4
‡ꢀ iPhone 3GS
ON/OFF
‡ꢀ iPhone 3G
‡ꢀ iPhone
‡ꢀ iPod classic
‡ꢀ iPod 5G
‡ꢀ iPod 4G
‡ꢀ iPod nano (2nd, 3rd, 4th, 5th, and 6th
generation)
‡ꢀ iPod touch (1st, 2nd, 3rd, and 4th
generation)
22 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Place the iPod/iPhone/iPad in the docking
charger.
» The docked iPod/iPhone/iPad begins to
charge as soon as the docking charger
is connected to AC power.
To remove the iPod/iPhone/iPad
‡ꢀ Pull the iPod/iPhone/iPad out of the
docking charger.
EN 23
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Update
firmware
Update from the
FRQÀJXUDWLRQꢁSDJH
Warning
‡ Always connect your DS9800W to AC power for
ÀUPZDUHꢀXSJUDGHꢅꢀ1HYHUꢀSRZHUꢀRIIꢀ\RXUꢀ'6ꢉꢊꢋꢋ:ꢀ
GXULQJꢀÀUPZDUHꢀXSJUDGHꢅ
To improve the performance of DS9800W,
3KLOLSVꢀPD\ꢀRIIHUꢀ\RXꢀQHZꢀÀUPZDUHꢀIRUꢀXSJUDGHꢀ
of your DS9800W.
com/welcome for information about the latest
ÀUPZDUHꢅ
Note
‡ To use an Internet browser other than Apple Safari
on your PC/Mac, remember to go to the Wi-Fi router
FRQÀJXUDWLRQꢀSDJHꢀDQGꢀZULWHꢀGRZQꢀWKHꢀ,3ꢀDGGUHVVꢀRIꢀ
your DS9800W. See the user manual of your Wi-Fi
URXWHUꢀIRUꢀKRZꢀWRꢀÀQGꢀWKHꢀ,3ꢀDGGUHVVHVꢀRIꢀGHYLFHVꢀ
connected to the Wi-Fi router.
Note
‡ <RXꢀFDQꢀRQO\ꢀXSGDWHꢀWKHꢀÀUPZDUHꢀIURPꢀDꢀ3&ꢎ0DFꢅ
1 Power on DS9800W (see 'Prepare' on
page 10).
'RZQORDGꢁWKHꢁXSGDWHꢁÀOH
» It takes about 35 seconds for the unit
to boot up. During boot-up, the LED
indicator on the back of the main
VSHDNHUꢀEOLQNVꢀJUHHQꢀTXLFNO\ꢅꢀ
» After boot-up, you can hear a beep
and the LED indicator turns to green
steadily. DS9800W is connected to
WKHꢀODVWꢀFRQÀJXUHGꢀ:Lꢈ)LꢀQHWZRUNꢀ
automatically.
XXXX
2 Make sure that DS9800W and your PC/
Mac are connected to the same Wi-Fi
router.
3 Open Apple Safari on your PC/Mac, then
select 'Philips_Fidelio XXX' from the
Bonjour pull-down list.
XXXX. zip
‡ꢀ Or open another Internet browser
on your PC/Mac, then type in the IP
address of DS9800W (available on the
:Lꢈ)LꢀURXWHUꢀFRQÀJXUDWLRQꢀSDJHꢌꢀDWꢀWKHꢀ
address bar.
support.
2
3
(QWHUꢀWKHꢀPRGHOꢀQXPEHUꢀWRꢀÀQGꢀWKHꢀODWHVWꢀ
ÀUPZDUHꢀXSJUDGHꢀÀOHꢀDYDLODEOHꢅ
» ꢀ7KHꢀ'6ꢉꢊꢋꢋ:ꢀFRQÀJXUDWLRQꢀZHEꢀ
page is displayed.
