Philips Computer Monitor BDL4635E User Manual

Public Signage Solutions

User Manual

TYPE NR.

BDL4635E

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

SAFETY INSTRUCTIONS

WARNINGS AND PRECAUTIONS

KNOW THESE SAFETY SYMBOLS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any

inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included

with this product.

Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article

820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as

practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to

operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la bome correspondante

de la prise et pousser jusqu’au fond.

Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement

of U.S. copyright laws. Certain Canadian programs may also be copyrighted and any unauthorized recording in whole

or in part may be in violation of these rights.

TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

The Socket-outlet shall be installed near the apparatus and shall be easily accessible.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

REGULATORY INFORMATION

CE DECLARATION OF CONFORMITY

MMD declare under our responsibility that the product is in conformity with the following standards

• EN60950-1:2001 (Safety requirement of Information Technology Equipment)

• EN55022:2006 (Radio Disturbance requirement of Information Technology Equipment)

• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)

• EN6100-3-2:2000+A2:2005 (Limits for Harmonic Current Emission)

• EN6100-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker)

following provisions of directives applicable

• 73/23/EEC (Low Voltage Directive)

• 2004/108/EC (EMC Directive)

• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on

ISO9000 level.

WARNING

This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required

to take adequate measures.

FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

In a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING

EQUIPMENT REGULATIONS.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works

together (computer, monitor, printer, and so on) should have the same power supply source.

The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with

a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be

located near the equipment and easily accessible.

A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-

42107 and PN-89/E-06251.

ELECTRIC, MAGNETIC AND ELECTRONMAGNETIC FIELDS (“EMF”)

1. MMD manufactures and sells many products targeted at consumers, which, like any electronic apparatus, in general

have the ability to emit and receive electromagnetic signals.

2. One of MMD’ leading Business Principles is to take all necessary health and safety measures for our products, to comply with all

applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products.

3. MMD is committed to develop, produce and market products that cause no adverse health effects.

4. MMD confirms that if its products are handled properly for their intended use, they are safe to use according to scientific evidence

available today.

5. MMD plays an active role in the development of international EMF and safety standards, enabling MMD to anticipate further developments

in standardization for early integration in its products.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

INFORMATION FOR UK ONLY

WARNING - THIS APPLIANCE MUST BE EARTHED.

Important:

This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this

type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an

appropriate 3-pin plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug

without a fuse is used, the fuse at the distribution board should not be greater

than 5A.

Note: The severed plug must be destroyed to avoid a possible shock hazard should it

be inserted into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code:

BLUE - “NEUTRAL” (“N”)

BROWN - “LIVE” (“L”)

GREEN & YELLOW - “EARTH” (“E”)

1. The GREEN AND YELLOW wire must be connected to the terminal in

the plug which is marked with the letter “E” or by the Earth symbol or

coloured GREEN or GREEN AND YELLOW.

2. The BLUE wire must be connected to the terminal which is marked with the letter

“N” or coloured BLACK.

3. The BROWN wire must be connected to the terminal which marked with the letter

“L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the

sheath of the lead - not simply over the three wires.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求)

产品中有毒有害物质或元素的名称及含量

有毒有害物质或元素

汞镉六价铬多溴联苯多溴二苯醚

（Pb）（Hg）（Cd）（Cr 6+）（PBB）（PBDE）

部件名称

铅

外壳

○

× ×

○

液晶面板

电路板组件

○

附件

遥控器，电源线，连接线)

(

遥控器电池

○

○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006

标准规定的限量要求以下 ◦

×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出

SJ/T11363-2006 标准规定的限量要求 ◦

环保使用期限

此标识指期限(十年)，电子信息产品中含有的有毒有害物质或元素在正常使用的条件下不会发生外

泄或突变，电子信息产品用户使用该电子信息产品不会对环境造成严重污染或对其人身、财产造

成严重损害的期限。

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

NORTH EUROPE (NORDIC COUNTRIES) INFORMATION

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

END-OF-LIFE DISPOSAL

Your new TV/Monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the

amount of reusable materials and to minimize the amount to be disposed of.

Please find out about the local regulations on how to dispose of your old monitor from your local Philips dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on

recycling contact www.eia.org (Consumer Education Initiative)

WASTE ELECTRICAL AND ELECTRONIE EQUIPMENT-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG

governing used electrical and electronic appliances, this product may not be disposed of with normal

household waste. You are responsible for disposal of this equipment through a designated waste electrical

and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local

government office, the waste disposal organization that serves your household or the store at

which you purchased the product.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Contents

The BDL4635E monitor pack* should include:

•

LCD monitor

•

Screw for Clamper (T

Main switch cover

Screw for Main Switch cover

Cable Holder

prevent from falling)

Power cord (1.8 m)

VGA Signal Cable (1.8 m)

DVI-HDMI Cable (1.8 m)

User Manual

BNC TO RCA adapter x 5

Logo guider

Remote Control and AAA Batteries

Clamper

prevent from falling)

Cable belt

(For tightening cables)

Xxxxxxxxxxxxxx

xxxxxxxxxxxxxx

xxxxx

BNC TO RCA adapter x 5

Screw for Clamper

User’ Manual

Screw for Main switch cover

(3 6)

(M4

12)

Main switch cover

Cable Holder

Clamper

(To

prevent from falling)

The supplied power cor varies depending on destination.

Cable belt

(For tightening the power cor

and VGA / HDMI cable)

For North

America

For EU

For China

Power cor

Remote Control and AAA

Batteries

Please make sure that for all other regions, apply a power cord that conforms

to the AC voltage of the power socket and has been approved by and complies

with the safety regulations of the particular country

Stand

You might like to save the package box and packing material for shipping

the monitor

DVI-HDMI Cable

The following components are prepared as options.

•

External Speakers

Table stand

Video Signal Cable

Logo guider

(D-SUB to D-SUB Cable)

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Elements Name and Functions

Control Panel

Button

POWER button ( ) :To switch the power on/off.

MUTE button : To switch the audio mute ON/OFF.

INPUT button : To set the function while OSD menu is on or to toggle switch between [HDMI1], [HDMI2], [PC-A], [CVI], [VIDEO<S>] and

[VIDEO] while OSD menu is off

PLUS (+) button :To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is off.

MINUS (-) button :To decrease the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is off.

UP (S) button : To move the highlight bar up to adjust the selected item while OSD menu is on, or to activate the OSD menu when the OSD

menu is off.

DOWN (T) button :To move the highlight bar down to adjust the selected item while OSD menu is on, or to activate the OSD menu when

the OSD menu is off.

EXIT button :To return to previous menu while OSD menu is on or to activate the OSD menu when the OSD menu is off.

Remote control sensor and Power indicator : To receive the IR signal from the remote control. The indicator would show green

when the LCD monitor is active and would turn red when the LCD is POWER OFF. While in the case of the system is in power save mode, it would

show both green and red. When SCHEDULE is enabled, it would blink green and glow red. If the indicator blinks red , it tells that a failure is

detected.

Main Power Switch : To turn the main power on/off.

NOTE: Keyboard Control Lock Mode This function completely disables the access to all Keyboard Control functions. To enable the

keyboard control lock, press both of “S” and “T” buttons and hold down continuously for more than 3 seconds. To recover back to the user mode,

press both of “S” and “T” and hold continuously for three 3 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Terminal Panel

AUDIO IN 1, 2, 3

To input audio signal from external equipment such as a computer,VCR or DVD player.

AUDIO OUT

To output the audio signal from the AUDIO IN 1,2 and 3 jack.

