AJ3112
English
Clock Radio
1
Congratulations on your purchase and welcome to Philips!
1
To fully benefit from the support that Philips offers, register your
Register your product and get support at
2
CONTROLS (see fig. 1 )
@
!
1 DISPLAY - shows the clock/ alarm time and status of the set
2 ALARM indicator - lights up when alarm is activated
3 Frequency indicator - shows the radio frequency of your selected waveband
4 REPEAT ALARM / SLEEP OFF
User manual
- switches off the active alarm for a 8-9 minute period
- switches off the sleep function
5 CLOCK - sets the clock time
6 SLEEP
- activates the radio for sleep function
- adjusts the sleep period
7 ALARM RESET- stops the active alarm for 24 hours
8 ALARM - sets the alarm function
0
9
3
4
9 RADIO / ALARM
RADIO ON: switches on the radio
8765
RADIO OFF: switches off the radio/alarm
ALARM - RADIO: activates the radio for alarm
ALARM - BUZ: activates the buzzer for alarm
0 SET TIME HR / MIN
- adjusts the hours / minutes for clock / alarm / sleep time
! Power cord - connects to wall outlet
@ Pigtail - improve FM reception
# VOLUME - adjusts the sound level
$ Battery door - opens to store a 9 volts 6F22 battery (not included) for clock
memory backup.
^
% $ #
% FM/MW - selects FM/MW waveband
^ TUNING - tunes to radio stations
Important notes for users in the U.K.
INSTALLATION
POWER SUPPLY
Meet Philips at the Internet
Mains plug
This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this
type of plug proceed as follows:
1
Check if the power supply, as shown on the type plate located on the bot-
tom of the set, corresponds to your local power supply. If it does not, consult
your dealer or service center.
1
2
3
Remove fuse cover and fuse.
Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.
Refit the fuse cover.
2
3
Connect the plug to the wall outlet.
To disconnect the set from the power supply completely, remove the
plug from the wall outlet.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate plug fitted in its place. If the mains plug contains a fuse, this should
have a value of 3 Amp. If a plug without a fuse is used, the fuse at the distribu-
tion board should not be greater than 5 Amp.
For users in the U.K.: please follow the instructions on the lower left
handed corner of the sheet.
CLOCK MEMORY BACKUP
Note: The severed plug must be disposed of to avoid a possible shock hazard
should it be inserted into a 13 Amp socket elsewhere.
The clock memory backup allows your alarm and clock time settings to be stored
for up to a day when there is a power interruption e.g. power failure. The com-
plete clock radio and display illumination will be switched off. As soon as the
power supply returns, the display will indicate the correct time.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral
(N), brown = live (L). As these colours may not correspond with the colour mark-
ings identifying the terminals in your plug, proceed as follows:
1
2
Remove the battery door to insert a 9 volts 6F22 type battery (not included)
for backup.
Replace the battery door.
•
•
•
Connect the blue wire to the terminal marked N or coloured black.
Connect the brown wire to the terminal marked L or coloured red.
Do not connect either wire to the earth terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
NOTE: If no backup battery is installed or the power interruption is prolonged,
you will need to set the clock and alarm times again.
Before replacing the plug cover, make certain that the cord grip is clamped over
the sheath of the lead - not simply over the two wires.
Batteries contain chemical substances so they should be disposed of
properly.
Copyright in the U.K.
Recording and playback of material may require consent. See Copyright Act 1956
and The Performer’s Protection Acts 1958 to 1972.
Printed in China AJ3112_05_UM_V1.1 (ASDA)
Download from Www.Somanuals.com. All Manuals Search And Download.
|