ꢀ6DYHꢀWKHꢀXSJUDGHꢀÀOHꢀWRꢀ\RXUꢀKDUGꢀGULYHꢅ
24 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Select the Firmware Update tab, then
follow the on-screen instruction to
FRPSOHWHꢀWKHꢀÀUPZDUHꢀXSGDWHꢅ
Note
‡ ,QꢀFDVHꢀWKHꢀÀUPZDUHꢀXSGDWHꢀIDLOVꢄꢀ\RXꢀFDQꢀWU\ꢀWKHꢀDERYHꢀ
procedures again.
‡ $IWHUꢀVXFFHVVIXOꢀÀUPZDUHꢀXSGDWHꢄꢀLIꢀWKHUHꢀLVꢀDQ\ꢀ
problem with the Wi-Fi connection, press and hold
on DS9800W for more than 5 seconds at the same
time to reset the device, and then try to set up the Wi-
Fi network for DS9800W again (see 'Connect to your
home Wi-Fi network for AirPlay' on page 12).
EN 25
Download from Www.Somanuals.com. All Manuals Search And Download.
General information
8 Product
information
AC power
Wireless SoundSphere
speakers:
ꢐꢋꢋꢈꢁꢂꢋ9aꢄꢀꢒꢋꢎꢃꢋ+]
Separate docking charger:
Model:ASSA28-050200
,QSXWꢆꢀꢐꢋꢋꢈꢁꢂꢋ9aꢒꢋꢎꢃꢋ+]ꢀ
0.45A
Note
‡ Product information is subject to change without prior
notice.
Output: 5.0V
2000mA
Operation
Power
22 W
Consumption
Eco Standby
Power
6SHFLÀFDWLRQV
< 0.5 W
Consumption
Dimensions
$PSOLÀHU
- Each speaker 265 in diameter x 410 mm
Weight
- With Packing 14.5 kg
Rated Output Power
)UHTXHQF\ꢀ5HVSRQVH
Signal to Noise Ratio
Aux Input (MP3 link)
2X50 W RMS
ꢁꢋꢀꢈꢀꢁꢋꢋꢋꢋꢀ+]ꢄꢀꢈꢏG%
> 90 dB
- Speakers
12 kg
1V RMS 20 kohm
Speakers
Speaker Impedance
Speaker Driver
8 ohm
130 mm woofer + 19
mm tweeter
Sensitivity
> 85 dB/m/W
Wireless
Wireless
standard
Wireless
security
)UHTXHQF\ꢀ
range
802.11b/g
WEP (64 or 128 bit),
WPA/WPA2 (8-63 characters)
ꢁꢂꢐꢁꢀꢈꢀꢁꢂꢃꢁꢀ0+]ꢀꢍ&+ꢐꢈ
CH11) (for /79, /37, /55, /97)
ꢁꢂꢐꢁꢀꢈꢀꢁꢂꢑꢁꢀ0+]ꢀꢍ&+ꢐꢈ
CH13) (for /12, /10, /05)
Yes
PBC (one
button push)
26 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
‡
‡
Reduce the distance between the remote
control and the unit.
Insert the battery with its polarities (+/–
signs) aligned as indicated.
Replace the battery.
Aim the remote control directly at the IR
sensor on the front of the main speaker.
9 Troubleshooting
Warning
‡
‡
‡ Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair
the system yourself.
Wi-Fi network connection failed
‡
Check if yourWi-Fi router isWi-Fi 802.11b/g
FHUWLÀHGꢅꢀ7KLVꢀGHYLFHꢀLVꢀRQO\ꢀFRPSDWLEOHꢀZLWKꢀ
:Lꢈ)LꢀꢊꢋꢁꢅꢐꢐEꢎJꢀFHUWLÀHGꢀURXWHUVꢅ
If you encounter problems when using this
apparatus, check the following points before
UHTXHVWLQJꢀVHUYLFHꢅꢀ,IꢀWKHꢀSUREOHPꢀUHPDLQVꢀ
unsolved, go to the Philips web site (www.
philips.com/welcome).When you contact
Philips, ensure that the apparatus is nearby
and the model number and serial number are
available.
‡
If your Wi-Fi router is Wi-Fi 802.11n
FHUWLÀHGꢄꢀPDNHꢀVXUHꢀWRꢀHQDEOHꢀWKHꢀ
802.11b/g mode. DS9800W does not
support connection to routers with
802.11n only.