EXTERNAL CONTROL (mini D-Sub 9 pin)

This is for serial connection when multiple BDL4635E monitors are connected. To achieve the remote control through RS232 command (refer to the

RS232 remote control user manual), connect the IN connector with the RS-232C OUT connector from the computer or a multi-connected BDL4635E

monitor and connect the OUT connector with the RS-232C IN connector of BDL4635E monitor.

VIDEO IN/OUT

VIDEO IN connector (BNC and RCA): To input a composite video signal. Note that BNC and RCA are not available at the same time.

VIDEO OUT connector (BNC): To output the composite video signal fromVIDEO IN connector.

S-VIDEO IN connector (MINI DIN 4 pin): To input the S-video (Y/C separate signal).

EXTERNAL SPEAKERTERMINAL

To output the audio signal to external speakers from AUDIO IN 1, 2, 3 jack or HDMI.

AC IN connector

To connect with the supplied power cord.

HDMI 1 IN

To input digital RGB signals from a digital equipment or computer.

*This connector does not support analog input.AUDIO is supported via HDMI.

HDMI 2 IN

To input digital RGB signals from a digital equipment or computer.

*This connector does not support analog input.AUDIO is supported via HDMI.

PC-A IN (mini D-Sub 15 pin)

To input analog RGB signals from a computer or other RGB equipment.

RGB OUT (mini D-Sub 15 pin)

To output the signal from PC-A IN.

CVI IN [Y, Pb/Cb, Pr/Cr] (BNC)

To Connect an equipment such as a DVD player, HDTV device, or Laser disc player.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Remote Control

SET button

To activate the setting with OSD menu.

AUTO ADJUST button

execute the AUTO ADJUST function.

MUTE button

To turn the mute function on/off.

VIDEO SOURCE button

To set the video source by toggle selection from [HDMI1], [HDMI2],

[PC-A], [CVI], [VIDEO<S>] and [VIDEO].

AUDIO SOURCE button

To set the audio source by toggle selection from [AUDIO1] to [AUDIO2],

[AUDIO3] and [HDMI]

Note 1: You cannot select the audio source for video source is set to

[VIDEO<S>] or [VIDEO].

Note 2: [HDMI] is selectable only when the video source is [HDMI 1] or

[HDMI 2].

SIZE button

To select the pictur

size from [FULL], [NORMAL], [CUSTOM] , [DYNAM

IC] and [REAL].

BRIGHTNESS button

To start the BRIGHTNESS OSD selection, and then push "+" or "-"

POWER button

button to adjust the value.

To turn the power on/off.

If LED Power Indicator on the monitor is not lightening, then the

remote control will not work.

UP button

To move the highlight bar up to adjust the selected item when OSD menu

is on.

SMART PICTURE button

To select smart picture mode from [HIGHBRIGHT], [STANDARD],

To move the sub-picture up when in “PIP” mode.

[sRGB], [CINEMA]

HIGHBRIGHT: for moving image such as Video

STANDARD: for images (Factory setting)

sRGB: for text based images

MENU button

o turn the OSD menu on/off.

PLUS button

CINEMA: for movies.

increase the adjustment with OSD menu.

PIP (Picture In Picture) button

To move the sub-picture right when in “PIP” mode.

ON/OFF button: To turn PIP mode ON/OFF.

INPUT button: To select the input signal for the sub-picture.

CHANGE button: To exchange between the main picture and sub-

picture.

EXIT button

turn to the previous OSD menu.

Note:

The “PIP” and “POP” modes do not work if the screen size is

“CUSTOM” or “REAL”.

DOWN button

To move the highlight bar down to adjust the selected item when OSD

menu is on.

CONTRAST button

To start CONTRACT OSD selection, and then push "+" or "-" button

to adjust the value.

To move the sub-picture down when in “PIP” mode.

VOLUME UP button

To increase the audio output level.

DISPLAY button

To turn on/off the setting information displayed on the right-up corner

of the screen.

VOLUME DOWN button

To decrease the audio output level.

MINUS button

To decrease the adjustment with OSD menu.

To move the sub-picture left when in “PIP” mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Operating Range for the Remote

Control

Handling the remote control

Do not subject to strong shock.

Do not allow water or other liquid to splash the remote control.

Point the top of the

sensor during button operation.

Use the emote control within

front of the LCD monitor's emote control sensor and within

emote control towar

the LCD monitor's remote

If the

remote control gets wet, wipe it dry immediately.

Avoid exposure

to heat and steam.

distance of about

m/23 ft from the

Other than to install the batteries, do not open the

control.

remote

horizontal and vertical angle 30° with

distance of about

m/10 ft.

30° 30°

NOTE:

strong illumination strikes the

or when ther is an obstacle in the radiation path.

remote control system may not function when direct sunlight or

remote control sensor of the LCD monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

How to Mount or AttachTable stand to the LCD Monitor

You can install the LCD monitor in one of the following two ways:

Way 1: Attach and r

How to install Table stand

1. Please turn the monitor off.

emove the optional Table stand

2. After inserting Table stand in guide block, fasten the thumbscrews on both sides of the monitor

NOTE:

Install the Table stand with their longer portions directing to the front.

Screws

Longer portions directs to the front

Optional Table stand

In the upright position

How to remove the Table stand

1. Spread the protective sheet on the flat surface

2. Make the monitor lying on the protective sheet.

3. Remove screws using screwdriver and place them in

safe place for reuse.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

To avoid monitor from falling

Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and

damage.

As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the

monitor(BDL4635E: approx. 34.6 kg). Screw hooks (commercially available), of ring type rather than C-shaped screw hooks (with opening), are

recommended.

Screw Holes

Screw hook

Rope

Clamper

Screw

* Clamper and Screw here is not supplied.

Caution:

y Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn’t assure its effectiveness

against any kind of earthquake or disaster.

y Before moving the monitor, remove the rope that is securing the monitor.

Way II: Mount the monitor on the wall

Before mounting the monitor to the wall, make sure that the system has been power-off and you have obtain a standard wall-mounting kit

(commercially available). Using mounting interface that comply withTÜV-GS and/or UL1678 standard in North America is recommended.

Protective Sheet

Tabletop stand

Table

Handles

1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch

the screen face.

2. This device cannot be used or installed without the Tabletop Stand or other mounting accessory. Make sure all these stuffs are ready for wall-

mount installation.

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the

equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them

securely. (Recommended torque: 470 - 635N•cm).

Caution:

For preventing the monitor from falling.

y Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed procedures of

installation, refer to the instructions of the metal brackets.

y To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to consult the

bracket manufacturer for installation location.

y To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through the handles

at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets.(Refer to the first paragraph of this

page.)

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Ventilation Requirements for enclosure locating

To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Setup Procedur

1. Install the system on the right location

3. Connect to external equipment

•

protect the connected equipment, tur

befor making connections.

Please refer to section “Connectivity” P.18~P.22 for operations.

off the main power

CAUTION:

THE LCD MONITOR MUST BE MOVED OR INSTALLED BY

TWO OR MORE PERSONS.

•

Failur to follow this caution may result in injury if the LCD

4. Connect power cord

monitor falls.

•

The power outlet socket should be installed as near to the

equipment as possible, and should be easily accessible.

Fully insert the prongs into the power outlet socket. Loose

connection may cause noise.

CAUTION:

DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY

•

YOURSEL

The LCD display must be installed by

Contact your dealer for mor information.

qualified technician.

NOTE:

Please efer to “Safety Operation” section of this manual for

CAUTION:

DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN,

proper selection of AC power cord

Cable belt

Cable Holder

FACE UP, OR FACE DOWN

CAUTION:

DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE

EXPOSED TO DIRECT SUNLIGHT.

Failur to follow this caution will result in display defects.