‡
‡
This device does not support the WPS-
PIN method.
No power
If your Wi-Fi router supports WPS and
the WPS-PBC method but fails to connect
to DS9800W, try the manual Wi-Fi setup
method (see 'Scenario 2: Connect to a
non-WPS router' on page 13).
‡
Make sure that the AC power plug of the
device is connected properly.
Make sure that there is power at the AC
outlet.
‡
‡
‡
Enable SSID broadcast on the Wi-Fi router.
Keep away from potential sources of
interference which may affect Wi-Fi signal,
such as microwave ovens.
If you fail to use your PC for Wi-Fi network
setup, check whether your PC is using a
Wi-Fi network.You cannot use Ethernet
connection for AirPlay network setup.
Make sure that the SSID name of your
home router consists of alphanumeric
characters, with no space or special
characters like %/#/* inserted.
If you choose to rename the AirPlay device
'Philips_Fidelio XXXX' in the setting menu,
do not use special characters or symbols.
For some new types of Wi-Fi routers, a
network name (SSID) may be created
automatically when you use WPS for
connection.Always change the default
network name (SSID) to a simple one that
consists of alphanumerical characters, and
also change the Wi-Fi security mode to
secure your network.
No sound
‡
‡
Adjust the volume.
Check the network connection. Set up the
network again if needed (see 'Connect to
your home Wi-Fi network for AirPlay' on
page 12).
‡
‡
‡
Check if you have selected the correct
audio source.
No response from the unit
‡
Press and hold on DS9800W for more
than 5 seconds to reset the device.Then
set up the Wi-Fi network for DS9800W
again (see 'Connect to your home Wi-Fi
network for AirPlay' on page 12).
‡
‡
‡
Disconnect and reconnect the AC power
plug, and then switch on the device again.
Remote control does not work
‡
%HIRUHꢀ\RXꢀSUHVVꢀDQ\ꢀIXQFWLRQꢀEXWWRQꢄꢀÀUVWꢀ
select the correct source with the remote
control instead of the main unit.
EN 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Occasional breaking of AirPlay music
streaming
Do one or all of the following:
‡
‡
‡
‡
Move DS9800W closer to your Wi-Fi
router.
Remove any obstacles between DS9800W
and your Wi-Fi router.
Avoid using Wi-Fi channel which is
overlapped by the nearby Wi-Fi network.
Check if your network speed is fast enough
(in cases where multiple devices share the
same router, the AirPlay performance may
be affected).Turn off the other devices
connected to your home router.
Enable the Quality of Service (QoS)
option (if available on the Wi-Fi router).
Turn off other Wi-Fi routers.
‡
‡
No AirPlay icon on my iTunes host device
‡
Make sure that DS9800W is already
connected to your home Wi-Fi network.
Before you open iTunes, make sure that
you have enabled Bonjour service in
your PC.Take Windows XP for example:
to enable the service, you can click
Start->Control Panel, and double-click
AdministrativeTools-> Services->Bonjour
Service, then click Start followed by OK
on the pop-up menu.
‡
‡
If the problem remains, try to restart
DS9800W.
AirPlay connection failed with Mac or PC
‡
7HPSRUDULO\ꢀGLVDEOHꢀWKHꢀÀUHZDOOꢀDQGꢀ
security software to see whether it blocks
the ports that AirPlay uses to stream
content. See the help documentation of
\RXUꢀÀUHZDOOꢀDQGꢀVHFXULW\ꢀVRIWZDUHꢀRQꢀKRZꢀ
to unblock the ports used by AirPlay.
When you use iPodTouch/iPhone/iPad/
Mac/PC for AirPlay, if the music play breaks
or stops, try to restart your iPodTouch/
iPhone/iPad, iTunes or DS9800W.
‡
‡
Video streaming or FTP downloads may
overload your router and therefore may
cause interruptions during AirPlay music
play.Try to reduce the load of your router.
28 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications are subject to change without notice
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
DS9800W_10_UM_V1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|