IMPOR

ANT

Lay the protective sheet, which was wrapped around the LCD monitor

when it was packaged, beneath the LCD monitor so as not to scratch

the panel.

2. Install the remote control batteries

The

install or replace batteries:

1. Press and slide to open the cover

emote control is powered by 1.5V AAA batteries.

2. Align the batteries according to the (+) and (–) indications inside

the case.

Use the Cable belt

to secure the

cables firmly.

3. Replace the cover

5. Turn on the power of the

ttached external equipment

CAUTION:

When connected with

computer, turn on the power of the computer

Incorrect use of batteries can result in leaks or bursting. Be

careful especially about the following points.

first.

•

Place “AAA” batteries matching the

and signs on each battery

6. Operate the attached external equipment

to the and signs of the battery compartment.

Display the signal from the external equipment

•

Do not mix battery types.

Do not combine new batteries with used ones. It causes shorter

battery life or leakage of batteries.

7. Adjust the sound

Make adjustments to lower or to rise the volume as required.

•

Remove dead batteries immediately to prevent battery

liquid from leaking into the battery compartment. Don't touch

exposed battery acid, it cause damage to your skin.

8. Adjust the screen

Make adjustments to the display position or settings if

required.

NOTE:

If you do not intend to use the Remote Control for

remove the batteries.

long period,

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

9. Adjust the image

Make adjustments to brightness or contrast if required.

10. Recommended Adjustment

educe the risk of “image persistence”, please adjust the

following items based on the application being used.

“POWER SAVE” “PANEL SAVING” “SIDE BORDER COLOR”

“DATE AND TIME” “SCHEDULE”

11. To prevent the main power switch

from being changed

prevent the possibility of main power switch being carelessly

pushed, please attach the main switch cover (accessory) onto it

NOTE:

With the main power switch cover in place, the main power switch

can not be turned off. Remove main power switch cover in order to

turn of the display.

Screw

Main switch cover

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Install the LCD Monitor in

ortrait

Mode

BDL4635E can be installed in portrait position, under the following conditions:

Caution:

Portrait mode is effective only when wall-mounted or ceiling-mounted. The Table stand can not be used for the monitor in portrait position.

Placing the monitor in portrait position, will shorten the average life of the LCD backlight.

Operational Environment (Temperature) shall be limited, as shown below:

Operational

Environment

mperatur

35 °C

41 95 °F

Humidity

(without condensation)

Please orientate the monitor in the direction shown as the right figure:

Do not place monitor in landscape in any other manner

Clockwise

Counterclockwise

How to set-up

1. Remove the Table stand if they are attached.

2. The

“

”

logo should be on the LEFT side when facing the monitor.

How to Remove the Logo for landscape mode?

1. Prepare a piece of paper with a cutting area of logo as a protector to

prevent the front bezel from scratching.

2. Using an knife, carefully remove the logo sticker with the paper placing

beneath.

3. Tear off the logo sticker.

How to Use the Logo Guider for Portrait Mode?

1. Before applying, make sure the guider is well shaped. The "PHILIPS"

sticker attached on the end of it could be folded back as figure a.

2.Turn back the logo end of the guider and remove the sticky tape of the

logo.

3. Slide the logo guider along the short side of the front bezel as figure c &

then re-turn the logo end of the guider back to the right side.

4. With your left hand fixing the guider, scrunch the logo by your right hand

to make it stuck firmly on the front bezel.

5. Remove the guider and leave the logo over the front bezel.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Connectivity

Befor making connections:

First tur

off the power of all the attached equipments before make connections.

Refer to the user manual included in each separate piece of equipment.

Connectivity Diagram

BDL4635E

DVD player

BDL4635E (second monitor)

Equipment with

Digital interface

HD or laser disk player

Personal

Computer

VCR

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Connecting to a Personal Computer

As you finish the connection between the computer and the LCD monitor, you could play the contents in the computer

and display them on the LCD monitor

Connecting the LCD Monitor to a Personal Computer

•

o achieve this

(PC-A IN connector)

When connecting mor

available) to make connection between LCD monitor(RGB OUT connector) and the other (PC-A IN connector)

The AUDIO IN 1, 2, 3 or HDMI can be connected for audio input using RCA cable After choosing one of the AUDIO IN connectors, you

apply the supplied VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection between PC and LCD monitor

than one LCD monitors to PC, apply another VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin; it’s commercially

might need to select AUDIO 1, 2, 3 or HDMI using the AUDIO SOURCE button on the remote control. HDMI (for audio) is selectable only

when HDMI 1 or 2(for video) is selected.

•

hen connecting mor

than one LCD monitors to PC, apply RCA cable to make connection between LCD monitor(AUDIO OUT connector) and

the other (AUDIO IN 1, 2, 3). HDMI source is not suitable for this case.

BDL4635E

PC or IBM compatible

audio output

analog RGB output

Mini D-sub 15 pin

RCA

Mini D-sub 15 pin

BDL4635E (second monitor)

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Connecting to a Digital Interface Equipment

Connections can be made between LCD monitor and other digital equipment that is equipped with digital interface compliant with the DVI (Digital

Visual Interface) standard.

Connect the LCD Monitor to

Computer with

Digital Output

•

The HDMI 1

HDMI 2 IN connector accepts

HDMI cable.

The HDMI 1

HDMI 2 IN connector can be chose to receive the video signal from HDMI output(applying HDMI to HDMI cable) or DVI-D

output (applying HDMI to DVI cable) of PC.

ensure the display quality use cable with

The AUDIO IN 1, 2, 3 or HDMI connector can be chose to receive audio source

button on the remote control. HDMI(for audio) is only selectable only when HDMI 1 or 2(for video) is selected.

Note that the signal input from HDMI connector cannot be output to the RGB OUT connector

•

quality prescribed by DVI standards.

Select AUDIO 1, 2, 3 or HDMI from the AUDIO SOURCE

•

BDL4635E

audio output

HDMI output or DVI-D

Equipment with

such as personal computer with

RGB output (TMDS)

digital interface

HDMI connector

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Connecting to a DVD Player

As you finish the connection between the DVD player and the LCD monitor, you could display the contents from the played DVD on the LCD

monitor. You might like to refer to your DVD player manual for further information.

’s

Connect the LCD Monitor to

DVD Player

•

o achieve this

DVD player(Y, Cb/Pb, Cr/Pr Out) and LCD monitor (CVI In). You might need BNC-to-RCA adapters(including in the accessories) to convert

the BNC connectors to RCA connectors if you are using the separated signaling(Y, Cb/Pb, Cr/Pr) RCA cable

If your DVD player supports HDMI signaling, apply HDMI to HDMI cable for the connection

apply separated signaling(Y, Cb/Pb, Cr/Pr) BNC cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection between a

•

The AUDIO IN 2 , 3 (both of RCA connector type) can be used for audio input.

Select [AUDIO 1] ( for 3.5φ phone jack), [AUDIO 2], [AUDIO 3]

Or [HDMI] from the AUDIO SOURCE button on the remote control. HDMI (for audio) is selectable only when HDMI 1 or 2 (for video) is

selected.

BD_BL_D4_L6₄5₆₃3₅V_E

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Connecting to a Stereo Amplifier

You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier's manual for further information.

Connect the LCD Monitor to

Stereo Amplifier

•

urn on the LCD monitor and the amplifier only after all connections have been finished.

Apply an RCA cable to make connection between the amplifier (audio in) and the LCD monitor

Do not verse the audio left and right jacks.

(

audio out).

For the preferring audio signal, select [AUIDO1], [AUDIO2], [AUDIO3] or [HDMI] from the AUDIO SOURCE button on the remote control.

HDMI(for audio) is selectable only when HDMI 1 or 2(for video) is selected.

•

The AUDIO OUT RCA connectors output sound from the selected AUDIO SOURCE.

BDL4635E

RCA

BNC

RCA

BNC

RCA

BDL4635E (second monitor)

External speaker

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will tur

of using the following three options:

green while powered on and will turn

red while powered off

The monitor can be powered on or

1. Pressing the Main Power Switch.

NOTE:

When the Main Power Switch is used to power of

LCD monitor the emote control the power button and the indicator

will not work. Make sur to tur the Main Power Switch on befor

using the other two options.

the

Main Power Switch

2. Pressing the power button.

NOTE:

Befor

pressing the power button, be sure to turn on the

Main Power button on the LCD monitor

Power Button

3. Using the

remote control.

NOTE:

Befor

operating the remote control, be sure to turn on the Main

Power Switch on the LCD monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Power Indicator

Status

Power ON

Green

Power OFF

Red

Power Standby when

“SCHEDULE” is enable

Power Standby

Diagnosis

Red On

Green Blinking

Red, Green

Red Blinking

* See troubleshooting

(Detecting failure)

Using Power Management

The LCD monitor follows theVESA approved DPM Power Management function.

The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or

the mouse has not been used for a certain period.

The power management feature on the LCD monitor has been set to the “ON” mode. This allows the system to enter a Power Saving Mode when no

signal is applied. This could potentially increase the life and decrease the power consumption of the LCD monitor.

Display Signal ofVideo Source Setting to [VIDEO]

Use the input button on the front panel or theVIDEO SOURCE button on the remote control to set video source to [VIDEO].

Use the COLOR SYSTEM OSD menu to select [AUTO], [NTSC], [PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.

Picture Size

HDMI 1, 2, PC-A

FULL

NORMAL

CUSTOM

REAL

CVI , VIDEO

DYNAMIC

REAL

CUSTOM

SignalType

4:3

NORMAL SIZE

Recommended Size

NORMAL

DYNAMIC

FULL

Squeeze

NORMAL: Display with the input signal aspect ratio from PC signal, or display in 4:3 aspect ratio at CVI orVIDEO signal.

FULL: Display in the entire screen.

DYNAMIC: Expand 4:3 pictures to the entire screen with non-linearity. (Some round image might be cut by expansion.)

CUSTOM (ZOOM): Images can be expanded beyond the active display area. The image which is outside of the active display area would not be

shown.

REAL: Image will be displayed for one by one pixel.

ZOOM

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Smart Picture Mode

HDMI 1, 2, PC-A

HIGHBRIGTH

STANDARD

sRGB

CVI,VIDEO

HIGHBRIGTH

CINEMA

Audio Source Switching

You can select the audio source using the AUDIO SOURCE button on the remote control.

HDMI 1, 2

HDMI

AUDIO1

AUDIO2

AUDIO3

Other than HDMI 1, 2

AUDIO1

AUDIO2

Control Lock Mode

This function disables the operation o buttons so that the adjustments you make are not active when they are pressed.

To disable the buttons, press and hold down the S and T buttons together for at least 3 seconds.

To enable the buttons, press and hold down the S and T buttons together for at least 3 seconds again.

OSD Information

HDMI, 2, PC-A

PC-A

1024

48kHz 60Hz

AUDIO : 1

ideo Source

768

Input signal Information

Audio Source

Pictur Size

SIZE FULL

CVI

AUDIO : 3

SIZE FULL

deo Source

Audio Source

Pictur Size

VIDEO<S>, VIDEO

VIDEO<S>

NTSC

AUDIO :3

Video Source

Color System of Input Signal

SIZE NORMAL

Audio Source

Pictur Size

PIP or POP

Main:PC-A

Sub:VIDEO<S>

PC-A

1024

768

Main pictur Information

48kHz 60Hz

AUDIO : 1

VIDEO<S>

NTSC

Sub pictur

Information

Main pictur

SIZE FULL

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

OSD (On-Screen-Display) Controls

Press SET button

to enable setting.

Press MENU or

EXIT button to exit.

Press MENU button to

open Main menu. Press

UP or DOWN button to

select sub-menu.

Press UP or DOWN, and PLUS or

MINUS button to select function, or

adjust the setting Press SET button

to enable the setting.

Remote Control

Press EXIT button to

open Main menu. Press

UP or DOWN button

to select.

Press INPUT button to

enable the setting.

Press UP or DOWN, and PLUS

or MINUS button to select

Press EXIT button to

exit.

function, or adjust the setting

Press INPUT button to enable

the setting.

Control Panel

UP or DOWN button

INPUT button

“-” “+” button

EXIT button

OSD screen

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Main-Menu

PICTURE

BRIGHTNESS

Adjusts the overall image and background screen brightness.

Press

button to increase brightness.

button to decrease brightness.

CONTRAST

Adjusts the image brightness for the input signal.

Press

button to increase contrast.

button to decrease contrast.

SHARPNESS

This function is digitally capable to keep crisp image at any timings.

It is adjustable to get

distinct image or soft one as you prefer and set independently for each

pictur mode.

Press

button to increase sharpness.

button to decrease sharpness.

BLACK LEVEL

Adjusts the image brightness for the background.

Press

button to increase black level.

button to decrease black level.

NOTE: sRGB pictur mode is standard and cannot be changed.

NOISE REDUCTION

INPUT VIDEO<S>, VIDEO only

Adjusts the noise reduction level.

Press

button to increase

button to decrease

eduction level.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

TINT

INPUT HDMI1, 2(HDMI INPUT MODE-HD), CVI, VIDEO<S>, VIDEO only

Adjusts the tint of the screen.

Press

button the flesh tone color becomes greenish.

button the flesh tone color becomes purplish.

COLOR

INPUT HDMI1, 2(HDMI INPUT MODE-HD), CVI, VIDEO<S>, VIDEO only

Adjusts the color of the screen.

Press

button to increase color depth.

button to decrease color depth.

COLOR TEMPERATURE

Is used to adjust the color temperature.

The image becomes

reddish as the color temperature decreases, and becomes bluish as the color

temperatur increases.

COLOR CONTROL

The color levels of red, green, and blue are adjusted by the color bars.

R: Red, G: Green, B: Blue

PICTURE RESET

Selecting Pictur

Select “Yes” and press “SET” button to

Press “EXIT” button to cancel and then retur

set allows you to

eset all OSD settings about PICTURE setting.

estor to factory preset data.

to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Main-Menu

SCREEN

POSITION

Controls Horizontal Image position within the display area of the LCD.

Press

button to move screen to right.

button to move screen to left.

POSITION

Controls Vertical Image position within the display area of the LCD.

Press

button to move screen to UP.

button to move screen to DOWN.

CLOCK

INPUT PC-A only

Press

button to expand the width of the image on the screen the right.

button to narrow the width of the image on the screen the left.

CLOCK PHASE

INPUT PC-A only

Improves focus, clarity and image stability by increasing or decreasing this setting.

ZOOM MODE

ou can select “FULL”, “NORMAL” and “CUSTOM” and “REAL”. (INPUT HDMI1,HDMI2,PC-A only)

You can also select “FULL”,“NORMAL” “DYNAMIC” and “CUSTOM” and “REAL”. (INPUT CVI,

VIDEO<S>, VIDEO only)

Selecting “DYNAMIC” will make the screen display panoramic with the expansion of the middle and

outside of the screen changed. (The upper and the bottom of the image will be cut by expansion.)

Dynamic image is the same as FULL size image when HDTV signal is input.

Selecting “REAL” image will be displayed

pixel.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

CUSTOM ZOOM

“CUSTOM ZOOM” will be selected when you select “CUSTOM” on the screen “ZOOM” mode.

ZOOM: expands the horizontal and the vertical size simultaneously.

HZOOM: expands the horizontal size only.

VZOOM: expands the vertical size only.

POSITION: moves to the right with

button. moves to the left with

button.

–

button.

POSITION: moves up with button. moves down with

–

SCREEN RESET

Selecting Screen eset allows you to

eset all OSD settings from PICTURE setting.

Select “Yes” and press “SET” button to estor the factory preset data.

to the previous menu.

Press “EXIT” button to cancel and then retur

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Main-Menu

AUDIO

BALANCE

Adjusts the balance of L/R volume.

Press

Sound of the left side will be small.

Press button to move the stereo sound image to left.

button to move the stereo sound image to right.

TREBLE

It is to accentuate or reduce the high frequency sound.

Press

button to increase TREBLE sound.

button to decrease TREBLE sound.

BASS

It is to accentuate or

reduce the low frequency sound.

Press

button to increase BASS sound.

button to decrease BASS sound.

AUDIO RESET

Selecting Audio eset allows you to

Select “YES” and press “SET” button to

Press “EXIT” button to cancel and then retur

eset all OSD settings from AUDIO setting.

estor the factory preset.

to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Main-Menu

PIP (PICTURE IN PICTURE)

Note: The “PIP” and “POP” modes do not function when the screen size is “CUSTOM” or “REAL”.

PIP SIZE

Selecting the size of pictur inserted at the “Picture-in-Picture” (PIP) mode.

“Large”, “Middle” and “Small” ar available.

PIP AUDIO

Selecting the sound source in PIP mode.

When selecting “MAIN AUDIO”, you will get the sound for the main pictur and when selecting

“PIP AUDIO”, you will get the sound for the pictur instead.

PIP RESET

Selecting PIP Reset allows you to

Select “Yes” and press “SET” button to

Press “EXIT” button to cancel and then retur

eset all OSD settings from PIP setting.

estor the factory preset data.

to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Main-Menu

CONFIGUR

AUTO ADJUST

TION

INPUT PC-A only

Press "SET" button to automatically adjust screen size, horizontal position, vertical position, clock,

clock phase, white level and black level.

Press "EXIT" button to cancel execution AUTO ADJUST and then will return to the previous menu.

POWER SAVE

Selecting RGB "ON", the monitor will go to power management mode when HDMI1,HDMI2,PC-A, sync is

lost.

Selecting VIDEO "ON", the monitor will go to power management mode after about 10 minutes delay

from when CVI and VIDEO input signal is lost.

LANGUAGE

OSD control menus ar available in eight languages.

(English, German, French, Italian, Spanish, Polish, Turkish, Russian, Simple Chinese

)

PANEL SAVING

Select "PANEL SAVING" functions to

reduce the risk of the "image persistence".

COOLING FAN: Regulation of temperature when the display working.

AUTO

ON in the state, displays the beginning of the state, fans will always open.

ased when selected "ON".

in the state .The fan will automatically open when the display reaches a certain temperature.

BRIGHTNESS: The brightness is decr

PIXEL SHIFT: Image is slightly expanded and moves 4 directions (U

(Need setting the time for movement).

DOWN, RIGHT LEFT) periodically

Movement area is approximately +/- 10mm from original position;

Please locate the important information such as text within 90% area of screen image.

See note (1) for this functions.

PIP and STILL will be disabled when "MOTION" is active.

COLOR SYSTEM

INPUT VIDEO<S>, VIDEO only

Selecting the Color System depends on your input video format.

AUTO: NTSC, PAL, SECAM, PAL60 or 4.43 NTSC is automatically selected.

NTSC: Specific selection of NTSC.

PAL: Specific selection of PAL.

SECAM: Specific selection of SECAM.

PAL-60: Specific selection of PAL60.

4.43NTSC: Specific selection of 4.43 NTSC.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

CONFIGURATION RESET

Selecting the CONFIGURATION RESET allows you to reset all configuration settings.

Select "Yes" and press "SET" button to

estor

the factory preset data.

Press "EXIT" button to cancel and etur

the previous menu.

ACTOR

RESET

Selecting "YES" allows you to

reset PICTURE, SCREEN, AUDIO, CONFIGURATION1,2 and

ADVANCED OPTION will be back to factory settings (except LANGUAGE, DATE AND TIME and

SCHEDULE).

Select "YES" and press "SET" button to restore the factory preset data. Press "EXIT" button to

cancel and

retur

the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Main-Menu

CONFIGUR

ATION

OSD TURN OFF

The OSD control menu will stay on as long as it is use. In the OSD

how long the monitor waits after the last touch of button to shut of

The preset choices ar -120 seconds.

urn Of

submenu, you can select

the OSD control menu.

INFORMATION OSD

Selects the information OSD display or not.

The information OSD will display when input signal or source change or warning message like as

no-signal or out-of range.

time between

to 10 seconds is available.

SLEEP TIMER

select SLEEP TIMER mode ON/OFF.

In the SLEEP TIMER menu, you can preset the monitor to automatically power down.

time between to 24 hours is available.

When the SLEEP TIMER is set, the SCHEDULE settings will be disabled.

OSD

POSITION

Adjusts the horizontal position of the OSD menu.

OSD

POSITION

Adjusts the vertical position of the OSD menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

MONITOR INFORMATION

Indicates the model and serial number of your monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Main-Menu

ADVANCED OPTION

INPUT RESOLUTION

INPUT PC-A only

Selects to decision of input signal about below timings, 1024x768, 1280x768 and 1360x768.

AUTO: Determines the esolution automatically

1024x768: Determines the

1280x768: Determines the

1360x768: Determines the

esolution as 1024x768

esolution as 1280x768

esolution as 1360x768

The setting you select becomes effective when POWER is turned OFF and ON again.

BLACK LEVEL EXPANSION

INPUT HDMI1,2(HDMI INPUT MODE-HD), VIDEO<S>, VIDEO only

Selects level of black expansion from “OFF”, “MIDDLE” and “HIGH.”

In case of go under the black cut-off level, please adjust the “Black level” in moderation on OSD menu.

GAMMA SELECTION

Selects

2.2

display gamma, It’s refer to the brightness performance curve of signal input.

2.4

gamma

Native

NOTE: sRGB pictur mode is standard and cannot be changed.

SCAN MODE

INPUT HDMI1,2(HDMI INPUT MODE-HD), CVI, VIDEO<S>, VIDEO only

Changes the display area of the image.

OVERSCAN: Set to display area about 95%

UNDERSCAN: Set to display area about 100%

SCAN CONVERSION

INPUT HDMI1,2(HDMI INPUT MODE-HD), CVI, VIDEO<S>, VIDEO only

Selects IP (Interlace to Progressive) converter function.

PROGRESSIVE: Enable the IP function, to convert interlace signal to progressive. Normally use

this setting.

INTERLACE*: Disable the IP function.

*NOTE: This mode is better suited for motion pictures, but it increases chance of image retention.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

FILM MODE

INPUT HDMI1,2(HDMI INPUT MODE-HD), CVI, VIDEO<S>, VIDEO only

Selects Film mode function.

AUTO: Enable the Film mode function. This mode is better suited for movies, which is converted 24

Frames/sec source to DVD ideo. ecommend to select “PROGRESSIVE” in “SCAN CONVERSION”.

OFF: Disable the Film mode function. This mode is better suited for Broadcasting or VCR source.

IR CONTROL

Selects the operation mode of the

RS-232C.

remote controller when multiple BDL4635E monitors are connected via

The item in this menu will become effective by pressing “SET” button on the selected item.

NORMAL: The monitor will be controlled normally by emote controller

PRIMARY The first BDL4635E monitor of those multi-connected via RS-232C is designated as PRIMARY

SECONDARY

designated as SECONDARY

LOCK: Disable the monitor control by infrared

BDL4635E monitors other than the first one multi-connected via RS-232C ar

emote controller

Keep pressing “DISPLAY” button during

sec or more, this setting will

tur

to “NORMAL”.

KEYBOARD CONTROL

Selects the operation mode of the keyboard control

Select “YES” to disable the keyboard.

Select “NO” to enable the keyboard.

TILING

TILING demonstrates multiple screens. This feature provides

It will be able to divide up to each and V.

This requires you to feed the PC output into each of the monitors through

MONITORS: Select number of horizontal divide.

MONITORS: Select number of vertical divide.

POSITION: Select position to expand the screen.

single large screen using up to 25 monitors.

distributor.

FRAME COMP: Works in tandem with TILING to compensate for the width of the tile bezels in order

to accurately display the image.

ENABLE: Select “YES”, the monitor will expand the selected position.

PIP and STILL will be disabled when “TILING” is activated.

DATE AND TIME

Adjusts the current date and time for internal clock.

You should set this function when you use “SCHEDULE”.

SCHEDULE

Programs the monitor's working schedule.

Schedule the power on and power off with hour and

This OSD can't remove except EXIT.

day of the week. Also sets the input port.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

MONITOR ID

ID numbers for remote control are assigned to BDL4635E monitors that are multi-connected via RS-232C.

ID numbers 1 to 26 are selectable.

DDC/CI

Use to turn ON or OFF the DDC/CI communication function. Select ON for normal use.

HEAT STATUS

HEAT STATUS allows you to watch the thermal status at any time via the OSD menu and/or via RS232

commands.The indicated temperature has a accuracy of 3 degrees (plus and minus)..

Press “SET” button to enter the submenu to monitor the heat status

Press “EXIT” button to cancel and then return the previous menu.

SMART POWER

Selecting SMART POWER allows you to choose a certain level of power saving condition.

Select “OFF” to set the system in normal power condition

Select “MEDIUM” to set the system in medium level power saving status.

Select “HIGH” to set the system in high level power saving status

Press “EXIT” button to cancel and then return the previous menu.

ADVANCED OPTION RESET

Selecting ADVANCED OPTION RESET allows you to reset all OSD settings from ADVANCED OPTION

settings, except for GAMMA SELECTION, DATE AND TIME, SCHEDULE, HDMI 1 INPUT MODE, HDMI

INPUT MODE, MONITOR ID, and DDC/CI.

Select “YES” and press “SET” button to restore the factory preset data.

Press “EXIT” button to cancel and then return the previous menu.

GAMMA SELECTION is reset when carrying out the PICTURE RESET in the PICTURE.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

NOTE

NOTE 1: IMAGE PERSISTENCE

Please be awar

“ghost” image of

image persistence is not permanent, but constant images being displayed for

alleviate image persistence, tur of the monitor for as long as the previous image was displayed. For example, if an

that LCD

echnology may experience

phenomena known as Image Persistence. Image Persistence occurs when residual or

monitors, LCD monitors’

long period of time should be avoided.

previous image remains visible on the screen. Unlike CR

image was on the monitor for one hour and

As with all personal display devices, PHILIPS

esidual image remains, the monitor should be turned of

ecommends displaying moving images and using moving panel saving at

the monitor when not in use.

for one hour to erase the image.

regular intervals

whenever the screen is idle or turning of

Please set “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME” and “SCHEDULE” functions to further

Image persistence.

reduce the risk of

For long life use of Public Display

< Image Sticking of LCD Panel

When LCD panel is operated continuously for long hours,

image of previous image may be observed. (Image Persistence)

Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD ar

the displayed image, and it is observed permanently. (Image Sticking)

trace of electric charge

emains near the electrode inside LCD, and

esidual or “ghost”

accumulated along

Recommendations

For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following ar

recommended.

1. Fixed image should not be displayed for long period, and changed to another images with short cycle.

2. In case a fixed image is display for a long time, it is advised to activate the pixel shift feature that will periodically move the image in four

directions

3. When no use, please tur

Function of monitor

4. Reducing the environmental temperatur

When Protection boar (glass, acryl) is installed over the LCD surface, enclosed into the box

temperatur sensors inside monitor

educe the environmental temperature, the monitor should be set Low Brightness or Cooling Fan “ON” by using Screen sever Function.

5. Please use "Panel saving Mode" of monitor

off

the monitor by

remote control, or use Power Management Function of monitor or use Schedule

is effective for long life use.

wall, or stack the monitor, please utilize the

NOTE 2: HOW TO SETUP SCHEDULE

Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated.

You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will

use for each scheduled activation period.

effect.

check mark in the box next to the number of the schedule indicates that the selected schedule is in

select which schedule to set, use the up/down arrows to move the number (1 to 7) of the schedule.

Use the (+) and (-) buttons to move the cursor horizontally within the particular schedule. Use the

and select input port. The “SET” button is used to make selection.

If you create schedule but do not want to use power on time, select “--” in the “ON” time slot.

If you do not want to use power of time select “--” in the OFF time slot.

If ther is no input selected (“--” showing in the input spot) the input from the previous schedule will be used.

The selection of EVERY DAY within schedule takes priority over other schedules that ar set up to operate weekly. When schedules

ar overlapping, scheduled Power ON time has priority over scheduled Power OFF time.

If ther ar two schedules programmed for the same time, then the highest numbered schedule has priority

TIMER is set, the “SCHEDULE” function is disabled.

(

)

and

(

)

buttons to increase time

When the “SLEEP

”

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

NOTE 3: “PIP”, “POP” and “SIDE BY SIDE”

The following table shows the combination of signal inputs under which the “PIP” and “POP” modes function. These modes do not function,

however, when the screen size is “CUSTOM” or “REAL”.

SUB

HDMI 1 HDMI 2 PC-A

CVI

VIDEO<S> VIDEO

HDMI 1

HDMI 2

PC-A

{

{: Supported

±: Not supported

CVI

VIDEO<S>

VIDEO

{

Press the “PIP ON/OFF” buttons on the

remote control to change between “PIP”, “POP” and “SIDE BY

SIDE” mode as shown in the diagram below

SIDE BY SIDE

ASPECT

SIDE BY SIDE

FULL

PIP

POP

OFF

A B

A A

“PIP”, “POP” mode resolution (Reference)

PIP SIZE

: 320 dots

: 480 dots

: 640 dots

: 320 dots

240 dots

320 dots

480 dots

240 dots

SMALL

MIDDLE

LARGE

POP SIZE

Remote control numbering function

By connecting multiple BDL4635E monitors using RS-232C cables, you can control any one monitor or all the monitors by one

remote controller.

1. Assign arbitrary ID number to each of multi-connected BDL4635E monitors using MONITOR ID. ID numbers 1

to 26 ar

It is recommended to assign sequential ID numbers from

2. The emote control mode of the first BDL4635E monitor is set to PRIMARY and those of the other monitors ar

SECONDARY

3. When you direct the

button on the emote controller

selectable.

and up.

set to

emote controller at the

remote control signal sensor of the PRIMARY monitor and press the DISPLAY

the ID selection OSD appears at the upper left of the screen.

ID number of the currently viewed monitor

Select the ID number of the monitor you want to control using the +/- button

on the remote controller.

The ID of the monitor you want to control is displayed at the upper left of its screen.

By selecting ALL, you can control all the multi-connected monitors.

4. Direct the

remote controller at the

emote control signal sensor of the PRIMARY monitor

OSD appears

on the monitor having the ID number you selected.

NOTE:

When the ID selection OSD is being displayed on the PRIMARY monitor

ID selection OSD and then control the monitor you selected.

press the DISPLAY button on the remote controller again to cancel the

HINT

If you set the

monitor to display the OSD screen and change the

emote control mode wrongly and

emote control operation becomes unavailable, press any button on the control panel of the

emote control mode using ADVANCED OPTION. By pressing

emote control for seconds or longer, the emote control mode is initialized to

and holding down the DISPLAY button on the

NORMAL.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Pixel defect policy BDL4635E

Philips strives to deliver the highest quality products. We use some of the industry's most advanced manufacturing processes and

practice stringent quality control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays

are sometimes unavoidable. No manufacturer can guarantee that all panels will be free from pixel defects, but Philips guarantees

that any Plasma- & LCD- displays with an unacceptable number of defects will be repaired during the warranty period in line with

your local guarantee conditions.

This notice explains the different types of pixel defects and defines the acceptable defect level for the BDL4635E LCD screen. In

order to qualify for repair under warranty, the number of pixel defects must exceed a certain level which is given in the

reference table. If the LCD screen is within specification a warranty exchange / claim back will be refused. Additionally, because

some types or combinations of pixel defects are more noticeable than others, Philips sets even higher quality standards for those.

Pixels and Sub-pixels

A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and blue. Many pixels together

form an image. When all sub-pixels of a pixel are lit, the three colored sub-pixels together appear as a single white pixel. When

all are dark, the three colored sub-pixels together appear as a single black pixel. Other combinations of lit and dark sub-pixels

appear as single pixels of other colors.

Types of Pixel Defects + Dot definition

Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several

types of sub-pixel defects within each category.

Dot definition = What is a defective “Dot” ?:

One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to

define a defective dot. This means that a defective dot can consist of one, two or three defective sub-pixels which can

be dark or lit.

One dot = One Pixel; consists of three sub-pixels of Red; Green and Blue

Bright Dot Defects

Bright dot defects appear as pixels or sub-pixels that are always lit or "on". These are the examples of bright dot defects:

Two adjacent lit sub-pixels:

- Red + Blue = Purple

- Red + Green = Yellow

- Green + Blue = Cyan (Light

Blue)

One lit red, green or blue sub-

pixel

Three adjacent lit sub-pixels

(one white dot)

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Dark Dot Defects

Black dot defects appear as pixels or sub-pixels that are always dark or "off". These are the examples of black dot defects:

Two dark dots, specifications

Two adjacent dark dots=

1 pair of dark dots

One dark dot

defines the minimum distance

between dark dots

Proximity of Pixel Defects

Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies

tolerances for the proximity of pixel defects. In the table below you can find specifications about:

•

Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)

Minimum distance between dark dots

Total no. of all defective dots

Pixel Defect Tolerances

In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD-

display must have pixel or sub-pixel defects exceeding the tolerances listed in the following table.

BRIGHT DOT EFFECT

MODEL

ACCEPTABLE LEVEL

BDL4635E

1 lit sub pixel

2 adjacent lit sub pixels

3 adjacent lit sub pixels (one white

pixel)

50% ~ Less Dot (Weak Dot)

Distance between two bright dot

defects*

5mm

Total bright dot defects of all types

BLACK DOT EFFECT

1 dark sub pixel

2 adjacent dark sub pixels

3 adjacent dark sub pixels

Distance between two black dot

defects*

ACCEPTABLE LEVEL

Total black dot defects of all types

TOTAL DOT DEFECTS OF

ALL TYPES

Note:

* 1 or 2 adjacent sub pixel defects = 1 dot defect

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Features

Full HD LCD display 1920x1080p

This display has a resolution that is referred to as Full HD.The state-of-the-art LCD screen technology has the full high-definition widescreen

resolution of 1080 progressive lines, each with 1920 pixels.This allows the best possible picture quality for HD input signals with up to

1080 lines. It produces brilliant flicker-free progressive scan pictures with optimum brightness and superb colors.This vibrant and sharp

image will provide you with an enhanced viewing experience.

Zoom function for tiled matrix

The internal zoom function enables easy implementation of a video wall matrix, without the need for expensive external equipment.

Capable of a vidiwall of 25 displays by dividing up to 5 displays each horizontally and vertically.

Network controllability: RS232

Network controllability allows user to control and adjust monitors remotely through RS232 protocol.

SmartPower

The backlight intensity can be controlled and pre-set by the system to reduce the power consumption by up to 50%, which saves

substantially on energy costs.

Advanced anti image sticking

Static images left on-screen for extended periods of time may leave a "ghost image" or image sticking effect on LCD displays.Although

image sticking in LCD displays is not permanent, you want to prevent this to happen, especially in locations where content is shown 24/7.

Compliant with RoHS standards

Philips designs and produces display products in compliance with strict Restriction of Hazardous Substances (RoHS) standards that restrict

lead and other toxic substances that can harm the environment.

Automatic Long Cable Compensation:

Automatic long cable compensation prevents image quality degradation (color shift and dull signals) caused by long cable lengths.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Troubleshooting

No pictur

•

The signal cable should be completely connected to the display card/computer

The display car should be completely seated in its slot.

Front Power Switch and computer power switch should be in the ON position.

Check to make sur

that

supported mode has been selected on the display car

or system being used.

(Please consult display car

or system manual to change graphics mode.)

•

Check the monitor and your display car

with

espect to compatibility and

ecommended settings.

Check the signal cable connector for bent or pushed-in pins.

If nothing is displayed on the screen when HDCP device is connected,

reset the power of the device.

Power Button does not respond

•

Unplug the power cor

of the monitor from the AC outlet to tur

off

and reset the monitor.

Image persistence

•

Please be awar

“ghost” image of

constant images being displayed for

that LCD

previous image remains visible on the screen. Unlike CR

long period of time should be avoided.

echnology may experience

phenomenon known as Image Persistence. Image Persistence occurs when

monitors, LCD monitors’ image persistence is not permanent, but

alleviate image persistence, tur of the monitor for as long as

residual or

the previous image was displayed. For example,

if an image was on the monitor for one hour and

residual image remains, the monitor should be turned off for one hour to erase the image.

NOTE:

As with all personal display devices, PHILIPS

recommends displaying moving images and using

moving panel saving at regular intervals whenever the

screen is idle or turning of the monitor when not in use.

Image is unstable, unfocused or swimming is apparent

•

Signal cable should be completely attached to the computer

Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment. When the display

mode is changed, the OSD Image Adjust settings may need to be e-adjusted.

Check the monitor and your display car with espect to compatibility and ecommended signal timings.

If your text is garbled, change the video mode to non-interlace and use 60 Hz efresh rate.

•

Image of component signal is greenish

•

Check to see if the CVI input connector is selected.

LED on monitor is not lit (no green or red color can be seen)

•

Power Switch should be in the ON position and power cor

should be connected.

or mouse).

Make certain the computer is not in power-saving mode (touch the keyboard

RED LED on monitor is blinking

•

certain failur

might have occurred, please contact your nearest authorized PHILIPS service facility

Display image is not sized properly

•

Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.

•

Check to make sur

that

supported mode has been selected on the display car

or system being used.

(Please consult display car

or system manual to change graphics mode.)

Advanced anti image sticking

•

static images left on-screen for extended periods of time may leave a "ghost image" or image sticking effect on LCD displays. Although image

sticking in LCD displays is not permanent , you want to prevent this to happen, especially in locations where content is shown almost 24/7.

Selected resolution is not displayed properly

•

Use OSD Display Mode to enter Information menu and confirm that the appropriate

If not, select corresponding option.

resolution has been selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

No Sound

•

Check to see if speaker cable is properly connected.

Check to see if mute is activated.

Check to see if volume is set at minimum.

Remote Control is not available

•

Check the Remote Control’

batteries status.

Check if batteries ar inserted correctly

Check if the Remote Control is pointing at the monitor’s remote sensor

“SCHEDULE”/“SLEEP TIMER

”

function is not working properly

•

The “SCHEDULE” function will be disabled when the “SLEEP TIMER

If the “SLEEP TIMER function is enable and the power to the LCD monitor is turned of

the “SLEEP TIMER will be reset.

”

is set.

”

if the power supply is interrupted unexpectedly, then

”

Stripe Noise

Either light vertical or horizontal stripes may appear, depending on the specifi display pattern. This is no product fault or degradation.

“NO SIGNAL” is displayed on the screen

Image may not be displayed right after HDCP device is connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Specifications

Specifications (BDL4635E)

Product Specifications

Analog Input

Digital Input

46"

0.53025 mm

1920 1080 dots

Over 16 million colors (depending on video car

450 cd/m2 (typ.)

116.8 cm

LCD Module

Diagonal:

Pixel itch:

Resolution:

Color:

used)

Brightness:

Contrast Ratio:

Response time:

4000:1 (typ.)

8 ms (typ.

to G)

iew Angle:

Up and Down 178°, Left and Right 178° (typ.) @CR>10

Design

View Distance:

1100 mm

15.625 15.734, 31.5

50.0 58.0 85.0 Hz

13.5 -165.0 MHz

1018.08 572.67 mm

43.34 inches

Frequency

Horizontal:

91.1 kHz

Vertical:

Pixel Clock

25.0 -165.0 MHz

TMDS

iewable Size

Input Signal

PC-Input:

40.1

22.5 inches

Analog RGB

Video: 0.7 Vp-p

Video:

Input impedance 75 ohm

Separate HV sync: TTL level (Pos./Neg.), Sync-on-green, Composite Sync (0.3Vp-p)

Input Impedance 2.2K ohm

Sync:

Input-terminal: BNC (R,G,B,H,V), 15 Pin Mini D-sub

HDMI

VIDEO Input:

Composite: 1.0 Vp-p

Input impedance 75ohm BNC and RCA-PINJACK-INPUT Y/C

: 1.0 Vp-p C: 0.286 Vp-p Input

Impedance 75 ohm S-TERMINAL-INPUT

Component: 1.0 0.7 Vp-p

Input Impedance 75 ohm BNC-INPUT

RCA PIN-JACK L/R INPUT 2, STEREO Mini Jack INPUT

AUDIO Input:

RS-232C:

In:

Pin Mini D-sub

Output Signal

Analog RGB Video: 0.7 Vp-p with 75 ohm terminated

PC-Output:

Video:

Separate HV sync: TTL level (Pos./Neg.)

15 Pin Mini D-sub

Sync:

Output-terminal:

VIDEO Output:

AUDIO Output:

Speaker Output:

RS-232C:

BNC-OUTPUT

RCA PIN-JACK L/R OUTPUT

External Speaker Jack

1, Composite 1.0 Vp-p with 75 ohm terminated

1, 0.15 rms with 47k ohm terminated

(8 ohm)

Out:

Pin Mini D-sub

Resolutions Supported

640

480 at 60 Hz to 85 Hz

800

600 at 50 Hz, 60Hz to 85 Hz

1024

1280

1360

1280

1600

1920

768 at 50 Hz, 60Hz to 85 Hz

1024 at 60Hz to 85 Hz

1200 at 60 Hz

1080 at 60Hz*

Recommended Resolution

NTSC,PAL,SECAM,4.43NTSC,PAL60 Component:480i,480p,720p,1080i,1080p

3.0 1.3 @100 240 AC, 50 60 Hz

Max 285

Less than 5 W (Power button OFF/Main power switch ON)

40 °C 41-104 ° , Portrait : 5 35 °C 41 95 °F

(Without condensation)

60 °C -4 140 °F

90% (Without condensation)/90%-3.5%x(T

Power Supply

Power Consumption

Power Save:

Operational

Environment

Storage

Environment

Dimension

emperature: Landscape: 5

Humidity: 20

emperature: -20

Humidity: 10

mp-40°C) regarding over 40°C

44.17" (W) x 26.1" (H) x 5.37" (D)

44.17" (W) x 27.68" (H) x 15.93" (D)

50.59" (W) x 37.84" (H) x 10.83" (D)

Net without stand: 1122 mm (W)

663 mm (H)

703.1 mm (H)

885 mm (H)

136.3 mm (D)

Net with stand: 1122 mm (W)

404.7 mm (D)

Gross:

1285 mm (W)

275 mm (D)

Weight

Net without stand: 64.8 lbs

29.1 kg

31.1 kg

36.7 kg

Net with stand:

Gross:

68.6 lbs

86.4 lbs

12 Holes (100 mm pitches)

Optional Multi-purpose Fix Mount

Wall mounting interface

Complied Regulatory and Guidelines

Power Management

UL60950-1/C-UL/EN60950-1/FCC-A/EN55022-A/EN55024/EN61000-3-2/EN61000-3-3 /CE

VESA DPM

Plug

Play

VESA DDC2B, DDC/CI

User's Manual, Power Cord, VGA Cable, DVI-HDMI Cable, BNC TO RCA adapter x 5,

Remote Controller

(For securing cables), Screw for Main switch cover

Holder 2, Main switch cover.

AAA Battery

2, Clamper

prevent from falling), Cable belt x 3

2, Screw for CLAMPER 2, Cable

Accessories

Note: echnical specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Manual BDL4635E

Pin Assignment

1) Analog Video Signal Input (Mini D-SUB 15P): PC-A

Pin No

Name

Video Signal Red

Video Signal Green

Video Signal Blue

Mini D-SUB 15P

GND

DDC-GND

Red-GND

Green-GND

Blue-GND

+5V (DDC)

SYNC-GND

GND

DDC-SDA

H-SYNC

V-SYNC

DDC-SCL

2) S-VIDEO input (MINI DIN 4P):

<S>

MINI DIN 4P

Pin No

Name

GND

Y (Luminance)

(Chroma)

3) HDMI

HDMI 1, HDMI

Pin Assignment of HDMI connector:

TMDS Data0 Shield

TMDS Data0-

TMDS Data2+

SCL

HDMI

TMDS Data2 Shield

TMDS Data2-

SDA

10 TMDS Clock+

11 TMDS Clock Shield

12 TMDS Clock-

13 CEC

DDC/CEC Ground

+5V Power

TMDS Data1+

TMDS Data1 Shield

TMDS Data1-

Hot Plug Detect

14 Reserved (N.C. on device)

TMDS Data0+

4) RS-232C input/output

Pin No

Name

Mini D-SUB 9P

RXD

TXD

GND

RTS

CTS

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications ar

subject to change without notice.

www.philips.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Philips Universal Remote SBC RU630 User Manual
Philips Work Light P 2055 D User Manual
Pioneer TV Cables VSX 1015 S User Manual
Plus Projector UP 1100 User Manual
Polaroid Flat Panel Television LCD 1550 User Manual
Polaroid Security Camera ST 7E User Manual
Poulan Blower 530088124 User Manual
Poulan Snow Blower 424714 User Manual
Premium Home Creations Swimming Pool K 2369 User Manual
ProForm Home Gym 831285871 User Manual